IMPORTANT MANUAL
Do Not Throw Away
OWNER'S MANUAL
MODEL NUMBER:
WARNING:
Read the Owner's Manual and
follow all Warnings and Safety
Instructions. Failure to do so
can result in serious injury.
PP524A
SNOW THROWER
187877 Rev. 1 04.08.04 BY
Printed in U.S.A.
Always Wear Eye Protection During Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening and front auger
area at all times.
•
•
Do not overload the machine capacity by attempting
to clear snow at too fast a rate.
Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care when
backing up.
Exercise extreme caution when operating on or cross-
ing gravel drives, walks or roads. Stay alert for hidden
hazards or traffic.
•
•
•
Never direct discharge at bystanders or allow anyone
in front of the unit.
After striking a foreign object, stop the engine (motor),
remove wire from the spark plug, thoroughly inspect
snow thrower for any damage, and repair the damage
before restarting and operating the snow thrower.
Disengage power to the auger/impeller when snow
thrower is transported or not in use.
Use only attachments and accessories approved by
the manufacturer of the snow thrower (such as wheel
weights,counterweights,cabs,tirechains,electricstart
kits, etc.).
•
•
If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the cause.
Vibration is generally a warning of trouble.
Stop the engine (motor) whenever you leave the oper-
ating position, before unclogging the auger/impeller
housing or discharge chute and when making any
repairs, adjustments, or inspections.
•
Never operate the snow thrower without good visibility
or light. Always be sure of your footing and keep a firm
hold on the handles. Walk; never run.
•
•
•
Do not overreach. Keep proper footing and balance at
all times.
•
When cleaning, repairing, or inspecting, make certain
all controls are disengaged and the auger/impeller and
all moving parts have stopped. Disconnect the spark
plug wire and keep the wire away from the spark plug
to prevent accidental starting.
This snow thrower is for use on sidewalks, driveways
and other ground level surfaces.
Donotusethesnowthroweronsurfacesaboveground
level such as roofs of residences, garages, porches or
other such structures or buildings.
•
•
Take all possible precautions when leaving the snow
throwerunattended.Disengagetheauger/impeller,stop
engine (motor), and remove key.
MAINTENANCE AND STORAGE
•
Do not run the engine (motor) indoors, except when
starting the engine (motor) and for transporting the
snow thrower in or out of the building.Open the outside
doors.
Check shear bolts and other bolts at frequent intervals
for proper tightness to be sure the equipment is in safe
working condition.
•
Neverstorethesnowthrowerwithfuelinthetankinside
a building where ignition sources are present such as
hot water and space heaters, clothes dryers, and the
like. Allow the engine (motor) to cool before storing in
any enclosure.
WARNING: Exhaust fumes are dan-
gerous (containing CARBON MONOX-
IDE,anODORLESSandDEADLYGAS).
•
Always refer to operator’s guide instructions for im-
portant details if the snow thrower is to be stored for
an extended period.
•
Do not clear snow across the face of slopes. Exercise
extreme caution when changing direction on slopes.
Do not attempt to clear steep slopes.
•
•
Maintain or replace safety and instruction labels, as
necessary.
•
•
Neveroperatethesnowthrowerwithoutproperguards,
plates or other safety protective devices in place.
Run the snow thrower, with auger engaged, a few
minutes after throwing snow to clear the machine and
prevent freeze-up of the auger/impeller.
Never operate the snow thrower near glass enclo-
sures, automobiles, window wells, drop–offs, and the
like without proper adjustment of the snow discharge
angle. Keep children and pets away.
CONGRATULATIONS on your purchase of a new snow
thrower. Ithasbeendesigned,engineeredandmanufactured
to give best possible dependability and performance.
PRODUCT SPECIFICATIONS
Gasoline Capacity 2.0 Quarts
and Type:
Unleaded Regular only
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center/department. We have competent, well-trained tech-
nicians and the proper tools to service or repair this unit.
Oil Type
(API-SF-SJ):
SAE 30 (above 40°F)
SAE 5W-30 or 10W-30 (0° to +40°F)
SAE 0W-30 (below 0°F)
Please read and retain this manual. The instructions will
enable you to assemble and maintain your snow thrower
properly. Always observe the “SAFETY RULES”.
Oil Capacity:
Spark Plug:
21 Ounces
Champion RN4C (Gap: .030")
SERIAL NUMBER: ___________________________
DATE OF PURCHASE: _______________________
CUSTOMER RESPONSIBILITIES
•
•
Read and observe the safety rules.
THEMODELANDSERIALNUMBERSWILLBEFOUND
ONADECALATTACHEDTOTHEREAROFTHESNOW
THROWER HOUSING.
Follow a regular schedule in maintaining, caring for
and using your snow thrower.
•
Follow the instructions under“Maintenance”and“Stor-
age” sections of this owner’s manual.
YOUSHOULDRECORDBOTHSERIALNUMBERAND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY RULES ........................................................ 2-3
PRODUCT SPECIFICATIONS...................................... 3
CUSTOMER RESPONSIBILITIES................................ 3
WARRANTY................................................................ 32
ASSEMBLY / PRE-OPERATION ............................... 5-7
OPERATION ............................................................ 8-13
MAINTENANCE..................................................... 14-15
MAINTENANCE SCHEDULE ..................................... 14
SERVICE AND ADJUSTMENTS ........................... 16-18
STORAGE................................................................... 18
TROUBLESHOOTING ................................................ 19
REPAIR PARTS...................................................... 20-31
PARTS PACKED SEPARATELY IN CARTON
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY / PRE-OPERATION
Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower.
Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for shipping
purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts
bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened
securely. Use the correct tools as necessary to ensure proper tightness.
REMOVE SNOW THROWER FROM CARTON
SPEED
1. Remove all accessible loose parts and parts boxes
CONTROL
from carton.
ROD
2. Cut down all four corners of carton and lay panels
PLASTIC TIE
flat.
3. Remove all packing materials except plastic tie holding
UPPER
HANDLE
speed control rod to lower handle.
4. Remove snow thrower from carton and check carton
thoroughly for additional loose parts.
HANDLE
KNOB
HOW TO SET UPYOUR SNOW THROWER
TOOL BOX (See Fig. 8)
LOWER
HANDLE
A toolbox is provided on your snow thrower. The toolbox
is located on top of the belt cover. Store the extra shear
bolts, nuts and multi-wrench provided in parts bag in the
toolbox.
NOTE: The multi-wrench may be used for assembly of the
chuterotatorheadtosnowthrowerandmakingadjustments
to the skid plates.
UNFOLD UPPER HANDLE
1. Raiseupperhandletotheoperatingpositionandtighten
handle knobs securely.
INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)
FIG. 1
1. Remove plastic tie securing rod to lower handle.
SPEED CONTROL ROD
2. Insert rod into speed control bracket and secure with
retainer spring.
RETAINER
SPRING
SPEED
CONTROL
BRACKET
SPEED
CONTROL
LEVER
FIG. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY / PRE-OPERATION
INSTALL TRACTION DRIVE CONTROL ROD
INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)
(See Figs. 3 and 4)
The traction drive control rod has the long loop on the end
of the spring as shown.
The auger control rod has the short loop on the end of the
spring as shown.
1. Slide rubber sleeve up rod and hook end of spring into
control arm with loop opening up as shown.
1. Slide rubber sleeve up rod and hook end of spring into
pivot bracket with loop opening down as shown.
2. Withtopendofrodpositionedunderrightsideofcontrol
panel, push down on rod and insert end of rod into hole
in auger control bracket. Secure with retainer spring.
2. With top end of rod positioned under left side of control
panel, pushroddownandinserttopendofrodintohole
in drive control bracket. Secure with retainer spring.
TRACTION DRIVE
CONTROL ROD
AUGER
CONTROL
ROD
RUBBER
SLEEVE
RUBBER
SLEEVE
CONTROL
ARM
LOOP
OPENING
DOWN
LOOP
OPENING
UP
PIVOT
BRACKET
FIG. 3
FIG. 5
AUGER
CONTROL
ROD
AUGER
CONTROL
LEVER
TRACTION DRIVE
CONTROL LEVER
RETAINER
SPRING
RETAINER
SPRING
TRACTION
DRIVE
CONTROL
ROD
AUGER
CONTROL
BRACKET
DRIVE
CONTROL
BRACKET
FIG. 4
FIG. 6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY / PRE-OPERATION
INSTALLDISCHARGECHUTE/CHUTEROTATERHEAD
CHECK TIRE PRESSURE
(See Fig. 7)
The tires on your snow thrower were overinflated at the fac-
tory for shipping purposes. Correct and equal tire pressure
is important for best snow throwing performance.
NOTE: The multi-wrench provided in your parts bag may
be used to install the chute rotater head.
•
Reduce tire pressure to 14-17 PSI.
1. Place discharge chute assembly on top of chute base
with discharge opening toward front of snow thrower.
2. Position chute rotater head over chute bracket. If nec-
essary, rotate chute assembly to align square and pin
on underside of chute rotater head with holes in chute
bracket.
3. With chute rotater head and chute bracket aligned,
position chute rotater head on pin and threaded stud
of mounting bracket.
4. Install 3/8 washer and locknut on threaded stud and
tighten securely.
CHUTE
ROTATER
HEAD
3/8 LOCKNUT
3/8 WASHER
CHUTE
BRACKET
PIN
THREADED
STUD
ROTATER HEAD
MOUNTING
BRACKET
FIG. 7
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOWYOUR SNOW THROWER
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATINGYOUR SNOW THROWER. Compare
the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save
this manual for future reference.
These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand
their meaning.
PRIMER
DANGER
OR WARNING
READ AND FOLLOW ALL SAFETY INFORMATION
AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
FORWARD REVERSE
IGNITION KEY.
INSERT TO START
AND RUN,
PULL OUT TO STOP.
DISENGAGED
ENGAGED
SNOW
TRACTION
DISCHARGE
DRIVE CONTROL
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SPARK
PLUG
ENGINE OIL CAP
WITH DIPSTICK
AUGER
CONTROL
LEVER
DISCHARGE CHUTE CONTROL LEVER
SAFETY
IGNITION
KEY
DRIVE SPEED
CONTROL LEVER
GASOLINE
FILLER
CAP
TRACTION
DRIVE
CONTROL
LEVER
CHUTE
DEFLECTOR
CHOKE
CON-
TROL
THROTTLE
/ ENGINE
CONTROL
OIL DRAIN
PLUG
RECOIL
STARTER
HANDLE
FUEL SHUT-OFF VALVE
HANDLE
KNOB
DISCHARGE
CHUTE
PRIMER
MUFFLER
TOOLBOX
NOTE: ITEMS ABOVE
ARE SHOWN IN
THEIR TYPICAL
LOCATION ON THE
ENGINE. ACTUAL
LOCATION MAY VARY
WITH THE ENGINE
ONYOUR UNIT.
SKID PLATE
AUGERS
FIG. 8
MEETS A.N.S.I. SAFETY REQUIREMENTS
Our snow throwers conform to the standards of the American National Standards Institute.
Toolbox - used to store spare shear bolts, locknuts and
wrench.
Drive speed control lever - used to select forward or
reverse motion and speed of snow thrower.
Safety ignition key - must be inserted for the engine to
start and run. Remove when snow thrower is not in use.
Traction drive control lever - used to engage power-pro-
pelled forward or reverse motion of snow thrower.
Recoil starter handle - used for starting the engine.
Auger control lever - used to engage auger motion (throw
snow).
Primer - pumps additional fuel from the carburetor to the
cylinder for use when starting a cold engine.
Discharge chute control lever - used to change the di-
rection the snow is thrown.
Throttle/engine control - used to select either FAST or
SLOW engine speed and to STOP the engine.
Skid plate - used to adjust height of scraper bar from the
ground.
Choke control - used for starting a cold engine.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
The operation of any snow thrower can result
in foreign objects thrown into the eyes, which
canresultinsevereeyedamage. Alwayswear
safety glasses or eye shields while operating
your snow thrower or performing any adjust-
TO USE CHOKE CONTROL (See Fig. 11)
The choke control is located on the engine. Use the choke
control whenever you are starting a cold engine. Do not
use to start a warm engine.
•
To engage choke, turn knob clockwise. Slowly turn
knob counterclockwise to disengage.
ments or repairs.We recommend standard safety glasses
or a wide vision safety mask worn over spectacles.
HOW TO USEYOUR SNOW THROWER
Know how to operate all controls before adding fuel or
attempting to start the engine.
OFF
FULL
STOPPING
TRACTION DRIVE
•
Release traction drive control lever to stop the forward
or reverse movement of the snow thrower.
AUGER
FIG. 11
TO CONTROL SNOW DISCHARGE (See Figs. 12 & 13)
•
Release the auger control lever to stop throwing snow.
ENGINE
WARNING: Snow throwers have ex-
posed rotating parts, which can cause
severe injury from contact,or from ma-
terial thrown from the discharge chute.
Keep the area of operation clear of all
persons, small children and pets at all
times including startup.
1. Move throttle control to “STOP” position.
2. Remove (do not turn) safety ignition key to prevent
unauthorized use.
NOTE: Never use choke to stop engine.
TO USE FUEL SHUT-OFF VALVE (See Fig. 9)
The fuel shut-off valve is located beneath the fuel tank on
the engine. Always operate the snow thrower with the fuel
shut-off valve in the OPEN position.
WARNING: If the discharge chute or
auger become clogged, shut-off en-
gine and wait for all moving parts to
stop. Use a stick, NOT YOUR HANDS,
to unclog the chute and/or auger.
TheDIRECTIONinwhichsnowistobethrowniscontrolled
by the discharge chute control lever.
OFF
•
To change the discharge chute position, press down-
ward on discharge chute control lever and move lever
left or right until chute is in desired position. Be sure
lever springs back and locks into desired position.
OPEN
DISCHARGE CHUTE
CONTROL LEVER
FIG. 9
TO USE THROTTLE CONTROL (See Fig. 10)
Thethrottlecontrolislocatedontheengine.Alwaysoperate
the snow thrower with the engine at full throttle.Full throttle
offers the best snow thrower performance.
FAST
FIG. 12
The DISTANCE that snow is thrown is controlled by the
position of the chute deflector. Set the deflector low to
throw snow a short distance; set the deflector higher to
throw snow farther.
SLOW
•
Tochangethedeflectorposition,loosenknob,movede-
flector to desired position and tighten knob securely.
FIG. 10
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO MOVE FORWARD AND BACKWARD (See Fig. 15)
HIGH POSITION
SELF-PROPELLING, forward and reverse movement of
the snow thrower, is controlled by the traction drive control
lever located on the left side handle.
•
Squeezetractiondrivecontrollevertohandletoengage
the drive system.
•
Release traction drive control lever to stop the forward
or reverse movement of the snow thrower.
SPEED and DIRECTION are controlled by the drive speed
control lever.
KNOB
•
Press downward on the speed control lever and move
lever to desired position BEFORE engaging the trac-
tion drive control lever. Be sure lever springs back and
locks into desired position.
CAUTION: Do not move speed control lever
when traction drive control lever is engaged.
Damage to the snow thrower can result.
CHUTE
DEFLECTOR
LOW POSITION
•
Slower speeds are for heavier snow and faster speeds
are for light snow and transporting the snow thrower. It
is recommended that you use a slower speed until you
are familiar with the operation of the snow thrower.
FIG. 13
TO THROW SNOW (See Fig. 14)
The auger rotation is controlled by the auger control lever
located on the right side handle.
NOTE: When both traction drive and auger control levers
are engaged, the traction drive control lever will lock the
auger control lever in the engaged position.This will allow
you to release your right hand from the handle and adjust
the discharge chute direction without interrupting the snow
throwing process.
•
Squeeze auger control lever to handle to engage the
auger and throw snow.
•
Release the auger control lever to stop throwing snow.
TRACTION DRIVE
CONTROL LEVER
AUGER
CONTROL
LEVER
DRIVE SPEED
CONTROL LEVER
FIG. 14
FIG. 15
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO ADJUST SKID PLATES (See Fig. 16)
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL (See Fig. 17)
NOTE:Thewrenchprovidedinyourpartsbagmaybeused
to adjust the skid plates.
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
Skid plates are located on each side of the auger housing
and adjust the clearance between the scraper bar and the
ground surface. Adjust skid plates evenly to proper height
for current surface conditions. For removal of snow in
normal conditions, such as a paved driveway or sidewalk,
place skid plates in the highest position (lowest scraper
clearance) to give a 1/8" clearance between the scraper
bar and the ground. Use a middle position if the surface
to be cleared is uneven.
1. Check engine oil with snow thrower on level ground.
2. Remove oil fill cap/dipstick and wipe clean, reinsert
the dipstick and screw tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
•
To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
NOTE: It is not recommended to operate the snow thrower
over gravel or rocky surfaces.Objects such as gravel, rocks
or other debris, can easily be picked up and thrown by the
impeller, which can cause serious personal injury, property
damage or damage to the snow thrower.
ADD GASOLINE (See Fig. 17)
•
Fill fuel tank to bottom of tank filler neck. Do not over-
fill. Use fresh, clean, regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
•
If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clearance) position.
WARNING: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
1. Shut off engine and wait for all moving parts to stop.
2. Adjust skid plates by loosening the rear 1/2" hex nut
only,thenmovingskidplatetodesiredposition.Besure
both plates are adjusted evenly. Tighten securely.
CAUTION: Alcohol blended fuels (called gas-
ohol or using ethanol or methanol) can attract
moisture which leads to separation and for-
mation of acids during storage. Acidic gas can
damage the fuel system of an engine while in
storage. To avoid engine problems, the fuel
system should be emptied before storage of
30 days or longer. Empty the gas tank, start
the engine and let it run until the fuel lines and
carburetor are empty. Use fresh fuel next sea-
son. See Storage Instructions for additional
information. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
HIGH POSITION
(LOW GROUND
CLEARANCE)
AUGER
HOUSING
SKID PLATE
1/2" HEX NUT
LOW POSITION (HIGH GROUND CLEARANCE)
FIG. 16
SCRAPER BAR
CHOKE CONTROL
THROTTLE PRIMER
ENGINE OIL
FILL CAP /
DIPSTICK
The scraper bar is not adjustable, but is reversible. After
considerable use it may become worn. When it has worn
almost to the edge of the housing, it can be reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.
SAFETY
IGNITION
KEY
GASOLINE
FILLER CAP
FUEL SHUT-
OFF VALVE
RECOIL
STARTER
HANDLE
NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ONYOUR UNIT.
FIG. 17
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO START ENGINE
•
SNOW THROWING TIPS
Be sure fuel shut-off valve is in the OPEN position.
•
•
•
•
Always operate the snow thrower with the engine at
full throttle. Full throttle offers the best performance.
Your snow thrower engine is equipped with a recoil
starter.
Go slower in deep, freezing or heavy wet snow.Use the
drive speed control, NOT the throttle, to adjust speed.
COLD START
It is easier and more efficient to remove snow imme-
diately after it falls.
1. Insert safety ignition key into the ignition slot until it
clicks. DO NOT turn the key. Keep the extra safety
ignition key in a safe place.
The best time to remove snow is the early morning. At
this time the snow is usually dry and has not been ex-
posed to the direct sun and warming temperatures.
2. Place throttle control in FAST position.
3. Rotate choke control to FULL position.
•
Slightly overlap each successive path to ensure all
snow will be removed.
4. Push the primer four (4) times if the temperature is
below 15°F, or two (2) times if temperature is between
15° and 50°F. If temperature is above 50°F, priming is
not necessary.
•
•
Throw snow downwind whenever possible.
Adjust the skid plates to proper height for current snow
conditions. See “TO ADJUST SKID PLATES” in this
section of this manual.
NOTE: Over priming may cause flooding, preventing the
engine from starting. If you do flood the engine, wait a few
minutes before attempting to start and DO NOT push the
primer.
•
For extremely heavy snow, reduce the width of snow
removal by overlapping previous path and moving
slowly.
5. Pull recoil starter handle quickly. Do not allow starter
rope to snap back.
•
•
•
Keep engine clean and clear of snow during use.This
will help air flow and extend engine life.
6. When the engine starts, release the recoil starter
handle and slowly move the choke control to the OFF
position.
Aftersnow-throwingiscompleted,allowenginetorunfor
a few minutes to melt snow and ice off the engine.
Clean the entire snow thrower thoroughly after each
use and wipe dry so it is ready for next use.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operating
temperature.
WARNING: Do not operate snow
throwerifweatherconditionsimpairvis-
ibility. Throwing snow during a heavy,
windy snowstorm can blind you and be
hazardous to the safe operation of the
snow thrower.
WARM START
Follow the steps above, keeping the choke in the OFF
position. DO NOT push the primer.
BEFORE STOPPING
Run the engine for a few minutes to help dry off any mois-
ture on the engine.
To avoid possible freeze-up of the starter, proceed as fol-
lows:
1. Whiletheengineisrunning,pulltherecoilstarterhandle
with rapid, full arm strokes three or four times.
NOTE: The unusual sound made while pulling the recoil
starter handle will not harm the engine or starter.
IF RECOIL STARTER HAS FROZEN
If the recoil starter has frozen and will not turn the engine,
proceed as follows:
1. Grasp the recoil starter handle and slowly pull as much
rope out of the starter as possible.
2. Release the recoil starter handle and let it snap back
against the starter.
If the engine still fails to start, repeat the above steps.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
GENERAL RECOMMENDATIONS
LUBRICATION CHART
Thewarrantyonthissnowthrowerdoesnotcoveritemsthat
have been subjected to operator abuse or negligence. To
receivefullvaluefromthewarranty, operatormustmaintain
snow thrower as instructed in this manual. Some adjust-
mentswillneedtobemadeperiodicallytoproperlymaintain
your snow thrower.
➀ SAE 30 Motor Oil
See “ENGINE” in
➁
Maintenance section
At least once a season, check to see if you should make
any of the adjustments described in the Service and Ad-
justments section of this manual.
Pivot points
Engine oil
➀
➁
•
At least once a year, you should replace the spark plug
and check belts for wear. A new spark plug will help
your engine run better and last longer.
•
Follow the maintenance schedule in this manual.
NOTE: Use only Original Equipment Manufacturer (OEM)
parts to service this unit. Failure to do so can cause the unit
to malfunction and pose a risk of injury to the operator.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
3. Checkcontrolstobesuretheyarefunctioningproperly.
LUBRICATION
Keep your snow thrower well lubricated
(See “LUBRICATION CHART”).
SNOW THROWER
Always observe the safety rules when performing any
maintenance.
•
Keep tires free of gasoline and oil, which can harm
rubber.
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.
TIRES
•
Maintain proper air pressure in both tires (See“PROD-
UCT SPECIFICATIONS” section in this manual).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
V-BELTS
TO CHANGE ENGINE OIL
Check V-belts for deterioration and wear after every 50
hours of operation and replace if necessary. The belts
are not adjustable. Replace belts if they begin to slip from
wear. (See “TO REMOVE BELT COVER” in the Service
and Adjustments section of this manual).
Determine temperature range anticipated before next oil
change. All oil must meet API service classification SF-SJ.
•
•
•
Be sure snow thrower is on level surface.
Oil will drain more freely when warm.
Catch oil in a suitable container.
TheV-beltsonyoursnowthrowerareofspecialconstruction
andshouldbereplacedbyoriginalequipmentmanufacturer
(OEM)beltsavailablefromyournearestdealer.Usingother
than OEM belts can cause personal injury or damage to
the snow thrower.
NOTE: The left side wheel may be removed from snow
thrower for easier access to the oil drain plug and place-
ment of a suitable container. The unit tilted, resting on the
frame with the left wheel removed, will help drain any oil
trapped inside the engine. (See “TO REMOVE WHEELS”
in the Service and Adjustments section of this manual).
AUGER GEAR CASE
•
The gear case was filled with lubricant to the proper
level at the factory. The only time the lubricant needs
attention is if service has been performed on the gear
case.
1. Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with spark plug.
2. Clean area around drain plug.
•
If lubricant is required, use only Ronex ED #1 grease.
3. Remove drain plug and drain oil in a suitable container.
4. Install drain plug and tighten securely.
TRACTION DRIVE SYSTEM
5. Wipe off any spilled oil from snow thrower and engine.
DO NOT lubricate the drive components inside the snow
thrower. The sprockets, hex shafts, drive disc and friction
wheel require no lubrication. The bearings and bushings
are lifetime lubricated and require no maintenance.
6. Install left wheel (if removed for draining oil).Be sure to
install klick pin into proper hole in wheel axle (See “TO
REMOVE WHEELS” in the Service and Adjustments
section of this manual).
CAUTION:Anylubricatingoftheabovecompo-
nents can cause contamination of the friction
wheel and damage to the drive system of your
snow thrower.
7. Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine.
8. Refill engine with oil through oil dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCTSPECIFICATIONS”sectionofthismanual.
ENGINE
See engine manual.
9. Use gauge on oil fill cap/dipstick for checking level. Be
sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick.
LUBRICATION
10. Wipe off any spilled oil.
Use only high quality detergent oil rated with API service
classification SF-SJ. Select the oil's SAE viscosity grade
according to your expected operating temperature.
MUFFLER
Inspect and replace corroded muffler as it could create a
fire hazard and/or damage.
SPARK PLUG
Replacesparkplugatthebeginningofeachseasonorafter
every100hoursofoperation, whicheveroccursfirst. Spark
plug type and gap setting are shown in the “PRODUCT
SPECIFICATIONS” section of this manual.
CLEANING
IMPORTANT: For best performance, keep snow thrower
housing free of any dirt or trash. Clean the outside of your
snow thrower after each use.
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possible engine damage from running low on oil.
WARNING: Disconnectsparkplugwire
from spark plug and place wire where it
cannotcomeincontactwithsparkplug.
Change the oil after every 50 hours of operation or at least
once a year if the snow thrower is not used for 50 hours
in one year.
•
•
Keepfinishedsurfaces/wheelsfreeofgasoline, oil, etc.
We do not recommend using a garden hose to clean
yoursnowthrowerunlesstheelectricalsystem, muffler
and carburetor are covered to keep water out. Water
in engine can result in shortened engine life.
Checkthecrankcaseoillevelbeforestartingtheengineand
after each five (5) hours of continuous use. Tighten oil fill
cap / dipstick securely each time you check the oil level.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
1. Disengage all controls and move throttle control to
WARNING: To avoid serious injury,
before performing any service or ad-
justments:
STOP position. Wait for all moving parts to stop.
2. Disconnect spark plug wire from spark plug and place
it wear it cannot come in contact with spark plug.
1. Be sure throttle is in STOP position.
2. Remove safety ignition key.
3. Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 locknuts and tighten securely.
3. Make sure the augers and all moving
parts have completely stopped.
CAUTION: Do not substitute. Use only original
equipment capscrew/shear bolts as supplied
with your snow thrower.
4. Disconnect spark plug wire from
spark plug and place wire where it
cannot come in contact with plug.
4. Connect spark plug wire to spark plug.
SNOW THROWER
1/4-20
LOCKNUT
1/4-20 x 1-5/8
CAPSCREW /
SHEAR BOLT
1/4-20 x 2
SHOULDER /
SHEAR BOLT
TO ADJUST SNOW THROWER HEIGHT
See “TO ADJUST SKID PLATES” and “SCRAPER BAR”
in the Operation section of this manual.
IMPELLER HUB
CHUTE DEFLECTOR
IMPELLER
SHAFT
The chute deflector, attached to the top of the discharge
chute, is provided to direct discharging snow away from
the operator. If the deflector becomes damaged, it should
be replaced.
WARNING: To avoid serious injury,
never operate your snow thrower with
the deflector removed or damaged.
•
Tochangedirectionand/ordistancesnowisdischarged,
see “TO CONTROL SNOW DISCHARGE” in the Op-
eration section of this manual.
AUGER
HUB
SHEAR BOLTS (See Fig. 18)
1/4-20
LOCKNUT
AUGER SHEAR BOLTS
AUGER HUB
AUGER SHAFT
Both right and left-hand augers are secured to the auger
shaft with a shoulder/shear bolt and hex nut. Should a for-
eign object or ice become lodged in the augers, the shear
bolts are designed to break, preventing damage to any
other components. If one or both augers do not turn when
auger control lever is engaged, check to see if one or both
of the bolts have sheared. To replace the shear bolts:
FIG. 18
TO REMOVE BELT COVER (See Fig. 19)
1. Remove the two (2) screws securing belt cover to
frame.
2. Remove belt cover.
1. Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
•
Replace belt cover by installing cover and screws and
tighten securely.
2. Disconnect spark plug wire from spark plug and place
it wear it cannot come in contact with spark plug.
BELT
COVER
3. Align hole in auger hub with hole in auger shaft and
install a new 1/4-20 x 2" shoulder/shear bolt. Install
1/4-20 lock nut and tighten securely.
CAUTION: Do not substitute. Use only original
equipment shear bolts as supplied with your
snow thrower.
4. Connect spark plug wire to spark plug.
IMPELLER SHEAR BOLTS
The impeller is secured to the impeller shaft with two (2)
capscrew/shear bolts and hex nuts.Should a foreign object
or ice become lodged in the impeller, the capscrews are
designed to break, preventing damage to any other com-
ponents. If impeller does not turn when auger control lever
is engaged, check to see if the capscrews have sheared.
To replace the capscrew/shear bolts:
FRAME
SCREWS
FIG. 19
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
TO REPLACE BELTS (See Fig. 20)
The auger and traction drive belts are not adjustable. If the
belts are damaged or begin to slip from wear, they should
be replaced.It is recommended that the belt(s) be replaced
by a qualified service center.
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into
the square hole in idler arm and rotate ratchet clockwise
to relieve tension.
8. With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
NOTE: It is recommended that both the auger and traction
drive belt be replaced at the same time.
9. Place auger belt around and inside the groove of auger
pulley only.
TheV-beltsonyoursnowthrowerareofspecialconstruction
andshouldbereplacedbyoriginalequipmentmanufacturer
(OEM)beltsavailablefromyournearestdealer.Usingother
than OEM belts can cause personal injury or damage to
the snow thrower.
10. While your assistant slowly raises handles to rejoin
the auger housing and frame assembly, pull up on the
auger belt and squeeze sides together above pulley
so belt is fully seated in groove of pulley.
11. Bring snow thrower completely together and check
carefully for proper routing of belts. If auger belt has
becomedislodgedfromthepulley(bycatchingtheidler
arm bracket while bringing snow thrower together),
separate the snow thrower and repeat step 10. Belt
must be fully seated in pulley groove when bringing
the snow thrower together.
WARNING: Belt replacement requires
separation of the snow thrower. While
separating the auger housing from the
frame assembly, it is important that an
assistantstandintheoperatingposition
andholdthesnowthrowerhandles.Se-
rious personal injury and/or damage to
theunitcouldoccurifthesnowthrower
should fall during the belt changing
process.
12. Install the two (2) hex bolts and lock washers and
tighten securely.
13. INSTALLENGINEPULLEY-Placebeltinpulleygroove
and slide pulley on crankshaft. Install flat washer, lock-
washer and bolt and tighten securely (30-35 ft. lbs.
torque). Make sure belt is inside belt keeper.
FRAME
ASSEMBLY
AUGER
HOUSING
14. INSTALL BELT COVER and two (2) screws. Tighten
securely.
15. INSTALL DISCHARGE CHUTE – See “INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER HEAD” in the
Assembly / Pre-Operation section of this manual.
BELT KEEPER
TRACTION DRIVE BELT
ENGINE
HANDLES
1. REMOVEGASOLINEFROMFUELTANK-Draingaso-
line from fuel tank into a suitable container, outdoors,
away from fire or flame. Wipe up any spilled gasoline.
FLAT WASHER
PULLEY
LOCKWASHER
BOLT
2. REMOVE DISCHARGE CHUTE - Loosen locknut
securing chute rotator head to mounting bracket only
enough to allow chute rotator head to be raised and
discharge chute to be removed from snow thrower.
AUGER
BELT
IDLER ARM
SQUARE
HOLE
3. REMOVE BELT COVER - See “TO REMOVE BELT
COVER” in this section of this manual.
CLUTCHING
IDLER ARM
BRACKET
4. REMOVEENGINEPULLEY-Removebolt,lockwasher
and flat washer securing pulley to engine crankshaft.
Remove outside (auger) pulley only from crankshaft.
AUGER PULLEY
5. SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
remove the two (2) bolts and lock washers holding
auger housing and frame together.
BOLT
LOCK
WASHER
WARNING: As the last bolt is removed,
have your assistant carefully lower the
handles down to the ground.
6. REMOVE AUGER BELT from around pulley.
FRAME
AUGER
7. RELIEVE TENSION ON TRACTION DRIVE BELT
IDLER and remove traction drive belt from around
pulleys.
HOUSING
FIG. 20
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TO REMOVE WHEELS (See Fig. 21)
Remove the klik pin and remove wheel from axle.
NOTE: To seal punctures or prevent flat tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer.Tire sealant also prevents tire dry rot and corrosion.
•
IMPORTANT:When installing wheel, be sure to use the in-
nermost hole in axle and the wheel hub hole. To disengage
drive system from the wheels (for pushing or transporting
the snow thrower), remove klik pin from wheel hub and
insert pin into the outermost hole in axle only.
ENGINE
See engine manual.
CARBURETOR
Your carburetor is not adjustable. Engine performance
should not be affected at altitudes up to 7,000 feet (2,134
meters). If your engine does not operate properly due to
suspected carburetor problems, take your snow thrower to
a qualified service center.
KLIK PIN
OUTER HOLE
ENGINE SPEED
Never tamper with the engine governor, which is factory set
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be dangerous and will
void the warranty. If you think the engine-governed high
speed needs adjusting, contact a qualified service center,
which has proper equipment and experience to make any
necessary adjustments.
INNER
HOLE
WHEEL
WHEEL HUB
FIG. 21
STORAGE
Immediately prepare your snow thrower for storage at the
end of the season or if the unit will not be used for 30 days
or more.
•
•
•
Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
WARNING: Never store the snow
throwerwithgasolineinthetankinside
a building where fumes may reach an
open flame, spark or pilot light as on a
furnace, water heater, clothes dryer or
gasappliance. Allowtheenginetocool
before storing in any enclosure.
Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in min-
imizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.
SNOW THROWER
When snow thrower is to be stored for a period of time,
clean it thoroughly, remove all dirt, grease, leaves, etc.
Store in a clean, dry area.
ENGINE OIL
Drain oil (with engine warm) and replace with clean en-
gine oil. (See “ENGINE” in the Maintenance section of
this manual).
1. Clean entire snow thrower (See “CLEANING” in the
Maintenance section of this manual).
CYLINDER
1. Remove spark plug.
2. Inspect and replace belts, if necessary (See “TO RE-
PLACEBELTS”intheServiceandAdjustmentssection
of this manual).
2. Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.
3. Lubricate as shown in the Maintenance section of this
manual.
3. Pullrecoilstarterhandleslowlyafewtimestodistribute
oil.
4. Besurethatallnuts,bolts,screws,andpinsaresecurely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
4. Replace with new spark plug.
OTHER
5. Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
•
Do not store gasoline from one season to another.
•
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
ENGINE
See engine manual.
•
•
If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.
FUEL SYSTEM
Coveryoursnowthrowerwithasuitableprotectivecover
thatdoesnotretainmoisture.Donotuseplastic.Plastic
cannotbreathe,whichallowscondensationtoformand
will cause your snow thrower to rust.
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
fuelhose,ortankduringstorage.Also,alcoholblendedfuels
(called gasohol or using ethanol or methanol) can attract
moisture which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel system of
an engine while in storage.
IMPORTANT: Never cover snow thrower while engine/
exhaust area is still warm.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
See appropriate section in manual unless directed to a qualified service center.
PROBLEM
CAUSE
CORRECTION
Does not start
1. Fuel shut-off valve (if so
equipped) in OFF position.
1. Turn fuel shut-off valve to OPEN position.
2. Safety ignition key
is not inserted.
2. Insert safety ignition key.
3. Out of fuel.
3. Refill fuel tank with fresh, clean gasoline.
4. Move throttle to FAST position.
5. Move to FULL position.
6. Prime as instructed in the Operation section of this manual.
7. Wait a few minutes before restarting, DO NOT prime.
8. Connect wire to spark plug.
4. Throttle in STOP position.
5. Choke in OFF position.
6. Primer not depressed.
7. Engine is flooded.
8. Spark plug wire is
disconnected.
9. Bad spark plug.
10. Stale fuel.
11. Water in fuel.
9. Replace spark plug.
10. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
11. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
Loss of power
1. Spark plug wire loose.
2. Throwing too much snow.
3. Fuel tank cap is covered
with ice or snow.
1. Reconnect spark plug wire.
2. Reduce speed and width of swath.
3. Remove ice and snow on and around fuel tank cap.
4. Dirty or clogged muffler.
4. Clean or replace muffler.
Engine idles or
runs roughly
1. Choke is in FULL position.
2. Blockage in fuel line.
3. Stale fuel.
4. Water in fuel.
5. Carburetor is in need of
adjustment or overhaul.
1. Move choke to OFF position.
2. Clean fuel line.
3. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
4. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
5. Contact a qualified service center.
Excessive
vibration
1. Loose parts or damaged
augers or impeller.
1. Tighten all fasteners. Replace damaged parts.
If vibration remains, contact a qualified service center.
Recoil starter
is hard to pull
1. Frozen recoil starter.
1. See “IF RECOIL STARTER HAS FROZEN”
in the Operation section of this manual.
Loss of traction 1. Drive belt is worn.
1. Check / replace drive belt.
2. Check / reinstall drive belt.
drive / slowing
of drive speed
2. Drive belt is off of pulley.
3. Friction drive wheel is worn. 3. Contact a qualified service center.
Loss of snow
discharge or
slowing of
1. Auger belt is off of pulley.
2. Auger belt is worn.
3. Clogged discharge chute.
1. Check / reinstall auger belt.
2. Check / replace auger belt.
3. Clean snow chute.
snow discharge 4. Augers / impeller jammed.
4. Remove debris or foreign object from augers / impeller.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from de-
fects in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer
purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any
part which we find to be defective due to materials or workmanship. This Warranty is subject to the following limita-
tions and exclusions.
1. This warranty does not apply to the engine or components parts thereof. Please refer to the applicable manu-
facturer's warranty on these items.
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of
the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid
by the purchaser unless such return is requested by Electrolux Home Products.
3. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date
of original purchase.
4. ThisWarranty applies only to products which have been properly assembled, adjusted, operated, and maintained
in accordance with the instructions furnished. This Warranty does not apply to any product which has been
subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear
of the product.
5. Exclusions: Excluded from this Warranty are belts, shear pins, normal wear, normal adjustments, standard
hardware and normal maintenance.
6. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.
Should you have any unanswered questions concerning this Warranty, please contact:
In Canada contact:
Electrolux Home Products, Inc.
Outdoor Products Customer Service Dept.
250 Bobby Jones Expressway
Augusta, GA 30909 USA
Electrolux Canada Corp.
7075 Ordan Drive
Mississauga, Ontario
L5T 1K6
giving the complete mfg. ID#, serial number and date of purchase of your product and the name and address of the
authorized dealer from whom it was purchased.
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED
WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WAR-
RANTIES. Some areas do not allow the limitation of consequential damages or limitations of how long an implied
Warranty may last, so the above limitations or exclusions may not apply to you.This Warranty gives you specific legal
rights, and you may have other rights which vary from locale to locale.
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.
Download from Www.Somanuals.com. All Manuals Search And Download.
|