Lighting Systems LSB-13
1BHFꢃꢂꢃPGꢃꢆꢃ
-ZUFTQSFBEÜꢃ-4#ꢃ3BEJBMꢃ-PVWFSꢃꢂꢌ-JHIUꢃ5ꢈꢃ1FSꢃꢍꢌ'PPUꢃ /PNJOBMꢊꢃ4FDUJPO
8-1/2" (21.60 cm)
1-3/4" (4.45 cm)
2" (5.08 cm)
3
1
4
2
3-1/2" (8.89 cm)
Half Scale
Ordering Information
Family
Lamps
Length
Shielding
Ballast
Voltage
Finish
LSB
1
D
1 = 1-Lamp T5
4 = 4-Foot
D = Radial Louver
28 = 28W T5
1 = 120 volt
AL = Aluminum
8 = 8-Foot
54 = 54W T5
2 = 277 volt
WH = White
5E = 54W T5 Emergency Pack
2E = 28W T5 Emergency Pack
5D = 54W T5 Dimming
Complete ordering instructions below.
Features
Ordering Instructions
1. Housing: Extruded aluminum. Die-cast end cap mechanically attached with
no exposed fasteners or hardware.
Individual Fixtures:
1. Order number of MODULES required.
2. Lamping: One T5, 28 or 54 watt (as specified) fluorescent lamp per 4-foot
nominal section. Provided by others.
3. Reflector: Precision die-formed semi-specular aluminum.
4. Radial Louver: Precision die-formed aluminum straight blade louver, blades
are 5/8” (1.59cm) high and 5/8” (1.59cm) O.C.
2. Order one POWER FEED END SET per MODULE.
Continuous Rows:
1. Determine run length.
2. Order the appropriate number of MODULES for the complete
run.
3. Order one POWER FEED END SET per run.
4. Order one CABLE ASSEMBLY per MODULE minus one
per run.
5. For runs that exceed amperage limits, order the appropriate
number of CABLE/CORD ASSEMBLIES.
Electrical
Ballast is <10% THD, .98 ballast factor, pre-heat start. 18 gauge wire. Color-
coded quick connectors allow ease of connection for joiner modules. Power feed
is 18 gauge white SJT. For special circuiting consult factory. Factory installed
ballast disconnect allows the ballast to be disconnected from and reconnected to
incoming power under load without turning the entire circuit off.
Dimming: - 120/277 VAC 1% dimming level, 4 wire feed required.
Emergency Battery Pack: - 28 watt: 520 lumens @ 90 minutes, 54 watt: 700
lumens @ 90 minutes, 4 wire feed required.
Labels
UL, cUL, and I.B.E.W.
Mountings
Cable suspension (not shown) - 4-1/2" (11.43cm) diameter canopy finished white
enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36”
(91.44cm). Dual-screw draw-tight connector to create hairline seam between joiner
modules.
Job Information
Type:
Job Name:
Cat. No.:
Finish
Powder coated baked white or aluminum finish. Custom colors available, consult
factory.
Options and Accessories
Lamp(s):
Notes:
Emergency circuiting; special circuiting; X, T & L joiner blocks - consult factory.
ꢀꢁꢂꢃ"JSQPSUꢃ3PBEꢄꢃ'BMMꢃ3JWFSꢄꢃ."ꢃꢅꢆꢇꢆꢅꢃtꢃ ꢈꢅꢉꢊꢃꢀꢇꢋꢌꢉꢂꢁꢂꢃtꢃ'BYꢃ ꢈꢅꢉꢊꢃꢀꢇꢍꢌꢍꢇꢂꢅ
We reserve the right to change details of design, materials and finish.
XXXꢎMJHIUPMJFSꢎDPNꢃ½ꢃꢆꢅꢅꢉꢃ1IJMJQTꢃ(SPVQꢃt #ꢅꢋꢅꢉ
Download from Www.Somanuals.com. All Manuals Search And Download.
|