Operation Manual
DVD AV RECEIVER
AVH-P4000DVD
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
3
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
4
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
5
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
01
Precautions
IMPORTANT SAFEGUARDS
Please read all of these instructions regarding
your display and retain them for future refer-
ence.
WARNING
!
Do not attempt to install or service your
display by yourself. Installation or servi-
cing of the display by persons without
training and experience in electronic
equipment and automotive accessories
may be dangerous and could expose you
to the risk of electric shock or other
hazards.
1
Read this manual fully and carefully be-
fore operating your display.
2
Keep this manual handy as a reference for
operating procedures and safety informa-
tion.
3
4
5
Pay close attention to all warnings in this
manual and follow the instructions care-
fully.
Do not allow other persons to use this sys-
tem until they have read and understood
the operating instructions.
To ensure safe driving
WARNING
!
LIGHT GREEN LEAD AT POWER CON-
NECTOR IS DESIGNED TO DETECT
PARKED STATUS AND MUST BE CON-
NECTED TO THE POWER SUPPLY SIDE
OF THE PARKING BRAKE SWITCH. IM-
PROPER CONNECTION OR USE OF
THIS LEAD MAY VIOLATE APPLICABLE
LAW AND MAY RESULT IN SERIOUS IN-
JURY OR DAMAGE.
Do not install the display where it may (i)
obstruct the driver’s vision, (ii) impair the
performance of any of the vehicle’s oper-
ating systems or safety features, includ-
ing air bags, hazard lamp buttons or (iii)
impair the driver’s ability to safely oper-
ate the vehicle.
Do not operate this display if doing so in
any way will divert your attention from
the safe operation of your vehicle. Always
observe safe driving rules and follow all
existing traffic regulations. If you experi-
ence difficulty in operating the system or
reading the display, park your vehicle in a
safe location and make necessary adjust-
ments.
Please remember to wear your seat belt at
all times while operating your vehicle. If
you are ever in an accident, your injuries
can be considerably more severe if your
seat belt is not properly buckled.
Never use headphones while driving.
To promote safety, certain functions are
disabled unless the parking brake is on,
and the vehicle is not in motion.
6
!
!
To avoid the risk of damage and injury and the
potential violation of applicable laws, this unit
is not for use with a video screen that is visible
to the driver.
To avoid the risk of accident and the potential
violation of applicable laws, the front DVD or
TV (sold separately) feature should never be
used while the vehicle is being driven. Also,
rear displays should not be in a location
where it is a visible distraction to the driver.
In some countries or states the viewing of
images on a display inside a vehicle even by
persons other than the driver may be illegal.
Where such regulations apply, they must be
obeyed and this unit’s DVD features should
not be used.
7
!
8
9
When you attempt to watch a DVD, Video CD
or TV while driving, the warning Viewing of
front seat video source while driving is
strictly prohibited. will appear on the front
display.
10 Never set the volume of your display so
high that you cannot hear outside traffic
and emergency vehicles.
6
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Precautions
01
OTHER USE MAY RESULT IN INJURY
OR DAMAGE.
To watch a DVD, Video CD or TV on the front
display, park your vehicle in a safe place and
apply the parking brake.
CAUTION
!
!
The rear view camera function is to be used
as an aid to keep an eye on trailers, or while
backing up. Do not use for entertainment pur-
poses.
Parking brake interlock
Certain functions (DVD/TV viewing and certain
touch panel keys) offered by this unit could be
dangerous and/or unlawful if used while driv-
ing. To prevent such functions from being
used while the vehicle is in motion, there is an
interlock system that senses when the parking
brake is set. If you attempt to use the functions
described above while driving, they will be-
come disabled until you stop the vehicle in a
safe place, and (1) apply the parking brake, (2)
release the parking brake, and then (3) apply
the parking brake again. Please keep the
brake pedal pushed down before releasing the
parking brake.
Please note that the edges of the rear view
camera images may differ slightly according
to whether full screen images are displayed
when backing up, and whether the images are
used for checking the rear when the vehicle is
moving forward.
To avoid battery exhaustion
Be sure to run the vehicle engine while using
this unit. Using this unit without running the
engine can result in battery drainage.
!
When no power is supplied to this unit be-
cause of a replacement of the vehicle bat-
tery or for some similar reason, the
When using a display connected
to REAR MONITOR OUTPUT
This unit’s REAR MONITOR OUTPUT is for
connection of a display to enable passengers
in the rear seats to watch the DVD or TV.
microcomputer of this unit is returned to
its initial condition. We recommend that
you transcribe the audio adjustment data.
WARNING
WARNING
Do not use with vehicles that do not feature an
ACC position.
NEVER install the rear display in a location that
enables the driver to watch the DVD or TV while
driving.
When using a rear view camera
With an optional rear view camera, you are
able to use this unit as an aid to keep an eye
on trailers, or backing into a tight parking
spot.
WARNING
SCREEN IMAGE MAY APPEAR RE-
VERSED.
USE INPUT ONLY FOR REVERSE OR
MIRROR IMAGE REAR VIEW CAMERA.
!
!
7
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
02
Before You Start
Information to User
The backlighting lamp of LCD in this
equipment contains mercury. Dispo-
sal of this material may be regulated
due to environmental considerations
according to Local, State or Federal
Laws. For disposal or recycling infor-
mation, please contact your local
authorities or the Electronics Indus-
Alteration or modifications carried out without
appropriate authorization may invalidate the
user’s right to operate the equipment.
For Canadian model
This Class B digital apparatus complies with
Canadian ICES-003.
CAUTION:
USE OF CONTROL OR ADJUSTMENT OR
PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
About this unit
The tuner frequencies on this unit are allo-
cated for use in North America. Use in other
areas may result in poor reception.
CAUTION:
THE USE OF OPTICAL INSTRUMENTS
WITH THIS PRODUCT WILL INCREASE
EYE HAZARD.
WARNING
Handling the cord on this product or cords asso-
ciated with accessories sold with the product
may expose you to chemicals listed on proposi-
tion 65 known to the State of California and other
governmental entities to cause cancer and birth
defects or other reproductive harm. Wash hands
after handling.
CAUTION
!
Do not allow this unit to come into contact
with liquids. Electrical shock could result.
Also, damage to this unit, smoke, and over-
heating could result from contact with liquids.
Keep this manual handy as a reference for op-
erating procedures and precautions.
Always keep the volume low enough so that
you can hear sounds from outside the vehicle.
Protect this unit from moisture.
!
!
This product contains mercury. Dis-
posal of this material may be regu-
lated due to environmental
!
!
If the battery is disconnected or discharged,
the preset memory will be erased and must be
reprogrammed.
considerations. For disposal or recy-
cling information, please contact
your local authorities or the Electro-
nics Industries Alliance:
Important (Serial number)
The serial number is located on the bottom of
this unit. For your own security and convenience,
be sure to record this number on the enclosed
warranty card.
8
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Before You Start
Playable discs
DVD, Video CD and CD discs that display the
logos shown below can be played back on this
player.
02
The illustration below shows the regions and
corresponding region numbers.
DVD video
Video CD
About this manual
This unit features a number of sophisticated
functions ensuring superior reception and op-
eration. All the functions have been designed
for the easiest possible use, but many are not
self-explanatory. This operation manual will
help you benefit fully from this unit’s potential
and to maximize your listening enjoyment.
We recommend that you familiarize yourself
with the functions and their operation by read-
ing through the manual before you begin
using this unit. It is especially important that
you read and observe WARNINGs and CAU-
TIONs in this manual.
CD
Notes
!
!
is a trademark of DVD Format/Logo
Licensing Corporation.
This player can only play back discs bearing
the marks shown above.
After-sales service for
Pioneer products
Please contact the dealer or distributor from
where you purchased this unit for after-sales
service (including warranty conditions) or any
other information. In case the necessary infor-
mation is not available, please contact the
companies listed below:
Please do not ship your unit to the companies
at the addresses listed below for repair without
advance contact.
DVD video disc region numbers
DVD video discs that have incompatible region
numbers cannot be played on this player. The
region number of the player can be found on
the bottom of this unit.
9
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
02
Before You Start
Features
Touch panel key operation
It is possible to operate this unit by using
touch panel key.
U.S.A.
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
DVD-R/RW compatibility
It is possible to play back DVD-R/RW discs re-
corded with the video format and Video Re-
cording format. (Refer to DVD-R/DVD-RW discs
CANADA
Pioneer Electronics of Canada, Inc.
CUSTOMER SATISFACTION DEPARTMENT
300 Allstate Parkway
Markham, Ontario L3R 0P2
1-877-283-5901
905-479-4411
Video CDs featuring PBC compatibility
It is possible to play back Video CDs featuring
PBC (playback control).
WMA, MP3 and AAC compatibility
For warranty information please see the Lim-
ited Warranty sheet included with this unit.
DivX® video compatibility
Visit our website
Visit us at the following site:
Dolby Digital/DTS compatibility
When using this unit with a Pioneer multi-
channel processor, you can enjoy the atmo-
sphere and excitement provided by DVD movie
and music software featuring 5.1 channel re-
cordings.
1
Register your product. We will keep the details
of your purchase on file to help you refer to
this information in the event of an insurance
claim such as loss or theft.
2
3
Receive updates on the latest products and
technologies.
Download owner’s manuals, order product
catalogues, research new products, and
much more.
!
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic”, and the
double-D symbol are trademarks of Dolby
Laboratories.
4
Your feedback is important in our continual ef-
fort to design and build the most advanced,
cunsumer-focused product in the industry.
Serial number
10
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Before You Start
02
!
Manufactured under license under U.S. Pa-
tent #: 5,451,942 & other U.S. and world-
wide patents issued & pending. DTS and
DTS Digital Out are registered trademarks
and the DTS logos and Symbol are trade-
marks of DTS, Inc. © 1996-2007 DTS, Inc.
All Rights Reserved.
!
Music files on iPod touch can be
played back.
!
!
!
When using an iPod, Interface Cable for
iPod (e.g., CD-I200) is required.
Operations may vary depending on the soft-
ware version of iPod.
iPod is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.
Note
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual prop-
erty rights owned by Macrovision Corporation
and other rights owners. Use of this copyright
protection technology must be authorized by
Macrovision Corporation, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Portable audio player compatibility
!
Inquire at the manufacturer about your
USB portable audio player/USB memory.
This unit corresponds to the following.
— USB MSC (Mass Storage Class) compliant
portable audio player and memory
— WMA, MP3, AAC and WAV file playback
For details about the compatibility, refer to
About WMA
iPod® compatibility
This unit can control and listen to songs on an
iPod.
!
This unit supports only the following iPods.
Supported iPod software versions are
shown below. Older versions of iPod soft-
ware may not be supported.
— iPod third generation (software version
2.3.0)
The Windows Media™ logo printed on the box
indicates that this unit can play back WMA
data.
!
Windows Media and the Windows logo are
trademarks or registered trademarks of
Microsoft Corporation in the United States
and/or other countries.
This unit may not operate correctly depend-
ing on the application used to encode
WMA files.
— iPod fourth generation (software version
3.1.1)
— iPod photo (software version 1.2.1)
— iPod fifth generation (software version
1.2.1)
— iPod mini (software version 1.4.1)
— iPod nano first generation (software ver-
sion 1.3.1)
!
— iPod nano second generation (software
version 1.1.3)
— iPod nano third generation (software
version 1.0.2)
— iPod classic (software version 1.0.2)
— iPod touch (software version 1.1.1)
11
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
02
Before You Start
About MP3
About the SAT RADIO READY mark
Supply of this product only conveys a license
for private, non-commercial use and does not
convey a license nor imply any right to use
this product in any commercial (i.e. revenue-
generating) real time broadcasting (terrestrial,
satellite, cable and/or any other media), broad-
casting/streaming via internet, intranets and/
or other networks or in other electronic con-
tent distribution systems, such as pay-audio or
audio-on-demand applications. An indepen-
dent license for such use is required. For de-
tails, please visit
The SAT RADIO READY mark indicates that
the Satellite Radio Tuner for Pioneer (i.e., XM
tuner and Sirius satellite tuner which are sold
separately) can be controlled by this unit.
Please inquire to your dealer or nearest
authorized Pioneer service station regarding
the satellite radio tuner that can be connected
to this unit. For satellite radio tuner operation,
please refer to the satellite radio tuner owner’s
manual.
!
The system will use direct satellite-to-recei-
ver broadcasting technology to provide lis-
teners in their cars and at home with
crystal-clear sound seamlessly from coast
to coast. Satellite radio will create and
package over 100 channels of digital-quality
music, news, sports, talk and children’s
programming.
About AAC
This unit plays back AAC files encoded by
iTunes®.
!
iTunes is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.
!
“SAT Radio”, the SAT Radio logo and all re-
lated marks are trademarks of Sirius Satel-
lite Radio inc., and XM Satellite Radio
Inc.
About DivX
To protect the LCD screen
DivX is a compressed digital video format cre-
ated by the DivX® video codec from DivX, Inc.
This unit can play DivX video files recorded on
CD-R/RW/ROM and DVD-R/RW/ROM discs.
Keeping the same terminology as DVD video,
individual DivX video files are called “Titles”.
When naming files/titles on a CD-R/RW or a
DVD-R/RW disc prior to burning, keep in mind
that by default they will be played in alphabeti-
cal order.
!
!
!
Do not allow direct sunlight to fall on the
display when this unit is not being used.
Extended exposure to direct sunlight can
result in LCD screen malfunction due to
the resulting high temperatures.
When using a cellular phone, keep the an-
tenna of the cellular phone away from the
display to prevent disruption of the video by
the appearance of spots, colored stripes,
etc.
Official DivX® Certified product
Never touch the screen with anything be-
sides your finger when operating the touch
panel function. The screen can scratch
easily.
Plays all versions of DivX® video (including
DivX® 6) with standard playback of DivX®
media files
!
DivX, DivX Certified, and associated logos
are trademarks of DivX, Inc. and are used
under license.
12
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Before You Start
02
For viewing LCD comfortably
Due to its construction, the viewing angle of
the LCD screen is limited. You can adjust it by
changing either screen size or picture adjust-
ment.
When an operation is prohibited
When you are watching a DVD and attempt to
perform an operation, it may not be performed
because of the programming on the disc.
When this happens, the icon
the screen.
appears on
Changing the wide screen size
!
The icon may not appear with certain
discs.
By changing the screen size from 4:3 to 16:9,
you can adjust the screen so that the screen
can fit to the video image you are playing.
For details concerning operation, refer to
Resetting the microprocessor
Pressing RESET lets you reset the micropro-
cessor to its initial settings without changing
the bookmark information.
The microprocessor must be reset under the
following conditions:
Changing the picture adjustment
You can make the best adjustment to the pic-
ture display by changing BRIGHTNESS,
CONTRAST, COLOR and HUE. You can also
dim or enlight the overall picture image using
DIMMER.
For details concerning operation, refer to
!
Prior to using this unit for the first time
after installation
!
!
If the unit fails to operate properly
When strange or incorrect messages ap-
pear on the display
1
2
Turn the ignition switch OFF.
Press RESET with a pen tip or other
What the marks on DVDs
indicate
pointed instrument.
The marks below may be found on DVD disc
labels and packages. They indicate the type of
images and audio recorded on the disc, and
the functions you can use.
Mark
Meaning
RESET button
Indicates the number of audio sys-
tems.
2
Note
Indicates the number of subtitle lan-
guages.
2
After completing connections or when you want
to erase all memorized settings or return the unit
to its initial (factory) settings, switch your engine
ON or set the ignition switch to ACC ON before
pressing RESET.
Indicates the number of viewing an-
gles.
3
Indicates the picture size (aspect ratio:
screen width-to-height ratio) type.
16 : 9 LB
1
Indicates the number of the region
where playback is possible.
ALL
13
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
02
Before You Start
Feature demo mode
The feature demo automatically starts when
you select the source OFF. The demo con-
tinues while the ignition switch is set to ACC
or ON. To cancel the feature demo, press and
hold VOLUME/MUTE. To restart the feature
demo, press and hold VOLUME/MUTE again.
Remember that if the feature demo continues
operating when the car engine is turned off, it
may drain battery power.
Important
The red lead (ACC) of this unit should be con-
nected to a terminal coupled with ignition switch
on/off operations. If this is not done, the vehicle
battery may be drained.
14
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
4
1 2 3
7 6
8
5
8 AUX1 input jack (3.5 mm stereo/video
jack)
Use to connect an auxiliary device.
What’s What
Head unit
1 SRC button
This unit is turned on by selecting a source.
Press to cycle through all the available
sources.
Optional remote control
The remote control CD-R55 is sold separately.
For details concerning operations, see the re-
mote control manual.
2 h (eject) button
Press to eject a disc from this unit.
3 RESET button
Press to return to the factory settings (initial
settings).
4 Disc loading slot
Insert a disc to play.
5 VOLUME/MUTE button
Rotate it to increase or decrease the vo-
lume.
Press to cut the sound.
6 EQ button
Press to select various equalizer curves.
7 DISP OFF button
Press to turn the information display on or
off.
15
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
!
!
!
RADIO – Radio
iPod – iPod
USB – USB portable audio player/USB
memory
TEL – Bluetooth telephone
BT Audio – Bluetooth audio player
S-DVD – DVD player/multi-DVD player
MCD – Multi-CD player
AUX 1 – AUX 1
AUX 2 – AUX 2
AV – AV input
TV – Television
EXT 1 – External unit 1
EXT 2 – External unit 2
XM – XM tuner
SIRIUS – SIRIUS tuner
REARVIEW – Rear view camera
OFF – Turn the unit off
Basic Operations
Power ON/OFF
1
!
!
!
!
!
!
!
!
!
!
!
!
!
!
1 Source icon
Turning the unit on
%
When using the touch panel keys,
touch the source icon and then touch the
desired source name.
#
When the source icon is not displayed, you
can display it by touching the screen.
While operating the menu, you cannot select
a source by touching the source icon.
The source names are displayed and select-
able ones are highlighted.
#
%
When using the button, press SRC to
#
To close source select menu, touch ESC.
turn the unit on.
%
When using the button, press SRC re-
peatedly to select a desired source.
Turning the unit off
Notes
%
When using the touch panel keys,
touch the source icon and then touch OFF.
When the source icon is not displayed, you
can display it by touching the screen.
!
In the following cases, the sound source will
not change.
— When no unit corresponding to the se-
lected source is connected.
— When there is no disc or magazine in the
player.
#
%
When using the button, press SRC and
hold until the unit turns off.
— When AUX (auxiliary input) is set to off
(refer to page 38).
— When the AV (AV input) is not set to
AUX1 is set to VIDEO by default. Set the AUX1
REARVIEW (rear view camera) cannot be se-
lected by pressing SRC.
Image from rear view camera can be dis-
played automatically when the appropriate
setting is conducted. For details, refer to Set-
Selecting a source
You can select a source you want to listen to.
To switch to the DVD player, load a disc in the
unit. To switch to the iPod or USB, connect an
iPod or USB portable audio player/USB mem-
ory to this unit.
!
!
!
%
When using the touch panel keys,
touch the source icon and then touch the
desired source name.
The source names are displayed and select-
able ones are highlighted.
!
DVD – Built-in DVD player
16
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
!
!
External unit refers to a Pioneer product (such
as ones available in the future) that, although
incompatible as a source, enables control of
basic functions with this unit. Two external
units can be controlled with this unit. When
two external units are connected, the external
unit is automatically allocated to external unit
1 or external unit 2 by this unit.
When this unit’s blue/white lead is connected
to the vehicle’s auto-antenna relay control
terminal, the vehicle’s antenna extends when
this unit’s source is turned on. To retract the
antenna, turn the source off.
Note
If you do not use the touch panel keys within 30
seconds, they will be hidden automatically when
selecting video sources.
Operating the menu
1 2 3
Adjusting the volume
%
Use VOLUME/MUTE to adjust the
4
sound level.
Rotate VOLUME/MUTE to increase or de-
crease the volume.
1 FUNCTION MENU key
Touch to select functions for each source.
2 AUDIO MENU key
Touch to select various sound quality controls.
3 SYSTEM MENU key
Touch to select various setup functions.
4 ESC key
Touch panel key basic operation
Activating the touch panel keys
Touch to cancel the control mode of func-
tions.
1
Touch AV MENU to display MENU.
The menu names are displayed and operable
ones are highlighted.
#
When AV MENU is not displayed, you can dis-
play it by touching the screen.
1
2
Touch the desired key to display the
function names you want to operate.
To go to the next group of function names,
touch NEXT.
1 Touch panel keys
Touch to do various operations.
#
1
Touch the screen to activate the touch
panel keys corresponding to each source.
#
To return to the previous group of function
The touch panel keys appear on the display.
names, touch PREV.
#
To go to the next group of touch panel keys,
3
Touch ESC to return to the display of
touch NEXT.
#
each source.
To return to the previous group of touch panel
keys, touch PREV.
2
Touch HIDE to hide the touch panel
keys.
17
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
Radio
the iPod charge setting off and noise is disap-
peared. (Refer to Switching the iPod charge setting
Basic Operations
1 2
3
4
Storing and recalling broadcast
frequencies
You can easily store up to six broadcast fre-
quencies for later recall.
!
Up to 18 FM stations, six for each of the
three FM bands, and six AM stations can
be stored in memory.
1
2
Touch LIST to display the preset list.
6 5
1 Source icon
2 Band indicator
When you find a frequency that you
want to store in memory keep touching
one of preset tuning keys P1 to P6 until the
beep sounds.
The selected radio station frequency has been
stored in memory.
The next time you touch the same preset tun-
ing key the radio station frequency is recalled
from memory.
3 Preset number indicator
4 Frequency indicator
5 LOCAL indicator
Appears when local seek tuning is on.
6 5 (stereo) indicator
Appears when the selected frequency is being
broadcast in stereo.
1
Touch the source icon and then touch
3
Touch ESC to return to the ordinary dis-
RADIO to select the radio.
play.
2
Touch BAND to select a band.
Note
Touch BAND until the desired band (FM1,
You can also use a and b to recall radio station
frequencies assigned to preset tuning keys P1 to
P6.
FM2, FM3 for FM or AM) is displayed.
3
To perform manual tuning, briefly
touch c or d.
4
To perform seek tuning, keep touching
Introduction of advanced
operations
c or d for about one second and release.
The tuner will scan the frequencies until a
broadcast strong enough for good reception is
found.
1
Touch AV MENU and then touch
FUNCTION MENU to display the function
names.
The function names are displayed and oper-
able ones are highlighted.
#
You can cancel seek tuning by briefly touching
either c or d.
If you keep touching c or d you can skip sta-
#
tions. Seek tuning starts as soon as you release
the key.
2
Touch ESC to return to the frequency
display.
To return to the previous display, touch BACK.
#
Note
Listening AM radio while an iPod is charged from
this unit may generate noise. In this case, turn
18
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
Storing the strongest broadcast
frequencies
BSM (best stations memory) lets you automa-
tically store the six strongest broadcast fre-
quencies under preset tuning keys P1 to P6
and once stored there you can tune in to those
frequencies with the touch of a key.
Built-in DVD player
Basic Operations
1 2
3
4
5
!
Storing broadcast frequencies with BSM
may replace broadcast frequencies you
have saved using P1 to P6.
%
Touch BSM on the function menu to
turn BSM on.
6
BSM begins to flash. While BSM is flashing
the six strongest broadcast frequencies will be
stored under preset tuning keys P1 to P6 in
order of their signal strength. When finished,
BSM stops flashing.
1 Source icon
2 Media indicator
Shows the type of disc currently playing.
3 Title/Folder number indicator
DVD: shows the title currently playing.
Compressed audio and DivX: shows the folder
currently playing.
#
To cancel the storage process, touch BSM
again.
4 Chapter/track/file number indicator
DVD: shows the chapter currently playing.
Video CD and CD: shows the track currently
playing.
Compressed audio and DivX: shows the file
currently playing.
5 Play time indicator
Tuning in strong signals
Local seek tuning lets you tune in only those
radio stations with sufficiently strong signals
for good reception.
%
Touch LOCAL on the function menu to
set the sensitivity.
6 Variable message area
Touch LOCAL repeatedly until the desired level
of sensitivity appears in the display.
There are four levels of sensitivity for FM and
two levels for AM:
FM: OFF—LEVEL1—LEVEL2—LEVEL3—
LEVEL4
DVD: shows the subtitle language, audio lan-
guage and viewing angle.
CD TEXT, compressed audio and DivX: shows
the text information of currently playing disc.
1
Insert a disc into the disc loading slot.
AM: OFF—LEVEL1—LEVEL2
Playback will automatically start.
The LEVEL4 setting allows reception of only
the strongest stations, while lower settings let
you receive progressively weaker stations.
#
#
Be sure to turn up the label side of a disc.
After a disc has been inserted, use touch
panel keys to select the DVD player.
#
When the automatic playback function is on,
this unit will cancel the DVD menu and automati-
cally start playback from the first chapter of the
#
With some DVD discs, a menu may be dis-
19
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
#
With a Video CD featuring the PBC (playback
!
If a disc contains a mixture of various media
file types such as DivX and MP3, you can
switch between media file types to play. Refer
There is sometimes a delay between starting
up disc playback and the sound being issued.
When being read, FORMAT READ is dis-
played.
When playing back files recorded as VBR
(variable bit rate) files, the play time will not be
correctly displayed if fast forward or reverse
operations are used.
When playing back WMA files, album title list
does not appear.
control) function, a menu is displayed. (Refer to
#
To eject a disc, press h (eject).
2
Touch the screen to display the touch
!
!
panel keys.
3
When playing a compressed audio or
DivX, touch a or b to select a folder.
#
To return to folder 01 (ROOT), touch and hold
. However, if folder 01 (ROOT) contains no files,
playback commences with folder 02.
is displayed only when the list is operated.
!
!
4
To skip back or forward to another
chapter/track, briefly touch o or p.
During PBC playback, a menu may be dis-
played if you perform these operations.
If the characters recorded on the disc are not
compatible with this unit, those characters
will not be displayed.
#
5
To perform fast forward or reverse,
Basic playback controls
keep touching o or p.
When DVD, DivX disc or Video CD is playing, if
you keep touching o or p for five sec-
onds, the icon m or n is highlighted.
When this happens, fast reverse/fast forward
continues even if you release o or p. To
resume playback at a desired point, touch
de.
The table below shows the basic controls for
playing discs. The following chapters cover
other playback features in more details.
Key What it does
Starts playback, pauses a disc that’s playing or
restarts a paused disc.
de
#
When playing DVD video or Video CD, fast for-
g
Stops playback.
ward/fast reverse may not be possible at certain
locations on some discs. If this happens, normal
playback automatically resumes.
Skips to the start of the current track, chapter
or file, then to previous tracks/chapters/files.
o
!
Performs fast reverse by touching and
holding o.
Notes
Skips to the next track, chapter or file.
p
!
Performs fast forward by touching and
holding p.
!
!
If you do not use the touch panel keys within
30 seconds, they will be hidden automatically
when displaying video image.
Read the precautions for discs and player on
If an error message such as ERROR-02-XX is
If bookmark function is on, DVD playback re-
sumes from the selected point. For more de-
Note
You may find with some DVD or Video CD discs
that some playback controls do not work in cer-
tain parts of the disc. This is not a malfunction.
!
!
20
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
Using the touch panel keys
Touch to display touch panel keys
to operate the DVD menu.
When the touch panel keys are not displayed,
you can display them by touching the screen.
To switch to the DVD menu direct touch con-
trol, touch TOUCH.
Switching the media file type
When playing a disc containing a mixture of
various media file types such as DivX and
MP3, you can switch between media file types
to play.
1
#
!
This unit allows playback of the following
media file type recorded on CD-R/RW/ROM
discs.
#
2
Touch a, b, c or d to select the desired
— Audio data (CD-DA)
— Compressed audio files (WMA/MP3/
AAC)
menu item.
3
Touch ENTER.
— DivX video files
Playback starts from the selected menu item.
!
In case of DVD-R/RW/ROM, this unit does
not allow playback of audio data (CD-DA).
#
The way to display the menu differs depending
on the disc.
%
Touch MEDIA to switch between media
file types.
PBC playback
During playback of Video CDs featuring PBC
(Playback Control), PBC ON is displayed. You
can operate PBC menu with 10Key.
Touch MEDIA repeatedly to switch between
the following media file types:
CD (audio data (CD-DA))—WMA/MP3/AAC
(compressed audio)—DivX (DivX video files)
!
This function is available for Video CD.
1
When PBC menu is displayed, touch
Operating the DVD menu
Some DVDs allow you to select from the disc
contents using a menu.
SEARCH and then touch 10Key.
Depending on the discs, the menu may be
#
two or more pages long. In such case, touch o
or p to display the next or previous menu.
!
!
This function is available for DVD video.
You can display the menu by touching
MENU or TOP MENU while a disc is play-
ing. Touching either of these keys again
lets you start playback from the location se-
lected from the menu. For details, refer to
the instructions provided with the disc.
2
Touch 0 to 9 corresponding to a menu
number and then touch ENTER to start
playback.
Playback starts from the selected menu item.
3
Touch ESC to hide the touch panel keys.
Using DVD menu direct touch control
This function allows you to operate the DVD
menu by touching the menu item directly.
Notes
!
You can display the menu by touching
RETURN during PBC playback. For details,
refer to the instructions provided with the
disc.
PBC playback of Video CD cannot be can-
celled.
During playback of Video CDs featuring PBC
(Playback Control), PBC ON, search and time
search functions cannot be used nor can you
select the range for repeat play.
%
Touch the desired menu item on the
DVD menu directly.
Depending on the contents of DVD discs, this
#
!
!
function may not work properly. In this case,
using touch panel keys operate the DVD menu.
21
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
®
%
To skip back or forward to another title,
Playing DivX VOD content
touch a or b.
Some DivX VOD (video on demand) content
may only be playable a fixed number of times.
When you load a disc containing this type of
DivX VOD content, the remaining number of
plays is shown on-screen and you then have
the option of playing the disc (thereby using
up one of the remaining plays), or stopping. If
you load a disc that contains expired DivX
VOD content (for example, content that has
zero remaining plays), Rental Expired. is dis-
played.
Touching a skips to the start of the next title.
Touching b skips to the start of the previous
title.
Title numbers are displayed for eight seconds.
#
To switch between groups of touch panel keys,
touch NEXT or PREV.
CM skip/CM back
This function skips a reproduced image for a
specified time. If the currently playing disc
contains commercials, it is possible to skip
them.
!
If your DivX VOD content allows an unlim-
ited number of plays, then you may load
the disc into your player and play the con-
tent as often as you like, and no message
will be displayed.
!
This function is available for DVD.
%
To skip progressively backward or for-
ward, touch or
Each time you touch or it changes steps
in the following order:
.
Important
!
In order to play DivX VOD content on this unit,
you first need to register the unit with your
DivX VOD content provider. About your regis-
DivX VOD content is protected by a DRM (Di-
gital Rights Management) system. This re-
stricts playback of content to specific,
registered devices.
CM back
5 sec.—15 sec.—30 sec.—1.0 min.—2.0
min.—3.0 min.—0 sec.
CM skip
30 sec.—1.0 min.—1.5 min.—2.0 min.—3.0
min.—5.0 min.—10.0 min.—0 sec.
!
Resume playback (Bookmark)
The Bookmark function lets you resume play-
back from a selected scene the next time the
disc is loaded.
%
If the message is displayed after load-
ing a disc containing DivX VOD content,
touch PLAY.
!
This function is available for DVD video.
Playback of the DivX VOD content will start.
#
#
To skip to the next file, touch NEXT PLAY.
If you do not want to play the DivX VOD con-
%
During playback, touch BOOKMARK at
the point you want to resume playback
next time.
tent, touch STOP.
The selected scene will be bookmarked so that
playback resumes from that point next time.
You can bookmark up to five discs. After that,
the oldest bookmark is replaced by the new
one.
Skipping back or forward to
another title
!
This function is available for DVD.
#
To switch between groups of touch panel keys,
touch NEXT or PREV.
To clear the bookmark on a disc, keep touch-
ing BOOKMARK during playback.
#
22
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
#
You can also bookmark a disc by pressing and
Changing audio language
during playback (Multi-audio)
DVDs can provide audio playback with differ-
ent languages and different systems (Dolby Di-
gital, DTS etc.). With DVDs featuring multi-
audio recordings, you can switch between lan-
guages/audio systems during playback.
holding EJECT at the point you want to bookmark.
Next time you load the disc, playback will resume
from the bookmarked point. Note that you can
only bookmark one disc using this method. To
clear the bookmark on a disc, press EJECT.
!
This function is available for DVD and DivX
disc.
Searching for the part you
want to play
You can use the search function to find the
part you want to play.
%
Touch AUDIO during playback.
Each time you touch AUDIO it switches be-
tween audio systems.
#
!
This function is available for DVD, DivX
disc and Video CD.
To switch between groups of touch panel keys,
!
Chapter search, track search and time
search are not possible when disc playback
has been stopped.
touch NEXT or PREV.
Notes
!
During playback of Video CDs featuring
PBC (playback control), this function can-
not be operated.
!
!
!
With some DVDs, switching between lan-
guages/audio systems may only be possible
using a menu display.
You can also switch between languages/audio
systems using DVD SETUP. For details, refer
Only digital output of DTS audio is possible. If
this unit’s optical digital outputs are not con-
nected, DTS audio will not be output, so select
an audio setting other than DTS.
Display indications such as Dolby D and
5.1ch indicate the audio system recorded on
the DVD. Depending on the setting, playback
may not be with the same audio system as
that indicated.
Touching AUDIO during fast forward/fast re-
verse, pause or slow motion playback returns
you to normal playback.
1
Touch SEARCH.
#
To switch between groups of touch panel keys,
touch NEXT or PREV.
2
Touch the desired search option (e.g.,
CHAP.).
#
You cannot operate this step during DivX disc
playback.
!
!
3
Touch 0 to 9 to input the desired num-
ber.
#
#
To cancel the inputted numbers, touch C.
In the time search function, to select 1 hour
11 minutes, convert the time into 71 minutes 00
seconds and touch 7, 1, 0 and 0 in that order.
4
Touch ENTER.
This starts playback from the selected part.
Changing the subtitle language
during playback (Multi-subtitle)
Note
With DVDs featuring multi-subtitle recordings,
you can switch between subtitle languages
during playback.
With DVD discs featuring a menu, you can also
touch MENU or TOP MENU and then make se-
lections from the displayed menu.
!
This function is available for DVD and DivX
disc.
23
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
%
Touch SUBTITLE during playback.
Frame-by-frame playback
This lets you move ahead one frame at a time
during playback.
Each time you touch SUBTITLE it switches be-
tween subtitle languages.
#
To switch between groups of touch panel keys,
!
This function is available for DVD and
Video CD.
touch NEXT or PREV.
%
Touch r during playback.
Notes
Each time you touch r, you move ahead one
frame.
!
!
!
With some DVDs, switching between subtitle
languages may only be possible using a menu
display.
You can also switch between subtitle lan-
guages using DVD SETUP. For details, refer to
Touching SUBTITLE during fast forward/fast
reverse, pause or slow motion playback re-
turns you to normal playback.
#
#
To return to normal playback, touch de.
To switch between groups of touch panel keys,
touch NEXT or PREV.
With some discs, images may be unclear dur-
#
ing frame-by-frame playback.
Slow motion playback
This lets you slow down playback speed.
!
This function is available for DVD and
Video CD.
Changing the viewing angle
during playback (Multi-angle)
%
Keep touching r until is displayed
during playback.
With DVDs featuring multi-angle (scenes shot
from multiple angles) recordings, you can
switch among viewing angles during play-
back.
The icon is displayed, forward slow motion
playback begins.
#
Touching r during slow motion playback,
you can change the playback speed in four steps
as follows:
1/16—1/8—1/4—1/2
!
!
This function is available for DVD video.
During playback of a scene shot from mul-
#
To switch between groups of touch panel keys,
touch NEXT or PREV.
tiple angles, the angle icon
is dis-
played. Turn angle icon display on or off
#
To return to normal playback, touch de.
Notes
!
!
!
There is no sound during slow motion play-
back.
With some discs, images may be unclear dur-
ing slow motion playback.
Reverse slow motion playback is not possible.
%
Touch ANGLE during playback of a
scene shot from multiple angles.
Each time you touch ANGLE it switches be-
tween angles.
#
To switch between groups of touch panel keys,
touch NEXT or PREV.
Return to the specified scene
Note
You can return to the specified scene where
the DVD you are currently playing has been
preprogrammed to return.
Touching ANGLE during fast forward/fast reverse,
pause or slow motion playback returns you to
normal playback.
!
This function is available for DVD video.
%
Touch RETURN to return to the speci-
fied scene.
#
To switch between groups of touch panel keys,
touch NEXT or PREV.
24
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
#
If a specified scene has not been prepro-
track title, artist’s name and playback time
and are called CD TEXT discs.
If specific information has not been recorded
on a CD TEXT disc, No XXXX will be displayed
(e.g., No name).
If specific information has not been recorded
on a compressed audio disc, No XXXX will be
displayed (e.g., NO name).
When playing back WMA files, album title is
not displayed.
grammed in DVD disc, this function is not possi-
ble.
!
!
!
Automatic playback of DVDs
When a DVD disc with DVD menu is inserted,
this unit will cancel the DVD menu automati-
cally and start playback from the first chapter
of the first title.
!
!
This function is available for DVD video.
Some DVDs may not operate properly. If
this function is not fully operated, turn this
function off and start playback.
Selecting tracks from the track list
Track list lets you see the list of tracks on a
disc and select one of them to play back.
When playing a CD TEXT disc, track titles are
displayed.
%
Touch AUTO PLAY to turn automatic
playback on.
#
To turn automatic playback off, touch
AUTO PLAY again.
To switch between groups of touch panel keys,
touch NEXT or PREV.
When the automatic playback is on, you can-
!
1
2
This function is available for CD.
#
Touch LIST.
Touch or to switch between the
lists of tracks.
#
not operate repeating play of DVD disc (refer to
3
Touch your favorite track.
That selection will begin to play.
4
Touch ESC to return to the ordinary dis-
Text information
Text information recorded on a disc can be dis-
played. Text information is displayed on vari-
able message area.
play.
Selecting files from the file
name list
!
This function is available for CD TEXT, com-
pressed audio disc and DivX disc.
File name list lets you see the list of file names
(or folder names) and select one of them to
playback.
Displaying text information
Touch INFO.
Touch INFO repeatedly to switch between the
following settings:
For CD TEXT discs
%
!
This function is available for compressed
audio disc and DivX disc.
1
2
Touch LIST.
: disc title— : disc artist name— : track
title— : track artist name
Touch or to switch between the
lists of titles.
For compressed audio discs
: folder name— : file name— : album
title— : track title— : artist name
For DivX discs
3
Touch your favorite file name (or folder
name).
That selection will begin to play.
#
When you have selected a folder, a list of the
: folder name— : file name
names of the files (or the folders) in it can be
viewed. Repeat steps 2 and 3 to select the desired
file name.
Notes
!
Some discs have certain information encoded
on the disc during manufacture. These discs
may contain such information as the CD title,
#
To return to the previous list (the folder one
level higher), touch
.
25
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
#
To return to folder 01 (ROOT), touch and hold
. However, if folder 01 (ROOT) contains no files,
!
!
If you select another folder during repeat play,
the repeat play range changes to DISC.
When playing back compressed audio or
DivX, if you perform track search or fast for-
ward/reverse during FILE, the repeat play
range changes to FOLDER.
playback commences with folder 02.
4
play.
Touch ESC to return to the ordinary dis-
!
When playing back Video CD or CD, if you per-
form track search or fast forward/reverse dur-
ing TRACK, the repeat play range changes to
DISC.
Introduction of advanced
operations
!
!
When FOLDER is selected, it is not possible to
play back a subfolder of that folder.
When playing discs with compressed audio
and audio data (CD-DA), repeat play performs
within the currently playing data type even if
DISC is selected.
1
Touch AV MENU and then touch
FUNCTION MENU to display the function
names.
The function names are displayed and oper-
able ones are highlighted.
2
Touch ESC to return to the playback dis-
play.
#
To return to the previous display, touch BACK.
Playing tracks in random order
Tracks in a selected repeat range are played in
random order.
Repeating play
!
This function is available for CD and com-
pressed audio disc.
Tracks in a play range are played repeatedly.
Play range varies depending on the media.
For DVD, play range can be selected from
DISC (disc repeat), TITLE (title repeat) and
CHAPTER (chapter repeat).
For Video CD and CD, play range can be se-
lected from DISC (disc repeat) and TRACK
(track repeat).
1
Select the repeat range.
2
Touch RANDOM on the function menu
to turn random play on.
Tracks will play in a random order within the
previously selected repeat range.
For compressed audio and DivX, play range
can be selected from DISC (disc repeat),
FOLDER (folder repeat) and FILE (file repeat).
#
To turn random play off, touch RANDOM
again.
!
During playback of Video CDs featuring
PBC (playback control), this function can-
not be operated.
Scanning tracks or folders
Scan play lets you hear the first 10 seconds of
each track on the CD.
When playing the compressed audio disc, the
first 10 seconds of each track of the current
folder (or the first track of each folder) is
played.
%
Touch REPEAT on the function menu to
select the repeat range.
!
!
!
!
!
!
TITLE – Repeat the current title
CHAPTER – Repeat the current chapter
TRACK – Repeat the current track
FILE – Repeat just the current file
FOLDER – Repeat the current folder
DISC – Play through the current disc
!
This function is available for CD and com-
pressed audio disc.
1
Select the repeat range.
Notes
2
Touch SCAN on the function menu to
!
If you perform chapter search or fast forward/
reverse, the repeat play range changes to
DISC.
turn scan play on.
The first 10 seconds of each track is played.
26
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
3
When you find the desired track (or
Playing songs on iPod
Basic Operations
You can use this unit to control an iPod by
using a cable (e.g., CD-I200), which is sold se-
parately.
folder) touch SCAN again.
Note
After track or folder scanning is finished, normal
playback of the tracks will begin again.
1 2
3
4
5
6
Selecting audio output
When playing DVD video discs recorded with
LPCM audio, you can switch the audio output.
When playing Video CD discs, you can switch
between stereo and monaural audio output.
!
!
!
This function is available for DVD and
Video CD.
This function is not possible when disc
playback has been stopped.
If you select Linear PCM, when playing a
disc recorded on a dual mono mode, you
can operate this function. (Refer to Setting
8
7
1 Source icon
2 Repeat indicator
Shows when repeat range is set to ONE or
ALL.
3 Song number indicator
4 Title indicator
5 Shuffle indicator
Shows when random play is set to SONGS or
ALBUMS.
6 Play time indicator
%
Touch L/R SELECT on the function menu
to select the audio output.
Touch L/R SELECT repeatedly until the desired
audio output appears in the display.
!
!
!
!
L+R – left and right
LEFT – left
RIGHT – right
7 Song information
MIX – mixing left and right
Shows detailed information of currently play-
ing song.
8 Battery charging indicator
Shows when the battery charge setting is on.
Note
Depending on the disc and the playback location
on the disc, the function may not be selectable,
indicating that operating this function is not pos-
sible.
1
Connect the iPod to this unit.
Playback will automatically start.
While connected to this unit, PIONEER, Acces-
sory Attached or (check mark) is displayed
on the iPod.
Using compression
Using the COMP (compression) function lets
you adjust the sound playback quality of this
unit.
#
Before connecting the dock connector of this
unit to the iPod, disconnect the headphones from
the iPod.
#
Depending on the model of iPod or the data
size in the iPod, there may be a delay to start play-
ing after connection.
%
Touch COMPRESSION on the function
menu to select your favorite setting.
#
After the iPod has been connected to this
unit, use touch panel keys to select the iPod.
When removing the iPod from this unit, this
unit is turned off.
OFF—COMP1—COMP2
#
2
To skip back or forward to another
song, touch o or p.
27
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
3
To perform fast forward or reverse,
1
2
Touch MENU to display iPod menus.
Touch one of the categories in which
keep touching o or p.
4
When playing a file with chapter, touch
o or p to select a chapter.
To switch between groups of touch panel keys,
you want to search for a song/video.
When browsing for a song
#
!
!
!
!
!
!
!
!
PLAYLISTS (playlists)
ARTISTS (artists)
ALBUMS (albums)
SONGS (songs)
PODCASTS (podcasts)
GENRES (genres)
touch NEXT or PREV.
Notes
!
!
Read the precautions for iPod on page 90.
If an error message or icon such as ERROR-11
COMPOSERS (composers)
AUDIOBOOKS (audiobooks)
or
When browsing for a video
!
!
Connect directly the dock connector cable to
the iPod so that this unit works properly.
When the ignition switch is set to ACC or ON,
the iPod’s battery is charged while the iPod is
connected to this unit.
While the iPod is connected to this unit, the
iPod cannot be turned on or off.
!
!
!
!
!
V.PLAYLISTS (playlists)
MOVIES (movies)
MUSICVIDEOS (music video)
V.PODCASTS (video podcasts)
TV SHOWS (TV shows)
!
!
#
To switch between groups of categories, touch
PREV or NEXT.
The iPod is turned off about two minutes after
the ignition switch is set to OFF.
3
Touch a list title that you want to play.
Repeat this operation until you find the de-
sired song/video.
Playing video
This unit can play video if an iPod with video
capabilities is connected.
#
You can start playback throughout the se-
lected list by touching and holding desired list
title.
#
You can start a playback of all the songs in the
selected list (GENRES, ARTISTS, COMPOSERS or
!
To pause video playback, touch MENU.
This unit can play back “Movies”, “Music vi-
deos”, “Video Podcast” and “TV show”
which are downloaded from iTunes store.
Change the video setting on the iPod so
that the iPod can output the video to an ex-
ternal device, before you display the video
screen.
!
ALBUMS). To do this, touch ALL.
#
You can start a playback of all the videos in
the selected list (MUSICVIDEOS or TV SHOWS).
!
!
To do this, touch ALL.
#
To switch between the lists of titles, touch or
.
#
To return to the previous menu, touch MENU.
For details, refer to the iPod’s manuals.
4 Touch ESC to return to the ordinary dis-
play.
1
#
Touch Video.
To return to the music operation screen, touch
Music.
2
Play video on the iPod.
Displaying text information on
iPod
Browsing for a song/video
%
Touch INFO to select the desired text in-
formation.
Operations to control an iPod with this unit is
designed to be as close to the iPod as possible
to make operation and song/video search
easy.
: song title— : artist name— : album title
#
If the characters recorded on the iPod are not
compatible with this unit, those characters are
not displayed.
!
If the characters recorded on the iPod are
not compatible with this unit, those charac-
ters are not displayed.
28
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
Repeating play
For playback of the songs on the iPod, there
are two repeat play ranges: ONE (repeat one
song) and ALL (repeat all songs in the list).
03
!
While this function is in use, even if the
ignition key is turned off, iPod is not turned
off. To turn off power, operate the iPod.
1
#
Touch
Touching
to switch the control mode.
switches the control mode to
!
While repeat play range is set to ONE, you
cannot select the other songs. However,
you can select other songs while browsing.
this unit.
#
While using this function, play time and titles
are not displayed on this unit.
Even if this function is performed, track up/
1
2
Touch NEXT.
#
down, chapter up/down and fast forward/reverse
can be operated from this unit.
Touch
to select the repeat range.
!
!
ONE – Repeat just the current song
#
While using this function, browse function
ALL – Repeat all songs in the selected list
To switch between groups of touch panel keys,
cannot be operated from this unit.
#
touch NEXT or PREV.
2
Operate the connected iPod to select a
song/video and play.
Playing songs in a random
order (shuffle)
For playback of songs on the iPod, there are
two random play methods: SONGS (play back
songs in a random order) and ALBUMS (play
back albums in a random order).
Pausing a song
%
#
Touch de during playback.
To resume playback at the same point that you
turned pause on, touch de again.
%
Touch
to select the random play
Selecting songs from album list
of currently playing artist
Album list of the currently selected artist is
displayed. You can select an album or song
from the artist name.
method.
!
!
SONGS – Play back songs in the selected
list in random order.
ALBUMS – Play back songs from a ran-
domly selected album in order.
#
To cancel the random play, touch
repeat-
!
!
This function is not available for video files.
Depending on the number of files in the
iPod, there may be a delay when displaying
a list.
edly until the shuffle icon is turned off.
Playing all songs in a random
order (shuffle all)
This method plays all songs on the iPod ran-
domly.
1
2
Touch NEXT.
Touch LINK SEARCH to turn link search
on.
Searches albums of the artist and displays the
list.
%
Touch
to turn shuffle all on.
All songs on the iPod play randomly.
3
Touch a list title that you want to play.
For more details about the selecting operation,
Operating this unit’s iPod
function from your iPod
This unit’s iPod function can be operated from
your iPod. Sound can be heard from car’s
speaker, and operation can be conducted from
your iPod.
Note
If link search is aborted, NOT FOUND is dis-
played.
29
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
Changing audiobook speed
While listening to an audiobook on iPod, play-
back speed can be changed.
Playing songs on USB portable
audio player/USB memory
Basic Operations
For details about the supported device, refer to
%
Touch A.Book to select your favorite
setting.
!
FASTER – Playback faster than normal
speed
NORMAL – Playback in normal speed
SLOWER – Playback slower than normal
speed
1 2
3 4 5
6
!
!
#
To switch between groups of touch panel keys,
touch NEXT or PREV.
7
1 Source icon
2 Media indicator
Shows the type of file currently playing.
3 Folder number indicator
4 File number indicator
5 Title indicator
6 Play time indicator
7 Song information
Shows detailed information of currently play-
ing song.
1
Touch the source icon and then touch
USB to select the USB.
When the source icon is not displayed, you
can display it by touching the screen.
#
2
#
Touch a or b to select a folder.
To return to folder 01 (ROOT), touch and hold
. However, if folder 01 (ROOT) contains no files,
playback commences with folder 02.
is displayed only when the list is operated.
#
You cannot select a folder that does not have
a compressed audio file recorded in it.
3
To perform fast forward or reverse,
keep touching o or p.
4
To skip back or forward to another
compressed audio file, briefly touch o or
p.
30
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
Notes
Function name Operation
!
Optimum performance of this unit may not be
obtained depending on the connected USB
portable audio player/USB memory.
If folder 01 (ROOT) contains no files, playback
commences with folder 02.
However, the repeat play ranges
you can select are different from
that of the built-in DVD player. The
repeat play ranges of the USB por-
table audio player/USB memory
are:
!
!
REPEAT
When the USB portable audio player having
battery charging function is connected to this
unit and the ignition switch is set to ACC or
ON, the battery is charged.
You can disconnect the USB portable audio
player/USB memory anytime you want to fin-
ish listening to it.
If USB portable audio player/USB memory is
connected to this unit, the source is changed
to USB automatically. If you do not use an
USB device, disconnect it from this unit. De-
pending on the connected USB device, turn-
ing on the ignition switch while USB device is
connected to this unit may change the source
automatically.
!
!
!
FILE – Repeat just the current
file
FOLDER – Repeat the current
folder
!
!
ALL – Repeat all files
Refer to Playing tracks in random
RANDOM
SCAN
Refer to Scanning tracks or folders
Notes
!
!
If you select another folder during repeat play,
the repeat play range changes to ALL.
If you perform track search or fast forward/re-
verse during FILE, the repeat play range
changes to FOLDER.
Pausing compressed audio
playback
Touch de during playback.
To resume playback at the same point that you
turned pause on, touch de again.
!
!
When FOLDER is selected, it is not possible to
play back a subfolder of that folder.
After file or folder scanning is finished, nor-
mal playback of the files begins again.
%
#
Displaying text information of
an audio file
The operation is the same as that of the built-
in DVD player.
Introduction of advanced
operations
1
Touch AV MENU and then touch
FUNCTION MENU to display the function
names.
!
If the characters recorded on the audio file
are not compatible with this unit, those
characters will not be displayed.
The function names are displayed and oper-
able ones are highlighted.
2
Touch ESC to return to the playback dis-
play.
Selecting files from the file
name list
#
To return to the previous display, touch BACK.
The operation is the same as that of the built-
in DVD player.
Function and operation
REPEAT, RANDOM and SCAN operations are
basically the same as that of the built-in DVD
player.
31
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
2
Touch a or b to adjust front/rear
Audio Adjustments
speaker balance.
Each time you touch a or b it moves the
front/rear speaker balance towards the front or
the rear.
Introduction of audio adjustments
FRONT:15 to REAR:15 is displayed as the
front/rear speaker balance moves from front to
rear.
#
FR: 0 is the proper setting when only two
speakers are used.
When the rear output setting is S.W, you can-
#
not adjust front/rear speaker balance. Refer to
1
1 Audio display
3
Touch c or d to adjust left/right speak-
Shows the audio adjustment status.
er balance.
Each time you touch c or d it moves the left/
right speaker balance towards the left or the
right.
LEFT:15 to RIGHT:15 is displayed as the left/
right speaker balance moves from left to right.
Important
If the multi-channel processor (DEQ-P8000) is
connected to this unit, the audio function will be
changed to the multi-channel processor’s audio
menu. For details, refer to Introduction of DSP ad-
Using the equalizer
The equalizer lets you adjust the equalization
to match the car’s interior acoustic character-
istics as desired.
1
Touch AV MENU and then touch
AUDIO MENU to display the audio function
names.
The audio function names are displayed and
operable ones are highlighted.
#
To go to the next group of function names,
Recalling equalizer curves
touch NEXT.
There are six stored equalizer curves which
you can easily recall at any time. Here is a list
of the equalizer curves.
#
To return to the previous group of function
names, touch PREV.
#
When selecting FM and Bluetooth telephone
as the source, you cannot switch to SLA.
Display
POWERFUL
NATURAL
VOCAL
Equalizer curve
Powerful
Natural
2
Touch ESC to return to the ordinary dis-
play.
#
To return to the previous display, touch BACK.
Vocal
Using balance adjustment
You can change the fader/balance setting so
that it can provide the ideal listening environ-
ment in all occupied seats.
CUSTOM
FLAT
Custom
Flat
SUPER BASS Super bass
1
Touch FADER/BALANCE on the audio
function menu.
When the rear output setting is S.W,
!
CUSTOM is an adjusted equalizer curve
that you create. If you make adjustments to
an equalizer curve, the equalizer curve set-
ting is memorized in CUSTOM.
#
BALANCE will be displayed instead of
32
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
!
When FLAT is selected, no supplement or
correction is made to the sound. This is
useful to check the effect of the equalizer
curves by switching alternatively between
FLAT and a set equalizer curve.
6
Touch a or b to adjust the level of the
equalizer band.
+12dB to -12dB is displayed as the level is in-
creased or decreased.
#
You can then select another band and adjust
the level.
%
Press EQ to select the equalizer.
Press EQ repeatedly to switch between the fol-
lowing equalizers:
Adjusting loudness
Loudness compensates for deficiencies in the
low- and high-sound ranges at low volume.
POWERFUL—NATURAL—VOCAL—CUSTOM
—FLAT—SUPER BASS
1
Touch LOUDNESS on the audio function
Adjusting equalizer curves
menu.
You can adjust the center frequency and the Q
factor (curve characteristics) of each currently
selected curve band (LOW/MID/HIGH).
2
#
Touch d to turn loudness on.
To turn loudness off, touch c.
!
The actual range of the adjustments are dif-
ferent depending on which equalizer curve
is selected.
3
Touch c or d to select a desired level.
LOW (low)—MID (mid)—HIGH (high)
Using subwoofer output
This unit is equipped with a subwoofer output
which can be turned on or off.
Level (dB)
Q=2W
Q=2N
!
When the subwoofer output is on, you can
adjust the cut-off frequency and the output
level of the subwoofer.
Center frequency
Frequency (Hz)
1
Touch SUB WOOFER on the audio func-
1
Touch PARAMETRIC EQ on the audio
tion menu.
function menu.
2
Touch d next to SUB WOOFER to turn
2
Touch c or d next to EQ SELECT to se-
subwoofer output on.
lect an equalizer curve.
#
To turn subwoofer output off, touch c.
POWERFUL—NATURAL—VOCAL—CUSTOM
—FLAT—SUPER BASS
3
Touch c or d next to PHASE to select
the phase of subwoofer output.
Touch d to select normal phase and
NORMAL appears in the display. Touch c to
select reverse phase and REVERSE appears in
the display.
3
Touch c or d next to BAND to select
the equalizer band to adjust.
LOW (low)—MID (mid)—HIGH (high)
4
Touch c or d next to FREQUENCY to se-
lect the frequency to adjust.
4
Touch c or d next to LEVEL to adjust
Low: 40Hz—80Hz—100Hz—160Hz
Mid: 200Hz—500Hz—1kHz—2kHz
High: 3.15kHz—8kHz—10kHz—12.5kHz
the output level of the subwoofer.
+6 to –24 is displayed as the level is increased
or decreased.
5
Touch c or d next to Q.FACTOR to se-
5
Touch c or d next to FREQUENCY to se-
lect the Q factor.
lect cut-off frequency.
2W—1W—1N—2N
Each time you touch c or d selects cut-off fre-
quencies in the following order:
50Hz—63Hz—80Hz—100Hz—125Hz
33
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
Only frequencies lower than those in the se-
lected range are outputted from the subwoo-
fer.
3
4
Touch SLA.
Touch c or d to adjust the source vo-
lume.
Each time you touch c or d it increases or de-
creases the source volume.
+4 to –4 is displayed as the source volume is
increased or decreased.
Boosting the bass
Bass boost function boosts the bass level of
sound.
Notes
1
Touch BASS BOOSTER on the audio
function menu.
!
!
The AM volume level can also be adjusted
with source level adjustments.
Video CD, CD, compressed audio and DivX
are set to the same source level adjustment
volume automatically.
2
Touch c or d to select a desired level.
0 to +6 is displayed as the level is increased or
decreased.
!
External unit 1 and external unit 2 are set to
the same source level adjustment volume
automatically.
Using the high pass filter
When you do not want low sounds from the
subwoofer output frequency range to play
from the front or rear speakers, turn on the
HPF (high pass filter). Only frequencies higher
than those in the selected range are output
from the front or rear speakers.
1
Touch HPF on the audio function menu.
2
Touch d next to HPF to turn high pass
filter on.
#
To turn high pass filter off, touch c.
3
Touch c or d next to FREQUENCY to se-
lect cut-off frequency.
Each time you touch c or d selects cut-off fre-
quencies in the following order:
50Hz—63Hz—80Hz—100Hz—125Hz
Only frequencies higher than those in the se-
lected range are outputted from the front or
rear speakers.
Adjusting source levels
SLA (source level adjustment) lets you adjust
the volume level of each source to prevent ra-
dical changes in volume when switching be-
tween sources.
!
Settings are based on the FM volume level,
which remains unchanged.
1
Compare the FM volume level with the
level of the source you wish to adjust.
2
Touch NEXT on the audio function
menu.
34
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
Setting up the DVD player
Notes
!
!
If the selected language is not recorded on
the disc, the language specified on the disc is
displayed.
You can also switch the subtitle language by
touching SUBTITLE during playback. (Refer to
Introduction of DVD setup
adjustments
You can use this menu to change audio, subti-
tle, parental lock and other DVD settings.
!
Even if you use SUBTITLE during playback to
switch the subtitle language, this does not af-
fect the settings here.
When you select OTHERS
When you select OTHERS, a language code
input display is shown. Refer to Language code
code of the desired language.
1
1 DVD setup menu display
Shows the DVD setup menu names.
1
Touch 0 to 9 to input the language
1
Touch g.
code.
SETUP will be displayed instead of MENU.
#
To cancel the inputted numbers, touch C.
Touch ENTER.
2
Touch SETUP.
The DVD setup function names are displayed.
To go to the next group of function names,
touch NEXT.
2
#
Setting the audio language
You can set the preferred audio language.
#
To return to the previous group of function
names, touch PREV.
1
Touch AUDIO LANGUAGE on the DVD
3
Touch ESC to return to the playback dis-
setup menu.
play.
An audio language menu is displayed.
#
To return to the previous display, touch BACK.
2
Touch the desired language.
The audio language is set.
To switch to the second language select
menu, touch NEXT.
To return to the first language select menu,
touch PREV.
Setting the subtitle language
#
You can set a desired subtitle language. If the
selected subtitle language is recorded on the
DVD, subtitles are displayed in that language.
#
#
1
Touch SUB TITLE LANGUAGE on the
DVD setup menu.
A subtitle language menu is displayed.
Notes
2
Touch the desired language.
A subtitle language is set.
To switch to the second language select
menu, touch NEXT.
To return to the first language select menu,
touch PREV.
!
!
If the selected language is not recorded on
the disc, the language specified on the disc is
outputted.
You can also switch the audio language by
touching AUDIO during playback. (Refer to
#
#
#
35
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
!
Even if you use AUDIO during playback to
switch the audio language, this does not af-
fect the settings here.
Setting the aspect ratio
There are two kinds of display. A wide screen
display has a width-to-height ratio (TV aspect)
of 16:9, while a regular display has a TV aspect
of 4:3. Be sure to select the correct TV aspect
for the display connected to REAR MONITOR
OUTPUT.
Setting the menu language
You can set the preferred language for dis-
plays of menus recorded on a disc.
!
When using a regular display, select either
LETTER BOX or PAN SCAN. Selecting
16 : 9 may result in an unnatural picture.
If you select the TV aspect, the unit’s dis-
play changes to the same setting.
1
Touch MENU LANGUAGE on the DVD
setup menu.
!
A menu language menu is displayed.
2
Touch the desired language.
The menu language is set.
To switch to the second language select
menu, touch NEXT.
To return to the first language select menu,
touch PREV.
%
Touch TV ASPECT on the DVD setup
menu to select the TV aspect.
#
Touch TV ASPECT repeatedly until the desired
TV aspect appears in the display.
#
!
16 : 9 – Wide screen picture (16:9) is dis-
played as it is (initial setting)
#
!
LETTER BOX – The picture is the shape of a
letterbox with black bands at the top and
bottom of the screen
Note
!
PAN SCAN – The picture is cut short at the
right and left of the screen
If the selected language is not recorded on the
disc, the language specified on the disc is dis-
played.
Notes
!
!
When playing discs that do not specify
PAN SCAN, playback is with LETTER BOX
even if you select PAN SCAN setting. Confirm
whether the disc package bears the
mark. (See page 13.)
Some discs do not enable changing of the TV
aspect. For details, refer to the disc’s instruc-
tions.
Switching the assist subtitle on
or off
If assist subtitles are recorded on a DVD disc,
you can display them by turning the assist
subtitle function on.
16 : 9 LB
You can turn assist subtitles on or off as de-
sired.
%
Touch ASSIST SUBTITLE on the DVD
setup menu to turn assist subtitles on.
To turn the assist subtitle off, touch
Setting the parental lock
Some DVD video discs let you use parental
lock to restrict children from viewing violent
and adult-oriented scenes. You can set the par-
ental lock to your desired level.
#
ASSIST SUBTITLE again.
!
When you set a parental lock level and then
play a disc featuring parental lock, code
number input indications may be dis-
played. In this case, playback will begin
when the correct code number is input.
Setting the angle icon display
You can set it up so that the angle icon ap-
pears on scenes where the angle can be
switched.
!
Initially, this function is set to on.
%
Touch MULTI ANGLE on the DVD setup
Setting the code number and level
You need to have registered a code number for
playing back discs with parantal lock.
menu to turn angle icon display on.
#
To turn the angle icon display off, touch
MULTI ANGLE again.
36
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
#
If you input an incorrect code number, the
icon is displayed. Touch C and input the cor-
1
2
3
Touch NEXT on the DVD setup menu.
Touch PARENTAL.
rect code number.
#
Touch 0 to 9 to input a four digit code
number.
#
To cancel the inputted numbers, touch C.
5
Touch any of 1 to 8 to select the desired
level.
4
Touch ENTER.
The new parental lock level is set.
The code number is set, and you can now set
the level.
If you forget your code number
5
Touch any of 1 to 8 to select the desired
level.
touch C 10 times. The registered code number
is canceled, letting you register a new one.
The parental lock level is set.
!
!
LEVEL 8 – Playback of the entire disc is pos-
sible (initial setting)
LEVEL 7 to LEVEL 2 – Playback of discs for
children and non-adult-oriented discs is
possible
LEVEL 1 – Playback of discs for children
only is possible
Setting the DivX subtitle file
You can select whether to display DivX exter-
nal subtitles or not.
!
!
The DivX subtitles will be displayed even
when CUSTOM is selected if no DivX exter-
nal subtitle files exist.
Notes
!
!
We recommend to keep a record of your code
number in case you forget it.
1
2
Touch NEXT on the DVD setup menu.
Touch DivX SUB TITLE to select the de-
sired subtitle setting.
The parental lock level is recorded on the disc.
Look for the level indication written at the disc
package, included literature or on the disc it-
self. Parental lock of this unit is not possible if
a parental lock level is not recorded in the
disc.
With some discs, the parental lock may be ac-
tive only on the scenes with certain levels. The
playback of those scenes will be skipped. For
details, refer to the instruction manual that
came with the discs.
!
!
ORIGINAL – Display the DivX subtitles
CUSTOM – Display the DivX external subti-
tles
Notes
!
!
!
Up to 42 characters can be displayed on one
line. If more than 42 characters are set, the
line breaks and the characters are displayed
on the next line.
Up to 126 characters can be displayed on one
screen. If more then 126 characters are set,
the excess characters will not be displayed.
Changing the level
You can change the set parental lock level.
1
2
3
Touch NEXT on the DVD setup menu.
Touch PARENTAL.
Displaying your DivX® VOD
registration code
In order to play DivX VOD (video on demand)
content on this unit, you first need to register
the unit with your DivX VOD content provider.
You do this by generating a DivX VOD registra-
tion code, which you submit to your provider.
Touch 0 to 9 to input the registered
code number.
4
Touch ENTER.
This enters the code number, and you can now
change the level.
1
Touch NEXT on the DVD setup menu.
37
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
2
Touch DivX VOD.
Initial Settings
Adjusting initial settings
Using the initial settings, you can customize
various system settings to achieve optimal per-
formance from this unit.
Your 8-digit registration code is displayed.
!
Make a note of the code as you will need it
when you register with a DivX VOD provider.
Setting for digital output
Audio which is outputted from digital output
of this unit can be selected. Normally, set to
STREAM. If this unit’s digital output is not
used, there is no need to change settings.
!
Selecting Linear PCM enables you to
switch the output channel if playing the fol-
lowing type of discs. (Refer to Selecting
— Dual mono mode DVD video discs
1
1
2
Touch NEXT on the DVD setup menu.
1 Function display
Shows the function names.
Touch DIGITAL OUTPUT to select the de-
sired digital output setting.
1
Touch the source icon and then touch
!
STREAM – The Dolby Digital/DTS signal is
output as it is (initial setting)
Linear PCM – The Dolby Digital/DTS signal
is converted to and output as a linear PCM
signal
OFF to turn this unit off.
2
Touch the screen to display the touch
!
panel keys.
3
Touch AV MENU and then touch
INITIAL MENU to display the function
names.
The function names are displayed and oper-
able ones are highlighted.
#
To go to the next group of function names,
touch NEXT.
#
To return to the previous group of function
names, touch PREV.
4
Touch ESC to return to the ordinary dis-
play.
#
To return to the previous display, touch BACK.
Switching the auxiliary setting
Auxiliary devices connected to this unit can be
activated individually. Set each AUX source to
ON when using. For more information about
connecting or using auxiliary devices, refer to
38
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
3
Touch c or d next to PREOUT to switch
Switching the auxiliary 1 setting
the subwoofer output or rear output.
Touching c or d will switch between S.W and
REAR and that status will be displayed.
%
Touch AUX1 on the initial menu to se-
lect desired setting.
!
VIDEO – an iPod with video capabilities
connected with 4-pole mini plug cable (e.g.,
CD-V150M)
Notes
!
!
AUDIO – auxiliary device connected with
stereo mini plug cable
OFF – No auxiliary device is connected
!
Even if you change this setting, there is no
output unless you turn the subwoofer output
!
!
If you change this setting, subwoofer output
in the audio menu return to the factory set-
tings.
Both rear speaker lead outputs and RCA rear
output are switched simultaneously in this
setting.
Switching the auxiliary 2 setting
Touch AUX2 on the initial menu to turn
auxiliary 2 setting on.
To turn auxiliary 2 setting off, touch AUX2
%
#
again.
Setting the rear output and
subwoofer controller
Changing languages for CAUTION
Some operations on this unit are prohibited
while driving or needs to be paid a careful at-
tention when operating. In such case, a cau-
tion appears on the display. You can change
the language of the cautions at this setting.
This unit’s rear output (rear speaker leads out-
put and RCA rear output) can be used for full-
range speaker (FULL) or subwoofer (S.W) con-
nection. If you switch the rear output setting
to S.W, you can connect a rear speaker lead
directly to a subwoofer without using an auxili-
ary amp.
Initially, the unit is set for rear full-range speak-
er connection (FULL). When rear output is
connected to full range speakers (when FULL
is selected), you can connect other full range
speakers (REAR) or a subwoofer (S.W) to the
RCA rear output.
%
Touch CAUTION LANGUAGE on the in-
itial menu to select your desired language.
Each time you touch CAUTION LANGUAGE it
selects languages for CAUTION in the follow-
ing order:
ENGLISH—ESPAÑOL—FRANÇAIS
Switching the sound muting/
attenuation
Sound from this system is muted or attenu-
ated automatically when the signal from the
equipment with mute function is received.
!
When the multi-channel processor (e.g.,
DEQ-P8000) is connected to this unit, you
cannot operate this function.
1
2
Touch REAR SP on the initial menu.
!
Sound from this system returns to normal
when the muting or attenuation is can-
celed.
Touch c or d next to REAR SP to switch
the rear output setting.
Touch c to select full-range speaker and FULL
appears in the display. Touch d to select sub-
woofer and S.W appears in the display.
%
Touch TEL to select any of the muting,
attenuation or off.
#
When no subwoofer is connected to the rear
output, select FULL (full-range speaker).
When a subwoofer is connected to the rear
output, select S.W (subwoofer).
When the rear output setting is S.W, you can-
not operate the following procedure.
Touch TEL until the desired setting appears in
the display.
#
!
!
MUTE – Muting
ATT-20dB – Attenuation (ATT-20dB has a
stronger effect than ATT-10dB)
ATT-10dB – Attenuation
#
!
39
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
!
OFF – Turn the sound muting/attenuation
off
!
Only when the multi-channel processor
(e.g., DEQ-P8000) is connected to this unit,
you can operate this function.
Notes
1
2
Touch NEXT on the initial menu.
!
!
The sound is turned off, MUTE is displayed
and no audio adjustments are possible.
The sound is attenuated, ATT is displayed and
no audio adjustments, except volume control,
are possible.
Operation returns to normal when the phone
connection is ended.
Touch DIGITAL ATT to switch the digital
attenuator setting.
Touch DIGITAL ATT repeatedly until the de-
sired setting appears in the display.
!
!
HIGH – High quality sound
LOW – Minimize distortion sound
!
Resetting the audio functions
You can reset all audio functions except vo-
lume.
Entering PIN code for Bluetooth
wireless connection
To connect your cellular phone to this unit via
Bluetooth wireless technology, you need to
enter PIN code on your phone to verify the
connection. The default code is 0000, but you
can change this in this function.
!
Only when the multi-channel processor
(e.g., DEQ-P8000) is connected to this unit,
you can operate this function.
1
2
3
4
Touch NEXT on the initial menu.
Touch AUDIO RESET.
!
With some Bluetooth audio players, you
may be required to enter the Bluetooth
audio player PIN code in advance to set
this unit for a connection.
You can only operate this function when
Bluetooth adapter (e.g. CD-BTB200) is con-
nected to this unit.
Touch RESET.
Touch RESET again to reset audio func-
!
tions.
#
To cancel resetting the audio functions, touch
CANCEL.
1
2
Touch NEXT on the initial menu.
Touch PINCODE INPUT.
PIN code input display appears.
3
Touch 0 to 9 to input the PIN code of
your Bluetooth audio player.
#
To cancel the inputted numbers, touch C.
4
After inputting PIN code (up to 16 di-
gits), touch ENTER.
The PIN code you entered is stored in this sys-
tem.
Correcting distorted sound
You can minimize distortion that may be
caused by the equalizer curve settings.
Setting an equalizer level high can cause dis-
tortion. If high sound is crippled or distorted,
try switching to LOW. Normally, leave the set-
ting at HIGH to ensure quality sound.
40
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
Other Functions
Introduction of system
adjustments
03
JUST (just)
The picture is enlarged slightly at the center and
the amount of enlargement increases horizontally
to the ends, enabling you to enjoy a 4:3 picture
without sensing any disparity even on a wide
screen.
CINEMA (cinema)
The picture is enlarged by the same proportion as
FULL or ZOOM in the horizontal direction and by
an intermediate proportion between FULL and
ZOOM in the vertical direction; ideal for a cine-
ma-sized picture (wide screen picture) where cap-
tions lie outside.
1
1 System menu display
ZOOM (zoom)
Shows the system function names.
A 4:3 picture is enlarged in the same proportion
both vertically and horizontally; ideal for a cine-
ma-sized picture (wide screen picture).
1
Touch AV MENU and then touch
SYSTEM MENU to display the system func-
tion names.
The system function names are displayed and
operable ones are highlighted.
NORMAL (normal)
A 4:3 picture is displayed as it is, giving you no
sense of disparity since its proportions are the
same as that of the normal picture.
#
To go to the next group of function names,
touch NEXT.
#
To return to the previous group of function
Notes
names, touch PREV.
!
!
Different settings can be memorized for each
video source.
When video is viewed in a wide screen mode
that does not match its original aspect ratio, it
may appear different.
2
Touch ESC to return to the display of
each source.
To return to the previous display, touch BACK.
#
!
!
Remember that using the wide mode feature
of this system for commercial or public view-
ing purposes may constitute an infringement
on the author’s rights protected by the Copy-
right Law.
Changing the wide screen mode
You can select a desired mode for enlarging a
4:3 picture to a 16:9 one.
1
Touch WIDE MODE on the system
The video image will appear coarser when
viewed in CINEMA or ZOOM mode.
menu.
2
3
Touch the desired wide mode setting.
Touch ESC to hide the touch panel keys.
Changing the picture adjustment
FULL (full)
You can adjust BRIGHTNESS (brightness),
CONTRAST (contrast), COLOR (color) and
HUE (hue) for each source and rear view cam-
era.
A 4:3 picture is enlarged in the horizontal direc-
tion only, giving you a 4:3 TV picture (normal pic-
ture) without any omissions.
!
You cannot adjust COLOR or HUE for the
audio source.
41
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
1
Touch PICTURE ADJUSTMENT on the
Selecting the background display
You can switch background displays while lis-
tening to each source.
system menu.
The adjustment function names are displayed.
!
You can enjoy AV (AV input) as the back-
ground video image while you are listening
to audio source such as radio or CD.
2
Touch any of the following touch panel
keys to select the function to be adjusted.
!
!
!
!
BRIGHTNESS – Adjust the black intensity
CONTRAST – Adjust the contrast
COLOR – Adjust the color saturation
HUE – Adjust the tone of color (red is em-
phasized or green is emphasized)
DIMMER – Adjust the brightness of display
REAR VIEW/SOURCE – Switch the picture
adjustment modes
%
Touch BACKGROUND on the system
menu to select the desired background dis-
play.
Audio source
!
!
BGP1 (background picture 1)—BGP2 (back-
ground picture 2)—BGP3 (background picture
3)—AV (AV input)
#
You cannot adjust the picture adjustment for
Video source
rear view camera when CAMERA POLARITY is
OFF (off)—BGP1 (background picture 1)—
BGP2 (background picture 2)—BGP3 (back-
ground picture 3)—AV (AV input)
#
With some rear view cameras, picture adjust-
#
When the AV (AV input) is not set to VIDEO,
ment may not be possible.
3
Touch c or d to adjust the selected
item.
Setting the AV input
You can switch the setting according to the
connected component.
Each time you touch c or d it increases or de-
creases the level of selected item. +24 to –24
is displayed as the level is increased or de-
creased.
!
!
!
!
Select VIDEO to watch video of a con-
nected component as AV source.
Select S-DVD to watch video of a con-
nected DVD player as S-DVD source.
Select EXT-VIDEO to watch video of a con-
nected video unit as EXT source.
4
Touch ESC to hide the touch panel keys.
Adjusting the dimmer
To prevent the display from being too bright at
night, the display is automatically dimmed
when the car’s headlights are turned on. You
can turn the dimmer on or off.
Select TV to watch TV pictures from a con-
nected TV tuner as TV source.
%
Touch AV INPUT on the system menu to
select the AV input setting.
1
Touch PICTURE ADJUSTMENT on the
!
!
OFF – No video component connected
VIDEO – External video component (such
as portable video player)
system menu.
The adjustment function names are displayed.
!
!
!
S-DVD – DVD player connected with RCA
cable
EXT-VIDEO – External video unit (such as
Pioneer products available in the future)
TV – TV tuner connected with RCA cable
2
Touch DIMMER.
3
Touch c or d to adjust the brightness.
Each time you touch c or d it moves cursor
towards the left or the right.
The level indicates the brightness of the
screen being adjusted. The farther cursor
moves to the right, the brighter the screen.
4
Touch ESC to hide the touch panel keys.
42
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
and confirm if a rear view camera video
can be shown on the display.
If the display should be switched to a rear
view camera video by error while you are
driving forward, change the rear view cam-
era setting.
To end watching a rear view camera video
and return to the source display, press and
hold VOLUME/MUTE.
Even while driving, rear view camera image
can be displayed. To do this, touch
REARVIEW source icon. In this case, touch
REARVIEW again to turn off the rear view
camera. For details, refer to Selecting a
Setting the clock
Use these instructions to set the clock.
!
1
Touch CLOCK ADJ on the system menu.
Touch ON/OFF to turn the clock display
2
on.
!
!
#
To turn the clock display off, touch ON/OFF
again.
3
Touch c or d to select the segment of
the clock display you wish to set.
Each time you touch c or d it will select one
segment of the clock display:
Hour—Minute
As you select segments of the clock display
the segment selected will be highlighted.
%
Touch CAMERA POLARITY on the sys-
tem menu to select an appropriate setting.
4
Touch a or b to put a clock right.
!
!
!
BATTERY – When the polarity of the con-
nected lead is positive while the gear shift
is in REVERSE (R) position
GROUND – When the polarity of the con-
nected lead is negative while the gear shift
is in REVERSE (R) position
Notes
!
You can match the clock to a time signal by
touching JUST.
— If 00 to 29, the minutes are rounded down.
(e.g., 10:18 becomes 10:00.)
— If 30 to 59, the minutes are rounded up.
(e.g., 10:36 becomes 11:00.)
OFF – When a rear view camera is not con-
nected to this unit
!
Even when the sources are off, the clock dis-
play appears on the display.
Switching the iPod charge setting
You can turn the iPod charge setting on or off
while listening to an iPod.
Setting for rear view camera
(back up camera)
!
Listening AM radio while an iPod is
charged from this unit may generate noise.
In this case, turn the iPod charge setting
off and noise is disappeared.
CAUTION
Pioneer recommends the use of a camera
which outputs mirror reversed images, other-
wise screen image may appear reversed.
!
1
2
Initially, this function is set to on.
Touch NEXT on the system menu.
This unit features a function that automatically
switches to the rear view camera video (REAR
CAMERA IN jack) when a rear view camera is
installed on your vehicle. When the gear shift
is in REVERSE (R) position, the video auto-
matically switches to a rear view camera
Touch iPod CHARGE to turn the iPod
charge setting on.
To turn the iPod charge setting off, touch
#
iPod CHARGE again.
Note
video. (For more details, consult your dealer.)
For maximum performance, we recommend that
you use the latest version of the iPod software.
!
After you set up the rear view camera set-
ting, move the gear shift in REVERSE (R)
43
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
4
To store the customized color in mem-
ory, touch and hold one of preset keys
) 1 to 3 until the beep sounds.
Selecting the OSD color
You can change the OSD color.
(
The customized color has been stored in mem-
ory.
%
color.
Touch OSD COLOR to select the desired
The next time you touch the same preset key,
the color is recalled from memory.
Each time you touch OSD COLOR it selects
colors in the following order:
BLUE (blue)—RED (red)—AMBER (amber)—
GREEN (green)—VIOLET (violet)
Adjusting the response
positions of the touch panels
(Touch Panel Calibration)
Selecting the illumination color
This unit is equipped with multiple-color illu-
mination. You can select a desired color from
112 different types of color.
If you feel that the touch panel keys on the
screen deviate from the actual positions that
respond to your touch, adjust the response po-
sitions of the touch panel. There are two ad-
justment methods: 4-point adjustment, in
which you touch four corners of the screen;
and 16-point adjustment, in which you make
fine-adjustments on the entire screen.
Direct selection from preset
illumination color
You can select an illumination color from the
color list.
!
Make sure to use the supplied pen for ad-
justment, and gently touch the screen. If
you press the touch panel forcefully, the
touch panel may be damaged. Do not use
a sharp pointed tool such as ballpoint pen
or a mechanical pen. Otherwise the screen
is damaged.
1
Touch ILLUMI COLOR to display the set-
ting menu.
2
Touch one of the color list.
You can select one from the following list.
!
!
!
!
!
!
BLUE (blue)
RED (red)
AMBER (amber)
GREEN (green)
VIOLET (violet)
SCAN (scanning all colors)
!
If touch panel adjustment cannot be per-
formed properly, consult your local Pioneer
dealer.
1
Touch the source icon and then touch
OFF to turn this unit off.
When the source icon is not displayed, you
can display it by touching the screen.
#
Note
SCAN setting cycles continuously through all the
colors.
2
Press and hold h (eject).
The 4-point touch panel adjustment screen ap-
pears.
Customizing the illumination color
1
Touch ILLUMI COLOR to display the set-
3
Touch each of the arrows on the four
ting menu.
corners of the screen with the touch panel
adjustment pen.
#
2
Touch
to display the customizing
To cancel the adjustment, press and hold
menu.
VOLUME/MUTE.
3
Rotate VOLUME/MUTE to customize
the color.
44
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
4
Press EQ to complete the 4-point ad-
!
It is possible to connect a portable audio/
video player by using a 3.5 mm plug (4
pole) to RCA cable, which is sold sepa-
rately. However, depending on the cable, re-
verse connection between Red (right side
audio) cable and yellow (video) cable is re-
quired. Otherwise, audio and video may not
be correctly reproduced.
justment.
The adjusted position data is saved.
#
Do not turn off the engine while saving the ad-
justed position data.
5
Press EQ to proceed to the 16-point ad-
justment.
The 16-point touch panel adjustment screen
appears.
%
Insert the stereo mini plug into the
#
To cancel the adjustment, press and hold
AUX input jack on this unit.
VOLUME/MUTE.
6
Gently touch the center of the + mark
displayed on the screen with the touch
panel adjustment pen.
After you touch all the marks, the adjusted po-
sition data is saved.
IP-BUS-RCA interconnector (AUX 2)
When connecting auxiliary device using an IP-
BUS-RCA Interconnector (sold separately)
#
Do not turn off the engine while saving the ad-
%
Use an IP-BUS-RCA Interconnector such
justed position data.
as the CD-RB20/CD-RB10 (sold separetely)
to connect this unit to auxiliary device fea-
turing RCA output.
For more details, refer to the IP-BUS-RCA Inter-
connector owner’s manual.
7
Press and hold VOLUME/MUTE to com-
plete the adjustment.
Using the AUX source
#
You can only make this type of connection if
the auxiliary device has RCA outputs.
A separately sold auxiliary device such as VCR
or portable device can be connected to this
unit. When connected, auxiliary device is auto-
matically recognized as AUX source and as-
signed to AUX.
Selecting AUX as the source
%
Touch the source icon and then touch
AUX 1/AUX 2 to select AUX as the source.
If the auxiliary setting is not turned on, AUX
#
About AUX connection method
cannot be selected. For more details, see Switch-
You have two methods to connect auxiliary de-
vice to this unit.
Setting the AUX title
The title displayed for the AUX source can be
Mini pin plug cable (AUX 1)
When connecting auxiliary device using a mini
plug cable
iPod and portable audio/video player can be
connected to this unit via mini plug cable.
changed.
!
Each title can be up to 10 characters long.
1
After you have selected AUX as the
source, touch AV MENU and
FUNCTION MENU and then touch
NAME EDIT.
!
If an iPod with video capabilities is con-
nected to this unit via 3.5 mm plug (4 pole)
cable (e.g., CD-V150M), you can enjoy the
video contents of the iPod.
#
When the touch panel keys are not displayed,
you can display them by touching the screen.
45
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
03
Operating this unit
2
Touch ABC to select the desired charac-
%
%
%
%
%
Touch BAND.
ter type.
Keep touching BAND.
Touch c or d.
Touch ABC repeatedly to switch between the
following character types:
Alphabet (upper case)—Alphabet (lower case)
#
You can select to input numbers and symbols
Keep touching c or d.
Touch a or b.
by touching 123.
3
Touch a or b to select a letter of the al-
phabet.
Using the functions allocated to 1 to
6 keys
4
Touch d to move the cursor to the next
character position.
1
Touch NEXT.
5
Touch OK to store the entered title in
2
Touch any of 1 to 6 to select a function.
memory.
Advanced operations
Touch AV MENU and then touch
6
play.
Touch ESC to return to the ordinary dis-
1
FUNCTION MENU to display the function
names.
The function names are displayed and oper-
able ones are highlighted.
Using the external unit
External unit refers to a Pioneer product (such
as ones available in the future) that, although
incompatible as a source, enables control of
basic functions with this unit. Two external
units can be controlled with this unit. When
two external units are connected, the external
unit is automatically allocated to external unit
1 or external unit 2 by this unit.
!
!
!
!
!
FUNC1 (function 1)
FUNC2 (function 2)
FUNC3 (function 3)
FUNC4 (function 4)
AUTO/MANUAL (auto/manual)
2
Touch ESC to return to the ordinary dis-
Basic operations of the external unit are ex-
plained below. Allocated functions are differ-
ent depending on the connected external unit.
For details concerning functions, refer to exter-
nal unit’s owner’s manual.
play.
#
To return to the previous display, touch BACK.
Using the PGM button
You can operate the preprogrammed functions
for each source by using PGM.
Selecting the external unit as the source
!
Only the optional remote control (e.g., CD-
R55) can operate this function.
%
Touch the source icon and then touch
EXT 1/EXT 2 to select external unit as the
%
Press PGM to turn pause on when se-
source.
lecting the following sources:
!
!
!
DVD – Built-in DVD player
iPod – iPod
USB – USB portable audio player/USB
memory
S-DVD – DVD player/multi-DVD player
MCD – Multi-CD player
Basic operation
Functions allocated to the following opera-
tions are different depending on the con-
nected external unit. For details concerning
functions, refer to the connected external
unit’s owner’s manual.
!
!
46
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Operating this unit
03
!
BT Audio – Bluetooth audio player
#
To turn pause off, press PGM again.
%
Press PGM and hold to turn BSM on
when selecting RADIO as the source.
Press PGM and hold until the BSM turns on.
#
To cancel the storage process, press PGM
again.
%
Press PGM and hold to turn BSSM on
when selecting TV as the source.
Press PGM and hold until the BSSM turns on.
#
To cancel the storage process, press PGM
again.
%
Press PGM to select the desired channel
select setting when selecting XM or SIRIUS
as the source.
Press PGM repeatedly to switch between the
following channel select settings:
CH-NUMBER (channel number select setting)
—CATEGORY (channel category select
setting)
47
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
3
Touch c or d to select a desired
XM tuner
Basic Operations
You can use this unit to control an XM satellite
digital tuner (GEX-P920XM), which is sold
separately.
channel.
The channels move up or down step by step.
Channels that cannot currently be selected
are skipped, and the next channel is selected.
#
If you touch and hold c or d, you can in-
crease or decrease the channel number con-
tinuously.
For details concerning operation, refer to the
XM tuner’s operation manuals. This section
provides information on XM operations with
this unit which differs from that described in
the XM tuner’s operation manual.
#
You can also perform tuning from a desired
channel category. (Refer to Selecting a channel in
!
This unit does not have the text scroll
function.
Storing and recalling broadcast
stations
You can easily store up to six broadcast sta-
tions for later recall.
!
With this unit, you can operate one addi-
tional function: XM channel direct
selection.
1 2 3
4
5
6
!
Up to 18 stations, six for each of three XM
bands can be stored in memory.
1
Select the channel that you want to
store in memory.
2
3
Touch LIST to display the preset list.
Touch and hold a preset tuning key
P1 (PRESET1) to P6 (PRESET6) until the beep
sounds.
The selected station has been stored in mem-
ory.
The next time you touch the same preset tun-
ing key P1 (PRESET1) to P6 (PRESET6) the sta-
tion is recalled from memory.
7
1 Source icon
2 XM band indicator
3 XM channel category
4 XM channel select setting indicator
Shows what channel select setting has been
selected.
5 XM preset number indicator
6 XM channel number indicator
7 Detail information
4
Touch ESC to return to the ordinary dis-
play.
Note
Shows the detail information of the broadcast
channel currently being received.
You can also use a and b to recall stations as-
signed to preset tuning keys P1 (PRESET1) to
P6 (PRESET6) when the CH-NUMBER mode is
selected.
1
Touch the source icon and then touch
XM to select the XM.
2
Touch BAND to select an XM band.
Touch BAND repeatedly until the desired XM
band is displayed, XM1, XM2 or XM3.
#
To switch between groups of touch panel keys,
touch NEXT or PREV.
48
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
1
Touch
.
Switching the XM channel
select mode
You have two methods for selecting a channel:
by number and by category. When selecting
by number, channels in any category can be
selected. Select by category to narrow your
search down to only channels in a particular
category.
XM channel list appears in the display.
Each touch of changes the following set-
tings as follows:
CHANNEL NAME LIST (channel name)—
SONG TITLE LIST (song title)—
ARTIST NAME LIST (artist name)
2
Touch the desired channel that you
want to listen to.
To switch between the lists of names/titles,
touch or
When the CATEGORY mode is selected,
%
Touch MODE to select the desired chan-
#
nel select mode.
.
Touch MODE repeatedly to switch between
the following channel select modes:
CH-NUMBER (channel number select setting)
—CATEGORY (channel category select
setting)
#
touch a or b to switch to another category.
Selecting an XM channel directly
You can select an XM channel directly by en-
tering the desired channel number.
Selecting a channel in the channel
category
1
Touch DIRECT.
1
Touch MODE to select the channel cate-
#
To switch between groups of touch panel keys,
gory select mode.
touch NEXT or PREV.
Touch MODE repeatedly to switch between
the following channel select modes:
CH-NUMBER (channel number select setting)
—CATEGORY (channel category select
setting)
2
Touch 0 to 9 to input the desired chan-
nel number.
#
To cancel the input numbers, touch C.
3
Touch ENTER.
2
Touch a or b to select the desired chan-
The XM channel of entered number is
selected.
nel category.
3
Touch c or d to select the desired chan-
Using the MyMix function
nel in the selected channel category.
The MyMix function allows you to make the
MyMix song playlist. When the song in the
MyMix playlist is being broadcast on a station
other than the one you are listening to, you
will be alerted, and you can tune to the station
to listen to that song.
Selecting a channel from the XM
channel list display
The list content can be switched so you can
search for the track you want to listen to not
only by the channel name but also by the artist
name or song title.
!
!
This function is available for GEX-P920XM.
A track itself is NOT downloaded BUT only
the song title and the artist name are mem-
orized.
!
!
This function is available for GEX-P920XM.
The channel list shows all the channels
during the CH-NUMBER mode, and the
channels included in the selected category
during the CATEGORY mode. To switch the
channel mode, touch MODE.
49
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
Making the MyMix playlist
Setting up a song alert
You can add a song that is being broadcast to
the MyMix playlist. When it is added, the song
title and its artist name is memorized to this
unit. The MyMix function will start on the song
that matches the song title and its artist name
in the MyMix playlist.
You can set up an alert on or off by each song
in the MyMix playlist. First, display the MyMix
playlist and then change each alert setting.
Set up an alert to on so you can receive the
alert when the song is broadcast, or set it up
to off to stop the alert for that song.
1
When a desired song is broadcast,
1
Touch MEMO EDIT.
The MyMix playlist is displayed.
To switch between groups of touch panel keys,
touch NEXT or PREV.
touch and hold MEMO.
The song title and artist name of the song you
are listening to are memorized, and a confir-
mation message appears.
#
2
Touch the song title that you want to
#
The song title and artist name of up to 12
set up the alert to off.
The check mark is removed, and the alert for
that song is off.
tracks can be memorized. Trying to save more
than 12 tracks will overwrite old ones.
#
You cannot memorize the song title or the ar-
tist name when “– – – – – – – –” is displayed on
the title information.
Deleting the song from the MyMix
playlist
You can delete each song in the MyMix
playlist.
#
You cannot memorize the song title or the ar-
tist name of the channel 000.
It is possible that the memorized title is not
displayed correctly.
#
1
Touch MEMO EDIT.
2
Touch OK to confirm.
The MyMix playlist is displayed.
!
To delete the song from the MyMix playlist,
refer to Deleting the song from the MyMix
2
Touch DELETE next to the song title you
want to delete.
That song will be deleted from the MyMix
playlist.
When the song in the MyMix playlist
is broadcast
As soon as the song in the MyMix playlist
starts broadcast on a different station, a mes-
sage is displayed. Touch YES to switch to that
station, and you can listen to that song.
#
To delete all the songs in the MyMix playlist,
touch DELETE ALL.
3
A message will appear asking you to
confirm to delete it. Touch YES.
To cancel the deleting, touch NO.
#
!
If you would rather not to tune to that sta-
tion, touch CANCEL.
Displaying the Radio ID
!
If an alert for the song in the MyMix playlist
is set up to off, no alert will be provided
even when the song is broadcast. Refer to
Channel number select setting
If you select CH000, the ID code is displayed.
!
If there is slight difference between the
memorized title and the title of the song
being broadcast, no alert will be provided
even though they are the same song.
%
Touch c or d to select CH000.
Channel category select setting
RADIO ID is provided as a channel category
for displaying the ID code.
50
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
%
Touch a or b to select RADIO ID from
SIRIUS Satellite Radio tuner
Basic Operations
channel category.
Display of the ID code repeats displaying
RADIO ID and the ID code one after the other.
You can use this unit to control a SIRIUS Satel-
lite Radio tuner, which is sold separately.
When the SIRIUS tuner is used together with
this unit, some operations differ slightly from
those described in the SIRIUS operation man-
ual. This manual provides information on
these points. For all other information on
using the SIRIUS tuner, please refer to the SIR-
IUS operation manual.
#
If you select another channel, display of the ID
code is canceled.
Switching the XM display
!
This function is available for GEX-P910XM.
%
Touch INFO to switch the XM display.
Channel name—Artist name/feature—Song/
!
This unit does not have the text scroll
function.
program title—Channel category
!
With this unit, you can operate one addi-
tional function: SIRIUS channel direct se-
lection. Refer to Selecting a SIRIUS channel
1 2 3
4
5
6
7
1 Source icon
2 SIRIUS band indicator
3 SIRIUS channel category
4 SIRIUS channel select setting indicator
Shows what channel select setting has been
selected.
5 SIRIUS preset number indicator
6 SIRIUS channel number indicator
7 Detail information
Shows the detail information of the broadcast
channel currently being received.
1
Touch the source icon and then touch
SIRIUS to select SIRIUS.
2
Touch BAND to select a band.
Touch BAND repeatedly until the desired SIR-
IUS band is displayed, SR1, SR2 or SR3.
51
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
#
To switch between groups of touch panel keys,
4
Touch ESC to return to the ordinary dis-
touch NEXT or PREV.
play.
3
Touch c or d to select a desired
Note
channel.
You can also use a and b to recall stations as-
signed to preset tuning keys PRESET1 to
PRESET6 when the CH-NUMBER mode is
selected.
The channels move up or down step by step.
Channels that cannot currently be selected
are skipped, and the next channel is selected.
#
If you touch and hold c or d, you can in-
crease or decrease the channel number con-
tinuously.
Selecting the SIRIUS channel
select mode
#
You can also perform tuning from a desired
channel category. (Refer to Selecting a channel in
You have two methods for selecting a channel:
by number and by category. When selecting
by number, channels in any category can be
selected. Select by category to narrow your
search down to only channels in a particular
category.
Note
It may take a few seconds before you can hear
anything while this unit acquires and processes
the satellite signal.
%
Touch MODE to select the desired chan-
nel select mode.
Storing and recalling broadcast
stations
You can easily store up to six broadcast sta-
tions for later recall.
Touch MODE repeatedly to switch between
the following channel select modes:
CH-NUMBER (channel number select setting)
—CATEGORY (channel category select
setting)
!
Up to 18 stations, six for each of three SIR-
IUS bands can be stored in memory.
Channels are stored and recalled on a
broadcast station basis. This means that if
the broadcast station you stored has been
assigned to a different channel by SIRIUS,
you can still recall the same broadcast sta-
tion (though a different channel number
may appear in the display).
!
Selecting a channel in the channel
category
Channels are organized into various program
categories, e.g. Rock, Classic, Jazz. You can
specify channels by selecting the desired
category.
1
Touch MODE to select the channel cate-
1
Select the channel that you want to
gory select mode.
store in memory.
Touch MODE repeatedly to switch between
the following channel select modes:
CH-NUMBER (channel number select setting)
—CATEGORY (channel category select
setting)
2
3
Touch LIST to display the preset list.
Touch and hold a preset tuning key
PRESET1 to PRESET6 until the beep sounds.
The selected station has been stored in mem-
ory.
The next time you touch the same preset tun-
ing key PRESET1 to PRESET6 the station is re-
called from memory.
2
Touch a or b to select the desired chan-
nel category.
3
Touch c or d to select the desired chan-
nel in the selected channel category.
52
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
#
You cannot memorize the song title or the ar-
tist name of the channel 000.
It is possible that the memorized title is not
Selecting a SIRIUS channel directly
You can select a SIRIUS channel directly by
entering the desired channel number.
#
displayed correctly.
1
Touch DIRECT.
#
To switch between groups of touch panel keys,
When the song in the MyMix playlist
is broadcast
touch NEXT or PREV.
As soon as the memorized song starts broad-
cast on a different station, a song alert is dis-
played. Touch JUMP to switch to that station,
and you can listen to that track.
2
Touch 0 to 9 to input the desired chan-
nel number.
#
To cancel the input numbers, touch C.
3
Touch ENTER.
!
If you would rather not to tune to that sta-
tion, touch STAY.
The SIRIUS channel of entered number is
selected.
!
If an alert for the song in the MyMix playlist
is set up to off, no alert will be provided
even when the song is broadcast. Refer to
If there is slight difference between the
memorized title and the title of the song
being broadcast, no alert will be provided
even though they are the same song.
Using the MyMix function
The MyMix function allows you to make the
MyMix song playlist. When the song in the
MyMix playlist is being broadcast on a station
other than the one you are listening to, you
will be alerted, and you can tune to the station
to listen to that song.
!
Turning the MyMix function on or off
!
This function is available for SIR-PNR2/SIR-
PNR2C.
A track itself is NOT downloaded BUT only
the song title and the artist name are mem-
orized.
You can turn the MyMix function off and stop
this unit to alert you for all the songs in the
MyMix playlist. To restart, turn this function
on.
!
!
The MyMix function is on at the default
setting.
Making the MyMix playlist
1
Touch MEMO EDIT.
You can add a song that is being broadcast to
the MyMix playlist. When it is added, the song
title and its artist name is memorized to this
unit. The MyMix function will start on the song
that matches the song title and its artist name
in the MyMix playlist.
The display is switched to the memo edit
mode.
#
To switch between groups of touch panel keys,
touch NEXT or PREV.
2
Touch ALERT OFF to turn the MyMix
function off.
The MyMix function is now off.
%
When a desired song is broadcast,
touch and hold MEMO.
#
To turn the MyMix function on, touch
The song title and artist name of the song you
are listening to are memorized, and a confir-
mation message appears.
ALERT ON.
#
The song title and artist name of up to 10
tracks can be memorized. When you try to save
more than 10 tracks, FULL is displayed and that
song being broadcast cannot be saved.
53
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
!
This function is available for SIR-PNR2/SIR-
PNR2C.
Setting up a song alert
You can set up an alert on or off by each song
in the MyMix playlist. First, display the MyMix
playlist and then change each alert setting.
Set up an alert to on so you can receive the
alert when the song is broadcast, or set it up
to off to stop the alert for that song.
Selecting teams for Game Alert
1
Touch TEAM SET.
2
Touch PREV or NEXT next to LEAGUE to
select a desired league.
League names are switched in the display.
1
Touch MEMO EDIT.
The display is switched to the memo edit
mode.
#
3
Touch PREV or NEXT next to TEAM to
To switch between groups of touch panel keys,
select a desired team.
Teams in the selected category are switched in
the display.
touch NEXT or PREV.
2
Touch PREV or NEXT to select the song
title that you want to turn the alert off.
4
Touch ON/OFF to store the selected
team in memory.
3
Touch ON/OFF to turn the alert off.
ON is displayed with the selected team, and
the Game Alert function will start on that
team.
The alert for the song is turned off.
Deleting the song from the MyMix
playlist
You can delete each song in the MyMix
playlist.
#
To turn the Game Alert off of the selected
team, touch ON/OFF again.
When you have already made 12 team selec-
#
tions, FULL is displayed and additional team se-
lection is not possible. In this case, first delete
the team selection and then try again.
1
Touch MEMO EDIT.
The song title in the MyMix playlist is dis-
played.
5
Repeat these steps for selecting other
teams.
#
To switch between groups of touch panel keys,
Up to 12 teams can be selected.
touch NEXT or PREV.
2
Touch PREV or NEXT to select the song
Switching the Game Alert on or off
Once you made team selections, you need to
turn the Game Alert function on.
title that you want to delete.
3
4
Touch DELETE.
!
The Game Alert function is on at the default
setting.
A message will appear asking you to
confirm to delete it. Touch YES.
The selected song is deleted.
1
2
Touch TEAM SET.
#
To cancel the deleting, touch CANCEL.
Touch ALERT ON to turn the Game Alert
on.
Using the Game Alert function
The Game Alert function is now on.
#
To turn the Game Alert function off, touch
This system can alert you when games invol-
ving your favorite teams are about to start. To
use this function you need in advance to set
up a game alert for the teams.
ALERT OFF.
54
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
%
Touch INFO to switch the SIRIUS display.
When the game of the selected team
starts
When a game of the selected team is about to
start (or is currently playing) on a different sta-
tion, a game alert is displayed. Touch JUMP to
switch to that station, and you can listen to
that game.
Channel name—Artist name/feature—Song/
program title—Channel category
Using Instant Replay function
Following functions can be operated during
the Instant Replay mode.
!
If you would rather not to tune to that sta-
tion, touch STAY.
!
To use this function, Pioneer SIRIUS bus in-
terface (e.g. CD-SB10) is required.
To use this function, SIRIUS plug-and-play
unit with Instant Replay Function is re-
quired.
Displaying game information
!
If games of your selected teams are currently
playing, you can display information of the
games and tune to the broadcast channel.
!
For details, refer to SIRIUS plug-and-play
unit’s manuals.
1
Touch GAME INFO.
The game information of your selected team is
displayed.
%
%
Touch NEXT.
Touch INSTANT REPLAY.
2
Touch PREV or NEXT to select a game.
Instant Replay mode is deiplayed. Now, Instant
The game is displayd, followed by more de-
tailed game information.
Replay mode can be performed.
#
In the following conditions, tuner exits from
!
Game score will be updated automatically.
the Instant Replay mode.
— When LIVE is touched
— When another source is selected
3
Touch TuneTO to switch to that station
to listen to the game.
%
Select a track
Notes
Touch c or d.
!
!
If you have not made any team selections,
NOT SET is displayed.
When games involving your favorite teams are
not currently playing, NO GAME is displayed.
%
Pause and play
Touch de.
%
Fast forward or reverse
Touch and hold c or d for about one second
and release.
Displaying the Radio ID
If you select CH000, the ID code is displayed.
%
#
Touch c or d to select CH000.
To select CH000, set the channel select setting
to CH-NUMBER. About the channel select set-
ting, refer to Selecting the SIRIUS channel select
Switching the SIRIUS display
!
This function is available for SIR-PNR1.
55
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
section provides brief information on Blue-
tooth audio player operations with this unit,
which slightly differs or is abbreviated from
that described in the Bluetooth adapter’s op-
eration manual.
Bluetooth Audio
Basic Operations
!
If you connect a Bluetooth adapter (e.g. CD-
BTB200) to this unit, you can control Blue-
tooth audio players via Bluetooth wireless
technology.
!
Even though your audio player does not
contain a Bluetooth module, you can still
control it from this unit via Bluetooth wire-
less technology. To control your audio
player using this unit, connect a product
featuring Bluetooth wireless technology
(available on the market) to your audio
player and connect the Bluetooth adapter
(e.g. CD-BTB200) to this unit.
!
In some countries, CD-BTB200 is not sold
on the market.
Important
!
Depending on the Bluetooth audio player con-
nected to this unit, the operations available
with this unit are limited to the following two
levels:
1
2
3
— Lower level: Only playing back songs on
your audio player is possible.
— Higher level: Playing back, pausing, select-
ing songs, etc., are possible (all the opera-
tions illustrated in this manual).
!
Since there are a number of Bluetooth audio
players available on the market, operations
with your Bluetooth audio player using this
unit vary in great range. Refer to the instruc-
tion manual that came with your Bluetooth
audio player as well as this manual while op-
erating your player on this unit.
1 Source icon
2 Device name
Shows the device name of the connected
Bluetooth audio player (or Bluetooth adapter).
3 Connection indicator
!
!
Information about songs (e.g. the elapsed
playing time, song title, song index, etc.) can-
not be displayed on this unit.
While you are listening to songs on your Blue-
tooth audio player, refrain from operating on
your cellular phone as much as possible. If
you try operating your cellular phone, the sig-
nal from your cellular phone may cause noise
on the song playback.
When you are talking on a cellular phone con-
nected to this unit via Bluetooth wireless tech-
nology, song playback from your Bluetooth
audio player connected to this unit is muted.
Even if while you are listening to a song on
your Bluetooth audio player and you switch to
another source, playback of song continues.
Shows the Bluetooth wireless connection sta-
tus.
1
Touch the source icon and then touch
BT Audio to select the Bluetooth audio
source.
#
For this unit to control your Bluetooth audio
player it needs to establish a Bluetooth wireless
connection. (Refer to Connecting a Bluetooth
!
!
2
Touch d.
Playback starts.
3
To skip back or forward to another
track, briefly touch o or p.
4
To perform fast forward or reverse,
For details concerning operation, refer to the
Bluetooth adapter’s operation manual. This
keep touching o or p.
56
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
5
To stop playback, touch g.
Disconnecting a Bluetooth
audio player
Pausing playback
%
menu.
Touch DISCONNECT on the function
%
#
Touch e during playback.
To resume playback at the same point that you
After the disconnection is completed,
NO CONNECTION is displayed.
turned pause on, touch d.
Displaying BD (Bluetooth
Device) address
Introduction of advanced
operations
%
Touch DEVICE INFO on the function
1
Touch AV MENU and then touch
menu to display the BD address.
Various information regarding the Bluetooth
wireless technology are displayed.
FUNCTION MENU to display the function
names.
The function names are displayed and oper-
able ones are highlighted.
!
DEVICE NAME (device name of this sys-
tem)
!
!
!
BD ADDRESS (address of Bluetooth device)
SYSTEM VERSION (system version)
BT MODULE VERSION (version of Blue-
tooth module)
2
play.
#
Touch ESC to return to the ordinary dis-
To return to the previous display, touch BACK.
Connecting a Bluetooth audio
player
%
Touch CONNECTION OPEN on the func-
tion menu to turn the connection open on.
CONNECTION WAITING is displayed. This
unit is now on standby for connection from
Bluetooth audio player.
If your Bluetooth audio player is set ready for
Bluetooth wireless connection, connection to
this unit is automatically established.
Note
Before you can use audio players you may need
to enter the PIN code into this unit. If your player
requires a PIN code to establish a connection,
look for the code on the player or in its accompa-
nying documentation. Refer to Entering PIN code
57
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
2 User number indicator
Bluetooth Telephone
Basic Operations
Shows the registration number of the cellular
phone.
3 Device name
Shows the device name of the cellular phone.
4 Phone number
Shows the phone number you selected.
5 Voice recognition indicator
Shows when the voice recognition function is
on (for more details, refer to Voice recognition
!
If you connect a Bluetooth adapter (e.g. CD-
BTB200) to this unit, you can control Blue-
tooth audio players via Bluetooth wireless
technology.
!
In some countries, CD-BTB200 is not sold
on the market.
Important
6 Incoming call notice indication
Shows when an incoming call has been re-
ceived and not checked yet.
!
!
Since this unit is on standby to connect with
your cellular phone via Bluetooth wireless
technology, using this unit without running
the engine can result in battery drainage.
Advanced operations that require your atten-
tion such as dialing numbers on the monitor,
using phone book, etc., are prohibited while
you are driving. When you need to use these
advanced operations, stop your vehicle in a
safe place.
!
Incoming call notice is not displayed for
calls made when your cellular phone is
disconnected from this unit.
7 Automatic answering/Automatic rejecting in-
dicator
Shows when the automatic answering func-
tion is on (for more details, refer to Setting
Shows when the automatic rejecting function
is on (for more details, refer to Setting auto-
For details concerning operation, refer to the
Bluetooth adapter’s operation manual. This
section provides brief information on the
hands-free phoning operations with this unit
which slightly differes or is cut short from that
described in the Bluetooth adapter’s operation
manual.
8 Battery strength indicator
Shows the battery strength of cellular phone.
!
Battery strength indicator may differ
from the actual battery strength.
If the battery strength is not available,
nothing is displayed in the battery
strength indicator area.
!
!
This unit is not compatible with registration
for guest phone.
This unit does not have the name edit func-
tion of a Phone Book entry.
!
9 Signal level indicator
Shows the signal strength of cellular phone.
1
2
3
4
!
Signal level indicator may differ from
the actual signal level.
!
Depending on the cellular phones fea-
turing Bluetooth wireless technology,
radio field intensity is not available. In
this case, the signal level indicator does
not appear.
!
If your cellular phone is out of service,
is displayed.
9
7
5
a Telephone indicator
a
8
6
1 Source icon
58
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
Shows when a phone connection using Blue-
tooth wireless technology is established (for
more details, refer to Connecting a cellular
level is memorized in this unit as the default
setting.
#
Caller’s voice volume and ring volume may
vary depending on the type of cellular phone.
If the difference between the ring volume and
!
While connecting automatically, tele-
phone indicator is flashing.
#
caller’s voice volume is big, overall volume level
may become unstable.
%
Touch the source icon and then touch
#
Before disconnecting the cellular phone from
TEL to select the telephone.
this unit, make sure to adjust the volume to a
proper level. If the volume is muted (zero level) on
your cellular phone, the volume level of your cel-
lular phone remains muted even after the cellular
phone is disconnected.
Note
Equalizer curve for the phone source is fixed.
When selecting the phone source, you cannot op-
erate the equalizer function. Refer to Recalling
When the multi-channel processor is connected
to this unit, you can operate the equalizer func-
tion even when selecting the phone source. Refer
Making a phone call
Voice recognition
1
Touch VOICE to turn the voice recogni-
tion function on.
Voice dial icon appears on the information bar.
Voice recognition function is now ready.
Setting up for hands-free phoning
#
To cancel the voice recognition function,
Before you can use the hands-free phoning
function you must set up the unit for use with
your cellular phone. This entails establishing a
Bluetooth wireless connection between this
unit and your phone, registering your phone
with this unit, and adjusting the volume level.
touch VOICE again.
2
Pronounce the name of your contact.
Taking a phone call
Answering an incoming call
1
Connection
For detailed instructions on connecting your
phone to this unit via Bluetooth wireless tech-
1
#
When a call comes in, touch
If private mode is selected on the cellular
.
phone, hands-free phoning may not be per-
formed.
#
Your phone should now be temporarily con-
2
To end the call, touch
.
nected. However, to make best use of the technol-
ogy, we recommend you register the phone to
this unit.
Rejecting an incoming call
When a call comes in, touch
%
.
2
Registration
The call is rejected.
To register your temporarily connected phone,
Answering a call waiting
1
Touch to answer a call waiting.
3
Volume adjustment
Adjust the earpiece volume on your cellular
phone for comfort. When adjusted, the volume
59
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
2
#
Touch to end all calls.
The caller you have been talking to is now on
name (Pioneer BT unit2) and enter the link
code on your cellular phone. If the connection
is established, CONNECTED is displayed.
hold. To end the call, both you and your caller
need to hang up the phone.
#
PIN code is set to 0000 as default. You can
#
While your callers hold the line, touching
change this code in the initial setting. Refer to En-
switches between callers.
Rejecting a call waiting
Using a cellular phone to initiate a
connection
%
Touch to reject a call waiting.
1
Touch PHONE CONNECT on the function
Introduction of advanced
operations
menu.
2
Touch CONNECTION OPEN.
1
Touch AV MENU and then touch
CONNECTION WAITING flashes and the unit
is now on standby for connection from a cellu-
lar phone.
FUNCTION MENU to display the function
names.
The function names are displayed and oper-
able ones are highlighted.
3
Use cellular phone to connect to this
unit.
2
Touch ESC to return to the telephone
standby display.
To return to the previous display, touch BACK.
#
To cancel this function, touch
CONNECTION OPEN again.
#
#
PIN code is set to 0000 as default. You can
change this code in the initial setting. Refer to En-
Connecting a cellular phone
Searching for available cellular phones
1
Touch PHONE CONNECT on the function
Disconnecting a cellular phone
menu.
1
Touch PHONE CONNECT on the function
2
Touch SEARCH to search for available
menu.
cellular phones.
While searching, SEARCHING flashes. When
available cellular phones featuring Bluetooth
wireless technology are found, device name or
Name Not Found (if names cannot be ob-
tained) is displayed.
2
Touch DISCONNECT to disconnect the
currently connected cellular phone from
this unit.
After disconnection is completed,
NO CONNECTION is displayed.
#
If this unit fails to find any available cellular
phones, NOT FOUND is displayed.
You can display the BD address by touching
#
BD ADDR. To return to the device name, touch
PHONE NAME.
3
Touch the device name you want to
connect.
While connecting, CONNECTING flashes. To
complete the connection, check the device
60
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
3
Touch the device name you want to
Registering a connected
cellular phone
connect.
While connecting, CONNECTING is flashing.
If the connection is established, CONNECTED
is displayed.
1
Touch PHONE REGISTER on the function
menu.
Registration assignments for user phone 1, 2
and 3 appear on the display.
Connecting to a registered phone
automatically
2
Touch and hold one of the registration
assignments to register the currenctly con-
nected phone.
1
Touch NEXT on the function menu.
If the registration is succeeded, the device
name of the connected phone is displayed in
the selected assignment.
2
Touch AUTO CONNECT to turn the
Automatic Connection function on.
If your cellular phone is ready for Bluetooth
wireless connection, connection to this unit is
automatically established.
#
If the assignment is empty, the device name is
not displayed. If the assignment is already taken,
the device name appears. To replace an assign-
ment with a new phone, first delete the current
assignment. For more detailed instructions, see
#
To turn automatic connection off, touch
AUTO CONNECT again.
Using the phone book
#
If the registration failed, device name of the
connected phone is not displayed in the selected
assignment. In this case, return to step 1 and try
again.
Transferring entries to the phone book
The Phone Book can hold a total of 500 en-
tries. 300 from User 1, 150 from User 2, and 50
from User 3.
Deleting a registered phone
1
Touch PHONE BOOK TRANSFER on the
function menu.
1
Touch PHONE REGISTER on the function
menu.
2
Touch START to turn the Phone Book
Transfer function on.
2
Touch DELETE next to the device name
The Phone Book Transfer is now on standby.
you want to delete.
A confirmation display appears. Touch OK to
delete the phone.
3
Use the cellular phone to perform
phone book transfer.
#
To cancel deleting a registered phone, touch
Perform phone book transfer using the cellu-
lar phone. For detailed instructions, refer to
the instruction manual that came with your
cellular phone.
CANCEL.
Connecting to a registered
cellular phone
#
The display indicates how many entries have
been transferred and the total number to be
transferred.
#
Connecting to a registered phone
manually
To cancel the transferring process, touch
STOP.
1
Touch PHONE CONNECT on the function
menu.
4
When you are done transferring Phone
Book entries, touch ESC.
2
Touch DIRECT CONNECT.
61
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
5
Touch phone number of the Phone
Note
Book entry you want to call.
When the phone book transfer is complete, the
connection to your cellular phone is off. To use
the Phone Book, connect to your cellular phone
once again, referring to Connecting to a registered
If several phone numbers are entered to an
entry, touch one you want to call.
The display returns to the normal display and
the Phone Book entry you selected is dis-
played on the information bar.
6
#
Touch to make a call.
For an international call, touch add “+” to add
Changing the phone book display order
%
Touch PHONE BOOK NAME VIEW on
the function menu to change the name
view order.
+ to the phone number.
7
To end the call, touch
.
INVERTED is displayed and the name view
order is changed.
Editing phone numbers
#
To change to the original order (ORIGINAL),
Important
touch PHONE BOOK NAME VIEW again.
Be sure to park your vehicle and apply the park-
ing brake when performing this operation.
Calling a number in the phone book
Important
You can edit the numbers of Phone Book en-
tries. Each phone number can be up to 24 di-
gits long.
Be sure to park your vehicle and apply the park-
ing brake when performing this operation.
1
Touch PHONE BOOK to display the
1
Touch PHONE BOOK to display the
Phone Book.
Phone Book.
2
edit.
Select a Phone Book entry you want to
2
Touch a or b to select the first letter of
the name you are looking for.
Touching a or b changes alphabetical letters.
See step two to four on Calling a number in the
3
Touch ENTER to show entries starting
3
Touch EDIT next to the phone number
with the letter you chose.
you want to edit.
The display is changed to the Phone Book dial
edit display.
The display shows the first six Phone Book en-
tries starting with that letter (e.g. “Ben”,
“Brian” and “Burt” when “B” is selected).
#
tries.
#
Touch or to display other phone book en-
4
#
Touch 0 to 9 to input numbers.
For an international call, touch add “+” to add
To refine the search with a different letter,
+ to the phone number.
Touch CLEAR to delete the number. Touch and
hold CLEAR to delete all the input numbers.
touch CLEAR.
#
4
Touch a Phone Book entry you want to
call.
5
Touch OK to store the new number.
The display is switched to the Phone Book de-
tail display.
62
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
2
Touch a phone number or name (if en-
Clearing a phone book entry
tered) you want to call.
Important
The display returns to the normal display and
the phone number you selected is displayed
on the information bar.
Be sure to park your vehicle and apply the park-
ing brake when performing this operation.
3
Touch to make a call.
1
Touch PHONE BOOK to display the
#
For an international call, touch add “+” to add
Phone Book.
+ to the phone number.
2
Select a Phone Book entry you want to
4
To end the call, touch
.
delete.
See step two to four on Calling a number in the
this.
Using preset numbers
Important
3
Touch DELETE to delete the Phone Book
Be sure to park your vehicle and apply the park-
ing brake when performing this operation.
entry.
A confirmation display appears. Touch YES to
delete the entry.
#
If you do not want to clear a Phone Book entry
Assigning preset numbers
Numbers that you dial frequently can be as-
signed to presets for quick recall.
that you have selected, touch NO.
You can assign up to 6 frequently called phone
numbers to number presets.
Using the call history
Important
1
Select a desired phone number from
Be sure to park your vehicle and apply the park-
ing brake when performing this operation.
the phone book or the call history. Or di-
rectly enter a desired phone number.
To select a desired phone number from the
Phone Book or the Call History, see the in-
structions explained in previous pages. To di-
rectly enter a desired phone number, see
The 6 most recent calls made (dialled), re-
ceived and missed, are stored in the Call His-
tory. You can browse the Call History and call
numbers from it.
1
Touch LOG to display the Call History.
Touching LOG repeatedly switches between
the following call histories:
MISSED CALL LIST (missed call)—
DIALED CALL LIST (dialled call)—
RECEIVED CALL LIST (received call)
The display should now be the normal display
and the selected phone number is displayed
on the information bar.
2
Touch LIST to display preset assign-
ments.
#
You can switch between phone number and
name (if entered) by touching ABC/123.
If no phone numbers have been stored in the
selected list, nothing is displayed.
Preset assignments appear in the display (if
not displayed yet).
#
3
Keep touching one of preset assign-
ments to store the phone number.
The phone number you selected is stored in
presets.
63
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
#
No Data is displayed for empty assignment.
Clearing memory
Even if the assignment is taken, you can replace
it to the new one by keeping touching the assign-
ment.
1
Touch CLEAR MEMORY on the function
menu.
2
Touch CLEAR next to the item you want
Recalling preset numbers
to delete from the memory.
Select from the following:
1
Touch LIST to display preset assign-
!
!
!
!
!
PHONE BOOK (phone book)
ments.
DIALED CALLS (dialled call history)
RECEIVED CALLS (received call history)
MISSED CALLS (missed call history)
DIAL PRESET (preset phone numbers)
Preset assignments appear in the display (if
not displayed yet).
2
Touch one of preset assignments.
After selecting a desired item, a confirmation
display appears. Touch OK to delete the mem-
ory.
The selected phone number should now be
displayed on the information bar.
3
4
Touch to make a call.
To end the call, touch
#
If you do not want to clear memory that you
have selected, touch CANCEL.
If you want to clear all the Phone Book,
.
#
dialled/received/missed call history list and pre-
set phone number, touch CLEAR ALL.
Making a call by entering
phone number
Setting automatic answering
Important
%
Touch AUTO ANSWER on the function
menu to turn the automatic answer on.
To turn the automatic answer off, touch
Be sure to park your vehicle and apply the park-
ing brake when performing this operation.
#
AUTO ANSWER again.
1
Touch DIRECT to display the direct dial
display.
Setting automatic rejecting
2
#
Touch 0 to 9 to input numbers.
For an international call, touch add “+” to add
1
Touch NEXT on the function menu.
+ to the phone number.
Touch CLEAR to delete the number. Touch and
hold CLEAR to delete all the input numbers.
#
2
Touch REFUSE ALL CALLS to turn the
automatic call rejection on.
To turn the automatic call rejection off, touch
#
#
Up to 24 digits can be entered.
If you want to store the entered phone number
#
REFUSE ALL CALLS again.
to preset assignment, touch SET here. The display
returns to the normal display and the phone num-
ber you entered is selected.
Switching the ring tone
1
Touch NEXT on the function menu.
3
When you completed entering the
number, touch to make a call.
2
Touch RING TONE to turn the ring tone
on.
#
4
To end the call, touch
.
To turn the ring tone off, touch RING TONE
again.
64
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
Echo canceling and noise reduction
Multi-CD Player
Basic Operations
1
Touch NEXT on the function menu.
You can use this unit to control a multi-CD
player, which is sold separately.
2
Touch ECHO CANCEL to turn Echo Can-
cel function on.
To turn echo canceling off, touch
!
!
!
This unit does not have ITS playlist, disc title
and track title list functions.
Only functions described in this manual are
supported by 50-disc multi-CD players.
This unit is not designed to operate disc title
list functions with a 50-disc multi-CD player.
#
ECHO CANCEL again.
Displaying BD (Bluetooth
Device) address
Displaying BD address of this system
1
2
3 4
5
1
Touch NEXT on the function menu.
2
Touch DEVICE INFO to display the BD
address.
Various information regarding the Bluetooth
wireless technology are displayed.
!
DEVICE NAME (device name of this sys-
tem)
1 Source icon
2 Disc number indicator
3 Disc title indicator
!
!
BD ADDRESS (address of Bluetooth device)
SYSTEM VERSION (version of this unit’s
microprocessor)
Shows the title of the currently playing disc
only when playing CD TEXT discs.
4 Track number indicator
!
BT MODULE VERSION (version of Blue-
tooth module)
5 Play time indicator
Displaying BD address of your
cellular phone
1
Touch the source icon and then touch
MCD to select the multi-CD player.
1
Touch PHONE CONNECT on the function
menu.
2
3
Touch a or b to select a disc.
2
Touch BD ADDRESS to display the BD
To skip back or forward to another
address.
track, briefly touch o or p.
12-digit hexadecimal string is displayed.
#
To return to the device name, touch
4
To perform fast forward or reverse,
PHONE NAME.
keep touching o or p.
Notes
!
!
When multi-CD player completes preparatory
operations, READY is displayed.
If an error message such as ERROR-02-XX is
displayed, refer to the multi-CD player owner’s
manual.
!
If there are no discs in the multi-CD player ma-
gazine, NO DISC is displayed.
65
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
Selecting a disc
Function name Operation
1
Touch LIST.
However, the repeat play ranges
you can select are different from
that of the built-in DVD player. The
repeat play ranges of the multi-CD
player are:
2
Touch your favorite disc.
Selectable discs are highlighted.
REPEAT
3
play.
Touch ESC to return to the ordinary dis-
!
!
!
MULTI-CD – Repeat all discs in
the multi-CD player
TRACK – Repeat just the cur-
rent track
Pausing CD playback
DISC – Repeat the current disc
%
#
Touch de during playback.
To resume playback at the same point that you
Refer to Playing tracks in random
RANDOM
SCAN
turned pause on, touch de again.
Refer to Scanning tracks or folders
Multi-CD player has COMP (com-
pression) and DBE (dynamic bass
Introduction of advanced
operations
You can only use these functions with a multi-
CD player that supports them.
COMPRESSION emphasis) functions.
The settings can be switched as
below:
1
Touch AV MENU and then touch
OFF—COMP1—COMP2—OFF—
DBE 1—DBE 2
FUNCTION MENU to display the function
names.
The function names are displayed and oper-
able ones are highlighted.
Notes
!
!
If you select other discs during repeat play,
the repeat play range changes to MULTI-CD.
If you perform track search or fast forward/re-
verse during TRACK, the repeat play range
changes to DISC.
2
play.
#
Touch ESC to return to the playback dis-
To return to the previous display, touch BACK.
Function and operation
REPEAT, RANDOM, SCAN and
COMPRESSION operations are basically the
same as that of the built-in DVD player.
!
!
After track or disc scanning is finished, nor-
mal playback of the tracks begins again.
If the multi-CD player does not support
COMP/DBE, you cannot operate this function.
Using CD TEXT functions
You can use these functions only with a CD
TEXT compatible multi-CD player.
The operation is the same as that of the built-
in DVD player.
66
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
3
To skip back or forward to another
DVD Player
Basic Operations
chapter/track, briefly touch o or p.
4
To perform fast forward or reverse,
You can use this unit to control a DVD player or
multi-DVD player, which is sold separately.
For details concerning operation, refer to the
DVD player’s or multi-DVD player’s operation
manual. This section provides information on
DVD operations with this unit which differs
from that described in the DVD player’s or
multi-DVD player’s operation manual.
keep touching o or p.
Note
If you do not use the touch panel keys within 30
seconds, they will be hidden automatically when
playing DVD video or Video CD.
!
This unit does not have ITS playlist and disc
title functions.
Selecting a disc
!
You can operate this function only when a
multi-DVD player is connected to this unit.
1 2 3 4
5
6
1
2
Touch LIST.
Touch your favorite disc.
Selectable discs are highlighted.
3
Touch ESC to return to the ordinary dis-
play.
7
Note
1 Source icon
2 Media indicator
3 Disc number indicator
You can also select a disc by keeping touching a
or b.
Shows the number of the disc currently play-
ing when using a multi-DVD player.
4 Title/Folder number indicator
5 Chapter/track number indicator
6 Play time indicator
Selecting a folder
!
You can operate this function only when a
DVD player compatible with compressed
audio playback is connected to this unit.
7 Variable message area
%
Touch a or b to select a folder.
Shows the text information of disc currently
playing when playing a compressed audio
disc.
Pausing disc playback
!
This unit cannot display the text infor-
mation recorded on a CD TEXT disc
playing on the optional DVD player.
%
#
Touch de during playback.
To resume playback at the same point that you
turned pause on, touch de again.
1
Touch the source icon and then touch
S-DVD to select the DVD player.
When the source icon is not displayed, you
can display it by touching the screen.
#
2
Touch the screen to display the touch
panel keys.
67
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
ing TRACK, the repeat play range changes to
DISC.
Introduction of advanced
operations
!
!
When playing back compressed audio, if you
select another folder during repeat play, the
repeat play range changes to DISC.
When playing back compressed audio, if you
perform track search or fast forward/reverse
during TRACK, the repeat play range changes
to FOLDER.
1
Touch AV MENU and then touch
FUNCTION MENU to display the function
names.
The function names are displayed and oper-
able ones are highlighted.
2
Touch ESC to return to the playback dis-
play.
Displaying text information of an
audio file
#
To return to the previous display, touch BACK.
The operation is the same as that of the built-
in DVD player.
Function and operation
REPEAT, RANDOM and SCAN operations are
basically the same as that of the built-in DVD
player.
!
If the characters recorded on the audio file
are not compatible with this unit, those
characters will not be displayed.
Function name Operation
But the repeat play range that you
can select is vary depending on
the type of disc or system. The re-
peat play ranges of the DVD
player/multi-DVD player are as
below:
Selecting files from the file name list
!
You can operate this function only when a
DVD player compatible with compressed
audio playback is connected to this unit.
During PBC playback of Video
CDs, this function cannot be oper-
ated.
1
2
Touch LIST to display the disc list.
Touch LIST repeatedly to switch the
REPEAT
!
!
DISC – Repeat the current disc
FOLDER – Repeat the current
folder
lists.
DISC LIST (disc list)—FOLDER&FILE LIST
(folder and file list)
!
!
!
TITLE – Repeat just the current
title
CHAPTER – Repeat just the
current chapter
TRACK – Repeat the current
track
3
Select the desired file name (or folder
name).
The operation is the same as that of the built-
in DVD player.
Refer to Playing tracks in random
RANDOM
SCAN
Refer to Scanning tracks or folders
Notes
!
!
If you select other discs during repeat play,
the repeat play range changes to DISC.
When playing back Video CD or CD, if you per-
form track search or fast forward/reverse dur-
68
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
#
If you keep touching c or d you can skip
TV tuner
broadcasting channels. Seek tuning starts as
Basic Operations
soon as you release the keys.
You can use this unit to control a TV tuner (e.g.
GEX-P5700TV), which is sold separately.
For details concerning operation, refer to the
TV tuner’s operation manual. This section pro-
vides information on TV operations with this
unit, which differs from that described in the
TV tuner’s operation manual.
Note
If you do not use the touch panel keys within 30
seconds, they will be hidden automatically.
Storing and recalling broadcast
stations
If you touch any of the preset tuning keys P01
to P12 you can easily store up to 12 broadcast
stations for later recall with the touch of a key.
1 2
3
4
!
Up to 24 stations, 12 for each of two TV
bands, can be stored in memory.
1
Touch LIST to display the preset list.
#
When the touch panel keys are not displayed,
you can display them by touching the screen.
1 Source icon
2 Band indicator
3 Preset number indicator
4 Channel indicator
2
When you find a station that you want
to store in memory, keep touching one of
preset tuning keys P01 to P12 until the
beep sounds.
The next time you touch the same preset tun-
ing key the station is recalled from memory.
1
Touch the source icon and then touch
TV to select the TV.
When the source icon is not displayed, you
can display it by touching the screen.
#
#
To switch between P01 to P06 and P07 to P12,
touch PREV or NEXT.
2
Touch the screen to display the touch
3
play.
Touch ESC to return to the ordinary dis-
panel keys.
3
Touch BAND to select a band.
Touch BAND repeatedly until the desired band
Note
is displayed, TV1 or TV2.
You can also use a and b to recall stations as-
signed to preset tuning keys P01 to P12.
4
To perform manual tuning, briefly
touch c or d.
Storing the strongest broadcast
stations sequentially
5
To perform seek tuning, keep touching
c or d for about one second and release.
The tuner will scan the channels until a broad-
cast strong enough for good reception is
found.
1
Touch AV MENU and then touch
FUNCTION MENU to display the function
names.
#
You can cancel seek tuning by briefly touching
either c or d.
69
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
2
Touch BSSM on the function menu to
Digital Signal Processor
Introduction of DSP adjustments
You can use this unit to control multi-channel
processor (e.g. DEQ-P8000), which is sold sepa-
rately.
turn BSSM on.
BSSM begins to flash. While BSSM is flashing
the 12 strongest broadcast stations will be
stored in order from the lowest channel up.
When finished, BSSM stops flashing.
#
To cancel the storage process, touch BSSM
!
Some functions may differ depending on the
multi-channel processor connected to this
unit.
again.
3
Touch ESC to return to the TV picture.
#
To return to the previous display, touch BACK.
Important
When a multi-channel processor and an optional
DVD player are connected to this unit, be sure to
use an optical cable (e.g., CD-AD600).
Note
Storing broadcast stations with BSSM may re-
place broadcast stations you have saved using
P01 to P12.
1
1 DSP display
Shows the DSP function names.
By carrying out the following settings/adjust-
ments in the order shown, you can create a fi-
nely-tuned sound field effortlessly.
1
2
3
4
5
6
7
8
1
Touch AV MENU and then touch
DSP MENU to display the DSP function
names.
The DSP function names are displayed and
operable ones are highlighted.
70
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
#
To go to the next group of function names,
2
Press EQ to select the desired SFC
touch NEXT.
mode.
#
To return to the previous group of function
MUSICAL (musical)—DRAMA (drama)—
ACTION (action)—JAZZ (jazz)—HALL (hall)—
CLUB (club)—OFF (off)
names, touch PREV.
#
When playing discs recorded with more than
96 kHz sampling frequency, you cannot use audio
functions. Also, equalizer curve setting,
POSITION, AUTO EQ and AUTO TA will be can-
celled.
Note
If the source is a 2-channel LPCM audio or a 2-
channel Dolby Digital audio and you select SFC
effects that are most applicable for 5.1-channel
audio (i.e., MUSICAL, DRAMA or ACTION), we
recommend turning Dolby Pro Logic II on. On the
other hand, when selecting SFC effects that are
intended for use with 2-channel audio (i.e., JAZZ,
HALL or CLUB), we recommend turning Dolby
Pro Logic II off.
#
When playing discs recorded with more than
96 kHz sampling frequency, audio is outputted
from front speakers only.
#
When selecting FM as the source, you cannot
switch to SLA.
When playing other than the DVD disc, you
cannot switch to DYNAMIC RANGE CONTROL.
When neither FRONT-L nor FRONT-R is se-
#
#
lected in POSITION, you cannot switch to
TIME ALIGNMENT.
Using the position selector
#
When both the center speaker and the rear
One way to assure a more natural sound is to
accurately position the stereo image, putting
you right in the center of the sound field. The
position selector function lets you automati-
cally adjust the speaker output levels and in-
serts a delay time to match the number and
position of occupied seats. When used in con-
junction with the SFC, the feature will make
the sound image more natural and offer a pa-
noramic sound that envelops you.
speaker are set to OFF in the speaker setting, you
cannot switch to DOLBY PRO LOGIC II.
2
Touch ESC to return to the ordinary dis-
play.
#
To return to the previous display, touch BACK.
Using the sound field control
The SFC function creates the sensation of a
live performance.
1
Touch POSITION on the DSP function
!
The acoustics of different performance en-
vironments are not the same and depend
on the extent and contour of space through
which sound waves move and on how
sounds bounce off the stage, walls, floors
and ceilings. At a live performance you
hear music in three stages: direct sound,
early reflections, and late reflections, or re-
verberations. Those factors are programed
into the SFC circuitry to recreate the acous-
tics of various performance settings.
menu.
2
Touch c/d/a/b to select a listening po-
sition.
Touch one of these, c/d/a/b, to select a lis-
tening position as listed in the table.
Key
c
Display
FRONT-L
FRONT-R
FRONT
ALL
Position
Front seat left
Front seat right
Front seats
All seats
d
a
1
Press EQ and hold to switch to SFC
b
function.
#
To switch to equalizer function, press EQ and
#
To cancel the selected listening position,
hold again.
touch the same key again.
71
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
2
3
Touch SLA on the DSP function menu.
Note
When you make adjustments to the listening po-
sition, the speaker outputs are automatically set
for appropriate levels. You can tailor the levels
more precisely referring to Adjusting the speaker
Touch c or d to adjust the source vo-
lume.
Each time you touch c or d it increases or de-
creases the source volume.
+4 to –4 is displayed as the source volume is
increased or decreased.
Notes
Using balance adjustment
You can change the fader/balance setting so
that it can provide the ideal listening environ-
ment in all occupied seats.
!
!
The AM volume level can also be adjusted
with source level adjustments.
Video CD, CD, compressed audio and DivX
are set to the same source level adjustment
volume automatically.
1
Touch FADER/BALANCE on the DSP
!
!
!
DVD and the optional DVD player are set to
the same source level adjustment volume
automatically.
External unit 1 and external unit 2 are set to
the same source level adjustment volume
automatically.
AUX (auxiliary input) and AV (AV input) are set
to the same source level adjustment volume
automatically.
function menu.
2
Touch a or b to adjust front/rear
speaker balance.
Each time you touch a or b it moves the
front/rear speaker balance towards the front or
the rear.
FRONT:25 to REAR:25 is displayed as the
front/rear speaker balance moves from front to
rear.
#
FR: 0 is the proper setting when only two
Using the dynamic range control
speakers are used.
The dynamic range refers to the difference be-
tween the largest and softest sounds. The dy-
namic range control compresses this
difference so that you can clearly hear sounds
even at low volume levels.
3
Touch c or d to adjust left/right speak-
er balance.
Each time you touch c or d it moves the left/
right speaker balance towards the left or the
right.
LEFT:25 to RIGHT:25 is displayed as the left/
right speaker balance moves from left to right.
!
The dynamic range control is effective only
on Dolby Digital sounds.
!
When playing other than the DVD disc, you
cannot switch to
DYNAMIC RANGE CONTROL.
Adjusting source levels
SLA (source level adjustment) lets you adjust
the volume level of each source to prevent ra-
dical changes in volume when switching be-
tween sources.
1
Touch DYNAMIC RANGE CONTROL on
the DSP function menu.
2
Touch d to turn the dynamic range con-
trol on.
To turn dynamic range control off, touch c.
!
Settings are based on the FM volume level,
which remains unchanged.
#
1
Compare the FM volume level with the
level of the source you wish to adjust.
72
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
!
!
MUSIC – The Music mode suitable for
music playback
MATRIX – The Matrix mode for when FM
radio reception is weak
Using the down-mix function
The down-mix function allows you to play back
multi-channel audio in 2 channels.
!
!
OFF – Turn Dolby Pro Logic II off
MUSIC ADJUST – Adjust the Music mode
1
Touch DOWN MIX on the DSP function
menu.
#
You can operate MUSIC ADJUST only when
2
Touch c or d to select the desired level.
MUSIC has been selected.
!
!
Lo/Ro – Stereo mix the original audio that
do not contain channel modes such as sur-
round components.
Lt/Rt – Down mix so that the surround
components can be restored (decoded).
Adjusting the Music mode
You can adjust the Music mode with the fol-
lowing three controls.
!
Panorama (PANORAMA) extends the front
stereo image to include the surround
speakers for an exciting “wraparound” ef-
fect.
Using the direct control
You can override audio settings to check for ef-
fectiveness of your audio settings.
!
!
Dimension (DIMENSION) allows you to
gradually adjust the sound field either to-
wards the front or the rear.
Center Width Control (CENTER WIDTH) al-
lows center-channel sounds to be posi-
tioned between the center speaker and the
left/right speakers. It improves the left-cen-
ter-right stage presentation for both the dri-
ver and the front passenger.
!
All audio functions are locked out when the
direct control is on except VOLUME/MUTE
and DOLBY PRO LOGIC II.
1
Touch DIGITAL DIRECT on the DSP func-
tion menu.
2
#
Touch d to turn the direct control on.
To turn direct control off, touch c.
1
2
3
Touch NEXT on the DSP function menu.
Touch DOLBY PRO LOGIC II.
Using the Dolby Pro Logic II
Dolby Pro Logic II creates five full-bandwidth
output channels from two-channel sources to
achieve high-purity matrix surround.
Touch MUSIC and then touch
MUSIC ADJUST.
You can operate MUSIC ADJUST only when
MUSIC has been selected.
#
!
Dolby Pro Logic II supports up to 48kHz
sampling rate stereo source and has no ef-
fect on other types of source.
4
Touch a or b to select PANORAMA (pa-
!
When both the center speaker and the rear
speaker are set to OFF in the speaker set-
ting, you cannot switch to
norama).
Each time you touch a or b selects the item
in the following order:
PANORAMA (panorama)—DIMENSION (di-
mension)—CENTER WIDTH (center width)
DOLBY PRO LOGIC II.
1
2
3
Touch NEXT on the DSP function menu.
Touch DOLBY PRO LOGIC II.
5
on.
#
Touch d to turn the panorama control
To turn the panorama control off, touch c.
Touch any of the following touch panel
keys to select the desired mode.
!
MOVIE – The Movie mode suitable for
movie playback
73
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
6
Touch b to select DIMENSION and then
SUB WOOFER (subwoofer)—PHASE (subwoo-
touch c or d to adjust front/surround
speaker balance.
fer setting)
#
You can switch to PHASE only when the sub-
Each time you touch c or d it moves the
sound towards the front or the surrounds.
+3 to –3 is displayed as the front/surround
speaker balance moves from front to sur-
rounds.
woofer has been set to ON.
4
Touch c or d to select the correct size
for the selected speaker.
Each time you touch c or d selects the size in
the following order:
7
Touch b to select CENTER WIDTH and
OFF (off)—SMALL (small)—LARGE (large)
then touch c or d to adjust the center
image.
Each time you touch c or d it gradually
spreads the center channel sound into the
front left and right speakers over a range 0 to
7.
#
You cannot select OFF, when FRONT (front
speakers) have been selected.
You can select ON or OFF, when
SUB WOOFER (subwoofer) has been selected.
You can switch REVERSE (reverse phase) or
#
#
NORMAL (normal phase), when PHASE (subwoo-
3 is the default and it’s recommended for
most recordings. 0 places all center sound in
the center speaker. 7 places all center sound
equally in the left/right speakers.
fer setting) has been selected.
Correcting the subwoofer’s phase
If trying to boost the bass output of the sub-
woofer doesn’t do much or rather makes you
feel that the bass gets more murky, this may
indicate that the subwoofer’s output and bass
content you hear over other speakers cancel
each other out. To remove this problem, try
changing the phase setting for the subwoofer.
Setting the speaker setting
You need to make with/without (or yes/no) and
size (bass reproducing capacity) selection/ad-
justments depending on the installed speak-
ers. The size needs to be set to LARGE (large)
if the speaker is capable of reproducing
sounds of about 100 Hz or below. Otherwise
select SMALL (small).
1
2
3
Touch NEXT on the DSP function menu.
Touch SPEAKER SETTING.
!
Low frequency range is not output if the
subwoofer is set to OFF and the front and
rear speakers set to SMALL or OFF.
It is imperative that non-installed speakers
be set to OFF.
Set the front or rear speaker to LARGE if
the speaker is capable of reproducing bass
content, or if no subwoofer is installed.
Touch a or b to select SUB WOOFER
(subwoofer).
Each time you touch a or b selects the speak-
er in the following order:
FRONT (front speakers)—CENTER (center
speaker)—REAR (rear speakers)—
SUB WOOFER (subwoofer)—PHASE (subwoo-
fer setting)
!
!
1
2
3
Touch NEXT on the DSP function menu.
Touch SPEAKER SETTING.
4
#
Touch d to turn subwoofer output on.
To turn subwoofer output off, touch c.
5
Touch b and then touch c or d to se-
Touch a or b to select the speaker to
lect the phase of subwoofer output.
Touch d to select normal phase and
NORMAL appears in the display. Touch c to
select reverse phase and REVERSE appears in
the display.
be adjusted.
Each time you touch a or b selects the speak-
er in the following order:
FRONT (front speakers)—CENTER (center
speaker)—REAR (rear speakers)—
74
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
Selecting a cross-over frequency
Note
You can select a frequency, under which
sounds are reproduced through the subwoo-
fer. If the installed speakers include one whose
size has been set to SMALL, you can select a
frequency, under which sounds are repro-
duced through a LARGE speaker or subwoo-
fer.
When playing a 2-channel mono source with Pro
Logic turned on, there may be occasions when
the following will occur:
!
No audio is outputted if the center speaker
setting is SMALL or LARGE and no center
speaker is installed.
!
Audio is heard only over the center speaker if
installed and the center speaker setting is
SMALL or LARGE.
1
2
3
Touch NEXT on the DSP function menu.
Touch CROSS OVER.
Touch a or b to select the speaker to
Adjusting the speaker output
levels
Speaker level can be adjusted finely by listen-
ing to an audio output. First, use test tone to
adjust the approximate speaker level, and then
use this function to adjust finely.
be adjusted.
Each time you touch a or b selects the speak-
er in the following order:
FRONT (front speakers)—CENTER (center
speaker)—REAR (rear speakers)—
SUB WOOFER (subwoofer)
1
2
3
Touch NEXT on the DSP function menu.
Touch SPEAKER LEVEL.
4
Touch c or d to select cross-over fre-
quency.
Each time you touch c or d selects cross-over
frequencies in the following order:
63Hz—80Hz—100Hz—125Hz—160Hz—
200Hz
Touch a or b to select the speaker to
be adjusted.
Each time you touch a or b selects the speak-
er in the following order:
FRONT L (front speaker left)—CENTER (center
speaker)—FRONT R (front speaker right)—
REAR R (rear speaker right)—REAR L (rear
speaker left)—SUB WOOFER (subwoofer)
Note
Selecting a cross-over frequency is to set a cross-
over frequency of the subwoofer’s L.P.F. (low-pass
filter) and that of the SMALL speaker H.P.F. (high-
pass filter). The cross-over frequency setting has
no effect if the subwoofer is set to OFF and other
speakers are set to LARGE or OFF.
#
You cannot select speakers whose size is set
4
Touch c or d to adjust the speaker out-
put level.
Adjusting the speaker output
levels using a test tone
This function allows you to easily get the over-
all balance right among the speakers.
Each time you touch c or d increases or de-
creases the speaker output level. +10 to –10 is
displayed as the level is increased or de-
creased.
1
2
Touch NEXT on the DSP function menu.
Touch TEST TONE.
Note
To adjust the speaker output levels in this mode is
the same as making the speaker output levels at
TEST TONE. Both provide the same results.
75
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
3
Touch START to start the test tone out-
3
Touch any of the following touch panel
put.
keys to select the time alignment.
The test tone is outputted. It rotates from
speaker to speaker in the following sequence
at intervals of about two seconds. The current
settings for the speaker over which you hear
the test tone are shown in the display.
FRONT L (front speaker left)—CENTER (center
speaker)—FRONT R (front speaker right)—
REAR R (rear speaker right)—REAR L (rear
speaker left)—SUB WOOFER (subwoofer)
Check each speaker output level. If no adjust-
ments are needed, perform step 5 to stop the
test tone.
!
!
INITIAL – Initial time alignment (factory set-
ting)
AUTO TA – Time alignment created by auto
TA and EQ. (Refer to Auto TA and EQ (auto-
CUSTOM – Adjusted time alignment that
you can create for yourself
OFF – Turn the time alignment off
ADJUSTMENT – Adjust the time alignment
as desired
!
!
!
#
You cannot select AUTO TA if auto TA and EQ
has not been carried out.
# You cannot select ADJUSTMENT when
#
The settings do not appear for speakers
neither FRONT-L nor FRONT-R is selected in
POSITION.
4
Touch c or d to adjust the speaker out-
put level.
Adjusting the time alignment
You can adjust the distance between each
speaker and the selected position.
Each time you touch c or d increases or de-
creases the speaker output level. +10 to –10 is
displayed as the level is increased or de-
creased.
!
An adjusted time alignment is memorized
in CUSTOM.
#
The test tone rotates to the next speaker after
about two seconds from the last operation.
1
2
Touch NEXT on the DSP function menu.
5
Touch STOP to stop the test tone out-
Touch TIME ALIGNMENT and then
put.
touch ADJUSTMENT.
You cannot select ADJUSTMENT when
#
Notes
neither FRONT-L nor FRONT-R is selected in
!
!
If needed, select speakers and adjust their ‘ab-
To adjust the speaker output levels in this
mode is the same as making the speaker out-
put levels at SPEAKER LEVEL. Both provide
the same results.
POSITION.
3
Touch a or b to select the speaker to
be adjusted.
Each time you touch a or b selects the speak-
er in the following order:
FRONT L (front speaker left)—CENTER (center
speaker)—FRONT R (front speaker right)—
REAR R (rear speaker right)—REAR L (rear
speaker left)—SUB WOOFER (subwoofer)
Using the time alignment
The time alignment lets you adjust the dis-
tance between each speaker and the listening
position.
#
You cannot select speakers whose size is set
1
2
Touch NEXT on the DSP function menu.
Touch TIME ALIGNMENT.
76
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
4
Touch c or d to adjust the distance be-
center frequency, an equalizer level and a Q
factor for each band.
tween the selected speaker and the listen-
ing position.
Each time you touch c or d increases or de-
creases the distance. 0.0inch to 200.0inch is
displayed as the distance is increased or de-
creased.
!
!
!
A separate CUSTOM1 curve can be cre-
ated for each source.
A CUSTOM2 curve can be created com-
mon to all sources.
The center speaker largely determines the
sound image and getting the balance right
isn’t easy. We recommend reproducing a 2-
ch. audio (a CD for example) and getting
the balance right among the speakers ex-
cept for the center, and then reproducing a
5.1-ch. audio (Dolby Digital or DTS) and ad-
justing the center speaker output to the
balance you have already got among the
other speakers.
Using the equalizer
The equalizer lets you adjust the equalization
to match the car’s interior acoustic character-
istics as desired.
Recalling equalizer curves
There are seven stored equalizer curves which
you can easily recall at any time. Here is a list
of the equalizer curves.
1
Touch NEXT twice on the DSP function
menu.
2
Touch PARAMETRIC EQ.
Display
Equalizer curve
Powerful
Natural
POWERFUL
NATURAL
VOCAL
3
Touch a or b to select the desired item.
Each time you touch a or b selects the item
in the following order:
EQ (equalizer)—SP-SELECT (speakers)—
BAND (bands)—FREQUENCY (center fre-
quency)—LEVEL (equalizer level)—
Q. FACTOR (Q factor)
Vocal
FLAT
Flat
CUSTOM1
CUSTOM2
SUPER BASS
Custom 1
Custom 2
Super bass
4
Touch d to select the equalizer.
Touch d repeatedly to switch between the fol-
lowing equalizers:
POWERFUL—NATURAL—VOCAL—FLAT—
CUSTOM1—CUSTOM2—SUPER BASS
!
!
CUSTOM1 and CUSTOM2 are adjusted
equalizer curves.
When FLAT is selected, no supplement or
correction is made to the sound. This is
useful to check the effect of the equalizer
curves by switching alternatively between
FLAT and a set equalizer curve.
5
Touch b and then touch c or d to se-
lect the speaker to be adjusted.
Touch c or d until the desired speaker ap-
pears in the display.
REAR (rear speakers)—CENTER (center speak-
er)—FRONT (front speakers)
%
Press EQ repeatedly to switch between
the following equalizers:
POWERFUL—NATURAL—VOCAL—FLAT—
CUSTOM1—CUSTOM2—SUPER BASS
#
You cannot select speakers whose size is set
Adjusting 3-band parametric equalizer
6
Touch b and then touch c or d to se-
lect the equalizer band to be adjusted.
Each time you touch c or d selects equalizer
bands in the following order:
For CUSTOM1 and CUSTOM2 equalizer
curves, you can adjust the front, rear and cen-
ter equalizer curves separately by selecting a
77
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
LOW (low)—MID (mid)—HIGH (high)
3
Touch d to turn the auto-equalizer on.
#
To turn auto-equalizer off, touch c.
7
Touch b and then touch c or d to se-
lect the center frequency of selected band.
Touch c or d until the desired frequency ap-
pears in the display.
40Hz—50Hz—63Hz—80Hz—100Hz—125Hz
—160Hz—200Hz—250Hz—315Hz—400Hz—
500Hz—630Hz—800Hz—1kHz—1.25kHz—
1.6kHz—2kHz—2.5kHz—3.15kHz—4kHz—
5kHz—6.3kHz—8kHz—10kHz—12.5kHz
Auto TA and EQ (auto-time
alignment and auto-equalizing)
The auto-time alignment is automatically ad-
justed for the distance between each speaker
and the listening position.
The auto-equalizer automatically measures
the car interior acoustic characteristics, and
then creates the auto-equalizer curve based
on that information.
8
Touch b and then touch c or d to ad-
just the equalizer level.
Each time you touch c or d it increases or de-
creases the equalizer level. +12 to –12 is dis-
played as the level is increased or decreased.
WARNING
To prevent accidents, never carry out auto TA and
EQ while driving. When this function measures
the car interior acoustic characteristics to create
an auto-equalizer curve, a loud measurement
tone (noise) may be outputted from the speakers.
9
Touch b and then touch c or d to se-
lect the desired Q factor.
Each time you touch c or d switches between
the following Q factor:
NARROW (narrow)—WIDE (wide)
#
You can adjust parameters for each band of
CAUTION
the other speakers in the same way.
!
Carrying out auto TA and EQ under the follow-
ing conditions may damage the speakers. Be
sure to check the conditions thoroughly be-
fore carrying out auto TA and EQ.
Note
You can select a center frequency for each band.
You can change the center frequency in 1/3-oc-
tave steps, but you cannot select frequencies that
have intervals shorter than 1 octave among the
center frequencies of the three bands.
— When speakers are incorrectly connected.
(e.g., When a rear speaker is connected to
a subwoofer output.)
— When a speaker is connected to a power
amp delivering output higher than the
speaker’s maximum input power capabil-
ity.
If the microphone is placed in an unsuitable
position the measurement tone may become
loud and measurement may take a long time,
resulting in a drain on battery power. Be sure
to place the microphone in the specified loca-
tion.
Using the auto-equalizer
!
The auto-equalizer is the equalizer curve cre-
ated by auto TA and EQ (refer to Auto TA and
You can turn the auto-equalizer on or off.
1
Touch NEXT twice on the DSP function
menu.
2
#
Touch AUTO EQ.
You cannot use this function if auto TA and
EQ has not been carried out.
78
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
Available accessories
04
— The fader/balance settings return to the
center position. (Refer to page 72.)
— The equalizer curve switches to FLAT.
(Refer to page 77.)
— It will be adjusted automatically to high
pass filter setting for front, center and
rear speaker.
If you carry out auto TA and EQ when a pre-
vious setting of this already exists, the set-
ting will be replaced.
Before operating the auto TA and EQ
function
!
Carry out auto TA and EQ in as quiet a
place as possible, with the car engine and
air conditioning switched off. Also cut
power to car phones or portable telephones
in the car, or remove them from the car be-
fore carrying out auto TA and EQ. Sounds
other than the measurement tone (sur-
rounding sounds, engine sound, tele-
phones ringing etc.) may prevent correct
measurement of the car interior acoustic
characteristics.
!
Carrying out auto TA and EQ
Stop the car in a place that is as quiet
as possible, close all doors, windows and
the sun roof, and then turn the engine off.
If the engine is left running, engine noise may
prevent correct auto TA and EQ.
1
!
Be sure to carry out auto TA and EQ using
the supplied microphone. Using another
microphone may prevent measurement, or
result in incorrect measurement of the car
interior acoustic characteristics.
!
!
When front speaker is not connected, auto
TA and EQ cannot be carried out.
2
Fix the supplied microphone in the cen-
ter of the headrest of the driver’s seat, fa-
cing forward, using the belt (sold
separately).
The auto TA and EQ may differ depending on
where you place the microphone. If desired,
place the microphone on the front passenger
seat to carry out auto TA and EQ.
When this unit is connected to a power
amp with input level control, auto TA and
EQ may not be possible if you lower power
amp input level. Set the power amp’s input
level to the standard position.
When this unit is connected to a power
amp with an LPF, turn off the LPF on the
power amp before carrying out auto TA and
EQ. In addition, the cut-off frequency for
built-in LPF of an active subwoofer should
be set to the highest frequency.
The time alignment value calculated by
auto TA and EQ may differ from the actual
distance in the following circumstances.
However, the distance has been calculated
by computer to be the optimum delay to
give accurate results for the circum-
stances, so please continue to use this
value.
!
!
3
Turn the ignition switch to ON or ACC.
If the car’s air conditioner or heater is turned
on, turn it off. Noise from the fan in the air
conditioner or heater may prevent correct auto
TA and EQ.
— When the reflected sound within a vehi-
cle is strong and delays occur.
— When delays occur for low sounds due
to the influence of the LPF on active
subwoofers or external amps.
#
Press SRC to turn the source on if this unit is
turned off.
!
Auto TA and EQ changes the audio settings
as below:
79
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
04
Available accessories
4
Select the position for the seat on
error message is displayed. (Refer to Under-
which the microphone is placed.
11 Touch ESC to cancel the auto TA and EQ
mode.
#
If no position is selected before you start auto
TA and EQ, FRONT-L is selected automatically.
12 Store the microphone carefully in the
glove compartment.
5
off.
Press SRC and hold until the unit turns
Press and hold EQ to enter the auto TA
Store the microphone carefully in the glove
compartment or any other safe place. If the
microphone is subjected to direct sunlight for
an extended period, high temperatures may
cause distortion, color change or mal-
function.
6
and EQ measurement mode.
7
Plug the microphone into the micro-
phone input jack on the multi-channel pro-
cessor.
For details concerning operation, refer to the
multi-channel processor’s operation manual.
8
Touch START to start the auto TA and
EQ.
9
Get out of the car and close the door
within 10 seconds when the 10-second
count-down starts.
The measurement tone (noise) is outputted
from the speakers, and auto TA and EQ be-
gins.
#
When all speakers are connected, auto TA
and EQ is completed in about nine minutes.
#
#
To stop auto TA and EQ, touch STOP.
To cancel auto TA and EQ part way through,
touch BACK or ESC.
10 When auto TA and EQ is completed,
Complete is displayed.
When correct measurement of car interior
acoustic characteristics is not possible, an
80
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
Troubleshooting
Common
Symptom
Cause
Action (See)
Power doesn’t turn on.
The unit doesn’t operate.
Leads and connectors are incor-
rectly connected.
Confirm once more that all connections are
correct.
The fuse is blown.
Rectify the reason for the fuse blowing, then
replace the fuse. Be very sure to install a fuse
with the same rating.
the built-in microprocessor to oper-
ate incorrectly.
Operation with the remote con- The remote control operation mode Switch to the correct remote control mode.
trol isn’t possible.
is incorrect.
The unit does not operate cor-
rectly even when the appropriate
remote control buttons are
pressed.
The remote control code is incor-
rect.
Make sure the remote control selection
switch setting and code type setting are the
same.
Battery power is low.
Load new battery.
Some operations are prohibited
with certain discs.
Check by using another disc.
Playback is not possible.
The disc is dirty.
Clean disc. (Page 86)
The loaded disc is a type this unit
cannot play.
Check what type the disc is.
Non compatible video system disc
is loaded.
Change to a disc compatible to your video
system.
No sounds are heard.
Cables are not connected correctly. Connect the cables correctly.
The volume level will not rise.
The unit is performing still, slow mo- There is no sound during still, slow motion or
tion or frame-by-frame playback.
frame-by-frame playback.
There is no picture.
The parking brake cord is not con-
nected.
Connect a parking brake cord, and apply the
parking brake.
The parking brake is not applied.
Connect a parking brake cord, and apply the
parking brake.
The icon
is displayed, and op- The operation is prohibited for the
This operation is not possible.
eration is not possible.
disc.
The operation is not compatible
This operation is not possible.
with the disc’s organization.
The picture stops (pauses) and Reading of data has become impos- After stopping playback once, start playback
the unit cannot be operated.
sible during playback.
The volume level is low.
The attenuator is on.
once more.
There is no sound.
Volume level is low.
Adjust the volume level.
Turn the attenuator off.
Secure the unit firmly.
There is audio and video skip-
ping.
The unit is not firmly secured.
The picture is stretched, the as- The aspect setting is incorrect for
Select the appropriate setting for your display.
pect is incorrect.
the display.
When the ignition switch is
turned ON (or turned to ACC),
the motor sounds.
The unit is confirming whether a
disc is loaded or not.
This is a normal operation.
81
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
The rear view camera is not con-
nected.
Connect a rear view camera.
Press and hold VOLUME/MUTE to return to
Nothing is displayed.
CAMERA POLARITY is at incorrect the source display and then select the correct
The touch panel keys cannot be
used.
setting.
Problems during DVD playback
Symptom
Cause
Action (See)
Playback is not possible.
The loaded disc has a different re-
gion number from this unit.
Replace the disc with one featuring the same
A parental lock message is dis- Parental lock is on.
played and playback is not pos-
sible.
Turn parental lock off or change the level.
Parental lock cannot be can-
celed.
The code number is incorrect.
Input the correct code number. (Page 36)
You have forgotten your code num- Touch C 10 times to cancel the code number.
ber.
Dialog language (and subtitle
language) cannot be switched. multiple language recordings.
The DVD playing does not feature
You cannot switch among multiple languages
if they are not recorded on the disc.
You can only switch between items Switch using the disc menu.
indicated in the disc menu.
No subtitles are displayed.
The DVD playing does not feature
subtitles.
Subtitles are not displayed if they are not re-
corded on the disc.
You can only switch between items Switch using the disc menu.
indicated in the disc menu.
Playback is not with the audio
The DVD playing does not feature
Switching to a selected language is not possi-
language and subtitle language dialog or subtitles in the language
ble if the language selected in DVD SETUP is
settings selected in DVD SETUP. selected in DVD SETUP.
not recorded on the disc.
Switching the viewing angle is
not possible.
The DVD playing does not feature
scenes shot from multiple angles.
You cannot switch between multiple angles if
the DVD does not feature scenes recorded
from multiple angles.
You are trying to switch to multiple Switch between multiple angles when watch-
angle viewing of a scene that is not ing scenes recorded from multiple angles.
recorded from multiple angles.
The picture is extremely unclear/ The disc features a signal to prohibit Since this unit is compatible with the copy
distorted and dark during play- copying. (Some discs may have
back. this.)
guard analog copy protect system, when play-
ing a disc that has a signal prohibiting copy-
ing, the picture may suffer from horizontal
stripes or other imperfections when viewed
on some displays. This does not mean this
unit is malfunctioning.
Problems during Video CD playback
Symptom
Cause
Action
The PBC (playback control)
The Video CD playing does not fea- This operation is not possible with Video CDs
menu display cannot be called ture PBC.
up.
not featuring PBC.
Repeat play and track/time
search are not possible.
The Video CD playing features PBC. This operation is not possible with Video CDs
featuring PBC.
82
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
Problems during iPod playback
Symptom
Cause
Action
iPod doesn’t operate correctly.
Cables are incorrectly connected.
Disconnect the cable from iPod. Once iPod
main menu is displayed, connect the cable
again.
Reset the iPod.
The iPod version is old.
Update the iPod version.
Problems during multi-channel processor connection
Symptom
Cause
Action (See)
No sounds are heard.
The volume level will not rise.
Optical cables are not connected
correctly.
Connect the cables correctly.
Even if multi-channel audio is
Digital output setting is set to Line- Normally, set the digital output setting to
selected, 2-channel audio is out- ar PCM.
put.
Error messages
When you contact your dealer or your nearest Pioneer Service Center, be sure to have the error
message recorded.
Built-in DVD player
Message
Cause
Action
DIFFERENT REGION DISC
The disc does not have the same re- Replace the DVD video with one bearing the
gion number as this unit
Dirty disc
correct region number.
Clean disc.
ERROR-02-XX
Scratched disc
Replace disc.
The disc is loaded upside down
Electrical or mechanical
Check that the disc is loaded correctly.
Press RESET.
NON-PLAYABLE DISC
This type of disc cannot be played
by this unit
Replace the disc with one this unit can play.
The inserted disc does not contain Replace disc.
any files that can be played back
PROTECT
SKIPPED
TEMP
All the files on the inserted disc are Replace disc.
secured by DRM
The inserted disc contains WMA
files that are protected by DRM
Replace disc.
The temperature of this unit is out- Wait until the unit’s temperature returns to
side the normal operating range within normal operating limits.
83
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
USB audio player/USB memory
Message
Cause
Action
NO AUDIO
No songs
Transfer the audio files to the USB portable
audio player/USB memory and connect.
USB memory with security enabled Follow the USB memory instructions to dis-
is connected able the security.
SKIPPED
PROTECT
The connected USB portable audio Play an audio file not protected by Windows
player/USB memory contains WMA Media DRM 9/10.
files that are protected by Windows
Media DRM 9/10
All the files on the connected USB Transfer audio files not protected by Windows
portable audio player/USB memory Media DRM 9/10 to the USB portable audio
are protected by Windows Media
DRM 9/10
player/USB memory and connect.
N/A USB
The USB device connected to is not Connect a USB portable audio player or USB
supported by this unit.
memory that is USB Mass Storage Class
compliant.
CHECK USB
The USB connector or USB cable is Confirm that the USB connector or USB
short-circuited.
cable is not caught in something or da-
maged.
The connected USB portable audio Disconnect the USB portable audio player/
player/USB memory consumes USB memory and do not use it. Turn the igni-
more than 500 mA (maximum allow- tion switch to OFF, then to ACC or ON and
able current).
then connect the compliant USB portable
audio player/USB memory.
ERROR-19
Communication failure
Perform one of the following operations.
-Turn the ignition switch OFF and back ON.
-Disconnect the USB portable audio player/
USB memory.
-Change to a different source.
Then, return to the USB portable audio
player/USB memory.
ERROR-23
USB device is not formatted with
FAT16 or FAT32
USB device should be formatted with FAT16
or FAT32.
iPod
Message
Cause
Action
ERROR-11
Communication failure
Disconnect the cable from iPod. Once iPod
main menu is displayed, connect the cable
again.
Reset the iPod.
ERROR-21
ERROR-30
No Songs
STOP
Old version of iPod
iPod failure
Update the iPod version.
Reset the iPod.
No songs
Transfer the songs to iPod.
Select a list that contains the songs.
No songs in the current list
84
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
iPod is not charged but operates
correctly
Check if the connection cable for iPod
shorted out (e.g., not caught in metal ob-
jects). After checking, turn the ignition switch
OFF and back ON or disconnect the iPod and
connect again.
Error has occurred when connect-
ing the iPod to this unit
Reconnect the iPod.
Turn the ignition switch to OFF, then to ACC
or ON.
Update the iPod version.
Understanding auto TA and EQ error messages
When correct measurement of car interior acoustic characteristics is not possible using the auto
TA and EQ, an error message may appear on the display. If an error message appears, refer to the
table below to see what the problem is and the suggested method of correcting the problem. After
checking, try again.
Message
Cause
Action
Error. Please check MIC.
Microphone is not connected.
Plug the supplied microphone securely into
the jack.
Error. Please check front SP.,
Error. Please check FL SP.,
Error. Please check FR SP.,
Error. Please check center SP.,
Error. Please check rear SP.,
Error. Please check RL SP.,
Error. Please check RR SP.,
Error. Please check subwoofer
The microphone cannot pick up the ! Confirm that the speakers are connected
measuring tone of a speaker.
correctly.
! Correct the input level setting of the power
amp connected to the speakers.
! Set the microphone correctly.
Error. Please check noise.
The surrounding noise level is too
high.
! Stop your car in a place that is as quiet as
possible, and switch off the engine, air condi-
tioner or heater.
! Set the microphone correctly.
85
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
!
!
It may not be possible to play back some
DVD video discs.
It is not possible to play back DVD-ROM/
DVD-RAM discs.
Handling guideline of discs
and player
!
Use only conventional, fully circular discs.
Do not use shaped discs.
DVD-R/DVD-RW discs
!
!
!
Unfinalized DVD-R/-RW discs which have
been recorded with the Video format (video
mode) cannot be played back.
DVD-R/-RW discs which have been re-
corded with the Video Recording format
(VR mode) cannot be played back.
For more information about recording
mode, please contact manufacture of DVD
recorder or application.
!
!
Use 12-cm or 8-cm disc. Do not use an
adapter when playing 8-cm discs.
Do not insert anything other than a disc
into the disc loading slot. Discs which can
be played back are listed on Playable discs
Do not use cracked, chipped, warped, or
otherwise damaged discs as they may da-
mage the player.
!
!
AVCHD recorded discs
!
Do not touch the recorded surface of the
discs.
This unit is not compatible with discs re-
corded in AVCHD (Advanced Video Codec
High Definition) format. Do not insert
AVCHD discs. If inserted, the disc may not
be ejected.
!
!
Store discs in their cases when not in use.
Avoid leaving discs in excessively hot envir-
onments including under direct sunlight.
Do not attach labels, write on or apply che-
micals to the surface of the discs.
To clean a disc, wipe the disc with a soft
cloth outward from the center.
Condensation may temporarily impair the
player’s performance. Leave it to adjust to
the warmer temperature for about one
hour. Also, wipe any dump discs with a soft
cloth.
Playback of discs may not be possible be-
cause of disc characteristics, disc format,
recorded application, playback environ-
ment, storage conditions, and so on.
Road shocks may interrupt disc playback.
Read the precautions for discs before
using them.
!
!
!
CD-R/CD-RW discs
!
When CD-R/CD-RW discs are used, play-
back is possible only for discs which have
been finalized.
It may not be possible to play back CD-R/
CD-RW discs recorded on a music CD re-
corder or a personal computer because of
disc characteristics, scratches or dirt on
the disc, or dirt, condensation, etc., on the
lens of this unit.
Playback of discs recorded on a personal
computer may not be possible, depending
on the application settings and the environ-
ment. Please record with the correct for-
mat. (For details, contact the manufacturer
of the application.)
!
!
!
!
!
DVD discs
!
With some DVD video discs, it may not be
possible to use certain functions.
86
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
!
!
!
Playback of CD-R/CD-RW discs may be-
come impossible in case of direct exposure
to sunlight, high temperatures, or the sto-
rage conditions in the vehicle.
Titles and other text information recorded
on a CD-R/CD-RW disc may not be dis-
played by this unit (in the case of audio
data (CD-DA)).
!
ISO 9660 Level 1 and 2 compliant. Romeo
and Joliet file systems are both compatible
with this player.
Multi-session playback is possible.
Compressed audio files are not compatible
with packet write data transfer.
Only 64 characters from the beginning can
be displayed as a file name (including the
extension such as .wma or .mp3) or a folder
name.
!
!
!
Read the precautions with CD-R/CD-RW
discs before using them.
!
!
Folder selection sequence or other opera-
tion may be altered depending on the en-
coding or writing software.
Regardless of the length of blank section
between the songs of original recording,
compressed audio discs play with a short
pause between songs.
Dual Discs
!
Dual Discs are two-sided discs that have a
recordable CD for audio on one side and a
recordable DVD for video on the other.
Playback of the DVD side is possible with
this unit. However, since the CD side of
Dual Discs is not physically compatible
with the general CD standard, it may not be
possible to play the CD side with this unit.
Frequent loading and ejecting of a Dual
Disc may result in scratches on the disc.
Serious scratches can lead to playback pro-
blems on this unit. In some cases, a Dual
Disc may become stuck in the disc loading
slot and will not eject. To prevent this, we
recommend you refrain from using Dual
Disc with this unit.
!
!
File extensions such as .wma, .mp3 or .m4a
must be used properly.
Example of a hierarchy
!
!
: Folder
: Compressed audio file
1
2
Please refer to the information from the
disc manufacturer for more detailed infor-
mation about Dual Discs.
3
4
5
6
Compressed audio files on
the disc
Level 1
Level 2 Level 3 Level 4
!
!
This unit assigns folder numbers. The user
cannot assign folder numbers.
It is possible to play back up to 255 folders
on one disc.
!
Depending on the version of Windows
Media Player used to encode WMA files,
album names and other text information
may not be correctly displayed.
!
There may be a slight delay when starting
playback of audio files encoded with image
data.
87
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
!
!
!
Depending on the kind of USB portable audio
player/USB memory you use, this unit may
not recognize the USB audio player/USB
memory or audio files may not be played back
properly.
This unit can play back files in the USB porta-
ble audio player/USB memory that is USB
Mass Storage Class. However, copyright pro-
tected files that are stored in above-mentioned
USB devices cannot be played back.
You cannot connect a USB portable audio
player/USB memory to this unit via a USB
hub.
Compressed audio compatibility
WMA
!
Compatible format: WMA encoded by
Windows Media Player
!
!
!
Bit rate: 5 kbps to 320 kbps (CBR), VBR
Sampling frequency: 8 kHz to 48 kHz
Windows Media Audio 9 Professional, Loss-
less, Voice: No
MP3
!
!
Bit rate: 8 kbps to 320 kbps (CBR), VBR
Sampling frequency: 8 kHz to 48 kHz (8 kHz
to 48 kHz for emphasis)
!
Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3
(ID3 tag Version 2.x is given priority than
Version 1.x.)
Handling guideline and
supplemental information
!
!
M3u playlist: No
MP3i (MP3 interactive), mp3 PRO: No
!
Do not leave the USB portable audio
player/USB memory in direct sunlight for
extended amounts of time. Extended expo-
sure to direct sunlight can result in USB
portable audio player/USB memory mal-
function due to the resulting high tempera-
ture.
AAC
!
Compatible format: AAC encoded by
iTunes®
!
!
!
!
Bit rate: 8 kbps to 320 kbps (CBR)
VBR: No
Sampling frequency: 8 kHz to 44.1 kHz
Apple Lossless: No
!
!
Do not leave the USB portable audio
player/USB memory in high temperature.
Firmly secure the USB portable audio
player/USB memory when driving. Do not
let the USB portable audio player/USB
memory fall onto the floor, where it may be-
come jammed under the brake or accelera-
tor pedal.
USB audio player/USB memory
USB audio player/USB memory
compatibility
!
!
!
!
!
!
There may be a slight delay when starting
playback of audio files encoded with image
data.
Depending on the USB devices connected
to this unit, it may generate noise in the
radio.
Only 22 characters from the beginning can
be displayed as a file name (including the
extension) or a folder name when USB por-
table audio player/USB memory is selected
as a source.
USB version: 2.0, 1.1 and 1.0
USB data transfer rate: full speed
USB Class: MSC (Mass Storage Class) de-
vice
!
!
!
!
!
Protocol: bulk
Minimum amount of memory: 250 MB
Maximum amount of memory: 250 GB
File system: FAT32 and FAT16
Supply current: 500 mA
Notes
!
!
The text information of some audio files
may not be correctly displayed.
File extensions must be used properly.
!
Partitioned USB memory is not compatible
with this unit.
88
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
!
!
!
Up to 15 000 files on a USB portable audio
player/USB memory can be played back.
Up to 500 folders on a USB portable audio
player/USB memory can be played back.
Up to eight tiers directory on a USB porta-
ble audio player/USB memory can be
played back.
There may be a slight delay when starting
playback of audio files on a USB portable
audio player/USB memory with numerous
folder hierarchies.
!
!
Playback sequence of the audio file is the
same as recorded sequence in the USB de-
vice.
To specify the playback sequence, the fol-
lowing method is recommended.
1
Create the file name including numbers
that specify the playback sequence (e.g.,
001xxx.mp3 and 099yyy.mp3).
Put those files into a folder.
Record the folder containing files into the
USB device.
!
2
3
!
!
Do not connect anything other than the
USB portable audio player/USB memory.
Operations may vary depending on the
kind of USB audio player and a USB mem-
ory.
However, depending on the system environ-
ment, you cannot specify the file playback
sequence.
Compressed audio compatibility
WMA
The sequence of audio files on USB
memory
For USB portable audio players, the sequence is
different from that of USB memory and de-
pends on the player.
!
Compatible format: WMA encoded by
Windows Media Player
Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps
to 384 kbps (VBR)
Sampling frequency: 32 kHz to 48 kHz
Windows Media Audio 9 Professional, Loss-
less, Voice: No
!
!
!
Example of a hierarchy
: Folder
: Compressed audio file
MP3
!
!
Bit rate: 8 kbps to 320 kbps
Sampling frequency: 16 kHz to 48 kHz (32,
44.1, 48 kHz for emphasis)
1
2
!
Compatible ID3 tag version: 1.0, 1.1, 2.2,
2.3, 2.4 (ID3 tag Version 2.x is given priority
than Version 1.x.)
M3u playlist: No
MP3i (MP3 interactive), mp3 PRO: No
3
!
!
4
5
6
AAC
!
Compatible format: AAC encoded by
iTunes®
Level 1
Level 2 Level 3 Level 4
!
!
!
Sampling frequency: 11.025 kHz to 48 kHz
Transmission rate: 16 kbps to 320 kbps
Apple Lossless: No
!
01 to 05 represent assigned folder num-
bers. 1 to 6 represent the playback se-
quence. The user cannot assign folder
numbers and specify the playback se-
quence with this unit.
WAV
Compatible format: Linear PCM (LPCM),
MS ADPCM
!
89
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
!
!
Quantization bits: 8 and 16 (LPCM), 4 (MS
ADPCM)
Sampling frequency: 16 kHz to 48 kHz
(LPCM), 22.05 kHz to 44.1 kHz (MS AD-
PCM)
!
!
Sampling frequency: 8 kHz to 48 kHz
Compatible external subtitle file extension:
.srt
About handling the iPod
CAUTION
DivX video files
!
!
Pioneer accepts no responsibility for data lost
on the iPod even if that data is lost while
using this unit.
!
Depending on the file information composi-
tion such as the number of audio stream,
there may be a slight delay in the start of
playback on discs.
Do not leave the iPod in direct sunlight for ex-
tended amounts of time. Extended exposure
to direct sunlight can result in iPod malfunc-
tion due to the resulting high temperature.
Do not leave the iPod in a high temperature.
Firmly secure the iPod when driving. Do not
let the iPod fall onto the floor, where it may be-
come jammed under the brake or accelerator
pedal.
!
!
Some special operation may be prohibited
because of the composition of DivX files.
DivX files downloaded only from DivX part-
ner site are guarantee of proper operation.
Unauthorized DivX file may not operate
properly.
!
!
!
!
DRM rental file cannot be operated until
starting playing back.
This unit corresponds to a DivX file display
up to 1 590 minutes 43 seconds. Also,
search operation beyond this time limit is
prohibited.
For details, refer to the iPod’s manuals.
About iPod settings
!
!
If a file contains more than 4 GB, playback
is stopped on the way.
DivX VOD file playback requires ID code of
this unit to DivX VOD provider. About ID
File extensions such as .avi or .divx must be
used properly.
For more details about DivX, visit the follow-
ing site:
!
You cannot operate the iPod Equalizer on
Pioneer products. We recommend that you
set the iPod Equalizer to off, before con-
necting to this unit.
You cannot set Repeat to off on the iPod
when using this unit. Even if you set Repeat
to off on the iPod, Repeat is automatically
changed to All when connecting the iPod
to this unit.
!
!
!
Using the display correctly
DivX compatibility
CAUTION
!
Compatible format: DivX video format im-
plemented in relation to DivX standards
DivX Ultra format: No
DivX files without video data: No
Compatible audio codec: MP2, MP3, Dolby
Digital
!
If liquid or foreign matter should get inside
this unit, turn off the power immediately and
consult your dealer or the nearest authorized
PIONEER Service Station. Do not use the unit
in this condition because doing so may result
in a fire, electric shock, or other failure.
!
!
!
!
!
LPCM: No
Bit rate: 8 kbps to 320 kbps (CBR), VBR
90
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
!
!
If you notice smoke, a strange noise or smell,
or any other abnormal signs from the display,
turn off the power immediately and consult
your dealer or the nearest authorized
PIONEER Service Station. Using this unit in
this condition may result in permanent da-
mage to the system.
Do not disassemble or modify this unit, as
there are high-voltage components inside
which may cause an electric shock. Be sure
to consult your dealer or the nearest author-
ized PIONEER Service Station for internal in-
spection, adjustments or repairs.
display resulting in possible damage. Also,
if the display is cooled down by the cooler,
the screen may become dark, or the life
span of the small fluorescent tube used in-
side the display may be shortened.
Small black dots or white dots (bright dots)
may appear on the LCD screen. These are
due to the characteristics of the LCD
screen and do not indicate a problem with
the display.
!
!
At low temperatures, the LCD screen may
be dark for a while after the power is turned
on.
!
!
The LCD screen will be difficult to see if it is
exposed to direct sunlight.
Handling the display
When using a portable phone, keep the an-
tenna of the portable phone away from the
display to prevent disruption of the video by
the appearance of spots, colored stripes,
etc.
!
!
!
When the display is subjected to direct sun-
light for a long period of time, it will be-
come very hot resulting in possible
damage to the LCD screen. When not
using this unit, close the display and avoid
exposing it to direct sunlight.
The display should be used within the tem-
perature ranges shown below.
Storage temperature range: -4 °F to +176 °F
At temperatures higher or lower than the
operating temperature range the display
may not operate normally.
Keeping the display in good
condition
!
When removing dust from the screen or
cleaning the display, first turn the system
power off, then wipe with a soft dry cloth.
When wiping the screen, take care not to
scratch the surface. Do not use harsh or
abrasive chemical cleaners.
!
The LCD screen of this unit is exposed in
order to increase its visibility within the ve-
hicle. Please do not press strongly on it as
this may damage it.
Small fluorescent tube
!
!
!
Do not push the LCD screen with much
force as this may scratch it.
Be careful of fingers, long hair, and loose
articles of clothing which could possibly
get caught between the display and the
main body and cause serious injury.
A small fluorescent tube is used inside the
display to illuminate the LCD screen.
— The fluorescent tube should last for ap-
proximately 10 000 hours, depending on
operating conditions. (Using the display
at low temperatures reduces the service
life of the fluorescent tube.)
— When the fluorescent tube reaches the
end of its useful life, the screen will be
dark and the image will no longer be
projected. If this happens, consult your
dealer or the nearest authorized
Liquid crystal display (LCD) screen
!
If the display is near the vent of an air con-
ditioner when it is opened, make sure that
air from the air conditioner is not blowing
on it. Heat from the heater may damage
the LCD screen, and cool air from the cool-
er may cause moisture to form inside the
PIONEER Service Station.
91
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
Language code chart for DVD
Language (code), input code
Japanese (ja), 1001
English (en), 0514
French (fr), 0618
Spanish (es), 0519
German (de), 0405
Italian (it), 0920
Language (code), input code
Language (code), input code
Pashto, Pushto (ps), 1619
Quechua (qu), 1721
Rhaeto-Romance (rm), 1813
Kirundi (rn), 1814
Romanian (ro), 1815
Kinyarwanda (rw), 1823
Sanskrit (sa), 1901
Sindhi (sd), 1904
Sangho (sg), 1907
Serbo-Croatian (sh), 1908
Sinhalese (si), 1909
Slovak (sk), 1911
Slovenian (sl), 1912
Samoan (sm), 1913
Shona (sn), 1914
Somali (so), 1915
Albanian (sq), 1917
Serbian (sr), 1918
Siswati (ss), 1919
Sesotho (st), 1920
Sundanese (su), 1921
Swahili (sw), 1923
Tamil (ta), 2001
Guarani (gn), 0714
Gujarati (gu), 0721
Hausa (ha), 0801
Hindi (hi), 0809
Croatian (hr), 0818
Hungarian (hu), 0821
Armenian (hy), 0825
Interlingua (ia), 0901
Interlingue (ie), 0905
Inupiak (ik), 0911
Indonesian (in), 0914
Icelandic (is), 0919
Hebrew (iw), 0923
Yiddish (ji), 1009
Javanese (jw), 1023
Georgian (ka), 1101
Kazakh (kk), 1111
Greenlandic (kl), 1112
Cambodian (km), 1113
Kannada (kn), 1114
Kashmiri (ks), 1119
Kurdish (ku), 1121
Kirghiz (ky), 1125
Latin (la), 1201
Lingala (ln), 1214
Laothian (lo), 1215
Lithuanian (lt), 1220
Latvian (lv), 1222
Malagasy (mg), 1307
Maori (mi), 1309
Macedonian (mk), 1311
Malayalam (ml), 1312
Mongolian (mn), 1314
Moldavian (mo), 1315
Marathi (mr), 1318
Malay (ms), 1319
Maltese (mt), 1320
Burmese (my), 1325
Nauru (na), 1401
Chinese (zh), 2608
Dutch (nl), 1412
Portuguese (pt), 1620
Swedish (sv), 1922
Russian (ru), 1821
Korean (ko), 1115
Greek (el), 0512
Afar (aa), 0101
Abkhazian (ab), 0102
Afrikaans (af), 0106
Amharic (am), 0113
Arabic (ar), 0118
Assamese (as), 0119
Aymara (ay), 0125
Azerbaijani (az), 0126
Bashkir (ba), 0201
Byelorussian (be), 0205
Bulgarian (bg), 0207
Bihari (bh), 0208
Bislama (bi), 0209
Bengali (bn), 0214
Tibetan (bo), 0215
Breton (br), 0218
Catalan (ca), 0301
Corsican (co), 0315
Czech (cs), 0319
Telugu (te), 2005
Tajik (tg), 2007
Thai (th), 2008
Tigrinya (ti), 2009
Turkmen (tk), 2011
Tagalog (tl), 2012
Setswana (tn), 2014
Tonga (to), 2015
Turkish (tr), 2018
Tsonga (ts), 2019
Tatar (tt), 2020
Welsh (cy), 0325
Danish (da), 0401
Bhutani (dz), 0426
Esperanto (eo), 0515
Estonian (et), 0520
Basque (eu), 0521
Persian (fa), 0601
Finnish (fi), 0609
Fiji (fj), 0610
Faroese (fo), 0615
Frisian (fy), 0625
Twi (tw), 2023
Ukrainian (uk), 2111
Urdu (ur), 2118
Uzbek (uz), 2126
Vietnamese (vi), 2209
Volapük (vo), 2215
Wolof (wo), 2315
Xhosa (xh), 2408
Yoruba (yo), 2515
Zulu (zu), 2621
Nepali (ne), 1405
Norwegian (no), 1415
Occitan (oc), 1503
Oromo (om), 1513
Oriya (or), 1518
Irish (ga), 0701
Scots-Gaelic (gd), 0704
Galician (gl), 0712
Panjabi (pa), 1601
Polish (pl), 1612
92
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
Terms
the same as the Dolby Digital surround sound
system used in theaters.
AAC
AAC is short for Advanced Audio Coding and
refers to an audio compression technology
standard used with MPEG 2 and MPEG 4.
Dolby Pro Logic II
Dolby Pro Logic II can create five full-band-
width output channels from two-channel
sources. This new technology enables a dis-
crete 5-channel playback with 2 front chan-
nels, 1 center channel, and 2 rear channels. A
music mode is also available for 2-channel
sources in addition to the movie mode.
Aspect ratio
This is the width-to-height ratio of a TV screen.
A regular display has an aspect ratio of 4:3.
Wide screen displays have an aspect ratio of
16:9, providing a bigger picture for exceptional
presence and atmosphere.
DTS
This stands for Digital Theater Systems. DTS is
a surround system delivering multi-channel
audio from up to 6 independent channels.
Bit rate
This expresses data volume per second, or bps
(bits per second) units. The higher the rate,
the more information is available to reproduce
the sound. Using the same encoding method
(such as MP3), the higher the rate, the better
the sound.
Dynamic range control
Dolby Digital has a function for compressing
the difference between the loudest and softest
sounds: Dynamic range control. This control
ensures sounds with an increased dynamic
range are heard clearly even at low volume le-
vels.
Chapter
DVD titles are in turn divided into chapters
which are numbered in the same way as the
chapters of a book. With DVD video discs fea-
turing chapters, you can quickly find a desired
scene with chapter search.
ID3 tag
This is a method of embedding track-related
information in an MP3 file. This embedded in-
formation can include the track title, the ar-
tist’s name, the album title, the music genre,
the year of production, comments and other
data. The contents can be freely edited using
software with ID3 Tag editing functions.
Although the tags are restricted as to the num-
ber of characters, the information can be
viewed when the track is played back.
DivX
DivX is a popular media technology created by
DivX, Inc. DivX media files contain highly com-
pressed video with high visual quality that
maintains a relatively small file size. DivX files
can also include advanced media features like
menus, subtitles, and alternate audio tracks.
Many DivX media files are available for down-
load online, and you can create your own
using your personal content and easy-to-use
tools from DivX.com.
ISO9660 format
This is the international standard for the for-
mat logic of CD-ROM folders and files. For the
ISO9660 format, there are regulations for the
following two levels.
DivX Certified
DivX Certified products are officially tested by
the creators of DivX and guaranteed to play all
versions of DivX video, including DivX 6.
Level 1:
The file name is in 8.3 format (the name con-
sists of up to 8 characters, half-byte English
capital letters and half-byte numerals and the
“_” sign, with a file-extension of three charac-
ters).
Dolby Digital
Dolby Digital provides multi-channel audio
from up to 5.1 independent channels. This is
93
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
Level 2:
Multi-audio (Multilingual dialog)
Some DVDs feature dialog recorded in multi-
ple languages. Dialog in up to 8 languages
can be recorded on a single disc, letting you
choose as desired.
The file name can have up to 31 characters (in-
cluding the separation mark “.” and a file ex-
tension). Each folder contains less than 8
hierarchies.
Extended formats
Joliet:
Multi-session
Multi-session is a recording method that al-
lows additional data to be recorded later.
When recording data on a CD-ROM, CD-R or
CD-RW, etc., all data from beginning to end is
treated as a single unit or session. Multi-ses-
sion is a method of recording more than 2 ses-
sions on one disc.
File names can have up to 64 characters.
Romeo:
File names can have up to 128 characters.
Linear PCM (LPCM)/Pulse code
modulation
This stands for linear pulse code modulation,
which is the signal recording system used for
music CDs and DVDs. Generally, DVDs are re-
corded with higher sampling frequency and
bit rate than CDs. Therefore, DVDs can provide
higher sound quality.
Multi-subtitle
Subtitles in up to 32 languages can be re-
corded on a single DVD, letting you choose as
desired.
Optical digital output/input
m3u
By transmitting and receiving audio signals in
a digital signal format, the chance of sonic
quality deteriorating in the course of transmis-
sion is minimized. An optical digital output/
input is designed to transmit and receive digi-
tal signals optically.
Playlists created using the “WINAMP” soft-
ware have a playlist file extension (.m3u).
MP3
MP3 is short for MPEG Audio Layer 3. It is an
audio compression standard set by a working
group (MPEG) of the ISO (International Stan-
dards Organization). MP3 is able to compress
audio data to about 1/10th the level of a con-
ventional disc.
Packet write
This is a general term for a method of writing
on CD-R, etc., at the time required for a file,
just as is done with files on floppy or hard
discs.
MPEG
This stands for Moving Pictures Experts
Group, and is an international video image
compression standard. Some DVDs feature di-
gital audio compressed and recorded using
this system.
Parental lock
Some DVD video discs with violent or adult-or-
iented scenes feature parental lock which pre-
vents children from viewing such scenes. With
this kind of disc, if you set the unit’s parental
lock level, playback of scenes inappropriate for
children will be disabled, or these scenes will
be skipped.
Multi-angle
With regular TV programs, although multiple
cameras are used to simultaneously shoot
scenes, only images from one camera at a
time are transmitted to your TV. Some DVDs
feature scenes shot from multiple angles, let-
ting you choose your viewing angle as desired.
94
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
Playback control (PBC)
This is a playback control signal recorded on
Video CDs (Version 2.0). Using menu displays
provided by Video CDs with PBC lets you enjoy
playback of simple interactive software and
software with search functions. You can also
enjoy viewing high- and standard-resolution
still images.
Region number
DVD players and DVD discs feature region
numbers indicating the area in which they
were purchased. Playback of a DVD is not pos-
sible unless it features the same region num-
ber as the DVD player. This unit’s region
number is displayed on the bottom of the unit.
Title
DVD video discs have high data capacity, en-
abling recording of multiple movies on a sin-
gle disc. If, for example, one disc contains
three separate movies, they are divided into
title 1, title 2 and title 3. This lets you enjoy the
convenience of title search and other func-
tions.
VBR
VBR is short for variable bit rate. Generally
speaking CBR (constant bit rate) is more
widely used. But by flexibly adjusting the bit
rate according to the needs of audio compres-
sion, it is possible to achieve compression-
priority sound quality.
WMA
WMA is short for Windows Media™ Audio
and refers to an audio compression technol-
ogy that is developed by Microsoft
Corporation. WMA data can be encoded by
using Windows Media Player version 7 or
later.
Windows Media and the Windows logo are tra-
demarks or registered trademarks of Microsoft
Corporation in the United States and/or other
countries.
95
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
HPF:
Specifications
Frequency .......................... 50/63/80/100/125 Hz
Slope .................................... –12 dB/oct
Subwoofer (mono):
General
Power source ............................. 14.4 V DC (10.8 V to 15.1 V
allowable)
Frequency .......................... 50/63/80/100/125 Hz
Slope .................................... –18 dB/oct
Gain ...................................... +6 dB to –24 dB
Phase .................................. Normal/Reverse
Bass boost:
Grounding system ................... Negative type
Max. current consumption
..................................................... 10.0 A
Dimensions (W × H × D):
DIN
Gain ...................................... +12 dB to 0 dB
Chassis ..................... 178 mm × 100 mm × 162
mm
(7 in. × 3-7/8 in. × 6-3/8 in.)
Nose ........................... 171 mm × 97 mm × 9 mm
(6-3/4 in.× 3-7/8 in.× 3/8 in.)
Weight .......................................... 1.8 kg (4 lbs)
DVD Player
System .......................................... DVD video, Video CD, CD,
WMA, MP3, AAC, DivX sys-
tem
Usable discs .............................. DVD video, Video CD, CD,
CD-R/RW, DVD-R/RW
Region number ........................ 1
Signal format:
Display
Screen size/aspect ratio ....... 6.1 inch wide/16:9
(effective display area: 136
Sampling frequency ..... 44.1/48/96 kHz
Number of quantization bits
........................................... 16/20/24; linear
Frequency response ............... 5 Hz to 44 000 Hz (with DVD,
at sampling frequency 96
× 72 mm)
Pixels ............................................. 336 960 (1 440 × 234)
Display method ........................ TFT active matrix, transmis-
sive type
Color system .............................. NTSC
Durable temperature range (power off)
..................................................... -4 °F to +176 °F
kHz)
Signal-to-noise ratio ............... 97 dB (1 kHz) (IEC-A net-
work)
(CD: 96 dB (1 kHz) (IEC-A
network)) (RCA level)
Audio
Output level:
Maximum power output ....... 50 W × 4
50 W × 2/4 W + 70 W × 1/2
W (for subwoofer)
Video .................................... 1.0 Vp-p/75 W ( 0.2 V)
Number of channels .............. 2 (stereo)
MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10 (2ch
audio)
Continuous power output ... 22 W × 4 (1 kHz, 5% THD, 4
W load, both channels dri-
ven)
Load impedance ...................... 4 W to 8 W × 4
4 W to 8 W × 2 + 2 W × 1
Preout max output level ....... 4.0 V
Equalizer (3-Band Parametric Equalizer):
Low
(Windows Media Player)
AAC decoding format ............ MPEG-4 AAC (iTunes® en-
coded only) (.m4a)
DivX decoding format ............ Home Theater Ver. 3, 4, 5.2
(.avi, .divx)
Frequency ................ 40/80/100/160 Hz
Q Factor .................... 0.35/0.59/0.95/1.15 (+6 dB
when boosted)
USB
Specification .............................. USB 2.0 full speed
Supply current .......................... 500 mA
Maximum amount of memory
..................................................... 250 GB
File system .................................. FAT16, FAT32
MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11 (2ch
audio)
Gain ............................ 12 dB
Mid
Frequency ................ 200/500/1k/2k Hz
Q Factor .................... 0.35/0.59/0.95/1.15 (+6 dB
when boosted)
Gain ............................ 12 dB
High
(Windows Media Player)
Frequency ................ 3.15k/8k/10k/12.5k Hz
Q Factor .................... 0.35/0.59/0.95/1.15 (+6 dB
when boosted)
AAC decoding format ............ MPEG-4 AAC (iTunes® en-
coded only) (.m4a)
(Ver. 7.2 and earlier)
Gain ............................ 12 dB
96
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Additional Information
WAV signal format .................. Linear PCM & MS ADPCM
(Non-compressed)
FM tuner
Frequency range ...................... 87.9 MHz to 107.9 MHz
Usable sensitivity ..................... 8 dBf (0.7 µV/75 W, mono,
S/N: 30 dB)
Signal-to-noise ratio ............... 75 dB (IEC-A network)
AM tuner
Frequency range ...................... 530 kHz to 1 710 kHz (10
kHz)
Usable sensitivity ..................... 18 µV (S/N: 20 dB)
Signal-to-noise ratio ............... 65 dB (IEC-A network)
CEA2006 Specifications
Power output ............................. 14 W RMS × 4 Channels (4
W and ≦ 1 % THD+N)
S/N ratio ....................................... 91 dBA (reference: 1 W into
4 W)
Note
Specifications and the design are subject to mod-
ifications without notice due to improvements.
97
En
Download from Www.Somanuals.com. All Manuals Search And Download.
PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU
TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936
TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada
TEL: 1-877-283-5901
TEL: 905-479-4411
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
Blvd.Manuel Avila Camacho 138 10 piso
Col.Lomas de Chapultepec, Mexico, D.F. 11000
TEL: 55-9178-4270
先鋒股份有限公司
總公司 : 台北市中山北路二段44號13樓
電話 : (02) 2521-3588
先鋒電子（香港）有限公司
香港九龍尖沙咀海港城世界商業中心
9樓901-6室
Published by Pioneer Corporation.
Copyright © 2007 by Pioneer Corporation.
All rights reserved.
電話 : (0852) 2848-6488
Printed in Thailand
<KSNZX> <07K00000>
<CRB2528-A/N> UC
Download from Www.Somanuals.com. All Manuals Search And Download.
|