XW-SMA1
XW-SMA3
XW-SMA4
Wireless Sound System
Operating Instructions
Indoor Use Only
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
POWER-CORD CAUTION
Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the life or
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
performance of batteries.
D3-4-2-3-3_A1_En
When disposing of used batteries, please
comply with governmental regulations or
environmental public institution’s rules that
apply in your country/area.
service center or your dealer for a replacement.
D3-4-2-3-1_B1_En
S002*_A1_En
Radio wave caution
CAUTION
This unit uses a 2.4 GHz radio wave frequency, which is
a band used by other wireless systems (Microwave
ovens and Cordless phones, etc.). In this event noise
appears in your television image, there is the possibility
this unit (including products supported by this unit) is
causing signal interference with the antenna input
connector of your television, video, satellite tuner, etc.
In this event, increase the distance between the
antenna input connector and this unit (including
products supported by this unit).
• Pioneer is not responsible for any malfunction of the
compatible Pioneer product due to communication
error/malfunctions associated with your network
connection and/or your connected equipment.
Please contact your Internet service provider or
network device manufacturer.
Danger of explosion if battery is incorrectly
replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
D3-4-2-3-2_A1_En
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
“Perchlorate Material －special handling may
apply.
See
(Applicable to California, U.S.A.)”
• A separate contract with/payment to an Internet
service provider is required to use the Internet.
This transmitter must not be co-located or operated
in conjunction with any other antenna or transmitter.
WARNING
Store small parts out of the reach of children and
infants. If accidentally swallowed, contact a doctor
immediately.
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may
not cause interference, and (2) this device must
accept any interference, including interference that
may cause undesired operation of the device.
Store the AC adapter out of the reach of
children and infants.
The AC adapter cord may accidentally wind around the
neck and it may cause suffocation.
WARNING
AC adapter CAUTION
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
• Make sure to grasp the body of the AC adapter when
removing it from the power outlet. If you pull the
power cord, it may become damaged which could
lead to fire and/or electrocution.
• Do not attempt to plug in or remove the AC adapter
with wet hands. This may result in electrocution.
moisture.
D3-4-2-1-3_A1_En
• Do not insert the power cord of AC adapter into a
power outlet where the connection remains loose
despite inserting the prongs all the way into the
outlet. Heat may be generated which could lead to
fire. Consult with the retailer or an electrician
regarding replacement of the power outlet.
Download from Www.Somanuals.com. All Manuals Search And Download.
[For American Users]
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.
RECORD THESE NUMBERS ON YOUR ENCLOSED WARRANTY CARD AND KEEP IN A SAFE PLACE FOR FUTURE
REFERENCE.
D36-AP9-1_A1_En
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_A1_En
FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Product Name: Wireless Sound System
Model Number: XW-SMA1-K, XW-SMA3-K, XW-SMA4-K
Responsible Party Name: PIONEER ELECTRONICS (USA) INC.
SERVICE SUPPORT DIVISION
Address: 1925 E. DOMINGUEZ ST. LONG BEACH, CA 90810-1003, U.S.A.
Phone: 1-800-421-1404
D8-10-4*_C1_En
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a
minimum distance of 20 cm between the radiator and
your body.
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a
safe level – a level that lets the sound come through
clearly without annoying blaring or distortion and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time, your hearing
“comfort level” adapts to higher volumes of sound, so
what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by setting
your equipment at a safe level BEFORE your hearing
adapts.
Information to User
Alterations or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
D8-10-2_A1_En
ESTABLISH A SAFE LEVEL:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
• Once you have established a comfortable sound
level, set the dial and leave it there.
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product may expose you to chemicals listed on
proposition 65 known to the State of California and
other governmental entities to cause cancer and
birth defect or other reproductive harm.
BE SURE TO OBSERVE THE FOLLOWING
GUIDELINES:
• Do not turn up the volume so high that you can’t
hear what’s around you.
Wash hands after handling.
D36-P5_B1_En
• Use caution or temporarily discontinue use in
potentially hazardous situations.
• Do not use headphones while operating a motorized
vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.
S001a_A1_En
Download from Www.Somanuals.com. All Manuals Search And Download.
[For European Users]
Information for users on collection and disposal of old equipment and used batteries
Symbol for
equipment
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products and used batteries,
please take them to applicable collection points in accordance with your national
legislation.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
Symbol examples
for batteries
For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
These symbols are only valid in the European Union.
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer and
ask for the correct method of disposal.
Pb
K058a_A1_En
[For Canadian Users]
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed
and operated with a minimum distance of 20 cm
between the radiator and your body.
This Class B digital apparatus complies with
Canadian ICES-003.
D8-10-1-3_A1_En
[For American Users and Canadian Users]
Operating Environment
Operating environment temperature and humidity:
+5 °C to +25 °C (+41 °F to +77 °F); less than 85 %RH (cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight
(or strong artificial light)
D3-4-2-1-7c*_A1_En
[Except American Users and Canadian Users]
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight
(or strong artificial light)
D3-4-2-1-7c*_A1_En
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Use (Important)
Safety Precautions
DANGER
About the Device
Please follow the instructions noted. Failure to do so may cause the built-in lithium-ion battery to
leak, overheat, ignite, or rupture.
•Do not dispose of the device in fire or expose it to heat.
•Do not attempt to disassemble the battery or alter it in any way.
•Do not throw the device, strike it with a hammer or other object, or drive nails into it.
•Do not use or leave the device in places where it will be exposed to high temperatures, such as near
a stove, inside a closed automobile or in direct sunlight.
•In the event that the built-in lithium-ion battery leaks fluid and the fluid contacts your eyes, do not
rub them, but rinse with copious amounts of clean water and seek immediate medical treatment.
Your eyes may be seriously harmed by exposure to such battery fluid.
•Do not allow the battery to be immersed in fresh or sea water, or become otherwise wet.
•Do not recharge the battery near a fire or in direct sunlight.
•Do not recharge the battery using any method other than as instructed.
The battery used in this device may present a risk of fire, explosion or chemical burn if
mistreated.
•Never disassemble the unit or attempt to remove battery as that could cause leakage of alkaline
solution or other electrolytic substance.
•Always keep the battery out of the reach of infants and small children.
WARNING
About the Device
•Do not use the device if it emits an unusual odor, heats up, changes color or shape, or if any other
abnormalities occur during use, while recharging or while placed in storage.
•If the battery does not recharge completely, even after exceeding the specified time, stop recharging.
Failure to do so could cause the device to heat up, rupture, or ignite.
•Recharge the battery in an environment with a temperature between 5 ºC (41 ºF) and 35 ºC (95 ºF).
Recharging the battery under different temperatures could cause the device to heat up, rupture, or
ignite, and may also deteriorate the performance and the life of the built-in lithium-ion battery.
•Do not place the device in a microwave oven or expose it to high pressure, since the device may
overheat, rupture, or ignite.
•Do not place a leaking rechargeable lithium-ion battery near a source of heat or fire, since the battery
could overheat, rupture, or ignite.
CAUTION
About the Device
•Do not dispose of the device in fire or water, since the rechargeable lithium-ion battery could rupture
or leak battery fluid, resulting in fire or personal injury.
•If fluid leaking from a rechargeable lithium-ion battery contacts your skin or clothes, wash
immediately with copious amounts of clean water. If left unattended, a skin rash could result.
Download from Www.Somanuals.com. All Manuals Search And Download.
About water-resistant (XW-SMA3 only)
CAUTION
Observe the following precautions in regard to the device’s water-resistant.
• Do not place the unit in water.
• Do not expose the unit to a large amount of water.
• Do not splash the unit with water.
• Do not expose to rain.
• Do not pour or place in warm water or water containing soap or detergent.
• Do not use in a humid environment such as a bathroom.
• Do not use near or on the beach.
This could cause rust. If exposed to seawater, thoroughly wipe off the moisture immediately with a dry cloth.
• Ensure that the terminal cover is closed during use.
The rubber packing on the cover make the device water-resistant. Make sure this packing does not get
soiled or damaged.
If the rubber packing does become soiled, wipe it clean with a dry, clean cloth.
• Do not open the terminal cover in humid environments in which the device could get
exposed to water.
• If the device is exposed to a large amount of water or moisture, immediately wipe it down
with a dry cloth.
Only open or close the terminal cover after having completely wiped off any moisture around them, with dry
hands and in an environment where the unit would not get exposed to water again.
• Make sure to install the unit on a flat and stable surface. Do not use the unit upside down
or in a tilted position.
Since water may reach the interior of the unit, install the unit in a proper position.
• Do not turn the unit upside down or hold it tilted when it has been exposed to water or water
droplets.
Since the water might run into the interior parts of the unit, do not tilt the unit if it is wet.
• If the device does get exposed to water, thoroughly dry all of the crevices on the unit’s body
into which water might have reached.
The water might have reached the interior of the device. Do not carry the unit if it is still wet.
• Do not use the remote control, AC adapter when in proximity to water.
Only the device itself is water-resistant.
This unit has been designed with water-resistance equivalent to standards IPX2(*) as defined by the
International Electrotechnical Commission (IEC).
Malfunctions due to water damage caused by improper use are not covered by product warranty, even if they
occur within the warranty period.
• Depending on conditions of use, the water-resistant features are not necessarily
guaranteed even during the warranty period.
*IPX2: The unit must be protected from water drops that fall vertically onto it when the unit is at an angle of
15 degrees or less.
Use in a wet environment (XW-SMA1 and XW-SMA4 only)
CAUTION
•XW-SMA1 and XW-SMA4 are not drip-proof. When using, prevent exposure to water. Do not use in
the following environments.
• Humid places
• Places where the product is easily exposed to water
• Near the beach or on the beach
This could cause rust.
Download from Www.Somanuals.com. All Manuals Search And Download.
Internal Rechargeable Lithium-ion Battery (XW-SMA3 only)
This device uses an internal rechargeable lithium-ion battery that should last the lifetime of the
device. If you suspect your battery may be dead, try charging it several times. If the battery does
not recharge, please contact us for repair information.
WARNING/DISPOSAL OF UNIT [For American Users, Canadian Users]
Please do NOT attempt to change the battery yourself. If the battery has died and you do not want
us to replace your battery, you should follow the disposal instructions below:
•Never dispose of used batteries/electronics with ordinary solid wastes, since they contain toxic
substances.
•Always dispose of used batteries/electronics in accordance with the prevailing community
regulations that apply to the disposal of batteries/electronics. If there are no local regulations
concerning battery/electronics disposal, please dispose of the device in a waste bin for electronic
devices.
•Many electronics retailers now recycle batteries and other electronic devices at no charge. Check to
see which ones in your area do so.
Installing the unit
•When installing this unit, make sure to put it on a level and stable surface.
Don’t install it on the following places:
- on a color TV (the screen may distort)
- near a cassette deck (or close to a device that gives off a magnetic field). This may interfere with
the sound.
- in direct sunlight
- in extremely hot or cold areas
- in places where there is vibration or other movement
- in places that are very dusty
- in places that have hot fumes or oils (such as near a kitchen stove)
CAUTION
•When in use, do not stand the device up, prop it up against anything or hang it from anything.
•Do not sit or stand on top of the device.
•When carrying the device, hold the entire device firmly. Do not swing the device around by the frame.
•Do not attach this unit to the wall or ceiling. It may fall off and cause injury.
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for buying this Pioneer product.
Please read through these operating instructions so that you will know how to operate your model properly. After you have
finished reading the instructions, put them in a safe place for future reference.
Contents
What’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Before using the remote control . . . . . . . . . . . . . . . . 10
Replace the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using the remote control. . . . . . . . . . . . . . . . . . . . . . . 11
01 Before you start
09 Additional information
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Playable file formats. . . . . . . . . . . . . . . . . . . . . . . . . . 41
Cautions on use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
When moving this unit . . . . . . . . . . . . . . . . . . . . . . . . .42
Place of installation . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Cleaning the product . . . . . . . . . . . . . . . . . . . . . . . . . .42
About network playback. . . . . . . . . . . . . . . . . . . . . . . 42
Windows Media Player . . . . . . . . . . . . . . . . . . . . . . . . .42
Playing Windows Media Audio (WMA) files . . . . . . . . .42
Windows Media DRM. . . . . . . . . . . . . . . . . . . . . . . . . .42
DLNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Content playable over a network . . . . . . . . . . . . . . . . . .43
Disclaimer for Third Party Content . . . . . . . . . . . . . . . .43
About playback behavior over a network. . . . . . . . . . . .43
aacPlus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
FLAC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
About iPod/iPhone/iPad. . . . . . . . . . . . . . . . . . . . . . . 44
About Wi-Fi® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Audio Artistry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
02 Connections
Connecting iPod/iPhone/iPad . . . . . . . . . . . . . . . . . . 12
Connecting to the network through the wired
or wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Connecting using LAN cable . . . . . . . . . . . . . . . . . . . . 12
Connecting using wireless LAN. . . . . . . . . . . . . . . . . . 12
Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
When turning on this unit for the first time . . . . . . . . 13
03 Part names and functions
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Rear panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
04 Connect to network
Network setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
After completing the network settings. . . . . . . . . . . . 25
Web Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Initial menu (System Information) . . . . . . . . . . . . . . . 27
Network Configuration . . . . . . . . . . . . . . . . . . . . . . . 27
Friendly Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
•
Illustrations featured in the Operating Instructions may
have been modified or simplified for ease of explanation,
and may therefore differ from the actual product
appearance.
05 iPod/iPhone/iPad playback
Confirming what iPod/iPhone/iPad models are
supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
How to confirm the version of the iPod/iPhone/iPad
software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Connecting your iPod/iPhone/iPad . . . . . . . . . . . . . . 30
Playing your iPod/iPhone/iPad . . . . . . . . . . . . . . . . . 30
06 Music server
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
About playable DLNA network devices . . . . . . . . . . . . 31
Using AirPlay on iPod touch, iPhone, iPad
and iTunes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
About the DHCP server function . . . . . . . . . . . . . . . . . 31
Playing audio files stored on PCs or other devices. . . 32
Connecting to the LAN network. . . . . . . . . . . . . . . . . . 32
Playback with DLNA . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using AirPlay to enjoy music . . . . . . . . . . . . . . . . . . . . 32
07 Other connections
Connecting auxiliary devices . . . . . . . . . . . . . . . . . . . 34
Listening to auxiliary devices . . . . . . . . . . . . . . . . . . . 34
08 Changing the settings
Setting Quick Start Mode . . . . . . . . . . . . . . . . . . . . . 35
Setting Quick Start Mode. . . . . . . . . . . . . . . . . . . . . . . 35
Canceling Quick Start Mode . . . . . . . . . . . . . . . . . . . . 35
Resetting the system . . . . . . . . . . . . . . . . . . . . . . . . . 35
Firmware Update. . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
9
En
Download from Www.Somanuals.com. All Manuals Search And Download.
01
Before you start
Chapter 1:
Before you start
WARNING
What’s in the box
About lithium battery
Please confirm that the following accessories are in the box
•
•
•
•
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used battery cells immediately after
replacement. Keep away from children. If swallowed,
please contact a doctor immediately.
Lithium batteries may present a fire or chemical burn
hazard if misused. Do not disassemble, heat above
100 ºC, or incinerate.
Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the life or
performance of batteries.
when you open it.
•
•
•
•
•
•
Remote Control
Lithium Battery (CR2025)*
Power Cord
AC Adapter
Quick Start Guide
Warranty Card
*The lithium battery has been factory installed in the remote
control unit.
Before using the remote control
The battery supplied with this unit is stored in the battery
casing. Remove the protective seal from the battery casing.
Caution
Incorrect use of batteries may result in such hazards as
leakage and bursting. Observe the following precautions:
•
Remove the battery if the unit isn’t going to be used for
a month or more. In the event of battery fluid leakage,
wipe up any fluid inside the case and install a new
battery.
•
When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country or area.
Note
•
When you notice a decrease in the operating range,
replace the battery.
“Perchlorate Material - special handling may apply. See
(Applicable to California, U.S.A.) “
Replace the battery
When replacing the battery, use a commercially available
Lithium CR2025 battery.
1
Flip the remote control and pull out the
battery holder by pushing the tab to the right.
2
Place a new battery in the casing.
Make sure the + side of the battery is facing up when you
place it in the space provided.
3
Push back the battery holder.
3
2
1
1
The battery included with the unit is to check initial
operations; it may not last over a long period.
10
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you start
01
Using the remote control
The remote has a range of about 7 m (23 ft.) at an angle of
about 30º from the remote sensor.
30°
on
input
netwo
rk
stand
by/on
input
volume
7 m (23 ft.)
input
vol
Keep in mind the following when using the remote control:
•
Make sure that there are no obstacles between the
remote and the remote sensor on the unit.
•
Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the unit’s
remote sensor.
•
•
Remote controllers for different devices can interfere
with each other. Avoid using remotes for other
equipment located close to this unit.
Replace the batteries when you notice a fall off in the
operating range of the remote.
11
En
Download from Www.Somanuals.com. All Manuals Search And Download.
02
Connections
Chapter 2:
Connections
Turn on the DHCP server function of your router.
If your router does not have a built-in DHCP server function,
you have to set up the network manually.
Caution
•
Be sure to turn off the power and unplug the power cord
from the power outlet whenever making or changing
connections.
See Connect to network on page 18.
Connecting using LAN cable
•
Connect the power cord after all the connections
between devices have been completed.
Router
LAN cable
LAN
3
2
1
WAN
(commercially
available)
Connecting iPod/iPhone/iPad
It is possible to listen to audio when iPod/iPhone/iPad is
connected to this unit. Open the terminal cover (XW-SMA3
only) (page 16).
Switch the unit into standby then connect your iPod/iPhone/
iPad to the USB terminal on the rear panel of this unit.
When the unit’s power is turned ON, the iPod/iPhone/iPad
connected to the unit will be charged.
PC1
PC2
When this unit is running by the built-in battery, iPod/iPhone/
LAN(10/100)
iPod/iPhone/iPad
iPad is not charged (XW-SMA3 only).
LAN(10/100)
iPod/iPhone/iPad
Connecting using wireless LAN
iPod/iPhone/iPad
Router
LAN
3
2
1
WAN
on
input
network
standby/o
n
input
volume
Connecting to the network through the
wired or wireless LAN
By connecting this unit to the network via the wired or
wireless LAN, you can play back audio files stored on devices
on the network.1
Open the terminal cover (XW-SMA3 only).
Connect the LAN connector on this unit to the LAN connector
on your router (with or without the built-in DHCP server
function) with a straight LAN cable (CAT 5 or higher). Also
wireless connection to the network is possible.
Note
1 • Photo or video files cannot be played back.
• With Windows Media Player 11 or 12, you can even play back copyrighted audio files on this unit.
12
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
02
Plugging in
About startup time
After you’ve finished making all connections, plug the unit
About 30 seconds are required between after the power
turns On until the unit is actually ready to use. The time
required for startup can be reduced by setting the Quick
Start Mode to On (page 35).
into an AC outlet.
Important
•
Before making or changing the connections, switch off
the power and disconnect the power cord from the AC
outlet.
Important
When using the built-in battery (XW-SMA3 only)
DC IN
AUX IN
•
Be sure to charge XW-SMA3 before using for the first
time.
AC adapter
(supplied)
•
•
Approximately 3 hours are required to fully recharge the
battery.
A fully charged battery provides approximately 4 hours of
use at maximum volume and approximately 6 hours at
50 % volume.
To AC outlet
•
•
•
Playing time with a fully charged battery changes
depending on functions used, frequency of use, ambient
temperature, speaker volume and other factors.
The furnished battery can be recharged about 300 times,
although it may be less depending on conditions of use
and storage.
When the AC adapter is not connected, the battery will
slowly drain even when the unit is in the standby mode.
As a result, if the unit is not used for an extended period
of time, recharging may be necessary before the unit can
be used again.
Power cord (supplied)
When turning on this unit for the first
time
1
Open the terminal cover (XW-SMA3 only).
2
Plug the supplied AC adapter into the DC IN
Warning
socket on the rear of the unit.
Plug the supplied power cord into the AC
•
•
Do not use any AC adapter other than the supplied unit,
since fire or shock may occur.
The supplied AC adapter is designed exclusively for use
with this unit. Never attempt to use it with any device for
which it was not expressly designed, since fires or
shocks may occur.
3
adapter then plug the other end into an AC
outlet.
4
Press standby/on button.
•
•
•
Do not use any power cord other than the one supplied
with this unit.
5
The on indicator will flash for about 30 to 40
seconds. After about 30 to 40 seconds, the on
indicator will light blue.
Do not use the supplied power cord for any purpose
other than this unit.
Ambient temperature when recharging the battery
should be between 5 ºC and 35 ºC. Outside this range of
temperatures, the battery protection circuit may operate,
preventing recharging.
13
En
Download from Www.Somanuals.com. All Manuals Search And Download.
03
Part names and functions
Chapter 3:
Part names and functions
Remote Control
1
(standby/on) button
Switches the unit between Standby and On.
2
Playback control buttons
Use when operating an iPod or AirPlay with this remote
control.
1
2
3
3
vol –/+ (volume –/+) button
Use to adjust the listening volume.
input
4
4
input button
Press to select the input source.
vol
14
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Part names and functions
03
Front panel
volume
standby/on input
on
input
network
1
2 3
4
5
6
7
1
on (power on) indicator
4
Battery indicator (XW-SMA3 only)
Displays the built-in battery charge status, or lights when the
built-in battery is being charged. The indicator changes as
noted below.
When the power is on, this indicator lights.
2
input indicator
When the input source changes, this indicator lights. The
• When the unit is connected to AC adapter
indicator’s color changes as noted below.
Lights blue - Battery charging is completed.
*When battery charging is completed on the standby
mode, the indicator lights off.
Lights purple - Battery is being charged.
*If the battery indicator intermittently lights purple, see
Additional information on page 37.
Light OFF - AUX IN
Lights blue - AirPlay
Lights red - iPod
Lights green - DLNA (DMR) Digital Media Renderer
3
network indicator
When the network status changes, this indicator lights. The
• When this unit is not connected to AC adapter
Lights blue - Battery charge is usable.
Lights red - Battery has less than one-half charge.
Flashes red - Battery charge is low.
*A fully charged battery provides approximately 4 hours
of use at maximum volume and approximately 6 hours
at 50 % volume.
indicator’s color changes as noted below.
Lights blue - good connection
Flashes blue - weak signal
Flashes red - connection failure
*In the event that other colors appear, see Network
setting on page 18.
*The battery indicator is not designed to function as an
accurate measure of remaining battery charging.
*If the battery indicator intermittently lights purple, see
Additional information on page 37.
5
standby/on button
Switches the unit between Standby and On.
15
En
Download from Www.Somanuals.com. All Manuals Search And Download.
03
Part names and functions
6
input button
Note
Select the input source.
•
•
When pressing the input button for 3 seconds while this
unit is power on, this unit switches to the Quick Start
Mode. In the Quick Start Mode, when AirPlay or DMR is
played, this unit automatically turns on (page 35).
When using the XW-SMA3, the Quick Start Mode can be
set only when the AC adapter is connected.
iPod AUX IN iPod (return to the beginning)
*When AirPlay or DMR play begins, the unit’s input
function automatically switches respectively to AirPlay
or DMR. If the power is then turned OFF and later
turned ON again, the unit will return to the input
function last selected before AirPlay or DMR began.
7
volume –/+ button
Use to adjust the listening volume.
The listening volume has a range from 0 to 50 (however, the
unit is not equipped with a display to visually indicate the
volume level).
Rear panel
Open the terminal cover before connecting other various devices to the unit (XW-SMA3 only). Before making or changing the
connections, switch off the power and disconnect the power cord from the AC outlet.
Movable range of the wireless
antenna
2
160°
100°
1
XW-SMA3
network setup
wireless direct
LAN(10/100)
iPod/iPhone/iPad
DC IN 15
V
AUX IN
SOUND TUNED
BY ANDREW JONES
Chief Speaker Engineer
Terminal Cover
3
4
5
6
1
Wireless antenna
Caution
Receives signals from wireless devices.
•
•
The terminal cover may be detached if pulled strongly
away from the unit (XW-SMA3 only). If the terminal cover
becomes detached, press the cover’s protruding pins
into the connector openings on the unit, then use a
narrow non-pointed stick or other implement to push
through from above. Take care not to injure your eyes or
fingers when doing this.
Do not rotate the wireless antenna beyond its movable
range as shown in the illustration, since damage may
occur.
2
network setup/wireless direct button
Use to set the wireless network (page 18).
3
LAN (10/100) connector
Connect this unit to other network devices using a LAN cable.
4
iPod/iPhone/iPad connector
Use to connect iPod/iPhone/iPad as an audio source. This
unit does not support any USB device other than iPod/
iPhone/iPad.
5
DC IN terminal
Connect to AC adapter.
6
AUX IN jack
Use to connect an auxiliary playback device (page 34).
16
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Part names and functions
03
•
Do not lift this device by holding the wireless antenna,
since damage or personal injury may result.
on
input
networ
k
standby
/on
input
volume
•
When using XW-SMA4, do not lift this device by holding
the recessed portion of the rear panel, since damage or
personal injury may result.
XW-SMA4
network setup
wireless direct
LAN(10/100)
iPod/iPhone/iPad
D
C
I
N
A
U
X
I
N
SOUND TUNED
BY ANDREW JONES
Chief Speaker Engineer
17
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Connect to network
Chapter 4:
Connect to network
Network setting
By connecting the unit to your home LAN, you can enjoy AirPlay and playback of music stored on your computer or other device.
•
•
For information regarding the format of files supported by this unit, see Playable file formats on page 41.
Methods of connection may vary depending on the device used. Confirm the type of unit, and follow the appropriate
instructions.
If you select method A, C or E, confirm the LAN cable is not connected to this unit.
Connecting to a router with WPS-PBC function
Connecting this
unit using wireless
LAN
(use this method under normal conditions)
A
LAN
WPS-PBC
3
2
1
WAN
Connecting to a router without
WPS-PBC function
If your computer or tablet
PC is equipped with
C
D
E
B
C
D
F
LAN
Connect this unit directly to your computer or
tablet PC. Settings must be performed from
the Web browser of the computer or tablet
PC.
3
2
1
WAN
wireless LAN function
If your computer or tablet
PC is not equipped with
wireless LAN function
(wired LAN only)
on
input
ne
twork
standby/on
input
volume
LAN
WPS-PBC
3
2
1
WAN
Connecting this unit to the router using an iPhone/iPod touch/iPad (with iOS
5.0 or later)
The same wireless LAN connection settings can be applied to this unit.
Connecting to a router with DHCP server function
Connecting this unit
using wired LAN
(this method should be used under normal conditions)
LAN
DHCP
3
2
1
WAN
LAN
If your computer or
tablet PC is equipped
with wireless LAN
function
3
2
1
WAN
When fixed IP must be set
(connecting to a router without DHCP
server function)
Your computer or tablet PC must be
connected directly to the unit, and settings
must be performed from a Web browser.
on
input
network
standby/on
input
volume
If your computer or tablet
PC is not equipped with
wireless LAN function
(wired LAN only)
LAN
DHCP
3
2
1
WAN
Wireless Direct Function
The Wireless Direct function allows the use of a direct wireless connection between this unit and a wireless LAN device, without the need for
a router.
Precautions when connecting this unit to a wireless LAN router
The SSID only supports use of single-byte alphanumeric characters, together with the underbar and certain other symbols. If using
another character coding, the SSID must be updated before making network settings. For more details regarding SSID, consult your
router’s operating instructions.
18
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect to network
04
5
The network connection settings will be
A: Connections for wireless LAN using WPS-
PBC function
performed automatically, and when the
connection is complete, the unit's indicator will
briefly change to flashing red, then light steadily
blue.
1
Confirm that the AC adapter and LAN cable
are not connected to the unit.
The indicator will flash blue when the signal is weak.
LAN(10/100)
iPod/iPhone/iPad
DC IN
AUX IN
on
input
network
blue
2
Connect the AC adapter, and press
B: Wired connection to a router with DHCP
server
standby/on button.
The on indicator will flash blue. Wait for about 30 to 40
seconds.
1
Disconnect the power cord from AC power
DC IN
AUX IN
before performing the connection between
volume
standby/on input
router and this unit.
Use a LAN cable to connect this unit and your router.
6
LAN(10/100)
iPod/iPhone/iPad
DC IN
AUX IN
3
When the on indicator stops flashing, press
the rear-panel network setup/wireless direct
button.
LAN
3
2
1
WAN
The network indicator will change from flashing red to
flashing purple.
2
Connect the AC adapter, and press
network setup
wireless direct
standby/on button.
The on indicator will flash blue. Wait for about 30 to 40
seconds.
on
input
network
DC IN
AUX IN
DC IN
AUX IN
volume
standby/on input
4
Within 2 minutes, press the router’s WPS
button.
6
For information regarding router operation, consult the
router’s Operating Instructions.
3
The on indicator's flashing will stop, and
when the power is fully turned on, the network
indicator will light blue.
WPS
on
input
network
WPS
blue
19
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Connect to network
4
When the network indicator lights red,
C: Connection settings from a Web browser
using a computer, iPhone, tablet PC or other
device supporting wireless LAN
connect to the network called “Pioneer
Setup:xxxxxx” from Wi-Fi network setting on
the computer, iPhone, tablet PC or other device.
The “xxxxxx” is the device's unique identifier number.
Not all characters may be displayed, depending on the device
used.
1
Confirm that the AC adapter and LAN cable
are not connected to the unit.
LAN(10/100)
iPod/iPhone/iPad
DC IN
AUX IN
iPod
Network
Wi-Fi Network
Wi-Fi
ON
Choose a Network...
Pioneer Setup:xxxxxx
• Consult the appropriate Operating Instructions for
information regarding operation of the computer, iPhone,
tablet PC or other device used.
• Since this kind of connection is not encoded, a minor
security risk may be involved.
2
Connect the AC adapter, and press
standby/on button.
The on indicator will flash blue. Wait for about 30 to 40
seconds.
DC IN
AUX IN
5
When the connection is established, boot
volume
standby/on input
your Web browser and access the URL noted
below to make settings for this unit.
The Web Control menu will appear.
6
3
When the on indicator stops flashing, press
and hold volume “-” button on the front panel,
and then press and hold network setup/wireless
SMA
direct button on the rear panel for 3 seconds.
The unit will begin rebooting (the on indicator will flash blue);
wait for about 30 to 40 seconds.
network setup
wireless direct
volume
standby/on input
For Safari
DC IN
AUX IN
Press Bookmark icon (
) at the upper left of the screen.
Click Bonjour list (a), and then select this unit's name
(“Friendly Name”) (b) in Bookmark.
6
a
SMA
b
20
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect to network
04
6
From the menu on the left, select “Network
9
If you are asked to input a password, input
Configuration”.
If you wish to change the Friendly Name, select “Friendly
Name” from the menu and change the name before selecting
“Network Configuration.”
it here.
Also, if input of a fixed IP is required, set DHCP to OFF here
and make the setting.
S1000.1000.0
XW-SMA1
XX:XX
X:X
XXX:XXX
X:X
X:X
10 When settings are completed, click on
7
When the Auto/Manual selection screen
Apply.
appears, select “Auto.”
If you are manually inputting the SSID or setting a fixed IP
with a wired connection, select “Manual.” For details, see
Network Configuration on page 27.
The unit will automatically power down. Confirm that the
router’s power is ON.
If you intend to use the unit in a wired configuration, use a
LAN cable to connect the unit to the router.
8
Select your router's SSID.
11 Press standby/on button.
If the SSID does not appear, either repeat step (6), or use step
The on indicator will flash blue. When the connection is
completed, the network indicator will change from flashing
red to steadily lighted blue.
(7) to select Manual and input the SSID manually.
The indicator will flash blue when the signal is weak.
The settings are completed.
volume
standby/on input
on
input
network
6
blue
21
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Connect to network
4
When the network indicator lights red, start
D: Using a Web browser on a computer
supporting wired LAN to make connecting
settings for the unit
your computer's Web browser, and access the
URL noted below to make settings for this unit.
The Web Control menu will appear.
1
Use a LAN cable to connect the unit to the
computer.
LAN(10/100)
iPod/iPhone/iPad
DC IN
AUX IN
SMA
For Safari
Press Bookmark icon (
Click Bonjour list (a), and then select this unit's name
(“Friendly Name”) (b) in Bookmark.
) at the upper left of the screen.
2
Connect the AC adapter, and press
standby/on button.
The on indicator will flash blue. Wait for about 30 to 40
seconds.
DC IN
AUX IN
volume
standby/on input
a
6
SMA
b
3
Wait for the network indicator to change
from flashing to steadily lighted red.
This may require up to 90 seconds or so.
5
From the menu on the left, select “Network
Configuration.”
If you wish to change the Friendly Name, select “Friendly
Name” from the menu and change the name before selecting
“Network Configuration.”
on
input
network
S1000.1000.0
XW-SMA1
XX:XX
X:X
XXX:XXX
X:X
X:X
22
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect to network
04
6
If using a wireless LAN connection, input the
9
Disconnect the LAN cable from the unit and
router’s SSID, then select the “Security” item set
on the router.
Also, if input of a fixed IP is required, set DHCP to OFF here
and make the setting. For details, see Network Configuration
on page 27.
confirm that the router’s power is ON.
If you intend to use the unit in a wired configuration, use a
LAN cable to connect the unit to the router.
LAN(10/100)
iPod/iPhone/iPad
10 Press standby/on button.
The on indicator will flash blue. When the power is completely
on (on indicator lights steadily blue), the network indicator
will light blue, indicating that settings are completed.
7
If a password is requested, input it here.
volume
standby/on input
on
input
network
6
blue
8
When settings are completed, click on
Apply.
The unit will automatically power down.
23
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Connect to network
4
Press and hold input button on the front
E: Connection settings using an iOS device
panel, and then press and hold network setup/
wireless direct button on the rear panel for 3
If you use an iPhone/iPod touch/iPad (iOS device with iOS 5.0
or later) with wireless LAN connection, apply the iOS device’s
connecting settings to this unit.
seconds.
A screen like the following should appear on the iOS device.
1
Confirm that the AC adapter and LAN cable
network setup
wireless direct
are not connected to the unit.
volume
standby/on input
DC IN
AUX IN
LAN(10/100)
iPod/iPhone/iPad
DC IN
AUX IN
6
5
Tap the “Allow” button.
2
Connect the AC adapter, and press
standby/on button.
The on indicator will flash blue. Wait for about 30 to 40
seconds.
DC IN
AUX IN
6
When the network indicator changes from
volume
flashing red to steadily lighted blue, the
connection is completed.
standby/on input
6
3
When the on indicator stops flashing, use
on
input
network
the Dock Connector to USB Cable to connect this
unit to the iPod touch/iPhone/iPad (iOS device
with iOS 5.0 or later).
blue
LAN(10/100)
iPod/iPhone/iPad
• Confirm that the iOS device has a wireless connection to
your router.
• Confirm that the iOS device’s screen lock is disabled.
24
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect to network
04
3
Confirm that the unit's on indicator stops
F: Wireless Direct Function
flashing. Hold the unit's rear-panel network
setup/wireless direct button depressed for 3
Important
seconds.
•
•
Wireless Direct should be used only as a temporary
connection under conditions where a normal router
cannot be used. This connection is not encoded, so the
music stream and music metadata will not be encrypted.
Wireless Direct is intended for use with smartphones in
their originally manufactured condition that receive
regular updates. If a smartphone has been modified
(such as “jailbreaking” or “unlocking” a phone), its
security is compromised, and the wireless connection
could result in unauthorized access or other intrusion.
Do not use a modified phone with Wireless Direct.
The unit will begin rebooting (the on indicator will flash blue);
wait for about 30 to 40 seconds.
network setup
wireless direct
on
input
network
DC IN
AUX IN
4
When the network indicator lights purple,
connect to the network called “Wireless
Direct:xxxxxx” from Wi-Fi network setting on
Note
the computer, iPhone, tablet PC or other device.
The “xxxxxx” is the device’s unique identifier number. Not all
characters may be displayed, depending on the device
•
•
Only one wireless device can be connected at the same
time.
Wireless Direct doesn’t have internet connection. When
you are using Wireless Direct, you will not be able to use
any kind of internet service.
used.
iPod
•
When power to this unit is turned OFF, the Wireless
Direct function is canceled, and the unit returns to the
network setting in effect prior to using the Wireless
Direct function.
Network
Wi-Fi Network
Wi-Fi
ON
Choose a Network...
Wireless Direct:xxxxxx
1
Confirm that the AC adapter and LAN cable
are not connected to the unit.
LAN(10/100)
iPod/iPhone/iPad
DC IN
AUX IN
Consult the appropriate Operating Instructions for
information regarding operation of the computer, iPhone,
tablet PC or other device used.
This completes the connection.
The network indicator remains lighted purple.
You may now operate your iPod/iPhone/iPad to perform
AirPlay, etc.
2
Connect the AC adapter, and press
standby/on button.
The on indicator will flash blue. Wait for about 30 to 40
seconds.
After completing the network settings
When you have completed the network settings, see Music
server on page 31 and enjoy playing music.
DC IN
AUX IN
volume
standby/on input
6
25
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Connect to network
Using UPnP function to obtain access:
Web Control
This unit supports UPnP, so you can access the Web Control
menu from a UPnP-supported device connected to the same
network. For details, consult the Operating Instructions for
the respective system.
For method C or D in Network setting on page 18, use the Web
Control menu to make the setting.
Also, you can access the Web Control menu after making the
network connection.
Access Web Control using a Safari Browser
When using Windows 7/Windows Vista
1
2
Click on Start
Documents.
1
Be sure this unit and your computer are
connected to the same wired or wireless
network.
From the Explorer menu on the left side of the
screen, select Network.
This unit will appear as an icon connected to the same
network.
2
Launch Safari on your computer.
3
Right-click on the icon and select “View device
3
Press Bookmark icon ( ) at the upper left
webpage”.
The Web Control menu can be accessed.
of the screen.
4
Click Bonjour list (a), and then select this
unit's name (Friendly Name) (b) in Bookmark.
XW-SMA1
a
b
When using Windows XP
1
2
Click on Start
My Network.
Click on “Display icons for UPnP devices connected
to the network”.
The icon for this unit will appear as connected to the same
network.
3
When the icon is double-clicked.
The Web Control menu can be accessed.
XW-SMA1
XXXXXX
XXXXXX
XXXXXX
XXXXXX
XW-SMA1
26
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect to network
04
2
Security
When using AUTO, this will be set automatically when
selecting SSID.
Initial menu (System Information)
When Web Control is accessed, the following menu will
appear. This menu can be used to confirm detailed
information about the unit.
Select the encryption method depending on SSID.
3
WEP Key/WPA Passphrase
If WEP is selected in step 2 Security, the WEP Key will be
displayed.
s1000.1000.0
XW-SMA1
Alternately, if WPA-PSK(TKIP), WPA-PSK(AES), WPA2-
PSK(TKIP), or WPA2-PSK(AES) is selected in Security, “WPA
Passphrase” will be displayed.
1
2
If you select None in the Security menu, no character string
will be displayed.
WEP Key
Displays the WEP key in the blank type.
WPA Passphrase
Displays the WPA Passphrase in the blank type. The WPA
Passphrase can be changed between 6 and 63 characters.
1
Network Configuration
4
DHCP
Select this when using methods C or D in Network setting on
page 18 to make initial connection settings.
Switches the DHCP setting between ON and OFF.
Under normal conditions, leave ON. If you wish to input a
fixed IP, set this to OFF and the following input item will be
requested.
2
Friendly Name
Select this to change the “Friendly Name.”
Item
Operation
IP address
Set the IP address.
Network Configuration
Subnet Mask
Default Gateway
Primary DNS Server
Set the Subnet Mask.
Set the Default Gateway.
Set the Primary DNS Server.
When using procedure C in Network setting on page 18,
select AUTO or MANUAL before using this menu.
AUTO
SSID will be searched automatically, and can be selected
from the next pull-down menu. This is the normal method to
be used.
Secondary DNS
Server
Set the Secondary DNS Server.
MANUAL
5
Apply
SSID and Security items must be input manually. Use this
method if the SSID is not displayed when using AUTO.
Press once settings have been completed. The unit will
automatically power down.
1
2
To use a wired connection thereafter, connect a LAN cable to
the router.
When using wireless connections, confirm that the LAN
cable is disconnected.
3
4
5
1
SSID
Using AUTO
Displays the recognized wireless access point. Select the
access point you wish to connect to.
Using MANUAL
The input must be no longer than 32 characters.
27
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Connect to network
Friendly Name
This menu can be used to change the name of this unit as
seen on the network.
28
En
Download from Www.Somanuals.com. All Manuals Search And Download.
iPod/iPhone/iPad playback
05
Chapter 5:
iPod/iPhone/iPad playback
Merely by connecting your iPod/iPhone/iPad to this unit, you
can enjoy high-quality sound from your iPod/iPhone/iPad.
How to confirm the version of the iPod/
iPhone/iPad software
Playback setting for iPod/iPhone/iPad music can be
performed from this unit or the iPod/iPhone/iPad itself.
1
2
From the top menu, select Settings.
From an iPod/iPhone/iPad, select Settings General.
Confirming what iPod/iPhone/iPad
Select About.
models are supported
The software version will be displayed.
The iPod/iPhone/iPad playable on this unit are shown below.1
iPod/iPhone
Audio
Control
iPod nano 3/4/5/6G
iPod touch 1/2/3/4G
iPhone
iPhone 3G/3GS
iPhone 4/4S
iPad/iPad 2
•
This system has been developed and tested for the
software version of iPod/iPhone/iPad indicated on the
website of Pioneer:
North America
http://pioneer.jp/homeav/support/ios/na/
Europe
http://pioneer.jp/homeav/support/ios/eu/
Asia and Oceania
http://pioneer.jp/homeav/support/ios/ao/
•
•
Installing software versions other than those indicated
on the website of Pioneer to your iPod/iPhone/iPad may
result in incompatibility with this system.
When using an iPod/iPhone/iPad not supported by this
unit, connect a commercially available cable with stereo
mini-plug to the unit’s AUX IN jack (page 34).
Note
1 • Pioneer does not guarantee that this unit plays iPod/iPhone/iPad models other than the ones specified.
• Some functions may be restricted depending on the model or software version.
•
iPod/iPhone/iPad is licensed for reproduction of non-copyrighted materials or materials the user is legally permitted to reproduce.
• Features such as the equalizer cannot be controlled using this system, and we recommend switching the equalizer off before
connecting.
• Pioneer cannot under any circumstances accept responsibility for any direct or indirect loss arising from any inconvenience or loss of
recorded material resulting from iPod/iPhone/iPad failure.
• For detailed instructions on using the iPod/iPhone/iPad, please refer to the manual supplied with the iPod/iPhone/iPad.
29
En
Download from Www.Somanuals.com. All Manuals Search And Download.
05
iPod/iPhone/iPad playback
The following operations are possible for iPod/iPhone/iPad.
Connecting your iPod/iPhone/iPad
Caution
Button
What it does
(play/
pause)
Press to start playback. During playback,
pause/unpause playback.
•
When connecting iPod/iPhone/iPad units, always use
the Dock Connector to USB Cable provided with iPod/
iPhone/iPad units, or a commercially available Dock
Connector to USB cable designed to support iPod/
iPhone/iPad.
(prev)
Press to return to the beginning of the currently
playing track or file. Press twice to move back to
the beginning of the previous track or file.
(next)
Press during playback to skip ahead to the
•
This unit does not provide the Dock Connector to USB
cable.
beginning of the next track or file.
input
Switches to the previous input.
1
2
Open the terminal cover (XW-SMA3 only).
Connect your iPod/iPhone/iPad.
vol –/+
(volume –/+)
Use to set the listening volume.
Important
•
If this unit cannot play your iPod/iPhone/iPad, perform
the following troubleshooting checks:
• Check whether the iPod/iPhone/iPad is supported by
this unit.
network setup
wireless direct
• Reconnect the iPod/iPhone/iPad to the unit. If this
doesn’t seem to work, try resetting your iPod/iPhone/
LAN(10/100)
iPod/iPhone/iPad
DC IN 15
V
AUX IN
SOUND TUNED
BY ANDREW JONES
iPad.
Chief Speaker Engineer
• Check the iPod/iPhone/iPad software is supported by
this unit.
•
If the iPod/iPhone/iPad cannot be operated, check the
following items:
iPod/iPhone/iPad
• Is the iPod/iPhone/iPad connected correctly?
Reconnect the iPod/iPhone/iPad to the unit.
• Is the iPod/iPhone/iPad experiencing a hangup? Try
resetting the iPod/iPhone/iPad, and reconnect it to the
unit.
Tip
•
•
•
When the unit’s power is turned ON, the iPod/iPhone/
iPad connected to the unit will be charged.
When this unit is running by the built-in battery, iPod/
iPhone/iPad is not charged (XW-SMA3 only).
When input is switched from iPod to another function,
the iPod/iPhone/iPad’s power will be turned off
automatically.
If the unit is set to standby when an iPod/iPhone/iPad is
connected, the iPod/iPhone/iPad will be turned off
automatically.
When no device is connected to the iPod/iPhone/iPad
connector, if the unit is not operated for 20 minutes or
more, the unit’s power will automatically turn OFF.
Playing your iPod/iPhone/iPad
Caution
•
When your iPod/iPhone/iPad is connected to this unit
and you wish to operate the iPod/iPhone/iPad directly,
be sure to hold the iPod/iPhone/iPad steady with the
other hand to prevent malfunctions due to faulty
contacts.
•
•
1
2
Connect your iPod/iPhone/iPad.
Press input to select iPod as the input
source.
The input indicator of the unit lights red.
30
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Music server
06
Chapter 6:
Music server
This unit can play audio files stored on PCs or other devices
on a Local Area Network (LAN).
Input to the unit will switch automatically when AirPlay is in
use.
The following operations can be performed when in AirPlay
mode:
•
Adjustment of the unit’s volume from iPod touch,
iPhone, iPad or iTunes.
Introduction
This unit allows you to listen to audio files on a computer or
other device connected to the unit via LAN interface. This
chapter describes the setup and playback procedures
required to enjoy these features. It is advisory that you also
refer to the operation manual supplied with your network
device.
Tip
•
•
A network environment is required to use AirPlay.
The unit’s name that shows up in the AirPlay UI on iPod
touch, iPhone, iPad and iTunes can be changed by
Friendly Name on Web Control (page 28).
AirPlay provided on this unit has been developed and
tested based on the software versions for the iPod touch,
iPhone, iPad and the software versions for iTunes that
are indicated on the Pioneer website.
•
•
Photo or video files cannot be played back.
With Windows Media Player 11 or Windows Media
Player 12, you can even play back copyrighted audio files
on this unit.
•
About playable DLNA network devices
North America
This unit allows you to play music on media servers
connected on an identical Local Area Network (LAN) as the
unit. This unit allows you to play files stored on the following
devices:
http://pioneer.jp/homeav/support/ios/na/
Europe
http://pioneer.jp/homeav/support/ios/eu/
Asia and Oceania
•
•
•
PCs running Microsoft Windows Vista or XP Service
Pack 3 with Windows Media Player 11 installed
PCs running Microsoft Windows 7 with Windows Media
Player 12 installed
DLNA 1.0 or 1.5-compatible digital media servers (on
PCs or other devices)
http://pioneer.jp/homeav/support/ios/ao/
•
AirPlay may not be compatible with iPod touch, iPhone,
iPad or iTunes software versions other than those
indicated on the Pioneer website.
Files stored in a PC or DMS (Digital Media Server) as
described above can be played via command from an external
Digital Media Controller (DMC). Devices controlled by this
DMC to play files are called DMRs (Digital Media Renderers).
This unit supports this DMR function. When in the DMR
mode, such operations as playing and stopping files can be
performed from the external controller. Volume adjustment
and the muting control are also possible.
About the DHCP server function
To play back audio files stored on devices on the network, you
must turn on the DHCP server function of your router.
In case your router does not have the built-in DHCP server
function, it is necessary to set up the network manually.
Otherwise, you cannot play back audio files stored on devices
on the network or listen to Internet radio stations. See
Network setting on page 18 for more on this.
•
If connection is made to a Digital Media Controller or
Digital Media Server that has not received DLNA
certification, the unit may not operate properly.
•
Depending on the external controller being used,
playback may be interrupted when the volume is
adjusted from the controller. In this case, adjust the
volume from the unit or remote control.
Using AirPlay on iPod touch, iPhone, iPad and
iTunes
AirPlay works with iPhone 4S, iPhone 4, iPhone 3GS, iPod
touch (4th, 3rd and 2nd generations), iPad 2, iPad with iOS 4.2
or later, and iTunes 10.1 (Mac and PC) or later.
To use AirPlay, select your unit on your iPod touch, iPhone,
iPad or in iTunes and start playback.1
Note
31
En
Download from Www.Somanuals.com. All Manuals Search And Download.
06
Music server
Operating AirPlay from an iPod/iPhone/iPad
Tap Music icon and start playing music.
Playing audio files stored on PCs or other
devices
1
Playback starts.
Connecting to the LAN network
For details on the connections, see page Connecting to the
network through the wired or wireless LAN on page 12.
Playback with DLNA
Perform the playback operation on the DMR device.
1
Confirm that this unit is connected on the
same network to a DMC device and a DMS
device (computer, etc.) in which music files are
stored.
2
Tap AirPlay icon ( ).
2
Select this unit's name (“Friendly Name”)
from the available device list.
When playback starts, the input indicator lights green.
For details regarding operation of the DMC device, consult
the operating instructions accompanying that device.
You can perform the following operations. Note that some
buttons are not available for operation depending on the
category currently being played back.
3
Select SMA.
The “xxxxxx” is the device's unique identifier number.
Button
input
What it does
Returns to the previous function.
Use to set the listening volume.
vol –/+
(volume –/+)
Using AirPlay to enjoy music
Confirm that the iPod touch, iPhone, iPad,
1
iTunes and this unit are connected to the same
wired or wireless network.
2
Play music on iPod touch, iPhone, iPad or
iTunes.
3
During playback, tap the AirPlay icon (
)
displayed on the iPod touch, iPhone, iPad or
iTunes.
4
Select this unit’s name (“Friendly Name”)
from the available device list.
32
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Music server
06
Operations using this unit's remote control
You can perform the following operations. Note that some
buttons are not available for operation depending on the
category currently being played back.
For iTunes, when the “Allow iTunes control from remote
speakers” function is set to ON, you can use following
buttons.
Button
What it does
(play/
Press to start playback. During playback, pause/
pause)
unpause playback.
(prev)
Press to return to the beginning of the currently
playing track or file. Press twice to move back to
the beginning of the previous track or file.
(next)
Press during playback to skip ahead to the
beginning of the next track or file.
input
Returns to the previous function.
vol –/+
Use to set the listening volume.
(volume –/+)
Note
•
During use of AirPlay or DMR input, if no music is played
or this unit’s controls are not operated for 20 minutes or
more, the unit’s power will automatically be switched
OFF.
33
En
Download from Www.Somanuals.com. All Manuals Search And Download.
07
Other connections
Chapter 7:
Other connections
Caution
Listening to auxiliary devices
Press input to select AUX IN as the input
source.
The input indicator does not light.
•
Before making or changing the connections, switch off
the power and disconnect the power cord from the
power outlet.
1
•
Open the terminal cover (XW-SMA3 only).
Note
2
Start playback of the auxiliary device.
•
•
If the AUX IN mini-plug jack is connected to auxiliary
phones jack, the volume of the unit will be adjusted by
the volume on the playback device. If the sound is
distorted after you lower the volume of the unit, try
lowering the volume on the auxiliary playback device.
This unit’s AUX IN jack is designed for 1 Vms inputs.
Some component CD/DVD players, however, are
designed for 2 Vms output; if one of these components
is connected to the unit, noise may be produced.
Note
•
When using the AUX input, if no cord with mini-plug is
connected to the AUX IN jacks, and this unit is not
operated for 20 minutes or more, the unit’s power will
automatically be switched off.
Connecting auxiliary devices
Connect the rear panel AUX IN mini-plug jack to your
auxiliary playback device.
Digital audio player, etc.
Stereo mini-plug cable
(commercially available)
DC IN
AUX IN
This unit’s rear panel
Note
•
If your iPod/iPhone/iPad is not supported by this unit's
iPod/iPhone/iPad jacks (page 29), use the method
noted above to connect your iPod/iPhone/iPad.
34
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the settings
08
Chapter 8:
Changing the settings
Canceling Quick Start Mode
Setting Quick Start Mode
1
Hold the input button depressed for 3
Quick Start Mode significantly reduces the time required for
startup. It also allows the unit to power on automatically using
AirPlay and DLNA. Follow the steps below to turn on Quick
Start Mode.
seconds when the unit is in the Quick Start
Mode.
The Quick Start Mode will be canceled.
The on indicator, input indicator and network indicator
each flashes twice.
Setting Quick Start Mode
1
2
Open the terminal cover (XW-SMA3 only).
Connect the AC adapter.
Resetting the system
Use this procedure to reset all system settings to the factory
DC IN
AUX IN
default.
Important
•
Disconnect all devices connected to this unit before the
operation.
1
Press standby/on.
3
Press the standby/on button.
The unit turns on.
After the power turns on, it takes approximately 30 seconds
for the unit to be ready to use. on indicator will go from
flashing to solid blue.
2
Press and hold input and standby/on on
the unit for 3 seconds.
After all the indicators on the front panel of the main unit
light, the unit turns off (standby mode).
volume
All the settings will be reset to the factory default next time the
standby/on input
unit turns on.
6
Note
4
Hold the input button depressed for 3
•
When using the XW-SMA3, after returning settings to
their factory defaults, remember to connect the AC
adapter. If the AC adapter is not connected, power
cannot be turned ON.
seconds.
The on indicator, input indicator and network indicator will
flash 4 times to signal Quick Start Mode has been turned on.
volume
standby/on input
6
35
En
Download from Www.Somanuals.com. All Manuals Search And Download.
08
Changing the settings
Firmware Update
You can update this unit’s firmware via Safari or Microsoft
Internet Explorer 8/9. Download the latest firmware for your
computer from the Pioneer website. The downloaded file will
be compressed in the ZIP format, and must be decompressed
before it can be used.
Note
•
•
Connect the AC adapter when using the XW-SMA3 (this
operation cannot be performed using battery power).
When updating the firmware, it is necessary to connect
the unit to a network by following the procedure (except
method F). See Network setting on page 18.
1
Access the Web Control.
See Web Control on page 26.
2
3
Click Firmware Update.
Press Start.
The Firmware Update Prepare screen is displayed. If the
screen does not switch automatically, click Click here.
4
Confirm the location of the newest firmware
(a), then press the Upload button (b).
The confirmation screen is displayed. If you continue the
firmware update, press Yes. Once the firmware update
process starts, you can’t stop it.
11
S1000
BCO_1000.fw
a
b
5
The firmware upload status screen is
displayed.
When the update is completed, unplug the power cord from
its AC outlet as instructed in the display.
Important
•
Never disconnect the AC power while updating is
underway.
36
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
09
Chapter 9:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this device,
check the points below. Sometimes the trouble may lie in another device. Investigate the other devices and electrical appliances
being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized
service center or your dealer to carry out repair work.
•
If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the
outlet and insert again to return to normal operating conditions.
General problem
Problem
Check
Remedy
Settings you have made have Was the power cord unplugged
Be sure to press standby/on on this unit or press
been cleared.
forcibly while this unit’s power was (standby/on) on the remote control and wait for the on
on?
indicator on the front panel display to turn off before unplugging the
power cord.
Difference in volume
between MP3, WMA, iPod/
iPhone/iPad, AUX.
This is not a problem with this unit. The volume may sound differently depending on the input source
and recording format.
This unit cannot be operated Are you operating from far away?
with the remote control.
Operate from within a distance of Operate within 7 m (23 ft.), 30° of
the remote sensor on the front panel (page 11).
Is the remote control sensor exposed The remote control signals may not be received properly if the
to direct sunlight or strong artificial remote control sensor is exposed to direct sunlight or strong
light from a fluorescent bulb, etc.?
artificial light from a fluorescent bulb, etc.
Are the batteries dead?
Replace the batteries (page 10).
The terminal cover has come
off (SMA3 only).
When using the XW-SMA3, the terminal cover may be detached if
pulled strongly away from the unit. If the terminal cover becomes
detached, press the cover’s protruding pins into the connector
openings on the unit, then use a narrow non-pointed stick or other
implement to push through from above. Take care not to injure
your eyes or fingers when doing this.
When an iPod/iPhone/iPad is connected
Problem
Check
Remedy
Can’t operate the iPod/
iPhone/iPad.
Make sure the iPod/iPhone/iPad is connected correctly (page 30).
Check whether the iPod/iPhone/iPad is supported by this unit
(page 29).
Also, try disconnecting the iPod/iPhone/iPad then reconnecting it.
If the iPod/iPhone/iPad has frozen, try resetting the iPod/iPhone/
iPad, and reconnect it to the unit.
The iPod/iPhone/iPad cannot
be recharged.
The iPod/iPhone/iPad can be recharged only when this unit’s
power is turned ON.
When using the XW-SMA3, the internal battery cannot be
recharged while the unit is operating on battery power.
The on indicator flashes red.
Confirm that the iPod/iPhone/iPad is connected properly. Try
disconnecting and reconnecting the iPod/iPhone/iPad.
There is a possibility of damage to the Dock connector's USB
cable. Try replacing the USB cable.
37
En
Download from Www.Somanuals.com. All Manuals Search And Download.
09
Additional information
Network
Problem
Check
Remedy
Cannot access to the
network.
The LAN cable is not firmly
connected.
Firmly connect the LAN cable (page 12).
The router is not switched on.
Switch on the router.
Playback does not start.
The device is currently disconnected Check whether the device is properly connected to this unit or the
from this unit or the power supply.
power supply.
The audio files stored on
devices on the network, such Windows Media Player 12 is not
as a PC, cannot be played
back.
Windows Media Player 11 or
Confirm that the computer has the following software installed:
Windows Media Player version 11 or 12, and server software
conforming to DLNA 1.0 or 1.5. Also be sure to set the server for
“media sharing” and “device selection.”
currently installed on your PC.
Procedures for operating Windows Media Player differs depending
on the computer’s OS and version of Windows Media Player. For
details consult the Microsoft website.
For details regarding operation of server software conforming to
DLNA 1.0 or 1.5, consult the instructions that came with your
software.
Confirm the file formats of the files you are trying to play with this
unit. Even though a file may have an extension otherwise playable
on this unit, it may not be playable or displayable due to individual
characteristics.
Audio files recorded in MPEG-4 AAC Audio files recorded in MPEG-4 AAC or FLAC cannot be played
or FLAC are being played back on
Windows Media Player 11 or
Windows Media Player 12.
back on Windows Media Player 11 or Windows Media Player 12. Try
using another server. Refer to the operation manual supplied with
your server.
The device connected to the network Check whether the device is affected by special circumstances or
is not properly operated. is in the sleep mode. Try rebooting the device if necessary.
The device connected to the network Try changing the settings for the device connected to the network.
does not permit file sharing.
The folder stored on the device
connected to the network has been
deleted or damaged.
Check the folder stored on the device connected to the network.
Network connections could be
restricted due to the computer’s
network settings, security settings,
etc.
Check the computer’s network settings, security settings, etc.
The LAN cable is currently
Connect the LAN cable properly (page 12).
disconnected.
Audio playback is
undesirably stopped or
disturbed.
The audio file currently being played Check whether the audio file was recorded in a format supported
back was not recorded in a format
by this unit.
playable on this unit.
Check whether the folder has been damaged or corrupted.
Even audio files listed as playable on this unit may sometimes not
be played back or displayed (page 41).
There is heavy traffic on the network Use 100BASE-TX to access the devices on the network.
with the Internet being accessed on
the same network.
There is a connection routed through There may be a shortage of bandwidth on the 2.4 GHz band used by
a wireless LAN on the same network. the wireless LAN. Make wired LAN connections not routed through
a wireless LAN.
Install away from any devices emitting electromagnetic waves on
the 2.4 GHz band (microwave ovens, game consoles, etc.). If this
does not solve the problem, stop using other devices that emit
electromagnetic waves.
38
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
09
Wireless LAN
Problem
Check
Remedy
Network cannot be accessed
via wireless LAN.
The computer may determine the presence/absence of a wireless
LAN in accordance with the presence/absence of the cable at the
time the unit’s power is turned on. When using a wireless LAN,
disconnect the LAN cable from this unit and then turn the unit OFF
and ON again.
This unit and base unit (wireless LAN Improve the wireless LAN environment by moving the unit and
router, etc.) are too far apart or there base unit closer together, etc.
is an obstacle between them.
There is a microwave oven or other
device generating electromagnetic
waves near the wireless LAN
environment.
Use the system in a place away from microwave ovens or others
device generating electromagnetic waves.
Avoid using devices generating electromagnetic waves as much as
possible when using the system with the wireless LAN.
Wireless LAN connections cannot be The unit must be set in order to establish wireless LAN
established between the unit and
connections. See Connecting using wireless LAN on page 12.
base unit (wireless LAN router, etc.).
The IP address settings of the unit
does not match the settings of the
wireless LAN router, etc.
Check the IP address settings of the unit (including the DHCP
setting).
If the unit’s DHCP setting is on, turn the unit’s power off, then turn
the power back on.
Check that the IP addresses of the unit match the settings of the
wireless LAN router, etc.
If the unit’s DHCP setting is off, set an IP address matching the
network of the base unit (wireless LAN router, etc.).
For example, if the wireless LAN router’s IP address is
“192.168.1.1”, set the unit’s IP address to “192.168.1.XXX” (*1), the
subnet mask to “255.255.255.0”, the gateway and DNS to
“192.168.1.1”.
(*1) Set the “XXX” in “192.168.1.XXX” to a number between 2 and
248 that is not assigned to other devices.
The access point is set to conceal the In this case, the SSID may not be displayed on the access point list
SSID.
screen. If not, set the SSID, etc., by making the wireless LAN
settings on the unit manually.
The SSID only supports use of single-byte alphanumeric characters,
together with the underbar and certain other symbols. If using
another character coding, the SSID must be updated before making
network settings. For more details regarding SSID, consult your
router's operating instructions.
The access point’s security settings The unit does not support WEP 152-bit length code key or shared
use WEP 152-bit length code key or key authentication.
shared key authentication.
It may be that the router has frozen. Press the router’s reset button
and try making the settings again.
Doesn’t play properly when
using the Wireless Direct
function.
The Wireless Direct function may not operate properly depending
on the condition of signal reception and the wireless LAN device
connected. In such cases, bring the wireless devices closer
together and in other ways improve the conditions for wireless
LAN’ reception.
39
En
Download from Www.Somanuals.com. All Manuals Search And Download.
09
Additional information
Battery (XW-SMA3 only)
Problem
Check
Remedy
Power won’t turn ON.
Check the battery’s remaining charge state. Connect the AC
adapter and charge the battery.
Can’t charge the battery.
Battery indicator flashes
purple intermittently (flashing
purple light or regular
flashing of purple and other
color light).
Is the accessory AC adapter connected properly? Try disconnecting
the AC adapter then reconnecting it.
Is the ambient temperature correct for charging? Charge the battery
only when the ambient temperature is between 5 ºC and 35 ºC.
Operating time is very short.
Is the ambient temperature too low? In cold environments, the
battery will provide shorter playing time.
Has the battery pack reached the end of its useful life? If time
required for recharging has become long, or playing time becomes
extremely short even after full recharging, the battery pack has likely
reached the end of its usable life.
A battery can ordinarily be recharged about 300 times, but this
number may be shorter depending on surrounding conditions
during play and storage.
If you wish to have your unit's battery replaced, consult your Pioneer
service station.
40
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
09
Category Extension Stream
Playable file formats
Sampling
frequency
32 kHz to 48 kHz
This unit supports the following file formats. Note that the
files formats listed below may not be playable. Also, the
compatibility of file formats varies depending on the server
(DMS) and controller (DMC) used. Check with your server and
controller to ensure the compatibility of file formats
supported by your server and controller.
MPEG-4 Quantization 16 bit
AAC LC bitrate
MPEG-4
.m4a
.aac
.3gp
.3g2
AAC
HE AAC Channel
2 ch
(AAC
•
If an attempt is made to play files with unsupported
formats, the sound may be intermittent or be
accompanied by noise. In such cases, confirm that the
file format is compatible with this unit.
Plus v1/ Bitrate
16 kbps to
320 kbps
2)
VBR/CBR
Supported/
Supported
Category Extension Stream
Sampling
frequency
32 kHz to 96 kHz
(Wired)
Sampling
frequency
32 kHz to 48 kHz
32 kHz to 48 kHz
Wireless
Quantization 16 bit
bitrate
(
)
MPEG-1/
MP3
Quantization 16 bit, 24 bit
bitrate
.mp3
2 Audio Channel
2 ch
<*>
FLAC
.flac
FLAC
Layer-3
Bitrate
8 kbps to
320 kbps
Channel
2 ch
Bitrate
—
VBR/CBR
Supported/
Supported
VBR/CBR
—
Sampling
frequency
32 kHz to 96 kHz
(Wired)
*
”MPEG Layer-3 audio decoding technology licensed from
Fraunhofer IIS and Thomson multimedia.”
32 kHz to 48 kHz
Wireless
(
)
WAV
.wav
LPCM
Quantization 16 bit, 24 bit
bitrate
Channel
2 ch
Sampling
32 kHz to 48 kHz
frequency
Quantization 16 bit
bitrate
WMA2/7/
8/9
WMA
.wma
Channel
2 ch
Bitrate
5 kbps to
320 kbps
VBR/CBR
Supported/
Supported
41
En
Download from Www.Somanuals.com. All Manuals Search And Download.
09
Additional information
•
Unplug the power cord from the power outlet when
cleaning this unit.
Cautions on use
When moving this unit
About network playback
When moving this unit, be sure to first disconnect the iPod/
iPhone/iPad, LAN cable or any other equipment connected to
the unit. Then press standby/on on this unit (or
(standby/on) on the remote control), wait for the on indicator
on the front panel to turn off, then unplug the power cord.
Damage may occur if the unit is transported or moved when
another device is connected to iPod/iPhone/iPad, LAN (10/
100) terminals, or AUX IN mini-plug jacks.
The network playback function such as Music Server of this
unit uses the following technologies:
Windows Media Player
See Windows Media Player 11/Windows Media Player 12 on
page 31 for more on this.
Playing Windows Media Audio (WMA) files
Place of installation
•
WMA is an audio compression technology developed by
•
Choose a stable place near the TV or stereo system being
Microsoft Corporation USA.
used with this unit.
•
These files can be encoded using Windows Media Player
Ver. 7, Ver. 7.1, Windows Media Player for Windows XP,
or Windows Media Player 9 Series.
•
Do not place this unit on top of a TV or color monitor.
Also install it away from cassette decks and other
devices easily affected by magnetic forces.
•
•
Windows Media is either a registered trademark or
trademark of Microsoft Corporation in the United States
and/or other countries.
When encoding your files, use only applications
approved by Microsoft Corporation. If a non-approved
application is used, it may not operate properly.
Avoid the following locations:
•
•
•
•
•
•
•
Places exposed to direct sunlight
Humid or poorly ventilated places
Places where the product is easily exposed to water
Extremely hot places
Places exposed to vibrations
Windows Media DRM
Places in which there is much dust or cigarette smoke
Places exposed to soot, steam or heat (kitchens, etc.)
Microsoft Windows Media Digital Rights Management
(WMDRM) is a platform to protect and securely deliver
content for playback on computers, portable devices and
network devices. Music Server functions as a WMDRM 10 for
networked devices. WMDRM protected content can only be
played on media servers supporting WMDRM.
Do not place objects on this unit
Do not place any objects on top of this unit.
Do not obstruct the ventilation holes
Do not use this unit on shaggy rugs, beds, sofas, etc., or
wrapped in cloth, etc. Doing so will prevent the heat from
dispersing, leading to damage.
Content owners use WMDRM technology to protect their
intellectual property, including copyrights. This device uses
WMDRM software to access WMDRM protected content. If the
WMDRM software fails to protect the content, content owners
may ask Microsoft to revoke the software’s ability to use
WMDRM to play or copy protected content. Revocation does not
affect unprotected content. When you download licenses for
protected content, you agree that Microsoft may include a
revocation list with the licenses. Content owners may require
you to upgrade WMDRM to access their content. If you decline
an upgrade, you will not be able to access content that requires
the upgrade.
Do not expose to heat
Do not place this unit on top of an amplifier or other device
that generates heat. When rack mounting it, to avoid the heat
given off by the amplifier or other audio device, place it on a
shelf below the amplifier.
•
•
Turn off the unit’s power when not using it.
Depending on signal conditions, striped patterns may
appear on a TV screen and noise may enter the sound of
radio broadcasts when the unit’s power is on. If this
happens, turn the unit’s power off.
This product is protected by certain intellectual property rights
of Microsoft. Use or distribution of such technology outside of
this product is prohibited without a license from Microsoft.
Cleaning the product
•
•
•
Clean this unit using a soft cloth. For tough dirt, apply
some neutral detergent diluted in 5 to 6 parts water to a
soft cloth, wring out thoroughly, wipe off the dirt, then
wipe again with a soft, dry cloth.
Alcohol, thinner, benzene, insecticides, etc., could
cause the print or paint to peel off. Also, leaving rubber
or vinyl products in contact with this unit for long periods
of time could mar the cabinet.
When using chemical-impregnated wipes, etc., read the
cautions included with the wipes carefully.
42
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
09
USE OF CONTENT. NO ORAL OR WRITTEN INFORMATION
OR ADVICE GIVEN BY PIONEER OR ITS CUSTOMER
SERVICES REPRESENTATIVES WILL CREATE ANY SUCH
WARRANTY.
DLNA
IN NO EVENT WILL PIONEER, ITS AFFILIATES, OR THEIR
RESPECTIVE OFFICERS, DIRECTORS, OR EMPLOYEES BE
LIABLE IN CONNECTION WITH YOUR USE OF THIRD PARTY
CONTENT SERVICES THROUGH THIS DEVICE FOR
PERSONAL INJURY OR SPECIAL, INCIDENTAL, INDIRECT
OR CONSEQUENTIAL DAMAGES OF ANY KIND, INCLUDING
WITHOUT LIMITATION DAMAGES FOR ATTORNEY’S FEES,
LOST DATA OR LOST PROFITS, REGARDLESS OF THE
THEORY OF LIABILITY AND WHETHER OR NOT ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL
PIONEER’S TOTAL LIABILITY TO YOU FOR ALL DAMAGES
ARISING FROM THE USE OR INABILITY TO USE THIRD
PARTY CONTENT SERVICES (OTHER THAN AS MAY BE
REQUIRED BY LAW IN CASES INVOLVING PERSONAL
INJURY) EXCEED $10.00. THE FOREGOING LIMITATIONS
WILL APPLY EVEN IF THE ABOVE REMEDY FAILS OF ITS
ESSENTIAL PURPOSE. IF ANY APPLICABLE AUTHORITY
HOLDS ANY PORTION OF THIS SECTION TO BE
DLNA CERTIFIED® Audio Player
The Digital Living Network Alliance (DLNA) is a cross-industry
organization of consumer electronics, computing industry
and mobile device companies. Digital Living provides
consumers with easy sharing of digital media through a wired
or wireless network in the home.
The DLNA certification logo makes it easy to find products
that comply with the DLNA Interoperability Guidelines. This
unit complies with DLNA Interoperability Guidelines v1.5.
When a PC running DLNA server software or other DLNA
compatible device is connected to this player, some setting
changes of software or other devices may be required. Please
refer to the operating instructions for the software or device
for more information.
DLNA®, the DLNA Logo and DLNA CERTIFIED® are
trademarks, service marks, or certification marks of the Digital
Living Network Alliance.
UNENFORCEABLE, THEN LIABILITY WILL BE LIMITED TO
THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW.
About playback behavior over a network
•
Playback may stall when the PC is switched off or any
media files stored on it are deleted while playing content.
Content playable over a network
•
If there are problems within the network environment
(heavy network traffic, etc.) content may not be displayed
or played properly (playback may be interrupted or
stalled). For best performance, a 100BASE-TX
connection between player and PC is recommended.
If several clients are playing simultaneously, as the case
may be, playback is interrupted or stalled.
Depending on the security software installed on a
connected PC and the setting of such software, network
connection may be blocked.
•
Even when encoded in a compatible format, some files
may not play correctly.
•
•
Movie or Photo files cannot be played back.
Some functions may not be supported depending on the
server type or version used.
•
•
•
Supported file formats vary by server. As such, files not
supported by your server are not displayed on this unit.
For more information check with the manufacturer of
your server.
Pioneer is not responsible for any malfunction of the player
and/or the Music Server features due to communication
error/malfunctions associated with your network connection
and/or your PC, or other connected equipment. Please
contact your PC manufacturer or Internet service provider.
Disclaimer for Third Party Content
ACCESS TO THIRD PARTY CONTENT SERVICES, INCLUDING
ALL ASSOCIATED FEATURES AND FUNCTIONALITIES, IS
PROVIDED “AS IS,” “AS AVAILABLE” AND AT THE USER’S
OWN RISK, WITHOUT WARRANTY OF ANY KIND. PIONEER
DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, IN
CONNECTION WITH ACCESS TO AND USE OF CONTENT
SERVICES THROUGH THIS DEVICE, INCLUDING WITHOUT
LIMITATION WARRANTIES OF MERCHANTABILITY,
Windows Media is either a registered trademark or trademark of
Microsoft Corporation in the United States and/or other
countries.
This product includes technology owned by Microsoft
Corporation and cannot be used or distributed without a license
from Microsoft Licensing, Inc.
Microsoft®, Windows®7, Windows®Vista, Windows®XP,
Windows®2000, Windows®Millennium Edition, Windows®98,
and WindowsNT® are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/
or other countries.
SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR
PURPOSE, AND NON-INFRINGEMENT. PIONEER DOES NOT
GUARANTEE, REPRESENT, OR WARRANT THAT CONTENT
SERVICES WILL BE FREE FROM ERRORS, INTERRUPTION,
LOSS, CORRUPTION, ATTACK, VIRUSES, INTERFERENCE,
HACKING, OR OTHER SECURITY INTRUSION, AND PIONEER
DISCLAIMS ANY LIABILITY IN CONNECTION WITH THE
FOREGOING. PIONEER IS NOT LIABLE OR RESPONSIBLE
FOR ANY LOSS OR DAMAGE ARISING FROM ACCESS TO OR
43
En
Download from Www.Somanuals.com. All Manuals Search And Download.
09
Additional information
aacPlus
About iPod/iPhone/iPad
The AAC decoder uses aacPlus developed by Coding
Technologies
(www.codingtechnologies.com).
FLAC
FLAC Decoder
Copyright © 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007
Josh Coalson
“Made for iPod,” “Made for iPhone” and “Made for iPad” mean
that an electronic accessory has been designed to connect
specifically to iPod, iPhone, or iPad, respectively, and has
been certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this
device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod, iPhone,
or iPad may affect wireless performance.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
•
Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
Apple, AirPlay, iPad, iPhone, iPod, iPod shuffle, iPod nano,
iPod touch, iTunes, Mac and Safari are trademarks of Apple
Inc., registered in the U.S. and other countries.
•
Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
The AirPlay logo is a trademark of Apple Inc.
•
Neither the name of the Xiph.org
Foundation nor the names of its contributors may be
used to endorse or promote products derived from this
software without specific prior written permission.
®
About Wi-Fi
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi
Alliance.
Wi-Fi CERTIFIEDTM, WMMTM, WPATM and WPA2TM are
certification marks of the Wi-Fi Alliance.
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Audio Artistry
Created by world-renowned speaker engineer Andrew Jones,
this speaker offers high performance and exceptional quality
to deliver a stunning music listening experience.
Chief Speaker Engineer
44
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
09
Specifications
•
Speaker section (XW-SMA1 and XW-SMA3)
•
Accessories
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bass-reflex type
System. . . . . . . . . . . . . . . . . . . . . . . . . 2-way 3 speaker system
Speakers:
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Lithium Battery (CR2025)* . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Power Cord
Woofer . . . . . . . . . . . . . . . . . . . .7.7 cm (3 1/16 in.) cone x 2
Tweeter. . . . . . . . . . . . . . 2.6 cm (1 1/16 in.) semi-dome x 1
Frequency range. . . . . . . . . . . . . . . . . . . . . . . . 50 Hz to 20 kHz
AC Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Quick Start Guide
Warranty Card
•
Speaker section (XW-SMA4)
*The lithium battery has been factory installed in the remote
control unit.
Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bass-reflex type
System. . . . . . . . . . . . . . . . . . . . . . . . . . 3-way 5speaker system
Speakers:
Note
Subwoofer . . . . . . . . . . . . . . . . 10 cm (3 15/16 in.) cone x 1
Woofer . . . . . . . . . . . . . . . . . . . .7.7 cm (3 1/16 in.) cone x 2
Tweeter. . . . . . . . . . . . . . 2.6 cm (1 1/16 in.) semi-dome x 2
Frequency range . . . . . . . . . . . . . . . . . . . . . 45 Hz to 20 kHz
•
•
Specifications and the design are subject to possible
modifications without notice, due to improvements.
This product is not designed for use in Japan.
•
Miscellaneous
Power consumption
XW-SMA1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 W
XW-SMA3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 W
XW-SMA4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..27 W
In standby mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.5 W
In standby mode (Quick Start Mode) . . . . . . . . . . . . . . . .3.5 W
Dimensions (without antenna):
Ubiquitous WPS2.0
Copyright© 2007-2011 Ubiquitous Corp.
XW-SMA1 and XW-SMA3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
320 mm (W) x 180 mm (H) x 145 mm (D)
12 5/8 in. (W) x 7 1/8 in. (H) x 5 3/4 in. (D)
XW-SMA4. . . . . . 360 mm (W) x 210 mm (H) x 169 mm (D)
14 3/16 in. (W) x 8 5/16 in. (H) x 6 11/16 in. (D)
Weight (without package):
XW-SMA1. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 kg (5.1 lbs)
XW-SMA3. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 kg (5.5 lbs)
XW-SMA4. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 kg (8.4 lbs)
•
AC adapter
Power requirements. . . . . . . . AC 100 V to 240 V, 50 Hz/60 Hz
Rated output:
XW-SMA1 and XW-SMA3 . . . . . . . . . . . . . . . . . DC 15 V, 4 A
XW-SMA4. . . . . . . . . . . . . . . . . . . . . . . . . . . DC 15 V, 4.95 A
•
Wireless LAN
Wireless LAN standard . . . . . . . . . . . . . . . . . . . IEEE802.11b/g
Frequency band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 GHz
Security . . . . . . . . . . . . . . . . . . . . . . . . . WEP, WPATM, WPA2TM
45
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC
Manufacturer:
EU Representative’s:
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku,
Kawasaki-shi, Kanagawa
212-0031, Japan
Pioneer Europe NV
Haven 1087, Keetberglaan 1,
9120 Melsele, Belgium
[*] XW-SMA1-K, XW-SMA1-W, XW-SMA3-K, XW-SMA3-W, XW-SMA4-K
English: Dansk:
Hereby, Pioneer, declares that this [*] is
Undertegnede Pioneer erklærer herved,
in compliance with the essential
requirements and other relevant
provisions of Directive 1999/5/EC.
at følgende udstyr [*] overholder de
væsentlige krav og øvrige relevante
krav i direktiv 1999/5/EF
Suomi:
Deutsch:
Pioneer vakuuttaa täten että [*]
tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen
mukainen.
Hiermit erklärt Pioneer, dass sich
dieses [*] in Übereinstimmung mit den
grundlegenden Anforderungen und den
anderen relevanten Vorschriften der
Richtlinie 1999/5/EG befindet". (BMWi)
Nederlands:
ǼȜȜȘȞȚțȐꢀ
Hierbij verklaart Pioneer dat het toestel
[*] in overeenstemming is met de
essentiële eisen en de andere
relevante bepalingen van richtlijn
1999/5/EG
ȂǼꢀȉǾȃꢀȆǹȇȅȊȈǹꢀ3LRQHHUꢀǻǾȁȍȃǼǿꢀ
ȅȉǿꢀ>ꢁ@ꢀȈȊȂȂȅȇĭȍȃǼȉǹǿꢀȆȇȅȈꢀȉǿȈꢀ
ȅȊȈǿȍǻǼǿȈꢀǹȆǹǿȉǾȈǼǿȈꢀȀǹǿꢀȉǿȈꢀ
ȁȅǿȆǼȈꢀȈȋǼȉǿȀǼȈꢀǻǿǹȉǹȄǼǿȈꢀȉǾȈꢀ
ȅǻǾīǿǹȈꢀꢂꢃꢃꢃꢄꢅꢄǼȀ
Français:
Par la présente Pioneer déclare que
l’appareil [*] est conforme aux
exigences essentielles et aux autres
dispositions pertinentes de la directive
1999/5/CE
Italiano:
Con la presente Pioneer dichiara che
questo [*] è conforme ai requisiti
essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva
1999/5/CE.
Svenska:
Härmed intygar Pioneer att denna [*]
står I överensstämmelse med de
väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår
av direktiv 1999/5/EG.
Español:
Por medio de la presente Pioneer
declara que el [*] cumple con los
requisitos esenciales y cualesquiera
otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE
Download from Www.Somanuals.com. All Manuals Search And Download.
Português:
3LRQHHUꢀL]MDYOMDꢆꢀGDꢀMHꢀWDꢀ>ꢁ@ꢀYꢀVNODGXꢀ]ꢀ
ELVWYHQLPLꢀ]DKWHYDPLꢀLQꢀRVWDOLPLꢀ
UHOHYDQWQLPLꢀGRORþLOLꢀGLUHNWLYHꢀ
ꢂꢃꢃꢃꢄꢅꢄ(6ꢇ
Pioneer declara que este [*] está
conforme com os requisitos essenciais
e outras disposições da Directiva
1999/5/CE.
3ULQꢀSUH]HQWDꢆꢀ3LRQHHUꢀGHFODUDꢀFDꢀDFHVWꢀ
[*] este in conformitate cu cerintele
esentiale si alte prevederi ale Directivei
1999/5/EU.
3LRQHHUꢀWtPWRꢀSURKODãXMHꢆꢀåHꢀWHQWRꢀ>ꢁ@ꢀMHꢀ
YHꢀVKRGČꢀVHꢀ]iNODGQtPLꢀSRåDGDYN\ꢀDꢀ
GDOãtPLꢀSĜtVOXãQêPLꢀXVWDQRYHQtPLꢀ
VPČUQLFHꢀꢂꢃꢃꢃꢄꢅꢄ(6
Eesti:
ɋꢀɧɚɫɬɨɹɳɟɬɨꢆꢀ3LRQHHUꢀɞɟɤɥɚɪɢɪɚꢆꢀɱɟꢀ
ɬɨɡɢꢀ>ꢁ@ꢀɨɬɝɨɜɚɪɹꢀɧɚꢀɨɫɧɨɜɧɢɬɟꢀ
ɢɡɢɫɤɜɚɧɢɹꢀɢꢀɞɪɭɝɢꢀɫɴɨɬɜɟɬɧɢꢀ
ɩɨɫɬɚɧɨɜɥɟɧɢɹꢀɧɚꢀȾɢɪɟɤɬɢɜɚꢀ
1999/5/EC.
.lHVROHYDJDꢀNLQQLWDEꢀ3LRQHHUꢀVHDGPHꢀ
>ꢁ@ꢀYDVWDYXVWꢀGLUHNWLLYLꢀꢂꢃꢃꢃꢄꢅꢄ(hꢀ
S}KLQ}XHWHOHꢀMDꢀQLPHWDWXGꢀGLUHNWLLYLVWꢀ
WXOHQHYDWHOHꢀWHLVWHOHꢀDVMDNRKDVWHOHꢀ
sätetele.
Polski:
Magyar:
1LQLHMV]\Pꢀ3LRQHHUꢀRĞZLDGF]DꢆꢀĪHꢀ>ꢁ@ꢀ
MHVWꢀ]JRGQ\ꢀ]ꢀ]DVDGQLF]\PLꢀZ\PRJDPLꢀ
RUD]ꢀSR]RVWDá\PLꢀVWRVRZQ\PLꢀ
$OXOtURWWꢆꢀ3LRQHHUꢀQ\LODWNR]RPꢆꢀKRJ\ꢀDꢀ>ꢁ@ꢀ
PHJIHOHOꢀDꢀYRQDWNR]yꢀDODSYHW}ꢀ
N|YHWHOPpQ\HNQHNꢀpVꢀD]ꢀꢂꢃꢃꢃꢄꢅꢄ(&ꢀ
LUiQ\HOYꢀHJ\pEꢀHO}tUiVDLQDNꢇ
SRVWDQRZLHQLDPLꢀ'\UHNW\Z\ꢀꢂꢃꢃꢃꢄꢅꢄ(&
Norsk:
3LRQHHUꢀHUNO UHUꢀKHUYHGꢀDWꢀXWVW\UHWꢀ>ꢁ@ꢀHUꢀ
LꢀVDPVYDUꢀPHGꢀGHꢀJUXQQOHJJHQGHꢀNUDYꢀ
RJꢀ¡YULJHꢀUHOHYDQWHꢀNUDYꢀLꢀGLUHNWLYꢀ
1999/5/EF.
$UꢀãRꢀ3LRQHHUꢀGHNODUƝꢆꢀNDꢀ>ꢁ@ꢀDWELOVWꢀ
'LUHNWƯYDVꢀꢂꢃꢃꢃꢄꢅꢄ(.ꢀEnjWLVNDMƗPꢀ
SUDVƯEƗPꢀXQꢀFLWLHPꢀDUꢀWRꢀVDLVWƯWDMLHPꢀ
QRWHLNXPLHPꢇ
Íslenska:
âLXRꢀ3LRQHHUꢀGHNODUXRMDꢆꢀNDGꢀãLVꢀ>ꢁ@ꢀ
DWLWLQNDꢀHVPLQLXVꢀUHLNDODYLPXVꢀLUꢀNLWDVꢀ
ꢂꢃꢃꢃꢄꢅꢄ(%ꢀ'LUHNW\YRVꢀQXRVWDWDVꢇ
+pUꢀPHèꢀOêVLUꢀ3LRQHHUꢀ\ILUꢀìYtꢀDèꢀ>ꢁ@ꢀHUꢀtꢀ
VDPU PLꢀYLèꢀJUXQQNU|IXUꢀRJꢀDèUDUꢀ
NU|IXUꢆꢀVHPꢀJHUèDUꢀHUXꢀtꢀWLOVNLSXQꢀ
1999/5/EC
Malti:
Hrvatski:
+DZQKHNNꢆꢀ3LRQHHUꢀMLGGLNMDUDꢀOLꢀGDQꢀ>ꢁ@ꢀ
MLNNRQIRUPDꢀPDOꢈƫWLƥLMLHWꢀHVVHQ]MDOLꢀXꢀPDꢀ
SURYYHGLPHQWLꢀRƫUDMQꢀUHOHYDQWLꢀOLꢀKHPPꢀ
ILGꢈ'LUUHWWLYDꢀꢂꢃꢃꢃꢄꢅꢄ(&
2YLPHꢀWYUWNDꢀ3LRQHHUꢀL]MDYOMXMHꢀGDꢀMHꢀ
ovaj [*@ꢀXꢀVNODGXꢀRVQRYQLPꢀ]DKWMHYLPDꢀLꢀ
RVWDOLPꢀRGUHGEDPDꢀ'LUHNWLYHꢀ
1999/5/EC.
3LRQHHUꢀWêPWRꢀY\KODVXMHꢆꢀåHꢀ>ꢁ@ꢀVSĎĖDꢀ
]iNODGQpꢀSRåLDGDYN\ꢀDꢀYãHWN\ꢀSUtVOXãQpꢀ
XVWDQRYHQLDꢀ6PHUQLFHꢀꢂꢃꢃꢃꢄꢅꢄ(6ꢇ
R-TTE-24L_C1_En
Download from Www.Somanuals.com. All Manuals Search And Download.
To register your product, find the nearest authorized service location, to
purchase replacement parts, operating instructions, or accessories,
please go to one of following URLs :
Pour enregistrer votre produit, trouver le service après-vente agréé le plus
proche et pour acheter des pièces de rechange, des modes d’emploi ou
des accessoires, reportez-vous aux URL suivantes :
In the USA/Aux Etats-Unis
In Canada/Aux Canada
S018_B1_EnFr
Discover the benefits of registering your product online at
© 2012 PIONEER CORPORATION.
All rights reserved.
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270
K002_B3_En
<ARI7025-B>
Download from Www.Somanuals.com. All Manuals Search And Download.
|