Porter Cable Chainsaw Sharpener 423MAG User Manual

ESPAÑOL : PÁGINA 15  
FRANÇAISE : PAGE 3131  
Instruction  
manual  
Double Insulated  
Circular Saw  
MODELS  
423MAG and 424MAG  
IMPORTANT  
Please make certain that the person who is  
to use this equipment carefully reads and  
understands these instructions before  
starting operations.  
To learn more about Porter-Cable  
visit our website at:  
The Model and Serial No. plate is located on the main  
housing of the tool. Record these numbers in the  
spaces below and retain for future reference.  
Model No. ______________________________________  
Type ___________________________________________  
Serial No._______________________________________  
Copyright © 2004 Porter-Cable Corporation  
Part No. 912490 - 05-12-04  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Do not expose power tools to rain or wet conditions. Water entering  
a power tool will increase the risk of electric shock.  
4. Do not abuse the cord. Never use the cord to carry the tools or pull  
the plug from an outlet. Keep cord away from heat, oil, sharp edges or  
moving parts. Replace damaged cords immediately. Damaged cords  
increase the risk of electric shock.  
5. When operating a power tool outside, use an outdoor extension  
cord marked “W-A” or “W”. These cords are rated for outdoor use and  
reduce the risk of electric shock.  
PERSONAL SAFETY  
1. Stay alert, watch what you are doing, and use common sense when  
operating a power tool. Do not use tool while tired or under the  
influence of drugs, alcohol, or medication. A moment of inattention while  
operating power tools may result in serious personal injury.  
2. Dress properly. Do not wear loose clothing or jewelry. Contain long  
hair. Keep your hair, clothing, and gloves away from moving parts.  
Loose clothes, jewelry, or long hair can be caught in moving parts.  
3. Avoid accidental starting. Be sure switch is OFF before plugging in.  
Carrying tools with your finger on the switch or plugging in tools that have  
the switch ON invites accidents.  
4. Remove adjusting keys or wrenches before turning the tool ON. A  
wrench or a key that is left attached to a rotating part of the tool may result  
in personal injury.  
5. Do not overreach. Keep proper footing and balance at all times.  
Proper footing and balance enables better control of the tool in unexpected  
situations.  
6. Use safety equipment. Always wear eye protection. Dust mask, non-  
skid safety shoes, hard hat, or hearing protection must be used for  
appropriate conditions.  
TOOLS USE AND CARE  
1. Use clamps or other practical way to secure and support the  
workpiece to a stable platform. Holding the work by hand or against your  
body is unstable and may lead to loss of control.  
2. Do not force tool. Use the correct tool for your application. The  
correct tool will do the job better and safer at the rate for which it is  
designed.  
3. Do not use tool if switch does not turn it ON or OFF. Any tool that  
cannot be controlled with the switch is dangerous and must be repaired.  
4. Disconnect the plug from the power source before making any  
adjustments, changing accessories, or storing the tool. Such preventive  
safety measures reduce the risk of starting the tool accidentally.  
5. Store idle tools out of reach of children and other untrained  
persons. Tools are dangerous in the hands of untrained users.  
6. Maintain tools with care. Keep cutting tools sharp and clean.  
Properly maintained tools, with sharp cutting edges are less likely to bind  
and are easier to control.  
7. Check for misalignment or binding of moving parts, breakage of  
parts, and any other condition that may affect the tool’s operation. If  
damaged, have the tool serviced before using. Many accidents are  
caused by poorly maintained tools.  
8. Use only accessories that are recommended by the manufacturer  
for your model. Accessories that may be suitable for one tool may become  
hazardous when used on another tool.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE  
1. Tool service must be performed only by qualified repair personnel.  
Service or maintenance performed by unqualified personnel could result in a  
risk of injury.  
2. When servicing a tool, use only identical replacement parts. Follow  
instructions in the Maintenance Section of this manual. Use of  
unauthorized parts or failure to follow Maintenance Instructions may create a  
risk of electric shock or injury.  
ADDITIONAL SPECIFIC SAFETY RULES  
1.  
Keep hands away from cutting area and blade. Keep  
your second hand on auxiliary handle or motor housing. If both hands are  
holding the saw, they cannot be cut by the blade.  
2. Keep your body positioned to either side of the saw blade, but not in  
line with the saw blade. KICKBACK could cause the saw to jump backwards.  
(See "Causes and Operator Prevention of KICKBACK.")  
3. Do not reach underneath the work. The guard cannot protect you from  
the blade below the work.  
4. Check lower guard for proper closing before each use. Do not operate  
saw if lower guard does not move freely and close instantly. Never clamp  
or tie the lower guard into the open position. If saw is accidentally dropped,  
lower guard may be bent. Raise the lower guard with the Retracting Handle and  
make sure it moves freely and does not touch the blade or any other part, in all  
angles and depths of cut.  
5. Check the operation and condition of the lower guard spring. If the  
guard and the spring are not operating properly, they must be serviced  
before use. Lower guard may operate sluggishly due to damaged parts, gummy  
deposits, or a buildup of debris.  
6. Lower guard should be retracted manually only for special cuts such  
as “Pocket Cuts” and “Compound Cuts.” Raise lower guard by Retracting  
Handle. As soon as blade enters the material, lower guard must be  
released. For all other sawing, the lower guard should operate automatically.  
7. Always observe that the lower guard is covering the blade before  
placing saw down on bench or floor. An unprotected, coasting blade will  
cause the saw to walk backwards, cutting whatever is in its path. Be aware of  
the time it takes for the blade to stop after switch is released.  
8. NEVER hold piece being cut in your hands or across your Ieg. It is  
important to support the work properly to minimize body exposure, blade  
binding, or loss of control.  
9. Hold tool by insulated gripping surfaces when performing an operation  
where the cutting tool may contact hidden wiring. Contact with a “live” wire  
will also make exposed metal parts of the tool “live” and shock the operator.  
10. When ripping always use a rip fence or straight edge guide. This  
improves the accuracy of cut and reduces the chance for blade binding.  
11. Always use blades with correct size and shape (diamond vs. round)  
arbor holes. Blades that do not match the mounting hardware of the saw will  
run eccentrically, causing loss of control.  
12. Never use damaged or incorrect blade washers or bolts. The blade  
washers and bolt were specially designed for your saw, for optimum  
performance and safety of operation.  
Kickback is the result of tool misuse and/or incorrect operating procedures or  
conditions and can be avoided by taking proper precautions as given below:  
13. Causes and Operator Prevention of Kickback:  
Kickback is a sudden reaction to a pinched, bound, or misaligned saw blade,  
causing an uncontrolled saw to lift up and out of the workpiece toward the  
operator.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
When the blade is pinched or bound tightly by the kerf closing down,  
the blade stalls and the motor reaction drives the unit rapidly back  
toward the operator.  
If the blade becomes twisted or misaligned in the cut, the teeth at the  
back edge of the blade can dig into the top surface of the wood causing  
the blade to climb out of the kerf and jump back toward the operator.  
Kickback is the result of tool misuse and/or incorrect operating procedures  
or conditions and can be avoided by taking proper precautions as given  
below:  
14. Maintain a firm grip on the saw and position your body and arm in a  
way that allows you to resist KICKBACK forces. KICKBACK forces can be  
controlled by the operator, if proper precautions are taken.  
15. When blade is binding, or when interrupting a cut for any reason,  
release the trigger and hold the saw motionless in the material until the  
blade comes to a complete stop. Never attempt to remove the saw from the  
work or pull the saw backward while the blade is in motion or KICKBACK  
may occur. Investigate and take corrective actions to eliminate the cause of  
blade binding.  
16. When restarting a saw in the workpiece, center the saw blade in the  
kerf and check that teeth are not engaged into the material. If saw blade is  
binding, it may walk up or KICKBACK from the workpiece as the saw is  
restarted.  
17. Support large panels to minimize the risk of blade pinching and  
KICKBACK. Large panels tend to sag under their own weight. Supports must be  
placed under the panel on both sides, near the line of cut and near the edge of  
the panel.  
18. Do not use dull or damaged blade. Unsharpened or improperly set blades  
produce narrow kerf causing excessive friction, blade binding, and KICKBACK.  
19. Blade depth and bevel adjusting locking levers must be tight and  
secure before making cut. If blade adjustment shifts while cutting, it will cause  
binding and KICKBACK.  
20. Use extra caution when making a “Pocket Cut” into existing walls or  
other blind areas. The protruding blade may cut objects that can cause  
KICKBACK.  
21. Some wood contains preservatives which can be toxic. Take extra care to  
prevent inhalation and skin contact when working with these materials. Request,  
and follow, all safety information available from your material supplier.  
Improper operation or maintenance of this product could result  
in serious injury and property damage. Read and understand all warnings and  
operating instructions before using this tool. When using power tools, basic  
safety precautions should always be followed to reduce the risk of personal  
injury. For additional information visit our website www.porter-cable.com.  
Additional Information regarding the safe and proper operation of power tools  
(i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner  
Information is also available from the National Safety Council, 1121 Spring Lake  
Drive, Itasca, IL 60143-3201, the American National Standards Institute ANSI  
01.1Safety Requirements for Woodworking Machines, and the U.S. Department  
of Labor regulations.  
There are certain applications for which this tool was  
designed. Porter-Cable strongly recommends that this tool NOT be modified  
and/or used for any application other than for which it was designed. If you have  
any questions relative to its application, DO NOT use the tool until you have  
written Porter-Cable and we have advised you.  
Technical Service Manager  
Porter-Cable Corporation  
4825 Highway 45 North  
Jackson, TN 38305  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
SYMBOL  
DEFINITION  
........................ volts  
V
A
........................ amperes  
........................ hertz  
........................ watts  
........................ kilowatts  
........................ microfarads  
........................ liters  
Hz  
W
kW  
µF  
l
kg  
........................ kilograms  
N/cm2 ........................ newtons per square centimeter  
Pa  
h
min  
s
........................ pascals  
........................ hours  
........................ minutes  
........................ seconds  
........................ alternating current  
3
........................ three-phase alternating current  
3N  
........................ three-phase alternating current with neutral  
........................ direct current  
........................ no load speed  
n0  
........................ alternating or direct current  
....................... Class II Construction  
........................ splash-proof construction  
........................ watertight construction  
…/min ........................ revolutions or reciprocation per minute  
REPLACEMENT PARTS  
When servicing use only identical replacement parts.  
MOTOR  
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60  
cycle A.C. current and voltage within plus or minus 5 percent of that shown  
on the specification plate on the tool. Several models, however, are designed  
for A.C. current only. Refer to the specification plate on your tool for proper  
voltage and current rating.  
Do not operate your tool on a current on which the voltage is  
not within correct limits. Do not operate tools rated A.C. only on D.C.  
current. To do so may seriously damage the tool.  
EXTENSION CORD SELECTION  
If an extension cord is used, make sure the conductor size is large enough to  
prevent excessive voltage drop which will cause loss of power and possible  
motor damage. A table of recommended extension cord sizes will be found  
in this section. This table is based on limiting line voltage drop to 5 volts (10  
volts for 230 volts) at 150% of rated amperes.  
If an extension cord is to be used outdoors it must be marked with the suffix  
W-A or W following the cord type designation. For example – SJTW-A to  
indicate it is acceptable for outdoor use.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS  
Length of Cord in Feet  
115V  
230V  
25 Ft.  
50 Ft.  
50 Ft.  
100 Ft. 150 Ft. 200 Ft.  
250 Ft. 300 Ft.  
500 Ft. 600 Ft.  
400 Ft. 500 Ft.  
800 Ft. 1000 Ft.  
100 Ft. 200 Ft. 300 Ft. 400 Ft.  
0-2  
2-3  
18  
18  
18  
18  
18  
18  
18  
16  
16  
16  
14  
14  
18  
18  
18  
18  
16  
16  
14  
14  
12  
12  
12  
12  
18  
16  
16  
14  
14  
12  
12  
10  
10  
10  
8
16  
14  
14  
12  
12  
10  
10  
8
16  
14  
12  
12  
10  
10  
8
14  
12  
12  
10  
10  
8
14  
12  
10  
10  
8
12  
10  
10  
8
12  
10  
8
3-4  
4-5  
8
5-6  
8
6
6-8  
6
6
6
8-10  
10-12  
12-14  
14-16  
16-18  
18-20  
8
6
6
4
8
6
6
4
4
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
FUNCTIONAL DESCRIPTION  
FOREWORD  
Your Porter-Cable circular saw is designed for use with 7-1/4" diameter  
blades that have a 5/8" diameter bore. Blades must be rated for 6000 RPM  
operation (or higher).  
A mounting flange kit for diamond-hole blades is available. This kit adapts  
the saw for use with 7-1/4" diameter blades that have a diamond-shaped  
mounting hole.  
BLADE BRAKE (Model 424MAG only)  
Model 424MAG is equipped with an electric blade brake that energizes  
automatically when the trigger switch is released.  
ASSEMBLY  
REMOVING THE BLADE  
DISCONNECT TOOL FROM POWER SOURCE.  
Avoid contact with the blade teeth to prevent personal  
injury.  
This tool is equipped with a Quick Change  
blade clamp  
and is designed to be tightened hand-tight only. The use of  
external tools may cause damage to the blade clamp.  
DO NOT USE the Quick  
blade clamp with any product  
Change  
A
other than specified Porter-Cable tools  
423MAG and 424MAG.  
1. Push in the arbor lock button (A) Fig. 1  
and rotate the blade by hand until the  
lock engages the blade arbor.  
Fig. 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
A
A
Fig. 2  
Fig. 3  
2. While pressing the arbor lock button, extend the lever on the Quick  
Change the blade clamp (A) Fig. 2 and turn it clockwise (left-hand  
thread).  
3. Remove the Quick Change blade clamp, release the arbor lock button,  
and remove the outer blade flange.  
NOTE: DO NOT use wet lubricants on the Quick Change blade clamp.  
Verify that the Quick Change blade clamp lever is tight, and  
quickly returns to its closed position before connecting the tool to the  
power source. If it doesn’t return, clear the debris from the clamp. Visually  
inspect the blade clamp lever regularly to ensure that it is not extended  
during use.  
INSTALLING THE BLADE  
DISCONNECT TOOL FROM POWER SOURCE.  
Avoid contact with the blade teeth to prevent personal  
injury.  
A
Fig. 4  
Fig. 5  
1. Remove any accumulated sawdust or other contaminants from the  
guards, from around the arbor, and from the blade clamp.  
2. Clean the inner blade flange, retract the telescoping guard, and place  
the new blade on the arbor. Verify that the teeth point up at the front of  
the saw (Fig. 4).  
3. Place the outer blade flange (A) Fig. 5 on the arbor with the smooth side  
against the blade. Mate the flats with those on the arbor.  
4. Replace the Quick Change blade clamp (A) Fig. 2 finger tight by turning  
it counter-clockwise. Push in the arbor lock button (A) Fig.1, extend the  
lever on the Quick Change blade clamp (A) Fig. 2, and hand-tighten the  
assembly securely. Release the arbor lock.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
TELESCOPING GUARD  
The telescoping guard (A) Fig. 3 is a safety device important to your  
protection. Every time you use the saw, verify that the telescoping guard  
rotates freely and returns quickly and completely to its closed position. At  
least once a month, remove any accumulated debris (sawdust, pitch, etc.)  
from the area around the hub (B) of the telescoping guard. DO NOT  
LUBRICATE THIS AREA. The hub has a dry film lubricated surface that  
does not need oiling. DO NOT block or wedge the telescoping guard in the  
open position.  
DO NOT use your saw if the telescoping guard is not in  
working order. If telescoping guard movement is sluggish or  
binding exists, return the saw to your nearest AUTHORIZED  
PORTER-CABLE SERVICE STATION or PORTER-CABLE  
SERVICE CENTER for repair.  
TO ADJUST DEPTH OF CUT FOR NORMAL CUTTING  
Adjust the depth of cut so that the saw blade barely protrudes through the  
thickness of the workpiece. To adjust:  
DISCONNECT TOOL FROM POWER SOURCE.  
1. Lift the depth adjustment locking lever (A) Fig. 6, located at the rear of  
the saw.  
2. Raise or lower the saw housing to the correct level.  
NOTE: The upper guard (B) Fig. 6 is marked in 1/4" increments for  
convenience in setting the depth of cut. Align the depth segment mark  
(C) Fig. 6 with the desired depth marking on the guard.  
3. Press the depth-adjusting locking lever down firmly to lock the saw in  
the selected position.  
A
C
B
A
B
C
D
Fig. 6  
Fig.7  
TO ADJUST FOR BEVEL CUTS  
DISCONNECT TOOL FROM POWER SOURCE.  
1. Loosen the bevel adjusting lever (A) Fig. 7.  
2. Tilt the saw base until the desired graduation line on the bevel segment  
(B) Fig. 7 aligns with the indicator (C) Fig. 7 on the bracket.  
3. Tighten the bevel adjusting lever firmly.  
4. For bevel cuts greater than 45°, set the guide on the 45° mark. Lift the  
bevel adjusting lever into the slot (D) Fig. 7 and move the saw base to  
the greater angle. Tighten the bevel adjusting lever firmly.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
0° POSITIVE STOP  
The saw is equipped with an adjustable positive stop at 0°. Check the  
accuracy of this stop periodically. To adjust:  
DISCONNECT TOOL FROM POWER SOURCE.  
1. Loosen the bevel adjustment lever (A) Fig. 8, and position the base for a  
0° cut. Confirm that the bevel-stop sleeve (B) Fig. 8 is against the 0°  
stop screw (C).  
2. Turn the saw upside down, retract the telescoping guard, and check to  
see that the blade is square (Fig. 9).  
3. To adjust, loosen the bevel adjustment knob (A) Fig. 8. While keeping  
the bevel stop sleeve (B) Fig. 8 in contact with the stop screw (C) Fig. 8,  
use a screwdriver to turn the adjusting screw (A) Fig. 10 until the blade  
is square.  
A
A
B
C
Fig. 8  
Fig.9  
Fig. 10  
LINE-OF-CUT INDICATOR  
Line-of-cut indicator slots (A) Fig. 11 are provided  
at the front of the saw base. The right slot is used  
to follow a line when making a 0° cut. The left slot  
is used to follow a line when making a 45° cut.  
The straight side of the notch indicates the cut  
line.  
USING SAWDUST EXHAUST NOZZLE  
A
The sawdust exhaust nozzle in the closed position  
(Fig. 12) directs the sawdust to the rear of the saw.  
Fig. 11  
The sawdust exhaust nozzle pointing forward (Fig. 13) directs the sawdust  
to the front. To change the position of the nozzle, push down on the top of  
the nozzle and turn the nozzle to the new position. An accessory vacuum  
hose assembly is available for connecting the sawdust exhaust nozzle in the  
forward position directly to a shop type vacuum cleaner.  
DO NOT direct sawdust toward yourself or others. To  
avoid injury from flying sawdust, keep the exhaust nozzle either in the  
forward position or in the closed position. DO NOT insert foreign objects  
into the exhaust opening.  
Fig. 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fig.13  
10  
INSTALLING THE OPTIONAL RIP GUIDE  
1. Insert the rip guide (A) Fig. 14 through the slots (B). Slide the guide in  
until it extends through the both slots in the sawbase.  
2. Place the compression spring on the thumb screw (C) Fig. 14 (supplied  
with the rip guide), and thread into the hole in the saw base. DO NOT  
TIGHTEN.  
3. Adjust the rip guide for the desired width of cut and tighten the thumb  
screw.  
To avoid personal injury and damage to workpiece, extend  
the rip guide through both slots in the base.  
B C  
A
Fig.14  
Fig.15  
Fig. 16  
HOW TO USE THE SAW  
DO NOT use your saw if the telescoping guard is not  
working. If the telescoping guard binds or is sluggish, return  
the saw to your nearest AUTHORIZED PORTER-CABLE  
SERVICE STATION or PORTER-CABLE SERVICE  
CENTER for repair.  
For your maximum protection, effective control of this  
powerful saw requires two-handed operation. Support the  
work properly and hold the saw firmly to prevent loss of  
control which could cause injury. See Fig. 15 for the proper  
way to hold the tool.  
Keep the cord away from cutting area to prevent electric  
shock.  
GUARD AGAINST KICKBACK.  
Kickback is a sudden reaction to a pinched, bound, or  
misaligned saw blade, causing an uncontrolled saw to lift up  
and out of the workpiece toward the operator. Keep your  
body to the side of the saw.  
Stay alert and maintain a firm grip on the saw. Release the  
switch immediately if the blade binds or the saw stalls. Keep  
your blade sharp. Support the panels (Fig. 16). Use a fence  
or a straight edge guide when ripping. DO NOT force the  
tool. DO NOT remove the saw from the workpiece while the  
blade is moving.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fig. 18  
Fig.17  
CROSS-CUTTING  
Cutting directly across the grain of a piece of lumber is called crosscutting.  
Position the work so that the cut will be on the left.  
RIPPING  
Cutting wood lengthwise is referred to as ripping. This operation is  
performed in the same manner as crosscutting with the exception of  
supporting the workpiece. If the workpiece is supported on a large table,  
bench, or floor, place several pieces of scrap stock approximately one inch  
thick beneath the workpiece to allow clearance for the portion of the saw  
blade that extends through the material (Fig. 17). When using saw horses,  
place 2 x 4’s lengthwise between the horses and the large sheets of  
paneling or thin plywood to prevent the workpiece from sagging in the  
center.  
For narrow rip cuts, use the rip guide (available as an accessory). Guide the  
saw by keeping the inner face of the rip guide (Fig. 18) tight against the edge  
of the board.  
For making wider cuts (plywood and wide sheets), tack or clamp a wooden  
guide strip to guide the left edge of the saw base (Fig. 17).  
NOTE: Adjust the depth of cut to allow for the thickness of the wooden  
guide strip.  
A
Fig. 19  
Fig. 20  
BEVEL CUTTING  
Bevel cuts are made in the same manner as crosscuts and rip cuts. The  
difference is that the blade is set at an angle between 0° and 45°(Fig. 19).  
The bevel cut made at an angle to the edge of a board is called a compound  
cut. Certain compound cuts may require you to manually retract the  
telescoping guard to allow the blade to enter into and/or through the cut.  
Use the lever (A) Fig. 20 provided on the telescoping guard  
when you have to retract the telescoping guard manually.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
POCKET CUTS (PLUNGE CUTTING)  
A pocket cut is one which must be made inside  
the area of the workpiece and not starting from  
the edge. Mark the area clearly with lines on all  
sides. Start near the corner of one side and  
place the front edge of the saw base firmly on  
the workpiece. Hold the saw up so that the  
blade clears the material. Confirm that you have  
adjusted the blade properly for the depth of cut.  
Push the telescoping guard lever all the way  
back so the blade is exposed (Fig. 21).  
Fig. 21  
Keep your hands and fingers away from the blade.  
Start the motor and lower the blade into the work. After the blade has cut  
through, and the base rests flat on the work, follow the line to the corner.  
Let the saw come to a complete stop before removing it  
from the workpiece.  
Use a keyhole or bayonet saw to cut clean corners.  
MAINTENANCE  
KEEP TOOL CLEAN  
Periodically blow out all air passages with dry compressed air. All plastic  
parts should be cleaned with a soft damp cloth. NEVER use solvents to  
clean plastic parts. They could possibly dissolve or otherwise damage the  
material.  
Wear ANSI Z87.1 safety glasses while using compressed air.  
FAILURE TO START  
Should your tool fail to start, check to make sure the prongs on the cord  
plug are making good contact in the outlet. Also, check for blown fuses or  
open circuit breakers in the line.  
LUBRICATION  
This tool has been lubricated with a sufficient amount of high grade lubricant  
for the life of the unit under normal operating conditions. No further  
lubrication is necessary.  
BRUSH INSPECTION AND LUBRICATION  
For your continued safety and electrical protection, brush inspection and  
replacement on this tool should ONLY be performed by an AUTHORIZED  
PORTER-CABLE SERVICE STATION or a PORTER-CABLE·DELTA  
FACTORY SERVICE CENTER.  
At approximately 100 hours of use, take or send your tool to your nearest  
authorized Porter-Cable Service Station to be thoroughly cleaned and  
inspected. Have worn parts replaced and lubricate with fresh lubricant. Have  
new brushes installed, and test the tool for performance.  
Any loss of power before the above maintenance check may indicate the  
need for immediate servicing of your tool. DO NOT CONTINUE TO  
OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is  
present, return your tool to the service station for immediate service.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND REPAIRS  
All quality tools will eventually require servicing or replacement of parts due  
to wear from normal use. These operations, including brush inspection and  
replacement, should ONLY be performed by either an AUTHORIZED  
PORTER-CABLE SERVICE STATION or a PORTER-CABLEDELTA  
FACTORY SERVICE CENTER. All repairs made by these agencies are fully  
guaranteed against defective material and workmanship. We cannot  
guarantee repairs made or attempted by anyone other than these agencies.  
Should you have any questions about your tool, feel free to write us at any  
time. In any communications, please give all information shown on the  
nameplate of your tool (model number, type, serial number, etc.).  
ACCESSORIES  
A complete line of accessories is available from your Porter-Cable•  
Delta Supplier, Porter-CableDelta Factory Service Centers, and Porter-  
Cable Authorized Service Stations. Please visit our Web Site  
www.porter-cable.com for a catalog or for the name of your nearest  
supplier.  
Since accessories other than those offered by Porter-  
Cable ·Delta have not been tested with this product, use  
of such accessories could be hazardous. For safest  
operation, only Porter-Cable·Delta recommended  
accessories should be used with this product.  
PORTER-CABLE LIMITED  
ONE YEAR WARRANTY  
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original  
purchase. We will repair or replace at our option, any part or parts of the product and accessories  
covered under this warranty which, after examination, proves to be defective in workmanship or  
material during the warranty period. For repair or replacement return the complete tool or accessory,  
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.  
Proof of purchase may be required. This warranty does not apply to repair or replacement required  
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service  
Centers or Authorized Service Stations.  
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE  
OF PURCHASE.  
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,  
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING  
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY  
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL  
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied  
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you.  
This warranty gives you specific legal rights and you may also have other legal rights which vary  
from state to state.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PORTER-CABLE • DELTA SERVICE CENTERS  
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)  
(CENTRE DE SERVICE PORTER-CABLE • DELTA)  
Parts and Repair Service for Porter-Cable  
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable  
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)  
Delta Power Tools are Available at These Locations  
Delta)  
Cleveland 44125  
8001 Sweet Valley Drive  
Unit #19  
Phone: (216) 447-9030  
Fax: (216) 447-3097  
ARIZONA  
MINNESOTA  
Minneapolis 55429  
5522 Lakeland Avenue North  
Phone: (763) 561-9080  
Fax: (763) 561-0653  
GEORGIA  
Tempe 85282 (Phoenix)  
2400 West Southern Avenue  
Suite 105  
Phone: (602) 437-1200  
Fax: (602) 437-2200  
Forest Park 30297 (Atlanta)  
5442 Frontage Road,  
Suite 112  
Phone: (404) 608-0006  
Fax: (404) 608-1123  
OREGON  
MISSOURI  
Portland 97230  
CALIFORNIA  
North Kansas City 64116  
1141 Swift Avenue  
Phone: (816) 221-2070  
Fax: (816) 221-2897  
ILLINOIS  
4916 NE 122 nd Ave.  
Phone: (503) 252-0107  
Fax: (503) 252-2123  
Ontario 91761 (Los Angeles)  
3949A East Guasti Road  
Phone: (909) 390-5555  
Fax: (909) 390-5554  
Addison 60101 (Chicago)  
400 South Rohlwing Rd.  
Phone: (630) 424-8805  
Fax: (630) 424-8895  
PENNSYLVANIA  
St. Louis 63119  
Willow Grove 19090 (Philadelphia)  
520 North York Road  
Phone: (215) 658-1430  
Fax: (215) 658-1433  
7574 Watson Road  
Phone: (314) 968-8950  
Fax: (314) 968-2790  
Woodridge 60517 (Chicago)  
2033 West 75th Street  
Phone: (630) 910-9200  
Fax: (630) 910-0360  
San Diego 92111  
7638 Clairemnot Blvd.  
Phone: (858) 277-9595  
Fax: (858) 277-9696  
NEW YORK  
TEXAS  
Flushing 11365-1595 (N.Y.C.)  
175-25 Horace Harding Expwy.  
Phone: (718) 225-2040  
Fax: (718) 423-9619  
MARYLAND  
San Leandro 94577 (Oakland)  
3039 Teagarden Street  
Phone: (510) 357-9762  
Fax: (510) 357-7939  
Carrollton 75006 (Dallas)  
1300 Interstate 35 N, Suite 112  
Phone: (972) 446-2996  
Fax: (972) 446-8157  
Elkridge 21075 (Baltimore)  
7397-102 Washington Blvd.  
Phone: (410) 799-9394  
Fax: (410) 799-9398  
NORTH CAROLINA  
Charlotte 28270  
9129 Monroe Road, Suite 115  
Phone: (704) 841-1176  
Fax: (704) 708-4625  
COLORADO  
Houston 77043  
4321 Sam Houston Parkway, West  
Suite 180  
Phone: (713) 983-9910  
Fax: (713) 983-6645  
MASSACHUSETTS  
Arvada 80003 (Denver)  
8175 Sheridan Blvd., Unit S  
Phone: (303) 487-1809  
Fax: (303) 487-1868  
Franklin 02038 (Boston)  
Franklin Industrial Park  
101E Constitution Blvd.  
Phone: (508) 520-8802  
Fax: (508) 528-8089  
OHIO  
FLORIDA  
WASHINGTON  
Columbus 43214  
4560 Indianola Avenue  
Phone: (614) 263-0929  
Fax: (614) 263-1238  
Davie 33314 (Miami)  
4343 South State Rd. 7 (441)  
Unit #107  
Phone: (954) 321-6635  
Fax: (954) 321-6638  
Auburn 98001(Seattle)  
3320 West Valley HWY, North  
Building D, Suite 111  
Phone: (253) 333-8353  
Fax: (253) 333-9613  
MICHIGAN  
Madison Heights 48071 (Detroit)  
30475 Stephenson Highway  
Phone: (248) 597-5000  
Fax: (248) 597-5004  
Tampa 33609  
4538 W. Kennedy Boulevard  
Phone: (813) 877-9585  
Fax: (813) 289-7948  
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and  
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service  
Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to  
the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.  
Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-  
Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable Delta, Centro de Servicio Autorizado o Centro  
de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de  
Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au  
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-  
Cable  
Delta, s’adresser à tout distributeur Porter-Cable  
Delta, centre de service agréé ou centre de service d’usine Porter-Cable  
Delta. Si  
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable  
Delta le  
plus proche.  
CANADIAN PORTER-CABLE DELTA SERVICE CENTERS  
QUÉBEC  
ALBERTA  
MANITOBA  
1515 Ave.  
Bay 6, 2520-23rd St. N.E.  
Calgary, Alberta  
T2E 8L2  
1699 Dublin Avenue  
Winnipeg, Manitoba  
R3H 0H2  
St-Jean Baptiste, Suite 160  
Québec, P.Q.  
G2E 5E2  
Phone: (418) 877-7112  
Fax: (418) 877-7123  
Phone: (403) 735-6166  
Fax: (403) 735-6144  
Phone: (204) 633-9259  
Fax: (204) 632-1976  
BRITISH COLUMBIA  
8520 Baxter Place  
Burnaby, B.C.  
V5A 4T8  
Phone: (604) 420-0102  
Fax: (604) 420-3522  
ONTARIO  
1447, Begin  
St-Laurent, (Mtl), P.Q.  
H4R 1V8  
Phone: (514) 336-8772  
Fax: (514) 336-3505  
505 Southgate Drive  
Guelph, Ontario  
N1H 6M7  
Phone: (519) 767-4132  
Fax: (519) 767-4131  
The following are trademarks of PORTER-CABLE  
DELTA (Las siguientes son marcas registradas de PORTER-CABLE  
DELTA S.A.) (Les  
marques suivantes sont des marques de fabriquant de la PORTER-CABLE  
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,  
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying  
Chips™, FRAME SAW®, Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-  
SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-  
CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-  
3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®,  
Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®,  
The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-  
LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®,  
UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®,  
WOODWORKER’S CHOICE™.  
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.  
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden  
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et  
Printed in U.S.A. PC-0104-150  
Download from Www.Somanuals.com. All Manuals Search And Download.  
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.  

Philips Clock Radio J3540 User Manual
Philips CRT Television 14PT1686 User Manual
Philips Home Theater System CSS2123 F7 User Manual
Philips Surge Protector SPP7344WA User Manual
Pioneer Car Stereo System CDX FM673 User Manual
Pioneer Plumbing Product VSW 1 2 User Manual
Polaris Offroad Vehicle 600 IQ Widetrak User Manual
Polk Audio Speaker CSR User Manual
Printronix Printer T4204 User Manual
PYLE Audio Computer Monitor PLVW20T User Manual