16:9 Rear Seat Entertainment Display
Owner’s Manual
AVD-W6200
This product conforms to new cord colors.
Los colores de los cables de este producto se conforman con un nuevo
código de colores.
Dieses Produkt entspricht den neuen kabelfarben.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
Please Read All of These Instructions Regarding Your Display
and Retain them for Future Reference
1. Read this manual fully and carefully before operating your display.
2. Keep this manual handy for future reference.
3. Pay close attention to all warnings in this manual and follow the instructions care-
fully.
4. Never allow others to use the system until they have read and understood the
operating instructions.
5. Do not install the display where it may (i) obstruct the driver’s vision, (ii) impair
the performance of any of the vehicle’s operating systems or safety features,
including airbags, or (iii) impair the driver’s ability to safely operate the vehicle.
6. As with any accessory in your vehicle’s interior, the display should not divert
your attention from the safe operation of your vehicle. If you experience difficul-
ty in operating the system or reading the display, please park safely before mak-
ing adjustments.
7. Do not attempt to install or service your display by yourself. Installation or ser-
vicing of the display by persons without training and experience in electronic
equipment and automotive accessories may be dangerous and could expose you
to the risk of electric shock or other hazards.
8. Please remember to wear your seat belt at all times while operating your vehicle.
If you are ever in an accident, your injuries can be considerably more severe if
your seat belt is not properly buckled.
9. If this product is installed in a place where it is visible to the vehicle’s driver, you
[
]
[
]
MUST always set the LOCATION to the FRONT setting. Failure to do so
could result in distracting images being potentially visible to the driver while the
vehicle is in motion.
If this product is installed in a place where it is not visible to the vehicle’s driver,
[
]
then you may choose the REAR location setting.
Use of this product is subject to any government laws regarding placement or use.
PIONEER does not accept any liability for any problems, damage or loss incurred
as a result of the product being used with an incorrect setting or in violation of
any government laws.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Fitting and Removing the Display
Precaution:
•
To prevent failure, be sure to turn the ignition switch or system power OFF before fitting or
removing the display. Also take care not to grip the screen or buttons too firmly or to drop the
display.
•
•
Do not let any water get on the terminals on the display or on the cable and do not allow the ter-
minals to be shorted by a metal object or the like. This can cause system breakdown.
Be careful not to touch terminals on the display or on the cable. Doing so may cause connection
failures. If any terminals are stained, wipe them with a clean dry cloth.
Note:
•
The mounting arm described below is sold separately. For more information on the installation,
refer to the instruction manual or consult your nearest dealer.
To fit the display
1. Fit part 1 of the display into the grooves 2 of the base.
Base
Connect the cable to the
display.
Mounting arm
(sold separately)
2. Slide the display until it clicks into place.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
To remove the display
• Pull the lock release lever 3 and hold in that position, then slide the display and
detach it from its base.
• To prevent theft of the display, remove the display when leaving the vehicle.
Base
Mounting arm
(sold separately)
Press the lock release button
while holding the display.
Keep holding the button and
unplug the connector.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
About This Product
• This product complies with the EMC Directives (89/336/EEC, 92/31/EEC) and
CE Marking Directive (93/68/EEC).
• Do not place the display in a position where it will impede the driver’s visibility or
affect the operation of your vehicle’s airbags or headrests.
Precaution
• Always keep the volume low enough for outside sounds to be audible.
• Protect the product from moisture.
In Case of Trouble
Should this product fail to operate properly, contact your dealer or the nearest authorized
Pioneer service facility.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using This Product
To Avoid Battery Exhaustion
Always run the vehicle engine while using this unit. Using this unit without running the
engine can result in battery drainage.
To Protect the LCD Screen of the Display
• Do not allow direct sunlight to fall on the Display when this unit is not being used.
Extended exposure to direct sunlight can result in LCD screen malfunction due to the
resulting high temperatures.
• When using a portable phone, keep the antenna of the portable phone away from the
Display to prevent disruption of the video by the appearance of spots, colored stripes,
etc.
When Viewing is Difficult, use [BRIGHTNESS] and [DIMMER] to Adjust
Due to its construction, the view angle of the LCD screen is limited. The viewing angle
(vertical and horizontal) can be increased, however, by using [BRIGHTNESS] to adjust
the black density of the video. When using for the first time, adjust the black density in
accordance with the viewing angle (vertical and horizontal) to adjust for clear viewing.
[DIMMER] can also be used to adjust the brightness of the LCD screen itself to suit your
personal preference.
About the RCA Video and Audio Outputs of this Unit
When you connect a separate piece of AV equipment such as another display to the RCA
video and audio output jacks of the hide-away unit, you can select the source for output
with the SOURCE button.
• The video and audio source of the RCA outputs of this unit cannot be selected indepen-
dently.
• Volume control buttons will have no effect even if operated.
CAUTION
Never position the display connected to the RCA output jack of the hide-
away unit so that the driver can view the picture while the vehicle is moving.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using This Product
To Ensure Safe Driving
This unit senses whether the parking brake is on or off. When installed in the FRONT, it is
arranged so that video cannot be viewed while the vehicle is moving. The various settings
and adjustments are also not possible while driving. (The following message will be dis-
played on the screen while the vehicle is moving.)
Stop the vehicle in a safe place, apply the parking brake and wait for the message to clear
before starting operation.
Note:
•
You cannot select wide mode while the message above is displayed on the screen. (Refer to page
12.)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Resetting the System
Resetting the Microprocessor
Pressing the RESET button lets you reset the microprocessor to its initial settings without
changing the setup function settings.
Reset the microprocessor in the following cases:
When using this product for the first time after installation.
When the product fails to operate properly.
When strange (incorrect) messages appear on the display.
• To reset the microprocessor, press the RESET button on the unit with a pen
tip or other pointed instrument.
RESET button
Resetting the Setup Function
The WIDE/MENU button and the RESET button let you erase all memorized settings and
return the setup function to their initial (factory) settings without resetting the micro-
processor. (Refer to the next page.)
1. Hold the WIDE/MENU down and press the RESET button.
2. Release the RESET button and hold down the WIDE/MENU button for 2
seconds.
3. Release the WIDE/MENU button.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Finder
Component Parts and Features
7 Display Unit
1 Signal receptor
5 Volume control (–/+) buttons
Adjust the volume of the built-in
speaker 8, or change setup items when
the setup function is displayed.
This receiver receives signals from a
remote control.
2 POWER button
Note:
Switches power ON/OFF.
•
Never set the volume so high that you
cannot hear outside traffic and emergency
vehicles.
3 DIMMER button
Selects the brightness level.
6 SOURCE button
4 WIDE/MENU button
Switches between sources.
Changes the method of enlarging 4:3
video to 16:9 video. Pressing this but-
ton for 2 seconds, and displayed the
setup function. Once the setup function
is displayed, its function is switched
each time the button is pressed.
7 RESET button
Resets the microprocessor.
8 Built-in speaker
Outputs sound from audio equipment
connected to this product.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
WARNING
If this product is installed in a place where it is visible to the vehicle’s driver,
you MUST always set the [LOCATION] to the [FRONT] setting. Failure to
do so could result in distracting images being potentially visible to the driver
while the vehicle is in motion.
If this product is installed in a place where it is not visible to the vehicle’s
driver, then you may choose the [REAR] location setting.
Use of this product is subject to any government laws regarding placement
or use.
PIONEER does not accept any liability for any problems, damage or loss
incurred as a result of the product being used with an incorrect setting or in
violation of any government laws.
Be sure to perform this setting. (Refer to page 16.)
Turn On Power
Remember to start the car engine before turning on the power to preserve battery life.
1. Start the car engine.
S
C
A
T
C
2. Turn on the system.
Press the POWER button.
To turn off the system, press the POWER button again.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Volume Adjustment
Adjust the volume of audio output from the built-in speaker.
• Raise or lower the speaker volume.
PAL
12
VOL
The volume of the built-in speaker can be adjusted in a range of 0 to 30. (The volume level
will be displayed for about 4 seconds.)
Selecting a Source
• Select the desired source.
Each press of the SOURCE button selects the desired source in the following order:
[VIDEO1] = [VIDEO2] = Exit to [VIDEO1]
Note:
•
[VIDEO1] and [VIDEO2] are audio and video from the AV equipment connected to the VIDEO1
or VIDEO2 input terminal. (Refer to page 21.)
•
Verify the correct connection with the AV equipment connected to VIDEO1 or VIDEO2.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Wide Screen Mode
You can change the way in which normal video (aspect ratio 4:3) enlarges to wide video
(16:9). Select wide modes to suit the kind of video you are viewing.
1. Display a source to view. (Refer to the previous page.)
2. Select a wide mode.
Each press of the WIDE/MENU button selects the wide mode in the following order:
[FULL] = [JUST] = [CINEMA] = [ZOOM] = [NORMAL] = Exit to [FULL]
Note:
•
•
Settings are stored for each source (VIDEO1, VIDEO2).
When video is viewed in a wide mode that does not match its original aspect ratio, it may appear
differently.
•
Remember that using the wide mode feature of this system for commercial or public viewing pur-
poses may constitute an infringement on the author’s rights protected by the Copyright Law.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Wide Modes Available
FULL
Video with an aspect ratio of 4:3
enlarges only horizontally. Enjoy
viewing video widened without
missing parts.
JUST
Video appears more extended hor-
izontally as it gets closer to both
edges of the screen. Because video
appears in about the same size as
regular video around the middle of
the screen, enjoy viewing it with-
out feeling out of place.
CINEMA
Video enlarges vertically with a
aspect ratio falling between FULL
and ZOOM. This wide mode is
suited for horizontally long video,
such as movies, in which titles are
displayed in black areas outside
the video.
ZOOM
Video with an aspect ratio of 4:3
enlarges with the same aspect ratio
in both vertical and horizontal
directions. This wide mode is suit-
ed for horizontally long video,
such as movies, in which titles
overlap the video.
NORMAL
Video with an aspect ratio of 4:3
appears without enlarging. Enjoy
viewing TV in the same video as it
is broadcast.
Note:
•
Video will appear roughened when viewed in CINEMA or ZOOM mode.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Setup Function
Dimmer Setting [DIMMER]
Viewing can become difficult after extended video viewing if the screen is too bright at
night or when ambient light darkens. You can select the brightness level from three set-
tings; HIGH, MID and LOW viewing.
1. Display a source to view. (Refer to page 11.)
2. Select a brightness level.
Each press of the DIMMER button selects the brightness level in the following order:
[HIGH] = [MID] = [LOW] = Exit to [HIGH]
Note:
•
Settings are stored by the source and the lighting switch (VIDEO1/VIDEO2, Car lights on/Car
lights off).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Setup Function
Entering the Setup Function
This system offers a number of functionality setup and adjustment features to make it easi-
er to use. Customize the settings to suit your taste and environment.
1. Display the setup function.
Press and hold the WIDE/MENU button for 2 seconds.
2. Select a function.
Each press of the WIDE/MENU button selects the desired function in the following order:
[BRIGHTNESS] = [CONTRAST] = [COLOR] = [HUE] = [LOCATION] =
[SPEAKER] = [COLOR SYSTEM] = Exit the setup function.
Note:
•
[HUE] cannot be adjusted for PAL video.
3. Adjust the setting level. / Switch the setting.
Pressing the Volume control (–/+) buttons adjusts the setting level or switches the setting.
Functions to be set
For the operations of the following functions, refer to the explanation above.
Settings for [BRIGHTNESS], [CONTRAST], [COLOR] and [HUE] are stored by the
source and the lighting switch (VIDEO1/VIDEO2, Car lights on/Car lights off).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Brightness [BRIGHTNESS]
You can make black appear darker or lighter (–24 to +24).
Contrast [CONTRAST]
You can make narrow or widen the gap between black and white (darken) (–24 to +24).
Color [COLOR]
You can make colors appear lighter or darker (–24 to +24).
Hue [HUE]
You can adjust the red or green of the picture (–24 to +24).
Note:
•
[HUE] cannot be adjusted for PAL video.
Location [LOCATION]
When using the display for the first time, set its mounting location.
[FRONT]: This product is installed on the dashboard or another location where the driver
can see the display.
[REAR]: This product is installed in a location for viewing by rear seat passengers (in a
location where the driver cannot see the display).
Note:
•
When [LOCATION] has been set to [FRONT], the video cannot be viewed while the vehicle is
moving. The setup function screen also cannot be displayed while the vehicle is moving. ([ATTEN-
TION] will be displayed while the vehicle is moving.)
Stop the vehicle in a safe place, apply the parking brake and wait for [ATTENTION] to be cleared
before starting operation.
Speaker [SPEAKER]
You can select [ON] or [OFF] for the audio from the built-in speaker.
Color System [COLOR SYSTEM]
You can select [NTSC] or [PAL] video for the color system. (The initial setting is [PAL].)
The setting is stored for each source (VIDEO1, VIDEO2).
Note:
•
If the setting of the color system is inadequate for the external component, images will not be cor-
rectly reproduced.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Display Correctly
CAUTION
• If moisture or foreign matter should get inside the unit, turn OFF the power
immediately and consult your dealer or the nearest authorized PIONEER
service facility. Using the unit in this condition may result in a fire, electric
shock or other failure.
• If you notice smoke, a strange noise or smell, or any other abnormal signs
from the display, turn OFF the power immediately and consult your dealer
or the nearest authorized PIONEER service facility. Using the unit in this
condition may result in failure of the system.
• Do not remove the rear cover of the display, as there are high-voltage com-
ponents inside which may cause an electric shock. Be sure to consult your
dealer or the nearest authorized PIONEER service facility for internal
inspection, adjustments or repairs.
Handling the Display
• When the display is not being used, never leave it under the direct sunlight or in extreme
temperatures.
• The display should be used within the temperature ranges shown below.
Operating temperature range: –10 to +50 °C
Storage temperature range:
–20 to +80 °C
At temperatures higher or lower than the operating temperature range, the display may
not operate normally.
• The LCD screen of this product is exposed to improve view ability in the vehicle. Do not
push the LCD screen strongly. This could break it.
• Do not touch the LCD screen. This could cause scratches or soiling.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
About the Liquid Crystal Display (LCD) Screen
• If the display is near the vent of an air conditioner when it is deployed, make sure that
air from the air conditioner is not blowing on it. Heat from the heater may break the
LCD screen, and cool air from the cooler may cause moisture to form inside the display
resulting in possible damage. Also, if the display is cooled down by the cooler, the
screen may become dark, or the life span of the small fluorescent tube used inside the
display may be shortened.
• Small black dots or white dots (bright dots) may appear on the LCD screen. These are
due to the characteristics of the LCD screen and do not indicate a problem with the dis-
play.
• At low temperatures, the LCD screen may be dark for a while after the power is turned
ON.
• The LCD screen will be difficult to see if it is exposed to direct sunlight.
Keeping the Display in Good Condition
• When removing dust from the screen or cleaning the display, first turn the system power
OFF, then wipe with a soft dry cloth.
• When wiping the screen, take care not to scratch the surface. Do not use harsh or abra-
sive chemical cleaners.
• Do not use a wet cloth for cleaning. Do not use organic solvents, such as benzine, thin-
ner.
About the Small Fluorescent Tube
• A small fluorescent tube is used inside the display to illuminate the LCD screen.
* The fluorescent tube is an expendable part and has a limited service life.
* The fluorescent tube should last for approximately 10,000 hours, depending on oper-
ating conditions. (Using the display at low temperatures reduces the service life of the
fluorescent tube.)
* When the fluorescent tube reaches the end of its useful life, the screen will be dark
and the image will no longer be projected. If this happens, consult your dealer or the
nearest authorized PIONEER service facility.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the System
CAUTION
• PIONEER does not recommend that you install or service your display your-
self. Installing or servicing the product may expose you to risk of electric
shock or other hazards. Refer all installation and servicing of your display to
authorized Pioneer service personnel.
• Secure all wiring with cable clamps or electrical tape. Do not allow any bare
wiring to remain exposed.
• Do not drill a hole into the engine compartment to connect the yellow lead of
the unit to the vehicle battery. Engine vibration may eventually cause the
insulation to fail at the point where the wire passes from the passenger com-
partment into the engine compartment. Take extra care in securing the wire
at this point.
• It is extremely dangerous to allow the display lead to become wound around
the steering column or gearshift. Be sure to install the display in such a way
that it will not obstruct driving.
• Make sure that wires will not interfere with moving parts of the vehicle, such
as the gearshift, parking brake or seat sliding mechanism.
• Do not shorten any leads. If you do, the protection circuit may fail to work
properly.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Note:
•
This unit is for vehicles with a 12-volt battery
•
If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be con-
nected to a terminal coupled with ignition switch
ON/OFF operations. If this is not done, the vehi-
cle battery may be drained when you are away
from the vehicle for several hours.
and negative grounding. Before installing it in a
recreational vehicle, truck, or bus, check the bat-
tery voltage.
•
•
•
•
To avoid shorts in the electrical system, be sure
to disconnect the ≠ battery cable before begin-
ning installation.
Refer to the owner’s manual for details on con-
necting other units, then make connections cor-
rectly.
Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
Route and secure all wiring so it cannot touch
any moving parts, such as the gear shift, hand-
brake and seat rails. Do not route wiring in
places that get hot, such as near the heater outlet.
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to
the vehicle body.
ACC position
No ACC position
CAUTION
•
Cords for this product and those for
other products may be different colors
even if they have the same function.
When connecting this product to
another product, refer to the supplied
Installation manuals of both products
and connect cords that have the same
function.
•
Don’t pass the yellow lead through a hole into
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
•
•
Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.
Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ity of the lead will be exceeded, causing over-
heating.
•
When replacing a fuse, be sure to use only fuses
of the rating prescribed on the fuse holder.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the System
Names and Functions of Connection Terminals
7 Hide-away Unit
1 VIDEO1 RCA video input (yellow)
Receives video, as from a VCR, DVD or
other AV equipment.
5 Power Supply
Receives the power cable supplied.
6 Display output (white)
2 VIDEO1 RCA audio input (white,
Connects to the display unit.
red)
7 RCA video output (yellow)
Connects to other AV equipment. Video
selected with this display is directed to this
terminal.
Receives stereo audio, as from a VCR,
DVD or other AV equipment.
3 VIDEO2 RCA video input (yellow)
Receives video, as from a VCR, DVD or
other AV equipment.
8 RCA audio output (white, red)
Connects to other AV equipment. Audio
selected with this display is directed to
these terminals.
4 VIDEO2 RCA audio input (white,
red)
Receives stereo audio, as from a VCR,
DVD or other AV equipment.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Power Cable
Hide-away Unit
Power cable
Fuse resistor
Orange/white
To lighting switch terminal.
Black (ground)
To vehicle (metal) body.
Fuse resistor
Red
To the electric terminal controlled by the ignition
switch (12 V DC) ON/OFF.
Do not connect this lead to power source terminals
to which power is continuously supplied. If the lead
is connected to such terminals, the battery may be
drained.
Fuse holder (4A)
Yellow
To the terminal always supplied with power regard-
less of ignition switch position.
Light green
Parking brake switch
Power supply side
Used to detect the ON/OFF status of the parking
brake. This lead must be connected to the power
supply side of the parking brake switch.
Connecting method
Ground side
Note:
Clamp the parking
brake switch power
supply side lead.
Clamp firmly
with needle-nosed
pliers.
•
The position of the parking brake switch
depends on the vehicle model. For details,
consult the vehicle Owner’s Manual or
dealer.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the System
Connection Diagram (VIDEO input)
Display Unit
White
3 m
VIDEO1 RCA audio input
(white, red)
VIDEO1 RCA video input
(yellow)
Hide-away Unit
VIDEO2 INPUT
VIDEO1 INPUT
Commercial RCA cable
(sold separately)
To audio output
Commercially
available portable
video component
with RCA output
To video output
Note:
•
This system has display mounting location [LOCATION] settings [FRONT/REAR]. Be sure to
complete these setting after the system has been installed. (Refer to page 16.)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the RCA Audio and Video Output
Hide-away Unit
RCA video output (yellow)
RCA audio output (white, red)
Commercial RCA cable
(sold separately)
Power cable
(Refer to page 22.)
To audio input (R)
To audio input (L)
Second display, video
deck, etc.
To video input
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
CAUTION
• For instructions on how to mount the display, consult your dealer.
• Do not install the display where it may (i) obstruct the driver’s vision, (ii)
impair the performance of any of the vehicle’s operating systems or safety
features, including airbags, or (iii) impair the driver’s ability to safely oper-
ate the vehicle.
• PIONEER does not recommend that you install or service your display your-
self. Installing or servicing the product may expose you to risk of electric
shock or other hazards. Refer all installation and servicing of your display to
authorized PIONEER service personnel.
• Install the display between the driver’s seat and front passenger seat so that
it will not be hit by the driver or passenger if the vehicle brakes sharply.
• Do not install the display in a position where the fully opened air bag will be
obstructed by it.
• Do not install the display in a place where it will impair the performance of
any of the vehicle’s operating systems, including airbags and headrests.
• Make sure there is nothing behind the panels when drilling holes in them. Be
careful not to damage fuel lines, brake lines or power cables.
• When using screws, do not allow them to come into contact with any electri-
cal lead. Vibration may damage wires, leading to a short circuit or other
damage to the vehicle.
• It is extremely dangerous to allow the display lead to become wound around
the steering column or shift lever. Be sure to install the display in such a way
that it will not obstruct driving.
• Make sure that leads cannot get caught in a door or the sliding mechanism of
a seat, resulting in a short circuit.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
• If this product is installed in a place where it is visible to the vehicle’s driver,
you MUST always set the [LOCATION] to the [FRONT] setting. Failure to
do so could result in distracting images being potentially visible to the driver
while the vehicle is in motion.
If this product is installed in a place where it is not visible to the vehicle’s
driver, then you may choose the [REAR] location setting.
Use of this product is subject to any government laws regarding placement
or use.
PIONEER does not accept any liability for any problems, damage or loss
incurred as a result of the product being used with an incorrect setting or in
violation of any government laws.
• To ensure proper installation, use the supplied parts in the manner specified.
If any parts other than the supplied ones are used, they may damage internal
parts of the unit or they may work loose and the unit may come off.
When the Display is Installed in the Front
• To ensure safe driving, be sure to install the display in a position that meets
the following conditions.
* Where it does not obstruct the driver’s vision and impede the safe opera-
tion of the vehicle.
* Where the front of the car is within the driver’s field of vision when look-
ing at the display.
* Where the display does not protrude above the front of the hood as viewed
by the driver.
Before Installing and Fixing
• Make temporary connections first to check that the unit and system are working properly.
• Press the RESET button with the tip of a ball-point pen or similar object, when a con-
nection is completed.
Before Affixing the Adhesive Tape
• Make sure the surface is free of moisture, dust, grime, oil, etc. before affixing the tape.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installing the Hide-away Unit
Installation Precautions
•
Never install in locations such as the following because of the danger of malfunction due to high
temperatures or humidity:
* Locations such as a dashboard or rear tray where there is exposure to direct sunlight.
* Near heater outlets.
* Near doors, etc., where there is danger of exposure to rain.
When installing under the front seat, make sure there is no hindrance to sliding of the seat.
Direct installation on the carpet is possible if the hard Velcro tape will adhere to the carpet. Do not
use the soft Velcro tape in this case.
•
•
Hide-away Unit Installation
Adhere the hard Velcro tape (supplied) to the bottom of the hide-away unit and adhere the
soft Velcro tape (supplied) to the installation location.
Hide-away Unit
Velcro tape (hard)
Velcro tape (soft)
Car mat
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General
Power source ...................................................................... 14.4 V DC (10.8 — 15.1 V allowed)
Grounding system ................................................................ Negative type
Max. current consumption .................................................. 2.0 A
Display Unit
Screen size/Aspect ratio ...................................................... 6.5 inch wide/16:9
(effective display area: 143.75 × 76 mm)
Pixels .................................................................................... 336,960 (234 × 1,440)
Type .................................................................................... TFT active matrix, transmissive type
Color system ........................................................................ NTSC/PAL compatible
Operating temperature range .............................................. –10 — +50 °C
Storage temperature range .................................................. –20 — +80 °C
Built-in Speaker.................................................................... ø 36 mm
Dimensions .......................................................................... 188 (W) × 114 (H) × 32 (D) mm
Weight ................................................................................ 430 g
Hide-away Unit
External video input level .................................................... 1 Vp-p/75 Ω
External audio input level .................................................... 1 V/22 kΩ
Max. output impedance ........................................................ 1 Vp-p/75 Ω
External audio max. output level ........................................ 1 V/1 kΩ
Dimensions .......................................................................... 104 (W) × 85 (H) × 26 (D) mm
Weight ................................................................................ 570 g
Note:
•
The specifications and design are subject to change without prior notice. Products purchased may differ in
details from illustrations in this manual.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936
TEL: 65-6472-1111
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
TEL: (905) 479-4411
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
Blvd.Manuel Avila Camacho 138 10 piso
Col.Lomas de Chapultepec, Mexico, D.F. 11000
TEL: 55-9178-4270
Published by Pioneer Corporation.
Copyright © 2003 by Pioneer Corporation.
All rights reserved.
Publication de Pioneer Corporation.
Copyright © 2003 Pioneer Corporation.
Tous droits de reproduction et de traduction
réservés.
Printed in Japan
Imprimé au Japon
<KKYNF/03B00001>
<CRD3747-A> EW
Download from Www.Somanuals.com. All Manuals Search And Download.
|
