CSi20
CSi30
CSi40
Center Channel Loudspeakers
FXi30
FXi50
Surround FX Loudspeakers
Owner’s
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 1
Most popular placement, above the TV screen. CSi Series Center Speakers are magnetically shielded for safe
placement near TV or video monitors. If you notice video distortion or discoloration, immediately move the
speakers away from the video source and call Polk Audio Customer Service 800.377.7655 (US and Canada)
La ubicación más común es encima de la pantalla del televisor. Los altavoces centrales de la serie
CSi tienen blindaje magnético para poder ubicarlos con seguridad cerca de monitores de televisión
o de video. Si nota que hay distorsión o descoloración de la imagen, aleje inmediatamente los
altavoces de la fuente de video y comuníquese con el servicio al cliente de Polk Audio.
OR
Disposition la plus courante, au-dessus de l’écran. Les enceintes de la série CSi sont blindées
magnétiquement et peuvent être disposées à proximité d’une télé ou d’un moniteur vidéo.
Si vous percevez de la distorsion ou de la décoloration vidéo, éloignez immédiatement les
enceintes de l’écran et communiquez avec le service à la clientèle de Polk.
Häufigste Platzierung – über dem Fernsehbildschirm. CSi-Mittenlautsprecher sind für eine Platzierung in
der Nähe von Fernsehgeräten oder Videomonitoren magnetisch abgeschirmt. Wenn Sie eine Verzerrung
oder Verfärbung des Videobildes bemerken, sind die Lautsprecher umgehend von der Videoquelle zu
entfernen. Setzen Sie sich in diesem Fall mit dem Kundendienst von Polk Audio in Verbindung.
FIGURE 2
Consult serial number label for correct FX speaker orientation.
Note location of Bipole/Dipole switch.
Consulte la etiqueta con el número de serie para orientar
correctamente el altavoz.
LEFT
Pour orienter vos enceintes f/x correctement, consultez l’étiquette
du numéro de série (et non celle de l’interrupteur Bipole/Dipole).
Angaben zur ordnungsgemäßen Ausrichtung der Lautsprecher
finden Sie auf dem Typenschild mit der Seriennummer.
LEFT
FIGURES 3a & b
Direct surround effects using BI-POLE mode.
[a]
[b]
Set Surrounds as “small” in your receiver’s Bass Management settings.
Left
Right
Efectos de sonido surround directo con modalidad BI-POLE.
Asigne la clasificación “pequeño” a los altavoces surround
en los parámetros de control de bajas frecuencias de su receptor.
Pour des effets ambiophoniques directionnels, choisissez le mode
BI-POLE. Réglez le contrôle “surround” de votre récepteur à “small”.
Direkte Surround-Effekte im BIPOL-Modus. Stellen Sie die Surround-
Werte der Tiefen auf Ihrem Empfänger auf ”klein“ ein.
for more information visit our website at www.polkaudio.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Diffuse surround effects—di-pole mode [figure 4]: For a more diffuse effect, place the speakers
on the side walls in line with your listening position and at least 2 feet away from the rear wall.
Select the “dipole” switch setting [figure 2].
Processor Mode Configuration for the FXi Series Surround FX Loudspeaker:
Set Surrounds to “Small” in your receiver’s Bass Management settings.
CONNECTING YOUR LOUDSPEAKERS
[FIGURES 5 & 6]
We recommend 16-gauge or larger speaker wire. Follow the hookup directions included with your
receiver. Strip 1/2 inch (12.7mm) of insulation from each of the two conductors of the wire to
expose the bare metal and twist each of the individual conductors into single unfrayed strands.
Note that one of the terminals on the rear of each speaker is red (+) and the other is black (-).
Make certain that you connect the wire from the red (+) terminal of your amplifier or receiver to
the red (+) terminal on your speaker and the wire from the black (-) terminal of your amplifier
or receiver to the black (-) terminal on your speaker. Most wire has some indicator (such as
color-coding, ribbing or writing) on one of the two conductors to help you maintain consistency.
To connect wire to the binding post [figure 7], unscrew the hex nut and insert the bare wire into
the hole near the base of the binding post. Do not insert the insulated part of the wire into the hole
as this will not give you a good connection. Twist the hex nut back down the binding post until it
firmly meets the wire. Do not over tighten.
To use Banana Plugs (US only): Unscrew the binding post lug nuts completely to expose the
binding post plugs (plastic plugs inserted into the binding posts). Carefully pry out the binding post
plugs to expose banana plug holes. Screw the lug nuts back on the binding posts and insert banana
plugs. (This is for US owners only.)
BI-WIRING OR BI-AMPING THE CSi40
If you decide to bi-wire or bi-amp, you must remove the flat metal jumpers
between terminal posts. Failure to do this could result in damage to your amplifier
and loudspeakers.
Bi-wiring [figure 8] can provide noticeable improvements in the overall transparency of your
loudspeakers. Run separate speaker wires to the low and high frequency drivers from a single
amplifier: after removing the jumpers, connect one set of speaker wires to the upper terminals
on each speaker and one set of (usually heavier gauge) wires to the lower terminals. Connect
the other ends of both wire sets to the corresponding amplifier outputs.
FOR MANUAL UPDATES, VISIT
FOR MORE DETAILED HOOK UP AND PLACEMENT INFORMATION, VISIT
FOR RECOMMENDED ACCESSORIES (INCLUDING SPEAKER STANDS, BRACKETS
AND EXCLUSIVE POLK AUDIO LOGOWEAR), VISIT OUR WEBSTORE:
Contact Polk Audio Customer Service 1-800-377-7655 (Outside US: 410-358-3600), [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 4
Diffuse surround effects using DI-POLE mode.
Set Surrounds as “small” in your receiver’s Bass Management settings.
Efectos de sonido surround difuso con modalidad DI-POLE. Asigne la clasificación “pequeño”
a los altavoces surround en los parámetros de control de bajas frecuencias de su receptor.
Pour des effets ambiophoniques diffus, choisissez le mode DI-POLE. Réglez le contrôle
“surround” de votre récepteur à “small”.
Surround-Effekte lassen sich im DIPOL-Modus verteilen. Stellen Sie die Surround-Werte
der Tiefen auf Ihrem Empfänger auf “klein“ ein.
FIGURE 5
Basic Center Channel Speaker hookup diagram.
Set Center Channel to “small” in your receiver’s
Bass Management settings.
CENTER
Diagrama básico de conexión.
Diagramme de branchement rudimentaire.
Grundlegendes Anschlussdiagramm.
FIGURE 6
Basic Surround FX Speaker hookup diagram.
Set Surrounds to “small” in your receiver’s
Bass Management settings.
Diagrama básico de conexión.
Diagramme de branchement des enceintes
f/x ambiophoniques. Réglez le contrôle des canaux
ambiophoniques de votre récepteur à “small.”
Grundlegendes Anschlussdiagramm.
FIGURE 7
Using binding post connections.
Uso de conexiones con tornillos de presión.
Utilisation des bornes de branchement.
Verwendung von Anschlussklemmen.
Loosen hex nut
Tighten hex nut
Do not insert insulated
section of speaker wire
Insert speaker wire
through hole
Desenrosque parcialmente
la tuerca hexagonal
Enrosque la tuerca de nuevo
Serrer l’écrou
No inserte alambre con
material aislante
Inserte el alambre para
la bocina en el orificio
To use Banana Plugs (US only):
Unscrew the binding post lug nuts completely
to expose the binding post plugs
Desserrer l’écrou
Sechskantmutter festschrauben
Ne pas insérer la partie
isolée du fil du haut-parleur
Insérer le fil du haut-parleur
dans le trou
Sechskantmutter lösen
(plastic plugs inserted into the binding posts).
Carefully pry out the binding post plugs
to expose banana plug holes.
Isolation des Lautsprecher-
Drahtes nicht in das Loch schieben
Lautsprecher-Draht durch
das Loch schieben
Screw the lug nuts back on the binding posts
and insert banana plugs.
FIGURE 8 [CSi40 ONLY]
Bi-wiring, or using separate speaker wire connections
for high and low frequency sections.
(This is for US owners only.)
Bicableado, o uso de conexiones de cables de altavoz
separadas para las secciones de alta y baja frecuencia.
Bi-câblage: l’utilisation de câbles distincts pour brancher les
composantes des hautes et des basses fréquences de vos enceintes.
Verwendung von unterschiedlichen Kabelverbindungen
für hohe und niedrige Frequenzen.
for more information visit our website at www.polkaudio.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Bi-amping [figure 9] allows you to use separate amplifiers for the high and low frequency
sections of your loudspeaker for greater dynamic range and lower distortion. After removing the
jumpers, connect the speaker wires from the high frequency amplifier outputs to the upper set
of terminal posts on each speaker. Follow the same procedure for connecting the low frequency
amplifier outputs to the lower set of terminals. Remember to maintain correct wiring polarity
(+ to +, - to -) in all connections.
WALL MOUNTING THE FXi SERIES SURROUND LOUDSPEAKER
The FX Series Surround Loudspeakers feature built-in wall mounting brackets. Follow the steps
below to safely wall mount these speakers. Wall mounting requires basic skills in with tools such
as a drill and a screwdriver. If you are in doubt that you possess the necessary skills or tools,
consult your Polk Audio dealer, or a professional installer.
• Make sure the material on which you plan to mount the speakers (plaster, drywall, paneling,
stone, etc.) can support the weight of the speakers (FXi30=approx 13lbs/5.9kg ea.,
FXi50=approx 15.5lbs/7kg ea.). Make sure the locations you select do not conceal electrical
wiring or plumbing.
• Prior to installation, hold the speaker in the chosen location to make sure it safely
clears obstacles such as ceiling, adjacent walls, corners, beams, lighting fixtures and
door/window frames.
• Using the keyhole slots in the bracket template (included), mark the installation location
of the four keyhole slots with a pencil [figure 10]. Orient the template so that the small
ends of the keyhole slots are facing “up.”
• If you are certain that there is a stud behind the wall surface, drive a #10 screw (not included)
through the wall and into the stud [figure 11a].
• If there is no stud behind the wall at the chosen location, install a #10 wall anchor (not
supplied) into the wall by following the wall-anchor-manufacturer’s instructions [figure 11b].
• For masonry walls, use a masonry drill bit and #10 masonry anchor and screw (not included).
• Tighten screws into stud or wall anchors, leaving screw heads protruding 1/16” (1.6mm).
• Make all wire attachments now. (See previous page.)
SAFE LIMITS OF OPERATION
• Line up the keyhole slots on the back of the speakers so that the screw heads pass through
the large center hole of the slots.
Your Polk loudspeakers are
made with the highest quality
materials for years of trouble-
free performance. However,
damage to loudspeakers can
occur when an amplifier,
• Let the speaker and slide straight down, allowing the screw head to slip behind the smaller
end of the keyhole slot [figure 12].
• Tug gently on the speaker to make certain that the screws and bracket are properly aligned
and that the wall anchors are secure.
regardless of its wattage, is
made to play at higher listening
levels than its power can clearly
produce (usually beyond the
“1 to 2 o’clock” position on the
volume control). This results
in very high levels of audible
distortion, originating in the
amplifier, that can add a harsh,
gritty sound to music. Contrary
to popular belief, a speaker is
more likely to be damaged by
trying to get too much volume
from a low-powered amp or
receiver than from a high
• If the bracket is not held snug against the wall by the screw heads, remove the speaker
from the wall, drive the screws in a little further and then remount the speaker.
TAKING CARE OF YOUR LOUDSPEAKERS
Your new Loudspeakers are constructed of a rugged material that can be dusted or cleaned with a
damp cloth. Avoid harsh detergents and cleaning fluids, as they can permanently damage your
speakers’ finish [figure 13]. Vacuum the grilles to remove dust.
powered one.
Contact Polk Audio Customer Service 1-800-377-7655 (Outside US: 410-358-3600), [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 9
Bi-amping, or using separate amplifiers for the low and high frequency sections of your speakers.
LOW FREQUENCY
AMPLIFIER
HIGH FREQUENCY
AMPLIFIER
Biamplificación, o uso de amplificadores separados para las secciones de baja y alta frecuencia
de los altavoces.
Bi-amplification: l’utilisation d’amplis distincts pour alimenter les composantes des hautes et des
basses fréquences de vos enceintes.
Verwendung von unterschiedlichen Verstärkern für niedrige und hohe Frequenzen der Lautsprecher.
FIGURE 10
Use template to mark mounting location.
Use la plantilla para marcar la ubicación de montaje.
Utilisez le gabarit pour marquer le lieu de fixation.
Verwenden Sie die Schablone zur Markierung der Befestigungsstelle.
FIGURE 11a & 11b
Use #10 screw for wall stud, use #10 wall anchors + screw for no wall stud.
Use un tornillo n° 10 si hay parales internos en la pared, use anclas de pared n° 10
y un tornillo si no hay.
[a]
Utilisez des vis #10 pour fixation sur montant ou des chevilles d’ancrage #10
avec vis s’il n’y a pas de montant.
Verwenden Sie eine Schraube (Nr. 10) für Wände mit Holzstielverstärkung bzw.
Dübel und Schrauben (Nr. 10) für Wände ohne Holzstielverstärkung.
[b]
FIGURE 12
Slide the speaker down on the screw heads to catch the keyhole slots.
Deslice el altavoz hacia abajo sobre las cabezas de los tornillos para
que entren en las ranuras en forma de cerradura.
Glissez l’enceinte sur les têtes de vis jusqu’à ce que les encoches
en trou de serrure s’enclenchent.
Schieben Sie den Lautsprecher auf die Schraubköpfe herunter,
so dass sie in den Ritzen einrastet.
FIGURE 13
Do not use furniture polish on veneer.
Clean veneer with a damp cloth.
Cuidado del acabado de madera natural.
Entretien de la finition en bois véritable.
Pflege der Holzappretur.
for more information visit our website at www.polkaudio.com
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED FIVE YEAR WARRANTY
Polk Audio, Inc. warrants to the original purchaser only that this Polk Audio Loudspeaker Product (the “Product”) will be free from defects in materials and
workmanship for a period of five (5) years from the date of original retail purchase from a Polk Audio Authorized Dealer. However, this Warranty will automatically
terminate prior to the expiration of the five (5) years if the original retail purchaser sells or otherwise transfers the Product to any other party. The original retail
purchaser shall hereinafter be referred to as “you.” To allow Polk Audio to offer the best possible warranty service, please fill out the Product Registration Card(s)
and send it to the Factory, at the address provided on the Product Cards(s) within ten (10) days of the date of purchase.
Defective Products must be shipped, together with proof of purchase, prepaid insured to the Polk Audio Authorized Dealer from whom you purchased the Product,
or to the Factory at 2550 Britannia Boulevard, Suite D, San Diego, California 92154. Products must be shipped in the original shipping container or its equivalent;
in any case the risk of loss or damage in transit is to be borne by you. If upon examination at the Factory or Polk Audio Authorized Dealer it is determined that the
unit was defective in materials or workmanship at any time during this Warranty period, Polk Audio or the Polk Audio Authorized Dealer will, at its option, repair
or replace this Product at no additional charge, except as set forth below. All replaced parts and Products become the property of Polk Audio. Products replaced
or repaired under this warranty will be returned to you, within a reasonable time, freight prepaid.
This warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping proce-
dures, commercial use, voltage inputs in excess of the rated maximum of the unit, cosmetic appearance of cabinetry not directly attributable to defect in materials
or workmanship, or service, repair, or modification of the Product which has not been authorized or approved by Polk Audio. This warranty shall terminate if the
Serial number on the Product has been removed, tampered with or defaced.
This warranty is in lieu of all other expressed Warranties. If this Product is defective in materials or workmanship as warranted above, your sole remedy shall
be repair or replacement as provided above. In no event will Polk Audio, Inc. be liable to you for any incidental or consequential damages arising out of the use
or inability to use the Product, even if Polk Audio, Inc. or a Polk Audio Authorized Dealer has been advised of the possibility of such damages, or for any claim
by any other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply to you.
All implied warranties on this Product are limited to the duration of this expressed Warranty. Some states do not allow limitation on how long an implied Warranty
lasts, so the above limitations may not apply to you. This Warranty gives you specific legal rights, and you also may have other rights which vary from state to state.
This Warranty applies only to Products purchased in the United States of America, its possessions, and U.S. and NATO armed forces exchanges and audio clubs.
The Warranty terms and conditions applicable to Products purchased in other countries are available from the Polk Audio Authorized Distributors in such countries.
SPECIFICATIONS
CSi30
CSi20
FXi50
FXi30
CSi40
DRIVER COMPLEMENT:
2 - 54"(13.3cm) drivers
1"(2.5cm) tweeter
DRIVER COMPLEMENT:
54"(13.3cm) drivers
w"(1.9cm) tweeter
DRIVER COMPLEMENT:
62"(16.5cm) drivers
2 - 1"(2.5cm) tweeter
DRIVER COMPLEMENT:
54"(13.3cm) drivers
2 - 1"(2.5cm) tweeter
DRIVER COMPLEMENT:
2 - 62"(16.5cm) drivers
1"(2.5cm) tweeter
OVERALL
FREQUENCY RESPONSE:
52Hz-27kHz
OVERALL
FREQUENCY RESPONSE:
55Hz-22kHz
OVERALL
FREQUENCY RESPONSE:
40Hz-27kHz
OVERALL
FREQUENCY RESPONSE:
50Hz-27kHz
OVERALL
FREQUENCY RESPONSE:
40Hz-27kHz
-3DB LIMITS:
55Hz-26kHz
-3DB LIMITS:
60Hz-20kHz
-3DB LIMITS:
50Hz-26kHz
-3DB LIMITS:
55Hz-26kHz
-3DB LIMITS:
50Hz-26kHz
RECOMMENDED
AMPLIFICATION:
10-180 watts/channel
RECOMMENDED
AMPLIFICATION:
10-100 watts/channel
RECOMMENDED
AMPLIFICATION:
10-150 watts/channel
RECOMMENDED
AMPLIFICATION:
10-100 watts/channel
RECOMMENDED
AMPLIFICATION:
10-250 watts/channel
EFFICIENCY (1M,1W):
90dB
EFFICIENCY (1M,1W):
89dB
EFFICIENCY (1M,1W):
90dB
EFFICIENCY (1M,1W):
89dB
EFFICIENCY (1M,1W):
91dB
IMPEDANCE:
Compatible with 8 Ohm Outputs
IMPEDANCE:
Compatible with 8 Ohm Outputs
IMPEDANCE:
Compatible with 8 Ohm Outputs
IMPEDANCE:
Compatible with 8 Ohm Outputs
IMPEDANCE:
Compatible with 8 Ohm Outputs
CROSSOVER FREQUENCY:
2.5kHz
CROSSOVER FREQUENCY:
3.6kHz
CROSSOVER FREQUENCY:
2.5kHz
CROSSOVER FREQUENCY:
2.5kHz
CROSSOVER FREQUENCY:
2.5kHz
CROSSOVER SLOPE:
2rd Order HP,
CROSSOVER SLOPE:
2nd Order HP,
CROSSOVER SLOPE:
2nd Order HP,
CROSSOVER SLOPE:
2nd Order HP,
CROSSOVER SLOPE:
2nd Order HP,
2nd Order LP
1st Order LP
2nd Order LP, selectable
Dipole/Bipole
2nd Order LP, selectable
Dipole/Bipole
2nd Order LP
ENCLOSURE TYPE:
ENCLOSURE TYPE:
ENCLOSURE TYPE:
Ported
Ported
ENCLOSURE TYPE:
ENCLOSURE TYPE:
PowerPort
Ported
Ported
DIMENSIONS:
DIMENSIONS:
DIMENSIONS:
DIMENSIONS:
DIMENSIONS:
62"H x 20"W x 7a"D
7"H x 15"W x 7a"D
72"H x 22s"W x 122"D
(16.5cmH x 50.8cmW x 18.7cmD)
(17.8cmH x 38.1cmW x 18.7cmD)
(19.1cmH x 57.5cmW x 31.8cmD)
14d"H x 10d"W x 94"D
(37.8cmH x 27.6cmW x 23.5cmD)
112"H x 9"W x 84"D
(29.2cmH x 22.9cmW x 21cmD)
SHIPPING WEIGHT:
SHIPPING WEIGHT:
SHIPPING WEIGHT:
19 lbs (8.6kg)
13 lbs (5.9kg)
SHIPPING WEIGHT:
SHIPPING WEIGHT:
28 lbs (12.7kg)
37 lbs (16.8kg)
28 lbs (12.7kg)
POLK AUDIO, INC. • 5601 METRO DRIVE, BALTIMORE, MD 21215 USA • 800.377.7655 • SALES DEPT. FAX: 410.764.5266
WWW.POLKAUDIO.COM
RM0307-1
Download from Www.Somanuals.com. All Manuals Search And Download.
|