Porter Cable Saw 38129 User Manual

ESPAÑOL: PÁGINA 23  
FRANÇAISE : PAGE 43  
Double Insulated  
10" Bench Top Table Saw  
Instruction  
Manual  
MODEL 3812  
Shown assembled with accessory stand model 38129  
and accessory outfeed support model 38239.  
IMPORTANT  
Please make certain that the person who is to use  
this equipment carefully reads and understands  
these instructions before starting operations.  
To learn more about Porter-Cable  
visit our website at:  
The Model and Serial No. plate is located on the main  
housing of the tool. Record these numbers in the  
spaces below and retain for future reference.  
Model No. _____________________________________  
Type __________________________________________  
Serial No.______________________________________  
Part No. 912933 - 09-15-03  
Copyright © 2003 PORTER-CABLE Corporation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.  
1.  
2.  
FOR YOUR OWN SAFETY, READ THE INSTRUC-  
13. USE RECOMMENDED ACCESSORIES. The use  
of accessories and attachments not recom-  
mended by Porter-Cable may cause damage to  
the machine or injury to the user.  
TION MANUAL BEFORE OPERATING THE  
MACHINE. Learning the machine’s application,  
limitations, and specific hazards will greatly  
minimize the possibility of accidents and injury.  
14. USE THE PROPER EXTENSION CORD. Make  
sure your extension cord is in good condition.  
When using an extension cord, be sure to use one  
heavy enough to carry the current your product will  
draw. An undersized cord will cause a drop in line  
voltage, resulting in loss of power and overheating.  
See the Extension Cord Chart for the correct size  
depending on the cord length and nameplate  
ampere rating. If in doubt, use the next heavier  
gauge. The smaller the gauge number, the heavier  
the cord.  
15. SECURE THE WORKPIECE. Use clamps or a vise to  
hold the workpiece when practical. Loss of control  
of a workpiece can cause injury.  
16. FEED THE WORKPIECE AGAINST THE DIRECTION  
OF THE ROTATION OF THE BLADE, CUTTER, OR  
ABRASIVE SURFACE. Feeding it from the other  
direction will cause the workpiece to be thrown out  
at high speed.  
USE CERTIFIED SAFETY EQUIPMENT. Eye  
protection equipment should comply with ANSI  
Z87.1 standards, hearing equipment should  
comply with ANSI S3.19 standards, and dust mask  
protection should comply with MSHA/NIOSH  
certified respirator standards. Splinters, air-borne  
debris, and dust can cause irritation, injury, and/or  
illness.  
DRESS PROPERLY. Do not wear tie, gloves, or  
loose clothing. Remove watch, rings, and other  
jewelry. Roll up your sleeves. Clothing or jewelry  
caught in moving parts can cause injury.  
DO NOT USE THE MACHINE IN A DANGEROUS  
ENVIRONMENT. The use of power tools in damp  
or wet locations or in rain can cause shock or  
electrocution. Keep your work area well-lit to  
prevent tripping or placing arms, hands, and  
fingers in danger.  
3.  
4.  
5.  
6.  
MAINTAIN ALL TOOLS AND MACHINES IN PEAK  
CONDITION. Keep tools sharp and clean for best and  
safest performance. Follow instructions for lubricating  
and changing accessories. Poorly maintained tools and  
machines can further damage the tool or machine and/or  
cause injury.  
CHECK FOR DAMAGED PARTS. Before using the  
machine, check for any damaged parts. Check for  
alignment of moving parts, binding of moving  
parts, breakage of parts, and any other conditions  
that may affect its operation. A guard or any other  
part that is damaged should be properly repaired  
or replaced. Damaged parts can cause further  
damage to the machine and/or injury.  
17. DON’T FORCE THE WORKPIECE ON THE  
MACHINE. Damage to the machine and/or injury  
may result.  
18. DON’T OVERREACH. Loss of balance can make  
you fall into a working machine, causing injury.  
19. NEVER STAND ON THE MACHINE. Injury could occur if  
the tool tips, or if you accidentally contact the cutting tool.  
20. NEVER LEAVE THE MACHINE RUNNING UNATTEN-  
DED. TURN THE POWER OFF. Don’t leave the machine  
until it comes to a complete stop. A child or visitor could  
be injured.  
21. TURN THE MACHINE “OFF”, AND DISCONNECT THE  
MACHINE FROM THE POWER SOURCE before  
installing or removing accessories, before adjusting  
or changing set-ups, or when making repairs. An  
accidental start-up can cause injury.  
22. MAKE YOUR WORKSHOP CHILDPROOF WITH  
PADLOCKS, MASTER SWITCHES, OR BY  
REMOVING STARTER KEYS. The accidental  
start-up of a machine by a child or visitor could  
cause injury.  
23. STAY ALERT, WATCH WHAT YOU ARE DOING,  
AND USE COMMON SENSE. DO NOT USE THE  
MACHINE WHEN YOU ARE TIRED OR UNDER  
THE INFLUENCE OF DRUGS, ALCOHOL, OR  
MEDICATION. A moment of inattention while  
operating power tools may result in injury.  
7.  
8.  
KEEP THE WORK AREA CLEAN. Cluttered areas and  
benches invite accidents.  
KEEP CHILDREN AND VISITORS AWAY. Your shop is  
a potentially dangerous environment. Children and visitors  
can be injured.  
REDUCE THE RISK OF UNINTENTIONAL STARTING.  
Make sure that the switch is in the “OFF” position  
before plugging in the power cord. In the event of  
a power failure, move the switch to the “OFF”  
position. An accidental start-up can cause injury.  
9.  
10. USE THE GUARDS. Check to see that all guards  
are in place, secured, and working correctly to  
prevent injury.  
11. REMOVE ADJUSTING KEYS AND WRENCHES  
BEFORE STARTING THE MACHINE. Tools, scrap  
pieces, and other debris can be thrown at high  
speed, causing injury.  
12. USE THE RIGHT MACHINE. Don’t force a  
machine or an attachment to do a job for which it  
was not designed. Damage to the machine and/or  
injury may result.  
24. THE DUST GENERATED by certain woods and  
wood products can be injurious to your health.  
Always operate machinery in well-ventilated areas,  
and provide for proper dust removal. Use wood  
dust collection systems whenever possible.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADDITIONAL SAFETY RULES FOR  
TABLE SAWS  
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.  
10. NEVER perform “free-hand” operations. Use either  
the fence or miter gauge to position and guide the  
workpiece.  
1. DO NOT OPERATE THIS MACHINE until it is  
assembled and installed according to the  
instructions.  
11. HOLD THE WORKPIECE FIRMLY against the miter  
2. OBTAIN ADVICE FROM YOUR SUPERVISOR,  
instructor, or another qualified person if you are  
not familiar with the operation of this machine.  
gauge or fence.  
12. USE PUSH STICK(S) for ripping a narrow  
workpiece.  
3. FOLLOW ALL WIRING CODES and recommended  
electrical connections.  
13. AVOID AWKWARD OPERATIONS AND HAND  
POSITIONS where a sudden slip could cause a  
hand to move into the blade.  
4. USE THE GUARDS WHENEVER POSSIBLE.  
Check to see that they are in place, secured, and  
working correctly.  
14. KEEP ARMS, HANDS, AND FINGERS away from  
5. AVOID KICKBACK by:  
the blade.  
A. keeping blade sharp and free of rust and pitch.  
B. keeping rip fence parallel to the saw blade.  
C. using saw blade guard and spreader for every  
possible operation, including all through  
sawing.  
D. pushing the workpiece past the saw blade prior  
to release.  
E. never ripping a workpiece that is twisted or  
warped, or does not have a straight edge to  
guide along the fence.  
F. using featherboards when the anti-kickback  
device cannot be used.  
G. never sawing a large workpiece that cannot be  
controlled.  
H. never using the fence as a guide when  
crosscutting.  
I. never sawing a workpiece with loose knots or  
other flaws.  
15. NEVER have any part of your body in line with the  
path of the saw blade.  
16. NEVER REACH AROUND or over the saw blade.  
17. NEVER attempt to free a stalled saw blade without  
first turning the machine “OFF”.  
18. PROPERLY SUPPORT LONG OR WIDE  
workpieces.  
19. NEVER PERFORM LAYOUT, assembly or set-up  
work on the table/work area when the machine is  
running.  
20. TURN THE MACHINE “OFF” AND DISCONNECT  
THE MACHINE from the power source before  
installing or removing accessories, before adjusting  
or changing set-ups, or when making repairs.  
21. TURN THE MACHINE “OFF”, disconnect the  
machine from the power source, and clean the  
table/work area before leaving the machine. LOCK  
THE SWITCH IN THE “OFF” POSITION to prevent  
unauthorized use.  
6. ALWAYS USE GUARDS, SPLITTER, AND ANTI-  
KICKBACK FINGERS whenever possible.  
7. REMOVE CUT-OFF PIECES AND SCRAPS from  
the table before starting the saw. The vibration of the  
machine may cause them to move into the saw  
blade and be thrown out. After cutting, turn the  
machine off. After the blade has come to a  
complete stop, remove all debris.  
22. ADDITIONAL INFORMATION regarding the safe  
and proper operation of power tools (i.e. a safety  
video) is available from the Power Tool Institute,  
1300 Sumner Avenue, Cleveland, OH 44115-2851  
available from the National Safety Council, 1121  
Spring Lake Drive, Itasca, IL 60143-3201. Please  
refer to the American National Standards Institute  
ANSI 01.1 Safety Requirements for Woodworking  
Machines and the U.S. Department of Labor OSHA  
1910.213 Regulations.  
8. NEVER START THE MACHINE with the workpiece  
against the blade.  
9. NEVER run the workpiece between the fence and a  
moulding cutterhead.  
SAVE THESE INSTRUCTIONS.  
Refer to them often  
and use them to instruct others.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
POWER CONNECTIONS  
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should  
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-  
prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the  
machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of  
the same characteristics as indicated on the machine. All line connections should make good contact. Running on low  
voltage will damage the machine.  
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.  
POLARIZED PLUGS: To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than  
the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still  
does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.  
MOTOR  
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus  
or minus 5 percent of that shown on the specification plate of the tool. Several models, however, are designed for A.C.  
current only. Refer to the specification plate on your tool for proper voltage and current rating.  
Do not operate your tool on a current where the voltage is not within correct limits. Do not operate tools  
rated A.C. on a D.C. current. To do so may seriously damage the tool.  
REPLACEMENT PARTS  
When servicing, use only identical replacement parts.  
EXTENSION CORDS  
Use proper extension cords. Make sure your extension  
cord is in good condition. When using an extension  
cord, be sure to use one heavy enough to carry the  
current of the machine. An undersized cord will cause a  
drop in line voltage, resulting in loss of power and  
overheating. Fig. D, shows the correct gauge to use  
depending on the cord length. If in doubt, use the next  
heavier gauge. The smaller the gauge number, the  
heavier the cord.  
MINIMUM GAUGE EXTENSION CORD  
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES  
Ampere  
Rating  
0-6  
0-6  
0-6  
0-6  
6-10  
6-10  
6-10  
6-10  
10-12  
10-12  
10-12  
10-12  
Total Length  
of Cord in Feet  
Gauge of  
Extension Cord  
Volts  
120  
120  
120  
120  
up to 25  
25-50  
50-100  
100-150  
18 AWG  
16 AWG  
16 AWG  
14 AWG  
120  
120  
120  
120  
up to 25  
25-50  
50-100  
100-150  
18 AWG  
16 AWG  
14 AWG  
12 AWG  
120  
120  
120  
120  
up to 25  
25-50  
50-100  
100-150  
16 AWG  
16 AWG  
14 AWG  
12 AWG  
12-16  
12-16  
12-16  
120  
120  
120  
up to 25  
25-50  
14 AWG  
12 AWG  
GREATER THAN 50 FEET NOT RECOMMENDED  
Fig. D  
FUNCTIONAL DESCRIPTION  
FOREWORD  
The Porter-Cable Model 3812 is a 10" Bench Top Table Saw. The saw comes with a 26"x20" table surface with a rip  
fence extension wing which provides a 24½" rip capacity for ripping 4x8 sheets. The Model 3812 comes with a Riptide™  
24 tooth carbide-tipped blade, miter gauge, rip fence, quick release blade guard, and blade changing wrenches.  
UNPACKING AND CLEANING  
Carefully unpack the machine and all loose items from the shipping container. Remove the protective coating from all  
unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline  
or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste  
wax.  
NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT  
PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE  
ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR  
ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARTON CONTENTS  
1
2
4
3
9
8
5
7
6
Fig. 2  
1. Saw  
2. Fence  
3. Table Insert  
4. Blade Guard and Spreader Assembly  
5. Blade Wrench (2)  
6. Miter Gauge  
7. Anchor Block Shim (3)  
8. Handle  
9. 1/4"-20x1-3/4" Screw  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL  
THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE  
INSTRUCTION MANUAL.  
BLADE RAISING AND  
LOWERING HANDWHEEL  
E
D
Insert the 1-3/4" screw (D) Fig. 4, through handle (E).  
Assemble handle (E) to handwheel (A) by threading  
screw (D) clockwise into handwheel as shown in Fig. 5.  
Handle (E) should rotate freely on screw (D).  
Fig. 4  
E
D
A
Fig. 5  
BLADE GUARD AND  
SPREADER ASSEMBLY  
1.  
DISCONNECT MACHINE FROM  
POWER SOURCE.  
A
2.  
THE BLADE GUARD AND SPREADER  
ASSEMBLY MUST BE PROPERLY ALIGNED TO THE  
SAW BLADE IN ORDER TO HELP PREVENT  
KICKBACK.  
B
3. Position the blade 90 degrees to the table and lock  
in place.  
Fig. 6  
4. Insert spreader end (A) Fig. 6, of blade guard into  
anchor block (B). Push spreader (A) down into holder  
until you hear a click, indicating that the spreader is  
secured. NOTE: It is important that the spreader (A) be  
in the vertical position and pushed straight down into the  
spreader anchor block (B) during the assembly  
procedure.  
5. Fig. 7 illustrates the blade guard in place.  
Fig. 7  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. NOTE: The anchor block (B) Fig. 6, has been  
adjusted at the factory so that the spreader will be  
aligned with the saw blade which is supplied with the  
saw. When changing to blades with different widths it  
may be necessary to adjust the anchor block (B) Fig. 9,  
as follows:  
7. Remove table insert and saw blade.  
8. Loosen the two screws (C) Fig. 8 (under saw table),  
that attach the anchor block (B) Fig. 9, to the saw frame  
(E).  
C
9. Three additional shims, two of which are shown at  
(D) Fig. 9, are supplied with your saw and can be used as  
required between the anchor block (B) and the frame (E)  
in order to align the spreader with the saw blade.  
Fig. 8  
B
10. After adjustment is completed, tighten the two  
screws (C) Fig. 8.  
D
REMOVING BLADE  
GUARD/SPREADER  
ASSEMBLY  
E
DISCONNECT TOOL FROM POWER  
SOURCE.  
Fig. 9  
The blade must be in the 90 degree position to the table  
for the blade guard and spreader assembly to be  
removed. Remove the table insert, pull out on the  
spreader release spring (A) Fig. 9A, while pulling up on  
the blade guard/spreader assembly (B). NOTE: STORE  
THE BLADE GUARD AS SHOWN IN FIG. 31A, WHEN  
THE BLADE GUARD IS NOT IN USE.  
B
A
MITER GAGE  
The miter gage is shipped completely assembled and is  
supplied with a T-slot miter gage bar (A) Fig. 10, that can  
be inserted into either one of the two T-slotted miter  
gage grooves located in the table top, as shown. The T-  
slot miter gage can be extended beyond the front of the  
table for cross-cutting wide workpieces.  
Fig. 9A  
MITER GAGE HOLDER  
Fig. 11, illustrates the miter gage (D) inserted into the  
miter gage holder when not in use.  
A
D
Fig. 10  
Fig. 11  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
RIP FENCE TO SAW TABLE  
1. The rip fence may be used on the right or left hand  
side of the saw table. Lift locking handle (A) Fig. 12, and  
position the front end of the fence on the front fence rail  
as shown.  
A
2. While pressing front end of fence firmly against front  
fence rail, place rear end of fence down on the rear  
fence rail and push down on locking handle (A) Fig. 13,  
to lock fence in place.  
Fig. 12  
FASTENING SAW TO A  
SUPPORTING SURFACE  
A
The saw MUST be properly secured to a supporting  
surface using the four mounting holes, two of which are  
shown at (A) Fig. 14.  
Fig. 13  
THE SUPPORTING SURFACE MUST BE  
ABLE TO SUPPORT 300LBS.  
A HOLE MUST BE PROVIDED IN THE SUPPORTING  
SURFACE TO FACILITATE SAWDUST FALL-THRU  
AND REMOVAL. Square the saw on the supporting  
surface and mark the location of the four 5/16 inch holes  
to be drilled, as shown in Fig. 15. Locate and mark an 11  
or 12 inch square centered between the four mounting  
holes and cut out and remove the square, as shown in  
Fig. 15. This opening will allow sawdust to fall through  
the saw base. Fasten the saw to the workbench utilizing  
the mounting holes that were just drilled.  
A
Fig. 14  
FAILURE TO PROVIDE THIS SAW DUST  
FALL-THRU AND REMOVAL HOLE WILL ALLOW  
SAW DUST TO BUILD-UP AROUND THE MOTOR  
WHICH MAY RESULT IN A FIRE HAZARD OR CAUSE  
MOTOR DAMAGE.  
SAW PLACEMENT  
MARKS  
5/16" HOLES  
FASTENING SAW TO TWO  
SAW HORSES  
When fastening the saw to two saw horses, position the  
four grooves located on the base of the saw cabinet  
over the 2x4’s of the saw horse and fasten in place with  
suitable hardware (not supplied). CAUTION: THE SAW  
HORSES MUST BE ABLE TO SUPPORT 300 LBS.  
Fig. 15  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING CONTROLS AND ADJUSTMENTS  
STARTING AND STOPPING  
SAW  
The “ON/OFF” switch (A) Fig 16, is located on the front  
of the saw cabinet. To turn the saw “ON” pull the  
“ON/OFF” switch (A) out. To turn the saw “OFF”, push  
in on the “ON/OFF” switch (A).  
A
SOFT START  
Model 3812 has a “Soft Start” feature designed to  
minimize startup reaction torque.  
LOCKING SWITCH IN THE  
Fig. 16  
“OFF” POSITION  
IMPORTANT: When the tool is not in use the switch  
should be locked in the “OFF” position to prevent  
unauthorized use. The tool can be locked in the “OFF”  
position using a padlock (A) as shown in Fig. 17.  
The padlock should have 3/16" diameter shank with a 2"  
throat to insure a proper fit.  
BLADE RAISING AND  
LOWERING CONTROL  
To raise or lower the saw blade, turn handwheel (A) Fig  
18. Turning the handwheel counterclockwise lowers the  
blade and turning the handwheel clockwise raises the  
A
blade.  
Fig. 17  
THE BLADE TILTING LOCK HANDLE (B)  
FIG. 19, MUST BE LOCKED DURING ALL CUTTING  
OPERATIONS.  
BLADE TILTING CONTROL  
To tilt the saw blade, loosen blade tilting lock handle (B)  
Fig. 19, rotate outer wheel (C) until the blade is at the  
desired angle and tighten lock handle (B).  
THE BLADE TILTING LOCK HANDLE (B)  
FIG. 19 MUST BE LOCKED DURING ALL CUTTING  
OPERATIONS.  
A
ADJUSTING TABLE INSERT  
Place a straight edge (B) across the table at both ends of  
Fig. 18  
the table insert as shown in Fig. 19A. The table insert (A)  
should always be level with the table. If an adjustment is  
necessary, turn the adjusting screws (C), as needed. Four  
adjusting screws (C) are supplied.  
B
C
C
C
A
B
Fig. 19A  
Fig. 19  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADJUSTING 0 AND 45  
DEGREE POSITIVE STOPS  
A
Your saw is equipped with positive stops for rapid and  
accurate positioning of the saw blade at 0 and 45  
degrees to the table. This saw has the capability to go 2  
degrees beyond 0 and 45 degrees (-2º to 47º). To adjust  
the positive stops, proceed as follows:  
1.  
DISCONNECT MACHINE FROM  
POWER SOURCE.  
B
2. Remove the blade guard and spreader assembly.  
NOTE: SEE THE SECTION “REMOVING BLADE  
GUARD/SPREADER ASSEMBLY.”  
Fig. 20  
3. Raise the saw blade to its maximum height.  
TO ADJUST POSITIVE STOP AT 0 DEGREES  
4. Loosen the blade tilting lock handle, move the blade  
tilting mechanism as far as possible to the left and  
tighten the blade tilting lock handle.  
A
5. Place a square (A) Fig. 20, on the table with one end  
of the square against the blade, as shown, and check to  
see if the blade is at 90 degrees to the table. If it is not,  
loosen screw (B) a few turns and move the blade tilting  
mechanism until the blade measures 90 degrees to the  
table. Then tighten blade tilting lock handle and tighten  
screw (B) until it bottoms. NOTE: CHECK TO SEE IF THE  
TILT INDICATOR POINTER POINTS TO THE ZERO  
MARK ON THE SCALE. ADJUST IF NECESSARY.  
C
Fig. 21  
TO ADJUST POSITIVE STOP AT 45 DEGREES  
6. Loosen the blade tilting lock handle, move the blade  
tilting mechanism as far as possible to the right and  
tighten the blade tilting lock handle.  
7. Place a square (A) Fig. 21, on the table with one end  
of the square against the blade as shown, and check to  
see if the blade is at 45 degrees to the table. If it is not,  
loosen screw (C) a few turns and move the blade tilting  
mechanism until the blade is at 45 degrees to the table.  
Then tighten blade tilting lock handle and tighten screw  
(C) until it bottoms.  
B
A
F
RIP FENCE OPERATION  
AND ADJUSTMENTS  
D
D
1. To move the rip fence (A) Fig. 22A, along the table,  
lift up fence locking lever (B), slide the fence to the  
desired location on the table and push down fence  
locking lever (B) to lock the fence in position.  
Fig. 22A  
2. A pointer is supplied to indicate the distance the  
fence is positioned away from the saw blade. If an  
adjustment to the pointer (D) is required, loosen the  
screws (C) Fig. 22B, that fasten the pointer window to  
the fence head and adjust the pointer accordingly.  
NOTE: THE RIP SCALE HAS TWO SETS OF  
MEASUREMENTS DISPLAYED ON IT. THE TOP  
SCALE IS USED WHEN THE RIP FENCE GUIDE RAIL  
IS COLLAPSED. THE BOTTOM SCALE IS USED  
WHEN THE RIP FENCE GUIDE RAIL IS FULLY  
EXTENDED.  
D
C
Fig. 22B  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.  
THE RIP FENCE MUST BE PARALLEL  
TO THE MITER GAGE SLOT AND SAW BLADE TO  
HELP PREVENT KICKBACK WHEN RIPPING.  
4. The saw blade is set parallel to the miter gage slot at  
the factory and the fence must be parallel to the miter  
gage slot and saw blade in order to do accurate work and  
help prevent kickback when ripping. To check the  
alignment:  
5. Position the fence close to the miter gage slot, as  
shown in Fig. 22A. Push fence toward saw to insure  
alignment screws are in contact with the fence rail. Clamp  
the fence to the table by pushing down the locking lever  
(B). The fence should be parallel with the miter gage slot.  
6. If an adjustment is necessary, proceed as follows:  
7. Loosen the two screws and jam nuts (D) Fig. 22A, and  
lift up locking lever (B). Then while holding the fence  
bracket (F) Fig. 22A firmly toward the rear, move the rear  
end of the fence (A), by adjusting the two screws (D) until  
the fence is parallel with the miter gage slot. Then push  
down locking lever (B). Tighten jam nuts (D) on adjusting  
screws.  
B
H
E
G
Fig. 23  
8. The clamping action of the fence (A) Fig. 23, can be  
adjusted by lifting up locking lever (B) and turning nut (E)  
clockwise to increase or counterclockwise to decrease  
the tension of the clamping action of the fence.  
REPLACING THE RIP FENCE  
SCALE  
A metric scale can be attached to the rip fence as  
follows:  
1. Extend the rip fence guide rail as far as it will go.  
2. Use a pencil and “mark” the guide rail at the “0”  
location of the scale and remove the standard scale.  
3. Place the metric scale on the guide rail referencing the  
“0” mark.  
4. Collapse the guide rail and check to see if the “0”  
mark is accurate.  
A
Fig. 24  
5. If an adjustment is necessary, adjust the “0” mark by  
loosening nut (G) Fig. 23, and turning screw (H)  
clockwise to move the “0” mark to the left, and counter  
clockwise to move the “0” mark to the right, once the “0”  
is set properly on the rip fence guide rail, turn nut (G)  
counterclockwise to lock nut (G) against screw (H).  
RIP FENCE EXTENSION  
The saw has the capability to increase its ripping  
capacity by extending the rip fence guide rails.  
To extend the rip fence guide rails pull lever (A) Fig. 24,  
to the right, and pull out on the guide rails. Then lock the  
extended rails.  
C
B
RIPPING THIN STOCK  
To adjust the fence, pull up on lever (B) so that the top of  
the rip fence can be removed, and repositioned on the  
rip fence as shown in Fig. 25. This is only necessary  
when the fence guide rails are extended.  
When using the guide rails for ripping, the fence must be  
positioned as shown in Fig. 25, so that the wood can rest  
on the ledge (C,) up against the rip fence.  
An auxiliary wood insert can be placed in the gap  
between the saw table and the rip fence extension to  
add extra support.  
Fig. 25  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MITER GAGE OPERATION  
AND ADJUSTMENTS  
When straight cross-cutting (blade set 90 degrees to the  
table) the miter gage can be used in either table slot.  
When bevel cross-cutting (blade tilted) only use the  
miter gage in the right table slot where the blade is tilted  
away from the miter gage and your hands.  
This miter gage is equipped with individually adjustable  
index stops at 90 degrees and 45 degrees right and left.  
Adjustment to the index stops can be made by  
loosening lock nuts (B) Fig. 26, and tightening or  
loosening the three adjusting screws (C) until they  
contact the other end of stop guard (D) when the miter  
gage is at 90 and 45 degrees to the saw blade.  
To operate the miter gage, simply loosen lock knob (E)  
Fig. 26, and move the body of the miter gage to the  
desired angle.  
E
B
C
D
Fig. 26  
B
A
ADJUSTING BLADE  
PARALLEL TO  
Fig. 27  
MITER GAGE SLOTS  
The blade was adjusted parallel to the miter gage slots  
at the factory. In order to insure accurate cuts and help  
prevent kickback when cutting, this adjustment should  
be periodically checked and if necessary, adjusted as  
follows:  
1.  
DISCONNECT MACHINE FROM  
POWER SOURCE.  
2. Raise the blade to its highest position and adjust the  
blade so it is 90 degrees to the table.  
Fig. 27A  
3. Select a tooth on the saw blade that is set to the  
left. Mark this tooth with a pencil or marker.  
4. Using a combination square, place the body (A) Fig.  
27, of the square against the miter gage slot and adjust  
the blade (B) of the square until it just touches the  
marked tooth, as shown.  
A
5. Rotate the blade and check the same marked blade  
tooth at the rear of the saw table in the same manner, as  
shown in Fig. 27A.  
6. If the front and back measurements, shown in Figs.  
27 and 27A, are not identical, loosen the four trunnion  
bolts (A) Fig. 28, underneath the saw table. Carefully  
grasp and move the saw frame until the blade is parallel  
to the miter gage slot. Then tighten the four trunnion  
bolts securely.  
Fig. 28  
B
DUST PORT  
The saw has a dust port (B) Fig. 28A, located at the rear  
of the saw. The dust port is for connecting a dust  
collection system to the saw. The port is 2-1/2" outside  
diameter.  
Fig. 28A  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATIONS  
Common sawing operations include ripping and cross-cutting plus a few other standard operations of a fundamental  
nature. As with all power tools, there is a certain amount of hazard involved with the operation and use of the tool.  
Using the tool with the respect and caution demanded as far as safety precautions are concerned, will considerably  
lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal  
injury to the operator can result. The following information describes the safe and proper method for performing the  
most common sawing operations.  
CROSS-CUTTING  
Cross-cutting requires the use of the miter gage to position and guide the work. Place the work against the miter gage  
and advance both the gage and work toward the saw blade, as shown in Fig. 32. The miter gage may be used in either  
table slot. When bevel cutting (blade tilted), use the miter gage slot that does not cause interference of your hand or  
miter gage with the saw blade guard. The saw guard must always be used for all through cutting.  
Start the cut slowly and hold the work firmly against the miter gage and the table. One of the rules in running a saw is  
that you never hang onto or touch a free piece of work. Hold the supported piece, not the free piece that is cut off. The  
feed in cross-cutting continues until the work is cut in two, and the miter gage and work are pulled back to the starting  
point. Before pulling the work back it is good practice to give the work a little sideways shift to move the work slightly  
away from the saw blade. Never pick up any short length of free work from the table while the saw is running.  
WARNING: NEVER USE THE FENCE AS A CUT-  
OFF GAGE WHEN CROSS-CUTTING.  
For added safety and convenience the miter gage can  
be fitted with an auxiliary wood-facing. This auxiliary  
wood-facing can be fastened to the front of the miter  
gage by using two wood screws through the slots  
provided in the miter gage body and into the wood-  
facing.  
RIPPING  
Ripping is the operation of making a length-wise cut  
through a board, as shown in Fig. 33, and the rip fence  
Fig. 32  
(A) is used to position and guide the work. One edge of  
the work rides against the rip fence while the flat side of  
the board rests on the table. Since the work is pushed  
along the fence, it must have a straight edge and make  
solid contact with the table. The saw guard must  
always be used. The guard has anti-kickback fingers to  
help prevent kickback and a spreader to help prevent  
the saw kerf from closing and binding the blade.  
Start the motor and advance the work, holding it down  
against the fence. Never stand in the line of the saw cut  
when ripping. Hold the work with both hands and push it  
along the fence and into the saw blade as shown in Fig.  
33. After the workpiece is on the table the work can then  
Fig. 33  
be fed through the saw blade with one hand, as shown in  
Fig. 34. After the work is beyond the saw blade and anti-  
kickback fingers the feed can continue to the end of the  
table, after which the work is lifted and brought back  
along the outside edge of the fence. The cut-off stock  
remains on the table or tilts up slightly and is caught by  
the rear end of the guard or slides off the table to the  
floor. If the cut-off stock remains on the table it is not  
touched with the hands until the saw blade is stopped,  
unless it is a large piece allowing safe removal. When  
ripping boards longer than three feet, it is recommended  
that a work support be used at the rear of the saw to  
keep the workpiece from falling off the saw table.  
Fig. 34  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If the ripped work is less than 4 inches wide, a PUSH  
STICK should always be used to complete the feed, as  
shown in Fig. 35. The PUSH STICK can easily be made  
from scrap material as explained in the section  
“CONSTRUCTING PUSH STICK.” When ripping stock  
2 inches or narrower, assemble an auxiliary wood facing  
to the fence, as explained in the section “USING  
AUXILIARY WOOD FACING ON RIP FENCE” and use  
a PUSH STICK.  
USING AUXILIARY WOOD  
FACING ON RIP FENCE  
Fig. 35  
It is necessary when performing some special  
operations to add wood facing (A) Fig. 36, to one or both  
sides of the rip fence, as shown. The wood facing is  
attached to the fence with wood screws through the  
holes in the fence.  
A
A wood facing should be used when ripping material  
such as thin paneling to prevent the material from  
catching between the bottom of the rip fence and the  
saw table surface.  
Further information on the safe and proper operation of  
table saws is available in the Porter Cable/Delta “Getting  
the Most Out of Your Table Saw” How-To-Book, Catalog  
No. 11-400. Additional information on table saw safety is  
also available by writing to:  
Fig. 36  
NATIONAL SAFETY COUNCIL  
1121 Spring Lake Drive  
Itasca, IL 60143-3201  
USING ACCESSORY  
DADO HEAD  
DO NOT USE A “WOBBLE” DADO  
BLADE, OR A DADO BLADE LARGER THAN 6"  
DIAMETER.  
IMPORTANT: THE BLADE GUARD AND SPREADER  
ASSEMBLY CANNOT BE USED WHEN DADOING,  
AND MUST BE REMOVED.  
Fig. 37  
Dadoing is cutting a rabbet or wide groove into the work.  
Most dado head sets are made up of two outside saws  
and four or five inside cutters, as shown in Fig. 37.  
Various combinations of saws and cutters are used to cut  
grooves from 1/8" to 13/16" for use in shelving, making  
joints, tenoning, grooving, etc. The cutters are heavily  
swaged and must be arranged so that this heavy portion  
falls in the gullets of the outside saws, as shown in Fig.  
38. The saw and cutter overlap is shown in Fig. 39, (A)  
being the outside saw, (B) an inside cutter, and (C) a  
paper washer or washers which can be used as needed  
to control the exact width of groove. A 1/4" groove is cut  
by using the two outside saws. The teeth of the saws  
should be positioned so that the raker on one saw is  
beside the cutting teeth on the other saw.  
Fig. 38  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fig. 39  
Fig. 40  
The dado head set (D) Fig. 40, is assembled to the saw  
arbor as shown. IMPORTANT: The blade guard and  
splitter assembly cannot be used when dadoing and  
must be removed. Auxiliary jigs, fixtures, push sticks and  
feather boards should also be used. Also, the accessory  
dado head table insert Delta model 38122 (E) Fig. 40,  
must be used in place of the standard table insert.  
Fig. 41, shows a typical dado operation using the miter  
gage as a guide.  
NEVER USE THE DADO HEAD IN A  
BEVEL POSITION.  
ALWAYS INSTALL BLADE GUARD  
AFTER OPERATION IS COMPLETED.  
Fig. 41  
STORAGE  
For ease in storing and transporting, the saw can hold  
the following accessories as shown in Figs. 42 and 43.  
Fig. 42  
A
A - Wrenches  
B - Blade guard/Spreader assembly  
C - Fence  
D
D. - Extra Blade  
B
C
Fig. 42  
Fig. 43  
E - Miter gage  
F - Cord  
F
E
Fig. 43  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
CHANGING THE BLADE  
1.  
DISCONNECT MACHINE FROM  
POWER SOURCE. USE ONLY 10" DIAMETER SAW  
BLADES RATED FOR 4600 RPM OR HIGHER WITH  
5/8" ARBOR HOLES.  
2. Remove the table insert (A) Fig. 44, and raise the  
saw blade to its maximum height.  
A
3. Remove the blade guard and spreader assembly.  
NOTE: THE BLADE MUST BE IN THE 90 DEGREE  
POSITION TO THE TABLE FOR THE BLADE GUARD  
AND SPREADER ASSEMBLY TO BE REMOVED.  
Remove the table insert, pull out on the spreader release  
spring (A) Fig. 45, while pulling up on the blade  
guard/spreader assembly (B).  
Fig. 44  
B
4. Using the open end wrench (B) Fig. 46, place open  
end of wrench on flats on inside blade flange to keep the  
saw arbor from rotating and remove arbor nut (C) with  
the closed end of wrench (D). Turn nut (C)  
counterclockwise to remove. Remove outside blade  
flange (E) and saw blade (F).  
A
5. Install new blade, making certain teeth of blade are  
pointing down at the front of the saw table and  
assemble the outside blade flange (E) Fig. 46, and arbor  
nut (C). Tighten nut (C) with wrench (D) by turning nut  
clockwise while holding arbor steady with other wrench  
(B).  
Fig. 45  
D
B
6. Replace the table insert, blade guard and spreader  
assembly, and store the two wrenches.  
E
C
F
Fig. 46  
KEEP TOOL CLEAN  
Periodically blow out all air passages with dry compressed air. Clean all plastic parts with a soft damp cloth. NEVER use  
solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.  
WEAR SAFETY GLASSES WHILE USING COMPRESSED AIR.  
FAILURE TO START  
Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact with the outlet.  
Also, check for blown fuses or open circuit breakers in the line.  
BRUSH INSPECTION AND LUBRICATION  
For your continued safety and electrical protection, brush inspection and replacement on this tool should ONLY be  
performed by an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-CABLE SERVICE CENTER.  
At approximately 100 hours of use, take or send your tool to your nearest Authorized Porter-Cable Service Station to  
be thoroughly cleaned and inspected; worn parts replaced, when necessary, relubricated with fresh lubricant, if  
required; reassembled with new brushes; and performance tested.  
Any loss of power before the above maintenance check may indicate the need for immediate servicing of your tool.  
DO NOT CONTINUE TO OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is present, return  
your tool to the service station for immediate service.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND REPAIRS  
All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations,  
including brush inspection and replacement, should ONLY be performed by either an AUTHORIZED PORTER-CABLE  
SERVICE STATION or a PORTER-CABLEDELTA FACTORY SERVICE CENTER. All repairs made by these agencies are fully  
guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by anyone other  
than these agencies.  
Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all  
information shown on the nameplate of your tool (model number, type, serial number, etc.).  
ACCESSORIES  
A complete line of accessories is available from your Porter-CableDelta Supplier, Porter-CableDelta Factory Service  
Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.portercable.com for a catalog  
or for the name of your nearest supplier.  
Since accessories other than those offered by Porter-CableDelta have not been tested with  
this product, use of such accessories could be hazardous. For safest operation, only Porter-  
CableDelta recommended accessories should be used with this product.  
DO NOT USE A “WOBBLE” DADO BLADE, OR A DADO BLADE LARGER THAN 6" DIAMETER.  
CATALOG #  
38121  
DESCRIPTION  
Blade Insert  
38122  
12910  
12911  
12912  
Dado blade Insert  
10" Blade 24 teeth  
10" Blade 40 teeth  
10" Blade 60 teeth  
Folding Stand  
38129  
38239  
Outfeed Support  
CONSTRUCTING A FEATHERBOARD  
Fig. 47, illustrates dimensions for making a typical featherboard. The material which the featherboard is constructed  
of, should be a straight piece of wood that is free of knots and cracks. Featherboards are used to keep the work in  
contact with the fence and table and help prevent kickbacks. Clamp the featherboards to the fence and table so that  
the leading edge of the featherboards will support the workpiece until the cut is completed. Use featherboards for all  
non “thru-sawing” operations where the guard and spreader assembly must be removed (see Fig. 48). Always replace  
the guard and spreader assembly when the non thru-sawing operation is completed.  
Fig. 47  
Fig. 48  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONSTRUCTING A PUSH STICK  
When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily be  
made from scrap material by following the pattern shown.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PORTER-CABLE LIMITED  
ONE YEAR WARRANTY  
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original  
purchase. We will repair or replace at our option, any part or parts of the product and accessories  
covered under this warranty which, after examination, proves to be defective in workmanship or  
material during the warranty period. For repair or replacement return the complete tool or accessory,  
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.  
Proof of purchase may be required. This warranty does not apply to repair or replacement required  
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service  
Centers or Authorized Service Stations.  
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE  
OF PURCHASE.  
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,  
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING  
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY  
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL OR  
CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied warranty  
lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or  
exclusion may not apply to you.  
This warranty gives you specific legal rights and you may also have other legal rights which vary from  
state to state.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PORTER-CABLE • DELTA SERVICE CENTERS  
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)  
(CENTRE DE SERVICE PORTER-CABLE • DELTA)  
Parts and Repair Service for Porter-Cable  
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable  
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)  
Delta Power Tools are Available at These Locations  
Delta)  
Cleveland 44125  
ARIZONA  
MINNESOTA  
ILLINOIS  
8001 Sweet Valley Drive  
Unit #19  
Phone: (216) 447-9030  
Fax: (216) 447-3097  
Tempe 85282 (Phoenix)  
2400 West Southern Avenue  
Suite 105  
Phone: (602) 437-1200  
Fax: (602) 437-2200  
Minneapolis 55429  
Addison 60101 (Chicago)  
400 South Rohlwing Rd.  
Phone: (630) 424-8805  
Fax: (630) 424-8895  
5522 Lakeland Avenue North  
Phone: (763) 561-9080  
Fax: (763) 561-0653  
OREGON  
Portland 97230  
4916 NE 122 nd Ave.  
Phone: (503) 252-0107  
Fax: (503) 252-2123  
MISSOURI  
Woodridge 60517 (Chicago)  
2033 West 75th Street  
Phone: (630) 910-9200  
Fax: (630) 910-0360  
CALIFORNIA  
North Kansas City 64116  
1141 Swift Avenue  
Phone: (816) 221-2070  
Fax: (816) 221-2897  
Ontario 91761 (Los Angeles)  
3949A East Guasti Road  
Phone: (909) 390-5555  
Fax: (909) 390-5554  
San Leandro 94577 (Oakland)  
3039 Teagarden Street  
Phone: (510) 357-9762  
Fax: (510) 357-7939  
MARYLAND  
St. Louis 63119  
Elkridge 21075 (Baltimore)  
7397-102 Washington Blvd.  
Phone: (410) 799-9394  
Fax: (410) 799-9398  
7574 Watson Road  
Phone: (314) 968-8950  
Fax: (314) 968-2790  
PENNSYLVANIA  
Willow Grove 19090  
520 North York Road  
Phone: (215) 658-1430  
Fax: (215) 658-1433  
NEW YORK  
MASSACHUSETTS  
Braintree 02185 (Boston)  
719 Granite Street  
Phone: (781) 848-9810  
Fax: (781) 848-6759  
COLORADO  
Flushing 11365-1595 (N.Y.C.)  
175-25 Horace Harding Expwy.  
Phone: (718) 225-2040  
Fax: (718) 423-9619  
Arvada 80003 (Denver)  
8175 Sheridan Blvd., Unit S  
Phone: (303) 487-1809  
Fax: (303) 487-1868  
TEXAS  
Carrollton 75006 (Dallas)  
1300 Interstate 35 N, Suite 112  
Phone: (972) 446-2996  
Fax: (972) 446-8157  
NORTH CAROLINA  
Charlotte 28270  
9129 Monroe Road, Suite 115  
Phone: (704) 841-1176  
Fax: (704) 708-4625  
Franklin 02038 (Boston)  
Franklin Industrial Park  
101E Constitution Blvd.  
Phone: (508) 520-8802  
Fax: (508) 528-8089  
FLORIDA  
Davie 33314 (Miami)  
4343 South State Rd. 7 (441)  
Unit #107  
Phone: (954) 321-6635  
Fax: (954) 321-6638  
Tampa 33609  
4538 W. Kennedy Boulevard  
Phone: (813) 877-9585  
Fax: (813) 289-7948  
Houston 77038  
4321 Sam Houston Parkway, West  
Suite 180  
Phone: (281) 260-8887  
Fax: (281) 260-9989  
OHIO  
MICHIGAN  
Columbus 43214  
4560 Indianola Avenue  
Phone: (614) 263-0929  
Fax: (614) 263-1238  
Madison Heights 48071 (Detroit)  
30475 Stephenson Highway  
Phone: (248) 597-5000  
Fax: (248) 597-5004  
WASHINGTON  
Auburn 98001(Seattle)  
3320 West Valley HWY, North  
Building D, Suite 111  
Phone: (253) 333-8353  
Fax: (253) 333-9613  
GEORGIA  
Forest Park 30297 (Atlanta)  
5442 Frontage Road,  
Suite 112  
Phone: (404) 608-0006  
Fax: (404) 608-1123  
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and  
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service Center,  
or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to the  
nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades. Llame  
al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-Cable  
Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable  
Delta, Centro de Servicio Autorizado o Centro de  
Servicio de Fábrica Porter-Cable  
Servicio de Fábrica Porter-Cable  
Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de  
Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au  
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-  
Cable  
Delta, s’adresser à tout distributeur Porter-Cable  
Delta, centre de service agréé ou centre de service d’usine Porter-Cable  
Delta. Si  
Delta le  
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable  
plus proche.  
CANADIAN PORTER-CABLE DELTA SERVICE CENTERS  
QUÉBEC  
ALBERTA  
MANITOBA  
1515 Ave.  
Bay 6, 2520-23rd St. N.E.  
Calgary, Alberta  
T2E 8L2  
1699 Dublin Avenue  
Winnipeg, Manitoba  
R3H 0H2  
St-Jean Baptiste, Suite 180  
Québec, Québec  
G2E 5E2  
Phone: (418) 877-7112  
Fax: (418) 877-7123  
Phone: (403) 735-6166  
Fax: (403) 735-6144  
Phone: (204) 633-9259  
Fax: (204) 632-1976  
BRITISH COLUMBIA  
8520 Baxter Place  
Burnaby, B.C.  
V5A 4T8  
Phone: (604) 420-0102  
Fax: (604) 420-3522  
ONTARIO  
1447, Begin  
St-Laurent, (Montréal), Québec  
H4R 1V8  
Phone: (514) 336-8772  
Fax: (514) 336-3505  
505 Southgate Drive  
Guelph, Ontario  
N1H 6M7  
Phone: (519) 767-4132  
Fax: (519) 767-4131  
The following are trademarks of PORTER-CABLE  
DELTA (Las siguientes son marcas registradas de PORTER-CABLE  
DELTA S.A.) (Les  
marques suivantes sont des marques de fabriquant de la PORTER-CABLE  
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,  
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying  
Chips™, FRAME SAW®, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-  
Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design),  
PORTER-CABLE®PROFESSIONAL POWER TOOLS, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®,  
QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™,  
Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber  
Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,  
TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®,  
Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®, WOODWORKER’S CHOICE™.  
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.  
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden  
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et  
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.  
Printed in U.S.A. PC-0603-150  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips Camera Accessories A76 User Manual
Philips Dehumidifier AS650 User Manual
Philips Home Theater System DCK3060 User Manual
Pioneer Model Vehicle TS W253R User Manual
Pioneer Stereo Amplifier GM 3100T User Manual
Planar Car Video System PE170 User Manual
Planet Technology Network Card WDAP 2000PE User Manual
Planet Technology Switch WSW 2401A User Manual
Poulan Tiller PRRT875X User Manual
Printek Printer FormsMaster 8000se Series User Manual