Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTICE
RECORD THE MODEL NUMBER AND SERIAL NUMBERS OF THIS EQUIPMENT BELOW.
THE NUMBERS ARE ON THE REAR.
TAD-M600
MODEL NO.
SERIAL NO.
KEEP THESE NUMBERS FOR FUTURE USE.
D1-4-2-6-2*_A1_En
WARNING
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which
This equipment is not waterproof. To prevent a fire
or shock hazard, do not place any container filled
with liquid near this equipment (such as a vase or
flower pot) or expose it to dripping, splashing, rain
requires repair will be charged for even during the
or moisture.
D3-4-2-1-3_B_En
warranty period.
K041_En
CAUTION
WARNING
To prevent fire hazard, the Class 2 Wiring Cable
should be used for connection with speaker, and
should be routed away from hazards to avoid
damage to the insulation of the cable.
Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230 V
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
or 120 V) written on the rear panel.
D3-4-2-1-4_A_En
CAUTION
The POWER switch on this unit will not completely
shut off all power from the AC outlet. Since the
power cord serves as the main disconnect device for
the unit, you will need to unplug it from the AC outlet
to shut down all power. Therefore, make sure the
unit has been installed so that the power cord can
be easily unplugged from the AC outlet in case of an
accident. To avoid fire hazard, the power cord should
also be unplugged from the AC outlet when left
unused for a long period of time (for example, when
The equipment should be disconnected by removing
the mains plug from the wall socket when left unused
for a long period of time (for example, when on
vacation).
D3-4-2-2-1a_A1_En
on vacation).
D3-4-2-2-2a_A_En
WARNING: Handling the cord on this product or
cords associated with accessories sold with the
product will expose you to chemicals listed on
proposition 65 known to the State of California and
other governmental entities to cause cancer and
birth defect or other reproductive harm.
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
Wash hands after handling
D36-P4_A_En
damaged, ask your dealer for a replacement.
S002*_En
Download from Www.Somanuals.com. All Manuals Search And Download.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will
provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often
undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s
Consumer Electronics Group recommend you avoid
prolonged exposure to excessive noise. This list of
sound levels is included for your protection.
Selecting fine audio equipment such as the unit
you’ve just purchased is only the start of your
musical enjoyment. Now it’s time to consider how
you can maximize the fun and excitement your
equipment offers. This manufacturer and the
Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that
lets the sound come through loud and clear without
annoying blaring or distortion-and, most importantly,
without affecting your sensitive hearing.
Decibel
Level Example
30 Quiet library, soft whispers
40 Living room, refrigerator, bedroom away from traffic
50 Light traffic, normal conversation, quiet office
60 Air conditioner at 20 feet, sewing machine
70 Vacuum cleaner, hair dryer, noisy restaurant
80 Average city traffic, garbage disposals, alarm clock
at two feet.
Sound can be deceiving. Over time your hearing
“comfort level” adapts to higher volumes of sound.
So what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by
setting your equipment at a safe level BEFORE your
hearing adapts.
THE FOLLOWING NOISES CAN BE DANGEROUS
UNDER CONSTANT EXPOSURE
90 Subway, motorcycle, truck traffic, lawn mower
100 Garbage truck, chain saw, pneumatic drill
120 Rock band concert in front of speakers,
thunderclap
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it
comfortably and clearly, and without distortion.
140 Gunshot blast, jet plane
180 Rocket launching pad
Once you have established a comfortable sound
level:
• Set the dial and leave it there.
Information courtesy of the Deafness Research Foundation.
Taking a minute to do this now will help to prevent
hearing damage or loss in the future. After all, we
want you listening for a lifetime.
S001_En
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Thank you for buying this TAD product. Please read through these operating instructions so you will know how to operate
your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.
INTRODUCTION ...................................................................................................................................................6
Features.............................................................................................................................................................................6
BEFORE YOU START............................................................................................................................................7
Checking what’s in the box..............................................................................................................................................7
Controls and displays.......................................................................................................................................................7
INSTALLATION AND CONNECTIONS ..................................................................................................................8
Installation.........................................................................................................................................................................8
How to install ....................................................................................................................................................................................8
Adjusting the spike height...............................................................................................................................................................9
Connecting your equipment..........................................................................................................................................10
Connecting to the Pre-Amplifier....................................................................................................................................................10
Bi-wire connection..........................................................................................................................................................................11
Connecting to the speaker system................................................................................................................................................12
Connecting the power cord ...........................................................................................................................................................13
TO BEGIN PLAYBACK ........................................................................................................................................14
Before turning on the power..........................................................................................................................................................14
Playback ..........................................................................................................................................................................................14
Protection circuit ............................................................................................................................................................................14
TROUBLESHOOTING..........................................................................................................................................15
SPECIFICATIONS ................................................................................................................................................16
Maintenance ...................................................................................................................................................................................17
TAD-M600
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Inspiring the joy of listening
Technical Audio Devices Laboratories, Inc. (TADL) grew from the spirit to discover technologies to perfectly recreate the pure
sound of live performances with uncompromising craftsmanship. We have inherited our philosophy from Bart Locanthi—
recognized across the globe as the ultimate sound technologist—who believed that genuine technology is true to the basics
and that genuine technology places greater importance on sound quality than on technology for its own sake.
At TADL, we are honing our technology to create equipment that reproduces musical sounds that evoke both the energy and
impact of live music.
Features
Symmetry: Duallogic-Circuit Technology
In order to drive the speaker diaphrams correctly, it is crucial that the positive and negative current paths in the voice coils
be precisely symmetrical. Toward the end of achieving this perfect balance, we have incorporated symmetrical design in the
current mode, electrical circuits, and speaker structure.
Damping technology: Vibration-Absorber Technology
Improvements in the quality of vibration damping have been achieved by using cast iron as a low-resonance material for
the chassis, adopting an adjustable point-support structure for the spikes and a 10 mm-thick aluminum vibration damper
between the transformer and chassis.
Low center of gravity: Lower Weight-Balanced Frame
The monocoque chassis is constructed from 35 kg of cast iron in order to produce a massive and stable foundation. In
addition, the TAD-M600 has adopted a wide-tread chassis structure by locating the legs on the outer edges of its body, further
lowering its relative center of gravity.
Drive power: 600 W/4 rated output
Ω
A balanced-amplifier connection has been used to combine a 5-parallel push-pull amplifier with multi-emitter transistors
producing brilliant high-frequency characteristics, so that the TAD-M600 can output 600 W/4 , 300 W/8 with ease.
Ω
Ω
High-capacity power source
A power transformer consisting of two El 133 x 85 transformers and a high-capacity filter condenser consisting of four
33 000 μF are used to create a high-power source strong enough to accurately drive the speakers even at high output levels.
Protection circuit
In the event of a short circuit in the speaker terminals, electrical overload, or abnormal heating due to a contingency, the
protection circuit is activated. When activated, this circuit shuts off the power to the amp in order to prevent further heating,
while informing the user through the color of the power indicator light. This protection circuit function assures your amplifier
and speakers of safety from damage resulting from such anomalies.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE yOU START
Checking what’s in the box
Please check that you have received the following supplied accessories in the accessory box.
Power cord x 1
Hexagon wrench x 1
'
'
Spike base template x 1
Operating Instructions (this document)
'
'
Spike bases x 4
'
Controls and displays
Front panel
Rear panel
INPUT
(BALANCED)
SPEAKERS
A
B
CLASS
2
WIRING
OFF
ON
2
1
3
4
5
1. Power indicator
3. INPUT terminal (BALANCED)
Indicates whether the power is turned on or off. The indicator
will light red during start up or if there is a malfunction. The
indicator will light yellow when the unit is ready to operate.
If the power indicator light turns from yellow to red, turn off
the power and refer to Protection circuit on page 14. If the
trouble is still not resolved, ask your dealer.
Connect to Pre-Amplifier.
4. AC IN connector
Connect the accessory power cord here.
5. SPEAKERS terminals
Connect speakers with impedance of 4 to 16
.
Ω
Ω
2. Power switch
Press to turn the power on/off. Flip the switch to the right to
turn the power on; flip the switch to the left to turn the power
off.
TAD-M600
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTIONS
Installation
WARNING
As the TAD-M600 is a large and heavy unit, make sure to move, unpack and install with four or more people.
When installing, choose a level and flat surface that can sufficiently withstand the weight of this unit. Failure to do so
could cause the unit to fall, resulting in an accident.
'
'
It is recommended that the TAD-M600 be installed directly on a solid floor surface. If installed on a shelf, the user is
responsible for confirming that the location is fully able to support the heavy weight of the amplifier.
To promote heat-emission, do not put objects on top of the TAD-M600 or cover with a sheet (such as cloth or curtains)
while operating. Failure to do so could cause the unit to malfunction through abnormal heating.
'
Leave 60 cm (2 ft.) open
TAD-M600
CAUTION
As the TAD-M600 emits a large amount of heat, do not place this unit on top of soft surfaces (such as carpeting or
cushions) or in small spaces.
'
How to install
In order to improve sound quality and prevent damage to the floor or other installation surface, please use the accessory
spike bases.
1. Place the provided spike bases on the area of the installation site where the spikes will contact.
Lay down the spike base template and place the spike bases on the corners of the template to accurately locate the
spike bases.
Spike base
Spike base template
2. Remove the spike base template and place the TAD-M600.
Remove the spike base template carefully, taking care not to move the spike bases.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the spike height
1. Remove the cover on the rear right leg of the TAD-M600 as indicated below.
A
2. Insert the provided hexagon wrench and adjust the spike height so that the TAD-M600 does not wobble.
CLASS
2
WIRIN
G
3. Replace the cover removed in step 1.
TAD-M600
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your equipment
CAUTION
Do not turn on the power switch to the TAD-M600 or the other components until all connections have been completed.
'
We recommend that you place the speakers at the desired location before performing connections. Use commercially
available speaker cables for connections. When connecting other components, make sure to turn the power off and unplug
the other components before connecting.
TAD-M600
INPUT
(BALANCED)
SPEAKERS
A
B
CLASS
2
WIRING
To balance output terminal
To speaker terminal
Speaker
Pre-Amplifier
Connecting to the Pre-Amplifier
Connect a balance cable with an XLR plug (sold separately) to the INPUT (BALANCED) terminal of the TAD-M600 and the
Pre-Amplifier’s balance output terminal.
INPUT (BALANCED) terminal
INPUT
(XLR-3-31 equivalent)
1: Ground
2: Hot
3: Cold
2
1
(BALANCED)
3
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Bi-wire connection
The bi-wire connection uses two speaker cables on one amplifier to connect to the speaker’s low-frequency input terminal
and high-frequency input terminal.
In order to connect speakers to this unit using a bi-wire connection, the speakers must be bi-wiring compliant. Align the High
and Low wires correctly to connect.
[An example of connections made to a speaker system with bi-wire connection terminals]
Pre-Amplifier
To balance output terminal
To balance output terminal
TAD-M600
TAD-M600
INPUT
INPUT
(BALANCED)
(BALANCED)
SPEAKERS
SPEAKERS
A
B
A
B
CLASS
2
WIRING
CLASS
2
WIRING
High
Low
High
Low
Rear side of bi-wiring
compliant speakers
Rear side of bi-wiring
compliant speakers
Note
SPEAKERS A terminals and SPEAKERS B terminals produce the same output. High and Low connectors can be made to
either terminals A or B.
CAUTION
When using bi-wire connections, make sure to remove the short bar connectors on the High-Low terminals of the
speakers to prevent negative effects on the amplifier. Refer to the operating instructions of your speaker system for further
information.
'
TAD-M600
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the speaker system
CAUTION
The input terminals of speaker systems have a negative (–) pole and a positive (+) pole. Make sure to align these poles
correctly when connecting to the speaker terminals of the TAD-M600.
'
Make sure to use speakers with an impedance of 4 to 16
.
Ω
'
'
Ω
Use speaker cables with a large electrical capacity and make sure no warps or shorts are present. Using speaker cables
with a small electrical capacity or making imperfect connections could affect the sound quality of your speakers or cause
abnormal heating and shortage.
Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any of the bare
speaker wire touches the back panel it may cause the power to cut off as a safety measure.
These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric shock when connecting or
disconnecting the speaker cables, disconnect the power cord before touching any uninsulated parts.
'
'
How to connect the speaker system
Connect the positive (+) terminal of the speaker system to the positive (+) terminal of the TAD-M600.
Connect the negative (–) terminal of the speaker system to the negative (–) terminal of the TAD-M600.
Connecting the speaker cable
1. Remove 15 mm (1/ in.) of the protective insulation to the speaker cable, and twist the core wires together.
10
2. Turn the speaker terminal knob to the left. (
)
The terminal knob will slide out and create a gap.
3. Insert the speaker wire into the gap and turn the terminal knob to the right to tighten. (
)
1
2
3
Speaker terminal
15 mm (1/10 in.)
Speaker cable
Terminal knob
Y lug terminal
Banana plug
Y lug terminals and banana plugs may also be connected (refer to your
plug’s operation manual for further information).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the power cord
Once all connections have been made, plug in the power cord to a power outlet (AC 120 V).
• Although the power cord to the TAD-M600 is removable, do not attempt to use a power cord
other than the supplied cord.
• Connect the power plug to a power outlet and turn the power switch on to power up the TAD-M600. Upon power up, there
will be an eight second mute period. While muted, the power indicator will light red. The power indicator will turn yellow
once the TAD-M600 is ready to be operated.
• When not using the TAD-M600 for a long period of time (due to travel or other reasons), be sure to unplug the power cord
from the power outlet.
• Always turn the power switch off before unplugging the power cord to the TAD-M600.
How to connect the power cord
1. Connect the supplied power cord to the AC IN connector of the TAD-M600.
2. Connect the power plug to a power outlet (AC 120 V).
TAD-M600
INPUT
Power outlet
(BALANCED)
Wider opening
2
SPEAKERS
A
B
CLASS
2
WIRING
1
Power cord (2-pin) (supplied)
CAUTION
As the TAD-M600 has high power consumption, be sure to connect the plug to a power outlet providing sufficient electrical
capacity. (Connecting to a power outlet with low electrical capacity could result in abnormal heating of the plug connection.)
Handle the power cord by the plug part. Do not pull out the plug by tugging the cord, and never touch the power cord when
your hands are wet, as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, or other
object on the power cord or pinch the cord in any other way. Never make a knot in the cord or tie it with other cables. The
power cords should be routed so that they are not likely to be stepped on. A damaged power cord can cause a fire or give you
an electric shock. Check the power cord once in a while. If you find it damaged, ask your dealer for a replacement.
'
'
TAD-M600
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TO BEgIN PLAyBACk
Before turning on the power
Make sure that the input terminals and output terminals are securely connected.
Playback
1. Turn the volume knob of the Pre-Amplifier to its lowest setting.
2. Turn the Pre-Amplifier’s power on.
3. Turn the TAD-M600’s power on.
The power indicator will light red for eight seconds. The light will turn yellow once the TAD-M600 is ready to operate.
Use the Pre-Amplifier’s volume knob to adjust the volume.
4. To turn off the unit after use, first turn the volume knob of the Pre-Amplifier to its lowest setting, then turn off both the
Pre-Amplifier and the TAD-M600.
Protection circuit
The TAD-M600 is provided with a built-in automatic protection circuit to prevent electrical damage to the amplifier and
speakers. When the protection circuit operates, the power indicator will light red, and no sound will be produced from the
speakers. The protection circuit may operate in the following circumstances:
When power is first turned ON
'
In order to silence potential noise during startup, the muting circuit operates for eight seconds; the indicator lights red
during this time.
In event of malfunction
'
In the event of a short-circuit between speaker terminals, excessive load, or abnormal heat generation, the protection
circuit will operate and the indicator will light red. The protection circuit is of the auto reset type. In the event the protection
circuit operates due to a malfunction, turn off the power, eliminate the source of the malfunction, and turn the power on
again.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTINg
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this
component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components
and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your
dealer.
Symptom
Possible cause
Remedy
Power does not turn
on.
The power plug is not connected to the
power outlet.
Firmly plug in the power cord to the power
outlet.
'
'
'
'
The power cord is not connected to the AC
IN connector of the TAD-M600.
Firmly plug in the power cord to the AC IN
connector.
No sound output.
The speaker cable is disconnected or is not
connected correctly.
Firmly connect the speaker cable.
'
'
'
'
'
'
The terminal or the speaker cable plug is
dirty.
Clean the terminal and plug.
The power indicator light is red.
Refer to Protection circuit on page 14 and
eliminate the cause.
TAD-M600
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Amplifier Section
#
Power output ...................................................................................................................600 W (20 Hz to 20 kHz, T.H.D., 0.2 %, 4
300 W (20 Hz to 20 kHz, T.H.D., 0.2 %, 8
)
Ω
)
Ω
)
Ω
Rated distortion ........................................................................................................Less than 0.03 % (20 Hz to 20 kHz, 300 W, 4
Signal-to-Noise Ratio (IHF, short circuited, A network) .......................................................................................... 125 dB or higher
+0
–1
Frequency response ........................................................................................................................................ 1 Hz to 100 kHz,
dB
Gain..............................................................................................................................................................................................29.5 dB
Input terminal (Sensitivity/ Impedance) ........................................................................................................................ 1.5 V / 220 k
Ω
Power section/miscellaneous
#
Power requirements.....................................................................................................................................................AC 120 V, 60 Hz
Power consumption ..................................................................................................................................................................... 520 W
Dimensions...................................................................................................................... 516 mm (W) × 297 mm (H) × 622 mm (D)
/
(20 5/16 in. (W) x 11 11 16 in. (H) x 24 1/2 in. (D))
Dimensions (When using spike bases)......................................................................... 516 mm (W) × 307 mm (H) × 622 mm (D)
1
/
16 in. (H) x 24 1/2 in. (D))
5
(20 /16 in. (W) x 12
Weight ......................................................................................................................................................................... 90.0 kg (198.4 lb)
Accessories
#
Power cord.............................................................................................................................................................................................1
Spike bases ............................................................................................................................................................................................4
Spike base template..............................................................................................................................................................................1
Hexagon wrench....................................................................................................................................................................................1
Operating Instructions (this document)..............................................................................................................................................1
Note
Specifications and the design are subject to possible modifications without notice, due to improvements.
'
16
Download from Www.Somanuals.com. All Manuals Search And Download.
To ensure long product life, avoid installing this unit in the following locations:
•
•
•
•
•
Locations exposed to direct sunlight.
Humid or poorly ventilated areas.
Areas of extreme temperatures.
Areas with vibration.
Dusty or smoky areas.
•
Areas exposed to grease fumes, steam or heat (such as a kitchen).
Maintenance
Use a dry polishing cloth to wipe off dust and dirt. If the surface is extremely dirty, wipe with a soft cloth dipped in neutral
cleanser diluted five to six times with water and wrung out well. Do not use volatile chemicals such as paint thinner or
benzenes, as these may corrode the surface of the panels. Do not use sprays such as insecticides around the TAD-M600. If
you plan on using a chemical cleaning cloth, read the precautionary statements of the chemical cleaning cloth before using.
TAD-M600
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Published by Pioneer Corporation.
Copyright © 2009 TECHNICAL AUDIO DEVICES LABORATORIES, INC.
All rights reserved.
TECHNICAL AUDIO DEVICES LABORATORIES, INC.
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
Printed in Japan
<SWTRF> <09G00001>
<CRB3085-A>
Download from Www.Somanuals.com. All Manuals Search And Download.
|