Instruction
manual
ESPAÑOL: PÁGINA 21
FRANÇAIS: PAGE 43
8.5 Horsepower
3000 PSI
3 GPM
Pressure Washer
PCK3030SP
IMPORTANT
Please make certain that the person who
is to use this equipment carefully reads
and understands these instructions before
starting operations.
To learn more about Porter-Cable
visit our website at:
The Model and Serial No. plate is located on the frame.
Record these numbers in the spaces below and retain for
future reference.
Model No.
Type
Serial No.
Copyright © 2003 Porter-Cable Corporation
Part No. D27927-034-0
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Read Operators Manual. Do not operate equipment until you
have read operators Manual for Safety, Assembly, Operation, and
Maintenance Instructions.
READ AND SAVE THESE INSTRUCTIONS
HAZARD
RISK OF EXPLOSION OR FIRE
WHAT CAN HAPPEN
HOW TO PREVENT IT
• Spilled gasoline and it’s vapors can be-
come ignited from cigarette sparks,
electrical arcing, exhaust gases, and hot
engine components such as the muffler.
• Shut off engine and allow it to cool before
adding fuel to the tank.
• Use care in filling tank to avoid spilling fuel.
Move pressure washer away from fueling area
before starting engine.
• Heat will expand fuel in the tank which
could result in spillage and possible fire
explosion.
• Keep maximum fuel level ½” below top of
tank to allow for expansion.
• Operating the pressure washer in an ex-
plosive environment could result in a fire.
• Operate and fuel equipment in well ventilated
areas free from obstructions. Equip areas with
fire extinguisher suitable for gasoline fires.
• Materials placed against or near the pres-
sure washer can interfere with its proper
ventilation features causing overheating
and possible ignition of the materials.
• Never operate pressure washer in an area
containing dry brush or weeds.
• Muffler exhaust heat can damage painted
surfaces, melt any material sensitive to
heat (such as siding, plastic, rubber, or
vinyl), and damage live plants.
• Always keep pressure washer a minimum of
four feet away from surfaces (such as houses,
automobiles, or live plants) that could be dam-
aged from muffler exhaust heat.
• Improperly stored fuel could lead to acci-
dental ignition. Fuel improperly secured
could get into the hands of children or
other unqualified persons.
• Store fuel in an OSHA approved container,
in a secure location away from work area.
• Use of acids, toxic or corrosive chemicals,
poisons, insecticides, or any kind of flam-
mable solvent with this product could re-
sult in serious injury or death.
• Do not spray flammable liquids.
HAZARD
RISK TO BREATHING
WHAT CAN HAPPEN
HOW TO PREVENT IT
• Operate pressure washer in a well ventilated
area. Avoid enclosed areas such as garages,
basements, etc.
• Breathing exhaust fumes will cause serious
injury or death!
• Never operate unit in a location occupied by
humans or animals.
• Some cleaning fluids contain substances
which could cause injury to skin, eyes, or
lungs.
• Use only cleaning fluids specifically recom-
mended for high pressure washers. Follow
manufacturers recommendations. Do not
use chlorine bleach or any other corrosive
compound.
3- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
HAZARD
RISK OF INJURY OR PROPERTY DAMAGE
WHEN TRANSPORTING OR STORING
WHAT CAN HAPPEN
HOW TO PREVENT IT
• Fuel or oil can leak or spill and could
result in fire or breathing hazard, serious
injury or death can result. Fuel or oil leaks
will damage carpet, paint or other
surfaces in vehicles or trailers.
• If pressure washer is equipped with a fuel
shut-off valve, turn the valve to the off
position before transporting to avoid fuel
leaks. If pressure washer is not equipped
with a fuel shut-off valve, drain the fuel from
tank before transporting. Only transport fuel
in an OSHA approved container. Always
place pressure washer on a protective mat
when transporting to protect against dam-
age to vehicle from leaks. Remove pressure
washer from vehicle immediately upon arrival
at your destination.
HAZARD
RISK TO FLUID
INJECTION
WHAT CAN HAPPEN
HOW TO PREVENT IT
• Your washer operates at fluid pressures
and velocities high enough to penetrate
human and animal flesh, which could
result in amputation or other serious injury.
Leaks caused by loose fittings or worn or
damaged hoses can result in injection
injuries. DO NOT TREAT FLUID
• Never place hands in front of nozzle.
• Direct spray away from self and others.
• Make sure hose and fittings are tightened
and in good condition. Never hold onto the
hose or fittings during operation.
• Do not allow hose to contact muffler.
• Never attach or remove wand or hose
fittings while system is pressurized.
INJECTION AS A SIMPLE CUT! See a
physician immediately!
• Injuries can result if system pressure is not
reduced before attempting maintenance or
disassembly.
• To relieve system pressure, shut off engine,
turn off water supply, and pull gun trigger
until water stops flowing.
• Use only hoses and accessories rated for
pressure higher than your pressure
washer's p.s.i.
HAZARD
RISK OF CHEMICAL BURN
WHAT CAN HAPPEN
HOW TO PREVENT IT
• Use of acids, toxic or corrosive chemicals,
poisons, insecticides, or any kind of flam-
mable solvent with this product could re-
sult in serious injury or death.
• Do not use acids, gasoline, kerosene, or
any other flammable materials in this
product. Use only household detergents,
cleaners and degreasers recommended for
use in pressure washers.
• Wear protective clothing to protect eyes
and skin from contact with sprayed
materials.
4- ENG
Download from Www.Somanuals.com. All Manuals Search And Download.
D27927
HAZARD
RISK OF UNSAFE OPERATION
WHAT CAN HAPPEN
HOW TO PREVENT IT
• Unsafe operation of your pressure washer
could lead to serious injury or death to
you or others.
• Do not use chlorine bleach or any other
corrosive compound.
• Become familiar with the operation and con-
trols of the pressure washer.
• Keep operating area clear of all persons,
pets, and obstacles.
• Do not operate the product when fatigued
or under the influence of alcohol or drugs.
Stay alert at all times.
• Never defeat the safety features of this
product.
• Do not operate machine with missing,
broken, or unauthorized parts.
• Never leave wand unattended while unit is
running.
• If proper starting procedure is not
followed, engine can kickback causing
serious hand and arm injury.
• If engine does not start after two pulls,
squeeze trigger of gun to relieve pump
pressure. Pull starter cord slowly until
resistance is felt. Then pull cord rapidly
to avoid kickback and prevent hand or
arm injury.
• Keep children away from the pressure
washer at all times.
• The spray gun/wand is a powerful clean-
ing tool that could look like a toy to a
child.
• Reactive force of spray will cause
gun/wand to move, and could cause the
operator to slip or fall, or misdirect the
spray. Improper control of gun/wand can
result in injuries to self and others.
• Do not overreach or stand on an unstable
support. Grip gun/wand firmly with both
hands. Expect the gun to kick when trig-
gered.
HAZARD
RISK OF ELECTRICAL SHOCK
WHAT CAN HAPPEN
HOW TO PREVENT IT
• Spray directed at electrical outlets or
switches, or objects connected to an
electrical circuit, could result in a fatal
electrical shock.
• Unplug any electrically operated product
before attempting to clean it. Direct spray
away from electric outlets and switches.
HAZARD
RISK OF HOT SURFACES
WHAT CAN HAPPEN
HOW TO PREVENT IT
• Contact with hot surfaces, such as
engines exhaust components, could
result in serious burn.
• During operation, touch only the control
surfaces of the pressure washer. Keep
children away from the pressure washer at all
times. They may not be able to recognize the
hazards of this product.
5- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
HAZARD
RISK OF INJURY FROM SPRAY
WHAT CAN HAPPEN
HOW TO PREVENT IT
• Always wear ANSI approved Z87 safety
glasses.Wear protective clothing to protect
against accidental spraying.
• Never point wand at, or spray people or
animals.
• Always secure trigger lock when wand is not
in service to prevent accidental operation.
• Never permanently secure trigger in pull
back (open) position.
• High velocity fluid spray can cause
objects to break, propelling particles at
high speed.
• Light or unsecured objects can become
hazardous projectiles.
The powerful spray from your pressure washer is capable of causing
damage to surfaces such as wood, glass, automobile paint, auto
striping and trim, and delicate objects such as flowers and shrubs. Before spraying,
check the item to be cleaned to assure yourself that it is strong enough to resist damage
from the force of the spray. Avoid the use of the concentrated spray stream except for
very strong surfaces like concrete and steel.
Operating without flow of water will result in equipment damage. Operating the pressure
washer with water supply shutoff will void your warranty. You should never run this pres-
sure washer for more than 2 minutes without pulling the trigger to allow cool water to
enter the pump and the heated (recirculated) water to exit.
CONSUMER GENERAL AND SERVICE INFORMATION
DO NOT RETURN THIS PRODUCT TO THE RETAILER!
FOR SERVICE OPTIONS CALL: 1-888-559-8550
• Congratulations! You have purchased a high quality product from America’s leading
manufacturer of pressure washers. This pressure washer, when properly used and
maintained, will provide trouble free service. Please read and follow these instructions for
proper use and maintenance.
• All sales of pressure washers are final. Do not return this product to the retailer.
• If you experience any problems and need assistance, please call us at our toll free
number 1-888-559-8550, Monday through Saturday.
• If repair or service part purchase is required, our many Authorized Warranty Service
Centers are conveniently located and equipped to handle all in-warranty and out-of-
warranty service.
• For the location of the nearest Authorized Warranty Service Center call 1-888-559-8550,
• All pressure washers carry a manufacturer's one year warranty from date of purchase for
consumer use and a 90 day warranty for commercial use.
• Retain sales receipt as proof of purchase for warranty service.
• Read and understand all safety warnings.
• Do not operate this unit until you have read and understand this Owners Manual for
Safety, Operation, and Maintenance Instructions.
• Do not operate this unit until you have read and understand the Engine Owners Manual
for Safety, Operation, and Maintenance Instructions.
6- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
CARTON CONTENTS
English/
Spanish/
French
Operator’s
Manual
Handle
Engine
Manual
Engine Oil
Bagged Handle
Engine Frame and
Wheel Assembly
Knobs
Saddle
Bolts
Chemical
Hose
Grommet Kit
with Quick
Connect
Nozzles
Nozzle Cleaning
Kit
High Pressure Hose
Bagged Parts
Quick Connect Spray Wand
Spray Gun
7- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
1. Place handle assembly onto frame and connect handle to frame.
2. Attach high pressure hose to gun. Tighten securely.
3. Connect spray wand to gun. Tighten securely.
4. To Assemble Quick Connect Grommets:
a. Squeeze grommet and place into hole, fitting groove to rim.
8- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
b. Push grommet into place.
c. Repeat steps until all grommets are assembled.
5. To Assemble Quick Connect Nozzles:
a. Remove five colored quick connect nozzles from plastic bag and insert
them into correct grommet. NOTE: Nozzles are color coded to match
colored nozzles on panel.
6. Add engine oil (supplied) to engine. Refer to Engine Owners Manual supplied
by engine manufacturer for correct procedure.
NOTE: There will be a slight amount of oil in the engine from factory testing.
NOTE: The high pressure pump was filled with oil at the factory. There is no need
to add oil at this time, see the Maintenance section of this manual for
Maintenance information.
The shipping plug must be removed and replaced with the
dipstick/oil plug before operating pressure washer.
7. Using a 17 mm wrench, remove shipping plug from
pump by turning it counterclockwise. Discard plug.
8. Remove dipstick/oil plug from plastic bag and install
into pump, tighten securely.
9- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
READ THIS OPERATION MANUAL AND SAFETY RULES BEFORE OPERATING
YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with
the location of various controls and adjustments. Save this manual for future
reference.
Spray
Gun
High
Pressure
Hose
Engine
Quick
Connect
Spray Wand
High
Pressure
Pump
BASIC ELEMENTS OF A PRESSURE WASHER
High Pressure Pump: Increases the pressure of the water supply.
Engine: Drives the high pressure pump.
High Pressure Hose: Carries the pressurized water from the pump to the gun
and spray wand.
Spray Gun: Connects with spray wand to control water flow rate, direction, and
pressure.
Quick Connect Spray Wand: Spray wand is equipped with a female quick
connect coupler on the end. This allows the user to quickly change out high-pres-
sure nozzles for different spray patterns and change to the soap nozzle for low
pressure and chemical/soap applications. See How To Use Spray wand paragraph
in this section.
Chemical Hose (not shown): Feeds cleaning agents into the pump to mix with
the pressurized water. See How To Apply Chemicals/Cleaning Solvents in
Operation section of this manual.
BASIC ELEMENTS OF ENGINE
Refer to the engine manual for location and operation of engine controls.
Choke Control: Opens and closes carburetor choke valve
Throttle Control Lever: Controls engine speed.
Starter Grip: Pulling starter grip operates recoil starter to crank engine.
Fuel Valve Lever: Opens/closes connection between fuel tank and carburetor.
Engine Switch: Enables and disables ignition system.
10- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESSURE WASHER TERMINOLOGY
PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used
for air pressure, hydraulic pressure, etc.
GPM: Gallons Per Minute. The unit of measure for the flow rate of water.
CU: Cleaning Units. GPM multiplied by PSI.
Bypass Mode: In Bypass Mode, the pump is recirculating water because the
trigger of the spray gun is not pulled. If unit is left in bypass mode for more than
two (2) minutes, the water temperature will rise to a dangerous level and could
damage internal components of the pump. Any damage to pump due to these
causes will not be covered under warranty.
DO NOT allow your unit to operate in bypass mode for more
than two minutes at any time. Overheating of pump can
cause damage to pump.
Thermal Relief Valve: In an effort to prevent extreme damage, pumps are
equipped with a thermal relief valve. This valve will open when the temperature
inside the pump rises too high. This valve will then release a gush
Thermal
Relief
Valve
of water in an effort to lower the temperature inside the pump.
Immediately after this occurs, the valve will close.
Chemical Injection System: Mixes cleaners or cleaning solvents
with the pressurized water to improve cleaning effectiveness.
Water Supply: All pressure washers must have a source of water.
The minimum requirements for a water supply are 20 PSI and 5
gallons per minute.
PRESSURE WASHER OPERATING FEATURES
PRESSURE ADJUSTMENTS
The pressure setting is preset at the factory to achieve optimum pressure and
cleaning. If you need to lower the pressure, it can be accomplished by these
methods.
1. Back away from the surface to be cleaned. The further away you are, the
less the pressure will be on the surface to be cleaned.
2. Change to the 40º nozzle - white, this nozzle delivers a less powerful
stream of water and a wider spray pattern.
DO NOT attempt to increase pump pressure. A higher
pressure setting than the factory set pressure may damage
pump.
3. Adjust the pressure regulator on the pump. Turn
the pressure regulator knob counterclockwise to
lower pressure. Refer to the illustrations to identify
your pressure regulator. Once you have finished
using your pressure washer, return the pressure regu-
lator to its original position by turning it clockwise.
Pressure
Regulator
Knob
DO NOT try to turn pressure regulator
knob past the built-in stop or damage
to pump will result.
11- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
TO USE SPRAY WAND
Your pressure washer is equipped with five spray nozzles. Each nozzle is color
coded and delivers a specific spray pattern for a particular cleaning purpose.
The size of the nozzle determines the size of the fan spray and the pressure out
of the nozzle. The 0º, 15º, 25º, and 40º nozzles are high pressure nozzles. The
chemical nozzle is a low pressure nozzle.
The nozzles are housed in receptacles on the panel of the pressure washer
handle. Colors on the panel identify nozzle location and spray pattern.
Risk of injection or injury to person. Do not direct discharge
stream toward persons, unprotected skin, eyes, or any pets
or animals. Serious injury can occur.
Changing Nozzles
DO NOT attempt to change nozzles
while pressure washer is running.
Turn engine off before changing nozzles.
1. Pull quick connect coupler back and insert nozzle.
2. Release quick connect coupler and twist nozzle to
make sure it is secure in coupler.
Risk Of Injury. Ensure nozzle is
completely inserted in QC socket, and
QC snap ring is fully engaged (forward) before
squeezing gun trigger.
0º nozzle - Red. This nozzle delivers a pinpoint
stream and is extremely powerful. It covers a very
small area of cleaning. This nozzle should only be
used on surfaces that can withstand this high
pressure such as metal or concrete. Do not use on
wood.
15º nozzle - Yellow. This nozzle delivers a powerful
15 degree spray pattern for intense cleaning of small
areas. This nozzle should only be used on areas that
can withstand the high pressure from this nozzle.
25º nozzle - Green. This nozzle delivers a 25
degree spray pattern for intense cleaning of larger
areas. This nozzle should only be used on areas that
can withstand the pressure from this nozzle.
40º nozzle - White. This nozzle delivers a 40 degree
spray pattern and a less powerful stream of water. It
covers a wide area of cleaning. This nozzle should
be used for most general cleaning jobs.
Chemical nozzle - Black. This nozzle is used to
apply chemicals or cleaning solutions. It has the
least powerful stream.
12- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO APPLY CHEMICALS AND CLEANING SOLVENTS
Applying chemicals or cleaning solvents is a low pressure operation. NOTE: Use
only soaps and chemicals designed for pressure washer use. Do not use bleach.
To Apply chemicals:
1. Press chemical hose onto barbed fitting located near
Barbed
Fitting
high pressure hose connection of pump as shown.
2. Place other end of chemical hose with filter on it into
container holding chemical/cleaning solution. NOTE:
The chemical/water ratio is 7:1, for every 7 gallons of
water pumped 1 gallon of chemical/cleaning solution
will be used.
3. Install low pressure (black) nozzle into quick
connect fitting of spray wand, see How To Use Spray
Wand paragraph in this section.
4. After use of chemicals, place chemical hose into container of clean water and
draw clean water through chemical injection system to rinse system thoroughly.
If chemicals remain in the pump it could be damaged. Pumps damaged due to
chemicals will not be covered under warranty.
NOTE: Chemicals and soaps will not siphon when spray wand is in the high pressure
setting.
READ AND UNDERSTAND ALL WARNINGS BEFORE STARTING UNIT
When using the high pressure setting, DO NOT allow the
high pressure spray to come in contact with unprotected skin,
eyes, or with any pets or animals. Serious injury can occur.
Your washer operates at fluid pressures and velocities high enough to penetrate
human and animal flesh, which could result in amputation or other serious injury.
Leaks caused by loose fittings or worn or damaged hoses can result in injection
injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a
physician immediately!
NEVER fill fuel tank when engine is running or hot. Do not
smoke when filling fuel tank.
NEVER fill fuel tank completely. Fill tank to 1/2" below bottom of filler neck to
provide space for fuel expansion. Wipe any fuel spillage from engine and
equipment before starting engine.
NEVER run engine indoors or in enclosed, poorly ventilated areas. Engine
exhaust contains carbon monoxide, an odorless and deadly gas.
DO NOT let hoses come in contact with very hot engine muffler during or
immediately after use of your pressure washer. Damage to hoses from contact
with hot engine surfaces will NOT be covered by warranty.
NEVER pull water supply hose to move pressure washer. This
could damage hose and/or pump inlet.
DO NOT use hot water, use cold water only.
NEVER turn water supply off while pressure washer engine is running or
damage to pump will result.
DO NOT stop spraying water for more than two minutes at a time. Pump
operates in bypass mode when spray gun trigger is not pressed. If pump is left
in bypass mode for more than two minutes internal components of the pump
can be damaged.
If you do not understand these precautions, please call 1-888-559-8550 to
speak to a service representative for further instructions.
13- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING
Prior to starting, refer to your engine manual for proper starting procedures
for your engine type.
1. In a well ventilated outdoor area add fresh, high quality, unleaded gasoline
with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled
fuel before starting the engine. Refer to Engine Owners Manual for correct
procedure.
2. Check engine oil level. See Engine Owners Manual for correct procedure.
NOTE: There will be a slight amount of oil in the engine from factory
testing.
3. Verify the filter screen is in water inlet of pump.
Filter Screen
NOTE: Cone side faces out.
4. Connect water source to pump inlet.
NOTE: Water source must provide a minimum of 5 gallons
per minute at 20 p.s.i.
5. Connect high pressure hose to pump outlet.
6. If applying a chemical or cleaning solution, see
How To Apply Chemicals/Cleaning Solvents in
Operation section of this manual.
High Pressure Hose
7. Turn water source on. NOTE: Failure to do so could
cause damage to the pump.
8. Start engine. See Engine Owners Manual for correct
procedure. NOTE: If the engine does not start after
two pulls, pull the trigger to relieve the pressure.
Water
Source
9. Depress trigger on gun to start water flow. NOTE:
Stand on a stable surface and grip gun/spray wand
firmly with both hands. Expect the gun to kick when triggered.
10. Release trigger to stop water flow.
11. Adjust spray for the task being performed by changing quick connect
nozzle. See How To Use Spray Wand instructions in this section.
SHUTTING DOWN
1. After each use, if you have applied chemicals, place chemical hose into
container of clean water and draw clean water through chemical injection system
to rinse system thoroughly. NOTE: Failure to do so could cause damage to the
pump.
2. Turn engine off. See Engine Owner’s Manual. NOTE: NEVER turn the water
off with the engine running.
3. Turn water source off.
4. Pull trigger on spray gun to relieve any water pressure in hose or spray gun.
5. See Storage section in this manual for proper storage procedures.
14- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
When performing maintenance, you may be exposed to hot
surfaces, water pressure, or moving parts that can cause
serious injury or death!
Before performing any maintenance or repair, disconnect spark plug wire, let
engine cool and release all water pressure. The engine contains flammable
fuel. DO NOT smoke or work near open flames while performing
maintenance.
To ensure efficient operation and longer life of your pressure washer, a routine
maintenance schedule should be prepared and followed. If the pressure washer is
used in unusual conditions, such as high-temperatures or dusty conditions, more
frequent maintenance checks will be required.
ENGINE
Consult the Engine Owners Manual for the manufacturer's recommendations for
any and all maintenance.
PUMP
NOTE: The pump was filled with oil at the factory.
1. Change pump oil after the first ten (10) hours of operation and every fifty (50)
hours thereafter.
To Check Oil:
1. Remove dipstick/oil plug from pump and
wipe clean.
Dipstick/oil plug
2. Insert dipstick/oil plug fully into pump,
then remove it.
3. Oil level is correct when oil covers the
lower 1/2 inch of end of dipstick/oil plug.
Oil
Drain
Plug
How To Change Pump Oil
1. Loosen dipstick/oil plug.
2. Place a container under the oil drain plug.
3. Remove oil drain plug.
4. After oil is drained replace oil drain plug. Tighten securely.
5. Remove dipstick/oil plug and fill with recommended oil. See the Pump Oil
Chart for the correct amount and type of oil.
6. Replace dipstick/oil plug and tighten securely.
PUMP OIL CHART
OIL
CAPACITY
PUMP TYPE
OIL TYPE
30W non detergent
Annovi Reverberi (XMV)
13.5 oz.
15- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
NOZZLE CLEANING
If the nozzle becomes clogged with foreign materials, such as dirt, excessive
pressure may develop. If the nozzle becomes partially clogged or restricted, the
pump pressure will pulsate. Clean the nozzle immediately using the nozzle kit
supplied and the following instructions:
1. Shut off the pressure washer and turn off the water supply.
2. Disconnect spark plug wire.
3. Pull trigger on gun handle to relieve any water pressure.
4. Disconnect the spray wand from the gun.
5. Remove the high-pressure nozzle from the spray wand. Remove any
obstructions with the nozzle cleaning tool provided and backflush with clean
water.
6. Direct water supply into spray wand to backflush loosened particles for 30
seconds.
7. Reassemble the nozzle to the wand.
8. Reconnect spray wand to gun and turn on water supply.
9. Start pressure washer and place spray wand into high pressure setting to test.
HOW TO CLEAN THE WATER INLET FILTER
This screen filter should be checked periodically and cleaned if necessary.
1. Remove filter by grasping end and removing it from
Filter Screen
water inlet of pump as shown.
2. Clean filter by flushing it with water on both sides.
3. Re-insert filter into water inlet of pump. NOTE: Cone
side faces out.
NOTE: Do not operate pressure washer without filter properly
installed.
16- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
ENGINE
Consult the Engine Owners Manual for the manufacturer's recommendations for
storage.
PUMP
1. Drain all water from high pressure hose, coil it, and store it in cradle of the
pressure washer handle.
2. Drain all water from spray gun and spray wand by holding spray gun in a
vertical position with nozzle end pointing down and squeezing trigger. Store
in gun/hose holder.
3. Store chemical hose, high pressure hose, spray gun, and spray wand so
they are protected from damage, such as being run over.
It is recommended that you follow these steps to protect the internal seals of the
pressure washer when STORING THE UNIT FOR MORE THAN 30 DAYS AND/OR
WHEN FREEZING TEMPERATURES ARE EXPECTED.
*RV antifreeze needs to be run through the pump as outlined in the steps below.
4. Obtain a funnel, six ounces of *RV antifreeze, and approximately 36 inches
of garden hose with a male hose connector attached to one end.
Use only RV antifreeze. Any other antifreeze is corrosive and
can damage pump.
5. Disconnect spark plug wire.
6. Connect 36 inch length of hose to
water inlet of pump.
7. Add *RV antifreeze to hose as
shown.
8. Pull engine starter rope slowly
several times until antifreeze comes
out of high pressure hose connection
of pump.
9. Remove short hose from water inlet
of pump.
10. Reconnect spark plug wire.
*Windshield washer fluid may also be used
17- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING GUIDE
CAUSE
CORRECTION
PROBLEM
Add Fuel.
No fuel.
Low oil
Engine will not
start (see Engine
Manual for
further engine
troubleshooting)
Add required amount of oil.
Squeeze gun trigger to relieve
pressure.
Pressure builds up after two pulls
on the recoil starter or after initial
use.
Move choke to the “Choke”
position.
Choke lever in the “No Choke”
position.
Attach spark plug wire.
Spark plug wire not attached.
Place engine ON/OFF switch in
on position.
Engine ON/OFF switch in OFF
position
Choke lever in the “Choke”
position on a “hot” engine or an
engine that has been exposed to
thermal heat for a long period of
time.
Move choke to the “No Choke”
position.
Fuel valve closed
Move the fuel valve lever to the
“Open” position.
No or low
pressure
(initial use)
Spray wand not in high pressure.
See How to Use Spray Wand
paragraph in the Operation
Section.
Low water supply.
Water supply must be at least 5
GPM @ 20 PSI.
Leak at high pressure hose fitting.
Nozzle obstructed.
Repair leak. Apply sealant tape
if necessary.
See Nozzle Cleaning paragraph in
the Maintenance section for the
correct procedure.
Water filter screen clogged.
Defective E-Z start valve.
Remove and clean filter.
Check with Authorized Warranty
Service Center (AWSC.)
Turn off the engine, then the
water source. Disconnect the
water source from the pump inlet
and turn the water source on to
remove all air from the hose.
When there is a steady stream of
water present, turn water source
off. Re-connect water source to
pump inlet and turn on water
source. Squeeze trigger to re-
move remaining air
Air in hose.
Choke lever in the “Choke” position. Move choke to the “No Choke”
position.
Throttle control lever is not in the
“Fast” position.
Move throttle control lever to the
“Fast” position.
High pressure hose is too long.
Use high pressure hose under
100 feet.
18- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUSE
CORRECTION
PROBLEM
See How to Use Spray Wand
paragraph in the Operation
Section.
Spray wand not in low pressure.
Will not draw
chemicals
Chemical filter clogged.
Clean filter.
Insure end of chemical hose is
fully submerged into chemical.
Chemical screen not in chemical
Chemical too thick.
Dilute chemical. Chemical should
be the same consistency as
water.
Lengthen water supply hose
instead of high pressure hose.
Pressure hose is too long
Chemical build up in chemical
injector.
Have parts cleaned or replaced
by AWSC.
Worn seal or packing
Worn or obstructed valves.
Worn unloader piston.
Worn E-Z start valve.
Have replaced by AWSC.
Have replaced by AWSC.
Have replaced by AWSC.
Have replaced by AWSC.
No or low
pressure
(after period of
normal use)
Worn or broken o-ring.
Loose hose connection.
Check and replace.
Tighten.
Water leaking at
gun/spray wand
connection
Water leaking
at pump
Tighten.
Loose connections.
Piston packings worn.
Have replaced by AWSC.
Worn or broken o-rings.
Have replaced by AWSC.
Have replaced by AWSC.
Pump head or tubes damaged
from freezing.
Oil leaking at
pump
Oil seals worn.
Have replaced by AWSC
Tighten.
Loose drain plug.
Worn drain plug, o-ring
Worn fill plug o-ring.
Pump overfilled.
Check and replace.
Check and replace.
Check for correct amount.
Drain and fill with correct amount
and type of oil.
Incorrect oil used.
Vent plug is clogged.
Clean vent plug; blow air through it
to remove any blockage. If prob-
lem persists, replace plug.
Nozzle obstructed.
Pump Pulsates
See Nozzle Cleaning paragraph in
the Maintenance section for the
correct procedure.
19- ENG
Download from Www.Somanuals.com. All Manuals Search And Download.
D27927
LIMITED WARRANTY
PORTER-CABLE CORPORATION warrants to the original purchaser that all products covered under this
warranty are free from defects in material and workmanship. Products covered under this warranty include air
compressors, air tools, service parts, pressure washers, and generators, which have the following warranty
periods:
3 YEARS - Limited warranty on 2-stage oil-free air compressor pumps that operate at 1725 RPM.
2 YEARS - Limited warranty on oil-lubricated air compressor pumps.
1 YEAR - Limited warranty on all other air compressor components.
2 YEARS - Limited warranty on electric generator alternators.
1 YEAR - Limited warranty on other generator components.
2 YEARS - Limited warranty on pneumatic air tools as described in Porter-Cable general catalog.
1 YEAR - Limited warranty on pressure washers used in consumer applications (i.e. personal residential
household usage only).
90 DAY - Pressure washers used for commercial applications (income producing) and service parts.
1 YEAR - Limited warranty on all accessories.
Porter-Cable will repair or replace, at Porter-Cable's option, products or components which have failed within
the warranty period. Service will be scheduled according to the normal work flow and business hours at
the service center location, and the availability of replacement parts. All decisions of Porter-Cable
Corporation with regard to this limited warranty shall be final.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
RESPONSIBILITY OF ORIGINAL PURCHASER (initial User):
•
To process a warranty claim on this product, DO NOT return it to the retailer. The product must be evaluated
by an Porter-Cable Authorized Warranty Service Center. For the location of the nearest Porter-Cable
Authorized Warranty Service Center call 1-888-559-8550, 24 hours a day, 7 days a week.
Retain original cash register sales receipt as proof of purchase for warranty work.
Use reasonable care in the operation and maintenance of the product as described in the Owners Manual(s).
Deliver or ship the product to the nearest Porter-Cable Authorized Warranty Service Center. Freight costs, if
any, must be paid by the purchaser.
•
•
•
•
•
Air compressors with 60 and 80 gallon tanks will be inspected at the site of installation. Contact the nearest
Porter-Cable Authorized Warranty Service Center that provides on-site service calls, for service call
arrangements.
If the purchaser does not receive satisfactory results from the Porter-Cable Authorized Warranty Service
Center, the purchaser should contact Porter-Cable.
THIS WARRANTY DOES NOT COVER:
•
•
Merchandise sold as reconditioned, used as rental equipment, and floor or display models.
Merchandise that has become damaged or inoperative because of ordinary wear, misuse*, cold, heat, rain,
excessive humidity, freeze damage, use of improper chemicals, negligence, accident, failure to operate the
product in accordance with the instructions provided in the Owners Manual(s) supplied with the product,
improper maintenance, the use of accessories or attachments not recommended by Porter-Cable, or
unauthorized repair or alterations.
*
An air compressor that pumps air more than 50% during a one hour period is considered misuse because
the air compressor is undersized for the required air demand.
•
•
•
Repair and transportation costs of merchandise determined not to be defective.
Costs associated with assembly, required oil, adjustments or other installation and start-up costs.
Expendable parts or accessories supplied with the product which are expected to become inoperative or
unuseable after a reasonable period of use, including but not limited to sanding disks or pads, saw and shear
blades, grinding stones, springs, chisels, nozzles, o-rings, air jets, washers and similar accessories.
Merchandise sold by Porter-Cable which has been manufactured by and identified as the product of another
company, such as gasoline engines. The product manufacturer's warranty, if any, will apply.
ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT
FROM ANY DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCT IS NOT COVERED BY THIS
WARRANTY. Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
•
•
•
IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. Some states do
not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
Porter-Cable Corporation
Jackson, TN USA
1-888-559-8550
20- ENG
D27927
Download from Www.Somanuals.com. All Manuals Search And Download.
|