Philips Stereo System SACD 1000 User Manual

00_SACD_USA_COV_23801_D1 11-12-2000 15:52 Pagina 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
01_SACD1000_USA_23811_D1 11-12-2000 16:13 Pagina 14  
Rear of player  
VOLTAGE SELECT(or)  
- For selecting 100/120V or 220/240V. If necessary,  
adjust the selector to match your local power  
supply.  
POWER SUPPLY  
- Power supply socket for connection to the power supply.  
Filter switch  
- See chapter ‘Operation - Enhanced use’.  
GND  
- Ground connector. For making grounding connection between the  
various components of your system in case of disturbance problems.  
Also see ‘System grounding’ of chapter ‘Operation - Enhanced use’.  
MULTI-CHANNEL AUDIO OUT  
(For connection to a multi-channel receiver)  
- SUBW(oofer) - subwoofer connection  
- CENTER - center speaker connection  
- RIGHT/LEFT SURR(ound) - surround speaker connections  
- RIGHT/LEFT - front speaker connections  
MAINS  
MULTICHANNEL AUDIO OUT  
RIGHT SURR. LEFT SURR.  
SUBW  
RIGHT  
LEFT  
CENTER  
VOLTAGE SELECTOR  
220-240V 100-120V  
FILTER  
1
2
3
GND  
STEREO OUT  
DIGITAL AUDIO OUT  
Dolby Digital/  
1
2
DTS/MPEG only  
R
L
(CVBS)  
VIDEO OUT  
( Y/C )  
S-VIDEO  
CR  
CB  
Y
OPT OUT  
DIG OUT  
AUDIO  
DIGITAL AUDIO OUT  
- OPT(ical) OUT - digital audio output connector for  
connection to digital (optical) equipment  
- DIG(ital) OUT - digital audio output connector for  
connection to digital (coaxial) equipment  
STEREO OUT  
- Audio outputs for connection to an amplifier,  
receiver or stereo system  
VIDEO OUT (CVBS)  
- for connection to a TV with CVBS video inputs  
YUV(YCBCR)  
- for connection to a TV with YUV inputs  
S-VIDEO OUT (Y/C)  
- for connection to a TV with S-Video (Y/C) inputs  
Caution: Do not touch the inner pins of the rear  
panel connectors. Electrostatic discharge may  
cause permanent damage to the unit.  
14 FUNCTIONAL OVERVIEW  
Download from Www.Somanuals.com. All Manuals Search And Download.  
01_SACD1000_USA_23811_D1 11-12-2000 16:13 Pagina 18  
Preparation  
Connecting to a Multi-channel  
Audio/(Video) receiver with 6 connectors  
General notes  
- Depending on your amplifier/receiver/Stereo System,  
there are various ways to connect the player. These are  
explained in the section below.  
This SACD player contains a multi-channel decoder. This  
enables playback of SACDs recorded in Multi-channel.  
You only need to select Multi-channel using the Sound  
Mode key.  
- For some connections, settings for digital and/or  
analogue output are required. These settings have to be  
made in the ‘Personal Preferences’ menu which is only  
accessible via your TV screen. In these cases you will  
need to connect the player to the TV as well.  
- Please refer to your amplifier/receiver/Stereo System,  
TV and any other User Manual(s) as necessary to make  
the optimal connections.  
1
2
3
Connect the audio Left and Right outputs for Front  
speaker connection (1) to the corresponding input  
sockets on your receiver using the audio cable  
supplied.  
Connect the audio Left and Right outputs for  
Surround speaker connection (2) to the  
corresponding inputs on your receiver using an  
optional audio cable.  
Connect the audio outputs for Center speaker and  
Subwoofer connection (3) to the corresponding  
inputs on your receiver using an optional audio  
cable.  
Caution: Do not connect the player’s audio  
output to the phono input of your audio system.  
Connecting to audio equipment -  
analogue  
Note: If the subwoofer is equipped with its own amplifier, the  
Subwoofer connection should be connected directly to the  
subwoofer.  
Connecting to an amplifier/receiver  
equipped with two channel analogue  
stereo  
AMPLIFIER  
Connect the audio Left and Right outputs for Front  
speaker connection (1) to the corresponding  
sockets on your amplifier, receiver or stereo system  
using the audio cable supplied.  
AMPLIFIER  
2
3
1
MAINS  
MULTICHANNEL AUDIO OUT  
RIGHT SURR. LEFT SURR.  
RIGHT  
LEFT  
SUBW  
CENTER  
VOLTAGE SELECTOR  
220-240V 100-120V  
FILTER  
1
2
3
GND  
STEREO OUT  
DIGITAL AUDIO OUT  
Dolby Digital/  
1
2
DTS/MPEG only  
1
R
L
(CVBS)  
VIDEO OUT  
(
Y/C  
)
CR  
CB  
Y
S-VIDEO  
OPT OUT  
DIG OUT  
AUDIO  
MAINS  
MULTICHANNEL AUDIO OUT  
RIGHT SURR. LEFT SURR.  
RIGHT  
LEFT  
SUBW  
CENTER  
VOLTAGE SELECTOR  
220-240V 100-120V  
FILTER  
1
2
3
GND  
STEREO OUT  
DIGITAL AUDIO OUT  
Dolby Digital/  
1
2
DTS/MPEG only  
R
L
(CVBS)  
VIDEO OUT  
(
Y/C  
)
CR  
CB  
Y
S-VIDEO  
OPT OUT  
DIG OUT  
AUDIO  
18 PREPARATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
01_SACD1000_USA_23811_D1 11-12-2000 16:13 Pagina 19  
Connecting to an amplifier/receiver  
equipped with Dolby Pro Logic  
Connecting to an Audio/(Video) receiver  
with multi-channel decoder (Dolby Digital,  
MPEG 2 and DTS)  
For an amplifier/receiver with Dolby Surround, you can  
connect your SACD player in the same way as described  
for Dolby Pro Logic.  
Digital Multi-channel sound (not for SACD)  
For this you need a multi-channel A/V receiver that  
supports one or more of the DVD audio formats  
supported by your SACD player (MPEG 2, Dolby Digital  
and DTS). Check the receiver manual and the logos on  
the front of the receiver.  
Dolby Pro Logic sound  
1
Connect the audio Left and Right outputs for Front  
speaker connection (1) to the corresponding inputs  
on the Dolby Pro Logic Audio/Video  
amplifier/receiver using the audio cable supplied.  
Set Analogue Output to Dolby Surround in the  
‘Personal Preferences’ menu.  
1
Connect the player’s digital audio output (optical 4  
or coaxial 5) to the corresponding input on the  
receiver using the digital audio cable (coaxial) is  
supplied. Optical is optional.  
2
If your amplifier/receiver is equipped with a  
Dolby Digital decoder  
AMPLIFIER  
Connect the player as described in the section  
‘Connecting to an Audio/(Video) receiver with multi-  
channel decoder’.  
If you connect the player to a TV equipped with a  
Dolby Pro Logic decoder  
4
5
Connect the player to the TV as described in the  
section ‘Connecting to a TV’.  
MAINS  
MULTICHANNEL AUDIO OUT  
RIGHT SURR. LEFT SURR.  
RIGHT  
LEFT  
SUBW  
CENTER  
VOLTAGE SELECTOR  
220-240V 100-120V  
FILTER  
1
2
3
Connecting to audio equipment -  
digital  
GND  
STEREO OUT  
DIGITAL AUDIO OUT  
Dolby Digital/  
1
2
DTS/MPEG only  
R
L
(CVBS)  
VIDEO OUT  
(
Y/C  
)
CR  
CB  
Y
S-VIDEO  
OPT OUT  
DIG OUT  
AUDIO  
The digital output of the SACD1000 does not provide  
PCM (Pulse Code Modulation) signals. If your  
amplifer/receiver can only decode PCM and not multi-  
channel signals such as Dolby Digital, do not connect  
your SACD player using the digital input. This could  
damage your amplifier and/or speakers.  
Notes:  
- If the audio format of the digital output does not match the  
capabilities of your receiver, the receiver will produce a  
strong, distorted sound. The audio format of the DVD disc in  
play is displayed in the Status Window when changing the  
audio format.  
- 6 Channel Digital Surround Sound via digital connection can  
only be obtained if your receiver is equipped with a Digital  
Multi-channel decoder. If your receiver does not contain a  
decoder, you can make the analogue connections as  
described in the section‘Connecting to a Multi-channel  
Audio/(Video) receiver with 6 connectors’ to obtain 6 Channel  
Digital Surround Sound.  
- SACD Multi-channel sound cannot be obtained via digital  
connection.  
PREPARATION 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
01_SACD1000_USA_23811_D1 11-12-2000 16:13 Pagina 20  
Connecting to a TV  
6 Channel settings - DVD only  
Notes  
Front speaker  
- Depending on your TV, there are various ways to connect  
the player. These are shown in the illustration below.  
- Please refer to your TV, VCR, and any other User Manual(s)  
as necessary to make the optimal connections.  
- Do not connect your SACD-player via your VCR because the  
video quality could be distorted by the copy protection system.  
L (Large) : When the front speakers can reproduce low  
frequency signals below 120Hz  
S (Small) : When the front speakers cannot reproduce  
low frequency signals below 120Hz  
Center Speaker  
L (Large) : When the center speaker can reproduce low  
frequency signals below 120Hz  
S (Small) : When the center speaker cannot reproduce  
low frequency signals below 120Hz  
S-Video (Y/C) connection  
1
Connect the S-VIDEO OUT (Y/C) socket (7) to the  
corresponding socket on the TV using an optional  
S-Video cable.  
Off  
: When the center speaker is not connected  
Surround speakers  
If you wish to receive the sound via your TV,  
connect the STEREO OUT Left and Right output  
sockets (1) to the corresponding sockets on the TV  
using the audio cable supplied.  
L (Large) : When the surround speakers can reproduce  
low frequency signals below 120Hz  
S (Small) : When the surround speakers cannot  
reproduce low frequency signals below 120Hz  
Off  
: When the surround speakers are not  
connected  
Video CVBS connection  
Subwoofer  
1
Connect the VIDEO OUT (CVBS) socket (8) to the  
corresponding socket on the TV using the video  
cable supplied.  
On  
Off  
: When you connect a subwoofer  
: When a subwoofer is not connected  
2
If you wish to receive the sound via your TV,  
connect the STEREO OUT Left and Right output  
sockets (1) to the corresponding sockets on the TV  
using the audio cable supplied.  
Center  
speaker  
Front speaker  
left  
Front speaker  
right  
TV  
1
8
7
Rear speaker  
(left surround)  
Rear speaker  
(right surround)  
MAINS  
MULTICHANNEL AUDIO OUT  
RIGHT SURR. LEFT SURR.  
RIGHT  
LEFT  
SUBW  
CENTER  
VOLTAGE SELECTOR  
220-240V 100-120V  
FILTER  
1
2
3
GND  
STEREO OUT  
DIGITAL AUDIO OUT  
Dolby Digital/  
1
2
DTS/MPEG only  
R
L
(CVBS)  
VIDEO OUT  
(
Y/C  
)
CR  
CB  
Y
OPT OUT  
DIG OUT  
AUDIO  
S-VIDEO  
20 PREPARATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
01_SACD1000_USA_23811_D1 11-12-2000 16:13 Pagina 21  
Delay times - DVD only  
Connecting the power supply  
Your SACD player is set to correctly reproduce  
synchronized Digital Surround Sound in a listening area  
where the surround speakers are about 150cm nearer  
to the listening position than the front speakers and the  
center speaker is in line with the front speakers. To  
adjust for other listening-area arrangements, adapt delay  
times according to the following:  
1
Check if the power voltage as shown on the type  
plate (on the back of the player) corresponds to  
your local power voltage. If not, adjust the voltage  
selector (1) to match with your local power supply.  
Plug the female end of the power cable supplied into  
the Power connector POWER SUPPLY (2) on the  
rear of the player.  
2
3
Plug the male end of the cord into an AC outlet.  
Digital Surround  
Note: When the player is in the STANDBY or OFF position, it  
will still consume some power. If you wish to disconnect your  
player completely from the power supply, pull the plug from  
the AC Outlet.  
Measure the distances in centimeters from the front  
speaker plane and from the surround speaker plane to  
the listening positioning plane.  
Substract the surround distance from the front distance  
and divide by 30. The result is the required Surround  
Channel delay time in milliseconds.  
Caution: Only qualified service personnel should  
remove the cover or attempt to service this  
device.  
If the center speaker is on the front speaker plane, no  
center speaker delay is needed. You can adjust the delay  
time in the “User Preference Settings”. See Personal  
preferences - Sound - Speaker Settings. If, however, it is  
nearer to the listening position, measure the distance in  
centimeters between the front and center speaker  
planes and divide by 30. The result is the required  
Center Channel delay time in milliseconds.  
1
2
V
O
L
T
A
G
E
S
E
L
E
C
T
2
O
2
R
V
0
-2  
4
0
V
M
A
1
IN  
S
0
0
-1  
2
0
Digital Surround Delay  
10  
5
ms ms  
0 ms  
0 ms  
0 ms  
0 ms  
-5 ms  
-10 ms  
12  
10,5  
9
7,5  
6
4,5  
3
Differential  
arrival time  
1,5  
0
Preferred  
0
1,5  
3
4,5  
6
7,5  
9
10,5 12  
Acceptable  
Not recommended  
Distance from front speakers (m)  
Dolby Pro Logic  
If the delay times for Surround Channel and Center  
Channel are set for Digital Surround mode, the delay  
times for Dolby Pro Logic mode will automatically be  
calculated and set.  
Pro Logic Surround Delay  
25 20  
ms ms  
15 ms  
15 ms  
15 ms  
15 ms  
10 ms  
5 ms  
12  
10,5  
9
7,5  
6
4,5  
3
Differential  
arrival time  
1,5  
0
Preferred  
0
1,5  
3
4,5  
6
7,5  
9
10,5 12  
Acceptable  
Not recommended  
Distance from front speakers (m)  
PREPARATION 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
01_SACD1000_USA_23811_D1 11-12-2000 16:14 Pagina 36  
System grounding  
Enhanced use  
Filter switch  
When your system consists of a lot of components,  
occasional disturbance problems (like howling noises)  
may occur. These problems can be solved by grounding  
the system.  
Not all amplifiers/receivers and speakers can handle the  
extended frequency response of SACD. Your SACD is  
equipped with a switchable filter on the rear. The  
factory setting for this filter is 40 KHz, which is safe for  
all systems. If your system can handle the full frequency  
range of SACD (check the relevant manuals or, when in  
doubt, contact your dealer) do the following:  
1
Unscrew the ground connector GND halfway,  
connect an earth wire to the connector and tighten  
the connector again.  
V
O
L
T
A
G
E
S
E
L
E
C
T
2
O
2
R
V
0
-2  
4
0
V
M
A
IN  
S
1
0
0
-1  
2
MAINS  
0
RIGHT  
LEFT  
VOLTAGE SELECTOR  
220-240V 100-120V  
F
1
IL  
T
ER  
FILTER  
2
3
1
2
3
G
N
D
GND  
STEREO OUT  
DIGITAL AUDIO OUT  
Dolby Digital/  
DTS/MPEG only  
R
L
V
OPT OUT  
DIG OUT  
AUDIO  
2
3
Connect the earth wire to the ground connector of  
the next component in the system.  
If ground connectors are available on the other  
components of your system, ground the other  
components in the same way.  
Set the switch to the required output signal.  
Position 1 : 40 kHz - output signal on all speakers is set  
to 40 kHz.  
Position 2 : 50 kHz FRONT/50 kHz OTHERS - output  
signal on front speakers is set to 50 kHz;  
output signal on all other speakers is set to  
40 kHz.  
Position 3 : 50 kHz - output signal on all speakers is set  
to 50 kHz.  
Warning: If you are not sure that your system is  
able to handle audio input signals up to 50 KHz,  
do not change the output signal. You may  
damage your speakers or amplifier/receiver.  
36 OPERATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips DVR VR 540 User Manual
Philips Network Card SJA9480 User Manual
Philips Power Supply LR6PC24C User Manual
Philips Projection Television 64P 9271 User Manual
Philips Video Game Headset SHB6100 User Manual
Pioneer Home Theater System S DV131 User Manual
Pitney Bowes Scale N421 User Manual
Playskool Games 09154 User Manual
ProForm Treadmill 831247452 User Manual
PYLE Audio Drums PTED01 User Manual