Pioneer Portable CD Player DEH P6800MP User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DEH-P6800MP

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Printed in Thailand

Imprimé en Thaïlande

<XRD7112-A/N> UC

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the Units

Note:

•

This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

ational vehicle, truck, or bus, check the battery

voltage.

•

When an external power amp is being used with

this system, be sure not to connect the blue/white

lead to the amp’s power terminal. Likewise, do not

connect the blue/white lead to the power terminal

of the auto-antenna. Such connection could cause

excessive current drain and malfunction.

To avoid a short-circuit, cover the disconnected

lead with insulating tape. Insulate the unused

speaker leads without fail. There is a possibility of

a short-circuit if the leads are not insulated.

To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side

is black. Connect the connectors of the same

colors correctly.

If this unit is installed in a vehicle that does not

have an ACC (accessory) position on the ignition

switch, the red lead of the unit should be connected

to a terminal coupled with ignition switch ON/OFF

operations. If this is not done, the vehicle battery

may be drained when you are away from the vehi-

cle for several hours. (Fig.1)

•

To avoid shorts in the electrical system, be sure to

disconnect the ≠ battery cable before beginning

installation.

Refer to the owner’s manual for details on

connecting the power amp and other units, then

make connections correctly.

Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

Route and secure all wiring so it cannot touch any

moving parts, such as the gear shift, handbrake and

seat rails. Do not route wiring in places that get

hot, such as near the heater outlet. If the insulation

of the wiring melts or gets torn, there is a danger of

the wiring short-circuiting to the vehicle body.

•

Don’t pass the yellow lead through a hole into the

engine compartment to connect to the battery. This

will damage the lead insulation and cause a very

dangerous short.

•

Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

Never feed power to other equipment by cutting

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

•

When replacing the fuse, be sure to only use a fuse

of the rating prescribed on this unit.

Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

the left and right ≠ speaker leads are common.

ACC position

No ACC position

Fig. 1

•

Speakers connected to this unit must be high-

power with minimum rating of 50 W and imped-

ance of 4 to 8 ohms. Connecting speakers with out-

put and/or impedance values other than those

noted here may result in the speakers catching fire,

emitting smoke or becoming damaged.

When this product’s source is switched ON, a con-

trol signal is output through the blue/white lead.

Connect to an external power amp’s system remote

control or the car’s Auto-antenna relay control ter-

minal (max. 300 mA 12 V DC). If the car features

a glass antenna, connect to the antenna booster

power supply terminal.

•

The black lead is ground. Please ground this lead

separately from the ground of high-current prod-

ucts such as power amps.

If you ground the products together and the ground

becomes detached, there is a risk of damage to the

products or fire.

•

Cords for this product and those for other products

may be different colors even if they have the same

function. When connecting this product to another

product, refer to the supplied manuals of both

products and connect cords that have the same

function.

Download from Www.Somanuals.com. All Manuals Search And Download.

7 When not connecting a rear speaker lead to a Subwoofer

Power amp

(sold separately)

Connecting cords with RCA pin

plugs (sold separately)

Antenna jack

Rear output

Power amp

(sold separately)

15 cm (5-7/8 in.)

16 cm (6-1/4 in.)

Front output

This product

Power amp

(sold separately)

Subwoofer output

IP-BUS input (Blue)

Fuse

(10 A)

Jack for the Wired Remote Control

Please see the Instruction Manual for the

Wired Remote Control (sold separately).

Multi-CD player

(sold separately)

IP-BUS cable

Blue/white

To system control terminal of the power amp or

Auto-antenna relay control terminal (max. 300

mA 12 V DC).

System remote control

Yellow/black

If you use an equipment with Mute function, wire this

lead to the Audio Mute lead on that equipment. If not,

keep the Audio Mute lead free of any connections.

≠

Front speaker

Yellow

≠

To terminal always supplied with power regardless of

ignition switch position.

Red

White

Gray

To electric terminal controlled by ignition switch (12

V DC) ON/OFF.

≠

Front speaker

Right

≠

White/black

Green

Gray/black

Violet

Orange/white

To lighting switch terminal.

Left

≠

Rear speaker

Black (ground)

≠

To vehicle (metal) body.

Green/black

Violet/black

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

≠

Rear speaker

Subwoofer

≠

Perform these connections when using the

optional amplifier.

Subwoofer

≠

Fig. 2

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the Units

7 When using a Subwoofer without using the optional amplifier

Antenna jack

Subwoofer output

16 cm (6-1/4 in.)

15 cm (5-7/8 in.)

Front output

This product

Subwoofer output

IP-BUS input (Blue)

Fuse

(10 A)

Jack for the Wired Remote Control

Please see the Instruction Manual for the

Wired Remote Control (sold separately).

Multi-CD player

(sold separately)

IP-BUS cable

Blue/white

To system control terminal of the power amp or

Auto-antenna relay control terminal (max. 300

mA 12 V DC).

Yellow/black

If you use an equipment with Mute function, wire this

lead to the Audio Mute lead on that equipment. If not,

keep the Audio Mute lead free of any connections.

Yellow

To terminal always supplied with power regardless of

ignition switch position.

Red

White

Gray

To electric terminal controlled by ignition switch (12

V DC) ON/OFF.

≠

Front speaker

≠

White/black

Green

Gray/black

Violet

Orange/white

To lighting switch terminal.

Left

Right

≠

Black (ground)

To vehicle (metal) body.

Subwoofer

≠

Green/black

Violet/black

Note:

Change the initial setting of this unit (refer to the Operation

Manual). The subwoofer output of this unit is monaural.

Fig. 3

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Note:

•

Before making a final installation of the unit, tem-

porarily connect the wiring to confirm that the con-

nections are correct and the system works

properly.

•

If installation angle exceeds 60° from horizontal,

the unit might not give its optimum performance.

(Fig. 4)

•

Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts

can cause malfunctions.

Consult with your nearest dealer if installation

requires the drilling of holes or other modifications

of the vehicle.

Install the unit where it does not get in the driver’s

way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

The semiconductor laser will be damaged if it

overheats, so don’t install the unit anywhere hot

— for instance, near a heater outlet.

60°

Fig. 4

DIN Front/Rear-mount

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or

“Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit

chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 5)

Holder

After inserting the holder into the

dashboard, then select the appropriate

tabs according to the thickness of the

dashboard material and bend them.

(Install as firmly as possible using the

top and bottom tabs. To secure, bend

the tabs 90 degrees.)

Dashboard

182

Rubber bush

Screw

Fig. 5

Download from Www.Somanuals.com. All Manuals Search And Download.

Removing the unit (Fig. 6) (Fig. 7)

Frame

To remove the frame, extend top and

bottom of the frame outwards in

order to unlock it. (When reattaching

the frame, point the side with a

groove downwards and attach it.)

• It becomes easy to remove the

frame if the front panel is released.

Fig. 6

Insert the supplied extraction keys

into the unit, as shown in the figure,

until they click into place. Keeping

the keys pressed against the sides of

the unit, pull the unit out.

Fig. 7

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

DIN Rear-mount

Installation using the screw holes on the side of the unit

1. Remove the frame. (Fig. 8)

Frame

To remove the frame, extend top and

bottom of the frame outwards in

order to unlock it. (When reattaching

the frame, point the side with a

groove downwards and attach it.)

• It becomes easy to remove the

frame if the front panel is released.

Fig. 8

2. Fastening the unit to the factory radio mounting bracket.

(Fig. 9) (Fig. 10)

Select a position where the screw holes of the bracket and

the screw holes of the head unit become aligned (are fitted),

and tighten the screws at 2 places on each side. Use either

truss screws (5 × 8 mm) or flush surface screws

(5 × 9 mm), depending on the shape of the screw holes in

the bracket.

Fig. 9

S1c1rew

Dashboard or Console

Factory radio mounting br1a2cket

Fig. 10

Download from Www.Somanuals.com. All Manuals Search And Download.

Fixing the front panel

If you do not operate the removing and attaching the front panel function, use the supplied

fixing screw to fix the front panel to this unit.

Fixing screw

Fig. 11

Download from Www.Somanuals.com. All Manuals Search And Download.

Peavey Musical Instrument Amplifier Bass Amplification System User Manual
Peavey Musical Instrument Amplifier CKS Series User Manual
Philips Headphones SHH9700 User Manual
Philips Microcassette Recorder LFH3200 User Manual
Philips Stereo System DC910W User Manual
Philips Stereo System SWA3302S User Manual
Philips Universal Remote SRU4006 27 User Manual
PLUS Vision Projector V 1100Z User Manual
Polaroid Portable DVD Player PDU 1063 User Manual
Precor Exercise Bike EC 850 User Manual