MAN-DEH-3900MP-GB.fm Page 1 Monday, January 15, 2007 3:45 PM
CD RDS Receiver
Operation Manual
DEH-3900MP
to register your product
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 3 Monday, January 15, 2007 3:45 PM
Installation
1. Insert the mounting sleeve into the dashboard.
DIN Rear-mount
• When installing in a shallow space, use a supplied mounting sleeve. If there is
enough space behind the unit, use factory supplied mounting sleeve.
1. Extend top and bottom of the trim ring outwards to remove the trim ring. (When
reattaching the trim ring, point the side with a groove downwards and attach it.)
2. Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°)
into place.
• It becomes easy to remove the trim ring if the front panel is released.
3. Install the unit as illustrated.
Removing the Unit
Trim ring
1. Extend top and bottom of the trim ring outwards to remove the trim ring. (When
reattaching the trim ring, point the side with a groove downwards and attach it.)
• It becomes easy to remove the trim ring if the front panel is released.
2. Determine the appropriate position where the holes on the bracket and the side
of the unit match.
Trim ring
2. Insert the supplied extraction keys into both sides of the unit until they click into
place.
3. Pull the unit out of the dashboard.
3. Tighten two screws on each side.
• Use either truss screws (5 mm x 8 mm) or flush surface screws (5 mm x 9 mm),
depending on the shape of screw holes in the bracket.
Screw
Dashboard or Console
Factory radio mounting bracket
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 4 Monday, January 15, 2007 3:45 PM
4
Installation
Connecting the Units
Notes
•
Fastening the front panel
When this unit is installed in a vehicle without ACC (accessory) position on the ignition
switch, red cable must be wired to the terminal that can detect the operation of the ignition
key. Otherwise, battery drain may result.
If you do not plan to detach the front panel, the front panel can be fastened with
supplied screw.
Screw
ACC position
No ACC position
•
•
Use this unit in other than the following conditions could result in fire or malfunction.
– Vehicles with a 12-volt battery and negative grounding.
– Speakers with 50 W (output value) and 4 ohm to 8 ohm (impedance value).
To prevent short-circuit, overheating or malfunction, be sure to follow the directions below.
– Disconnect the negative terminal of the battery before installation.
– Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap
adhesive tape around them where they lie against metal parts.
– Place all cables away from moving parts, such as gear shift and seat rails.
– Place all cables away from hot places, such as near the heater outlet.
– Do not pass the yellow cable through a hole into the engine compartment to connect to a
battery.
– Cover any disconnected cable connectors with insulating tape.
– Do not shorten any cables.
– Never cut the insulation of the power cable of this unit in order to share the power to other
equipment. Current capacity of the cable is limited.
– Use a fuse of the rating prescribed.
– Never wire the speaker negative cable directly to ground.
– Never band together multiple speaker’s negative cables.
•
Control signal is output through blue/white cable when this unit is powered on. Connect it to
an external power amp’s system remote control or the vehicle’s auto-antenna relay control
terminal (max. 300 mA, 12 V DC). If the vehicle is equipped with a glass antenna, connect
it to the antenna booster power supply terminal.
•
•
Never connect blue/white cable to external power amp’s power terminal. Also, never
connect it to the power terminal of the auto antenna. Otherwise, battery drain or malfunction
may result.
Black cable is ground. This cable and other product’s ground cable (especially, high-current
products such as power amp) must be wired separately. Otherwise, fire or malfunction may
result if they are accidentally detached.
•
Cord function may differ according to the product, even if cord color is the same. When
connecting this system, be sure to check all manuals and connect cords correctly.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 5 Monday, January 15, 2007 3:45 PM
Connecting the Units
Connect with RCA cables
(sold separately)
Note
Depending on the kind of vehicle, the
function of 3* and 5* may be different. In this
case, be sure to connect 2* to 5* and 4* to 3*.
Power amp (sold
separately)
This product
Wired remote input
Hard-wired remote control adaptor can
be connected (sold separately).
Rear output
Antenna jack
Fuse
(10 A)
Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
Connect leads of the same
color to each other.
Cap (1*)
Do not remove cap if this
Blue/white (7*)
Connect to auto-antenna relay control
System remote control
terminal is not in use.
terminal (max. 300 mA 12 V DC).
Blue/white (6*)
Yellow (3*)
Back-up (or accessory)
Yellow (2*)
Connect to the constant 12 V supply
terminal.
The pin position of the ISO connector will
differ depends on the type of vehicle.
Connect 6* and 7* when Pin 5 is an
antenna control type. In another type of
vehicle, never connect 6* and 7*.
Red (4*)
Connect to terminal controlled by
ignition swich (12 V DC).
Red (5*)
Accessory (or back-
up)
Left
Right
Rear Speaker
Rear Speaker
Black (chassis ground)
Connect to a clean, paint-free metal location.
Perform these connections when using
the optional amplifier.
Speaker leads
White:
White/black:
Gray:
Gray/black:
Green:
Green/black:
Violet:
Violet/black:
Front left +
ISO connector
Yellow/black
If you use an equipment with Mute
function, wire this lead to the Audio
Mute lead on that equipment. If not,
keep the Audio Mute lead free of any
connections.
Front left -
Front right +
Front right -
Rear left +
Rear left -
Rear right +
Rear right -
Note
In some vehicles, the ISO connector may
be divided into two. In this case, be sure
to connect to both connectors.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 6 Monday, January 15, 2007 3:45 PM
6
Before You Start
About WMA
If you want to dispose this product, do not mix it with general household
waste. There is a separate collection system for used electronic
products in accordance with legislation that requires proper treatment,
recovery and recycling.
The Windows Media™ logo printed on the box indicates
that this unit can play back WMA data.
WMA is short for Windows Media Audio and refers to an
audio compression technology that is developed by
Microsoft Corporation. WMA data can be encoded by
using Windows Media Player version 7 or later.
Private households in the 25 member states of the EU, in Switzerland and Norway
may return their used electronic products free of charge to designated collection
facilities or to a retailer (if you purchase a similar new one).
Windows Media and the Windows logo are trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries.
For countries not mentioned above, please contact your local authorities for the correct
method of disposal.
Note
By doing so you will ensure that your disposed product undergoes the necessary
treatment, recovery and recycling and thus prevent potential negative effects on the
environment and human health.
•
This unit may not operate correctly depending on the application used to encode WMA files.
About MP3
About this unit
Supply of this product only conveys a license for private, non-commercial use and
does not convey a license nor imply any right to use this product in any commercial
(i.e. revenue-generating) real time broadcasting (terrestrial, satellite, cable and/or any
other media), broadcasting/streaming via internet, intranets and/or other networks or
in other electronic content distribution systems, such as pay-audio or audio-on-
demand applications. An independent license for such use is required. For details,
The tuner frequencies on this unit are allocated for use in Western Europe, Asia, the
Middle East, Africa and Oceania. Use in other areas may result in poor reception. The
RDS (radio data system) function operates only in areas with FM stations broadcasting
RDS signals.
! CAUTION
• Do not allow this unit to come into contact with liquids. Electrical shock could result.
Also, this unit damage, smoke, and overheat could result from contact with liquids.
Visit our website
• “CLASS 1 LASER PRODUCT”
Visit us at the following site:
This product contains a laser diode of higher class than 1. To ensure continued
safety, do not remove any covers or attempt to gain access to the inside of the
product. Refer all servicing to qualified personnel.
• The Pioneer CarStereo-Pass is for use only in Germany.
• Register your product. We will keep the details of your purchase on file to help you
refer to this information in the event of an insurance claim such as loss or theft.
• Keep this manual handy as a reference for operating procedures and precautions.
• Always keep the volume low enough so that you can hear sounds from outside the
vehicle.
• We offer the latest information about Pioneer Corporation on our website.
• Protect this unit from moisture.
• If the battery is disconnected or discharged, the preset memory will be erased and
must be reprogrammed.
• Should this product fail to operate properly, contact your dealer or nearest
authorized Pioneer Service Station.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 7 Monday, January 15, 2007 3:45 PM
Before You Start
Operating this unit
What’s What
Head unit
Protecting your unit from theft
The front panel can be detached to deter theft.
Important
• Handle gently when removing or attaching the front panel.
• Avoid subjecting the front panel to excessive shocks.
• Keep the front panel out of direct sunlight and high temperatures.
Removing the front panel
1. Press DETACH to release the front panel.
2. Grab the front panel and remove.
ቢ AUDIO button
ቩ DETACH button
Press to select various sound quality
controls.
Press to remove the front panel from
the head unit.
ባ EQ button
ቪ DISPLAY button
3. Put the front panel into provided protective case for safe keeping.
Press to select various equalizer
curves.
Press to select different displays.
ቫ LOUD button
Attaching the front panel
ቤ SOURCE button, VOLUME
Press to turn loudness on or off.
ቭ 1 to 6 buttons
1. Slide the front panel to the left until it clicks.
This unit is turned on by selecting a
source. Press to cycle through all the
available sources.
Press and hold to recall the initial
setting menu when the sources are
off.
Front panel and the head unit are jointed on the left side. Make sure that the front panel
has been jointed to the head unit.
Press for preset tuning.
ቮ 8/2/4/6 buttons
2. Press the right side of the front panel until it is firmly seated.
Press to perform manual seek tuning,
fast forward, reverse and track search
controls. Also used for controlling
functions.
• If you can’t attach the front panel to the head unit successfully, try again. Front panel
may be damaged if you attach the front panel forcedly.
Rotate it to increase or decrease the
volume.
ብ Disc loading slot
Insert a disc to play.
ቦ EJECT button
ቯ BAND button
Press to select among MW/LW and
two FM bands and cancel the control
mode of functions.
Press and hold to turn regional
function on or off.
Press to eject a CD from your built-in
CD player.
ቧ TA button
ተ FUNCTION button
Press to turn TA function on or off.
Press and hold to turn AF function
on or off.
Press to recall the function menu
when operating a source.
ቨ AUX input jack (3.5 mm stereo jack)
Use to connect an auxiliary
equipment.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 8 Monday, January 15, 2007 3:45 PM
8
Operating this unit
Optional remote control
LCD display
The remote control CD-SR100 is sold separately.
Operation is the same as when using the buttons on the head unit. See the explanation
of the head unit about the operation of each button with the exception of ATT, which
is explained below.
ᕡ Main display section
Shows the various information such as band, play time, and other setting.
• Tuner
Band and frequency are displayed.
• RDS
Program service name, PTY information or frequency is displayed.
ቱ ATT button
Press to quickly lower the volume level, by about 90%. Press once more to return
to the original volume level.
• Built-in CD Player (Audio CD)
Erapsed play time is displayed.
ቲ SOURCE button
• Built-in CD Player (WMA/MP3/WAV disc)
Folder number and erapsed play time are displayed.
Press to cycle through all the available sources. Press and hold to turn the source
off.
• Audio and initial setup
Function names and setup status are displayed.
ታ VOLUME button
Press to increase or decrease the volume.
ᕢ Preset number/track number indicator
ᕦ MP3/WMA indicator
Shows the track number or preset
number.
Shows the type of the currently
playing disc.
• If a track number 100 or more is
selected, 6 on the left of the track
number indicator will light.
ᕧ RPT indicator
Shows when repeat play is turned
on.
ᕣ AF indicator
ᕨ LOUD indicator
Shows when AF (alternative
frequencies search) function is on.
Appears in the display when
loudness is turned on.
ᕤ TP indicator
ᕩ Stereo (%) indicator
Shows when a TP station is tuned in.
ᕥ TA indicator
Shows when the selected frequency
is being broadcast in stereo.
Shows when TA (traffic
announcement standby) function is
on.
µ LOC indicator
Shows when local seek tuning is on.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 9 Monday, January 15, 2007 3:45 PM
Operating this unit
Basic Operations
Tuner
Turning the unit on and selecting a source
Listening to the radio
You can select a source you want to listen to. To switch to the built-in CD player, load
a disc in the unit (refer to page 12).
1. Press SOURCE to select the tuner.
2. Press BAND to select a band.
* Press SOURCE to select a source.
Press SOURCE repeatedly to switch between the following sources:
Tuner – Built-in CD player – AUX
Press BAND until the desired band (F1, F2 for FM or MW/LW) is displayed.
3. To perform manual tuning, briefly press 4 or 6.
4. To perform seek tuning, press and hold 4 or 6 for about one second and
release.
Notes
•
In the following cases, the sound source will not change:
– When there is no disc in the unit.
The tuner will scan the frequencies until a broadcast strong enough for good reception
is found.
– When the AUX (auxiliary input) is set to off (refer to page 15).
AUX is set to on by default. Turn off the AUX when not in use (refer to “Switching the auxiliary
setting” on page 15).
When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control
terminal, the vehicle’s antenna extends when this unit’s source is turned on. To retract the
antenna, turn the source off.
•
•
• You can cancel seek tuning by briefly pressing 4 or 6.
• If you press and hold 4 or 6 you can skip stations. Seek tuning starts as soon as
you release the button.
Storing and recalling broadcast frequencies
Adjusting the volume
* When you find a frequency that you want to store in memory, press one of preset
tuning buttons 1 to 6 and hold until the preset number stops flashing.
* Use VOLUME to adjust the sound level.
Memorized radio station frequency can be recalled by pressing the preset tuning
button.
Turning the unit off
* Press SOURCE and hold until the unit turns off.
• Up to 12 FM stations, 6 for each of the two FM bands, and 6 MW/LW stations can
be stored in memory.
• Press 8 or 2 to recall radio station frequencies.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 10 Monday, January 15, 2007 3:45 PM
10
Operating this unit
Tuning in strong signals
Switching the RDS display
Local seek tuning lets you tune in only those radio stations with sufficiently strong
signals for good reception.
* Press DISPLAY.
Press DISPLAY repeatedly to switch between the following settings:
Program service name – PTY information – Frequency
PTY (program type ID code) information is listed on page 11.
• PTY information and the frequency appear on the display for eight seconds.
1. Press FUNCTION to select LOCAL.
2. Press 8 or 2 to turn local seek tuning on or off.
3. Press 4 or 6 to set the sensitivity.
FM: LOCAL 1 – LOCAL 2 – LOCAL 3 – LOCAL 4
MW/LW: LOCAL 1 – LOCAL 2
Receiving PTY alarm broadcasts
When the emergency PTY code broadcasts, the unit receives it automatically (ALARM
appears). When the broadcasting ends, the system returns to the previous source.
The LOCAL 4 setting allows reception of only the strongest stations, while lower
settings let you receive progressively weaker stations.
• An emergency announcement can be canceled by pressing TA.
Storing the strongest broadcast frequencies
Selecting alternative frequencies
BSM (best stations memory) lets you automatically store the six strongest broadcast
frequencies under preset tuning buttons 1 to 6. Once stored you can tune in to those
frequencies with the touch of button.
When the tuner can’t get good reception, the unit automatically search for a different
station in a same network.
* Press and hold TA repeatedly to turn AF (alternative frequency search) on or off.
• Storing broadcast frequencies with BSM may replace broadcast frequencies you
have saved using buttons 1 to 6.
Notes
•
You can also turn the AF function on or off in the menu that appears with the pressing of
FUNCTION.
1. Press FUNCTION to select BSM.
•
•
Only RDS stations are tuned in during seek tuning or BSM when AF is on.
When you recall a preset station, the tuner may update the preset station with a new
frequency from the station’s AF list. (This is only available when using presets on the F1 or
F2 bands.) No preset number appears on the display if the RDS data for the station received
differs from that for the originally stored station.
2. Press 8 to turn BSM on.
Six strongest broadcast frequencies will be stored in the order of their signal strength.
• To cancel the storage process, press 2.
•
•
Sound may be temporarily interrupted by another program during an AF frequency search.
AF can be turned on or off independently for each FM band.
RDS
Using PI Seek
Introduction of RDS operation
If the tuner can’t find a suitable station, or reception status becomes bad, the unit will
automatically search for a different station with a same programming. During the
search, PI SEEK is displayed and the output is muted.
RDS (radio data system) contains inaudible informations that helps searching of the
radio stations.
• RDS service may not be provided by all stations.
Using Auto PI Seek for preset stations
• RDS functions such as AF and TA are only active when your radio is tuned to an
RDS station.
When preset stations cannot be recalled, as when travelling long distances, the unit
can be set to perform PI Seek during preset recall.
• The default setting for Auto PI Seek is off. See “Switching Auto PI Seek” on page 15.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 11 Monday, January 15, 2007 3:45 PM
Operating this unit
Limiting stations to regional programming
PTY list
Specific
When AF is used, the regional function limits the selection of stations broadcasting
regional programs.
Type of program
News
NEWS
1. Press FUNCTION to select REG.
2. Press 8 or 2 to turn the regional function on or off.
Notes
AFFAIRS
INFO
Current affairs
General information and advice
Sports
SPORT
WEATHER
FINANCE
POP MUS
ROCK MUS
EASY MUS
OTH MUS
JAZZ
Weather reports/meteorological information
Stock market reports, commerce, trading, etc.
Popular music
•
•
•
Regional programming and regional networks are organized differently depending on the
country (i.e., they may change according to the hour, state or broadcast area).
The preset number may disappear from the display if the tuner tunes in a regional station
which differs from the originally set station.
Contemporary modern music
Easy listening music
Non-categorized music
Jazz
The regional function can be turned on or off independently for each FM band.
Receiving traffic announcements
TA (traffic announcement standby) lets you receive traffic announcements
automatically, no matter what source you are listening to. TA can be activated for both
a TP station (a station that broadcasts traffic information) or an enhanced other
network’s TP station (a station carrying information which cross-references TP
stations).
COUNTRY
NAT MUS
OLDIES
Country music
National music
Oldies, golden oldies
Folk music
FOLK MUS
L.CLASS
CLASSIC
EDUCATE
DRAMA
Light classical music
Classical music
1. Tune in a TP or enhanced other network’s TP station.
TP indicator will light.
Educational programs
Radio plays and serials
National or regional culture
Nature, science and technology
Light entertainment
Children’s
2. Press TA to turn traffic announcement standby on.
CULTURE
SCIENCE
VARIED
• To turn traffic announcements standby off, press TA again.
3. Use VOLUME to adjust the TA volume when a traffic announcement begins.
The newly set volume is stored in memory and recalled for subsequent traffic
announcements.
CHILDREN
SOCIAL
Social affairs
4. Press TA while a traffic announcement is being received to cancel the
announcement.
RELIGION
PHONE IN
TOURING
LEISURE
DOCUMENT
Religious affairs or services
Phone in
The tuner returns to the original source but remains in the standby mode until TA is
pressed again.
Travel programs; not for traffic announcements
Hobbies and recreational activities
Documentaries
• You can also cancel the announcement by pressing SOURCE, BAND, 8, 2, 4 or
6 while a traffic announcement is being received.
Notes
•
You can also turn the TA function on or off in the menu that appears with the pressing of
FUNCTION.
•
•
The system switches back to the original source following traffic announcement reception.
Only TP and enhanced other network’s TP stations are tuned in during seek tuning or BSM
when TA is on.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 12 Monday, January 15, 2007 3:45 PM
12
Operating this unit
Built-in Player
Playing a disc
Repeating play
Repeat play plays the same track/folder within the selected repeat play range.
1. Press FUNCTION to select RPT.
1. Insert a CD (CD-ROM) into the disc loading slot.
Playback will automatically start.
2. Press 4 or 6 to select the repeat range.
DSC – Repeat all tracks
• Be sure to turn up the label side of a disc.
TRK – Repeat just the current track
FLD – Repeat the current folder
• After a CD (CD-ROM) has been inserted, press SOURCE to select the built-in CD
player.
• If you select another folder during repeat play, the repeat play range changes to disc
• You can eject a CD (CD-ROM) by pressing EJECT.
repeat.
• When playing CD, performing track search or fast forward/reverse cancels the
repeat play automatically.
2. Press 8 or 2 to select a folder when playing a WMA/MP3/WAV disc.
• You cannot select a folder that does not have a WMA/MP3/WAV file recorded in it.
• When playing WMA/MP3/WAV disc, performing track search or fast forward/reverse
during TRK (track repeat) changes the repeat play range to folder repeat.
• To return to folder 01 (ROOT), press and hold BAND. However, if folder 01 (ROOT)
contains no files, playback commences with folder 02.
• When FLD (folder repeat) is selected, it is not possible to play back a subfolder of
that folder.
3. To perform fast forward or reverse, press and hold 4 or 6.
If you select ROUGH, pressing and holding 4 or 6 enables you to search every 10
tracks in the current disc (folder). (Refer to “Searching every 10 tracks in the current
disc or folder” on page 13.)
• To return to the normal display, press BAND.
Playing tracks in random order
4. To skip back or forward to another track, press 4 or 6.
Random play plays tracks in a random order within the selected repeat range.
Notes
1. Select the repeat range.
•
•
•
Read the precautions with discs and player on page 17.
Refer to “Repeating play” on this page.
If an error message such as ERROR-11 is displayed, refer to “Error messages” on page 16.
There is sometimes a delay between starting up disc playback and the sound being issued.
When being read, FRMTREAD is displayed.
2. Press FUNCTION to select RDM.
•
•
•
•
•
When playing CD-EXTRA or MIXED-MODE CDs, WMA/MP3/WAV and CD-DA can be
swithced by pressing BAND.
If you have switched between WMA/MP3/WAV files and audio CD-DA, playback starts at
the first track on the disc.
The built-in CD player can play back a WMA/MP3/WAV file recorded on CD-ROM. (Refer to
page 17 for files that can be played back.)
When playing back VBR (variable bit rate) recorded files, erapsed play time may not be
displayed correctly.
When playing WMA/MP3/WAV disc, there is no sound on fast forward or reverse.
3. Press 8 or 2 to turn random play on or off.
When random play is on, RDM appears in the display.
If you turn random play on during folder repeat, FRDM appears in the display.
• To return to the normal display, press BAND.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 13 Monday, January 15, 2007 3:45 PM
Operating this unit
Scanning tracks or folders
Searching every 10 tracks in the current disc or folder
Scan play searches the song within the selected repeat range.
You can switch the search method between fast forward/reverse and searching every
10 tracks. Selecting ROUGH enables you to search every 10 tracks.
1. Select the repeat range.
1. Press FUNCTION to select FF/REV.
Refer to “Repeating play” on page 12.
• If the search method ROUGH has been previously selected, ROUGH will be
displayed.
2. Press FUNCTION to select SCAN.
3. Press 8 to turn scan play on.
2. Press 6 to select ROUGH.
SCAN appears in the display. The first 10 seconds of each track is played.
• If you turn scan play on during FLD, FSCN appears in the display.
• FF/REV – Fast forward and reverse
• ROUGH – Searching every 10 tracks
• To select FF/REV, press 4.
4. When you find the desired track press 2 to turn scan play off.
• If the display has automatically returned to the playback display, select SCAN again
by pressing FUNCTION.
3. Press BAND to return to the playback display.
4. Press and hold 4 or 6 to search every 10 tracks on a disc (folder).
• After scanning of a disc (folder) is finished, normal playback of the tracks will begin
again.
• If the rest of track number is less than 10, press and hold 4 or 6 recalls the first (last)
one.
Pausing disc playback
Displaying text information on disc
Pause lets you temporarily stop playback of the disc.
1. Press FUNCTION to select PAUSE.
* Press DISPLAY.
Press DISPLAY repeatedly to switch between the following settings:
2. Press 8 or 2 to turn pause on or off.
For CD TEXT discs
• To return to the normal display, press BAND.
Play time – DISC TTL (disc title) – DISC ART (disc artist name) – TRK TTL (track title)
– TRK ART (track artist name)
Using compression and BMX
For WMA/MP3 discs
Play time – FOLDER (folder name) – FILE (file name) – TRK TTL (track title) –
ARTIST (artist name) – ALBUM (album title) – COMMENT (comment) – Bit rate
Using the COMP (compression) and BMX functions let you adjust the sound playback
quality of this unit.
1. Press FUNCTION to select COMP OFF.
For WAV discs
2. Press 8 or 2 to select your favorite setting.
Play time – FOLDER (folder name) – FILE (file name) – Sampling frequency
COMP OFF – COMP 1 – COMP 2 – COMP OFF – BMX 1 – BMX 2
• To return to the normal display, press BAND.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 14 Monday, January 15, 2007 3:45 PM
14
Operating this unit
Notes
Adjusting equalizer curves
•
•
•
You can scroll to the left of the title by pressing and holding DISPLAY.
Audio CD that contain certain information such as text and/or number are CD TEXT.
If specific information has not been recorded on a disc, NO XXXX will be displayed (e.g., NO
T-TTL).
You can adjust the currently selected equalizer curve setting as desired. Adjusted
equalizer curve settings are memorized in CUSTOM.
Adjusting bass/mid/treble
•
•
When playing back VBR-recorded WMA files, the average bit rate value is displayed.
When playing back VBR (variable bit rate)-recorded MP3 files, VBR is displayed instead of
bit rate value.
You can adjust the bass/mid/treble level.
1. Press AUDIO to select BASS/MID/TREBLE.
•
Depending on the version of iTunes® used to write MP3 files onto a disc, comment
information may not be correctly displayed.
2. Press 8 or 2 to adjust the level.
– iTunes is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
The sampling frequency shown in the display may be abbreviated.
•
+6 to –6 is displayed as the level is increased or decreased.
• To return to the normal display, press BAND.
Audio Adjustments
Adjusting loudness
Using balance adjustment
Loudness compensates for deficiencies in the low- and high-sound ranges at low
volume.
Fader/balance setting creates an ideal listening environment in all occupied seats.
1. Press AUDIO to select FAD.
1. Press AUDIO to select LOUD.
2. Press 8 or 2 to turn loudness on or off.
2. Press 8 or 2 to adjust front/rear speaker balance.
FAD F15 to FAD R15 is displayed.
• You can also turn loudness on or off by pressing LOUD.
3. Press 4 or 6 to select a desired level.
LOW (low) – HI (high)
• FAD 0 is the proper setting when only two speakers are used.
3. Press 4 or 6 to adjust left/right speaker balance.
BAL L15 to BAL R15 is displayed.
• To return to the normal display, press BAND.
• To return to the normal display, press BAND.
Adjusting source levels
SLA (source level adjustment) lets you adjust the volume level of each source to
prevent radical changes in volume when switching between sources.
Using the equalizer
There are six stored equalizer settings such as DYNAMIC, VOCAL, NATURAL,
CUSTOM, FLAT and POWERFUL that can easily be recalled at any time.
• Settings are based on the FM tuner volume level, which remains unchanged.
• The MW/LW tuner volume level can also be adjusted with source level adjustments.
• CUSTOM is an adjusted equalizer curve that you create.
1. Compare the FM tuner volume level with the level of the source you wish to
adjust.
• When FLAT is selected no supplement or correction is made to the sound.
* Press EQ to select the equalizer.
Press EQ repeatedly to switch between the following equalizers:
DYNAMIC – VOCAL – NATURAL – CUSTOM – FLAT – POWERFUL
2. Press AUDIO to select SLA.
3. Press 8 or 2 to adjust the source volume.
SLA +4 to SLA –4 is displayed as the source volume is increased or decreased.
• To return to the normal display, press BAND.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 15 Monday, January 15, 2007 3:45 PM
Operating this unit
Other Functions
Switching the auxiliary setting
It is possible to use auxiliary equipment with this unit. Activate the auxiliary setting
when using auxiliary equipment connected to this unit.
Adjusting initial settings
1. Press FUNCTION to select AUX.
Using the initial settings, you can customize various system settings to achieve optimal
performance from this unit.
2. Press 8 or 2 to turn the auxiliary setting on or off.
1. Press SOURCE and hold until the unit turns off.
Multi language display setting
2. Press SOURCE and hold until function name appears in the display.
Text information such as title name, artist name or comment can be recorded on a
WMA/MP3/WAV disc.
3. Press FUNCTION to select one of the initial settings.
Press FUNCTION repeatedly to switch between the following settings:
This unit can display them even if they are embedded in either European language or
Russian language.
FM (FM tuning step) – A-PI (auto PI Seek) – AUX (auxiliary input) – TITLE (multi
language) – SAVE (power save)
• If embedded language and selected language setting are not consistent with each
other, text information may not be displayed properly.
Use the following instructions to operate each particular setting.
• To cancel initial settings, press BAND.
• Some characters may not be displayed properly.
• You can also cancel initial settings by holding down SOURCE until the unit turns off.
1. Press FUNCTION to select TITLE.
2. Press 4 or 6 to select the language.
Setting the FM tuning step
EUR (European language) – RUS (Russian language)
Normally the FM tuning step employed by seek tuning is 50 kHz. When AF or TA is on,
the tuning step automatically changes to 100 kHz. It may be preferable to set the
tuning step to 50 kHz when AF is on.
Saving the battery consumption
Switching this function on enables you to save the consumption of battery power.
• Operations other than turning on the source are not allowed when this function is on.
• The tuning step remains at 50 kHz during manual tuning.
1. Press FUNCTION to select FM.
Important
2. Press 4 or 6 to select the FM tuning step.
• If the battery in your vehicle is disconnected the Power Save mode is canceled. Turn
on Power Save again once the battery has been reconnected. If the ignition switch
in your vehicle doesn’t have an ACC (accessory) position, it is possible depending
on the connection method that when Power Save is off, the unit will draw power from
the battery.
Press 4 to select 50 (50 kHz). Press 6 to select 100 (100 kHz).
Switching Auto PI Seek
The unit can automatically search for a different station with the same programming,
even during preset recall.
1. Press FUNCTION to select SAVE.
1. Press FUNCTION to select A-PI.
2. Press 8 or 2 to turn the power save on or off.
2. Press 8 or 2 to turn the Auto PI seek on or off.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 16 Monday, January 15, 2007 3:45 PM
16
Operating this unit
Additional Information
Sound muting
Error messages
Sound from this unit is muted automatically in the following cases:
• When a call is made or received using a cellular telephone connected to this unit.
When you contact your dealer or your nearest Pioneer Service Center, be sure to
record the error message.
• When the voice guidance is output from a Pioneer navigation unit connected to this
unit.
Message
Cause
Action
The sound is turned off, MUTE is displayed and no audio adjustments, except volume
control, are possible. Operation returns to normal when the phone connection or the
voice guidance is ended.
ERROR-11, 12, 17, 30
ERROR-11, 12, 17, 30
Dirty disc
Clean disc.
Replace disc.
Scratched disc
Electrical or mechanical
ERROR-10, 11, 12, 15,
17, 30, A0
Turn the ignition ON and OFF, or
switch to a different source, then
back to the CD player.
ERROR-15
The inserted disc does not
contain any data
Replace disc.
Replace disc.
Replace disc.
ERROR-22, 23
NO AUDIO
The CD format cannot be
played back
The inserted disc does not
contain any files that can be
played back
PROTECT
SKIPPED
All the files on the inserted disc Replace disc.
are secured by DRM
The inserted disc contains WMA Replace disc.
files that are protected by DRM
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 17 Monday, January 15, 2007 3:45 PM
Additional Information
Handling guideline of discs and player
Dual Discs
• Use only discs featuring either of following two logos.
• Dual Discs are two-sided discs that have a recordable CD for audio on one side and
a recordable DVD for video on the other.
• Since the CD side of Dual Discs is not physically compatible with the general CD
standard, it may not be possible to play the CD side with this unit.
• Frequent loading and ejecting of a Dual Disc may result in scratches on the disc.
Serious scratches can lead to playback problems on this unit. In some cases, a Dual
Disc may become stuck in the disc loading slot and will not eject. To prevent this, we
recommend you refrain from using Dual Disc with this unit.
• Use only conventional, fully circular discs. Do not use shaped discs.
• Please refer to the information from the disc manufacturer for more detailed
information about Dual Discs.
WMA, MP3 and WAV files
• Use 12-cm or 8-cm CD. Do not use an adapter when playing 8-cm CDs.
• Depending on the version of Windows Media Player used to encode WMA files,
• Do not insert anything other than a CD into the CD loading slot.
album names and other text information may not be correctly displayed.
• Do not use cracked, chipped, warped, or otherwise damaged discs as they may
• There may be a slight delay when starting playback of WMA files encoded with
damage the player.
image data.
• Unfinalized CD-R/CD-RW disc playback is not possible.
• ISO 9660 Level 1 and 2 compliant. Romeo and Joliet file systems are both
compatible with this player.
• Do not touch the recorded surface of the discs.
• Multi-session playback is possible.
• Store discs in their cases when not in use.
• WMA/MP3/WAV files are not compatible with packet write data transfer.
• Avoid leaving discs in excessively hot environments including under direct sunlight.
• Do not attach labels, write on or apply chemicals to the surface of the discs.
• To clean a CD, wipe the disc with a soft cloth outward from the center.
• Only 64 characters from the beginning can be displayed as a file name (including
the extension such as .wma, .mp3 or .wav) or a folder name.
• Folder selection sequence or other operation may be altered depending on the
encoding or writing software.
• Condensation may temporarily impair the player’s performance. Leave it to adjust to
the warmer temperature for about one hour. Also, wipe any dump discs with a soft
cloth.
• Regardless of the length of blank section between the songs of original recording,
WMA/MP3/WAV discs will play with a short pause between songs.
• Playback of discs may not be possible because of disc characteristics, disc format,
recorded application, playback environment, storage conditions and so on.
• File extensions such as .wma, .mp3 or .wav must be used properly.
• Text information may not be correctly displayed depending on the recorded
environment.
• Road shocks may interrupt disc playback.
• Read the precautions with discs before using them.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 18 Monday, January 15, 2007 3:45 PM
18
Additional Information
Example of a hierarchy
Russian character chart
: Folder
: File
Display
Character
Display
Character
• This unit assigns folder numbers. The user
cannot assign folder numbers.
А
Б
• Folder hierarchy is allowed up to eight tiers.
However, practical hierarchy of folder is less
than two tiers.
В
Д
Г
Е, Ё
З
• Up to 99 folders on a disc can be played back.
Ж
И, Й
Л
Compressed audio compatibility
WMA
Level 1 Level 2 Level 3 Level 4
К
• Compatible format: WMA encoded by
Windows Media Player Ver. 7, 7.1, 8, 9 or 10
М
• Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to 384 kbps (VBR)
• Sampling frequency: 32 kHz to 48 kHz
Н
О
• Windows Media Audio 9 Professional, Lossless, Voice: No
MP3
П
Р
• Bit rate: 8 kbps to 320 kbps
• Sampling frequency: 16 kHz to 48 kHz (32 kHz, 44.1 kHz, 48 kHz for emphasis)
С
Т
• Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3 tag Version 2.x is given
priority than Version 1.x.)
• M3u playlist: No
У
Ф
• MP3i (MP3 interactive), mp3 PRO: No
WAV
Х
Ц
• Compatible format: Linear PCM (LPCM), MS ADPCM
• Quantization bits: 8 and 16 (LPCM), 4 (MS ADPCM)
Ч
Ш, Щ
Ы
• Sampling frequency: 16 kHz to 48 kHz (LPCM), 22.05 kHz to 44.1 kHz (MS ADPCM)
Ъ
Ь
Э
Ю
Я
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN-DEH-3900MP-GB.fm Page 19 Monday, January 15, 2007 3:45 PM
Additional Information
Specifications
General
CD player
Power source .............................................. 14.4 V DC System ............................. Compact disc audio system
(10.8 V to 15.1 V allowable) Usable discs .......................................... Compact disc
Grounding system .................................. Negative type Signal format:
Max. current consumption ................................ 10.0 A
Dimensions (W x H x D):
Sampling frequency ................................ 44.1 kHz
Number of quantization bits ................... 16; linear
Frequency characteristics ............... 5 Hz to 20 000 Hz
(±1 dB)
DIN
Chassis .................................. 178 x 50 x 162 mm
Nose ........................................ 188 x 58 x 14 mm Signal-to-noise ratio ............................... 94 dB (1 kHz)
D
(IEC-A network)
Chassis .................................. 178 x 50 x 162 mm Dynamic range ....................................... 92 dB (1 kHz)
Nose ........................................ 170 x 47 x 14 mm Number of channels ..................................... 2 (stereo)
Weight ................................................................ 1.3 kg WMA decoding format .................. Ver. 7, 7.1, 8, 9, 10
(2ch audio)
(Windows Media Player)
MP3 decoding format ....... MPEG-1 & 2 Audio Layer 3
WAV signal format ............ Linear PCM & MS ADPCM
Audio
Continuous power output .............................. 22 W x 4
(50 Hz to 15 000 Hz, 5% THD,
4 $ load, both channels driven)
Maximum power output ................................ 50 W x 4
Load impedance ................. 4 $ (4 $ to 8 $ allowable) Frequency range .................... 87.5 MHz to 108.0 MHz
Preout max output level/
FM tuner
Usable sensitivity .......................... 8 dBf (0.7 µV/75 $,
mono, S/N: 30 dB)
Signal-to-noise ratio ................. 75 dB (IEC-A network)
Distortion .................... 0.3 % (at 65 dBf, 1 kHz, stereo)
0.1 % (at 65 dBf, 1 kHz, mono)
output impedance ................................ 2.2 V/1 k$
Bass/Mid/Treble:
Bass
Frequency ................................................ 100 Hz
Gain ........................................................... ±13dB Frequency response ........ 30 Hz to 15 000 Hz (±3 dB)
Mid
Stereo separation ................. 45 dB (at 65 dBf, 1 kHz)
Frequency ................................................... 1 kHz
Gain .......................................................... ±12 dB
Treble
MW tuner
Frequency range ........... 531 kHz to 1 602 kHz (9 kHz)
Usable sensitivity ........................... 18 µV (S/N: 20 dB)
Signal-to-noise ratio ................. 65 dB (IEC-A network)
Frequency ................................................. 10 kHz
Gain .......................................................... ±12 dB
Loudness contour:
Low .................... +7 dB (100 Hz), +4 dB (10 kHz)
High .............. +10 dB (100 Hz), +6.5 dB (10 kHz) LW tuner
(volume: –30 dB)
Frequency range .......................... 153 kHz to 281 kHz
Usable sensitivity ........................... 30 µV (S/N: 20 dB)
Signal-to-noise ratio ................. 65 dB (IEC-A network)
Note
•
Specifications and the design are subject to possible modifications without notice due to
improvements.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
B G - P 0 0 M 3 9 H - D E N - M A
m i u l g e B n i d e t i n r P
s e r r e v s e d . g h l r t l i A
o i n . p o r a t
o i n a . t
o i n e P e r C o r 2 0 © 0 6 b g y r h i t C o p y
C o r p o i r n e P e r
h s e i d b u y b P l
7 0 4 2 7 8 - 9 1 5 5 L - : E T
M , c e x t e p p e u l C h a d e m a s . L o C o l
o s p i 1 0 1 o 3 h 8 m a c a l i C a l A v n u e . M d v a B l
0 0 1 . 1
, D o c . i F
. V . C e . d A , S . O C X I M E E D S C I N O R T C E E R L E E N O P I
0 1 5 9 8 3 2 - - 8 7 7 1 - L : E T
d a
2 , P C a n a o i L t 3 a n R r O O , h k a m , M a r w k a r y a P t e a t s l A l 3 0 0
.
D A , I N C C F A N O A I C N S T R C O E L E R E E N O I P
0 0 6 3 8 6 - 9 5 0 3 ( ) L : E T
a i l a r t s u , A 1 9 5 3 a i r o t c
d i e , V a r i e s a d , B R y r o n d u a o
8 4 1 - B 1 7 8
. D T L . Y P A T I L A R T S U S C A I O R N T E L C E R E E O I N P
5 5 7 5 7 2 - 6 4 6 5 L - : E T
9 3 6 1 5 e 9 a p o n r g , S 0 i 1 0 4 - , # d
R a r o a a n e d x A l 2 5 3
D T . L . E T
P
N T R E I A C E A S I C N S T R C O E L E R E E N O I P
1 . 1 5 0 . 0 3 ) / 0 5 7 ( L : E T
m u i g l e e , e B s l l
M e 9 - 1 2 0 1 , B a l a g n r e e e t , b K 1 0 8 e 7 n H a v
V
P E O R N U E R E E O I N P
0 4 1 4 2 1 - 4 8 0 ( 0 L ) : E T
. A .
0 , U 1 . S 5 1 4 - 0 8 0 9 a i n f i o l r a h , C e a c g B L o n 4 0 , 1 x 5 o . B O . P
. C N I ) A S U S C ( I O R N T E L C E R E E O I N P
N A P A J 5 4 , 8 6 5 3 - 1 O Y K O T U K , -
U R G O , M E E M O H C -
1
U R G O E 1 , 4 M -
N O I
O R A T R C E O E R O I P N P
M P 4 5 3 : 0 0 , 7 2 5 1 y r a n a u , J y a d M o n 2 0 e g a P f . m - G B M P 9 0 0 H - 3 N - D M E A
Download from Www.Somanuals.com. All Manuals Search And Download.
|