P ro d u ct M an u a l
PD P 42"
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning : Serious injury or fatal injury may occur, if the indicated warning is not followed.
Caution : Minor injury or product damage may occur, if the indicated caution is not followed.
Installation - Warning
Do not place any liquid and
foreign objects on or above
the PDP.
· It may cause an electric shock
and a fire. Contact your dealer
for service.
Do not install the PDP where
water (rain) drops can enter
the enclosure, or where
there is oil or humidity.
Do not use or keep it in a
place where combustible
sprays or inflammable
materials are kept.
Do not install the PDP in an
unstable location with a
smaller support area than
the PDP. It may fall and
cause injury.
·
It may cause an electric
shock, a fire, failure or trans-
formation.
·
It may cause an explosion or
a fire.
·
It should be installed on a flat,
stable location.
Installation - Warning
Do not put candles, mos-
quito incense, cigarette
lighters, a heater, or any
other source of heat on or
near the PDP.
Do not place the electric
cord or the plug near an
electric heater.
Install the antenna firmly
and away from high-volt-
age wires and communi-
cation cables.
Do not install in poorly
ventilated locations such
as bookcases or closets.
·
The coating on the electric
cords and the plug may melt
and cause a fire or an electric
shock.
·
It may cause a fire due to
high temperature.
·
If the antenna touches the
high-voltage wire, it may
cause an electric shock or a
fire.
·
It may cause a fire.
Installation Caution
-
The PDP should be installed a
small distance away from walls
or other solid objects in order
to maintain ventilation and to
prevent heat damage.
Be sure to install the monitor
on a level surface.
Blockage of the ventilatior with
table covers or curtains can
cause
a
fire due to the
increased temperature inside
the monitor.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
· Safety precautions
Usage and Maintenance - Warning
During a thunderstorm,
unplug the power cord
and never touch the
antenna cable.
Do not insert any foreign
Do not allow children to
play with the PDP.
Never attempt to disas-
semble, repair or modify
the PDP.
objects such as wires and
drills into the PDP ventilation
slots or the A/V terminal.
· It may cause an electric
shock or a fire.
· It may falls or flip over and
may cause serious injury.
· It may cause an electric
shock or a fire. If it requires
repair, contact your dealer.
· It can cause an electric
shock or a fire.
Usage and Maintenance - Caution
When moving the PDP, turn off
Unplug the PDP if you do
not intend to use it for a
long time. The generation
of heat, insulation degrada-
tion or the accumulation of
dust may cause an electric
fire.
If the PDP is emitting smoke
or an unusual smell, immedi-
ately turn off the power and
unplug the power cord.
When removing the batter-
ies in the remote control,
please place the batteries
in a location out of chil-
dren's reach . It must be
disposed properly.
the power switch and unplug the
power cord from the outlet. Make
sure that the external connection
cords are unplugged (such as
antenna cable and input cables)
prior to moving.
·
It may cause an electric shock
or a fire. Contact your dealer
for the service.
·
The electrical cords may get
damaged and cause an electric
shock or a fire.
When transporting the PDP, The plugs and connectors
at least two people should must be free of dust or
carry it. If it is dropped, seri- water before use. It may
To clean the interior of the
PDP, contact your dealer for
service. A fire or failure may
occur, if it is not cleaned.
When cleaning the PDP,
unplug the electric cord
and wipe with a soft and
dry cloth. Never clean with
chemicals such as industri-
al glaze, wax, benzene,
alcohol, thinner, aromatic,
lubricant, detergent, or a
damp cloth.
ous injury may occur.
cause an electric shock or
a fire.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Considerations for Usage
Still image (immovable) screen may cause permanent damage to PDP.
1. Lengthy display of still images from video games, banners, graphics and others may fatally damage
the screen.
2. When using Picture-In-Picture, permanent damage may occur if the sub-image screen stays on the
corner of screen for a long time.
3. When using the PDP in 4:3 formats with sidebars for a long period of time, it may cause damage to
the plasma panel. It is recommended that you use 16 :9 or Panorama format. (Image burn-in can be
avoided by using "Panel Protection" function or a screen-saver. However, once image burn-in
occurs, it may not disappear completely. An image will be dimmed as the image is displayed long
time or repeatedly.)
※
Any damage to the PDP caused by improper usage (such as image burn-in) shall not be covered
by the warranty.
Defective pixels that can be seen on PDP screen. (illuminated spots, bright spots,
scotoma , blind spot, blinking)
Generally, PDP consists of about 1.22 million pixels and having defective pixels is possible. A PDP
with a number of defective pixels below a certain number is not considered defective. The limited
number of defective pixels does not affect the performance or reliability of the PDP. The standard of
inspection regarding defective pixels is the same or better as the competitor's offering on similar PDP.
It is not subject to replacement or a refund. We will do our best to minimize the defective pixel as best
as we can.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
· Contents
·
Safety precautions
-
-
-
Power Supply ………………………………………………………………2
Installation …………………………………………………………………3
Usage and Maintenance …………………………………………………4
·
·
Considerations for Usage ………………………………………………… 5
Contents ………………………………………………………………… 6 ~7
User Guidance Information
·
·
·
·
Names of each part…………………………………………………… 8 ~9
Options …………………………………………………………………… 10
Accessories…………………………………………………………………11
Installing the PDP
-
-
Installing on a wall ……………………………………………………… 12
Installing on a desktop ………………………………………………… 13
·
Remote controller
-
-
Functions of remote controller buttons ……………………………… 14
Inserting batteries into remote controller …………………………… 15
Connection
·
·
·
·
·
·
Connecting to the VCR ………………………………………………… 16
Connecting to the Cable TV …………………………………………… 17
Connecting to the Camcorder/ Video game console ……………… 18
Connecting to the DVD player ………………………………………… 19
Connecting to the DTV receiver ………………………………… 20 ~21
Connecting to the PC ……………………………………………… 22 ~23
Basic Use
·
·
·
·
Powering the PDP ……………………………………………………… 24
Selecting input source …………………………………………………… 25
Volume……………………………………………………………………… 26
Mute ………………………………………………………………………… 26
6
Download from Www.Somanuals.com. All Manuals Search And Download.
·
·
·
Still ………………………………………………………………………… 26
Info ………………………………………………………………………… 26
Menu ……………………………………………………………………… 27
Application
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
PSM (Picture Status Memory) ………………………………………… 28
Adjusting the screen in USER mode ………………………………… 29
ARC (Aspect Ratio Control) …………………………………………… 30
Watching PIP ……………………………………………………………… 31
PC mode……………………………………………………………… 32~ 33
Color Tone (Pre-Set) …………………………………………………… 34
Color Tone (Manual adjustment) ……………………………………… 35
SSM (Sound Status Memory) ………………………………………… 36
Equalizer …………………………………………………………………… 37
Stereo ……………………………………………………………………… 38
Reset ……………………………………………………………………… 39
Language ………………………………………………………………… 40
Half Tone…………………………………………………………………… 41
Panel Protection ………………………………………………………… 42
PBP Mode ………………………………………………………………… 43
Current Time setting……………………………………………………… 44
On Time/ Off Time (Time setting) ……………………………………… 45
On Time Volume ………………………………………………………… 46
Sleep Timer ……………………………………………………………… 47
Maintenance and Service Part
·
·
·
·
Trouble shooting …………………………………………………… 48~ 50
Supporting display mode………………………………………………… 51
Specifications……………………………………………………………… 52
User Information
7
Download from Www.Somanuals.com. All Manuals Search And Download.
· Names of each part
Front View
Main Power Button
- Please turn off the main power switch, if the PDP will not be
used for a long period of time.
Remote controller Receiving Sensor
Power Supply Indication Lamp
Standby : Red
On : Green
Input Selection Button
Standby
Volume ◀ , ▶ Button
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Back View
External Speaker Connection
RS-232C Terminal
AC Input Terminal
Terminal (8Ω )
AV input (composite)
Terminal
Component (DVD / DTV)
Input Terminal
(480i /480p/720p/1080i)
RGB PC Input Terminal
(VGA / SVGA / XGA)
S-Video Terminal
Audio Input Terminal
(S-Video, Component, DVI)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
· Options
Options
※
To improve the quality of the PDP, specification is subject to change without notice. Please
contact your dealer for current options available.
Desktop Stand
Ceiling - Mount
Bracket
Speaker
Adjustable - Angle
Wall mount
Audio Cable
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
※
The configuration of the components may look different from the following illustration.
RGB Cable
User's Manual
Battery 1.5V( AAA×2)
DVI Adapter
Remote Controller
Power Cord
Video Cable : U.S.A only
Scart RCA Cable
-
: Europe only
: Middle East only
11
Download from Www.Somanuals.com. All Manuals Search And Download.
· Installing the PDP
Installing on the wall
▶ You can install PDP in wall-mounted style as shown in the figure above.
Things to consider
· Please secure enough space for safe use. (Please refer to A and B.)
· Installation of the PDP in an improperly ventilated location can cause a fire or damage to the
PDP due to increased temperature.
A
(
Usage of wall-mount)
※
Contact your dealer to purchase the "Adjustable-angle wall mount" required for wall-mounted installation.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing on a desktop
·
This is not floor-standing unit.
▶ You can install PDP in a desktop style as shown in the figure above.
Things to consider
· Do not install on an unstable location with support area smaller than the PDP.
· Please refer to the desktop stand user's manual for details of installation.
B
(
Usage of stand)
※
Please contact your dealer to purchase the "speakers".
13
Download from Www.Somanuals.com. All Manuals Search And Download.
· Remote controller
※
Functions of remote controller buttons
The remote controller is using Infra-Red (IR). Point it towards the front of the PDP. The remote controller may not
work correctly if it is operated out of range or out of angle.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
If remote controller does not work
1. Check the polarity (+,-) of the batteries in the remote controller.
2. Check that the batteries have power.
3. Check that the PDP is powered and that it is properly plugged in.
4. Check if any three-wavelength lamp, special fluorescent or neon sign is turned on near the PDP.
Inserting batteries into remote controller
1. Firmly press the ▼ part on the
cover and slide the cover in the
direction indicated by the arrow.
2. Insert the batteries, making sure that
the polarities are correct.
3. Close the cover.
CAUTION : Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the national code (Recycling program).
How to use remote controller
·
·
The remote controller should be operated within 30feet(7m) and 30˚ to the left and the right of
the IR receiver on the front of the PDP.
Used batteries should be disposed properly.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
· Connecting to the VCR
· Connecting to the Cable TV
Connecting to the VCR
<Back view of the monitor>
Connecting to the AV Input (composite) terminal
Connect the audio/video cable from audio/ video output terminal of VCR
to the AV Input terminal of PDP. (yellow is for video, white is for audio
(left), red is for audio (right)).
(R)
(L)
Audio
Video S-Video
Connecting to the S-Video terminal
(Use S-Video cable for better image)
Connect the S-Video cable from S-Video terminal of VCR to S-Video ter-
minal of the PDP.
Connect the audio cable from the audio output terminal of VCR to the S-
Video audio input terminal of PDP.
< VIDEO >
How to watch VCR on the PDP
1. Turn on the PDP monitor and press
2. Use
on the remote controller.
.
to select Composite or S-Video and then press
3. Turn on the VCR, insert the tape and then press the Play button.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the Cable TV
<Back view of the monitor>
In order to watch cable TV, subscribe to your local cable TV company
and install a separate converter (Set-Top-Box).
Connecting to the AV Input (composite) terminal
Connect the audio/ video cable from audio/ video output terminal of the Set-
Top-Box to the AV Input terminal of PDP. (yellow is for video, white is for
audio (left), red is for audio (right)).
(R)
(L)
Audio
Video S-Video
Connecting to the S-Video terminal
(Use S-Video cable for better image)
Connect the S-Video cable from S-Video terminal of Set-Top-Box to S-Video
terminal of the PDP.
Connect the audio cable from the audio output terminal of Set-Top-Box to the
S-Video audio input terminal of PDP.
<Cable broadcasting receiver >
How to watch a cable TV
1. Turn on the PDP monitor and press
2. Use
on the remote controller.
.
to select Composite or S-Video and then press
3. Turn on Set-Top-Box and then select the channel you want.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
· Connecting to the Camcorder/ Video game console
· Connecting to the DVD player
Connecting to the Camcorder/ Video game console
<Back view of the monitor>
Connecting to the AV Input (composite) terminal
Connect the audio/ video cable from audio/ video output terminal of the
camcorder/ video game console to the AV Input terminal of the PDP. (yel-
low is for video, white is for audio (left), red is for audio (right)).
(R)
(L)
Audio
Video S-Video
Connecting to the S-Video terminal
(Use S-Video cable for better image.)
Connect the S-Video cable from the S-Video terminal of camcorder/video
game console to the S-Video terminal of PDP.
Connect the audio cable from the audio output terminal of camcorder/
video console unit to the S-Video audio input terminal of PDP.
<Camcorder/ Game machine>
How to watch
1. Turn on the PDP and press
2. Use
on the remote controller.
to select Composite or S-Video and then press
.
3. Turn on the camcorder or video game and set to video mode.
(Please refer to the user's manual of camcorder/video game for more information.)
4. Insert tape into camcorder and press Play button or insert disc into the video game console.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the DVD player
<Back view of the monitor>
Connecting to the component terminal
·
Connect component video cable from the component video out-
put terminal of DVD player to the component terminal (Y, PB
R) of the PDP.
,
(R)
(L)
Y
PB
PR
P
·
·
Connect audio cable from the audio output terminal of DVD
player to the component audio input terminal of the PDP.
You can make S-Video connection or AV Input (composite) con-
nection instead of connecting to component terminal. (Please
refer to page 16 on connection method)
Video
Audio
·
DVD component output terminal is indicated by Y, PB, PR or Y,
<DVD>
CB, CR.
How to watch DVD
1. Turn on the PDP monitor and press
2. Use to select component and then press
3. Turn on DVD player and press Play button.
on the remote controller.
.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
· Connecting to the DTV receiver
Connecting to the Component terminal/ Connecting to the DVI-I terminal
<Back view of the monitor>
(R) (L)
(R) (L)
Y
PB
PR
RGB
COMPONENT
COMPONENT RGB
Audio
<Digital broadcasting>
Video
Connecting to the component terminal/ Connecting to the RGB terminal
· A separate Set-Top-Box may be required to receive digital broadcasting.
· In 1080i mode of DTV mode, the screen size selection is disabled, but fixed to 16:9 the screen size
does not change.
Connecting to the component terminal
Connect component video cable from the component video output terminal of DTV receiver to the com-
ponent terminal (Y, PB, PR) of the PDP.
Connect audio cable from the audio output terminal of DTV receiver to the component audio input termi-
nal of the PDP.
· You can make S-Video connection or AV-Input connection instead of connecting to component termi-
nal. (Please refer to page 16 on connection method)
· DTV component output terminal is indicated by Y, PB, PR or Y, CB, CR
.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the DVI-I terminal
Some of DTV receivers (Set-Top-Box) have an RGB connector (D-sub 15 pin) instead of a component
output. The DVI adapter, which provides this connection terminal for the PDP, may be used for this con-
nection.
Connect the DVI adapter into the VGA cable and connect to the PDP DVI-I input terminal. Connect the
other end of the cable to D-sub output terminal of DTV receiver.
Connect audio cable from the audio output terminal of DTV receiver to the DVI-I audio input terminal of
the PDP.
How to watch DTV
1. Turn on the PDP monitor and press
on the remote controller.
2. Use
to select component and then press
.
3. When connecting DVI-I terminal, use
to select RGB1(Analog) and then press
.
4. Turn the DTV receiver on and select the channel that you want.
·
DTV video output of 480p or 720p will show the clear and detail image of screen.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
· Connecting to the PC
Connecting to the DVI-I terminal
Connecting to the Analog RGB
Connecting to the Analog RGB terminal
Connect DVI adapter into VGA D-Sub cable, then connect to the PDP DVI-I input terminal. Connect the
other end of the VGA Cable to D-sub Video output terminal of PC.
Connect audio cable from the audio output terminal of PC to DVI audio input terminal of the PDP.
(PC audio cable is not included and should be purchased separately.)
※
PC audio works only if a Sound Card is installed.
Connecting to the Digital RGB
Connect DVI cable from the DVI output terminal of PC to the DVI-I input terminal of the PDP.
Connect audio cable from the audio output terminal of PC to the DVI audio input terminal of the PDP.
(The DVI cable and the audio cable should be purchased. Contact your dealer.)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use as PC Monitor
1. Turn on the PDP and press
on the remote controller.
2. Use
to select RGB1(Analog) and then press
.
(If the PC output is set to Digital, select RGB2(Digital).)
3. This PDP does not support Plug & Play function. When setting the PDP, select default.
4. Set the PC video output mode to VGA (640×480)/ SVGA (800×600)/ XGA (1024×768). In the
mode higher than SXGA (1280×1024), "Out of Range" message appears. Be sure to change
your PC video format to less than XGA mode. (Please refer to page 51 for the modes that PDP
supports)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
· Powering the PDP
· Selecting input source
Prior to using the PDP
Insert the power plug.
Connect external equipment properly.
· Please use only after carefully reading this manual.
· Check the power connection to the AC outlet and the connection of AC input to the PDP.
Power On/ Off
·
To turn the PDP on :
Press the "Main Power" button of PDP and then press the "Standby" button.
·
To turn the PDP off :
Press "Standby" button on the PDP and then press the "Main Power" button.
Turning the main power switch off will save energy. It is the same as unplugging the power cord.
If ON Time setting is set, the main power should be ON.
·
To turn on/off by remote controller :
Press the POWER button of remote controller (If the PDP is not turned on, check that the "Main Power"
button on the PDP main body is turned on. The main power indicator will light up red if turned on).
CAUTION -
After turning off the main Power, please wait at least more than 3 seconds to turn the
main power back on.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting input source
Select the required input using
in the pop up menu by pressing
and then select
with
.
Press Composite button, S-VIDEO button, COMPONENT button, RGB1 button, and RGB2 button
on the remote.
Ex) When selecting Analog RGB, press RGB1 button.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
· VOLUME - Adjusting the volume· MUTE - To mute the sound
· STILL - To pause the screen· INFO - To check the current state
· MENU - Checking the menu
VOLUME - Adjusting the volume
Press
for the volume increasing and press
or decreasing.
MUTE - To mute the sound
Press
. If you press the button again, the sound turns back on.
STILL - To pause the screen
Press
. If you press the button again, the screen moves again.
INFO - To check the current state
Press
. The current settings are displayed. It automatically disappears after
three (3) seconds.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU - Checking the menu
If input selections are "AV Input (composite)", "S-video", and "Component", the video menu is activated.
If input selections are "RGB1" or "RGB2", the computer menu is activated.
The remote controller should be used for detailed menu settings and to change the settings.
Press
.
Use
to move the cursor bar up and down in the menu as shown in the figure.
to move to sub menu and store the setting value.
to leave the main menu.
Use
Use
[ Video Mode ]
[ Computer Mode ]
[ Sound Mode ]
[ Equalizer ]
[ Setup Mode ]
[ Timer Mode ]
27
Download from Www.Somanuals.com. All Manuals Search And Download.
· PSM (Picture Status Memory)
· Adjusting the screen in USER mode
PSM (Picture Status Memory)
Press
Press
.
repeatedly to select the desired screen.
Standard
Dynamic
Mild
Game
Movie
User
Press
.
1. Press
2. Press
to move to
.
to get into a sub menu.
3. Select the required mode with
.
·
·
·
·
·
·
Standard : It is the best screen setting (factory setting).
Dynamic : Select when using the PDP in a brightly lit environment.
Movie : Select when watching a movie. Then, *Film mode is operated.
Mild : Select when using the PDP in a dimly lit environment.
Game : Select to enjoy the Video games.
User : Select to set user's preferences.
※ Film mode - It makes video that originated from film smoother, more continuous.
Warning : Shadow image could remain on Dynamic mode due to image sticking phenomenon.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the screen in USER mode
This is available when input signals are one of "AV input(composite)", "S-Video", and "Component".
·
·
Adjustment is possible either in one of preset modes or in User mode.
User defined values are stored in the User mode.
Press
.
1. Press
2. Press
to move to
.
to get into a sub menu.
3. Select the item to adjust with
4. Adjust the setting value with
.
.
Press
after the adjustments are made.
To leave from the main menu, press
again.
User Mode
·
·
·
·
·
Brightness : It adjusts the brightness of the image.
Contrast : It adjusts the contrast of image.
Color : It adjusts the intensity of the color.
Tint : It adjusts the natural tint of the image.
Sharpness : It adjusts the clarity of the image.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
· ARC (Aspect Ratio Control)
· Watching PIP
ARC (Aspect Ratio Control)
Press
Press
.
repeatedly to select the desired screen size.
Panorama
4 : 3
Zoom
16 : 9
Zoom
16 : 9
Panorama
4 : 3
Screen Size
·
·
·
·
16 : 9 - It is a full screen size format.
Zoom - It enlarges the natural screen factor by approx. 5 %
Panorama - It makes 4:3 format fit into 16 : 9 format with minimal loss in content.
4 : 3 - It is the standard format of broadcasting.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Watching PIP (Picture In Picture)
Press
.
The followings will be displayed : Press
to activate PBP at once.
PIP [Large]
PIP [Small]
PBP
Normal
This function will work on Analog RGB, Digital RGB, Composite, S-video, and Component signals as inputs to
main screen and Composite, S-Video and Component (480i) as inputs to sub-screen.
When watching PIP, the main screen and the sub-screen may have differences in the quality of screen color.
PBP only works in S-Video, Composite, Component (480i) input signals.
PIP Input(Changing the input signal of PIP)
The following sub-screen will be selected in order :
Press
.
1. Composite / 2. S-Video / 3. Component.
※Component input will display only 480i input.
PIP position (Moving the sub picture)
As you press
, the location changes as illustrated next.
※If the sub-screen does not appear, (only a black screen is shown)
check to see that input terminal is connected.
PIP Swap (How to exchange the main screen from sub screen)
Press
, and the main/sub screen will be exchanged.
※This does not work in Analog RGB, Digital RGB, and
Component (480p, 720p, 1080i).
PIP Sound Swap (How to exchange the sound from the main to sub)
Press
, the audio of the main/sub screen is exchanged.
PBP MODE (How to exchange the PBP mode)
Press
, the mode of the PBP is exchanged from 16 : 9 to 4: 3.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
· PC mode
Adjusting the computer screen
This is an auto adjustment for Analog RGB only.
Auto adjustment
On Analog RGB use Auto adjustment, When the screen is not focused or centered.
1. Press
.
2. You may have to press
multiple times to auto-adjust properly.
3. If manual compensation is required, adjust it manually.
※ Auto Adjustment works only on Analog RGB signals.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual adjustment
Use this if fine adjustment is required after auto adjustment.
Press
.
1. Press
2. Press
to move to
.
to get into the sub menu.
3. Select the item to adjust with
4. Adjust the setting value with
.
.
Press
after making adjustments to return to the previous menu.
Press it again to leave the menu.
User Mode
· Brightness : It adjusts the brightness of the image.
· Contrast : It adjusts the contrast of the image.
· Phase : It adjusts the phase shift of the image. Use when image appears blurry or out of focus.
· H-Position : It moves the image on the screen horizontally.
· V-Position : It moves the image on the screen vertically.
※Phase, H-Position, V-Position are not adjustable in Digital RGB(RGB2).
33
Download from Www.Somanuals.com. All Manuals Search And Download.
· Color Tone (Pre-set)
· Color Tone (Manual adjustment)
Color Tone (Pre-set)
Press
.
1. Press
2. Press
to move to
.
to get into a sub menu.
3. Select the item "Color Tone" with
.
4. Select the required color among "Cool", "Normal", "Warm", and "User" with
.
Press
after making adjustments to
return to the previous menu.
Press it again to leave the menu.
User Mode
· Cool : This results in a blueish tone.
· Normal : This is standard color setting.
· Warm : This results in a reddish tone.
· User : The user adjustable color of basic color segment of red, green and blue.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Tone (Manual adjustment)
Press
.
1. Press
2. Press
to move to
.
to get into a sub menu.
3. Select the item "Color Tone" with
.
4. Select "User" with
.
5. Press
.
6. Select the item to adjust with
7. Adjust the setting value with
.
.
Press
after making adjustments to return to the previous menu.
Press it again to leave the menu.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
· SSM (Sound Status Memory)
· Equalizer
SSM (Sound Status Memory)
Listening to the selected sound:
Press
.
※Select the pre-set sound mode by pressing the SSM button.
Standard
Music
Speech
Movie
User
Press
.
1. Press
2. Press
to move to
.
to get into sub menu.
3. Select one of the pre-set modes with
.
Press
after the selection to return to the previous menu.
Press it again to leave the menu.
Modes
· Standard : It is the flat sound setting with no equalizer effect at all.
· Music : It is preset for music listening.
· Movie : It is preset sound for watching a movie.
· Speech : It is preset for hearing vocal audio clearly.
· User : Select when listening to the sound to user's preference.
(Please refer to page 37 Equalizer.)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Equalizer
Adjustment is possible in any equalizer mode and will be stored in the user mode.
Press
.
1. Press
2. Press
to move to
.
to get into the sub menu.
3. Select equalizer with
.
4. Press
, then the equalizer menu pop up.
5. Select the menu with
the setting value with
and adjust
.
Press
after making adjustments to return to the previous menu.
Press again to leave the menu.
User Mode
· Volume : It adjusts the sound volume.
· Balance : It adjusts the volume of speakers on the left and the right.
· Equalizer : It adjusts the volume by frequency bands and the user can select the desired sound quality.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
· Stereo
· Reset
Stereo (How to set stereo)
If TV signal reception is poor, the separation of stereo will be bad and noisy. In this occasion, set
the stereo to mono.
Press
.
1. Press
2. Press
to move to
.
to get into the sub menu.
3. Select "Stereo" with
4. Select "Stereo" with
.
.
Press
after making adjustments to return to the previous menu.
Press it again to leave the menu.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Reset (Factory default)
It resets all of the parameters to the factory default.
Press
1. Press
2. Press
.
to move to
.
to get into the sub menu.
3. Reset by pressing
.
Press
after making adjustments to return to the previous menu.
※
The PDP will turn off then turn back on in few seconds. The parameters will be set to factory default.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
· Language
· Half Tone
Language
It adjusts the language of the OSD(On Screen Display) menu.
Press
.
1. Press
2. Press
to move to
.
to get into the sub menu.
3. Select the "Language" with
.
4. Select the desired language with
.
Press
after making adjustments to return to the previous menu.
Press it again to leave the menu.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Half Tone
It changes the background color of the menu frame.
It can be set in a semitransparent or opaque manner.
Press
.
1. Press
2. Press
to move to
.
to get into the sub menu.
3. Select "Half Tone" menu with
.
4. Select "On (Semitransparent)" or "Off (Opaque)" by pressing
.
Press
after making adjustments to return to the previous menu.
Press it again to leave the menu.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
· Panel Protection
· PBP Mode
Panel Protection (How to set the panel protection function)
※It is recommended that the panel protection mode be used on a paused/ frozen screen or on a screen
on which a company's logo remains for a long period.
※There is a possibility that screen flickers during changing panel protection mode. But, it is not a defect.
Press
.
1. Press
2. Press
to move to
.
to get into the sub menu.
3. Select the required panel protection mode with
.
Press after making adjustments to return to the previous menu.
Press it again to leave the menu.
· Scroll : This is a function that scrolls a screen at 10 second intervals.
· Bright Down : This is a function that lowers brightness of the screen for panel protection.
· All : Scroll and Bright Down mode are simultaneously operated.
· Off : Panel Protection mode is not operated.
CAUTION
-
This function does not fully prevent the image sticking that occurs when the fixed
screen continues for long, due to the feature of the panel.(Please refer to page 5)
42
Download from Www.Somanuals.com. All Manuals Search And Download.
PBP Mode
·
It changes the ratio of the PBP screen from 16:9 to 4:3.
Press
.
1. Press
2. Press
to move to
.
to get into the sub menu.
3. Select "PBP Mode" menu with
.
4. Select "Mode 1" or "Mode 2" by pressing
.
Press
after making adjustments to return to the previous menu.
Press it again to leave the menu.
PBP Modes
· Mode 1 : It makes 16:9 PBP ratio.
· Mode 2 : It makes 4:3 PBP ratio.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
· Current Time setting
· On Time / Off Time (Time setting)
Current Time ( How to set the current time)
It sets the current time and then the automatic turn on/off can be set.
The time settings are retained only if the main power is on. If the Main power is off, the time
is reset. To retain the time setting, do not turn the main power switch off.
Press
.
1. Press
to move to
.
2. Press
to get into the sub menu.
Move to "Hour" with
and adjust "Current Hour" with
and then adjust "Current Minute" with
and then select "AM" or "PM" with
.
Move to "Minute" with
Move to "AM" with
.
.
Press
after adjustment to return to the previous menu.
Press it again to leave the menu.
Once "Current Time" is set, "On Time", "Off Time", "On time volume" settings are adjustable.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
On Time / Off Time (Time setting)
Current Time must be set correctly for this function to work.
Press
.
1. Press
2. Press
to move to
.
to get into the sub menu.
3. Select "On Time" or "Off Time" with
.
Move to "Hour" with
Move to "Minute" with
Move to "AM" with
Move to "Off" with
and then adjust the desired "Hour" with
and then adjust the desired "Minute" with
and then select "AM" or "PM" with
.
.
.
and then select "On" with
.
Press
after making adjustments to return to the previous menu.
Press it again to leave the menu.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
· On Time Volume
· Sleep Timer
On Time Volume (How to set the volume)
Current time must be set correctly for this function to work.
Press
1. Press
2. Press
.
to move to
.
to get into the sub menu.
3. Select "On Time Volume" with
.
4. Adjust the desired volume value with
.
Press
after making adjustments to return to the previous menu.
Press it again to leave the menu.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Sleep Timer
It sets time to make automatic turn off for the sleeping.
Press
.
The selection of the sleep timer will appear.
Sleep Timer: OFF
Sleep Timer:
15 Minute
Sleep Timer:
30 Minute
Sleep Timer:
60 Minute
Sleep Timer:
120 Minute
Sleep Timer:
90 Minute
To disable the sleep timer set it to "Sleep Timer: OFF" by pressing
.
※After the sleep timer appears on the screen for more than 20 seconds without pressing the
"Sleep" button, the appeared sleep timer is automatically set.
※To check the current "Sleep timer" setting, press
once.
※Reset the sleep timer again, after the PDP power is turned off.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
· Trouble shooting
In case a problem occurs with your PDP TV, please take the following steps first.
If you still have the problem, turn the power off and contact your dealer or an authorized
service center.
• Screen related Matters
Problem
Action
Is the power plug pulled out? Insert the power plug. Turn
the main power button on and press the power button of
the remote controller.
The screen does not appear.
This problem occurs for a brief time in the process of
image elimination processing in order to hide temporary
screen noise that occurs when the power is turned on. But
if the screen does not come after 1 minute has passed,
contact your dealer or an authorized service center.
The screen appears too
slowly after the power is turned on.
Screen is too bright or too dark.
Screen is too large or too small.
Perform brightness adjustment or Contrast adjustment.
(Please refer to page 37)
Adjust the screen size. (Please refer to page 38)
Stripes appear on the screen
and it shakes.
Stop using wireless telephones, hair driers and
electric drills.
Screen appears in black and white.
Adjust the screen in user mode. (Please refer to page 37)
Check that PDP TV and external equipment are
Simultaneous Screen
does not appear.
connected.
Check the inputs of simultaneous screen by
pressing sub-screen selection.
Press the STILL button. (Please refer to page 28) Check if
the Pause button is pressed on external equipment.
The screen does not move.
Execute automatic adjustment by pressing AUTO ADJ
button. If the screen is still abnormal after automatic
adjustment, perform manual fine adjustment. Please refer
to page 41.
Computer Input Screen is abnormal.
Automatic Turn On does not work.
Automatic Turn On function works only when turning the
PDP TV off with the remote controller or Standby button.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
• Sound related Matters
Problem
Action
1. Press the "Mute"button. (page 26)
2. Increase the sound by pressing volume adjustment
button.
3. Check if voice terminal of external input is connected
properly.
4. Check if speaker cables are connected properly.
5. If it is on PIP mode, convert audio of main screen
and sub-screen by pressing S/SWAP.
6. Select and check the other input.
Screen appears,
but there is no sound.
If the sound still does not work and the other channels
are the same after you have done as the above, contact
your dealer or an authorized service center.
When connecting a Set-Top-Box, check that it is on stereo
broadcasting. If it is, the TV channel may not be available or
the reception may be bad. Select "Mono" (Please refer to
page 38) Check the audio source with another player. If that
source is good, contact your dealer or an Authorized service
center.
Lots of noise (static) occurs.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
· Trouble shooting
· Supporting display mode
• Others
Problem
Action
remote controller does not work.
1. Check if main power is On.
2. Check that the batteries of the remote controller were
loaded properly.
3. Check to see if any obstacle exists between the PDP TV
and the remote controller and remove it, if any.
4. If the batteries have no power, replace them with two
new batteries.
PDP TV makes strange noise.
PDP TV indication lamp is On.
It is the noise when the mechanism expands or contracts
from to changes to the environment due to factors such
as humidity, temperature, etc. It is not a failure.
The red means the Stand-by power is ON. It will take a
few seconds to turn off as the main power is off.
This PDP TV is for household use and registered as suitable on electromagnetic waves.
Therefore, you can use it in every location as well as residential areas.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Supporting display mode
It is optimal screen when the resolution is 640 x 480.
Resolution
Horizontal Frequency (KHz)
Vertical Frequency (Hz)
31.47
37.86
37.50
31.47
35.15
37.88
48.88
46.88
48.36
56.48
60.02
60
72
75
70
56
60
72
75
60
70
75
640×480
720×400
800×600
1024×768
Considerations in Installation
If any signal of unsupported resolution is input, the "Out of Range" message appears.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
· MEMO
· Specifications
R
R
Component Mode
[
]
B), C (P )
B
Y
,
C
(P
Resolution
720×480
Horizontal Frequency (KHz)
Vertical Frequency (Hz)
15.73
15.63
31.47
45.00
44.96
33.75
33.72
60.00
50.00
59.94
60.00
59.94
60.00
59.94
SDTV, DVD 480i
SDTV, DVD 576i
SDTV, 480p
720×480
720×480
1280×720
1280×720
1920×1080
1920×1080
HDTV, 720p
HDTV, 720p
HDTV, 1080i
HDTV, 1080i
Specifications
Aspect Ratio
16 : 9
Screen Size (H×V)
Resolution
920.1×518.4mm
852×480(Wide VGA)
0.36(H)×1.08(V)mm
16.77M(256×256×256)
1000cd/㎡(w/o filter)
1200:1
Cell pitch (H×V)
Displayable Colors
Brightness
Contrast
Color Temperature
Viewing Angle
9500 。K
160 。
NTSC, PAL-M, PAL-N, PAL, SECAM,
SD, HD, VGA, SVGA, XGA
Input signal
RGB Input
AC Input
DVI -Ⅰ(Analog/Digital RGB)
AC100-240V~, 50/60Hz, 4A
320W
Power Consumption
If any signal of unsupported resolution is input, the "Out of Range" message appears.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
· MEMO
· User information
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
User information
Note: This equipment has been tested and found to comply with the
limit for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruc-
tion manual, may cause harmful interference to radio communica-
tions.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to con-
nect the interference at his own expense.
Change or modification not expressly approved by the party respon-
sible for compliance could void the user’s authority to operate the
equipment.
This is a class B product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.
Download from Www.Somanuals.com. All Manuals Search And Download.
|