CONTENTS
1. CONNECTING YOUR TV-VIDEO COMBI . . . . . . . . . . . . . . 4
Connecting the cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connecting a decoder or other equipment . . . . . . . . . . . . 4
Programming a recording (without ’SHOWVIEW’) . . . . 18
Programming a recording with TELETEXT . . . . . . . . . . . 19
Automatic recording from a satellite receiver (SAT
RECORDING) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
How to check or change a TIMER . . . . . . . . . . . . . . . . . . 20
2. INSTALLING YOUR TV-VIDEO COMBI . . . . . . . . . . . . . . . . 5
Initial installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Allocating a decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 8. ADDITIONAL FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 21
Manual TV channel search . . . . . . . . . . . . . . . . . . . . . . . . . 6
Satellite receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Special installation functions . . . . . . . . . . . . . . . . . . . . . . . 7
Automatic TV channel search . . . . . . . . . . . . . . . . . . . . . . 7
Searching for new TV channels . . . . . . . . . . . . . . . . . . . . . 8
Allocating a channel number . . . . . . . . . . . . . . . . . . . . . . . 8
Delete a TV Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setting the language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting the time and date . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Changing the TV system . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Parental control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Switching the On-screen display (OSD) on or off . . . . . 22
Switching to 16:9 wide screen picture . . . . . . . . . . . . . . 22
Switching the internal speakers on or off . . . . . . . . . . . . 23
Switching the remote control command . . . . . . . . . . . . . 23
Continuous playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Sound playback without picture . . . . . . . . . . . . . . . . . . . . 24
Switch off function (SLEEP TIMER) . . . . . . . . . . . . . . . . . 25
Switch on function (WAKE-UP TIMER) . . . . . . . . . . . . . . 25
3. IMPORTANT NOTES FOR OPERATION . . . . . . . . . . . . . . 10
SUMMARY OF USER GUIDE . . . . . . . . . . . . . . . . . . . . . . . 10 9. Before you call an engineer . . . . . . . . . . . . . . . . . . . . . . . 26
User guide (OSD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Technical terms used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4. TV SET FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Selecting a TV programme . . . . . . . . . . . . . . . . . . . . . . . . 12
Selecting the picture setting (SMART PICTURE) . . . . . . 12
Switching Incredible Surround on or off . . . . . . . . . . . . . 12
Selecting a preset sound setting (SMART SOUND) . . . 13
Automatic volume control (AVL) . . . . . . . . . . . . . . . . . . . . 13
Sound track selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
How to read TELETEXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5. PLAYBACK FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Playing a cassette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Playing an NTSC cassette . . . . . . . . . . . . . . . . . . . . . . . . . 14
Tape position indication . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Searching for tape position with the picture (picture
search) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Still picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Slow motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Searching for tape position without the picture (wind
and rewind) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Instant View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Automatic search for a tape position (index search) . . 14
Picture interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cleaning the video heads . . . . . . . . . . . . . . . . . . . . . . . . . 15
6. MANUAL RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Recording without automatic switch-off . . . . . . . . . . . . 16
Recording with automatic switch-off (OTR
one-touch-recording) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Protecting your recordings . . . . . . . . . . . . . . . . . . . . . . . . 16
Auto-assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7. PROGRAMMED RECORDING (TIMER) . . . . . . . . . . . . . . . 17
’VPS’ (Video Programming System) and ’PDC’
(Programme Delivery Control) . . . . . . . . . . . . . . . . . . . . . 17
Programming a recording (with ’SHOWVIEW’) . . . . . . . 17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS IN BRIEF
The remote control
y
Volume off: To switch the volume on or off
z
Previous programme number: To select the previous programme number
TELETEXT e TELETEXT: To switch TELETEXT on or off
PLAY G Playback : To play a recorded cassette
Rewind : During STOP and STANDBY: rewind, during PLAYBACK: reverse scanning
STOP h Pause/Stop: To stop the tape, except while a TIMER-recording is being made
Forward wind: During STOP and STANDBY: forward wind, during PLAYBACK: forward scanning
STANDBY m Switch off : To switch off set, interrupt menu
function, interrupt a programmed recording (TIMER)
H
SURROUND Surround Sound : To switch Surround Sound on/off
SMART SMART PICTURE : To call up preset picture settings
SMART # SMART SOUND : To call up preset sound settings
AUDIO Audio : To select the required sound track
0-9 Number buttons: 0 - 9
I
INDEX E Index search: In combination with
H
/
I
: to search for previous/next recording on the
cassette
RECORD/OTR n Record: To record the programme selected
STILL R Still picture: To stop the tape and show a still picture
CLEAR Delete : To delete last entry or clear programmed
recording (TIMER)
Coloured TELETEXT buttons:To select TELETEXT page directly
n red To select page/chapter shown in red at the bottom of the screen
n green To select page/chapter shown in green at the bottom of the screen
n yellow To select page/chapter shown in yellow at the bottom of the screen
n blue To select page/chapter shown in blue at the bottom of the screen
CLEAR TELETEXT: To select TELETEXT info page 100
TIMER s TIMER: To make a manual TIMER programming or to
alter or clear a programmed TIMER
MENU Menu : To call up or end main menu
OK Store/Confirm: To store or confirm entry
D
C
Select: Cursor left
Select: Cursor right
Select: One line up
Select: One line down
A
B
qSr Volume: To regulate the volume
qP r Programme number: To select a programme number
up or down
Download from Www.Somanuals.com. All Manuals Search And Download.
Front of the set
AUDIO L/R Audio input socket left/right stereo
VIDEO Video input socket : To connect a camcorder or videogames
w
Headphones socket: To connect headphones
Back of the set
8
Power switch : To switch off the machine
Beware: If you switch off with the power switch, TIMER-recordings are not possible!
2
Aerial input socket: To connect the aerial cable
AUDIO AUDIO: To connect a HiFi-set or a ’Dolby Prologic’-decoder.
EXT. 1 Scart socket: To connect a satellite receiver, decoder, video recorder, etc.
EXT. 2 Scart socket: To connect a satellite receiver, video recorder, camera recorder etc.
m
Standby : To switch off, interrupt a function, interrupt a programmed recording (TIMER)
P r/q Programme number : To select programme number up or down
Sr/qx Volume: To regulate the volume, to switch on the automatic recording from a satellite receiver
H
I
5
Rewind : During STOP and STANDBY: rewind, during PLAYBACK: reverse scanning
Forward wind: During STOP and STANDBY: forward wind, during PLAYBACK: forward scanning
Record: To record the programme selected
G
Playback : To play a recorded cassette
?
Pause/Stop: To stop the tape, except while a TIMER-recording is being made
Download from Www.Somanuals.com. All Manuals Search And Download.
Special functions on your TV-VIDEO Combi
If a TV channel which transmits TXT/PDC is stored under programme number
’P01’, time and date will automatically be taken from the TXT/PDC information.
Crystal Clear video has become the synonym for outstanding picture quality
combining Philips’ very latest technologies: Natural Colour, Studio Tracking
System, Digital Studio Picture Control and laser-cut video heads.
Philips has developed a system which produces the best possible playback
quality. It reduces disturbance on old, worn video cassettes, and emphasises
the detail on very good quality cassettes.
This function allows you to save the playback settings that suit you best. Select
your own personal settings for the type of film you are currently watching.
This function allows you to save the sound settings that suit you best. Select
your own personal settings for the type of film you are currently watching.
When you have plugged your TV-VIDEO Combi into the mains, you will be
welcomed with an OSD picture. All you have to do is follow the instructions in
the "intelligent help line" for the next step. Enjoy the Automatic TV channel
search/save function and the automatic time adjustment.
Automatic Volume Leveller. This prevents a sudden increase of the volume, for
example, during commercials.
Incredible Surround is the newest sound-improvement system from Philips. This
feature gives the acoustic impression of a very wide stereo effect even if the
speakers are located relatively close together.
Simple programming system for TV-VIDEO Combis. Makes programming as easy
as making a telephone call. Simply enter the programme code which you will
find in your listings magazine.
The precision tape drive from Philips with a rewind time of 100 seconds (E180)
and automatic tape length recognition.
By using the information stored in the Teletext pages you can programme
recordings on the TV-VIDEO Combi in just a few convenient steps.
One Touch SAT Recording is the new ease-of-use solution for TV-VIDEO Combis
to record programmes from your SAT receiver in a convenient way.
Your TV-VIDEO Combi has been equiped with two tuners. This enables you to
watch a programme while you are recording another programme.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1. CONNECTING YOUR TV-VIDEO COMBI
Connecting the cables
a Insert the aerial plug into the 2 socket.
b Insert the plug of the mains cable into the wall socket.
c If the little red light at the front panel of the set is not lit,
please switch on the set. The power switch 8 is
located on the left side panel of the set.
Connecting a decoder or other equipment
You can also connect additional equipment. For instance, a
satellite receiver, decoder or camcorder to EXT. 1 or a
satellite receiver, or camcorder to EXT. 2 .
E If you don’t connect a decoder, use the EXT. 1 socket for
connecting other equipment.
You can connect a HiFi-stereo set or a ’Dolby Prologic’
decoder to the socket AUDIO OUT L/R (audio output left/right).
DIf you want to switch off the internal speakers please
read chapter ’ADDITIONAL FUNCTIONS’, paragraph
’Switching the internal speakers on or off’.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. INSTALLING YOUR TV-VIDEO COMBI
E ’Time’, ’Year’, ’Month’, ’Date’ will appear on the
Initial installation
TV screen.
a Open up the battery compartment of your remote control
and place the batteries in it as shown in the picture.
Autostore ready
CHANNELS FOUND:
08
Time
Year
Month
Date
15:36
2000
06
08
Exit:
press MENU
b Close the battery compartment.
c Select the language for the on-screen display (OSD) with h Check if the time in line ’Time’ is correct. If required,
the B or A button.
change the time with the number buttons 0-9 on your
remote control.
d Confirm with the OK button.
i Check ’Year’, ’Month’ and ’Date’ in the same way.
e Select the country of your residence with the B or
You can switch between entry fields with B or
A
A button.
button.
If this country does not show up, select ’OTH.’.
j Confirm the new information with the OK button.
f Confirm with the OK button.
The initial installation is now complete.
g If the aerial (antenna) has been connected to the
TV-VIDEO Combi, press the OK button.
’Automatic TV channel search’ starts. This picture will
appear on the screen:
DIf you have connected a decoder, you must install it
as described in the next section.
DIf you have connected a satellite receiver, please
read the section ’satellite receiver’.
Allocating a decoder
Searching...
CHANNELS FOUND:
Some TV stations will send coded TV channels, that you can
only watch when you use a decoder. You can connect such a
decoder (descrambler) to your TV-VIDEO Combi. With the
following function, the connected decoder will automatically
be activated for the TV programme you want to watch.
//////,,,,,,,,,,,,,,,,,,,,,
a Select the TV channel for which you want to use the
decoder with the qP r button on the TV-VIDEO Combi
or the number buttons 0-9 on the remote control.
Wait until all TV channels have been found. This can take
several minutes.
b Press the MENU button on the remote control. The main
menu will appear.
c Select the line ’Installation’ with the B or
A button and confirm with the C button.
d Select the line ’Manual store’ with the B or
A button and confirm with the C button.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
e Select the line ’Decoder’ with the B or A button.
d In the line ’Channel/Frequency’, select the
display for:
’FREQU.’: frequency
MANUAL STORE
’C CH’: channel
’S CH’: special channel
Channel/Frequency
TV system
Search
FREQU.
PAL-BG
123
e If you know the frequency or channel of the desired TV
channel, you can enter the data in line ’Search’ with
the digit buttons 0-9 .
Fine tuning
Name edit
Programme number
Decoder
(,,,,=,,,,$
xxx
01
OFF
ON
NICAM
DIf you don’t know the frequency or channel of the TV
channel of your choice, press the C button to start
the channel search.
Exit:
press MENU
f In the line ’Programme number’ select the
programme number you want e.g.: ’01’, using the D or
C button.
f Select function ’ON’ with the D or C button. When
you select ’OFF’, the function will be switched off.
g Confirm with the OK button.
g If you want to change the TV channel name, press the
h To end, press the MENU button.
C button in line ’Name edit’.
Your decoder has now been allocated to this TV channel.
E Select the character you want to change with the D or
the C button. Change the character with the B or the
A button. Select the next character in the same way.
i Press the MENU button again.
DIf you have programmed a recording (TIMER), a
wake-up timer or a sleep-timer, you can’t select the
function ’Manual store’.
E To confirm the information, press the OK button.
h In the line ’NICAM’, select funtion ’ON’ or ’OFF’ with
the C or D button.
i If you want to change the automatic tv channel setting,
select the line ’Fine tuning’.
Manual TV channel search
With the D or C button you can vary the automatic tv
channel setting. Important: This re-tuning is only
necessary and useful in special cases, e.g.: when there
are stripes on the picture with cable-TV systems.
In certain cases the ’Automatic TV channel search’ may not be
able to find all of the TV channels (e.g. coded TV channels). In
that case, use this manual method to set the channels.
a Press the MENU button on the remote control. The main
j Press the OK button to store the TV channel.
menu will appear.
DIf you want to search for further TV channels, start
b Select the line ’Installation’ with the B or
again at step e.
A button and confirm with the C button.
k To end, press the MENU button.
c Select the line ’Manual store’ with the B or
DIf you have programmed a recording (TIMER), a
wake-up timer or a sleep-timer, you can’t select the
function ’Manual store’.
A button and confirm with the C button.
MANUAL STORE
Channel/Frequency
TV system
FREQU.
PAL-BG
123
Satellite receiver
Search
Fine tuning
Name edit
Programme number
Decoder
(,,,,=,,,,$
xxx
01
OFF
ON
You can receive channels from the satellite receiver via the
scart socket EXT. 1 .
NICAM
To do this, select the channel number ’E1’ with the qP r
button. You will have to select the channels to be received by
the satellite receiver on the receiver itself.
Exit:
press MENU
6
Download from Www.Somanuals.com. All Manuals Search And Download.
E ’Time’, ’Year’, ’Month’, ’Date’ will appear on the
Special installation functions
TV screen.
You can select one of the following installation functions in
order to adapt your TV-VIDEO Combi to your own specific
requirements.
Autostore ready
CHANNELS FOUND:
08
Automatic TV channel search
Time
Year
Month
Date
15:36
2000
06
Your TV-VIDEO Combi will search for all TV channels.
If you want to start the automatic TV channel search again,
then follow the instructions below.
08
Exit:
press MENU
a Press the MENU button on the remote control. The main
menu will appear.
h Check if the time in line ’Time’ is correct. If required,
change the time with the number buttons 0-9 on your
remote control.
b Select the line ’Installation’ with the B or
A button and confirm with the C button.
c Select the line ’Autostore’ with the B or
A
i Check ’Year’, ’Month’ and ’Date’ in the same way.
button.
Switch between the entry fields with the B or
A
button.
d Press the C button.
j Confirm each line with the OK button.
e Select the country you are in with the B or A button.
If your country doesn’t show up, select ’OTH.’.
How to search for a TV channel manually, you can read in the
section ’Manual TV channel search’.
f Confirm with the OK button. The ’Automatic TV channel
search’ starts.
DIf you have programmed a recording (TIMER), a wake-up
timer or a sleep-timer, you can’t select the function
’Autostore’.
DAutomatic Channel Installation:
Searching...
Some cable companies or broadcasters offer the
possibility to install TV channels automatically with ’ACI’.
Information about the installation offered and how to
select it, will appear on the screen.
CHANNELS FOUND:
//////,,,,,,,,,,,,,,,,,,,,,
This set will recognize and install TV channels with ’ACI’
automatically.
TV channels will be stored from programme number 1
onward.
If ’ACI’ cannot identify a TV channel, you can search for it
using the method as described in the section ’Manual TV
Channel Search’.
g When the TV channel search is complete,
’Autostore ready’ will appear on the screen.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIf you have programmed a recording (TIMER), a
wake-up timer or a sleep-timer, you can’t select the
function ’Sort channels’.
Searching for new TV channels
a Press MENU . The main menu will appear.
b Select the line ’Installation’ with the B or
A button and confirm with the C button.
Delete a TV Channel
c Select the line ’Add new channels’ with the
B or A button and confirm with the C button.
Channel search will start.
a Press the MENU button. The main menu appears.
b Select the line ’Installation’ with the B or
A button and confirm with the C button .
d To store the TV channel, press OK .
c Select the line ’Sort channels’ with the B or
e Repeat step d, until you have found all desired TV
A button and confirm with the menu button C .
channels.
DIf you have programmed a recording (TIMER), a
wake-up timer or a sleep-timer, you cannot select
the function ’Add new channels’.
SORT CHANNELS
01 zzz
02 yyy
03 xxx
04 aaa
05 bbb
06 ccc
Allocating a channel number
a Press the MENU button. The main menu will appear.
Exit:
press MENU
To move:
press OK
b Select the line ’Installation’ with the B or
A button and confirm with the C button.
d With the B , A , D or C button, select the TV
c Select the line ’Sort channels’ with the B or
channel you want to delete and press the CLEAR button.
A button and confirm with the C button.
e Repeat step d, until you have deleted all the required
SORT CHANNELS
TV channels.
01 zzz
02 yyy
03 xxx
04 aaa
05 bbb
06 ccc
f To end, press the MENU button.
DIf you have programmed a recording (TIMER), a
wake-up timer or a sleep-timer, you can’t select the
function ’Sort channels’.
Exit:
press MENU
To move:
press OK
d With the B , A , D or C button, select the TV
channel to which you want to allocate a programme
number and press the OK button.
e With the B , A , D or C button, shift the TV
channel to the programme number you wish to allocate to
this TV channel and press the OK button.
f Repeat steps dto euntil you have allocated a
programme number to all the required TV channels.
g To end, press the MENU button.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the language
Setting the time and date
a Press the MENU button on the remote control. The main
You can select the language for the on-screen display (OSD).
menu will appear.
a Press the MENU button on the remote control. The main
b Select the line ’Installation’ with the buttons
menu will appear.
B or A and confirm with the button C .
c Select the line ’Set clock’ with the B or
A
button and confirm with the C button.
MAIN MENU
Picture
Sound
Setup
SET CLOCK
Tape
Installation
Time
15:36
2000
06
08
ON
Year
Exit:
press MENU
Month
Date
Smart clock
Exit:
press MENU
b Select the line ’Installation’ with the B or
A button and confirm with the C button.
d Check the time in line ’Time’. If required, please change
the time with the 0-9 buttons on the remote control.
e Check ’Year’, ’Month’ and ’Date’ in the same way.
INSTALLATION
You can switch between entry fields with B or
A
Add new channels
Sort channels
Autostore
button. Confirm with the OK button.
Manual store
Set clock
f To end, press the MENU button.
Language
ENGLISH
Automatic time and date setting
(SMART CLOCK)
Exit:
press MENU
DIf a television programme, which transmits TELETEXT, is
stored with programme number ’P01’, time and date will
be set automatically.
c Select the line ’Language’ with the B or
A
button.
DThe time will automatically be adjusted to winter time and
d Select your language with the D or C button.
summer time.
e To end, press the MENU button.
a Press the MENU button on the remote control. The main
menu will appear.
b Select the line ’Installation’ with the buttons
B or A and confirm with the button C .
c Select the line ’Set clock’ with the B or
A
button and confirm with the C button.
d Select the line ’Smart clock’ with the menu buttons
B or A .
e Switch the function on with the menu buttons D or
C .
f Confirm with the OK button.
g To end, press the MENU button.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. IMPORTANT NOTES FOR OPERATION
SUMMARY OF USER GUIDE
The OSD menu offers the following functions. More details on each can be found in the appropriate chapter.
PICTURE
MAIN MENU
Brightness
(,,,,,,,,,
(,,,,,,,,,
(,,,,,,,,,
(,,,,,,,,,
Picture
Sound
Colour
Contrast
Sharpness
Tint
Setup
Tape
Installation
NATURAL
NO
Store as pref.
Exit:
press MENU
Exit:
press MENU
Chapter ’TV FUNCTIONS’
User guide (OSD)
SOUND
The OSD (On-screen display) shows the various functions in
the form of a menu on the television screen. You can then
choose the settings you require. There is a summary of the
menus on this page. The main button functions are displayed
in a help line along the bottom of the screen.
Volume
Balance
Bass
(,,,,,,,,,
(,,,,=,,,,$
(,,,,=,,,,$
(,,,,=,,,,$
Treble
Sound mode
NEUTRAL
OFF
ON
NO
Surround
Auto volume cont.
Store as pref.
E To call up the menu: With the MENU button.
E To select a line: With the B or A button.
E To select within a line: With the D or C button.
Exit:
press MENU
Chapter ’TV FUNCTIONS’
E To enter or change your selection: With the 0-9 , D or
C button.
E To enter or change your selection in the TIMER entry
SETUP
columns: With the B or A button.
Parental control
OFF
MAX
NORMAL
ON
E To cancel: With the MENU button.
E To save: With the OK button.
E To confirm: With the C button.
E To exit the menu: With the MENU menu button.
Display
Format 16:9
Speakers
Sound only
VCR 1/2
ON
VCR
1
Exit:
press MENU
Chapter ’ADDITIONAL FUNCTIONS’
TAPE
Tape speed
Tape counter
Repeat play
Video system
Jitter
SP
LEFT
OFF
AUTO
(,,,,=,,,,$
(,,,,=,,,,$
E To confirm the messages in red on the screen: Press the
OK button.
Tracking
Cleaning
E You can switch the machine on with the qP r ,
z
Exit:
press MENU
or 0-9 button or by putting in a cassette.
Chapter ’PLAYBACK FUNCTIONS’
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Important notes for operation
E We suggest that, from now on, you switch off your
TV-VIDEO Combi with the STANDBY m button on the front
of the set or on the remote control.
When the set is in the standby mode, a small red lamp at
the front of the set will be alight.
E You can switch on with the qP r or z button, the
0-9 buttons or by inserting a cassette.
AAttention: If you use the power switch 8 on the side
panel, you switch off the set completely from the mains
power supply. No programmed recordings will then be
made. The red lamp at the front of the set will not be
alight. After some time, the date and clock settings will be
lost.
We advise you to keep your TV-VIDEO Combi connected
to the mains at all times to ensure that programmed
recordings can be made and that the television works
normally. The power consumption will be low.
E Attention: If you switch off the appliance with the power
switch 8 , make sure that you have removed the tape
by pressing the ? button.
E If you diconnect your TV-VIDEO Combi from the mains,
TIMER and channel information will remain stored for
about 1 year and clock information will remain stored for
30 minutes.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
4. TV SET FUNCTIONS
Selecting a TV programme
Volume control
Select the required TV channel (=programme number) with the You can control the volume level with the qSr button.
qP r button or with the digit buttons 0-9 on the remote
control.
If you want to mute the sound temporarily (e.g.: during a
telephone call), press the y button on the remote control.
When you press the y button again, the sound will return at
its original volume level.
DIf you don’t know the programme number of the required
TV channel:
a Press the qP r button for more than 2 seconds.
The TV channel list appears on the screen.
Sound settings
b Select the required TV channel with the qP r
button.
You can select between several sound settings, to meet your
personal sound preferences.
After 1 second the TV-VIDEO Combi will switch to
the selected programme number.
a Press the MENU button. The main menu appears.
b Select the line ’Sound’ with the B or A button and
confirm with the C button.
Picture settings
a Press the MENU button. The main menu appears.
SOUND
b Select the line ’Picture’ with the menu buttons
B
Volume
(,,,,,,,,,
(,,,,=,,,,$
(,,,,=,,,,$
(,,,,=,,,,$
NEUTRAL
or A and confirm with the menu button C .
Balance
Bass
Treble
Sound mode
Surround
OFF
Auto volume cont.
Store as pref.
ON
NO
PICTURE
Exit:
Brightness
(,,,,,,,,,
(,,,,,,,,,
(,,,,,,,,,
(,,,,,,,,,
press MENU
Colour
Contrast
Sharpness
Tint
c Select the required line with the B or A button and
NATURAL
NO
Store as pref.
alter with the D or C button.
Exit:
press MENU
E In the line ’Sound mode’ select one of these options:
’NEUTRAL’: neutral sound setting
’LOUDN.’: when the volume level is low, high and low
sound will be emphasized.
’SPATIAL’: spacious stereo effect
c Select the required line with the menu buttons B or
A and alter with the menu buttons D or C .
D’Contrast Plus’: Enhances TV contrast by whitening
DTo store a setting as a standard setting, select the
the white and blackening the black.
line ’Store as pref.’ with the B or
button. Select ’YES’ and confirm with the OK
button.
A
DTo store this setting as a standard setting, select the
line ’Store as pref.’ with the menu buttons
B or A . Select ’YES’ and confirm with the
OK button.
DTo call up the standard settings, switch the set off
and on again or select ’Smart Sound’ setting
’Personal’.
DTo call up the standard settings, switch the set off
and on again or select ’Smart Picture’ setting
’Personal’.
Switching Incredible Surround on or off
a To switch on the ’Incredible Surround’ effect, in the line
Selecting the picture setting
(SMART PICTURE)
’Surround’ select ’ON’ with the D or C button.
E You can always simply switch the function on or off with
D’SMART PICTURE’: Optimises all picture settings using a
the SURROUND button on the remote control.
single button on the remote control.
DIf Surround Sound is switched on, the line ’Sound
E Press the SMART button repeatedly to select the
mode’ in the Sound menu will be deactivated.
required picture setting.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a preset sound setting (SMART
SOUND)
Extra TELETEXT functions
To use the extra TELETEXT functions, press the MENU button,
when you are in TELETEXT.
D’SMART SOUND’: provides a choice of sound settings
from the remote control.
E To enlarge the print, select the symbol ’g’ and confirm
with the OK button.
E Press the SMART # button repeatedly to select the
desired sound setting.
E To switch off the TELETEXT decoder temporarily, select
the symbol ’d’ and confirm with the OK button.
DIf the Surround function is switched on, ’Smart Sound’
will be switched to ’Manual’.
E To call up a TELETEXT sub-page:
a Select the symbol ’}’ and confirm with the OK
Automatic volume control (AVL)
button.
E Switch on ’Auto volume cont.’, to activate the
automatic volume control. This will minimise sudden
changes in TV volume, e.g. when commercial spots are
being transmitted or when switching TV channels.
b Enter the page number of the sub-page with the
0-9 -buttons (e.g.: 0123).
E To call up concealed information, select the symbol ’b’
and confirm with the OK button.
DThe AVL function will only affect the internal speakers.
E To stop the pages from being turned over, select the
symbol ’f’ and confirm with the OK button.
E To show TELETEXT transparently, select the symbol ’-’
Sound track selection
and confirm with the OK button.
You can select the required sound track. This is of particular
interest when audio transmissions are multilingual.
E Press the AUDIO button to select one of the following
options:
STEREO transmissions: ’Stereo’ and ’Mono’
Multilingual transmissions: ’Dual I’ and ’Dual II’
DWhile a tape is playing, you can also select one of the
following modes: ’Left’, ’Right’, ’Mix’. In the ’Mix’
mode you can play the mono sound of the normal (linear)
audio track together with the sound of the stereo audio
track. You can play cassettes that have been dubbed on
another video recorder.
How to read TELETEXT
E Press the TELETEXT e button to switch the TXT decoder
on and off. The TV-VIDEO Combi is now receiving the TXT
of the TV channel currently selected.
E To store the current page as preferred page, press the
OK button.
The next time you call up TELETEXT, you will
automatically turn to this page.
E If you want to select an other page, type in the number of
the page with the digit buttons 0-9 . With the colour
buttons on your remote control you can directly select
the page numbers shown at the bottom of the TV screen.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
5. PLAYBACK FUNCTIONS
Playing a cassette
Searching for tape position with the picture
(picture search)
a Put a cassette into the cassette slot.
b Press the PLAY G button.
a While a cassette is playing, press the H (reverse) or
I (forward) button once or several times.
E If you press the STOP h button once, the TV-VIDEO
Combi will switch to pause. To stop, press the STOP h
button again.
b To stop at a certain picture, press the PLAY G button.
DDuring picture search, the picture quality may not be
so good and there will be no sound.
E To eject the cassette, press the ? button on the
TV-VIDEO Combi or press the STOP h button on the
remote control several seconds.
Still picture
a Press the STILL R button. A still picture will appear on
DBefore transportation, make sure that no cassette is
the screen.
in the TV-VIDEO Combi.
b Each time you press STILL R again, the picture will
DIf you insert an erase protected cassette, the
move on one step.
TV-VIDEO Combi will automatically start playback.
DSome hired cassettes may have poor picture or
sound quality. This is not a fault in your machine.
Please read ’Eliminating picture interference’.
Slow motion
a Press the STILL R button. A still picture will appear on
the screen.
DSome functions will automatically switch off after a
while (for example, pause, still picture, picture
search). This helps to protect the cassette and
avoids wasting power.
b When you hold the STILL R button, the tape will be
played in slow motion.
c When you press the I button several times, you have
a choice of several playback speeds.
During slow motion there will be no sound.
Playing an NTSC cassette
With this set you can play cassettes that have been recorded
on another video recorder in the NTSC standard (for example,
American cassettes).
Searching for tape position without the
picture (wind and rewind)
a Stop the tape with the STOP h button.
b Press the H (reverse) or I (forward) button.
c To stop at a certain picture, press the STOP h button.
DSome special features (for example, still picture) are not
possible while you are playing an NTSC cassette.
Instant View
Tape position indication
With this function you can switch to picture search during
wind and rewind.
DPress the OK button to display the current tape position.
DTo change the type of tape position display, proceed as
a If you hold the H (rewind) or I (wind) button
follows:
during wind or rewind, you will switch to picture search.
a During playback, press the MENU button.
b When you release the button, the TV-VIDEO Combi will
automatically switch back to rewind or wind.
b Select the line ’Tape’ with the menu buttons B or
A and confirm with the C button.
Automatic search for a tape position (index
search)
At the start of each recording, the TV-VIDEO Combi will write
an index code on the tape.
c Select the line ’Tape counter’ with the menu
buttons B or A .
d With the menu buttons D or C select ’USED’ to
check the time used, or ’LEFT’ to check the time left on
the tape.
a Press the INDEX E button. Press the I button to
select the next code mark or the H button for the
previous code mark.
e Confirm with the OK button.
b When the TV-VIDEO Combi finds the code mark, it will
automatically switch to play.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture interference
Cleaning the video heads
If horizontal lines appear on the screen when you play a
cassette, you should clean the video heads.
When the picture quality is poor when you play a cassette,
please follow these instructions.
Tracking during playback
a During playback, press the MENU button.
b Select the line ’Tape’ with the buttons B or A and
confirm with the C button.
c Select the line ’Tracking’ with the buttons B or
A .
d Hold the buttons D or C until the playback quality is
at its best.
e Confirm with the OK button.
a During playback, press the MENU button.
f To end, press the MENU button. This setting will remain
b Select the line ’Tape’ with the menu buttons B or
until you remove the cassette.
A and confirm with the C button.
c Select the line ’Cleaning’ with the menu buttons
Tracking during still picture
If the still picture vibrates vertically, you can improve the still
B or A .
d Press the OK button. ’CLEANING’ appears on the
picture as follows:
screen.
a During still picture, press the MENU button.
e Wait a few seconds, until the message disappears and
b Select the line ’Tape’ with the B button or A and
then press the MENU button.
confirm with the C button.
c Select the line ’Jitter’ with the B or A button.
d Hold the D or C button until the picture quality is at
its best.
e Confirm with the OK button.
f To end, press the MENU button.
DPlease note, however, that interference may still
occur with poor quality cassettes.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
6. MANUAL RECORDING
Use ’Manual Recording’ to make a spontaneous recording (for
example, a programme currently being shown).
Protecting your recordings
So that you don’t accidentally delete an important recording,
remove the special tab on the narrow side of the cassette with
a screwdriver or slide the special tab to the left. Later, if you
no longer want to protect your recording, you can seal the gap
again with sticky tape or slide the special tab to the right.
E If you want to start and stop a recording manually, read
the section: ’Recording without automatic switch-off’.
E If you want to start a recording manually but have it
stopped automatically, read the section: ’Recording with
automatic switch-off’.
Auto-assembling
Recording without automatic switch-off
You can use the auto-assembling function to join individual
recordings without any major picture disturbance between
them.
a Insert a cassette.
b Use the qP r button to select the programme number
you want to record, for example, ’P01’.
a While the cassette is playing, search for the correct
DProgramme number ’E1’ is provided for recording
position on the tape.
from external sources (via the EXT. 1 scart socket).
b Stop the cassette by pressing the STOP h button.
’Pause’ will appear on the TV screen.
DProgramme number ’AV’ is provided for recording
from external sources (via the Audio/Video socket
AUDIO L/R at the front of the TV-VIDEO Combi).
c Now start recording as usual by pressing the
RECORD/OTR n button on the remote control.
c To start recording, press the RECORD/OTR n button on the
remote control or 5 on the TV-VIDEO Combi.
When you are recording, the red recording light at the
front panel of the TV-VIDEO Combi will be lit.
Selecting the recording speed (SP or LP)
You can reduce the recording speed by half. This makes it
possible to record, for example, eight-hours instead of
four-hours on an ’E240’ (four-hour) cassette.
d Stop recording with the STOP h button.
DIf you want to switch off the screen while recording,
press the STANDBY m button once .
a Press the MENU button. The main menu appears.
DTo switch the screen back on again, press the
b Select the line ’Tape’ with the B or A button, and
qP r button.
confirm with the C button.
DDuring a recording you can watch other TV
c Select the line ’Tape speed’ with the B or
A
channels.
button.
d Select the required recording speed with the D or
C button.
Recording with automatic switch-off
(OTR one-touch-recording)
D’LP’: Long Play = half recording speed (double
recording time).
’SP’: Standard Play = normal recording speed.
a Put a cassette in the machine.
DThe picture quality will be adversely affected when
b Use the qP r button to select the programme number
recording at half recording speed (’LP’).
you want to record.
DFor playback, the correct recording speed will
c Press the RECORD/OTR n button on the remote control.
When you are recording, the red recording light at the
front panel of the TV-VIDEO Combi will be lit.
automatically be selected.
e Confirm with the OK button.
f To end, press the MENU button.
d Press the RECORD/OTR n button again and again until the
display on the TV-VIDEO Combi shows the desired end
time or length of the recording.
DTo cancel this information, press the CLEAR button.
e Confirm with the OK button.
f To end, press the MENU button.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
7. PROGRAMMED RECORDING (TIMER)
Use programmed recording to automatically start and stop a
recording at a later date.
c Enter the entire SHOWVIEW-number (up to 9 digits)
printed in your TV guide next to the start time of a TV
programme.
To make a programmed recording, your TV-VIDEO Combi
needs to know:
For example, 5-234-89 or 5 234 89
Enter 523489 for the SHOWVIEW-number.
If you make a mistake, you can clear your instructions
with the CLEAR button.
* the date you want to make the recording;
* the programme number for the TV channel you want to
record;
* the start and stop time of the recording;
* whether you want to use VPS or PDC;
* the recording speed (SP/LP).
ShowView
The TV-VIDEO Combi stores all the information in a TIMER
block. You can programme up to 6 TIMER blocks a month in
advance.
CODE
REPEAT
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
1
2
3
4
5
6(
(
(
ONCE
0-9
Store:
press OK
’VPS’ (Video Programming System) and
’PDC’ (Programme Delivery Control)
With ’VPS and PDC’, the TV station controls the start time and
the length of the recording. This means that the TV-VIDEO
Combi switches itself on and off at the right time even if a TV
programme you want to record begins earlier or finishes later
than expected.
Usually the start time is the same as the VPS or PDC time. But
if your TV guide gives a VPS or PDC time which is different to
the programme’s start time (for example, 20.15 and VPS 20.14),
you must enter ’20.14’ as the start time.
d In line ’REPEAT’ select the kind of programming
required with the B or A button.
’ONCE’: recording only once
’Mo-Fr’: recordings every day from Monday to Friday.
’Mo-Su’: recordings every day from Monday to Sunday.
’WEEKLY’: recordings every week on the same day of
the week.
e Confirm with the OK button. Your programming details
will then appear on the TV screen.
If you want to programme a time that is different from the VPS
or PDC time, you must switch off VPS or PDC.
TIMER PROGRAMMING
VPS
DATEPROG. START END
LP PDC REP.
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
15 xxx
15:36 15:50
-
*
ONCE
Programming a recording
(with ’SHOWVIEW’)
All the important information needed for a programming is
contained in the SHOWVIEW-programming number.
Store:
press OK
DIf SHOWVIEW does not recognise the TV channel,
’P??’ will appear on the TV screen. Instead of
’P??’, you can select the programme number
(programme name) you want with the number
buttons 0-9 .
a Press the TIMER s button on the remote control.
b Select the line ’ShowView’ with the menu buttons
B or A and confirm with the C button.
DIf ’Code error’ appears on the TV screen, this
means you entered an incorrect SHOWVIEW-code
number or the incorrect date. Correct your
instructions or end with the TIMER s button.
DIf ’Daily error’ appears on the TV screen, the
date was incorrectly entered.
DUnder ’VPS/PDC’, use the B or A button to
switch ’VPS or PDC’ on or off.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DUnder ’LP’, use the B or A button to select the c Press the C button.
recording speed ’SP’ or ’LP’.
DThe TIMER lamp on the front of the set will light up
when one or more of the TIMER blocks are
occupied.
TIMER PROGRAMMING
VPS
DATEPROG. START END
LP PDC REP.
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
15 xxx
15:36 15:50
-
*
ONCE
DWhen you are recording, the red recording light at
the front of the TV-VIDEO Combi will be alight.
DIf the end of the cassette is reached during a
recording, the TV-VIDEO Combi will automatically
eject the cassette.
Store:
press OK
DIf you forgot to insert cassette, ’No cassette’
d Select the entry field with the D or C button.
will appear.
e Enter information with the menu buttons B or A or
DIf you have inserted a cassette with erase protection
when you want to start a recording, the cassette will
be ejected.
with the digit buttons 0-9 .
DUnder ’REP.’, use the B or A button to select
daily or weekly programming.
f Press the OK button.
g Confirm the message on the screen with the OK button.
A TIMER recording can only start, if the set is not used for
other video recorder functions (e.g. playback).
’ONCE’: Recording only once.
’Mo-Fr’: Recording from Monday to Friday.
’Mo-Su’: Recording from Monday to Sunday.
’WEEKL’: Recording every week on the same day.
h To end, press the TIMER s button.
DUnder ’VPS/PDC’, use the B or A button to
switch ’VPS or PDC’ on or off.
DUnder ’LP’, use the B or A button to select the
Programming a recording
(without ’SHOWVIEW’)
recording speed ’SP’ or ’LP’.
f Press the OK button.
g Confirm the message on the screen with the OK button.
A TIMER recording can only start, if the set is not used for
other video recorder functions (e.g. playback).
a Press the TIMER s button on the remote control.
b Select the line ’TIMER PROGRAMMING’ with the
menu buttons B or A and confirm with the
C
button.
h If you have confirmed with the OK button, exit the menu
with the TIMER s button.
E The programming information has been stored in a TIMER
TIMER PROGRAMMING
VPS
block.
DATEPROG. START END
LP PDC REP.
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
i Make sure that the cassette you have put in can be
--
--
--:-- --:---
-
-----
recorded on.
Exit:
press TIMER
Start:
press
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DUnder ’REP.’, use the B or A button to select
daily or weekly programming.
Programming a recording with TELETEXT
’ONCE’: Recording only once.
With this function programming a recording will be
considerably easier. In TELETEXT you select the TV
programme you want to record. All the required information
for recording will be transferred and stored in a TIMER block.
You can find more information on TELETEXT in the chapter ’TV
SET FUNCTIONS’.
’Mo-Fr’: Recording from Monday to Friday.
’Mo-Su’: Recording from Monday to Sunday.
’WEEKL’: Recording every week on the same day.
DUnder ’VPS/PDC’ switch ’VPS/PDC’ on or off with
the B or A button.
a Select the TV channel you want to record from.
b Press TELETEXT e to activate TELETEXT. Your TV-VIDEO
Combi will now show TELETEXT for the TV channel you
have selected.
DUnder ’LP’ select the recording speed ’SP’ or ’LP’
with the B or A button.
h When all information is correct, press OK .
i Confirm the message on the screen with OK .
A Timer recording can only start, if the set is not being
used for other video recorder functions (e.g. playback).
c With the number buttons 0-9 select the TELETEXT
programme guide page. This page can be stored as the
preferred page (see paragraph ’How to read TELETEXT’).
DThe programming information has been stored in a
d Press TIMER s . ’PLEASE WAIT...’ will briefly
appear at the bottom of the screen.
TIMER block.
j Exit the menu with the TIMER s button.
Next, a highlighted title line will appear.
k Make sure that the cassette you have put in can be
DIf ’NO TIMER INFORMATION ON THIS
PAGE’ appears, TELETEXT programming cannot be
used for the programme you have selected. In this
case, you should programme the recording as
described in the paragraph ’programming a
recording’.
recorded on.
Automatic recording from a satellite
receiver (SAT RECORDING)
e A cursor (h) will appear at the first programme line. Use
the B and A buttons to move the cursor (h) to the TV
programme you want to record.
You can use this function if you own a satellite receiver that
can control other machines via a scart cable and a
programming function.
DIf you want to cancel this function, press
a Press TIMER s on the remote control.
TELETEXT e .
b Select the line ’TIMER PROGRAMMING’ with the
f Press OK . The timer menu will appear. The required
programming information has been stored in a TIMER
block. Please check the information.
B or A button and confirm with C .
TIMER PROGRAMMING
VPS
DATEPROG. START END
LP PDC REP.
TIMER PROGRAMMING
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
VPS
DATEPROG. START END
LP PDC REP.
--
--
--:-- --:---
-
-----
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
15 xxx
15:36 15:50
-
*
ONCE
Exit:
press TIMER
Start:
press
Store:
press OK
g For changing the timer information, select the entry field
with the D or C button. Change the information with
the B or A button or with the number buttons 0-9 .
19
Download from Www.Somanuals.com. All Manuals Search And Download.
c Press C .
DEach time you programme a recording on the
satellite receiver, you must prepare your TV-VIDEO
Combi for recording. Each time you prepare your
TV-VIDEO Combi for a satellite recording a
TIMER-block will be reserved and the TIMER light at
the front will blink.
TIMER PROGRAMMING
VPS
DATEPROG. START END
LP PDC REP.
,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
15 xxx
15:36 15:50
-
*
ONCE
DIf the TIMER light does not blink, you have not set
the clock or all TIMER-blocks have been used up.
Please read the paragraph ’Setting the time and
date’ or ’How to clear a programmed recording
(TIMER)’.
Store:
press OK
DIf you want to cancel the programmed SAT
recording, follow the procedure described in the
paragraph ’How to clear a TIMER’.
d Select the entry field ’PROG.’ with the D or
C
button. Select ’Record prepared’ with the B or
A button.
e Confirm with the OK button.
Your TV-VIDEO Combi is now prepared for recording. The
start and end of the recording is controlled via the scart
cable.
How to check or change a TIMER
a Press the TIMER s button on the remote control.
f To end, press the TIMER s button.
g Place a cassette in the machine.
E If you have not connected the satellite receiver yet, use a
scart cable to connect scart socket EXT. 1 on the
TV-VIDEO Combi to the corresponding scart socket on
the satellite receiver.
b Select the line ’TIMER PROGRAMMING’ with the
menu buttons B or A and confirm with the
C
button.
c Select the TIMER you want to check or change with the
B or A button and confirm with the OK button.
d Select the entry field with the D or C button.
h Programme the satellite receiver with the required
information (programme number on the SAT receiver,
start time, end time).
e Change any information with the B or A button or
with the 0-9 buttons.
DUnder ’LP’, use the B or A button to select the
DThe information on how to programme your satellite
receiver can be found in the instruction manual for
your satellite receiver.
recording speed ’SP’ or ’LP’.
f Confirm with the OK button.
g To end, press the TIMER s button.
Activating a recording from the SAT
receiver with OTSR (OTSR = One Touch Sat
Recording)
h Make sure that the cassette you have put in can be
recorded on.
In the previous paragraph we described how to prepare the
TV-VIDEO Combi for recording from the SAT receiver by
means of the menu (step a through f ). OTSR will allow
you to record a SAT programme fast and easy with just one
button press.
How to clear a TIMER
a Press the TIMER s button on the remote control.
b Select the line ’TIMER PROGRAMMING’ with the
menu buttons B or A and confirm with the
C
a Press the Sr/q buttons at the same time until the
timer light on your TV-VIDEO Combi starts blinking. It will
blink three times and will then stay alight.
button.
c Select the TIMER you want to clear with the menu
buttons B or A .
Your TV-VIDEO Combi is now prepared for recording. The
start and end of the recording is controlled via the scart
cable.
d Press the CLEAR button.
e Switch off with the TIMER s button.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
8. ADDITIONAL FUNCTIONS
Changing the TV system
Parental control
If you play back recordings made on a different kind of tape
(for example, NTSC standard), the automatic TV system
switch-over may lead to colour interferences. You can switch
off the ’automatic TV system switch-over’ as follows.
This function will prevent unauthorised use of your TV-VIDEO
Combi. All button-functions will be locked.
DYou can make programmed recordings while the parental
control is on.
a Press the MENU button. The main menu appears.
a Press the MENU button. The main menu will appear.
b Select the line ’Tape’ with the B or A button and
b Select the line ’Setup’ with the B or A button and
confirm with the C button.
confirm with the C button.
TAPE
SETUP
Tape speed
Tape counter
Repeat play
Video system
Jitter
SP
LEFT
OFF
Parental control
OFF
MAX
NORMAL
ON
AUTO
(,,,,=,,,,$
(,,,,=,,,,$
Display
Format 16:9
Speakers
Tracking
Cleaning
Sound only
VCR 1/2
ON
VCR
1
Exit:
press MENU
Exit:
press MENU
c In the line ’Video system’ select the required TV
c In the line ’Parental control’ select ’ON’ with
system with the menu buttons D or C .
the D or C button.
d Confirm with the OK button.
d Confirm with the OK button.
e To end, press the MENU button.
e To end, press the MENU button.
Keep the remote control in a safe place.
f Switch off the machine with the STANDBY m button.
DIf you want to switch off parental control, select
’OFF’ in line ’Parental control’.
DIf a button is pressed with activated parental
control, ’Parental Control active’ will
appear.
DIf you have activated parental control, you can only
operate the TV-VIDEO Combi with the remote
control.
DIf you want to eject a cassette with activated
parental control, press the STOP h button several
seconds.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the On-screen display (OSD) on
or off
Switching to 16:9 wide screen picture
If you are using a cassette with 16:9 wide screen recordings,
you can switch this function ’ON’. The TV-VIDEO Combi will
now automatically switch to wide screen.
You can switch the On Screen Display of the current operating
information on or off.
a Press the MENU button. The main menu appears.
a Press the MENU button. The main menu appears.
b Select the line ’Setup’ with the B or A button and
b Select the line ’Setup’ with the menu buttons B or
confirm with the C button.
A and confirm with the C button.
SETUP
SETUP
Parental control
OFF
MAX
NORMAL
ON
Parental control
OFF
MAX
NORMAL
ON
Display
Display
Format 16:9
Speakers
Format 16:9
Speakers
Sound only
VCR 1/2
ON
Sound only
VCR 1/2
ON
VCR
1
VCR
1
Exit:
press MENU
Exit:
press MENU
c Select the line ’Format 16:9’ with the A or
B
c Select the line ’Display’ with the menu buttons
B
button.
or A .
d Select one of the possibilities with the C or D button.
’NORMAL’ : Normal size picture.
d Select one of the options indicated with the menu buttons
C or D .
’EXTEND.’ : Extended size picture.
’COMPR.’ : 16:9 format picture.
’MAX’: The OSD appears for a few seconds each time an
operating mode is selected and then disappears.
’MIN’: The OSD is reduced to a minimum.
’PROGR.’: The programme number is always shown.
’COUNTER’: The tape position is always shown.
DWhen you watch TV you can select between
’EXTEND.’ and ’NORMAL’.
e Confirm with the OK button.
e Confirm with the OK button.
f To end, press the MENU button.
f To end, press the MENU button.
DWith the OK button you can superimpose the On
Screen Display of current operating mode on the TV
screen.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the internal speakers on or off
Switching the remote control command
If you want to connect a HiFi-stereo set or a ’Dolby Pro Logic’
decoder to the socket AUDIO OUT L/R (audio output left/right)
and switch off the internal speakers, proceed as follows:
If you have two machines with the same remote control
command, you can change the remote control command of the
handset and the remote control command of your TV-VIDEO
Combi.
a Press the MENU button. The main menu will appear.
a Press the MENU button. The main menu appears.
b Select the line ’Setup’ with the B or A button and
confirm with the C button.
b Select the line ’Setup’ with the menu buttons B or
A and confirm with the menu button C .
SETUP
SETUP
Parental control
OFF
MAX
NORMAL
ON
Display
Parental control
OFF
MAX
NORMAL
ON
Format 16:9
Speakers
Display
Format 16:9
Speakers
Sound only
VCR 1/2
ON
VCR
1
Sound only
VCR 1/2
ON
VCR
1
Exit:
press MENU
Exit:
press MENU
c Select the line ’Speakers’ with the B or A .
c Select the line ’VCR 1/2’ with the menu buttons
B
or A .
d In the line ’Speakers’ select ’OFF’ with the D or
C button.
d Select ’VCR 1’ or ’VCR 2’ with the menu buttons
D or C .
e Confirm with the OK button.
e Confirm with the OK button.
f To end, press the MENU button.
DIf you want to switch the speakers on again, select
f On the remote control, press the STOP h button and the
digit button 2 at the same time to switch the remote
control to ’VCR 2’.
’ON’ in line ’Speakers’.
DIf you want to switch back to ’VCR 1, press the
STOP h button and the digit button 1 at the same
time.
g Confirm with the STOP h button.
h To end, press the MENU button.
DAfter you changed the batteries in the remote
control, it will switch back to ’VCR 1’.
DIf e.g.: ’VCR 1’ appears on the TV screen after
pressing a button for a few seconds, you must
switch the remote control to ’VCR 2’.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Continuous playback
Sound playback without picture
You can automatically play a cassette again and again. When
the end of the tape or the recording has been reached, it will
rewind and start again.
To play sound only, you can switch off the picture. You will
hear sound only.
a Press the MENU button. The main menu appears.
a Press the MENU button. The main menu appears.
b Select the line ’Setup’ with the B or A button and
b Select the line ’Tape’ with the menu buttons B or
confirm with the C button.
A . Confirm with the menu button C .
SETUP
TAPE
Tape speed
Tape counter
Repeat play
Video system
Jitter
SP
Parental control
OFF
MAX
NORMAL
ON
LEFT
Display
OFF
Format 16:9
Speakers
AUTO
(,,,,=,,,,$
(,,,,=,,,,$
Sound only
VCR 1/2
ON
VCR
Tracking
Cleaning
1
Exit:
press MENU
Exit:
press MENU
c Select the line ’Sound only’ with the B or
A
c Select the line ’Repeat play’ with the menu buttons
button.
B or A .
d Switch the function on or off with the D or C button.
e Confirm with the OK button.
d Select ’ON’ with the menu buttons D or C . If you
select ’OFF’, the function will be switched off.
e Confirm with the OK button.
f Press the MENU button.
f Press the MENU button.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch off function (SLEEP TIMER)
You can programme your set to switch off after a
predetermined period.
a Press the TIMER s button on the remote control.
b Select line ’Sleep timer’ with the B or
A
button and confirm with the C button.
c Determine the time left until switch off in 15 minutes
intervals using the B or A button.
DYou can switch the function off with the CLEAR
button on the remote control.
d Confirm with the OK button.
e To end, press the TIMER s button.
Switch on function (WAKE-UP TIMER)
You can programme your set to switch on at a predetermined
time.
a Press the TIMER s button on the remote control.
b Select line ’Wake-up timer’ with the B or
A
button and confirm with the C button.
c Select the entry field with the D or C button.
d Enter the information with the B or A button or with
the number buttons 0-9 .
e In the line ’ON’, switch the function on or off.
f Press the OK button.
g To end, press the TIMER s button.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Before you call an engineer
If, contrary to expectation, you have any problems using this
TV-VIDEO Combi, it may be caused by one of the reasons
mentioned below. You can also call the customer service
centrein your country.
You will find the phone number in the enclosed guarantee
leaflet. Have the model number (MODEL NO) and the
production number (PROD.NO) of your video recorder ready.
Programmed recording does not work:
•
•
You have not set the TIMER properly: check the TIMER blocks.
You have programmed the wrong time or date: check time and
date.
•
•
You have put in a cassette that cannot be recorded on: undo the
erase protection on the cassette.
’PDC’ or ’VPS’ switched on but ’PDC/VPS time’ wrong: enter PDC
or VPS time exactly to the minute. Have the aerial checked.
No sound from speakers:
Technical problem:
•
Speakers switched off: To switch on the speakers, turn to
chapter ’ADDITIONAL FUNCTIONS’, section ’Switching the
internal speakers on or off’.
•
You can reset the settings on your set (careful: all information will
be deleted): with the video recorder switched on, hold the
H and the I button until the screen switches off.
Recording starts as soon as the satellite receiver or second
video recorder is switched on:
Your TV-VIDEO Combi does not respond to any button being
pressed:
•
Externally controlled recording switched on: Switch off the
externally controlled recording.
•
•
There is no power supply: check the power supply
A programmed recording is currently being made: to cancel the
programmed recording, press STANDBY m for several seconds.
Parental control is on: switch the parental control off.
•
•
The TIMER lamp on the front of the set will light up although
you didn’t have programmed a TIMER block:
Continuous playback is on: switch the continuous playback off.
•
You have accidentally pressed the buttons Sr/qx on the
front of the set and so activated the Sat recording. Cancel the
recording as shown in the section ’How to clear a programmed
recording (TIMER)’.
Cassette is jammed in the TV-VIDEO Combi:
•
Don’t use force. Switch off with the 8 power switch for 30
seconds, then switch it on again.
Remote control does not work:
’Smart Clock’ setting does not work:
•
Remote control not pointed toward the TV-VIDEO Combi: point it
at the TV-VIDEO Combi.
•
You have stored a TV channel on programme number ’P01’ that
does not transmit TELETEXT: On ’P01’ store a TV channel that
transmits TELETEXT.
•
•
Batteries have run out: change the batteries.
You have given the wrong remote control command: read
’Switching remote control command’ in chapter ’Additional
functions’.
•
•
Poor TELETEXT reception: On ’P01’ store a TV channel with
good TELETEXT reception.
You have not activated the Smart Clock function: Switch the
function ’ON’.
No picture when you play a cassette:
•
There is no recording on the cassette: change the cassette.
You hear a very short and soft noise coming from your
TV-VIDEO Combi at 3:00 at night:
•
’Smart Clock’ is checking the time: Switch off the Smart Clock
function.
Poor picture quality when you play a cassette:
•
•
The cassette badly worn or of poor quality: use new cassette.
Tracking is not properly adjusted or the video heads are dirty:
turn to chapter ’PLAYBACK FUNCTIONS’ and read the section
’Cleaning the video heads’.
TELETEXT does not start at page 100:
•
You have stored a different preferred page: Store page 100 as
preferred page.
•
•
Read the section ’Picture interference’.
You are playing a cassette with a LongPlay recording on it:
Excellent picture quality is only guarateed with recordings made
in StandardPlay recording speed.
The TV-VIDEO Combi will not record:
•
The TV channel you want to record is not stored or you selected
the wrong programme number: check TV channels stored.
You have loaded a cassette which cannot be recorded on: undo
the erase protection on the cassette.
•
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical terms used
Current tape position : The part of the tape currently being
played.
External source : A device connected via a socket (for
example, scart socket) which is transmitting audio/video
signals to the TV-VIDEO Combi.
Index marking : A marking which is automatically made on the
tape at the beginning of every recording. This marking
(recording ID) can be searched for with the Index search
function.
Scart cable : Also known as a Euro-AV cable. This standard
cable is an easy method of connecting various TV, audio and
video devices, such as a HIFI and Dolby Surround set, video
recorder, DVD player, SAT receiver, decoder, computer and
similar devices. Other signals in addition to audio and video
signals can be transmitted on it.
TV system : There are various systems for transmitting
television signals, for example, PAL, SECAM, PAL BG, SECAM
DK, SECAM L/L, NTSC etc. The system used by your television
depends on which country you are in.
TXT : Also known as Teletext, Fasttext, Videotext, FLOF etc.
OTR : One touch recording. This function enables you to select
the switch-off time in intervals of 15 minutes.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
|