Waves
1
2
Connect the small curling attachment to the handle. Slide the slide-on brush
onto the curling attachment.
HP4696/17
Take a lock of hair and wind it round the slide-on brush (Fig. 7).
Prevent the slide-on brush from getting tangled in the hair in the following way:
-
-
-
Do not put too much hair in one lock.
Do not wind a lock of hair more than twice round the slide-on brush.
When you unwind a lock of hair, make sure that you hold the slide-on brush
away from the underlying hair.
3
4
Remove the slide-on brush from your hair after 5 to 10 seconds.
Let the waves cool down before you comb, brush or finger-comb the hair into
its final style.
Small ringlets
1
2
Connect the twisted curling attachment to the handle.
Take a lock of hair, press the lever to open the clip and place the lock between
the barrel and the clip (Fig. 8).
Note: Make sure that you wind the end of the lock in the required direction.
3
4
Open the clip after 5 to 10 seconds and remove the barrel from the hair.
Let the ringlets cool down before you comb, brush or finger-comb the hair
into its final style.
Large ringlets
1
2
3
Connect the large curling attachment to the handle. Slide the slide-on spiral
onto the curling attachment.
Take a lock of hair, press the lever to open the clip and place the lock between
the barrel and the clip (Fig. 9).
Release the lever and slide the barrel to the end of the lock.Then wind the
lock round the barrel following the spiral profile.
Note: Make sure that you wind the end of the lock in the required direction.
4
5
Open the clip after 5 to 10 seconds and remove the barrel from the hair.
Let the ringlets cool down before you comb, brush or finger-comb the hair
into its final style.
Flicks
1
2
Connect the straightening attachment to the handle.
Slide the straightening plates into the attachment with the curved sides
pointing towards each other (Fig. 10).
u
4222.002.6848.3
3
Take a lock of hair (max. 5 to 6cm wide). Press the lever to open the
straightening attachment and place the lock between the plates (Fig. 11).
Environment
Decide if you want to create inward or outward flicks. Hold the appliance in such a
way that the curved sides of the plates create the desired type of flick.
-
Do not throw away the appliance with the normal household waste at the end
of its life, but hand it in at an official collection point for recycling. By doing this,
you help to preserve the environment (Fig. 14).
4
Slide the styler gently down the length of the hair in a few seconds.When the
plates are 3-5cm above the end of the lock, slightly twist the appliance inwards
or outwards to create the desired type of flick.
Guarantee & service
Sleek look
If you need service or information or if you have a problem, please visit the Philips
country (you find its phone number in the worldwide guarantee leaflet). If there is no
Consumer Care Centre in your country, go to your local Philips dealer.
1
2
Press the lever to open the straightening attachment.
Remove the straightening plates one by one. Grab the cool tip and pull
each plate out of the straightening attachment (Fig. 12).
Troubleshooting
3
Turn the plates round and slide them back into the attachment with the flat
sides pointing towards each other (Fig. 13).
This chapter summarises the most common problems you could encounter with the
appliance. If you are unable to solve the problem with the information below, contact
the Consumer Care Centre in your country.
You can now use the straightening attachment to create sleek hair without flicks.
Make sure that the edges of the plates are inserted properly into the grooves.
Problem
Solution
4
Take a lock of hair (max. 5 to 6cm wide). Press the lever to open the
straightening attachment and place the lock between the plates.
The appliance does
not work.
Perhaps there is a power failure or the socket is not live. Check if the
power supply works. If it does, plug in another appliance to check
whether the socket is live.
5
6
Slide the styler gently down the length of the hair in a few seconds.
Let the sleek hair cool down before you comb or brush it.
Perhaps the appliance is not suitable for the mains voltage to which
it is connected. Make sure that the voltage indicated on the appliance
corresponds to the local mains voltage.
Cleaning
Perhaps the mains cord of the appliance is damaged. If the mains cord
is damaged, you must have it replaced by Philips, a service centre
authorised by Philips or similarly qualified persons in order to avoid
a hazard.
Never immerse the appliance in water or any other liquid, nor rinse it under the tap.
1
2
Unplug the appliance.
Place the styler on the support of the attachment in a safe place and let it cool
down.
The styling results are Perhaps you did not let the appliance heat up long enough. Let the
not satisfactory.
appliance heat up until the ready dot changes colour.
3
Clean the appliance and the attachments with a small brush or a dry cloth.
Perhaps you wound too much hair round the barrel or put too much
hair between the plates.When you use the curling attachments or the
slide-on brush, do not make the locks too thick.The thinner the lock
of hair, the tighter the curl.When you use the straightening attachment,
make sure the locks are no wider than 5 to 6cm for a good result.
Storage
1
2
Unplug the appliance.
Place the styler on the support of the attachment in a safe place and let it cool
down.
Perhaps you did not leave the styling attachment in your hair long
enough. Keep the styler in your hair for 5 to 10 seconds, depending on
the thickness of your hair.
3
Store the appliance in a safe and dry place.
Do not wind the mains cord round the appliance.
Download from Www.Somanuals.com. All Manuals Search And Download.
|