Polycom® RMX®
1500/2000/4000
Getting Started Guide
Version 7.0 | August 2010 | DOC2560A
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Notices
United States Federal Communication
CE Mark R&TTE Directive
Commission (FCC)
Part 15: Class A Statement. This equipment has
been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC
Rules. Test limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses and can radiate
radio-frequency energy and, if not installed and used
in accordance with the instruction manuals, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the
user will be required to correct the interference at his
or her own expense.
Polycom Inc., declares that the Polycom RMX™
2000 is in conformity with the following relevant
harmonized standards:
EN 60950-1:2001
EN 55022: 1998+A1:2000+A2:2003 class A
EN 300 386 V1.3.3: 2005
Following the provisions of the Council Directive
1999/CE on radio and telecommunication terminal
equipment and the recognition of its conformity.
Canadian Department of Communications
This Class [A] digital apparatus complies with
Canadian ICES-003.
Part 68: Network Registration Number. This
equipment is registered with the FCC in accordance
with Part 68 of the FCC Rules. This equipment is
identified by the FCC registration number.
Notice: The Industry Canada label identifies certified
equipment. This certification means that the
equipment meets telecommunication network
protective, operational and safety requirements as
prescribed in the appropriate Terminal Equipment
Technical Requirements document(s). The
Department does not guarantee the equipment will
operate to the user's satisfaction.
If requested, the FCC registration Number and REN
must be provided to the telephone company.
Any repairs to this equipment must be carried out by
Polycom Inc. or our designated agent. This
stipulation is required by the FCC and applies during
and after the warranty period.
Before installing this equipment, users should ensure
that it is permissible to be connected to the facilities
of the local telecommunications company. The
equipment must also be installed using an acceptable
method of connection. The customer should be
aware that compliance with the above conditions may
not prevent degradation of service in some situations.
Repairs to certified equipment malfunctions, may give
the telecommunications company causes to request
the user to disconnect the equipment.
United States Safety Construction Details:
•
•
All connections are indoor only.
Unit is intended for RESTRICTED ACCESS
LOCATION.
•
•
•
Unit is to be installed in accordance with the
National Electrical Code.
The branch circuit overcurrent protection shall
be rated 20 A for the AC system.
Users should ensure for their own protection that the
electrical ground connections of the power utility,
telephone lines and internal metallic water pipe
system, if present, are connected together. This
precaution may be particularly important in rural
areas.
This equipment has a maximum operating
ambient of 40°C, the ambient temperature in
the rack shall not exceed this temperature.
To eliminate the risk of battery explosion, the battery
should not be replaced by an incorrect type.
Dispose of used batteries according to their
instructions.
Caution: Users should not attempt to make such
connections themselves, but should contact the
appropriate electric inspection authority, or
electrician, as appropriate.
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Notices
Chinese Communication Certificate
Singapore Certificate
RMX 2000 complies with IDA standards G0916-07
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
RMX Main Features ............................................................................... 1-4
PCM .................................................................................................. 1-9
Entry Queue .................................................................................... 1-9
Workstation Requirements ................................................................. 1-14
Windows 7™ Security Settings .................................................. 1-15
Internet Explorer 8 Configuration .............................................. 1-17
Prerequisites .......................................................................................... 1-21
First Time Installation and Configuration . . . . . . . . . . . 2-1
Preparations ............................................................................................ 2-2
Gather Network Equipment and Address Information ........... 2-2
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
IP Network Services Required Information ....................... 2-3
Connecting Cables on the RMX 4000 ................................. 2-18
User Definition .............................................................................. 2-41
Selecting the RMX Web Client Languages ............................... 2-41
RMX’s Default Conferencing Settings ............................................... 2-42
Customizing the RMX’s Default Conferencing Settings ........ 2-45
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Starting the RMX Web Client ............................................................... 3-1
RMX 2000 Web Client Screen Components ........................................ 3-3
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Status Bar ......................................................................................... 3-6
Starting a Conference from the Conferences Pane .................. 3-16
Meeting Invitation ........................................................................ 3-31
Meeting Invitation ................................................................ 3-34
Entry Queue Access ..................................................................... 3-35
H.323 Participants ................................................................. 3-35
SIP Participants ..................................................................... 3-36
ISDN and PSTN Participants .............................................. 3-36
Dial-out Participants .................................................................... 3-37
Automatic Dial Out .............................................................. 3-37
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Message Overlay .................................................................. 3-46
Paste Conference ................................................................... 3-65
Paste Conference As ............................................................. 3-66
Changing the Video Layout of a Conference ................... 3-67
Video Forcing ........................................................................ 3-69
Enabling and Disabling Video Clarity™ .......................... 3-72
Participant Level Operations ...................................................... 3-73
Copy Cut and Paste Participant ......................................... 3-76
Copy Participant ................................................................... 3-76
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Force ............................................................................ 3-99
Recording ............................................................................. 3-100
PCM Main Menu - Level 2 ........................................................ 3-102
Drop Participant ................................................................. 3-102
Terminate Conference ........................................................ 3-103
............................................................................................... 3-103
Appendix A - Glossary . . . . . . . . . . . . . . . . . . . . . . . . . A-1
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
1
System Overview
This Getting Started Guide provides information on the installation and
basic operation of your RMX system.
Chairpersons and Operators (users who start and manage conferences for
other users) please read:
•
•
Chapter 1 – System Overview
Chapter 3 – Basic Operation
System Administrators please read:
•
•
•
Chapter 1 – System Overview
Chapter 2 – First Time Installation and Configuration
Chapter 3 – Basic Operation
For more information on configuring and managing the system, refer to
the RMX 1500/2000/4000 Administrator’s Guide included with the system.
Unless specified differently, all screen captures, Diagrams and Figures
included in this guide apply to RMX 1500, RMX 2000 and RMX 4000.
RMX 1500/2000/4000
The Polycom RMX 1500/2000/4000 Multipoint Control Unit (MCU) is a
high performance, scalable, IP-network (H.323 and SIP) and ISDN/
PSTN solution that provides the user with feature-rich and easy-to-use
multipoint voice and video conferencing.
The RMX MCU meets International Telecommunication Union -
Telecommunication Standardization Sector, (ITU-T, formerly CCITT)
standards for multipoint multimedia bridging devices, and meets ETSI
standards for telecommunication products.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1-System Overview
The RMX unit has, in addition, been designed in compliance with IETF
(Internet Engineering Task Force) – a large open international community
of network designers, operators, vendors, and researchers concerned with
the evolution of the Internet architecture and the smooth operation of the
Internet.
ISDN Endpoints
PSTN Phones
E1/T1 PRI Lines
RMX 1500/2000/4000
RMX Web Client
LAN
Endpoints
IP Phone
PC
Figure 1-1 Multipoint Video Conferencing using a Polycom RMX 1500/2000/4000
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
The Polycom RMX 1500/2000/4000 unit can be controlled via the LAN,
R
by the RMX Web Client application, using Internet Explorer installed on
the user’s workstation or the RMX Manager application. The RMX
Manager can control several RMX units (RMX 1500, RMX 2000 and
RMX 4000). For more information about the RMX Manager, see "RMX
Manager Application” on page 17-1.
In the RMX 1500/2000, RMX management and IP conferencing are
performed via a single LAN port. The networks can be separated in
Enhanced Security Environments such as the DoD environment.
In the RMX 4000, RMX management and IP conferencing are performed
via two different LAN ports. The networks can be separated in the
Enhanced Security Environment.
The RMX 1500 supports one ISDN card with 4 E1/T1 PRI lines.
On the RMX 2000/4000 a maximum of two RTM ISDN cards are
supported, each providing connection for up to either 7 E1 or 9 T1 PRI
lines.
On RMX 1500/2000/4000, E1 and T1 connections cannot be used
simultaneously.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1-System Overview
RMX Main Features
Conferencing Modes
Dynamic Continuous Presence
The dynamic Continuous Presence (CP) capability of the RMX system
enables viewing flexibility by offering multiple viewing options and
window layouts for video conferencing. By default every conference,
Entry Queue and Meeting Room has the ability to declare the maximum
CP resolution as defined for the system. This includes conferences
launched by the RMX Web Client and conferences started via the API.
CP mode conferencing is defined by:
•
Conference profile settings:
—
—
Conference Line Rate.
Video Quality selection – Motion or Sharpness.
•
Endpoint Capabilities – Participants can connect at differing line rates
using endpoints with differing capabilities.
Video Layouts in CP
Thirty-five layouts are available to accommodate different numbers of
participants and conference settings. The VUI annex to the H.264 protocol
for endpoints that transmit wide video format instead of 4CIF resolution
is also supported.
Table 1-1 Continuous Presence – Video Layouts
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Table 1-1 Continuous Presence – Video Layouts (Continued)
Telepresence Mode
TPX (Telepresence) and RPX (Realpresence) room systems are configured
with high definition cameras and displays that are set up to ensure that all
participants share a sense of being in the same room.
The RMX enables Telepresence Rooms to connect to conferences where
point-to-point connections cannot be used.
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1-System Overview
Additional video layouts have been created to give Telepresence operators
more video layout options when configuring TPX room systems. These
additional video layout options are available for selection when
Telepresence is selected in the conference profile.
Multiple Switching Modes
If the number of participants is higher than the number of video windows
in the selected layout, switching between video participants can be
performed in one of these modes:
•
Voice activation
•
•
RMX user forces participants to selected video window
Lecture Mode - The lecturer is viewed in full screen by all conference
participants, while the audience is “time-switched” in the speaker’s
view
•
Presentation Mode - When the speaker’s presentation extends beyond
a predefined time, he/she becomes the current lecturer and the
conference switches to Lecture Mode
Video Switching
In Video Switching (VSW) mode all participants see the same video
picture (full screen). Only one CIF video resource is used for each
connection.
VSW mode conferencing is defined by:
•
Conference Line Rate setting in the conference profile
—
All endpoints must connect to the conference at the same Line
Rate. Line rates range from 192kbps to 6Mb (8Mb with MPMx).
The RMX will always connect participants at the highest possible
video quality the is supported by the conference Line Rate.
•
Endpoint capabilities
—
Compliant endpoints can connect to conferences at resolutions of
up to 1920 x 1080 pixels (1080p).
The video quality for the conference is determined by the Highest Common
Mechanism and is based on the endpoint with the lowest capabilities that
is connected to the conference. The Highest Common Mechanism enables
the system to dynamically select the best video quality as endpoints
connect to and disconnect from the conference.
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Operator Conference
In Continuous Presence mode, a special conference that enables the RMX
user, acting as an operator, to assist participants without disturbing
ongoing conferences and without being heard by other conference
participants. The operator can move a participant from an Entry Queue or
ongoing conference to a private, one-on-one conversation in the Operator
conference.
Video Resolutions
Resolution Configuration for CP
The Resolution Configuration dialog box enables the RMX administrator to
modify the video resolution decision matrix, effectively creating his/her
own decision matrix. The minimum threshold line rates at which
endpoints are connected at the various video resolutions can be optimized
by adjusting the resolution sliders.
For more information see the RMX 1500/2000/4000 Administrator’s Guide
"Resolution Configuration” on page 2-12.
Video Switching
In Video Switching (VSW) mode all participants see the same video
picture (full screen). Only one CIF video resource is used for each
connection.
VSW mode conferencing is defined by:
•
Conference Profile settings:
—
Line Rate – From 192kbps to 6Mb (8Mb with MPMx). All
participants must connect at the same line rate.
—
Resolution – HD720 or HD1080.
•
•
Endpoint capabilities:
—
Participants connecting to VSW conferences must have HD or SD
capable endpoints. If not, they are connected as Secondary (Audio
Only participants).
HD_THRESHOLD_BITRATE system flag – determines the minimum
line rate at which at which an HD channel will be opened.
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1-System Overview
H.239 / People+Content
The H.239 protocol allows compliant endpoints to share content. By
default, all Conferences, Entry Queues, and Meeting Rooms launched on the
RMX have H.239 capability. This protocol is also supported in MIH
Cascading conferences.
Conferences can include a mix of endpoints that support H.239 or
People+Content.
People+Content is Polycom’s proprietary equivalent of H.239.
Video Clarity™
The Video Clarity feature applies video enhancing algorithms to incoming
video streams of resolutions up to and including SD. Clearer images with
sharper edges and higher contrast are sent back to all endpoints at the
highest possible resolution supported by each endpoint.
All layouts, including 1x1, are supported.
Video Clarity can only be enabled for Continuous Presence conferences in
MPM+ and /MPMx Modes.
IVR-Enabled Conferencing
Interactive Voice Response (IVR) is a software module that automates the
connection process and lets participants perform various operations
during ongoing conferences. The participants use their endpoints’
keypads and remote control to interact with the conference’s menu-driven
scripts using DTMF codes.
Operations that can be performed by participants or chairpersons during
a conference include:
•
•
•
•
•
Manually terminate the conference.
Mute or unmute the participant’s audio channel.
Adjust the participant’s broadcasting and listening audio volume.
Play the Help menu.
Mute or unmute undefined dial-in participants upon their connection
to the conference.
•
Request a Roll Call and stop the Roll Call names review
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
•
•
Secure and unsecure a conference.
Request individual and conference assistance.
PCM
The Personal Conference Manager (PCM) interface enables the conference
chairperson to control various conference features using his/her
endpoint’s remote control device.
The following conference operations can be performed:
•
Initiate Polycom’s Click&View™ application to change the local
screen layout.
•
•
•
Invite a participant to connect to the conference.
View and control the audio and video of each connected endpoint.
Camera Control - control the camera of a remote endpoint using
(FECC).
•
•
Control the camera of a connected endpoint.
Video Force a specific participant to a specific window of the video
layout.
•
•
•
Initiate and control recording of the conference.
Disconnect a participant.
Terminate the conference.
Entry Queue
An Entry Queue is a special routing lobby for video and audio
participants. After dialing the Entry Queue ID or dial-in number (ISDN/
PSTN), voice prompts from an IVR service are used to connect the
participants to the appropriate conference.
This service can also be used (if required) to verify the participant’s right
to start an Ad Hoc conference or to join an ongoing conference.
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1-System Overview
Conferencing Capabilities and Options
On Demand Conferencing
The following options are available to set up conferences:
New Conference – set up once, use once.
•
The conference is deleted from the MCU after it ends.
•
•
•
Meeting Rooms – set up once, use many times.
Meeting Rooms are saved in memory (using no resources) and can be
activated as many times as needed.
Ad Hoc Entry Queue – no setup, a new conference can be created when
a user dials in and enters a conference ID that is not being used by an
existing conference or Meeting Room.
Gateway calls – from IP endpoints to other participants, using the
direct dialing method, with up to 10 destination numbers contained
in a single dial string.
Permanent Conference
A Permanent Conference is an ongoing conference with no predetermined
End Time, continuing until it is terminated by an administrator, operator
or chairperson.
Scheduled Conferencing / Reservations
Reservations provide calendar-based scheduling of single or recurring
conferences. These conferences can be launched immediately or become
ongoing, at a specified time on a specified date.
Polycom Conferencing for Microsoft Outlook®
Polycom Conferencing for Microsoft Outlook is implemented by installing the
Polycom Conferencing Add-in for Microsoft Outlook on Microsoft Outlook
e-mail clients. It enables meetings to be scheduled with video endpoints
from within Outlook. The add-in also adds a Polycom Conference button in
the Meeting tab of the Microsoft Outlook e-mail client ribbon.
Connection Methods
IPv4, IPv6, ISDN and PSTN communication protocols are supported for
connection to the conference.
•
Dial-out: automatically, to pre-defined participants (line rate
detection is automatic)
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
•
Dial-in:
—
—
for participants defined in advance (IP participants only)
for undefined participants directly to a conference (IP and
ISDN/PSTN)
—
for undefined participants via a single dial Entry Queue (IP and
ISDN/PSTN)
Cascading Conferences
•
•
Simple Cascading of 2 MCUs and Star Topology.
Multi Hierarchy Cascading (MIH).
Gateway
Using a special Gateway Profile, the RMX can be used as a gateway that
provides connectivity across different physical networks such as H.323,
SIP, ISDN and PSTN. The Gateway also provides connectivity between
the ISDN/PSTN endpoints and the DMA.
Security
•
Media Encryption, available at conference and participant levels,
based on AES 128 Media Encryption and DH 1024 Key Exchange
standards.
•
•
Secured Communication Mode (SSL/TLS).
Secured conferences via DTMF codes and limited monitoring of
secured conferences.
•
•
•
•
Auditor to analyze configuration changes and unusual or malicious
activities in the RMX system.
Network security can be enhanced by separation of the Signaling and
Management Networks.
RMX Users can be disabled by the administrator, or automatically
when inactive. Disabled Users can be enabled by the administrator.
Enhanced Security Environment can be implemented.
In such an environment, the following attributes are implemented:
—
Password management:
•
•
Strong Passwords and password re-use / history rules,
password aging rules, password change frequency and
forcing password change
•
Conference and Chairman Passwords
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1-System Overview
•
•
Locking out Users
Displaying the User Login record
—
Controlling the User Sessions includes:
•
•
•
•
Limiting the maximum number of concurrent user sessions
Connection Timeout
User session timeout
Limiting the maximum number of users that can connect to
the system
Conference Management and Monitoring Features
The Polycom RMX 1500/2000/4000 Web Client provides capabilities for
management and monitoring of participants and conferences, including
the following:
•
Lecture Mode or Presentation Mode in Continuous Presence
conferences.
•
•
•
•
Far End Camera Control (FECC/LSD) in video conferences.
Automatic termination of idle (no participants) conferences.
Automatic extension of conference Duration.
Control of listening and broadcasting audio volume for individual
participants.
•
•
Auto Gain Control (AGC) noise and audio volume regulation for
individual participants.
Conference control via DTMF codes from participant’s endpoint or
telephone.
•
•
•
Entry, exit and end-of-conference indications.
Media Encryption.
Active display of all conferences and participants with option to limit
display in secured conferences.
•
Real-time monitoring of each participant’s connection status and
properties.
•
•
•
•
Multiple drag & drop of participants.
Easily accessed Call Detail Records (CDR) for administrator.
Active display of all system resources.
Closed Caption provides real-time text transcriptions or language
translations of the video conference.
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
•
•
•
Message Overlay allows messages to be sent to all participants in an
ongoing conference.
PCM enables the conference chairperson to control various
conference features using his/her endpoint’s remote control device.
Video Preview allows RMX users to preview video sent from the
participants to the conference and from the conference to the
participants.
•
•
Auto Redial when Endpoint Drops instructs the RMX to automatically
redial IP and SIP participants that have been abnormally
disconnected from the conference.
Operator Assistance & Participant Move for conferences in CP mode.
Card Configuration Modes
Three Card Configuration Modes are supported:
•
MPM Mode – Supported with MPM cards on the current, and all
previous RMX versions. Applicable to RMX 2000 only.
•
MPM+ Mode – Supported from Version 4.0, with MPM+ cards
installed in the RMX 2000 and RMX 4000. It offers:
—
—
—
Two Video/Voice Resource Capacity resource allocation modes for
increased control over system resource allocation.
Enhanced Resource Report for more accurate system
management.
Additional video resolutions and video quality.
•
MPMx Mode – Supported from Version 7.0, with MPMx cards
installed in the RMX 1500 and RMX 4000. Over and above MPM+ it
offers:
—
—
—
—
Increased resource capacity.
Additional symmetric HD resolutions.
H.264 High Profile.
Additional line rates.
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1-System Overview
Workstation Requirements
The RMX Web Client and RMX Manager applications can be installed in an
environment that meets the following requirements:
•
Minimum Hardware – Intel® Pentium® III, 1 GHz or higher,
1024 MB RAM, 500 MB free disk space.
•
Workstation Operating System – Microsoft® Windows® XP, Vista®,
Windows® 7.
•
•
Network Card – 10/100 Mbps.
Web Browser - Microsoft® Internet Explorer® Version 6 or higher.
.Net Framework 2.0 is required and installed automatically.
If ActiveX installation is blocked please see the RMX 1500/2000/4000
Administrator’s Guide, "ActiveX Bypass” on page 18-111.
When installing the RMX Web Client, Windows Explorer >Internet Options>
Security Settings must be set to Medium or less.
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Windows 7™ Security Settings
If Windows7 is installed on the workstation, Protected Mode must be
disabled before downloading the Version 7.0 software to the workstation.
To disable Protected Mode:
1
In the Internet Options dialog box, click the Security tab.
The Security tab is displayed.
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1-System Overview
2
Clear the Enable Protected Mode check box for each of the following
tabs:
—
—
—
Internet
Local intranet
Trusted sites
1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
3
After successful connection to RMX, the Enable Protected Mode check
boxes can be selected to enable Protected Mode for the following tabs:
—
—
Internet
Local intranet
Internet Explorer 8 Configuration
When using Internet Explorer 8 to run the RMX Web Client or RMX
Manager applications, it is important to configure the browser according
to the following procedure.
To configure Internet Explorer 8:
1
2
Close all browsers running on the workstation.
Use the Windows Task Manager to verify that no iexplore.exe processes
are running on the workstation. If any processes are found, use the
End Task button to end them.
3
4
Open Internet Explorer but do not connect to the RMX.
In the Internet Explorer menu bar select Tools >> Internet Options.
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1-System Overview
The Internet Options dialog box is displayed with General tab open.
5
In the Browsing history section, click the Delete button.
1-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
The Delete Browsing History dialog box is displayed.
6
7
8
9
Select the Temporary Internet files and Cookies check boxes.
Click the Delete button.
The Delete Browsing History dialog box closes and the files are deleted.
In the Internet Options dialog box, click the Settings button.
1-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1-System Overview
The Temporary Internet Files and History Settings dialog box is
displayed.
10 Click the View objects button.
1-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
The Downloaded Program Files folder containing the installed Program
Files is displayed.
11 Select the CEMAClassLoaderCntl Object file
12 Press the Delete key on the workstation.
13 Close the Downloaded Program Files folder and the Temporary Internet
Files and History Settings dialog box.
14 In the Internet Options dialog box, click the OK button to save the
changes and close the dialog box.
Prerequisites
This manual assumes the user has the following knowledge:
•
Familiarity with Windows® XP or Vista® operating systems and
interface.
•
•
Familiarity with Microsoft® Internet Explorer® Version 6 or higher.
Basic knowledge of video conferencing concepts and terminology.
1-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1-System Overview
1-22
Download from Www.Somanuals.com. All Manuals Search And Download.
2
First Time Installation and
Configuration
First Time Installation and Configuration of the Polycom RMX 1500/2000/4000
consists of the following procedures:
Preparations
1
Preparations:
—
Gather Network Equipment and Address Information - get the
information needed for integrating the RMX into the local
network.
Unpack the RMX.
Hardware
Installation
and
—
—
Setup
Modify the Management Network parameters on the USB Key.
2
3
Hardware Installation and Setup
First Entry
Power-up and
Configuration
—
—
Mount the RMX in a rack.
Connect the necessary cables.
First Entry Power-up and Configuration
—
—
—
—
—
Power up the RMX.
Register the RMX.
Connect to the RMX
Configure the Default IP Network Service.
Configure the ISDN/PSTN Network Service.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Preparations
Gather Network Equipment and Address Information
IP Services
The IP addresses and network parameters which enable communication
between the RMX, its management application and the conferencing
devices are organized in two IP services:
Preparations
•
•
Management Network (Control Unit)
Default IP Service (Conferencing Service)
Hardware
Installation
and
During the First Entry Configuration, the parameters of these two network
services are modified to comply with your local network settings.
Setup
Management Network
The Management Network enables communication between the RMX
Control Unit and the RMX Web Client and is used to manage the RMX.
First Entry
Power-up and
Configuration
The RMX is shipped with default IP addresses as listed in Table 2-1.
Management Network Definition
The definition of the Management Network can be done by two methods:
•
USB key (recommended method) – The system is shipped with a
USB key containing the default IP addresses for the control unit and
the shelf management.
These defaults are first modified in the PC and then uploaded to the
RMX.
•
Direct connection – Creating a private network between the RMX
and the computer and modifying the management network
parameters using Fast Configuration Wizard in the RMX Web Client.
For more information, see the RMX 1500/2000/4000 Administrator’s
Guide, ”Configuring Direct Connections to RMX” on page G-1.
Default IP Service (Conferencing Service)
The Default IP Service (Conferencing Service) is used to configure and
manage communications between the RMX and conferencing devices.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
IP Network Services Required Information
When installing an RMX unit, these default IP addresses must be
modified to your local network settings. Therefore it is important that
before powering the RMX unit up for the first time, that you obtain the
information needed to complete the Local Network Settings section of
the table from your network administrator.
For RMX 1500, the network administrator should allocate three IP
addresses in the local network for an MCU with a MPMx card.
For RMX 2000, the network administrator should allocate four IP
addresses in the local network for an MCU with one MPM/MPM+/MPMx
card and five IP addresses for an MCU with two MPM/MPM+/MPMx
cards.
For RMX 4000, the network administrator should allocate four IP
addresses in the local network for an MCU with one MPM+/MPMx card
and up to seven IP addresses for an MCU with up to four MPM+/MPMx
cards.
Table 2-1 Network Equipment and Address Information
Parameter
Factory Default
Local Network Settings
Control Unit
IP Address
192.168.1.254
Control Unit
Subnet Mask
255.255.255.0
192.168.1.1
Default Router IP
Address
Shelf Management IP
Address
192.168.1.252
Signaling Host IP
address
–
–
Media Board IP
address (MPM 1)
Media Board IP
address (MPM 2)
RMX 2000/4000 only
–
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Table 2-1 Network Equipment and Address Information (Continued)
Parameter
Factory Default
Local Network Settings
Media Board IP
address (MPM 3)
RMX 4000 only
–
Media Board IP
address (MPM 4)
RMX 4000 only
–
Gatekeeper IP
address (optional)
–
–
–
DNS IP address
(optional)
SIP Server IP
address (optional)
ISDN/PSTN Services
The ISDN/PSTN Network Service is used to define the properties of the
ISDN/PSTN switch and the ISDN lines running from the ISDN/PSTN
switch to the ISDN card installed in the RMX.
Before configuring the ISDN/PSTN Network Service, obtain the
following information from your ISDN/PSTN Service Provider:
•
•
•
•
•
Switch Type
Line Coding and Framing
Numbering Plan
Numbering Type
Dial-in number range
If the RMX is connected to the public ISDN Network, an external CSU or similar
equipment is needed.
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Unpacking the RMX
Unpacking the RMX 1500
To unpack and lift the RMX 1500:
1
When you receive the RMX 1500 packing case, inspect the equipment
for damage and verify that the components match the packing slip.
2
Open the top cover of the RMX 1500 packing case and make sure that
the Installation Accessories kit contains the power cables and a USB
Key.
3
Remove the top cover, lift the RMX 1500 from the package and place
it on a flat surface.
Write down the RMX’s serial number that is on a sticker on the back of the unit.
It will be needed for product registration later in the process.
Unpacking the RMX 2000
To unpack and lift the RMX 2000:
1
When you receive the RMX 2000 packing case, inspect the equipment
for damage and verify that the components match the packing slip.
2
Open the top cover of the RMX 2000 packing case and make sure that
the Installation Accessories kit contains the power cables and a USB
Key.
3
Remove the top cover, lift the RMX 2000 from the package and place
it on a flat surface.
Write down the RMX’s serial number that is on a sticker on the back of the unit.
It will be needed for product registration later in the process.
Unpacking the RMX 4000
To unpack and lift the RMX 4000:
1
2
3
When you receive the RMX 4000 packing case, inspect the equipment
for damage and verify that the components match the packing slip.
The RMX 4000 is shipped in a packing case with Stratocell®
packaging, and the top cover must be unlocked and lifted.
Open the top cover of the packing case.
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Two boxes are placed on the top Stratocell®, labelled:
—
Installation Accessories. This kit contains the power cables and a
Disk-on Key (DOK).
—
Rack Installation Accessories. This kit contains the accessories for
the 19” & 23” racks as follows:
Table 2-2 19” & 23” Rack Installation Accessories Package
Item ID
Description
Quantity
MEC2474A-L0
Chassis runner for rack installation
on the RMX 4000. 19” & 23” racks
both require that these runners be
installed on the rack.
2
MEC2475A-L0
23" bracket to be fitted to the front of
the RMX 4000.
2
Make sure that boxes contain all the required parts.
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
4
Remove the boxes and top Stratocell® and open the anti-static plastic
bag wrapping the RMX.
5
Holding the handle on each side, lift the RMX 4000 from the box, and
place it on a flat surface or in a rack. Remove any packaging material
prior to positioning the RMX 4000.
Attention:
Two people are required to lift the MCU out of the box and when installing it in a
rack.
Write down the RMX’s serial number that is on a sticker on the back of the unit.
It will be needed for product registration later in the process.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Modifying the Factory Default Management Network
Settings on the USB Key
The USB key contains a text file, lan.cfg, which holds the factory default IP
address parameters. These parameters must be modified to your local
network settings using the LAN Configuration Utility, also on the USB key.
To modify the USB key settings:
1
Take the USB Key from the Installation Accessories kit and insert it into
the PC workstation and double-click LanConfigUtility.exe to start
the utility.
The LAN Configuration Utility dialog box opens.
2
Modify the following parameters in the utility’s dialog box using the
information supplied by your network administrator.
—
—
—
—
Control Unit IP Address
Shelf Management IP Address
Subnet Mask
Default Router IP Address
3
4
Click OK.
Remove the USB Key from the PC.
The USB key is required for first entry power-up.
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Hardware Installation and Setup
The RMX 1500/RMX 2000 unit should be mounted in a 19”rack in a well
ventilated area. The RMX 4000 unit can be mounted in a 19” or 23”rack in
a well ventilated area. It is important to adhere to the Site Requirements as
described in the RMX 1500 & RMX 1500/2000/4000 Hardware Guides, ”Site
Requirements” on page 1-3.
Installing the RMX 1500
For detailed instructions, precautions and requirements for installing the RMX
1500 refer to the Polycom RMX 1500 Hardware Guide.
The following procedures have to be performed to install the RMX 1500 in
your site:
•
•
•
Installing the RMX in a rack or as a standalone
Connecting the RMX 1500 to the power source
Connecting the network (LAN, IP and ISDN) cables to the RMX.
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Mounting the RMX 1500 in a Rack
There are two methods for installing the RMX in a 19” rack:
•
Using rack brackets on the RMX 1500– Install rack brackets,
supplied by the rack manufacturer, in the rack. Mount the RMX 1500
on top of the rack brackets. Fasten the RMX to the rack with screws
through the four holes in the RMX’s front mounting brackets.
•
Using a shelf – Install the shelf, supplied by the rack manufacturer,
in the rack. Mount the RMX on the shelf. Fasten the RMX to the rack
with screws through the four holes in the RMX’s front mounting
brackets.
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Connecting Cables on the RMX 1500
To connect the cables:
•
For the RTM-IP 1500 module:
—
—
Connect the Media cable to LAN 2 port.
Connect the Network cables to the MNG (Signaling) port &
MNGB (Management Network) port.
—
(Optional) Connect the Shelf Management cable to the Shelf port.
•
For the RTM ISDN 1500 module:
Connect the E1/T1 cables to their PRI (1-4) ports.
—
E1/T1 PRI
LAN 2; media, MNG; signaling,
Power Cable
Connection(s)
MNGB; management & Shelf
Figure 2-1 RMX 4000 Rear Panel View with AC Power and Communication
Cables
The LAN 1, LAN3, LAN4 and Modem ports are not be used and the plastic caps
covering those ports should not be removed.
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Installing the RMX 2000
For detailed instructions, precautions and requirements for installing the RMX
2000 refer to the Polycom RMX 2000 Hardware Guide.
•
The following procedures have to be performed to install the RMX
2000 in your site:
•
•
•
Installing the RMX in a rack or as a standalone
Connecting the RMX 2000 to the power source
Connecting the network (LAN, IP and ISDN) cables to the RMX
Mounting the RMX 2000 in a Rack
There are two methods for installing the RMX in a 19” rack:
•
Using rack brackets on the RMX 2000– Install rack brackets,
supplied by the rack manufacturer, in the rack. Mount the RMX 2000
on top of the rack brackets. Fasten the RMX to the rack with screws
through the four holes in the RMX’s front mounting brackets.
•
Using a shelf – Install the shelf, supplied by the rack manufacturer,
in the rack. Mount the RMX on the shelf. Fasten the RMX to the rack
with screws through the four holes in the RMX’s front mounting
brackets.
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Connecting Cables on the RMX 2000
Do not remove the protective caps from LAN1, LAN3 and ShMG ports.
Connect the following cables to the back panel:
•
•
•
Power cable
LAN cable to LAN 2 Port
E1/T1 Cables to PRI Ports
E1/T1 PRI Connection
LAN 2 Connection
Power
Cable
To maximize conferencing performance, especially in high bit rate call
environments, a 1Gb connection is recommended.
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Installing the RMX 4000
The following procedures have to be performed to install the RMX 4000 in
your site:
•
•
•
Mounting the RMX in a rack
Connecting the RMX 4000 to the power source
Connecting the network (LAN, IP and ISDN) cables to the RMX
Mounting the RMX 4000 in a Rack
Either place the RMX 4000 on a hard, flat surface such as a desktop or
mount it on a 19”/23” rack.
For a detailed description of the safety requirements and precautions and the
installation of the RMX 4000 as a standalone, in a 23” rack, or reverse mounting
the RMX 4000 on a 19” rack, see the RMX 4000 Hardware Guide.
To install the RMX 4000 in a 19”rack:
•
Using rack brackets on the RMX 4000
—
—
—
Install chassis runners supplied by Polycom, in the rack.
Mount the RMX 4000 on top of the rack brackets.
Fasten the RMX to the rack with screws through the eight holes
in the RMX’s front mounting brackets.
•
Using a shelf
—
—
—
Install the shelf, supplied by the rack manufacturer, in the rack.
Mount the RMX on the shelf.
Fasten the RMX to the rack with screws through the four holes in
the RMX’s front mounting brackets.
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Connecting the RMX 4000 to the Power Sources
The size of the protective earthing conductor & cable should be a minimum of
10AWG.
Connect the following power cables to the RMX 4000 back panel:
AC Power Supply connections:
1
Insert power cables to each of the three AC Power Entry Modules
(PEMs).
Power Cables
Figure 2-2 RMX 4000 Rear Panel View with AC Power
DC Power Supply connections:
On the DC Power Rail Modules set the two circuit breakers to OFF.
1
Two types of circuit breakers can be installed on the DC Power Rail Module
(PRM). For more information, see the RMX 4000 Hardware Guide.
2
Ensure that the cables from the Main that supplies electricity to the
DC power units are OFF or disconnected.
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
3
4
Remove the transparent plastic caps on the terminal block.
Using the two wires of an 10 AWG cable running from the DC power
distribution unit, connect the black wire into the -48VDC terminal
block and the red wire to the RTN terminal block.
•
A 10 AWG cable must be used to connect the mains with the RMX 4000 DC
Power Rail Model.
•
•
The supply wires for DC version must be terminated using quick connectors.
Extension cords may not be used.
ESD connector
Ground connector
Circuit breaker - ON
position
Circuit breaker - OFF
position
Blank panel
-48 VDC
RTN
The center PRM slot/module is fitted with a blank panel and the slot cannot be
used on a system with DC Voltage.
5
Connect the green or green-yellow wire to the system single-point
M6x15 “Ground” bolt.
The rating of the protective earthing conductor should be a minimum of 10AWG.
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
If the unit is rack mounted, the single-point ground on the MCU must
be connected to the rack with a single conductor and fixed as to
prevent loosening. When using bare conductors, they must be coated
with an appropriate antioxidant compound before crimp connections
are made. Tinned, solder-plated or silver plated connectors do not
have to be prepared in this manner.
6
7
8
Replace the transparent plastic caps on the terminal block.
Turn ON the Main that supplies power to the RMX.
Turn ON the circuit breaker on each of the DC Power Rail Modules.
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Connecting Cables on the RMX 4000
To connect the cables (AC and DC systems):
•
RTM-IP 4000:
—
—
—
Connect the Management Network cable to LAN 2.
Connect the Signalling cable to LAN 3.
Connect the Shelf Management cable to LAN 6.
•
•
For each installed RTM LAN - Connect the LAN cable to LAN 2.
For each installed RTM ISDN:
—
—
Connect the E1/T1 cables to their PRI Ports.
Connect the LAN cable to LAN 1.
LAN Connections to RTM LAN
E1/T1 Connection to RTM ISDN
Signalling
Network
Management
Network
Shelf
Manage-
ment
Off/On
switch
Power Cables
Figure 2-3 RMX 4000 Rear Panel View with AC Power and Communication
Cables
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
First Entry Power-up and Configuration
There are four procedures necessary for setup of the new RMX. It is
important that they are performed in the following sequence:
Preparations
1
2
3
4
First-time Power-up
Product Registration.
Connection to MCU.
Hardware
Installation
and
Modifying the Default IP and ISDN/PSTN Service Settings (Fast
Configuration Wizard).
Setup
First Entry
Power-up and
Configuration
Procedure 1: First-time Power-up
To power-up for the first time using the USB key:
1
Insert the USB key containing the modified IP addresses in USB port
on the RMX 1500 front panel and RMX 2000/4000 back panel.
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
2
Power the RMX On.
AC System - Turn ON the power by pressing on the power switch
located on the rear panel of the RMX 1500/2000/4000.
DC System (RMX 4000) - Turn ON the Main that supplies power to
the RMX and then turn ON each of the DC power rail modules.
The parameters in the lan.cfg file are uploaded from the USB key to
the RMX’s memory and applied during the power-up sequence.
System power-up sequence may take up to five minutes.
During the First-time Power-up the red ERR LED on the RMX’s front
panel remains ON until both the Management and IP Network Services
have been defined.
When the RMX's configuration is completed (including the
Management and IP Network Services), and if there are no System
Errors, the green RDY LED on the CNTL module (on the RMX’s front
panel) turns ON.
3
Remove the USB key.
Procedure 2: Product Registration
Before the RMX can be used, it is necessary to register the product and
obtain an Activation Key.
During first-time power-up, the Product Activation dialog box is displayed,
requesting you to enter an Activation Key.
Obtaining the Activation Key
1
Access the Service & Support page of the Polycom website at:
http://support.polycom.com
2
3
4
Login with your Email Address and Password or register as a new user.
Select Product Registration.
Follow the on-screen instructions for Product Registration and Product
Activation. (The RMX’s serial number is on a sticker on the back of the
unit, if needed.)
5
When the Product Activation Key is displayed, write it down or copy it
for later pasting into the Activation Key field of the Product Activation
dialog box.
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Procedure 3: Connection to MCU
If Windows7™ is installed on the workstation, Protected Mode must be
disabled before connecting to the MCU running Version 6.0 software.
For more information see ”Windows 7™ Security Settings” on page 1-12.
1
Start the RMX Web Client application on the workstation.
a
In the browser’s address line, enter the IP address of the Control
Unit in the format: http://<Control Unit IP Address>, as
defined in the USB key.
b
Press Enter.
The RMX Web Client Login screen is displayed.
2
In the RMX Web Client Login screen, enter the default Username
(POLYCOM) and Password (POLYCOM) and click Login.
The RMX Web Client opens and the Product Activation dialog box
appears with the serial number filled in:
3
4
In the Activation Key field, enter or paste the Product Activation Key
obtained earlier.
Click OK.
As no Default IP Network Service is defined, the system automatically
starts the Fast Configuration Wizard.
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Procedure 4: Modifying the Default IP Service and ISDN/
PSTN Network Service Settings
The Fast Configuration Wizard assists in configuring the Signaling Network
Service. It starts automatically if no Signaling Network Service is defined.
This happens during First Time Power-up, before the service has been
defined or if the Signaling Service has been deleted, followed by an RMX
restart.
The IP Management Service tab in the Fast Configuration Wizard is enabled
only if the factory default Management IP addresses were not modified.
On the RMX 1500, RMX 2000 and RMX 4000, IPv4 is the default protocol for
setting the Network Service in the Fast Configuration Wizard.
If IPv6 addressing is required, complete the Fast Configuration Wizard and
then:
1 Modify the Management Network to use IPv6 addressing or IPv4 and IPv6
addressing.
2 Restart the RMX.
3 Use the Fast Configuration Wizard which will now include IPv6 addressing
or IPv4 & IPv6 addressing options to configure the Signaling Network
Service.
For detailed description of the IP Network Services, see the RMX 1500/2000/
4000 Administrator’s Guide.
2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Table 2-3 Fast Configuration Wizard – IP Signaling
Field
Description
Network Service
Name
The name Default IP Service is assigned to the IP
Network Service by the Fast Configuration Wizard.
This name can be changed.
Note: This field is displayed in all IP Signaling dialog
boxes and can contain character sets that use
Unicode encoding.
Signaling Host
IP Address
Enter the address to be used by IP endpoints when
dialing in to the MCU.
Dial out calls from the RMX are initiated from this
address.
This address is used to register the RMX with a
Gatekeeper or a SIP Proxy server.
Media Card 1-4
IP Addresses
Enter the IP address(es) of the media card (s)
(MPM/MPM+/MPMx 1 and MPM/MPM+/MPMx 2-4
(if installed)) as provided by the network
administrator. Endpoints connect to conferences
and transmit call media (video, voice and content)
via these addresses.
Subnet Mask
Enter the subnet mask of the MCU.
Default value: 255.255.255.0.
If Secured Communication is required on the RMX: complete the Fast
Configuration Wizard, Login, install the Certificate and then enable Secured
Communication Mode.
2
Click Next.
2-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
3
Enter the required Routers information in the dialog box.
Table 2-4 Fast Configuration Wizard – Routers
Field
Description
Default Router
IP Address
Enter the IP address of the default router.
4
Click Next.
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
5
Enter the required DNS information in the dialog box.
Table 2-5 Fast Configuration Wizard – DNS
Field
Description
MCU Host Name
Enter the name of the MCU on the network.
Default name is RMX.
DNS
Select:
•
•
Off – if DNS servers are not used in the network.
Specify – to enter the IP addresses of the DNS
servers.
Note: The IP address fields are enabled only if
Specify is selected.
Register Host
Names
Automatically to
DNS Server
Select this option to automatically register the MCU
Signaling Host and Shelf Management with the DNS
server.
Local Domain
Name
Enter the name of the domain where the MCU is
installed.
Primary DNS
The static IP address of the primary DNS server.
Server IP Address
2-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
6
7
Click Next.
Select the IP Network Type: H.323, SIP or H.323 & SIP.
8
9
Click Next.
If you selected SIP only, go to Step 13.
10 Enter the required Gatekeeper information in the dialog box.
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Table 2-6 Fast Configuration Wizard – Gatekeeper
Field
Description
Gatekeeper
Select Specify to enable configuration of the
gatekeeper IP address.
When Off is selected, all gatekeeper options are
disabled.
Primary Gatekeeper
IP Address or
Name
Enter either the gatekeeper’s host name (if a DNS
Server is used) or IP address.
MCU Prefix in
Gatekeeper
Enter the string with which the MCU registers itself
with the gatekeeper.
The gatekeeper uses this string to identify the MCU
when forwarding calls to it.
H.323 endpoints use this number as the first part of
their dial-in string when dialing the MCU.
Aliases
Alias
The alias that identifies the RMX’s Signaling Host
within the network. Up to five aliases can be defined
for each RMX.
Note: When a gatekeeper is specified, at least one
prefix or alias must be entered in the table.
Type
The type defines the format in which the card’s alias
is sent to the gatekeeper. Each alias can be of a
different type:
•
•
•
H.323 ID (alphanumeric ID)
E.164 (digits 0-9, * and #)
Email ID (email address format,
e.g. abc@example.com)
•
Participant Number (digits 0-9, * and #)
Note: Although all types are supported, the type of
alias to be used depends on the gatekeeper’s
capabilities.
11 Click Next.
12 If you selected H.323 only, go to Step 15.
2-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
13 Enter the required SIP Server information in the dialog box.
Table 2-7 Fast Configuration Wizard – SIP Server
Field
Description
SIP Server
Select:
•
•
Specify – to manually configure SIP servers.
Off – if SIP servers are not present in the
network.
SIP Server IP
Address
Enter either the IP address of the preferred SIP
server or its host name (if a DNS server is used).
Transport Type
Select the protocol that is used for signaling between
the MCU and the SIP Server or the endpoints
according to the protocol supported by the SIP
Server:
UDP – Select this option to use UDP for signaling.
TCP – Select this option to use TCP for signaling.
TLS – The Signaling Host listens on secured port
5061 only and all outgoing connections are
established on secured connections. Calls from SIP
clients or servers to non secured ports are rejected.
2-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Table 2-7 Fast Configuration Wizard – SIP Server (Continued)
Field
Description
Transport Type
(cont.)
The following protocols are supported:
•
•
•
TLS 1.0
SSL 2.0
SSL 3.0.
14 Click Next.
Enter the required Security information in the dialog box.
Table 2-8 Fast Configuration Wizard – Security
Field
Description
Authentication
User Name
Enter the conference, Entry Queue or Meeting
Room name as registered with the proxy.
This field can contain up to 20 ASCII characters.
Authentication
Password
Enter the conference, Entry Queue or Meeting
Room password as defined in the proxy.
This field can contain up to 20 ASCII characters.
15 Click Next.
2-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
The IP Network Service is created and confirmed.
16 Click OK.
During the initial RMX setup, if the system detects the presence of the
RTM ISDN card, the ISDN /PSTN Network Service definition screens of the
Fast Configuration Wizard are enabled.
If there is no RTM ISDN card in the RMX or if you do not want to define
an ISDN/PSTN Network Service, go to Step 33..
A new ISDN/PSTN Network Service can be defined even if no RTM ISDN card is
installed in the system but only via the ISDN/PSTN Network Service ->Add New
Service dialog box.
The Fast Configuration Wizard’s ISDN/PSTN configuration sequence
begins with the ISDN/PSTN dialog box:
2-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
17 Define the following parameters:
Table 2-9 Fast Configuration Wizard – ISDN Service Settings
Field
Description
Network Service
Name
Specify the service provider’s (carrier) name or
any other name you choose, using up to 20
characters. The Network Service Name identifies
the ISDN/PSTN Service to the system.
Default name: ISDN/PSTN Service
Note: This field is displayed in all ISDN/PSTN
Network Properties tabs and can contain
character sets that use Unicode encoding.
Span Type
Select the type of spans (ISDN/PSTN) lines,
supplied by the service provider, that are
connected to the RMX. Each span can be defined
as a separate Network Service, or all the spans
from the same carrier can be defined as part of
the same Network Service.
Select either:
•
•
T1 (U.S. – 23 B channels + 1 D channel)
E1 (Europe – 30 B channels + 1 D channel)
Default: T1
Note: Only one Span Type (E1 or T1) is supported
on the RMX. If you define the first span as type E1
all other spans that you may later define must also
be of type E1.
Service Type
PRI is the only supported service type. It is
automatically selected.
18 Click Next.
2-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
The PRI Settings dialog box opens.
19 Define the following parameters:
Table 2-10 Fast Configuration Wizard – PRI Settings
Field
Description
Default Num Type
Select the Default Num Type from the list.
The Num Type defines how the system handles the
dialing digits. For example, if you type eight dialing
digits, the Num Type defines whether this number is
national or international.
If the PRI lines are connected to the RMX via a
network switch, the selection of the Num Type is
used to route the call to a specific PRI line. If you
want the network to interpret the dialing digits for
routing the call, select Unknown.
Default: Unknown
Note: For E1 spans, this parameter is set by the
system.
2-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Table 2-10 Fast Configuration Wizard – PRI Settings (Continued)
Field
Description
Num Plan
Select the type of signaling (Number Plan) from the
list according to information given by the service
provider.
Default: ISDN
Note: For E1 spans, this parameter is set by the
system.
Net Specific
Select the appropriate service program if one is
used by your service provider (carrier).
Some service providers may have several service
programs that can be used.
Default: None
Dial-out Prefix
Enter the prefix that the PBX requires to dial out.
Leave this field blank if a dial-out prefix is not
required.
The field can contain be empty (blank) or a numeric
value between 0 and 9999.
Default: Blank
20 Click Next.
The Span Definition dialog box opens.
2-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
21 Define the following parameters:
Table 2-11 Fast Configuration Wizard – Spans Definition
Field
Description
Framing
Select the Framing format used by the carrier for
the network interface from the list.
•
•
For T1 spans, default is SFSF.
For E1 spans, default is FEBE.
Side
Select one of the following options:
•
•
•
User side (default)
Network side
Symmetric side
Note: If the PBX is configured on the network side,
then the RMX unit must be configured as the user
side, and vice versa, or both must be configured
symmetrically.
Line Coding
Switch Type
Select the PRI line coding method from the list.
•
•
For T1 spans, default is B8ZS.
For E1 spans, default is HDB3.
Select the brand and revision level of switch
equipment installed in the service provider’s central
office.
•
•
For T1 spans, default is AT&T 4ESS.
For E1 spans, default is EURO ISDN.
22 Click Next.
2-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
The Phones dialog box opens.
23 Click Add to define dial-in number ranges.
The Add Phone Number dialog box opens.
24 Define the following parameters:
Table 2-12 Fast Configuration Wizard – Add Phone Numbers
Field
Description
First Number
Last Number
The first number in the phone number range.
•
•
A range must include at least two dial-in numbers.
A range cannot exceed 1000 numbers.
25 Click OK.
The new range is added to the Dial-in Phone Numbers table.
26 Optional. Repeat steps 23 to 24 to define additional dial-in ranges.
27 In the Phones tab enter the MCU CLI (Calling Line Identification).
2-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
With dial-in connections, the MCU CLI indicates the MCU’s number
dialed by the participant. In a dial-out connection, indicates the MCU
(CLI) number as seen by the participant.
28 Click Save & Continue.
After clicking Save & Continue, you cannot use the Back button to
return to previous configuration dialog boxes.
The ISDN/PSTN Network Service is created and is added to the ISDN/
PSTN Network Services list.
If the system cannot create the ISDN/PSTN Network Service, an error
message is displayed indicating the cause and allowing you access
the appropriate dialog box in the Fast Configuration Wizard for
corrective action.
29 Click OK to continue the configuration.
The Spans dialog box opens displaying the following read-only fields:
Attached
Spans
Spans
Table
—
ID – the connector on the RTM ISDN card (PRI1 to PRI12).
2-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
—
Slot – the MPM/MPM+/MPMx card that the RTM ISDN /
RTM ISDN 1500 card is connected to (RMX 2000: MPM 1/MPM2
RMX 4000: MPM1/MPM2/MPM3/MPM4).
On the RMX 1500, the Slot field does not appear.
—
—
Service – the ISDN/PSTN Network Service to which the span is
assigned.
Clock Source – indicates if ISDN signaling synchronization is
being supplied by the Primary or Secondary clock source. The first
span to synchronize becomes the Primary clock source.
—
State – the System Alert level of the span (Major, Minor). If there
are no span related alerts, this column contains no entries.
30 Click the check boxes in the Attached field to attach spans (E1 or T1
PRI lines) to the network service named in the Network Service Name
field.
The Spans Table displays the configuration of all spans and all ISDN
network services in the system.
When using the Fast Configuration Wizard during First Entry
Configuration, you are defining the first ISDN/PSTN Network Service in
the system. Spans can only be attached to this service.
Additional ISDN/PSTN Network Services can be defined by using the
ISDN/PSTN Network Services > New PSTN Service button in the
RMX Web Client.
Spans can be attached to, or moved between ISDN network services
by using the ISDN/PSTN Network Services > ISDN Properties >
Spans tab in the RMX Web Client.
Each ISDN RTM card can support either 7 E1 or 9 T1 PRI lines (E1
and T1 connections cannot be used simultaneously).
31 Click Next.
2-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
The System Flags dialog box is displayed.
32 Enter the required System Flags information in the dialog box.
Table 2-13 Fast Configuration Wizard – System Flags
Field
Description / Default
The number of digits of the
Conference ID to be assigned
by the MCU.
Conference
ID Length
(MCU)
Range: 2-16 (Default: 5)
Minimum
Conference
ID Length
(User)
The minimum number of digits
that the user must enter when
manually assigning a numeric
ID to a conference.
Note: Selecting 2
digits limits the
number of
simultaneous ongoing
conferences to 99.
Range: 2-16 (Default: 4)
Maximum
Conference
ID Length
(User)
The maximum number of digits
that the user can enter when
manually assigning a Numeric
ID to a conference.
Range: 2-16 (Default: 8)
MCU Display
Name
The MCU name is displayed on the endpoint’s screen.
Default name: Polycom RMX 1500/2000/4000
2-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Table 2-13 Fast Configuration Wizard – System Flags (Continued)
Field
Description / Default
Terminate
Conference
when
When Yes is selected (default), the conference ends
when the chairperson exits even if there are other
participants connected.
Chairperson
Exits
When No is selected, the conference automatically ends
at the predefined end time, or when all the participants
have disconnected from the conference.
Auto Extend
Conferences
When Yes is selected (default), allows conferences
running on the RMX to be automatically extended as long
as there are participants connected and there are
available resources.
The maximum extension time allowed by the MCU is 30
minutes.
These flags can be modified later, if required, by selecting the System
Configuration option from the Setup menu. For more information, see
the RMX 1500/2000/4000 Administrator’s Guide, ”System Configuration”
on page 18-5.
33 Click Save & Close.
The RMX confirms successful configuration.
34 In the Success Message box, click OK.
35 In the Reset Confirmation dialog box, click Yes.
36 In the Please wait for system reset message box, click OK.
System restart may take up to five minutes.
37 Refresh the browser periodically until the Login screen is displayed.
38 When the Login screen is displayed, enter your Username and
Password and click Login.
2-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
On first entry, the default Username and Password are both POLYCOM.
In the RMX Web Client’s Main Screen an MCU State indicator displays
a progress indicator
showing the time remaining
until the system start-up is complete.
39 Create a new User with Administrator permissions and delete the
default User (POLYCOM).
For system security reasons the system is not fully configured until
this step has been performed.
For more information see the RMX 1500/2000/4000 Administrator’s
Guide, "Users, Connections and Notes” on page 12-1.
40 The system is now fully configured and if there are no System Errors,
the green RDY LED on the CNTL module (on the RMX’s front panel)
turns ON.
The Fast Configuration Wizard configures the Default IP Network Service with
common parameters. Specific or additional settings (e.g. for ICE, or Secured
Mode) should be performed once the initial configuration is complete. For
detailed description of the IP Network Services, see the RMX 1500/2000/4000
Administrator’s Guide.
User Definition
The RMX is shipped with a default Administrator user called POLYCOM.
Once you have defined other authorized administrator users, it is
recommended to remove the default user to prevent unauthorized users
from logging into the system.
For more information, see the RMX 1500/2000/4000 Administrator’s Guide
”Deleting a User” on page 12-4.
Selecting the RMX Web Client Languages
By default, the RMX Web Client interface is displayed only in English.
However, the system administrator can choose the languages available
for selection on the Login screen. These languages are represented by
flags.
To choose the languages for selection in the Login screen:
1
On the RMX menu, click Setup > Multilingual Setting.
2-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
2
Click the check boxes of the languages to appear in the Login screen
of the RMX Web Client. For more information see the RMX 1500/2000/
4000 Administrator’s Guide ”Multilingual Setting” on page 18-86.
If the selected language is not supported by the browser or the
workstation’s Operating System, the RMX Web Client is displayed in
English.
3
4
Click OK.
Log out and reconnect to the RMX.
The Login screen will display the flags of the selected languages.
RMX’s Default Conferencing Settings
The RMX is shipped with default pre-configured conferencing entities,
which allow RMX users and participants to start ongoing conferences
without further configuration.
The default conferencing entities are:
Table 2-14 Conferencing Entities
Entity
Description
Meeting Rooms
Conferences saved on the MCU without using resources.
They are activated when the first participant dials in.
There are four Meeting Rooms ready for use:
Name
ID
Maple_Room
Oak_Room
Juniper_Room
Fig_Room
1001
1002
1003
1004
Each Meeting Room uses the default Conference Profile
called Factory Video Profile running at 384Kbps and has
a default duration of one hour.
2-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Table 2-14 Conferencing Entities (Continued)
Entity
Description
Name: Factory Video Profile
A Conference Profile is assigned to a Meeting Room to
define its conferencing parameters, such as line rate and
video resolution.
Conference
Profile
Factory Video Profile contains the video conference
parameters with a bit rate of 384Kbps, Auto Layout and
Polycom Skin. The Profile uses an IVR Service called
Conference IVR Service.
Conference IVR
Service
Name:
Conference IVR Service
The Conference IVR Service includes an optional video
slide and all the voice messages played during the
participant’s connection process and during the
conference.
The Conference IVR Service contains a set of voice
prompts in English and an optional video slide.
It automates the participant’s connection to a conference.
2-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
Table 2-14 Conferencing Entities (Continued)
Entity
Description
Entry Queue
Name
ID
DefaultEQ
1000
Using an Entry Queue enables one dial-in number to be
used for all conferences. In the Entry Queue, participants
are prompted for information to enable routing to their
destination conferences.
A default Entry Queue called DefaultEQ is provided.
The default Entry Queue is also set to Ad Hoc
conferencing which allows participants to start new
conferences without prior definition by entering a
Conference or Meeting Room ID that is not used by any
on going conference currently running on the MCU. It
uses an Entry Queue IVR Service called Entry Queue IVR
Service.
The default Welcome Slide displayed at the participants
endpoint upon connection to the Entry Queue and lists the
default Meeting Rooms. The participant can select one of
these Meeting Rooms or enter another ID to start a new
conference.
If no Transit Entry Queue is defined, DefaultEQ is the
default Transit Entry Queue. For more information see the
RMX 1500/2000/4000 Administrator’s Guide, ”Transit
Entry Queue” on page 4-9.
Note: An ISDN/PSTN dial-in number is not assigned to
the Entry Queue as the number depends on the dial-in
numbers range defined in the Network Service. It must be
manually assigned to enable ISDN or PSTN participant
connections to this Entry Queue. For more information,
see the RMX 1500/2000/4000 Administrator’s Guide,
”ISDN/PSTN Network Services” on page 13-46.
Entry Queue IVR
Service
Name:
Entry Queue IVR Service
Includes all the voice messages and video slides used to
guide participants though their connection process to the
MCU and route them to their destination conference.
Entry Queue IVR Service is the default Entry Queue IVR
Service provided for the default Entry Queue.
2-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Customizing the RMX’s Default Conferencing Settings
You can customize the conferencing entities to your organization’s
requirements:
•
•
•
To customize the Voice Prompts and Video Slides to different
organizations, users, languages etc. – first record the required
messages and create the video slides and then create the appropriate
conference IVR Service or Entry Queue IVR Service.
These services must be assigned to the appropriate conference profile
or Entry Queue. For more information, see the RMX 1500/2000/4000
Administrator’s Guide, ”IVR Services” on page 14-1.
To modify the conference properties, such as the conference line
rate, specific video layout for the conference or the background that is
used for the video display (skin), create a new Conference Profile.
This Profile can be used for defining new ongoing conferences,
Meeting Rooms and Single-dial Entry Queues.
For more information, see the RMX 1500/2000/4000 Administrator’s
Guide, ”Defining Profiles” on page 1-9.
To allow ISDN participants to connect to a single dial Entry Queue
a dial in number must be assigned to the pre-configured Entry
Queue.
To allow participants to connect to a single dial Entry Queue at a
line rate other than 384 Kbps (as in the default Entry Queue) or play
voice messages in different languages – create a new Entry Queue.
For more information, see the RMX 1500/2000/4000 Administrator’s
Guide, ”Defining a New Entry Queue IVR Service” on page 14-29.
•
You can personalize Meeting Rooms for people in your organization
with predefined conference and chairperson passwords (for added
security) and allow only authorized people to start on going
conferences. For more information, see the RMX 1500/2000/4000
Administrator’s Guide, ”Meeting Rooms” on page 3-1.
•
•
To allow ISDN participants to connect directly to Meeting Rooms a
dial in number must be assigned to the pre-configured Meeting
Room.
The conferencing entities are designed mainly for dial in participants
without prior definition of participants. You can create your own
Address Book containing a list of participants to be dialed by the
MCU. Once defined, these participants can be added to ongoing
conferences saving the need to define them again.
2-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2-First Time Installation and Configuration
For more information, see the RMX 1500/2000/4000 Administrator’s
Guide, ”Address Book” on page 5-1.
•
You can schedule conferences to start in the future.
2-46
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Basic Operation
The most common operations performed via the RMX Web Client are:
•
•
Starting, monitoring and managing conferences
Monitoring and managing participants and endpoints as
individuals or groups.
—
Participant – A person using an endpoint to connect to a
conference. When using a Room System, several participants use
a single endpoint.
—
Endpoint – A hardware device, or set of devices, that can call,
and be called by an MCU or another endpoint. For example, an
endpoint can be a phone, a camera and microphone connected
to a PC or an integrated Room System (conferencing system).
—
Group – A group of participants or endpoints with a common
name.
Starting the RMX Web Client
Before you begin you need to get the following information from your
system administrator:
•
•
•
User name
Password
MCU Control Unit IP Address
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
To start the RMX 2000 Web Client:
1
In your browser address line, enter
http://<Control Unit IP Address> and press the Enter key.
The Login screen is displayed.
Link to
RMX
Manager
Installer
2
Enter your Username and Password and click the Login button.
On first entry, the default Username and Password are both POLYCOM.
The RMX 2000 Web Client main screen is displayed.
The Login screen contains a link to the RMX Manager installer.
Using the RMX Manager application, a single user can control a single or
multiple RMX units as well as conferences from multiple RMXs. RMX 1500/
2000/4000 can be managed and controlled by the RMX Manager application.
For more information see the RMX 1500/2000/4000 Administrator’s Guide,
"RMX Manager Application” on page 17-1.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
RMX 2000 Web Client Screen Components
The RMX 2000 Web Client’s main screen consists of five panes:
•
•
•
•
•
•
Conference List
List Pane
RMX Management
Status Bar
Address Book
Conference Templates
You can login as a user with Chairperson, Operator or Administrator
authorization. Your Authorization Level determines your viewing and
system functions.
For more information see the RMX 1500/2000/4000 Administrator’s Guide,
"Users, Connections and Notes” on page 12-1.
The Administrator’s view is shown below:
Conferences
List
List
RMX
Management
Address
Book
Conference
Templates
Tab
Status
Bar
The main screen can be customized. For more information, see
"Customizing the Main Screen” on page 3-11.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Viewing and System Functionality Permissions
The RMX 2000 Web Client user’s viewing and system functionality depend
on the authorization level assigned to each user as summarized in
Table 3-1:
Table 3-1 Viewing and System Permissions
Authorization Level
Chairperson
Operator
Administrator
Viewing Permissions
Conference List
List Pane
Address Book
Conference Templates
Status Bar
RMX Management
Conference Alarms
Conference Status
Configurations
System Functionality
Start Conferences
Monitor Conferences
Monitor Participants
Solve Basic Problems
Modify MCU Configuration
In addition to Chairpersons, Operators and Administrators, an Auditor is a user
type that can view Auditor Files and audit the system. For more information see
the RMX 1500/2000/4000 Administrator’s Guide "Auditor” on page 18-101.
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Conferences List
If you are logged in as a user with Operator or Administrator
permissions:
The Conferences pane lists all the conferences currently running on the
MCU along with their Status, Conference ID, Start Time and End Time data.
The number of ongoing conferences is displayed in the pane’s title.
Save Conference
to Template
Start/Resume/Pause Recording
Stop Recording
Delete Conference
New Conference
Toolbar
List Headers
Conference Data
The Conferences list toolbar contains the following buttons:
•
•
New Conference – to start a new ongoing conference.
Delete Conference – delete the selected conference(s).
If Conference Recording is enabled the following are displayed in color:
—
—
—
Start/Resume Recording – start/resume recording.
Stop Recording – stop recording.
Pause –
toggles with the Start/Resume button.
If you are logged in as a user with Chairperson permissions:
•
you have entered the password or that don’t have a Chairperson
Password assigned.
•
A Chairperson Password field and a Refresh button are displayed.
The Refresh button does not change the Chairperson Password; it
resfreshes the Conferences list to display all ongoing conferences with
the requested password.
For more information see “Using the Chairperson Password for
Filtering” on page 3-49.
•
A Chairperson Password column is included in the conference data.
Chairperson Password Field
Refresh Button
Chairperson Password
Column
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
List Pane
The List pane displays details of the item selected in the Conferences pane
or RMX Management pane. The title of the pane changes according to the
selected item.
When selecting an ongoing conference in the Conferences pane, it displays
the list and parameters of the connected participants.
Total number of participants
When selecting an item in the Device Management pane, lists the items
currently defined for that item. For example, if Users is selected, it
displays the list of RMX Users defined for the selected RMX.
RMX Management
Viewing Permissions
The RMX Management pane lists the entities that need to be configured to
enable the RMX to run conferences. Only users with Administrators
permission can modify these parameters.
•
Frequently Used – parameters often configured monitored or
modified.
•
Rarely Used – parameters configured during initial system set-up
and rarely modified afterward.
Items can be moved between these two sections to customize the
management tasks per RMX User. For more details, see "Customizing the
RMX Management Pane” on page 3-12.
Status Bar
The Status Bar at the bottom of the RMX Web Client contains System and
Participant Alerts tabs as well as Port Usage Gauges and an MCU State
indicator.
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Viewing Permissions
System Alerts
This is a list of system problems. The alert indicator flashes red when at
least one system alert is active. The flashing continues until a user with
Operator or Administrator permission reviews the list.
The System Alerts pane is opened and closed by clicking the System Alerts
button in the left corner of the Status Bar.
Active
Alarms
Faults
List
For more information about Active Alarms and Faults List, see the RMX
1500/2000/4000 Administrator’s Guide, "System and Participant Alerts” on
page 18-1.
Viewing Permissions
Participant Alerts
This is a list of participants that are experiencing connection problems. It
is sorted by conference.
The Participant Alerts pane is opened and closed by clicking the
Participant Alerts button in the left corner of the Status Bar.
Viewing Permissions
Port Usage Gauges
The Port Usage gauges indicate:
•
The total number of Video or Voice ports in the system according to
the Video/Voice Port Configuration.
•
The number of Video and Voice ports in use.
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
•
The High Port Usage threshold.
Total Allocated Video Ports (CIF resolution) In System
Video Ports In Use
Video Port Usage Indicator
Total Allocated Audio Ports In System
Audio Ports In Use
Audio Port Usage Indicator
Audio and Video High Port Usage Threshold
The High Port Usage threshold represents a percentage of the total
number of video or voice ports available. It is set to indicate when
resource usage is approaching its maximum, resulting in no free resources
to run additional conferences. When port usage reaches or exceeds the
threshold, the red area of the gauge flashes and a System Alert is
generated. The default port usage threshold is 80% and it can be modified
by the system administrator. For more information, see the RMX 1500/
2000/4000 Administrator’s Guide, "Port Usage” on page 18-62.
Viewing Permissions
MCU State
The MCU State indicator displays one of the following:
•
– The MCU is starting up. The time remaining until
the system start-up is complete is displayed between brackets while a
green progress indicator bar indicates the start-up progress.
Progress Indicator Bar
Time Remaining
•
•
– The MCU is functioning normally.
– The MCU has a major problem. MCU behavior
could be affected and attention is required.
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Address Book
The Address Book is a list of Participants and Groups that have been defined
on the RMX. The information in the Address Book can be modified only by
an administrator. All RMX users can, however, view and use the Address
Book to assign participants to conferences.
Viewing Permissions
The Address Book toolbar contains a Quick Search field and the following
six buttons:
•
•
•
New Participant
•
•
•
New Group
Delete Participant
Import Address Book
Delete Group
Export Address Book
New Group
Delete Participant
New Participant
Delete Group
Import Address Book
Export Address Book
Click
to hide
Address
Book
Audio Participant
Video Participant
Group
Quick
Search
Address Book entries are listed according to:
•
•
•
•
Type – whether an individual Participant or a Group of participants
Name – of the participant or group
Dialing Direction – Dial-in or Dial-out
IP Address/Phone – of the participant
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Displaying and Hiding the Address Book
The first time you access the RMX Web Client, the Address Book pane is
displayed. You can hide it by clicking the anchor pin ( ) button.
The Address Book pane closes and a tab appears at the right edge of the
screen.
Click the tab to re-open the Address Book.
Click tab to open Address Book
Conference Templates
Conference Templates enable administrators and operators to create, save,
schedule and activate identical conferences.
A Conference Template:
•
•
Saves the conference Profile.
Saves all participant parameters including their Personal Layout and
Video Forcing settings.
•
Simplifies the setting up Telepresence conferences where precise
participant layout and video forcing settings are crucial.
Displaying and Hiding Conference Templates
The Conference Templates list pane is initially displayed as a closed tab in
the RMX Web Client main window. The number of saved Conference
Templates is indicated on the tab.
Conference Templates Tab
Number of Saved Conference Templates
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Clicking the tab opens the Conference Templates list pane.
Delete Template
New Template
Start Template
Click to hide the
Conference Templates List
Schedule Template
List of
Saved
Templates
Number of Saved Conference Templates
Hide the Conference Templates list pane by clicking the anchor pin (
)
button in the top right corner of the pane.
The Conference Templates list pane closes and a tab appears in the top right
corner of the screen.
Customizing the Main Screen
You can customize the main screen according to your preferences. Pane
sizes can be changed, column widths can be adjusted and data lists can be
sorted.
Customization settings are automatically saved for each logged-in user.
The next time the RMX Web Client is opened, the main screen settings appear
as they were when the user exited the application.
To re-size a pane:
Move the pointer over the pane border and when the pointer
becomes a click and drag the pane border to the required size and
release the mouse button.
To adjust column width:
1
In the column header row, place the pointer on the vertical field-
separator bar of the column.
2
When the pointer becomes a , click and drag the field separator bar
to the required column size and release the mouse button.
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
To sort the data by any field (column heading):
1
In the Conference list or List view pane, click on the column heading of
the field to be used for sorting.
A
or
symbol appears in the column heading indicating that the
list is sorted by this field, as well as the sort order.
2
Click on the column heading to toggle the column’s sort order.
To change the order of columns in a pane:
Click the column heading to be moved and drag it to its new position.
When a set of red arrows appears indicating the column’s new
position, release the mouse button.
To restore the RMX 2000 display window to its default configuration:
On the RMX 2000 menu, click View > Restore RMX Display
Defaults.
Customizing the RMX Management Pane
The RMX Management pane can be viewed either as a list or as a toolbar.
To switch between Toolbar and List Views:
In the RMX Management pane, click the Toolbar View button to switch
to Toolbar view.
In the RMX Management pane, click the Toolbar View button to switch
to Toolbar view.In Toolbar view, click the List View button to switch
back to List view.
3-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Toolbar View Button
List View
List View Button
Toolbar View
You can move items between the Frequently Used and Rarely Used sections
depending on the operations you most commonly perform and the way
you prefer to work with the RXM Web Client.
This only works in List view because in Toolbar view, all items are
represented by icons.
To expand or Collapse the Frequently Used and Rarely Used sections:
The Frequently Used and Rarely Used sections can be expanded or collapsed
by clicking the
and
buttons.
To move items within and between the Frequently Used and Rarely
Used sections:
1
In the RMX Management pane click and drag the icon of the item that
you wish to move.
An indicator line (
of the icon.
) appears indicating the new position
2
Release the mouse button when the icon is in the desired position.
The new position of the
Networks icon
List
View
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
The Frequently Used and Rarely Used sections can be expanded or collapsed
by clicking the and buttons.
3-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting a Conference
There are several ways to start a conference:
•
Clicking the New Conference button in the Conferences pane. For more
information, see "Starting a Conference from the Conferences Pane” on
page 3-16.
•
Dialing in to a Meeting Room.
—
A Meeting Room is a conference that is saved on the MCU. It
remains in passive mode until it is activated by the first
participant, or the meeting organizer, dialing in.
For more information about Meeting Rooms, see the RMX 1500/2000/
4000 Administrator’s Guide, "Meeting Rooms” on page 3-1.
•
•
Dialing in to an Ad Hoc Entry Queue which is used as the access
point to the MCU.
1500/2000/4000 Administrator’s Guide, "Entry Queues” on page 4-1.
Start a Reservation:
becomes ongoing immediately.
—
If the Start Time of the Reservation is in the future the conference
becomes ongoing, at the specified time on the specified date.
For more information, see "Starting a Reservation” on page 3-27.
•
Start any Conference Template saved in the Conference Templates list.
For more information, see "Starting an Ongoing Conference From a
Template” on page 3-29.
•
•
Clicking on the link included in a Microsoft Outlook Polycom Meeting
Invitation or by manually dialing the numbers displayed in the
invitation using the endpoint's numeric input device.
Attendees that have received an invitation to a Polycom Meeting via
the Polycom Conferencing Add-in for Microsoft Outlook can start a
conference by being the first invited attendee to click on a link in the
Meeting Invitation displayed on his/her workstation or calendaring
enabled endpoint, or manually dial in to the meeting using the
Polycom Conference information included in the Meeting Invitation.
For more information see the RMX 1500/2000/4000 Administrator’s
Guide, "Polycom Conferencing for Microsoft Outlook®” on page 9-1.
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Starting a Conference from the Conferences Pane
To start a conference from the Conference pane:
1
In the Conferences pane, click the New Conference ( ) button.
The New Conference – General dialog box opens.
The system displays the conference’s default Name, Duration and the
default Profile, which contains the conference parameters and media
settings.
The RMX automatically allocates the conference ID, when the
conference starts.
In most cases, the default conference ID can be used and you can just
click OK to launch the conference. If required, you can enter a
conference ID before clicking OK to launch the conference.
If you are the meeting chairperson or organizer using the RMX Web
Client to start your own meeting, you need to communicate the
default conference ID (or the one you created) to the other conference
participants so they can dial in.
You can use the New Conference - General dialog box to modify the
conference parameters. If no defined participants are to be added to
the conference, or you do not want to add additional information,
click OK.
3-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
General Tab
2
Define the following parameters:
Table 3-2 New Conference – General Options
Field
Description
Display Name
The Display Name is the conferencing entity name
in native language character sets to be displayed in
the RMX Web Client.
In conferences, Meeting Rooms, Entry Queues and
SIP factories the system automatically generates an
ASCII name for the Display Name field that can be
modified using Unicode encoding.
•
English text uses ASCII encoding and can
contain the most characters (length varies
according to the field).
•
•
European and Latin text length is approximately
half the length of the maximum.
Asian text length is approximately one third of
the length of the maximum.•
The maximum length of text fields also varies
according to the mixture of character sets (Unicode
and ASCII).
Maximum field length in ASCII is 80 characters. If
the same name is already used by another
conference, Meeting Room or Entry Queue, the
RMX displays an error message requesting you to
enter a different name.
Note: This field is displayed in all tabs.
Duration
Define the duration of the conference in hours using
the format HH:MM (default 01:00).
Note: This field is displayed in all tabs.
Permanent
Conference
Check this box to make this conference a
Permanent Conference: an ongoing conference with
no pre-determined End Time continuing until it is
terminated by an administrator, operator or
chairperson. For more information see the
RMX 1500/2000/4000 Administrator’s Guide
"Permanent Conference” on page 2-73.
Note: This field is displayed in all tabs.
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Table 3-2 New Conference – General Options (Continued)
Field
Description
Routing Name
Routing Name is the name with which ongoing
conferences, Meeting Rooms, Entry Queues and
SIP Factories register with various devices on the
network such as gatekeepers and SIP server. This
name must defined using ASCII characters.
Comma, colon and semicolon characters cannot
be used in the Routing Name.
The Routing Name can be defined by the user or
automatically generated by the system if no Routing
Name is entered as follows:
•
If ASCII characters are entered as the Display
Name, it is used also as the Routing Name
•
If a combination of Unicode and ASCII
characters (or full Unicode text) is entered as the
Display Name, the ID (such as Conference ID) is
used as the Routing Name.
If the same name is already used by another
conference, Meeting Room or Entry Queue, the
RMX displays an error message and requests that
you to enter a different name.
Profile
The system displays the name of the default
Conference Profile. Select the required Profile from
the list.
The Conference Profile includes the Conference line
rate, media settings and general settings.
For a detailed description of Conference Profiles,
see the RMX 1500/2000/4000 Administrator’s
Guide, "Conference Profiles” on page 1-1.
ID
Enter the unique-per-MCU conference ID. If left
blank, the MCU automatically assigns a number
once the conference is launched.
This ID must be communicated to conference
participants to enable them to dial in to the
conference.
3-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Table 3-2 New Conference – General Options (Continued)
Field
Description
Conference
Password
Enter a password to be used
by participants to access the
conference. If left blank, no
password is assigned to the
conference.
These fields are
numeric and have
a default length of
4 characters. The
administrator can
modify them in the
Setup - System
Configuration
settings. For more
information, see
RMX
Administrator’s
Guide, "System
Configuration” on
page 18-5.
This password is valid only in
conferences that are
configured to prompt for a
conference password.
Chairperson
Password
Enter a password to be used
by the RMX to identify the
Chairperson and grant him/her
additional privileges. If left
blank, no chairperson pass-
word is assigned to the confer-
ence.
This password is valid only in
conferences that are config-
ured to prompt for a chairper-
son password.
Reserve
Resources for
Video Participants
Enter the number of video participants for which the
system must reserve resources.
Default: 0 participants.
Maximum:
•
•
•
•
MPM Mode: 80 participants.
MPM+ Mode: 160 participants.
MPMx Mode: 180 participants (Double card)
MPMx Mode: 90 participants (Single card)
3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Table 3-2 New Conference – General Options (Continued)
Field
Description
Reserve
Resources for
Audio Participants
Enter the number of audio participants for which the
system must reserve resources.
Default: 0 participants.
Maximum:
•
•
MPM Mode: 80 participants.
MPM+ Mode: 200 participants (if all ports are set
to Audio Only).
•
•
MPMx Mode: 720 participants (Double card, with
all ports are set to Audio Only).
MPMx Mode: 360 participants (Single card, with
all ports are set to Audio Only).
Maximum Number
of Participants
Indicate the total number of participants that can be
connected to the conference. The automatic setting
indicates that the maximum number of participants
that can be connected to the MCU is determined
according to resource availability.
Note: If a number is specified, it should be large
enough to accommodate the participants specified in
the Reserve Resources for Video/Audio Participants
fields.
Enable ISDN/
PSTN Dial-in
Select this check box if you want ISDN and PSTN
participants to be able to connect directly to the
conference.
ISDN/PSTN
Network Service
The default Network Service is automatically
selected. A different ISDN/PSTN Network Service
can be selected from the Network Services list.
Dial-in Number (1)
Leave this field blank to let the system automatically
assign a number from the dial-in range defined for
the selected ISDN/PSTN Network Service. To
manually define a dial-in number, enter a unique
number from the dial-in number range defined for
the selected Network Service. This number cannot
be assigned to another Conference/Reservation/
Meeting Room/Gateway Profile
3-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Table 3-2 New Conference – General Options (Continued)
Field
Description
Dial-in Number (2)
By default, the second dial-in number is not defined.
To define a second-dial-in number, enter a required
number from the dial-in number range defined for
the selected Network Service.
3
4
If all participants are undefined, dial-in and no additional
information is required for the new conference, click OK.
To add participants from the Participants Address Book or to define
participants (mainly dial-out participants) click the Participants tab.
Participants Tab
This procedure is optional.
The Participants tab is used to add participants to the conference from the
Address Book.
It is also used to add defined dial-out participants to the conference. Defined
dial-out participants are connected to the conference automatically when the
conference is launched, unless the Dial Out Manually option is selected.
5
Click the Participants tab.
The Participants tab opens.
Participants
List
When defining a new conference, the Participants List is empty.
3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
The following table describes the information displayed in the
Participants List and the operations that can be performed.
Table 3-3 New Conference – Participants Tab
Column / Button
Description
Participants List
Name
A Unicode field that displays the participant’s name
and an icon representing the endpoint type: Audio
Only or Video.
IP Address/Phone Indicates the IP address or phone number of the
participant’s endpoint.
•
For dial-out connection, displays the IP
address or phone number of the endpoint
called by the Polycom RMX 1500/2000/4000.
•
For dial-in connection, displays the
participant’s IP address or phone number
used to identify and route the participant to
the appropriate conference.
Alias Name/SIP
Address (IP Only)
Displays the alias name of an H.323 endpoint or
the SIP URL.
Network
The network communication protocol used by the
endpoint to connect to the conference: H.323, SIP
or ISDN/PSTN.
Dialing Direction
Dial-in – The participant dials in to the
conference
Dial-out – The RMX dials out to the
participant
Encryption
Displays whether the endpoint uses encryption for
its media.
The default setting is Auto, indicating that the
endpoint must connect according to the
conference’s encryption setting.
Note: The H.320 protocol (ISDN/PSTN) does not
support encryption.
3-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Table 3-3 New Conference – Participants Tab (Continued)
Column / Button
Description
Buttons
New
Click to define a new participant.
For more information, see the RMX 1500/2000/
4000 Administrator’s Guide, "Adding a new
participant to the Address Book Directly” on
page 5-4.
Remove
Click to remove the selected participant from the
conference.
Add from Address
Book
Click to add a participant from the Address Book to
the conference.
Lecturer
Lecturer
This option is used to activate the Lecture Mode.
Select the participant you want to designate as
Lecturer from the list of conference participants.
The Lecturer can be selected once the conference
is running and participants are connected.
Dial Out Manually
Select this option to designate an RMX User-
controlled dial-out conference connection. When
checked, the user must connect each of the dial-
out participants who remain on standby until they
are connected to the conference.
Participants can be added to the conference in the following methods:
—
Defining a new participant during the definition of the
conference (clicking the New button).
—
Adding pre-defined participants from the Address Book by either
selecting the participants from the list or dragging and dropping
the participants from the Address Book to the Participants list.
—
Dial-in participants can connect to the conference after it was
started (without using the New Conference - Participants dialog
box).
3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
—
Once the conference has started, participants can be added to a
conference directly from the Participants Address Book without
having to use the New Conference – Participants tab. For more
details, see "Adding Participants from the Address Book” on
page 3-61.
To add participants from the Address Book:
6
In the Participants List, click the Add from Address Book button to
open the Participants Address Book.
7
In the Participants Address Book, select the participants that you want
to add to the conference and click the Add button.
Standard Windows multiple selection techniques can be used in this
procedure.
3-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
8
9
The selected participants are assigned to the conference and appear
in the Participant List.
Select additional Participants or click the Close button to return to the
Participants tab.
Information Tab
In the Info fields, you can add general information about the conference,
such as contact person name, company name, billing code, etc.
This information is written to the Call Detail Record (CDR) when the
conference is launched.
Changes made to this information once the conference is running are not
saved to the CDR.
This procedure is optional.
The information entered into these fields does not affect the conference.
To add information to the conference:
10 Click the Information tab.
The Information tab opens.
3-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
11 Enter the following information:
Table 3-4 New Conference – Info Options
Field
Description
Info1, 2, 3
There are three information fields that allow you to
enter general information for the conference such as
company name, contact person etc.
Unicode can be used in these fields.
The maximum length of each field is 80 characters.
Billing
Enter the conference billing code if applicable.
12 Click OK.
An entry for the new conference appears in the Conferences pane.
If no participants were defined for the conference or as long as no
participants are connected, the indication Empty and a warning icon
(
) appear in the Status column in the Conferences pane.
The status changes when participants connect to the conference.
If no participant connects within the time specified in the Conference
Profiles > Auto Terminate > Before First Joins field, the conference is
automatically terminated by the system.
3-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Starting a Reservation
To start a conference from the Reservation Calendar:
1
2
In the RMX Management pane, click the Reservations entry ( ).
The Reservation Calendar is displayed.
Click the New Reservation (
) button.
3-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
The New Reservation – General tab dialog box opens.
3
4
Optional. Select the Enable ISDN/PSTN Dial-in check box if you
want ISDN and PSTN participants to be able to connect directly to the
conference.
If Enable ISDN/PSTN Dial-in option is selected, either enter a dial-in
number, or leave the Dial-in Number field blank to let the system
automatically assign a number from the dial-in range defined for the
selected ISDN/PSTN Network Service.
5
Click the OK button.
A confirmation box is displayed stating that the Reservation time is
past due and that the conference will become ongoing.
6
Click OK.
3-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
The conference is started. If an ISDN/PSTN dial-in number was assigned
to the conference either automatically or manually, this number can be
viewed in the Conferences pane.
For more information about Reservations, see the RMX 1500/2000/4000
Administrator’s Guide, "Reservations” on page 6-1.
Starting an Ongoing Conference From a Template
An ongoing conference can be started from any Conference Template
saved in the Conference Templates list.
To start an ongoing conference from a Template:
1
In the Conference Templates list, select the Template you want to start
as an ongoing conference.
2
Click the Start Conference from Template ( ) button.
or
Right-click and select Start Conference from Template.
The conference is started.
If a Conference Template is assigned a dial-in number that is already assigned
to an ongoing conference, Meeting Room, Entry Queue or Gateway Profile,
when the template is used to start an ongoing conference or schedule a
reservation it will not start. However, the same number can be assigned to
several conference templates provided they are not used to start an ongoing
conference at the same time. If a dial in number conflict occurs prior to the
conference’s start time, an alert appears: “ISDN dial-in number is already
assigned to another conferencing entity” and the conference cannot start.
The name of the ongoing conference in the Conferences list is taken
from the Conference Template Display Name.
3-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Participants that are connected to other ongoing conferences when
the template becomes an ongoing conference are not connected.
If an ongoing conference, Meeting Room or Entry Queue with the same Display
Name, Routing Name or ID already exist in the system, the conference will not
be started.
For detailed description of Conference Templates, see RMX 1500/2000/
4000 Administrator’s Guide, "Conference Templates” on page 8-1.
3-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Starting a Video Meeting from a Microsoft Outlook Polycom
Meeting Invitation
Polycom Conference information is included in the meeting invitation sent
by Outlook to each meeting attendee. The following example shows a
Polycom Conference invitation as received by Outlook running on a
workstation.
Click Link to
Connect
Dial Manually
to Connect
If the attendee is the first to connect to the meeting, he/she starts the
meeting by clicking on the link included in the invitation or by manually
dialing the numbers displayed using the endpoint's numeric input device.
For more information see the RMX 1500/2000/4000 Administrator’s Guide,
"Polycom Conferencing for Microsoft Outlook®” on page 9-1.
3-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Connecting to a Conference
Direct Dial-in
Direct dial-in connection to conferences and Meeting Rooms is available
to all endpoints.
Participants must be provided with a dialing string which can vary
according to the network type, conference password and chairperson
password.
Participants dial the conference dial-in string and are connected to the
conference IVR Service. Once the correct information, such as the
conference password and chairperson password are entered, the
participants are connected to the conference.
Figure 3-1 Dial-in Connection via IVR System
The MCU can be configured to enable the chairperson to use the
chairperson password as the conference password without the need to
enter the conference password.
3-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
H.323 Participants
For H.323 participants, the dialing string is composed of the MCU prefix
in the Gatekeeper and the conference ID.
Example:
Prefix in gatekeeper
Conference ID
925
1001
Conference Name
Maple_Room
The participant dials 9251001or 925Maple_room
If there is no gatekeeper defined for the network, H.323 participants dial
the MCU’s signaling host IP address and the conference ID, separated
by ##.
Example:
MCU (Signaling Host) IP address
Conference ID
172.22.30.40
1001
The participant dials 172.22.30.40##1001
SIP Participants
For SIP participants the dialing string is composed of the conference
routing name and domain name in the following format:
conference_routing_name@domain_name
Example:
Conference routing name
1001
The participant dials 1001@polycom.com
ISDN/PSTN Participants
Dial-in ISDN and PSTN participants dial one of the dial-in numbers
assigned to the conference/Meeting Room/Reservation/Conference
Template, including the country and area code (if needed). They are
routed to their conference according to the dial-in number.
Example:
Assigned dial-in number
The participant dials
4631111
4631111
3-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Connecting to a Polycom Conference from an Outlook
Meeting Invitation
Attendees that have received a Meeting Invitation via Outlook using the
Polycom Conferencing Add-in for Microsoft Outlook, connect by clicking on
the link included in the invitation or by manually dialing the numbers
displayed using the endpoint's numeric input device.
Click Link to
Connect
Dial Manually
to Connect
For more information see the RMX 1500/2000/4000 Administrator’s Guide,
"Polycom Conferencing for Microsoft Outlook®” on page 9-1.
3-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Entry Queue Access
Access via an Entry Queue allows all participants to dial the same entry
point that acts as a routing lobby. Once in the Entry Queue, participants
are guided to the conference according to the conference ID they enter.
Figure 3-2 Dial-in Connection via Entry Queue
H.323 Participants
Dialing is executed in the same way as for conferences, where the Entry
Queue ID/Name replaces the Conference ID/Name.
H.323 participants dial [Gatekeeper Prefix][Entry Queue ID/Name].
Example:
Prefix in gatekeeper
Entry Queue ID
925
1000
The participant dials 9251000
3-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
H.323 participants can bypass the Entry Queue IVR voice messages by
adding the correct Conference ID of destination conference to the initial
dial string:
[Gatekeeper Prefix][EQ ID][##Destination Conference ID]
Example:
Conference ID
1001
H.323 participants dial 9251000##1001
H.323 participants can also bypass the conference IVR voice messages by
adding the Conference Password to the initial dial string:
[Gatekeeper Prefix][EQ ID][##Destination Conference
ID][##Password]
Example:
Conference ID
1001
Conference Password
34567
H.323 participants dial 9251000##1001##34567
SIP Participants
Using an Entry Queue minimizes the number of conferences that require
registration with the SIP server and enables using one URI address for all
dial-in connections, using the format:
<Entry Queue routing name>@<domain name>
Example:
Entry Queue Routing Name
Domain Name
DefaultEQ
polycom.com
SIP participants dial DefaultEQ@polycom.com
ISDN and PSTN Participants
Up to two dial-in numbers can be allocated to an Entry Queue for use by
ISDN and PSTN participants.
Calls to numbers within the ISDN and PSTN Dial-in Range that are not
allocated to an Entry Queue are routed to the Transit Entry Queue.
Dial-in ISDN and PSTN participants dial one of the dial-in numbers
assigned to the Entry Queue, including the country and area code (if
needed).
They are routed to their conference according to the conference ID.
3-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Example:
Entry Queue ID
Assigned Dial-in number
1000
4631000
ISDN/PSTN participants dial 4631000
Dial-out Participants
Automatic Dial Out
Dial-out participants are defined with their dial-out number. Once they
are added to the ongoing conference, the MCU automatically calls them at
a rate of 1 dial-out per second, using the default H.323, SIP or ISDN/
PSTN Network Service defined for them.
Manual Dial Out
In the manual mode, the RMX user or meeting organizer instructs the
conferencing system to call the participant. Dial-out participants must be
defined (mainly their name and telephone number) and added to the
conference. This mode can only be selected at the conference definition
stage and cannot be changed once the conference is running.
Gathering Phase
The Gathering Phase of a conference is the time period during which
participants are connecting to a conference. It is enabled for the
conference in the Conference Profile - Gathering Settings dialog box.
During the Gathering Phase, a mix of live video from connected endpoints
is combined with both static and variable textual information about the
conference into a slide which is displayed on all connected endpoints. All
connected participants are kept informed about the current conference
status including names of connected participants, participant count,
participant type (video/audio) etc.
3-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
During the Gathering Phase, the audio of all participants can be heard, and
the video of active speakers is displayed in the video windows as they
begin talking.
Live Video From Connected Participants
Textual Information
Recording
Indicator
Optional Additional
Information
Participant
Count
Connected
Participants
(If enabled)
Conference
Information
Access
Numbers
3-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Gathering Phase Guidelines
•
The Gathering Phase slide can be displayed at any time during the
conference by entering the Show Participants DTMF code, *88.
•
•
The Gathering Phase is not supported in Video Switching Conferences.
The names of the first eight participants to connect are displayed. If
eight or more participants connect, the 8th row displays “…”.
•
Static text in the Gathering Phase slide such as the field headings:
Organizer, Duration, Video/Audio Participants, Access Number, IP are
always displayed in the language as configured in the Polycom Virtual
Meeting Rooms Add-in for Microsoft Outlook. The following languages
are supported:
- English
- Korean
- French
- Japanese
- German
- Simplified Chinese
- International Spanish
•
•
Dynamic text in the Gathering Phase slide such as the meeting name,
participants names, access numbers and the additional information
entered in the Info1/2/3 fields of the Gathering Settings tab of the
conference Profile are displayed in the language of the meeting
invitation.
The language of a Gathering Phase slide of a conference configured to
include a Gathering Phase that is not launched by the Polycom
Conferencing Add-in for Microsoft Outlook is configured by the
administrator. Using the RMX Web Client, the administrator selects
the language for the Gathering Phase slide. The language selected can
be different to that of the RMX Web Client used by the administrator
to perform the configuration.
•
Content can be sent during the Gathering Phase. The content is
displayed in the large video window of the participant’s layout while
3-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
the Gathering slide is displayed in a smaller video window in the
layout.
Content
Gathering Slide
For more information see, the RMX 1500/2000/4000 Administrator’s Guide,
"Gathering Phase” on page 2-33.
3-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Text Indication in the Video Layout
Endpoint Names
During conferences you can view the names of the endpoints that are
connected to the conference in your endpoint’s video layout windows.
The MCU can display up to 33 characters of the endpoint’s name,
depending on the window’s layout (size).
The following is an example of endpoint name display in the endpoint
screen:
Endpoint names (in
Unicode or ASCII)
in 2 x 2 video layout
Saturn Room
Tarney
Adam
Orion Room
The displayed name is determined as follows:
•
•
The system displays the name that is defined at the endpoint.
If the endpoint does not send its name:
—
For a defined H.323 or SIP participant:
•
The system displays the name from the participant
definition.
—
For an undefined H.323 participant:
•
Display the H.323 ID alias.
or
Display the E.164 alias.
or
Display nothing if all the fields are empty.
3-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
—
For a SIP undefined participant:
•
Display the SIP DisplayName field.
or
Display the SIP Address (SIP application server).
or
Display the SIP ContactDisplay field.
or
Display nothing if all the fields are empty.
—
—
For a defined H.320 participant:
•
The system displays the name from the participant
definition.
For an undefined H.320 participant:
•
Display the Terminal Command String (TCS-2) to identify the
participant.
or
Display nothing if the string is not received or empty.
•
If the endpoint’s Display Name is changed in the RMX Web Client, it
overrides all the above.
To change the Display Name:
1
In the Participants list, double-click the participant or right-click the
participant and then select Participant Properties.
3-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
The Participant Properties – Media Sources dialog box opens:
2
3
Enter the new Display Name in the Name field.
Click OK.
3-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Text Indication
The Text Indication appears in the window of the current speaker in the
participant’s layout in addition to the endpoint name. It displays the
conference Secure mode (on or off), total number of connected
participants, number of video participants and number of audio
participants.
The text indication is automatically displayed when there is a change in
the conference Secure state (when Secure is implemented or cancelled)
and it appears only for a few seconds (the same duration as the endpoint
names).
The conference chairperson or participants can request the display of a
Textual Indication of the conference’s statistics by entering the DTMF code
*88 on the endpoint’s DTMF input device, such as remote control.
Text Indicator
Participant’s Layout
Current Speaker
Endpoint Name
The Text Indication is displayed according to the permission set in the
Conference IVR Service:
•
•
Chairperson permission: Only the chairperson sees the indication
Everyone permission: All participants see the indication.
Participants connected as Secondary (no video) will be considered as audio
participants; defined participant which are not currently connected to the
conference (disconnected, redial, disconnecting, etc.) are not counted.
Text Indication can be disabled by adding a new flag to the System
Configuration and setting its value to NO as follows
:
ENABLE_TEXTUAL_CONFERENCE_STATUS=NO.
3-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
This setting is recommended for MCUs running Telepresence conferences.
For more information, see the RMX 1500/2000/4000 Administrator’s Guide,
“System Configuration” on page 18-5.
Transparent Endpoint Names
Endpoint name backgrounds are 50% transparent, and while maintaining
contrast, do not completely obscure the overlaid video.
The Endpoint Name Transparency feature can be disabled by adding a new
flag to the System Configuration and setting its value to NO as follows
:
SITE_NAME_TRANSPARENCY=NO.
For more information, see the RMX 1500/2000/4000 Administrator’s Guide,
“System Configuration” on page 18-5.
Permanent Display of Endpoint Names
Endpoint Names can be permanently displayed by adding a new flag to the
System Configuration and setting its value to YES as follows
:
SITE_NAMES_ALWAYS_ON =YES.
For more information, see the RMX 1500/2000/4000 Administrator’s Guide,
“System Configuration” on page 18-5.
Closed Caption
When enabled, IP endpoints that support FECC (Far End Camera
Control) can also be configured to provide real-time text transcriptions or
language translations of the video conference by displaying closed
captions.
The captions for a conference may be provided by the captioner who is
present in the conference, or the captioner may use a telephone or web
browser to listen to the conference audio.
When the captioner sends a unit of text, all conference participants see it
on the main monitor for 15 seconds. The text then disappears
automatically.
Endpoint Name display is not affected by Closed Captions display.
For more information, see the RMX 1500/2000/4000 Administrator’s Guide,
"Closed Captions” on page 2-44.
Closed Captions option is enabled by a system flag in the system
configuration. For more details about system flags, see the RMX 1500/
2000/4000 Administrator’s Guide, "System Configuration” on page 18-5.
3-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Message Overlay
Message Overlay allows messages to be sent to all participants in an
ongoing conference.
A maximum of 24 Unicode characters can be sent as a Message Overlay.
The message can be set to be displayed at various positions on the screen
in different colors, static or scrolling.
Small Text, White on red, Top, Middle
Small Text, White on yellow, Bottom
For more information see the RMX 1500/2000/4000 Administrator’s Guide
"Message Overlay” on page 2-46.
3-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Monitoring Ongoing Conferences
Conference monitoring enables you to keep track of conferences and their
participants: if all its participants are correctly connected and whether
errors or faults have occurred.
Maximum number of participants (voice and video) in a conference:
RMX 1500 MPMx Mode: 360. (90 video).
RMX 2000 MPM Mode: 400. (80 video).
RMX 2000 MPM+ Mode: 800. (160 video).
RMX 2000 MPMx Mode: 720. (180 video).
RMX 4000 MPM+ Mode: 1600. (160 video).
RMX 4000 MPMx Mode: 1440. (180 video).
General Monitoring
All monitoring and operations procedures performed during ongoing
conferences can be performed by either of two methods:
•
Using the buttons in the toolbars.
Toolbar Buttons
Tooltip appears when cursor is positioned over button
3-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
•
Right-clicking anywhere in the Conferences or Participants pane and
selecting an operation from the menu.
Operations
Menu
Multi Selection
Using multiple selection, you can monitor and perform simultaneous
operations on multiple participants in multiple conferences.
The selected conferences are displayed as sub-lists in the Participants list
pane.
The sub-lists can be expanded and collapsed by clicking the
and
sublist control buttons that appear next to the conference name in the
sublist headings.
Participant Sublists
Multi-selected
Conferences
Control button in
sublist header
3-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Using the Chairperson Password for Filtering
If you are logged in as a chairperson, the Chairperson Password field is
displayed. It enables you to search for, and display a list of, ongoing
conferences for which you have the password.
Chairperson Password Field
Refresh Button
Chairperson Password Column
To search for an ongoing conference by Chairperson Password:
1
2
3
Click in the Chairperson Password field.
Enter the password to be searched for.
Click the Refresh button.
The Conferences list is refreshed and ongoing conferences with the
requested password are displayed.
Conference Level Monitoring
Conference level monitoring is available to the administrator, operator
and chairperson.
The Conference List pane displays information about ongoing conferences.
Status
One or more of the status indicators listed in Table 3-5 may appear in the
Status column.
3-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
No status indicator display in the Status column means that the
conference is running without problems.
One or more of the status indicators listed in Table 3-5 may appear in the
Status column.
Table 3-5 Conferences – Monitoring Information
Field
Description
Name
Displays conference name and type of conference:
•
– Video Conference (including HD CP
conferences).
•
•
– Conference running in Video Switching mode.
– The conference has been secured using the *71
DTMF code. For details, see "Secured Conference
Monitoring” on page 3-53.
•
– Operator Conference.
3-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Table 3-5 Conferences – Monitoring Information (Continued)
Field
Description
Status
Displays the status of the ongoing conference.
If there is no problem with the participant’s connection no
indication is displayed.
If one of the following statuses occur, the appropriate
indication is displayed, proceeded by a warning icon ( ).
•
Audio – There is a problem with the participant’s
audio.
•
•
Empty – No participants are connected.
Faulty Connection – Participants are connected, but
the connection is problematic.
•
•
Not Full – Not all the defined participants are
connected.
Partially Connected – The connection process is not
yet complete; the video channel has not been
connected.
•
•
•
•
Single Participant – Only one participant is
connected.
Video – There is a problem with the participant’s
video.
Content Resource Deficiency – Content will not be
sent to legacy endpoints.
Awaiting Operator – A participant has requested
operator assistance.
ID
The Conference ID assigned to the conference.
Conference start time.
Start Time
End Time
Dial in Number(1)
The time the conference is expected to end.
The Conference dial in number for ISDN/PSTN
participants.
Additional information about the conference can be viewed when
accessing the conference properties.
3-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
To monitor a conference:
In the Conference List pane, double click the name of the conference
you wish to monitor, or right-click the conference and then click
Conference Properties.
The Conference Properties - General dialog box opens.
You can view all the conference’s properties but those that appear
with a gray background cannot be modified.
For more information, see the RMX 1500/2000/4000 Administrator’s
Guide, "Conference Level Monitoring” on page 10-3.
Roll Call/Audible Tones During an Ongoing
Conference
If Roll Call is enabled, when a participant joins or leaves a conference, the
system plays a voice message to all participants. The audio message
consists of the joining or leaving participant’s Roll Call name followed by
either “has joined the conference” or “has left the conference”.
3-52
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
These voice messages can be replaced with audio tones. The use of tones
requires that the appropriate tone files in *.wav format be uploaded and
configured to replace the Roll Call Joined and Roll Call Left message files.
This feature is enabled or disabled by value of the
IVR_ROLL_CALL_USE_TONES_INSTEAD_OF_VOICE System Flag in
system.cfg:
•
•
When set to NO (default), voice messages are played.
When set to YES, the uploaded tones replace the voice messages.
For more information see the RMX 1500/2000/4000 Administrator’s Guide,
"Modifying System Flags” on page 18-5 and "Defining a New Conference IVR
Service” on page 14-9.
Audio Only Message
H.323 and SIP video participants that are connected as Secondary (Audio
Only) because of lack of video resources receive an audio message: “All
video resources are currently in use. Connecting using audio only” indicating
why their video has not connected. For more information see the
RMX 1500/2000/4000 Administrator’s Guide.
Secured Conference Monitoring
When Secured Conference Mode is enabled on the RMX, it locks the
conference and prevents participants and RMX Users from joining the
conference. A Secured conference cannot be monitored or controlled in
any way. While a conference is in the Secure Mode, the RMX User with
Administrator authorization cannot view the participants list or any other
conference properties, but can manually terminate it.
The conference chairperson can enable or disable the Secure mode from
the DTMF input device (touch-tone telephone or the endpoint’s remote
control), using the appropriate DTMF code (the default code is *71).
During the secure conference, the chairperson and participants can
perform various operations, such as muting, via their DTMF input device
using the appropriate DTMF codes. However, because Secure conferences
cannot be monitored, these operations or status changes are not displayed
in the Conferences or Participants panes.
A special icon is used to indicate that the conference is in Secure mode.
3-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Monitoring Ongoing Gateway Sessions
Ongoing Gateway Sessions that are created when calling the Gateway
Profile, are listed in the ongoing Conferences list pane and are monitored
in the same way as the conferences.
For more details, see the RMX 1500/2000/4000 Administrator’s Guide,
"Conference Level Monitoring” on page 10-3.
Participant Level Monitoring
Participant Connection Monitoring
When a conference is selected in the Conference List, details of its
participants appear in the List pane.
The following participant indicators and properties are displayed:
Table 3-6 Participant Monitoring – Indicators and Properties
Column
Icon/Description
Name
Displays the name and type (icon) of the participant:
Audio Participant – Connected via IP phone or
ISDN/PSTN.
Video Participant – Connected with audio and video
channels.
3-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Table 3-6 Participant Monitoring – Indicators and Properties (Continued)
Column
Icon/Description
Status
Displays the connection status (text and icon) of the
participant. If there is no problem with the participant’s
connection no indication is displayed.
Connected – The participant is successfully
connected to the conference.
Disconnected – The participant is disconnected from
the conference. This status applies only to defined
participants.
Waiting for Dial-in – The system is waiting for the
defined participant to dial into the conference.
Partially Connected – The connection process is not
yet complete; the video channel has not been
connected.
Faulty Connection – The participant is connected,
but problems occurred in the connection, such as
synchronization loss.
Secondary Connection – The endpoint’s video
channel cannot be connected to the conference and
the participant is connected only via audio.
Awaiting Individual Assistance – The participant
has requested the user’s (operator’s) assistance.
Awaiting Conference Assistance – The participant
has requested the operator’s assistance for the
conference. This usually means that the user
(operator) has been requested to join the conference.
3-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Table 3-6 Participant Monitoring – Indicators and Properties (Continued)
Column
Icon/Description
Role
Displays the participant’s role or function in the conference:
Chairperson – The participant is defined as the
conference chairperson. The chairperson can
manage the conference using touch-tone signals
(DTMF codes).
Lecturer – The participant is defined as the
conference Lecturer.
Lecturer and Chairperson – The participant is
defined as both the conference Lecturer and
Chairperson.
Cascade Enabled Dial-out Participant – A special
participant functioning as a link in a cascaded
conference.
Recording – A special participant functioning as a
Recording Link.
IP Address/
Phone
The IP participant’s IP address or the ISDN/PSTN
participant’s phone number.
Alias Name/
SIP Address
The participant’s Alias Name or SIP URI.
The alias of an RSS 2000 Recording System if the
participant is functioning as a recording link.
Network
The participant’s network connection type – H.323, SIP or
ISDN/PSTN.
Dialing
Dial-in – The participant dialed the conference.
Direction
Dial-out – The MCU dialed the participant.
3-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Table 3-6 Participant Monitoring – Indicators and Properties (Continued)
Column
Icon/Description
Audio
Displays the status of the participant’s audio channel.
If the participant’s audio is connected and the channel is
neither muted nor blocked, no indication is displayed.
Disconnected – Participant’s audio channel is
disconnected. This is a defined participant who is
waiting to be connected to the conference.
Muted – Participant’s audio channel is muted. The
participant can still hear the conference.
Blocked – Transmission of audio from the
conference to the participant is blocked.
Muted and Blocked - Audio channel is muted and
blocked.
Video
Displays the status of the participant’s video channel.
If there is no problem with the participant’s video connection
and the channel is neither suspended nor secondary, no
indication is displayed.
Disconnected – Participant’s video channel is
disconnected. This is a defined participant who is
waiting to be connected to the conference.
Suspended – Video transmission from the endpoint
to the conference is suspended.
Secondary – Participant is connected only through
the audio channel due to problems with the video
channel.
Encryption
Indicates that the endpoint is using encryption for its
connection to the conference.
FECC Token
Participant is the holder of the FECC token and has
Far End Camera Control capabilities.
The FECC token can be allocated to only one
participant at a time and remains un-allocated if no
participant requests it.
3-57
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Table 3-6 Participant Monitoring – Indicators and Properties (Continued)
Column
Icon/Description
Participant is the holder of the Content token and has
Content Token
content sharing permission.
The Content token can be allocated to only one
participant at a time and remains un-allocated if no
participant requests it.
For more information, see the RMX 1500/2000/4000
Administrator’s Guide, "H.239” on page 2-22.
For more information, see the RMX 1500/2000/4000 Administrator’s Guide,
"Participant Level Monitoring” on page 10-15.
Video Preview
Video Preview enables the RMX users to monitor the quality of the video
sent and received by the participant and identify possible quality
degradation.
To preview the participant video:
1
2
List the conference participants in the Participants pane.
Right-click the participant whose video you want to preview and
then click one of the following options:
3-58
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
—
—
View Participant Sent Video - to display the video sent from the
participant to the conference.
View Participant Received Video - to display the video sent
from the conference to the participant.
The Video Preview window opens.
If the video card installed in the PC does not support DirectDraw Acceleration, a
black window may be viewed.
For more information, including workstation minimum requirements, see the
RMX 1500/2000/4000 Administrator’s Guide.
3-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Operations Performed During On Going
Conferences
Conference Level operations
Changing the Duration of a Conference
The duration of each conference is set when the new conference is created.
The default duration of a conference is 1 hour. All conferences running on
the RMX are automatically extended as long as there are participants
connected to the conference.
A conference’s Duration can be extended or shortened while it is running,
by modifying its scheduled End Time.
To extend or shorten a conference manually:
1
2
In the Conference List pane, double-click the conference Name.
In the General tab, modify the End Time fields and click OK
.
The End Time is changed and the Duration field is updated.
3-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
To terminate a conference manually:
1
In the Conferences list, select the conference you wish to delete and
click the Delete Conference ( ) button.
You are prompted for confirmation.
2
Click OK to terminate the conference.
Adding Participants from the Address Book
Once the conference has started, you can add participants to a conference
directly from the Participants Address Book without having to use the New
Conference – Participants tab.
To drag & drop participants into the Participants List:
1
2
Open the Address Book.
Select, drag and drop the participant that you wish to add to the
conference directly from the Participant Address Book into the
Participant List.
Standard Windows multiple selection techniques can be used in this
procedure.
3-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Moving Participants
RMX users can assist participants by performing the following operations:
•
•
•
Move a participant to an Operator conference (Attend a participant).
Move a participant to the Home (destination) conference.
Move participant from one ongoing conference to another
A move can be performed using the following methods:
•
•
Using the participant right-click menu
Using drag and drop
To move a participant from the ongoing conference using the right-click
menu options:
1
In the Conferences list, click the conference where there are
participants waiting for Operator’s Assistance to display the list of
participants.
2
In the Participants list, right-click the icon of the participant to move
and select one of the following options:
—
—
Move to Operator Conference - to move the participant to the
Operator conference
Move to Conference - to move the participant to any ongoing
conference.
3-62
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
When selected, the Move to Conference dialog box opens, letting
you select the name of the destination conference.
—
Back to Home Conference - if the participant was moved to
another conference or to the Operator conference, this options
moves the participant back to his/her source conference.
This option is not available if the participant was moved from
the Entry Queue to the Operator conference or the destination
conference.
Moving a Participant Interactively
You can drag and drop a participant from the Entry Queue or ongoing
conference to the Operator or destination (Home) conference:
1
Display the participants list of the Entry Queue or the source
conference by clicking its entry in the Conferences list.
2
In the Participants list, drag the icon of the participant to the
Conferences List pane and drop it on the Operator Conference icon or
another ongoing conference.
3-63
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Saving an Ongoing Conference as a Template
Any conference that is ongoing can be saved as a template.
To save an ongoing conference as a template:
1
In the Conferences List, select the conference you want to save as a
Template.
2
Click the Save Conference ( ) button.
or
Right-click and select Save Conference.
The conference is saved to a template whose name is taken from the
ongoing conference Display Name.
Copy and Paste Conference
The RMX user can Copy, and Paste conferences. When using the RMX
Web Client, conferences can copied and pasted on the same RMX, however
when using the RMX Manager, with its ability to manage multiple RMXs,
conferences can be copied and pasted between different RMXs.
Copy Conference
The Copy command copies all the conference’s properties including
connected participants and makes these properties available for pasting,
starting a new conference. The copied conference remains active until it
terminates or is deleted.
To copy a conference:
1
In the Conferences List pane, right-click the conference you want to
copy.
3-64
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
2
In the drop-down menu select Copy Conference.
Paste Conference
The Paste Conference command starts the new conference on the same
RMX or on a different RMX.
To paste a conference:
>> Right-click in the Conferences List pane and in the drop-down menu
select
Paste Conference.
or
If you are using the RMX Manager and you want to paste the
conference to a different RMX:
a
In the MCUs list pane, click the RMX that is to receive the
conference.
3-65
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
b
In the Conferences list pane, right-click, and in the drop-down
menu select Paste Conference.
The conference is pasted to the RMX with a Display Name is assigned
by the system.
Paste Conference As
The Paste Conference As command allows the RMX user to create a new
conference using the copied conference’s properties as a template. It
automatically opens the Conference Properties dialog box allowing the
RMX user to modify the General, Participants and Information tabs to create
the new conference. When the OK button in the Conference Properties
dialog box conference Properties dialog box is clicked the new conference is
started.
To paste a conference as a new conference:
1
Right-click in the Conferences List pane and in the drop-down menu
select
Paste Conference As.
or
If you are using the RMX Manager and you want to paste the
conference to a different RMX:
a
In the MCUs list pane, click the RMX that is to receive the
conference.
3-66
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
b
In the Conferences list pane, right-click, and in the drop-down
menu select Paste Conference As.
The Conference Properties dialog box is displayed.
2
3
Modify the conference information as required.
Click the OK button to paste and start the new conference.
Changing the Video Layout of a Conference
While the conference is running, you can change the video layout and
select one of 24 video layouts supported by the RMX.
Video Layout selection can be done in two levels:
3-67
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
•
•
Conference Level – Applies to all conference participants. All
participants have the same video layout.
Participant Level – The participant’s video layout is changed. All
other conference participants’ video layouts are not affected.
The initial video layout is selected for the conference in the Conference
Profile.
Participant level video layout selection overrides conference level video
layout settings.
To change the video layout of a conference:
1
In the Conference Properties dialog box, select Video Settings.
Video
Windows
Representation
Video
Layout
Options
Selected
Layout
2
If the Auto Layout check box is selected, clear it.
3-68
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
3
From the Video Layout options, select the Number of Windows to display
and the Video Layout thumbnail required and click OK
.
Number of
Video
Windows
Video
Layout
Thumbnail
Selected
Layout
Video Forcing
Users with Chairperson or Operator permission can select which
participant appears in each of the video layout windows using Video
Forcing. When a participant is forced to a layout window, switching
between participants is suspended for that window and only the assigned
participants is viewed. Video Forcing works on Conference Level or
Participant Level:
•
Conference Level – When forcing a participant to a window, all
conference participants will see that participant in the selected
window.
•
Participant Level – When forcing a participant to a window, only the
participant’s video layout display is affected. All other participants
see the conference layout.
Video Forcing Guidelines:
•
A participant cannot appear in two or more windows at the same
time.
3-69
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
•
•
•
Participant level video forcing overrides conference level video
forcing.
A participant can view him/herself in a layout window, by selecting
the Same Layout option.
When different size video windows are used in video layouts such as
1+2, 1+3, 1+4, etc., a participant can only be forced, in Personal Layout,
to a video window of the same size as that selected for him/her in
Conference Layout.
•
•
When changing the Video Layout at the conference level, the video
forcing settings are not applied to a new layout, and switching
between participants is audio-activated. The video forcing setting are
saved and applied the next time the layout is selected.
Windows that are not assigned any participant display the current
speaker and last speakers.
To video force a participant to a window:
1
2
3
4
In the Conference Properties dialog box, select the Video Settings tab.
If Auto Layout check box is selected, clear it.
Select the required video layout.
In the window to which you want to force a participant, select the
participant’s name from the list of conference participants.
List of
Conference
Participants
Selected
Layout
Video
Windows
3-70
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
5
6
Repeat step 3 to force participants to other windows.
Click OK.
To cancel Video Forcing for a window:
1
2
3
In the Conference Properties dialog box, select the Video Settings tab.
In the video layout window, in the Participants list, select Auto.
Click OK.
Switching between participants is renewed and is audio activated.
3-71
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Enabling and Disabling Video Clarity™
The user can enable or disable Video Clarity™ during an ongoing
conference.
To enable or disable Video Clarity:
1
In the Conference List pane, double-click the name of the conference
for which you want to enable or disable Video Clarity
or
right-click the conference name and then click Conference
Properties.
2
3
4
Click the Video Settings tab.
Select or clear the Video Clarity check box as required.
Click OK.
3-72
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Participant Level Operations
Participant Level Operations enable you to modify and control the
connections and statuses of participants in ongoing conferences, as
described in Table 3-7.
Table 3-7 Participant Level Operations
Menu
Option
Button
Description
New
Participant
Define a new participant.For more information about
the New Participant dialog box tab, see Table 3-3 on
page 3-22.
Add
Participant
From
Address
Book
Open the Address Book to select the participant for
the conference.
For more information about the Address Book, see
the RMX 1500/2000/4000 Administrator’s Guide,
"Address Book” on page 5-1.
Connect
Participant
Connect a disconnected defined dial-out participant
to the conference.
Disconnect
Participant
Disconnect the participant from the conference.
Delete
Delete the selected participants from the conference.
Participant
Mute
Audio
Mute the audio transmission from the participant to
the conference.
The Audio Muted indicator appears in the Participants
List and the Unmute Audio button (
) becomes
active.
Unmute
Audio
Resume the participant’s audio transmission to the
conference.
The Mute Audio button (
) becomes active.
3-73
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Table 3-7 Participant Level Operations (Continued)
Menu
Option
Button
Description
Suspend
Video
Suspend the video transmission from the participant
to the conference. The suppressed participant’s video
is not transmitted to the conference but the participant
still receives conference video.
The Suspend Video indicator appears in the
Participants List and the Resume Video button (
)
becomes active.
Resume
Video
Resume the participant’s video transmission to the
conference.
The Suspend Video button becomes active (
).
Block
Audio
To block the audio transmission from the conference
to the participant. When blocked, the participant can
still be heard by the conference.
The Audio Blocked indicator appears in the
Participants List and the Unblock Audio button (
)
becomes active.
Unblock
Audio
Resume the audio transmission from the conference
to the participant.
The Block Audio button (
) becomes active.
Add
Add selected participant’s details to the Participant
Participant
to Address
Book
Address Book.
Move to
Con-
ference
Move the participant to another ongoing
conference.The destination conference is selected
from a displayed list.
View
Participant
Sent Video
Preview the video sent from the participant to the
conference.
View
Participant
Sent Video
Preview the video sent from the conference to the
participant.
3-74
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Table 3-7 Participant Level Operations (Continued)
Menu
Option
Button
Description
Copy
Participant
Copy the all participant’s parameters in preparation
for Pasting into another conference or back into the
current conference..
Cut
Participant
Copy the all participant’s parameters and delete the
participant from the current conference. The
participant can be Pasted into another conference or
back into the current conference.
Paste
Participant
As
Paste the participant into the selected conference as
a new participant with parameters modified via the
Address Book Participant - Properties dialog box.
Abort
H.239
Session
To withdraw the Content Token from the participant
back to the MCU for re-assignment.
Change to
Chair-
Define the selected participant as the conference
leader/chairperson.
person
Change to
Regular
Define the chairperson as a regular participant
without chairperson privileges.
Participant
Change To
Content
Token
Initiate Content Broadcast Control to prevent the
accidental interruption or termination of H.239
Content that is being shared by this participant.
For more information see the RMX 1500/2000/4000
Administrator’s Guide, "Content Broadcast Control”
on page 2-39.
Owner
Cancel
Content
Token
Cancel Content Broadcast Control. For more
information see the RMX 1500/2000/4000
Administrator’s Guide, "Content Broadcast Control”
on page 2-39.
Owner
Connect to
Website
Connect directly to the internal website of the
participant’s endpoint to perform administrative,
configuration and troubleshooting activities.
3-75
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Table 3-7 Participant Level Operations (Continued)
Menu
Option
Button
Description
AGC
(Auto Gain
Control)
Enable AGC for the participant with weak audio signal
during ongoing conferences.
Note: Enabling AGC may result in amplification of
background noise.
Participant
Properties
To view all Participant Properties.
For more information, see the RMX 1500/2000/4000
Administrator’s Guide, "Participant Level Monitoring”
on page 10-15.
Copy Cut and Paste Participant
The RMX user can Copy, Cut and Paste participants between differ rent
conferences running on the RMX, including his/her current conference.
These functions, when used via the RMX Manager, with its ability to
manage multiple RMXs, participants, allows the RMX user to Copy, Cut
and Paste participants between conferences running on different RMXs.
Copy Participant
The Copy command copies all the participant’s properties and makes
them available for pasting. The participant remains connected to his/her
current conference.
To copy a participant:
1
In the Participants List pane, right-click the participant you want to
copy.
3-76
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
2
In the drop-down menu select Copy Participant.
Cut Participant
The Cut command copies all the participant’s properties and makes them
available for pasting. The participant is deleted from his/her current
conference.
To cut a participant:
1
In the Participants List pane, right-click the participant you want to
cut.
3-77
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
2
In the drop-down menu select Cut Participant.
Paste Participant
The Paste command connects the copied or cut participant to the selected
conference.
If the participant was copied, he/she should be deleted from the
conference he/she was copied from, unless it is required that the
participant is connected to two (or more) conferences. (There are
endpoints that permit a participant to be connected to multiple
conferences).
To paste a participant:
1
In the Conferences List pane, click the conference you want to paste the
copied/cut participant into.
2
Right-click in the Participants List pane of the selected conference and
in the drop-down menu select Paste Participant.
or
If you are using the RMX Manager and you want to paste the
participant to a conference to different RMX:
a
b
In the MCUs list pane, click the RMX that is hosting the
conference that is to receive the participant.
In the Conferences list pane, click the conference you want to
paste the copied/cut participant into.
3-78
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
c
Right-click, and in the drop-down menu select Paste Participant.
The participant is connected to the conference.
Paste Participant As
The Paste Participant As command allows the RMX user to create a new
participant using the copied participant’s properties as a template. It
automatically opens the Address Book - Participant Properties dialog box
allowing the RMX user to modify the participant’s properties effectively
creating a new participant. When the OK button in the Participant
Properties dialog box is clicked the new participant is connected to the
selected conference.
To paste a participant as a new participant:
1
In the Conferences List pane, click the conference you want to paste the
copied/cut participant into.
Right-click in the Participants List pane of the selected conference and
in the drop-down menu select Paste Participant As.
or
If you are using the RMX Manager and you want to paste the
participant to a conference on another RMX:
a
b
In the MCUs list pane, click the RMX that is hosting the
conference that is to receive the participant.
In the Conferences list pane, click the conference you want to
paste the copied/cut participant into.
3-79
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
c
Right-click, and in the drop-down menu select Paste Participant
As.
The Address Book - Participant Properties dialog box is displayed.
2
Modify the participant information as required. For more
information see the RMX 1500/2000/4000 Administrator’s
Guid"Modifying Participants in the Address Book” on page 5-14.
Optional. If not already in the Address Book, the copied/cut
participant can be added to the Address Book.
Optional. The new participant can be added to the Address Book.
3-80
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
3
Click the OK button to connect the new participant to the selected
conference.
Personal Layout Control with the RMX Web Client
RMX users can use the RMX Web Client to the change the Video Layouts of
individual participants and force participants to its windows without
affecting the Video Layouts of other participants.
To change a participant’s Video Layout and Video Forcing:
1
In the Participants list, double click the participant or right-click the
participant and then click Participant Properties.
The Participant Properties – Media Sources dialog box opens.
2
In the Layout Type list, select Personal.
Video
Windows
Representation
List of
Conference
Participants
Selected
Layout
3
4
5
Select the number of Video Windows.
Select the required Video Layout.
To video force participants to windows in the selected video layout,
in the window to which you want to force a participant, select the
name of the participant to force from the list of conference
participants.
6
7
Repeat step 5 to force participants to other windows.
Click OK.
3-81
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
To cancel the Personal Video Layout selection and return to the
conference layout:
1
2
3
In the Participant Properties dialog box, select the Media Sources tab.
In the Layout Type list, select Conference.
Click OK.
The participant will now see the conference video layout with its
forced participants.
To cancel the Personal Video Forcing for a window without returning to
the conference layout:
1
In the Participant Properties – Media Sources dialog box, in the video
layout window, select Auto in the Participants list.
2
Click OK.
Switching between participants is renewed and is audio activated.
Personal Layout Selection with Click&View
With the Click&View application, participants can change their Personal
Layouts via DTMF codes entered from their endpoints. This option is
available only if the Click&View option is selected in the Conference IVR
Service.
To change Personal Layout with Click&View:
1
Enable Click&View – on the endpoint’s keypad, enter
.
The Click&View application is displayed on the screen.
When using a Polycom VSX endpoint, an additional
must be entered to
enable the remote DTMF keypad. The full Click&View entry sequence is:
,
.
3-82
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
The Personal Layout keypad options menu is displayed on the video
screen.
2
On the endpoint’s remote keypad, press the number corresponding
to the number of video squares you wish to select.
For example, if you want a four-square video layout, press
.
The video window layout of your screen changes to the first four-
window layout as follows:
Repeated presses of the
key, within eight seconds, cycles through
the following series of four-square layout options:
In any multi-square layout, pressing
to the top left window.
forces the current speaker
In full view, pressing
forces the next participant to full view.
In any video layout, pressing
reverts to the conference layout.
3-83
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
The following table summarizes the Video Layout options available
via Click&View .
Table 3-8 Video Layout Options
Group
DTMF Code
Default
Layout
Group Layout Options
1
2
3
4
5
6
7
8
9
Revert to the previous conference layout.
0 /
Conference Control Using DTMF Codes
Participants and chairpersons can manage their connection to ongoing
conferences from their endpoints, using touch-tone signals (DTMF codes)
from their endpoints. Table 3-9 lists the DTMF Codes that can be used.
Chairpersons can also control an ongoing conference using DTMF codes.
3-84
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Permissions for DTMF actions to be performed by all conference
participants or by chairperson only are configured in the Conference IVR
Service assigned to the conference.
For more information, see the RMX 1500/2000/4000 Administrator’s Guide,
"Defining a New Conference IVR Service” on page 14-9.
To use the DTMF codes to control the conference, the DTMF input must
be first enabled on the endpoint remote control (for example, entering #).
Table 3-9
Default DTMF Codes to Manage Conferences and Participants
Operation
DTMF String
Permission
Conference help
00
Chairperson
All
Initiate PCM
##
Start Click&View
**
All
Individual help
*0
All
Pause Recording
*1
Chairperson
Chairperson
Chairperson
Chairperson
Chairperson
Chairperson
Chairperson
Chairperson
Chairperson
All
Stop Recording
*2
Start/Resume Recording
Enable Roll Call
*3
*42
#42
*43
#43
*5
Disable Roll Call
Roll Call Review Names
Roll Call Stop Review Names
Mute All Except Me
Cancel Mute All Except Me
Mute My Line
#5
*6
Unmute My Line
#6
All
Secure Conference
Unsecure Conference
Increase Listening Volume
Decrease Listening Volume
*71
#71
*76
#76
Chairperson
Chairperson
All
All
3-85
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Table 3-9
Default DTMF Codes to Manage Conferences and Participants
Operation
DTMF String
Permission
Change Password
*77
Chairperson
Change To Chairperson
Play Help Menu
*78
All
*83
All
Mute Incoming Participants
Unmute Incoming Participants
Terminate Conference
Show Participants
*86
Chairperson
#86
Chairperson
*87
Chairperson
*88
All
All
All
All
Increase Broadcast Volume
Decrease Broadcast Volume
Override Mute All
*9
#9
Configurable
Requesting Help
A participant can request help using the appropriate DTMF code from
his/her touch tone telephone or the endpoint’s DTMF input device. The
participant can request Individual Assistance (default DTMF code *0) or
Conference Assistance (default DTMF code 00).
Participants in Entry Queues who failed to enter the correct destination
conference ID or the conference password will wait for operator
assistance (provided that an Operator conference is active).
Participant who is waiting for User (Operator) Assistance is displayed
with the following icons in the Status column of the Participants pane.
Awaiting Individual Assistance – The participant has requested
the user’s (operator’s) assistance.
Awaiting Conference Assistance – The participant has requested
the user’s (operator’s) assistance for the conference. This usually
means that the RMX user (operator) has been requested to join the
conference.
3-86
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Personal Conference Manager (PCM)
The Personal Conference Manager (PCM) interface enables the conference
chairperson to control various conference features using his/her
endpoint’s remote control device.
The following conference operations can be performed:
•
Initiate Polycom’s Click&View™ application to change the local
screen layout.
•
•
•
Invite a participant to connect to the conference.
View and control the audio and video of each connected endpoint.
Camera Control - control the camera of a remote endpoint using
(FECC).
•
•
Control the camera of a connected endpoint.
Video Force a specific participant to a specific window of the video
layout.
•
•
•
Initiate and control recording of the conference.
Disconnect a participant.
Terminate the conference.
Guidelines
•
•
•
PCM is only supported with MPM+ cards.
PCM is only available in CP conferences.
Although the RMX can host up to a maximum of 800 conferences
(depending on the RMX model) PCM can only be activated from 4
conferences per MPM+ card.
—
An RMX 2000 with 2 MPM+80 cards installed can host a total of
8 PCM sessions while an RMX 4000 with 4 MPM+80 cards
installed can host a total of 16 PCM sessions.
—
If 4 PCM sessions are active on an MPM+ card and a chairperson
of another conference, hosted on the same MPM+ card, attempts
to start an additional PCM session, a message indicating
insufficient resources is displayed and FECC is activated.
•
When PCM is active, FECC can only be performed by the chairperson
using PCM’s Camera Control menu.
3-87
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
•
FECC is available to all IP participants in the conference with the
exception of the chairperson that has an active PCM session.
•
•
If enabled, Message Overlay is not displayed while PCM is active.
Normal conference video is resumed after 4 seconds of inactivity
within the PCM menu.
•
•
If a chairperson with active PCM session is moved to another
conference, the PCM session is automatically terminated.
The PCM_LANGUAGE System Flag determines the language of the
PCM interface.
Possible Values: ENGLISH, CHINESE_SIMPLIFIED ,
CHINESE_TRADITIONAL, JAPANESE, GERMAN, FRENCH,
SPANISH, KOREAN, PORTUGUESE, ITALIAN, RUSSIAN,
NORWEGIAN
Default: Current RMX Web Client language.
This System Flag must be added to the System Configuration file before
it can be modified. For more information see the RMX 2000/4000
Administrator’s Guide, "Modifying System Flags” on page 18-5.
•
The Start PCM DTMF code for initiating PCM is configured in DTMF
Codes tab of the New Conference IVR Service or Conference IVR Se vice
Properties dialog box. The default DTMF Code is 1 and can be
modified if required.
3-88
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
The default value of the Permission field is Everyone. It can be
modified to Chairperson.
Everyone /Chairperson
Default DTMF Code ‘##”
3-89
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
PCM Interface
Initiating PCM
For IP endpoints: PCM is activated by pressing the Far key (
)
followed by any of the Arrow Keys on the Remote Control Device.
For ISDN/PSTN endpoints: PCM is activated by pressing ## on the
Remote Control Device.
When PCM becomes active, the top level of the PCM Main Menu is
displayed on the conference chairperson’s endpoint:
Main Menu - Level 1
Arrow Indicator:
There are more menu
options on the next
page
Arrow Indicator:
There are menu
options on the
previous page
Main Menu - Level 2
Right Arrow:
Corresponds to the
Remote Device’s
Right Arrow Key
Action:
Go to Sub-Menu of
Selected Option
(Click&View)
PCM Main Menu - Level 2 can only viewed and accessed by ISDN endpoints by
using DTMF Codes 7 and 8.
3-90
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Remote Control Device Keys
PCM facilitates user interaction with the RMX using DTMF Codes and the
Arrow (FECC) keys of the endpoint’s remote control device.
Menu Navigation - Arrow and Zoom Keys
The PCM Menu is navigated using the Remote Device’s Arrow Zoom Keys
which are defined as follows:
Remote Device
Far Key
Arrow Keys
Zoom Keys
Numeric Keys
They are defined as follows:
Table 3-10 PCM - Menu Navigation
Arrow Key
Description
•
•
Go up one menu level.
Delete the character to the left of the cursor when entering
data.
Left
•
•
•
Exit the PCM menu and return to normal conference video
(from PCM the top level menu.)
Select the video window to the left when navigating a video
layout.
Initiate PCM from a conference.
3-91
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Table 3-10 PCM - Menu Navigation
Arrow Key
Description
•
•
•
Go down one menu level.
Right
Confirm current selection in the PCM menu.
Select the video window to the right when navigating a
video layout.
•
Initiate PCM from a conference.
Up
•
•
Cycle upward through the displayed menu options.
Select the video window above when navigating a video
layout.
•
Initiate PCM from a conference.
Down
•
•
Cycle downward through the displayed menu options.
Select the video window below when navigating a video
layout.
•
Initiate PCM from a conference.
Zoom in (+)
Zoom out (-)
•
•
Confirm current selection in the PCM menu.
Zoom in on the remote camera when using FECC.
•
•
Exit PCM Menu.
Zoom out on the remote camera when using FECC.
3-92
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
DTMF Codes - Numeric Keys
Before using the shortcut number keys 0-9, enable the DTMF function of the
endpoint
according to that endpoint’s configurations.
DTMF codes are entered using the Remote Device Numerics Keys and are
defined as follows:
Table 3-11 PCM - DTMF Codes
Numeric Key
Description
0
•
•
Number input.
Shortcut key to a numbered menu option - when
conference video or the PCM menu is displayed.
•
Return to the conference - when in FECC mode.
1-9
•
•
Number input.
Shortcut key to a numbered menu option - when the
conference video or the PCM menu is displayed.
•
Initiate PCM session on ISDN/PSTN endpoint (1 is the
default for the Start PCM DTMF Code).
*
•
•
Initiate DTMF mode (with Polycom endpoints) - during
a conference or when the PCM menu is displayed.
Enter a period “.” - while entering an IP address.
#
Confirm selection and send information to the RMX.
3-93
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Click&View
With the Click&View application, participants can change their Personal
Layouts using the Arrow Keys or DTMF codes entered using the Numeric
Keys of their endpoints.
For a full description of Click&View see "Personal Layout Selection with
Click&View” on page 3-82.
Invite Participant
This function is not available to chairpersons using PCM with ISDN
endpoints.
To invite a participant to connect to the conference:
1
Use the Up/Down arrow keys to select Invite Participant in the Main
Menu and then press the Right arrow or # key to confirm your
selection.
or
Press the 2 key on the Remote Device.
The Invite Participant sub menu is displayed.
2
Use the Numeric Keys to enter the number of the participant’s
endpoint.
3
4
Press the # key to initiate the call.
Optional.
a
Use the Down arrow to select the Auto button to select from the
following dialing methods:
3-94
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
•
•
•
•
•
H.323
SIP
VoIP
ISDN
PSTN
b
Press the # key to initiate the call.
5
Optional.
a
Use the Arrow Keys to select the Directory button to select the
Alphabetic Grouping sub menu.
The Local Directory is displayed.
Alphabetic
Groupings
Participant List
b
c
Use the Numeric Keys to enter the number of the participant’s
endpoint.
Press # or the Zoom In key to initiate the call.
or
d
Use the Up/Down arrow keys to select a Participant from the
displayed list or use the Up/Down and Left /Right arrow keys to
display other directory listings.
A message, Press # or Zoom In to select, is displayed.
e
Press # or the Zoom In key to initiate the call.
Optional. To display all participants:
a
b
Use the Down arrow and the to select the ALL button.
Use the Zoom In key to display the global directory.
3-95
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
c
Use the Up/Down and Left /Right arrow keys to select a
Participant.
d
Press # or the Zoom In key to initiate the call.
Participants Mute/Status
This function is not available to chairpersons using PCM with ISDN
endpoints.
The chairperson can view and control the audio and video status of each
participant's endpoint. The chairperson can:
•
•
•
•
View the audio and video status of participants.
Mute, block, unmute, unblock participant audio.
Suspend or allow participant video.
Mute all (except chairperson and lecturer).
To view and change the Participants Mute/Status:
1
Use the Up/Down arrow keys to select Participants Mute/Status in
the Main Menu and then press the Right arrow or # key to confirm
your selection.
or
Press the 3 key on the Remote Device.
The Participants Mute/Status sub menu is displayed.
The sub menu displays the Muted, Blocked and Video Suspended status
of all participants’ endpoints. ALL can be selected to mute and
unmute all participant endpoints with the exception of the conference
chairperson and lecturer.
3-96
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
2
3
Use the Up/Down/Left/Right arrow keys to select a Mute, Block or
Suspend status icon.
Use the Zoom In key to toggle the state of the audio and video
channels of the participants’ endpoints.
The status icons are summarized in Table 3-12.
Table 3-12 Participants Mute/Status - Icons
Status
Description
Icon
Audio output from this endpoint is allowed. Other conference
participants can hear the audio from this endpoint.
The endpoint is muted. Other conference participants will not
hear audio from this endpoint.
The audio input to this endpoint is allowed. This endpoint can
hear the conference audio.
The audio output to this endpoint is blocked. This endpoint
cannot receive the conference audio.
Video output from the endpoint is allowed. Other conference
participants can see video from this endpoint.
Video output from the endpoint is suspended. Other
conference participants cannot see video from this endpoint.
The endpoint is neither muted nor blocked.
The endpoint is both muted and blocked.
3-97
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
Camera Control
This function is not available to chairpersons using PCM with ISDN
endpoints.
The endpoint to be controlled must support Far End Camera Control
(FECC).
Using the arrow keys of the remote control device, the chairperson can
control the direction, zoom and focus of a remote endpoint’s camera.
To control a far camera:
1
Use the Up/Down arrow keys to select Camera Control in the Main
Menu and then press the Right arrow or # key to confirm your
selection.
or
Press the 4 key on the Remote Device.
The Camera Control sub menu is displayed.
2
3
Use the Up/Down/Left/Right arrow keys to select the far camera to
be controlled.
A colored frame is displayed around the selected cell in the video
layout.
Use the Zoom In key to activate FECC.
3-98
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Following a 10 second delay, the FECC active icon (
in the video image of the selected site.
) is displayed
Selected Cell for
Far End
Camera Control
4
Use the Up/Down/Left/Right/Zoom In/Zoom Out arrow keys to
control the remote camera.
5
6
Press the 0 key on the remote control to exit FECC.
Use the Zoom Out key on the remote control to return to the
conference video.
Video Force
This function is not available to chairpersons using PCM with ISDN
endpoints.
Video Force enables the chairperson to force the video of a specific
participant to a specific window of the video layout.
To Video Force a participant’s video:
1
Use the Up/Down arrow keys to select Video Force in the Main Menu
and then press the Right arrow or # key to confirm your selection.
or
Press the 5 key on the Remote Device.
3-99
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
The Video Force sub menu is displayed.
2
3
Use the Up/Down/Left/Right arrow keys to select the window of the
video layout that you want the specific participant to be displayed in.
Press the Zoom In key to cycle the display of all participants in the
selected video window until the participant you want to be displayed
appears.
4
Press the Right arrow or # key to confirm your selection.
Recording
This function is not available to chairpersons using PCM with ISDN
endpoints.
If a Recording Link has been set up in the Conference Profile, the conference
chairperson can use the PCM interface to start, pause, resume and stop
recording. If no Recording Link exists, this function appears grayed out and
cannot be selected.
3-100
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
To use the recording functions:
1
Use the Up/Down arrow keys to select Recording in the Main Menu
and then press the Right arrow or # key to confirm your selection.
or
Press the 6 key on the Remote Device.
The Recording sub menu is displayed.
To start recording:
Use the Up/Down arrow keys to select Start Recording and then
press the Right arrow or # key to confirm your selection.
or
Press the 1 key on the Remote Device.
To pause recording:
While recording is in progress, use the Up/Down arrow keys to select
Pause and then press the Right arrow or # key to confirm your
selection.
or
Press the 2 key on the Remote Device.
To resume recording:
While recording is paused, use the Up/Down arrow keys to select
Resume and then press the Right arrow or # key to confirm your
selection.
or
Press the 2 key on the Remote Device.
3-101
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
To stop recording:
While recording is in progress, use the Up/Down arrow keys to select
Stop Recording and then press the Right arrow or # key to confirm
your selection.
or
Press the 3 key on the Remote Device.
PCM Main Menu - Level 2
Drop Participant
To disconnect a participant from the conference:
1
Use the Up/Down arrow keys to navigate to the second page of the
Main Menu
2
Use the Up/Down arrow keys to select Drop Participant and then
press the Right arrow or # key to confirm your selection.
or
Press the 7 key on the Remote Device.
The Drop Participant sub menu is displayed.
3
Using the Up/Down arrow keys, select the participant to be
disconnected and then press the Right arrow or # key to confirm
your selection.
or
Press the Numeric Key on the Remote Device corresponding to the
participant entry.
3-102
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Terminate Conference
Although this function can be accessed and viewed by chairpersons using PCM
with ISDN endpoints, conference termination cannot be executed.
Although this function can be accessed and viewed by chairpersons using
PCM with ISDN endpoints, conference termination cannot be executed.
To terminate a conference:
1
Use the Up/Down arrow keys to navigate to the second page of the
Main Menu
2
Use the Up/Down arrow keys to select Terminate Conference and
then press the Right arrow or # key to confirm your selection.
or
Press the 8 key on the Remote Device.
The Terminate Conference sub menu is displayed.
3
Press the Right arrow key to confirm termination of the conference.
or
Press the Left arrow key to cancel termination of the conference.
3-103
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3-Basic Operation
3-104
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Glossary
This appendix lists the terms and abbreviations that are related to the
Polycom RMX 1500/2000/4000, and are commonly used in the RMX
documentation.
Abbreviation/
Explanation
Term
AGC
Auto Gain Control. A mechanism that regulates noise and
audio volume by keeping the received signal of all
participants balanced.
Bandwidth
Defines the information carrying capacity of a channel. In
analog systems, it is the difference between the highest
frequency that a channel can carry and the lowest,
measured in hertz. In digital systems, bandwidth is
measured in bits per second. The larger a connection's
bandwidth, the more data can be transmitted in a given
amount of time, allowing for greater video resolution and
more sites in a conference. For more information, see
Line Rate.
Bonding
Bandwidth ON Demand INterpolarity Group. A
transmission protocol that aggregates two 64 Kbps B
channels to function as one 128 Kbps channel. When
using several BRI channels, Bonding means that only one
D-channel serves all BRI channels, while the remaining
D-channels are used for data transfer.
See also: BRI.
Bps, Kbps
Bits and kilobits per second; a unit of bandwidth, which is
the amount of data that can flow during one second over a
communications line (using a transmission medium).
1 Kbps = 1000 Bps
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter A-Glossary
Abbreviation/
Term
Explanation
BRI
Basic Rate Interface. A type of ISDN connection for
transiting data, consisting of 3 channels: two B-channels
(each of 64 Kbps) and one D-channel (16 Kbps).
Carrier
A telephone or other company that provides
telecommunication transmission services.
CIF, 4CIF, QCIF
Common Intermediate Format, an optional part of the
ITU-T's H.261 and H.263 standards. CIF specifies 288
non-interlaced luminance lines, that contain 176 pixels.
CIF can be sent at frame rates of 7.5, 10, 15, or 30 per
second. When operating with CIF, the amount of data to
transmit cannot exceed 256 K bits (where K equals
1024).The CIF video format has the capacity to transmit
video images of 352x288 pixels at 36.45 Mbps and 30
frames per second. A 4CIF format has four times the
capacity of CIF; QCIF has quarter the capacity of CIF.
Codec
Coder-decoder. A device that converts voice and video
into digital code, and vice versa. Refers to the endpoint
video camera and video board that are used for
videoconferencing.
Conference
Connection between two or more endpoints exchanging
video and audio information. If only two endpoints are
involved, a conference is called point-to-point and no
MCU is required. If more than two endpoints are involved,
it is called a multipoint conference, and an MCU
(Multipoint Control Unit) is required as the management
system. For more information, see MCU.
CSU
DBA
Channel Service Unit. Customer-provided equipment that
is used as an interface between a communication network
and the data terminal.
Dynamic Bandwidth Allocation. Used to allocate the
bandwidth needed to transmit the additional packets. for
LPR.
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Abbreviation/
Term
Explanation
DTMF
Dual Tone Multi Frequency. A system of coded signals
used by touch-tone telephones in which a specific sound,
frequency or tone is assigned to each key so that the
signal can be easily recognized by a computer. The codes
enable data input and control of voice-processing
systems. DTMF signals can pass through the entire
connection to the destination device and therefore are
used for remote control after the connection with the MCU
is established.
E1 Line
A 2Mb digital switched line used in Europe.
Endpoint
A hardware device, or set of devices, that can call, and be
called by an MCU or another endpoint. For example, an
endpoint can be a phone, a camera and microphone
connected to a PC or an integrated Room System
(conferencing system).
FECC
Far End Camera Control. In certain video cameras, the
accompanying software that enables a participant to
control a remote camera. Used in Continuous Presence
video conferences in conjunction with the LSD option. For
more information, see LSD.
Frame
A group of bits that make up an elementary block of video
data for transmission by certain protocols.
Frame Rate
The number of video frames displayed on-screen during
one second, measured in fps (frames per second).
G.711
ITU-T audio algorithm, 64Kbps, 3.4 kHz.
ITU-T audio algorithm, 64Kbps, 7 kHz.
ITU-T audio algorithm, 16Kbps, 3.4 kHz.
G.722
G.728
Gatekeeper
A type of server that performs two main functions:
translates LAN alias addresses of terminals and gateways
to IP addresses and provides bandwidth management.
H.221
ITU-T standard that defines how to multiplex video, audio,
control, and user data into one serial bit stream.
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter A-Glossary
Abbreviation/
Term
Explanation
H.230
ITU-T standard that defines simple multipoint control
systems procedures and describes network maintenance
functions.
H.231
H.242
H.243
ITU-T standard that defines a set of MCU functions and
operational requirements.
ITU-T standard that defines initiation of communications
between systems and capabilities negotiation procedures.
ITU-T standard that defines initiation of communications
between systems and capabilities negotiation procedures
in multipoint conferences.
H.261
H.263
ITU-T standard that defines the Px64 video coding
algorithm.
ITU-T standard that provides improved compression and
quality of video images at a line rate lower than 384 Kbps.
This standard is not supported by all codecs.
H.264*
H.264
A proprietary Polycom Video compression standard.
ITU-T standard that provides improved compression and
quality of video images in lower line rate connections and
is part of the Highest Common mechanism in Video
Switching conferences.
H.320
H.323
ICE
ITU-T standard that defines how the H-series video
conferencing recommendations work together.
ITU-T standard for audio, video and data communications
across IP-based (LAN) networks, including the Internet.
Interactive Connectivity Establishment (ICE) provides a
structure/protocol to unify the various NAT Traversal
techniques that are used to cross firewalls.
It enables SIP based endpoints to connect while
traversing a variety of firewalls that may exist between the
calling endpoint (local) and the MCU or called endpoint
(remote).
IP
Internet Protocol. The working protocol that forms the
basis of the internet.
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Polycom RMX 1500/2000/4000 Getting Started Guide
Abbreviation/
Term
Explanation
ISDN
Integrated Services Digital Network. A set of protocol and
interface standards (voice, video and data) that comprise
a telephone network. There are two types of ISDN lines:
BRI and PRI.
ITU-T Standard
LAN
International Telecommunications Union,
Telecommunication Standardization Sector (formerly
CCITT). An international group that produces official
standards for telecommunications.
Local Area Network. A group of computers and other
devices linked via a network’s operating system.
LDAP
Lightweight Directory Access Protocol.
Line Rate
The amount of bandwidth used by a communication
device, measured in Kbps (kilobits per second).
LPR
Lost Packet Recovery. An algorithm that creates
additional packets that contain recovery information
necessary to reconstruct lost packets.
MCU
Multipoint Control Unit. Device which allows more than
two sites to be connected in a video conference.
Null modem cable A serial cable designed to eliminate the need for
communication equipment when two digital devices are
directly connected to each other.
Participant
A person using an endpoint to connect to a conference.
When using a Room System, several participants use a
single endpoint.
PRI
Priority Rate Interface. An ISDN interface designed for
high volume data communication. Consists of 23 B
channels of 64 Kbps each and one D channel of 64 Kbps.
In Europe, the PRI line provides 30 B channels + one D
channel.
PSTN
Public Switched Telephone Network.
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter A-Glossary
Abbreviation/
Term
Explanation
QCIF
Quarter CIF. A video format with image size of 176x144
pixels that transmits 9.115 Mbps at 30 frames per second
(a quarter of the capacity of CIF). For more information,
see CIF.
QoS
Quality of Service. QoS defines the performance of a
network service, such as the average delay between
packets.
RS-232
SIP
A standard for serial interface connection.
Session Initiation Protocol. An application-layer protocol
designed to work over IP networks. A SIP service defines
the properties and the IP addresses of the SIP network
components.
Span
An ISDN line or leased line. A span may be of either T1
(United States) or E1 (Europe) type. Also called a circuit.
SRTP
Encryption of SIP Media is supported using SRTP
(Secured Real-time Transport Protocol) and the AES key
exchange method.
T1 Line
ToS
A 1.5Mb digital switched line used in the United States.
Type of Service. ToS defines optimization tagging for
routing audio and video packets.
WAN
Wide Area Network. A communications network that
services a geographical area larger than the LAN.
Whiteboard
An on-screen shared notebook for placement of shared
documents.
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Peerless Industries TV Mount PP730 User Manual
Pelco TV Mount C2227M D User Manual
Philips Camera Lens 6FF3FPB 37 User Manual
Philips Computer Drive FM01SW40 00 User Manual
Philips Computer Drive PCA532K User Manual
Philips Digital Camera SPC1290NC User Manual
Philips Indoor Furnishings P 8515 B User Manual
Philips Microcassette Recorder AQ6345 01Z User Manual
Polar Heart Rate Monitor IR INTERFACE User Manual
POSIFLEX Business Machines Computer Keyboard PST KB136 User Manual