BDR-203/BDC-203
Command Reference Manual
Version 1.01
Feb. 13, 2009
PIONEER CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.21.1 Reading Speed..................................................................................................................................................37
4.21.2 Writing Speed...................................................................................................................................................38
4.22 WRITE (10), WRITE (12) Command......................................................................................................................39
4.23 WRITE BUFFER Command...................................................................................................................................39
Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
1 Introduction
This document specifies a command set for BDR-203/BDC-203. (Hereinafter referred to as "drive") BDR-203 is a BD writer
drive. BDC-203 is a BD combo drive. BDC-203 does not write to BD-R/RE disc.
The drive fundamentally complies with SFFC INF-8090i standard.
The drive complies with Information Technology Multimedia Commands-5 (MMC-5) Draft Revision 1b prior to SFFC
INF-8090i standard, when a +R or a +RW disc is inserted in the drive.
The drive complies with Blu-ray Disc (BD) Multi-media Command Set Description Draft Version 1.0 prior to SFFC INF-8090i
specification, when a BD is inserted in the drive.
In some cases, the drive executes unique operation that is not described in the standards.
This document describes details of such unique operation for each command or disc.
For More Information about SFFC INF-8090i, refer FTP site at:
For More Information about Information Technology Multimedia Commands-5 (MMC-5) Draft Revision 1b, refer a site at:
1.1 Change History
Version 1.00 created on Feb.12, 2009.
Version 1.01 created on Feb.13, 2009.
2.1 SATA version is changed.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
2 Interface
The drive supports Serial ATA interface.
2.1 SATA version
The drive complies with the Serial ATA Revision 2.6. The data transfer mode is General1 1.5GBits/sec.
2.2 Drive Information
The data returned by INQUIRY command covers the following information.
Vendor name:
Product collation data:"BD-RW
“BD-ROM BDC-203” (combo)
“PIONEER ”
BDR-203" (writer)
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
3 DRIVE Descriptions
3.1 Compatible Media
The drive supports reading of BD-ROM, BD-R/RE Disc, CD-ROM/-R/-RW Disc, DVD-ROM/-R/-RW/RAM/-R DL Disc and
+R/+RW/+R DL Disc and writing of BD-R/RE Disc (except BDC-203), CD-R/-RW Disc, DVD-R/-RW/RAM/-R DL Disc and
+R/+RW/+R DL. (Except 8cm disc with an adaptor)
3.2 Power Condition
The drive is provided with 4 power conditions including active, idle, standby and sleep.
The power consumption in the active and idle conditions is identical while that in the standby and sleep conditions is also
identical. The disc keeps rotating in the active and idle conditions while it is stopped in the standby and sleep conditions.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4 Packet Commands
The following commands are implemented in the drive.
In case of BDC-203, the following commands are not performed for BD-R/RE; CLOSE TRACK/SESSION, FORMAT UNIT,
RESERVE TRACK, SEND DISC STRUCTURE, SEND OPC INFORMATION, SYNCRONIZE CACHE, WRITE(10),
WRITE(12), and WRITE AND VERIFY commands.
Table 1– Packet Commands
Operation
code
Reference
MMC-5
6.2
6.3
6.5
6.6
6.7
6.8
6.9
Command Description
SFF8090i
17.1
This document
A1h
5Bh
04h
46h
4Ah
ACh
12h
4Ch
4Dh
BDh
55h
5Ah
4Bh
45h
A5h
47h
BCh
1Eh
28h
A8h
3Ch
5Ch
25h
BEh
B9h
51h
ADh
23h
44h
42h
43h
52h
58h
A4h
03h
53h
BAh
2Bh
5Dh
1Dh
BFh
A3h
54h
BBh
A7h
B6h
1Bh
4Eh
35h
00h
2Fh
2Ah
AAh
17.2
17.3
17.4
17.5
17.6
17.7
PAUSE/RESUME Command
PLAY AUDIO (10) Command
PLAY AUDIO (12) Command
PLAY AUDIO MSF Command
17.9
6.11
6.12
6.13
17.10
17.11
17.12
17.13
17.14
PREVENT / ALLOW MEDIUM REMOVAL Command
READ(10) Command
READ(12) Command
17.15
17.16
1.17
1718
17.19
17.20
17.21
17.22
17.23
17.24
17.25
6.14
6.15
6.16
6.17
6.18
6.19
6.20
6.21
6.22
6.23
6.24
READ CD Command
READ CD MSF Command
READ DISC STRUCTURE Command
READ FORMAT CAPACITIES Command
READ HEADER Commd
READ SUBCHANNEL Command
READ TOC/PMA/ATIP Command
READ TK INFORMATION Command
REPAIR NE Command
REPORT KEY Command
RESERVE TRACK Command
SCAN Command
SEEK (10) Command
SEND CUE SHEET
SEND DIAGNOSTIC Command
SEND DISC STRUCTURE Command
SEND KEY Command
SEND OPC INFORMATION Command
SET READ AHEAD Command
START/STOP UNIT Command
STOP PLAY/SCAN Command
SYNCHRONIZE CACHE Command
TEST UNIT READY Command
VERIFY(10) Command
17.26
17.27
17.28
17.29
17.30
17.31
17.32
17.33
17.34
17.35
6.26
6.27
6.28
6.29
6.30
6.31
6.32
6.33
17.36
17.38
17.39
17.40
17.41
17.42
17.43
17.44
17.45
17.46
17.47
17.48
17.49
6.34
6.35
6.36
6.37
6.38
6.39
6.40
6.41
6.42
6.43
6.44
6.45
WRITE (10) Command
WRITE (12) Command
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
Operation
code
Reference
MMC-5
6.46
6.47
Command Description
WRITE AND VERIFY Command
SFF8090i
17.50
17.51
This document
2Eh
3Bh
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.1 BLANK Command
This command is valid for CD-RW and DVD-RW media.
The Immed bit is supported.
The READ DISC INFORMATION Command, the READ TRACK INFORMATION Command and the TEST UNIT READY
Command are used to detect completion of the blank operation. While blank operation is performed by the BLANK Command
that the Immed bit is set to one, the drive terminates these commands with the Check Condition status, LOGICAL UNIT NOT
READY, OPERATION IN PROGRESS (2/04/07).
The drive supports following Blanking Type for CD-RW and DVD-RW media.
Table 2 - Blank Type
Code
000b
001b
010b
011b
100b
101b
110b
Name
CD-RW media
DVD-RW media
Blank the disc
Yes
Yes
No
No
Yes
No
Yes
Yes
-
No
No
No
No
Minimally blank the disc
Blank a Track
Unreserved a Track/RZone
Blank a Track/RZone Tail
Unclose the last Session/Border
Erase Session/Border
No
4.2 CLOSE TRACK/SESSION Command
The Immed bit is supported.
The READ DISC INFORMATION Command or READ TRACK INFORMATION Command is used to detect completion of
the close operation. During a close operation performed by the CLOSE TRACK/SON Command whose Immed bit is set to
one, the drive terminates these commands with the Check Condition status, LOGIL UNIT NOT READY, OPERATION IN
PROGRESS (2/04/07).
Note: The TEST UNIT READY Command may be used to identify the cmpletion of close operation.
The valid Close Function field values are extended for handling the +R/+RW media in the MMC-5 rather than the SFFC
INF-8090i.
This command is not valid for BD-RE.
Table 3 – Valid Close Function and Media
Close
Media
Function
000b
+RW
CDR/RW
DVDR/RW/R DL
R, +R DL
BD-R
001b
CD-R/RW
DVD-R/RW/R DL
Formatted DVD-RW
+R/+RW/+R DL
BD-R
Formatted DVD-RW
+RW
010b
011b
100b
101b
+R DL
+R/+R DL
+R/+R DL
BD-R
110b
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.3 FORMAT UNIT Command
The CmpLst bit is supported only in DVD-RAM media, must be set to zero with other medias.
The Interleave Value field is not supported and must be set to zero.
The Format Code field allows the value of 001b and 111b. If Format Code field is set to 001b and a BD-RE/R media is mounted,
the drive confirms for the definition of Blu-ray Disc(BD) Multi-Media Command Set Description. If Format Code field is set to
001b and a CD-RW/DVD-RW/DVD-RAM media is mounted, the drive conforms for the definition of SFFC INF-8090i. If
Format Code is set to 001b and a +RW media is mounted, the drive conform for the definition of MMC-5. If Format Code is set
to 111b and CD-RW media is mounted, the drive conforms for legacy specifications which are described in the definition of
MMC-5.
The drive supports following Format Type for each media.
Table 4 - Format Type
Support for
BD-RE
media
Support for
BD-R
media
Support for
CD-RW
media
Support for
DVD-RW
media
Support for
DVD-RAM
media
Format
Type
Support for
+RW media
Name
00h
01h
10h
Full Format
Yes
Yes
Yes
-
Yes
-
Yes
Yes
Yes
-
-
-
-
Spare Area Expansion
C/DVD-RW Full Format
DVD-RW Quick Grow the
last Border
-
-
-
-
-
-
Yes
Yes
-
13h
-
15h
26h
30h
31h
32h
DVD-RW Quick
-
-
-
-
-
-
-
-
-
-
Yes
-
-
-
-
-
DVD+RW Basic Format
Format with Spare Area
Format without Spare Area
Format BD-R with Spare Area
-
-
-
-
Yes
Yes
Yes
-
-
-
-
-
Yes
Table 5 - Format Code = 111b (CD-RW only)
Sess bit
Grow bit
Support for CD-RW media
0
0
1
1
0
1
0
1
Yes
No
No
No
The Format Unit parameter list shall be transferred from the Host to the drive. The data sent to the drive consists of a Format List
Header, followed by one Format dscriptor, so the parameter list length is always 12 bytes. When the Format Options Valid
(FOV) bit in the Format LisHeader is set to one, the DPRY, DCRT, STPF, IP, Try-out, and VS shall be set to zero. In this case,
the format operatiois performed with an Immed function specified by the Immed bit. When the FOV bit is set to zero, the
DPRY, DCRT, STPF, IP, Try-out, Immed, and VS shall be set to zero. In this case, the format operation is performed with the
drive’s internal default setting. The default setting of Immed function is one. Even if the format operation is requested with the
FOet to one, the drive’s default setting itself will not be changed.
3.1 Format Code = 001b
4.3.1.1 Format Type = 00h (Full Forma for C/DVD-RW / Default Format for BD-RE/R)
4.3.1.1.1 On DVD-RAM media
The defect list handling is specified by the combination of the CmpLst bit and the DCRT bit. In the case that the CmpLst bit is
set to zero and the DCRT bit is set to one, the Number of Blocks field shall be ignored and the number of addressable blocks
shall be retained. In other cases, the Number of Blocks field specifies the number of addressable blocks for the whole disc and
the Type Dependent Parameter field specifies the Block Length. Neither field is changeable from the values reported by READ
FORMAT CAPACITIES command.
The defect list handling is decided by the following combinations.
Table 6 – DVD-RAM Defect List Handling
PDL
G1-list
new form
Certification
CmpLst
0
DCRT
0
Certification
yes
SDL
Remarks
P-list
G2-list
preserved
disposed
disposed
slow initialization
Return to original
slipping at the latest
certification. quickly
1
1
no
preserved
preserved
disposed
disposed
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.3.1.1.2 On BD-R media
For BD-R, 4096 spare Clusters are allocated in ISA0 and 8192 Clusters in OSA. In addition, for BD-R Dual, 4096 spare Clusters
are allocated in ISA1. TDMA1 size is 2048 Clusters and TDMA2 is 4096 Clusters. For BD-R Dual, TDMA2 is 2048 Clusters,
TDMA3 is 4096 Clusters, TDMA4 is 4096 Clusters and TDMA5 is 2048 Clusters.
The drive supports the following Format Sub-type:
Table 7 - Format Sub-type
Sub-type
Description
Value
00b
01b
SRM with POW
SRM without POW
The Drive ignores the Number of Blocks field and the Block Length field.
4.3.1.2 Format Type = 30h (Format with Spare Areas for BD-RE)
The drive supports the following Format Sub-type:
Table 8 - Format Sub-type
Sub-type
Description
Value
00b
01b
Quick Reformat
No Certification
The drive formats the disc in order that the User Data Area contains at east Number of Blocks. If the number of spare Clusters to
be allocated depend on Number of Blocks is less than 4096, the command will be terminated with CHECK CONDITION status
and a SK/ASC/ASCQ values are set to ILLEGAL REQUESTINVALID FIELD IN PARAMETER LIST(05/26/00).
The Spare Area size in Clusters field is ignored by the .
4.3.1.3 Format Type = 32h (Format BD-R with Spare Areas)
Table 9 - Format Sub-type
Sub-type
Description
Value
00b
01b
SRM with POW
SRM without POW
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.4 GET CONFIGURATION Command
4.4.1 Feature List and Profile List
Supported Feature is listed to Table 10 – Feature List.
Table 10 – Feature List
Feature Number
0000h
0001h
0002h
0003h
0004h
0010h
001Dh
001Eh
001Fh
0020h
0021h
0023h
0024h
0026h
002Ah
002Bh
002Ch
002Dh
002Eh
002Fh
0033h
0038h
003Bh
0040h
0041h
0100h
0103h
0104h
0105h
0106h
0107h
0108h
010Ah
010
010
Feature Name
Profile List
Core
Morphing
Removable Medium
Write Protect
Random Readable
Multi Read
CD Read
DVD Read
Random Writable
Incremental Streaming Writable
Formattable
Hardware Defect Management
Restricted Overwrite
+RW
+R
DVD-RW Restricted Overwrite
CD-Track at Once
CD Mastering
DVD-R/-RW Write
Layer Jump Recording
BD-R POW
+R Double Layer
BD Read
BD Write
Power Management
CD Audio analog play
Microcode Upgrade
Time-out
DVD-CSS
Real-me Streaming
Logical Unit serial number
Dsc Control Block
DVD CPRM
AACS
The +RW feature and the +R feature are defined in MMC-5.
The +R Double Layer feature is defined in Double Layer +R Multi-Media Command Set.
All other features are defined in SFFC INF-8090i.
In case of BDC-203, 0038h : BD-R POW and 0041h : BD Write do not exist.
Supported Profile is listed below.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
Table 11 – Profile List
Profile Number
0002h
0008h
0009h
000Ah
0010h
0011h
0012h
0013h
0014h
0015h
0016h
001Ah
001Bh
002Bh
0040h
0041h
0042h
0043h
Profile Name
Removable Disc
CD-ROM
CD-R
CD-RW
DVD-ROM
DVD-R Sequential Recording
DVD-RAM
DVD-RW Restricted Overwrite
DVD-RW Sequential Recording
DVD-R Dual Layer Sequential Recording
DVD-R Dual Layer Jump Recording
+RW
+R
+R Double Layer
BD-ROM
BD-R SRM
BD-R RRM
BD-RE
The +RW profile and the +R profile are defined in MMC-5.
The +R Double Layer profile is defined in Double Layer +R Multi-Media Command Set.
All other profiles are defined in SFFC INF-8090i.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.4.2 Media states
The Morphing is occurred when the media or media state is changed. The drive has Media states that is described in the Table 12
Table 12 – Media states
State No
Media
No Media
CD-ROM
State
Descriptions
1
2
3-1
3-2
Not Ready
Complete
Empty
Empty Disc
No Complete Session
No Session closed Disc (Track at Once or Packet writing disc)
Session closed Disc (Session at Once writing or Session closed disc :
Appendable)
CD-R
3-3
Existing Complete Session
3-4
4-1
4-2
4-3
4-4
4-5
5
Complete
Not appendable Disc (Disc at Once writing or Finalized disc)
Empty
Empty or Blanked Disc
No Session closed Disc (Track at Once or Packet writing disc)
Session closed Disc
Not appendable Disc (Disc at Once writing or Finalized disc)
Full formatted Disc
No Complete Session
Existing Complete Session
Complete
Full Formatted
Complete
CD-RW
DVD-ROM
DVD-R
6-1
6-2
Empty
No Complete Border
Empty or Blanked Disc
No Border closed Disc
Border closed Disc
(Appendable)
6-3
Existing Complete Border
6-4
7-1
7-2
7-3
7-4
7-5
8-1
8-2
Complete
Empty
Not appendable Disc
Empty or Blanked Disc
No Border closed Disc
Border closed Disc
Full formatted Dsc
1st Border is Quick formatted
No Complete Border
Existing Complete Border
Full Formatted
Quick Formatted
Empty
DVD-RW
Empty Disc
No Complete Session
No Session closed Disc
more Session closed Disc
(Aendable)
+R
8-3
Existing Complete Sesson
8-4
9-1
9-2
9-3
10
Complete
Empty
Full Fomatted
Partialy Formatted
Complete
Not appendable Disc
Empty Disc
Full formatted Disc
Partially Formatted Disc
+RW
DVD-RAM
11-1
11-2
Empty
No Complete Session
Empty Disc
No Session closed Disc
One or more Session closed Disc
(Appendable)
Double
r
11-3
Existing Complete Session
11-4
12-1
12-2
12-3
12-4
12-5
12-6
16-1
16-2
17
Complete
Not appendable Disc
Empty
No Complete Border
Complete
No Complete Border
Existing Complete Border
Complete
Empty Disc
No Border closed Disc
Not appendable Disc
No Border closed Disc [Layer Jump Recording]
Border closed Disc (Appendable) [Layer Jump Recording]
Complete [Layer Jump Recording]
Empty (Blank) Disc
DVD-R Dual
Layer
DVD-R Dual
Layer[Layer
Jump Rec.]
Empty
Complete
BD-RE
Complete (Formatted) Disc
BD-ROM
BD-R
Complete
18-1
18-2
18-3
18-4
18-8
18-9
Empty
Empty (Blank) Disc
No Session closed Disc
One or more closed Disc (Appendable)
Not Appendable
Appendable
Not Appendable
No Complete Session
Existing Complete Session
Complete
No Complete
Complete
BD-R SRM
BD-R RRM
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.4.3 Current Profile of the Feature Header and Current bit of the Profile List
The Current Profile of the Feature Header and the Current bit of the Profile List is set as following. The Current Profile and
Current bit of Profile List is morphed by media state.
4.4.3.1 Current Profile and Current bit for No Media and CD Media
The following table indicates the Current Profile of the Feature Header and the Current bit of the Profile List that no media or
CD media is mounted.
Table 13 – Current Profile and Current bit for No Media and CD Media
Current bit of the
Profile
State Current
descriptions
No
Profile
1
2
0000h
0008h
0
1
0
0
0
0
No Profile whose current bit is set to one exists.
Only CD-ROM Profile is current to indicate the disc
is read only.
Only CD-R Profile is current to indicate the disc is
writable as a CD-R.
Only CD-R Profile is current to indicate the ds
writable as a CD-R.
3-1
3-2
0009h
0009h
0
0
1
1
0
0
CD-ROM Profile is current to indicae the dic can be
mounted as a CD-ROM.
CD-R Profile is current to indicate the disc is writable
as a CD-R.
3-3
0009h
1
1
0
Only CD-ROM Procurrent to indicate the disc
is read only.
3-4
0008h
1
0
0
4-1
4-2
000Ah
000Ah
0
0
1
1
1
1
Both CD-R Profile and CD-RW Profile are current to
indicate the disc is writable as a CD-R or a CD-RW.
CD-ROM Profile is current to indicate the disc can be
mounted as a CD-ROM.
Both CD-R Profile and CD-RW Profile are current to
indicate the disc is writable as a CD-R or a CD-RW.
CD-ROM Profile is current to indicate the disc can be
mounted as a CD-ROM.
CD-RW Profile is current to indicate the disc can be
erased or reformatted.
CD-ROM Profile is current to indicate the disc can be
mounted as a CD-ROM.
4-3
4-4
4-5
000Ah
000Ah
1
1
1
1
0
0
1
1
1
CD-RW Profile is current to indicate the disc can be
overwritten, erased or reformatted.
The other Current bits are all 0.
4.4.3.2 Current Profile and Current bit for DVD Media
The following table indicates the Current Profile of the Feature Header and the Current bit of the Profile List that DVD media is
mounted.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
Table 14 – Current Profile and Current bit for DVD Media
Current bit of the Profile
State Current
descriptions
No
Profile
DVD-ROM Profile is current to indicate the
read only.
5
0010h
0
0
0
1
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0011h
*a
0011h
*b
DVD-R Sequential Recording Profile is
current to indicate the sequential writable.
DVD-R Sequential Recording Profile is
current to indicate the sequential writable.
DVD-ROM Profile is current to indicate the
disc can be mounted as a DVD-ROM.
DVD-R Sequential Recording Profile is
current to indicate the disc is sequential
writable.
6-1
6-2
0011h
*b
6-3
0
1
1
0
0
0
0
0
Only DVD-ROM Profile is current to indicate
the disc is read only.
DVD-R/-RW Sequential Recording Profile is
current to indicate the disc is squential
writable.
DVD-RW Restricted Overwrite Profile is
current to indicate the diis fomatable.
DVD-ROM Profle is current to indicate the
disc can be mod as a DVD-ROM.
DVD-R/RW Stial Recording Profile is
curent to indicate the disc is sequential
writble.
6-4
7-1
0010h
0014h
0
0
1
0
0
1
0
0
0
1
0
1
0
0
0
0
7-2
0014h
0
0
1
0
1
1
0
0
7-3
0014h
0
1
1
0
1
1
0
0
DVDRW Restricted Overwrite Profile is
current to indicate the disc is formattable..
DVD-ROM Profile is current to indicate the
disc can be mounted as a DVD-ROM.
DVD-RW Sequential Recording Profile is
current to indicate the disc is erasable.
DVD-RW Restricted Overwrite Profile is
current to indicate the disc is overwritable.
DVD-RW Sequential Recording Profile is
current to indicate the disc is erasable.
DVD-RW Restricted Overwrite Profile is
current to indicate the disc is overwritable.
Removable disc Profile is current to indicate
the disc is Writable disk capable with
removable media.
7-4
0013h
0
1
0
0
1
1
0
0
7-5
10
0013h
0012h
0
0
0
0
1
1
0
0
1
0
0
1
0
0
0
0
DVD-RAM Profile is indicate the disc is
Random writable.
DVD-R DL Sequential Recording Profile is
current to indicate the sequential writable.
DVD-R DL Sequential Recording Profile is
current to indicate the sequential writable.
Only DVD-ROM Profile is current to indicate
the disc is read only.
DVD-R DL Layer Jump Recording Profile is
current to indicate the sequential writable.
DVD-R DL Layer Jump Recording Profile is
current to indicate the sequential writable.
Only DVD-ROM Profile is current to indicate
the disc is read only.
12-1
12-2
12-3
12-4
12-5
12-6
0015h
0015h
0010h
0016h
0016h
0010h
0
0
0
0
0
0
0
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
1
1
0
*a : If the LPP information of the disc does not applicable for the drive to execute write operations, the disc is regarded as
incompatible media and the Current Profile is set to 0000h.
*b : If the LPP information of the disc does not applicable for the drive to execute write operations, the Current Profile is set to
0010h.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
The other Current bits are all 0.
4.4.3.3 Current Profile and Current bit for +R/+RW/+R DL Media
The following table indicates the Current Profile of the Feature Header and the Current bit of the Profile List that +R/+RW/+R
DL media is mounted.
Table 15 – Current Profile and Current bit for +R/+RW/+R DL Media
Current bit of the
Profile
State Current
descriptions
No
Profile
8-1
8-2
8-3
8-4
9-1
9-2
9-3
11-1
11-2
11-3
11-4
0
0
0
0
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
001Bh
001Ah
002Bh
Only DVD+R Profile is current.
Only DVD+RW Profile is current.
Only DVD+R Double Layer Profile is
current.
4.4.3.4 Current Profile and Current bit for BD-RE/R/ROM Media
The following table indicates the Current Profile of the Featue Header and the Current bit of the Profile List that BD-RE/ROM
media is mounted.
Table 16 – Current Profile and Current bit for BD-RE/R/ROM Media
Current bit of the Profile
State Current
descriptions
No
Profile
16-1
16-2
17
18-1
18-2
18-3
18-4
18-8
18-9
0
*a
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0043h
BD-RE Profile is current.
0040h
0041h
0041h
0041h
0041h
0042h
0042h
Only BD-ROM Profile is current.
Only BD-R SRM Profile is current.
Only BD-R RRM Profile is current
*a: When the BD-RE disc with Spare areas is inserted, the Current bit of Removable Disc profile is 1.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.4.4 Current bit of the Feature List
4.4.4.1 Current bit of the Feature List for CD Media
The Current bit of the Feature List for CD media is set as Table 17 – Feature List for CD Media. The State No. is described in
Table 17 – Feature List for CD Media
State No.
1
2
3-1 3-2 3-3 3-4 4-1 4-2 4-3 4-4 4-5
Feature Name
0000h: Profile List
0001h: Core
0002h: Morphing
0003h: Removable Medium
0004h: Write Protect
0010h: Random Readable
001Dh: Multi Read
001Eh: CD Read
1
1
1
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
0
0
1
0
0
0
1
1
1
1
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
*d
0
1
0
1
1
0
0
0
1
1
1
1
0
0
1
0
0
0
1
0
0
0
0
0
0
1
1
0
0
0
0
0
0
1
0
0
1
0
1
1
0
0
0
1
1
1
1
0
1
1
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
1
1
1
1
1
0
1
1
1
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
1
1
1
1
1
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
0
0
1
0
0
0
1
1
0
1
0
0
0
1
1
0
0
0
0
0
0
1
0
0
1
0
1
1
0
0
0
1
1
1
1
0
1
1
0
0
0
1
1
0
1
1
1
1
0
1
1
1
0
0
1
1
0
1
1
1
1
0
1
1
1
0
0
0
1
0
1
1
1
1
0
1
1
1
0
0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
0
0
*a
*a
001Fh: DVD Read
0020h: Random Writable
0021h: Incremental Streaming Writable
0023h: Formattable
0024h: Hardware Defect Management
0026h: Restricted Overwrite
002Ah: DVD+RW
*b
*b
*c *c *c
0
0
0
1
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
1
002Bh: DVD+R
002Ch: Rigid Restricted Overwrite
002Dh: CD-Track at Once
002Eh: CD Mastering
002Fh: DVD-R/-RW Write
0033h: Layer Jump Recording
0038h: BD-R POW
003Bh: DVD+R Double Layer
0040h: BD Read
0041h: BD Write
0100h: Power Management
0103h: CD Audio analog play
0104h: Microcode Upgrade
0105h: Time-out
*b
*b
*d *d *d
*d *d *d
0
1
0
1
1
0
0
0
0
1
0
1
1
0
0
0
0
1
0
1
1
0
0
0
0
1
0
1
1
0
0
0
0
1
0
1
1
0
0
0
0
1
0
1
1
0
0
0
0106h: DVD-CSS
0107h: Real-Time Sreaming
0108h: Logical Unit srial number
010Ah: ontrol Block
010Bh: DCPRM
010D: AACS
*a: In write operation, if Read command or Play Audio command returns the Check Condition, the current bit is set to zero.
*b: In write operation, it keeps previous setting.
*c: This Feature indicates that Fixed Packet Writing is allowed. If only one Track is existing and the track is invisible or Fixed
Packet writing, the current bit is set to one.
*d: If Audio Track is existing, the current bit is set to one.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.4.4.2 Current bit of the Feature List for DVD Media
The Current bit of the Feature List for DVD media is set as Table 18 – Feature List for DVD-ROM/-R/-RW/RAM Media. The
Table 18 – Feature List for DVD-ROM/-R/-RW/RAM Media
1
5
6-1 6-2 6-3 6-4 7-1 7-2 7-3 7-4 7-5 10 12- 12- 12- 12- 12- 12-
State No.
1
2
3
4
5
6
Feature Name
0000h: Profile List
0001h: Core
0002h: Morphing
0003h: Removable Medium
0004h: Write Protect
0010h: Random Readable
001Dh: Multi Read
001Eh: CD Read
001Fh: DVD Read
0020h: Random Writable
0021h: Incremental Streaming Writable
0023h: Formattable
0024h: Hardware Defect Management
0026h: Restricted Overwrite
002Ah: DVD+RW
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
0
0
1
0
0
0
1
1
1
1
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
*c
1
1
0
0
*e
1
1
1
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
1
0
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
0
1
0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
0
1
1
1
1
0
1
0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
1
0
0
0
0
0
1
1
0
0
0
0
0
0
0
1
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
1
1
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
1
1
0
0
1
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
1
1
0
0
1
0
0
1
0
0
0
0
1
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
1
1
0
0
1
0
0
1
0
0
0
0
1
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
1
1
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
0
1
0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
0
1
0
0
1
0
1
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
0
1
0
0
1
0
1
0
0
0
0
0
0
0
0
1
0
0
0
0
1
0
0
1
0
1
1
0
1
1
1
1
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
*a
*a
*b
002Bh: DVD+R
002Ch: Rigid Restricted Overwrite
002Dh: CD-Track at Once
002Eh: CD Mastering
002Fh: DVD-R/-RW Write
0033h: Layer Jump Recording
0038h: BD-R POW
003Bh: DVD+R Double Layer
0040h: BD Read
0041h: BD Write
0100h: Power Management
0103h: CD Audio analog play
0104h: Microcode Upgrade
0105h: Time-out
0106h: DVD-CSS
0107h: Real-Time Stream
0108h: Logical Unit serianumber
010Ah: Disc Control Block
010Bh: DCPRM
*d *d *d *d *d *d *d *d *d *d *d *d *d *d *d *d
0
010Dh:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
*a: In write operation, if Read command returns the Check Condition, the current bit is set to zero.
*b: In write operation, it keeps previous setting.
*c: If CSS encrypted disc is existing, the current bit is set to one.
*d: If the CPRM exists on the disc the current bit is set to one, if the CPRM does not exist on the disc the current bit is set to
zero.
*e: For BD9 media, the current bit is set to one.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.4.4.3 Current bit of the Feature List for +R/+RW/+R DL Media
The Current bit of the Feature List for +R/+RW/+R DL media is set as Table 19 – Feature List for +R/+RW/+R DL Media. The
Table 19 – Feature List for +R/+RW/+R DL Media
1
8-1 8-2 8-3 8-4 9-1 9-2 9-3 11 11 11 11
-1 -2 -3 -4
State No.
Feature Name
0000h: Profile List
0001h: Core
0002h: Morphing
0003h: Removable Medium
0004h: Write Protect
0010h: Random Readable
001Dh: Multi Read
001Eh: CD Read
001Fh: DVD Read
0020h: Random Writable
0021h: Incremental Streaming Writable
0023h: Formattable
0024h: Hardware Defect Management
0026h: Restricted Overwrite
002Ah: DVD+RW
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
0
0
1
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
1
1
0
0
1
1
1
1
0
1
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
1
0
0
1
1
1
1
0
1
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
1
0
1
1
1
0
0
1
1
1
1
0
1
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
1
0
0
1
1
1
1
0
0
0
0
0
0
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
1
1
0
0
1
1
1
1
0
1
0
0
1
1
0
1
0
0
1
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
1
0
0
1
1
1
1
0
1
0
0
1
1
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
1
0
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
1
0
0
1
1
0
0
1
1
1
1
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
1
0
1
1
1
0
0
1
1
1
1
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
1
0
1
1
1
0
0
1
1
1
1
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
1
0
1
1
1
0
0
*a
*a
002Bh: DVD+R
002Ch: Rigid Restricted Overwrite
002Dh: CD-Track at Once
002Eh: CD Mastering
002Fh: DVD-R/-RW Write
0033h: Layer Jump Recording
0038h: BD-R POW
003Bh: DVD+R Double Layer
0040h: BD Read
0041h: BD Write
0100h: Power Management
0103h: CD Audio analog play
0104h: Microcode Upgrade
0105h: Time-out
0106h: DVD-CSS
0107h: Real-Time Stream
0108h: Logical Unit serianumber
010Ah: Disc Control Block
010Bh: DCPRM
010Dh:
*a: In write operation, if Read command returns the Check Condition, the current bit is set to zero.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.4.4.4 Current bit of the Feature List for BD-RE/R/ROM Media
The Current bit of the Feature List for BD-RE/R/ROM media is set asTable 20 – Feature List for BD-RE/R/ROM Media.
The State No. is described in the Table 12 – Media states.
Table 20 – Feature List for BD-RE/R/ROM Media
16 16 17 18 18 18 18
State No.
-1 -2
-1 -2 -3 -4
Feature Name
0000h: Profile List
0001h: Core
0002h: Morphing
0003h: Removable Medium
0004h: Write Protect
0010h: Random Readable
001Dh: Multi Read
001Eh: CD Read
001Fh: DVD Read
0020h: Random Writable
0021h: Incremental Streaming Writable
0023h: Formattable
0024h: Hardware Defect Management
0026h: Restricted Overwrite
002Ah:+RW
1
1
1
1
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
1
0
0
1
1
1
1
1
1
1
0
0
0
1
0
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
1
0
1
1
0
0
1
1
1
1
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
1
0
1
1
0
0
1
1
1
1
1
1
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
0
1
0
0
0
0
0
0
0
0
1
0
1
1
1
0
0
1
0
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
0
1
0
0
0
0
0
0
0
0
1
0
1
1
0
0
1
0
1
1
1
1
1
1
1
1
1
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
1
0
1
0
0
1
0
1
1
1
1
1
*a
002Bh: +R
002Ch: Rigid Restricted Overwrite
002Dh: CD-Track at Once
002Eh: CD Mastering
002Fh: DVD-R/-RW Write
0033h: Layer Jump Recording
0038h: BD-R POW
003Bh: DVD+R Double Layer
0040h: BD Read
0041h: BD Write
0100h: Power Management
0103h: CD Audio analog play
0104h: Microcode Upgrade
0105h: Time-out
*b
*c
0106h: DVD-CSS
0107h: Real-Time Streami
0108h: Logical Unit serial number
010Ah: Disc Contol Bock
010Bh: DVPRM
10Dh : A
*a: Defect Management Feature is not marked Current when no spares are allocated.
*b: BD-R POW Feature is not marked Current when the Recording mode is not SRM with LOW.
*c: BD Write Feature is not marked Current when Unknown PAC Rules are applicable or the Disc Write Protect PAC is valid.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.5 GET EVENT/STATUS NOTIFICATION Command
The drive supports polling mode only. The Immed bit must be set to one.
Following Notification Classes are supported.
Table 21 - Notification Class Request
Bit
0
Definition
Support
Reserved
-
1
2
3
4
5
6
7
Operational Change Request/Notification
Power Management
External Request
Media
Multi Host
Device Busy
yes
yes
no
yes
no
no
-
Reserved
4.5.1 Media Events
Following Media Events are supported.
Table 22 – Media Event Format
Code
Event
Description
Media status is unchanged.
0
NoChg
The drive has received a request from
the user to eject the media.
1
Eject Request
The drive has received new media, and
is ready to access it.
2
3 - 4
5
NewMedia
Reserved
A
+RW background format has
BGformatCompleted
completed.
A +RW baund format has been
automatically arted by the drive.
6
BGformatRestarted
Reserved
7 - F
4.6 GET PERFORMANCE Command
FollTyes are supported.
Table 23 – Type field values description
Type field
Definition
value
00h
01h
03h
Performance
Unusable Area (DVD-RAM, BD-RE)
Write Speed
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.6.1 Performance (Type field = 00h)
The drive has nominal only performance parameter. If Except field dose not set to 00b, the drive returns the Performance Header
only.
Table 24 – Performance Data
Write
bit
Start
LBA
Disc
Start Performance
DVD 16x CAV
16*1385*(240/585)
= 9091 (2383h)
CD 40x CAV
40*2352*75/1000*(240/585)
= 2894 (B4Eh)
End LBA
End Performance
DVD 16x CAV
No Media
0
0
0
16*1385 = 22160 (5690h)
Lead-out Start
LBA of Last
Session -1
CD 40x CAV
40*2352*75/1000
= 7056 (1B90h)
CD-ROM
CD-R
Outermost
CD 32x CAV
32*2352*75/1000*(240/585)
= 2315 (90Bh)
CD 32x CAV
32*2352*75/1000
= 5644 (160Ch)
Lead-out Start
LBA from ATIP
-1
0
0
Outermost
CD 24x CAV
24*2352*75/1000*(240/585)
= 1736 (6C8h)
CD 24x CAV
24*2352*75/1000
= 4233 (1089h)
Lead-out Start
LBA from ATIP
-1
CD-RW
DVD 16x CAV
16*1385*(240/585)
= 9091 (2383h)
DVD 16x CAV
16*1385 = 22160 (5690h)
DVD-ROM
DVD-ROM Dual
DVD-R
0
0
0
Last LBA
Last LBA
DVD 12x CAV
12*1385*(240/585)
= 6818 (1AA2h)
DVD 12x CAV
12*1385 = 16620 (40ECh)
DVD 16x CAV
16*1385*(240/585)
= 9091 (2383h)
Outermost
Lead-out Start
LBA in LPP -1
DVD 16x CAV
16*1385 = 22160 (5690h)
DVD 12x CAV
Outermost
Lead-out Start
LBA in LPP -1
DVD 12x CAV
12*1385 = 16620 (40ECh)
DVD-RW
0
0
12*1385*(240/
= 6818 1AA2h)
DVD 12CAV
12*1385*(240/585)
= 6818 (1AA2h)
Last
Possible
0
DVD 12x CAV
12*1385 = 16620 (40ECh)
DVD-R DL
Lead-out Start
LBA - 1
Last
decided
LBA,
with
DVD-RAM
0
0
Established Read Speed
Established Read Speed
FormatUnitCom
and
DVD 16x CAV
16*1385*(240/585)
= 9091 (2383h)
Outermost
Lead-out Start
LBA in ADIP -1
DVD 16x CAV
16*1385 = 22160 (5690h)
DVD 12x CAV
12*1385*(240/585)
= 6818 (1AA2h)
DVD 12x CAV
12*1385*(240/585)
= 6818 (1AA2h)
BD 8x CAV
8*4495*(240/585)
= 14752 (39A0h)
BD 8x CAV
8*4495*(240/585)
= 14752 (39A0h)
BD 8x CAV
8*4495*(240/585)
= 14752 (39A0h)
BD 6x CAV
Outermost
Lead-out Start
LBA in ADIP -1
DVD 12x CAV
12*1385 = 16620 (40ECh)
+RW
0
0
0
0
0
0
Last
Possible
DVD 12x CAV
12*1385 = 16620 (40ECh)
+R DL
Lead-out Start
LBA - 1
BD 8x CAV
8*4495
= 35960 (8C78h)
BD 8x CAV
8*4495
= 35960 (8C78h)
BD 8x CAV
8*4495
= 35960 (8C78h)
BD 6x CAV
6*4495
BD-ROM
BD-ROM Dual
BD-R/RE
BD-R/RE DL
Last LBA
Last LBA
Last
Possible
Lead-out Start
LBA - 1
Last
Possible
6*4495*(240/585)
= 11064 (2B38h)
Lead-out Start
LBA - 1
= 26970 (695Ah)
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
DVD 16x CLV
16*1385 = 22160 (5690h)
DVD 16x CLV
16*1385 = 22160 (5690h)
No Media
CD-ROM
0
0
Only the Performance Header is returned.
Outermost
Lead-out Start
LBA in ATIP -1
CD-R
CD-RW
0
Established Write Speed
Established Write Speed
DVD-ROM
Only the Performance Header is returned.
Outermost
Lead-out Start
LBA in LPP -1
DVD-R
DVD-RW
0
0
Established Write Speed
Established Write Speed
Established Write Speed
Established Write Speed
Last
Possible
DVD- R DL
DVD-RAM
Lead-out Start
LBA – 1
Last
decided
FormatUnitCom
and
LBA,
with
1
0
Established Write Speed
Established Write Speed
Outermost
Lead-out Start
LBA in ADIP -1
+R
+RW
0
0
Established Write Speed
Established Write Speed
Established Write Speed
Estblished Write Speed
Last
Possible
+R DL
Lead-out Start
LBA – 1
BD-ROM
BD-R/RE
BD-R/RE DL
Only the Performance Header is returned.
Outermost
0
0
Established Write Speed
Established Wred
Lead-out Start
LBA in ADIP -1
Outermost
Lead-out Start
LBA in ADIP -1
Established Write Speed
Established Write Speed
Notes: About the Last Possible Lead-out Start LBA of +R DL media, refer the Notes of Table 26 – Write Speed Data for DVD
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.6.2 Write Speed (Type field = 03h)
4.6.2.1 Write Speed Data for No Media and CD Media
Table 25 – Write Speed Data for No Media and CD Media
Write Speed
Descriptor #
Disc
End LBA
Read Speed
Write Speed
DVD 16x CLV
DVD 16x CLV
16*1385 = 22160 (5690h)
#1
16*1385 = 22160 (5690h)
DVD 12x CLV
12*1385 = 16620 (40ECh)
DVD 12x CLV
12*1385 = 16620 (40ECh)
#2
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 8x CLV
8*1385 = 11080 (2B48h)
#3
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 6x CLV
6*1385 = 8310 (2076h)
#4
DVD 5x CLV
5*1385 = 6925 (1B0Dh)
DVD 4x CLV
DVD 5x CLV
5*1385 = 6925 (1B0Dh)
DVD 4x CLV
#5
No Media
23127Fh
#6
4*1385 = 5540 (15A4h)
4*1385 = 5540 (15A4h)
DVD 3.3x CLV
3.3*1385 = 4570 (11DAh)
DVD 3x CLV
DVD 3.3x CLV
3.3*1385 = 4570 (11DAh)
DVD 3x CLV
#7
#8
3*1385 = 4155 (103Bh)
3*1385 = 4155 (103Bh)
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 1x CLV
DVD 24x CLV
2.4*1385 = 3324 (CFCh)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 1x CLV
#9
#10
#11
1*1385 = 1385 (569h)
CD 32x CLV
1*1385 = 1385 (569h)
CD 32x CLV
#1
#2
#3
32*2352*75/100
(160Ch)
D 2x CLV
*2352*75/1000
(108Ah)
CD 16x CLV
16*2352*75/1000
(B07h)
CD 10x CLV
10*2352*75/1000
(6E4h)
CD 4x CLV
4*2352*75/1000 = 706 (2C2h)
CD 32x CLV
32*2352*75/1000
(160Ch)
CD 24x CLV
24*2352*75/1000
(108Ah)
CD 16x CLV
16*2352*75/1000
(B07h)
CD 10x CLV
10*2352*75/1000
(6E4h)
CD 4x CLV
4*2352*75/1000 = 706 (2C2h)
CD 24x CLV
24*2352*75/1000
(108Ah)
=
=
=
=
5644
4234
2823
1764
32*2352*75/1000
(160Ch)
CD 24x CLV
24*2352*75/1000
(108Ah)
CD 16x CLV
16*2352*75/1000
(B07h)
CD 10x CLV
10*2352*75/1000
(6E4h)
CD 4x CLV
4*2352*75/1000 = 706 (2C2h)
CD 32x CLV
32*2352*75/1000
(160Ch)
CD 24x CLV
24*2352*75/1000
(108Ah)
CD 16x CLV
16*2352*75/1000
(B07h)
CD 10x CLV
10*2352*75/1000
(6E4h)
CD 4x CLV
4*2352*75/1000 = 706 (2C2h)
CD 24x CLV
24*2352*75/1000
(108Ah)
=
=
=
=
5644
4234
2823
1764
Lead-out Start LBA
oLast Session -1
CD-ROM
#4
#5
#1
Outermost Lead-out
Start LBA from
ATIP -1
=
=
=
=
5644
4234
2823
1764
=
=
=
=
5644
4234
2823
1764
#2
#3
CD-R
#4
#5
#1
CD-RW
(Ultra Speed+)
=
=
4234
2823
=
=
4234
2823
CD 16x CLV
16*2352*75/1000
(B07h)
CD 16x CLV
16*2352*75/1000
(B07h)
#2
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
CD 10x CLV
10*2352*75/1000
(6E4h)
CD 24x CLV
24*2352*75/1000
(108Ah)
CD 16x CLV
16*2352*75/1000
(B07h)
CD 10x CLV
10*2352*75/1000
(6E4h)
CD 10x CLV
10*2352*75/1000
(6E4h)
CD 24x CLV
24*2352*75/1000
(108Ah)
CD 16x CLV
16*2352*75/1000
(B07h)
CD 10x CLV
10*2352*75/1000
(6E4h)
CD 10x CLV
10*2352*75/1000
(6E4h)
#3
#1
#2
#3
#1
=
=
=
=
=
1764
4234
2823
1764
1764
=
=
=
=
=
1764
4234
2823
1764
1764
CD-RW
(Ultra Speed)
CD 10x CLV
10*2352*75/1000
(6E4h)
CD-RW
(High Speed)
CD 4x CLV
4*2352*75/1000 = 706 (2C2h)
CD 4x CLV
4*2352*75/1000 = 706 (2C2h)
CD 4x CLV
4*2352*75/1000 = 706 (2C2h)
CD 4x CLV
4*2352*75/1000 = 706 (2C2h)
#2
#1
CD-RW
(1x – 4x)
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.6.2.2 Write Speed Data for DVD Media
Table 26 – Write Speed Data for DVD Media
Write Speed
Descriptor #
Disc
End LBA
Read Speed
DVD 16x CLV
Write Speed
DVD 16x CLV
#1
16*1385 = 22160 (5690h)
16*1385 = 22160 (5690h)
DVD 12x CLV
12*1385 = 16620 (40ECh)
DVD 12x CLV
12*1385 = 16620 (40ECh)
#2
#3
#4
#5
#6
#7
#8
#9
#10
#11
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 5 CLV
5*1385 = 6925 (1B0Dh)
DVD 5x CLV
5*1385 = 6925 (1B0Dh)
DVD 4 CLV
4*1385 = 5540 (15A4h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD-ROM
Last LBA
DVD 3.3x CLV
3.3*1385 = 4570 (11DAh)
DVD 3.3x CLV
3.3*1385 = 4570 (11DAh)
DVD 3x CLV
3*1385 = 4155 (103Bh)
DVD 3x CLV
3*1385 = 4155 (103B
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 1x CLV
1*1385 = 1385 (56
DVD 1x CLV
1*1385 = 1385 (569h)
DVD 1x CAV
16*1385 = 22160 (5690h)
DVD 12x P-CAV
12*1385 = 16620 (40ECh)
DVD 8x P-CAV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 12x CLV
12*1385 = 16620 (40ECh)
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 1x CLV
1*1385 = 1385 (569h)
DVD 1x CLV
1*1385 = 1385 (569h)
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 16x CAV
16*1385 = 22160 (5690h)
DVD 12x P-CAV
12*1385 = 16620 (40ECh)
DVD 8x P-CAV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 12x CLV
12*1385 = 16620 (40ECh)
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 1x CLV
1*1385 = 1385 (569h)
DVD 1x CLV
1*1385 = 1385 (569h)
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
#1
#2
#3
#4
#5
#1
#2
#3
#4
#1
#2
#3
#1
#1
#2
#3
#4
DVD-R (16x)
CAV Writing
Outermost
Start LBA in LPP - 1
Lead-out
DVD-R (16x)
Z-CLV g
DVD-R (8x)
DVD-R (4x)
DVD-R (1x)
Last Possible Lead-out
Start LBA -1
DVD-R DL(8x)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 2x CLV
2*1385 = 2770 (AD2h)
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 1x CLV
1*1385 = 1385 (569h)
DVD 1x CLV
1*1385 = 1385 (569h)
DVD 5x CLV
5*1385 = 6925 (1B0Dh)
DVD 3x CLV
3*1385 = 4155 (103Bh)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 3x CLV
3*1385 = 4155 (103Bh)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 2x CLV
2*1385 = 2770 (AD2
DVD 16x CAV
16*1385 = 22160 (50h)
DVD 12x P-CAV
12*1385 16620 (40ECh)
DVD 8x P-CAV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 12x CLV
12*1385 = 16620 (40ECh)
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 1x CLV
1*1385 = 1385 (569h)
DVD 1x CLV
1*1385 = 1385 (569h)
DVD 5x CLV
5*1385 = 6925 (1B0Dh)
DVD 3x CLV
3*1385 = 4155 (103Bh)
DVD 2x CLV
2*1385 = 2770 (AD2h
DVD 3x CLV
3*1385 = 4155 (103Bh)
DVD 2x CLV
*1385 = 2770 (AD2h)
DVD 2x CLV
2*1385 = 2770 (AD2h)
DVD 16x CAV
16*1385 = 22160 (5690h)
DVD 12x P-CAV
12*1385 = 16620 (40ECh)
DVD 8x P-CAV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 12x CLV
12*1385 = 16620 (40ECh)
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 6x CLV
6*1385 = 8310 (2076h)
DVD 4x CLV
#1
#2
#3
#1
#2
#1
#2
#1
#1
#2
#3
#1
#2
#1
#1
#2
#3
#4
#5
#1
#2
#3
#4
#1
#2
#1
#1
#2
#3
#4
#1
#2
DVD-RW (6x)
DVD-RW (4x)
Outermost
Start LBA in LPP - 1
Lead-out
DVD-RW (2x)
DVD-RW (1x)
DVD-RAM (5x)
Last LBA, decided
with
FormatUnitComand
DVD-RAM (3x)
DVD-RAM (2x)
+R (16x)
CAV Writing
(Z-CLV
Writing)
Outermost
Start LBA in ADIP - 1
Lead-out
+R (16x)
Z-CLV Writing
+R (8x)
+R (4x)
+R (2.4x)
Last Possible Lead-out
Start LBA -1
+R DL(8x)
+RW (8x)
4*1385 = 5540 (15A4h)
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 6x CLV
4*1385 = 5540 (15A4h)
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
DVD 8x CLV
8*1385 = 11080 (2B48h)
DVD 6x CLV
Outermost
Start LBA in ADIP - 1
Lead-out
6*1385 = 8310 (2076h)
6*1385 = 8310 (2076h)
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
DVD 3.3x CLV
3.3*1385 = 4570 (11DAh)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
DVD 3.3x CLV
3.3*1385 = 4570 (11DAh)
DVD 4x CLV
4*1385 = 5540 (15A4h)
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
DVD 2.4x CLV
2.4*1385 = 3324 (CFCh)
#3
#1
#2
#1
+RW (4x)
+RW (2.4x)
Notes : For +R DL media, the Last Possible Lead-out Start LBA is set as follows.
1) In case of the disc which has no complete status, it is set to the following value.
The value = ( L0 Data Zone Capacity + 1 – 30000h ) x 2 – Extended Partial Lead-out Size
As for the L0 Data Zone Capacity,
if it has not been changed from the default value, it is set to the Last Possible Physical Sector of the Data Zone on Layer 0 in
ADIP,
and if it has been changed from the default value, it is set to the Actual last PSN of Data Zone on Layer 0 in TOC.
As for the Extended Partial Lead-out Size,
if the disc has an Extended Partial Lead-out, it is 30000h,
and if the disc has no Extended Partial Lead-out, it is 0.
2) In case of the disc which has a complete status, it is set to the Actual Lead-out Start LBA.
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.6.2.3 Write Speed Data for BD Media
Table 27 – Write Speed Data for BD Media
Write Speed
Descriptor #
Disc
End LBA
Read Speed
BD 8x CLV
Write Speed
BD 8x CLV
#1
8*4495 = 35960 (8C78h)
8*4495 = 35960 (8C78h)
BD 6x CLV
6*4495 = 26970 (695Ah)
BD 6x CLV
6*4495 = 26970 (695Ah)
#2
#3
#4
#1
BD-R SL/DL
Z-CLV Writing
BD 4x CLV
4*4495 = 17980 (463Ch)
BD 4x CLV
4*4495 = 17980 (463Ch)
Outermost
Start LBA in ADIP - 1
Lead-out
BD 2x CLV
2*4495 = 8990 (231Eh)
BD 2x CLV
2*4495 = 8990 (231Eh)
BD 2x CLV
2*4495 = 8990 (231Eh)
BD 2x CLV
2*4495 = 8990 (231Eh)
BD-RE SL/DL
4.7 INQUIRY Command
CmdDt bit, EVPD bit and Page Code or Operation Code field does not supported. These bit or field must be set to 0.
The drive returns following 96bytes Inquiry data.
Table 28 - INQUIRY Data Format
Bit
7
6
5
4
3
2
1
0
Byte
0
1
2
3
4
5
6
7
8
Reserved
Peripheral Device Type (05h)
Reserved
RMB (1)
ISO Version (0h)
ECMsion (0h)
ANSI Version (0h)
Response Data Format(2h)
ATAPI Transport Versin(3h)
Additional Length (5Bh)
Reserved
Reserved
Reserved
Vendor Identification = “PIONEER “
15
16
31
32
35
36
37
46
47
55
56
95
Product Identification = ” BD-RW
BDR-203“
Product Revision Level = “X.XX”
Reserved
Release Date = “YY/MM/DD”
Manufacture’s Information
Reserved
4.8 LOG SELECT Command
This command is used for checking the drive.
The specifications of this command are vendor unique.
4.9 LOG SENSE Command
This command is used for checking the drive.
The specifications of this command are vendor unique.
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.10 MECHANISM STATUS Command
Mechanism Status Parameter List:
Fault bit, Current Slot field, C/DVD Mechanism State field, Number of Slots Available field and Length of Slot Table(s) field
are set to zero.
4.11 MODE SELECT (10) Command
The Save Page function is not supported. The SP bit must be set to zero.
Refer the MODE SENSE Command for the descriptions of each page.
4.12 MODE SENSE (10) Command
4.12.1 Mode Parameter Header
Table 29 - Mode Parameter Header
Bit
7
6
5
4
3
2
1
0
Byte
0
1
2
3
4
5
6
7
(MSB)
Mode Data Length
Medium Type
(LSB)
Reserved
(MSB)
Block Descriptor Length (always
(LSB)
Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
The Medium Type was defined in a legacy specification, and remains in this drive.
The Medium Type Codes are defined as shown in Table 30 – Medium Type Codes.
Table 30 – Medium Type Codes
Page code
00h
Description
Door closed, medium type unknown or BD
01h
02h
03h
04h
05h
06h
07h
08h
120 mm CD-ROM data only, door closed
120 mm CD-ROM audio only (CD-DA), door closed
120 mm CD-ROM data and audio combined, door closed
120 mm multi-session CD-ROM or CD-I, door closed
80 mm CD-ROM data only, door closed
80 mm CD-ROM audio only (CD-DA), door closed
80 mm CD-ROM data and audio combined, door closed
80 mm multi-session CD-ROM or CD-I, door closed
Reserved
120 mm CD-R data only, door closed
120 mm CD-R audio only, door closed
120 mm CD-R data and audio combined, door closed
120 mm multi-session CD-R, door closed
80 mm CD-R data only, door closed
80 mm CD-R audio only, door closed
80 mm CD-R data and audio combined, door closed
80 mm multi-session CD-R, door closed
Reserved
120 mm CD-RW data only, door closed
120 mm CD-RW audio only, door closed
120 mm CD-RW data and audio combined, door closed
120 mm multi-session CD-RW, door closed
80 mm CD-RW data only, door closed
80 mm CD-RW audio only, door closed
80 mm CD-RW data and audio combined, door closed
80 mm multi-session CD-RW, door closed
Reserved
09h – 10h
11h
12h
13h
14h
15h
16h
17h
18h
19h – 20h
21h
22h
23h
24h
25h
26h
27h
28h
29h – 40h
41h
120 mm single border/session DVD/-R/-RW/RAM/+R/+RW, door closed
Reserved
42h
43h
Reserved
44h
45h
46h
120 mm multi border/session DVD-R/-RW/+R, door closed
80 mm single border/session DVD-ROM/-R/-RW/RAM/+R/+RW, door closed
Reserved
47h
Rerved
48h
47h
80 mm multi border/session DVD-R/-RW/+R, door closed
Reserved
48
49h –
70h
80 mm multi border/session DVD-R/-RW/+R, door closed
Reserved
Door closed, no disc present
71h
Door open
72h
73h – FFh
Door closed, incompatible medium exists
Reserved
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.12.2 Mode Pages
The drive is not supported the Parameters Savable (PS) bit and must be set to zero.
The Page Code field identifies the format and parameters defined for that mode page.
The drive supports following Mode pages.
Table 31 - Mode Page Codes
Page code
01h
Description
Section
Error Recovery Page
Write Parameters Page
Caching Page
4.12.2.2 on page 31
4.12.2.5 on page 32
4.12.2.1 on page 31
See SFFC INF-8090i document
4.12.2.3 on page 31
4.12.2.4 on page 31
4.12.2.6 on page 33
05h
08h
0Eh
1Ah
1Dh
2Ah
3Fh
CD Audio Control Page
Power Condition Page
Time-out & Protect Page
Capabilities & Mechanical Status Page
Return all pages (valid only for the MODE SENSE command)
4.12.2.1 Caching Page
The Caching Page is supported for compatibility of other CD-R/RW drive. This page has no effect on write/read operation. The
returned Caching parameters by the MODE SENSE (10) Command are modified to the new parameters after receivg new
parameters by MODE SENSE (10) Command.
Table 32 - Caching Parameter
7
6
5
4
3
2
1
0
Bit
Byte
0
1
2
3
4
5
6
7
8
9
PS
Reserved
ABPF
Page C08h
Page Length = 0Ah
DISC SIZE
IC
CAP
WCE
MF
RCD
Demand Read Priority
Write Retention Priority
(MSB)
(MSB)
(MSB)
(MSB)
Disable Prefetch Transfer Length
Minimum Pre-fetch
(LSB)
(LSB)
(LSB)
(LSB)
Maximum Pre-fetch
10
11
Maximum Pre-fetch Ceiling
Default value of the WCE bit is one. Default value of any other bits and field is zero.
4.12.2.2 Error Recovery Parameters Page
The E and ARRE bits are not supported and are ignored.
The TB, RC, DTE and DCR bits are ignored.
The PER bit and EMCDR field are used to control the defect reporting.
Setting value of the Read Retry Count and the Write Retry Count field are ignored.
4.12.2.3 Power Condition Page
The default value of an Idle bit is one. The default value of the Idle Timer field is 000000c8h (20 second).
The default value of the Standby bit is one. The default value of Standby Timer field is 000012C0h (8 minutes).
4.12.2.4 Time-out & Protect Page
The DISP, SWPP bits are not supported and must be set to 0.
Page 32
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.12.2.5 Write Parameters Mode Page
The parameters specified in the Write Parameters Mode Page are not applicable to DVD-RAM media.
The parameters specified in the Write Parameters Mode Page are not applicable to +R/+RW/+R DL media.
The parameters specified in the Write Parameters Mode Page are not applicable to formatted DVD-RW media.
The parameters specified in the Write Parameters Mode Page are not applicable to BD-RE/R media.
The default value of the BUFE bit is 1. The drive ignores this bit and assumes this bit is set to 1.
If LS_V bit is set to one, the Link Size field must be set to 7h for CD-R/RW or 10h for DVD-R/-RW. If LS_V bit is set to zero,
the drive assumes the Link Size of 7h for CD-R/RW or 10h for DVD-R/-RW. The default value of the LS_V bit is 1, and the
default value of the Link Size field is 10h.
The drive supports following Write Type.
Table 33 - Write Type Field
for CD-R/RW
for DVD-R/-RW
for DVD-R DL
Value
Definition
Support Test Write Support Test Write Support Test Write
00h
01h
02h
03h
04h
Packet/Incremental
Track-at-once
Session-at-once/Disc-at-once
Raw
yes
yes
yes
yes
-
yes
yes
yes
-
yes
yes
yes
-
yes
-
yes
-
yes
-
-
yes
-
-
yes
-
Layer Jump Recording
-
-
-
yes
yes
If the Layer Jump Recording has not been supported, Layer Jump Recording (04h) is not supported.
The default value of the Test Write bit is 0, and the default value of the Write Type field is 0h.
When FP bit is set to one for CD-R/RW media, the Packet Size field must be set to 32. Because the drive supports 64K Fixed
Packet Writing only. The default value of the FP bit is 0.
The Copy bit is not supported, and setting of this bit is ignored.
The drive supports following Data Block Type for CD-R/RW media.
Table 34 – Data Block Type Field
Value
0
1
2
3
8
9
10
11
12
1
Block Size
2352
Definiti
Support for CD-R/RW
Raw data
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
2368
2448
2448
2048
2336
2048
2056
2324
Raw data with P and Q sub-channel
Raw data with P-W sub-channel appended
Raw a with raw P-W sub-channel appended
Mode 1 (ISO/IEC 10149)
Mode 2 (ISO/IEC 10149)
Mode 2 (CD-ROM XA, form 1)
Mode 2 (CD-ROM XA, form 1)
Mode 2 (CD-ROM XA, form 2)
Mode 2 (CD-ROM XA, form 1, form 2, or mixed form)
2332
The drive supports writing of DVD and CD. Each media needs different value of Link Size field in Write Parameters page.
Current value of parameter can not change by mounted media automatically. But Default value of Link Size field is changed by
mounted media. If DVD media is mounted, Link Size field of default value in Write Parameter page is set to 10h. If CD media is
mounted, it is set to 07h. It recommends following step to setting the Write Parameters page.
1. Get default value of Write Parameters by using MODE SELECT command. ( Page Control (PC) field = 10b)
2. Modify the necessary field on above parameter.
3. Send the modified parameter by using MODE SELECT command.
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.12.2.6 C/DVD Capabilities and Mechanical Status Page
The C/DVD Capabilities and Mechanical Status Page format is defined as shown in Table 35 - C/DVD Capabilities and
Table 35 - C/DVD Capabilities and Mechanical Status Page Format
Bit
7
6
5
4
3
2
1
0
Byte
0
1
PS
Reserved
Page Code = 2Ah
Page Length = 42h
DVD-R/-R DVD-RO
DVD-RA
M Read
1
DVD-RA
M Write
1
Mode2
Form2
1
CD-RW
Read
1
CD-R
Read
1
Reserved
Method 2
1
ead
M Read
2
3
4
00b
Reserved
00b
1
1
DVD-R
Write
1
CD-RW
Write
1
CD-R
Write
1
Reserved
Test Write
0
1
Multi-sessi
Mode2
Form1
1
Digital
Port(2)
0
Digital
Port(1)
0
BUF
Composite
Audio Ply
1
on
1
1
0
Read Bar
Code
Capable
C2
CDDA
Stream
Accurate
1
R-W
Supported
UPC
ISRC
1
Pointers
Supported
0
R-W D&C
CDA
5
6
0
1
0
0
1
Prevent
Jum
LMT
Reserved
0
Eject
Lock State
Lock
current
state
001b
1
0
1
upports
Disc
Present
(SDP)
0
R-W in
Lead-in
Readable
Side
Change
Capable
S/W Slot
Selection
SSS)
Separate
Channel
Mute
Reserved
00b
Sep. vol.
7
1
0
0
1
1
8
9
(MSB)
(MSB)
(MSB)
(MSB)
Mm Read Speed Supported
(LSB)
(LSB)
(LSB)
(LSB)
10
11
12
13
14
15
16
Number of Volume Levels Supported = 0100h
Buffer Size supported by Logical Unit = 0FA0h
Current Read Speed
Reserved = 00h
Reserved
00b
Length
00b
LSBF
0
RCK
0
BCKF
0
Reserved
0
17
8
1
20
21
22
23
24
25
26
(MSB)
Maximum Write Speed Supported
Current Write Speed
(LSB)
(LSB)
(LSB)
(MSB)
(MSB)
Copy Management Revision Supported = 0001h
Reserved = 00h
Reserved = 00h
Reserved = 00h
Reserved
Rotation Control Selected
00b
27
000000b
28
29
30
31
32
(MSB)
(MSB)
Current Write Speed Selected
(LSB)
Number of Logical Unit Write Speed Performance Descriptor Tables
(LSB)
Reserved = 00h
Reserved
000000b
Rotation Control #1
00b
33
34
35
(MSB)
Write Speed Supported #1
(LSB)
36 – 63
Logical Unit Write Speed Performance Descriptors #2 - #8
Page 34
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
Bit
7
6
5
4
3
2
1
0
Byte
64
Reserved = 00h
Reserved
000000b
Rotation Control #8
00b
65
66
67
(MSB)
Write Speed Supported #9
(LSB)
The Maximum Read Speed Supported field does not reflect the maximum read speed for each medium type and format. If no
disc is mounted in the drive, the field is set to the same value as DVD.
The Current Read Speed filed does not reflect the actual read speed. If no disc is mounted in the drive, the field is set to the same
value as DVD.
The Maximum Write Speed Supported field is set to the same value of the Write Speed Descriptor #1 data which is returned for
the GET PERFORMANCE command.
The Current Write Speed filed is set to the same value of the Write Performance data which is returned for the GET
PERFORMANCE command.
The Number of Logical Unit Write Speed Performance Descriptor Tables and The Logical Unit Write Speed Performance
Descriptors #1 - #8 are set to the suitable values by using the same algorism as the GET PERFORMANCE command.
4.13 PLAY CD Command
This command is defined in a legacy specification (MMC-2 Revision 10a).
4.14 READ (10), READ (12) Command
The RelAdr bit is not supported and must set to 0.
If the Streaming bit in the CDB of the READ (12) command is set to one, the Fit shall be set to zero. The setting of the
Streaming bit is no effect on the operation.
4.15 READ BUFFER Command
This command is used for checking the drive.
The specifications of this command are vendr uniqu
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.16 READ BUFFER CAPACITY Command
The Block bit is supported.
The Length of Buffer field in the READ BUFFER CAPACITY data is set to following.
BD or no medium : 180000h
DVD : 118000h
CD : 126800h
4.17 READ CAPACITY Command
The RelAdr bit is not supported and must set to 0.
If empty disc is mounted, the Logical Block Address field in the Read Capacity Data is set to zero.
If a non-blank +RW disc is mounted, the Logical Block Address field in the Read Capacity Data is set to 23053Fh.
If a disc that is not a +RW and has no Complete Session is mounted, Logical Block Address field in the Read Capacity Data is
set to zero.
When a CD-R/RW disc is mounted, if it is recorded by Track-at-once, the Logical Block Address field in the Read Capacity Data
is set to the LBA immediately behind of the outermost Lead-out, so 2 Run-out blocks will be encountered.
4.18 READ DISC INFORMATION Command
For +R/+R DL media, the Last Session Lead-in Start Address is the LBA of where the next Intro shall brecoded. If no session
exists on the disc, then the value returned is 00000000h. If the disc has complete status, then the value returned is FFFFFFFFh.
For +R media, the Last Possible Lead-out Start Address is the LBA found in the ADIP of the discs lead-in. If the disc has
complete status, then the value returned is FFFFFFFFh.
For +R DL media, the Last Possible Lead-out Start Address is set as follows.
1) In case of a disc that has no complete status, it is set to the following value.
The value = ( L0 Data Zone Capacity + 1 – 30000h ) x 2 – Extended Partial Lead-out Size
As for the L0 Data Zone Capacity,
if it has not been changed from the default value, it is set to he Last Possible Physical Sector of the Data Zone on Layer 0 in
ADIP,
and if it has been changed from the default vaue, it is sthe Actual last PSN of Data Zone on Layer 0 in TOC.
As for the Extended Partial Lead-out Size,
if the disc has an Extended Partial Lead-out, it is 30000h,
and if the disc has no Extended Partal Lead-out, it is 0.
2) In case of a disc that has complete status, it is set to FFFFFFFFh.
The OPC table is nosupported for +R/+RW/+R DL media.
Page 36
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.19 REQUEST SENSE Command
The drive returns the 22 bytes of Sense Data.
When Sense Key, Additional Sense Code and Additional Sense Code Qualifier field is set to 2/3A/00 MEDIUM NOT PRESENT
or 2/04/01 LOGICAL UNIT IS IN PROCESS OF BECOMING READY, the Loading information is set to Byte 21 in the Sense
Data as following.
Table 36 – Loading Status
Byte 21
00h
Loading Status
Tray Open
01h
Loading
02h
Unloading
03h
04h
Tray Close and no media
Reserved
05h
Tray Close and Setup
4.20 SET CD SPEED Command
The drive can not specify the reading speed by any Packet command. The setting of Logical Unit Read Speed field is ignored.
The reading speed is determined by the drive.
This command changes the writing speed for CD-R/RW media. It does not effect to the writing speed for DVD-R/-RRAM ,
+R/+RW/+R DL and BD-R/RE media.
The available writing speed may be restricted by the drive when the characteristic of media is not suitable for the speed.
Table 37 – Parameters to set Writing speed for CD-R/RW
Logical Unit
Writing Speed
CD-R Writing
Speed
CD-RW Writing
Speed
DVD-R/-RW an+RW
Writing Spe
BD-R/RE
Writing Speed
0000h – 06E2h
06E3h – 0B05h
0B06h – 1088h
4x CLV
10x CLV
16x ZCLV
4x CLV
10x CLV
16x CLV
Remains previous setting
Remains previous setting
1089h – 160Bh
160Ch – FFFFh
24x ZCLV
32x ZCLV
24x ZC
2x ZCL
4.21 SET STREAMING Comand
4.21.1 Reading Spee
The Drive can not specify the reading speed by any Packet command.
The rding speed may be automatically reduced by the drive in order to retry to read a block which has not been corrected
erro
Table 38 – Available Reading speed for each media
Media
CD-DA/R/RW (play audio)
CD-ROM/R/RW (read mode2form2)
CD-DA/ROM (other operations)
CD-R (other operations)
CD-RW (other operation)
DVD-ROM Single Layer
DVD-ROM Dual Layer
DVD-R
DVD-R DL
DVD-RW
DVD-RAM
+R
Reading Speed
9.3x CAV - 4x CLV
9.3x CAV - 4x CLV
40x CAV – 4x CLV
32x CAV – 4x CLV
24x CAV – 4x CLV
16x CAV – 1x CLV
12x CAV - 1x CLV
16x CAV – 1x CLV
12x CAV – 1x CLV
12x CAV – 1x CLV
5x ZCLV – 2x CLV
16x CAV – 2.4x CLV
12x CAV – 2.4x CLV
12x CAV – 2.4x CLV
8x CAV – 2x CLV
6x CAV - 2x CLV
+R DL
+RW
BD-ROM SL/DL、BD-R/RE SL
BD-R/RE DL
After writing, the reading speed is change to same speed of writing speed.
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
4.21.2 Writing Speed
The drive can specify the following writing speed. Default value of writing speed is maximum speed for each media type.
In this drive, the established values are always reset to the default values after loading media.
The available writing speed may be restricted by the drive when the characteristic of media is not suitable for the speed.
Table 39 – Available Writing speed for each media
Media
Available Writing Speed
32x ZCLV, 24x ZCLV, 16x ZCLV, 10x CLV, 4x CLV
4x CLV
CD-R
CD-RW (1 - 4x)
CD-RW High Speed
CD-RW Ultra Speed
CD-RW Ultra Speed+
DVD-R (1x)
10x CLV, 4x CLV
24x ZCLV, 16x ZCLV, 10x CLV, 4x CLV
24x ZCLV, 16x ZCLV, 10x CLV, 4x CLV
1x CLV
DVD-R (1 - 4x)
DVD-R (1 - 16x)
DVD-R DL (2 -8x)
DVD-RW (1x)
4x ZCLV, 2x CLV, 1x CLV
16x CAV, 12x ZCLV, 8x ZCLV, 6x ZCLV, 4x ZCLV
8xZCLV, 6xZCLV, 4x ZCLV, 2x CLV
1x CLV
DVD-RW (1 - 2x)
DVD-RW (2 - 4x)
DVD-RW (2 - 6x)
DVD-RAM (2x)
DVD-RAM (2 – 3x)
DVD-RAM (2 – 5x)
+R (1 - 2.4x)
2x CLV, 1x CLV
4x ZCLV, 2x CLV
6x ZCLV,4x ZCLV, 2x CLV
2x CLV
3x CLV, 2x LCV
5x ZCLV, 3x CLV, 2x CLV
2.4x CLV
+R (1 - 4x)
4x ZCLV, 2.4x CLV
+R (1 – 16x)
+R DL (2 -8x)
+RW (1 - 2.4x)
+RW (1 – 4x)
16x CAV, 12x ZCLV, 8x ZCLV, 6x ZCLV, 4x ZCLV
8x ZCLV,6x ZCLV, 4x ZCLV, 2.4x CLV
2.4x CLV
4x ZCLV, 2.4x CLV
+RW (3.3x – 8x)
BD-R SL/DL
BD-RE SL/DL
8x ZCLV ,6x ZCLV , 3.3x CLV
8x ZCLV, 6x ZCLV, 4x ZCLV, V
2x CLV
The setting of the RDD, Exact and MRW bits and the Start LBA, End LBA, Read Size and Read Time fields are ignored. The
specified writing speed will apply to whole disc area.
It is recommended to use the llowing values in order to set the write speed;
Table 40 – Parameters to set Writing speed for CD-R/RW media
CD-R Writing
Speed
32x ZCLV
4x CLV
10x CLV
16x ZCLV
24x ZCLV
32x ZCLV
CD-RW Writing
Speed
Write time
0000
Write Size
0001h – FFFFh
0000h – 06E3h
06E4h – 0B06h
0B07h – 1089h
108Ah – 160Ch
160Dh – FFFFh
24x ZCLV
4x CLV
10x CLV
16x ZCLV
03E8h
24x ZCLV
Table 41 – Parameters to set Writing speed for DVD-R/RW/R DL media
DVD-R
Writing Speed
16x CAV
1x CLV
DVD-R DL
Writing Speed
8x ZCLV
1x CLV
DVD-RW
Writing Speed
6x ZCLV
1x CLV
Write time
0000h
Write Size
0001h – FFFFh
0000h – 0AD1h
0AD2h – 15A3h
15A4h – 2075h
2076h – 2B47h
2B48h – 40EBh
40ECh – 568Fh
5690h – FFFFh
2x CLV
4x CLV
2x CLV
4x CLV
6x CLV
2x CLV
4x CLV
03E8h
6x CLV
8x ZCLV
12x ZCLV
16x CAV
6x CLV
8x ZCLV
Page 38
Download from Www.Somanuals.com. All Manuals Search And Download.
BDR-203/BDC-203 Command Reference Manual Version 0.90
Table 42 – Parameters to set Writing speed for +R/+RW/+R DL media
+R
+R DL
Writing Speed
8x ZCLV
2.4x CLV
4x CLV
+RW
Writing Speed
8x ZCLV
2.4x CLV
4x CLV
Write time
0000h
Write Size
Writing Speed
0001h – FFFFh
0000h – 15A3h
15A4h – 2075h
2076h – 2B47h
16x CAV
2.4x CLV
4x CLV
6x CLV
6x CLV
6x CLV
03E8h
2B48h – 40EBh
40ECh – 568Fh
5690h – FFFFh
8x ZCLV
12x ZCLV
16x CAV
8x ZCLV
8x ZCLV
Table 43 – Parameters to set Writing speed for BD-R/RE media
BD-R
Writing Speed
8x ZCLV
2x CLV
4x CLV
BD-RE
Writing Speed
Write time
0000h
Write Size
0001h – FFFFh
0000h – 463Bh
463Ch – 6959h
695Ah – 8C77h
8C78h – FFFFh
2x CLV
03E8h
6x ZCLV
8x ZCLV
4.22 WRITE (10), WRITE (12) Command
The RelAdr bit is not supported and must be set to zero.
If the drive received a WRITE (10) or a WRITE (12) Command which causes an over rn conditon of the writing buffer, the
execution of the command is deferred until the blank area of the buffer grows to be e to receive whole the data specified in the
command. In this period, the interface bus is held by the drive.
A recording start is carried out when one of the following conditions is realized
1)Write Buffer fills.
2) SYNC CACHE command is received.
In the recording state ,if eject or read request occure daa in a buffer is recorded and it ends. Eject or read request is
performed continuously.
In the recording state ,if a buffer-under-run ocurs, the drive leaves data for 1ECC and interrupts record operation temporarily
until It receive the following Write command.
The Streaming bit of the WRITE (12) Command is reflected to the time-out value of write starting. If Streaming bit is set to one,
the time-out value is set to sec. If Streaming bit is set to zero time-out value is set to 5 sec. The drive maintains the Streaming
bit of the latest Writ(12) Command and determines the time-out value by maintained Streaming bit when writing operation is
started. If sequential data are transferred, the Streaming bit of all WRITE (12) Command needs to keep same value.
The time-ouvale is valid in normal operating condition. If the drive is in abnormal condition, for example play backing the
damarea on the media, the time-out value will be grower by the drive to return from emergency condition of servo
mecm.
The FUA bit and the TSR bit are not supported and these are ignored.
For BD-RE/R, if the Streamig bit is set to one, Stream recording operation is used.
The VNR bit of WRITE(12) is applicable to BD-RE/R.
4.23 WRITE BUFFER Command
This command is used for checking the drive or firmware update.
The specifications of this command are vendor unique.
Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
|