Poulan Chainsaw 530088311 User Manual

R
Instruction Manual  
Manual de Instrucciones  
Manuel d’Instructions  
For Occasional Use Only  
WARNING:  
Read and follow all Safety Rules and Operating Instructions before  
using this product. Failure to do so can result in serious injury.  
ADVERTENCIA:  
Lea el manual de instrucciones y siga todas las advertencias e en-  
strucciones de seguridad. El no hacerlo puede resultar en lesiones  
graves.  
AVERTISSEMENT:  
Lire le manuel d’instructions et bien respecter tous les avertisse-  
ments et toutes les instructions de sécurité. Tout défaut de le faire  
pourrait entraîner des blessures graves.  
Electrolux Home Products, Inc.  
250 Bobby Jones Expressway  
Augusta, GA 30907  
Electrolux Canada Corporation  
6150 McLaughlin Road  
Mississauga, ON L5R 4C2  
Copyright E2002 Electrolux Home Products, Inc.  
530088311  
4/10/02  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S Carefully plan your sawing operation in ad-  
vance. Do not start cutting until you have a  
clear work area, secure footing, and, if you  
are felling trees, a planned retreat path.  
marked container for all fuel purposes.  
Wipe up all fuel spills before starting saw.  
S Move at least 10 feet (3 meters) from fuel-  
ing site before starting engine.  
S Turn the engine off and let saw cool in a  
non-combustible area, not on dry leaves,  
straw, paper, etc. Slowly remove fuel cap  
and refuel unit.  
OPERATE YOUR SAW SAFELY  
S Do not operate a chain saw with one hand.  
Serious injury to the operator, helpers, by-  
standers or any combination of these per-  
sons may result from one-handed opera-  
S Store the unit and fuel in an area where fuel  
vapors cannot reach sparks or open  
flames from water heaters, electric motors  
or switches, furnaces, etc.  
tion.  
A
chain saw is intended for  
two-handed use.  
S Operate the chain saw only in a well-venti-  
lated outdoor area.  
KICKBACK  
S Do not operate saw from a ladder or in a  
tree.  
WARNING: Avoid kickback which  
can result in serious injury. Kickback is the  
backward, upward or sudden forward motion  
of the guide bar occurring when the saw  
chain near the upper tip of the guide bar con-  
tacts any object such as a log or branch, or  
when the wood closes in and pinches the  
saw chain in the cut. Contacting a foreign ob-  
ject in the wood can also result in loss of  
chain saw control.  
S Rotational Kickback can occur when the  
moving chain contacts an object at the up-  
per tip of the guide bar. This contact can  
cause the chain to dig into the object,  
which stops the chain for an instant. The  
result is a lightning fast, reverse reaction  
which kicks the guide bar up and back to-  
ward the operator.  
S Pinch-Kickback can occur when the the  
wood closes in and pinches the moving  
saw chain in the cut along the top of the  
guide bar and the saw chain is suddenly  
stopped. This sudden stopping of the  
chain results in a reversal of the chain  
force used to cut wood and causes the  
saw to move in the opposite direction of the  
chain rotation. The saw is driven straight  
back toward the operator.  
S Make sure the chain will not make contact  
with any object while starting the engine.  
Never try to start the saw when the guide  
bar is in a cut.  
S Do not put pressure on the saw at the end  
of the cut. Applying pressure can cause  
you to lose control when the cut is com-  
pleted.  
S Stop the engine before setting the saw  
down.  
S Do not operate a chain saw that is dam-  
aged, improperly adjusted, or not com-  
pletely and securely assembled. Always  
replace bar, chain, hand guard, or chain  
brake immediately if it becomes damaged,  
broken or is otherwise removed.  
S With the engine stopped, hand carry the  
chain saw with the muffler away from your  
body, and the guide bar and chain to the  
rear, preferably covered with a scabbard.  
MAINTAIN YOUR SAW IN GOOD  
WORKING ORDER  
S Have all chain saw service performed by a  
qualified service dealer with the exception  
of the items listed in the maintenance sec-  
tion of this manual. For example, if improp-  
er tools are used to remove or hold the fly-  
wheel when servicing the clutch, structural  
damage to the flywheel can occur and  
cause the flywheel to burst.  
S Pull-In can occur when the moving chain  
contacts a foreign object in the wood in the  
cut along the bottom of the guide bar and the  
saw chain is suddenly stopped. This sudden  
stopping pulls the saw forward and away  
from the operator and could easily cause the  
operator to lose control of the saw.  
S Make certain the saw chain stops moving  
when the throttle trigger is released. For  
correction, refer to CARBURETOR AD-  
JUSTMENTS.  
Avoid Pinch--Kickback:  
S Never modify your saw in any way.  
S Keep the handles dry, clean, and free of oil  
or fuel mixture.  
S Be extremely aware of situations or ob-  
structions that can cause material to pinch  
the top of or otherwise stop the chain.  
S Do not cut more than one log at a time.  
S Do not twist the saw as the bar is with-  
drawn from an undercut when bucking.  
S Keep fuel and oil caps, screws, and fas-  
teners securely tightened.  
S Use only Poulan PROR accessories and  
replacement parts as recommended.  
Avoid Pull--In:  
S Always begin cutting with the engine at full  
speed and the saw housing against wood.  
S Use wedges made of plastic or wood.  
Never use metal to hold the cut open.  
HANDLE FUEL WITH CAUTION  
S Do not smoke while handling fuel or while  
operating the saw.  
S Eliminate all sources of sparks or flame in  
the areas where fuel is mixed or poured.  
There should be no smoking, open flames,  
or work that could cause sparks. Allow en-  
gine to cool before refueling.  
S Mix and pour fuel in an outdoor area on  
bare ground; store fuel in a cool, dry, well  
ventilated place; and use an approved,  
Kickback Path  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Avoid Obstructions  
Elbow locked  
Clear The Working Area  
Thumb on underside of  
handlebar  
REDUCE THE CHANCE OF  
KICKBACK  
S Keep a good, firm grip on the saw with both  
hands when the engine is running and  
don’t let go. A firm grip will help you reduce  
kickback and maintain control of the saw.  
Keep the fingers of your left hand encir-  
cling and your left thumb under the front  
handlebar. Keep your right hand com-  
pletely around the rear handle whether  
your are right handed or left handed. Keep  
your left arm straight with the elbow  
locked.  
S Recognize that kickback can happen.  
With a basic understanding of kickback,  
you can reduce the element of surprise  
which contributes to accidents.  
S Never let the moving chain contact any ob-  
ject at the tip of the guide bar.  
S Keep the working area free from obstruc-  
tions such as other trees, branches, rocks,  
fences, stumps, etc. Eliminate or avoid  
any obstruction that your saw chain could  
hit while you are cutting. When cutting a  
branch, do not let the guide bar contact  
branch or other objects around it.  
S Keep your saw chain sharp and properly  
tensioned. A loose or dull chain can in-  
crease the chance of kickback occurring.  
Follow manufacturers chain sharpening  
and maintenance instructions. Check ten-  
sion at regular intervals with the engine  
stopped, never with the engine running.  
Make sure the chain brake nuts are se-  
curely tightened after tensioning the chain.  
S Begin and continue cutting at full speed. If  
the chain is moving at a slower speed,  
there is greater chance of kickback occur-  
ring.  
S Position your left hand on the front handle-  
bar so it is in a straight line with your right  
hand on the rear handle when making  
bucking cuts. Never reverse right and left  
hand positions for any type of cutting.  
S Stand with your weight evenly balanced on  
both feet.  
S Stand slightly to the left side of the saw to  
keep your body from being in a direct line  
with the cutting chain.  
S Do not overreach. You could be drawn or  
thrown off balance and lose control of the  
saw.  
S Do not cut above shoulder height. It is diffi-  
cult to maintain control of saw above  
shoulder height.  
S Cut one log at a time.  
S Use extreme caution when re-entering a  
previous cut.  
KICKBACK SAFETY FEATURES  
S Do not attempt cuts starting with the tip of  
the bar (plunge cuts).  
WARNING: The following features  
are included on your saw to help reduce the  
hazard of kickback; however, such features  
will not totally eliminate this danger. As a  
chain saw user, do not rely only on safety de-  
vices. You must follow all safety precau-  
tions, instructions, and maintenance in this  
manual to help avoid kickback and other  
forces which can result in serious injury.  
S Reduced--Kickback Guide Bar, designed  
with a small radius tip which reduces the  
size of the kickback danger zone on the  
bar tip. A Reduced--Kickback Guide Bar  
has been demonstrated to significantly re-  
duce the number and seriousness of kick-  
backs when tested in accordance with  
safety requirements for gasoline powered  
S Watch for shifting logs or other forces that  
could close a cut and pinch or fall into  
chain.  
S Use the Reduced--Kickback Guide Bar  
and Low--Kickback Chain specified for  
your saw.  
MAINTAIN CONTROL  
Stand to
of the sa
chain saws as set by ANSI B175.1.  
Thumb on  
underside of  
handlebar  
Reduced Kickback Symmetrical Guide Bar  
Never r
hand positions  
Small Radius Tip  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
action may push the guide bar rapidly back  
toward the operator. Either of these events  
may cause you to lose control of the saw  
which could result in serious injury or even  
death. DO NOT RELY UPON ANY OF THE  
DEVICES BUILT INTO YOUR SAW. YOU  
SHOULD USE THE SAW PROPERLY AND  
CAREFULLY TO AVOID KICKBACK. Re-  
duced--kickback guide bars and low--kick-  
back saw chains reduce the chance and  
magnitude of kickback and are recom-  
mended. Your saw has a low kickback chain  
and bar as original equipment. Repairs on a  
chain brake should be made by an autho-  
rized servicing dealer. Take your unit to the  
place of purchase if purchased from a ser-  
vicing dealer, or to the nearest authorized  
master service dealer.  
S Tip contact in some cases may cause a light-  
ning fast reverse REACTION, kicking the  
guide bar up and back toward the operator.  
S Pinching the saw chain along the top of the  
guide bar may push the guide bar rapidly  
back toward the operator.  
S Either of these reactions may cause you to  
lose control of the saw which could result  
in serious injury.Do not rely exclusively  
upon the safety devices built into your saw.  
Symmetric
Large Radius Tip  
S Low--Kickback Chain, designed with a  
contoured depth gauge and guard link  
which deflect kickback force and allow  
wood to gradually ride into the cutter. Low--  
Kickback Chain has met kickback per-  
formance requirements when tested on a  
representative sample of chain saws be-  
low 3.8 cubic inch displacement specified  
in ANSI B175.1.  
Contoured Depth Gauge  
Elongated Guard Link  
Deflects  
kickback force  
Low---Kickback  
and allows wood  
Chain  
to gradually ride  
into cutter  
Can Obstruct Material  
Not a Low---Kickback Chain  
WARNING: Computed kickback  
angle (CKA) listed on your saw and listed in  
the CKA table below represents angle of  
kickback your bar and chain combinations  
will have when tested in accordance with  
CSA and ANSI standards. When purchasing  
replacement bar and chain, considerations  
should be given to the lower CKA values.  
Lower CKA values represent safer angles to  
the user, higher values indicate more angle  
and higher kick energies. Computed angles  
represented in the non-activated column in-  
dicate total energy and angle associated  
without activation of the chain brake during  
kickback. Activated angle represents chain  
stopping time relative to activation angle of  
chain brake and resulting kick angle of saw.  
In all cases lower CKA values represent a  
safer operating environment for the user.  
The following guide bar and chain combina-  
tions meet kickback requirements of CSA  
Z62.1, Z62.3, & ANSI B175.1 when used on  
saws listed in this manual. Use of bar and  
chain combinations other than those listed is  
not recommended and may not meet the  
CKA requirements per standard.  
S Front Hand Guard, designed to reduce the  
chance of your left hand contacting the chain  
if your hand slips off the front handlebar.  
S Position of front and rear handlebars, de-  
signed with distance between handles and  
“in-line” with each other. The spread and  
“in-line” position of the hands provided by  
this design work together to give balance  
and resistance in controlling the pivot of  
the saw back toward the operator if kick-  
back occurs.  
CHAIN BRAKE AND CKA ANGLE  
S Chain Brake, designed to stop the chain in  
the event of kickback.  
WARNING: WE DO NOT REP-  
RESENT AND YOU SHOULD NOT AS-  
SUME THAT THE CHAIN BRAKE WILL  
PROTECT YOU IN THE EVENT OF A  
KICKBACK. Kickback is a lightning fast ac-  
tion which throws the bar and rotating chain  
back and up toward the operator. Kickback  
can be caused by allowing contact of the bar  
tip in the danger zone with any hard object.  
Kickback can also be caused by pinching the  
saw chain along the top of the guide bar. This  
Computed kickback angle (CKA) Table  
BAR  
Length  
MODEL  
220  
260  
P/N  
CHAIN P/N  
CKA without chain brake  
8_  
6_  
16!  
18!  
530044834  
530044835  
952051480  
952051481  
NOTE: If this saw is to be used for commer-  
cial logging, a chain brake is required and shall  
not be removed or otherwise disabled to com-  
ply with Federal OSHA Regulations for Com-  
mercial Logging.  
SAFETY NOTICE: Exposure to vibrations  
through prolonged use of gasoline powered  
hand tools could cause blood vessel or nerve  
damage in the fingers, hands, and joints of  
people prone to circulation disorders or  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
abnormal swellings. Prolonged use in cold  
weather has been linked to blood vessel  
damage in otherwise healthy people. If  
symptoms occur such as numbness, pain,  
loss of strength, change in skin color or texture,  
or loss of feeling in the fingers, hands, or joints,  
discontinue the use of this tool and seek  
medical attention. An anti-vibration system  
does not guarantee the avoidance of these  
problems. Users who operate power tools on  
a continual and regular basis must monitor  
closely their physical condition and the  
condition of this tool.  
Location of shipping spacer  
Chain Brake  
Nuts  
Chain
SPECIAL NOTICE: Your saw is equipped  
with a temperature limiting muffler and spark  
arresting screen which meets the  
requirements of California Codes 4442 and  
4443. All U.S. forest land and the states of  
California, Idaho, Maine, Minnesota, New  
Jersey, Oregon, and Washington require by  
law that many internal combustion engines  
to be equipped with a spark arresting screen.  
If you operate a chain saw in a state or locale  
where such regulations exist, you are legally  
responsible for maintaining the operating  
condition of these parts. Failure to do so is  
a violation of the law. Refer to the SERVICE  
section for maintenance of the spark  
arresting screen.  
Bar Tool  
3. Turn adjusting screw on bar counter-  
clockwise to move the tensioning rack as  
far as it will go toward the front of the bar.  
Adjusting  
Screw  
Tensioning Rack  
4. Slide the bar behind clutch drum until bar  
stops against clutch drum sprocket.  
Failure to follow all Safety Rules and Precau-  
tions can result in serious injury. If situations  
occur which are not covered in this manual,  
use care and good judgement. If you need  
assistance, contact your authorized service  
dealer or call 1-800--554--6723.  
STANDARDS: This saw is listed by Under-  
writer’s Laboratories, Inc., and the Canadian  
Standards Association in accordance with:  
Mount the Bar  
5. Prepare the chain by checking the proper  
direction. Without following the illustration it  
is easy to place the chain on the saw in the  
wrong direction. Use the illustration of the  
chain to determine the proper direction.  
ANSI B175.1-2000  
American National  
Standard for Powered Tools -- Gasoline  
Powered Chain Saw -- Safety Requirements  
CSA Z62.1--1995 Chain Saws -- Occupa-  
tional Health and Safety  
CSA Z62.3--1996 Chain Saw Kickback Oc-  
cupational Health and Safety  
Tip of  
Bar  
ASSEMBLY  
Protective gloves (not provided) should be  
worn during assembly.  
ATTACHING THE BAR & CHAIN (If not  
already attached)  
CUTTERS MUST FACE IN  
DIIRECTION OF ROTATION  
WARNING: If received assembled,  
repeat all steps to ensure your saw is prop-  
erly assembled and all fasteners are secure.  
Always wear gloves when handling the  
chain. The chain is sharp and can cut you  
even when it is not moving!  
1. Loosen and remove the chain brake nuts  
and the chain brake from the saw.  
2. Remove the plastic shipping spacer (if  
present).  
Depth Gauge  
Cutters  
Drive Links  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Place the chain over and behind the  
clutch, fitting the drive links in the clutch  
drum sprocket.  
Adjusting the tension:  
Chain tension is very important. Chain  
stretches during use. This is especially true  
during the first few times you use your saw.  
Always check chain tension each time you  
use and refuel your saw.  
An adjusting screw (located on the guide ba) r  
is used to adjust the tension of the chain (see  
illustration).  
S Turn adjusting screw clockwise until chain  
solidly contacts bottom of guide bar rail.  
Place chain onto the sprocket  
Guide bar  
7. Fit bottom of drive links between the  
teeth in the sprocket in the nose of the  
guide bar.  
8. Fit chain drive links in to bar groove.  
9. Pull the bar forward until the chain is  
snug in the groove of the bar. Ensure all  
drive links are in the bar groove.  
Adjusting  
Screw  
10. Hold guide bar against the saw frame  
and install the chain brake.  
S Using the screwdriver end of the bar tool,  
roll chain around guide bar to ensure all  
links are in bar groove.  
11. Replace the chain brake nuts and tighten  
finger tight. Once the chain is tensioned  
you will need to tighten chain brake nuts.  
S Lift up tip of guide bar to check for sag. Re-  
lease tip of guide bar, then turn adjusting  
screw until sag does not exist.  
CHAIN TENSION (Including units with  
chain already installed)  
S Tighten bar clamp nuts securely with the  
bar tool.  
NOTE: When adjusting chain tension,  
make sure the chain brake nuts are finger  
tight only. Attempting to tension the chain  
when the chain brake nuts are tight can  
cause damage.  
Checking the tension:  
Use the screwdriver end of the chain adjust-  
ment tool (bar tool) to move the chain around  
the bar. If the chain does not rotate, it is too  
tight. If too loose, the chain will sag below the  
bar.  
S Use the screwdriver end of the bar tool to  
move chain around guide bar.  
S If chain does not rotate, it is too tight.  
Slightly loosen bar clamp nuts and loosen  
chain by turning the adjusting screw. Re-  
tighten bar clamp nuts.  
S If chain is too loose, it will sag below the  
guide bar. DO NOT operate the saw if the  
chain is loose.  
WARNING: If the saw is operated  
with a loose chain, the chain could jump off  
the guide bar and result in serious injury.  
Chain Adjustment  
Tool (Bar Tool)  
Chain Brake Nuts  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOW YOUR SAW  
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR  
CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of  
the various controls and adjustments. Save this manual for future reference.  
Chain  
Adjustment Tool  
Front Handle  
Starter Rope  
ON/STOP  
Front Hand Guard  
Muffler  
Switch  
Chain  
Primer  
Bulb  
Bar  
Sprocket Hole  
Starter  
Housing  
Bar Oil Fill Cap  
Fuel Mix Fill Cap  
Cylinder Cover  
ion  
vel  
Rear  
Hand
Bar  
Th
Trigger  
Fast Idle  
Lever  
Sprocket  
Chain  
Brake  
Chain  
Catcher  
Hole  
ON/STOP SWITCH  
CHAIN BRAKE  
The ON/STOP SWITCH is used to stop the  
engine.  
The CHAIN BRAKE is a device designed to  
stop the chain if kickback occurs. The chain  
brake activates automatically in the event of  
kickback. The chain brake activates manu-  
ally if the front hand guard is pushed forward.  
The chain brake is disengaged by pulling the  
front hand guard back toward the front han-  
dle as far as possible.  
THROTTLE TRIGGER  
The THROTTLE TRIGGER controls engine  
speed.  
THROTTLE LOCKOUT  
The THROTTLE LOCKOUT must be pressed  
before you can squeeze the throttle trigger.  
This feature prevents you from accidentally  
squeezing the trigger.  
CHAIN TENSION  
It is normal for a new chain to stretch during first  
30 minutes of operation. You should check  
your chain tension frequently. See CHAIN  
TENSION under the ASSEMBLY section.  
CHOKE/FAST IDLE LEVER  
The choke and fast idle are set by pulling the  
CHOKE/FAST IDLE LEVER out fully for cold  
or refueled starting. The choke provides addi-  
tional fuel to the engine during cold starting.  
WARNING: Muffler is very hot dur-  
ing and after use. Do not touch the muffler or  
allow combustible material such as dry  
grass or fuel to do so.  
PRIMER BULB  
The PRIMER BULB circulates fuel to the  
carburetor to provide quicker starting.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUELING & LUBRICATION  
STARTING  
WARNING: The chain must not  
move when the engine runs at idle speed. If  
the chain moves at idle speed refer to CAR-  
BURETOR ADJUSTMENT within this  
manual. Avoid contact with the muffler. A hot  
muffler can cause serious burns.  
To stop the engine move the ON/STOP  
switch to the STOP position.  
To start the engine hold the saw firmly on  
the ground as illustrated. Make sure the  
chain is free to turn without contacting any  
object.  
WARNING: Remove fuel cap slow-  
ly when refueling.  
FUELING ENGINE  
This engine is certified to operate on  
unleaded gasoline. Before operation,  
gasoline must be mixed with a good quality  
synthetic 2-cycle air-cooled engine oil  
designed to be mixed at a ratio of 40:1.  
Poulan/Weed Eater brand synthetic oil is  
recommended. Mix gasoline and oil at a ratio  
of 40:1. A 40:1 ratio is obtained by mixing 3.2  
ounces of oil with 1 gallon of unleaded  
gasoline. Included with this saw is a 3.2  
ounce container of oil. Pour the entire  
contents of this container into 1 gallon of  
gasoline to achieve the proper fuel mixture.  
DO NOT USE automotive oil or boat oil. These  
oils will cause engine damage. When mixing  
fuel, follow instructions printed on container.  
Once oil is added to gasoline, shake container  
momentarily to assure that the fuel is  
thoroughly mixed. Always read and follow the  
safety rules relating to fuel before fueling your  
unit.  
Use only 15---18” of rope per pull.  
Hold saw firmly while pulling starter rope  
Starter rope handle  
Left hand  
on front  
handle  
Right foot through rear handle  
BAR AND CHAIN LUBRICATION  
The bar and chain require continuous lubri-  
cation. Lubrication is provided by the auto-  
matic oiler system when the oil tank is kept  
filled. Lack of oil will quickly ruin the bar and  
chain. Too little oil will cause overheating  
shown by smoke coming from the chain and/  
or discoloration of the bar.  
In freezing weather oil will thicken, making it  
necessary to thin bar and chain oil with a  
small amount (5 to 10%) of #1 Diesel Fuel or  
kerosene. Bar and chain oil must be free  
flowing for the oil system to pump enough oil  
for adequate lubrication.  
IMPORTANT POINTS TO REMEMBER  
When pulling the starter rope, do not use the  
full extent of the rope as this can cause the  
rope to break. Do not let starter rope snap  
back. Hold the handle and let the rope rewind  
slowly.  
For cold weather starting, start the unit at  
FULL CHOKE; allow the engine to warm up  
before squeezing the throttle trigger.  
NOTE: Do not cut material with the choke/  
fast idle lever at the FULL CHOKE position.  
STARTING A COLD ENGINE (or  
warm engine after running out of  
fuel):  
Genuine Poulan or Poulan PROR bar and  
chain oil is recommended to protect your unit  
against excessive wear from heat and  
friction. Poulan or Poulan PROR oil resists  
high temperature thinning. If Poulan or  
NOTE: In the following steps, when the  
choke/fast idle lever is pulled out to the full  
extent, the correct throttle setting for starting  
is set automatically.  
Poulan PROR  
bar and chain oil is not  
available, use a good grade SAE 30 oil.  
S Never use waste oil for bar and chain lubri-  
1. Move ON/STOP switch to the ON posi-  
cation.  
tion.  
S Always stop the engine before removing  
2. Pull out choke/fast idle to the full extent.  
3. Slowly press primer bulb 6 times.  
4. Pull the starter rope quickly with your  
right hand 5 times. Then, proceed to the  
next step.  
the oil cap.  
IMPORTANT  
Experience indicates that alcohol--blended  
fuels (called gasohol or using ethanol or  
methanol) can attract moisture which leads  
to separation and formation of acids during  
storage. Acidic gas can damage the fuel  
system of an engine while in storage. To  
avoid engine problems, the fuel system  
should be emptied before storage for 30  
days or longer. Drain the gas tank, start the  
engine and let it run until the fuel lines and  
carburetor are empty. Use fresh fuel next  
season. See STORAGE section for addi-  
tional information.  
NOTE: If the engine sounds as if it is trying  
to start before the 5th pull, stop pulling and  
immediately proceed to the next step.  
5. Push the choke/fast idle lever in com-  
pletely (to the OFF position).  
6. Pull the starter rope quickly with your  
right hand until the engine starts.  
7. Allow the engine to run for approximately  
5 seconds. Then, squeeze and release  
throttle trigger to allow engine to return to  
idle speed.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
S If the brake is already activated, it is  
disengaged by pulling the front hand guard  
back toward the front handle as far as  
possible.  
S When cutting with the saw, the chain brake  
must be disengaged.  
ON/STOP  
Switch  
Primer  
Bulb  
Disengaged  
ON/STOP SWITCH  
ON  
STOP  
CHOKE/FAST IDLE LEVER  
(SIDE VIEW)  
Braking function control  
CAUTION: The chain brake must be  
checked several times daily. The engine  
must be running when performing this proce-  
dure. This is the only instance when the saw  
should be placed on the ground with the en-  
gine running.  
Place the saw on firm ground. Grip the rear  
handle with your right hand and the front han-  
dle with your left hand. Apply full throttle by  
fully depressing the throttle trigger. Activate  
the chain brake by turning your left wrist  
against the hand guard without releasing  
your grip around the front handle. The chain  
should stop immediately.  
Choke/Fast  
Idle Lever  
OFF FULL  
STARTING A WARM ENGINE:  
1. Move ON/STOP switch to the ON posi-  
tion.  
2. Pull the choke/fast idle lever out to the full  
extent, then push the lever back in com-  
pletely (to the OFF position).  
3. Slowly press the primer bulb 6 times.  
4. Pull the starter rope quickly with your  
right hand until the engine starts.  
5. Squeeze and release throttle trigger, al-  
lowing engine to idle.  
Inertia activating function control  
WARNING: When performing the  
following procedure, the engine must be  
turned off.  
DIFFICULT STARTING (or starting a  
flooded engine):  
Grip the rear handle with your right hand and  
the front handle with your left hand. Hold the  
chain saw approximately 14” (35 cm) above  
a stump or other wooden surface. Release  
your grip on the front handle and use the  
weight of the saw to let the top of the guide  
bar fall forward and contact the stump.  
When the tip of the bar hits the stump, the  
brake should activate.  
The engine may be flooded with too much  
fuel if it has not started after 10 pulls.  
Flooded engines can be cleared of excess  
fuel by following the warm engine starting  
procedure listed above. Insure the ON/  
STOP switch is in the ON position.  
Starting could require pulling the starter rope  
handle many times depending on how badly  
the unit is flooded. If engine fails to start, refer  
to the TROUBLESHOOTING TABLE or call  
1-800-554-6723.  
CUTTING METHODS  
CHAIN BRAKE  
IMPORTANT POINTS  
S Check chain tension before first use and  
after 1 minute of operation. See CHAIN  
TENSION in the ASSEMBLY section.  
S Cut wood only. Do not cut metal, plastics,  
masonry, non-wood building materials,  
etc.  
WARNING: If the brake band is  
worn too thin it may break when the chain  
brake is triggered. With a broken brake band,  
the chain brake will not stop the chain. The  
chain brake should be replaced by an autho-  
rized service dealer if any part is worn to less  
than 0.020! (0.5 mm) thick. Repairs on a  
chain brake should be made by an autho-  
rized service dealer. Take your unit to the  
place of purchase if purchased from a ser-  
vicing dealer, or to the nearest authorized  
master service dealer.  
S This saw is equipped with a chain brake.  
The brake is designed to stop the chain if  
kickback occurs.  
S The inertia--activated chain brake is  
activated if the front hand guard is pushed  
forward, either manually (by hand) or  
automatically (by sudden movement).  
S Stop the saw if the chain strikes a foreign  
object. Inspect the saw and repair or re-  
place parts as necessary.  
S Keep the chain out of dirt and sand. Even a  
small amount of dirt will quickly dull a chain  
and thus increase the possibility of kick-  
back.  
S Practice cutting a few small logs using the  
following techniques to get the “feel” of us-  
ing your saw before you begin a major  
sawing operation.  
S
Squeeze the throttle trigger and allow  
the engine to reach full speed before  
cutting.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S
S
S
Begin cutting with the saw frame  
against the log.  
FELLING LARGE TREES  
(6 inches in diameter or larger)  
Keep the engine at full speed the entire  
time you are cutting.  
The notch method is used to fell large trees.  
A notch is cut on the side of the tree in the de-  
sired direction of fall. After a felling cut is  
made on the opposite side of tree, the tree  
will tend to fall into the notch.  
NOTE: If the tree has large buttress roots,  
remove them before making the notch. If us-  
ing saw to remove buttress roots, keep saw  
chain from contacting ground to prevent dull-  
ing of the chain.  
Allow the chain to cut for you. Exert only  
light downward pressure. If you force  
the cut, damage to the bar, chain, or en-  
gine can result.  
S
S
Release the throttle trigger as soon as  
the cut is completed, allowing the en-  
gine to idle. If you run the saw at full  
throttle without a cutting load, unneces-  
sary wear can occur to the chain, bar,  
and engine.  
NOTCH CUT AND FELLING THE  
TREE  
To avoid losing control when cut is com-  
plete, do not put pressure on saw at end  
of cut.  
S Make notch cut by cutting the top of the  
notch first. Cut through 1/3 of the diameter  
of the tree. Next complete the notch by cut-  
ting the bottom of the notch. See illustra-  
tion. Once the notch is cut remove the  
notch of wood from the tree.  
S Stop the engine before setting the saw  
down after cutting.  
TREE FELLING TECHNIQUES  
WARNING: Check for broken or  
dead branches which can fall while cutting  
causing serious injury. Do not cut near build-  
ings or electrical wires if you do not know the  
direction of tree fall, nor cut at night since you  
will not be ale to see well, nor during bad  
weather such as rain, snow, or strong winds,  
etc.  
Final (felling) cut here. 2 inches  
above center of notch.  
First cut  
Notch  
S Carefully plan your sawing operation in ad-  
vance.  
S Clear the work area. You need a clear area  
all around the tree so you can have secure  
footing.  
Second cut  
Hinge  
S Study the natural conditions that can cause  
the tree to fall in a particular direction.  
Natural conditions that can cause a tree to  
fall in a particular direction include:  
S The wind direction and speed.  
S The lean of the tree. The lean of a tree  
might not be apparent due to uneven or  
sloping terrain. Use a plumb or level to de-  
termine the direction of tree lean.  
S Weight and branches on one side.  
S Surrounding trees and obstacles.  
Look for decay and ro.t If the trunk is rotted, it  
can snap and fall toward the operator. Check  
for broken or dead branches which can fall on  
you while cutting.  
S After removing the cutout of wood, make  
the felling cut on the opposite side of the  
notch. This is done by making a cut about  
two inches higher than the center of the  
notch. This will leave enough uncut wood  
between the felling cut and the notch to  
form a hinge. This hinge will help prevent  
the tree from falling in the wrong direction.  
Hinge holds tree on stump and helps  
control fall  
Opening  
of felling  
cut  
Make sure there is enough room for the tree to  
fall. Maintain a distance of 2-1/2 tree lengths  
from the nearest person or other objects. En-  
gine noise can drown out a warning call.  
Remove dirt, stones, loose bark, nails, staples,  
and wire from the tree where cuts are to be  
made.  
Plan a clear retreat path to the rear and diag-  
onal to the line of fall.  
Closing of  
notch  
NOTE: Before felling cut is complete, use  
wedges to open the cut when necessary to  
control the direction of fall. To avoid kickback  
and chain damage, use wood or plastic  
wedges, but never steel or iron wedges.  
S Be alert to signs that the tree is ready to fall:  
cracking sounds, widening of the felling cut,  
or movement in the upper branches.  
Plan a clear retreat path  
Direction of Fall  
45_  
S As tree starts to fall, stop saw, put it down,  
and get away quickly on your planned re-  
treat path.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S DO NOT cut down a partially fallen tree  
with your saw. Be extremely cautious with  
partially fallen trees that may be poorly  
supported. When a tree doesn’t fall com-  
pletely, set the saw aside and pull down the  
tree with a cable winch, block and tackle,  
or tractor.  
CUTTING A FALLEN TREE  
(BUCKING)  
Bucking is the term used for cutting a fallen  
tree to the desired log size.  
WARNING: Never turn saw upside  
down to undercut. The saw cannot be con-  
trolled in this position.  
Always make your first cut on the compres-  
sion side of the log. The compression side of  
the log is where the pressure of the log’s  
weight is concentrated.  
First cut on compression side of log  
WARNING: Do not stand on the log  
being cut. Any portion can roll causing loss  
of footing and control. Do not stand downhill  
of the log being cut.  
Second cut  
Second cut  
IMPORTANT POINTS  
S Cut only one log at a time.  
S Cut shattered wood very carefully; sharp  
pieces of wood could be flung toward oper-  
ator.  
S Use a sawhorse to cut small logs. Never  
allow another person to hold the log while  
cutting and never hold the log with your leg  
or foot.  
First cut on compression side of log  
S Do not cut in an area where logs, limbs,  
and roots are tangled such as in a blown  
down area. Drag the logs into a clear area  
before cutting by pulling out exposed and  
cleared logs first.  
BUCKING WITHOUT A  
SUPPORT  
S Overcut through 1/3 of the diameter of the  
log.  
S Roll the log over and finish with a second  
overcut.  
S Watch for logs with a compression side to  
prevent the saw from pinching. See il-  
lustration for cutting logs with a compres-  
sion side.  
TYPES OF CUTTING USED FOR  
BUCKING  
WARNING:  
If saw becomes  
pinched or hung in a log, don’t try to force it  
out. You can lose control of the saw resulting  
in injury and/or damage to the saw. Stop the  
saw, drive a wedge of plastic or wood into the  
cut until the saw can be removed easily. Re-  
start the saw and carefully reenter the cut. To  
avoid kickback and chain damage, do not  
use a metal wedge. Do not attempt to restart  
your saw when it is pinched or hung in a log.  
BUCKING USING A LOG OR  
SUPPORT STAND  
S Remember your first cut is always on the  
compression side of the log.  
(Refer to the illustration below for your first  
and second cut)  
S Your first cut should extend 1/3 of the  
diameter of the log.  
Use a wedge to remove pinched saw  
S Finish with your second cut.  
Using a log for support  
nd  
2
Cut  
Turn saw OFF and use a plastic or  
wooden wedge to force cut open.  
Overcutting begins on the top side of the log  
with the bottom of the saw against the log.  
When overcutting use light downward pres-  
sure.  
st  
1
Cut  
Overcutting  
Undercutting  
st  
1
Cut  
Undercutting involves cutting on the under-  
side of the log with top of saw against the log.  
When undercutting use light upward pres-  
sure. Hold saw firmly and maintain control.  
The saw will tend to push back toward you.  
nd  
2
Cut  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using a support stand  
PRUNING  
nd  
2
Cut  
WARNING: Limit pruning to limbs  
shoulder height or below. Do not cut if  
branches are higher than your shoulder. Get  
a professional to do the job.  
S
Make your fist cut 1/3 of the way  
through the bottom of the limb.  
Next make a 2nd cut all the way  
through the limb. Then cut a third  
overcut leaving a 1 to 2 inch collar from  
the truck of the tree.  
st  
1
Cut  
Cut  
S
st  
1
nd  
2
Cut  
Second cut  
Third cut  
LIMBING AND PRUNING  
Collar  
WARNING: Be alert for and guard  
against kickback. Do not allow the moving  
chain to contact any other branches or ob-  
jects at the nose of the guide bar when limb-  
ing or pruning. Allowing such contact can re-  
sult in serious injury.  
First cut  
Pruning technique  
SERVICE  
WARNING: Never climb into a tree  
to limb or prune. Do not stand on ladders,  
platforms, a log, or in any position which can  
cause you to lose your balance or control of  
the saw.  
WARNING: Disconnect the spark  
plug before performing maintenance except  
for carburetor adjustments.  
IMPORTANT POINTS  
We recommend all service and adjustments  
not listed in this manual be performed by an  
authorized service dealer.  
S Work slowly, keeping both hands firmly  
gripped on the saw. Maintain secure foot-  
ing and balance.  
S Watch out for springpoles. Springpoles  
are small size limbs which can catch the  
saw chain and whip toward you or pull you  
off balance. Use extreme caution when  
cutting small size limbs.  
S Be alert for springback. Watch out for  
branches that are bent or under pressure.  
Avoid being struck by the branch or the  
saw when the tension in the wood fibers is  
released.  
S Keep a clear work area. Frequently clear  
branches out of the way to avoid tripping  
over them.  
MAINTENANCE SCHEDULE  
Lubricate bar  
sprocket hole . . . . . . . After each use  
Check:  
Fuel mixture level . . . . Before each use  
Bar lubrication . . . . . . . Before each use  
Chain tension . . . . . . . Before each use  
Chain sharpness . . . . Before each use  
For damaged parts . . Before each use  
For loose caps . . . . . . Before each use  
For loose fasteners. . . Before each use  
For loose parts . . . . . . Before each use  
Inspect and Clean:  
LIMBING  
S Always limb a tree after it is cut down. Only  
then can limbing be done safely and prop-  
erly.  
Bar . . . . . . . . . . . . . . . . Before each use  
Complete saw. . . . . . . After each use  
Air filter . . . . . . . . . . . . . Every 5 hours*  
Chain brake . . . . . . . . Every 5 hours*  
Spark arrestor screen  
S Leave the larger limbs underneath the  
felled tree to support the tree as you work.  
S Start at the base of the felled tree and work  
toward the top, cutting branches and  
limbs. Remove small limbs with one cut.  
S Keep the tree between you and the chain.  
Cut from the side of the tree opposite the  
branch you are cutting.  
and muffler . . . . . . . . . Every 25 hours*  
Replace spark plug . Yearly  
Replace fuel filter . . . Yearly  
* Hours of Operation  
S Remove larger, supporting branches with  
the cutting techniques described in BUCK-  
ING WITHOUT A SUPPORT.  
S Always use an overcut to cut small and  
freely hanging limbs. Undercutting could  
cause limbs to fall and pinch the saw.  
AIR FILTER  
CAUTION: Do not clean filter in gasoline  
or other flammable solvent to avoid creating  
a fire hazard or producing harmful evapora-  
tive emissions.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Reinstall muffler cover and 2 screws.  
Tighten securely.  
Cleaning the air filter:  
A dirty air filter decreases engine perform-  
ance and increases fuel consumption and  
harmful emissions. Always clean after 15  
tanks of fuel or 5 hours of operation, which-  
ever comes first. Clean more frequently in  
dusty conditions. A used aire filter can never  
be completely cleaned. It is advisable to re-  
place your air filter with a new one after every  
50 hours of operation, or annually, whichever  
comes first.  
CARBURETOR ADJUSTMENTS  
Your carburetor is equipped with limiter caps.  
Carburetor adjustment is a complicated task.  
We recommend that you take your unit to an  
authorized service dealer. Damage will occur if  
you turn the needles beyond the limiter stops.  
BAR MAINTENANCE  
If your saw cuts to one side, has to be forced  
through the cut, or been run with an improper  
amount of bar lubrication it may be necessary  
to service your bar. A worn bar will damage  
your chain and make cutting difficult.  
After each use, ensure ON/STOP switch is in  
the STOP position, then clean all sawdust from  
the guide bar and sprocket hole.  
To maintain guide bar:  
1. Loosen 3 screws on cylinder cover.  
2. Remove cylinder cover.  
3. Remove air filter.  
4. Clean the air filter using hot soapy water.  
Rinse with clean cool water. Air dry com-  
pletely before reinstalling.  
5. Lightly oil air filter before installing to im-  
prove the efficiency of air filter. Use  
2--cycle engine oil or motor oil (SAE 30).  
Squeeze excess oil from filter.  
S Move ON/STOP switch to the STOP posi-  
tion.  
S Loosen and remove chain brake nuts and  
chain brake. Remove bar and chain from  
saw.  
6. Reinstall air filter.  
7. Reinstall cylinder cover and 3 screws.  
TIghten securely.  
S Clean the oil holes and bar groove after each  
5 hours of operation.  
Cylinder  
Air
over  
crews  
Remove Sawdust From  
Guide Bar Groove  
ylinder  
over  
Oil Holes  
INSPECT MUFFLER AND SPARK  
ARRESTING SCREEN  
S Burring of guide bar rails is a normal process  
of rail wear. Remove these burrs with a flat  
file.  
As the unit is used, carbon deposits build up  
on the muffler and spark arresting screen,  
and must be removed to avoid creating a fire  
hazard or affecting engine performance.  
Replace the spark arresting screen if breaks  
occur.  
S When rail top is uneven, use a flat file to re-  
store square edges and sides.  
File Rail Edges  
and Sides  
Square  
Spark  
Worn Groove  
Correct Groove  
Arresting  
Screen  
Replace guide bar when the groove is worn,  
the guide bar is bent or cracked, or when exce-  
ss heating or burring of the rails occurs. If re-  
placement is necessary, use only the guide bar  
specified for your saw in the repair parts list or  
on the decal located on the chain saw.  
r  
s  
CHAIN SHARPENING  
Chain sharpening is a complicated task that  
requires special tools. We recommended  
you refer chain sharpening to a professional  
chain sharpener.  
Cleaning is required every 25 hours of opera-  
tion or annually, whichever comes first.  
1. Loosen and remove the 2 muffler cover  
screws.  
IGNITION TIMING  
Ignition timing is fixed and nonadjustable.  
SPARK PLUG  
The spark plug should be replaced each  
year to ensure the engine starts easier and  
runs better.  
1. Loosen 3 screws on cylinder cover.  
2. Remove the cylinder cover.  
3. Pull off the spark plug boot.  
4. Remove spark plug from cylinder and dis-  
card.  
5. Replace with Champion RCJ--7Y spark  
plug and tighten securely with a 3/4 inch  
2. Remove the muffler cover (cover snaps off  
muffler body).  
3. Remove muffler diffuser and spark arrest-  
ing screen assembly. Notice the orientation  
of these parts for reassembling.  
4. Clean the spark arrestor screen with a wire  
brush. Replace screen if breaks are found.  
5. Replace any broken or cracked muffler  
parts.  
6. Reinstall diffuser and spark arrestor screen  
assembly with round holes facing up.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
socket wrench. Spark plug gap should  
be 0.025 inches.  
Start engine and allow to run until it stops.  
S Clean the unit before storing. Pay particu-  
lar attention to the air intake area, keeping  
it free of debris. Use a mild detergent and  
sponge to clean the plastic surfaces.  
S Do not store the unit or fuel in a closed area  
where fuel vapors can reach sparks or an  
open flame from hot water heaters, electric  
motors or switches, furnaces, etc.  
6. Reinstall the spark plug boot.  
7. Reinstall the cylinder cover and 3 screws.  
Tighten securely.  
Cylinder  
Cover  
Screws  
Spark  
Plug Boot  
S Store in a dry area out of the reach of chil-  
dren.  
CAUTION: It is important to prevent gum  
deposits from forming in essential fuel system  
parts such as the carburetor, fuel filter, fuel  
hose, or fuel tank during storage. Alcohol  
blended fuels (called gasohol or using ethanol  
or methanol) can attract moisture which leads  
to fuel mixture separation and formation of  
acids during storage. Acidic gas can damage  
the engine.  
Spark  
Plug  
STORAGE  
WARNING: Stop engine and allow  
to cool, and secure the unit before storing or  
transporting in a vehicle. Store unit and fuel  
in an area where fuel vapors cannot reach  
sparks or open flames from water heaters,  
electric motors or switches, furnaces, etc.  
Store unit with all guards in place. Position so  
that any sharp object cannot accidentally  
cause injury to passersby. Store the unit out  
of reach of children.  
NEED ASSISTANCE?  
NEED ASSISTANCE?  
Call 1--800--554--6723.  
NEED SERVICE PART?  
S Before storing, drain all fuel from the unit.  
Contact your authorized service dealer.  
TROUBLESHOOTING TABLE  
WARNING: Always stop unit and disconnect spark plug before performing all of  
the recommended remedies below except remedies that require operation of the unit.  
TROUBLE  
CAUSE  
REMEDY  
Engine will not  
start or will run  
only a few  
seconds after  
starting.  
1. Move ignition switch to ON.  
2. See “Difficult Starting” in  
Operation Section.  
1. Ignition switch off.  
2. Engine flooded.  
3. Fill tank with correct fuel mixture.  
4. Install new spark plug.  
3. Fuel tank empty.  
3. Spark plug not firing.  
4. Fuel not reaching  
carburetor.  
5. Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
Engine will  
not idle  
properly.  
1. Carburetor requires  
adjustment  
2. Crankshaft seals worn.  
1. Contact an authorized service dealer.  
2. Contact an authorized service dealer.  
1. Clean or replace air filter.  
1. Air filter dirty.  
Engine will not  
accelerate,  
lacks power,  
or dies under  
a load.  
2. Clean or replace plug and regap.  
3. Disengage chain brake.  
2. Spark plug fouled.  
3. Chain brake engaged.  
4. Carburetor requires  
adjustment.  
4. Contact an authorized service dealer.  
1. Too much oil mixed with 1. Empty fuel tank and refill with  
gasoline. correct fuel mixture.  
Engine  
smokes  
excessively.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
ELECTROLUX HOME PRODUCTS, INC.,  
ty does not cover predelivery set--up, instal-  
lation of guide bar and chain, and normal ad-  
justments explained in the instruction  
manual such as carburetor adjustments and  
chain tension adjustments. This warranty  
does not cover transportation costs.  
THIS WARRANTY GIVES YOU SPECIFIC  
LEGAL RIGHTS, AND YOU MAY HAVE  
OTHER RIGHTS WHICH VARY FROM  
STATE TO STATE.  
NO CLAIMS FOR CONSEQUENTIAL OR  
OTHER DAMAGES WILL BE ALLOWED,  
AND THERE ARE NO OTHER EXPRESS  
WARRANTIES EXCEPT THOSE EXPRESS-  
LY STIPULATED HEREIN.  
warrants to the original purchaser that each  
new Poulan PRO brand gasoline chain saw  
is free from defects in material and workman-  
ship and agrees to repair or replace under  
this warranty any defective gasoline chain  
saw as follows from the original date of pur-  
chase.  
2 YEARS -- Parts and Labor, when used for  
Household purposes.  
60 DAYS -- Parts and Labor, when used for  
Commercial, Professional, or Income Pro-  
ducing purposes.  
30 DAYS -- Parts and Labor, if used for rental  
purposes.  
This warranty is not transferable and does  
not cover damage or liability caused by im-  
proper handling, improper maintenance, or  
the use of accessories and/or attachments  
not specifically recommended by ELEC-  
TROLUX HOME PRODUCTS, INC., for this  
chain saw. Additionally, this warranty does  
not cover damage caused by improper han-  
dling, improper maintenance, or if the saw is  
altered in any way which in our judgement af-  
fects its condition or operation. This warranty  
does not cover tune--up, spark plugs, filters,  
starter ropes, starter springs, chain sharpen-  
ing, bars, chains, and other parts which wear  
and require replacement with reasonable  
use during the warranty period. This warran-  
SOME STATES DO NOT ALLOW LIMITA-  
TIONS ON HOW LONG AN IMPLIED WAR-  
RANTY LASTS OR THE EXCLUSION OR  
LIMITATIONS OF INCIDENTAL OR CONSE-  
QUENTIAL DAMAGES, SO THE ABOVE  
LIMITATIONS OR EXCLUSION MAY NOT  
APPLY TO YOU.  
The policy of ELECTROLUX HOME PROD-  
UCTS, INC., is to continuously improve its  
products. Therefore, ELECTROLUX HOME  
PRODUCTS, INC., reserves the right to  
change, modify, or discontinue models, de-  
signs, specifications, and accessories of all  
products at any time without notice or obliga-  
tion to any purchaser.  
U.S. EPA / ENVIRONMENT CANADA  
EMISSION CONTROL WARRANTY STATEMENT  
YOUR WARRANTY RIGHTS AND OBLIGA-  
TIONS: The U. S. Environmental Protection  
Agency, Environment Canada and POU-  
LAN/WEED EATER, DIVISION OF WCI  
OUTDOOR PRODUCTS, INC., are pleased  
to explain the emissions control system war-  
ranty on your year 2001--2004 small off--road  
engine. POULAN/WEED EATER must war-  
rant the emission control system on your small  
off--road engine for the periods of time listed be-  
low provided there has been no abuse, ne-  
glect, or improper maintenance of your small  
off--road engine. Your emission control system  
includes parts such as the carburetor and the  
ignition system. Where a warrantable condition  
exists, POULAN/WEED EATER will repair  
your small off--road engine at no cost to you.  
Expenses covered under warranty include  
diagnosis, parts and labor. MANUFACTUR-  
ER’S WARRANTY COVERAGE: If any emis-  
sions related part on your engine (as listed un-  
der Emissions Control Warranty Parts List) is  
defective or a defect in the materials or work-  
manship of the engine causes the failure of  
such an emission related part, the part will be  
repaired or replaced by POULAN/WEED EAT-  
ER. OWNER’S WARRANTY RESPONSI-  
BILITIES: As the small off--road engine owner,  
you are responsible for the performance of the  
required maintenance listed in your instruction  
manual. POULAN/WEED EATER recom-  
mends that you retain all receipts covering  
maintenance on your small off--road engine,  
but POULAN/WEED EATER cannot deny  
warranty solely for the lack of receipts or for  
your failure to ensure the performance of all  
scheduled maintenance. As the small off--  
road engine owner, you should be aware that  
POULAN/WEED EATER may deny you war-  
ranty coverage if your small off--road engine or  
a part of it has failed due to abuse, neglect, im-  
proper maintenance, unapproved modifica-  
tions, or the use of parts not made or approved  
by the original equipment manufacturer. You  
are responsible for presenting your small off--  
road engine to a POULAN/WEED EATER au-  
thorized repair center as soon as a problem ex-  
ists. Warranty repairs should be completed in a  
reasonable amount of time, not to exceed 30  
days. If you have any questions regarding your  
warranty rights and responsibilities, you should  
contact your nearest authorized service center  
or call POULAN/WEED EATER at  
1--800--554--6723.  
WARRANTY COM-  
MENCEMENT DATE: The warranty period  
begins on the date the small off--road engine is  
purchased. LENGTH OF COVERAGE: This  
warranty shall be for a period of two years from  
the initial date of purchase. WHAT IS COV-  
ERED: REPAIR OR REPLACEMENT OF  
PARTS. Repair or replacement of any war-  
ranted part will be performed at no charge to  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
the owner at an approved POULAN/WEED  
EATER servicing center. If you have any ques-  
tions regarding your warranty rights and re-  
sponsibilities, you should contact your nearest  
authorized service center or call POULAN/  
WEED EATER at 1--800--554--6723. WAR-  
RANTY PERIOD: Any warranted part which is  
not scheduled for replacement as required  
maintenance, or which is scheduled only for  
regular inspection to the effect of ”repair or re-  
place as necessary” shall be warranted for 2  
years. Any warranted part which is scheduled  
for replacement as required maintenance shall  
be warranted for the period of time up to the first  
scheduled replacement point for that part.  
DIAGNOSIS: The owner shall not be charged  
for diagnostic labor which leads to the deter-  
mination that a warranted part is defective if the  
diagnostic work is performed at an approved  
POULAN/WEED EATER servicing center.  
CONSEQUENTIAL DAMAGES: POULAN/  
WEED EATER may be liable for damages to  
other engine components caused by the failure  
of a warranted part still under warranty. WHAT  
IS NOT COVERED: All failures caused by  
abuse, neglect, or improper maintenance are  
not covered. ADD--ON OR MODIFIED  
PARTS: The use of add--on or modified parts  
can be grounds for disallowing a warranty  
claim. POULAN/WEED EATER is not liable to  
cover failures of warranted parts caused by the  
use of add--on or modified parts. HOW TO  
FILE A CLAIM: If you have any questions re-  
garding your warranty rights and responsibili-  
ties, you should contact your nearest autho-  
rized service center or call POULAN/WEED  
EATER at 1--800--554--6723. WHERE TO  
GET WARRANTY SERVICE: Warranty ser-  
vices or repairs shall be provided at all POU-  
LAN/WEED EATER service centers. Call  
1--800--554--6723. MAINTENANCE, RE-  
PLACEMENT AND REPAIR OF EMISSION  
RELATED PARTS: Any POULAN/WEED  
EATER approved replacement part used in the  
performance of any warranty maintenance or  
repair on emission related parts will be pro-  
vided without charge to the owner if the part is  
under warranty.  
EMISSION CONTROL  
WARRANTY PARTS LIST: Carburetor, Igni-  
tion System: Spark Plug (covered up to main-  
tenance schedule), Ignition Module. MAINTE-  
NANCE STATEMENT: The owner is  
responsible for the performance of all required  
maintenance as defined in the instruction  
manual.  
The information on the product label indicates which standard your engine is certified.  
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.  
This engine is certified to be emissions compliant for the following use:  
Moderate (50 hours)  
Intermediate (125 hours)  
Extended (300 hours)  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips Baby Monitor SCD505 User Manual
Philips Computer Monitor VSS9451 User Manual
Philips Portable DVD Player PET704 98 User Manual
Philips TV VCR Combo 14PV345 User Manual
Pioneer Flat Panel Television KRP 500A User Manual
Pioneer Stereo System VSX 84TXSI User Manual
Polaroid Digital Camera IS2132 BLACK User Manual
Polycom Network Router 3726 17298 001 User Manual
Poulan Snow Blower PR524ESA User Manual
ProForm Treadmill PFTL999080 User Manual