AV Receiver
VSX-522-K
Register your product on
•
Protect your new investment
The details of your purchase will be on file for reference in the event of an insurance claim such as loss or theft.
•
•
Receive free tips, updates and service bulletins on your new product
Improve product development
Your input helps us continue to design products that meet your needs.
•
Receive a free Pioneer newsletter
Registered customers can opt in to receive a monthly newsletter.
Operating Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
This Class B digital apparatus complies with
Canadian ICES-003.
D8-10-1-3_A1_En
11) Only use attachments/accessories specified by
the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
CAUTION
This product satisfies FCC regulations when shielded
cables and connectors are used to connect the unit
to other equipment. To prevent electromagnetic
interference with electric appliances such as radios
and televisions, use shielded cables and connectors
for connections.
D8-10-3a_A1_En
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF
THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.
RECORD THESE NUMBERS ON YOUR ENCLOSED
WARRANTY CARD AND KEEP IN A SAFE PLACE
13) Unplug this apparatus during lightning storms
or when unused for long periods of time.
FOR FUTURE REFERENCE.
D36-AP9-1_A1_En
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product may expose you to chemicals listed on
proposition 65 known to the State of California and
other governmental entities to cause cancer and
birth defect or other reproductive harm.
D3-7-13-69_En
D36-P5_B1_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
period.
K041_A1_En
(Symbol examples for batteries)
The equipment should be disconnected by removing
the mains plug from the wall socket when left unused
for a long period of time (for example, when on
These symbols are only valid
in the European Union.
vacation).
example, when on vacation).
K058c_A1_En
D3-4-2-2-1a_A1_En
D3-4-2-2-2a*_A1_En
Pb
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Thank you for buying this Pioneer product. Please read
through these operating instructions so you will know how to
operate your model properly.
Playing a source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Playing an iPod. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Playing back files stored on an iPod . . . . . . . . . . . . . . . 22
Switches between the iPod controls and the receiver
controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Playing a USB device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Compressed audio compatibility . . . . . . . . . . . . . . . . . . 23
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Improving FM sound . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Listening to station presets . . . . . . . . . . . . . . . . . . . . . . 24
Naming preset stations . . . . . . . . . . . . . . . . . . . . . . . . . 24
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
HDMI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Important information regarding the HDMI
Before you start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Checking what’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . 5
iPod messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
USB messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
About iPod/iPhone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Resetting the main unit. . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Flow of settings on the receiver . . . . . . . . . . . . . . 5
Loading the batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Choosing the listening mode . . . . . . . . . . . . . . . . . . . . . . 25
Listening in surround sound . . . . . . . . . . . . . . . . . . . . . 25
Using the Advanced surround . . . . . . . . . . . . . . . . . . . 26
Using Stream Direct . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Listening with Acoustic Calibration EQ. . . . . . . . . . . . . . . 26
Better sound using Phase Control . . . . . . . . . . . . . . . . . . 27
Setting the Up Mix function . . . . . . . . . . . . . . . . . . . . . . . 27
Connecting the speakers . . . . . . . . . . . . . . . . . . . . . . . . . 11
Making cable connections . . . . . . . . . . . . . . . . . . . . . . . . 12
About HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Analog audio cables . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Digital audio cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
About video outputs connection. . . . . . . . . . . . . . . . . . . . 13
Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connecting an iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Plugging in the receiver . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using the Home Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Speaker Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
The Input Assign menu. . . . . . . . . . . . . . . . . . . . . . . . . . . 32
The Pre Out Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
The Auto Power Down menu . . . . . . . . . . . . . . . . . . . . . . 33
The HDMI Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you start
Flow of settings on the receiver
The unit is a full-fledged AV receiver equipped with an
The Pre Out Setting (page 33)
Checking what’s in the box
Please check that you’ve received the following supplied
accessories:
abundance of functions and terminals. It can be used easily
after following the procedure below to make the connections
and settings.
4 (When connecting the front height speakers.)
The Input Assign menu (page 32)
(When using connections other than the recommended
connections.)
The HDMI Setup menu (page 33)
(When the connected TV supports the HDMI Audio
Return Channel function.)
The colors of the steps indicate the following:
•
•
•
Setup microphone
Remote control
AAA size IEC R03 dry cell batteries (to confirm system
operation) x2
Required setting item
•
•
•
•
•
•
AM loop antenna
FM wire antenna
Warranty card
Quick start guide
Safety Brochure
These operating instructions (CD-ROM)
Setting to be made as necessary
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Use the on-screen automatic MCACC setup to set up
5 your system
Connecting the speakers
1 Where you place the speakers will have a big effect on
•
Automatically setting up for surround sound
(MCACC) (page 18)
the sound.
•
•
Placing the speakers (page 10)
Connecting the speakers (page 11)
Installing the receiver
•
Basic playback (page 20)
Selecting the audio input signal (page 20)
Playing an iPod (page 22)
Playing a USB device (page 23)
Choosing the listening mode (page 25)
6 •
When installing this unit, make sure to put it on a level and
stable surface.
•
•
•
Connecting the components
Don’t install it on the following places:
– on a color TV (the screen may distort)
– near a cassette deck (or close to a device that gives off a
magnetic field). This may interfere with the sound.
– in direct sunlight
– in damp or wet areas
– in extremely hot or cold areas
– in places where there is vibration or other movement
– in places that are very dusty
2 For surround sound, you’ll want to hook up using a
digital connection from the Blu-ray Disc/DVD player to
the receiver.
•
•
About video outputs connection (page 13)
Connecting a TV and playback components
(page 14)
Adjusting the sound as desired
Using the Sound Retriever (page 26)
7 •
•
•
Connecting antennas (page 16)
Plugging in the receiver (page 17)
•
•
•
•
•
•
Better sound using Phase Control (page 27)
Listening with Acoustic Calibration EQ (page 26)
Using surround back channel processing (page 27)
Setting the Up Mix function (page 27)
Setting the Audio options (page 28)
– in places that have hot fumes or oils (such as a kitchen)
Power On
3 Make sure you’ve set the video input on your TV to this
Manual speaker setup (page 30)
receiver. Check the manual that came with the TV if you
don’t know how to do this.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
Controls and displays
1
Front panel
1
2
3
4
5
6
7
8
9
AV RECEIVER VSX-522
16
17
23
18
19 20 18
21
MCACC
HDMI
iPod iPhone
SPEAKERS
DIMMER
DISPLAY
BAND
TUNER EDIT
TUNE
PRESET
ENTER
AUTO SURROUND
STREAM DIRECT STANDARD SURR
/
ALC/
ADVANCED
SURROUND
SOUND
RETRIEVER
STEREO
MASTER
VOLUME
INPUT
SELECTOR
STANDBY/ON
PHONES
MCACC
SETUP MIC
iPod iPhone
USB
24
25 26 27 26 28
22
10
11
12
13 14 15
1
INPUT SELECTOR dial
Selects an input source (page 20).
5
Tuner control buttons
9
10
MASTER VOLUME dial
STANDBY/ON
BAND – Switches between AM, FM ST (stereo) and FM
MONO radio bands (page 24).
2
MCACC indicator
11 PHONES jack
Lights when Acoustic Calibration EQ (page 26) is on (Acoustic
Calibration EQ is automatically set to on after the Auto
MCACC setup (page 18)).
TUNER EDIT – Use with TUNE / PRESET / and
ENTER to memorize and name stations for recall
(page 24).
,
Use to connect headphones. When the headphones are
connected, there is no sound output from the speakers. The
listening mode when the sound is heard from the headphone
can be selected only from PHONES SURR, STEREO or
STEREO ALC mode.
3
Receiver control buttons
TUNE / – Used to find radio frequencies (page 24).
PRESET / – Use to select preset radio stations
(page 24).
SPEAKERS – Use to change the speaker system on or off.
When the SP OFF is selected, no sound is output from the
speakers connected to this receiver.
12 Listening mode buttons
6
HDMI indicator
AUTO SURROUND/STREAM DIRECT– Switches between
Auto surround mode (page 25) and Stream Direct
playback (page 26).
DIMMER – Dims or brightens the display. The brightness
can be controlled in four steps.
Blinks when connecting an HDMI-equipped component;
lights when the component is connected (page 14).
DISPLAY – Switches the display of this unit. The listening
mode, sound volume, Pre Out setting or input name can
be checked by selecting an input source.
• The Pre Out setting may or may not be displayed,
depending on the input source you have selected.
ALC/STANDARD SURR – Press for standard decoding
and to switch between the modes of 2 Pro Logic II, 2
Pro Logic IIx, 2 Pro Logic IIz and NEO:6, and the Auto
level control stereo mode (page 25).
7
iPod iPhone indicator
Lights when an iPod/iPhone is connected and iPod/USB
input is selected (page 22).
8
Remote sensor
ADVANCED SURROUND – Switches between the various
surround modes (page 26).
Receives the signals from the remote control (see Operating
4
Character display
See Display on page 7.
range of remote control on page 9).
STEREO – Press to select stereo playback (page 25).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
1
13 SOUND RETRIEVER
23 DTS indicators
DTS – Lights when a source with DTS encoded audio
signals is detected.
Press to restore CD quality sound to compressed audio
sources (page 26).
14 iPod iPhone USB terminal
HD – Lights when a source with DTS-EXPRESS or DTS-HD
encoded audio signals is detected.
Use to connect your Apple iPod or USB mass storage device
as an audio source (page 17).
ES – Lights to indicate DTS-ES decoding.
15 MCACC SETUP MIC jack
96/24 – Lights when a source with DTS 96/24 encoded
audio signals is detected.
Use to connect a microphone when performing Auto MCACC
setup (page 18).
NEO:6 – When one of the NEO:6 modes of the receiver is
on, this lights to indicate NEO:6 processing (page 25).
Display
24 Dolby Digital indicators
2 D – Lights when a Dolby Digital encoded signal is
detected.
16 PHASE
Lights when the Phase Control is switched on (page 27).
17 AUTO
2 D+ – Lights when a source with Dolby Digital Plus
encoded audio signals is detected.
Lights when the Auto Surround feature is switched on
(page 25).
2HD – Lights when a source with Dolby TrueHD encoded
audio signals is detected.
18 Tuner indicators
ST – Lights when a stereo FM broadcast is being received
in auto stereo mode (page 24).
EX – Lights to indicate Dolby Digital EX decoding.
2PLII(x) – Lights to indicate 2 Pro Logic II/2 Pro Logic
IIx decoding. Light will go off during 2 Pro Logic IIz
decoding (see Listening in surround sound on page 25 for
more on this).
TUNE – Lights when a normal broadcast channel.
PRESET – Shows when a preset radio station is registered
or called.
MEM – Blinks when a radio station is registered.
25 ADV.S.
Lights when one of the Advanced Surround modes has been
selected (see Using the Advanced surround on page 26 for
more on this).
kHz/MHz – Lights when the character display is showing
the currently received AM/FM broadcast frequency.
19 Speaker indicators
26 SIGNAL SELECT indicators
Shows if the speaker system is on or not (page 6).
DIGITAL – Lights when a digital audio signal is selected.
Blinks when a digital audio signal is selected and selected
audio input is not provided.
SPA means the speakers are switched on.
SP means the speakers are switched off.
20 Sleep timer indicator
HDMI – Lights when an HDMI signal is selected. Blinks
when an HDMI signal is selected and selected HDMI input
is not provided.
Lights when the receiver is in sleep mode (page 8).
21 PRESET information or input signal indicator
Shows the preset number of the tuner or the input signal type,
etc.
27 Up Mix/DIMMER indicator
Lights when the Up Mix function is set to ON (page 27). Also,
lights when DIMMER is set to off.
22 Character display
Displays various system information.
28 DIR.
Lights when the DIRECT or PURE DIRECT mode is switched
on (page 26).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
1
As for operating other devices, the remote control codes for
the Pioneer products are preset. The settings cannot be
changed.
9
Receiver and component control buttons
The following button controls can be accessed after you have
Remote control
selected the corresponding input function button (BD DVD,
etc.).
,
1
13
14
1
SLEEP
RECEIVER
SLEEP SOURCE
Press to change the amount of time before the receiver
switches into standby (30 min – 60 min – 90 min – Off). You
can check the remaining sleep time at any time by pressing
SLEEP once.
RECEIVER
first to access:
Press
2
AUDIO PARAMETER – Use to access the Audio options
(page 28).
RECEIVER
3
4
INPUT
HOME MENU – Press to access the Home Menu
(page 30).
2
RECEIVER
Switches the receiver between standby and on.
RETURN – Confirm and exit the current menu screen.
5
3
RECEIVER
Press BD or DVD first to access:
SIGNAL SEL
Switches the remote to control the receiver (used to select the
white commands above the number buttons (MIDNIGHT
TOP MENU – Displays the disc ‘top’ menu of a Blu-ray
Disc/DVD.
,
6
7
etc)). Also use this button to set up surround sound (page 30)
or Audio parameters (page 28).
HOME MENU – Displays the HOME MENU screen.
RETURN – Confirm and exit the current menu screen.
MENU – Displays the TOOLS menu of Blu-ray Disc player.
Press TUNER first to access:
4
INPUT SELECT
Use to select the input source (page 20).
8
5
Input function buttons
AUDIO
TOOLS
MENU
PARAMETER
TOOLS – Memorizes stations for recall, also used to
change the name (page 24).
Use to select the input source to this receiver (page 20). This
will enable you to control other Pioneer components with the
remote control.
U
N
E
T
TOP
MENU
9
P
BAND – Switches between AM, FM ST (stereo) and FM
MONO radio bands (page 24).
T
R
E
S
S
ENTER
E
15
16
R
T
6
SIGNAL SEL
P
Press iPod/USB first to access:
10
Press to select the audio input signal of the component to play
HOME
MENU
back (page 20).
iPod CTRL – Switches between the iPod controls and the
receiver controls (page 22).
T
E
PTY
BAND
RETURN
iPod CTRL
7
8
Sound control buttons
MUTE
10 /// (TUNE /, PRESET /), ENTER
Acous.EQ – Press to switch on/off Acoustic Calibration
EQ setting (page 26).
Use the arrow buttons when setting up your surround sound
system (page 30). Also used to control Blu-ray Disc/DVD
menus/options.
11
12
S.RETRIEVER – Press to restore CD quality sound to
compressed audio sources (page 26).
Use TUNE / can be used to find radio frequencies and
PRESET / can be used to select preset radio stations
(page 24).
PHASE – Press to switch on/off Phase Control (page 27).
DISP
CH
1
4
2
5
8
0
3
6
17
Listening mode buttons
AUTO/DIRECT – Switches between Auto surround mode
(page 25) and Stream Direct playback (page 26).
CH
7
9
CLR
ENTER
STEREO – Press to select stereo playback (page 25).
ALC/STANDARD SURR – Press for standard decoding
and to switch between the modes of 2 Pro Logic II, 2
Pro Logic IIx, 2 Pro Logic IIz and NEO:6, and the Auto
level control stereo mode (page 25).
RECEIVER
ADV SURR – Switches between the various surround
modes (page 26).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
1
11 Component control buttons
VOL +/– – Use to adjust the volume on your TV.
Operating range of remote control
The remote control may not work properly if:
The main buttons (
,
, etc.) are used to control a component
15 VOLUME +/–
after you have selected it using the input function buttons.
The controls above these buttons can be accessed after you
have selected the corresponding input function button (BD
DVD and CD). These buttons also function as described
below.
Use to set the listening volume.
•
•
•
•
There are obstacles between the remote control and the
receiver’s remote sensor.
Direct sunlight or fluorescent light is shining onto the
remote sensor.
The receiver is located near a device that is emitting
infrared rays.
The receiver is operated simultaneously with another
infrared remote control unit.
16 MUTE
,
Mutes/unmutes the sound.
17 DISP
RECEIVER
Switches the display of this unit. The listening mode, sound
volume, Pre Out setting or input name can be checked by
selecting an input source.
Press
first to access:
BASS +/–
,
TRE +/– – Use to adjust Bass or Treble.
• These controls are disabled when the listening mode is
set to DIRECT or PURE DIRECT.
• When the front speaker is set at SMALL in the Speaker
Setting (or automatically via the Auto MCACC setup)
and the X.Over is set above 150 Hz, the subwoofer
channel level will be adjusted by pressing BASS +/–
(page 31).
•
The Pre Out setting may or may not be displayed,
depending on the input source you have selected.
Loading the batteries
12 Number buttons and other component controls
Use the number buttons to directly select a radio frequency
(page 24) or the tracks on a CD, etc. There are other buttons
30°
30°
that can be accessed after
is pressed. (For example
RECEIVER
MIDNIGHT, etc.)
The batteries included with the unit are to check initial
operations; they may not last over a long period. We
recommend using alkaline batteries that have a longer life.
7 m (23 ft.)
SB CH – Press to select ON, AUTO or OFF the surround
back channel (page 27).
CH SELECT – Press repeatedly to select a channel, then
use LEV +/– to adjust the level (page 31).
CAUTION
LEV +/– – Use to adjust the channel level.
•
Incorrect use of batteries may result in such hazards as
leakage and bursting. Observe the following precautions:
MIDNIGHT – Switches to Midnight or Loudness listening
(page 28).
-
-
Never use new and old batteries together.
Insert the plus and minus sides of the batteries properly
according to the marks in the battery case.
SPEAKERS – Use to change the speaker system on or off.
When the SP OFF is selected, no sound is output from the
speakers connected to this receiver.
-
-
Batteries with the same shape may have different
voltages. Do not use different batteries together.
When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country or area.
DIMMER – Dims or brightens the display. The brightness
can be controlled in four steps.
13
SOURCE
Turns on or off the power of the Pioneer DVD/DVR units when
BD DVD or CD is selected using the input function buttons.
-
Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the life or
performance of batteries.
,
14 TV CONTROL buttons
These buttons can control only be used with Pioneer TVs.
– Use to turn on/off the power of the TV.
INPUT – Use to select the TV input signal.
CH +/– – Use to select channels.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
Connecting your equipment
2
Hints on the speaker placement
Where you put your speakers in the room has a big effect on the quality of the sound. The
following guidelines should help you to get the best sound from your system.
Placing the speakers
By connecting the left and right front speakers (L/R), the center speaker (C), the left and right
surround speakers (SL/SR), and the subwoofer (SW), a 5.1 ch surround system can be enjoyed.
Further, by using an external amplifier, you can connect the left and right surround back
speakers (SBL/SBR) or the left and right front height speaker (FHL/FHR) to boost your system
up to a 7.1 ch surround system.
•
The subwoofer can be placed on the floor. Ideally, the other speakers should be at about ear-
level when you’re listening to them. Putting the speakers on the floor (except the subwoofer),
or mounting them very high on a wall is not recommended.
•
•
•
•
For the best stereo effect, place the front speakers 2 m to 3 m (6 ft. to 9 ft.) apart, at equal
distance from the TV.
If you’re going to place speakers around your CRT TV, use shielded speakers or place the
speakers at a sufficient distance from your CRT TV.
If you’re using a center speaker, place the front speakers at a wider angle. If not, place them
at a narrower angle.
Place the center speaker above or below the TV so that the sound of the center channel is
localized at the TV screen. Also, make sure the center speaker does not cross the line formed
by the leading edge of the front left and right speakers.
•
You can also connect one surround back speaker (SB) and enjoy a 6.1 ch surround system.
To achieve the best possible surround sound, install your speakers as shown below.
6.1 channel surround
5.1 channel surround system:
(Surround back) system: a
R
R
L
L
C
C
•
•
It is best to angle the speakers towards the listening position. The angle depends on the size
of the room. Use less of an angle for bigger rooms.
Surround and surround back speakers should be positioned 60 cm to 90 cm (2 ft. to 3 ft.)
higher than your ears and titled slight downward. Make sure the speakers don’t face each
other. For DVD-Audio, the speakers should be more directly behind the listener than for
home theater playback.
120
SW
120
120
SW
120
SR
SR
SB
SL
SL
•
If the surround speakers cannot be set directly to the side of the listening position with a 7.1-
channel system, the surround effect can be enhanced by turning off the Up Mix function (see
Setting the Up Mix function on page 27).
7.1 channel surround
7.1 channel surround
(Surround back) system: a
(Front height) system: a
•
•
Try not to place the surround speakers farther away from the listening position than the front
and center speakers. Doing so can weaken the surround sound effect.
Place the left and right front height speakers at least one meter directly above the left and
right front speakers.
FHR
R
FHL
R
L
L
C
C
SR
90
CAUTION
SW
SW
120
120
90
•
•
Make sure that all speakers are securely installed. This not only improves sound quality, but
also reduces the risk of damage or injury resulting from speakers being knocked over or
falling in the event of external shocks such as earthquakes.
SBR
SR
SL
60
SL
SBL
Important
To connect the surround back or front height speakers, an additional amplifier is required.
Connect the additional amplifier to the PRE OUT SURR BACK/FRONT HEIGHT outputs of
this unit and connect the surround back or front height speakers to the additional amplifier
(see Connect the surround back or front height speakers on page 11).
a. This layout is available only when the additional amplifier is connected to the unit and the surround
back or front height speakers are connected to the amplifier. For details, see Connect the surround
back or front height speakers on page 11.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
2
Front right
Subwoofer
Front left
Connecting the speakers
Center
The receiver will work with just two stereo speakers (the front speakers in the diagram) but
using at least three speakers is recommended, and a complete setup is best for surround
sound.
LINE LEVEL
INPUT
Make sure you connect the speaker on the right to the right (R) terminal and the speaker on the
left to the left (L) terminal. Also make sure the positive and negative (+/–) terminals on the
receiver match those on the speakers.
You can use speakers with a nominal impedance between 6 Ω and 16 Ω.
Be sure to complete all connections before connecting this unit to the AC power source.
ASSIGNABLE
OUT
HDMI
IN
IN
Bare wire connections
1
IN
1
CD
COAXIAL
ASSIGNABLE
PREOUT
)
(
)
DVD
SAT/CBL
GAME
B
SUBWOOFOEPRTICAL
Front speaker terminals:
1
2
3
3
PRE OUT
SUB WOOFER
1
2
3
Twist exposed wire strands together.
Loosen terminal and insert exposed wire.
Tighten terminal.
SURR BACK/
10 mm
( /8 in.)
FRONT HEIGHT
)
(L
Single
FRONT
ANTENNA
3
PRE OUT
R
L
CENTER
SURROUND
R
AM LOOP
R
L
PREOUT
Center and surround speaker terminals:
1
2
SURR BACK/
1
2
Twist exposed wire strands together.
FRONT HEIGHT
MONITOR SAT/CBL DVD
R
OUT
IN
IN
FM UNBAL
75
(
)
1
DVD SAT/CBL ANALOG IN CD
ASSIGNABLE
Push open the tabs and insert exposed
wire.
CAUTION:
ATTENTION:
SPEAKER IMPEDANCE ENCEINTE D’IMPEDA
10 mm
ClaFRONTSPEAKERS
SURROUND
A
VIDEO
AUDIO
.
6
-16
.
CENTER
3
R
L
R
L
( /8 in.)
3
•
•
Release the tabs.
Surround left
Surround right
CAUTION
These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric
shock when connecting or disconnecting the speaker cables, disconnect the power cord
before touching any uninsulated parts.
Make sure that all the bare speaker wire is twisted together and inserted fully into the
speaker terminal. If any of the bare speaker wire touches the back panel it may cause the
power to cut off as a safety measure.
Surround back or
front height speakers
Connect the surround back or front height speakers
Connect the PRE OUT SURR BACK/FRONT HEIGHT outputs of the unit and additional
Right
Left
amplifier to add a surround back or front height speaker.
•
The Pre Out setting must be set if the above connections are performed. Select Surr.Back if
the surround back speaker is connected and Height if the front height speaker is connected
(If neither the surround back speaker nor the front height speaker is connected, either
setting will suffice) (see The Pre Out Setting on page 33).
R
L
ANALOG
AUDIO IN
SPEAKER
R
SPEAKER
L
•
You can use the additional amplifier on the surround back channel pre-outs for a single
speaker as well. In this case plug the amplifier into the left (L (Single)) terminal only.
Surround back or front height
channel amplifier
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
2
•
•
If the video signal does not appear on your TV, try adjusting
the resolution settings on your component or display. Note
that some components (such as video game units) have
resolutions that may not be displayed. In this case, use a
(analog) composite connection.
When the video signal from the HDMI is 480i, 480p, 576i or
576p, Multi Ch PCM sound and HD sound cannot be
received.
Note
Making cable connections
•
Use a High Speed HDMI® cable. If HDMI cable other than
a High Speed HDMI® cable is used, it may not work
properly.
Make sure not to bend the cables over the top of this unit (as
shown in the illustration). If this happens, the magnetic field
produced by the transformers in this unit may cause a
humming noise from the speakers.
•
•
When an HDMI cable with a built-in equalizer is connected,
it may not operate properly.
3D, Deep Color, x.v.Color signal transfer and Audio Return
Channel are only possible when connected to a compatible
component.
HDMI format digital audio transmissions require a longer
time to be recognized. Due to this, interruption in the audio
may occur when switching between audio formats or
beginning playback.
Turning on/off the device connected to this unit’s HDMI
OUT terminal during playback, or disconnecting/
connecting the HDMI cable during playback, may cause
noise or interrupted audio.
About HDMI
•
•
The HDMI connection transfers uncompressed digital video,
as well as almost every kind of digital audio that the
connected component is compatible with, including DVD-
Video, DVD-Audio, SACD, Dolby Digital Plus, Dolby TrueHD,
DTS-HD Master Audio (see below for limitations), Video CD/
Super VCD and CD.
Important
•
•
Before making or changing connections, switch off the
power and disconnect the power cord from the AC outlet.
Before unplugging the power cord, switch the power into
standby.
This receiver incorporates High-Definition Multimedia
Interface (HDMI®) technology.
HDMI, the HDMI Logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing, LLC in the United States and other countries.
This receiver supports the functions described below through
HDMI connections.
•
Digital transfer of uncompressed video (contents protected
by HDCP (1080p/24, 1080p/60, etc.))
3D signal transfer
Deep Color signal transfer
x.v.Color signal transfer
Audio Return Channel (see The HDMI Setup menu on
HDMI cables
“x.v.Color” and
Corporation.
are trademarks of Sony
Both video and sound signals can be transmitted
simultaneously with one cable. If connecting the player and
the TV via this receiver, for both connections, use HDMI
cables.
•
•
•
•
page 33)
•
•
Input of multi-channel linear PCM digital audio signals
(192 kHz or less) for up to 8 channels
Input of the following digital audio formats:
– Dolby Digital, Dolby Digital Plus, DTS, High bitrate audio
(Dolby TrueHD, DTS-HD Master Audio), DVD-Audio, CD,
SACD (DSD 2 ch only), Video CD, Super VCD
HDMI
Be careful to connect the terminal in the proper direction.
Note
•
Set the HDMI parameter in Setting the Audio options on
page 28 to THRU (THROUGH) and set the input signal in
Selecting the audio input signal on page 20 to HDMI, if you
want to hear HDMI audio output from your TV (no sound
will be heard from this receiver).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
2
Analog audio cables
Standard RCA video cables
About video outputs connection
This receiver is not loaded with a video converter. When you
use HDMI cables for connecting to the input device, the same
cables should be used for connecting to the TV.
The signals input from the analog (composite) video inputs of
this unit will not be output from the HDMI OUT.
Use stereo RCA phono cables to connect analog audio
components. These cables are typically red and white, and
you should connect the red plugs to R (right) terminals and
white plugs to L (left) terminals.
These cables are the most common type of video connection
and are used to connect to the composite video terminals. The
yellow plugs distinguish them from cables for audio.
VIDEO
L
White (Left)
A
UDIO
Playback component
Yellow
R
Red (Right)
Digital audio cables
IN
IN
Terminal for connection with
source device
Commercially available coaxial digital audio cables or optical
cables should be used to connect digital components to this
receiver.
HDMI
VIDEO
CO
AXIAL
IN
Coaxial digital
audio cable
OPTICAL
IN
MONITOR
OUT
OUT
Terminal for connection
with TV monitor
HDMI
VIDEO
Optical cable
The OSD will
not appear.
Note
•
When connecting optical cables, be careful when inserting
the plug not to damage the shutter protecting the optical
socket.
•
•
When storing optical cable, coil loosely. The cable may be
damaged if bent around sharp corners.
You can also use a standard RCA video cable for coaxial
digital connections.
TV
Video signals can be output.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
2
Game console
HDMI/DVI-compatible components
Connecting a TV and playback components
Connecting using HDMI
DVD player,
Blu-ray Disc player,
Blu-ray Disc recorder
Set-top box
HDD/DVD recorder
If you have an HDMI or DVI (with HDCP) equipped component
(Blu-ray Disc player, etc.), you can connect it to this receiver
using a commercially available HDMI cable.
•
The following connection/setting is required to listen to the
sound of the TV over this receiver.
HDMI OUT
HDMI OUT
HDMI OUT
-
If the TV does not support the HDMI Audio Return
Channel function, connect the receiver and TV with audio
cables (as shown).
-
If the TV supports the HDMI Audio Return Channel
function, the sound of the TV is input to the receiver via
the HDMI terminal, so there is no need to connect an
audio cable. In this case, set ARC at HDMI Setup to ON
(see The HDMI Setup menu on page 33).
If the TV does not support
the HDMI Audio Return
Channel function, this
connection is required to
listen to the TV sound over
the receiver.
HDMI
OUT
OPTICAL
IN1 (TV)
Important
ASSIGNABL
OUT
HDMI
IN
IN
•
•
If the receiver is connected to a TV using an HDMI cable,
the on-screen display (OSD) will not be displayed. Be sure
to use a standard RCA analog video cable to connect. In
this case, switch the TV input to analog to see the OSD
screen (for setup, etc.) on the TV.
When the ARC function is ON and the receiver is
connected to a compatible TV with an HDMI cable, and you
switch the input of the TV to composite, the input of the
receiver may automatically switch to TV. If this happens,
switch the receiver’s input back to the original input, or turn
OFF the ARC function (see The HDMI Setup menu on
page 33).
DVD IN
IN
1
TV
GNABLE
(
)
(
S
DVD
SAT/CBL
GAME
BD
OPTICAL COA
PR
SUB
SAT/CBL IN
BD IN
GAME IN
SURR BACK/
FRONT HEIGHT
(L
)
Single
FRONT
ANTENNA
AM LOOP
PRE OUT
R
L
MONITOR
OUT
CENTER
SURROUND
R
R
L
L
IN
R
MONITOR SAT/CBL DVD
OUT
IN
IN
Note
FM UNBAL
75
( )
DVD SAT/CBL ANALOG IN CD
ASSIGNABLE
1
CAUTION:
ATTENTIO
SPEAKER IMPEDANCE ENCEINTE D’IMP
Class 2 Wiring
SPEAKERS
A
•
In order to listen to the audio from the TV that is connected
to this receiver using an analog audio cables, set-up for
analog audio input is required (see The Input Assign menu
on page 32).
VIDEO
AUDIO
6
-16
.
6
-16
.
ANALOG
IN1 (CD)
This connection is
necessary in order to
see the OSD of the
unit on the TV.
R
L
HDMI IN
OPTICAL
ANALOG AUDIO OUT DIGITAL AUDIO OUT
Select one
VIDEO IN
HDMI/DVI-compatible TV
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
2
Connecting your component with no HDMI
terminal
This diagram shows connections of a TV and DVD player (or
other playback component) with no HDMI terminal to the
receiver.
DVD player
Set-top box
Select one
DIGITAL AUDIO OUT
OPTICAL COAXIAL
Select one
ANALOG AUDIO OUT DIGITAL AUDIO OUT
VIDEO OUT
VIDEO OUT
ANALOG AUDIO OUT
Note
R
L
R
L
OPTICAL
COAXIAL
•
In order to listen to the audio from the TV that is connected
to this receiver using a analog audio cables, set-up for
analog audio input is required (see The Input Assign menu
on page 32).
•
You can only connect one component to the optical input
terminal. If connecting other devices, please use a different
method to connect the audio.
This connection is
required in order to
listen to the sound of
the TV over the
In order to listen to the audio from the source component
that is connected to this receiver using an optical cable,
first, switch to the DVD (DVD player) or SAT/CBL (set-top
box), then press SIGNAL SEL to choose the audio signal
O1 (OPTICAL1) (see Selecting the audio input signal on
page 20
receiver.
ASSE
O
HDMI
IN
IN
COAXIAL
ASSIGIN1 (CD)
•
You can only connect one component to the coaxial input
terminal. If connecting other devices, please use a different
method to connect the audio.
In order to listen to the audio from the source component
that is connected to this receiver using a coaxial cable, first,
switch to the DVD (DVD player) or SAT/CBL (set-top box),
then press SIGNAL SEL to choose the audio signal C1
(COAXIAL1) (see Selecting the audio input signal on
page 20.
IN
(
1
)
IN
(
1
CD
)
TV
DVD
SAT/CBL
GAME
BD
OPTICAL COAXIAL
RE OUT
OPTICAL
IN1 (TV)
SURR BACK/
FRONT HEIGHT
(L
)
Single
FRONT
ANTENNA
AM LOOP
PRE OUT
R
L
MONITOR
OUT
CENTER
SURROUND
R
R
L
L
IN
R
MONITOR
OUT
SAT/CBL
IN
DVD
IN
FM UNBAL
75
( )
ANALOG IN CD
ASSIGNABLE
DVD
SAT/CBL
1
CAUTION:
ATTENTIO
SPEAKER IMPEDANCE ENCEINTE D’IMP
Class 2 Wiring
SPEAKERS
A
DVD IN
V
AUDIO
6
-16
.
6
-16
.
ANALOG
IN1 (CD)
SAT/CBL IN
R
L
OPTICAL
ANALOG AUDIO OUT DIGITAL AUDIO OUT
VIDEO IN
Select one
TV
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
2
3
Place the AM antenna on a flat surface and in a direction
giving the best reception.
For the best possible reception, suspend horizontally
outdoors.
Connecting antennas
Connect the AM loop antenna and the FM wire antenna as
shown below. To improve reception and sound quality,
connect external antennas (see Using external antennas
below).
4
Connect the FM wire antenna into the FM antenna
socket.
ANTENNA
For best results, extend the FM antenna fully and fix to a wall
or door frame. Don’t drape loosely or leave coiled up.
Outdoor
antenna
AM LOOP
fig. b
fig. a
Using external antennas
To improve FM reception
Use an F connector (not supplied) to connect an external FM
antenna.
5 m to 6 m
(16 ft. to 20 ft.)
Indoor antenna
(vinyl-coated wire)
2
ANTENNA
AM LOOP
F connector
FM UNBAL
75
4
3
FM UNBAL
75
To improve AM reception
1
Connect a 5 m to 6 m (16 ft. to 20 ft.) length of vinyl-coated
wire to the AM antenna terminal without disconnecting the
supplied AM loop antenna.
1
Push open the tabs, then insert one wire fully into each
terminal, then release the tabs to secure the AM antenna
wires.
2
Fix the AM loop antenna to the attached stand.
To fix the stand to the antenna, bend in the direction indicated
by the arrow (fig. a) then clip the loop onto the stand (fig. b).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
2
•
When the ARC function is ON and the receiver is
connected to a compatible TV with an HDMI cable, and you
switch the input of the TV when the receiver’s selection is
iPod/USB input, the receiver may automatically switch to
TV. If this happens, switch the receiver's input back to the
original input, or turn OFF the ARC function (see The HDMI
Setup menu on page 33).
Connecting an iPod
This receiver has a dedicated iPod terminal that will allow you
to control playback of audio content from your iPod using the
controls of this receiver.
Plugging in the receiver
Only plug in after you have connected all your components to
this receiver, including the speakers.
Plug the AC power cord into a convenient AC power
outlet.
Switch the receiver into standby, and then use the USB
cable (for iPod connection) to connect your iPod to the iPod
iPhone USB terminal on the front panel of this receiver.
CAUTION
•
Handle the power cord by the plug part. Do not pull out the
plug by tugging the cord, and never touch the power cord
when your hands are wet, as this could cause a short
circuit or electric shock. Do not place the unit, a piece of
furniture, or other object on the power cord or pinch the
cord in any other way. Never make a knot in the cord or tie
it with other cables. The power cords should be routed so
that they are not likely to be stepped on. A damaged power
cord can cause a fire or give you an electric shock. Check
the power cord once in a while. If you find it damaged, ask
your nearest Pioneer authorized independent service
company for a replacement.
•
The USB cable (for iPod connection) is not included with
this receiver. For the cable connection, refer to also the
operating instructions for iPod.
Connecting a USB device
It is possible to listen to two-channel audio using the USB
interface on the front of this receiver.
•
For instructions on playing the iPod, see Playing an iPod on
page 22.
Switch the receiver into standby then connect your USB
device to the USB terminal on the front panel of this
receiver.
AV RECEIVER VSX-522
•
•
This receiver does not support a USB hub.
For instructions on playing the USB device, see Playing a
USB device on page 23.
HDMI
iPod iPhone
AV RECEIVER VSX-522
PRESET
ENTER
•
•
The receiver should be disconnected by removing the
mains plug from the wall socket when not in regular use,
e.g., when on vacation.
SOUND
RETRIEVER
HDMI
iPod iPhone
MASTER
VOLUME
Note
PRESET
ENTER
After this receiver is connected to an AC outlet, a 2 second
to 10 second HDMI initialization process begins. You
cannot carry out any operations during this process. The
HDMI indicator in the front panel display blinks during this
process, and you can turn on this receiver once it has
stopped blinking. When you set ARC at HDMI setup to OFF,
you can skip this process. For details, see The HDMI Setup
menu on page 33.
MCACC
SETUP MIC
iPod iPhone
USB
SOUND
RETRIEVER
MASTER
VOLUME
MCACC
SETUP MIC
iPod iPhone
USB
This receiver
USB cable
(for iPod connection)
This receiver
USB mass
storage device
iPod/iPhone
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
Basic Setup
3
If you have a tripod, use it to place the microphone so that
it’s about ear level at your normal listening position.
Otherwise, place the microphone at ear level using a
table or a chair.
Canceling the demo display
The display on the front panel shows various information
(demo displays) when the receiver is not operating.
You can turn off the demo display. For details, see The FL
Demo Mode menu on page 33.
RECEIVER
Press
on the remote control, then press the
4
5
HOME MENU button.
•
The demo mode is canceled automatically when the Auto
MCACC setup is performed (see below).
The Home Menu appears on your TV. Use ///and
ENTER on the remote control to navigate through the
screens and select menu items. Press RETURN to exit
the current menu.
Switch on the receiver and your TV.
1
2
Automatically setting up for surround sound
(MCACC)
Switch the TV input to the input that connects this
receiver to the TV through the corresponding
composite cable.
•
Press HOME MENU at any time to exit the Home
Menu. If you cancel the Auto MCACC setup at any
time, the receiver automatically exits and no settings
will be made.
The Auto Multi-Channel Acoustic Calibration (MCACC) setup
measures the acoustic characteristics of your listening area,
taking into account ambient noise, speaker size and distance,
and tests for both channel delay and channel level. After you
have set up the microphone provided with your system, the
receiver uses the information from a series of test tones to
optimize the speaker settings and equalization for your
particular room.
Connect the microphone to the MCACC SETUP MIC jack
on the front panel.
Make sure there are no obstacles between the speakers
and the microphone.
3
•
The screensaver automatically starts after three
minutes of inactivity.
Select ‘Auto MCACC’ from the Home Menu, then press
ENTER
.
AV RECEIVER VSX-522
Home Menu
1.Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
5.Auto Power Down
6.FL Demo Mode
7.HDMI Setup
CAUTION
HDMI
iPod iPhone
•
•
The test tones used in the Auto MCACC setup are output at
high volume.
Important
PRESET
ENTER
Return
The OSD will not appear if you have connected using the
HDMI output to your TV. Use composite connections for
Auto MCACC setup.
SOUND
RETRIEVER
MASTER
VOLUME
•
Mic In! blinks when the microphone is not connected
to MCACC SETUP MIC jack.
•
•
•
The Auto MCACC setup will overwrite any existing speaker
settings you’ve made.
Before using the Auto MCACC setup, the iPod/USB input
should not be selected as an input source.
If you connected either the surround back speaker or the
front height speaker, make sure that the Pre Out setting is
correctly set before performing the Auto MCACC setup (see
page 33). (Here is an explanation using the OSD screen for
a surround back speaker connection.)
Try to be as quiet as possible after pressing ENTER. The
system outputs a series of test tones to establish the
ambient noise level.
MCACC
SETUP MIC
iPod iPhone
USB
Follow the instructions on-screen.
6
•
•
Make sure the microphone is connected.
Make sure the subwoofer is on and the volume is
turned up.
Microphone
•
When using surround back or front height speakers,
turn on the power to the amplifier to which the
surround back or front height speakers are connected,
and adjust the sound level to the desired level.
Tripod
•
See below for notes regarding background noise and
other possible interference.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Setup
3
Wait for the test tones to finish.
Make sure ‘OK’ is selected, then press ENTER.
Other problems when using the Auto MCACC
setup
7
9
A progress report is displayed on-screen while the
receiver outputs test tones to determine the speakers
present in your setup. Try to be as quiet as possible while
it’s doing this.
If the screen in step 8 is left untouched for 10 seconds
and ENTER is not pressed in step 9, the Auto MCACC
setup will start automatically as shown.
If the room environment is not optimal for the Auto MCACC
setup (too much background noise, echo off the walls,
obstacles blocking the speakers from the microphone) the
final settings may be incorrect. Check for household
appliances (air conditioner, fridge, fan, etc.), that may be
affecting the environment and switch them off if necessary. If
there are any instructions showing in the front panel display,
please follow them.
1.Auto MCACC
Now Analyzing
1.Auto MCACC
Now Analyzing
Surround Analyzing
Speaker System
Speaker Distance
Channel Level
Environment Check
Ambient Noise
Speaker YES/NO
Acoustic Cal EQ
Return
•
Some older TVs may interfere with the operation of the
microphone. If this seems to be happening, switch off the
TV when doing the Auto MCACC setup.
Return
A progress report is displayed on-screen while the
receiver outputs more test tones to determine the
optimum receiver settings for channel level, speaker
distance, and Acoustic Calibration EQ.
Again, try to be as quiet as possible while this is
happening. It may take 1 to 3 minutes.
•
For correct speaker settings, do not adjust the volume
during the test tones.
Confirm the speaker configuration.
The configuration shown on-screen should reflect the
actual speakers you have.
8
The Auto MCACC setup has finished! You return to the
10 Home Menu.
1.Auto MCACC
Check!
The settings made in the Auto MCACC setup should give
Front
Center
Surr
[
[
[
YES
YES
YES
]
]
]
you excellent surround sound from your system, but it is
also possible to adjust these settings manually using the
Home Menu (starting on page 30).
Surr. Back [YESx2]
Subwoofer
[
YES
]
OK
Return
Note
10:Next
•
•
Depending on the characteristics of your room, sometimes
identical speakers with cone sizes of around 12 cm
(5 inches) will end up with different size settings. You can
correct the setting manually using the Speaker Setting on
page 30.
The subwoofer distance setting may be farther than the
actual distance from the listening position. This setting
should be accurate (taking delay and room characteristics
into account) and generally does not need to be changed.
•
With error messages (such as Too much ambient
noise) select RETRY after checking for ambient noise
(see Other problems when using the Auto MCACC
setup below).
If the speaker configuration displayed isn’t correct, use
/ to select the speaker and / to change the
setting. When you’re finished, go to the next step.
If you see an error message (ERR) in the right side
column, there may be a problem with the speaker
connection. If selecting RETRY doesn’t fix the problem,
turn off the power and check the speaker connections.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
Basic playback
4
Press AUTO/DIRECT to select ‘AUTO SURROUND’ and
start playback of the source.
Selecting the audio input signal
Playing a source
Here are the basic instructions for playing a source (such as
a DVD disc) with your home theater system.
4
The audio input signal can be selected for each input source.
Once it is set, the audio input that was selected will be applied
whenever you select the input source using the input function
buttons.
If you’re playing a Dolby Digital or DTS surround sound
DVD disc, with a digital audio connection, you should
hear surround sound. If you’re playing a stereo source or
if the connection is an analog audio connection, you will
only hear sound from the front left/right speakers in the
default listening mode.
It is possible to check on the front panel display whether
or not surround sound playback is being performed
properly.
When using a surround back speaker, 2D+PLIIx is
displayed when playing Dolby Digital 5.1-channel signals,
and DTS+NEO:6 is displayed when playing DTS 5.1-
channel signals.
When not using a surround back speaker, 2D is
displayed when playing Dolby Digital signals.
Press SIGNAL SEL to select the audio input signal
corresponding to the source component.
Each press cycles through the following:
•
H – Selects an HDMI signal. H can be selected for BD,
DVD, SAT/CBL or GAME input. For other inputs, H
cannot be selected.
Switch on your system components and receiver.
Start by switching on the playback component (for
example a DVD player), your TV and subwoofer (if you
If the display does not correspond to the input signal and
listening mode, check the connections and settings.
1
-
When the HDMI option in Setting the Audio options
on page 28 is set to THRU, the sound will be heard
through your TV, not from this receiver.
Note
have one), then the receiver (press
RECEIVER).
•
•
You may need to check the digital audio output settings on
your DVD player or digital satellite receiver. It should be set
to output Dolby Digital, DTS and 88.2 kHz/96 kHz PCM (2
channel) audio, and if there is an MPEG audio option, set
this to convert the MPEG audio to PCM.
Depending on your DVD player or source discs, you may
only get digital 2 channel stereo and analog sound. In this
case, the receiver must be set to a multichannel listening
mode if you want multichannel surround sound.
•
Make sure the setup microphone is disconnected.
•
•
A – Selects the analog inputs.
Switch the TV input to the input that connects this
receiver.
For example, if you connected this receiver to the VIDEO
jacks on your TV, make sure that the VIDEO input is now
selected.
C1/O1 – Selects the digital input. The coaxial 1 input is
selected for C1, and the optical 1 audio input is
selected for O1.
2
3
When H (HDMI) or C1/O1 (digital) is selected and the
selected audio input is not provided, A (analog) is
automatically selected.
Press input function buttons to select the input function
you want to play.
Note
Use VOLUME +/– to adjust the volume level.
Turn down the volume of your TV so that all sound is
coming from the speakers connected to this receiver.
•
The input of the receiver will switch over, and you will
be able to operate other components using the remote
•
•
BD and GAME inputs are fixed to H (HDMI). It cannot be
changed.
5
control. To operate the receiver, first press
RECEIVER
For the TV input, only A (analog) or C1/O1 (digital) can be
selected. However, if the ARC at HDMI Setup is set to ON,
the input is fixed to H (HDMI) and cannot be changed.
When set to H (HDMI) or C1/O1 (digital), 2 lights when a
Dolby Digital signal is input, and DTS lights when a DTS
signal is input.
on the remote control, then press the appropriate
button to operate.
•
The input source can also be selected by using INPUT
•
•
SELECT
buttons on the remote control, or by
using the front panel INPUT SELECTOR dial. In this
case, the remote control won’t switch operational
modes.
When the H (HDMI) is selected, the A and DIGITAL
indicators are off (see page 7).
If you selected the proper input source and there is still
no sound, select the audio input signal for playback (see
Selecting the audio input signal below).
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
4
•
When digital input (optical or coaxial) is selected, this
receiver can only play back Dolby Digital, PCM (32 kHz to
96 kHz) and DTS (including DTS 96 kHz/24 bit) digital signal
formats. The compatible signals via the HDMI terminals
are: Dolby Digital, DTS, SACD (DSD 2 ch only), PCM
(32 kHz to 192 kHz sampling frequencies), Dolby TrueHD,
Dolby Digital Plus, DTS-EXPRESS, DTS-HD Master Audio
and DVD Audio (including 192 kHz). With other digital
signal formats, set to A (analog).
You may get digital noise when a LD or CD player
compatible with DTS is playing an analog signal. To prevent
noise, make the proper digital connections (page 13) and
set the signal input to C1/O1 (digital).
Tip
•
In order to enjoy the picture and/or sound from devices connected to each terminal, select the input by doing the following.
Audio
ASSIGNABLE
OUT
IN
IN
HDMI
DVD
CD
SAT/CBL
TV
SIGNAL SEL
1
TV
1
IN
IN
ASSIGNABLE
(
)
(
)
CD
DVD
SAT/CBL
GAME
BD
BD
C1
•
•
OPTICAL
COAXIAL
PRE OUT
SUB WOOFER
Video/Audio (HDMI)
DVD SAT/CBL GAME
Audio
Some DVD players don’t output DTS signals. For more
details, refer to the instruction manual supplied with your
DVD player.
TV
1.
(TV input)
SURR BACK/
FRONT HEIGHT
)
(L
Other than TV input
Single
2.
FRONT
ANTENNA
PRE OUT
R
L
SIGNAL SEL
R
L
AM LOOP
O1
Video
IN
TUNER
SAT/CBL DVD
OR SAT/CBL DVD
R
T
IN
IN
FM UNBAL
75
(
1
)
1
DVD SAT/CBL
ANALOG IN CD
ASSIGNABLE
AUDIO
VIDEO
Class 2 Wiring
SPE
ANALOG IN1 audio input terminal is
assigned to CD under factory settings.
If you want to change this to TV input,
please change the settings in the
Input Assign menu (page 32).
Audio
CD
Audio
DVD SAT/CBL
TV
SIGNAL SEL
SIGNAL SEL
A
A
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
4
Use TOP MENU to display iPod Top menu.
When the display shows Top Menu you’re ready to play
music from the iPod.
Basic playback controls
This receiver’s remote control buttons can be used for basic
playback of files stored on an iPod.
Playing an iPod
This receiver has a dedicated iPod terminal that will allow you
to control playback of audio content from your iPod using the
controls of this receiver.
4
•
If after pressing iPod/USB the display shows NO
DEVICE, try switching off the receiver and
reconnecting the iPod to the receiver.
•
Press iPod/USB to switch the remote control to the iPod/
USB operation mode.
Important
•
The controls of your iPod will be inoperable when
connected to this receiver.
•
Pioneer cannot under any circumstances accept
responsibility for any direct or indirect loss arising from any
inconvenience or loss of recorded material resulting from
the iPod failure.
Playing back files stored on an iPod
To navigate songs on your iPod, you can take advantage of the
OSD of your TV connected to this receiver. You can also
control all operations for music in the front panel display of
this receiver.
Note
•
This receiver is compatible with the audio of the iPod touch
(1st/2nd/3rd/4th generation), iPod classic, iPod nano (3rd/
4th/5th/6th generation), iPhone 3G, iPhone 3GS, iPhone 4
and iPhone 4S (iPod shuffle not supported). However, that
some of the functions may be restricted for some models.
This receiver has been developed and tested for the
software version of iPod/iPhone indicated on the website of
Pioneer (http://pioneer.jp/homeav/support/ios/na/).
Installing software versions other than indicated on the
website of Pioneer to your iPod/iPhone may result in
incompatibility with this receiver.
iPod and iPhone are licensed for reproduction of non-
copyrighted materials or materials the user is legally
permitted to reproduce.
•
Note that non-roman characters in the title are displayed as
‘*’.
•
During Audiobook playback, press / to switch the
playback speed: Faster Normal Slower
•
This feature is not available for photos or video clips on your
iPod.
•
•
•
•
Switches between the iPod controls and the
receiver controls
This allows you to switch between performing iPod operations
Finding what you want to play
When your iPod is connected to this receiver, you can browse
songs stored on your iPod by playlist, artist, album name,
song name, genre or composer, similar to using your iPod
directly.
via the receiver remote control or on the iPod itself.
Press iPod CTRL to switch to the iPod controls.
Use / to select a category, then press ENTER to
•
Press iPod CTRL again to switch back to the receiver
controls when you’re done.
1
browse that category.
Features such as the equalizer cannot be controlled using
this receiver, and we recommend switching the equalizer
off before connecting.
•
To return to the previous level any time, press RETURN.
Use / to browse the selected category (e.g.,
2
3
albums).
Switch on the receiver and your TV.
See Connecting an iPod on page 17.
1
2
•
Use / to move to previous/next levels.
Continue browsing until you arrive at what you want to
Switch the TV input so that it connects to the receiver.
play, then press
to start playback.
•
Switch the TV input to the input that connects this
receiver to the TV through the corresponding
composite cable.
Tip
•
•
If you’re in the song category, you can also press ENTER to
start playback.
You can play all of the songs in a particular category by
selecting the All item at the top of each category list. For
example, you can play all the songs by a particular artist.
Press iPod/USB to switch the receiver to the iPod/USB
input.
The front panel display shows Loading while the receiver
verifies the connection and retrieves data from the iPod.
3
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
4
Press iPod/USB on the remote control to switch the
receiver to the iPod/USB input.
Loading appears in the OSD as this receiver starts
recognizing the USB device connected. After the
recognition, a playback screen appears in the OSD and
playback starts automatically.
Compressed audio compatibility
Playing a USB device
It is possible to listen to two-channel audio using the USB
interface on the front of this receiver.
3
Note that although most standard bit/sampling rate
combinations for compressed audio are compatible, some
irregularly encoded files may not play back. The list below
shows compatible formats for compressed audio files:
Important
•
MP3 (MPEG-1/2/2.5 Audio Layer 3) – Sampling rates:
32 kHz/44.1 kHz/48 kHz; Bit rates: 32 kbps to 320 kbps
(128 kbps or higher recommended); File extension: .mp3
WMA (Windows Media Audio) – Sampling rates: 32 kHz/
44.1 kHz/48 kHz; Bit rates: 48 kbps to 192 kbps (128 kbps or
higher recommended); File extension: .wma; WMA9 Pro
and WMA lossless encoding: No
•
Pioneer cannot guarantee compatibility (operation and/or
bus power) with all USB mass storage devices and
assumes no responsibility for any loss of data that may
occur when connected to this receiver.
Basic playback controls
This receiver’s remote control buttons can be used for basic
playback of files stored on USB devices.
Press iPod/USB to switch the remote control to the iPod/
•
Note
•
•
•
This includes playback of WMA/MP3/MPEG-4 AAC files
(except files with copy-protection or restricted playback).
Compatible USB devices include external magnetic hard
drives, portable flash memory (particularly keydrives) and
digital audio players (MP3 players) of format FAT16/32. It is
not possible to connect this receiver to a personal
computer for USB playback.
USB operation mode.
•
AAC (MPEG-4 Advanced Audio Coding) – Sampling rates:
32 kHz/44.1 kHz/48 kHz; Bit rates: 16 kbps to 320 kbps
(128 kbps or higher recommended); File extension: .m4a;
Apple lossless encoding: No
Other compatibility information
•
VBR (variable bit rate) MP3/WMA/MPEG-4 AAC playback:
Yes (Note that in some cases playback time will not be
displayed correctly.)
•
•
•
With large amounts of data, it may take longer for the
receiver to read the contents of a USB device.
If the file selected cannot be played back, this receiver
automatically skips to the next file playable.
When the file currently being played back has no title
assigned to it, the file name is displayed in the OSD instead;
when neither the album name nor the artist name is
present, the row is displayed as a blank space.
•
DRM (Digital Rights Management) protection compatible:
Yes (DRM-protected audio files will not play in this
receiver.)
Important
About MPEG-4 AAC
If a USB Error message lights in the display, try following the
points below:
Switch the receiver off, then on again.
Reconnect the USB device with the receiver switched off.
Select another input source (like BD), then switch back to
iPod/USB.
Use a dedicated AC adapter (supplied with the device) for
USB power.
For more information on error messages, see USB messages
on page 36.
If this doesn’t remedy the problem, it is likely your USB device
is incompatible.
Advanced Audio Coding (AAC) is at the core of the MPEG-4
AAC standard, which incorporates MPEG-2 AAC, forming the
basis of the MPEG-4 audio compression technology. The file
format and extension used depend on the application used to
encode the AAC file. This receiver plays back AAC files
encoded by iTunes® bearing the extension ‘.m4a’. DRM-
protected files will not play, and files encoded with some
versions of iTunes® may not play.
•
•
Note that non-roman characters in the playlist are
displayed as ‘*’.
Make sure the receiver is in standby when disconnecting
the USB device.
•
•
•
Switch on the receiver and your TV.
See Connecting a USB device on page 17.
•
1
2
Apple and iTunes are trademarks of Apple Inc., registered in the
U.S. and other countries.
Switch the TV input so that it connects to the receiver.
•
Switch the TV input to the input that connects this
receiver to the TV through the corresponding
composite cable.
About WMA
WMA is an acronym for Windows Media Audio and refers to
an audio compression technology developed by Microsoft
Corporation. This receiver plays back WMA files encoded
using Windows Media® Player bearing the extension ‘.wma’.
Note that DRM-protected files will not play, and files encoded
with some versions of Windows Media® Player may not play.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic playback
4
Note
Improving FM sound
Listening to the radio
•
•
If the receiver is left disconnected from the AC power outlet
for over a month, the station memories will be lost and will
have to be reprogrammed.
Stations are stored in stereo. When the station is stored in
the FM MONO mode, it shows as ST when recalled.
If the TUNE or ST indicators don’t light when tuning to an FM
station because the signal is weak, set the receiver to the
mono reception mode.
The following steps show you how to tune in to FM and AM
radio broadcasts using the automatic (search) and manual
(step) tuning functions. Once you are tuned to a station you
can memorize the frequency for recall later—see Saving
station presets below for more on how to do this.
Press BAND to select FM MONO.
This should improve the sound quality and allow you to
enjoy the broadcast.
Listening to station presets
You will need to have some presets stored to do this. See
Saving station presets above if you haven’t done this already.
Saving station presets
If you often listen to a particular radio station, it’s convenient
to have the receiver store the frequency for easy recall
whenever you want to listen to that station. This saves the
effort of manually tuning in each time. This unit can memorize
up to 30 stations.
Press PRESET / to select the station preset you
want.
•
You can also use the number buttons on the remote
control to recall the station preset.
Press TUNER to select the tuner.
Naming preset stations
For easier identification, you can name all of your preset
stations.
1
Use BAND to change the band (FM or AM), if necessary.
Each press switches the band between FM (stereo or
mono) and AM.
2
Choose the station preset you want to name.
See Listening to station presets above for how to do this.
1
Tune to a station.
3
There are three ways to do this:
Press TOOLS twice.
The cursor at the first character position is blinking on
the display.
2
Automatic tuning
To search for stations in the currently selected band,
press and hold TUNE / for about a second. The
receiver will start searching for the next station, stopping
when it has found one. Repeat to search for other
stations.
Manual tuning
To change the frequency one step at a time, press
Input the name you want.
Choose a name up to eight characters long.
3
•
•
•
Use PRESET / to select character position.
Use TUNE / to select characters.
The name is stored when ENTER is pressed.
Tune to a station you want to memorize.
1
TUNE /
.
See Listening to the radio above for more on this.
Tip
High speed tuning
Press and hold TUNE / for high speed tuning.
Release the button at the frequency you want.
Press TOOLS
.
•
•
To erase a station name, follow steps 1 and 2, and press
ENTER while the display is blank. Press TOOLS while the
display is blank, to keep the previous name.
Once you have named a station preset, Press DISP to show
the name. When you want to return to the frequency
display, press DISP several times to show the frequency.
2
3
4
The display shows PRESET, then a blinking MEM and
station preset.
Press PRESET / to select the station preset you
want.
You can also use the number buttons.
Press ENTER
.
The preset number stop blinking and the receiver stores
the station.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
Listening to your system
5
Note
Choosing the listening mode
This receiver offers a variety of listening modes to
•
Stereo surround (matrix) formats are decoded accordingly
using NEO:6 CINEMA or DOLBY PLIIx MOVIE (see
Listening in surround sound below for more on these
decoding formats).
Type of surround
modes
Suitable sources
accommodate playback of various audio formats. Choose one
according to your speaker environment or the source.
While listening to a source, press the listening mode
button repeatedly to select a listening mode you want.
ALC/
STANDARD SURR
STAANLDCA/RD
Listening in surround sound
Two channel sources
STEREO ALC
See above.
Movie
–
–
Using this receiver, you can listen to any source in surround
sound. However, the options available will depend on your
speaker setup and the type of source you’re listening to.
a
DOLBY PLIIx MOVIE
No
Yes
DOLBY PLII MOVIE
No
–
•
If the source is Dolby Digital, DTS, or Dolby Surround
encoded, the proper decoding format will automatically be
selected and shows in the display.
b
a
Music
No
DOLBY PLIIx MUSIC
Yes
No
b
–
DOLBY PLII MUSIC
When you select STEREO ALC (Auto Level Control stereo
mode), this unit equalizes playback sound levels if each sound
level varies with the music source recorded in a portable
audio player.
When you select STEREO, you will hear the source through
just the front left and right speakers (and possibly your
subwoofer depending on your speaker settings). Dolby Digital
and DTS multichannel sources are downmixed to stereo.
a
DOLBY PLIIx GAME
DOLBY PLII GAME
Video games
No
Yes
No
No
–
DISPLAY
BAND
TUNER EDIT
TUNE
c
Movie/Music
Movie
Yes
DOLBY PLIIz HEIGHT
AUTO SURROUND
STREAM DIRECT STANDARD SURR
/
ALC/
ADVANCED
SURROUND
SOUND
RETRIEVER
STEREO
d
–
–
–
–
NEO:6 CINEMA
d
Music
NEO:6 MUSIC
DOLBY PRO LOGIC
Old movies
–
–
–
•
•
The listening mode is shown on the display on the front
panel.
The following modes provide basic surround sound for stereo
and multichannel sources.
Explanatory notes
e
No additional effects
No
Straight Decode
Important
f
See above.
–
–
STEREO
The listening modes and many features described in this
section may not be available depending on the current
source, settings and status of the receiver.
No: No connected / Yes: Connected / Two: Two speakers are
connected / –: Whether connected or no
Multichannel sources
STEREO ALC
See above.
Movie
–
–
DOLBY PLIIx MOVIE
Two
Yes
No
No
AUTO SURROUND
/
AUTO/
Auto playback
b
STREAM DIRECT
Music
DOLBY PLIIx MUSIC
DIRECT
DOLBY DIGITAL EX
DTS-ES
Movie/Music
Movie/Music
Movie/Music
Yes
Yes
Yes
No
–
No
No
No
Yes
–
The simplest, most direct listening option is the AUTO
SURROUND feature. With this, the receiver automatically
detects what kind of source you’re playing and selects
multichannel or stereo playback as necessary.
DTS NEO:6
DOLBY PLIIz HEIGHT Movie/Music
•
Press AUTO/DIRECT repeatedly until AUTO SURROUND
shows briefly in the display (it will then show the decoding
or playback format). Check the digital format indicators in
the display to see how the source is being processed.
e
No additional effects
See above.
Straight Decode
f
–
–
STEREO
a. If surround back channel processing (page 27) is switched off,
or the surround back speakers are set to NO, DOLBY PLIIx
becomes DOLBY PLII (5.1 channel sound).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
5
b. You can also adjust the C.WIDTH, DIMEN., and PNRM. effect
(see Setting the Audio options on page 28).
c. You can also adjust the H.GAIN effect (see Setting the Audio
options on page 28).
d. You can also adjust the C.IMG effect (see Setting the Audio
options on page 28).
e. Cannot be selected when the Pre Out is set to Surr. Back (see
F.S.S.ADVANCE
(Front Stage
Surround
Allows you to create natural surround
sound effects using just the front speakers
and the subwoofer.
Use to provide a rich surround sound effect
directed to the center of where the front left
and right speakers sound projection area
converges.
Using the Sound Retriever
When audio data is removed during the compression
process, sound quality often suffers from an uneven sound
image. The Sound Retriever feature employs new DSP
technology that helps bring CD quality sound back to
compressed 2-channel audio by restoring sound pressure
and smoothing jagged artifacts left over after compression.
ADVANCE)
The Pre Out Setting on page 33).
Front left
speaker
Front right
speaker
f. • You can choose the STEREO mode by using STEREO button.
• The audio is heard with your surround settings and you can
still use the Midnight, Loudness, Phase Control, Sound
Retriever and Tone functions.
Note
•
In modes that give 6.1 channel sound, the same signal is
heard from both surround back speakers.
Press S.RETRIEVER to switch the S.RTV (Sound
Retriever) ON or OFF.
ADVANCED
SURROUND
PHONES SURR
When listening through headphones, you
can still get the effect of overall surround
Using the Advanced surround
ADV SURR
Note
The Advanced surround feature creates a variety of surround
effects. Try different modes with various soundtracks to see
which you like.
AUTO SURROUND
/
•
The Sound Retriever is only applicable to 2-channel
sources.
AUTO/
STREAM DIRECT
Using Stream Direct
DIRECT
ACTION
Designed for action movies with dynamic
soundtracks.
Use the Stream Direct modes when you want to hear the
truest possible reproduction of a source. All unnecessary
signal processing is bypassed.
Listening with Acoustic Calibration EQ
DRAMA
Designed for movies with lots of dialog.
Suitable for musical sources.
You can listen to sources using the Acoustic Calibration
Equalization set in Automatically setting up for surround
sound (MCACC) on page 18. Refer to these pages for more on
Acoustic Calibration Equalization.
AUTO SURROUND See Auto playback on page 25.
ENT.SHOW
DIRECT
Sources are heard according to the settings
made in the Manual SP Setup (speaker
setting, channel level, speaker distance), as
well as with dual mono settings. You will
hear sources according to the number of
channels in the signal.
Phase Control, Acoustic Calibration EQ,
Sound Delay, Auto Delay, LFE Attenuate
and Center image functions are available.
ADVANCED GAME Suitable for video games.
SPORTS
Suitable for sports programs.
CLASSICAL
ROCK/POP
Gives a large concert hall-type sound
Creates a live concert sound for rock and/or
pop music.
UNPLUGGED
EXT.STEREO
Suitable for acoustic music sources.
Gives multichannel sound to a stereo
source, using all of your speakers
PURE DIRECT
Analog and PCM sources are heard without
any digital processing.
While listening to a source, press Acous.EQ to switch
the EQ (Acoustic Calibration EQ) ON or OFF.
The MCACC indicator on the front panel lights when
Acoustic Calibration EQ is active.
•
You can’t use Acoustic Calibration EQ with Stream
Direct mode and it has no effect with headphones.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
5
Better sound using Phase Control
Using surround back channel processing
Setting the Up Mix function
This receiver’s Phase Control feature uses phase correction
measures to make sure your sound source arrives at the
listening position in phase, preventing unwanted distortion
and/or coloring of the sound.
Phase Control technology provides coherent sound
reproduction through the use of phase matching for an
optimal sound image at your listening position. The default
setting is on and we recommend leaving Phase Control
switched on for all sound sources.
You can have the receiver automatically use 6.1 or 7.1
decoding for 6.1 encoded sources (for example, Dolby Digital
EX or DTS-ES), or you can choose to always use 6.1 or 7.1
decoding (for example, with 5.1 encoded material). With 5.1
encoded sources, a surround back channel will be generated,
but the material may sound better in the 5.1 format for which
it was originally encoded (in which case, you can simply
switch surround back channel processing off).
In a 7.1-channel surround system with surround speakers
placed directly at the sides of the listening position, the
surround sound of 5.1-channel sources is heard from the side.
The Up Mix function mixes the sound of the surround
speakers with the surround back speakers so that the
surround sound is heard from diagonally to the rear as it
should be.
•
Using the Up Mix function is effective when the speakers in
the 7.1-channel surround system are set up as
•
With a 7.1-channel surround system, audio signals that
have undergone matrix decoding processing through
surround back channel processing to which the Up Mix
function is added are output from the surround back
speakers.
recommended in the example on page 10.
•
Depending on the positions of the speakers and the sound
source, in some cases it may not be possible to achieve
good results. In this case, set the setting to OFF.
UP MIX OFF
UP MIX ON
SW
C
SW
C
L
R
L
R
Press PHASE to switch the P.CTL (Phase Control) ON or
OFF.
SL
SR
SL
SR
Note
RECEIVER
Press
, then press SB CH repeatedly to cycle
•
•
•
Phase matching is a very important factor in achieving
proper sound reproduction. If two waveforms are ‘in phase’,
they crest and trough together, resulting in increased
amplitude, clarity and presence of the sound signal. If a
crest of a wave meets a trough, then the sound will be ‘out
of phase’ and an unreliable sound image will be produced.
If your subwoofer has a phase control switch, set it to the
plus (+) sign (or 0°). However, the effect you can actually
feel when Phase Control is set to ON on this receiver
depends on the type of your subwoofer. Set your subwoofer
to maximize the effect. It is also recommended you try
changing the orientation or the place of your subwoofer.
Set the built-in lowpass filter switch of your subwoofer to
OFF. If this cannot be done on your subwoofer, set the
cutoff frequency to a higher value.
SBL
SBR
SBL
SBR
the surround back channel options.
Each press cycles through the options as follows:
Switch the receiver into standby.
1
2
•
SB ON – Matrix decoding processing for generating
the surround back component from the surround
component is turned on.
SB AUTO – Matrix decoding processing for generating
the surround back component from the surround
component is switched automatically. Matrix
decoding processing is only performed when surround
back channel signals are detected in the input signals.
While holding down PRESET
on the front panel, and
hold the STANDBY/ON for about two seconds.
•
UP MIX: OFF appears and the Up Mix function turns off.
If you want to turn this function on, perform steps 1 and
2 again.
•
When set to ON, the
panel lights.
(Up Mix) indicator on the front
•
SB OFF – Matrix decoding processing for generating
the surround back component from the surround
component is turned off.
Note
•
•
•
Set to ON regardless of this setting when playing DTS-HD
signals.
May automatically be set to OFF even when set to ON,
depending on the input signal and listening mode.
If the Standby Through is not set to OFF, you may not be
able to set the Up Mix function.
•
•
If the speaker distance is not properly set, you may not have
a maximized Phase Control effect.
The Phase Control mode cannot be set to ON in the
following cases:
-
When the PURE DIRECT mode is switched on.
-
When the headphones are connected.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
5
Setting/What it does
Option(s)
Setting/What it does
Option(s)
Setting the Audio options
There are a number of additional sound settings you can
make using the AUDIO PARAMETER menu. The defaults, if
not stated, are listed in bold.
e
EQ (Acoustic Calibration EQ)
Switches on/off the effect of Acoustic
Calibration EQ.
ON
DRC (Dynamic Range Control)
AUTO
Adjusts the level of dynamic range for movie
soundtracks optimized for Dolby Digital, DTS,
Dolby Digital Plus, Dolby TrueHD, DTS-HD
and DTS-HD Master Audio (you may need to
use this feature when listening to surround
sound at low volumes).
OFF
MAX
MID
OFF
S.DELAY (Sound Delay)
Some monitors have a slight delay when
showing video, so the soundtrack will be
slightly out of sync with the picture. By adding frames (NTSC)
a bit of delay, you can adjust the sound to
match the presentation of the video.
0.0 to 9.0
(frames)
1 second = 30
Important
•
Note that if a setting doesn’t appear in the AUDIO
PARAMETER menu, it is unavailable due to the current
source, settings and status of the receiver.
LFE ATT (LFE Attenuate)
0 (0 dB)
5 (–5 dB)
Default: 0.0
Some Dolby Digital and DTS audio sources
include ultra-low bass tones. Set the LFE
attenuator as necessary to prevent the ultra-
low bass tones from distorting the sound from
the speakers.
The LFE is not limited when set to 0 dB, which
is the recommended value. When set to –15
dB, the LFE is limited by the respective
degree. When OFF is selected, no sound is
output from the LFE channel.
a
M/L OFF
MIDNIGHT
LOUDNESS
MIDNIGHT/LOUDNESS
10 (–10 dB)
15 (–15 dB)
20 (–20 dB)
** (OFF)
The MIDNIGHT allows you to hear effective
surround sound of movies at low volumes.
The LOUDNESS is used to get good bass and
treble from music sources at low volumes.
b
c
S.RTV (Sound Retriever)
OFF
When audio data is removed during the
compression process, sound quality often
suffers from an uneven sound image. The
Sound Retriever feature employs new DSP
technology that helps bring CD quality sound
back to compressed 2-channel audio by
restoring sound pressure and smoothing
jagged artifacts left over after compression.
ON
f
RECEIVER
button.
0 (0 dB)
Press
, then press AUDIO PARAMETER
SACD G. (SACD Gain)
1
2
Brings out detail in SACDs by maximizing the
dynamic range (during digital processing).
+6 (+6 dB)
Use / to select the setting you want to adjust.
HDMI (HDMI Audio)
AMP
Depending on the current status/mode of the receiver,
certain options may not be able to be selected. Check the
table below for notes on this.
Specifies the routing of the HDMI audio signal
out of this receiver (AMP) or through to a TV
(THRU). When THRU is selected, no sound is
output from this receiver.
THRU
d
CH1 – Channel 1
is heard only
DUAL MONO
Specifies how dual mono encoded Dolby
Digital soundtracks should be played.
Use / to set it as necessary.
See the table below for the options available for each
setting.
3
4
CH2 – Channel 2
is heard only
g
OFF
A.DLY (Auto Delay)
This feature automatically corrects the audio-
to-video delay between components
connected with an HDMI cable. The audio
delay time is set depending on the operational
status of the display connected with an HDMI
cable. The video delay time is automatically
adjusted according to the audio delay time.
ON
CH1 CH2 – Both
channels heard
from front
Press RETURN to confirm and exit the menu.
speakers
F.PCM (Fixed PCM)
OFF
This is useful if you find there is a slight delay
before OFF recognizes the PCM signal on a
CD, for instance.
When ON is selected, noise may be output
during playback of non-PCM sources. Please
select another input signal if this is a problem.
ON
h
0 to 7
Default: 3
C.WIDTH (Center Width)
(Applicable only when using a center speaker)
Spreads the center channel between the front
right and left speakers, making it sound wider
(higher settings) or narrower (lower settings).
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
5
Setting/What it does
Option(s)
–3 to +3
h
DIMEN (Dimension)
Default: 0
Adjusts the surround sound balance from
front to back, making the sound more distant
(minus settings), or more forward (positive
settings).
h
OFF
PNRM. (Panorama)
Extends the front stereo image to include
surround speakers for a ‘wraparound’ effect.
ON
i
0 to 10
Default: 3
(NEO:6 MUSIC),
10 (NEO:6
C.IMG (Center Image)
(Applicable only when using a center speaker)
Adjust the center image to create a wider
stereo effect with vocals. Adjust the effect
from 0 (all center channel sent to front right
and left speakers) to 10 (center channel sent
to the center speaker only).
CINEMA)
H.GAIN (Height Gain)
L (Low)
M (Mid)
H (High)
Adjusts the output from the front height
speaker when listening in DOLBY PLIIz
HEIGHT mode. If set to H, the sound from the
top will be more emphasized.
a. You can change the MIDNIGHT/LOUDNESS options at any
time by using MIDNIGHT button.
b. You can change the Sound Retriever feature at any time by
using S.RETRIEVER button.
c. The default setting when the iPod/USB input is selected is ON.
d. This setting works only with dual mono encoded Dolby Digital
and DTS soundtracks.
e. The initial set AUTO is only available for Dolby TrueHD signals.
Select MAX or MID for signals other than Dolby TrueHD.
f. You shouldn’t have any problems using this with most SACD
discs, but if the sound distorts, it is best to switch the gain
setting back to 0 dB.
g. This feature is only available when the connected display
supports the automatic audio/video synchronizing capability
(‘lip-sync’) for HDMI. If you find the automatically set delay time
unsuitable, set A.DLY to OFF and adjust the delay time
manually. For more details about the lip-sync feature of your
display, contact the manufacturer directly.
h. Only available with 2-channel sources in DOLBY PLII MUSIC
mode.
i. Only when listening to 2-channel sources in NEO:6 CINEMA
and NEO:6 MUSIC mode.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
Home Menu
6
Select the setting you want to adjust.
Using the Home Menu
Manual speaker setup
4
The following section shows you how to make detailed
settings to specify how you’re using the receiver, and also
explains how to fine-tune individual speaker system settings
to your liking.
This receiver allows you to make detailed settings to optimize
the surround sound performance. You only need to make
these settings once (unless you change the placement of your
current speaker system or add new speakers).
These settings are designed to fine-tune your system, but if
you’re satisfied with the settings made in Automatically
setting up for surround sound (MCACC) on page 18, it isn’t
necessary to make all of these settings.
Home Menu
1.Auto MCACC
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
5.Auto Power Down
6.FL Demo Mode
7.HDMI Setup
Important
•
The OSD will not appear if you have connected using the
HDMI output to your TV. Use composite connections for
Home Menu.
Return
•
•
Auto MCACC – This is a quick and effective automatic
surround setup (see Automatically setting up for surround
sound (MCACC) on page 18).
Important
•
•
If headphones are connected to the receiver, disconnect
them.
You can’t use the Home Menu when the iPod/USB input is
•
Depending on the Pre Out Setting, there will be
Manual SP Setup
differences in the speaker items that can be adjusted. The
OSD display for these operating instructions is an example
of when the Pre Out Setting is set to Surr. Back.
-
-
-
-
Speaker Setting – Specify the size and number of
speakers you’ve connected (see below).
X.Over – Specify which frequencies will be sent to the
subwoofer (page 31).
Channel Level – Adjust the overall balance of your
speaker system (page 31).
selected.
Speaker Setting
Use this setting to specify your speaker configuration (size,
number of speakers). It is a good idea to make sure that the
settings made in Automatically setting up for surround sound
(MCACC) on page 18 are correct.
Speaker Distance – Specify the distance of your
speakers from the listening position (page 32).
•
•
•
Input Assign – Specify what you’ve connected to the
ANALOG IN1 audio input (see The Input Assign menu on
page 32).
Pre Out Setting – Specify how to use the PRE OUT SURR
BACK/FRONT HEIGHT outputs (see The Pre Out Setting on
page 33).
Auto Power Down – Sets to automatically turn off the
power when the receiver has not operated for several hours
(see The Auto Power Down menu on page 33).
FL Demo Mode – Sets the demo display on the front panel
display (see The FL Demo Mode menu on page 33).
Select ‘Manual SP Setup’ from the Home Menu.
1
Switch on the receiver and your TV.
Select ‘Speaker Setting’ from the Manual SP Setup
menu.
1
2
2
Press
RECEIVER to switch on.
2a.Speaker Setting
2.Manual SP Setup
Switch the TV input to the input that connects this
receiver to the TV through the corresponding
composite cable.
SMALL
Front
a.Speaker Setting
b.X.Over
c.Channel Level
d.Speaker Distance
Center
[
[
[
SMALL
SMALL
NO
]
]
]
Surr
Surr. Back
Subwoofer:
YES
RECEIVER
Press
, then press HOME MENU.
3
•
•
The Home Menu appears on your TV. Use ///and
ENTER on the remote control to navigate through the
screens and select menu items. Press RETURN to exit
the current menu.
Return
Return
HDMI Setup – Set the audio return channel function and
set the HDMI input signal to Standby Through output or not
during standby (see The HDMI Setup menu on page 33).
Choose the set of speakers that you want to set then
select a speaker size.
Use / to select the size (and number) of each of the
following speakers:
3
•
Press HOME MENU at any time to exit the Home
Menu.
•
Front – Select LARGE if your front speakers reproduce bass
frequencies effectively, or if you didn’t connect a
subwoofer. Select SMALL to send the bass frequencies to
the subwoofer.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Home Menu
6
•
Center – Select LARGE if your center speaker reproduces
Note
Choose the frequency cutoff point.
Frequencies below the cutoff point will be sent to the
subwoofer (or LARGE speakers).
bass frequencies effectively, or select SMALL to send bass
frequencies to the other speakers or subwoofer. If you
didn’t connect a center speaker, choose NO (the center
channel is sent to the other speakers).
Front Height – Select LARGE if your front height speakers
reproduce bass frequencies effectively. Select SMALL to
send bass frequencies to the other speakers or subwoofer.
If you didn’t connect front height speakers choose NO.
3
4
•
If you select SMALL for the front speakers, the subwoofer
will automatically be fixed to YES. Also, the center,
surround, surround back and front height speakers can’t
be set to LARGE if the front speakers are set to SMALL. In
this case, all bass frequencies are sent to the subwoofer.
If the surround speakers are set to NO, the surround back
speakers will automatically be set to NO.
If you have a subwoofer and like lots of bass, it may seem
logical to select LARGE for your front speakers and PLUS
for the subwoofer. This may not, however, yield the best
bass results. Depending on the speaker placement of your
room you may actually experience a decrease in the
amount of bass due to low frequency cancellations. In this
case, try changing the position or direction of speakers. If
you can’t get good results, listen to the bass response with
it set to PLUS and YES or the front speakers set to LARGE
and SMALL alternatively and let your ears judge which
sounds best. If you’re having problems, the easiest option
is to route all the bass sounds to the subwoofer by selecting
SMALL for the front speakers.
When you’re finished, press RETURN
You return to the Manual SP Setup menu.
.
•
•
•
Channel Level
Using the channel level settings, you can adjust the overall
balance of your speaker system, an important factor when
setting up a home theater system.
-
You can only adjust the Front Height setting when Pre
Out Setting is set to Height.
•
•
Surr – Select LARGE if your surround speakers reproduce
bass frequencies effectively. Select SMALL to send bass
frequencies to the other speakers or subwoofer. If you
didn’t connect surround speakers choose NO (the sound of
the surround channels is sent to the other speakers).
Surr. Back – Select the number of surround back speakers
you have (one, two or none). Select LARGE if your surround
back speakers reproduce bass frequencies effectively.
Select SMALL to send bass frequencies to the other
speakers or subwoofer. If you didn’t connect surround back
speakers choose NO.
CAUTION
•
The test tones used in the Channel Level settings are output
at high volume.
Select ‘Manual SP Setup’ from the Home Menu.
1
2
Select ‘Channel Level’ from the Manual SP Setup menu.
2.Manual SP Setup
2c.Channel Level
a.Speaker Setting
b.X.Over
Test Tone
Manual
c.Channel Level
d.Speaker Distance
-
You can only adjust the Surr. Back setting when Pre Out
Setting is set to Surr. Back.
X.Over
Default setting: 100Hz
This setting decides the cutoff between bass sounds playing
back from the speakers selected as LARGE, or the subwoofer,
and bass sounds playing back from those selected as SMALL.
It also decides where the cutoff will be for bass sounds in the
LFE channel.
•
-
If you select one surround back speaker only, make sure
that additional amplifier is hooked up to the PRE OUT L
(Single) terminal.
ENTER:NextReturn
Return
•
Subwoofer – LFE signals and bass frequencies of
channels set to SMALL are output from the subwoofer
when YES is selected (see notes below). Choose the PLUS
setting if you want the subwoofer to output bass sound
continuously or you want deeper bass (the bass
frequencies that would normally come out the front and
center speakers are also routed to the subwoofer). If you did
not connect a subwoofer choose NO (the bass frequencies
are output from other speakers).
Select a setup option.
3
•
Manual – Move the test tone manually from speaker to
speaker and adjust individual channel levels.
•
For more on selecting the speaker sizes, see Speaker Setting
on page 30.
•
Auto – Adjust channel levels as the test tone moves
from speaker to speaker automatically.
Select ‘Manual SP Setup’ from the Home Menu.
1
Select ‘X.Over’ from the Manual SP Setup menu.
2
2.Manual SP Setup
2b.X.Over
Frequency
a.Speaker Setting
b.X.Over
c.Channel Level
d.Speaker Distance
100Hz
When you’re finished, press RETURN
.
4
You return to the Manual SP Setup menu.
Return
Return
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Home Menu
6
Tip
Confirm your selected setup option.
The Input Assign menu
ANALOG IN1 audio input terminal is assigned to CD under
factory settings, but this can be changed to TV input.
4
The test tones will start after you press ENTER. After the
volume increases to the reference level, test tones will be
output.
•
You can change the channel levels at any time by press
, then press CH SELECT and LEV +/– on the
RECEIVER
remote control. You can also press CH SELECT and use /
to select the channel, and then use / to adjust the
channel levels.
Select ‘Input Assign’ from the Home Menu.
1
2c.Channel Level
Test Tone
[
Manual
]
Home Menu
1.Auto MCACC
Please Wait
.
.
.20
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
5.Auto Power Down
6.FL Demo Mode
7.HDMI Setup
Speaker Distance
Caution
For good sound depth and separation from your system, you
need to specify the distance of your speakers from the
listening position. The receiver can then add the proper delay
needed for effective surround sound.
Loud test tones
will be output.
Return
Return
•
For the assignment of the digital signal inputs, see
Selecting the audio input signal on page 20.
Adjust the level of each channel using /
.
5
If you selected Manual, use /to switch speakers. The
Auto setup will output test tones in the order shown on-
screen:
Select ‘Analog Input’ from the Input Assign menu.
2
Select ‘Manual SP Setup’ from the Home Menu.
3a.Analog Input
Analog
3.Input Assign
a.Analog Input
1
2
CD
Select ‘Speaker Distance’ from the Manual SP Setup
menu.
2c.Channel Level
0dB
Front
L
Center
[
[
[
[
[
[
[
0dB]
0dB]
0dB]
–––
–––
0dB]
0dB]
2d.Speaker Distance
2.Manual SP Setup
Front
Surround
Surr. Back
Surr. Back
Surround
Subwoofer
R
R
10.0 ft
10.0 ft
10.0 tt
10.0 ft
Front
L
a.Speaker Setting
b.X.Over
c.Channel Level
d.Speaker Distance
R
L
]
]
Center
[
[
[
[
[
[
[
]
]
]
]
]
]
]
Return
Return
Front
Surround
Surr. Back
Surr. Back
Surround
Subwoofer
R
L
R
R
L
––––
––––
10.0 ft
Return
Select the desired input option for the ANALOG IN1
audio input terminal.
L
3
4
10.0 ft
Adjust the level of each speaker as the test tone is
emitted.
Return
Return
When you’re finished, press RETURN
.
Note
You return to the Input Assign menu.
Adjust the distance of each speaker using /
.
3
4
•
If you are using a Sound Pressure Level (SPL) meter, take
the readings from your main listening position and adjust
the level of each speaker to 75 dB SPL (C-weighting/slow
reading).
The subwoofer test tone is output at low volumes. You may
need to adjust the level after testing with an actual
soundtrack.
You can adjust the distance of each speaker in 0.1 feet
increments.
When you’re finished, press RETURN
You return to the Manual SP Setup menu.
.
•
When you’re finished, press RETURN
You return to the Manual SP Setup menu.
.
6
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Home Menu
6
Specify the amount of time to allow before the power
is turned off (when there has been no operation).
The Pre Out Setting
The HDMI Setup menu
2
3
Specify either using the surround back speaker or the front
height speaker connection with the PRE OUT SURR BACK/
FRONT HEIGHT outputs. An additional amplifier is required
for the speaker connection.
If your TV supports an audio return channel (ARC) function,
connect your TV and this unit with an HDMI cable and the TV
audio will be inputted into this unit via the HDMI terminal
without the need for an audio cable to be connected.
It is possible to transfer signals from an HDMI connected
player to the TV even when this receiver’s power is on standby.
•
You can select 2, 4 or 6 hours, or OFF (if no automatic
shutoff is desired).
When you’re finished, press RETURN
.
•
Default setting: Surr. Back
You return to the Home Menu.
Select ‘Pre Out Setting’ from the Home Menu.
Important
1
Important
•
If the Standby Through of the HDMI Setup is not set to
OFF, the Auto Power Down setting will automatically be
set to OFF and cannot be changed.
Home Menu
1.Auto MCACC
4.Pre Out Setting
Pre Out Surr. Back
•
Use a High Speed HDMI® Cable when using the ARC
function. The ARC function may not operate properly with
other HDMI cables.
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
5.Auto Power Down
6.FL Demo Mode
7.HDMI Setup
Select ‘HDMI Setup’ from the Home Menu.
The FL Demo Mode menu
Set whether or not various demos are to be shown on the front
panel display.
1
Return
Home Menu
1.Auto MCACC
7.HDMI Setup
Return
ARC
Standby Through
OFF
OFF
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
5.Auto Power Down
6.FL Demo Mode
7.HDMI Setup
[
]
Select ‘FL Demo Mode’ from the Home Menu.
Select which speaker to connect to the PRE OUT SURR
BACK/FRONT HEIGHT outputs using /
1
2
3
.
Home Menu
1.Auto MCACC
2.Manual SP Setup
3.Input Assign
6.FL Demo Mode
FL Demo
•
Surr. Back – Connect the surround back speaker.
ON
•
Height – Connect the front height speaker.
Return
Return
4.Pre Out Setting
5.Auto Power Down
6.FL Demo Mode
7.HDMI Setup
When you’re finished, press RETURN
You return to the Home Menu.
.
Choose the ‘ARC’ setting you want.
2
3
When a TV supporting the HDMI Audio Return Channel
function is connected to the receiver, the sound of the TV
can be input via the HDMI terminal.
Return
Return
The Auto Power Down menu
Set to automatically turn off the receiver after a specified time
has passed (when the power has been on with no operation
for several hours).
Choose ON or OFF for the demo display.
•
•
ON – The TV’s sound is input via the HDMI terminal.
OFF – The TV’s sound is input from the audio input
terminals other than HDMI inputs.
2
When you’re finished, press RETURN
.
3
You return to the Home Menu.
•
Default setting: OFF
Choose the ‘Standby Through’ setting you want.
When the receiver is in standby, the HDMI input signal
selected here will be output to the TV by HDMI.
Select ‘Auto Power Down’ from the Home Menu.
1
Home Menu
1.Auto MCACC
5.Auto Power Down
OFF
•
•
•
LAST – The HDMI input signal selected previously will
be output.
BD, DVD, SAT/CBL, GAME – The HDMI input signal
selected here will be output.
2.Manual SP Setup
3.Input Assign
4.Pre Out Setting
5.Auto Power Down
6.FL Demo Mode
7.HDMI Setup
OFF – Signal will not be output during standby.
Return
Return
-
If the Standby Through setting is not set to OFF, the
power consumption during standby will increase.
The Auto Power Down setting will also be
automatically set to OFF.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Home Menu
6
When you're finished, press RETURN
You return to the Home Menu.
.
4
Before starting ARC operation
When starting ARC operation, put the TV and this unit in
STANDBY mode after connecting this unit with the TV. Next,
turn ON the power of this unit and then the TV, in this order.
In order to start ARC operation, after connecting this unit to a
TV with an HDMI cable, you will need to switch the input on
the TV to the input mode required to connect to this unit.
Then, you can select a TV program.
Important
•
•
The ARC function may not operate even if the above
conditions are met. If this is the case, listen to the TV audio
after connecting this unit and the TV with an audio cable.
The CEC (Consumer Electronic Control) function may
activate when the ARC function is turned ON, causing
power to turn ON and OFF and the input to switch from one
to another. Since this unit does not guarantee
synchronized operation based on the CEC function, we
recommend that you turn OFF the HDMI CONTROL setting
on the connected player. This unit may not operate properly
if the HDMI CONTROL on the player is ON. Refer to the
relevant device's instruction manual for details. If this does
not work, turn OFF the ARC function.
If this is the case, listen to the TV audio after connecting
this unit and the TV with an audio cable.
In addition, this unit does not guarantee synchronized
operation that allows the TV remote control to operate the
volume (including mute). Use this unit to operate the
volume (including mute).
•
•
Turn OFF the power and remove the power cord from the
wall socket when connecting other devices or making
connection changes to this unit. After all connections are
completed, insert the power cord into the wall socket.
If the power cord is connected when the ARC function is
ON, the HDMI will take 2 to 10 seconds to initialize. This
unit cannot be operated during the initialization. During
initialization, the HDMI indicator on the display will blink.
Turn ON the unit after blinking stops.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
Additional information
7
Lower the volume level.
Make sure the speaker distance setting is correct for all
speakers (see Speaker Distance on page 32).
Troubleshooting
TEMP shows in the display and the volume level drops.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (page 2).
Lower the volume level.
No sound is output when an input function is selected.
Use VOLUME +/– to turn up the volume.
Press MUTE on the remote control to turn muting off.
Set the SIGNAL SEL to H (HDMI), C1/O1 (digital) or A (analog)
according to the type of connections made (page 20).
Make sure the component is connected correctly (see
Connecting your equipment on page 10).
Check the audio output settings of the source component.
Refer to the instruction manual supplied with the source
component.
No image is output when an input function is selected.
Make sure the component is connected correctly (see
Connecting your equipment on page 10).
Use the same type of video cables for the source component
and TV to connect to this receiver (see About video outputs
connection on page 13).
Considerable noise in radio broadcasts.
Connect the antenna (page 16) and adjust the position for best
reception.
Route any loose cables away from the antenna terminals and
wires.
Fully extend the FM wire antenna, position for best reception,
and secure to a wall (or connect an outdoor FM antenna).
Connect an additional internal or external AM antenna
(page 16).
Turn off equipment causing interference or move it away from
the receiver (or move antennas farther away from equipment
causing noise).
Broadcast stations cannot be selected automatically.
Connect an outdoor antenna (page 16).
Noise during playback of a cassette deck.
Move the cassette deck away from your receiver, until the noise
disappears.
No sound is output or a noise is output when software
with DTS is played back.
Make sure the player’s settings are correct and/or the DTS
signal out is on. Refer to the instruction manual supplied with
the DVD player.
There seems to be a time lag between the speakers and
the output of the subwoofer.
See Automatically setting up for surround sound (MCACC) on
page 18 to set up your system again using MCACC (this will
automatically compensate for a delay in the subwoofer output).
After using the Auto MCACC setup, the speaker size
setting (LARGE or SMALL) is incorrect.
Incorrect operations are often mistaken for trouble and
malfunctions. If you think that there is something wrong with
this component, check the points below. Take a look at the
other components and electrical appliances being used,
because sometimes the problem may lie there. If the trouble
isn’t sorted out even after going through the checks below,
ask your nearest Pioneer authorized independent service
company to carry out repair work.
•
If the unit does not operate normally due to external effects
such as static electricity disconnect the power plug from
the outlet and insert again to return to normal operating
conditions.
General
The power does not turn on.
Disconnect the power plug from the outlet, and insert again.
Make sure there are no loose strands of speaker wire touching
the rear panel. This could cause the receiver to shut off
automatically.
The video input selected on the TV monitor is incorrect. Refer
to the instruction manual supplied with the TV.
No sound from subwoofer.
The receiver suddenly switches off.
When the Auto Power Down function is working, the power will
automatically turn off if the receiver has not operated for
several hours. Check the setting for the Auto Power Down
function (see The Auto Power Down menu on page 33).
After about a minute (you won’t be able to switch the unit on
during this time), switch the receiver back on. If the message
persists, call a Pioneer authorized independent service
company.
Power automatically turns ON/OFF and the input switches
from one to another. (When the ARC function is ON)
The CEC (Consumer Electronic Control) function may activate
when the ARC function is turned ON, causing power to turn
ON and OFF and the input to switch from one to another. Since
this unit does not guarantee synchronized operation based on
the CEC function, turn OFF the HDMI CONTROL setting on the
connected player. Refer to the relevant device’s instruction
manual for details.
Make sure the subwoofer is switched on.
If the subwoofer has a volume knob, make sure it’s turned up.
The Dolby Digital or DTS source you are listening to may not
have an LFE channel.
Switch the subwoofer setting in Speaker Setting on page 30 to
YES or PLUS.
Switch the LFE ATT (LFE Attenuate) on page 28 to LFEATT 0 or
LFEATT 5.
No sound from surround or center speakers.
Connect the speakers properly (page 11).
Refer to Speaker Setting on page 30 to check the speaker
settings.
Refer to Channel Level on page 31 to check the speaker levels.
The Phase Control feature doesn’t seem to have an
audible effect.
If applicable, check that the lowpass filter switch on your
subwoofer is off, or the lowpass cutoff is set to the highest
frequency setting. If there is a PHASE setting on your
subwoofer, set it to 0º (or depending on the subwoofer, the
setting where you think it has the best overall effect on the
sound).
Low-frequency noise could have been caused by an air
conditioner or motor. Switch off all appliances in the room and
rerun the Auto MCACC setup.
Can’t operate the remote control.
Replace the batteries (page 9).
Operate within 7 m (23 ft.), 30º of the remote sensor (page 9).
Remove the obstacle or operate from another position.
Avoid exposing the remote sensor on the front panel to direct
light.
If this does not work, turn OFF the ARC function. If this is the
case, listen to the TV audio after connecting this unit and the
TV with an audio cable.
OVERHEAT shows in the display and the power turns off.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation (page 2).
The display is dark or off.
Press DIMMER on the remote control repeatedly to return to
the default.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
7
The front panel display switches over for no apparent
reason to various different displays.
This happens because the demo display is in operation. To turn
off the demo display, press any button to go back to the
original display, or set the FL Demo Mode to OFF (see The FL
Demo Mode menu on page 33).
The receiver doesn’t recognize iPod touch/iPhone.
Try the following.
1. Simultaneously keep pressing the sleep button and home
button on the iPod touch or iPhone for over 10 seconds to
restart.
No sound, or sound suddenly ceases.
Check that the HDMI setting is set to AMP (page 28).
If the component is a DVI device, use a separate connection for
the audio.
HDMI format digital audio transmissions require a longer time
to be recognized. Due to this, interruption in the audio may
occur when switching between audio formats or beginning
playback.
Turning on/off the device connected to this unit’s HDMI OUT
terminal during playback, or disconnecting/connecting the
HDMI cable during playback, may cause noise or interrupted
audio.
iPod messages
‘iPod/USB Error 1 (I/U ERR1)’,
‘iPod/USB Error 3 (I/U ERR3)’
Switch off the receiver and reconnect the iPod to the receiver. If
this doesn’t seem to work, try resetting your iPod.
‘iPod/USB Error 2 (I/U ERR2)’
Switch off the receiver and reconnect the iPod to the receiver. If
this doesn’t seem to work, try resetting your iPod.
An iPod not supported by this receiver is connected. Connect
the iPod supported by this receiver (page 22).
2. Turn on the receiver.
3. Connect the iPod touch/iPhone to the receiver.
‘No Track’
When there are no tracks in the category selected on the iPod.
Select a different category.
Important information regarding the HDMI
connection
There are cases where you may not be able to route HDMI
signals through this receiver (this depends on the HDMI
equipped component you are connecting-check with the
manufacturer for HDMI compatibility information).
If you aren’t receiving HDMI signals properly through this
receiver (from your component), please try the following
configuration when connecting up.
HDMI
No picture or sound.
If the problem still persists when connecting your HDMI
component directly to your monitor, please consult the
component or monitor manual or contact the manufacturer for
support.
USB messages
‘iPod/USB Error 1 (I/U ERR1)’
There is a problem with the signal path from the USB to the
receiver. Switch off the receiver and reconnect the USB to the
receiver.
‘iPod/USB Error 3 (I/U ERR3)’
When there is no response from the USB. Switch off the
receiver and reconnect the USB to the receiver.
No picture.
Video signals that are input from the analog video terminal will
not output from the HDMI terminal. Signals that are input from
the HDMI terminal will not output from the analog video
terminal. Be consistent with the type of cable between input
and output.
Depending in the output settings of the source component, it
may be outputting a video format that can’t be displayed.
Change the output settings of the source, or connect using the
composite video jacks.
This receiver is HDCP-compatible. Check that the components
you are connecting are also HDCP-compatible. If they are not,
please connect them using the composite video jacks.
Depending on the connected source component, it’s possible
that it will not work with this receiver (even if it is HDCP-
compatible). In this case, connect using the composite video
jacks between source and receiver.
Configuration
‘iPod/USB Error 4 (I/U ERR4)’
Connect your HDMI-equipped component directly to the
display using an HDMI cable. Then use the most convenient
connection (digital is recommended) for sending audio to the
receiver. See the operating instructions for more on audio
connections. Set the display volume to minimum when using
this configuration.
The power requirements of the USB device are too high for this
receiver. Switch off the receiver and reconnect the USB to the
receiver.
Note
•
Depending on the component, audio output may be limited
to the number of channels available from the connected
display unit (for example audio output is reduced to 2
channels for a monitor with stereo audio limitations).
•
•
If you want to switch the input source, you’ll have to switch
functions on both the receiver and your display unit.
Since the sound is muted on the display when using the
HDMI connection, you must adjust the volume on the
display every time you switch input sources.
If video images do not appear on your TV, try adjusting the
resolution, Deep Color or other setting for your component.
To output signals in Deep Color, use an HDMI cable (High
®
Speed HDMI Cable) to connect this receiver to a component
or TV with the Deep Color feature.
The OSD screen (Home Menu, etc.) isn’t displayed.
The OSD will not appear if you have connected using the HDMI
output to your TV. Use composite connections when setting up
the system.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
7
•
If the Standby Through is not set to OFF, you may not be
able to initialize the unit.
Digital In/Out Section
About iPod/iPhone
HDMI terminal . . . . . . . . . . . . . . . . . . . . . . . . . .Type A (19-pin)
HDMI output type . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 100 mA
USB (iPod) terminal . . . . USB2.0 Full Speed (Type A) 5 V, 1 A
Cleaning the unit
•
Miscellaneous
Use a polishing cloth or dry cloth to wipe off dust and dirt.
Power Requirements . . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz
Power Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 W
In standby . . . . . . . . . . . . . . . . . . . . . . . . . . 0.4 W (ARC OFF)
Dimensions . . . . . .435 mm (W) x 168 mm (H) x 342.5 mm (D)
•
When the surface is dirty, wipe with a soft cloth dipped in
some neutral cleanser diluted five or six times with water,
and wrung out well, and then wipe again with a dry cloth.
Do not use furniture wax or cleansers.
Never use thinners, benzine, insecticide sprays or other
chemicals on or near this unit, since these will corrode the
surface.
173/16 in. (W) x 65/8 in. (H) x 131/2 in. (D)
•
“Made for iPod” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod or iPhone, respectively, and has been
certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this
device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod or iPhone
may affect wireless performance.
Weight (without package) . . . . . . . . . . . . . . .8.7 kg (19 lb 3 oz)
Furnished Parts
Microphone (for Auto MCACC setup). . . . . . . . . . . . . . . . . . . 1
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Dry cell batteries (AAA size IEC R03) . . . . . . . . . . . . . . . . . . . 2
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
FM wire antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick start guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Brochure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
These operating instructions (CD-ROM)
Specifications
Amplifier section
Continuous average power output of 80 watts* per
channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no
more than 0.08 %** total harmonic distortion.
Apple, iPhone, iPod, iPod shuffle, iPod nano, iPod classic, iPod
touch and iTunes are trademarks of Apple Inc., registered in the
U.S. and other countries.
Front (stereo) . . . . . . . . . . . . . . . . . . . . . . . . . . .80 W + 80 W
Power output (1 kHz, 6 Ω, 1 %). . . . . . . . . . 140 W per channel
Guaranteed speaker impedance . . . . . . . . . . . . . . 6 Ω to 16 Ω
* Measured pursuant to the Federal Trade Commission’s Trade
Regulation rule on Power Output Claims for Amplifiers
** Measured by Audio Spectrum Analyzer
Resetting the main unit
Use this procedure to reset all the receiver’s settings to the
factory default. Use the front panel controls to do this.
Note
•
Specifications and the design are subject to possible
modifications without notice, due to improvements.
Switch the receiver into standby.
Audio Section
Input (Sensitivity/Impedance)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/47 kΩ
Signal-to-Noise Ratio (IHF, short circuited, A network)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 dB
Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 dB
1
While holding down BAND, press and hold
2
STANDBY/ON for about two seconds.
When you see RESET? appear in the display, press
AUTO SURROUND/STREAM DIRECT
OK? shows in the display.
3
.
Press ALC/STANDARD SURR to confirm.
OK appears in the display to indicate that the receiver
has been reset to the factory default settings.
Video Section
4
Signal level
Composite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 Ω)
Important
Tuner Section
Frequency Range (FM) . . . . . . . . . . . . . . 87.5 MHz to 108 MHz
Antenna Input (FM) . . . . . . . . . . . . . . . . . . . . 75 Ω unbalanced
Frequency Range (AM) . . . . . . . . . . . . . . . 530 kHz to 1700 kHz
Antenna (AM). . . . . . . . . . . . . . . . . . . . . . . . . . . . Loop antenna
•
If the ARC function is ON, you may not be able to initialize
the unit. If this happens, turn OFF the ARC function or turn
OFF all the connected device before turning OFF
(STANDBY) the power for this unit, and initialize after the
HDMI indicator goes out.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
7
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a
safe level – a level that lets the sound come through
clearly without annoying blaring or distortion and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time, your hearing
“comfort level” adapts to higher volumes of sound, so
what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by setting
your equipment at a safe level BEFORE your hearing
adapts.
Manufactured under license from Dolby Laboratories. “Dolby”,
“Pro Logic”, “Surround EX”, and the double-D symbol are
trademarks of Dolby Laboratories.
ESTABLISH A SAFE LEVEL:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
• Once you have established a comfortable sound
level, set the dial and leave it there.
Manufactured under license under U.S. Patent Nos: 5,956,674;
5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929;
7,392,195; 7,272,567 & other U.S. and worldwide patents
issued & pending. DTS-HD, the Symbol, & DTS-HD and the
Symbol together are registered trademarks & DTS-HD Master
Audio is a trademark of DTS, Inc. Product includes software.
© DTS, Inc. All Rights Reserved.
BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:
• Do not turn up the volume so high that you can’t
hear what’s around you.
• Use caution or temporarily discontinue use in
potentially hazardous situations.
• Do not use headphones while operating a motorized
vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.
S001a_A1_En
38
Download from Www.Somanuals.com. All Manuals Search And Download.
To register your product, find the nearest authorized service location, to purchase replacement parts,
operating instructions, or accessories, please go to one of following URLs :
Pour enregistrer votre produit, trouver le service après-vente agréé le plus proche et pour acheter des
pièces de rechange, des modes d’emploi ou des accessoires, reportez-vous aux URL suivantes :
In the USA/Aux Etats-Unis
In Canada/Aux Canada
S018_B1_EnFr
© 2012 PIONEER CORPORATION.
All rights reserved.
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270
K002_B3_En
<ARB7467-B>
Download from Www.Somanuals.com. All Manuals Search And Download.
|