AUDIO/VIDEO MULTI-CHANNEL
RECEIVER
VSX-1017TXV-K
Register your product at
• Protect your new investment
The details of your purchase will be on file for reference in the event of an
insurance claim such as loss or theft.
• Receive free tips, updates and service bulletins on
your new product
• Improve product development
Your input helps us continue to design products that meet your needs.
• Receive a free Pioneer newsletter
Registered customers can opt in to receive a monthly newsletter.
Operating Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead, within
an equilateral triangle, is intended to alert
the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
D1-4-2-3_En
IMPORTANT SAFETY INSTRUCTIONS
READ INSTRUCTIONS — All the safety and
operating instructions should be read before the
product is operated.
RETAIN INSTRUCTIONS — The safety and
operating instructions should be retained for
future reference.
HEED WARNINGS — All warnings on the product
and in the operating instructions should be
adhered to.
FOLLOW INSTRUCTIONS — All operating and use
instructions should be followed.
CLEANING — The product should be cleaned only
with a polishing cloth or a soft dry cloth. Never
clean with furniture wax, benzine, insecticides
or other volatile liquids since they may corrode
the cabinet.
ATTACHMENTS — Do not use attachments not
recommended by the product manufacturer as
they may cause hazards.
WATER AND MOISTURE — Do not use this
product near water — for example, near a
bathtub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming
pool; and the like.
ACCESSORIES — Do not place this product on an
unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a
child or adult, and serious damage to the
product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer.
GROUNDING OR POLARIZATION
OBJECT AND LIQUID ENTRY — Never push
objects of any kind into this product through
openings as they may touch dangerous voltage
points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any
kind on the product.
SERVICING — Do not attempt to service this
product yourself as opening or removing covers
may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
•
If this product is equipped with a polarized
alternating current line plug (a plug having one
blade wider than the other), it will fit into the
outlet only one way. This is a safety feature. If
you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
•
If this product is equipped with a three-wire
grounding type plug, a plug having a third
(grounding) pin, it will only fit into a grounding
type power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
grounding type plug.
DAMAGE REQUIRING SERVICE — Unplug this
product from the wall outlet and refer servicing
to qualified service personnel under the
following conditions:
•
When the power-supply cord or plug is
damaged.
•
If liquid has been spilled, or objects have fallen
into the product.
POWER-CORD PROTECTION — Power-supply
cords should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the product.
OUTDOOR ANTENNA GROUNDING — If an
outside antenna or cable system is connected to
the product, be sure the antenna or cable
system is grounded so as to provide some
protection against voltage surges and built-up
static charges. Article 810 of the National
Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of
the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of
antenna-discharge unit, connection to
•
•
If the product has been exposed to rain or water.
If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
If the product has been dropped or damaged in
any way.
•
•
When the product exhibits a distinct change in
performance — this indicates a need for service.
REPLACEMENT PARTS — When replacement parts
are required, be sure the service technician has
used replacement parts specified by the
manufacturer or have the same characteristics
as the original part. Unauthorized substitutions
may result in fire, electric shock, or other
hazards.
SAFETY CHECK — Upon completion of any service
or repairs to this product, ask the service
technician to perform safety checks to
determine that the product is in proper
operating condition.
WALL OR CEILING MOUNTING — The product
should not be mounted to a wall or ceiling.
HEAT — The product should be situated away from
heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers)
that produce heat.
CART — A product and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the product
and cart combination to overturn.
grounding electrodes, and requirements for the
grounding electrode. See Figure A.
LIGHTNING — For added protection for this
product during a lightning storm, or when it is
left unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the antenna or cable system. This
will prevent damage to the product due to
lightning and power-line surges.
POWER LINES — An outside antenna system
should not be located in the vicinity of overhead
power lines or other electric light or power
circuits, or where it can fall into such power
lines or circuits. When installing an outside
antenna system, extreme care should be taken
to keep from touching such power lines or
circuits as contact with them might be fatal.
OVERLOADING — Do not overload wall outlets,
extension cords, or integral convenience
receptacles as this can result in a risk of fire or
electric shock.
VENTILATION — Slots and openings in the cabinet
are provided for ventilation and to ensure
reliable operation of the product and to protect
it from overheating, and these openings must
not be blocked or covered. The openings should
never be blocked by placing the product on a
bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in
installation such as a bookcase or rack unless
proper ventilation is provided or the
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
manufacturer’s instructions have been adhered
to.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
POWER SOURCES — This product should be
operated only from the type of power source
indicated on the marking label. If you are not
sure of the type of power supply to your home,
consult your product dealer or local power
company.
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
LOCATION – The appliance should be installed in a
stable location.
GROUND CLAMPS
NONUSE PERIODS – The power cord of the
appliance should be unplugged from the outlet
when left un-used for a long period of time.
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Fig. A
NEC — NATIONAL ELECTRICAL CODE
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate
your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.
Contents
01 Before you start
04 Controls and displays
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Checking what’s in the box. . . . . . . . . . . . . . . . . . . . . . . 7
Ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Loading the batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Operating range of remote control unit . . . . . . . . . . 23
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
05 Listening to your system
02 5 minute guide
Auto playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Listening in surround sound . . . . . . . . . . . . . . . . . . . . 27
Standard surround sound . . . . . . . . . . . . . . . . . . . . . 27
Using the Home THX modes. . . . . . . . . . . . . . . . . . . 28
Using the Advanced surround effects . . . . . . . . . . . 28
Setting the effect options. . . . . . . . . . . . . . . . . . . . . . 29
Listening in stereo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using Front Stage Surround Advance . . . . . . . . . . . . 29
Using Stream Direct . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Listening with Acoustic Calibration EQ . . . . . . . . . . . 30
Choosing the input signal . . . . . . . . . . . . . . . . . . . . . . 30
Using surround back channel processing . . . . . . . . . 30
Using the Virtual Surround Back mode . . . . . . . . . . 31
Using Midnight and Loudness. . . . . . . . . . . . . . . . . . . 32
Using the Sound Retriever . . . . . . . . . . . . . . . . . . . . . . 32
Enhancing dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using the tone controls . . . . . . . . . . . . . . . . . . . . . . . . 32
Introduction to home theater . . . . . . . . . . . . . . . . . . . . . 8
Listening to Surround Sound . . . . . . . . . . . . . . . . . . . . . 8
Automatically setting up for surround sound
(Auto MCACC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Problems when using the Auto MCACC Setup . . . . 10
Playing a source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Better sound using Phase Control. . . . . . . . . . . . . . . . 10
03 Connecting your equipment
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
When making cable connections. . . . . . . . . . . . . . . . . 12
About the video converter . . . . . . . . . . . . . . . . . . . . . . . 12
Connecting your TV and DVD player . . . . . . . . . . . . . . 13
Connecting a satellite/cable receiver or other
set-top box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connecting a DVD/HDD recorder, VCR and other
video sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using the component video jacks . . . . . . . . . . . . . . . . 14
Connecting using HDMI . . . . . . . . . . . . . . . . . . . . . . . . 15
About HDMI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connecting digital audio sources . . . . . . . . . . . . . . . . 16
About the WMA9 Pro decoder. . . . . . . . . . . . . . . . . . 17
Connecting analog audio sources . . . . . . . . . . . . . . . . 17
Connecting a component to the front panel
06 Using the tuner
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Improving FM stereo sound. . . . . . . . . . . . . . . . . . . . 33
Tuning directly to a station . . . . . . . . . . . . . . . . . . . . 33
Saving station presets . . . . . . . . . . . . . . . . . . . . . . . . . 33
Naming station presets . . . . . . . . . . . . . . . . . . . . . . . 34
Listening to station presets . . . . . . . . . . . . . . . . . . . . 34
inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing your speaker system . . . . . . . . . . . . . . . . . . . 18
Connecting the speakers . . . . . . . . . . . . . . . . . . . . . . 18
Placing the speakers. . . . . . . . . . . . . . . . . . . . . . . . . . 19
THX speaker system setup . . . . . . . . . . . . . . . . . . . . . 20
Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connecting external antennas. . . . . . . . . . . . . . . . . . 21
Plugging in the receiver . . . . . . . . . . . . . . . . . . . . . . . . 21
AC outlet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
07 The System Setup menu
Making receiver settings from the System Setup
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Surround back speaker setting . . . . . . . . . . . . . . . . . . 35
Manual MCACC setup . . . . . . . . . . . . . . . . . . . . . . . . . 36
Fine Channel Level . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Fine Speaker Distance . . . . . . . . . . . . . . . . . . . . . . . . 37
Professional Acoustic Calibration EQ . . . . . . . . . . . 37
4
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual speaker setup. . . . . . . . . . . . . . . . . . . . . . . . . . 40
Speaker Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Crossover Network . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Channel Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Speaker Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
THX Audio Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
THX Speaker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
10 Using other functions
Making an audio or a video recording . . . . . . . . . . . . 55
Reducing the level of an analog signal. . . . . . . . . . . . 55
Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Dimming the display . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Switching the speaker impedance . . . . . . . . . . . . . . . 56
Resetting the system . . . . . . . . . . . . . . . . . . . . . . . . . . 56
08 Other connections
11 Controlling the rest of your system
Connecting an iPod. . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Connecting your iPod to the receiver . . . . . . . . . . . . 43
iPod playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Using XM Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Connecting your XM Radio receiver . . . . . . . . . . . . . 44
Listening to XM Radio. . . . . . . . . . . . . . . . . . . . . . . . . 45
Using XM HD Surround . . . . . . . . . . . . . . . . . . . . . . . 45
Saving channel presets . . . . . . . . . . . . . . . . . . . . . . . 45
Using the XM Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Using SIRIUS Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Connecting your SIRIUS Connect Tuner . . . . . . . . . 46
Listening to SIRIUS Radio . . . . . . . . . . . . . . . . . . . . . 47
Saving channel presets . . . . . . . . . . . . . . . . . . . . . . . 47
Using the SIRIUS Menu . . . . . . . . . . . . . . . . . . . . . . . 47
Connecting the multichannel analog inputs . . . . . . . 48
Selecting the multichannel analog inputs . . . . . . . . 48
Speaker B setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Switching the speaker system . . . . . . . . . . . . . . . . . . 48
Bi-amping your front speakers . . . . . . . . . . . . . . . . . . . 49
Bi-wiring your speakers. . . . . . . . . . . . . . . . . . . . . . . . . 49
Connecting additional amplifiers. . . . . . . . . . . . . . . . . 50
Using this receiver with a Pioneer plasma
Setting the remote to control other components . . . 57
Selecting preset codes directly . . . . . . . . . . . . . . . . . . 57
Resetting the remote control presets . . . . . . . . . . . . . 57
Confirming preset codes . . . . . . . . . . . . . . . . . . . . . . . 57
Direct function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Multi Operation and System Off . . . . . . . . . . . . . . . . . 58
Programming a multi-operation or a shutdown
sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Using multi operations . . . . . . . . . . . . . . . . . . . . . . . 59
Using System off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Controls for TVs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Controls for other components . . . . . . . . . . . . . . . . . . 60
Operating other Pioneer components with this
unit’s sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
12 Additional information
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
No sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Other audio problems . . . . . . . . . . . . . . . . . . . . . . . . 63
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
iPod messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
XM radio messages . . . . . . . . . . . . . . . . . . . . . . . . . . 67
SIRIUS radio messages. . . . . . . . . . . . . . . . . . . . . . . 67
Surround sound formats . . . . . . . . . . . . . . . . . . . . . . . 68
Dolby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
DTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Windows MediaTM Audio 9 Professional . . . . . . . . 69
About THX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Listening modes with different input signal
display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Using the SR+ mode with a Pioneer plasma
display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
09 Other Settings
The Input Assign menu. . . . . . . . . . . . . . . . . . . . . . . . . 52
The Other Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . 53
Dynamic Range Control Setup . . . . . . . . . . . . . . . . . 53
Dual Mono Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
LFE Attenuator Setup . . . . . . . . . . . . . . . . . . . . . . . . . 54
SR+ Setup for Pioneer plasma displays. . . . . . . . . . 54
Video Converter Setup . . . . . . . . . . . . . . . . . . . . . . . . 54
formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Cleaning the unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
K041_En
5
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you start
01
Chapter 1:
Before you start
•
Sound Retriever
The Sound Retriever feature employs new DSP
technology that helps bring CD quality sound back to
WMA, MP3 and MPEG-4 AAC audio files by restoring
sound pressure and smoothing jagged artifacts left over
after compression.
Features
•
Advanced Direct Energy design
This receiver offers a new advancement in discrete
design unique to Pioneer for high-power drivability, low
distortion and stable imaging. Through symmetrical
placement of power amplification units, this receiver
generates equal amplifier power to all channels,
eliminating the possibility of one channel dominating a
particular sound field.
•
Front Stage Surround Advance
With the Front Stage Surround Advance feature, you can
enjoy seamless, natural surround sound effects using
only the front speakers, without deteriorating the quality
of the original sound.
•
Easy setup using Multichannel Acoustic
•
HDMI compatibility
Calibration (Auto MCACC)
This receiver is compatible with the HDMI digital video
format, providing you high-definition digital video and
digital audio via a single cable.
Setting up for home theater sound is as easy as
connecting speakers, components like a DVD player, and
a TV. The Auto MCACC Setup, which includes the
advanced features of Professional Acoustic Calibration
EQ, provides a quick yet accurate surround sound setup.
This innovative technology measures the reverb
characteristics of your listening area, allowing you to
customize your system calibration. Moreover, you have
access to the full range of surround sound settings.
•
Built-in video converter
The built-in video converter provides output of all analog
video signals to your TV or monitor (regardless of the type
of connection), allowing you to connect components
using component, S-video, and composite video
connections as you like.
•
iPod Ready
•
THX Select2 certified design
With the new iPod terminal, you’ll be up and running in
no time, now that this receiver’s enhanced compatibility
makes on-screen control of your iPod an added
possibility.
This receiver bears the THX Select2 logo, which means it
has passed a rigorous series of quality and performance
tests covering every aspect of the product. This includes
testing of pre-amplifier and power amplifier performance
and operation, and hundreds of other parameters in both
the digital and analog domain, making your home
theater experience as faithful as possible to what the
director intended.
•
XM and SIRIUS Ready
With the new XM and SIRIUS Radio terminals, you’ll be
up and running in no time. This receiver’s enhanced
compatibility makes XM HD Surround playback as well
as on-screen control of XM and SIRIUS Radio an added
possibility.
•
Dolby Digital and DTS decoding, including Dolby
Digital EX, Dolby Pro Logic IIx, DTS 96/24 and DTS-ES
Dolby Digital and DTS decoding brings theater sound
right into your home with up to six channels of surround
sound, including a special LFE (Low Frequency Effects)
channel for deep, realistic sound effects.
•
Easy-to-use LCD remote control
The remote control gives you not only complete control
over every function of this receiver, but also over the main
functions for other components in your home theater
system. Using a system of preset codes, you can program
the remote to operate a wide range of other equipment.
The built-in Dolby Pro Logic IIx and DTS Neo:6 decoders
not only provide full surround sound decoding for Dolby
Surround sources, but will also generate convincing
surround sound for any stereo source.
Also, with the addition of a surround back speaker, you
can take advantage of the built-in Dolby Digital EX and
DTS-ES decoders for six-channel surround sound.
•
Phase correction
Based on Pioneer’s unique Phase Control Technology,
the Phase Control feature incorporated into this
receiver’s design provides coherent sound reproduction
through the use of phase matching for an optimal sound
image at your listening position.
6
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you start
01
Checking what’s in the box
Installing the receiver
Please check that you’ve received the following supplied
accessories:
• When installing this unit, make sure to put it on a
level and stable surface.
• Setup microphone (cable: 5 m (16.4 ft.))
• Remote control unit
Don’t install it on the following places:
– on a color TV (the screen may distort)
– near a cassette deck (or close to a device that gives off
a magnetic field). This may interfere with the sound.
– in direct sunlight
• AA/IEC R6P dry cell batteries x2
• AM loop antenna
– in damp or wet areas
– in extremely hot or cold areas
– in places where there is vibration or other movement
– in places that are very dusty
• FM wire antenna
• Warranty card
• These operating instructions
– in places that have hot fumes or oils (such as a kitchen)
Ventilation
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat dispersal
(at least 20 cm (8 in.) at the top). If not enough space is
provided between the unit and walls or other equipment,
heat will build up inside, interfering with performance
and/or causing malfunctions.
Loading the batteries
20 cm
(8 inches)
Receiver
Caution
Incorrect use of batteries may result in such hazards as
leakage and bursting. Observe the following precautions:
• Never use new and old batteries together.
Slot and openings in the cabinet are provided for
ventilation and to protect the equipment from
overheating. To prevent fire hazard, do not place anything
directly on top of the unit, make sure the openings are
never blocked or covered with items (such as
• Insert the plus and minus sides of the batteries
properly according to the marks in the battery case.
• Batteries with the same shape may have different
voltages. Do not use different batteries together.
newspapers, table-cloths and curtains), and do not
operate the equipment on thick carpet or a bed.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction’s rules that apply in your country or
area.
• Do not use or store batteries in direct sunlight or
other excessively hot place, such as inside a car or
near a heater. This can cause batteries to leak,
overheat, explode or catch fire. It can also reduce the
life or performance of batteries.
W
7
En
Download from Www.Somanuals.com. All Manuals Search And Download.
5 minute guide
02
C5hampteri2n: ute guide
• Set the subwoofer volume to a comfortable level.
Introduction to home theater
4
Use the on-screen automatic MCACC setup to set up
your system.
Home theater refers to the use of multiple audio tracks to create
a surround sound effect, making you feel like you’re in the middle
of the action or concert. The surround sound you get from a
home theater system depends not only on your speaker setup,
but also on the source and the sound settings of the receiver.
See Automatically setting up for surround sound (Auto
MCACC) below for more on this.
5
Play a DVD, and adjust the volume to your liking.
Make sure that DVD/LD is showing in the receiver’s display,
indicating that the DVD input is selected. If it isn’t, press DVD on
the remote control to set the receiver to the DVD input.
This receiver will automatically decode multichannel Dolby
Digital, DTS, or Dolby Surround sources according to your
speaker setup. In most cases, you won’t have to make
changes for realistic surround sound, but other possibilities
(like listening to a CD with multichannel surround sound)
are explained in Listening to your system on page 27.
In addition to the basic playback explained in Playing a source
on page 10, there are several other sound options you can select.
See Listening to your system on page 27 for more on this.
See also Making receiver settings from the System Setup
menu on page 35 for more setup options.
Listening to Surround Sound
This receiver was designed with the easiest possible setup in mind,
so with the following quick setup guide, you should have your
system hooked up for surround sound in no time at all. In most
cases, you can simply leave the receiver in the default settings.
Automatically setting up for surround
sound (Auto MCACC)
The Auto MCACC Setup measures the acoustic
• Be sure to complete all connections before
connecting this unit to an AC power source.
characteristics of your listening area, taking into account
ambient noise, speaker size and distance, and tests for both
channel delay and channel level. After you have set up the
microphone provided with your system, the receiver uses
the information from a series of test tones to optimize the
speaker settings and equalization for your particular room.
1
Connect your TV and DVD player.
See Connecting your TV and DVD player on page 13 to do
this. For surround sound, you’ll want to hook up using a
digital connection from the DVD player to the receiver.
Make sure you do this before moving on to Playing a
source on page 10.
2
Connect your speakers and place them for optimal
surround sound.
Connect your speakers as shown in Installing your
speaker system on page 18.
Important
• Make sure the microphone and speakers are not
moved during the Auto MCACC Setup.
Where you place the speakers will have a big effect on the
sound. Place your speakers as shown below for the best
surround sound effect. Also see Placing the speakers on
page 19 for more on this.
• Before using the Auto MCACC Setup, make sure that
the headphones are disconnected from this receiver
and the iPod, XM or SIRIUS Radio is not selected as
the input source.
Center (C)
Front
Right (R)
Front
Left (L)
Caution
Subwoofer (SW)
Surround
Right (SR)
• The test tones used in the Auto MCACC Setup are
output at high volume.
Surround
Back
Right (SBR)
DIALOG
E
PHASE
S.RETRIEVER
Listening
position
SYSTEM OFF
SOURCE
INPUT
RECEIVER
SELECT
D.ACCESS
CLASS
ENTER
+10
DISC
Surround
Left (SL)
TOP MENU
MENU
TUNE
Surround
Back Left (SBL)
ST
ST
T.EDIT
ENTER
SETUP
GUIDE
RETURN
TUNE
3
Plug in the receiver and switch it on, followed by
your DVD player, your subwoofer and the TV.
Make sure you’ve set the video input on your TV to this receiver. Check
the manual that came with the TV if you don’t know how to do this.
BAND
XM RADIO
DVD
SIRIUS
TV
DVR
2
TV CONTROL
DVR 1
TV CTRL
RECEIVER
INPUT
TV VOL
TV CH
VOL
CD-R/TAPE
CD
SELECT
iPod
TUNER
8
En
Download from Www.Somanuals.com. All Manuals Search And Download.
5 minute guide
02
1
2
Switch on the receiver and your TV.
If no operations are performed for 10 seconds while the
speaker configuration check screen is being displayed,
the Auto MCACC Setup will resume automatically. In this
case, you don’t need to select ‘OK’ and press ENTER in
step 7.
Connect the microphone to the MCACC SETUP MIC
jack on the front panel.
Place the microphone so that it’s about ear level at your
normal listening position (use a tripod if possible). Make
sure there are no obstacles between the speakers and
the microphone.
• With error messages (such as Ambient Noise or
Microphone Check) select RETRY after checking for
ambient noise (see Problems when using the Auto
MCACC Setup below) and verifying the mic
connection.
S-VIDEO
VIDEO/GAME INPUT
AUDIO
MCACC
SETUP MIC
VIDEO
L
R
DIGITAL IN
PHONES
SYSTEM
SETUP
TUNING/
STATION
TUNER
EDIT
RETURN
TONE
SPEAKERS
MULTI JOG
2.Auto MCACC
Now Analyzing
2.Auto MCACC
Check!
The Auto MCACC display appears once the microphone
is connected.
Front
[
YES
]
]
]
]
]
1
Environment Check
Ambient Noise
Microphone
Center
Surround
SB
[
[
[
[
YES
YES
Yx2
YES
[
[
[
OK
OK
OK
]
]
]
Speaker YES/NO
SUB W.
2. Auto MCACC
OK
:Cancel
:Cancel
10
:
Next
Surr Back System
Normal (SB)
]
The configuration shown on-screen should reflect the
5
actual speakers you have.
Enter
:
Next
:
Cancel
If the speaker configuration displayed isn’t correct, use
ꢀ/ꢁ to select the speaker and ꢂ/ꢃ to change the
setting (and number for surround back). When you’re
finished, go to the next step. If you see an error message
(ERR) in the right side column, there may be a problem
with the speaker connection. If selecting RETRY doesn’t
fix the problem, turn off the power and check the speaker
connections.
3
Make sure ‘Normal (SB)’ is selected then press
ENTER.2
3
4
Make sure ‘TYPE1’ is selected then press ENTER.
2. Auto MCACC
EQ TYPE
TYPE1
•
•
ALL CH ADJUST
7
Make sure ‘OK’ is selected, then press ENTER.
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
Enter
:
Start
:
Cancel
optimum receiver settings for channel level, speaker
distance, and Acoustic Calibration EQ.
5
Follow the instructions on-screen.
Make sure the microphone is connected, and if you’re
using a subwoofer, make sure it is switched on and set to
a comfortable volume level.
Again, try to be as quiet as possible while this is
happening. It may take 2 to 6 minutes.
8
The Auto MCACC Setup has finished! Select
6
Wait for the test tones to finish then confirm the
‘SKIP’ to go back to the System Setup menu.
Be sure to disconnect the microphone from this receiver
upon completion of the Auto MCACC setup.
speaker configuration in the OSD.
A progress report is displayed on-screen while the
receiver outputs test tones to determine the speakers
present in your setup. Try to be as quiet as possible while
The settings made in the Auto MCACC Setup should give
you excellent surround sound from your system, but it is
also possible to adjust these settings manually using the
4
it’s doing this.
6
System Setup menu (starting on page 35).
Note
1 • If you cancel the Auto MCACC Setup, or leave an error message for over three minutes, the screen saver will appear.
• The OSD will not appear if you have connected using the HDMI output to your TV. Use component, S-video, or composite connections for system setup.
2 • If you are planning on bi-amping your front speakers, or setting up a separate speaker system in another room, read through Surround back speaker
setting on page 35 and make sure to connect your speakers as necessary before continuing to step 5.
• If you have THX-certified speakers, make sure YES is selected in THX Speaker Setup on page 42.
3 When TYPE1 is selected, the calibration is set for ALL CH ADJUST; when TYPE2 is selected, the calibration is set for both ALL CH ADJUST and FRONT
ALIGN. For details on the correction of each setting, see Professional Acoustic Calibration EQ on page 37.
4 Do not adjust the volume during the test tones. This may result in incorrect speaker settings.
5 If you’re using the front panel display, the diagram in Listening to Surround Sound above indicates (in bold) how each speaker is displayed.
6 • Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm (5 inches) will end up with different
size settings. You can correct the setting manually using the Manual speaker setup on page 40.
• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and
room characteristics into account) and generally does not need to be changed.
9
En
Download from Www.Somanuals.com. All Manuals Search And Download.
5 minute guide
02
Problems when using the Auto MCACC Setup
If the room environment is not optimal for the Auto
MCACC Setup (too much background noise, echo off the
walls, obstacles blocking the speakers from the
microphone) the final settings may be incorrect. Check
for household appliances (air conditioner, fridge, fan,
etc.), that may be affecting the environment and switch
them off if necessary. If there are any instructions
showing in the front panel display, please follow them.
Better sound using Phase Control
This receiver’s Phase Control feature uses phase
correction measures to make sure your sound source
arrives at the listening position in phase, preventing
unwanted distortion and/or coloring of the sound (see
illustration below).
PHASE CONTROL OFF
• Some older TVs may interfere with the operation of
the microphone. If this seems to be happening,
switch off the TV when doing the Auto MCACC Setup.
Front speaker
Listening
position
?
Playing a source
Sound
source
Here are the basic instructions for playing a source (such
as a DVD disc) with your home theater system.
Subwoofer
PHASE CONTROL ON
GUIDE
TV CONTROL
SYSTEM OFF
INPUT
Listening
position
RECEIVER
SOURCE
Front speaker
INPUT
SELECT
TV VOL
TV CH
VOL
SELECT
ANT
REC
INFO
MUTE
MPX
REC STOP JUKEBOX
AUDIO SUBTITLE
DISP
HDD
CH
DVD
CH
XM RADIO
DVD
SIRIUS
TV
DVR
2
PHOTO
STEREO/
F.S.SURR
Sound
source
DVR 1
TV CTRL
RECEIVER
THX
STANDARD ADV.SURR
CD-R/TAPE
CD
Subwoofer
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
iPod
TUNER
Phase Control technology provides coherent sound
reproduction through the use of phase matching for an
optimal sound image at your listening position. The
default setting is on and we recommend leaving Phase
Control switched on for all sound sources.
1
Switch on your system components and receiver.
4
Start by switching on the playback component (for
example a DVD player), your TV and subwoofer (if you
have one), then the receiver (press ꢀ RECEIVER).
1
• Make sure the setup mic is disconnected.
XM RADIO
SIRIUS
DVR
2
DVD
TV
DVR 1
TV CTRL
CD-R/TAPE
CD
2
Select the input source you want to play.
iPod
TUNER
SB ch
RECEIVER
You can use the input source buttons on the remote
control, INPUT SELECT, or the front panel controls.
SLEEP
ANALOG
ATT
2
SR+
DIMMER
PHASE
MIDNIGHT/
LOUDNESS
DIALOG
E
S.RETRIEVER
DISC
3
Press AUTO SURR to select ‘AUTO SURROUND’ and
3
D.ACCESS
CLASS
ENTER
+10
start playback of the source.
If you’re playing a Dolby Digital or DTS surround sound
DVD disc, you should hear surround sound. If you are
playing a stereo source, you will only hear sound from the
front left/right speakers in the default listening mode.
•
Press RECEIVER then PHASE (PHASE CONTROL) to
switch on phase correction.
The PHASE CONTROL indicator on the front panel lights.
• See also Listening to your system on page 27 for
information on different ways of listening to sources.
4
Use the volume control to adjust the volume level.
Turn down the volume of your TV so that all sound is
coming from the speakers connected to this receiver.
Note
1 Make sure that the TV’s video input is set to this receiver. (For example, if you connected this receiver to the VIDEO 1 jacks on your TV, make sure that
the VIDEO 1 input is now selected.)
2 If you need to manually switch the input signal type press SIGNAL SEL (page 30).
3 • You may need to check the digital audio output settings on your DVD player or digital satellite receiver. It should be set to output Dolby Digital, DTS
and 88.2 kHz / 96 kHz PCM (2 channel) audio, and if there is an MPEG audio option, set this to convert the MPEG audio to PCM.
• Depending on your DVD player or source discs, you may only get digital 2 channel stereo and analog sound. In this case, the receiver must be set to a
multichannel listening mode (see Listening in surround sound on page 27 if you need to do this) if you want multichannel surround sound.
4 Phase matching is a very important factor in achieving proper sound reproduction. If two waveforms are ‘in phase’, they crest and trough together,
resulting in increased amplitude, clarity and presence of the sound signal. If a crest of a wave meets a trough (as shown in the upper section of the diagram
above) then the sound will be ‘out of phase’ and an unreliable sound image will be produced.
10
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
03
Chapter 3:
Connecting your equipment
This receiver provides you with many connection possibilities, but it doesn’t have to be difficult. This page explains the
kinds of components you can connect to make up your home theater system.
Rear panel
T
IN
V
iP
5
IN
5
Control input/output
Caution
Use to connect other Pioneer components so that you
can control all your equipment from a single IR remote
sensor.
• Before making or changing the connections, switch
off the power and disconnect the power cord from the
power outlet. Plugging in should be the final step.
ꢄ Operating other Pioneer components with this unit’s
sensor on page 61.
1
HDMI connectors (x3)
Two inputs and one output for high-quality audio/video
connection to compatible HDMI devices.
6
Stereo analog audio source inputs/(outputs) (x3)
Use for connection to audio sources such as CD players,
tape decks, turntables, etc.
ꢄ Connecting analog audio sources on page 17.
ꢄ Connecting using HDMI on page 15.
2
XM Radio input
ꢄ See Using XM Radio on page 44.
7
Component video connections (x4)
Use the inputs to connect any video source that has
component video output, such as a DVD recorder. Use
the output for connection to a monitor or TV.
3
Coaxial digital audio inputs (x2)
Use for digital audio sources, including DVD players/
recorders, digital satellite receivers, CD players, etc.
ꢄ Using the component video jacks on page 14.
ꢄ See also The Input Assign menu on page 52 to assign
the inputs.
8
iPod input terminal
Use to connect your Apple iPod as an audio source.
4
Optical digital audio output/input(s) (x4)
Use the OUT jack for recording to a CD or MiniDisc
recorder.
ꢄ Connecting an iPod on page 43.
9
Audio/video source inputs/(outputs) (x6)
Use for connection to audio/visual sources, such as DVD
players/recorders, VCRs, etc. Each set of inputs has jacks
for composite video, S-video and stereo analog audio.
ꢄ Connecting digital audio sources on page 16.
Use the IN jacks for digital audio sources, including DVD
players/recorders, digital satellite receivers, CD players,
etc.
ꢄ Connecting a DVD/HDD recorder, VCR and other video
sources on page 14.
ꢄ See also The Input Assign menu on page 52 to assign
the inputs.
10 AM and FM antenna terminals
Use to connect indoor or outdoor antennas for radio
broadcasts.
ꢄ Connecting antennas on page 20.
11
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
03
11 Multichannel pre-amplifier outputs
Use to connect separate amplifiers for front, center,
surround, surround back and subwoofer channels.
ꢄConnecting additional amplifiers on page 50 (see also
Installing your speaker system on page 18 for powered
subwoofer connection).
When making cable connections
• To avoid hum, do not lay connected cables over the
top of the receiver.
12 Composite and S-video monitor outputs
Use to connect monitors and TVs.
ꢄ Connecting your TV and DVD player on page 13.
13 Multichannel analog audio inputs
7.1 channel inputs for connection to a DVD player with
multichannel analog outputs.
ꢄ Connecting the multichannel analog inputs on
page 48.
• When connecting optical cables, be careful when
inserting the plug not to damage the shutter
protecting the optical socket.
14 SIRIUS Radio input
ꢄ Using SIRIUS Radio on page 46.
15 Speaker terminals
Use for connection to the main front, center, surround
and surround back speakers.
ꢄ Installing your speaker system on page 18.
• When storing optical cable, coil loosely. The cable
may be damaged if bent around sharp corners.
16 Switched AC power outlet (100 W/0.8 A max.)
Use to power another component in the system. Power to
the outlet switches on and off with the receiver.
About the video converter
ꢄ AC outlet on page 21.
When the video converter is enabled, all analog video
sources are output through all of the MONITOR VIDEO
OUT jacks (HDMI and component video cannot be
1
converted). See Video Converter Setup on page 54 to
switch the video converter on or off.
If several video components are assigned to the same
input function (see The Input Assign menu on page 52),
the converter gives priority to component, S-video, then
composite (in that order).
• For optimal video performance, THX recommends
switching video conversion (in Video Converter Setup
on page 54) OFF.
This product incorporates copyright protection technology
that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
consumer uses only unless otherwise authorized by
Macrovision. Reverse engineering or disassembly is
prohibited.
Note
1 You must connect your monitor/TV to the receiver’s HDMI/component video outputs when connecting these video sources. If the video signal does not
appear on your TV or plasma display, try adjusting the resolution settings on your component or display. Note that some components (such as video game
units) have resolutions that may not be converted. In this case, use an (analog) S-video or composite connection.
12
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
03
2
Connect a composite or S-video output on your
DVD player to the DVD/LD VIDEO or DVD/LD S-VIDEO
input.
Connecting your TV and DVD player
Connect using a standard video cable or an S-video
cable.
1
VIDEO S-VIDEO
3
Connect a coaxial-type digital audio output on
IN
IN
your DVD player to the COAXIAL 1 (DVD/LD) input.
Use a coaxial cable designed for digital audio.
1
TV
4
Connect the stereo audio outputs on your DVD
VSX-1017TXV
player to the DVD/LD AUDIO inputs.
ANTENNA
Connect using a stereo RCA/phono jack cable.
OPTICAL
DIGITAL
OUT
IN
1
• If your DVD player has multichannel analog outputs,
you can connect these instead. See also Connecting
the multichannel analog inputs on page 48.
AM LOOP
L
PRE OUT
L
COMPONENT VIDEO
CENTER
(
)
DVD/LD
IN
1
Y
PB
PR
Y
PB
PR
(
DVR/
VCR1
IN
1
OUT
)
IN
2
IN
2
(
)
TV/SAT
IN
2
Y
IN
3
(
)
TV/SAT
PB
PR
Y
PB
3
PR
IN
(
3
)
SUB
R
SUR-
ROUND
ASSIGNABLE
1
CD
WOOFER
ASSIGNABLE
1
3
S-VIDEO
SIRI
HDM
ASSIG-
NABLE
IN
IN
I
T
IN
OUT
OUT
IN
MONITOR
OUT
CONTROL
OUT
iPod
IN
Connecting a satellite/cable receiver or
other set-top box
1
2
VIDEO
XM
IN
IN
CENTER
AUDIO
L
IN
OUT
IN
IN
IN
L
Satellite and cable receivers, and terrestrial digital TV
tuners are all examples of so-called ‘set-top boxes’.
IN
(
1
)
DVD/LD
R
IN
2
(
)
DVR/VCR2
R
CD
DVD/LD TV/SAT
DVR/VCR1
DVR/VCR2
SUB
FRONT
COAXIAL
WOOFER
ASSIGNABLE
MULTI CH IN
ANTENNA
OPTICAL
1
2
DIGITAL
OUT
IN
1
AM LOOP
PR
L
COMPONENT VIDEO
CENTER
(
)
DVD/LD
L
IN
1
Y
P
B
P
R
Y
P
B
P
R
(
DVR/
VCR1
IN
1
OUT
)
IN
2
IN
2
(
)
TV/SAT
IN
2
Y
IN
3
(
)
TV/SAT
P
B
P
R
Y
P
3
B
P
R
IN
CD
3
)
R
SUB
R
ASSIGNABLE
1
(
FRONT WOOFER
ASSIGNABLE
OUT
1
3
S-VIDEO
HDMI
ASSIG-
NABLE
IN
IN
IN
IN
OUT
OUT
IN
IN
MONITOR
OUT
CONTROL
OUT
iPod
IN
1
2
VIDEO
XM
IN
OPTICAL
COAXIAL
R
AUDIO
L
S-VIDEO
VIDEO OUT
IN
DIGITAL OUT
ANALOG OUT
AUDIO
IN
OUT
IN
IN
L
IN
(
3
4
2
R
IN
2
(
)
DVR/VCR2
R
CD
CD-R/TAPTV/SAT
DVR/VCR1
DVR/VCR2
FRONT
COAXIAL
ASSIGNABLE
MULTI CH
1
2
VSX-1017TXV
DVD player
The diagram shows a basic setup of this receiver together
with a TV and DVD player, with S-video or composite
video connections. Different TVs and DVD players may
offer alternative connections. See also Using the
DIGITAL OUT
component video jacks on page 14 if your TV and/or DVD
player has component video inputs/outputs. If your DVD
player offers multichannel analog audio outputs, see
Connecting the multichannel analog inputs on page 48.
R
AUDIO
L
VIDEO
S-VIDEO
AV OUT
1
Connect the MONITOR OUT video jack to a video
input on your TV.
Use a standard RCA/phono jack video cable to connect to
the composite video jack, or for higher quality video, use
an S-video cable to connect to the S-video jack.
STB
Note
1 If your DVD player only has an optical digital output, you can connect it to one of the optical inputs on this receiver using an optical cable. When you set
up the receiver you’ll need to tell the receiver which input you connected the player to (see The Input Assign menu on page 52).
13
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
03
1
Connect the audio/video outputs on the set-top
1
Connect the audio/video outputs of the video
box to the TV/SAT AUDIO and VIDEO inputs.
Connect using a stereo RCA/phono jack cable and a
video or S-video cable.
player/recorder to the DVR/VCR1 AUDIO and VIDEO
inputs.
Use a stereo RCA/phono jack audio cable for the audio
connection and a video or S-video cable for the video
connection.
1
2
Connect an optical-type digital audio output from
2
your set-top box to the OPTICAL 2 (TV/SAT) input.
• For a second recorder, use the DVR/VCR2 IN inputs.
Use an optical cable for the connection.
2
If the device can record, connect the DVR/VCR1
AUDIO and VIDEO outputs to the recorder’s audio/
video inputs.
Use a stereo RCA/phono jack audio cable for the audio
connection and a video or S-video cable for the video
connection.
Connecting a DVD/HDD recorder, VCR
and other video sources
This receiver has two sets of audio/video inputs and
outputs suitable for connecting analog or digital video
devices, including DVD/HDD recorders and VCRs.
• For a second recorder, use the DVR/VCR2 outputs.
3
If the device can output digital audio, connect an
3
VSX-1017TXV
optical-type digital audio output from the recorder to
the OPTICAL 1 (DVR/VCR1) input.
ANTENNA
OPTICAL
DIGITAL
OUT
4
Use an optical cable for the connection.
IN
1
AM LOOP
PRE OUT
L
COMPONENT VIDEO
CENTER
(
)
DVD/LD
L
L
S
IN
1
Y
P
B
P
R
Y
P
B
P
R
(
DVR/
VCR1
IN
1
OUT
• For a second recorder, use the COAXIAL 2 (DVR/
VCR2) inputs.
)
IN
2
IN
2
(
)
TVT
IN
2
Y
IN
3
(
)
TV/SAT
P
B
P
R
Y
P
3
B
P
R
(
3
)
R
SUB
R
SUR-
ROUND
ASSIGNABLE
1
CD
FRONT WOOFER
ASSIGNABLE
OUT
1
3
S-VIDEO
SIRIU
HDMI
ASSIG-
NABLE
IN
IN
IN
OUT
IN
IN
MONITOR
OUT
CONTROL
OUT
iPod
IN
1
2
Using the component video jacks
VIDEO
XM
IN
IN
Component video should give superior picture quality
when compared to composite or S-video. You can also
take advantage of progressive scan video (if your source
and TV are both compatible), which delivers a very stable,
flicker-free picture. See the manuals that came with your
TV and source component to check whether they are
compatible with progressive-scan video.
CENTER
AUDIO
L
IN
OUT
IN
IN
OUT
L
IN
(
1
)
DVD/LD
R
IN
2
(
)
DVR/VCR2
R
CD
CD-R/TAPE/MD DVD/LD TV/SAT
DVR/VCR1
/VCR2
SUB
WOOFER
FRONT
AXIAL
SSIGNABLE
MULTI CH IN
2
OPTICAL COAXIAL
DIGITAL OUT
R
AUDIO
L
VIDEO S-VIDEO
R
AUDIO
L
VIDEO S-VIDEO
AV OUT
AV IN
3
1
2
DVR, VCR, etc.
Note
1 If your set-top box only has a coaxial digital output, you can connect it to one of the coaxial inputs on this receiver using a coaxial digital audio cable.
When you set up the receiver you’ll need to tell the receiver which input you connected the set-top box to (see The Input Assign menu on page 52).
2 If your satellite/cable receiver doesn’t have a digital audio output, you can skip this step.
3 • In order to record, you must connect the analog audio cables (the digital connection is for playback only).
• If your video component doesn’t have a digital audio output, you can skip this step.
4 If your recorder only has a coaxial digital output, you can connect it to one of the coaxial inputs on this receiver using a coaxial digital audio cable. When
you set up the receiver you’ll need to tell the receiver which input you connected the recorder to (see also The Input Assign menu on page 52).
14
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
03
The HDMI connection transfers uncompressed digital
video, as well as almost every kind of digital audio that the
connected component is compatible with, including
DVD-Video, DVD-Audio (see below for limitations), Video
CD/Super VCD, CD and MP3.
VSX-1017TXV
ANTENNA
OPTICAL
DIGITAL
OUT
IN
AM LOOP
P
1
COMPONENT VIDEO
CENTER
(
)
DVD/LD
L
L
IN
1
Y
P
B
P
R
Y
Y
P
B
P
R
(
DVR/
IN
1
OUT
)
VCR1
IN
2
IN
2
(
)
TV/SAT
IN
2
IN
3
(
)
TV/SAT
P
B
P
R
P
B
P
R
R
SUB
R
HDMI/DVI-equipped component
ASSIGNABLE
1
3
FWOOFER
ASSIGN
OUT
1
3
-VIDEO
HDMI
ASSIG-
NABLE
HDMI OUT
IN
IN
IN
OUT
IN
IN
OU
OUT
IN
IN
MONITOR
OUT
CONTROL
OUT
iPod
IN
1
2
VIDEO
XM
IN
1
AUDIO OUT
IN
DIGITAL OUT
L
AUDIO
R
AUDIO
L
IN
OUT
IN
IN
OUT
L
3
IN
(
1
)
DVD/LD
R
IN
2
ANTE
OPTICAL
(
)
DVR/VCR2
R
CD
CD-R/TAPE/MD DVD/LD TV/SAT
DVR/VCR1
DVR/VCR2
DIGITAL
OUT
FRONT
COAXIAL
ASSIGNABLE
IN
1
MULTI CH
AM
1
2
COMPONENT VIDEO
(
)
DVD/LD
L
IN
1
Y
PB
PR
Y
Y
PB
PR
(
DVR/
VCR1
IN
OUT
)
IN
2
IN
2
(
)
TV/SAT
2
Y
IN
3
(
)
TV/SAT
PB
PR
PB
3
PR
IN
(
3
)
R
ASSIGNABLE
1
CD
ASSIGNABLE
OUT
1
3
S-VIDEO
HDMI
ASSIG-
NABLE
IN
IN
IN
OUT
IN
OUT
CONTROL
OUT
iPod
IN
1
2
VIDEO
XM
IN
Y
IN
AUDIO
L
IN
OUT
IN
IN
IN
P
B
R
1
)
VD/LD
P
R
IN
2
(
)
DVR/VCR2
CD
CD-R/TAPE/MD DVD/LD TV/SAT
DVR/VCR1
DVR/
COAXIAL
2
COMPONENT
VIDEO
ASSIGNABLE
1
2
TV
VSX-1017TXV
Y
2
P
B
R
P
HDMI IN
COMPONENT
VIDEO
1
DVD player
HDMI/DVI-compatible monitor
or plasma display
1
Connect the component video outputs of your
source to a set of ASSIGNABLE COMPONENT VIDEO
inputs.
Connect using a three-way component video cable.
1
Use an HDMI cable to connect the HDMI IN 1/2
interconnect on this receiver to an HDMI output on
your HDMI component.
• Since they are assignable, it doesn’t matter which
component video inputs you use for which source.
After connecting everything, you’ll need to assign the
component video inputs—see The Input Assign
menu on page 52.
2
Use an HDMI cable to connect the HDMI OUT
interconnect on this receiver to an HDMI interconnect
1
on an HDMI-compatible monitor.
• The arrow on the cable connector body should be
facing right for correct alignment with the connector
on the player.
2
Connect the COMPONENT VIDEO OUT jacks to the
component video inputs on your TV or monitor.
Use a three-way component video cable.
Connecting using HDMI
If you have an HDMI or DVI (with HDCP) equipped
component, you can connect it to this receiver using a
commercially available HDMI cable.
Note
1 • To see the on-screen display, you must also connect your TV to this receiver with a composite video, component video or S-video cable.
• For optimum performance, the output settings for an HDMI component (screen resolution, the DeepColor feature, etc.) should be coincided with the
ones that an HDMI-compatible monitor connected adopts.
15
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
03
3
To hear audio from your HDMI component through
this system, make analog and/or digital connections as
necessary.
On the rear panel, you must connect to the audio jacks
from a set of audio/video inputs (for example, DVR/VCR1
or DVR/VCR2 as shown in the illustration).
Connecting digital audio sources
This receiver has both digital inputs and outputs,
allowing you to connect digital audio components for
playback and for making digital recordings.
Most digital components also have analog connections.
See Connecting analog audio sources on the following
page if you want to connect these too.
• Without this connection, HDMI audio will still be
output from your TV or plasma display (though no
sound will be heard from this receiver).
VSX-1017TXV
4
Assign the HDMI input(s) you connected to the
corresponding input source.
ANTENNA
OPTICAL
DIGITAL
If the connected HDMI component is different from the
default settings for the HDMI input terminals of this
receiver, you need to change the settings specified in
Assigning the HDMI inputs on page 53.
OUT
IN
1
AM
L
COMPONENT VIDEO
(
)
DVD/LD
L
IN
1
Y
PB
PR
Y
PB
PR
(
DVR/
VCR1
IN
1
OUT
)
IN
2
IN
2
(
)
TV/SAT
IN
2
Y
IN
3
(
)
TV/SAT
PB
PR
Y
PB
3
PR
IN
CD
3
)
R
ASSIGNABLE
1
(
ASSIGNABLE
5
Use the input source buttons to select the input
O
1
3
S-VIDEO
source you assigned in the previous step, then press
SIGNAL SEL to select the audio input signal.
You can also use the front panel controls to do this (see
Choosing the input signal on page 30).
E
IN
IN
IN
OUT
OUT
IN
OUT
OUT
CONTROL
OUT
iPod
IN
1
2
VIDEO
XM
IN
IN
AUDIO
L
IN
OUT
IN
IN
IN
IN
(
1
)
DVD/LD
• If the video signal does not appear on your TV or
plasma display, try adjusting the resolution settings
on your component or display. Note that some
components (such as video game units) have
resolutions that may not be displayed. In this case,
use an (analog) S-video or composite connection.
R
IN
2
(
)
DVR/VCR2
CD
CD-R/TAPE/MD DVD/LD TV/SAT
DVR/VCR1
DVR/V
COAXIAL
ASSIGNABLE
1
2
About HDMI
HDMI (High Definition Multimedia Interface) supports
both video and audio on a single digital connection for
use with DVD players, DTV, set-top boxes, and other AV
devices. HDMI was developed to provide the
technologies of High Bandwidth Digital Content
Protection (HDCP) as well as Digital Visual Interface
(DVI) in one specification. HDCP is used to protect digital
content transmitted and received by DVI-compliant
displays.
1
2
OPTICAL COAXIAL
DIGITAL OUT
OPTICAL
DIGITAL IN
HDMI has the capability to support standard, enhanced,
or high-definition video plus standard to multi-channel
surround-sound audio. HDMI features include
uncompressed digital video, a bandwidth of up to 2.2
gigabytes per second (with HDTV signals), one connector
(instead of several cables and connectors), and
communication between the AV source and AV devices
such as DTVs.
CD-R, MD, DAT, etc.
1
1
Connect an optical-type digital audio output on
your digital component to the DIGITAL 3 (CD) input.
Use an optical cable for the connection.
2
For recording equipment, connect the optical-type
DIGITAL output to a digital input on the recorder.
2
HDMI, the
logo and High-Definition
Use an optical cable to connect to the DIGITAL OUT.
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
Note
1 • If your digital component only has a coaxial digital output, you can connect it to one of the coaxial inputs on this receiver using a coaxial cable. When
you set up the receiver you’ll need to tell the receiver which input you connected the component to (see also The Input Assign menu on page 52).
• The digital outputs from other components can be connected to any spare digital audio inputs on this receiver. You can assign them when setting up
the receiver (see also The Input Assign menu on page 52).
2 In order to record some digital sources, you must make analog connections as explained in Connecting analog audio sources below.
16
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
03
About the WMA9 Pro decoder
TM
Connecting a component to the front
panel inputs
This unit has an on-board Windows Media Audio 9
1
Professional (WMA9 Pro) decoder, so it is possible to
playback WMA9 Pro-encoded audio using a coaxial or
optical digital connection when connected to a WMA9
Pro-compatible player. However, the connected PC, DVD
player, set-top box, etc. must be able to output WMA9 Pro
format audio signals through a coaxial or optical digital
output.
The front panel inputs comprise a composite video jack
(VIDEO), an S-video jack (S-VIDEO), stereo analog audio
inputs (AUDIO L/R) and an optical digital audio input
(DIGITAL). You can use these connections for any kind of
audio/video component, but they are especially
convenient for portable equipment such as camcorders,
video games and portable audio/video equipment.
Connecting analog audio sources
S-VIDEO
VIDEO/GAME INPUT
AUDIO
MCACC
SETUP MIC
VIDEO
L
R
DIGITAL IN
This receiver features two stereo audio-only inputs. One
of these inputs (CD-R/TAPE/MD) has corresponding
outputs for use with audio recorders.
PHONES
SYSTEM
SETUP
TUNING/
STATION
TUNER
EDIT
RETURN
TONE
SPEAKERS
MULTI JOG
ANTENNA
OPTICAL
DIGITAL
OUT
IN
1
AM LOOP
PRE OUT
L
COMPONENT VIDEO
CENTER
(
)
DVD/LD
L
L
IN
1
Y
P
B
P
R
Y
P
B
P
R
(
DVR/
VCR1
IN
1
OUT
)
IN
2
IN
2
(
)
TV/SAT
IN
2
Y
IN
3
(
)
TV/SAT
P
B
P
R
Y
P
3
B
P
R
IN
CD
3
)
R
SUB
R
SUR-
ROUND
VIDEO OUTPUT
DIGITAL OUT
ASSIGNABLE
1
(
FRONT WOOFER
ASSIGNABLE
OUT
1
3
S-VIDEO
SIRIU
HDMI
TV game, video camera, etc.
ASSIG-
NABLE
IN
IN
IN
OUT
IN
IN
OUT
OUT
IN
IN
MONITOR
OUT
CONTROL
OUT
iPod
IN
1
2
VIDEO
XM
IN
• Select these inputs by pressing VIDEO/GAME or
using INPUT SELECT (remote) to select VIDEO/
GAME.
IN
CENTER
AUDIO
L
OUT
IN
IN
OUT
L
IN
1
(
DVD
IN
2
(
)
DVR/VCR2
R
CD
CD-R/TAPE/MD DVD/LD TV/SAT
DVR/VCR1
DVR/VCR2
SUB
WOOFER
FRONT
COAXIAL
ASSIGNABLE
MULTI CH IN
1
2
VSX-1017TXV
OUT
PLAY
IN
REC
R
L
AUDIO IN/OUT
Tape deck, etc.
•
Connect the analog audio outputs of the source
component to one of the AUDIO inputs.
Connect using a stereo RCA/phono jack audio cable.
• If you’re connecting a tape deck, MD recorder, etc.,
connect the analog audio outputs (OUT) to the
analog audio inputs on the recorder.
Note
1 • Windows MediaTM and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries.
• With WMA9 Pro, sound problems may occur depending on your computer system. Note that WMA9 Pro 96 kHz sources will be downsampled to 48 kHz.
17
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
Installing your speaker system
03
To take full advantage of the receiver’s surround sound
capabilities connect front, center, surround and
main surround speakers should always be connected as
a pair, but you can connect just one surround back
speaker if you like (it must be connected to the left
surround back terminal). You can use speakers with a
nominal impedance between 6 Ω to 16 Ω (please see
Switching the speaker impedance on page 56 if you plan
to use speakers with an impedance of less than 8 Ω).
surround back speakers, as well as a subwoofer.
Although this is ideal, other configurations with fewer
speakers—no subwoofer or no center speaker, or even no
surround speakers—will work. At the very least, front left
and right speakers only are necessary. Note that your
Front
right
Front
left
Subwoofer
Center
LINE LEVEL
INPUT
CAUTION
These speaker terminals carry
HAZARDOUS LIVE voltage.
To prevent the risk of electric
shock when connecting or
disconnecting the speaker
cables, disconnect the power
cord before touching any
uninsulated parts.
OPTICAL
DIGITAL
OUT
IN
1
AM LOOP
L
PRE OUT
AC OUTLET
COMPONENT VIDEO
DVD/LD
L
L (Single)
CENTER
(
)
IN
1
Y
PB
PR
Y
PB
P
(
DVR/
VCR1
IN
1
)
IN
2
IN
2
(
)
TV/SAT
IN
2
Y
(
)
TV/SAT
R
PB
PR
Y
PB
3
PR
IN
CD
3
)
R
SUB
FRONT WOOFER
R
SUR-
ROUND
SURROUND BACK
ASSIGNABLE
1
(
SWITCHED 100 W(0.8 A) MAX
ASSIGNABLE
OUT
1
3
S-VIDEO
SIRIUS
HDMI
ASSIG-
NABLE
IN
IN
IN
IN
OUT
OUT
IN
OUT
OUT
IN
IN
MONITOR
OUT
SPEAKERS
FRONT
CONTROL
OUT
iPod
IN
1
2
CENTER
SURROUND
SURROUND BACK
/
A
B
VIDEO
R
L
R
L
R
L
( )
Single
XM
IN
IN
CENTER
AUDIO
L
IN
OUT
IN
IN
IN
L
L
L
IN
(
1
)
DVD/LD
R
IN
2
(
)
DVR/VCR2
SEE INSTRUCTION MANUAL
SELECTABLE
R
R
R
CD
CD-R/TAPE/MD DVD/LD TV/SAT
DVR/VCR1
DVR/VCR2
SUB
FRONT
SUR-
SURROUND
COAXIAL
WOOFER
ROUND BACK
ASSIGNABLE
MULTI CH IN
1
2
VSX-1017TXV
Surround
left
Surround
right
Surround
back left
Surround
back right
Connecting the speakers
Caution
Each speaker connection on the receiver comprises a
positive (+) and negative (–) terminal. Make sure to
match these up with the terminals on the speakers
themselves.
• Make sure that all the bare speaker wire is twisted
together and inserted fully into the speaker terminal.
If any of the bare speaker wire touches the back panel
it may cause the power to cut off as a safety measure.
18
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
03
• When placing speakers near the TV, we recommend
using magnetically shielded speakers to prevent
possible interference, such as discoloration of the
picture when the TV is switched on. If you do not have
magnetically shielded speakers and notice
discoloration of the TV picture, move the speakers
farther away from the TV.
Bare wire connections
Make sure that the speaker cable you’re going to use is
properly prepared with about 10 mm ( /8 in.) of insulator
stripped from each wire, and the exposed wire strands
3
twisted together (fig. A).
To connect a terminal, unscrew the terminal a few turns
until there is enough space to insert the exposed wire
(fig. B). Once the wire is in position, tighten the terminal
until the wire is firmly clamped (fig. C).
• If you’re using a center speaker, place the front
speakers at a wider angle. If not, place them at a
narrower angle.
fig. A
fig. B
fig. C
• Place the center speaker above or below the TV so
that the sound of the center channel is localized at
the TV screen. Also, make sure the center speaker
does not cross the line formed by the leading edge of
the front left and right speakers.
10 mm (3/8 in.)
• It is best to angle the speakers towards the listening
position. The angle depends on the size of the room.
Use less of an angle for bigger rooms.
Banana plug connections
If you want to use speaker cables terminated with banana
plugs, screw the speaker terminal fully shut then plug the
banana plug into the end of the speaker terminal.
• Surround and surround back speakers should be
positioned 60 cm to 90 cm (1.5 ft. to 3 ft.) higher than
your ears and titled slight downward. Make sure the
speakers don’t face each other. For DVD-Audio, the
speakers should be more directly behind the listener
than for home theater playback.
• Try not to place the surround speakers farther away
from the listening position than the front and center
speakers. Doing so can weaken the surround sound
effect.
Important
• To achieve the best possible surround sound, install
your speakers as shown below. Be sure all speakers
are installed securely to prevent accidents and
improve sound quality.
• Please refer to the manual that came with your
speakers for details on how to connect the other end
of the speaker cables to your speakers.
• Other connections on page 43 provides greater detail
on alternate speaker setups, such as using speaker
system B (page 48), bi-amping (page 49) and bi-
wiring (page 49).
Front
left
Front
right
Center
Subwoofer
• If you are using a THX certified subwoofer use the
THX INPUT jack on the subwoofer (if your subwoofer
has one) or switch the filter position to THX on your
subwoofer.
Surround
left
Surround
right
Placing the speakers
Listening position
Where you put your speakers in the room has a big effect
on the quality of the sound. The following guidelines
should help you to get the best sound from your system.
Surround back left
Surround back right
• The subwoofer can be placed on the floor. Ideally, the
other speakers should be at about ear-level when
you’re listening to them. Putting the speakers on the
floor (except the subwoofer), or mounting them very
high on a wall is not recommended.
Single surround back speaker
Caution
• Make sure that all speakers are securely installed.
This not only improves sound quality, but also
reduces the risk of damage or injury resulting from
speakers being knocked over or falling in the event of
external shocks such as earthquakes.
• For the best stereo effect, place the front speakers
2 m to 3 m (6 ft. to 9 ft.) apart, at equal distance from
the TV.
19
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
03
The diagrams below show suggested surround and
surround back speaker orientation. The first diagram
(fig. A) shows orientation with one surround back speaker
(or none) connected. The second (fig. B) shows
Connecting antennas
Connect the AM loop antenna and the FM wire antenna
as shown below. To improve reception and sound quality,
connect external antennas (see Connecting external
antennas below).
orientation with two surround back speakers connected.
90º to 120º
fig. a
fig. b
fig. c
RS
LS
RS
RS
LS
0º to 60º
LS
3
SBL
SBR
SBL SBR
SB
ANTENNA
fig. A
fig. B
5
FM UNBAL 75
Ω
AM LOOP
• If you have two surround back speakers THX
4
recommends placing them together and the same
distance from your listening position (see below).
1
2
THX speaker system setup
If you have a complete THX speaker system, follow the
diagram below to place your speakers. Note that the
surround speakers ( indicates bi-polar radiating
speakers) should output at an angle parallel to the
listener.
1
Pull off the protective shields of both AM antenna
wires.
2
Push open the tabs, then insert one wire fully into
each terminal, then release the tabs to secure the AM
antenna wires.
L
C
R
3
Fix the AM loop antenna to the attached stand.
To fix the stand to the antenna, bend in the direction
indicated by the arrow (fig. a) then clip the loop onto the
stand (fig. b).
• If you plan to mount the AM antenna to a wall or other
surface, secure the stand with screws (fig. c) before
clipping the loop to the stand. Make sure the
reception is clear.
SL
SR
Surround
Surround
4
Place the AM antenna on a flat surface and in a
SBL
SBR
Surround back
direction giving the best reception.
• If you have two surround back speakers THX
recommends placing them together and the same
distance from your listening position for the following
THX modes: THX Select2 CINEMA, THX
5
Connect the FM wire antenna in the same way as
the AM loop antenna.
For best results, extend the FM antenna fully and fix to a
wall or door frame. Don’t drape loosely or leave coiled up.
MUSICMODE and THX GAMES MODE.
See also THX Audio Setting on page 42 to make the
settings that will give you the best sound experience
when using the Home THX modes (page 28).
20
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
03
Connecting external antennas
To improve FM reception connect an external FM
antenna to the FM UNBAL 75 Ω terminal.
Plugging in the receiver
Only plug in after you have connected all your
components to this receiver, including the speakers.
Caution
• Handle the power cord by the plug part. Do not pull
out the plug by tugging the cord, and never touch the
power cord when your hands are wet, as this could
cause a short circuit or electric shock. Do not place
the unit, a piece of furniture, or other object on the
power cord or pinch the cord in any other way. Never
make a knot in the cord or tie it with other cables. The
power cords should be routed so that they are not
likely to be stepped on. A damaged power cord can
cause a fire or give you an electric shock. Check the
power cord once in a while. If you find it damaged,
ask your nearest Pioneer authorized independent
service company for a replacement.
75 Ω coaxial cable
ANTENNA
FM UNBAL 75
Ω
AM LOOP
To improve AM reception, connect a 5 m to 6 m (15 ft. to
18 ft.) length of vinyl-coated wire to the AM LOOP
terminals without disconnecting the supplied AM loop
antenna.
• The receiver should be disconnected by removing the
mains plug from the wall socket when not in regular
use, e.g., when on vacation.
For the best possible reception, suspend horizontally
outdoors.
• Make sure the blue ꢀ STANDBY/ON light has gone
out before unplugging.
Outdoor antenna
•
Plug the power cord into a power outlet.
Indoor antenna
(vinyl-coated wire)
AC outlet
ANTENNA
5 m to 6 m
(15 ft. to 18 ft.)
Power supplied through this outlet is turned on and off by
the receiver’s power switch. Total electrical power
consumption of connected equipment should not exceed
100 W (0.8 A).
FM UNBAL 75
Ω
AM LOOP
Caution
• Do not connect a TV set, monitor, heater, or similar
appliance to this unit’s AC outlet.
• Do not connect appliances with high power
consumption to the AC outlet in order to avoid
overheating and fire risk. This can also cause the
receiver to malfunction.
• Since a subwoofer or power amplifier can exceed the
100 W maximum when playing sources at a high
volume, this type of equipment should not be
connected to the AC outlet.
21
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
04
Chapter 4:
Controls and displays
Front panel
1
2
3
4
5 6
7
8
9
10
-
AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX 1017TXV
PHASE
CONTROL
STANDBY/ON
DIGITAL PRECISION PROCESSING
PHASE
CONTROL
ACOUSTIC
EQ
LISTENING
MODE
SIGNAL
SB ch
MULTI CH
IN
DVD/LD
TV/SAT
DVR/VCR
1
DVR/VCR
2
VIDEO/GAME
CD
CD
-R/TAPE/MD
FM/AM
XM
SIRIUS
iPod
SELECT PROCESSING
MASTER
VOLUME
ENTER
MULTI JOG
-
S
VIDEO
VIDEO/GAME INPUT
AUDIO
MCACC
SETUP MIC
VIDEO
L
R
DIGITAL IN
PHONES
SYSTEM
SETUP
TUNING/
STATION
TUNER
EDIT
RETURN
TONE
SPEAKERS
MULTI JOG
11 12
18
13
21
14
15
16
17
19
20
SYSTEM
SETUP
TUNING/
STATION
TUNER
EDIT
RETURN
TONE
SPEAKERS
MULTI JOG
1
MULTI JOG dial
6
DIGITAL PRECISION PROCESSING indicator
Use the MULTI JOG dial to select various settings and
menu options.
Light to indicate digital processing (for example, it
disappears when listening through the multichannel
analog inputs).
2
ꢀ STANDBY/ON
Switches the receiver between on and standby. Power
indicator lights when the receiver is on.
7
Character display
See Display on page 24.
8
Remote sensor
3
PHASE CONTROL
Receives the signals from the remote control (see
Operating range of remote control unit on page 23).
Press to switch on/off Phase Control(page 10).
ACOUSTIC EQ
Press to select an Acoustic Calibration EQ setting
(page 30).
9
SIGNAL SELECT
Use to select an input signal (page 30).
LISTENING MODE
Use with the MULTI JOG dial to select the various
listening modes (page 27).
SB ch PROCESSING
Selects the surround back channel mode (page 30)
or virtual surround back mode (page 31).
MULTI CH IN
4
PHASE CONTROL indicator
Press to select the multichannel analog inputs
(page 48).
Lights when Phase Control is switched on (page 10).
5
MCACC indicator
10 MASTER VOLUME dial
11 ENTER
Lights when Acoustic Calibration EQ (page 37) is on
(Acoustic Calibration EQ is automatically set to on after
the Auto MCACC Setup (page 8) or Advanced EQ Setup
(page 38)).
22
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
04
12 PHONES jack
Use to connect headphones. When the headphones are
connected, there is no sound output from the speakers.
13 Input source buttons
Press to select an input source.
14 VIDEO/GAME INPUT
See Connecting a component to the front panel inputs on
page 17.
15 MCACC SETUP MIC jack
Use to connect the supplied microphone.
16 SYSTEM SETUP
Press to access the System Setup menu (see page 35).
17 RETURN
Press to confirm and exit the current menu screen.
18 TONE
Press this button to access the bass and treble controls,
which you can then adjust with the MULTI JOG dial
(page 32).
19 TUNING/STATION
Use to find radio frequencies and to select preset
stations (page 33).
20 TUNER EDIT
Use with the MULTI JOG dial to memorize and name
stations for recall (page 33).
21 SPEAKERS
Use to change the speaker system (page 48).
Operating range of remote control unit
The remote control may not work properly if:
• There are obstacles between the remote control and
the receiver’s remote sensor.
• Direct sunlight or fluorescent light is shining onto the
remote sensor.
• The receiver is located near a device that is emitting
infrared rays.
• The receiver is operated simultaneously with another
infrared remote control unit.
30
N
30
7 m (23 ft.)
23
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
04
Display
1
2
3
4
5
6
7
8
9
10
11
12
FULL BAND PHASE CONTROL
DIALOG E ATT OVER STEREO EON
MONO
TUNED RDS
2
DIGITAL
WMA9 Pro
DTS
AUTO
L
C
S
R
SL
SR
SOUND
S.RTRV
V.SB
dB
SBL SB SBR
LFE
DIGITAL
ANALOG
SR+
DVR
STREAM DIRECT
Neo : 6
THX ADV.SURROUND
STEREO
2
PRO LOGIC
STANDARD
AB
SP
SLEEP
13
14
15
16 17
18
1
SIGNAL indicators
10 DIALOG E
Light to indicate the currently selected input signal.
AUTO lights when the receiver is set to select the input
Lights when the Dialog Enhancement feature is switched
on (page 32).
signal automatically (page 30).
11 Master volume level
2
Program format indicators
12 SR+
These change according to which channels are active in
digital sources.
Lights when the SR+ mode is switched on (page 51).
13 STREAM DIRECT
L – Left front channel
Lights when the Stream Direct mode is selected
(page 30).
C – Center channel
R – Right front channel
SL – Left surround channel
S – Surround channel (mono)
SR – Right surround channel
SBL – Left surround back channel
SB – Surround back channel (mono)
SBR – Right surround back channel
LFE – Low frequency effects channel
14 Speaker indicators
Indicate the current speaker system, A and/or B (page 48)
.
15 Listening mode indicators
THX – Lights when a Home THX mode is selected.
ADV.SURROUND – Lights when an Advanced
Surround mode has been selected (page 28).
3
Digital format indicators
Light when a signal encoded in the corresponding format
is detected.
STEREO – Lights when the stereo mode is selected
(page 29).
4
S.RTRV
STANDARD – Lights when a Standard Surround
mode is switched on (see Listening in surround
sound on page 27).
Lights when the Sound Retriever is switched on (page 32)
.
5
SOUND
Lights when any of the Midnight, Loudness or tone
controls feature is selected (page 32).
16 SLEEP
Lights when the receiver is in sleep mode (page 55).
6
PHASE CONTROL
17 Matrix decoding format indicators
Lights when the Phase Control is switched on (page 10).
2PRO LOGIC IIx – This lights to indicate 2Pro
Logic II / 2Pro Logic IIx decoding (page 27).
7
OVER ATT
/
OVER lights to indicate that the level of an analog source
is too high. ATT lights when you use the attenuator
(ANALOG ATT) to reduce it.
Neo:6 – When one of the Neo:6 modes of the receiver
is on, this lights to indicate Neo:6 processing
(page 27).
8
V.SB
18 Character display
Displays various system information.
Lights during Virtual surround back processing (page 31)
.
9
TUNER indicators
TUNED – Lights when a broadcast is being received.
STEREO – Lights when a stereo FM broadcast is
being received in auto stereo mode.
MONO – Lights when the mono mode is set using
the MPX button.
24
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
Remote control
04
3
Input source buttons
Press to select control of other components (see
Controlling the rest of your system on page 57).
4
Number buttons and other receiver/component
SYSTEM OFF
SOURCE
INPUT
RECEIVER
SELECT
controls
12
13
1
2
Use the number buttons to directly select a radio
frequency (page 33) or the tracks on a CD, DVD, etc.
DISC (ENTER) can be used to enter commands for TV or
DTV, and also to select a disc in a multi-CD player.
Press RECEIVER first to access:
XM RADIO
DVD
SIRIUS
TV
DVR 2
DVR 1
TV CTRL
RECEIVER
SLEEP – Use to put the receiver in sleep mode and
select the amount of time before sleep (page 55).
CD-R/TAPE
3
4
CD
iPod
TUNER
SB ch
14
SLEEP
ANALOG
ATT
SB ch – Use to select the surround/virtual back
channel mode (page 30).
SR+
DIMMER
PHASE
MIDNIGHT/
LOUDNESS
ANALOG ATT – Attenuates (lowers) the level of an
analog input signal to prevent distortion (page 55).
DIALOG
E
S.RETRIEVER
D.ACCESS
CLASS
DISC
+10
SR+ – Switches the SR+ mode on/off (page 51).
ENTER
TOP MENU
MENU
DIMMER – Dims or brightens the display (page 56).
TUNE
5
6
ST
ST
T.EDIT
MIDNIGHT/LOUDNESS – Use Midnight when
listening to movie soundtracks at low volume. Use
Loudness to boost the bass and treble at low volume
(page 32).
ENTER
SETUP
GUIDE
RETURN
TUNE
BAND
TV CONTROL
INPUT
TV CH
TV VOL
VOL
15
16
7
8
SELECT
DIALOG E – Use to make dialog stand out when
watching TV or a movie (page 32).
ANT
REC
INFO
PHASE – Press to switch on/off Phase Control
(page 10).
MUTE
REC STOP JUKEBOX
MPX
AUDIO SUBTITLE
DISP
HDD
CH
DVD
CH
S.RETRIEVER – Press to restore CD quality sound to
compressed audio sources (page 32).
PHOTO
STEREO/
F.S.SURR
THX
STANDARD ADV.SURR
9
10
11
Press TUNER first to access:
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
D.ACCESS – After pressing, you can access a radio
station directly using the number buttons (page 33).
SHIFT EFFECT/CH SEL
LEVEL
17
CLASS – Switches between the three banks (classes)
of radio station presets (page 33).
RECEIVER
5
Tuner/component control buttons/SETUP
These button controls can be accessed after you have
selected the corresponding input source button (DVD,
DVR1, TV, etc.). The BAND and T.EDIT tuner controls are
explained from page 33. Press RECEIVER first to access
the following controls:
The remote has been conveniently color-coded according
to component control using the following system (press
the corresponding input source button to access):
• Green – Receiver controls (see below)
• Red – DVD controls (page 60)
SETUP – Use to access the System Setup menu
(page 35).
• Blue – Tuner, XM and SIRIUS Radio controls
(page 33, page 44, page 46)
RETURN – Press to confirm and exit the current
menu screen (also use to return to the previous menu
with DVDs or to select closed captioning with DTV).
• Yellow – iPod controls (page 43)
• White – Other controls (page 60)
6
ꢂꢃꢁꢀ (TUNE/ST) /ENTER
1
RECEIVER
ꢀ
Use the arrow buttons when setting up your surround
sound system (page 35). Also used to control DVD
menus/options and for deck 1 of a double cassette deck
player. Use the TUNE ꢀ/ꢁ buttons to find radio
frequencies and use ST ꢂ/ꢃ to find preset stations
(page 33).
This switches between standby and on for this receiver.
2
INPUT SELECT
Use to select the input source (use SHIFT for INPUT
SELECT ).
25
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
04
7
TV CONTROL buttons
13 Character display (LCD)
These buttons are dedicated to control the TV assigned to
the TV CTRL button. Thus if you only have one TV to hook
up to this system assign it to the TV CTRL input source
button. If you have two TVs, assign the main TV to the TV
CTRL button (see page 57 for more on this).
This display shows information when transmitting
control signals.
The following commands are shown when you’re setting
the remote to control other components (see Controlling
the rest of your system on page 57):
TVꢀ – Use to turn on/off the power of the TV.
TV VOL +/– – Use to adjust the volume on your TV.
INPUT SELECT – Use to select the TV input signal.
TV CH +/– – Use to select channels.
SETUP – Indicates the setup mode, from which you
choose the options below.
PRESET – See Selecting preset codes directly on
page 57.
MULTI OP – See Multi Operation and System Off on
page 58.
8
Component control buttons
The main buttons (ꢁ, ꢂ, etc.) are used to control a
component after you have selected it using the input
source buttons.
SYS OFF – See Multi Operation and System Off on
page 58.
DIRECT F – See Direct function on page 57.
The controls above these buttons can be accessed after
you have selected the corresponding input source button
(for example DVD, DVR1 or TV). The following controls
can be accessed when listening to the built-in tuner:
RESET – See Resetting the remote control presets on
page 57.
READ ID – See Confirming preset codes on page 57.
MPX – Switches between stereo and mono reception
of FM broadcasts. If the signal is weak then switching
to mono will improve the sound quality (page 33).
14 RECEIVER
Switches the remote to control the receiver (used to
select the green commands above the number buttons
(ANALOG ATT, etc.)). Also use this button to set up
surround sound (page 8, page 35).
DISP – Switches between named station presets and
radio frequencies (page 34).
9
Receiver controls
THX – Press to select a Home THX listening mode
(page 28).
15 VOL +/–
Use to set the listening volume.
16 MUTE
STANDARD – Press for Standard decoding and to
switch between the various 2Pro Logic IIx and
Neo:6 options (page 27).
Mutes the sound or restores the sound if it has been
muted (adjusting the volume also restores the sound).
17 EFFECT/CH SEL and LEVEL +/–
ADV.SURR – Use to switch between the various
surround modes (page 28).
Press repeatedly to select a channel, then use +/– to
adjust the level (see Tip on page 41). Also adjusts the
level of the Advanced Surround effects, the Dolby Pro
Logic IIx Music and Neo:6 Music parameters and the
sound delay setting (page 29). You can then use the
+/– buttons to make these adjustments.
STEREO/F.S.SURR – Switches between the stereo
playback mode (page 29) and the Front Stage
Surround Advance mode (page 29).
AUTO SURR – Press to select the Auto Surround
mode (page 27) or the Stream Direct mode (page 30).
Stream Direct playback bypasses the tone controls
and any other signal processing for the most
accurate reproduction of a source (page 30).
ACOUSTIC EQ – Press to select an Acoustic
Calibration EQ setting (page 30).
SIGNAL SEL – Use to select an input signal (page 30).
10 MULTI OPE
Use this button to perform multi operations (page 58).
11 SHIFT
Press to access the controls outlined in white boxes (for
example, INPUT SELECT
), or to display the currently
selected input source in the remote control LCD.
12 SOURCEꢀ
Press to turn on/off other components connected to the
receiver (see page 57 for more on this).
26
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
05
Chapter 5:
Listening to your system
Important
Listening in surround sound
• The listening modes and many features described in
this section may not be available depending on the
current source (for example, PCM 88.2 kHz/96 kHz,
DTS 96 kHz (24 bit) or WMA9 Pro), settings and status
of the receiver. See Listening modes with different
input signal formats on page 70 for more on this.
Using this receiver, you can listen to any source in
surround sound. However, the options available will
depend on your speaker setup and the type of source
you’re listening to.
If you connected surround back speakers, see also Using
surround back channel processing on page 30.
Standard surround sound
Tip
The following modes provide basic surround sound for
• The listening modes described below can also be
selected using the front panel controls. Simply press
LISTENING MODE repeatedly to access the modes
you want, then use the MULTI JOG to select a
particular listening mode (after five seconds the
mode is automatically set).
3
stereo and multichannel sources.
PHOTO
STEREO/
THX
STANDARD ADV.SURR
F.S.SURR
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
SHIFT EFFECT/CH SEL
LEVEL
RECEIVER
Auto playback
•
While listening to a source, press STANDARD.
There are many ways to listen back to sources using this
receiver, but for the simplest, most direct listening option
is the Auto Surround feature. The receiver automatically
detects what kind of source you’re playing and selects
If necessary, press repeatedly to select a listening mode.
• If the source is Dolby Digital, DTS, or Dolby Surround
encoded, the proper decoding format will
automatically be selected and shows in the display.
1
4
multichannel or stereo playback as necessary.
PHOTO
STEREO/
THX
STANDARD ADV.SURR
F.S.SURR
With two channel sources, you can select from:
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
• 2Pro Logic IIx MOVIE – Up to 7.1 channel sound,
especially suited to movie sources
SHIFT EFFECT/CH SEL
LEVEL
• 2Pro Logic IIx MUSIC – Up to 7.1 channel sound,
5
RECEIVER
especially suited to music sources
• 2Pro Logic IIx GAME – Up to 7.1 channel sound,
especially suited to video games
•
While listening to a source, press AUTO SURR for
2
auto playback of a source.
• 2PRO LOGIC – 4.1 channel surround sound (sound
from the surround speakers is mono)
AUTO SURROUND shows briefly in the display before
showing the decoding or playback format. Check the
digital format indicators in the front panel display to see
how the source is being processed.
• Neo:6 CINEMA – 6.1 channel sound, especially
suited to movie sources
• Neo:6 MUSIC – 6.1 channel sound, especially suited
• When listening to XM Radio, the XM HD Surround
feature is selected automatically (see Using XM HD
Surround on page 45 for more on this).
6
to music sources
With multichannel sources, if you have connected
surround back speaker(s) and have selected SBch ON, you
can select (according to format):
Note
1 • Stereo surround (matrix) formats are decoded accordingly using Neo:6 CINEMA or 2Pro Logic IIx MOVIE (see Listening in surround sound above
for more on these decoding formats).
• The Auto Surround feature is canceled if you connect headphones or select the multichannel analog inputs.
2 For more options using this button, see Using Stream Direct on page 30.
3 In modes that give 6.1 channel sound, the same signal is heard from both surround back speakers.
4 If surround back channel processing (page 30) is switched OFF, or the surround back speakers are set to NO (this happens automatically if the Surround
back speaker setting on page 35 is set to anything but Normal (SB)), 2Pro Logic IIx becomes 2Pro Logic II (5.1 channel sound).
5 When listening to 2-channel sources in Dolby Pro Logic IIx Music mode, there are three further parameters you can adjust: Center Width, Dimension,
and Panorama. See Setting the effect options on page 29 to adjust them.
6 When listening to 2-channel sources in Neo:6 Music mode, you can also adjust the center image effect (see Setting the effect options on page 29).
27
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
05
• 2Pro Logic IIx MOVIE – See above (only available
when you’re using two surround back speakers)
• THX Surround EX – Allows you to hear 6.1 or 7.1
channel playback with 5.1 channel sources
• 2Pro Logic IIx MUSIC – See above
• THX Select2 CINEMA – Allows you to hear 7.1
channel playback with 5.1 channel sources
• Dolby Digital EX – Creates surround back channel
sound for 5.1 channel sources and provides pure
decoding for 6.1 channel sources (like Dolby Digital
Surround EX)
• THX MUSICMODE – Allows you to hear 7.1 channel
playback with 5.1 channel sources
• THX GAMES MODE – Allows you to hear 7.1 channel
• DTS-ES – Allows you to hear 6.1 channel playback
playback from the output of a video game console
with DTS-ES encoded sources
Using the Advanced surround effects
The Advanced surround effects can be used for a variety
of additional surround sound effects. Most Advanced
Surround modes are designed to be used with film
soundtracks, but some modes are also suited for music
sources. Try different settings with various soundtracks
to see which you like.
• DTS Neo:6 – Allows you to hear 6.1 channel playback
with DTS encoded sources
Using the Home THX modes
THX and Home THX are technical standards created by
THX Ltd. for cinema and home theater sound. Home THX
is designed to make home theater audio sound more like
what you hear in a cinema.
PHOTO
STEREO/
THX
STANDARD ADV.SURR
F.S.SURR
Different THX options will be available depending on the
source and the setting for surround back channel
processing (see Using surround back channel processing
on page 30 for more on this).
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
SHIFT EFFECT/CH SEL
LEVEL
RECEIVER
PHOTO
STEREO/
THX
STANDARD ADV.SURR
F.S.SURR
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
•
Press ADV.SURR repeatedly to select a listening
SHIFT EFFECT/CH SEL
LEVEL
3
mode.
• ACTION – Designed for action movies with dynamic
soundtracks
RECEIVER
• DRAMA – Designed for movies with lots of dialog
1
•
Press THX
(HOME THX) to select a listening mode.
• MONOFILM – Creates surround sound from mono
With two channel sources, press THX repeatedly to select
a matrix-decoding process for the THX CINEMA mode
(see Listening in surround sound above for an
explanation of each process):
soundtracks
• ENT. SHOW – Suitable for musical sources
4
• EXPANDED – Creates an extra wide stereo field
• TV SURROUND – Provides surround sound for both
mono and stereo TV sources
• 2Pro Logic IIx MOVIE+THX
• 2PRO LOGIC+THX
• ADVANCED GAME – Suitable for video games
• Neo:6 CINEMA+THX
• THX GAMES MODE
• SPORTS – Suitable for sports programs
• ROCK/POP – Creates a live concert sound for rock
and/or pop music
With multichannel sources, press THX
(HOME THX
)
2
repeatedly to select from:
• UNPLUGGED – Suitable for acoustic music sources
• THX CINEMA – Gives you cinema-quality sound from
your home theatre system using all the speakers in
your setup
• ExtendedSTEREO – Gives multichannel sound to a
stereo source, using all of your speakers
• PhonesSurround – Creates the effect of overall
surround with headphones.
• 2Pro Logic IIx MOVIE+THX – Especially suited to
movie sources, this allows you to hear 7.1 channel
playback with 5.1 channel sources
Note
1 You can’t use the THX modes when headphones are connected.
2 If you only have one surround back speaker connected, 2Pro Logic IIx MOVIE+THX, THX Select2 CINEMA, THX MUSICMODE and THX GAMES
MODE are not available.
3 • Depending on the source and the sound mode you have selected, you may not get sound from the surround back speakers in your setup. For more on
this, refer to Using surround back channel processing on page 30.
• If you press ADV.SURR when the headphones are connected, the PhonesSurround mode will automatically be selected.
4 Use with Dolby Pro Logic for a stereo surround effect (stereo field is wider than Standard modes with Dolby Digital sources).
28
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
05
PHOTO
STEREO/
F.S.SURR
THX
STANDARD ADV.SURR
Setting the effect options
When using surround effects, there are a number of
settings you can adjust.
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
SHIFT EFFECT/CH SEL
LEVEL
1
Press EFFECT/CH SEL repeatedly to select the
setting you want to adjust.
RECEIVER
Depending on the current status / mode of the receiver,
certain options may not appear. Check the table below for
notes on this.
•
While listening to a source, pressSTEREO/F.S.SURR
for stereo playback.
Press repeatedly to switch between:
2
Use the LEVEL +/– buttons to set it as necessary.
See the table below for the options available for each
setting. The defaults, if not stated, are listed in bold.
• STEREO – The audio is heard with your surround
settings and you can still use the Midnight,
Loudness, and Tone functions.
3
Press EFFECT/CH SEL again to adjust other
• F.S.SURR FOCUS – See Using Front Stage Surround
Advance below for more on this.
settings
.
Setting
What it does
Options
• F.S.SURR WIDE – See Using Front Stage Surround
Advance below for more on this.
Center
Widtha
(Applicableonly
Spreads the center channel between
the front right and left speakers,
making it sound wider (higher
0 to 7
Default: 3
settings) or narrower (lower settings).
when using a
Using Front Stage Surround Advance
center speaker)
The Front Stage Surround Advance function allows you to
create natural surround sound effects using just the front
speakers and the subwoofer.
Dimensiona
Adjusts the surround sound balance
from front to back, making the sound
more distant (minus settings), or
more forward (positive settings).
–3 to +3
Default: 0
PHOTO
STEREO/
THX
STANDARD ADV.SURR
F.S.SURR
a
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
Extends the front stereo image to
include surround speakers for a
‘wraparound’ effect.
OFF
Panorama
SHIFT EFFECT/CH SEL
LEVEL
ON
Center
Adjusts the center image to create a
wider stereo effect with vocals.
Adjust the effect from 0 (all center
channel sent to front right and left
speakers) to 10 (center channel sent
to the center speaker only).
0 to 10
Default: 3
RECEIVER
Imageb
(Applicable
only when
using a center
speaker)
•
While listening to a source, pressSTEREO/F.S.SURR
to select Front Stage Surround Advance modes.
• STEREO – See Listening in stereo above for more on
this.
Effect
Sets the effect level for the currently
selected Advanced Surround mode
(each mode can be set separately).
10 to 90
• F.S.SURR FOCUS – Use to provide a rich surround
sound effect directed to the center of where the front
left and right speakers sound projection area
converges.
Sound Delay Some monitors have a slight delay
0.0 to 6.0
(frames)
when showing video, so the
soundtrack will be slightly out of sync 1 second =
with the picture. By adding a bit of
delay, you can adjust the sound to
match the presentation of the video.
• F.S.SURR WIDE – Use to provide a surround sound
effect to a wider area than FOCUS mode.
30 frames
(NTSC)
1
FOCUS position (Recommend)
WIDE position
a.Only available with 2 ch sources in Dolby Pro Logic II Music / Dolby Pro
Logic IIx Music mode.
b.Only available with 2 ch sources in Neo:6 Music mode.
Front left
speaker
Front right
speaker
Front left
speaker
Front right
speaker
Listening in stereo
When you select STEREO, you will hear the source
through just the front left and right speakers (and
possibly your subwoofer depending on your speaker
settings). Dolby Digital, DTS and WMA9 Pro
multichannel sources are downmixed to stereo.
Note
1 When using F.S.SURR WIDE, a better effect can be obtained if Auto MCACC Setup is performed. For more on this, refer to Automatically setting up for
surround sound (Auto MCACC) on page 8.
29
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
Using Stream Direct
05
• EQ OFF – Switches Acoustic Calibration EQ off.
The MCACC indicator on the front panel lights when
2
Acoustic Calibration EQ is active.
Use the Stream Direct modes when you want to hear the
truest possible reproduction of a source. All unnecessary
signal processing is bypassed.
PHOTO
STEREO/
Choosing the input signal
THX
STANDARD ADV.SURR
F.S.SURR
You need to hook up a component to both analog and
digital inputs on the receiver to select between input
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
SHIFT EFFECT/CH SEL
LEVEL
3
signals.
PHOTO
STEREO/
THX
STANDARD ADV.SURR
F.S.SURR
RECEIVER
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
SHIFT EFFECT/CH SEL
LEVEL
•
While listening to a source, press AUTO SURR to
select the Stream Direct mode.
• AUTO SURROUND – See Auto playback on page 27.
RECEIVER
• STREAM DIRECT – Sources are heard according to
the settings made in the Surround Setup (Speaker
Setting, Channel Level, Speaker Distance), as well as
with dual mono, Center Width, Dimension and
Panorama settings. You will hear sources according
to the number of channels in the signal. For analog
sources, only Channel Level can be set. All other
digital processing can not be set.
•
Press SIGNAL SEL (SIGNAL SELECT) to select the
input signal corresponding to the source component.
Each press cycles through the options as follows:
• AUTO – This is the default setting. The receiver
selects the first available signal in the following order:
DIGITAL; ANALOG.
• ANALOG – Selects an analog signal.
• DIGITAL – Selects an optical or coaxial digital signal.
Listening with Acoustic Calibration EQ
When set to DIGITAL or AUTO, 2DIGITAL lights with
Dolby Digital decoding, DTS lights with DTS decoding,
and WMA9 Pro lights to indicate decoding of a WMA9
Pro signal.
• Default setting: OFF / ALL CH ADJUST (after the Auto
MCACC Setup or Advanced EQ Setup)
You can listen to sources using the Acoustic Calibration
Equalization set in Automatically setting up for surround
sound (Auto MCACC) on page 8 or Professional Acoustic
Calibration EQ on page 37. Refer to these pages for more
on Acoustic Calibration Equalization.
Using surround back channel processing
• Default setting: SBch ON
PHOTO
STEREO/
You can have the receiver automatically use 6.1 or 7.1
decoding for 6.1 encoded sources (for example, Dolby
Digital EX or DTS-ES), or you can choose to always use
6.1 or 7.1 decoding (for example, with 5.1 encoded
material). With 5.1 encoded sources, a surround back
channel will be generated, but the material may sound
better in the 5.1 format for which it was originally
encoded (in which case, you can simply switch surround
back channel processing off).
THX
STANDARD ADV.SURR
F.S.SURR
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
SHIFT EFFECT/CH SEL
LEVEL
RECEIVER
•
While listening to a source, press ACOUSTIC EQ.
Press repeatedly to select between:
• ALL CH ADJUST – A ‘flat’ setting where all the
speakers are heard individually.
• FRONT ALIGN – All speakers are heard in
accordance with the front speaker settings.
1
• CUSTOM 1/2 – Custom settings
Note
1 When TYPE2 is not selected in the Auto MCACC setup or the Advanced EQ setup in the Manual MCACC setup, the EQ value cannot be set for FRONT
ALIGN.
2 You can’t use Acoustic Calibration EQ with MULTI CH IN, XM HD Surround, Stream Direct or WMA9 Pro, and it has no effect with headphones.
3 • This receiver can only play back Dolby Digital, PCM (32 kHz to 96 kHz), DTS (including DTS 96 kHz/24 bit) and WMA9 Pro digital signal formats. With
other digital signal formats, set to ANALOG (the MULTI CH IN and TUNER functions are all fixed to ANALOG).
• You may get digital noise when a LD or CD player compatible with DTS is playing an analog signal. To prevent noise, make the proper digital
connections (page 16) and set the signal input to DIGITAL.
• Some DVD players don’t output DTS signals. For more details, refer to the instruction manual supplied with your DVD player.
30
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
05
The table below indicates when you will hear the
surround back channel when playing various kinds of
sources (ì=Sound plays through surround back
speaker(s)).
Using the Virtual Surround Back mode
When you’re not using surround back speakers,
selecting this mode allows you to hear a virtual surround
back channel through your surround speakers. You can
choose to listen to sources with no surround back
channel information, or if the material sounds better in
the format (for example, 5.1) for which it was originally
encoded, you can have the receiver only apply this effect
XM RADIO
DVD
SIRIUS
TV
DVR
2
DVR 1
TV CTRL
CD-R/TAPE
CD
iPod
TUNER
SB ch
RECEIVER
SLEEP
ANALOG
ATT
1
SR+
DIMMER
PHASE
MIDNIGHT/
LOUDNESS
to 6.1 encoded sources like Dolby Digital EX or DTS-ES.
DIALOG
E
S.RETRIEVER
The table indicates when you will hear the virtual
surround back channel (ì=Virtual surround back
channel is active).
•
Press RECEIVER then press SB ch (SB ch
PROCESSING) repeatedly to cycle the surround back
channel options.
Each press cycles through the options as follows:
•
Press RECEIVER then press SB ch (SB ch
PROCESSING) repeatedly to cycle the virtual surround
back channel options.
Each press cycles through the options as follows:
• SBch ON – 6.1 or 7.1 decoding is always used (for
example, a surround back channel will be generated
for 5.1 encoded material)
• VirtualSB ON – Virtual Surround Back is always used
(for example, on 5.1 encoded material)
• SBch AUTO – Automatically switches to 6.1 or 7.1
decoding for 6.1 encoded sources (for example,
Dolby Digital EX or DTS-ES)
• VirtualSB AUTO – Virtual Surround Back is
automatically applied to 6.1 encoded sources (for
example, Dolby Digital EX or DTS-ES)
• SBch OFF – Maximum 5.1 playback
• VirtualSB OFF – Virtual Surround Back mode is
switched off
Standard / THX
SBch
Processing /
Virtual SB
mode
Advanced
Type of source
Stereo sources
surround
Multichannel
sources
2Pro Logic IIx
2Pro Logic
Neo:6
b
b
b
b
b
b
Dolby Digital EX/DTS-ES/WMA9 Pro encoded
multichannel sources with 6.1ch surround
ON
AUTO
ON
ì
ì
ì
ì
ì
ì
ì
ì
ì
Dolby Digital/DTS/WMA9 Pro encoded
multichannel sources
AUTO
ON
a,b
Dolby Digital/DTS/PCM/WMA9 Pro encoded
stereo sources
ì
ì
ì
ì
ì
ì
c
AUTO
ON
ì
a
Analog 2-channel (stereo) sources
ì
ì
ì
ì
c
AUTO
ì
a. Only applicable when using the Virtual Surround Back mode.
b.Excluding the WMA9 Pro format.
c. Not applicable when using the Virtual Surround Back mode.
Note
1 • You can’t use the Virtual Surround Back mode when the headphones are connected to this receiver or when any of the THX, XM HD Surround, stereo,
Front Stage Surround Advance or Stream Direct mode is selected.
• You can only use the Virtual Surround Back mode if the surround speakers are on and the Surr Back setting is set to NO in the Speaker Setting on
page 40.
• Depending on the input signal and the listening mode, the Virtual Surround Back mode may not be effective.
31
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
05
Using Midnight and Loudness
The Midnight listening feature allows you to hear
effective surround sound of movies at low volume levels.
The effect automatically adjusts according to the volume
at which you’re listening. The Loudness listening feature
can be used to get good bass and treble from music
sources at low volume levels.
•
Press RECEIVER then press MIDNIGHT/LOUDNESS
to switch between MIDNIGHT, LOUDNESS, and OFF.
Using the Sound Retriever
When audio data is removed during the WMA/MP3/
MPEG-4 AAC compression process, sound quality often
suffers from an uneven sound image. The Sound
Retriever feature employs new DSP technology that
helps bring CD quality sound back to compressed 2-
channel audio by restoring sound pressure and
smoothing jagged artifacts left over after compression.
•
Press RECEIVER then press S.RETRIEVER (SOUND
RETRIEVER) to switch the sound retriever on or off.
Enhancing dialog
• Default setting: OFF
The Dialog Enhancement feature localizes dialog in the
center channel to make it stand out from other
background sounds in a TV or movie soundtrack.
•
Press RECEIVER then press DIALOG E to switch
dialog enhancement on or off.
Using the tone controls
Depending on what you are listening to, you may want to
adjust the bass or treble using the front panel tone
1
control.
1
Press TONE to select the frequency you want to
adjust.
Press to switch between BASS and TREBLE.
2
Use the MULTI JOG dial to change the amount of
bass or treble as necessary.
The bass and treble can be adjusted from –6 to +6 (dB).
• Wait about five seconds for your changes to be input
automatically.
Note
1 The tone controls are only available when the stereo mode or the Front Stage Surround Advance mode is selected (except when STEREO is selected
using AUTO SURROUND).
32
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the tuner
06
Chapter 6:
Using the tuner
Tuning directly to a station
Sometimes, you’ll already know the frequency of the
station you want to listen to. In this case, you can simply
enter the frequency directly using the number buttons on
the remote control.
Listening to the radio
The following steps show you how to tune in to FM and
AM radio broadcasts using the automatic (search) and
manual (step) tuning functions. If you already know the
frequency of the station you want, see Tuning directly to a
station below. Once you are tuned to a station you can
memorize the frequency for recall later—see Saving
station presets on page 33 for more on how to do this.
1
Press the TUNER button to select the tuner.
2
Use the BAND button to change the band (FM or
AM), if necessary.
Each press switches the band between FM and AM.
SYSTEM OFF
SOURCE
INPUT
RECEIVER
3
Press D.ACCESS (Direct Access).
DIALOG
+10
E
PHASE
S.RETRIEVER
DISC
SELECT
ANT
REC
INFO
MUTE
REC STOP JUKEBOX
D.ACCESS
CLASS
ENTER
MPX
4
Use the number buttons to enter the frequency of
TOP MENU
MENU
AUDIO SUBTITLE
DISP
HDD
CH
DVD
CH
the radio station.
For example, to tune to 106.00 (FM), press 1, 0, 6, 0, 0.
TUNE
PHOTO
ST
ST
T.EDIT
STEREO/
F.S.SURR
THX
STANDARD ADV.SURR
ENTER
SETUP
GUIDE
RETURN
XM RADIO
DVD
SIRIUS
TV
DVR
2
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
TUNE
BAND
DVR
1
TV CTRL
RECEIVER
If you make a mistake halfway through, press D.ACCESS
twice to cancel the frequency and start over.
TV CONTROL
SHIFT EFFECT/CH SEL
LEVEL
CD-R/TAPE
CD
iPod
TUNER
INPUT
TV VOL
TV CH
VOL
SELECT
1
2
Press the TUNER button to select the tuner.
Saving station presets
Use the BAND button to change the band (FM or
AM), if necessary.
Each press switches the band between FM and AM.
If you often listen to a particular radio station, it’s
convenient to have the receiver store the frequency for
easy recall whenever you want to listen to that station.
This saves the effort of manually tuning in each time. This
receiver can memorize up to 30 stations, stored in three
banks, or classes (A, B and C) of 10 stations each. When
saving an FM frequency, the MPX setting (see page 33) is
also stored.
3
Tune to a station.
There are three ways to do this:
Automatic tuning
To search for stations in the currently selected band,
press and hold TUNE ꢀ/ꢁ for about a second. The
receiver will start searching for the next station,
stopping when it has found one. Repeat to search for
other stations.
SYSTEM OFF
INPUT
RECEIVER
SOURCE
S.RETRIEVER
DISC
DIALOG
+10
E
PHASE
SELECT
ANT
REC
INFO
MUTE
REC STOP JUKEBOX
D.ACCESS
CLASS
ENTER
MPX
TOP MENU
MENU
AUDIO SUBTITLE
DISP
HDD
CH
DVD
CH
Manual tuning
To change the frequency one step at a time, press
TUNE ꢀ/ꢁ.
TUNE
PHOTO
ST
ST
STEREO/
F.S.SURR
T.EDIT
THX
STANDARD ADV.SURR
ENTER
SETUP
GUIDE
RETURN
XM RADIO
DVD
SIRIUS
TV
DVR
2
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
TUNE
BAND
DVR
1
TV CTRL
RECEIVER
TV CONTROL
SHIFT EFFECT/CH SEL
LEVEL
CD-R/TAPE
CD
iPod
TUNER
INPUT
High speed tuning
TV VOL
TV CH
VOL
SELECT
Press and hold TUNE ꢀ/ꢁ for high speed tuning.
Release the button at the frequency you want.
1
Tune to a station you want to memorize.
See Listening to the radio on page 33 for more on this.
Improving FM stereo sound
2
Press T.EDIT (TUNER EDIT).
If the TUNED or STEREO indicators don’t light when
tuning to an FM station because the signal is weak, press
the MPX button to switch the receiver into mono
reception mode. This should improve the sound quality
and allow you to enjoy the broadcast.
The display shows STATION MEMORY, then a blinking
memory class.
3
Press CLASS to select one of the three classes then
press ST ꢂ/ꢃ to select the station preset you want.
You can also use the number buttons to select a station
preset.
4
Press ENTER.
After pressing ENTER, the preset class and number stop
blinking and the receiver stores the station.
33
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the tuner
06
Naming station presets
For easier identification, you can name your station
presets.
1
Choose the station preset you want to name.
See Listening to station presets below for how to do this.
2
Press T.EDIT (TUNER EDIT).
The display shows STATION NAME, then a blinking
cursor at the first character position.
3
Input the name you want.
Choose from the following characters for a name up to
four characters long.
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
0123456789
!”#$%&’()∗+,–./:;<=>?@[ \ ]^_{|} ˜ [space]
• Use the ST ꢂ/ꢃ buttons (remote) to select
characters.
• Press ENTER to confirm a character. If no character
is input, a space is input.
• The name is stored when ENTER is pressed after
choosing the fourth character.
Tip
• To erase a station name, simply repeat steps 1 to 3
and input four spaces instead of a name.
• Once you have named a station preset, you can press
DISP when listening to a station to switch the display
between name and frequency.
Listening to station presets
You will need to have some presets stored to do this. See
Saving station presets above if you haven’t done this
already.
1
Press TUNER to select the tuner.
2
Press CLASS to select the class in which the station
is stored.
Press repeatedly to cycle through classes A, B and C.
3
Press ST ꢂ/ꢃ to select the station preset you
want.
• You can also use the number buttons on the remote
control to recall the station preset.
34
En
Download from Www.Somanuals.com. All Manuals Search And Download.
The System Setup menu
07
Chapter 7:
The System Setup menu
• Manual MCACC – Fine tune your speaker settings
and customize the Acoustic Calibration EQ (see
Manual MCACC setup on page 36).
Making receiver settings from the
System Setup menu
• Manual SP Setup – Specify the size, number,
distance and overall balance of the speakers you’ve
connected (see Manual speaker setup on page 40).
The following section shows you how to make detailed
settings to specify how you’re using the receiver (for
example, if you want to set up two speaker systems in
separate rooms), and also explains how to fine-tune
individual speaker system settings to your liking.
• Input Assign – Specify what you’ve connected to the
digital, component video and HDMI inputs (see The
Input Assign menu on page 52).
DIALOG
E
PHASE
S.RETRIEVER
• Other Setup – Make customized settings to reflect
how you are using the receiver (see The Other Setup
menu on page 53).
SYSTEM OFF
SOURCE
INPUT
RECEIVER
SELECT
D.ACCESS
CLASS
ENTER
+10
DISC
TOP MENU
MENU
TUNE
ST
ST
T.EDIT
ENTER
SETUP
GUIDE
RETURN
TUNE
BAND
XM RADIO
DVD
SIRIUS
TV
DVR
2
TV CONTROL
Surround back speaker setting
DVR 1
TV CTRL
RECEIVER
INPUT
TV VOL
TV CH
VOL
CD-R/TAPE
CD
SELECT
• Default setting: Normal (SB)
iPod
TUNER
There are several ways you can use the surround back
speaker channels with this system. In addition to a
normal home theater setup where they are used for the
surround back speakers, they can be used for bi-amping
the front speakers or as a separate speaker system in
another room.
1
Switch on the receiver and your TV.
1
Use the ꢀ RECEIVER button to switch on.
• If headphones are connected to the receiver,
disconnect them.
2
Press RECEIVER on the remote control, then press
1
Select ‘Surr Back System’ from the System Setup
2
menu.
the SETUP button.
See Making receiver settings from the System Setup menu
above if you’re not already at this screen.
An on-screen display (OSD) appears on your TV. Use ꢀ/
ꢁ/ꢂ/ꢃ and ENTER to navigate through the screens
and select menu items. Press RETURN to confirm and
exit the current menu.
System Setup
1.Surr Back System
1.Surround Back System
Surr Back System
Normal (SB)
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
]
• Press SETUP at any time to exit the System Setup
menu.
3
Select the setting you want to adjust.
:
Exit
:
Finish
System Setup
2
Select the surround back speaker setting.
• Normal (SB) – Select for normal home theater use
with surround back speakers in your main (speaker
system A) setup.
1.Surr Back System
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
:
Exit
• Speaker B – Select to use the (surround back) B
speaker terminals to listen to stereo playback in
another room (see Speaker B setup on page 48).
• Surr Back System – Specify how you are using your
surround back speakers (see Surround back speaker
setting below).
• Front Bi-Amp – Select this setting if you’re bi-
amping your front speakers (see Bi-amping your front
speakers on page 49).
• Auto MCACC – This is a quick and effective
automatic surround setup (see Automatically setting
up for surround sound (Auto MCACC) on page 8).
3
When you’re finished, press RETURN.
You return to the System Setup menu.
Note
1 Make sure not to switch off the power when using the System Setup menu.
2 • The OSD will not appear if you have connected using the HDMI output to your TV. Use component, S-video, or composite connections for system setup.
• You can’t use the System Setup menu when the iPod, XM or SIRIUS Radio input source is selected.
35
En
Download from Www.Somanuals.com. All Manuals Search And Download.
The System Setup menu
Manual MCACC setup
07
• EQ Data Copy – Copy Acoustic Calibration EQ
settings for manual adjustment (see Copying your
Acoustic Calibration EQ settings on page 38).
• EQ CUSTOM1/2 Adjust – Make detailed manual
adjustments to your custom Acoustic Calibration EQ
settings (see Setting the Acoustic Calibration EQ
manually on page 39).
You can use the settings in the Manual MCACC setup
menu to make detailed adjustments when you’re more
familiar with the system. Before making these settings,
you should have already completed Automatically setting
up for surround sound (Auto MCACC) on page 8.
• EQ Data Check – Check the ALL CH ADJUST,
FRONT ALIGN and custom settings using the on-
screen display (see Checking your Acoustic
Calibration EQ settings on page 39).
You only need to make these settings once (unless you
change the placement of your current speaker system or
add new speakers).
Important
Fine Channel Level
• For some of the settings below, you’ll have to connect
the setup microphone to the front panel and place it
about ear level at your normal listening position.
Press SETUP to display the System Setup menu
before you connect the microphone to this receiver. If
the microphone is connected while the System Setup
menu is not being displayed, the display will change
to the Auto MCACC setup menu. See Problems when
using the Auto MCACC Setup on page 10 for notes
regarding background noise and other possible
interference.
• Default setting: 0.0dB (all channels)
You can achieve better surround sound by properly
adjusting the overall balance of your speaker system. The
following setting can help you make detailed
adjustments that you may not achieve using the Manual
speaker setup on page 40.
1
Select ‘Fine Ch Level’ from the Manual MCACC
setup menu.
After the volume increases to the reference level, test
tones will be output.
• If you’re using a subwoofer, switch it on and turn up
the volume as necessary.
3a.Fine Channel Level
3.Manual MCACC
a.Fine Ch Level
b.Fine SP Distance
c.Advanced EQ Setup
d.EQ Data Copy
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
Please Wait... 20
Caution!
Loud test tones
will be output.
Caution
• The test tones used in the MCACC setup are output
at high volume.
:Cancel
:Return
1
Select ‘Manual MCACC’ from the System Setup
2
Adjust the level of the left channel, press ENTER.
menu.
This will be the reference speaker level, so you may want
to keep the level around 0dB so that you’ll have plenty of
room to adjust the other speaker levels.
See Making receiver settings from the System Setup menu
above if you’re not already at this screen.
System Setup
3.Manual MCACC
3a.Fine Channel Level
1.Surr Back System
a.Fine Ch Level
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
b.Fine SP Distance
c.Advanced EQ Setup
d.EQ Data Copy
MCACC:M1. MEMORY
1
L(Reference)
+0.5dB
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
:
Exit
:Return
Enter:Next
:Cancel
2
Select the setting you want to adjust.
3
Select each channel in turn and adjust the levels
If you’re doing this for the first time, you might want to
make these settings in order.
(+/–10dB) as necessary.
Use ꢂ/ꢃ to adjust the volume of the speaker you
selected to match the reference speaker.
• Fine Ch Level – Make fine adjustments to the overall
balance of your speaker system (see Fine Channel
Level below).
• Fine SP Distance – Make precise delay settings for
your speaker system (see Fine Speaker Distance on
page 37).
• Advanced EQ Setup – Calibrate your system based
on the direct sound coming from the speakers and
make detailed settings according to your room’s
reverb characteristics (see Setting the Acoustic
Calibration EQ automatically on page 38).
When it sounds like both tones are the same volume,
press ꢁ to confirm and continue to the next channel.
3a.Fine Channel Level
L
+
0.0dB (Reference)
R
[
0.0dB
1.0dB
-3.0dB
]
C
SL
SR
+
[
]
]
]
]
]
[+ 10.0dB
SBL [– 10.0dB
SBR [+ 9.5dB
SW
[– 1.5dB
:Finish
36
En
Download from Www.Somanuals.com. All Manuals Search And Download.
The System Setup menu
07
• For comparison purposes, the reference speaker will
change depending on which speaker you select.
Listen to the reference speaker and use it to measure the
target channel. From the listening position, face the two
speakers with your arms outstretched pointing at each
speaker. Try to make the two tones sound as if they are
arriving simultaneously at a position slightly in front of
• If you want to go back and adjust a channel, simply
use ꢀ/ꢁ to select it.
4
When you're finished, press RETURN.
You return to the Manual MCACC setup menu.
1
you and between your arm span.
Fine Speaker Distance
• Default setting: 10.0 ft. (3.0 m) (all channels)
For proper sound depth and separation with your system,
it is necessary to add a slight bit of delay to some
speakers so that all sounds will arrive at the listening
position at the same time. The following setting can help
you make detailed adjustments that you may not achieve
using the Manual speaker setup below.
When it sounds like the delay settings are matched up,
press ENTER to confirm and continue to the next
channel.
• For comparison purposes, the reference speaker will
change depending on which speaker you select.
1
Select ‘Fine SP Distance’ from the Manual MCACC
setup menu.
The volume increases to the reference level.
• If you want to go back and adjust a channel, simply
use ꢀ/ꢁ to select it.
3.Manual MCACC
4
When you're finished, press RETURN.
a.Fine Ch Level
b.Fine SP Distance
c.Advanced EQ Setup
d.EQ Data Copy
You return to the Manual MCACC setup menu.
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
Professional Acoustic Calibration EQ
Acoustic Calibration Equalization is a kind of speaker
equalizer. It works by measuring the acoustic
characteristics of your listening room and turning the
ambient environment into a natural state to reproduce
the source sound as it was originally recorded. This is an
equalizer that enables a ‘flat’ setting.
:Return
2
Adjust the distance of the left channel from the
listening position.
3b.Fine SP Distance
L(Reference)
10.0 ft
This setting minimizes the undesirable reverberation of
your listening room based on the sound directly coming
from the speakers. You can select a correction time
period during the automatic calibration.
ENTER:Next
:Cancel
After pressing ENTER, test tones will be output.
Select each channel in turn and adjust the
If you’re not satisfied with the automatic adjustment
provided in Automatically setting up for surround sound
(Auto MCACC) on page 8, you can also adjust these
settings manually to get a frequency balance that suits
your tastes.
3
distance as necessary.
Use ꢂ/ꢃto adjust the delay of the speaker you selected
to match the reference speaker. The delay is measured in
terms of speaker distance from 0.5 to 45.0 feet.
3b.Fine SP Distance
(
]
)
L
10.0ft Reference
R
[
9.0ft
9.5ft
6.0ft
6.5ft
6.0ft
6.5ft
C
SL
SR
SBL
SBR
SW
[
[
[
[
[
]
]
]
]
12.5ft ]
ꢃ:Finish
Note
1 If you can’t seem to achieve this by adjusting the distance setting, you may need to change the angle of your speakers very slightly.
37
En
Download from Www.Somanuals.com. All Manuals Search And Download.
The System Setup menu
07
For an optimal system calibration based on the direct
sound coming from the speakers, we recommend using
the 30~50ms setting.
Setting the Acoustic Calibration EQ automatically
When you perform the Auto MCACC setup as specified in
Automatically setting up for surround sound (Auto
MCACC) on page 8, the correction is automatically done
with the time period already selected (when TYPE1 is
selected for EQ TYPE, the calibration is set only for ALL
CH ADJUST). In this setup, you can select any of the time
periods for EQ correction.
3c.Advanced EQ Setup
TIME POSITION
30~50ms
ENTER
:
Start
:Cancel
1
Select ‘Advanced EQ Setup’ from the Manual
MCACC setup menu.
4
Press ENTER, then the calibration starts
automatically.
3.Manual MCACC
a.Fine Ch Level
b.Fine SP Distance
c.Advanced EQ Setup
d.EQ Data Copy
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
3c.Advanced EQ Setup
3c.Advanced EQ Setup
Please Wait... 20
Set microphone.
Turn on Subwoofer.
Caution!
Loud test tones
will be output.
:Return
:Cancel
:Cancel
• The Advanced EQ setup overwrites the settings
already set for ALL CH ADJUST and/or FRONT
ALIGN. To keep these settings intact, save the data in
CUSTOM1/CUSTOM2 as specified in Copying your
Acoustic Calibration EQ settings below.
5
Wait for the Advanced EQ Setup to finish.
3c.Advanced EQ Setup
Now Analyzing
3c.Advanced EQ Setup
Now Analyzing
• Make sure the supplied microphone is connected.
Environment Check
Ambient Noise
Microphone
Surround Analyzing
[
[
[
]
]
]
Delay Check
[
[
[
]
]
]
Level Check
Aco Cal EQ Pro.
• See Problems when using the Auto MCACC Setup on
page 10 for notes regarding high background noise
levels and other possible interference.
Speaker Level
:Cancel
:Cancel
As the receiver outputs test tones, the frequency balance
is adjusted automatically for the following settings:
2
Select ‘TYPE1’ or ‘TYPE2’.
3c.Advanced EQ Setup
EQ TYPE
TYPE1
3c.Advanced EQ Setup
EQ TYPE
TYPE2
• ALL CH ADJUST – A ‘flat’ setting where all the
speakers are set individually so no special weighting
is given to any one channel.
ALL CH ADJUST
ALL CH ADJUST
FRONT ALIGN
• FRONT ALIGN – All speakers are set in accordance
with the front speaker settings (no equalization is
applied to the front left and right channels).
ENTER
:
NEXT
:Cancel
ENTER
:
NEXT
:Cancel
Use ꢂ/ꢃ to select the setting.
It will take about 1 to 3 minutes for the calibration to
finish.
When TYPE1 is selected, the calibration is set for ALL CH
ADJUST; when TYPE2 is selected, the calibration is set
for both ALL CH ADJUST and FRONT ALIGN.
The display returns to the Manual MCACC setup menu
automatically after the Acoustic Calibration Equalization
is set.
3
Select the time setting you want to use for
1
calibration.
Copying your Acoustic Calibration EQ settings
If you want to manually adjust the Acoustic Calibration
EQ (see Setting the Acoustic Calibration EQ manually
below), we recommend copying the ALL CH ADJUST or
the FRONT ALIGN settings from the Advanced EQ Setup
above (or from Automatically setting up for surround
sound (Auto MCACC) on page 8) to one of the custom
settings. Instead of just a flat EQ curve, this will give you
a reference point from which to start.
You can choose the time period that will be used for the
calibration. Use ꢂ/ꢃ to select the time setting.
Select the setting from the following time periods (in
milliseconds): 0~20ms, 10~30ms, 20~40ms, 30~50ms,
40~60ms, 50~70ms and 60~80ms. This setting will be
applied to all channels during calibration.
Note
1 For multi-channel audio sources, the localization of the reproduced sound image and the sound linkage of the speakers depend on the direct sound
including the early-reflected sound. In this setup, the earlier time settings (0~20ms, 10~30ms, etc.) implement calibration closer to the direct sound with
less consideration of the reverb characteristics; the later time settings (60~80ms, 50~70ms, etc.) incorporate the reverberant sound. Select your favorite
setting for the optimum results.
38
En
Download from Www.Somanuals.com. All Manuals Search And Download.
The System Setup menu
07
1
Select ‘EQ Data Copy’ from the Manual MCACC
3
Select the channel(s) you want and adjust to your
setup menu.
liking.
3.Manual MCACC
3e.EQ CUSTOM1 Adjust
3e. EQ CUSTOM1 Adjust
a.Fine Ch Level
Test Tone Type:
"ALL CH ADJUST"
Left
Test Tone Type:
b.Fine SP Distance
c.Advanced EQ Setup
d.EQ Data Copy
"ALL CH ADJUST"
[
Left
40Hz
]
40Hz
125Hz
250Hz
4kHz
:
:
:
:
:
:
[+ 1.0dB
]
]
]
]
]
]
:
:
:
:
:
:
+
1.0dB
0.0dB
0.0dB
0.0dB
0.0dB
0.0dB
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
[
[
[
[
[
0.0dB
0.0dB
0.0dB
0.0dB
0.0dB
125Hz
250Hz
4kHz
13kHz
TRIM
[
[
[
[
[
]
]
]
]
]
13kHz
TRIM
:Return
:Finish
:Finish
2
Select CUSTOM1 or CUSTOM2 then use ꢂ/ꢃ to
Use ꢂ/ꢃ to select the channel.
select the setting you want to copy.
Use ꢀ/ꢁ to select the frequency and ꢂ/ꢃ to boost or
cut the EQ. When you’re finished, go back to the top of
the screen and use ꢂ/ꢃ to select the next channel.
3d.EQ Data Copy
3d.EQ Data Copy
TO
FROM
TO
FROM
CUSTOM1
CUSTOM2
CUSTOM1
CUSTOM2
CUSTOM1
CUSTOM2
ALL CH ADJ
CUSTOM2
• The front speakers can’t be adjusted if you selected
[
]
[
]
FRONT ALIGN.
Start Copy
[
OK
]
Start Copy
[
OK
]
• The OVER! indicator shows in the display if the
frequency adjustment is too drastic and might
distort. If this happens, bring the level down until
OVER! disappears from the display.
:Cancel
:Cancel
• You can also copy from one custom setting to
another. For more on the ALL CH ADJUST and
FRONT ALIGN settings, see Setting the Acoustic
Calibration EQ automatically above.
Tip
3
Select ‘OK’ to copy and confirm.
• Changing the frequency curve of one channel too
drastically will affect the overall balance. If the
speaker balance seems uneven, you can raise or
lower channel levels using test tones with the TRIM
feature. Use ꢀ/ꢁ to select TRIM then use ꢂ/ꢃ to
raise or lower the channel level for the current
speaker.
Setting the Acoustic Calibration EQ manually
Before manually adjusting the Acoustic Calibration EQ,
we recommend copying the ALL CH ADJUST or the
FRONT ALIGN settings from the auto setup above (or
from Automatically setting up for surround sound (Auto
MCACC) on page 8) to one of the custom settings.
Instead of just a flat EQ curve, this will give you a
reference point from which to start (see Copying your
Acoustic Calibration EQ settings above for how to do this).
4
When you're finished, press RETURN.
You return to the Manual MCACC setup menu.
Checking your Acoustic Calibration EQ settings
After you have completed an automatic or manual
Acoustic Calibration EQ adjustment, you can check the
ALL CH ADJUST, FRONT ALIGN and custom settings
using the on-screen display.
1
Select ‘EQ CUSTOM1 Adjust’ or ‘EQ CUSTOM2
Adjust’ from the Manual MCACC setup menu.
3e.EQ CUSTOM1 Adjust
3.Manual MCACC
a.Fine Ch Level
Test Tone Type
b.Fine SP Distance
c.Advanced EQ Setup
d.EQ Data Copy
ALL CH ADJUST
1
Select ‘EQ Data Check’ from the Manual MCACC
setup menu.
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
ENTER:Next
:Cancel
:Return
3.Manual MCACC
3g.EQ Data Check
ALL CH ADJUST
a.Fine Ch Level
b.Fine SP Distance
c.Advanced EQ Setup
d.EQ Data Copy
[
Left
]
2
Select which method you would like to use to
+
40Hz
:
:
:
:
:
:
1.0dB
0.0dB
0.0dB
0.0dB
0.0dB
0.0dB
e.EQ CUSTOM1 Adjust
f .EQ CUSTOM2 Adjust
g.EQ Data Check
125Hz
250Hz
4kHz
adjust the overall frequency balance.
It is best to choose whichever one you copied to the
custom setting in Copying your Acoustic Calibration EQ
settings above.
13kHz
TRIM
:Return
:Return
2
3
Select the setting you want to check.
• It is useful to do this while a source is playing so you
can compare the different settings.
• ALL CH ADJUST – All the speakers can be set
independently so no special weighting is given to any
one channel. When adjusting, test tones will sound
for each individual channel.
Select the channels you want, pressing ENTER
when you’re finished checking each one.
• FRONT ALIGN – Speakers are set in accordance with
the front speaker settings. The sound of the test tone
will alternate between the left front (reference)
speaker and the target speaker.
4
When you're finished, press RETURN.
You return to the Manual MCACC setup menu.
39
En
Download from Www.Somanuals.com. All Manuals Search And Download.
The System Setup menu
Manual speaker setup
07
1
Select ‘Speaker Setting’ from the Manual SP
Setup menu.
This receiver allows you to make detailed settings to
optimize the surround sound performance. You only need
to make these settings once (unless you change the
placement of your current speaker system or add new
speakers).
4a.Speaker Setting
4.Manual SP Setup
Front
Center
Surr
SMALL
SMALL ]
SMALL ]
SMALL x2
YES
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
e.THX Audio Setting
f.THX Speaker Setup
[
[
SB
[
]
SUB W.
[ THX : ALL SMALL
]
:Finish
:Return
These settings are designed to fine-tune your system, but
if you’re satisfied with the settings made in Automatically
setting up for surround sound (Auto MCACC) on page 8, it
isn’t necessary to make all of these settings.
2
Choose the set of speakers that you want to set
then select a speaker size.
Use ꢂ/ꢃ to select the size (and number) of each of the
following speakers:
Caution
• Front – Select LARGE if your front speakers
reproduce bass frequencies effectively, or if you
didn’t connect a subwoofer. Select SMALL to send
• The test tones used in the System Setup are output at
high volume.
1
the bass frequencies to the subwoofer.
1
Select ‘Manual SP Setup’ then press ENTER.
• Center – Select LARGE if your center speaker
reproduces bass frequencies effectively, or select
SMALL to send bass frequencies to the other
speakers or subwoofer. If you didn’t connect a center
speaker, choose NO (the center channel is sent to
the other speakers).
System Setup
1.Surr Back System
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
4.Manual SP Setup
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
e.THX Audio Setting
f.THX Speaker Setup
:
Exit
:Return
• Surr – Select LARGE if your surround speakers
reproduce bass frequencies effectively. Select
SMALL to send bass frequencies to the other
speakers or subwoofer. If you didn’t connect
surround speakers choose NO (the sound of the
surround channels is sent to the other speakers).
2
Select the setting you want to adjust.
If you are doing this for the first time, you may want to
adjust these settings in order:
• Speaker Setting – Specify the size and number of
speakers you’ve connected (page 40).
• SB – Select the number of surround back speakers
you have (one, two or none). Select LARGE if your
surround back speakers reproduce bass frequencies
effectively. Select SMALL to send bass frequencies to
the other speakers or subwoofer. If you didn’t
• Crossover Network– Specify which frequencies will
be sent to the subwoofer (page 41).
• Channel Level – Adjust the overall balance of your
speaker system (page 41).
2
• Speaker Distance – Specify the distance of your
connect surround back speakers choose NO.
speakers from the listening position (page 42).
• SUB W. – LFE signals and bass frequencies of
channels set to SMALL are output from the
subwoofer when YES is selected (see notes below).
Choose the PLUS setting if you want the subwoofer to
output bass sound continuously or you want deeper
bass (the bass frequencies that would normally come
out the front and center speakers are also routed to
the subwoofer). If you did not connect a subwoofer
choose NO (the bass frequencies are output from
other speakers).
• THX Audio Setting – Specify the distance of your
surround back speakers from each other (page 42).
• THX Speaker Setup – Specify whether or not you
have a THX speaker system (page 42).
3
Make the adjustments necessary for each
setting, pressing RETURN to confirm after each
screen.
Speaker Setting
3
When you’re finished, press RETURN.
Use this setting to specify your speaker configuration
(size, number of speakers). It is a good idea to make sure
that the settings made in Automatically setting up for
surround sound (Auto MCACC) on page 8 are correct.
You return to the Manual SP Setup menu.
Note
1 If you select SMALL for the front speakers the subwoofer will automatically be fixed to YES. Also, the center, surround, and surround back speakers can’t
be set to LARGE if the front speakers are set to SMALL. In this case, all bass frequencies are sent to the subwoofer.
2 • If the surround speakers are set to NO, the surround back speakers will automatically be set to NO.
• If you selected Speaker B or Front Bi-Amp (in Surround back speaker setting on page 35) you can’t adjust the surround back settings.
• If you select one surround back speaker only, make sure that speaker is hooked up to the left surround back terminal.
40
En
Download from Www.Somanuals.com. All Manuals Search And Download.
The System Setup menu
07
1
Select ‘Channel Level’ from the Manual SP Setup
Tip
menu.
• If you have a subwoofer and like lots of bass, it may
seem logical to select LARGE for your front speakers
and PLUS for the subwoofer. This may not, however,
yield the best bass results. Depending on the speaker
placement of your room you may actually experience
a decrease in the amount of bass due to low
4.Manual SP Setup
4c.Channel Level
Test Tone
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
e.THX Audio Setting
f.THX Speaker Setup
Manual
ENTER:Next
:Cancel
:Return
frequency cancellations. In this case, try changing
the position or direction of speakers. If you can’t get
good results, listen to the bass response with it set to
PLUS and YES or the front speakers set to LARGE and
SMALL alternatively and let your ears judge which
sounds best. If you’re having problems, the easiest
option is to route all the bass sounds to the
2
3
Select a setup option.
• Manual – Move the test tone manually from speaker
to speaker and adjust individual channel levels.
• Auto – Adjust channel levels as the test tone moves
from speaker to speaker automatically.
Confirm your selected setup option.
subwoofer by selecting SMALL for the front speakers.
The test tones will start after you press ENTER.
Crossover Network
4c.Channel Level
Test Tone
[
.
Manual
]
• Default setting: 80Hz
Please Wait
.
.
20
This setting decides the cutoff between bass sounds
playing back from the speakers selected as LARGE, or
the subwoofer, and bass sounds playing back from those
selected as SMALL. It also decides where the cutoff will
Caution!
Loud test tones
will be output.
:Cancel
1
be for bass sounds in the LFE channel.
4
Adjust the level of each channel using ꢂ/ꢃ.
If you selected Manual, use ꢀ/ꢁto switch speakers. The
Auto setup will output test tones in the order shown on-
screen:
1
Select ‘Crossover Network’ from the Manual SP
Setup menu.
4.Manual SP Setup
4b.Crossover Network
Frequency 80Hz
4c.Channel Level
a.Speaker Setting
b.Crossover Network
c.Channel Level
L
0.0dB
C
[
[
[
[
[
[
[
0.0dB ]
0.0dB ]
0.0dB ]
0.0dB ]
0.0dB ]
0.0dB ]
0.0dB ]
d.Speaker Distance
e.THX Audio Setting
f.THX Speaker Setup
R
SR
SBR
SBL
SL
SW
( THX
:
80Hz
)
:Return
:Finish
:Finish
2
Choose the frequency cutoff point.
Adjust the level of each speaker as the test tone is
emitted.
Frequencies below the cutoff point will be sent to the
subwoofer (or LARGE speakers).
2
5
When you’re finished, press RETURN.
3
When you’re finished, press RETURN.
You return to the Manual SP Setup menu.
You return to the Manual SP Setup menu.
Channel Level
Tip
Using the channel level settings, you can adjust the
overall balance of your speaker system, an important
factor when setting up a home theater system.
• You can change the channel levels at any time by
using EFFECT/CH SEL and +/– on the remote control.
You can set two channel levels: one for MULTI CH IN
and one for the listening modes.
Note
1 • For more on selecting the speaker sizes, see Speaker Setting above.
• If you’re using a THX speaker setup, confirm that the crossover frequency is set to 80Hz.
2 • If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and adjust the level of each speaker to 75 dB
SPL (C-weighting/slow reading).
• The subwoofer test tone is output at low volumes. You may need to adjust the level after testing with an actual soundtrack.
41
En
Download from Www.Somanuals.com. All Manuals Search And Download.
The System Setup menu
07
• 0–1 ft – Surround speakers within 1 foot apart (best
for THX surround sound).
Speaker Distance
For good sound depth and separation from your system,
you need to specify the distance of your speakers from
the listening position. The receiver can then add the
proper delay needed for effective surround sound.
• 1– 4 ft – Surround speakers between 1 and 4 feet
apart.
• 4 ft < – Surround speakers more than 4 feet apart.
1
Select ‘Speaker Distance’ from the Manual SP
3
When you're finished, press RETURN.
Setup menu.
You will return to the Manual SP Setup menu.
4d.Speaker Distance
4.Manual SP Setup
THX Speaker Setup
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
e.THX Audio Setting
f.THX Speaker Setup
L
10.0ft
9.5ft
9.0ft
6.5ft
6.5ft
6.0ft
6.0ft
C
R
[
[
[
[
[
[
]
]
]
]
]
If you have a complete THX speaker system, you should
make this setting for the most effective results when
using surround sound. See THX speaker system setup on
page 20 for more on using a THX speaker system.
SR
SBR
SBL
SL
SW
12.5ft ]
:Finish
:Return
1
Select ‘THX Speaker Setup’ from the Manual SP
2
Adjust the distance of each speaker using ꢂ/ꢃ.
Setup menu.
You can adjust the distance of each speaker in 0.5 foot
increments.
4.Manual SP Setup
a.Speaker Setting
b.Crossover Network
c.Channel Level
3
When you’re finished, press RETURN.
d.Speaker Distance
e.THX Audio Setting
f.THX Speaker Setup
You return to the Manual SP Setup menu.
:Return
Tip
• For best surround sound, make sure the surround
back speakers are the same distance from the
listening position.
2
Specify whether or not you are using a THX speaker
system.
4f.THX Speaker Setup
THX Speaker
NO
THX Audio Setting
If you are using THX
speakers, select YES.
For the most effective results when using the THX Select2
Cinema and THX MusicMode listening modes (see Using
the Home THX modes on page 28) with the Advanced
Speaker Array (ASA) system (see About THX on page 69),
it is required that you make the setting. See THX speaker
system setup on page 20 for more on THX speaker
:Finish
• YES – All speaker settings are fixed to SMALL (see
Speaker Setting on page 40) during the Auto MCACC
setup.
1
placement.
• NO – Individual speaker sizes are determined
according to the Auto MCACC setup.
1
Select ‘THX Audio Setting’ from the Manual SP
Setup menu.
3
When you're finished, press RETURN.
4.Manual SP Setup
You will return to the Manual SP Setup menu.
a.Speaker Setting
b.Crossover Network
c.Channel Level
d.Speaker Distance
e.THX Audio Setting
f.THX Speaker Setup
:Return
2
Specify the distance of your surround back speakers
from each other.
4e.THX Audio Setting
SB SP Position
0-1 ft
SBL-SBR
:Finish
Note
1 If you don’t have surround back speakers, or just have one, you won’t be able to select this setting (Cannot select shows in the display).
42
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connections
08
Chapter 8:
Other connections
1
Set this receiver to the standby mode, and then use
Caution
the Control Dock for iPod supplied with an iPod control
2
• Make sure the power is switched off before making or
changing the connections.
cable to connect your iPod to the iPod terminal on the
rear panel of this receiver.
Push the connector in until you hear it click home. To
disconnect, squeeze the connector (as shown) to release
the catch, then pull out.
Connecting an iPod
This receiver has a dedicated iPod terminal that will allow
you to control playback of audio content from your iPod
2
Switch the receiver on and press the iPod input
source button to switch the receiver to the iPod.
The front panel display shows Loading while the receiver
verifies the connection and retrieves data from the iPod.
1
using the controls of this receiver.
Connecting your iPod to the receiver
3
Use the TOP MENU button to display iPod Top
menu.
When the display shows Top Menu you’re ready to play
3
music from the iPod.
• If after pressing iPod the display shows No
Connection, try switching off the receiver and
reconnecting the iPod to the receiver.
AM LOOP
PRE OUT
L
CENTER
L
P
R
OUT
I
2
(
)
TV/SAT
IN
3
(
)
TV/SAT
P
B
iPod playback
IN
CD
3
)
R
SUB
R
SUR-
ROUND
(
FRONT WOOFER
ASSIGNABLE
OUT
To navigate songs on your iPod, you can take advantage
of the OSD of your TV connected to this receiver. You can
also control all operations for music in the front panel
display of this receiver.
1
3
-I
SIR
HDMI
ASSIG-
NABLE
4
IN
IN
OUT
OUT
IN
IN
OUT
OUT
IN
IN
MONITOR
OUT
CONTROL
OUT
iPod
IN
1
2
VIDEO
XM
IN
IN
CENTER
AUDIO
L
IN
OUT
IN
IN
L
IN
(
1
)
DVD/LD
Finding what you want to play
R
IN
2
(
)
DVR/VCR2
R
CD
CD-R/TAPE/MD DVD/LD TV/SAT
DVR/VCR1
DVR/VCR2
SUB
WOOFE
FRONT
COAXIAL
When your iPod is connected to this receiver, you can
browse songs stored on your iPod by playlist, artist,
album name, song name, genre or composer, similar to
using your iPod directly.
ASSIGNABLE
MULTI CH IN
1
2
VSX-1017TXV
iPod
>
Shuffle Songs
Backlight
Music
Extras
>
>
Settings
iPod cable
iPod Top
[ Playlists
[ Artists
]
]
]
]
]
]
]
]
]
MENU
[
Albums
ꢅ
ꢄ
[ Songs
[ Podcasts
[
Genres
[ Composers
[ Audiobooks
[ Shuffle Songs
Enter
Control Dock
for iPod
1
Use the ꢀ/ꢁ buttons to select a category then
press ENTER to browse that category.
• To return to the previous level any time, press
RETURN.
Note
This system is compatible with an iPod, iPod mini, iPod nano and iPod Photo portable device (third generation and above), however, compatibility may
1
vary depending on the software version of your iPod. This receiver does not support software versions prior to iPod update 2004-10-20. For supported
versions, consult your local Pioneer dealer.
2 • This product is the Pioneer Control Dock for iPod (IDK-90C) for use with an iPod® (third generation and above), iPod mini, iPod nano or iPod Photo.
• For detailed instructions on using the iPod, please refer to the manual supplied with the iPod.
• The connected iPod should be updated with iPod updater software higher than version 2004-10-20.
3 The controls of your iPod will be inoperable when connected to this receiver (Pioneer shows in the iPod display). Features such as the equalizer cannot
be controlled using this receiver, and we recommend switching the equalizer off before connecting.
4 • Note that non-roman characters in the playlist are displayed as #.
• This feature is not available for photos or video clips on your iPod.
43
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connections
08
2
Use the ꢀ/ꢁ buttons to browse the selected
Button
What it does
category (e.g., albums).
TOP
MENU
Press to return to the iPod Top menu screen.
• Use ꢂ/ꢃ to move to previous/next levels.
3
Continue browsing until you arrive at what you
RETURN
Press to return to the previous level.
1
want to play, then press
ꢁ
to start playback.
Navigation through categories on your iPod looks like
this:
Playlists ꢄ Songs
Artists ꢄ Albums ꢄ Songs
Albums ꢄ Songs
Watching photos and video content
To view photos or video on your iPod, since video control
is not possible using this receiver, you must use the main
2
controls of your iPod instead.
Songs
Podcasts
1
Press PHOTO to switch the iPod controls for photo
and video playback.
The receiver controls will be unavailable while you are
watching iPod videos or browsing photos.
Genres ꢄ Artists ꢄ Albums ꢄ Songs
Composers ꢄ Albums ꢄ Songs
Audiobooks
Shuffle Songs
2
Press PHOTO again to switch back to the receiver
controls when you’re done.
Tip
iPod® is a trademark of Apple Inc., registered in the U.S.
and other countries.
• You can play all of the songs in a particular category
by selecting the All item at the top of each category
list. For example, you can play all the songs by a
particular artist.
Using XM Radio
Basic playback controls
The following table shows the basic playback controls for
your iPod:
XM Satellite Radio offers an extraordinary variety of
commercial-free music, plus the best in sports, news,
talk and entertainment. XM is broadcast in superior
digital audio from coast to coast. From rock to reggae,
from classical to hip hop, XM has something for every
music fan. XM’s dedication to playing the richest
selection of music is matched by its passion for live
sporting events, talk radio, up-to-the-minute news, stand-
up comedy, children’s programming, and much more.
For U.S. customers, information about XM Satellite Radio
customers, information about XM Canada is online at
Button
What it does
ꢁ
Press to start playback.
If you start playback when something other than a
song is selected, all the songs that fall into that
category will play.
ꢂ
ꢆ
Press to stop playback.
Pauses playback, or restarts playback when
paused.
ꢇ/ꢈ Press and hold during playback to start scanning.
ꢅ/ꢄ Press to skip to previous/next track.
Connecting your XM Radio receiver
After purchasing an XM Mini-Tuner (sold separately), you
will also need to activate the XM Radio digital radio
service to receive broadcasts.
Press repeatedly to switch between Repeat One,
Repeat All and Repeat Off.
3
Press repeatedly to switch between Shuffle Songs,
Shuffle Albums and Shuffle Off.
DISP
Press repeatedly to change the song playback
information displayed.
ꢂ/ꢃ
During playback, press to skip to previous/next
playlist; when browsing, press to move to previous/
next levels.
During Audiobook playback, press to switch the
playback speed: Faster ꢅ Normal ꢅ Slower
ꢀ/ꢁ
Note
1 If you’re in the song category, you can also press ENTER to start playback.
2 Your iPod nano currently restricts viewing of photo images stored.
3 Hardware and required basic monthly subscription sold separately. Premium Channel available at additional monthly cost. Installation costs and other
fees and taxes, including a one-time activation fee may apply. Subscription fee is consumer only. All fees and programming subject to change. Channels
with frequent explicit language are indicated with an XL. Channel blocking is available for XM radio receivers by calling 1-800-XMRADIO. Subscriptions
subject to Customer Agreement available at xmradio.com. Only available in the 48 contiguous United States.
44
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connections
08
Selecting channels and browsing by genre
From the XM Channel Guide, you can browse XM Radio
channels in the order that they appear, or you can narrow
your channel search by genre.
ANTENNA
OPTICAL
DIGITAL
OUT
IN
1
AM LOOP
L
PRE OUT
L
COMPONENT VIDEO
DVD/LD
L (Single)
CENTER
(
)
IN
1
Y
IN
PB
PR
Y
Y
PB
PR
(
DVR/
)
VCR1
1
IN
2
IN
2
(
)
TV/SAT
IN
2
Y
IN
3
(
)
TV/SAT
R
PB
PR
PB
3
PR
IN
3
)
R
SUB
FRONT WOOFER
R
SUR-
ROUND
SURROUND BACK
1
(
CD
ASSIGNABLE
OUT
1
3
S-VIDEO
SIRIUS
HDMI
ASSIG-
NABLE
IN
XM Satellite Radio
A
XM Channel Guide
Previous
IN
VIDEO
IN
IN
OUT
OUT
IN
OUT
OUT
IN
IN
MONITOR
OUT
CONTROL
OUT
iPod
IN
1
2
XM
IN
[
[
[
[
[
[
[
[
]
]
]
]
]
]
]
]
000 RADIO ID ID
001 Preview
IN
Decades
The 50s
A0
XM005
CENTER
L
OUT
IN
IN
IN
L
L
L
002 Highway1
003 America
IN
1
(
)
DVD/LD
004 Hank’s Place
005 Fifties (50’s)
006 Sixties (60’s)
007 Seventies (70’s)
Remy Sherman
Lovin' You
R
IN
2
(
)
DVR/VCR2
R
R
R
CD
CD-R/TAPE/MD DVD/LD TV/SAT
DVR/VCR1
DVR/VCR2
SUB
WOOFER
FRONT
SUR-
SURROUND
COAXIAL
ROUND BACK
ASSIGNABLE
1
MULTI CH IN
2
ENTER
Next
:
Exit
VSX-1017TXV
•
Press ꢀ/ꢁ to display the XM Channel Guide then
ꢀ/ꢁ and ENTER to select the channel of the XM radio
broadcast you want to hear.
SATELLiTE
RADiO
• To browse by genre, first press SETUP, use ꢀ/ꢁ to
select a genre then press ENTER.
3
SATELLiTE RADiO
• To cancel and exit any time, press RETURN.
XM Mini-Tuner
Connect an XM Mini-Tuner to the XM Radio jack on
Tip
1
the rear of this receiver.
You will also need to activate the XM Radio service.
• You can select channels directly by pressing
D.ACCESS then the three-digit channel number.
2
Press XM RADIO (SHIFT+DVD) to switch to the XM
• You can press DISP to change XM Radio information
in the front panel display.
RADIO input.
For best reception, you may need to move the XM Mini-
Tuner near a window (the southernmost window should
produce the best results).
• The currently selected channel is automatically
chosen (without pressing ENTER) after 5 seconds.
• If after pressing XM RADIO the display shows Check
Tuner, try disconnecting the receiver and tuner
connections and then plugging them back in. If the
display shows Check Antenna, try disconnecting the
tuner and antenna connections and then plugging
Using XM HD Surround
XM HD Surround uses Neural Surround™ technology to
achieve optimal surround sound from XM radio.
•
While listening to XM Radio, press AUTO SURR
1
for XM HD Surround listening.
See About Neural Surround™ below for more on this.
them back in.
Listening to XM Radio
About Neural Surround™
After connecting, you will be able to use this receiver to
select channels and navigate categories using the on-
Neural Surround™ represents the latest advancement in
surround technology and has been adopted by XM
Satellite Radio for digital radio broadcasts of surround
recordings and live events.
2
screen display. The information displayed is as follows:
Preset class
Signal strength
Category
XM Satellite Radio
A
Neural Surround™ employs psychoacoustic frequency
domain processing which allows delivery of a more
detailed sound stage with superior localization of
surround elements. System playback is scalable from
stereo up to state-of-the-art multichannel surround.
Decades
The 50s
A0
XM005
Preset number
Channel number
Artist name
Remy Sherman
Lovin' You
Song name
Channel name
Neural Surround™ is trademark owned by Neural Audio
Corporation.
Saving channel presets
This receiver can memorize up to 30 channels, stored in
three banks, or classes (A, B and C) of 10 stations each.
Note
1 You can check the strength of reception in Using the XM Menu (page 46).
2 It’s easiest if you have your TV switched on to take advantage of the OSDs. You can, however, use just the front panel display to do everything if you prefer.
3 Select XM000 (RADIO ID) from the on-screen display to check the Radio ID of the XM Mini-Tuner.
45
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connections
08
1
Select the channel you want to memorize.
See Selecting channels and browsing by genre above.
Press T.EDIT
The display shows a blinking memory class.
Press CLASS to select one of the three classes then
press ꢂ/ꢃ to select the channel preset you want.
You can also use the number buttons to select a preset.
Using SIRIUS Radio
TM
2
.
With SIRIUS you get The Best Radio on Radio with all
your favorite entertainment including 100 % commercial-
free music, plus superior sports coverage, uncensored
talk and comedy, world-class entertainment, news,
weather and more for your car, home or office. For more
information visit sirius.com or siriuscanada.ca
3
• The default for all presets is XM001.
Sirius is available in the US for subscribers with
addresses in the continental US and is available in
Canada for subscribers with a Canadian address.
Required subscription plus compatible SIRIUS tuner and
antenna are required and sold separately. SIRIUS
Programming is subject to change. Visit HYPERLINK
complete and up-to-date channel lineup and product
information. “SIRIUS” and the SIRIUS dog logo and
related marks are trademarks of Sirius Satellite Radio
Inc. All rights reserved.
4
Press ENTER.
After pressing ENTER, the preset class and number stop
blinking and the receiver stores the XM channel.
Tip
• You can also press ꢄ during reception display to
save the information of up to 8 songs. See Using the
XM Menu below to recall this information.
Listening to channel presets
You will need to have some presets stored to do this.
Connecting your SIRIUS Connect Tuner
To receive SIRIUS Satellite Radio broadcasts, you will
1
Press CLASS to select the class in which the channel
1
is stored.
need to activate your SIRIUS Connect tuner.
Press repeatedly to cycle through classes A, B and C.
VSX-1017TXV
2
Press ꢂ/ꢃ to select the channel preset you want.
• You can also use the number buttons on the remote
control to recall the channel preset.
OPTICAL
DIGITAL
OUT
IN
AM LOOP
PRE OUT
L
1
COMPONENT VIDEO
Y
IN
1
L
L (Single)
CENTER
(DVD/LD)
IN
DVR/
VCR1
1
PB
PR
Y
Y
PB
PR
(
)
IN
TV/SAT
2
IN
2
(
)
IN
2
IN
3
Using the XM Menu
The XM Menu provides additional XM Radio features.
(TV/SAT)
R
Y
PB
PR
PB
3
PR
IN
CD
3
)
R
SUB
R
SUR-
ROUND
SURROUND BACK
1
(
FRONT WOOFER
ASSIGNABLE
OUT
1
3
S-VIDEO
IN
SIRIUS
HDMI
ASSIG-
NABLE
IN
VIDEO
IN
IN
OUT
OUT
IN
OUT
OUT
IN
IN
MONITOR
OUT
CONTROL
OUT
iPod
IN
1
2
1
Press TOP MENU.
XM
IN
IN
CENTER
AUDIO
L
IN
OUT
IN
IN
IN
L
L
L
2
Use ꢀ/ꢁ to select a menu item then press ENTER
.
IN
1
(
)
DVD/LD
Choose between the follwing menu items:
R
IN
2
(
)
DVR/VCR2
R
R
R
CD
CD-R/TAPE/MD DVD/LD TV/SAT
DVR/VCR1
DVR/VCR2
SUB
WOOFER
FRONT
SUR-
SURROUND
COAXIAL
ROUND BACK
• Memory Recall – Use ꢀ/ꢁ to browse your saved
song information (See Tip above)
• Channel Skip/Add – Use ꢀ/ꢁ and ENTER to select
channels you would like to remove/restore from/to
the channel guide.
ASSIGNABLE
MULTI CH IN
1
2
Antenna
• Antenna Aiming – Check the strength of satellite
and terrestrial reception.
SIRIUS
★
3
When you’re finished press TOP MENU to return to
the reception display.
®
AC adapter
SiriusConnect™ HOME tuner
Connect & Play™, XM-Ready and The Ultimate Playlist are
trademarks of XM Satellite Radio Inc. ©2005 XM Satellite
Radio Inc. All rights reserved. All other trademarks are the
property of their respective owners.
1
Connect a SIRIUS Connect tuner to the SIRIUS Radio
jack on the rear of this receiver.
You will also need to connect the antenna and AC
adapter to the Sirius Connect tuner.
Note
1 • In order to activate your radio subscription, you will need the SIRIUS ID (SID) which uniquely identifies your tuner. The SID may be found on a sticker
located on the packaging, or on the bottom of the tuner itself. The label will have a printed 12-digit SID number. When you have located the SID, write it
Follow the prompts to activate your subscription, or you can also call SIRIUS toll-free at 1-888-539-SIRIUS (1-888-539-7474).
• Select SR000 (SIRIUS ID) from the on-screen display to check the Radio ID of the SIRIUS Connect tuner ( see Selecting channels and browsing by genre
on page 47).
46
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connections
08
2
Press SIRIUS (SHIFT+TV) to switch to the SIRIUS
• The currently selected channel is automatically
input.
chosen (without pressing ENTER) after 10 seconds.
For best reception, you may need to move the SIRIUS
Connect tuner antenna near a window (Refer to the
manual for the SiriusConnect Home tuner for antenna
placement recommendations).
Saving channel presets
This receiver can memorize up to 30 channels, stored in
3
three banks, or classes (A, B and C) of 10 stations each.
Select the channel you want to memorize.
See Selecting channels and browsing by genre above.
Press T.EDIT
The display shows a blinking memory class.
Press CLASS to select one of the three classes then
• If after pressing SIRIUS the display shows Antenna
1
Error, try disconnecting the antenna and
1
reconnecting. If the display shows Check Sirius
2
.
Tuner, check the connection of the AC adapter and
this receiver to the Sirius Connect tuner.
3
press ꢂ/ꢃ to select the channel preset you want.
Listening to SIRIUS Radio
You can also use the number buttons to select a preset.
After connecting, you will be able to use this receiver to
select channels and navigate categories using the on-
4
Press ENTER.
After pressing ENTER, the preset class and number stop
blinking and the receiver stores the SIRIUS channel.
2
screen display. The information displayed is as follows:
4
Preset class
Signal strength
Category
SIRIUS
A
Tip
Decades
The '50s
A0
Preset number
• You can also press ꢄ during reception display to
SR005
Chuck Berry
Channel number
Artist name
save the information of up to 8 songs. See Using the
4
SIRIUS Menu below to recall this information.
Johnny B. Good
Song name
Channel name
Listening to channel presets
You will need to have some presets stored to do this.
Selecting channels and browsing by genre
From the SIRIUS Channel Guide, you can browse SIRIUS
Radio channels in the order that they appear, or you can
narrow your channel search by genre.
1
Press CLASS to select the class in which the channel
is stored.
Press repeatedly to cycle through classes A, B and C.
2
Press ꢂ/ꢃ to select the channel preset you want.
• You can also use the number buttons on the remote
control to recall the channel preset.
SIRIUS
A
SIRIUS Channel Guide
Next
[
[
[
[
[
[
[
[
]
]
]
]
]
]
]
]
007 The '70s
006 The '60s
005 The '50s
004 Easy Listening
003 Love Songs
002 Lite Pop
Decades
The '50s
A0
SR005
Chuck Berry
Using the SIRIUS Menu
The SIRIUS Menu provides additional SIRIUS Radio
features.
001 Top 40 Hits
000 Sirius ID
Johnny B. Good
ENTER
Previous
:
Exit
4
1
Press TOP MENU.
•
Press ꢀ/ꢁ to enter the SIRIUS Channel Guide, then
navigate through the channels one at time with the
ꢀ/ꢁ buttons or switch through pages with the ꢂ/ꢃ
buttons, then press ENTER to listen to the SIRIUS radio
broadcast.
• To browse by genre, first press SETUP, use
ꢀ/ꢁ/ꢂ/ꢃ to select a genre then press ENTER.
2
Use ꢀ/ꢁ to select a menu item then press ENTER
.
Choose between the following menu items:
• Memory Recall – Use ꢀ/ꢁ to browse your saved
song information (see Tip above).
• Channel Skip/Add – Use ꢀ/ꢁ and ENTER to select
channels you would like to remove/restore from/to
the channel guide.
• To cancel and exit any time, press RETURN.
• Parental Lock – Use ꢀ/ꢁ and ENTER to select
channels you would like to place under parental lock.
Channels put under parental lock are not displayed in
the Channel Guide, but may be accessed by directly
inputting their channel number and providing the
parenal lock password.
Tip
• You can select channels directly by pressing
D.ACCESS then the three-digit channel number.
• You can press DISP to change SIRIUS Radio
information in the front panel display.
Note
1 You can check the strength of reception in Using the SIRIUS Menu on page 47.
2 It’s easiest if you have your TV switched on to take advantage of the OSDs. You can, however, use just the front panel display to do everything if you prefer.
3 Note that channels locked out with parental lock cannot be saved on this receiver.
4 You can reset the Channel presets, Memory, Channel Skip/Add, Parental Lock and Password settings in Resetting the system on page 56.
47
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connections
08
• Antenna Aiming – Check the strength of satellite
and terrestrial reception.
• Password Set – Set the parental lock password.
Speaker B setup
3
When you’re finished press TOP MENU to return to
Caution
the reception display.
• Before making or changing the connections, switch off
the power and disconnect the power cord from the
power outlet. Plugging in components should be the
last connection you make with your system.
Connecting the multichannel analog
inputs
• Be careful not to allow any contact between speaker
wires from different terminals.
For DVD Audio and SACD playback, your DVD player may
have 5.1, 6.1 or 7.1 channel analog outputs (depending
on whether your player supports surround back
• You can use speakers with a nominal impedance
between 6 Ω to 16 Ω (please see Switching the
speaker impedance on page 56 if you plan to use
speakers with an impedance of less than 8 Ω).
1
channels). Make sure that the player is set to output
multichannel analog audio.
1
Connect the front, surround, center and subwoofer
After selecting Speaker B in Surround back speaker
setting on page 35, you can use the speakers connected
to the (surround back) B speaker terminals on the rear
panel to listen to stereo playback in another room. See
Switching the speaker system below for the listening
options with this setup.
outputs on your DVD player to the corresponding
MULTI CH input jack on this receiver.
• Use standard RCA/phono jack cables for the
connections.
2
If your DVD player also has outputs for surround
back channels, connect these to the corresponding
MULTI CH input jacks on this receiver.
• Use standard RCA/phono jack cables for the
connections.
1
Connect a pair of speakers to the surround back
speaker terminals on the rear panel.
Connect them the same way you connected your
speakers in Installing your speaker system on page 18.
Make sure to review Placing the speakers on page 19
when placing the speakers in another room.
• If there is a single surround back output, connect it to
the SURROUND BACK L (Single) jack on this
receiver.
2
Select ‘Speaker B’ from the ‘Surr Back System’
menu.
Selecting the multichannel analog inputs
If you have connected a decoder or a DVD player as
above, you must select the analog multichannel inputs
See Surround back speaker setting on page 35 to do this.
Switching the speaker system
2
for surround sound playback.
If you selected Speaker B in Surround back speaker
setting on page 35, three speaker system settings are
possible using the SPEAKERS button. If you selected
Normal (SB) or Front Bi-Amp, the button will simply
switch your main speaker system on or off. The options
1
Make sure you have set the playback source to the
proper output setting.
For example, you might need to set your DVD player to
output multichannel analog audio.
3
below are for the Speaker B setting only.
2
Press MULTI CH IN (front panel).
•
Use the SPEAKERS button on the front panel to
• Depending on the DVD player you’re using, the
analog output level of the subwoofer channel may be
too low. In this case switch the receiver into standby,
then press ꢀ STANDBY/ON while holding down
SBch PROCESSING on the front panel. This switches
between SW IN +10dB (increase of 10 decibels) and
SW IN 0dB (default) in the subwoofer channel.
select a speaker system setting.
As mentioned above, if you have selected Normal (SB),
the button will simply switch your main speaker system
(A) on or off.
Press repeatedly to choose a speaker system option:
• SPꢁA – Sound is output from speaker system A and
the same signal is output from the pre-out terminals.
Note
1 To listen to multichannel analog audio you’ll need to select MULTI CH IN (see Selecting the multichannel analog inputs above for more on this).
2 • When playback from the multichannel inputs is selected, you can’t use the sound processing features, SIGNAL SELECT, or any of the listening modes
(including STEREO and the surround back channel processing).
• When playback from the multichannel inputs is selected, only the volume and channel levels can be set.
• You can’t listen to your speaker B system during playback from the multichannel inputs.
3 • The subwoofer output depends on the settings you made in Manual speaker setup on page 40. However, if SPꢁB is selected above, no sound is heard
from the subwoofer (the LFE channel is not downmixed).
• Depending on the settings in Surround back speaker setting on page 35 output from the surround back pre-out terminals may change.
• All speaker systems (except Speaker B connections) are switched off when headphones are connected.
48
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connections
08
• SPꢁB – Sound is output from the two speakers
connected to speaker system B. Multichannel
sources will not be heard. The same signal is output
from the surround back channel pre-out terminals.
Caution
• Most speakers with both High and Low terminals
have two metal plates that connect the High to the
Low terminals. These must be removed when you are
bi-amping the speakers or you could severely
damage the amplifier. See your speaker manual for
more information.
• SPꢁAB – Sound is output from speaker system A (up
to 5 channels, depending on the source), the two
speakers in speaker system B, and the subwoofer.
The sound from speaker system B will be the same as
the sound from speaker system A (multichannel
sources will be downmixed to 2 channels).
• If your speakers have a removable crossover network,
make sure you do not remove it for bi-amping. Doing
so may damage your speakers.
• SPꢁ(off) – No sound is output from the speakers. The
same sound is output from the pre-out terminals
(including from your subwoofer, if connected) as
when selecting speaker system A (above).
Bi-wiring your speakers
The reasons for bi-wiring are basically the same as bi-
amping, but additionally, interference effects within the
wire could be reduced, producing better sound. Again, to
do this your speakers must be bi-wireable (that is they
must have separate terminals for the high and low
frequencies). When bi-wiring, make sure you’ve selected
Normal (SB) or Speaker B in Surround back speaker
setting on page 35.
Bi-amping your front speakers
Bi-amping is when you connect the high frequency driver
and low frequency driver of your speakers to different
amplifiers (in this case, to both front and surround back
terminals) for better crossover performance. Your
speakers must be bi-ampable to do this (having separate
terminals for high and low) and the sound improvement
will depend on the kind of speakers you’re using.
•
To bi-wire a speaker, connect two speaker cords to
the speaker terminal on the receiver.
Using a banana plug for the second connection is
recommended.
1
Connect your speakers as shown below.
This illustration below shows the connections for bi-
amping your front left speaker. Hook up your front right
speaker in the same way.
SPEAKERS
FRONT
CENTER
SURROUND
SURROUND BACK
/
A
B
R
L
R
L
R
L
( )
Single
Front left
speaker
SEE INSTRUCTION MANUAL
SELECTABLE
Caution
High
• Make sure you use a parallel (not series, which are
fairly uncommon) connection when bi-wiring your
speakers.
Low
• Don’t connect different speakers from the same
terminal in this way.
Since both front and surround back speaker terminals
output the same audio, it doesn’t matter which set (front
or surround back) is powering which part (High or Low)
of the speaker.
• Make sure that the + / – connections are properly
inserted.
2
Select the ‘Front Bi-Amp’ setting from the ‘Surr Back
System’ menu.
See Surround back speaker setting on page 35 to specify
how you’re using the surround back speaker terminals.
49
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connections
08
Connecting additional amplifiers
Using this receiver with a Pioneer
This receiver has more than enough power for any home
use, but it’s possible to add additional amplifiers to every
channel of your system using the pre-outs. Make the
connections shown below to add amplifiers to power
your speakers.
plasma display
If you have a Pioneer plasma display, you can use an
1
SR+ cable to connect it to this unit and take advantage
of various convenient features, such as automatic video
input switching of the plasma display when the input is
• Before making or changing the connections, switch
off the power and disconnect the power cord from the
AC outlet.
2
changed.
CONTROL
OUT
ANALOG
INPUT
L
R
Front channel
amplifier
AM LOOP
L
PRE OUT
L
L
CENTER
)
Single
ANALOG
OUT
INPUT
Pioneer plasma
IN
3
Center channel
amplifier (mono)
display
R
R
SUB
R
SUR-
ROUND
SURROUND BACK
FRONT WOOFER
VSX-1017TXV
ANALOG
INPUT
ANTENNA
OPTICAL
DIGITAL
SIRIUS
L
R
OUT
IN
1
IN
OUT
OUT
IN
IN
MONITOR
OUT
Surround channel
amplifier
AM LOOP
COMPONENT VIDEO
C
(
)
DVD/LD
L
IN
1
Y
P
B
P
R
Y
P
B
P
R
(
DVR/
VCR1
IN
1
OUT
)
IN
2
IN
2
(
)
ANALOG
INPUT
TV/SAT
IN
2
Y
IN
3
(
)
TV/SAT
P
B
P
R
Y
P
B
3
P
R
IN
(
3
)
R
S
W
CENTER
L
R
L
L
L
ASSIGNABLE
1
CD
FRONT
ASSIGNABLE
OUT
1
3
Surround back
channel amplifier
S-VIDEO
HDMI
ASSIG-
NABLE
IN
IN
IN
OUT
IN
IN
OUT
OUT
IN
CONTROL
OUT
iPod
IN
1
2
VIDEO
ANALOG
XM
IN
INPUT
IN
R
R
R
DVR/VCR2
SUB
WOOFER
FRONT
SUR-
SURROUND
Powered
subwoofer
ROUND BACK
AUDIO
L
IN
OUT
IN
IN
OUT
IN
MULTI CH IN
IN
(
1
)
DVD/LD
R
VSX-1017TXV
IN
2
(
)
DVR/VCR2
CD
CD-R/TAPE/MD DVD/LD TV/SAT
DVR/VCR1
DVR/VCR2
COAXIAL
ASSIGNABLE
1
2
• You can use the additional amplifier on the surround
back channel pre-outs for a single speaker as well. In
this case plug the amplifier into the left (L (Single))
terminal only.
Important
• If you connect to a Pioneer plasma display using an
SR+ cable, you will need to point the remote control
at the plasma display remote sensor to control the
receiver. In this case, you won’t be able to control the
receiver using the remote control if you switch the
plasma display off.
• The sound from the surround back terminals will
depend on how you have configured the Surround
back speaker setting on page 35.
• To hear sound only from the pre-outs, switch the
speaker system to OFF, or simply disconnect any
speakers that are connected directly to the receiver.
• Before you can use the extra SR+ features, you need
to make a few settings in the receiver. See The Input
Assign menu on page 52 and SR+ Setup for Pioneer
plasma displays on page 54 for detailed instructions.
• If you’re not using a subwoofer, change the front
speaker setting (see Speaker Setting on page 40) to
LARGE.
Note
1 The 3-ringed SR+ cable from Pioneer is commercially available under the part number ADE7095. Contact the Pioneer Customer Support division for
more information on obtaining an SR+ cable (you can also use a commercially available 3-ringed mini phone plug for the connection).
2 This receiver is compatible with all SR+ equipped Pioneer plasma displays from 2003 onward.
50
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connections
08
•
Use a 3-ringed miniplug SR+ cable to connect the
CONTROL IN jack of this receiver with the CONTROL
OUT jack of your plasma display.
Using the SR+ mode with a Pioneer
plasma display
When connected using an SR+ cable, a number of
features become available to make using this receiver
with your Pioneer plasma display even easier. These
features include:
• On-screen displays when making receiver settings,
such as speaker setup, MCACC setup, and so on.
VIDEO
INPUT 1
VIDEO
INPUT 2
Pioneer plasma
display
• On-screen volume display.
• On-screen display of listening mode.
• Automatic video input switching on the plasma
display.
• Automatic volume muting on the plasma display.
DVD player
Satellite receiver, etc.
See also SR+ Setup for Pioneer plasma displays on
page 54 for more on setting up the receiver.
DVD/LD
AUDIO IN
TV/SAT
AUDIO IN
Important
-1017TXV
AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX
PHASE
STANDBY/ON
• The additional SR+ features do not work when the
iPod, XM or SIRIUS Radio function is selected.
CONTROL
DIGITAL PRECISION PROCESSING
PHASE
CONTROL
ACOUSTIC LISTENING
EQ
MODE
SIGNAL
SB ch
MULTI CH
IN
DVD/LD
TV
/
SAT
DVR/VCR
1
DVR/VCR
2
VIDEO/GAME
CD
CD-R
/
TAPE
/
MD
FM/AM
XM
SIRIUS
iPod
SELECT PROCESSING
ENTER
MASTER
VOLUME
MULTI JOG
XM RADIO
DVD
SIRIUS
TV
DVR
2
S
-
VIDEO
VIDEO/GAME INPUT
AUDIO
MCACC
SETUP MIC
VIDEO
L
R
DIGITAL IN
DVR 1
TV CTRL
PHONES
SYSTEM
SETUP
TUNING/
STATION
TUNER
EDIT
RETURN
TONE
SPEAKERS
CD-R/TAPE
CD
MULTI JOG
iPod
TUNER
SB ch
RECEIVER
SLEEP
ANALOG
ATT
This receiver
SR+
DIMMER
PHASE
MIDNIGHT/
LOUDNESS
To make the most of the SR+ features, you should
connect your source components (DVD player, etc.) in a
slightly different way to that described in this chapter. For
each component, connect the video output directly to the
plasma display, and just connect the audio (analog and/
or digital) to this receiver.
DIALOG
E
S.RETRIEVER
1
Make sure that the plasma display and this receiver
are switched on and that they are connected with the
SR+ cable.
See Using this receiver with a Pioneer plasma display
above for more on connecting these components.
• Make sure you have also selected the display input to
which you’ve connected the receiver in The Input
Assign menu on page 52.
2
To switch SR+ mode on/off, press RECEIVER, then
the SR+ button.
The front panel display shows SR+ ON or SR+ OFF.
• The automatic volume muting feature is enabled
separately; see SR+ Setup for Pioneer plasma displays
on page 54.
51
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Settings
09
Chapter 9:
Other Settings
• Use ꢂ/ꢃ and ENTER to do this.
• If you assign a digital input to a certain function (for
example, DVD/LD) then any digital inputs previously
assigned to that function will automatically be
switched off.
When you're finished, press RETURN.
You return to the Input Assign menu.
The Input Assign menu
You only need to make settings in the Input Assign menu
if you didn’t hook up your digital equipment according to
the default settings for the digital inputs, or if you have
connected equipment using component video cables.
4
1
Press RECEIVER on the remote control, then press
the SETUP button.
Assigning the component video inputs
An on-screen display (OSD) appears on your TV. Use ꢀ/
ꢁ/ꢂ/ꢃ and ENTER to navigate through the screens
and select menu items. Press RETURN to confirm and
exit the current menu.
• Default settings:
Component - 1 – OFF
Component - 2 – OFF
Component - 3 – OFF
2
Select ‘Input Assign’ from the System Setup menu.
If you used component video cords to connect your video
equipment you must tell the receiver which device it is, or
else you may see the S-video or composite video input
instead of the component video signal. For more on this,
see Using the component video jacks on page 14.
System Setup
5.Input Assign
1.Surr Back System
a.Digital Input
b.Component Input
c.HDMI Input
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
1
Select ‘Component Input’ from the Input Assign
:
Exit
:Return
menu.
5. Input Assign
5b.Component Input
Assigning the digital inputs
• Default settings:
a.Digital Input
b.Component Input
c.HDMI Input
Component
Component
Component
-
-
-
1
2
3
OFF
OFF
OFF
[
[
]
]
Coaxial - 1 – DVD/LD
Coaxial - 2 – DVR 2
Optical - 1 – DVR 1
Optical - 2 – TV/SAT
Optical - 3 – CD
:Return
:Finish
2
Select the number of the component video input to
which you’ve connected your video component.
The numbers correspond with the numbers beside the
inputs on the back of the receiver.
You only need to do this if you didn’t hook up your digital
equipment according to the default settings for the
digital inputs (see above). This setting tells the receiver
what digital equipment is hooked up to which terminal so
the buttons on the remote correspond to what you have
hooked up.
3
Select the component that corresponds with the
one you connected to that input.
Select between DVD/LD, TV/SAT, DVR 1, DVR 2 or OFF.
• Use ꢂ/ꢃ and ENTER to do this.
• Make sure you have connected the audio from the
component to the corresponding inputs on the rear
of the receiver.
• If you connect any source component to the receiver
using a component video input, you should also have
your TV connected to this receiver’s component video
MONITORoutput (downconverting component video
is not possible after assigning an input).
1
Select ‘Digital Input’ from the Input Assign menu.
5a.Digital Input Setup
5.Input Assign
a.Digital Input
b.Component Input
c.HDMI Input
Coaxial
Coaxial
Optical
Optical
Optical
-
-
1
2
DVD/LD
[
[
[
[
DVR
DVR
2
1
]
]
]
]
-
1
-
-
2
3
TV/SAT
CD
:Finish
:Return
2
Select the number of the digital input to which
you’ve connected the digital component.
The numbers correspond with the numbers beside the
inputs on the back of the receiver.
4
When you're finished, press RETURN.
You return to the Input Assign menu.
3
Select the component that corresponds with the
one you connected to that input.
Select between DVD/LD, TV/SAT, CD, CD-R, DVR 1,
DVR 2, SIRIUS or OFF.
52
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Settings
09
3
Select the setting you want to adjust.
Assigning the HDMI inputs
If you are doing this for the first time, you may want to
adjust these settings in order:
• Default settings:
HDMI - 1 – DVD/LD
• DRC Setup – Specify the amount of dynamic range
adjustment to Dolby Digital or DTS soundtracks (see
Dynamic Range Control Setup below).
• Dual Mono Setup – Isolate one channel when
listening to discs with dual mono encoding (see Dual
Mono Setup below).
HDMI - 2 – TV/SAT
You only need to change this setting when you didn’t
connect your HDMI component according to the default
settings for the HDMI input terminals (see above). By
specifying the type of the connected component and to
which input terminal it is connected, video signals can be
delivered properly when you select an HDMI component
as the input source.
• LFE ATT Setup – Choose the attenuator level for the
LFE channel (LFE Attenuator Setup on page 54).
1
Select ‘HDMI Input’ from the Input Assign menu.
• SR+ Setup – Specify how you want to control your
Pioneer plasma display (SR+ Setup for Pioneer
plasma displays on page 54).
5. Input Assign
5c.HDMI Input
a.Digital Input
b.Component Input
c.HDMI Input
HDMI
HDMI
-
-
1
2
DVD/LD
TV/SAT
[
]
• Video Conv. Setup – Specify if you want analog
video signals converted for output to your TV (Video
Converter Setup on page 54).
:Return
:Finish
4
Make the adjustments necessary for each setting,
2
Select the number of the HDMI input to which
pressing RETURN to confirm after each screen.
you’ve connected your video component.
The numbers correspond with the numbers beside the
inputs on the back of the receiver.
Dynamic Range Control Setup
• Default setting: OFF
3
Select the component that corresponds with the
This setting specifies the amount of dynamic range
adjustment to Dolby Digital and DTS movie soundtracks.
You may want to use this when listening to surround
sound at low volumes.
one you connected to that input.
Select between DVD/LD, TV/SAT, DVR 1, DVR 2 or OFF.
• Use ꢂ/ꢃ and ENTER to do this.
• To hear audio from your HDMI component (through
this system), you must also make separate audio
connections to the corresponding inputs on the rear
of the receiver. For more on this, see Using SIRIUS
Radio on page 46.
• If you connect any video component to the receiver
using HDMI, you should also have your TV connected
to this receiver’s HDMI output.
1
2
3
Select ‘DRC Setup’ from the Other Setup menu.
6.Other Setup
6a.Dynamic Range Control
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
DRC
OFF
+
d.SR Setup
e.Video Conv. Setup
:Return
:Finish
4
When you're finished, press RETURN.
You return to the Input Assign menu.
Choose the setting that you want.
• OFF – No dynamic range adjustment (use when
listening at higher volume).
• MID – Mid setting.
The Other Setup menu
• MAX – Dynamic range is reduced (loud sounds are
reduced in volume while quieter sounds are
increased).
The Other Setup menu is where you can make
customized settings to reflect how you are using the
receiver.
When you're finished, press RETURN
.
1
Press RECEIVER on the remote control, then press
the SETUP button.
You return to the Other Setup menu.
An on-screen display (OSD) appears on your TV. Use ꢀ/
ꢁ/ꢂ/ꢃ and ENTER to navigate through the screens
and select menu items. Press RETURN to confirm and
exit the current menu.
Dual Mono Setup
•
Default setting: CH1
You can specify how dual mono encoded Dolby Digital
and DTS soundtracks should be played. Dual mono is not
widely used, but is sometimes necessary when two
languages need to be sent to separate channels.
2
Select ‘Other Setup’ then press ENTER.
System Setup
1.Surr Back System
6.Other Setup
a.DRC Setup
2.Auto MCACC
3.Manual MCACC
4.Manual SP Setup
5.Input Assign
6.Other Setup
b.Dual Mono Setup
c.LFE ATT Setup
+
d.SR Setup
e.Video Conv. Setup
:
Exit
:Return
53
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Settings
09
1
Select ‘Dual Mono Setup’ from the Other Setup
2
3
Select the ‘PDP Volume Control’ setting you want.
• OFF – The receiver does not control the volume of the
plasma display
• ON – When the receiver is switched to one of the
inputs that use the plasma display (DVD/LD, or
another function below), the volume on the plasma
display is muted so only sound from the receiver is
heard.
menu.
6.Other Setup
6b.Dual Mono Setup
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
Dual Mono
[
CH1
+
d.SR Setup
e.Video Conv. Setup
:Return
:Finish
Assign any input source connected to the plasma
2
3
Choose the setting that you want.
• CH1 – Only channel 1 is played
• CH2 – Only channel 2 is played
• CH1 CH2 – Both channels are played through the
display to the corresponding input number.
This matches the receiver’s input source with a
numbered video input on the plasma display. For
example, assign DVD/LD to input-2 if you have
connected your DVD video output to video input 2 on the
plasma display.
front speakers
When you're finished, press RETURN
.
• The Monitor Out should be set to the input that
you’ve used to connect this receiver to your plasma
display.
You return to the Other Setup menu.
LFE Attenuator Setup
• Default setting: ATT 0dB
+
+
6d.SR Setup
6d.SR Setup
PDP Volume Control
PDP Volume Control
Some Dolby Digital and DTS audio sources include ultra-
low bass tones. Set the LFE attenuator as necessary to
prevent the ultra-low bass tones from distorting the
sound from the speakers.
[
ON
]
[
ON
]
PDP Input Select
DVD/LD
PDP Input Select
DVD/LD
OFF
OFF
OFF
OFF
OFF
OFF
input-2
OFF
OFF
TV/SAT
[
[
[
[
[
]
]
]
]
]
TV/SAT
[
[
[
[
[
]
]
]
]
]
DVR
DVR
1
2
DVR
DVR
1
2
OFF
VIDEO
VIDEO
OFF
Monitor Out
Monitor Out
OFF
:Finish
:Finish
1
Select ‘LFE ATT Setup’ from the Other Setup menu.
4
When you're finished, press RETURN.
6.Other Setup
6c. LFE ATT Setup
You return to the Other Setup menu.
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
LFE ATT
ATT 0dB
+
d.SR Setup
Video Converter Setup
• Default setting: ON
e.Video Conv. Setup
:Return
:Finish
The video converter allows you to see analog video
sources through all of this receiver’s MONITOR VIDEO
OUT jacks. Note that the converter gives priority to
component, S-video, then composite (in that order). See
About the video converter on page 12 for more on this.
2
3
Choose the setting that you want.
• ATT 0dB – No limiting (recommended)
• ATT 10dB – 10 dB of limiting
• LFE OFF – No sound from LFE channel
1
Select ‘Video Conv. Setup’ from the Other Setup
menu.
When you're finished, press RETURN
.
You return to the Other Setup menu.
6.Other Setup
6e. Video Converter Setup
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
SR+ Setup for Pioneer plasma displays
• Default setting: OFF (all settings)
Video Conv.
ON
+
d.SR Setup
e.Video Conv. Setup
Make the following settings if you have connected a
Pioneer plasma display to this receiver using an SR+
cable. Note that the number of settings available will
depend on the plasma display you’ve connected.
See also Using this receiver with a Pioneer plasma display
on page 50.
:Return
:Finish
2
3
Choose the setting that you want.
• ON – All analog video signals are output from the
MONITOR VIDEO OUT jacks.
• OFF – No conversion between video formats.
1
Select ‘SR+ Setup’ from the Other Setup menu.
When you're finished, press RETURN
.
You return to the Other Setup menu.
+
6d.SR Setup
6.Other Setup
PDP Volume Control
OFF
PDP Input Select
DVD/LD
TV/SAT
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
[
[
[
[
[
[
OFF
OFF
OFF
OFF
OFF
OFF
]
]
]
]
]
]
+
d.SR Setup
e.Video Conv. Setup
DVR
DVR
VIDEO
1
2
Monitor Out
:Finish
:Return
54
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Using other functions
10
Chapter 10:
Using other functions
Refer to the instructions that came with the recorder if
you are unsure how to do this. Most video recorders set
the audio recording level automatically—check the
component's instruction manual if you’re unsure.
Making an audio or a video recording
You can make an audio or a video recording from the
built-in tuner, or from an audio or video source
1
4
Start recording, then start playback of the source
connected to the receiver (such as a CD player or TV).
component.
Keep in mind you can’t make a digital recording from an
analog source or vice-versa, so make sure the
components you are recording to/from are hooked up in
the same way (see Connecting your equipment on
page 11 for more on connections).
Reducing the level of an analog signal
The input attenuator lowers the input level of an analog
signal when it’s too strong. You can use this if you find
the that the OVER indicator is lights often, or you can
Since the video converter is not available when making
recordings (from the video OUT jacks) make sure to use
the same type of video cable for connecting your recorder
as you used to connect your video source (the one you
want to record) to this receiver. For example, you must
connect your recorder using S-video if your source has
also been connected using S-video.
2
hear distortion in the sound.
XM RADIO
DVD
SIRIUS
TV
DVR
2
DVR 1
TV CTRL
RECEIVER
CD-R/TAPE
CD
iPod
TUNER
SB ch
SLEEP
ANALOG
ATT
SR+
DIMMER
MIDNIGHT/
LOUDNESS
For more information about video connections, see
Connecting a DVD/HDD recorder, VCR and other video
sources on page 14.
•
Press RECEIVER then press ANALOG ATT to switch
the input attenuator on or off.
SYSTEM OFF
INPUT
RECEIVER
SOURCE
SELECT
Using the sleep timer
The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
XM RADIO
DVD
SIRIUS
TV
DVR
2
DVR 1
TV CTRL
RECEIVER
CD-R/TAPE
CD
iPod
TUNER
XM RADIO
DVD
SIRIUS
TV
DVR
2
DVR 1
TV CTRL
RECEIVER
1
Select the source you want to record.
CD-R/TAPE
CD
iPod
TUNER
SB ch
Use the input source buttons (or INPUT SELECT).
SLEEP
ANALOG
ATT
• If necessary, press SIGNAL SEL (SIGNAL SELECT) to
select the input signal corresponding to the source
component (see Choosing the input signal on
page 30 for more on this).
SR+
DIMMER
MIDNIGHT/
LOUDNESS
•
Press RECEIVER then press SLEEP repeatedly to set
the sleep time.
2
Prepare the source you want to record.
Tune to the radio station, load the CD, video, DVD etc.
30 min
Off
60 min
90 min
3
Prepare the recorder.
Insert a blank tape, MD, video etc. into the recording
device and set the recording levels.
• You can check the remaining sleep time at any time
by pressing SLEEP once. Pressing repeatedly will
3
cycle through the sleep options again.
Note
1 • The receiver’s volume, DSP (the tone controls, for example), and surround effects have no effect on the recorded signal.
• Some digital sources are copy-protected, and can only be recorded in analog.
• Some video sources are copy-protected. These cannot be recorded.
2 The attenuator isn’t available with digital sources.
3 You can also switch off the sleep timer simply by switching off the receiver.
55
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Using other functions
Dimming the display
10
You can choose between four brightness levels for the
front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
CD-R/TAPE
CD
iPod
SLEEP
TUNER
SB ch
RECEIVER
ANALOG
ATT
SR+
DIMMER
PHASE
MIDNIGHT/
LOUDNESS
DIALOG
E
S.RETRIEVER
•
Press RECEIVER then press DIMMER repeatedly to
change the brightness of the front panel display.
Switching the speaker impedance
We recommend using speakers of 8 Ω with this system,
but it is possible to switch the impedance setting if you
plan to use speakers with a 6 Ω impedance rating. Use
the front panel controls to do this.
•
With the receiver in standby, press ꢀ STANDBY/
ON while holding down the SPEAKERS button.
Each time you do this, you switch between the
impedance settings:
• SP 6 OHM – Use this setting if your speakers are
rated at 6 Ω.
• SP 8 OHM – Use this setting if your speakers are
rated at 8 Ω or more.
Resetting the system
Use this procedure to reset all the receiver’s settings to
the factory default. Use the front panel controls to do this.
1
Switch the receiver into standby.
2
While holding down the front panel TONE button,
press and hold
seconds.
ꢀ
STANDBY/ON for about three
The display shows RESET?.
Press the front panel ENTER button.
The display shows RESET OK?.
Press SYSTEM SETUP to confirm.
3
4
OK appears in the display to indicate that the receiver
has been reset to the factory default settings.
• Note that all settings will be saved, even if the
receiver is unplugged.
56
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the rest of your system
11
Chapter 11:
Controlling the rest of your system
To try out the remote control, switch the component on or
off (into standby) by pressing SOURCE ꢀ. If it doesn’t
seem to work, select the next code from the list (if there
is one).
Setting the remote to control other
components
Most components can be assigned to one of the input
7
If your component is controlled successfully, press
source buttons (such as DVD/LD or CD) using the
component’s manufacturer preset code stored in the
remote.
ENTER to confirm.
The remote LCD display shows OK.
However, there are cases where only certain functions
may be controllable after assigning the proper preset
code, or the codes for the manufacturer in the remote
control will not work for the model that you are using.
Resetting the remote control presets
This will erase all preset remote control preset codes and
programmed buttons.
1
While pressing the RECEIVER button, press SETUP
.
Note
The remote LCD display shows SETUP.
• You can cancel or exit any of the steps by pressing
RECEIVER. To go back a step, press RETURN.
2
Use ꢀ/ꢁ to select RESET then press ENTER
.
RESET flashes in the LCD display.
• After one minute of inactivity, the remote
automatically exits the operation.
3
Press and hold ENTER for about two seconds.
The LCD shows OK to confirm the remote presets have
been erased.
Selecting preset codes directly
XM RADIO
SIRIUS
DVR
2
TOP MENU
MENU
DVD
TV
DVR 1
TV CTRL
Confirming preset codes
ST
ST
T.EDIT
CD-R/TAPE
CD
ENTER
SETUP
GUIDE
RETURN
iPod
TUNER
SB ch
RECEIVER
Use this feature to check which preset code is assigned
to an input source button.
T
SLEEP
ANALOG
ATT
BAND
TV CONTROL
1
While pressing the RECEIVER button, press SETUP
.
1
While pressing the RECEIVER button, press SETUP
.
The remote LCD display shows SETUP.
The remote LCD display shows SETUP.
2
Use ꢀ/ꢁ to select READ ID then press ENTER.
2
3
Use ꢀ/ꢁ to select PRESET then press ENTER
.
The LCD on the remote prompts you for the input source
button you want to check.
Press the input source button for the component
you want to control then press ENTER
.
3
Press the button of the component for which you
The LCD on the remote displays the component you want
want to check the preset code, then press ENTER.
The brand name and preset code appears in the display
for three seconds.
1
to control (for example DVD or DVR).
4
Use ꢀ/ꢁ to select the first letter of the brand name
of your component then press ENTER
.
This should be the manufacturer’s name (for example, P
for Pioneer).
Direct function
• Default setting: ON
5
Use ꢀ/ꢁ to select the manufacturer’s name from
the list then press ENTER
.
You can use the direct function feature to control one
component using the remote control while at the same
time, using your receiver to playback a different
component. This could let you, for example, use the
remote control to set up and listen to a CD on the receiver
and then use the remote control to rewind a tape in your
VCR while you continue to listen to your CD player.
6
Use ꢀ/ꢁ to select the proper code from the list,
then try using this remote with your component.
The code should start with the component type (for
example, DVD 020). If there is more than one, start with
2
the first one.
Note
1 You can’t assign the RECEIVER, TUNER, XM RADIO, SIRIUS or iPod buttons.
2 • When using a Pioneer HDD recorder, please select PIONEER DVR 487, 488, 489 or 493.
• When using a Pioneer plasma display released prior to summer 2005, please select preset codes 637 or 660.
57
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the rest of your system
11
When direct function is on, any component you select
(using the input source buttons) will be selected by both
the receiver and the remote control. When you turn direct
function off, you can operate the remote control without
4
Use ꢀ/ꢁ to select CODE EDT then press ENTER.
To erase any previously stored multi-operations (or
shutdown sequences) select CODE ERS above.
5
Use ꢀ/ꢁ to select a command in the sequence then
1
affecting the receiver.
press ENTER
.
If this is the first command in the sequence, select 1ST
CODE. Otherwise, simply choose the next command in
the sequence. PRES KEY flashes after you press ENTER.
1
While pressing the RECEIVER button, press SETUP
.
The remote LCD display shows SETUP.
2
Use ꢀ/ꢁ to select DIRECT F then press ENTER.
6
If necessary, press the input source button for the
The LCD on the remote prompts you for the button of the
input source you want to control.
component whose command you want to input.
This is only necessary if the command is for a new
component (input source).
3
Press the input source button for the component
you want to control then press ENTER
.
7
Select the button for the command you want to
4
Use ꢀ/ꢁ to switch direct function ON or OFF then
input.
press ENTER
The LCD shows OK to confirm the setting.
.
The following remote control commands can be selected:
SYSTEM OFF
INPUT
RECEIVER
SOURCE
SELECT
Multi Operation and System Off
The Multi Operation feature allows you to program a
series of up to five commands for the components in your
system. For example, you could turn on your TV, turn on
your DVD player and start playing the loaded DVD using
only two buttons on the remote control.
TV CONTROL
INPUT
TV VOL
TV CH
VOL
SELECT
XM RADIO
DVD
SIRIUS
TV
DVR
2
DVR 1
TV CTRL
RECEIVER
CD-R/TAPE
CD
ANT
REC
INFO
iPod
TUNER
SB ch
MUTE
MPX
REC STOP JUKEBOX
SLEEP
ANALOG
ATT
Similar to multi operations, System Off allows you to use
one button to stop and switch off a series of components
in your system at the same time.
AUDIO SUBTITLE
DISP
HDD
CH
DVD
CH
SR+
DIMMER
PHASE
MIDNIGHT/
LOUDNESS
PHOTO
STEREO/
F.S.SURR
THX
STANDARD ADV.SURR
DIALOG
E
S.RETRIEVER
2
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
D.ACCESS
CLASS
DISC
+10
ENTER
SHIFT EFFECT/CH SEL
LEVEL
TOP MENU
MENU
Programming a multi-operation or a
shutdown sequence
TUNE
ST
ST
T.EDIT
ENTER
SETUP
GUIDE
RETURN
RECEIVER
TUNE
BAND
XM RADIO
DVD
SIRIUS
TV
DVR
2
TOP MENU
MENU
DVR 1
TV CTRL
• You don’t need to program the receiver to switch on
or off. This is done automatically.
ST
ST
T.EDIT
CD-R/TAPE
CD
ENTER
SETUP
GUIDE
RETURN
iPod
TUNER
SB ch
RECEIVER
T
SLEEP
ANALOG
ATT
BAND
TV CONTROL
With Pioneer components, you don’t need to:
• program the power to switch off in a shutdown
sequence (except DVD recorders);
1
While pressing the RECEIVER button, press SETUP
.
The remote LCD display shows SETUP.
• program the power to switch on if it’s the source
component selected in step 3;
2
Use ꢀ/ꢁ to select MULTI OP or SYS OFF from the
menu and press ENTER
.
• program a Pioneer TV or monitor to switch on if the
input function (selected in step 2) has video input
terminals;
If you selected Multi Operation (MULTI OP), the LCD on
the remote prompts you for an input source button.
If you selected System Off (SYSOFF), go to step 4.
These take priority in multi operations (not shutdown).
3
Press the input source button for the component
that will start the multi-operation then press ENTER
For example, if you want to start the sequence by
switching on your DVD player, press DVD.
.
Note
1 You can’t use direct function with the TV CTRL function.
2 • Before Multi Operation and System Off will work correctly, you must setup the remote to work with your TV and other components (see Setting the
remote to control other components on page 57 for more on this).
• Some units may take some time to power up, in which case multiple operations may not be possible.
• Power on and off commands only work with components that have a standby mode.
58
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the rest of your system
11
8
Repeat steps 5–7 to program a sequence of up to
• The TV CONTROL buttons on the remote control are
dedicated to control the TV assigned to the TV CTRL
button. If you have two TVs, assign the main TV to the
TV CTRL button.
five commands.
When you’re finished, use ꢀ/ꢁ to select EDITEXIT
from the menu and press ENTER
9
.
You will return to the remote control SETUP menu. Select
* EXIT * again to exit.
Button(s) Function
Components
TVꢀ
Press to switch the component
Cable TV/Satellite
TV/TV/DTV
assigned to the TV CTRL
button on or off.
Using multi operations
You can start multi operations with the receiver switched
on, or in standby.
INPUT
SELECT
Switches the TV input. (Not
possible with all models.)
Cable TV/Satellite
TV/TV/DTV
TV CH +/– Selects channels.
Cable TV/Satellite
TV/TV/DTV
AUDIO SUBTITLE
DISP
HDD
CH
DVD
CH
PHOTO
STEREO/
F.S.SURR
THX
STANDARD ADV.SURR
TV VOL +/– Adjust the TV volume.
Cable TV/Satellite
TV/TV/DTV
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
SHIFT EFFECT/CH SEL
LEVEL
SOURCEꢀ Switches the DTV on or off.
DTV
Switches the TV or CATV between Cable TV/Satellite
standby and on.
TV/TV
RECEIVER
ꢇ
ꢈ
Switches the DTV on or off.
DTV
Press to get information on DTV
programs.
DTV
1
Press MULTI OPE.
MULTI OP flashes in the display.
ꢅ
ꢄ
ꢆ
Use to choose the BLUE
commands on a DTV menu.
DTV
DTV
DTV
DTV
DTV
2
Press an input source button that has been set up
with a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed automatically.
Use to choose the YELLOW
commands on a DTV menu.
Use to choose the GREEN
commands on a DTV menu.
ꢂ
Use to choose the RED
commands on a DTV menu.
Using System off
AUDIO SUBTITLE
DISP
HDD
CH
DVD
CH
AUDIO / DISP Use to switch DTV audio tracks.
SYSTEM OFF
SOURCE
PHOTO
INPUT
STEREO/
F.S.SURR
RECEIVER
THX
STANDARD ADV.SURR
SELECT
SUBTITLE
GUIDE
ANT
Use to return to the previously
selected channel.
Cable TV/Satellite
TV/TV/DTV
MULTI OPE AUTO SURR ACOUSTIC EQ SIGNAL SEL
SHIFT EFFECT/CH SEL
LEVEL
Use as the GUIDE button for
navigating.
Cable TV/Satellite
TV/TV/DTV
Use to select the VHF/UHF
antennas or Cable TV.
Cable TV/TV
XM RADIO
DVD
SIRIUS
TV
DVR
2
RECEIVER
DVR 1
TV CTRL
RETURN
Use to select RETURN or EXIT.
DTV
1
Press MULTI OPE.
Number
buttons
Use to select a specific TV
channel.
Cable TV/Satellite
TV/TV/DTV
MULTI OP flashes in the display.
2
Press ꢀ SOURCE.
+10 button Use to add a decimal point when DTV
selecting a specific TV channel.
The command sequence you programmed will run, then
all Pioneer components will switch off , followed by this
receiver.
1
ENTER/
DISC
Use to enter a channel.
Cable TV/Satellite
TV/TV/DTV
MENU
Select different menus from the
DTV functions.
DTV
Select the menu screen.
Cable TV/Satellite
TV/TV
Controls for TVs
This remote control can control components after
entering the proper codes or teaching the receiver the
commands (see Setting the remote to control other
components on page 57 for more on this). Use the input
source buttons to select the component.
ꢀ/ꢁ/ꢂ/ꢃ Press to select or adjust and
Cable TV/Satellite
TV/TV/DTV
& ENTER
navigate items on the menu
screen.
Note
1 In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
59
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the rest of your system
Controls for other components
11
Button (s) Function
Components
ENTER/
DISC
Chooses the disc.
Multiple CD
player
This remote control can control these components after
entering the proper codes or teaching the receiver the
commands (see Setting the remote to control other
components on page 57 for more on this). Use the input
source buttons to select the component.
Use as the ENTER button.
VCR/DVD player
DVR player
Displays the setup screen for
DVR players.
Changes sides of the LD.
LD player
TOP MENU
MENU
Displays the disc ‘top’ menu of a DVD/DVR
player
Button (s) Function
Components
DVD player.
SOURCEꢀ
Press to switch the component CD/MD/CD-R/
between standby and on.
Displays menus concerning the DVD/DVR
DVD/LD/ DVR
player/VCR/
Cassette deck
current DVD or DVR you are
using.
player
ꢀ
Pauses the tape.
Stops the tape.
Starts playback.
Cassette deck
Cassette deck
Cassette deck
ꢅ
Press to return to the start of the CD/MD/CD-R/
current track or chapter.
Repeated presses skips to the
start of previous tracks or
chapters.
DVD/LD player
ꢁ
ENTER
ꢂ/ꢃ
Fast rewinds/fast forwards the Cassette deck
tape.
ꢄ
Press to advance to the start of CD/MD/CD-R/
the next track or chapter.
Repeated presses skips to the
start of following tracks or
chapters.
DVD/LD player
ꢀ/ꢁ/ꢂ/ꢃ
Navigates DVD menu/options. DVD/DVR
player
&
ENTER
GUIDE
Press to access the DVD player DVD/DVR
setup screen.
player
ꢆ
Pause playback or recording.
CD/MD/CD-R/
DVD/LD/ DVR
player/VCR/
CH +/–
Selects channels.
VCR/DVD/DVR
player
Cassette deck
AUDIO
SUBTITLE
Changes the audio language or DVD/DVR
channel. player
ꢁ
Start playback.
CD/MD/CD-R/
DVD/LD/ DVR
player/VCR/
Displays/changes the subtitles DVD/DVR
Cassette deck
player
on multilingual DVDs.
ꢈ
ꢇ
ꢂ
Hold down for fast forward
playback.
CD/MD/CD-R/
DVD/LD/ DVR
player/VCR/
SHIFT
+SUBTITLE
Switches to the VCR controls
when using a VCR/DVD/HDD
recorder.
VCR/DVD/DVR
player
Cassette deck
HDD (SHIFT
+ CH–)
Switches to the hard disk
controls when using a DVD/
HDD recorder.
DVR player
DVR player
Hold down for fast reverse
playback.
CD/MD/CD-R/
DVD/LD/ DVR
player/VCR/
Cassette deck
DVD(SHIFT
+ CH+)
Switches to the DVD controls
when using a DVD/HDD
recorder.
Stops playback.
CD/MD/CD-R/
DVD/LD/ DVR
player/VCR/
Cassette deck
ì REC
Starts recording.
Stops recording.
MD/CD-R/ DVR
player/VCR/
(SHIFT+ꢁ)
Cassette deck
REC STOP
(SHIFT+ꢂ)
DVR player
JUKEBOX
Switches to the Jukebox feature. DVR player
(SHIFT+
ꢄ)
Number
buttons
Directly access tracks on a
program source.
CD/MD/CD-R/
LD player/VCR
Use the number buttons to
navigate the on-screen
display.
DVD/DVR
player
+10 button
Selects tracks higher than 10.
CD/MD/CD-R/
(For example, press +10 then 3 LD player/VCR
to select track 13.)
60
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the rest of your system
11
Operating other Pioneer components
with this unit’s sensor
Many Pioneer components have SR CONTROL jacks
which can be used to link components together so that
you can use just the remote sensor of one component.
When you use a remote control, the control signal is
1
passed along the chain to the appropriate component.
Important
• Note that if you use this feature, make sure that you
also have at least one set of analog audio, video or
HDMI jacks connected to another component for
grounding purposes.
1
Decide which component you want to use the
remote sensor of.
When you want to control any component in the chain,
this is the remote sensor at which you’ll point the
corresponding remote control.
2
Connect the CONTROL OUT jack of that component
to the CONTROL IN jack of another Pioneer component.
Use a cable with a mono mini-plug on each end for the
connection.
OPTICAL
DIGITAL
OUT
IN
1
COMPONENT VIDE
(
)
DVD/LD
IN
DVR/
VCR1
1
Y
PB
(
IN
1
)
CONTROL
CONTROL
IN
2
IN
2
(
)
TV/SAT
IN
2
(
)
TV/SAT
Y
PB
IN
CD
3
)
(
S
L
E
E
P
IN
OUT
IN
OUT
C
E
I
S
B
V
E
c
h
R
D
I
M
M
E
R
D
.
A
C
C
E
S
S
+
ASSIGNABLE
1
0
OUT
C
L
AS
S
T
U
ENTER
D
I
S
C
SE
TU
P
N
E
S
T
1
3
S-VIDEO
S
T
T
U
HDMI
N
E
R
ET
U
R
N
ASSIG-
NABLE
CONTROL
OUT
iPod
IN
T
H
X
1
2
S
T
A
N
D
A
R
D
A
D
V
.
SU
R
A
U
R
T
O
S
U
R
R
S
T
E
R
E
O
V
XM
IN
R
EC
E
IV
ER
IN
AUDIO
L
IN
OUT
IN
IN
1
(
)
DVD/LD
R
IN
2
(
)
DVR/VCR2
CD
CD-R/TAPE/MD
COAXIAL
ASSIGNABLE
1
2
3
Continue the chain in the same way for as many
components as you have.
Note
1 • If you want to control all your components using this receiver’s remote control, refer to Setting the remote to control other components on page 57.
If you have connected a remote control to the CONTROL IN jack (using a mini-plug cable), you won’t be able to control this unit using the remote sensor.
• See Using this receiver with a Pioneer plasma display on page 50 if you are connecting a Pioneer plasma display.
61
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
12
Chapter 12:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks
listed below, ask your nearest Pioneer authorized independent service company to carry out repair work.
Power
Symptom
Remedy
The power does not turn on.
• Make sure that the power cable is plugged in to an active power outlet.
• Try disconnecting from the power outlet, then plugging back in.
The receiver suddenly switches • Check that there are no loose strands of speaker wire touching the rear panel or another set of wires. If
off or the Phase Control indicator so, re-attach the speaker wires, making sure there are no stray strands.
blinks.
• The receiver may have a serious problem. Disconnect from the power and call a Pioneer authorized
independent service company.
During loud playback the power • Turn down the volume.
suddenly switches off. • Lower the 40 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 36.
• Try switching on the digital safety feature (put the receiver into standby, hold down the SYSTEM SETUP
button on the front panel and press ꢀ STANDBY/ON to switch between SAFETY ON and SAFETY OFF). If
the power switches off even with SAFETY ON selected, turn down the volume.
The unit does not respond when • Try switching the receiver off then back on again.
the buttons are pressed.
• Try disconnecting the power cable, then connect again.
AMP ERR blinks in the display,
then the power automatically
switches off. The MCACC blinks
and the power does not turn on.
• The receiver may have a serious problem. Do not try switching the receiver on. Contact a Pioneer
authorized independent service company for help.
OVERHEAT blinks in the display • Allow the unit to cool down in a well-ventilated place before switching back on. Check the safety
then the power automatically
switches off.
precautions on pages 2 and 3 for information on improving heat dispersal.
No sound
Symptom
Remedy
No sound is output when an input • Check the volume, mute setting (press MUTE) and speaker setting (press SPEAKERS).
source is selected. • Make sure the correct input source is selected.
No sound output from the front • Check that the MCACC setup microphone is disconnected.
speakers.
• Make sure the correct input signal is selected (press SIGNAL SELECT).
• Check that the source component is connected properly (see Connecting your equipment on page 11).
• Check that the speakers are connected properly (see Connecting the speakers on page 18).
No sound from the surround or • Check that the stereo mode or the Front Stage Surround Advance mode isn’t selected; select one of the
center speakers.
surround listening modes (see Listening in surround sound on page 27).
• Check that the surround/center speakers are not set to NO (see Speaker Setting on page 40).
• Check the channel level settings (see Channel Level on page 41).
• Check the speaker connections (see Connecting the speakers on page 18).
62
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
12
Symptom
Remedy
No sound from surround back
speakers.
• Check that the surround back speakers are set to LARGE or SMALL (see Speaker Setting on page 40).
• Make sure surround back processing is set to SBch ON (see Using surround back channel processing on
page 30).
• If the source is Dolby Surround EX or DTS-ES with no flag to indicate 6.1 compatibility, then with surround
back processing set to SBch Auto, there will be no sound from the surround back speakers. In this case,
set to SBch ON (see Using surround back channel processing on page 30).
• If the source does not have 6.1 playback channels, make sure that surround back processing is set to SBch
ON and a surround mode is selected (see Listening in surround sound on page 27).
• Check the speaker connections (see Connecting the speakers on page 18). If only one surround back
speaker is connected, make sure it’s connected to the left channel speaker terminal.
No sound from subwoofer.
• Check that the subwoofer is connected properly, switched on and the volume turned up.
• If your subwoofer has a sleep function, make sure it is switched off.
• Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 40).
• The crossover frequency may be set too low; try setting it higher to match the characteristics of your other
speakers (see Speaker Setting on page 40)
• If there is very little low frequency information in the source material, change your speaker settings to
Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS (see Speaker Setting on page 40).
• Check the speaker level settings (see Channel Level on page 41).
No sound from one speaker.
• Check the speaker connection (see Connecting the speakers on page 18).
• Check the speaker level settings (see Channel Level on page 41).
• Check that the speaker hasn’t been set to NO (see Speaker Setting on page 40).
• The channel may not be recorded in the source. By using one of the advanced effect listening mode, you
may be able to create the missing channel (see Listening in surround sound on page 27).
Sound is produced from analog • Check that the input signal type is set to DIGITAL (see Choosing the input signal on page 30).
components, but not from digital • Make sure that the digital input is assigned correctly for the input jack the component is connected to
ones (DVD, LD, CD-ROM etc.).
(see The Input Assign menu on page 52).
• Check the digital output settings on the source component.
• If the source component has a digital volume control, make sure this is not turned down.
• Make sure that the multichannel analog inputs are not selected. Select any other input source.
No sound is output or a noise is • Check that your DVD player is compatible with Dolby Digital/DTS discs.
output when Dolby Digital/DTS
software is played back.
• Check the digital output settings of your DVD player. Make sure that the DTS signal output is set to On.
• If the source component has a digital volume control, make sure this is not turned down.
Other audio problems
Symptom
Remedy
Broadcast stations cannot be
For FM broadcasts
selected automatically, or there is • Fully extend the FM wire antenna, adjust the position for best reception and secure to a wall, etc.
considerable noise in radio
broadcasts.
• Use an outdoor antenna for better reception (see page 21).
For AM broadcasts
• Adjust the position and direction of the AM antenna.
• Use an outdoor antenna for better reception (see page 21).
• Noise may be caused by interference from other equipment, such as a fluorescent light, motor, etc.
Switch off or move the other equipment, or move the AM antenna.
A multichannel DVD source
appears to be downmixed to 2
channels during playback.
• Make sure that the multichannel analog inputs are selected (see Selecting the multichannel analog inputs
on page 48).
Noise is output when scanning a • This is not a malfunction of the receiver. The scan function of your player alters the digital information,
DTS CD.
making it unreadable, resulting in noise being output. Lower the volume when scanning.
When playing a DTS format LD
there is audible noise on the
soundtrack.
• Make sure that the input signal type is set to DIGITAL (see Choosing the input signal on page 30).
Can’t record audio.
• You can only make a digital recording from a digital source, and an analog recording from an analog
source.
• For digital sources, make sure that what you’re recording isn’t copy protected.
• Check that the OUT jacks are properly connected to the recorders input jacks (see Connecting analog
audio sources on page 17).
63
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
12
Symptom
Remedy
Subwoofer output is very low.
• To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL (see Speaker
Setting on page 40).
Everything seems to be set up
correctly, but the playback sound
is odd.
• The speakers may be out of phase. Check that the positive/negative speaker terminals on the receiver are
matched with the corresponding terminals on the speakers (see Connecting the speakers on page 18).
The PHASE CONTROL feature
• If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to
doesn’t seem to have an audible the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or depending on
effect.
the subwoofer, the setting where you think it has the best overall effect on the sound).
• Make sure the speaker distance setting is correct for all speakers (see Speaker Distance on page 42).
Noise or hum can be heard even • Check that personal computers or other digital components connected to the same power source are not
when there is no sound being
input.
causing interference.
There seems to be a time lag
between the speakers and the
output of the subwoofer.
• See Automatically setting up for surround sound (Auto MCACC) on page 8 to set up your system again
using MCACC (this will automatically compensate for a delay in the subwoofer output).
The maximum volume available • This is not a malfunction. If the levels in Channel Level on page 41 have been adjusted, the maximum
(shown in the front panel display) volume will change accordingly.
is lower than the +12dB
maximum.
Video
Symptom
Remedy
No image is output when an input • Check the video connections of the source component (see page 14).
is selected.
• Make sure the input assignment is correct for components connected using component cables (see The
Input Assign menu on page 52).
• Check the video output settings of the source component.
• Check that the video input you selected on your TV is correct.
• When the source component is connected to this receiver with a component video cable, you must also
connect your TV to this receiver with a component video cable.
Can’t record video.
• Check that the source is not copy-protected.
• The video converter is not available when making recordings. Check that the same type of video cable is
used for connecting both the recorder and the video source (the one you want to record) to this receiver.
Noisy, intermittent, or distorted • Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video
picture.
quality may just be poor (with some video game units, for example). The picture quality may also depend on
the settings, etc. of your display device. Switch off the video converter and reconnect the source and display
device using the same type of connection (component, S-video or composite), then start playback again.
Settings
Symptom
Remedy
The Auto MCACC Setup
continually shows an error.
• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see also
Problems when using the Auto MCACC Setup on page 10). If the noise level cannot be kept low enough, you
will have to set up the surround sound manually (page 36).
After using the Auto MCACC
Setup, the speaker size setting is
incorrect.
• There may have been some low frequency noise in the room from an air-conditioner, motor, etc. Switch
off all other appliances in the room and use Auto MCACC Setup again.
• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some cases.
You can change the speaker setting manually in Speaker Setting on page 40 if this is a recurring problem.
Can’t adjust the Fine Speaker
Distance setting (page 37)
properly.
• Check that the speakers are all in phase (make sure the positive (+) and negative (–) terminals are
matched up properly).
Most recent settings have been • The power cord was disconnected from the wall while adjusting this setting.
erased.
64
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
12
Display
Symptom
Remedy
The display is dark or off.
• Press DIMMER on the remote control repeatedly to select a different brightness.
After making an adjustment the • Press DIMMER on the remote control repeatedly to select a different brightness.
display goes off.
You can’t get DIGITAL to display • Check the digital connections and make sure that the digital inputs are assigned correctly (see The Input
when using the SIGNAL SELECT Assign menu on page 52).
button.
• If the multichannel analog inputs are selected, select a different input source.
The Dolby/DTS indicator doesn’t • These indicators do dot light if playback is paused.
light when playing Dolby/DTS
software.
• Check the playback (especially the digital output) settings of the source component.
When playing a DVD-Audio disc, • This is not a malfunction. 96 kHz audio from DVD-Audio discs is only output from the analog outputs of
the DVD player display shows
96 kHz. However, the receiver’s
display does not.
the DVD player. This receiver cannot show the playback sample rate when using the analog inputs.
During playback of a DTS 96/24 • Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 30).
source, the display doesn’t show
96 kHz.
When playing Dolby Digital or
DTS sources, the receiver’s
format indicators do not light.
• Check that the player is connected using a digital connection.
• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 30).
• Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to PCM.
• Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is selected.
When playing certain discs, none • The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on what audio
of the receiver’s format
indicators light.
tracks are recorded on the disc.
When playing a disc, the
• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 30).
2PL II or Neo:6 indicator lights • If a two channel soundtrack is currently playing (including Dolby Surround encoded), then this is not a
on the receiver.
malfunction. Check the disc packaging for details about the audio tracks available.
During playback of a Surround
• The source may be Dolby Surround EX / DTS-ES software, but it has no flag to indicate it is 6.1
EX or DTS-ES source on the SBch compatible. Set to SBch ON (see Using surround back channel processing on page 30) then switch to the
AUTO setting, the EX and ES
indicators don’t light, or the
signal is not properly processed.
THX Surround EX or Standard EX listening mode (see Listening in surround sound on page 27).
65
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
12
Remote control
Symptom
Remedy
Cannot be remote controlled.
• Try replacing the batteries in the remote control (see Loading the batteries on page 7).
• Be sure to operate within 7 m (23 feet) and a 30º angle of the remote sensor on the front panel (see
Operating range of remote control unit on page 23).
• Check that there are no obstacles between the receiver and the remote control.
• Make sure that there is no fluorescent or other strong light shining on to the remote sensor.
• Check the connections of the CONTROL IN jack (see Operating other Pioneer components with this unit’s
sensor on page 61).
Other components can’t be
operated with the system remote.
• If the battery ran down, the preset codes may have been cleared. Re-enter the preset codes.
• The preset code may be incorrect. Redo the procedure for entering preset codes.
The SR cable is connected, but
the connected components can’t plasma display on page 50).
be operated with the remote.
• Reinsert the SR cable, making sure it’s connected to the right jack (see Using this receiver with a Pioneer
• Make sure that there is an analog or HDMI connection between the units. This is necessary for the SR
feature to work.
• Check that the other component is made by Pioneer. The SR feature only works with Pioneer equipment.
HDMI
Symptom
Remedy
No picture or sound.
• If the problem still persists when connecting your HDMI component directly to your monitor, please
consult the component or monitor manual or contact the manufacturer for support.
No picture.
• Depending in the output settings of the source component, it may be outputting a video format that can’t
be displayed. Change the output settings of the source, or connect using the component, S-video or
composite jacks.
OSD does not appear.
• The OSD will not appear if you have connected using the HDMI output to your TV. Use component, S-video,
or composite connections when setting up the system.
No sound, or sound suddenly
ceases.
• Since the HDMI audio signal is sent through this receiver to your TV, you need to make separate
connections for audio if you want to hear your HDMI component through this system. See Using SIRIUS
Radio on page 46 for more on this.
• If you’ve made separate connections for audio, make sure you have assigned the analog/digital jack(s) to
the corresponding HDMI input for the component. See Assigning the HDMI inputs on page 53 to do this.
• Check the audio output settings of the source component.
iPod messages
Symptom
Error I1
Cause
Action
There is a problem with the signal path from the Switch off the receiver and reconnect the iPod to the receiver.
iPod to the receiver.
If this doesn’t seem to work, try resetting your iPod.
Error I2
The software version being used with the iPod
needs to be updated.
Update the software being used with the iPod (software
versions prior to iPod update 2004-10-20 are not supported).
No Music Track
There are no playable songs currently stored in Input some music files compatible with iPod playback.
the iPod.
66
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
12
XM radio messages
Symptom
Cause
Action
Check Antenna
XM ANT ERR
The XM antenna is not connected.
Check that the XM antenna cable is attached securely.
A short-circuit occurring in the antenna or
surrounding antenna cable.
Make sure that there is nothing unusual with the antenna or
antenna cable. Switch the power off then back on again.
Updating
The radio is being updated with the latest
encryption code.
Wait until the encryption code has been updated. Channels 00
and 01 should function normally.
No Signal
Loading
The XM signal is too weak at the current location. n/a
The receiver is acquiring audio or program
information.
Wait until the information has been received.
Off Air
The channel currently selected has stopped
broadcasting.
Select another channel.
CH– – –
You have selected a channel that does not exist, The receiver will automatically switch to channel 001 (or the
or that you have not subscribed to. last selected channel).
– – – – – – – –
There is no artist name/feature, song/program No action needed.
title, or channel category associated with the
channel at this time.
SIRIUS radio messages
Symptom
Cause
Action
Antenna Error
Check Sirius Tuner
Antenna is not properly connected.
Check that the antenna cable is attached securely.
SIRIUS Connected tuner is not properly
connected.
Check that the 8 pin mini DIN cable and AC Adapter are
attached securely.
Acquiring Signal
The SIRIUS signal is too weak at the current
location.
n/a
Subscription Updating
Updating Channels
Invalid Channel
Unit is updating subscription.
Unit is updating channels.
Wait until the encryption code has been updated.
Wait until the encryption code has been updated.
Selected channel is not available/does not exist. Select another channel.
Note
• If the unit does not operate normally due to external effects such as static electricity disconnect the power plug
from the outlet and insert again to return to normal operating conditions.
67
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
Surround sound formats
12
Manufactured under license from Dolby Laboratories. “Dolby”,
“Pro Logic”, “Surround EX”, and the double-D symbol are
trademarks of Dolby Laboratories.
Below is a brief description of the main surround sound
formats you’ll find on DVDs, satellite, cable and terrestrial
broadcasts, and video cassettes.
DTS
The DTS technologies are explained below. See
Dolby
The Dolby technologies are explained below. See
DTS Digital Surround
DTS Digital Surround is a 5.1-channel audio coding system
from DTS Inc. now widely used for DVD-Video, DVD-Audio,
5.1 music discs, digital broadcasts, and video games. It can
deliver up to six discrete audio channels, comprising five full
range channels, including an LFE channel. Higher sound
quality is achieved through the use of a low compression
rate, and high rates of transmittance during playback.
Dolby Digital
Dolby Digital is a multichannel digital audio coding system
widely used in cinemas, and in the home for DVD and digital
broadcast soundtracks. It can deliver up to six discrete audio
channels, comprising five full range channels and a special
LFE (low frequency effects) channel used mainly for deep,
rumbling sound effects; hence the term “5.1-channel” Dolby
Digital.
DTS-ES
DTS-ES (the ES stands for Extended Surround) is a decoder
that is capable of decoding both DTS-ES Discrete 6.1 and
DTS-ES Matrix 6.1 encoded sources. DTS-ES Discrete 6.1
gives ‘true’ 6.1 channel sound, with a completely separate
(discrete) surround back channel. DTS-ES Matrix 6.1 has a
surround back channel matrixed into the surround left/right
channels. Both sources are also compatible with a
conventional DTS 5.1 channel decoder.
In addition to the format features above, Dolby Digital
decoders offer downmixing for compatibility with mono,
stereo and Dolby Pro Logic audio from a number of bit rates
and channels. Another feature, called Dialog Normalization,
attenuates programs based on the average level of dialog in
a program relative to its peak level (also known as Dialnorm)
in order to achieve uniform playback level.
DTS Neo:6
Dolby Digital Surround EX
DTS Neo:6 can generate 6.1 channel surround sound from
any matrixed stereo source (such as video or TV) and from 5.1
channel sources. It uses both the channel information
already encoded into the source, as well as its own
processing to determine channel localization (with two
channel sources, the “.1” subwoofer channel is generated by
bass management in the receiver). Two modes (Cinema and
Music) are available using DTS Neo:6 with two channel
sources.
Dolby Digital Surround EX (the EX stands for EXtended) is an
extension of Dolby Digital encoding whereby a surround
back channel is matrixed into the surround left/right
channels for 6.1 channel playback. This allows for
compatibility with Dolby Digital 5.1 channel decoding, as
well as for decoding using Dolby Digital EX.
Dolby Pro Logic IIx and Dolby Surround
Dolby Pro Logic IIx is an improved version of the Dolby Pro
Logic II (and Dolby Pro Logic) decoding system. Using the
innovative “steering logic” circuit, this system extracts
surround sound from sources as follows:
DTS 96/24
DTS 96/24 is an extension of the original DTS Digital
Surround which offers high quality 96 kHz/24-bit audio using
a DTS 96/24 decoder. This format is also fully backward
compatible with all existing decoders. This means that DVD
players can play this software using a conventional DTS 5.1
channel decoder.
• Dolby Pro Logic – 4.1 channel sound (mono surround)
from any stereo source
• Dolby Pro Logic II – 5.1 channel sound (stereo
surround) from any stereo source
“DTS” and “DTS-ES | Neo:6” are registered trademarks of DTS,
Inc. “96/24” is a trademark of DTS, Inc.
• Dolby Pro Logic IIx – 6.1 or 7.1 channel sound (stereo
surround and surround back) from two channel or
5.1(and 6.1) channel sources
With two channel sources, the “.1” subwoofer channel is
generated by bass management in the receiver.
Dolby Surround is an encoding system which embeds
surround sound information within a stereo soundtrack,
which a Dolby Pro Logic decoder can then use for enhanced
surround listening with greater sound detail.
68
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
12
Windows MediaTM Audio 9 Professional
Windows Media Audio 9 Professional (WMA9 Pro) is a
discrete surround format developed by Microsoft
Corporation.
•
Timbre Matching
The human ear changes our perception of a sound depending on the
direction from which the sound is coming. In a movie theatre, there is
an array of surround speakers so that the surround information is all
around you. In a home theatre, you use only two speakers located to
the side of your head. The Timbre Matching feature filters the
information going to the surround speakers so that they more closely
match the tonal characteristics of the sound coming from the front
speakers. This ensures seamless panning between the front and
surround speakers.
TM
•
Adaptive Decorrelation
In a movie theatre, a large number of surround speakers help create
an enveloping surround sound experience, but in a home theatre
there are usually only two speakers. This can make the surround
speakers sound like headphones that lack spaciousness and
envelopment. The surround sounds will also collapse into the closest
speaker as you move away from the middle seating position. Adaptive
Decorrelation slightly changes one surround channel’s time and
phase relationship with respect to the other surround channel. This
expands the listening position and creates—with only two speakers—
the same spacious surround experience as in a movie theatre.
WMA9 Pro can support up to 5.1/7.1 channel playback with
sampling rates up to 24-bit/96 kHz. Using the unique WMA
compression techniques, WMA9 Pro can deliver
multichannel music and soundtracks over high-speed
internet networks at low bit rates with minimal audio
degradation. Playback may be enjoyed with the Windows
TM
Media Player 9 Series (or above) and other third-party
media players on a personal computer, or with an AV
amplifier with on-board WMA9 Pro decoding.
•
THX Select2
TM
Windows Media and the Windows logo are trademarks or
Before any home theatre component can be THX Select2 certified, it
must incorporate all the features above and also pass a rigorous
series of quality and performance tests. Only then can a product
feature the THX Select2 logo, which is your guarantee that the Home
Theatre products you purchase will give you superb performance for
many years to come. THX Select2 requirements cover every aspect of
the product including pre-amplifier and power amplifier performance
and operation, and hundreds of other parameters in both the digital
and analog domain.
registered trademarks of Microsoft Corporation in the United
States and/or other countries.
About THX
The THX technologies are explained below. See
•
THX Surround EX
THX Surround EX - Dolby Digital Surround EX is a joint development
of Dolby Laboratories and the THX Ltd. In a movie theater, film
soundtracks that have been encoded with Dolby Digital Surround EX
technology are able to reproduce an extra channel which has been
added during the mixing of the program. This channel, called
Surround Back, places sounds behind the listener in addition to the
currently available front left, front center, front right, surround right,
surround left and subwoofer channels. This additional channel
provides the opportunity for more detailed imaging behind the
listener and brings more depth, spacious ambience and sound
localization than ever before. Movies that were created using the
Dolby Digital Surround EX technology, when released into the home
consumer market may exhibit wording to that effect on the
packaging. A list of movies created using this technology can be
Only receiver and controller products bearing the THX Surround EX
logo, when in the THX Surround EX mode, faithfully reproduce this
new technology in the home.
This product may also engage the “THX Surround EX” mode during
the playback of 5.1 channel material that is not Dolby Digital
Surround EX encoded. In such case the information delivered to the
Surround Back channel will be program dependent and may or may
not be very pleasing depending on the particular soundtrack and the
tastes of the individual listener.
•
THX Cinema processing
THX is an exclusive set of standards and technologies established by
THX Ltd. THX grew from George Lucas’ personal desire to make your
experience of the film soundtrack, in both movie theatres and in your
home theatre, as faithful as possible to what the director intended.
Movie soundtracks are mixed in special movie theatres called
dubbing stages and are designed to be played back in movie theatres
with similar equipment and conditions. This same soundtrack is then
transferred directly onto Laserdisc, VHS tape, DVD, etc., and is not
changed for playback in a small home theatre environment. THX
engineers developed patented technologies to accurately translate
the sound from the movie theatre environment into the home,
correcting the tonal and spatial errors that occur. On this product,
when the THX indicator is on, THX features are automatically added
in Cinema modes (e.g. THX Cinema, THX Surround EX).
•
Re-Equalization
The tonal balance of a film soundtrack will be excessively bright and
harsh when played back over audio equipment in the home because
film soundtracks were designed to be played back in large movie
theaters using very different professional equipment. Re-Equalization
restores the correct tonal balance for watching a movie soundtrack in
a small home environment.
69
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
12
Some Dolby Digital Surround EX soundtracks are missing the digital
flag that allows automatic switching. If you know that the movie that
you are watching is encoded in Surround EX, you can manually select
the THX Surround EX playback mode, otherwise THX Select2 Cinema
mode will apply ASA processing to provide optimum replay.
•
Advanced Speaker Array (ASA)
ASA is a proprietary THX technology which processes the sound fed
to 2 side and 2 back surround speakers to provide the optimal
surround sound experience. When you set up your home theater
system using all eight speaker outputs (Left, Center, Right, Surround
Right, Surround Back Right, Surround Back Left, Surround Left and
Subwoofer) placing the two Surround Back speakers close together
facing the front of the room as shown in the diagram will provide the
largest sweet spot. If for practical reasons you have to place the
Surround Back speakers apart, you will need to go to the THX Audio
Set-up screen and choose the setting that most closely corresponds
to the speaker spacing, which will re-optimize the surround sound-
field.
•
THX MusicMode
For the replay of multi-channel music the THX MusicMode should be
selected. In this mode THX ASA processing is applied to the surround
channels of all 5.1 encoded music sources such as DTS, Dolby Digital
and DVD-Audio to provide a wide stable rear soundstage.
•
THX Games Mode
For the replay of stereo and multi-channel game audio the THX
Games Mode should be selected. In this mode THX ASA processing
is applied to the surround channels of all 5.1 and 2.0 encoded game
sources such as analog, PCM, DTS and Dolby Digital. This accurately
places all game audio surround information, providing a full 360
degree playback environment. THX Games Mode is unique as it gives
you a smooth transition of audio in all points of the surround field.
ASA is used in three new modes; THX Select2 Cinema, THX
MusicMode and THX Games Mode.
•
THX Select2 Cinema mode
THX Select2 Cinema mode plays 5.1 movies using all eight speakers
giving you the best possible movie watching experience. In this mode,
ASA processing blends the side surround speakers and back
surround speakers providing the optimal mix of ambient and
directional surround sounds.
THX and the THX logo are trademarks of THX Ltd. which may be
registered in some jurisdictions. All rights reserved.
DTS-ES (Matrix and 6.1 Discrete) and Dolby Digital Surround EX
encoded soundtracks will be automatically detected in Select2
Cinema mode if the appropriate flag has been encoded.
Listening modes with different input signal formats
The following charts outline the listening modes available with different input signal formats, depending on the surround back
channel processing and decoding method you have selected.
Stereo (2 channel) signal formats
SBch Processing
Input signal format
Standard
THX
Auto Surround
SBch
Processing
ON/AUTO
Dolby Digital Surround
2Pro Logic IIx MOVIE
2Pro Logic IIx MUSIC
2Pro Logic IIx GAME
2Pro Logic IIx MOVIE+THX
2Pro Logic IIx MOVIE
2PRO LOGIC+THXa
Neo:6 CINEMA+THX
THX GAMES MODEb
2PRO LOGICa
Neo:6 CINEMA
Neo:6 MUSIC
(Automatically
selects 6.1/7.1
channel decoding)
DTS Surround
XM Radio
As above
As above
As above
As above
As above
As above
–
Neo:6 CINEMA
XM HD Surround
Stereo playback
Stereo playback
Other stereo sources
PCM 88.2 kHz / 96 kHz
2Pro Logic II MOVIE
2Pro Logic II MUSIC
2Pro Logic II GAME
2PRO LOGICa
SBch
Processing
OFFc
Dolby Digital Surround
2Pro Logic II MOVIE
2Pro Logic II MUSIC
2Pro Logic II GAME
2Pro Logic II MOVIE+THX
2Pro Logic II MOVIE
2PRO LOGIC+THX
Neo:6 CINEMA+THX
(Maximum 5.1
channel playback)
2PRO LOGIC
Neo:6 CINEMA
Neo:6 MUSIC
DTS Surround
As above
As above
As above
As above
–
Neo:6 CINEMA
Stereo playback
Stereo playback
Other stereo sources
PCM 88.2 kHz / 96 kHz
2Pro Logic II MOVIE
2Pro Logic II MUSIC
2Pro Logic II GAME
2PRO LOGIC
a.2PRO LOGIC has a maximum of 5.1 channel playback.
b.Unavailable with only one surround back speaker connected.
c.Automatically selected if no surround back speakers are connected.
70
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
12
Multichannel signal formats
SBch Processing
Input signal format
Standard
THX
Auto Surround
SBch
Processing
ON
WMA9 Pro (6.1/7.1 channel)
Straight decoding
WMA+THX CINEMA
Straight decoding
Dolby Digital EX
(6.1 channel flagged)
Dolby Digital EX
2Pro Logic IIx MOVIEa
2Pro Logic IIx MUSIC
THX SURROUND EX
2Pro Logic IIx MOVIE+THXa
THX Select2 CINEMAa
THX MUSICMODEa
Dolby Digital EX
2Pro Logic IIx
(7.1 channel
decoding used for
all sources)
MOVIEa
THX GAMES MODEa
DTS-ES
(6.1 channel sources/
6.1 channel flagged)
DTS-ES (Matrix/Discrete)
DTS-ES+THX (Matrix/Discrete) DTS-ES (Matrix/Discrete)
DTS 2Pro Logic IIx
MOVIE
THXa
DTS+2Pro Logic IIx
+
MOVIEa
+
THX Select2 CINEMAa
THX MUSICMODEa
THX GAMES MODEa
DTS+2Pro Logic IIx MUSIC
DTS
DTS+Neo:6
DTS+Neo:6
DTS+Neo:6+THX
(5.1 channel encoding)
DTS+2Pro Logic IIx
DTS
+
2Pro Logic IIx
MOVIEa
MOVIE
+
THXa
DTS+2Pro Logic IIx MUSIC
THX Select2 CINEMAa
THX MUSICMODEa
THX GAMES MODEa
Dolby Digital
WMA9 Pro
(5.1 channel encoding)
Dolby Digital EX
THX SURROUND EX
2Pro Logic IIx MOVIE+THXa
THX Select2 CINEMAa
THX MUSICMODEa
Dolby Digital EX
2Pro Logic IIx MOVIEa
2Pro Logic IIx
2Pro Logic IIx MUSIC
MOVIEa
THX GAMES MODEa
DTS 96/24
Straight decoding
(Maximum 5.1 channel
playback)
–
Straight decoding
(Maximum 5.1 channel
playback)
SBch
Processing
AUTO
(Automatically
selects 6.1/7.1
channel
WMA9 Pro (6.1/7.1 channel)
Straight decoding
WMA+THX CINEMA
THX SURROUND EX
Straight decoding
Dolby Digital EX
(6.1 channel flagged)
Dolby Digital EX
2Pro Logic IIx MOVIEa
Dolby Digital EX
2Pro Logic IIx
MOVIEa
DTS-ES (6.1 channel
sources/6.1 channel flagged)
DTS-ES (Matrix/Discrete)
DTS-ES (Matrix/Discrete)
DTS-ES+THX (Matrix/Discrete)
decoding)
Dolby Digital
DTS
WMA9 Pro
Straight decoding
(Maximum 5.1 channel
playback)
Straight decoding
(Maximum 5.1 channel
playback)
THX Select2 CINEMA
(Maximum 5.1 channel
THX CINEMA playback with only
one surround back speaker)
(5.1 channel encoding)
DTS 96/24
Straight decoding
(Maximum 5.1 channel
playback)
–
Straight decoding
(Maximum 5.1 channel
playback)
SBch
Processing
OFFb
(Maximum 5.1
channel
WMA9 Pro (6.1/7.1 channel)
Straight decoding
(Maximum 5.1 channel
playback)
THX CINEMA
THX CINEMA
Straight decoding
(Maximum 5.1 channel
playback)
Dolby Digital EX
(6.1 channel flagged)
DTS-ES (6.1 channel
Straight decoding
Straight decoding
playback)
sources/6.1 channel flagged)
Dolby Digital
DTS
WMA9 Pro
(5.1 channel encoding)
DTS 96/24
Straight decoding
–
Straight decoding
a.Unavailable with only one surround back speaker connected.
b.Automatically selected if no surround back speakers are connected.
71
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
Specifications
12
FM Tuner Section
Frequency Range . . . . . . . . . . . . . . . . . 87.5 MHz to 108 MHz
Usable Sensitivity . . . . . . . Mono: 13.2 dBf, IHF (1.3 µV/75 Ω)
50 dB Quieting Sensitivity . . . . . . . . . . . . . . . Mono: 20.2 dBf
Stereo: 38.6 dBf
Signal-to-Noise Ratio . . . . . . . . . . . . Mono: 73 dB (at 85 dBf)
Stereo: 70 dB (at 85 dBf)
Distortion . . . . . . . . . . . . . . . . . . . . . . . .Stereo: 0.5 % (1 kHz)
Alternate Channel Selectivity . . . . . . . . . . . . 60 dB (400 kHz)
Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . 40 dB (1 kHz)
Frequency Response . . . . . . . . . . . . 30 Hz to 15 kHz 1 dB
Antenna Input . . . . . . . . . . . . . . . . . . . . . . . .75 Ω unbalanced
Amplifier section
Continuous average power output of 120 watts* per
channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no
more than 0.2 %** total harmonic distortion (front).
Continuous Power Output (20 Hz to 20 kHz, 8 Ω, 0.09 %)
Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W + 110 W
Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W
Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W + 110 W
Surround back . . . . . . . . . . . . . . . . . . . . . . . . 110 W + 110 W
AM Tuner Section
Frequency Range . . . . . . . . . . . . . . . . . . 530 kHz to 1700 kHz
Sensitivity (IHF, Loop antenna) . . . . . . . . . . . . . . . . 350 µV/m
Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 dB
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 dB
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loop antenna
Continuous Power Output (1 kHz, 6 Ω, 1.0 %)
Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W + 150 W
Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W
Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W + 150 W
Surround back . . . . . . . . . . . . . . . . . . . . . . . . 150 W + 150 W
Miscellaneous
Total harmonic distortion . . . . . . . . . . . . . . . . . . . . . . . 0.05 %
Power Requirements . . . . . . . . . . . . . . . . . . .AC 120 V, 60 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . . 490 W, 650 VA
In standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 W
AC Outlet . . . . . . . . . . . . . . . . . . . . . . (switched) 100 W MAX.
Dimensions . . . . . . 420 (W) mm x 173 (H) mm x 465 (D) mm
(20 Hz to 20 kHz, 100 W, 8 Ω)
* Measured pursuant to the Federal Trade Commission’s
Trade Regulation rule on Power Output Claims for Amplifiers
** Measured by Audio Spectrum Analyzer
9
13
5
(16 /16 (W) in. x 6 /16 (H) in. x 18 /16 (D) in.)
Weight (without package) . . . . . . . . . . . .15.0 kg (33 lbs 1 oz)
Audio Section
Input (Sensitivity/Impedance)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .335 mV/47 kΩ
Furnished Parts
Setup microphone (for Auto MCACC setup) . . . . . . . . . . . . 1
AA/IEC R6P dry cell batteries . . . . . . . . . . . . . . . . . . . . . . . 2
Remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AM loop antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
These operating instructions
Frequency Response (LINE) . . . . . . 5 Hz to 100 000 Hz dB
Output (Level/Impedance)
REC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 mV/2.2 kΩ
Tone Control
BASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 dB (100 Hz)
TREBLE . . . . . . . . . . . . . . . . . . . . . . . . . . 6 dB (10 kHz)
LOUDNESS . . . . . . . . . . +4 dB / +2 dB (100 Hz/10 kHz)
(at volume position –40 dB)
Note
Signal-to-Noise Ratio (IHF, short circuited, A network)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 dB
Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]
• Specifications and the design are subject to possible
modifications without notice, due to improvements.
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 dB
Composite Video / S-Video Section
Cleaning the unit
Input (Sensitivity/Impedance) . . . . . . . . . . . . . . . .1 Vp-p/75 Ω
Output (Level/Impedance). . . . . . . . . . . . . . . . . . .1 Vp-p/75 Ω
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 dB
Frequency Response . . . . . . . . . . . . . . . . . . . .5 Hz to 10 MHz
• Use a polishing cloth or dry cloth to wipe off dust and
dirt.
• When the surface is dirty, wipe with a soft cloth
dipped in some neutral cleanser diluted five or six
times with water, and wrung out well, and then wipe
again with a dry cloth. Do not use furniture wax or
cleansers.
Component Video Section
Input (Sensitivity/Impedance) . . . . . . . . . . . . . . . .1 Vp-p/75 Ω
Output (Level/Impedance). . . . . . . . . . . . . . . . . . .1 Vp-p/75 Ω
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 dB
Frequency Response . . . . . . . . . . . . . . . . . . .5 Hz to 100 MHz
• Never use thinners, benzine, insecticide sprays or
other chemicals on or near this unit, since these will
corrode the surface.
72
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
12
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will
provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often
undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s
Consumer Electronics Group recommend you avoid
prolonged exposure to excessive noise. This list of
sound levels is included for your protection.
Selecting fine audio equipment such as the unit
you’ve just purchased is only the start of your
musical enjoyment. Now it’s time to consider how
you can maximize the fun and excitement your
equipment offers. This manufacturer and the
Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that
lets the sound come through loud and clear without
annoying blaring or distortion-and, most importantly,
without affecting your sensitive hearing.
Decibel
Level Example
30 Quiet library, soft whispers
40 Living room, refrigerator, bedroom away from traffic
50 Light traffic, normal conversation, quiet office
60 Air conditioner at 20 feet, sewing machine
70 Vacuum cleaner, hair dryer, noisy restaurant
80 Average city traffic, garbage disposals, alarm clock
at two feet.
Sound can be deceiving. Over time your hearing
“comfort level” adapts to higher volumes of sound.
So what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by
setting your equipment at a safe level BEFORE your
hearing adapts.
THE FOLLOWING NOISES CAN BE DANGEROUS
UNDER CONSTANT EXPOSURE
90 Subway, motorcycle, truck traffic, lawn mower
100 Garbage truck, chain saw, pneumatic drill
120 Rock band concert in front of speakers,
thunderclap
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, and without distortion.
140 Gunshot blast, jet plane
180 Rocket launching pad
Once you have established a comfortable sound
level:
• Set the dial and leave it there.
Information courtesy of the Deafness Research Foundation.
Taking a minute to do this now will help to prevent
hearing damage or loss in the future. After all, we
want you listening for a lifetime.
S001_En
73
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Should this product require service in the U.S.A. and you wish to locate the nearest Pioneer
Authorized Independent Service Company, or if you wish to purchase replacement parts,
operating instructions, service manuals, or accessories, please call the number shown
below.
8 0 0 – 4 2 1 – 1 4 0 4
Please do not ship your product to Pioneer without first calling the Customer Support
Division at the above listed number for assistance.
Pioneer Electronics (USA) Inc.
Customer Support Division
P. O. BOX 1760, Long Beach,
CA 90801-1760, U.S.A.
For warranty information please see the Limited Warranty sheet included with your product.
Should this product require service in Canada, please contact a Pioneer Canadian
Authorized Dealer to locate the nearest Pioneer Authorized Service Company in Canada.
Alternatively, please contact the Customer Satisfaction Department at the following address:
Pioneer Electronics of Canada, Inc.
Customer Satisfaction Department
300 Allstate Parkway, Markham, Ontario L3R 0P2
1-877-283-5901
905-479-4411
For warranty information please see the Limited Warranty sheet included with your product.
Si ce produit doit être réparé au Canada, veuillez vous adresser à un distributeur autorisé
Pioneer du Canada pour obtenir le nom du Centre de Service Autorisé Pioneer le plus près
de chez-vous. Vous pouvez aussi contacter le Service à la clientèle de Pioneer:
Pioneer Électroniques du Canada, Inc.
Service Clientèle
300, Allstate Parkway, Markham, Ontario L3R 0P2
1-877-283-5901
905-479-4411
Pour obtenir des renseignements sur la garantie, veuillez vous reporter au feuillet sur la
garantie restreinte qui accompagne le produit.
S018_B_EF
Published by Pioneer Corporation.
Copyright © 2007 Pioneer Corporation.
All rights reserved.
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901, 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270
<07C00001>
Printed in
<ARB7374-A>
Download from Www.Somanuals.com. All Manuals Search And Download.
|