Administrator’s Guide
for the V500 System
July 2004 Edition
3725-21743-003/A
V500 Version 7.0
Connect. Any Way You Want.
Download from Www.Somanuals.com. All Manuals Search And Download.
About this Guide
The Administrator’s Guide for the V500 System is for administrators of the
V500 system who need to:
❑ Learn about and set up the system hardware
❑ Configure the system
❑ Customize the behavior and appearance of the system for easy and efficient
use
❑ Obtain information about calls made by the system, and gather usage and
performance data
❑ Troubleshoot any issues that occur with the system
Other documents available for the V500 system include:
❑ Setting Up the System, which describes how to install the hardware
❑ The Getting Started Guide, which describes how to place calls and perform other
video calling tasks
❑ Setup Sheets, which describe how to install optional hardware
❑ Release Notes
For support or service, please contact your Polycom distributor or go to Polycom
Polycom recommends that you record the serial number of your V500 system here
for future reference. The serial number for the system is printed on the unit.
System Serial Number: ____________________________________________
© Polycom, Inc.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
iv
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Key Features ..........................................................................................................................................1 - 2
Rich Conference Experience .........................................................................................................1 - 2
Enhanced User Experience ...........................................................................................................1 - 2
Easy Installation .............................................................................................................................1 - 3
Security and Network Management ...........................................................................................1 - 3
Standard System Components ............................................................................................................1 - 5
Optional System Components ............................................................................................................1 - 6
Standard System Set-up .......................................................................................................................2 - 2
Positioning the System ..................................................................................................................2 - 2
Connecting the Monitor ................................................................................................................2 - 3
Connecting the System to the LAN ............................................................................................2 - 3
Connecting Power .........................................................................................................................2 - 4
Installing Batteries in the Remote Control .................................................................................2 - 5
Powering on the System ...............................................................................................................2 - 5
Optional Equipment Set-up ................................................................................................................2 - 6
Connecting to a BRI Network Interface .....................................................................................2 - 6
Connecting Headphones ..............................................................................................................2 - 6
Getting the Network Ready ................................................................................................................3 - 2
Network Connectivity Checklist ........................................................................................................3 - 2
Configuring with the Setup Wizard ..................................................................................................3 - 3
Configuring LAN Properties ..............................................................................................................3 - 4
Configuring IP Network Support ......................................................................................................3 - 6
Specifying H.323 Settings .............................................................................................................3 - 6
Configuring the System to Use a Gatekeeper ....................................................................3 - 7
Configuring the System to Use a Gateway .........................................................................3 - 8
Specifying SIP Settings ..................................................................................................................3 - 9
Specifying Quality of Service .....................................................................................................3 - 10
Configuring the System for Use with a Firewall or NAT ......................................................3 - 11
Configuring ISDN Support ...............................................................................................................3 - 13
Configuring the BRI Network Interface ...................................................................................3 - 13
Configuring Call Preferences ............................................................................................................3 - 14
Configuring the Global Directory ....................................................................................................3 - 16
Configuring the Directory Server Settings ...............................................................................3 - 16
Setting the Dialing Rules ............................................................................................................3 - 17
Placing a Test Call ...............................................................................................................................3 - 17
Checking System Status .....................................................................................................................3 - 18
Keeping your Software Current .......................................................................................................3 - 19
© Polycom, Inc.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Managing User Access to Settings and Features ............................................................................. 4 - 2
Limiting What Users Can Do With the System ........................................................................ 4 - 5
Configuring Directory Settings ................................................................................................. 4 - 12
Customizing the Workspace Appearance ...................................................................................... 4 - 16
Adding Sites to the Home Screen ............................................................................................. 4 - 19
Adding On-screen Instructions ................................................................................................. 4 - 20
Using Marquee Text ............................................................................................................ 4 - 20
Changing System Appearance .................................................................................................. 4 - 21
Audio Options for Closed Captioners ..................................................................................... 4 - 22
Using the V500 Web Interface ............................................................................................................ 5 - 2
Managing System Profiles with the V500 Web Interface ........................................................ 5 - 3
Managing Directories with the V500 Web Interface ................................................................ 5 - 4
Viewing the Management Servers List ...................................................................................... 5 - 5
vi
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up SNMP ..................................................................................................................................5 - 8
Downloading MIBs .......................................................................................................................5 - 8
Configuring for SNMP Management .........................................................................................5 - 9
Call Summary ........................................................................................................................................6 - 2
Call Statistics ..........................................................................................................................................6 - 3
Call Status ..............................................................................................................................................6 - 4
Recent Calls ............................................................................................................................................6 - 5
Call Detail Report .................................................................................................................................6 - 6
Call Detail Report Archives .........................................................................................................6 - 9
Sending a Message ................................................................................................................................7 - 2
System Screens Quick Reference ........................................................................................................7 - 2
Diagnostic Screens ................................................................................................................................7 - 3
Indicators ...............................................................................................................................................7 - 7
System Lights .................................................................................................................................7 - 7
Network Interface Lights ..............................................................................................................7 - 7
General Troubleshooting .....................................................................................................................7 - 8
Critical Problems ...........................................................................................................................7 - 8
Severe Problems .............................................................................................................................7 - 9
Moderate Issues ...........................................................................................................................7 - 11
Minor Issues .................................................................................................................................7 - 13
Normal System Behaviors ..........................................................................................................7 - 16
How to Contact Technical Support ..................................................................................................7 - 17
By Telephone ................................................................................................................................7 - 17
By Internet ....................................................................................................................................7 - 17
LAN Cable ...................................................................................................................... Appendix - 2
Composite Video Cable ................................................................................................ Appendix - 3
Q.850 Cause Codes ............................................................................................................... Appendix - 4
© Polycom, Inc.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
viii
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Introducing the V500 System
Your V500 video conferencing system is a state-of-the-art visual collaboration tool.
With crisp, clean video and crystal-clear sound, your V500 system provides the
essential tools your home or small business needs for video conferencing over
broadband networks.
What’s in this Chapter?
Page
© Polycom, Inc.
1 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Key Features
Rich Conference Experience
❑ Best-in-class video algorithms — The H.264 video algorithm provides
smooth, natural TV-like video.
❑ State-of-the-art audio quality — The V500 system offers Polycom Siren™ 14,
a 14 kHz frequency response that delivers CD-quality sound.
❑ See more with single-monitor systems — Use Dual Monitor Emulation
(split-screen viewing) to see more even when you only have room for one
monitor.
❑ Language support — Use the V500 system user interface, remote control, and
web interface in any of twelve languages.
Enhanced User Experience
❑ Customizable home screen — Customize the home screen to support
different types of users:
•
•
Novice users — Offer just a few options, so users need little or no training.
Advanced users — Provide a wide range of video conferencing features.
❑ Customizable look and feel — Set up the workspace to suit your
environment.
❑ Easy-to-use remote control — Navigate through the configuration screens and
place calls easily using the remote control.
•
•
•
Enter text — Press the number buttons to enter text using the method
commonly used with cell phones.
Color-coded buttons — Find buttons for related features quickly since
they are color coded.
Separate buttons for calling and hanging up — Call and hang up without
confusion even if you have never made a video call before.
1 - 2
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 - Introducing the V500 System
❑ Many ways to use the directory — Find information in the directory using the
method you find most convenient.
•
•
•
Assign entries to categories — Sort your directory by department or
category.
Search by name — Quickly find people by entering the first, middle, or
last name.
Find others and let them find you — Register with the Global Directory
Server and make it easy to call other registered systems and just as easy for
the other registered systems to call you. The system automatically copies
the global directory to your system periodically, so entries are always
available.
Easy Installation
❑ Firewall (UPnP™) support — The V500 system offers support for routers that
support UPnP (Universal Plug and Play) NAT traversal, making video
conferencing setup easier for users in homes and small offices.
❑ IP or ISDN calling — The V500 system has a built-in 10/100 Mb Ethernet port
for IP calls. Add the optional single BRI network interface to make calls over
your ISDN telephone lines.
❑ Easy configuration wizard — The system setup wizard detects your network
connections and guides you through configuring the system to work on an IP
network or ISDN.
❑ Fully broadband capable — The standards-compliant V500 system works
with any other H.323 system.
❑ Auto-sensing power supply — The system automatically adjusts for line
voltages from 90 to 260 V and line frequencies from 47 to 63 Hz.
Security and Network Management
❑ Use AES encryption — Enable the integrated AES encryption to automatically
encrypt calls to other AES-capable systems, without external encryption
equipment.
❑ Remote access — Configure, manage, and monitor the system from a remote
computer using the V500 web interface (the system’s web interface), the
Polycom Global Management™ System, or SNMP. Alternatively, you can
choose not to allow remote management.
❑ Secure system management — The local administrator’s password on the
system prevents others from changing system configuration while allowing
you to manage the system.
© Polycom, Inc.
1 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
❑ Call Detail Reports — Access the system’s call history from the V500 web
interface. You can download the data to a spreadsheet application for sorting
and formatting.
❑ Remote diagnostics — Tools in the V500 web interface allow you to identify
and correct issues that affect the video conferencing experience.
❑ SNMP reporting — The V500 system sends SNMP reports to indicate a total
of 31 conditions.
1 - 4
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 - Introducing the V500 System
Standard System Components
This section describes the standard components that come with the V500 system.
Two models of the V500 system are available — IP only, and IP with ISDN.
Name
Component
Description
V500 System
The V500 system delivers high-quality,
face-to-face video communication in a
sleek package that includes the camera
and microphone.
Remote Control
The remote control is designed to make
it easy to set up and operate the system
— color-coded buttons correspond to
system features.
Composite video
cable
The composite video cable is a triple
RCA cable with S-video that connects
the V500 system to a monitor.
LAN cable
BRI cable
The LAN cable connects the system to
the IP network.
The BRI cable connects the system to
the ISDN.
(IP with ISDN
model only)
Power supply
The power supply connects power to
the system.
Documentation
Read Me First
Setting Up the V500 System
V500 system documentation CD
© Polycom, Inc.
1 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Optional System Components
To extend what you do with your V500 system, the following additional options
are available. For information about ordering these options, please see your
Polycom distributor.
❑ Single BRI network interface — Connect the system to use ISDN.
❑ Headphone — Listen privately by adding your own headphone using the
3.5 mm stereo mini jack.
1 - 6
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Setting Up Your System Hardware
This chapter describes how to set up your system with the required components
and optional equipment. If you need additional installation information, refer to
the system setup document that was provided with your system.
For optional components, you can also refer to the setup sheet that was shipped
with the component.
www.polycom.com/videodocumentation.
What’s in this Chapter?
Page
© Polycom, Inc.
2 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Standard System Set-up
This section describes how to connect the components that are required for the
basic system set-up. Procedures for connecting additional equipment are in the
Positioning the System
The V500 system is designed for homes, home offices, or small offices.
To position the system:
>> Place the system on top of your monitor. For optimal audio and video
performance, locate the monitor within 5 to 10 feet (1.52 to 3.05 meters) away
from the people in the call.
5'-10'
1.
2 - 2
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 - Setting Up Your System Hardware
Connecting the Monitor
You must connect a television monitor to the V500 system. This may be an NTSC
or PAL monitor, depending on your system.
To connect a monitor to the system:
1. Connect the monitor to the S-video or composite video outputs on the back of
the V500 system.
You must use the same type of connector on the monitor as on the system. For
example, if you use the S-video connector on the monitor, use the S-video
connector on the system.
DC IN 12V
BRI
LAN
Composite video output
S-video output
(preferred)
S-video provides superior video quality, and is recommended.
2. Connect the system’s audio outputs to the monitor’s audio inputs using the
red and white connectors on the monitor cable.
After you have finished setting up the system, you will need to configure the monitor’s
Connecting the System to the LAN
The steps you need to take to connect to the LAN depend on your network
environment. For example, you may have a small office with multiple PCs, a
broadband modem, and a router; you may have a broadband modem and one PC
in your home; or, you may have another type of network environment altogether.
In all cases, you must first connect the LAN to the system with the LAN cable. If
you have a router, gateway, or broadband modem, you must also open the ports
used by the V500 system to access the Internet. Once you have done these, refer to
the section that pertains to your environment.
© Polycom, Inc.
2 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
To connect the system to the LAN:
1. Connect the LAN cable to the LAN connector on the back of the system.
DC IN 12V
BRI
LAN
LAN connector
2. Connect the other end of the LAN cable to the LAN.
After you have finished setting up the system, you will need to configure it to work properly
Connecting Power
The V500 system has an external power supply.
Do not use a power supply other than the one supplied with your V500 system. Using the
wrong power supply will void the warranty and may damage your system.
To connect power to the system:
1. Connect the power supply to the power connector on the back of the system.
DC IN 12V
BRI
LAN
Power connector
2. Connect the power cord to the power supply.
Do not connect the V500 system power cord to a wall outlet until you have connected all
equipment to the system.
2 - 4
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 - Setting Up Your System Hardware
Installing Batteries in the Remote Control
The remote control uses three AAA batteries, which are included with the system.
To install batteries in the remote control:
1. Remove the battery cover from the back of the remote control.
2. Refer to the diagram inside the remote control, and install the batteries in the
orientation shown.
3. Reinstall the battery cover on the remote control.
Powering on the System
After you have connected all your standard and optional equipment, plug the
power cord into a wall outlet.
To power on the system:
>> Press the power switch located at the back of the system.
DC IN 12V
BRI
LAN
Power switch
© Polycom, Inc.
2 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Optional Equipment Set-up
This section describes how to connect optional components to the V500 system.
Connecting to a BRI Network Interface
The V500 system is available with the optional BRI network interface, which
allows you to make ISDN calls.
You may need an NT-1 device if your site does not use an internal telephone
system (PBX). A PBX or an NT-1 device provides the S/T interface that the
system’s BRI network interface requires.
To install the BRI network interface:
1. Make sure the system is powered off.
2. Connect the BRI cable from the BRI connector on the back of the system to
ISDN or to your NT-1 device, as appropriate.
DC IN 12V
BRI
LAN
BRI connector
3. If you are using an NT-1 device, connect it to the ISDN.
Connecting Headphones
You can connect headphones to the V500 system to listen to your calls privately.
To connect headphones to the system:
>> Connect the headphone cable to the headphone jack on the back of the system.
DC IN 12V
BRI
LAN
Headphone jack
2 - 6
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Configuring Network Use
This chapter lists the information you need to get your network ready for video
conferencing. Once you’ve gathered that information, you can begin configuring
the system’s network options. Details on how to perform this configuration are
also included in this chapter.
When you power on your system for the first time, the setup wizard detects the
system’s IP and ISDN connections and leads you through the minimum
configuration steps required to place a call.
If you need to change any of the initial settings to accommodate your environment,
you can manually adjust them using the screens described in this chapter.
Note that if you establish an administrator’s password during the setup wizard,
you will need to enter it each time you wish to change advanced settings.
What’s in this Chapter?
Page
© Polycom, Inc.
3 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Getting the Network Ready
Before you begin configuring the network options, you must make sure your
network is ready for video conferencing.
To begin, refer to the Preparing Your Network for Collaboration document, available
you need to prepare your network, such as worksheets that will help you order
ISDN.
Network Connectivity Checklist
You may need this information to make and receive video calls at your site:
If:
This information:
Should be provided by your:
Your system is using a
static IP address
IP address
IP Network Service Provider
Your network uses a
gatekeeper
Gatekeeper address
Firewall information
IP Network Service Provider
IP Network Service Provider
Your system is behind a
firewall
You are using BRI
ISDN address
SPIDs
ISDN Service Provider
ISDN Service Provider
You are using ISDN and
are in North America
You are using ISDN
ISDN switch protocols
ISDN Service Provider
3 - 2
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Configuring Network Use
Configuring with the Setup Wizard
When you power on your system for the first time, the setup wizard detects the
system’s IP and ISDN connections and leads you through the minimum
configuration steps required to place a call. If you need more information about
these steps, refer to the corresponding sections in this chapter.
The setup wizard enables you to set an administrator password, which allows you
to limit access to the Admin Settings. The administrator password may contain
letters and numbers, but no other characters.
The default administrator password is the system’s serial number. If you change the
password, make sure you remember it. If you forget the password, you will have to reset the
system, delete the system files, and run the setup wizard again in order to access the Admin
Settings and reset the password. You cannot set the administrator password from a remote
location.
You can run the setup wizard or view the configuration screens in either of these
two ways.
❑ In the room with the system — Use the remote control to navigate the screens
and enter information. You can use the number pad on the remote control to
enter text just like you can with a cell phone.
❑ From a remote location — Use a web browser to access the V500 web interface.
To do this, you need to know the IP address of the system. Polycom
recommends using Microsoft® Internet Explorer 6.0 or later.
You can use the web interface to configure all of the system settings except the remote
management settings, which must be configured on the local system.
To access the system via the V500 web interface:
1. On a PC, open a web browser.
2. In the browser address line, enter the IP address of the system (for example,
http://255.255.255.255) to go to the V500 web interface.
3. Enter your user name and the password, if a password has been established.
© Polycom, Inc.
3 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Configuring LAN Properties
If your system is part of a LAN, use this section to configure the system to work
with the LAN.
Before you Begin
If you are connecting the system via a modem, you need to request an additional
public IP address from your Internet service provider.
Your service provider will provide you with one of these IP addresses:
❑ Static IP address – The address is reserved for your system and will not
change. When you configure the LAN properties of the system, choose the
Enter IP Address Manually option.
Your service provider should also provide you with the DNS server address,
default gateway address, subnet mask, and WINS server IP address.
❑ Dynamic IP address – The address is obtained from your service provider’s
DHCP server, and therefore may change. When you configure the LAN
properties of the system, choose the Obtain IP Address Automatically option.
To configure LAN properties:
1. Go to System > Admin Settings > LAN Properties.
2. Configure these settings:
Setting
Description
Connect to my LAN Specifies whether the system is part of the LAN.
Allow IP Calls
Host Name
Enables the system to make and receive IP calls.
Indicates the system’s DNS name.
If you change the Host Name, the system restarts.
IP Address
Specifies how the system obtains an IP address.
•
Obtain IP Address Automatically — Select if the system gets
an IP address from the DHCP server on the LAN.
•
Enter IP Address Manually — Select if the IP address will not
be assigned automatically.
Your IP Address is
or
If the system obtains its IP address automatically, this area
displays the IP address currently assigned to the system.
If you selected Enter IP Address Manually, enter the IP address
here.
Use the Following
IP Address
3 - 4
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Configuring Network Use
Setting
Description
Domain Name
Displays the domain name currently assigned to the system.
If the system does not automatically obtain a domain name, enter
one here.
DNS Servers
Default Gateway
Subnet Mask
WINS Server
Displays the DNS servers currently assigned to the system.
If the system does not automatically obtain a DNS server address,
enter up to four DNS servers here.
Displays the gateway currently assigned to the system.
If the system does not automatically obtain a gateway IP address,
enter one here.
Displays the subnet mask currently assigned to the system.
If the system does not automatically obtain a subnet mask, enter
one here.
Displays the WINS server currently assigned to the system.
If the system does not automatically obtain a WINS server IP
address, enter one here.
WINS Resolution
LAN Speed
Sends a request to the WINS server for WINS name resolution.
Specify the LAN speed to use. Note that the speed you choose
must be supported by the switch.
Choose Auto to have the network switch negotiate the speed
automatically. If you choose 10 Mbps or 100 Mbps, you must also
select a duplex mode.
Duplex Mode
Specify the Duplex mode to use. Note that the Duplex mode you
choose must be supported by the switch.
Choose Auto to have the network switch negotiate the Duplex
mode automatically.
© Polycom, Inc.
3 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Configuring IP Network Support
Use the following sections to configure the system so that you can place and
receive video calls using IP on your LAN or WAN:
❑ H.323 Settings, including Gatekeeper and Gateway
❑ SIP Settings
❑ Quality of Service
❑ Firewall or NAT
Specifying H.323 Settings
If your network uses a gatekeeper, the system can automatically register its H.323
name and extension. This allows others to call the system by entering the H.323
name or extension instead of the IP address.
To specify H.323 settings:
1. Go to System > Admin Settings > Network > IP > H.323 Settings.
2. Configure these settings:
Setting
Description
Enable IP H.323
Specifies whether to allow IP dialing.
Display H.323
Extension
Lets you place a gateway call by entering the H.323 extension
separately from the gateway ID.
If you do not check this box, you can make gateway calls by
entering the call information in this format:
gateway ID + TCS4 delimiter + extension
Check with your network provider to determine your TCS4
delimiter.
H.323 Name
Specifies the name that gatekeepers and gateways use to identify
this system. You can make point-to-point calls using H.323 names
if both systems are registered to a gatekeeper.
The H.323 Name is the same as the System Name, unless you
change it. Your dial plan may define the names you can use.
H.323 Extension
(E.164)
Lets you place point-to-point calls using the extension if both
systems are registered with a gatekeeper.
The default H.323 Extension is based on the system serial
number, but it can be changed. Your dial plan may define the
extensions you can use.
3 - 6
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Configuring Network Use
Configuring the System to Use a Gatekeeper
A gatekeeper supervises network traffic and manages functions such as
bandwidth control and admission control. The gatekeeper also handles address
translation, which allows you to make calls using static aliases instead of IP
addresses that may change each day.
To configure the system to use a gatekeeper:
1. Go to System > Admin Settings > Network > IP > H.323 Settings.
2. Select
and configure these settings:
Setting
Description
Use Gatekeeper
Specifies whether to use a gatekeeper. Gateways and
gatekeepers are required for calls between ISDN and IP networks.
•
•
•
Off — Calls do not use a gatekeeper.
Auto — System automatically finds an available gatekeeper.
Specify — Calls use the specified gatekeeper. Enter the
gatekeeper’s IP address or name (for example,
gatekeeper.companyname.usa.com or 255.255.255.255).
H.323 Name
Specifies the name that gatekeepers and gateways use to identify
this system. You can make point-to-point calls using H.323 names
if both systems are registered to a gatekeeper.
The H.323 Name is the same as the System Name, unless you
change it. Your dial plan may define the names you can use.
H.323 Extension
(E.164)
Lets you place point-to-point calls using the extension if both
systems are registered with a gatekeeper.
The default H.323 Extension is based on the system serial
number, but it can be changed. Your dial plan may define the
extensions you can use.
Outbound Call
Route
For systems using a gatekeeper, specifies whether calls initiated
by this system should be handled as IP calls sent through a
gateway or as ISDN.
Gatekeeper IP
Address
If you chose to use an automatically selected gatekeeper, this
area displays the gatekeeper’s IP address.
If you chose to specify a gatekeeper, enter the IP address here.
Alternate
Gatekeepers
If you chose to specify a gatekeeper, you can specify other
gatekeepers that the system can use if the primary gatekeeper is
not available.
© Polycom, Inc.
3 - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Configuring the System to Use a Gateway
A gateway performs code and protocol conversion between IP networks and
ISDN, so that users on different networks can call one another. If the system is
configured to use a gateway, you must also configure it to use a gatekeeper.
To configure the system to use a gateway:
1. Go to System > Admin Settings > Network > IP > H.323 Settings.
2. Select
twice and configure these settings:
Setting
Description
Country Code
Area Code
Number
Specifies the country code for the system’s location.
Specifies the area or city code for the system’s location.
Specifies the gateway’s number.
H.323 Extension
(E.164)
Lets you place point-to-point calls using the extension if both
systems are registered with a gatekeeper.
The default H.323 Extension is based on the system serial
number, but it can be changed.
Gateway Number
Type
Specifies the number type users enter to call this system:
•
Direct Inward Dial (DID) — Users enter an internal extension
to call this system directly.
NOTE: If you choose this option, you must also register the
number with the gatekeeper as an E.164 alias.
•
Number + Extension — Users enter the gateway number and
the system’s extension to call this system.
Number of Digits in
DID Number
Specifies the number of digits in the DID number.
The national or regional dialing plan for your location determines
the standard number of digits. For instance, the US standard is 7
digits.
Number of Digits in
Extension
Specifies the number of digits in the extension used when
Number + Extension is selected.
Your organization’s dial plan determines this number.
3. Select
and enter a prefix or suffix for each bandwidth you want to allow
for gateway calls.
Be sure to configure the gateway to use the same prefixes and suffixes you define for the
system.
3 - 8
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Configuring Network Use
Specifying SIP Settings
If your network supports the Session Initiation Protocol (SIP), you can use SIP to
connect IP calls.
To specify SIP Settings:
1. Go to System > Admin Settings > Network > IP > SIP Settings.
2. Configure these settings:
Setting
Description
Enable SIP
Allows the system to make calls using SIP.
Indicates the protocol the system uses for SIP signalling.
Transport Protocol
The SIP network infrastructure in which your V500 system is
operating determines which protocol is required. For example, if
your V500 system is operating in a Microsoft Live Communication
Server (LCS) SIP network, choose TCP. If your V500 system is
operating in a Nortel Multimedia Communication Server (MCS)
SIP network, choose UDP.
Password
Specifies the password that authenticates the system to the
Registrar Server.
User Name
Proxy Server
Specifies the system’s SIP name. If you leave this field blank, the
system’s IP address is the SIP user name.
Specifies the DNS name or IP address of the SIP Proxy Server. If
you leave this field blank, no proxy server is used.
By default, the SIP signalling is sent to port 5060 on the proxy
server. To specify a different port, add it to the address as shown
here:
255.255.255.255:5070
Registrar Server
Specifies the name or IP address of the SIP Registrar Server.
By default, the SIP signalling is sent to port 5060 on the registrar
server. To specify a different port, add it to the address as shown
here:
255.255.255.255:5070
© Polycom, Inc.
3 - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Specifying Quality of Service
Set the Quality of Service options for the way your network handles IP packets
during video calls.
To specify Quality of Service:
1. Go to System > Admin Settings > Network > IP > Quality of Service.
2. Configure these settings:
Setting
Description
Type of Service
Specifies your service type and lets you choose how to set the
priority of IP packets sent to the system for video, audio, and
far-end camera control:
•
IP Precedence — Represents the priority of IP packets sent to
the system. The value can be between 0 and 5. If this option is
selected, enter the value in the Type of Service Value field.
•
DiffServ — Represents a priority level between 0 and 63. If this
option is selected, enter the value in the Type of Service Value
field.
Type of Service
Value
Specifies the IP Precedence or Diffserv value for Video, Audio,
and Far-End Camera Control.
Enable PVEC
Allows the system to use PVEC (Polycom Video Error
Concealment) if packet loss occurs.
Dynamic
Bandwidth
Specifies whether to let the system automatically find the optimum
line speed for a call.
Maximum Transmit
Bandwidth
Specifies the maximum transmit line speed between 48 Kbps and
512 Kbps.
Maximum Receive
Bandwidth
Specifies the maximum receive line speed between 48 Kbps and
512 Kbps.
If the system is connected to the Internet via DSL or a cable modem, it is useful to set
maximums for transmitting and receiving bandwidth. DSL and cable modems typically allow
for faster download (receive) speeds compared to upload (transmit) speeds, and so these
settings provide an opportunity to regulate differences.
3 - 10
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Configuring Network Use
Configuring the System for Use with a Firewall or NAT
A firewall protects your network by controlling data traffic from outside the
network. Unless the firewall is designed to work with H.323 video conferencing
equipment, you must configure the system and the firewall to allow video
conferencing traffic to pass in and out of the network.
Network Address Translation (NAT) network environments use private internal IP
addresses for devices within the network, while using one external IP address to
allow devices on the LAN to communicate with other devices outside the LAN. If
your system is connected to a LAN that uses a NAT, you will need to enter the NAT
public (WAN) address so that your system can communicate outside the LAN.
To set up the system to work with a firewall or NAT:
1. Go to System > Admin Settings > Network > IP > Firewall.
2. Configure these settings:
Setting
Description
Fixed Ports
Lets you specify whether to define the TCP and UDP ports.
•
If the firewall is not H.323 compatible, enable this option. The
V500 system assigns a range of ports starting with the TCP
and UDP ports you specify. The system defaults to a range
beginning with port 3230 for both TCP and UDP.
NOTE: You must open the corresponding ports in the
firewall. You must also open the firewall’s TCP port 1720 to
allow H.323 traffic.
•
If the firewall is H.323 compatible or if the system is not
behind a firewall, disable this option.
TCP Ports
UDP Ports
Lets you specify the beginning value for the range of TCP and
UDP ports used by the system.
NOTE: You must also open the firewall’s TCP port 1720 to
allow H.323 traffic.
© Polycom, Inc.
3 - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Setting
Description
NAT Configuration
Lets you specify whether the system should determine the
NAT Public WAN Address automatically.
•
•
•
•
If the system is behind a NAT that allows HTTP traffic, select
Auto.
If the system is behind a NAT that does not allow HTTP
traffic, select Manual.
If the system is not behind a NAT or is connected to the IP
network through a Virtual Private Network (VPN), select Off.
If the system is behind a firewalled NAT router that is
UPnP™ (Universal Plug and Play) certified, select UPnP.
Many routers used in homes and small businesses support
UPnP NAT traversal. If this is your situation, try selecting
UPnP first. If this selection does not work for your router,
select Auto or Manual.
NAT Public (WAN)
Address
Displays the address that callers from outside the LAN use to
call your system. If you chose to configure the NAT manually,
enter the NAT Public Address here.
NAT is H.323
Compatible
Specifies that the system is behind a NAT that allows HTTP
traffic.
Address Displayed in
Global Directory
Lets you choose whether to display this system’s public or
private address in the Global Directory.
Configure the V500 system for specific products as follows:
If you use this type of
NAT or firewall:
Configure your V500 system this way:
Use Fixed Ports
System is
Behind a NAT
NAT is H.323
Compatible
Cisco® PIX®
Yes
Yes
No
NOTE: Do not select the
Fix Up H.323 feature.
Cisco® Router NAT
Linksys®
No
No
No
No
Yes
No
Yes
No
Setting is ignored
Netgear®
No
SMC® Barricade™
Yes
Yes
Systems deployed outside a firewall are potentially vulnerable to unauthorized access. Visit
also register to receive periodic email updates and advisories.
3 - 12
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Configuring Network Use
Configuring ISDN Support
The V500 system supports the BRI network interface for ISDN calling.
The system automatically detects the type of interface installed and displays only
the required configuration screens.
Configuring the BRI Network Interface
To configure the ISDN interface settings:
1. Go to System > Admin Settings > Network > ISDN.
2. Configure these settings:
Setting
Description
Enable ISDN H.320 Allows this system to make H.320 (ISDN) calls.
Outside Line
Dialing Prefix
Specifies the ISDN dialing prefix used to call outside the network.
ISDN Switch
Protocols
Specifies the protocol used by your network’s switch.
ISDN Voice
Algorithm
Specifies which voice algorithm (Alaw or uLaw) is used for ISDN
voice calls.
Do not change this setting unless you experience audio issues in
all ISDN voice calls.
Auto BRI
Configuration
Allows the NI-1 switch to automatically configure the directory
numbers and SPIDs.
This setting is only available if you have selected the NI-1 switch
protocol.
© Polycom, Inc.
3 - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
3. Select
and configure these settings:
Setting
Description
Area Code
Specifies the area code for this system’s location.
Directory Numbers
Specifies the numbers assigned to the B1 and B2 channels for the
BRI line.
The two numbers for a line may be the same or different,
depending on the switch protocol in use.
Enable
Specifies whether to enable the ISDN line.
If you selected the Standard ETSI Euro ISDN protocol, you must
enable the BRI line.
The ISDN BRI Numbers screen also displays the country selected as the
system’s location and the Country Code used for international calls to the
system. To specify the system’s location, go to System > Admin Settings >
General Settings > Location. The system automatically supplies the country
code when you specify the country.
4. If you have configured the ISDN switch protocol to be AT&T 5ESS Multipoint,
NI-1, or Nortel DMS-100, select
by your service provider.
and enter the ISDN BRI SPIDs provided
After you enter the SPIDs, the system verifies them. If the system is unable to
verify the SPIDs, make sure the system is connected and that the ISDN
numbers you entered are correct.
If you do not have the SPIDs from your service provider, you can click Start to
Auto-Detect SPIDs.
Configuring Call Preferences
Call preferences help you manage the network bandwidth used for calls. You can
specify the default and optional call settings for outgoing calls. You can also limit
the call speeds of incoming calls.
To choose call preferences:
1. Go to System > Admin Settings > Network > Call Preference.
3 - 14
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Configuring Network Use
2. Configure these settings:
Setting
Description
Enable H.329
Enable IP H.323
Enable SIP
Specifies standards-based People + Content data collaboration.
Allows the system to make IP calls.
Allows the system to use SIP when connecting IP calls.
Enable ISDN H.320 Allows the system to make ISDN calls.
Enable Voice Over
ISDN
Allows the system to make voice-only calls to phones connected
to an ISDN network, such as an organization’s PBX.
3. Select
to go to the Network Dialing screen and specify the dialing order
preference between IP and ISDN.
If the sites in your directory have both IP and ISDN numbers, these settings determine
your network preferences for placing the call.
4. Select
Setting
to go to the Preferred Speeds screens and configure these settings:
Description
PreferredSpeed for Determines the speeds that will be used for calls from this system
Placing Calls
when:
•
Call Quality is set to Auto on the home screen and Directory
screen
•
The Call Quality option is not available for users
If the far-end system does not support this quality, the system
automatically negotiates a lower quality.
Maximum Speed
Allows you to restrict the bandwidth used when receiving calls.
for Receiving Calls
If the far site attempts to call the system at a higher speed than
selected here, the call is re-negotiated at the speed specified in
this field.
5. Select
to go to the Call Speeds screen and specify the call speeds to make
available to users, if you are allowing them to choose speeds on a call-by-call
basis.
© Polycom, Inc.
3 - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Configuring the Global Directory
If you use the Polycom Global Management System, you can configure your
system to use the Global Directory. The Global Directory provides a list of other
systems that are registered with the Global Directory Server and are available for
calls. The other systems appear in the Directory, allowing you to place calls to other
users by selecting their names.
Configuring the Directory Server Settings
To configure the Directory Server settings:
1. Go to System > Admin Settings > Global Services > Directory Servers.
2. Configure these settings:
Setting
Description
Global Directory
(GDS)
Specifies the IP address or DNS address of the Global Directory
Server. You can enter up to five addresses.
Register
Registers this system with the Global Directory Server.
Lets you enter the Global Directory password, if there is one.
Displays other registered systems in the Global Directory.
Password
Display Global
Addresses
Display Name in
Global Directory
Specifies whether to display the system’s name in the Global
Directories of other registered systems.
Save Global
Copies the Global Directory to this local system.
Directory to System
3 - 16
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Configuring Network Use
Setting the Dialing Rules
If your system is connected to a private network and also to a public network, you
may need to specify the codes and prefixes necessary for dialing other systems.
To set the dialing rules:
1. Go to System > Admin Settings > Global Services > Dialing Rules.
2. Configure these settings:
Setting
Description
Always Dial Area
Code
Specifies that calls to sites in the same area code must include
the area code.
Dial 1+ for all USA
calls
Specifies that calls to systems in the United States must include
a “1” before the area code.
Placing a Test Call
When you finish configuring the system, you can use one of the sample numbers
in the directory to test your setup.
To place a test call:
1. On the Place a Call screen, select
.
2. Select Category.
3. Select Sample Sites and highlight a location.
4. Press on the remote control.
You can also find a list of worldwide numbers that you can use to test your V500 system at
© Polycom, Inc.
3 - 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
If you have trouble making video calls:
❑ Make sure the number you dialed is correct, then try the call again. For
example, you may need to dial 9 for an outside line or include a long distance
access code or country code.
❑ To find out if the problem exists in your system, ask the person you were trying
to reach to call you instead.
❑ Find out if the system you are calling has its power turned on and is
functioning properly.
❑ If you can make calls but not receive them, make sure that your system is
configured with the correct number.
Checking System Status
The System Status screen provides detailed information about system settings, IP
and ISDN connections, time server connections, and other information that is
important to the functioning of the system. For an explanation of any of the status
items, select the item and press
on the remote.
When there is a change in system status or a potential problem, you see an alert at
the bottom of the Place a Call screen.
To view System Status information:
>> Go to System > Diagnostics > System Status.
To get information about a status message:
>> Select the status message and press
or
on the remote control.
3 - 18
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 - Configuring Network Use
Keeping your Software Current
If you have Internet access, you can use the web-based Softupdate application to
upgrade the system software. If you do not have Internet access, your reseller can
supply you with the updated software on CD-ROM.
To upgrade your software via the Internet:
2. Log in to the Polycom Product Resource Center, find your product page, and
download the software update file in .zip format.
3. Double-click the software.zip file to extract the file.
4. Double-click Softupdate.exe.
5. Click Softupdate, then enter the IP address of the system you want to update.
Enter the administrator password, if required, and click OK to begin the
upgrade.
6. On the Options tab of the Softupdate application, select the other actions you
want to occur during the update:
•
•
Remove Address Book — Check this option to delete your existing
directory before the update.
Remove System Files — Check this option to delete your existing system
files before installing new system files.
7. Click Continue to upgrade the software.
Caution
Do not power off the system during the software upgrade process. If the upgrade is
interrupted, the system reverts to its original software version.
© Polycom, Inc.
3 - 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
3 - 20
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Designing the User Experience
Everybody who uses the Polycom V500 system has different needs. That’s why
your system has a customizable user interface. You can design the video
conferencing experience to meet your needs and the needs of any other users who
use the system.
You can customize the behavior of the system, and then build in various access
levels for the different users, depending on how much or how little you want them
to change system behaviors.
When you set up the system for the first time, the system is configured with the
most commonly used settings. If you need to change any of these initial settings,
you can adjust the screen settings as described in this chapter.
If you established an administrator’s password during the initial configuration,
you must enter it each time you change advanced settings.
What’s in this Chapter?
Page
© Polycom, Inc.
4 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Managing User Access to Settings and Features
You can manage access to various settings and features by using passwords and by
configuring the system to show only those options you want other users to see.
To maintain this
security level:
You can allow users to:
High
Call only the numbers you specify on the home screen.
(Kiosk mode)
Medium
Place calls using the restrictions you specify for length of call,
type of call, and use of the directory.
Low
Configure user settings.
Very low
Configure all system settings.
Setting the Admin Password
Set an administrator’s password to restrict who can:
❑ Make changes other than those in the User Settings screen
❑ Update the software
❑ Perform remote management using the V500 web interface
To set or change the Admin Password:
1. Go to System > Admin Settings > General Settings > Security.
2. Enter or change the password. You may use letters and numbers, but no other
characters.
4 - 2
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 - Designing the User Experience
To reset a forgotten Admin Password:
1. Get the system’s serial number from the system or from the System
Information screen.
2. Go to System >Diagnostics > Reset System.
3. Enter the system’s serial number and select Delete System Settings.
4. Select Reset System.
When the system completes the reset, it leads you through the setup wizard. You
can enter a new Admin Password when you set up the system.
Screens that Require the Admin Password for Access
The following diagram shows top-level system screens. All screens within Admin
Settings require the administrator’s password.
System Information
Utilities
Admin Settings
Diagnostics
User Settings
General Settings
System Settings
Network
Monitor
Camera
Audio
LAN Properties
Global Services
Directory Servers
Dialing Rules
HomeScreenSettings
Security
SNMP
Management Servers
Account Validation
My Information
Location
IP
H.323 Settings
SIP Settings
Quality of Service
Firewall
ISDN
Call Preference
Recent Calls
© Polycom, Inc.
4 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Letting Users Customize the Workspace
You can allow other users of the V500 system to change common user preferences
by providing access to the User Settings screen.
To allow users to customize the workspace:
1. Go to System > Admin Settings > General Settings > Security.
2. Check the Allow Access to User Settings option to make the User Settings
button available to users on the System screen.
User Settings contains the following options:
❑ Backlight Compensation
❑ Camera Brightness
❑ Meeting Password
❑ Auto-Answer Point to Point
❑ Mute Auto-Answer Calls
❑ PIP
❑ Keypad Audio Confirmation
❑ Color Scheme
❑ Far Site Name Display Time
❑ Dual Monitor Emulation
❑ Allow Video Display on Web
These options are also available to the administrator on the Admin Settings screens.
4 - 4
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 - Designing the User Experience
Limiting What Users Can Do With the System
You can limit what you allow other users to do with the system by configuring the
following:
❑ Maximum Time in Call — If you want to specify the maximum time a call can
last, go to System > Admin Settings > General Settings > System Settings >
Call Settings and enter the maximum call length allowed.
❑ Allow Directory Changes — If you do not want anyone to save changes to the
local directory of the system, go to System > Admin Settings > General
Settings > System Settings > Directory and clear this option.
Using the System for Specialized Applications
You can customize the system to show only a specific set of numbers to call. This
mode, also known as “kiosk mode,” can be used for specialized applications, such
as customer query stations or systems used for calling the same numbers on a
regular basis. Kiosk mode requires little or no training and instructions can be
incorporated into the screen design.
mode and its applications.
© Polycom, Inc.
4 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Designing Video Behaviors
You can configure the following video behaviors to accommodate your
environment:
❑ Camera Settings
❑ TV Monitor
❑ Dual Monitor Emulation
❑ Monitor’s Color Balance
Configuring Camera Settings
The Camera screen lets you specify camera settings.
To configure camera settings:
1. Go to System > Admin Settings > Camera.
2. Configure these settings:
Setting
Description
Backlight
Compensation
Specifies whether to have the camera automatically adjust for a
light background. Backlight compensation is best used in
situations where the subject appears darker than the background.
Camera
Brightness
Specifies how much light is let into the camera’s iris. A low number
allows in less light; a high number allows in more light.
4 - 6
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 - Designing the User Experience
Configuring the TV Monitor
The V500 system allows you to customize the display to suit your room and
equipment configuration.
To configure the TV monitor:
1. Go to System > Admin Settings > Monitor.
2. Configure these settings:
Setting
Description
Monitor
Specifies the monitor’s aspect ratio:
•
•
4:3 — Select if you are using a regular TV monitor.
16:9 — Select if you are using a wide screen monitor and
configuring for dual-monitor emulation.
You can set a wide-screen monitor to 16:9 to resize the UI screens
even if you do not configure it for dual-monitor emulation. The
far-site video is displayed in the same way for both settings.
NOTE: If you select 16:9, you will also need to set up the monitor for
full-screen display. In the monitor’s setup menu, choose the setting
that stretches the picture uniformly without clipping the edges.
Use this setting:
Not this setting:
PIP
Specifies PIP (Picture-in-Picture) behavior:
•
•
•
On — The PIP window stays on for the duration of the call.
Off — The PIP window is not displayed during the call.
Auto — The PIP window is displayed when a user picks up the
remote.
NOTE: PIP settings are also available in the User Settings screen.
Users can turn the PIP on or off and change its location on the
screen using the PIP button on the remote control.
Display Icons in a
Call
Specifies whether to display all on-screen graphics, including icons
and help text, during calls.
Snapshot
Timeout
Lets you choose whether to have snapshots time out after a period
of four minutes, after which the system returns to live video.
If you want to return to live video before four minutes have elapsed,
press the Near button on the remote control twice.
Dual Monitor
Emulation
Specifies whether both sites are displayed in a split-screen mode
when using one monitor.
© Polycom, Inc.
4 - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Using Dual Monitor Emulation
With Dual Monitor Emulation, you see both near and far sites on one monitor in two
different views. During presentations, you see content and the near and far sites.
Setting Up
On the monitor’s setup menu, select the full-screen setting that
stretches the picture uniformly, without clipping.
On the TV Monitor screen:
1. If you are using a wide screen monitor, set Monitor to 16:9.
Otherwise, set Monitor to 4:3.
2. Select Dual Monitor Emulation.
Using in a Call
Call connects
Near and far site are the same size
and appear side by side.
Far site
Near site
Near site presses PIP
Size of far site window increases.
Far site presents to near site
Content, near site, and far site are displayed in
dual monitor emulation mode.
4 - 8
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 - Designing the User Experience
Adjusting the Monitor’s Color Balance
In most cases, the monitor you connect to your system provides natural color
without any adjustment. Depending on your environment as well as the model of
monitor, however, the video may exhibit one of these problems:
❑ Picture is too dark
❑ Colors appear faded
❑ Picture has too much of one color — for example, the picture may appear
greenish
If you notice any of these, the monitor needs to be adjusted.
To adjust the monitor for natural color:
1. Go to System > Diagnostics > Video.
2. Select the Color Bars icon to display the color bar test screen.
3. Adjust the color using the monitor’s controls for color, contrast, and
brightness. Your monitor may also have controls for tint and temperature.
4. When the colors look right on the test screen, press the
Near button on the
remote control to stop the Color Bars test and show video of the room.
5. If the color appears natural, you do not need to make further adjustments.
If the color still needs adjustment, use the monitor’s controls to make small
adjustments until the picture appears natural.
Designing Audio Behaviors
This section describes how to configure the audio behaviors of the V500 system,
including:
❑ General Audio Settings
❑ Volume on an External Audio System
© Polycom, Inc.
4 - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Configuring General Audio Settings
To configure general audio settings:
1. Go to System > Admin Settings > Audio.
2. Configure these settings:
Setting
Description
Master Audio Volume
Sets the volume level for audio from the far site.
Sets the volume level of the ring tone and user alert tones.
Sound Effects
Volume
Incoming Video Call
User Alert Tones
Bass
Specifies the ring tone used for incoming calls.
Specifies the tone used for user alerts.
Sets the volume level for the lower frequencies without changing
the master audio volume.
Treble
Sets the volume level for the higher frequencies without
changing the master audio volume.
Mute Auto-Answer
Calls
Specifies whether to mute incoming calls.
If you select this option, incoming calls are muted until you press
the Mute button on the remote control.
Enable Internal
Ringer
Specifies an additional ring tone when receiving an incoming
call.
The ringer is built into the system and will alert you to incoming
calls even if the TV monitor connected to the system is powered
off.
Setting the Volume on an External Audio System
If you have connected an external audio system, you may need to adjust its
volume.
To set the volume:
1. Go to System > Diagnostics > Audio > Speaker Test.
2. Adjust the external audio system’s volume so that the tone is as loud as a
person talking in the room.
After you do this, you can adjust volume levels using the V500 system’s remote
control.
4 - 10
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 - Designing the User Experience
Designing General System Behaviors
You can configure the following general system behaviors to accommodate the
needs of your organization:
❑ Call Settings
❑ Remote Control Behavior
❑ Directory Settings
❑ Call Answering Mode
❑ AES Encryption
❑ Passwords and Security Options
❑ Date, Time, and System Location
Configuring Call Settings
The Call Settings screens provide access to high-level options for the entire system.
For convenience, some of the User Settings options are repeated on these screens.
To configure call settings:
1. Go to System > Admin Settings > General Settings > System Settings > Call
Settings.
2. Configure these settings:
Setting
Description
Maximum Time in
Call
Enter the maximum number of minutes allowed for call length.
When that time has expired, you see a message asking you if you
want to hang up or stay in the call. If you do not answer within one
minute, the call automatically disconnects. If you choose to stay
in the call at this time, you will not be prompted again.
Auto-Answer Point
to Point
Specifies whether to answer incoming point-to-point calls
automatically.
Display Time in Call Specifies whether to display the elapsed time or the local time
during a call. You can also choose not to display the time.
Call Detail Report
Specifies whether to generate a report of all calls made with the
system. When selected, details for all calls can be viewed via the
V500 web interface and downloaded as a .csv file.
© Polycom, Inc.
4 - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Setting
Description
Recent Calls
Specifies whether to display the Recent Calls button on the home
screen. The Recent Calls screen lists the site number or name,
the date and time, and whether the call was incoming or outgoing.
NOTE: If the Call Detail Report option is not selected, the Recent
Calls option is not available.
Far Site Name
Display Time
Specifies the time period the far-site name appears on screen
when calls first connect.
Configuring Remote Control Behavior
You can customize the behavior of the remote control to support the your
environment.
To configure remote control behavior:
1. Go to System > Admin Settings > General Settings > System Settings >
Remote Control.
2. Configure these settings:
Setting
Description
Keypad Audio
Confirmation
Specifies whether to play a voice confirmation of numbers
selected with the remote control.
Remote Control
Keypad
Specifies whether the camera moves to presets or creates DTMF
tones when the remote control keypad buttons are pressed.
Configuring Directory Settings
You can customize the behavior of the Directory on the Directory screen.
To configure system settings:
1. Go to System > Admin Settings > General Settings > System Settings >
Directory.
2. Configure these settings:
Setting
Description
System Name
Enter or change the system name in this field. This name appears
on the screen for the far site when you are making calls.
Allow Directory
Changes
Specifies whether you can save changes you make to the
directory.
4 - 12
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 - Designing the User Experience
Setting
Description
Confirm Directory
Additions
Specifies whether you are prompted to confirm new directory
entries when saving the information for the last site called.
Confirm Directory
Deletions
Specifies whether you are prompted to confirm deletions of
directory entries.
Setting the Call Answering Mode
You can choose to answer calls automatically or manually, or you can set the
system to automatically refuse any incoming calls.
To set the call answering mode:
1. Go to System > Admin Settings > General Settings > System Settings > Call
Settings.
2. Select Auto-Answer Point to Point.
3. Select one of the following:
•
•
•
Yes – Answers calls automatically.
No – Enables you to answer calls manually.
Do Not Disturb – Refuses incoming calls automatically. The caller receives
a message that the site is unavailable.
Automatically answering calls is convenient, but keep in mind that an unexpected caller
could interrupt you or see and hear you without your knowledge. If you still want to
automatically answer calls but you want to prevent incoming callers from seeing and hearing
you, you can choose to mute all automatically answered calls and make sure your lens cover
is closed.
Enabling AES Encryption
AES encryption is a standard feature on all V500 systems.
To enable AES encryption:
>> Go to System > Admin Settings > General Settings > Security and select AES
Encryption.
© Polycom, Inc.
4 - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Setting Passwords and Security Options
You can enter or change the administrator and meeting passwords as well as
specify whether to allow remote access to the system.
To set passwords and security options:
1. Go to System > Admin Settings > General Settings > Security.
2. Configure these settings:
Setting
Description
Admin Password
Enter or change the Admin password.
When the Admin password is set, you must enter this password
to:
•
•
•
Make configuration changes not in the User Settings screen.
Update the software.
Manage the system using the V500 web interface.
Meeting Password
Enter or change the meeting password, if any.
Allow Access to
User Settings
Specifies whether the User Settings screen is accessible to users
via the System screen.
Uncheck this option if you do not want users to change
environmental settings.
AES Encryption
Specifies whether to encrypt calls with other sites that support
AES encryption.
Enable Remote
Access
Specifies whether to allow remote access to the system by:
•
•
•
•
FTP
Web
Telnet
SNMP
You may select any of these, or any combination of them.
NOTE: The system reboots if you change the remote access
settings.
Web Access Port
Specifies the port to use when accessing the system using the
V500 web interface.
If you change this from the default (port 80), you will need to
include the port number with the IP address when you use the
V500 web interface to access the system. This makes
unauthorized access more difficult.
Allow Video Display
on Web
Specifies whether to allow administrators to view the room where
the system is located using the V500 web interface.
4 - 14
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 - Designing the User Experience
Setting Date, Time, and Location
You can update the system with regional settings, including the location-specific
language and calling parameters.
To set the date, time, and location:
1. Go to System > Admin Settings > General Settings > Location.
2. Configure these settings:
Setting
Description
Country
Specifies the country where the system is located.
Changing the country automatically adjusts the country code
associated with your system number.
Language
Sets the language for the user interface.
Country Code
Area Code Required
Specifies the country code for the system location.
Specifies if an area code is required to place ISDN calls in the
specified country.
ISDN International
Access
Specifies the international code required for placing ISDN calls
from the system location to another country.
Room Telephone
Number
Indicates the telephone number of the room where the system is
located.
3. Select
and configure these settings:
Setting
Description
Date Format and
Time Format
Specifies your format preference for the date and time display
and lets you enter your local date and time.
Daylight Saving Time Specifies whether it is daylight saving time.
Time Difference from
GMT
Specifies the time difference between GMT (Greenwich Mean
Time) and your location.
Display Time in Call
Specifies the time display in a call:
•
•
Elapsed Time – Displays the amount of time in the call.
Local Time – Displays the local time on the screen during a
call.
•
Off – Time is not displayed.
Time Server
Specifies connection to a time server for automatic system time
settings.
© Polycom, Inc.
4 - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Customizing the Workspace Appearance
You can customize the V500 system workspace appearance to suit your
environment functionally and aesthetically.
For example, by customizing the home screen into kiosk mode, anyone who uses
the system only has to select a site and press the
Call button on the remote
control to place a call.
Use the following sections to configure the general appearance of the system:
❑ Designing the Home screen
❑ Adding Sites to the Home screen
❑ Adding On-screen Instructions
❑ Changing Color Schemes
❑ Setting Ring Tones and Alert Tones
4 - 16
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 - Designing the User Experience
Designing the Home Screen
Customize the system functionality according to your needs, skill level, and environment.
Use the marquee to
add instructions
Infrequent Users (Kiosk Mode)
Provide a simple workspace so no training is
needed:
•
Let users make calls to pre-defined
numbers with one button click.
Include a short
list of specific
items for users
to select
•
Include instructions on screen.
New Users
Provide more options but keep it simple:
•
•
•
Dialing entry field
Directory numbers
Recent Calls
Add features
for users
as needed
Advanced Users
Provide additional options for advanced video
conferencing users:
•
Call Quality
Add more
features as
users gain
experience
•
User Settings, Diagnostics, and System
Information
•
Speed Dial list of frequently called sites
© Polycom, Inc.
4 - 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
To design the home screen:
1. Go to System > Admin Settings > General Settings > Home Screen Settings.
2. Configure these settings:
Setting
Description
Dialing Display
Specifies which dialing option to display:
•
•
Dialing entry field — Allows users to enter numbers manually.
Display marquee — Displays text in the dialing entry field. Can
be used to display user instructions. Users cannot enter numbers
manually when this option is selected.
•
None — Removes the dialing entry field from the screen.
Call Quality
Allows users to select the bandwidth for calls.
H.323 Extension
(E.164)
Allows users to enter extensions on the home screen.
Directory
System
Allows users to access the directory.
Allows users to access the System screen, which includes User
Settings, Diagnostics, and System Information.
If you remove the System button, you can still access the System screen by navigating to
the home screen, pressing Help on the remote, and selecting System.
3. Select
and configure these settings:
Description
Setting
System Name
Specifies whether to display the name of the system on the home
screen above the PIP window.
IP or ISDN
Information
Specifies whether to display the system’s IP address, ISDN number,
or both on the home screen.
Local Date and
Time
Specifies whether to display the local date and time on the home
screen.
Do Not Disturb
Icon
Allows users to set the system to automatically accept or ignore
incoming calls using the Do Not Disturb button on the home screen.
Call Detail Report Specifies whether to generate a report of all calls made with the
system. When selected, all calls can be viewed through the web
interface and downloaded as a .csv file.
Recent Calls
Allows users to access a list of recent calls made with the system by
displaying the Recent Calls button on the home screen.
If the Call Detail Report option is not selected, the Recent Calls
option is not available.
4 - 18
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 - Designing the User Experience
4. Select
and configure these settings:
Setting
Description
Sites
Allows users to access any pre-defined sites from a My
Contacts/Speed Dial list on the home screen.
Last Number
Dialed
Specifies whether to display the last number dialed or clear the
address box on the home screen.
Adding Sites to the Home Screen
Creating Site buttons on the home screen makes it easy for you to place calls to sites
that you call on a regular basis.
Sites can appear as individual buttons or as part of a list called Speed Dial or My
Contacts.
You must enter the site information in the directory before creating specific Site buttons for
the home screen.
To add sites on the Home screen:
1. Go to System > Admin Settings > General Settings > Home Screen Settings.
2. Select
three times to access the Sites screen.
3. Select Add and choose the sites to add from the directory.
4. Select either Speed Dial or Contacts as the name you want to appear on the
button.
© Polycom, Inc.
4 - 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Adding On-screen Instructions
Using Marquee Text
You can create marquee text to display in the dialing entry field on the home
screen. You can create context-specific instructions or, if the home screen has Site
buttons, the marquee text can provide information that helps other users choose
which site to call.
To enter marquee text:
1. Go to System > Admin Settings > General Settings > Home Screen Settings.
2. In Dialing Display, select Display Marquee and enter the text.
You can also add marquee text through the V500 web interface.
Using Screen Saver Text
You can customize the V500 system to display text when the system is in sleep
mode. For instance, you can display on-screen instructions.
To enter screen saver text:
1. On a PC, open a web browser.
2. In the browser address line, enter the system’s IP address (for example,
http://255.255.255.255) to go to the V500 web interface.
3. Enter your user name and the password, if a password has been established.
4. Click System Setup > Utilities > Screen Saver and enter:
•
•
Text — Appears as scrolling text when the system is in sleep mode. You
can use this scrolling text to provide instructions or next steps for users of
the system.
Logo Text — Appears underneath the logo before the system goes into
sleep mode.
5. Click Update.
4 - 20
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 - Designing the User Experience
Changing System Appearance
Different user interface color schemes are available, allowing you to coordinate the
system interface with the room décor.
To change the color scheme:
1. Go to System > Admin Settings > General Settings > System Settings >
Appearance.
2. Configure these settings:
Setting
Description
Color Scheme
Customizes the look of your system with different color schemes.
Screen Saver Wait
Time
Specifies how long the system remains awake during periods of
inactivity. The default is 3 minutes.
You can allow users to change color schemes by allowing user access to the User
Settings screen.
Setting Ring Tones and Alert Tones
To set ring tones and alert tones:
1. Go to System > Admin Settings > Audio.
2. Select a tone, as desired.
To set the V500 system’s internal ringer:
1. Go to System > Admin Settings > Audio.
2. Select Enable Internal Ringer to specify an additional ring tone when
receiving an incoming call.
The ringer is built into the system and will alert you to incoming calls even if the TV
monitor connected to the system is powered off.
© Polycom, Inc.
4 - 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Configuring Closed Captioning
You can provide real-time text transcriptions or language translations of the video
conference by displaying closed captions on your system. When you provide
captions for a conference, the captioner uses a web browser to listen to the
conference audio and enter the caption text in the system’s web interface. When
the captioner sends a unit of text, all sites see it on the main monitor for 15 seconds.
The text then disappears automatically.
Audio Options for Closed Captioners
When you provide captions for a conference, the captioner may be present, or may
use a telephone or web browser to listen to the conference audio.
The captioner must receive audio from the conference in one of these ways:
•
•
•
Attending one of the conferences sites
Listening to the conference via the V500 web interface
Listening to the conference via a speakerphone in the room at one of the
sites
Options for Supplying Closed Captions to Conferences
Captions can be provided in any language that uses the Latin alphabet.
The captioner can enter caption text in one of these ways:
•
•
In the room or remotely, using the V500 web interface
In the room or remotely, using a Telnet session
4 - 22
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 - Designing the User Experience
Providing Captions Via the V500 Web Interface
Closed captioners can provide captions from inside the conference room, or from
a remote location, by entering the captions directly into the V500 web interface, as
shown in the diagram below.
V500 System
Web interface
LAN
LAN port
To supply closed captions for a conference using the V500 web interface:
1. On a PC, open a web browser.
2. In the browser address line, enter the IP address of the system (for example,
http://255.255.255.255) to go to the system’s web interface.
3. Go to System Setup > Utilities > Closed Caption.
4. Enter your user name and the password, if a password has been established.
5. In the Closed Caption screen, type the caption text into the text field. Text
wraps to the next line after 59 characters.
6. Press Enter to send the text to the sites in the conference.
© Polycom, Inc.
4 - 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Providing Captions Via a Telnet Session
Closed captioners can provide captions from inside the conference room, or from
a remote location, by entering captions via a Telnet session, as shown in the
diagram below:
V500 System
Telnet session
LAN
LAN port
To supply closed captions for a conference using a Telnet session:
1. On a PC, open a command line interface.
2. Start a Telnet session using the V500 system’s IP address and port 24 (for
example, telnet 255.255.255.24).
3. Enter the command cc to start captioning.
4. Press Enter to send the text.
5. To stop sending closed captions, press CTRL-Z.
4 - 24
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 - Designing the User Experience
Getting Started with Calling
The system is installed and you’ve finished the network configuration and
designed the behaviors. Now it’s time for you to start placing calls. You may want
to spend time becoming familiar with basic calling tasks.
The following resources are available:
❑ V500 System Getting Started Guide — This guide is for all users, from beginners
to the more experienced. It covers meeting basics, different ways to place calls,
how to use the remote control, and how to deliver presentations.
It is included on the V500 system documentation CD and is also available on
the web.
❑ Screen Help — The home and Directory screens have context-specific help.
Users can press
on the remote control to access help topics.
documentation page on the Polycom website for the latest documents
supporting these products.
© Polycom, Inc.
4 - 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
4 - 26
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Managing the System Remotely
You configure, manage, and monitor the system from a remote computer using the
V500 web interface (the system’s web interface), the Polycom Global Management
System, or SNMP.
Your choice of management tool depends on your network environment:
❑ V500 web interface requires only a web browser to control the system.
❑ Polycom Global Management System requires the GMS application to be
installed on your network.
❑ SNMP requires network management software on your network management
station.
What’s in this Chapter?
Page
© Polycom, Inc.
5 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Using the V500 Web Interface
You can use the web interface to perform most of the calling and configuration
tasks you can perform on the local system.
Accessing the V500 Web Interface
To configure your browser to use the web interface:
1. Be sure that your web browser uses Microsoft Internet Explorer 6.0 or later.
2. Configure these settings:
•
•
Allow cookies: Enabled
Force pages to reload on every visit to a page: Enabled
To access the system using the web interface:
1. On a PC, open a web browser.
2. In the browser address line, enter the system’s IP address (for example,
http://255.255.255.255) to go to V500 web interface.
3. Enter adminas the user name, and the password, if a password has been
established.
You can use the web interface to configure all of the system settings except the remote
management settings. For security reasons, these settings must be configured on the local
system by an administrator.
5 - 2
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 - Managing the System Remotely
Managing System Profiles with the V500 Web Interface
The customization options for V500 systems have been extended with the ability
to store your system settings as separate profiles. Profiles can be stored on your PC
as a .csv file using the V500 web interface. There is no limit to the number of
profiles you can save.
This is particularly useful if you are managing systems that support multiple
applications. Changing the interface and behaviors of the V500 system can be done
quickly and easily.
The following settings are included in a profile:
•
•
•
•
•
Home Screen settings
User access levels
Icon selections
Option keys
System behaviors
Polycom recommends using profiles as a way to back up system settings. Attempting to edit
a stored profile or upload it to a different system can result in unexpected problems.
To store a profile:
1. In the V500 web interface, go to System Setup > Utilities > Profile Center.
2. Click V500 -> PC to download the .csv file from the V500 system.
3. Save the file to a location on your PC.
To upload a profile:
1. In the V500 web interface, go to System Setup > Utilities > Profile Center.
2. Click Browse and browse to the location of the .csv file on your PC.
3. Click PC -> V500 to upload the .csv file to your system.
© Polycom, Inc.
5 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Managing Directories with the V500 Web Interface
The V500 web interface’s import/export directory feature allows you to efficiently
maintain consistency of V500 system directories. It is particularly useful if you are
managing multiple systems that call the same locations. You can:
❑ Transfer existing directory entries between V500 systems
❑ Develop directory entries on one system, save them to your PC, and then
distribute them to other systems
Only local directories can be downloaded. The directory file is in .csv format.
To download a V500 system directory to your PC:
1. In the V500 web interface, go to System Setup > Utilities > Import Directory.
2. Click V500 -> PC to download the .csv file from the V500 system.
3. Save the file to a location on your PC.
To upload V500 system directory entries:
1. In the V500 web interface, go to System Setup > Utilities > Import Directory.
2. Click PC -> V500.
3. Click Browse and browse to the location of the .csv file on your PC.
4. Click Export Directory to upload the .csv file to the V500 system.
5 - 4
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 - Managing the System Remotely
Configuring Global Services
If you use the Polycom Global Management System, you can configure, manage,
and monitor the V500 system using the Global Management System (GMS) server.
GMS is a web-based client/server software tool that allows administrators to
manage a network of video conferencing systems.
To use global services for the system, configure the following:
❑ Management Servers
❑ Account Numbers
❑ My Information
Viewing the Management Servers List
On networks managed by the Global Management System, several Global Servers
may be configured to manage this system remotely. The system also has a primary
Global Management System server that performs account validation. You can view
information about these servers, but this information can only be changed by the
GMS Administrator.
To view the management servers list:
>> Go to System > Admin Settings > Global Services > Management Servers.
© Polycom, Inc.
5 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Requiring an Account Number for Calls
If your system is set up for use with the Global Management System, the system
can prompt you to enter an account number before placing a call. The account
number is added to the Global Management System’s Call Detail Record (CDR),
and this information can be used for call tracking and billing purposes.
If you configure the system to validate the account number, calls placed without a
valid account number are not completed. If you do not configure the system to
validate account numbers, calls are completed regardless of whether the account
number is valid. Account numbers are set up in the Global Management System
by the Global Management System administrator.
For more information about account validation, please contact your Global
Management System administrator.
To require an account number for calls:
1. Go to System > Admin Settings > Global Services > Account Validation.
2. Specify whether to require an account number for placing calls and whether
that number should be validated by the Global Management System server.
Adding My Information
If your system is managed by the Global Management System, you can configure
the V500 system so that you can request help from the Global Management System
administrator.
To add information for the Global Management System administrator:
1. Go to System > Admin Settings > Global Services > My Information.
2. Enter the contact information for the Global Management System
administrator for technical support.
The following section illustrates the interaction between Global Management
System and the system you are configuring.
5 - 6
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 - Managing the System Remotely
Requesting Technical Support from the GM S Administrator
1. From the Place A Call screen, press
on the remote.
2. Select Support and press
on the remote.
You see the following message:
Tech Support will be alerted to phone you at the
following number. Continue?
Enter your contact telephone number.
The V500 system sends your information to
the Global Management System.
The GMS administrator opens the
You see the following message:
alert message containing your
telephone number.
Tech Support has been alerted. You can also call
this number for assistance.
The message displays the telephone number you
entered for Tech Support on the My Information screen.
GMS sends a message to your
V500 system.
The V500 system displays the message from GMS:
Your request for help has been acknowledged.
The GMS administrator calls you.
© Polycom, Inc.
5 - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Setting Up SNMP
The V500 system sends SNMP (Simple Network Management Protocol) reports to
indicate a total of 31 conditions, including the following:
•
•
•
•
•
•
•
•
All alert conditions found on the V500 system’s alert page
Details of jitter, latency, and packet loss
Low battery power is detected in the remote control
A system powers on after a long period powered off
Administrator logon is successful or unsuccessful
A call fails for a reason other than a busy line
A user requests help
A telephone or video call connects or disconnects
Downloading MIBs
Before you can perform SNMP reporting, you need to install Polycom MIBs on the
computer you intend to use as your network management station.
The MIBs are available for download from the V500 web interface.
To download the Polycom MIBs:
1. On a PC, open a web browser.
2. In the browser address line, enter the IP address of the system (for example,
http://255.255.255.255) to go to the system’s web interface.
3. Go to Admin Settings > Global Services > SNMP.
4. Click Download MIB and follow the onscreen instructions.
5 - 8
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 - Managing the System Remotely
Configuring for SNMP Management
To configure the V500 system for SNMP management:
1. In the V500 web interface or from the V500 system, go to Admin Settings >
Global Services > SNMP.
2. Configure these settings:
Setting
Description
Enable SNMP
Allows administrators to manage the system remotely using
SNMP.
SNMP Community
Specifies the SNMP management community in which you want
to enable this system. The default community is public.
SNMP Contact
Name
Specifies the name of the person responsible for remote
management of this system.
SNMP Location
Name
Specifies the location of the system. The default is
your system name@your country name.
SNMP System
Description
Specifies the type of video conferencing device. This is a
display-only field.
SNMP Console IP
Address
Specifies the IP address of the SNMP traps sent by the system.
Enter 0.0.0.0in this field if any SNMP management console
is capable of receiving information from this agent.
© Polycom, Inc.
5 - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
5 - 10
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
6
System Usage and Statistics
The V500 system provides various screens that allow you to review information
about calls made by the system and to review network usage and performance.
What’s in this Chapter?
Page
© Polycom, Inc.
6 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Call Summary
The Call Summary screen provides details about the calls placed by the system,
including:
❑ Duration of the last call
❑ Total number of calls placed and received
❑ Number, total time, and percentage of IP calls
❑ Number, total time, and percentage of ISDN calls
To view the Call Summary screen:
>> Go to System > Diagnostics > Call Statistics and then select
three times.
You can view Call Statistics and Call Summary during a call by pressing
on the remote.
6 - 2
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 - System Usage and Statistics
Call Statistics
The two Call Statistics screens provide information about the call in progress,
including:
This screen:
Displays this information:
Call Statistics (1)
•
•
Call speed (transmit and receive)
Video protocol, annexes, and format in use (transmit and
receive)a
•
•
Audio protocol in use (transmit and receive)
Number of packets lost and percentage packet loss (transmit
and receive) in IP calls
•
Encryption type, key exchange algorithm type, and key
exchange check code (if the encryption option is enabled and
the call is encrypted)
•
Far site details and call type
Call Statistics (2)
•
•
•
•
•
Audio and video data rates specified (transmit and receive)
Video data rate and frame rate in use (transmit and receive)
Video packet loss and jitter in IP calls
Audio packet loss and jitter in IP calls
Far site details and call type
a. The video protocol is shown in green if the system is currently using error
concealment.
To view the Call Statistics screen:
>> Go to System > Diagnostics > Call Statistics and then select
.
You can view Call Statistics and Call Summary during a call by pressing
on the remote.
© Polycom, Inc.
6 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Call Status
The Call Status screen provides call connection information. The spheres on the
screen provide details for each line. When you place a call, you’ll see the status
change as the call connects.
To view the Call Status screen:
>> Go to System > Diagnostics > Call Statistics.
You can highlight the spheres on this screen to see the number dialed, the relevant
status code, and details of any errors.
You can view Call Status during a call by pressing
on the remote.
6 - 4
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 - System Usage and Statistics
Recent Calls
Recent Calls shows a list of up to 99 calls made by the system. It includes the
following information:
❑ Site name or number
❑ Date
❑ Time
❑ Call In or Out
The Recent Calls list shows incoming and outgoing calls that connect, as well as
outgoing calls that do not connect.
If Do Not Disturb has been enabled, any incoming calls attempted by other sites
will not be listed.
The Home screen can be configured to include Recent Calls. For more information about
including the Recent Calls list on the home screen, see Designing the Home Screen on
To view the Recent Calls screen:
>> Go to System > Admin Settings > Network > Recent Calls.
You can see more detail about any call by selecting an entry and pressing
on
the remote. Information includes the far site’s number and name, and the type,
speed (bandwidth), and duration of the call.
You can call any site on the Recent Calls list by highlighting the entry and pressing
or
on the remote to place the call.
If you need even more detail about calls, you can download the Call Detail Report (CDR)
from the V500 web interface. For more information about the CDR, see Call Detail Report
© Polycom, Inc.
6 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Call Detail Report
The Call Detail Report (CDR) provides the system’s call history. You can view the
CDR from the V500 web interface, and you can download the data in CSV format
for sorting and formatting.
CSV stands for Comma Separated Value. CSV files can be imported into spreadsheet and
database programs.
Every call that connects is added to the CDR, whether it is a call that you make or
that you receive. If a call does not connect, the report shows the reason.
The CDR does not include incoming calls that the V500 system does not answer, so
if calls were missed while Do Not Disturb was enabled, details will not be included
in the CDR.
To view and download the CDR via the V500 web interface:
1. On a PC, open a web browser.
2. In the browser address line, enter the system’s IP address (for example,
http://255.255.255.255) to go to V500 web interface.
3. Enter your user name and the password, if a password has been established.
4. Click System Setup > Utilities > Call Detail Report to view the details of the
file.
5. Click Save and then specify a location on your computer to save the file.
Information in the Call Detail Report
The following table describes the data fields in the CDR.
Data
Description
Row ID
Each call is logged on the first available row.
The call start date, in the format dd-mmm-yyyy.
The call start time, in the 24-hour format hh:mm:ss.
The call end date.
Start Date
Start Time
End Date
End Time
Call Duration
The call end time.
The length of the call.
6 - 6
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 - System Usage and Statistics
Data
Description
Account Number
If Require Account Number to Dial is enabled on the system, the
value entered by the user is displayed in this field.
Remote System
Name
The far site’s system name.
Call Field Number
1
The number dialed from the first call field, not necessarily the
transport address.
For incoming calls — The caller ID information from the first
number received from a far site.
Call Field Number
2 (if applicable for
call)
For outgoing calls — The number dialed from the second call field,
not necessarily the transport address.
For incoming calls — The caller ID information from the second
number received from a far site.
Transport Type
Call Rate
The type of call — Either H.320 (ISDN) or H.323 (IP).
The bandwidth negotiated with the far site.
System
Manufacturer
The name of the system manufacturer, model, and software
version, if they can be determined.
Call Direction
In — For calls received.
Out — For calls placed from the system.
Conference ID
Call ID
A number given to each conference.
Identifies individual calls within the same conference.
The total number of ISDN B channels used in the call.
Total H.320
Channels Used
Endpoint Alias
The alias of the far site.
Endpoint
An additional alias of the far site.
Additional Alias
Endpoint Type
Terminal, gateway, or MCU.
Endpoint
The actual address of the far site (not necessarily the address
Transport Address dialed).
Audio Protocol
(Tx)
The audio protocol transmitted to the far site, such as G.728.
Audio Protocol
(Rx)
The audio protocol received from the far site, such as G.728 or
G.722.
Video Protocol
(Tx)
The video protocol transmitted to the far site, such as H.263 or
H.264.
Video Protocol
(Rx)
The video protocol received from the far site, such as H.261 or
H.263.
Video Format (Tx)
The video format transmitted to the far site, such as CIF or SIF.
Video Format (Rx) The video format received from the far site, such as CIF or SIF.
© Polycom, Inc.
6 - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Data
Description
Disconnect
Reason
The description of the Q.850 (ISDN) cause code showing how the
call ended.
Q.850 Cause
Code
The Q.850 cause code showing how the call ended.
Total H.320 Errors
The number of errors during an H.320 call.
AveragePercentof The combined average of the percentage of both audio and video
Packet Loss (Tx)
packets transmitted that were lost during the 5 seconds preceding
the moment at which a sample was taken. This value does not
report a cumulative average for the entire H.323 call. However, it
does report an average of the sampled values.
AveragePercentof The combined average of the percentage of both audio and video
Packet Loss (Rx)
packets received that were lost during the 5 seconds preceding the
moment at which a sample was taken. This value does not report
a cumulative average for the entire H.323 call. However, it does
report an average of the sampled values.
Average Packets
Lost (Tx)
The number of packets transmitted that were lost during an H.323
call.
Average Packets
Lost (Rx)
The number of packets from the far site that were lost during an
H.323 call.
Average Latency
(Tx)
The average latency of packets transmitted during an H.323 call
based on round-trip delay, calculated from sample tests done once
per minute.
Average Latency
(Rx)
The average latency of packets received during an H.323 call
based on round-trip delay, calculated from sample tests done once
per minute.
Maximum Latency
(Tx)
The maximum latency for packets transmitted during an H.323 call
based on round-trip delay, calculated from sample tests done once
per minute.
Maximum Latency
(Rx)
The maximum latency for packets received during an H.323 call
based on round-trip delay, calculated from sample tests done once
per minute.
Average Jitter (Tx) The average jitter of packets transmitted during an H.323 call,
calculated from sample tests done once per minute.
Average Jitter (Rx) The average jitter of packets received during an H.323 call,
calculated from sample tests done once per minute.
Maximum Jitter
(Tx)
The maximum jitter of packets transmitted during an H.323 call,
calculated from sample tests done once per minute.
Maximum Jitter
(Rx)
The maximum jitter of packets received during an H.323 call,
calculated from sample tests done once per minute.
6 - 8
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 - System Usage and Statistics
Call Detail Report Archives
Calls are added to the CDR until the file size reaches 50 KB, which is equivalent to
about 150 calls. The system then automatically archives the CDR and creates a new
CDR file. If an archive is already present, the new archive overwrites it.
Each CDR starts with Row 1, but the conference numbers continue from the file
most recently archived. Conference numbering restarts at 1 after the system
assigns conference number 100,000.
To get an archived CDR:
1. From your computer, open an FTP client.
2. FTP into the V500 system.
3. Enter this FTP command:
GET localcdr_archive.csv
4. Close your FTP session.
© Polycom, Inc.
6 - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
6 - 10
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Diagnostics and General
Troubleshooting
This chapter covers the diagnostic screens of the V500 system. It is organized by
category to help you troubleshoot any issue.
Diagnostic tools are available via the system itself and the system’s web server. To
connect to your system’s web server and troubleshoot via the web, enter your
system’s IP address in a web browser and browse to the required diagnostic tool.
What’s in this Chapter?
Page
© Polycom, Inc.
7 - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Sending a Message
You can send a message to the V500 system from the V500 web interface.
Only the near site can see the message; it is not broadcast to the far site in the call.
To send a message via the V500 web interface:
1. On a PC, open a web browser.
2. In the browser address line, enter the system’s IP address (for example,
http://255.255.255.255) to go to V500 web interface.
3. Enter your user name and the password, if a password has been established.
4. Go to System Setup > Diagnostics > Send a Message.
5. Enter a message (up to 100 characters in length), then click Send.
The message is displayed for 15 seconds on the screen of the system.
System Screens Quick Reference
These screens allow you to view information about the system, configure the
system, and diagnose performance issues if they arise. They are available on the
system and through the V500 web interface.
To view information about the system, go to the home screen and select System.
Then choose the type of information you need:
This choice:
Presents this information or capability:
Admin Settings
User interface customization, system customization, security,
dialing requirements and network configuration, Global
Management System information.
Diagnostics
System status and performance and system tests. The V500
web interface also offers the Send Message function and
provides access to the Call Detail Report.
System Information
Utilities
Identifying information.
Call scheduling and calendar.
System behavior and appearance.
User Settings
7 - 2
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 - Diagnostics and General Troubleshooting
Diagnostic Screens
You can view network statistics and perform diagnostic tests from the
V500 system’s Diagnostics screens.
To access the Diagnostics screens on the system:
>> Go to System > Diagnostics.
To access the Diagnostics screens from the V500 web interface:
1. On a PC, open a web browser.
2. In the browser address line, enter the system’s IP address (for example,
http://255.255.255.255) to go to V500 web interface.
3. Enter your user name and the password, if a password has been established.
4. Go to System Setup > Diagnostics and select one of the tools from the
Diagnostics menu.
The following diagnostic screem amd tools are available:
Call Status Tools
Diagnostic Tool
In the system’s user interface
In the V500 web interface
System Status screen
On the Diagnostics screen, select
Select Diagnostics > System
System Status.
Status.
Displays system status information,
including auto-answer point to point,
remote control battery, time server, Global
Directories, IP network, gatekeeper,
UPnP, and ISDN BRI line.
Call Summary screen
1. On the Diagnostics screen,
Select Diagnostics > System
select System Status.
Status > Call Summary.
Displays calling information, such as time
spent in calls, total number of IP and ISDN
calls, and percentage of time spent in IP
and ISDN calls.
2. Select
to go to the Call
Summary screen.
For more information about this screen, see Call Summary on
© Polycom, Inc.
7 - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Call Status Tools
Diagnostic Tool
Call Status screen
In the system’s user interface
In the V500 web interface
On the Diagnostics screen, select
1. Select Diagnostics > Call
Call Statistics.
Statistics.
Displays call type, data speed, and
number dialed for the current call.
2. Select
twice.
In ISDN calls, this screen also displays
connection status for each channel.
Selecting a channel call progress indicator
displays its ISDN number.
Call Statistics screen
1. On the Diagnostics screen,
Select Diagnostics > Call
select Call Statistics.
Statistics.
Displays call speed, audio and video
protocols, annexes, and error count for the
call in progress.
2. Select
to go to the Call
Statistics screen.
Call Detail Report screen
Not available.
Select Utilities > Call Detail
Report.
Displays the current Call Detail Report
(CDR) and provides access to the
archived CDR.
For more information about this screen, see Call Detail Report on
Network Tools
Diagnostic Tool
Near End Loop test
In the system’s user interface
In the V500 web interface
1. On the Diagnostics screen,
1. Select Diagnostics > Network
select Network.
> Near End Loop.
Tests whether your system is able to make
IP calls successfully.
2. Select Near End Loop to start 2. Click the Near End Loop icon.
the test.
3. Click Near End Loop again to
Monitor 1 displays the video and plays the
audio that would be sent to the far site in a
call.
3. Press any button on the remote
end the test.
control to stop the test.
This test is not available when you are in
an IP call.
PING test
1. On the Diagnostics screen,
1. Select Diagnostics > Network
select Network > PING.
> PING..
Tests whether the system can establish
contact with a far-site IP address that you
specify.
2. Enter the IP address that you 2. Enter the IP address that you
wish to test.
wish to test.
3. Select Start.
3. Click the PING icon.
If the test is successful, the
system displays a message
indicating that the IP address
under test is available.
If the test is successful, the
system displays a message
indicating that the IP address
under test is available.
7 - 4
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 - Diagnostics and General Troubleshooting
Network Tools
Diagnostic Tool
Trace Route test
In the system’s user interface
In the V500 web interface
1. On the Diagnostics screen,
1. On the Diagnostics menu,
select Network > Trace Route.
select Network > Trace Route.
Tests the routing path between the local
system and the IP address entered.
2. Enter the IP address that you 2. Enter the IP address that you
wish to trace.
wish to trace.
3. Select Start.
3. Click the Trace Route icon.
Error Log files
Not available.
Select Diagnostics > Network >
Error Log.
Video and Audio Tools
Diagnostic Tool
In the system’s user interface
In the V500 web interface
Color Bar test
1. On the Diagnostics screen,
1. Select Diagnostics > Video.
select Video.
2. Click the Color Bars icon.
Tests the color settings of your monitor for
optimum picture quality.
2. Select the Color Bars icon.
3. Click the Color Bars icon
3. Press any button on the remote
again to stop the test.
If the color bars generated during the test
are not clear, or the colors do not look
correct, the monitor needs to be adjusted.
control to stop the test.
Speaker test
1. On the Diagnostics screen,
1. Select Diagnostics > Audio >
select Audio > Speaker Test.
Speaker Test.
Tests the audio cable connections. A
400 Hz audio tone indicates that the local
audio connections are correct.
2. Select the Speaker Test icon. 2. Click the Speaker Test icon.
3. Press any button on the remote 3. Click the Speaker Test icon
control to stop the test.
again to stop the test.
If you are in a call, the far site will
also hear the tone.
The people at the site you are
testing will hear the tone, but you
will not. You can send a message
to tell them how to notify you
when they hear the speaker test.
Audio Meter screen
1. On the Diagnostics screen,
Select Diagnostics > Audio >
select Audio > Audio Meter.
Audio Meter to start the test.
Measures the strength of audio signals
from the system’s microphone.
The audio meter should
register between 0 and 15 dB.
The audio meter should register
between 0 and 15 dB.
If the system is not receiving sound,
ensure that people are close enough to
the system, and check whether the
microphone is muted.
2. To check the microphone,
stand near the system and
begin speaking.
© Polycom, Inc.
7 - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Reset and Restart
Diagnostic Tool
Reset System
In the system’s user interface
In the V500 web interface
1. On the Diagnostics screen,
Not available.
select Reset System.
•
•
Cycles power to the system.
2. Enter the system’s serial
Allows you to keep your system settings
(such as system name and network
configuration) or restore factory
settings.
number.
3. If you wish to restore the
original factory settings, select
Delete System Settings.
•
Allows you to keep or delete the
directory stored on the system.
This deletes the
administrator’s password,
CDR, and CDR archive along
with the other system settings.
You may wish to download the
CDR and CDR archive before
you delete system settings,
the setup wizard will lead you
through the initial
configuration after the system
restarts.
4. If you wish to remove the
directory, select Delete
Directory Entries.
This only deletes the system’s
local directory. System reset
does not affect the Global
Directory.
5. Select Reset System.
Restart System
Use the power switch on the
system.
1. Select Diagnostics > Reset
System.
Cycles power to the system.
2. Click the Reset System icon.
7 - 6
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 - Diagnostics and General Troubleshooting
Indicators
The V500 system uses indicator lights to provide status information. The following
tables give the meanings of each indicator.
System Lights
The system lights are located on the front of the V500 system.
When the V500 system...
Indicators are off
It means...
No power to the system.
The system is sleeping.
Green indicator blinks slowly
Green indicator flashes when you
use the remote control
The system is not in a call, and is receiving
signals from the remote control.
Amber indicator flashes when you
use the remote control
The system is in a call, and is receiving signals
from the remote control.
Green indicator is on
Amber indicator is on
Red indicator is on.
The system is ready to make a call.
The system is in a call.
The system microphone is muted.
Network Interface Lights
The BRI network interface lights are located on the back of the system near the BRI
connector.
When the BRI network interface... It means...
Indicators are off
•
•
•
No power to the system, or
The system is not connected to the network, or
The system is not receiving a clock signal from
the network, or
•
The system is restarting.
Green indicator is on
The system is receiving a clock signal from the
network.
Yellow indicator is on
The system is able to make a call.
Green and yellow indicators are on
•
•
The system is receiving a software update, or
The system is operating normally.
© Polycom, Inc.
7 - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
General Troubleshooting
This section presents problems, likely causes, and corrective actions. Problems are
presented as follows:
❑ Critical problems – Prevent use of the system or access to common functions.
❑ Severe problems – Prevent you from making calls successfully.
❑ Moderate issues – Prevent or interfere with meaningful communication
during the call.
❑ Minor issues – Detract from the user experience.
Critical Problems
This section describes problems that prevent normal use of the system. They may
also mask other problems. For example, if the system is not able to make a call and
there are no batteries in the remote, you will need to install new batteries before
you are able to determine whether the system can make calls.
Symptom
Cause
Solution
System does not respond in
any way.
The power switch is in the OFF
position.
Turn on the power switch.
The power cord is not connected.
Make sure that the system’s power cord is
in place, and that it is connected to a
power outlet
The power outlet is not active.
Check the power outlet by unplugging the
system and plugging in a lamp, radio, or
other small appliance. If it does not
operate, connect the power cord to a
different outlet.
The power supply is not operating
properly.
Check the power outlet by unplugging the
system and plugging in a lamp, radio, or
other small appliance. If it operates, the
problem is in the system. Call Polycom
Technical Support and arrange to return
the system for service.
System starts in the
Software Update screen.
The system software is corrupted or
not loaded properly.
Load the system software from your PC.
For instructions on how to do this, refer to
page 3-19 or consult your network
equipment provider.
7 - 8
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 - Diagnostics and General Troubleshooting
Symptom
Cause
Solution
System does not respond to
the remote control.
No batteries in the remote control.
Install the batteries in the remote control.
The batteries are installed incorrectly in Insert the batteries in the correct +/-
the remote control.
position.
The room lights operate in the 38 Khz
range and interfere with the remote
control signals.
Turn off the lights in the room and try the
remote control again.
The infrared sensor is not receiving
signals from the remote control.
Make sure you are pointing the remote
control at the infrared sensor on the front
of the system.
Severe Problems
The problems in this section prevent you from making calls successfully. They may
also mask less serious problems. For example, if you cannot complete a call and
there is also an audio problem, you will need to correct the problem that prevents
calling before you can determine whether there is an audio problem
Symptom
Cause
Solution
IP: The System Information
screen shows “waiting” in
the IP Video Number field.
The LAN is not working.
Check the LAN connection.
Contact your network service provider.
The DHCP server is not available.
Contact your network service provider to
correct the problem with the server or to
assing a static IP address.
IP: Error message occurs
when placing an IP (H.323)
call.
The system is not connected to the
LAN.
Verify that the LAN cable is connected
properly.
The system’s LAN cable is not
operating properly.
Replace the system’s LAN cable.
The far site is not connected.
Use the PING test (System >
Diagnostics > Network > PING) to
determine whether the far site is
accessible to your system. If the test fails,
the far site system is unavailable.
The system is not configured correctly
for the network.
Check your IP configuration.
The IP Gateway/Gatekeeper is not
Contact your network service provider.
operating or is not configured correctly.
© Polycom, Inc.
7 - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Symptom
Cause
Solution
ISDN: Line Status icons do
not go away so video calls
cannot be made.
The system is not connected to an
ISDN.
Check the ISDN line connections.
The ISDN number is entered
incorrectly.
Check the ISDN numbers with your
service provider.
The system was not able to auto-detect Select the Clear icon on the Auto Detect
SPIDs, or the SPID numbers are
entered incorrectly.
SPIDs page, and then select the Start
icon to automatically detect the new
SPIDs. Make sure your ISDN numbers are
entered correctly.
NOTE: The AT&T point-to-point
protocol does not require SPIDs.
The BRI network is directly connected
to a U interface.
Install an NT-1 device between your
network interface and the ISDN
connection.
The system is connected to an NT-1
then to a PBX.
You do not need an NT-1device when
connecting to a PBX. Connect the system
directly to the PBX S/T connection.
The ISDN line is provisioned incorrectly Check that your ISDN line is provisioned
by the ISDN service provider.
for Voice/Data.
The V500 system is in an unknown
state.
Power off the system, wait five seconds,
and power on the system.
ISDN: When placing a call,
progress indicators do not
turn green.
The call does not connect properly.
Try the call again.
ISDN: Error message occurs An ISDN cause code is received from
Try the call again.
when placing an ISDN
(H.320) call.
the ISDN line.
For more information, please refer to
The line did not connect.
Be sure you are calling the correct
number. The number may need to include:
•
•
•
•
•
A digit for an outside line
A long distance access code
An international access code
A country code
An area code or city code
Check that all network cables are properly
connected.
Power off the system, wait five seconds,
and power on the system.
Ask the person at the far site to call your
system.
The ISDN switch type is not configured
correctly on the V500 system.
Check the ISDN configuration and verify
with your ISDN service provider that the
system is configured correctly.
7 - 10
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 - Diagnostics and General Troubleshooting
Symptom
Cause
Solution
Cannot dial remote system
in bonding 128 K calls. (The
call progress circles only
show blue or yellow.)
Switch protocol issue.
Start by calling the far site at 1x56, 1x64,
2x56, or 2x64K, as appropriate. This will
verify the primary number. If these calls
complete, try the 128 K call.
Being able to dial non-bonded but unable
to dial bonded to all locations is usually a
switch protocol issue. Verify your ISDN
provisioning with the telephone service
provider.
Cannot select 112 or 128
speeds for bonding calls
from the speed selection.
Speeds do not show when selecting
the speed icon.
Add line speeds on the Admin Settings >
Network > Call Quality > Dialing
Speeds screen.
Moderate Issues
The problems in this section interfere with or prevent meaningful communication
in a call.
Symptom
Cause
Solution
The monitor screen remains
blank when you pick up the
remote control.
The monitor’s power cord is not
plugged in.
Connect the monitor’s power cord and
then power on the monitor.
The monitor is powered off.
Power on the monitor.
The monitor is not connected
correctly to the system.
Verify that the monitor is connected
correctly according to the installation
procedures in Connecting the Monitor on
The people at the far site
cannot see you.
The privacy shutter is closed
Open the privacy shutter.
© Polycom, Inc.
7 - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Symptom
Cause
Solution
No audio in a call.
The far site is muted.
Look for the far site Mute icon. Ask the far
site to unmute the microphone.
Note: The far site’s microphone may be
muted even if you do not see a far site
Mute icon.
The volume may be turned all the
way down.
Use the remote control to turn up the
volume.
The far site’s microphones are not
placed correctly. (Far-site systems
with separate microphones only.)
Ensure that each person who speaks is
facing a microphone and is close enough
to it.
The far site’s microphone is not
connected or does not have power.
(Far-site systems with separate
microphones only.)
Ask the far site to check the cable to the
microphone.
Too many line errors
Try the call again later.
No audio in a call.
The volume is turned all the way
down on the monitor or external
audio system.
Check the monitor’s or external audio
system’s volume setting. Then check the
system’s audio output using the Speaker
Test screen under Diagnostics > Audio.
You should hear a 400 Hz tone.
The monitor’s audio inputs are not
connected properly
Check audio output using the Speaker
Test screen under Diagnostics > Audio.
You should hear a 400 Hz tone.
Ask someone at the far site to speak into
the microphone, and check the Far Site
Audio meter on the Audio Meter screen
under Diagnostics > Audio to determine
whether your system is receiving audio.
The system’s audio outputs are not
connected properly.
Check the system’s audio connections to
the monitor.
Verify that the system is connected to the
correct audio connectors on the monitor.
7 - 12
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 - Diagnostics and General Troubleshooting
Symptom
Cause
Solution
The people at the far site
cannot hear you.
The people at your site are too far
from the system’s microphone.
Move closer to the system.
Your system’s microphone is muted. Check your system for one or more of
these mute indications:
•
•
Near site mute icon on the screen
System indicator is red
To unmute the system, press the
Mute button on the remote control.
System’s microphone does not work Contact your Polycom reseller.
The headphones do not
operate properly.
The headphone cable connector is
not fully seated.
Connect the headphone cable, making
sure it is fully seated.
Minor Issues
The issues in this table do not prevent meaningful communication, but detract
from the videoconference experience.
Symptom
Cause
Solution
Picture is blank on the main
monitor.
The system goes to “sleep” after a
period of inactivity.
Pick up the remote control to wake up the
system.
Picture freezes frequently
during an IP call.
There is too much traffic on the LAN.
Check the error count on the Call
Statistics screen.
Go to Admin Settings > Network > IP
Network > Quality of Service and enable
dynamic bandwidth.
Picture freezes frequently
during an ISDN call.
Too many network line transmission
errors. Check the error count on the
Diagnostics > Call Statistics screen
to verify this.
Try the call again.
Network interface cable may be bad.
Replace the cable.
Picture is slow or jerky.
Only one 64 Kbps channel is
connecting in your call.
Check the ISDN number of the far site.
Ask the far site to call your site.
The system is receiving video that
includes a large amount of motion.
A background with less motion provides a
better, smoother video picture.
Too many network line transmission
errors. Check the error count on the
Diagnostics > Call Statistics screen
to verify this.
Try the call again.
No picture in the PIP window The lens cover is closed.
Open the lens cover.
© Polycom, Inc.
7 - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Symptom
Cause
Solution
Not enough volume during a
call.
The volume is set too low on the
system.
Turn up the volume using the remote
control.
The volume is set too low on the
monitor.
Turn up the volume on your monitor.
The people at the far site are too far
from the microphone.
Ask the people at the far site to move
closer to the microphone.
Sound effects too loud or too
soft.
The sound effects volume is not set at
desired level.
Adjust the sound effects volume on the
Audio Settings screen. If you do not want
to hear sound effects, set the volume to 0.
You hear the incoming call
ring when you have set
sound effects volume to 0.
The internal ringer is enabled.
On the Audio Settings screen, clear the
Enable Internal Ringer option.
Incoming call ring is too loud
or too soft.
The sound effects volume is not set at
desired level.
Adjust the sound effects volume on the
Audio Settings screen. If you do not want
to hear sound effects, set the volume to 0.
You can hear yourself on
your system’s monitor.
The far site microphone is too close to
the system’s audio speaker. (Far-site
systems with separate microphones
only.)
At the far site, make sure the microphone
is placed away from the system’s audio
speaker.
The far site audio volume may be too
loud.
Turn down the audio volume at the far site.
Enter the password.
Cannot enter the Admin
Settings screen.
The system requires a password.
Low battery icon on the
screen.
Low batteries in the remote control.
Replace the batteries in the remote
control with 3 AAA batteries.
7 - 14
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 - Diagnostics and General Troubleshooting
Symptom
Cause
Solution
Cannot access the system
from the V500 web interface.
Web access is not enabled.
Go to Admin Settings > General
Settings > Security and enable web
access.
DHCP Client is ON and no DHCP
Contact your network service provider.
server is available.
The LAN cable is not connected.
Connect the LAN cable to the LAN port on
the rear of the system.
Check the LAN cable to your computer.
Bad LAN cable.
Check the lights on the system. There
should be a steady green light indicating a
connection to the LAN, and a flashing
orange light indicating LAN traffic.
DHCP Client is ON and no DHCP
Contact your network service provider.
server is available.
There is a firewall between your PC
and your system.
Consult your network service provider.
Your PC is on a different subnet and
there is a router between you and your
system.
Place the PC and the V500 system on the
same subnet. If this corrects the problem,
check your router configuration. If it does
not, contact your network service provider.
System does not allow
management via the V500
web interface.
Wrong password.
Enter the correct user name and
password.
NOTE: The default user name is admin,
and the default password is the unit’s
serial number.
Too many managers are logged into
the system.
Only five system managers are allowed at
any one time. To log everyone out, restart
your system.
The monitor displays an
error icon during an ISDN
call.
The system has received more than
the acceptable number of CRC errors
or FEC errors within one second.
Retry the call if the video or audio quality
becomes unacceptable to the call
participants.
The monitor displays an
error icon during an IP call.
The system has detected packet loss
above the acceptable level set for the
system.
Retry the call if the video or audio quality
becomes unacceptable to the call
participants.
© Polycom, Inc.
7 - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Normal System Behaviors
Symptom
Cause
Solution
Screen is blank; start music
plays and the logo appears
briefly. The light on the front
of the V500 system blinks.
The system is starting.
This is normal.
The monitor goes blank after The system is sleeping.
displaying the splash
screen.
System is in power save sleep mode. The
system wakes up on any action from the
remote control or on an incoming call.
7 - 16
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 - Diagnostics and General Troubleshooting
How to Contact Technical Support
If you are not able to make test calls successfully and you have verified that the
equipment is installed and set up correctly, contact Polycom Technical Support by
telephone or Internet as described below.
By Telephone
Before calling Polycom Technical Support, please have the following information
ready. We also suggest that you go to System > System Information so that you
will have the System Information screen showing when you call for help.
❑ Description of the issue – What is happening or not happening, and any
related events you may be able to notice.
❑ The 14-digit serial number on the bottom of the system.
Contact Polycom Technical Support at 1-800-POLYCOM.
By Internet
Enter the following information, then ask a question or describe the problem. This
information helps us to respond faster to your issue:
❑ The 14-digit serial number in the System Information screen (also present on
the bottom of the system)
❑ The software version (go to System > System Information)
❑ Information about your network
❑ Troubleshooting steps you have already tried
© Polycom, Inc.
7 - 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
7 - 18
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
This appendix provides the following technical details about the V500 system:
❑ Cable Descriptions
❑ Cable Drawings
❑ Q.850 Cause Codes
Cable Descriptions
The following table gives information about the cables shipped with the system.
Drawings for these cables are included in this appendix.
Maximum Approved
Cable
Length
Part Number Shipped
LAN cable
100 ft (30 m)
2457-08343-001
12 ft (3.6 m)
Orange RJ-45
Composite video cable
Triple RCA with S-video
2457-08674-001
6 ft (1.8m)
If you have the ISDN option, you can also attach a BRI cable. The part number for
this cable is 2457-08717-001 and the length is 20 ft.
© Polycom, Inc.
Appendix - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Cable Drawings
The following cables are provided with V500 systems:
❑ LAN cable
❑ Composite video cable
Their pin-outs are shown in the following drawings.
LAN Cable
3
3.35"
MOLDED STRAIN RELIE
BOTH ENDS.
1
WIRING COLOR CODE STANDARDS: (WIRE/STRIPE)
CONN. RJ-45
( x2 )
PIN 8
P1
P2
PIN 8
PIN PIN
AT&T
#
1
2
3
4
5
6
7
8
#
1
2
3
4
5
6
7
8
258A/268B
P1
P2
WHITE/ORANGE
ORANGE/WHITE
WHITE/GREEN
BLUE/WHITE
CABLE, 8 COND, 24 AWG,
BLACK PVC JACKET
CATEGORY 5, TWISTED PAIR
WHITE/BLUE
MINIMUN OF 2 TWISTS PER INCH.
GREEN/WHITE
WHITE/BROWN
BROWN/WHITE
12 FEET +/- 3"
NOTES: (UNLESS OTHERWISE SPECIFIED).
1
MOLDING MATERIAL: PVC UL94 V-0
COLOR: ORANGE, APPROXIMATE MATCH TO
PANTONE #1665 U.
2. APPROVED VENDOR: PAN INTERNATIONAL ELECTRONICS
(THAILAND) CO, LTD. (66-2) 5293549-50.
PAN INTERNATIONAL DETAILED SPEC IS IN THE PART FILE.
3
THE BARCODE CONTAINS LAST 8 DIGIT OF CABLE PART
NUMBER (REMOVE VV2457).
LABLE SPEC : LASER LABLE
SIZE : LABLE SIZE (12 X 76mm)
LAN Cable 2457-08343-001
Appendix - 2
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Q.850 Cause Codes
The following table describes codes that the ISDN switch sends to the V500 system
to indicate call status. Although the codes are standardized, each ISDN service
provider defines them differently. Because of this, the definitions in the table may
not exactly match the messages that you see.
Code Cause
Definition
1
Unassigned number
The switch received the sent ISDN number in the
correct format, but no destination equipment uses the
number.
2
3
6
7
No route to specified
transit network
The ISDN exchange does not recognize the
intermediate network through which to route the call.
No route to
destination
The intermediate network through which the call is
routed does not serve the destination address.
Channel
unacceptable
The specified channel does not provide adequate
service quality to accept the requested connection.
Call awarded and
delivered
The user is assigned an incoming call that is being
connected to a call channel that has already been
established for this user and this type of call.
16
17
Normal call clearing
User busy
The originator or receiver of the call has requested that
it be cleared.
All B channels are in use; the called system
acknowledges the connection request, but is unable to
accept the call.
18
19
No user responding
The destination equipment does not respond to the call,
so the connection cannot be completed.
No answer from user
(user alerted)
The destination equipment did not complete the
connection within the prescribed time after responding
to the connection request. The problem is at the remote
end of the connection.
21
22
Call rejected
The destination equipment is capable of accepting the
call, but has rejected it for an unknown reason.
Number changed
The ISDN number used to set up the call is no longer
valid. (The diagnostic field of the message may return
an alternate address assigned to the called equipment.)
26
27
Non-selected user
clearing
The destination is capable of accepting the call, but did
not assign it to the user.
Destination out of
order
A signaling message cannot be delivered because the
interface is not functioning correctly, and the destination
cannot be reached. This condition might be temporary;
for example, remote equipment might be turned off.
Appendix - 4
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Code Cause
Definition
28
Invalid number
format
Destination address was incomplete or presented in an
unrecognizable format, which prevented the connection
from being established.
29
30
31
34
38
Facility rejected
The network cannot provide the facility requested by the
user.
Response to
STATUS INQUIRY
The equipment returns this message when it receives a
STATUS INQUIRY message.
Normal, unspecified
A normal event has occurred with no standard cause
applying. No resulting action is required.
No circuit/channel
available
The call cannot be taken because no appropriate
channel is available to establish the connection.
Network out of order A network problem prevented the call from reaching its
destination. Attempts to reconnect will probably fail until
the network problem is corrected.
41
42
43
Temporary failure
A network error occurred. The problem will be resolved
shortly. Attempts to reconnect may succeed.
Switchingequipment The destination cannot be reached because the
congestion
network switching equipment is temporarily overloaded.
Access information
discarded
The requested access information cannot be provided
by the network. The diagnostic message may explain
the problem.
44
47
49
50
57
58
63
Requested
circuit/channel not
available
The remote equipment cannot provide the requested
channel. This may be temporary.
Resource
unavailable,
unspecified
An unknown problem prevents the remote equipment
from providing the requested resource.
Quality of service
unavailable
The network cannot provide the requested quality of
service (as defined by CCITT recommendation X.213).
This may be a subscription problem.
Requested facility
not subscribed
The remote equipment is capable of providing the
requested supplementary service, but is not subscribed
to it.
Bearer capability not
authorized
The caller has requested a bearer capability that the
network can provide, but the user is not authorized to
use. This may be a subscription problem.
Bearer capability not
presently available
The network normally provides the requested bearer
capability, but cannot provide it now. This may be a
temporary network problem or a subscription problem.
Service or option not
available,
unspecified
An unspecified problem prevents the network or remote
equipment from providing the requested service or
option. This might be a subscription problem.
© Polycom, Inc.
Appendix - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Code Cause
Definition
65
66
69
70
Bearer capability not
implemented
The network is not capable of providing the bearer
capability requested by the user.
Channel type not
implemented
The requested channel type is not supported by the
equipment sending this code.
Requested facility
not implemented
The remote equipment is not capable of providing the
requested supplementary service.
Onlyrestricteddigital The network is unable to provide unrestricted digital
information bearer is
available
information over bearer capability.
79
81
Service or option not
available,
unspecified
The network or remote equipment is unable to provided
the requested service option for an unspecified reason.
This might be a subscription problem.
Invalid call reference
value
The remote equipment received a call with a call
reference that is not currently in use on the
user-network interface.
82
83
Identified channel
does not exist
The receiving equipment is requested to use a channel
that is not activated on the interface for calls.
A suspended call
exists but this call
identity does not
The network received a call resume request that
contained a call identity information element that does
not match any suspended call.
84
85
Call identity in use
The network received a call suspend request that
contained a call identity information element for a call
that is already suspended.
No call suspended
The network received a call resume request when there
was not a suspended call pending. This might be a
transient error that will be resolved by successive call
retries.
86
Call having
The network received a call resume request containing
a call identity information element for a call that was
cleared while suspended, either by timeout or by the
remote user.
requested call
identity has been
cleared
88
91
95
Incompatible
destination
Indicates that an attempt was made to connect to
non-ISDN equipment, such as an analog line.
Invalid transit
network specified
The ISDN exchange was asked to route the call through
an unrecognized intermediate network.
Invalid message,
unspecified
An invalid message was received, for an unknown
reason. This is usually due to a D-channel error. If this
error occurs systematically, report it to your ISDN
service provider.
96
Mandatory
information element
is missing
The equipment received a message that did not include
one of the mandatory information elements. This is
usually due to a D-channel error. If this error occurs
systematically, report it to your ISDN service provider.
Appendix - 6
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Code Cause
Definition
97
Message type
nonexistent or not
implemented
The equipment received a message of a type that is
invalid or not supported. This code indicates either a
problem with the remote configuration or a problem with
the local D channel.
98
Message
The equipment received a message that is not valid in
the current call state. Cause 98 is usually due to a
D-channel error. If this error occurs systematically,
report it to your ISDN service provider.
incompatible with
call state or
message type
nonexistent
99
Information element
nonexistent or not
implemented
The equipment received a message that includes
information elements which were not recognized. This is
usually due to a D-channel error. If this error occurs
systematically, report it to your ISDN service provider.
100
101
Invalid information
element contents
The equipment received a message that includes
invalid information in the information element. This is
usually due to a D-channel error.
Message not
compatible with call
state
The remote equipment received a message that does
not correspond to the current state of the connection.
This is usually due to a D-channel error.
102
111
127
Recovery on timer
expiry
A time-out has triggered an error-handling (recovery)
procedure. This problem is typically temporary.
Protocol error,
unspecified
An unspecified D-channel error when no other standard
cause applies.
Interworking,
unspecified
An event occurred within a network that does not
provide causes for the action that it takes. The precise
problem is unknown.
145
146
ISDN layer 1 and/or
2 link not established network connections.
User needs to check cabling, ISDN adapter status and
ISDN layer 3
There is either a switch protocol error, or (in the United
connection to the
ISDNswitch/network
inactive
States or Canada) a SPID assignment problem.
255
ISDN command
processing error
The ISDN signaling code has encountered an error
processing an ISDN action. ISDN adapter busy-wait
and retry.
© Polycom, Inc.
Appendix - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Appendix - 8
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Legal Notices
Important Safeguards
Read and understand the following instructions before using the system:
•
Close supervision is necessary when the system is used by or near children. Do not leave unattended while in
use.
•
•
•
•
•
Only use electrical extension cords with a current rating at least equal to that of the system.
Always disconnect the system from power before cleaning and servicing and when not in use.
Do not spray liquids directly onto the system when cleaning. Always apply the liquid first to a static free cloth.
Do not immerse the system in any liquid or place any liquids on it.
Do not disassemble this system. To reduce the risk of shock and to maintain the warranty on the system, a
qualified technician must perform service or repair work.
•
•
•
•
Connect this appliance to a grounded outlet.
Only connect the system to surge protected power outlets.
Keep ventilation openings free of any obstructions.
SAVE THESE INSTRUCTIONS.
License Restrictions
THE SOFTWARE PROGRAMS CONTAINED OR DESCRIBED HEREIN ARE CONFIDENTIAL INFORMATION
AND PROPRIETARY PRODUCTS OF POLYCOM, INC. OR ITS LICENSORS.
Buyer shall not sublicense or otherwise distribute any of the Subject Programs except to End Users and/or
resellers who have entered into a Sublicense Agreement. For purposes of this Agreement a “Sublicense
Agreement” shall mean a written license agreement between the Buyer and its purchaser, or, in the case of any
sale by Buyer to a reseller, between such reseller and the End User, that is either 1) signed by the End User or 2)
included with the Documentation, in such a manner that the End User reasonably indicates its acceptance of the
Sublicense Agreement by turning on and using the Computer Equipment. Polycom, Inc. shall include so-called
“break the seal software licenses” with the Documentation, and Buyer shall not remove or alter any such
Sublicense Agreements or any notifications or warning stickers relating thereto. Buyer shall not waive, amend, or
otherwise modify any Sublicense Agreement without Polycom’s prior consent.
Title to all Subject Programs shall at all times remain and vest solely with Polycom, Inc. and its licensors. Buyer
acknowledges Polycom’s claim that the Subject Programs are its trade secret and confidential property, and shall
treat them as such. Buyer will not attempt to disassemble, decompile, reverse-engineer or otherwise endeavor to
discover or disclose the methods and concepts embodied in the Subject Programs. Except as expressly allowed
under this Agreement, the Buyer shall not copy, modify, transcribe, store, translate, sell, lease, or otherwise
transfer or distribute any of the Subject Programs in whole or in part, without prior authorization, in writing, from
Polycom, Inc. Buyer shall not remove or destroy any copyright, patent, trademark or other proprietary mark or
notice on Computer Equipment, and shall reproduce any such marks on any copies of Subject Programs that it
makes hereunder.
You shall not, and shall not allow, any third party to 1) decompile, disassemble, or otherwise reverse-engineer or
attempt to reconstruct or discover any source code or underlying ideas or algorithms of the software by any means
whatsoever or 2) remove any product.
Warranty
Polycom, Inc. warrants its products to be free of defects in materials and factory workmanship for a period of twelve
(12) months from date of purchase. This warranty does not apply to damage to products resulting from accident,
misuse, service or modification by anyone other than a Polycom, Inc. authorized service facility/dealer. The
warranty is limited to the original purchaser and is not transferable. Any liability of Polycom, Inc. or its suppliers
with respect to the product or the performance thereof under any warranty, negligence, strict liability or other theory
will be limited exclusively to product repair or replacement as provided above. Except for the foregoing, the product
is provided “as is” without warranty of any kind including without limitation, any warranty of merchantability or
fitness for a particular purpose. The entire risk of the quality and performance of the software programs contained
in the system is with you.
© Polycom, Inc.
Safety and Legal Notices - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Limitation of Remedies and Damages
Polycom, Inc., its agents, employees, suppliers, dealers and other authorized representatives shall not be
responsible or liable with respect to the product or any other subject matter related thereto under any contract,
negligence, strict liability or other theory for any indirect, incidental, or consequential damages, including, but not
limited to loss of information, business, or profits.
The law of certain states or nations does not permit limitation or exclusion of implied warranties and consequential
damages, so the above limitations, disclaimers, or exclusion may not apply to you. This warranty gives you special
legal rights. You may also have other rights that vary by state and nation.
Warning
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the
user may be required to take adequate measures.
USA and Canadian Regulatory Notices
FCC Notice
Class A Digital Device or Peripheral
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
In accordance with Part 15 of the FCC rules, the user is cautioned that any changes or modifications not expressly
approved by Polycom Inc. could void the user's authority to operate this equipment.
The socket outlet to which this apparatus is connected must be installed near the equipment and must always be
readily accessible.
Part 15 FCC Rules
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) this device must accept any interference received, including interference that may cause undesired operation.
Part 68 FCC Rules
This equipment complies with part 68 of the FCC rules and the rules adopted by the ACTA. On this equipment is
a label that contains, among other information, a product identifier in the format US:AAAEQ#TXXX system. If
requested, this number must be provided to the telephone company.
This equipment may not be used on a coin service or party line.
If you experience trouble with your V500 System, disconnect it from the telephone line to determine if the
registered equipment is malfunctioning. For repair or warranty information, please contact Polycom Inc. at
1-888-248-4143 or 4750 Willow Road, Pleasanton, CA 94588-2708, USA. Contact information may also be found
at http://www.polycom.com. If the system is causing harm to the network, the telephone company may request
that you disconnect it until the problem is corrected.
If your V500 System causes harm to the telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. However, if advance notice is not practical, you will be
notified as soon as possible. You will be advised of your right to file a complaint with the FCC if you believe it is
necessary.
Your telephone company may make changes in its facilities, equipment, operations, or procedures that could
affect the operation of your equipment. If they do, you will be given advance notice so that you may make any
changes necessary to maintain uninterrupted service.
The REN is useful to determine the quantity of devices that may be connected to the telephone line. Excessive
RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not
all areas, the sum of RENs of all devices that may be connected to a line, is determined by the total RENs, contact
the local telephone company.
Safety and Legal Notices - 2
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Legal Notices
FCC compliant telephone cords and modular plugs are provided with this equipment. This equipment is designed
to be connected to the telephone network or premises’ wiring using a compatible modular jack, which is Part 68
compliant. See installation instructions for details.
WHEN PROGRAMMING EMERGENCY NUMBERS AND/OR MAKING TEST CALLS TO EMERGENCY
NUMBERS:
1) Remain on the line and briefly explain to the dispatcher the reason for the call.
2) Perform such activities in the off-peak hours, such as early morning or late evening.
Industry Canada (IC)
This Class [A] digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la Classe [A] est conforme à la norme NMB-003 du Canada.
The Industry Canada label identifies certified equipment. This certification means that the equipment meets
telecommunications network protective, operational and safety requirements as prescribed in the appropriate
Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment
will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the
local telecommunications company. The equipment must also be installed using an acceptable method of
connection. The customer should be aware that compliance with the above conditions may not prevent
degradation of service in some situations. Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone
lines and internal metallic water pipe system, if present, are connected together. This precaution may be
particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate
electric inspection authority, or electrician, as appropriate.
The Ringer Equivalence Number (REN) assigned to each relevant terminal device provides an indication of the
maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface
may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the
devices does not exceed 5.
The REN of this equipment is either marked on the unit or included in the new style USA FCC registration number.
In the case that the REN is included in the FCC number, the user should use the following key to determine the
value:
•
•
The FCC number is formatted as US:AAAEQ#TXXX.
# is the Ringer Equivalence Number without a decimal point (e.g. REN of 1.0 will be shown as 10, REN of 0.3
will be shown as 03). In the case of a Z ringer, ZZ shall appear. In the case of approved equipment without a
network interface or equipment not to be connected to circuits with analog ringing supplied, NA shall appear.
EEA Regulatory Notices
CE Mark R & TTE Directive
This V500 System has been marked with the CE mark. This mark indicates compliance with EEC Directives
89/336/EEC, 73/23/EEC 1999/5/EC. A full copy of the Declaration of Conformity can be obtained from Polycom
Ltd., 270 Bath Road, Slough UK SL1 4DX.
Declaration of Conformity:
Hereby, Polycom Ltd. declares that this V500 System is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Konformitetserklæring:
Hermed erklærer Polycom Ltd., at indestående V500 System er i overensstemmelse med de grundlæggende krav
og de relevante punkter i direktiv 1999/5/EF.
© Polycom, Inc.
Safety and Legal Notices - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Konformitätserklärung:
Hiermit erklärt Polycom Ltd., dass der V500 System die grundlegenden Anforderungen und sonstige maßgebliche
Bestimmungen der Richtlinie 1999/5/EG erfüllt.
Vaatimustenmukaisuusvakuutus:
Polycom Ltd. vakuuttaa täten, että V500 System on direktiivin 1999/5/EC keskeisten vaatimusten ja sen muiden
tätä koskevien säännösten mukainen.
Déclaration de conformité:
Par la présente, Polycom Ltd. déclare que ce V500 System est conforme aux conditions essentielles et à toute
autre modalité pertinente de la Directive 1999/5/CE.
Dichiarazione di conformità:
Con la presente Polycom Ltd. dichiara che il V500 System soddisfa i requisiti essenziali e le altre disposizioni
pertinenti della direttiva 1999/5/CE.
Verklaring van overeenstemming:
Hierbij verklaart Polycom Ltd. dat diens V500 System voldoet aan de basisvereisten en andere relevante
voorwaarden van EG-richtlijn 1999/5/EG.
Declaração de Conformidade:
Através da presente, a Polycom Ltd. declara que este V500 System se encontra em conformidade com os
requisitos essenciais e outras disposições relevantes da Directiva 1999/5/CE.
Declaración de conformidad:
Por la presente declaración, Polycom Ltd. declara que este V500 System cumple los requisitos esenciales y otras
cláusulas importantes de la directiva 1999/5/CE.
Överensstämmelseförklaring:
Polycom Ltd. förklarar härmed att denna V500 System överensstämmer med de väsentliga kraven och övriga
relevanta stadganden i direktiv 1999/5/EG.
CE Mark LVD and EMC Directive
This V500 System has been marked with the CE mark. This mark indicates compliance with EEC Directives
89/336/EEC and 73/23/EEC. A full copy of the Declaration of Conformity can be obtained from Polycom Ltd., 270
Bath Road, Slough UK SL1 4DX, UK.
Mains Powered POTS Voice Telephony Without Emergency 000 Dialing
Warning: This equipment will be inoperable when mains power fails.
Safety and Legal Notices - 4
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Legal Notices
Underwriters Laboratories Statement
The system is intended to be powered only by the supplied power supply unit.
Special Safety Instructions
Follow existing safety instructions and observe all safeguards as directed.
Installation Instructions
Installation must be performed in accordance with all relevant national wiring rules.
Plug Acts as Disconnect Device
The socket outlet to which this apparatus is connected must be installed near the equipment and must always be
readily accessible.
© Polycom, Inc.
Safety and Legal Notices - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Safety and Legal Notices - 6
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
B
access levels
backlight compensation 4-6
bandwidth
administrators 4-2
advanced users 4-2
new users 4-2
account number 5-6
dynamic 3-10
bass adjustment 4-10
BRI network interface
configuring 3-13
address
gatekeeper 3-7
IP 3-4
connecting 2-6
administrator password
configuring 4-14
resetting 4-3
lights 7-7
brightness, of camera 4-6
browser requirements 3-3
screens that require 4-3
setting 4-2
setting with Setup Wizard 3-3
allowing
C
cable
descriptions Appendix-1
drawings Appendix-2
ISDN BRI 2-6
monitor 1-5
answering mode 4-13
area code, setting 4-15
audio
power 2-4
Audio Meter test 7-5
configuring 4-10
confirmation, keypad 4-12
diagnostic tools 7-5
protocol 6-3
quality 1-2
sound effects volume 4-10
volume 4-10
S-video 1-5
call
answering mode 4-13
Call Statistics screen 7-4
Call Status screen 7-4
choosing call preferences 3-14
number of 6-2
preferences 3-15
progress indicators 6-4
quality 4-18
volume on external system 4-10
Audio Meter screen 7-5
Audio Meter test 7-5
auto-answer
muting 4-10
point to point 4-11
auto-detecting
recent 6-5
speed, maximum 3-15
speed, optimizing 3-7
statistics 6-3
status 6-4
status tools 7-3
summary 6-2
ISDN connectivity 3-13
SPIDs 3-14
test 3-17
time, maximum 4-5
tracking 5-6
type 6-3
© Polycom, Inc.
Index - 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
Call Detail Report (CDR)
account numbers 5-6
archives 6-9
connector
BRI 2-6
composite video 2-3
LAN 2-4
features 1-4
information in 6-6
screen 7-4
power 2-4
S-video 2-3
cord, power
viewing and downloading 6-6
viewing recent calls 6-5
Call Statistics screen 7-4
Call Summary screen 7-3
camera
configuring settings 4-6
setting brightness 4-6
cause codes, Q.850 Appendix-4
closed captions
connecting 2-4
description 1-5
country code 4-15
country selection 4-15
customizing
Home screen 4-17
system behavior 4-5
system features 1-2
audio options 4-22
displaying 4-22
D
Telnet session connection 4-24
V500 web interface connection 4-23
Color Bar test 7-5
color schemes 4-21
composite video cable
description 1-5
data rate
date, displaying 4-18
daylight saving time 4-15
diagnostics
IP connectivity tools 7-4
network and call status tools 7-3
reset and restart 7-6
video and audio tools 7-5
dialing
drawing Appendix-3
configuring
audio 4-10
BRI 3-13
Dual Monitor Emulation 4-7
firewall 3-12
monitor 4-7
PIP 4-7
SNMP 5-8
last number dialed 4-19
options 4-18
prefix, ISDN 3-13
rules 3-17
speed dialing 4-19
connecting
DID number 3-8
Diffserv 3-10
directory
ISDN BRI network interface 2-6
LAN 2-3
monitor 2-3
optional equipment 2-6
power 2-4
standard equipment 2-2
system 2-2
allowing access 4-18
allowing changes 4-5
configuring settings 4-12
confirming additions 4-13
confirming deletions 4-13
features 1-3
connectivity checklist, for network 3-2
managing with V500 web interface 5-4
server 3-16
Index - 2
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
displaying
date and time 4-18
G
gatekeeper
graphics 4-7
configuring system to use 3-7
IP address 3-7
name 3-6
icons in a call 4-7
system name 4-18
registering 3-6
using 3-7
gateway
DNS name 3-4
DNS server 3-5
documentation
configuring system to use 3-8
placing call 3-6
specifying default 3-5
available resources 4-25
description 1-5
specifying number type 3-8
Global Directory Server 3-16
Global Directory, features 1-3
Global Management System™
description 5-5
management servers list 5-5
requesting support from administrator 5-7
See also remote management
global services, configuring 5-5
domain name 3-5
Dual Monitor Emulation
description 1-2
specifying 4-7
using 4-8
duplex mode 3-5
dynamic bandwidth 3-10
See also Quality of Service
E
E.164
H
alias 3-8
H.323
displaying extension 3-6
name 3-6
encryption
enabling AES 4-13
features 1-3
viewing type 6-3
specifying for Home screen 4-18
specifying name 3-7
specifying settings 3-6
hardware
setting up optional 2-6
setting up standard 2-2
help
error icon 7-15
extension
H.323 4-18
H.323, displaying 3-6
H.323, specifying 3-6
H.323, specifying for gatekeeper 3-7
H.323, specifying for gateway 3-8
external audio system, volume 4-10
from GMS administrator 5-6
Home screen
adding sites 4-19
configuring settings 4-18
designing 4-17
F
far site
features 1-2
system information 6-3
system name 4-12
firewall 3-12
host name 3-4
© Polycom, Inc.
Index - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
I
K
icons
keypad
displaying 4-7
error 7-15
indicators
audio confirmation 4-12
remote control 4-12
kiosk mode
call progress 6-4
network interface 7-7
system 7-7
description 4-5
installing
L
features 1-3
LAN
cable 1-5
optional equipment 2-6
standard equipment 2-2
system 2-1
cable, drawing Appendix-2
choosing speed 3-5
properties, configuring 3-4
See also IP
instructions, on-screen 4-20
internal ringer 4-10
IP
address, displaying 4-18
address, entering 3-4
address, gatekeeper 3-7
address, obtaining automatically 3-4
address, static 3-4
configuring network support 3-6
connectivity tools 7-4
dynamic address 3-4
precedence 3-10
language selection 4-15
last number dialed 4-19
lights
indicator 7-7
network interface 7-7
system 7-7
location settings
area code/city code 4-15
country 4-15
country code 4-15
daylight saving time 4-15
language 4-15
See also LAN
ISDN
configuring network interface 3-13
configuring support 3-13
connectivity, auto-detecting 3-13
dialing rules 3-17
time difference from GMT 4-15
M
management servers list 5-5
managing
installing BRI network interface 2-6
international access code 4-15
Q.850 cause codes Appendix-4
SPIDs 3-14
voice algorithm 3-13
system remotely 5-1
marquee text 4-20
master audio volume 4-10
meeting password 4-14
MIBs, downloading 5-8
monitor
J
cable 1-5
cable, drawing Appendix-3
configuring 4-7
connecting 2-3
My Contacts list 4-19
Index - 4
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
point to point
auto-answer calls 4-4
call answer mode 4-13
ports
N
name
DNS 3-4
far-site system 4-12
host 3-4
TCP 3-11
UDP 3-11
positioning, system 2-2
power
See also firewall
Near End Loop screen 7-4
Near End Loop test 7-4
network
connecting 2-4
resetting system 7-6
restarting system 7-6
supply, auto-sensing 1-3
supply, description 1-5
switch 2-5
configuring use of 3-1
connecting to ISDN 2-6
connecting to LAN 2-4
connectivity checklist 3-2
diagnostic tools 7-3
getting ready 3-2
preferences, call 3-14
preventing security issues 3-12
profile
interface lights 7-7
network interface
managing 5-3
storing 5-3
uploading 5-3
lights 7-7
protocol
NT-1 device 2-6
audio 6-3
video 6-3
O
on-screen instructions 4-20
optional equipment
Q
BRI network interface 2-6
headphone 2-6
Q.850 cause codes Appendix-4
quality
outbound call route 3-7
audio 1-2
call 4-18
Quality of Service 3-10
P
packet loss 6-3
R
password
administrator, forgetting 3-3
Global Directory 3-16
meeting 4-14
recent calls
list 6-5
See also Call Detail Report (CDR)
registration, gatekeeper 3-6
remote access, allowing 4-14
setting 4-14
PBX 2-6
PING screen 7-4
PING test 7-4
PIP, configuring 4-7
© Polycom, Inc.
Index - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
remote control
Softupdate 3-19
configuring 4-12
description 1-5
features 1-2
software, upgrading 3-19
sound effects volume 4-10
Speaker test 7-5
installing batteries 2-5
keypad configuration 4-12
troubleshooting 7-9
remote management
tools 5-1
using web browser 5-2
requirements, web browser 3-3
reset system 7-6
Reset System screen 7-6
restart system 7-6
ringer, internal 4-10
Speaker Test screen 7-5
speed dial 4-19
SPIDs 3-14
standard equipment
LAN 2-3
monitor 2-3
power 2-4
remote control 2-5
statistics
call 6-3
Call Statistics screen 7-4
system 6-1
S
status
Call Status screen 7-4
network and call diagnostic tools 7-3
system 3-18
screen
diagnostic 7-3
diagram of system 4-3
system quick reference 7-2
security 3-12
System Status screen 7-3
subnet mask 3-5
switch, power 2-5
features 1-3
setting options 4-14
serial number 7-17
servers
system
checking status 3-18
configuring call settings 4-11
designing behavior 4-11
displaying name 4-18
introduction to 1-1
lights 7-7
directory 3-16
DNS 3-5
WINS 3-5
optional components 1-6
positioning 2-2
setup wizard
running 3-3
using 3-3
screens quick reference 7-2
setting up hardware 2-1
specifying name 4-12
standard components 1-5
system profiles, managing 5-3
System Status screen 7-3
SIP
enabling 3-15
specifying settings 3-9
Siren™ 14, description 1-2
site buttons, adding 4-19
sleep mode 7-16
snapshots, timeout 4-7
SNMP
configuring for SNMP management 5-9
setting up 5-8
Index - 6
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
user limitations
allow directory changes 4-12
T
technical support
contacting 7-17
managing user access 4-2
maximum call speed 3-15
maximum call time 4-11
removing features 4-18
setting 4-5
information to provide 7-17
telephone number 7-17
web page address 7-17
test
user settings
allow video display on web 4-4
auto-answer point to point 4-4
backlight compensation 4-4
Dual Monitor Emulation 4-4
far-site name display time 4-4
keypad audio confirmation 4-4
managing access 4-2
Audio Meter 7-5
Color Bar 7-5
Near End Loop 7-4
PING 7-4
Speaker 7-5
test calls 3-17
time
meeting password 4-4
mute auto-answer calls 4-4
PIP adjustment 4-4
daylight saving 4-15
difference from GMT 4-15
displaying 4-18
screen saver 4-21
server 4-15
V
setting 4-15
V500
description 1-5
specifying maximum during call 4-11
tones
headphone, connecting 2-6
illustration 1-1
introduction to 1-1
ISDN BRI network interface 2-6
key features 1-2
internal ringer 4-10
tools
IP connectivity 7-4
network and call status 7-3
reset and restart 7-6
video and audio 7-5
tracking calls 5-6
treble adjustment 4-10
troubleshooting
LAN, connecting to 2-3
monitor, connecting 2-3
optional components 1-6
positioning 2-2
power, connecting to 2-4
powering on 2-5
remote control 2-5
setting up hardware 2-1
standard components 1-5
V500 web interface
critical problems 7-8
minor issues 7-13
moderate issues 7-11
normal system behaviors 7-16
severe problems 7-9
accessing 5-2
accessing diagnostic screens 7-3
accessing system via 3-3
managing directories 5-4
managing system profiles 5-3
sending message 7-2
U
upgrading, software 3-19
© Polycom, Inc.
Index - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Administrator’s Guide for the V500 System
video
cable 1-5
cable, drawing Appendix-3
configuring 4-6
diagnostic tools 7-5
protocol 6-3
Video screen 7-5
voice algorithm, ISDN 3-13
volume
bass 4-10
master control 4-10
setting 4-10
setting on external system 4-10
sound effects 4-10
treble 4-10
W
web access port 4-14
web browser requirements 3-3
web site, for documentation 4-25
WINS name resolution 3-5
WINS server 3-5
Index - 8
www.polycom.com/videodocumentation
Download from Www.Somanuals.com. All Manuals Search And Download.
|