Philips Universal Remote PL1IRR User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.  
PL1IRR Remote Control  
User’s Guide  
IMPORTANT INFORMATION  
Warnings and Notices  
When using electrical equipment, basic safety precautions should always be followed including the following:  
a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.  
b. Do not use outdoors.  
c. Do not use near gas or electric heaters.  
d. The use of accessory equipment not recommended by the manufacturer may cause an unsafe  
condition.  
e. Do not use this equipment for other than intended use.  
f. Refer service to qualified personnel.  
SAVE THESE INSTRUCTIONS.  
WARNING: You must have access to a main circuit breaker or other power disconnect device  
before installing any wiring. Be sure that power is disconnected by removing fuses or turning the  
main circuit breaker off before installation. Installing the device with power on may expose you to  
dangerous voltages and damage the device. A qualified electrician must perform this installation.  
WARNING: Refer to National Electrical Code® and local codes for proper use specifications.  
WARNING: This equipment is intended for use in accordance with the National Electric Code® and  
local regulations. It is also intended for installation in indoor applications only. Before any electrical  
work is performed, disconnect power at the circuit breaker or remove the fuse to avoid shock or  
damage to the control. It is recommended that a qualified electrician perform this installation.  
WARNING: The PL1IRR Remote Control contains a Class 2 laser. Do not look directly into laser  
beam or damage to eye may result. Handle with caution.  
LASER RADIATION  
DO NOT STARE INTO BEAM  
CLASS 2 LASER PRODUCT  
LASER DIODE  
WAVELENGTH: 630 - 680 nm  
MAX OUTPUT: <5 mW  
Philips Selecon Limited Three-Year Warranty  
Philips Selecon offers a three-year limited warranty of its products against defects in materials or workmanship  
from the date of delivery. A copy of Philips Selecon three-year limited warranty containing specific terms and  
Philips Selecon office.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
User’s Guide  
PL1IRR Remote Control  
TABLE OF CONTENTS  
2
TABLE OF CONTENTS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PL1IRR Remote Control  
User’s Guide  
PREFACE  
About this Guide  
The document provides installation and operation instructions for the following product:  
• PL1IRR Remote Control (includes two AAA batteries and user’s guide)  
Please read all instructions before using this product. Retain this manual for future reference. Additional information  
Product Description  
The PL1IRR Remote Control is used to remotely program and control presets (1 through 6 and Off) of PL1 LED  
luminaires (IR-enabled models only) over an unobstructed range of approximately 100 feet. IR-enabled PL1 LED  
Luminaires have an integrated infrared (IR) receiver that allows them to receive IR commands from the PL1IRR  
Remote Control. Using the Remote, colors (full color mixing)/presets/intensity can be programmed/selected, raised  
and lowered, and fixtures may be turned On and Off.  
Before Using the Infrared Remote  
Install two AAA batteries (included) before operation. Refer to Figure 1 for more information.  
To install two AAA batteries (included)  
in PL1IRR remote:  
Step 1. At rear of remote, remove battery  
access panel by sliding it as  
indicated.  
Step 2. Note orientation of batteries as  
indicated in battery compartment  
of remote.  
Step 3. Install batteries.  
Step 4. Reinstall battery access panel.  
Step 5. Remote is ready for use.  
PL1IRR Remote  
WARNING! PL1IRR Remote contains a  
Class 2 laser. Do not stare or look directly  
into laser beam.  
LASER RADIATION  
DO NOT STARE INTO BEAM  
_
CLASS 2 LASER PRODUCT  
LASER DIODE  
+
WAVELENGTH: 630 - 680 nm  
MAX OUTPUT: <5 mW  
+
_
Slide battery access panel away  
from remote to install batteries.  
AAA Battery (2 each -  
supplied with remote)  
Battery Compartment  
Access Panel  
Figure 1: PL1IRR Remote Battery Installation  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
User’s Guide  
PL1IRR Remote Control  
PL1IRR PROGRAMMING REMOTE OVERVIEW  
Infrared Remote Control Features  
Laser / IR Window -  
Laser and IR programming emits from  
this end.  
Program -  
Enter - After the luminaire to be  
programmed is selected (by Laser),  
press Enter to set the luminaire to  
programming mode.  
PL1IRR LED (indicator) -  
PROGRAM  
Laser (Luminaire Selector) - Press  
Laser to select individual luminaire for  
programming / adjustment.  
The LED indicator will flash each time  
a button is pressed.  
ENTER  
LASER  
EXIT  
CANCEL  
LEARN  
Intensity Raise/Lower -  
Exit - Press to exit programming mode.  
Press top button to raise intensity and  
bottom button to lower it. Tap the up  
for 2% increase or tap down for a 1%  
decrease. Press and hold (top or  
bottom button) for sequential raise/  
lower.  
INTENSITY  
COLOR  
Cancel -  
Cancels the learn features (any  
programming made will not be  
recorded) RGBW will not be changed.  
S
T
S
S
T
S
T
T
RED  
GREEN  
BLUE  
WHITE  
Learn -  
Individual LED Color Adjustment -  
After adjustments are made, the Learn  
button (in conjunction with a preset  
button) stores the new settings to a  
specific preset if desired.  
Allows the raising or lowering of  
individual LED colors. Press top  
button to change color and bottom  
button to lower it. Tap the up for 2%  
increase or tap down for a 1%  
decrease. Press and hold (top or  
bottom button) for sequential raise/  
lower.  
PRESETS  
WHITE  
WARM  
COOL  
DAY  
Preset (White Color Temperature) -  
1
4
2
5
3
6
Presets (6 Levels or Off) -  
Allows selection of Warm, Cool or Day  
color temperatures.  
Allows selection and programming of  
one of six Presets (1 through 6) or  
Preset Off.  
OFF  
PL1IRR  
Note, only intensities may be stored  
on White Color Temperature presets.  
These presets cannot be edited or  
changed  
Note, Off cannot be edited or changed.  
LASER RADIATION  
DO NOT STARE INTO BEAM  
CLASS 2 LASER PRODUCT  
WARNING! THIS DEVICE IS A CLASS 2 LASER. DO  
NOT STARE OR LOOK DIRECTLY INTO BEAM.  
LASER DIODE  
WAVELENGTH: 630 - 680 nm  
MAX OUTPUT: <5 mW  
Figure 2: PL1IRR Programming Remote  
4
PL1IRR PROGRAMMING REMOTE OVERVIEW  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
PL1IRR Remote Control  
User’s Guide  
OPERATION AND PROGRAMMING  
Using the PL1IRR Infrared Remote Control  
To select and program PL1 LED luminaire with PL1IRR remote:  
Note: The IR, on the PL1 LED luminaire, must be set to "Enabled" in order for the PL1IRR remote to communicate  
and control the fixture. Refer to PL1 LED Luminaire Installation & User’s Manual on luminaire menu settings.  
Step 1. Point PL1IRR programming remote  
Laser / IR window directly at luminaire  
PL1 LED Luminaire  
IR programming window (as shown in  
Figure 2) and hit "Enter" button. Note,  
(IR-enabled model)  
each luminaire to be programmed/  
adjusted needs to be selected and  
programmed/adjusted individually.  
Step 2. Point PL1IRR remote directly at  
luminaire IR window and hit "Laser"  
button. Luminaire to be programmed or  
adjusted is now selected.  
PL1 IR  
Port  
Note: At luminaire IR port, a Blue LED will  
illuminate when the fixture is in programming  
mode and blink Red when buttons are pressed on  
IR remote to confirm it sees the remote and is  
receiving commands.  
PROGRAM  
ENTER  
LASER  
EXIT  
CANCEL  
LEARN  
INTENSITY  
COLOR  
S
T
S
T
S
T
S
T
RED  
GREEN  
BLUE  
WHITE  
PL1IRR Remote Control  
PRESETS  
WHITE  
WARM  
COOL  
DAY  
1
4
2
5
3
6
OFF  
PL1IRR  
Step 3. Set luminaire to preset or make  
adjustments as desired.  
Step 4. To save settings, hit "Learn" button and  
then hit any Preset button (except Off -  
Off cannot be programmed). Preset is  
Figure 3: PL1 LED Luminaire Programming / Control  
now saved. To cancel programming, hit "Cancel" button.  
Step 5. After programming or adjustments are complete, hit "Exit" button. Repeat, as desired, on additional  
luminaires to be programmed/adjusted.  
Note: Refer to PL1 LED Luminaire Installation & User’s Manual for additional information. This manual is  
Troubleshooting  
Description  
Symptom  
Possible Cause/Remedy  
Luminaire not selected by laser...  
Reselect luminaire by repeating luminaire selection step.  
Not seeing IR remote control...  
Make sure batteries are good in remote. Try fresh, fully charged  
batteries.  
Make sure IR is enabled in the fixture menu.  
Insure IR remote is pointing at IR window in luminaire and that there  
is nothing in between IR remote and luminaire IR window.  
Clean luminaire IR window.  
Fixture will not respond to IR  
remote programming unit.  
IR remote programming.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pentair Landscape Lighting AmerQuartz User Manual
Pentax Camera Lens Zoom 90 WR User Manual
Philips Baby Accessories SCF276 40 User Manual
Philips Cassette Player AQ6455 00 User Manual
Philips Cell Phone E GSM 900 1800 User Manual
Philips DVD Player PDCC JS JW 0731 User Manual
Philips Network Router ST7SB User Manual
Philips TV Antenna 32PFL6606H User Manual
Poulan Cultivator 530088051 User Manual
Powermate Portable Generator PL054300017 User Manual