Note: Rockler may not carry all products and/or sizes listed in this vendor's publication
INSTRUCTION
ESPAÑOL: PÁGINA 27
FRANÇAISE : PAGE 51
MANUAL
DOVETAIL JIG
MODELS 4210 & 4212
(29550)
IMPORTANT
To learn more about Porter-Cable
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
visit our website at:
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. _____________________________________
Type __________________________________________
Serial No.______________________________________
Copyright © 2004 Porter-Cable Corporation
RTD10000210AA
Part No. A05065 - 05-27-05
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY GUIDELINES - DEFINITIONS
This manual contains information that is important for you to know and understand. This information relates to pro-
tecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use
the symbols to the left. Please read the manual and pay attention to these sections.
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may
result in property damage.
IMPORTANT SAFETY INSTRUCTIONS
Read and understand all instructions. Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS.
There are certain applications for which this tool was designed. Porter-Cable strongly recommends that this
tool NOT be modified and/or used for any application other than for which it was designed. If you have any questions relative to
its application DO NOT use the tool until you have written Porter-Cable and we have advised you.
Technical Service Manager
Porter-Cable Corporation
4825 Highway 45 North
Jackson, TN 38305
1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
2. AVOID DANGEROUS ENVIRONMENT. Don’t expose power tools to rain. Don’t use power tools in damp or wet
locations. Keep area well lit. Avoid chemical or corrosive environment. Do not use tool in presence of flammable
liquids or gases.
3. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example: pipes,
radiators, ranges, refrigerator enclosures.
4. KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors should be kept away from
work area.
5. STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-up place – out of reach
of children.
6. DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was intended.
7. USE RIGHT TOOL. Don’t force small tool or attachment to do the job of a heavy duty tool. Don’t use tool for
purpose not intended – for example – do not use a circular saw for cutting tree limbs or logs.
8. DRESS PROPERLY. Do not wear loose clothing or jewelry. Loose clothing, draw strings and jewelry can be
caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear
protective hair covering to contain long hair.
9. USE ANSI Z87.1 SAFETY GLASSES. Wear safety glasses or goggles while operating power tools. Also face or
dust mask if operation creates dust. All persons in the area where power tools are being operated should also
wear safety glasses and face or dust mask.
10. DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat,
oil, and sharp edges. Have damaged or worn power cord and strain reliever replaced immediately. DO NOT
ATTEMPT TO REPAIR POWER CORD.
11. SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to
operate tool.
12. DON’T OVERREACH. Keep proper footing and balance at all times.
13. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have
repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Have all
worn, broken or lost parts replaced immediately. Keep handles dry, clean and free from oil and grease.
14. DISCONNECT TOOLS when not in use, before servicing, and when changing accessories such as blades, bits, cutters,
etc.
15. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning it on.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
16. AVOID UNINTENTIONAL STARTING. Do not carry a plugged-in tool with finger on switch. Be sure switch is off
when plugging in. Keep hands, body and clothing clear of blades, bits, cutters, etc. when plugging in the tool.
17. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords marked “Suitable
for use with outdoor appliances – store indoors when not in use.” If an extension cord is to be used outdoors it
must be marked with the suffix W-A or w following the cord type designation.
18. STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired or while
under the influence of medication, alcohol or drugs.
19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect
its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced
by authorized service center. Do not use tool if switch does not turn it on and off.
20. WEAR ANSI S3.19 EAR PROTECTION to safeguard against possible hearing loss.
ADDITIONAL SAFETY RULES
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS in the instruction manual supplied with your router.
2. SECURE WORK. Be sure Dovetail Fixture/Jig and work is anchored securely to prevent movement.
3. BE SURE CORD SET IS FREE and will not hang up during routing operations.
4. KEEP HANDS CLEAR of cutter when motor is running to prevent personal injury.
5. MAINTAIN FIRM GRIP on router when starting motor to resist starting torque.
6. STAY ALERT and keep cutter free, clear of all foreign objects while motor is running.
7. BE SURE MOTOR HAS COMPLETELY STOPPED before removing router from Dovetail Fixture/Jig and setting
Dovetail Fixture/Jig down between operations.
8. NEVER REMOVE ROUTER MOTOR from router base while template guide and dovetail bit are installed. dovetail
bit may not fit through hole in template guide.
9. TIGHTEN TEMPLATE GUIDE LOCKNUT SECURELY.
10. SOME WOOD CONTAINS PRESERVATIVES WHICH CAN BE TOXIC. Take extra care to prevent inhalation and
skin contact when working with these materials. Request, and follow, any safety information available from your
material supplier.
REPLACEMENT PARTS
When servicing use only identical replacement parts.
BACKGROUND INFORMATION
DOVETAIL AND BOX JOINT OVERVIEW
The dovetail joint is a traditional joint that is both strong and visually appealing. This joint has flared protrusions (tails)
that are cut into one board (drawer side) and protrusions with slanted sides (pins) that are cut in the other board
(drawer front or back). When the two pieces are joined, the tails and pins lock together mechanically, so that pulling
on the drawer front will pull the drawer side as well without the need for fasteners (screws, nails, etc.). Since the pins
and tails have a sufficient amount of surface, the joint is even made stronger by glue.
Types of dovetails include through dovetails, half-blind dovetails, rabbeted half-blind dovetails, mitered-through
dovetails, blind dovetails, and mitered dovetails. Of these joints, the through, half-blind, and rabbeted half-blind are
the most common.
NOTE: This manual includes instruction for the basic dovetail jig operations. Please visit our Web Site at
www.porter-cable.com/jigs for the supplementary manual that gives instruction for more advanced procedures.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
THROUGH DOVETAILS
Tails
Pins
HALF-BLIND DOVETAILS
RABBETED HALF-BLIND DOVETAILS
BOX (FINGER) JOINT
A similar joint, called a box or finger joint, has
straight protrusions called fingers on both boards.
This joint is used on jewelry boxes and other small
boxes. The box joint is strong because it has a large
surface area for glue.
DOVETAIL DADO (SLIDING DOVETAIL)
Tenon
The Dovetail Dado, or Sliding Dovetail,
consists of a dovetail-shaped dado in one
board and a dovetail-shaped tenon in the
other board. This method is a strong way of
connecting fixed shelves to walls.
Dado
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT CAPABILITIES
The Porter-Cable 4200 series dovetail jig will help you cut these joints efficiently. An accessory kit will enable you to
cut miniature versions of these joints for small gift boxes or cubbyhole drawers on a roll-top desk. The 4200 series
also has the capability to cut more advanced joints (dovetails that skip pins, wood hinges, end-to-end joints, various
types of angle joints, and joints with inlays).
The specific model capabilities are:
Jigs
4210 Dovetail Jig - half-blind, half-blind with a lipped front, and dovetail dados.
4212 Deluxe Dovetail Jig - through dovetail, box joint, half-blind, half-blind with a lipped front, and
dovetail dados.
Accessories
4211 Accessory Kit - includes the template, router bit, and templet guide included with the model 4210.
4213 Accessory kit - incudes all items necessary to provide the 4210 jig with the same capabilities as the
4212 deluxe dovetail jig.
4215 Accessory kit - contains the template, router bits, and templet guides to make miniature through
dovetails and half-blind dovetails.
JIG OVERVIEW
The 4200 series dovetail jigs come equipped with an easy-to-mount, heavy-duty steel base (A) Fig. A1 featuring a
clamping system designed to hold wood and minimize board slippage during cuts. Troubleshooting tips (B) are
provided on each side of the base. Three different machined aluminum templates (Fig. A2) can be used on the jig
system to create all joints described in this manual. The fingers on each template are used in combination with the
template guides (Fig. A3) to guide the router in the proper motion. Additionally, each template aids in setting proper
board alignment and router bit depth. Dovetail bits and straight bits (Figs. A4 and A5) are used with this jig system.
B
A
A3
A1
A2
A5
A4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CARTON CONTENTS
DOVETAIL JIGS
4210
4212
3
2
2
1
1
4
6
3
5
4
5
6
7
8
1. Base
1. Base
2. Half-blind & Dado Template
3. Through & Box Template
4. Dovetail Bit
2. Half-blind & Dado Template
3. Dovetail Bit
4. Template Guide
5. Lock nut
6. T-handle Hex Wrench
5. Straight Bit
6. Template Guide (2)
7. Lock Nuts (2)
8. T-handle Hex Wrench
ACCESSORY KITS
4211
4213
4215
1
1
1
5
4
3
2
5
4
3
7
2
5
4
3
2
10
6
6
6
8
7
7
8
10
11
9
9
9
8
1.
2.
3.
4.
5.
6.
7.
8.
9.
Half-blind & Dado Template
Brackets (2)
1.
Through and Box Joint
Template
1. Miniature Half-blind, Through, &
Box Template
Dado Depth Bracket
Half-blind Depth Bracket
Dovetail Bit
2.
3.
4.
5.
6.
7.
8.
Brackets (2)
2. Brackets (2)
Half-Blind Depth Bracket
Straight Bit
3. Template Guide and Lock Nut (2)
4. Half-blind Depth Bracket
5. Offset Guide (2)
6. Depth Knob
Depth Knob
Template Guide and Lock Nut
Hex Nuts (1)
Screws (8)
Hex Nuts (1)
Screws (6)
7. Dovetail Bit
Wrench
Depth Knob
8. Straight Bit
10. Template Guide and Lock Nut 9.
Wrench
9. Hex Nuts (1)
10.Screws (6)
11.Wrench
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
The 4200 series dovetail jigs come fully assembled from the factory. However, the accessory templates (4211, 4213,
4215) require assembly. The supplied hex wrench can be used to attach the brackets and router bit depth guides
to the template. A 3/8" wrench is required to adjust the height of the router bit depth guide.
3/8"
ASSEMBLED JIG
HEIGHT ADJUSTMENT
ADDITIONAL TOOLS REQUIRED
The router that you use with this jig
ꢀ
ꢀ
ꢀ
must accept the Porter-Cable template guides supplied with the
jig. (Adapters and sub-bases are available for most routers.)
must have a 1/2" collet for use with 4210 and 4212 jigs and the
4211 and 4213 accessory kits.
must have a 1/4" collet for use with the 4215 accessory kit.
NOTE: While the jigs and accessory kits include the router bits and template guides to make the basic dovetail
joints, additional router bits are required to make box joints.
MOUNTING INSTRUCTIONS
NOTE: Always mount your jig to a solid work surface.
You can mount your jig permanently (Fig. B1) by using the pre-drilled holes (A) Fig B1) on each side of the base, or
you can mount the base to your work surface using clamps (Fig. B2).
A
B1
B2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Mount your workpiece in the jig properly. If the workpiece is not secure, it can be damaged when it moves.
The jigs utilize two mounting positions for workpieces - horizontal and vertical. Some joints require both, while
others require the use of a scrap board in the horizontal position (upper clamp) and the workpiece in the vertical
position (lower clamp).
Position your workpiece correctly left-to-right to produce symmetrical and tight-fitting joints.
Tear-out from the router bit can be reduced when scrap wood is positioned properly against the workpiece.
CLAMPS
The 4200 series jigs are equipped with two cam-action clamps (A) Fig. C1 with knobs (B) to adjust for workpiece
thickness, and levers (C) for quick clamping and releasing of workpieces.
NOTE: Use a scrap board (A) Fig. C2 to prevent misalignment (A) Fig. C3.
C
A
A
A
B
A
C1
C2
C3
TEMPLATE MOUNTING
You can mount the templates in two positions on the jig(s) which allows the production of multiple types of joints
with each template. To reverse a template, loosen the template knobs (C) Fig. D1, remove the template (B) from the
base, rotate it 180 degrees horizontally, replace it on the base, and tighten the template knobs.
NOTE: Secure the templates by inserting the template brackets (A) Fig. D2 between the large template knobs (B)
Fig. D2 and the brass adjustment knobs (C). You can then make front-to-back adjustments by loosening the large
template knobs (B) and rotating the brass adjustment knobs (C).
B
ROTATE
A
C
C
D1
D2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TEMPLATE SUPPORT
For every type of joint, place wood in the top clamp, whether a workpiece or a scrap piece, to provide support for
the router on the template. You can add extra support by inserting a second board (A) Fig. E1 (of the same
thickness) in the top clamp to ensure that the template is parallel to the base across its length. This practice works
very well for narrow workpieces.
A
E1
E2
Supported
Unsupported
POSITIONING THE WOOD
You must position the workpiece correctly to produce attractive symmetrical joints. Use the offset guides to
consistently position the workpiece for optimal alignment and symmetry.
Step 1 -
Clamp the workpiece (or spacer board) (A) Fig. F1 in the horizontal position. The position is not critical, but
the workpiece must not extend beyond the front edge of the base.
Step 2 -
Mount the template (Fig. F2) on top of the horizontal workpiece. Press down on the template (A) with one
hand, and tighten the template knobs with the other.
Step 3 -
Loosen the left offset guide (A) Fig. F3 with the T-handle hex wrench (B) and move it to the far left position.
Step 4 -
Align the vertical workpiece (A) Fig. F4 flush against the bottom side of the template. Center and clamp the
workpiece between the farthest finger to the left and the nearest finger to the right of the template.
Step 5 -
Move the left offset guide (A) Fig. F5 to the right so that it is flush against the vertical workpiece (B). Tighten
the left offset guide with the T-handle wrench (C).
Step 6 -
Unclamp the horizontal workpiece and slide it forward so that it is flush against the vertical workpiece and
flush against the left offset guide (Fig. F6).
NOTE: The template has been removed for clarity.
A
A
B
F2
F1
F3
A
C
B
CENTER
A
F4
F5
F6
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HALF-PINS VS. HALF-TAILS
Traditionally, dovetails have half-pins cut on both ends (Fig. G1). Half-tails will be just as strong, but will not be as
attractive (Fig. G2). If your joints are half-tails and you want half-pins, move the vertical board 1/2" either left or right,
then move the horizontal board accordingly. The procedure is the same with the 4215 Miniature template, except
that you move the boards 1/4".
G1
G2
TEAROUT REDUCTION
Tearout is unwanted splintering of the wood fibers that occurs when a router bit enters, exits, or skims the edge of
wood and is common to all dovetail jigs. Tearout cannot be eliminated, but it can be reduced by the insertion of
additional scrap wood against the workpiece.
ALIGNING THE TEMPLATES
For proper operation, you must align the templates correctly from front to back. The 4200 series jigs have patented
alignment lines to help you align the templates without measuring. Some templates have one line (Fig. H1) while
others have several lines to produce multiple types of joints (Fig. H2). Porter-Cable has scribed icons on the
templates to indicate which lines go with which joints.
H2
H1
Adjust the templates front-to-back until the alignment line is directly over the point where the horizontal board and
the vertical board meet.
NOTE: To be accurate, lean over the template and look straight down to align the lines (Fig. H3).
For the joint to be produced correctly, loosen the knobs on both sides of the template, align the lines, hold the
template flat with one hand, and tighten the knobs with the other (Fig. H4).
NOTE: To help align both ends of the template when you are using a narrow workpiece, mount an additional piece
of wood (of the same thickness) on the far right (A) Fig. H5.
A
H3
H4
H5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TEMPLATE GUIDES
Use the correct template guides provided with this unit to
guide the router against the template fingers. To
determine the proper guide for a given joint, place the
template guide in the slot on the left side of the
corresponding template. The guide should have a snug fit
in the slot.
J1
ROUTER BIT DEPTH
DISCONNECT THE ROUTER FROM THE POWER SOURCE BEFORE MAKING ANY CHANGES
OR ADJUSTMENTS!
The depth-of-cut for the router bits is critical for a good-fitting joint. The 4200 series jigs have patented router bit
depth guides that allow the user to quickly and easily set the bit to the correct depth without measuring.
Rest the router on the left side of the template and gently lower the router bit until it touches the guide. Multiple
depth guides are provided on the jig because different joints require different depth settings.
NOTE: Attach the templet guide (with the lock nut) and the bit to your router using the instructions in your router’s
operating manual.
Step 1 -
Step 2 -
Lower the bit just past the edge of the templet guide (Fig. K1).
Use the slot with the corresponding scribed text on the template that matches the joint you will cut
(Fig. K2).
Step 3 -
Step 4 -
Place the router on the template with the guide and bit in the selected slot (Fig. K3).
Lower the router bit (A) Fig. K4 on the depth guide (B) and lock the position on your router.
Tails/Box Depth
Half-Blind Depth
K1
K2
A
B
K3
K4
12
Download from Www.Somanuals.com. All Manuals Search And Download.
WOOD PREPARATION
Properly preparing the materials for your project is the
key to good-looking and tight-fitting joints. You must cut
your wood at perfect right angles (Fig. L1). Cuts that are
off even one degree will not align correctly (Fig. L2). Also,
your workpieces must be flat and not cupped.
L2
L1
Orient your wood so that end grain is joined to end grain
(Fig. L3) to make the joint strong. Using the long grain
(Fig. L4) in the workpiece will result in a weak joint.
L4
L3
BOARD THICKNESS
NOTE: You can join two workpieces that are different thicknesses (Fig. M1).
The clamps on the 4200 series jigs will hold wood from 1/4" to 1-1/8"
thick. Use the following information as a guide to help you decide the
thickness of wood for your projects.
M1
Standard through dovetails
Tail Board Range
Pin Board Range
1/4" to 1"
1/4" to 3/4"
Miniature through dovetails
Half-blind dovetails
Both Tails and Pins
Standard and Miniature
1/4" to 1/2"
1/2" to 1-1/8"
Half-blind dovetail with a lipped front (Pin board will change depending
on the size of the lip).
Standard Box Joints (Limited by router bit length)
Miniature Box Joints
1/2" to 1-1/8"
1/4" to 1-1/8"
1/4" to 1/2"
Dovetail Dados
1/4" to 1-1/8"
OPTIMAL BOARD WIDTHS
The 4200 series dovetail jigs are capable of making joints up to 12". However, some widths will produce a more
attractive joint than others. The optimal widths for creating dovetails are in 1" increments plus 1/4" (1-1/4", 2-1/4",
3-1/4", etc.). Other widths will work, but will not be as attractive.
NOTE: If you are using the 4215 miniature accessory kit, the optimal widths are in 1/2" increments plus 1/8" (5/8",
1-1/8", 1-5/8", etc.).
BOARD LENGTHS
For through dovetails and box joints, cut your workpieces to the same length as the outside dimension of your final
project. However, cut the drawer sides (tail board) of half-blind joints as indicated below because the wood does
not go all the way through the joint.
To calculate the length of the half-blind tail board, take the inside dimension of the final project and add the router
bit depth of cut. If the tail board has a half-blind on both ends, double the added dimension. The length of the pin
boards (drawer front) remains the same.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PROJECT LAY OUT
Keeping track of the outer and inner face of each workpiece and how the different parts mate with each other is
very important.
Step 1 -
Step 2 -
Step 3 -
Step 4 -
Lay out the workpieces face down and label the inside faces with an “I” (Fig. N1).
Label the corners “A”, “B”, “C”, and “D” (Fig. N2).
Label the tail boards (drawer sides) with a “T” (Fig. N3).
Label the pin boards (drawer fronts) with a “P” (Fig. N4)
I
B
C
C
D
B
I
I
T
T
D
A
A
I
N1
N3
N2
DRAWERS
Tips for making drawers:
Tails (A) Fig. O1 are cut into the sides of the drawers, while pins (B) Fig. O1
are cut into the fronts and backs of drawers.
P
P
You can use either solid wood or plywood for the drawer bottoms (A) Fig. O2.
Insert the bottoms in a groove along the bottom of the fronts and sides.
Allow the drawer bottom to be free-floating (without glue) to allow for
seasonal expansion and contraction.
The grooves can go all the way to the ends of the boards if the joints are half-
blind dovetails. To accomplish this, position the groove so that it runs
through one of the tails on the side (Fig. O2). You will have to stop the
grooves on through dovetails or box joints before they reach the end of the
board to prevent them from being seen (Figs. O5 and O6).
N4
05
03
O1
B
A
WRONG
WRONG
06
B
04
02
A
RIGHT
HALF-BLIND DOVETAILS
GROOVE ALIGNED WITH TAIL
WRONG
HALF-BLIND DOVETAILS
GROOVE NOT ALIGNED WITH TAIL
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC JOINTS
THROUGH DOVETAILS
The through dovetail has a look that is visually appealing, especially in boxes and chests.
NOTE: For miniature through dovetails, use the 4215
accessory kit.
Cut both the pins and tails in the vertical position.
Cut the tails first.
Use two routers (if possible) - one for the pins and
the other for the tails - to make the process quicker
and easier.
If you are using the 4210 dovetail jig, you will need
the 4213 accessory kit to make this joint.
ITEMS NEEDED
ITEMS NEEDED FOR MINIATURE
●
●
●
●
●
●
●
●
●
●
Through Dovetail and Box Joint Template
17/32", 7° Dovetail Bit 43776PC
Miniature Dovetail Template
9/32", 7° Dovetail Bit 43777PC
13/32" Straight Bit, 43743PC
3/16" Straight Bit, 43014PC
3/4" O.D. Template Guide, 42040 (with dovetail bit)
5/8" O.D. Template Guide, 42046 (with straight bit)
Template Guide Lock Nut, 42239
3/8" O.D. Template Guide, 42037 (with dovetail bit)
5/16" O.D. Template Guide, 42055 (with straight bit)
Template Guide Lock Nut, 42239
●
●
CUTTING THE TAILS
Step 1 -
Clamp a spacer board (A) Fig. P1 (equal to the thickness of your pinboard) in the upper clamp. Mount the
through dovetail template (B) on the base with the “tails” side facing you.
Step 2 -
Move the offset guide (A) Fig. P2 to the far left.
Clamp the tailboard (A) Fig. P3 in the lower clamp with the outside surface of the board facing the jig.
Step 3-
(See the section “POSITIONING THE WOOD” in this manual.)
A
B
A
A
P1
P2
P3
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Reposition the offset guide (A) Fig. P4 flush to the vertical board and secure it.
Reposition the scrap board(A) Fig. P5 so that it is flush with the rear edge of the vertical board (B).
Align the template using the “tails/box” line (A) Fig. P6 with the line formed where the scrap board (B) and
the vertical board meet (C) and secure it.
Step 4 -
Step 5 -
Step 6-
A
A
C
B
B
A
P4
P6
P5
Step 7 - Mount the dovetail bit and 3/4" template guide on the router and set the router bit depth using the
“tail/box” depth guide (A) Fig. P7.
Step 8 -
Rout along the template fingers (Fig. P8). When the cut is complete, remove the vertical board.
A
P7
P8
NOTE:
If you prefer for your pins to protrude slightly for easier sanding, Adjust your router for a slightly deeper
cut. Once your optimum depth has been achieved, adjust the bit height guide with a 3/8" wrench.
CUTTING THE PINS
NOTE:
If the pin board is not the same thickness as the tail board, replace the scrap piece in the horizontal clamp
with a scrap board the same thickness as your tail board.
Step 1- Remove the template and rotate it 180 degrees so that the “pins” side is facing you. Clamp the pin board
in the lower clamp, flush against the left offset guide with the outside of the board facing away from the
jig.
Step 2 - Align the “pins” line (see the arrows) Fig. P10 on the template with the line formed where the scrap board
and pin board meet and tighten the template in place.
Step 3-
Mount the straight bit and the 5/8" templet guide on the router and set the router bit depth using the “pins”
bit depth guide (Fig. P11).
P10
P11
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5- Rout between the fingers of the template (Fig. P12).
Step 6 -
Remove the pin board and check the fit with the tailboard (Fig. P13).
P12
P13
THROUGH DOVETAIL TROUBLESHOOTING
For joints that are too loose, move the template toward you slightly.
For joints that are too tight, move the template away from you slightly.
HALF-BLIND DOVETAILS
The half-blind dovetail is one of the most common types of joints and is the ideal choice for the drawer construction.
In typical half-blind drawer construction, the joint is not visible from the front and is invisible when the drawer is
closed.
NOTE:
For miniature half-blinds, use the 4215 accessory
kit.
Use scrap wood until you are comfortable with the
jig.
You can cut half-blind pins and tails simultaneously
on the 4200 series jigs.
Mount the correct offset guides - black for the
standard and silver for the miniature.
ITEMS NEEDED
ITEMS NEEDED FOR MINIATURE
●
●
Half-blind Dovetail Template
Miniature Dovetail Template
●
●
●
●
17/32", 7° Dovetail Bit 43776PC
9/32", 7° Dovetail Bit 43777PC
●
3/4" O.D. Template Guide, 42040
Template Guide Lock Nut, 42239
3/8" O.D. Template Guide, 42037 (with dovetail bit)
Template Guide Lock Nut, 42239
Miniature Offset Guides (silver)
●
●
CUTTING HALF-BLIND DOVETAILS
Step 1 -
Step 2 -
Step 3 -
Clamp the pin board (drawer front) (A) Fig. Q1 in the upper clamp (horizontal mounting position) with the
outside of the board facing the jig.
Secure the template (B) on top of the pin board. Ensure the flatness by holding one hand on the template
and using the other to tighten the template knobs.
Move the left offset guide all the way to the left. (Use the black offset guides for the standard cut, and the
silver for the miniature cut).
A
B
Q2
Q1
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Clamp the tailboard (drawer side) in lower clamp (vertical
position) on the left side of the base with the outside of the board
facing the jig (A) Fig. Q3.
Step 4 -
CENTER
A
Step 5 -
Center the board between the farthest finger on the left and the
nearest finger on the right of the board.
Step 6 - Move the left offset guide (A) Fig. Q4 flush against the vertical
board (B) and secure it.
Step 7 -
Reposition the pin board (B) Fig. Q5 so that it is flush against the
offset guide (A) and the back edge of the vertical board (C).
Step 8 -
Align the template lines with the intersection of the pin board (A)
Fig. Q6 and tail board (B).
Q3
Step 9 -
Set the router bit depth using the bit-depth guide (A) Fig. Q7.
Step 10 -
Climb cut (from right to left) the outer edge of the vertical board (Fig. Q8) to reduce tearout.
Step 11 - Rout along the fingers of the template (Fig. Q9). Remove the boards from the jig and test for fit.
A
B
B
A
B
C
A
Q5
Q4
Q6
A
Q8
Q9
Q7
FITTING AND TROUBLESHOOTING
For joints that are too loose, adjust your router to make a deeper cut. (Measure the gap (A) Fig. Q10 in the test cut
and adjust the router for that amount).
For joints that are too tight, adjust your router to make a more shallow cut.
Once you achieve the correct depth, secure the router bit depth guide in place with a 3/8" wrench.
If the drawer front overlaps the drawer side, reposition the template toward you (Fig. Q11).
If the drawer front is recessed from the edge of the drawer side (Fig. Q12), reposition the template away from you.
A
A
Q10
Q11
Q12
18
Download from Www.Somanuals.com. All Manuals Search And Download.
RABBETED HALF-BLIND DOVETAILS
To produce rabbeted half-blind dovetails (drawer front), cut
the pins for a half-blind joint after the drawer front has been
rabbeted. The depth of the rabbet must be deeper than the
half-blind router bit depth guide.
NOTE:
Cut the tails first.
For miniature half-blinds, use the 4215 accessory
kit.
Use scrap wood until you are comfortable with the
jig.
Mount the correct offset guides - black for the
standard and silver for the miniature.
ITEMS NEEDED
ITEMS NEEDED FOR MINIATURE
●
●
Half-blind Dovetail Template
Miniature Dovetail Template
●
●
●
●
●
●
●
17/32", 7° Dovetail Bit 43776PC
3/4" O.D. Template Guide, 42040
Template Guide Lock Nut, 42239
9/32", 7° Dovetail Bit 43777PC
3/8" O.D. Template Guide, 42037 (with dovetail bit)
Template Guide Lock Nut, 42239
Miniature Offset Guides (silver)
CUTTING THE TAILS
Step 1 -
Clamp a scrap board (A) Fig. R1 in the upper clamp (horizontal mounting position). Use scrap board that
is thick enough to prevent the bit from contacting the base (1/2" will work). Secure the template (B) on
top of the scrap board (Fig. R1). Ensure the flatness by holding one hand on the board and using the other
to tighten the template knobs.
Move the left offset guide all the way to the left (Fig. R2). (Use the black offset guides for the standard
cut, and the silver for the miniature cut).
Step 2 -
Position and clamp the tail board in the lower clamp (vertical mounting position) with the outside surface
against the jig base (Fig. R3).
Step 3 -
B
A
R1
R2
R3
Step 4 -
Make a spacer equal to the rabbet’s width. Put the spacer (A) Fig. R4 against the left edge of the tail
board, move the left offset guide (B) flush against the spacer, and secure the offset guide.
Reposition the scrap board
(C) so that it is flush against
Step 5 -
A
the offset guide and the
back edge of the vertical
board.
B
C
Align the “half-blind” temp-
plate line (A) Fig. R5 with
the line formed where the
scrap board (B) and the
vertical board (C) meet.
B
Step 6 -
A
R4
R5
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7 -
Mount the dovetail bit and template guide to the router and set the router bit depth using the “half-blind”
bit depth guide (Fig. R6).
Step 8 -
Make a climb-cut from right to left across the outer edge of the tail board to reduce tear-out (Fig. R7).
Rout in and out of the fingers of the template from left to right (Fig. R8). Remove the boards.
Step 9 -
R6
R7
R8
CUTTING THE PINS
Step 1 -
Clamp the pin board in the upper clamp (horizontal mounting position) with the outside surface against
the jig’s base.
Step 2 -
Secure the template on top of the pin board making sure that it is flat (Fig. R9).
Step 3 -
Reposition the pin board (A) Fig. R10 so that it is flush to the left offset guide (B) and the inside edge of
the rabbet (A) Fig. R11 is aligned with the “half-blind” alignment line (B). Lower the router bit on the depth
guide and lock the position on your router.
Step 4 -
Rout in and out of the fingers of the template from left to right.
B
A
A
B
R9
R10
R11
Step 5 -
Remove the boards from the jig and test for fit.
NOTE:
Alternate method for aligning the pin board -
Use a board with a rabbet the same width as the
rabbet on the workpiece (R12).
R12
FITTING AND TROUBLESHOOTING
Fitting and troubleshooting methods for the lipped front half-blind dovetail are the same as for the regular half-
blind dovetail.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BOX JOINTS
Box joints have straight protrusions that interlock and must be
held together by glue. The large amount of gluing surface
provides the strength necessary for large projects.
NOTE:
If you are using the 4210 dovetail jig, you will need the 4213 accessory kit to make this joint. You will need
the 4215 accessory kit for the miniature box joints.
Box joint fingers are spaced in 1" increments (1/2" for miniature).
ITEMS NEEDED
ITEMS NEEDED FOR MINIATURE
●
●
●
Through Dovetail and Box Joint Template
1/2" diameter straight bit (not provided)
Length of the cutter must be at least
the thickness of the workpiece.
3/4" O.D. Template Guide, 42040
Template Guide Lock Nut, 42239
Miniature Dovetail Template
●
1/4" diameter straight bit (not provided)
At least 1/2" long cutter
●
●
3/8" O.D. Template Guide, 42037
Template Guide Lock Nut, 42239
●
●
CUTTING THE FIRST WORKPIECE
Step 1 -
Step 2 -
Step 3 -
Clamp a scrap board (A) Fig. S1 in the upper clamp (horizontal mounting position) that is the same
thickness as the second workpiece.
Use the T-handle wrench (A) Fig. S2 to loosen the screw on the left offset guide (B). Move the guide to
the far left.
Mount the workpiece (A) Fig. S3 in the lower clamp (vertical mounting position) with the outside surface
against the jig base.
A
A
B
A
S1
S2
S3
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4 -
Reposition the left offset guide (A) Fig. S4 flush against the workpiece (B).
Align the template, using the “tails/Box” template line with the line formed where the scrap board and the
workpiece meet.
Step 5 -
Step 6 -
Mount the straight bit and template guide on the router and set the router bit depth using the “tails/box”
bit depth guide.
B
A
S4
S5
Step 7 -
Rout between the fingers of the jig with the
templet guide against the left side of the
fingers, both in and out. This light pressure
toward the left will help to prevent loose joints.
Step 8 -
Remove the workpiece from the jig.
S6
CUTTING THE SECOND WORKPIECE
NOTE:
If the thickness is different between the first and second workpiece, replace the scrap piece in the upper
clamp (horizontal Mounting position) with another that is the same thickness as the first workpiece.
Step 1 -
Use the T-handle wrench (A) Fig. S8 to loosen the screw on the right offset guide (B) Fig.S10. Move the
guide to the far right.
Step 2 -
Clamp the first board in the lower clamp on the right side of the jig with the fingers protruding past the
template (Fig. S9).Center the protrusions of the wood in between the fingers of the templet.
Move the right offset guide flush against the workpiece and secure it with the T-handle wrench (Fig. S10).
Remove the first workpiece.
Step 3 -
Step 4 -
A
B
S9
S10
S8
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5 -
Clamp the second workpiece (A) Fig. S11 in the lower clamp (vertical mounting position) on the right side
of the jig flush against both the template (B) and against the right offset guide (C) with the outside surface
facing away from the jig.
If the first and second workpieces are of different thicknesses, reset the router bit depth using the
“tails/box” bit depth guide.
Step 6 -
Step 7 -
Step 8 -
Rout between the fingers of the jig with the templet guide against the left side of the fingers, both in and
out. This light pressure toward the left will help to prevent loose joints (Fig. S12).
Remove the second workpiece and assemble the joint (Fig. S13)
S11
S12
S13
NOTE:
The fit (tightness) of the box joint cannot be adjusted.
DOVETAIL DADOS (SLIDING DOVETAILS)
Dovetail dadoes (sliding dovetails) are used primarily in the construction of cabinets, entertainment centers and
shelving. The 4200 series jigs have three preset depths for dadoes ( 1/4", 3/8" and 1/2"), but you can manually set
your router bit depth to any setting.
NOTE:
Be certain that the router bit will not cut into the base or offset guides during this cut.Everything is provided
for this cut in both the 4210 and 4212 jigs.
ITEMS NEEDED
●
Dado Template
●
●
●
17/32", 7° Dovetail Bit 43776PC
3/4" O.D. Template Guide, 42040
Template Guide Lock Nut, 42239
CUTTING THE DADO BOARD
Step 1 -
Step 2 -
Step 3 -
Mark the centerline (A) Fig. T1 of the dado location on the workpiece.
Make two marks 3/8" from the centerline of the dado (B) Fig. T1.
Insert the workpiece (A) Fig. T2 in the upper clamp (horizontal clamping position) and place the dado
template (B) on the jig with the dado side facing you. Adjust the template so that the lines that you drew
in STEP 2 (C) are aligned exactly with the edges of the slot.
C
B
A
B
A
T1
T2
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4 -
Set your router bit depth by using either of the three choices (A, B, or C) Fig. T3 on the left side of the
template, or by manually setting the router to another depth.
Step 5 -
Slowly rout along the slot from left to right (Fig. T4). (Some deep dadoes may require cutting the bulk of
the material with a straight bit).
Step 6 - Remove the workpiece.
A
B
C
T4
T3
CUTTING THE TENON BOARD
Step 1 -
Step 2 -
Step 3 -
Step 4 -
Step 5 -
Mount a scrap board (A) Fig. T6 in the upper clamp (horizontal mounting position)
Mount the tenon board (B) Fig. T6 in the lower clamp (vertical mounting position).
Make a climb cut (from right to left) on the front edge of the template.
Make another cut from left to right along the front edge of the template.
Remove the tenon board. Keep the same end up and turn the board so that the cut side of the board
faces the base. Repeat STEPS 3 and 4.
Step 6 -
Remove the tenon board and fit the joint.
A
B
T7
T6
FITTING AND TROUBLESHOOTING
For joints that are too loose, move the template toward you and recut the tenon board.
For joints that are too tight, move the template away from you and recut the tenon board.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
KEEP TOOL CLEAN
Periodically blow out all air passages with dry compressed air. Clean all plastic parts with a soft damp cloth. NEVER
use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.
WEAR ANSI Z87.1 SAFETY GLASSES WHILE USING COMPRESSED AIR.
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These
operations, including brush inspection and replacement, should ONLY be performed by either an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE·DELTA FACTORY SERVICE CENTER. All repairs made by
these agencies are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made
or attempted by anyone other than these agencies.
Should you have any questions about your tool, feel free to write us at any time. In any communications, please give
all information shown on the nameplate of your tool (model number, type, serial number, etc.).
ACCESSORIES
A complete line of accessories is available from your Porter-Cable•Delta Supplier, Porter-Cable•Delta Factory
Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com
for a catalog or for the name of your nearest supplier.
Since accessories other than those offered by Porter-Cable•Delta have not been tested with
this product, use of such accessories could be hazardous. For safest operation, only
Porter-Cable•Delta recommended accessories should be used with this product.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
PORTER-CABLE LIMITED
ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories covered
under this warranty which, after examination, proves to be defective in workmanship or material during the
warranty period. For repair or replacement return the complete tool or accessory, transportation prepaid, to
your nearest Porter-Cable Service Center or Authorized Service Station. Proof of purchase may be required.
This warranty does not apply to repair or replacement required due to misuse, abuse, normal wear and tear
or repairs attempted or made by other than our Service Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE OF
PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION, 4825
Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING OBLIGATION
IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY AND UNDER NO
CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary from state
to state.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
•
Delta Machinery are Available at These Locations
•
Delta)
OREGON
ARIZONA
MINNESOTA
GEORGIA
Portland 97230
Phoenix 85013-2906
4501 N. 7th Ave.
Phone: (602) 279-6414
Fax: (602) 279-5470
Eden Prairie 55344
9709 Valley View Road
Phone: (952) 884-9191
Fax: (952) 884-3750
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
14811 North East Airport Way
Phone: (503) 255-6556
Fax: (503) 255-6543
Phone: (404) 608-0006
Fax: (404) 608-1123
CALIFORNIA
PENNSYLVANIA
Willow Grove 19090
(Philadelphia)
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
MISSOURI
St. Louis 63146
11477 Page Service Drive
Phone: (314) 997-9100
Fax: (314) 997-9183
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
ILLINOIS
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
San Diego 92111
NEW YORK
7290 Clairemont Mesa Blvd.
Phone: (858) 279-2011
Fax: (858) 279-0362
TEXAS
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
KANSAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Overland Park 66214
9201 Quivira Road
Phone: (913) 495-4330
Fax: (913) 495-4378
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
MARYLAND
Houston 77022-2122
536 East Tidwell Rd.
Phone: (713) 692-7111
Fax: (713) 692-1107
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
COLORADO
Denver 80223
700 West Mississippi Ave.
Phone: (303) 922-8325
Fax: (303) 922-0245
OHIO
WASHINGTON
Columbus 43229
1948 Schrock Road
Phone: (614) 895-3112
Fax: (614) 895-3187
MASSACHUSETTS
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Parma Heights OH 44130
6485 Pearl Road
Phone: (440) 842-9100
Fax: (440) 884-3430
Phone: (954) 321-6635
Fax: (954) 321-6638
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
Tampa 33634
4909 West Waters Ave.
Phone: (813) 884-0434
Fax: (813) 888-5997
Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable·Delta products should be obtained by contacting any Porter-Cable·Delta Distributor, Authorized
Service Center, or Porter-Cable·Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will
be directed to the nearest Porter-Cable·Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas
grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable·Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centro
de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable·Delta. Si no tiene acceso a ninguna de estas opciones, llame al
800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable·Delta más cercano.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
QUÉBEC
MANITOBA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1515 ave.
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste, Suite 160
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
ONTARIO
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
1447, Begin
505 Southgate Drive
Guelph, Ontario
N1H 6M7
St-Laurent, (Montréal),
Québec
V5A 4T8
H4R 1V8
Phone: (519) 767-4132
Fax: (519) 767-4131
Phone: (604) 420-0102
Fax: (604) 420-3522
Phone: (514) 336-8772
Fax: (514) 336-3505
The following are trademarks of PORTER-CABLE
•
DELTA (Las siguientes son marcas registradas de PORTER-CABLE
•
DELTA S.A.) (Les marques
suivantes sont des marques de fabriquant de la PORTER-CABLE
•
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®,
Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®,
Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®,
MORTEN™, NETWORK™, OMNIJIG®, POCKET
CUTTER®,
PORTA-BAND®,
PORTA-PLANE®,
PORTER-CABLE®&(design), PORTER-
CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design),
QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW
BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber
Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,
TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®,
Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®, WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las
Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar
registradas en otros países.
PC7.2-0105-149
Download from Www.Somanuals.com. All Manuals Search And Download.
|