Optional Firmware Update (Version 1.03) for 2013 Navigation Models:
AVIC-Z150BH and AVIC-X950BH
In this manual, iPhone® 5 and iPod® touch fifth generation will be referred to as “iPhone with Lightning
connector.”
The following preparatory steps must first be undertaken in order to connect an iPhone with Lightning
connector to your AVIC-Z150BH or AVIC-X950BH and use AppRadio Mode.
A. Download the firmware update files
B. Update the firmware on your AVIC-Z150BH or AVIC-X950BH
C. Verify System Application Version
D. Pair your iPhone with Lightning connector with your AVIC-Z150BH or AVIC-X950BH and
establish a connection between your iPhone with Lightning connector and the AVIC-Z150BH
or AVIC-X950BH via Bluetooth wireless technology
E. Connect your iPhone with Lightning connector to your AVIC-Z150BH or AVIC-X950BH using
Pioneer CD-IH202 AppRadio Mode HDMI Interface Cable Kit for iPod/iPhone (sold
separately)
Once Steps A through D have been completed, the [Apps] key on the Home screen will become active,
allowing you to utilize AppRadio Mode.
IMPORTANT
• “iPod source” will no longer be available when using AppRadio Mode with an iPhone with Lightning
connector. To play music and/or video files from your iPhone with Lightning connector, please first
install the free of charge CarMediaPlayer app on your iPhone with Lightning connector and then
launch CarMediaPlayer while in AppRadio Mode.
• If you have previously paired your iPhone with Lightning connector with the AVIC-Z150BH or
AVIC-X950BH, you will have to re-register and connect your device after the firmware update has
been completed.
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Updating the firmware on your AVIC-Z150BH or AVIC-X950BH
IMPORTANT
•
Please DO NOT perform any further steps of this firmware update if the model number is anything
other than AVIC-Z150BH or AVIC-X950BH
•
•
For the AVIC-Z150BH, the model number is located to the left of the volume buttons.
For the AVIC-X950BH, the model number is located centrally, just below the touchscreen.
SD Card or microSD Card Device Requirements:
•
•
•
AVIC-Z150BH, SD or SDHC card, formatted to FAT16 or FAT32, 250MB or larger
AVIC-X950BH, microSD or microSDHC card, formatted to FAT16 or FAT32, 250MB or larger
Ensure that the update folder and file are located within the root (top) folder of your SD or
microSD card. There should be no other files on the SD or microSD card.
• While your AVIC-Z150BH or AVIC-X950BH is being updated, DO NOT turn off the system’s
power. Failure to heed this warning may result in serious damage to your Pioneer GPS
Navigation system.
• DO NOT remove the SD card or microSD card during the firmware update process.
• Performing the firmware update will restore all settings to their default values.
• Disconnect any mobile devices including USB flash drives that are currently connected to
your AVIC-Z150BH or AVIC-X950BH.
Procedure
1. Connect a blank and formatted SD card or microSD card to your computer, and then
locate and copy the “AVICX850” folder and “TESTMODE.KEY” file onto the SD card or
microSD card.
2. Turn your vehicle’s key to the ON position and power up your AVIC-Z150BH or
AVIC-X950BH.
3. Turn the AV source to [OFF].
• If the display is currently showing the map screen, press the ‘MODE’ button on the Pioneer
GPS navigation system to view the AV source screen, then select [OFF].
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Insert the SD Card or microSD Card into your AVIC-Z150BH or AVIC-X950BH.
• The system will automatically recognize the firmware update file, reboot, and start the update
process within a minute.
• If the AV Source screen was not set to [OFF] prior to inserting the SD card or microSD
card, you will only see a black screen and the above update screen will not be visible.
If this is the case, do not turn off power or eject the SD Card or microSD Card for at
least 5 minutes as the update process may be in process. Failure to heed this warning
may result in serious damage to your Pioneer GPS Navigation system.
• The initial update process will take approximately 2 to 3 minutes to complete. The
AVIC-Z150BH or AVIC-X950BH will automatically reboot and the “Program forced write” screen
will appear:
Download from Www.Somanuals.com. All Manuals Search And Download.
5. With the “Program forced write” screen displayed, press the ‘HOME’
button on
your AVIC-X950BH or AVIC-Z150BT.
• The “Program forced write [System uCom Write]” screen will appear:
Program forced write [System uCom Write]
1.SD
2.USB
SD
->
uCom
Progress
EU132SYS [
]
[
]
[
]
2
1
[LEFT/RIGHT]Select Media [MENU]ENTER [AV]BACK
• Confirm the that 1) The SD Version shows 8.06 and 2) the uCom version is lower than 8.06.
• If the SD version is displayed as ”-------“ the data on the SD Card or microSD Card may be
corrupted. Please repeat the firmware download and installation process.
6. If the SD version is correct, and the uCom version is lower than 8.06, press the ‘HOME’
button on your AVIC-X950BH or AVIC-Z150BT to begin the uCom update.
• Do not turn off power or eject the SD card or microSD card while the update is in
progress. Failure to heed this warning may result in serious damage to your Pioneer
GPS Navigation system.
7. Once the uCom update is complete, the AVIC-Z150BH and AVIC-X950BH will automatically
reboot and the “Program forced write” screen will reappear:
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Press the ‘HOME’
button on your AVIC-Z150BH and AVIC-X950BH to view the
“Program forced write [System uCom Write]” screen.
9. Confirm that the uCom version shows 8.06:
Program forced write [System uCom Write]
1.SD
2.USB
SD
EU132SYS [ 8.06
->
uCom
[
Progress
]
]
[
]
[LEFT/RIGHT]Select Media [MENU]ENTER [AV]BACK
10. Eject the SD card or microSD card and turn the vehicle’s key to the OFF position to power
off your AVIC-Z150BH or AVIC-X950BH.
• To eject the SD card from the AVIC-Z150BH, press and hold the Eject button until the
faceplate motorizes down to reveal the SD card slot.
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Verifying System Application Version
1. Turn your vehicle’s key to the ON position and power up your AVIC-Z150BH or
AVIC-X950BH.
2. Press the ‘HOME’
home screen menu:
button on your AVIC-X950BH or AVIC-Z150BT to view the main
3. Press the ‘INFORMATION’
icon to display the system information screen:
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Touch and hold the letters ‘INFO’ in the word Information at the upper left corner of the
screen to access the service information screen:
5. Confirm that the Application Version shows 1.030000
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Pairing and Connecting Your iPhone with Lightning Connector via Bluetooth
Wireless Technology
IMPORTANT
• If you have previously paired your iPhone with Lightning connector to the AVIC-Z150BH or
AVIC-X950BH, you will have to re-register and connect your device after the firmware update has
been completed. Please refer to the “Registering and connecting a Bluetooth device” in your
owner’s manual for additional details.
1. Once you have initially paired your iPhone with Lightning connector to the AVIC-Z150BH
or AVIC-X9550BH, some pop-up notifications will appear on the Pioneer touchscreen
display. The unit will first ask “Would you like to transfer all contacts?”:
• Select “Yes” or “No”, either selection has no impact on AppMode compatibility for an iPhone
with Lightning connector.
o If you select “Yes” the display will show “Transferring contacts from cellular phone
device.” followed by “___ contacts data transferred successfully.” before proceeding to
step 2.
o If you select “No” the display will proceed to step 2.
2. The display will show “This device has Bluetooth Audio capability. Would you like to use
it?”:
• Select “Yes”
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The next screen will ask “Is this Android?”
• Select “No”
4. “Is this device equipped with a Digital AV/VGA Connector?”
• Select “Yes”
5. The screen will then display “Do you want to set this device for the AppRadio Mode?”:
• Select “Yes”
6. The screen will then confirm your AppRadio Mode selection :
• Press “OK”
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Lastly, the display will notify you that “Bluetooth device setting completed.”
• Press “OK”
8. Your iPhone with Lightning connector is now connected via Bluetooth and ready for
AppRadio Mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Connecting Your iPhone with Lightning Connector
IMPORTANT
• The Pioneer CD-IH202 AppRadio Mode HDMI Interface Cable Kit for iPod/iPhone is required (sold
separately).
• A Lightning to USB Cable (Apple Inc. product- supplied with iPhone or sold separately) and a
Lightning Digital AV Adapter (Apple Inc. product, sold separately) are also required.
• AppRadio Mode should only be used in the connection configuration shown. Do not use any other
configuration when connecting your device.
Download from Www.Somanuals.com. All Manuals Search And Download.
|