Philips Speaker HTL5120 User Manual

For product support, visit  
HTL5120  
User manual  
EN: For further assistance, call the customer support service in your country.  
• To obtain assistance in the U.S.A., Canada, Puerto Rico, or the U.S. Virgin Islands, contact  
Philips Customer Care Center at 1-866-310-0744  
• To obtain assistance in Mexico, contact Philips Customer Care Center at 01 800 839 1989;  
Mexico City: 58 87 97 36  
For Product recycling information, please visit - www.recycle.philips.com  
P&F USA, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
1 Important  
2
2
3
3
4
Important safety instructions  
Care for your product  
Care of the environment  
Help and support  
2 Your SoundBar  
Main unit  
5
5
5
7
Remote control  
Connectors  
3 Connect  
8
8
8
Connect toTV  
Connect digital devices through HDMI  
Connect audio fromTV and other  
devices  
9
4 Use your SoundBar  
Adjust the volume  
Choose your sound  
MP3 player  
10  
10  
10  
11  
11  
12  
12  
Play audio through Bluetooth  
Auto standby  
Apply factory settings  
5 Wall mount your SoundBar  
13  
13  
Wall mount  
6
Product specifications  
14  
7 Troubleshooting  
15  
8 Notice  
16  
16  
16  
Notice of compliance  
Trademarks  
EN  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 Important  
Read and understand all instructions before you  
use your product. If damage is caused by failure  
to follow instructions, the warranty does not  
apply.  
Use only with the cart, stand, tripod,  
bracket or table specified by the  
manufacturer or sold with the apparatus.  
When a cart is used, use caution when  
moving the cart/apparatus combination to  
avoid injury from tip-over.  
Unplug this apparatus during lightning  
storm or when unused for long periods of  
time.  
Important safety instructions  
Read these instructions.  
Keep these instructions.  
Heed all warnings.  
Follow all instructions.  
Do not use this apparatus near water.  
Clean only with dry cloth.  
Do not block any ventilation openings.  
Install in accordance with the  
manufacturer's instructions.  
Do not install near any heat sources  
such as radiators, heat registers, stoves, or  
other apparatus (including amplifiers) that  
produce heat.  
Refer all servicing to qualified service  
personnel. Servicing is required when  
the apparatus has been damaged in any  
way, such as power-supply cord or plug  
is damaged, liquid has been spilled or  
objects have fallen into the apparatus, the  
apparatus has been exposed to rain or  
moisture, does not operate normally, or  
has been dropped.  
Battery usage CAUTION -To prevent  
battery leakage which may result in bodily  
injury, property damage, or damage to the  
unit:  
Install all batteries correctly, + and - as  
marked on the unit.  
Do not mix batteries (old and new or  
carbon and alkaline, etc.).  
Remove batteries when the unit is not  
used for a long time.  
The batteries shall not be exposed to  
excessive heat such as sunshine, fire or  
the like.  
Do not defeat the safety purpose of  
the polarized or grounding-type plug.A  
polarized plug has two blades with one  
wider than the other.A grounding type  
plug has two blades and a third grounding  
prong.The wide blade or the third prong  
are provided for your safety. If the provided  
plug does not fit into your outlet, consult  
an electrician for replacement of the  
obsolete outlet.  
Protect the power cord from being  
walked on or pinched, particularly at plugs,  
convenience receptacles, and the point  
where they exit from the apparatus.  
Only use attachments/accessories  
specified by the manufacturer.  
Perchlorate Material - special handling  
hazardouswaste/perchlorate.  
The product/remote control may contain  
a coin/button type battery, which can be  
swallowed. Keep the battery out of reach  
of children at all times! If swallowed, the  
battery can cause serious injury or death.  
Severe internal burns can occur within two  
hours of ingestion.  
2
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If you suspect that a battery has been  
swallowed or placed inside any part of the  
body, seek immediate medical attention.  
When you change the batteries, always  
keep all new and used batteries out of  
reach of children. Ensure that the battery  
compartment is completely secure after  
you replace the battery.  
This 'bolt of lightning' indicates uninsulated  
material within your unit may cause an electrical  
shock. For the safety of everyone in your  
household, please do not remove product  
covering.  
If the battery compartment cannot be  
completely secured, discontinue use of the  
product. Keep out of reach of children and  
contact the manufacturer.  
Apparatus shall not be exposed to  
dripping or splashing.  
Do not place any sources of danger on  
the apparatus (for example. liquid filled  
objects, lighted candles).  
The 'exclamation point' calls attention to  
features for which you should read the enclosed  
literature closely to prevent operating and  
maintenance problems.  
WARNING:To reduce the risk of fire or  
electric shock, this apparatus should not be  
exposed to rain or moisture and objects filled  
with liquids, such as vases, should not be placed  
on this apparatus.  
This apparatus may contain lead and  
mercury. Dispose according to local, State  
or Federal laws. For disposal or recycling  
information, please contact your local  
authorities. For additional assistance on  
recycling options, please contact www.  
Where the MAINS plug or an appliance  
coupler is used as the disconnect device,  
the disconnect device shall remain readily  
operable.  
Do not place this apparatus on the  
furniture that is capable of being tilted by a  
child and an adult leaning, pulling, standing  
or climbing on it.A falling apparatus can  
cause serious injury or even death.  
This apparatus should not be placed in a  
built-in installation such as a bookcase or  
rack unless proper ventilation is provided.  
Make sure to leave a space of 7.8 inches  
(20cm) or more around this apparatus.  
CAUTION:To prevent electric shock, match  
wide blade of plug to wide slot, fully insert.  
Care for your product  
Use only microfiber cloth to clean the product.  
Care of the environment  
Your product is designed and manufactured  
with high quality materials and components,  
which can be recycled and reused. Please  
visit www.recycle.philips.com for additional  
information on a recycling center in your area.  
Class II equipment symbol  
This symbol indicates that the unit has a double  
insulation system.  
Never dispose of your product with other  
household waste. Please inform yourself about  
the local rules on the separate collection of  
EN  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
electrical and electronic products and batteries.  
The correct disposal of these products helps  
prevent potentially negative consequences on  
the environment and human health.  
The batteries supplied do not contain the heavy  
metals mercury and cadmium. Nevertheless,  
in many areas batteries may not be disposed  
of with your household waste. Please ensure  
you dispose of batteries according to local  
regulations.  
For perchlorate material, special handling may  
perchlorate.  
Help and support  
Philips provides extensive online support.Visit  
download the user manual and the quick  
start guide  
watch video tutorials (available only for  
selected models)  
find answers to frequently answered  
questions (FAQs)  
email us a question  
chat with our support representative.  
Follow the instructions on the website to select  
your language, and then enter your product  
model number.  
Alternatively, you can contact Philips Consumer  
Care in your country. Before you contact  
Philips, note down the model number and  
serial number of your product.You can find this  
information on the back or bottom of your  
product.  
4
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTICAL: Lights up when you switch  
to optical input source.  
2 Your SoundBar  
AUX/Bluetooth: Lights up when you  
switch to analog input source. Blinks  
when you switch to Bluetooth mode.  
COAXIAL: Lights up when you switch  
to coaxial input source.  
Congratulations on your purchase, and  
welcome to Philips!To fully benefit from  
the support that Philips offers, register your  
c Volume indicator/V. SURR indicator  
When you change volume, volume  
indicators light up to indicate the  
volume level.  
Main unit  
Lights up when you selectVirtual  
Surround sound.  
This section includes an overview of the main  
unit.  
d Volume indicator/MUSIC iLINK indicator  
When you change volume, volume  
indicators light up to indicate the  
volume level.  
Lights up when you select MUSIC  
iLINK as the input source.  
Bluetooth  
Remote control  
This section includes an overview of the  
remote control.  
a
(Standby-On/Standby indicator)  
Switch the SoundBar on or to standby.  
When the SoundBar is in standby, the  
standby indicator turns red.  
b Volume indicator/Source indicators  
When you change volume, volume  
indicators light up to indicate the volume  
level.  
Source indicator lights up when a source  
is selected.  
HDMI ARC: Lights up when you select  
HDMI ARC as the input source.  
HDMI 1: Lights up when you select  
HDMI IN 1 as the input source. Blinks  
for five seconds when you play Dolby  
audio.  
HDMI 2: Lights up when you select  
HDMI IN 2 as the input source. Blinks  
for five seconds when you play DTS  
audio.  
EN  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Switch your audio source to the coaxial  
connection.  
1
f MUSIC iLINK  
2
3
Switch your audio source to the MUSIC  
iLINK connection.  
17  
4
5
6
g AUTOVOLUME ON/OFF  
Turn auto volume or or off.  
16  
15  
Bluetooth  
h AUDIO SYNC +/-  
Increase or decrease audio delay.  
i +/- (Volume)  
Increase or decrease volume.  
7
14  
13  
j TREBLE +/-  
Increase or decrease treble.  
8
9
k BASS +/-  
Increase or decrease bass.  
10  
11  
l V.SURR  
Toggle between stereo and virtual  
surround sound.  
m
(Mute)  
Mute or restore volume.  
12  
n NIGHT MODE ON/OFF  
Turn night mode on or off.  
o Bluetooth  
Switch to Bluetooth mode.  
a
(Standby-On)  
p AUX  
Switch the SoundBar on or to standby.  
When EasyLink is enabled, press  
and hold for at least three seconds  
to switch all connected HDMI CEC  
compliant devices to standby.  
Switch your audio source to the AUX  
connection.  
q HDMI ARC  
Switch your source to HDMI ARC  
connection. HDMI ARC can only be  
selected if you connect your SoundBar  
to an HDMI ARC compliantTV through  
HDMI ARC.  
b HDMI 1  
Switch your source to the HDMI IN 1  
connection.  
c HDMI 2  
Switch your source to the HDMI IN 2  
connection.  
d OPTICAL  
Switch your audio source to the optical  
connection.  
e COAX  
6
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
e AUDIO IN-AUX  
Connectors  
Connect to an analog audio output on the  
TV or an analog device.  
This section includes an overview of the  
connectors available on your SoundBar.  
f DIGITAL IN-COAXIAL  
Connect to a coaxial audio output on the  
TV or a digital device.  
Rear connectors  
g DIGITAL IN-OPTICAL  
Connect to an optical audio output on the  
TV or a digital device.  
a MUSIC iLINK  
Audio input from an MP3 player.  
Bottom connectors  
g
6
1
5
4
2
3
a HDMI IN 1  
Connect to the HDMI output on a digital  
device.  
b HDMI IN 2  
Connect to the HDMI output on a digital  
device.  
c TOTV-HDMI OUT (ARC)  
Connect to the HDMI input on theTV.  
d AC MAINS~  
Connect to the power supply.  
EN  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
The HDMI ARC connector on theTV  
might be labeled differently. For details,  
see theTV user manual.  
3 Connect  
2 On yourTV, turn on HDMI-CEC  
operations. For details, see theTV user  
manual.  
This section helps you connect your SoundBar  
to aTV and other devices.  
For information about the basic connections of  
your SoundBar and accessories, see the quick  
start guide.  
Note  
SoundBar. (see 'Connect audio fromTV and other  
devices' on page 9)  
If yourTV has a DVI connector, you can use an HDMI/  
DVI adapter to connect toTV. However, some of the  
features may not be available.  
Note  
For identification and supply ratings, refer to the type  
plate at the back or bottom of the product.  
Before you make or change any connections, make sure  
that all devices are disconnected from the power outlet.  
Connect digital devices  
through HDMI  
Connect toTV  
Connect your SoundBar to aTV.You can listen  
to audio fromTV programs through your  
SoundBar. Use the best quality connection  
available on your SoundBar andTV.  
Connect a digital device such as a set-top box,  
DVD/Blu-ray player, or games console to your  
SoundBar through a single HDMI connection.  
When you connect the devices in this way and  
play a file or game, the  
Connect toTV through HDMI (ARC)  
video is automatically displayed on your  
TV, and  
Your SoundBar supports HDMI with Audio  
Return Channel (ARC). If yourTV is HDMI ARC  
compliant, you can hear theTV audio through  
your SoundBar by using a single HDMI cable.  
audio is automatically played on your  
SoundBar.  
1 Using a High Speed HDMI cable, connect  
the HDMI OUT connector on your digital  
device to the HDMI IN 1/2 on your  
SoundBar.  
TV  
2 Connect your SoundBar toTV through  
HDMI OUT (ARC).  
If theTV is not HDMI CEC compliant,  
select the correct video input on your  
TV.  
3 On the connected device, turn on HDMI-  
CEC operations. For details, see the user  
manual of the device.  
1 Using a High Speed HDMI cable, connect  
the HDMI OUT (ARC) connector on your  
SoundBar to the HDMI ARC connector  
on theTV.  
8
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 Using a coaxial cable, connect the  
COAXIAL connector on your SoundBar  
to the COAXIAL/DIGITAL OUT  
Connect audio fromTV and  
other devices  
connector on theTV or other device.  
The digital coaxial connector might be  
labeled DIGITAL AUDIO OUT.  
Play audio fromTV or other devices through  
your Soundbar speakers.  
Use the best quality connection available on  
yourTV, Soundbar, and other devices.  
Option 3: Connect audio through  
analog audio cables  
Note  
Basic quality audio  
When your Soundbar andTV are connected through  
HDMI ARC, an audio connection is not required.  
1 Using an analog cable, connect the AUX  
connectors on your SoundBar to the  
AUDIO OUT connectors on theTV or  
other device.  
Option 1: Connect audio through a  
digital optical cable  
DVD  
Best quality audio  
TV  
1 Using an optical cable, connect the  
OPTICAL connector on your SoundBar to  
the OPTICAL OUT connector on theTV  
or other device.  
The digital optical connector might be  
labeled SPDIF or SPDIF OUT.  
Option 2: Connect audio through a  
digital coaxial cable  
Good quality audio  
EN  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Surround sound mode  
4 Use your  
SoundBar  
Experience an immersive audio experience with  
surround sound modes.  
1 Press V.SURR repeatedly to switch  
surround mode on or off.  
This section helps you use the SoundBar to play  
audio from connected devices.  
» When surround mode is on, the  
V.SURR indicator on the main unit  
lights up. Creates a surround listening  
experience.  
Before you start  
Make the necessary connections described  
in the quick start guide and the user  
manual.  
» When the V.SURR indicator on the  
main unit turns off, two-channel stereo  
sound is on, ideal for listening to music.  
Switch the SoundBar to the correct source  
for other devices.  
Equalizer  
Adjust the volume  
Change the high frequency (treble) and low  
frequency (bass) settings of the SoundBar.  
1 Press +/- (Volume) to increase or decrease  
1 Press TREBLE +/- or BASS +/- to change  
a volume level.  
the treble or bass level.  
To mute sound, press (Mute).  
To restore the sound, press (Mute)  
again or press +/- (Volume).  
Treble/bass indicator  
When you change the treble or bass  
level, all the indicators on the main  
unit blink one by one. If the treble or  
bass level is set to the minimum, all the  
indicators turn off.  
Volume indicator  
• When you change volume, one or multiple  
Volume indicator (up to 8 indicators) on  
the main unit light up to indicate a volume  
level.The more indicators light up, the  
higher the volume level is.  
Auto volume  
Turn the auto volume on to keep the volume  
constant when you switch to a different source.  
0
60  
1 Press AUTOVOLUME ON/OFF to turn  
auto volume on or off.  
» When auto volume is turned on or off,  
V.SURR indicator blinks once.  
If you do not press the volume key for five  
seconds, the volume indicators light off, and  
the current source indicator and the sound  
mode indicator light up.  
Synchronize picture and sound  
If the audio and video are not synchronized,  
delay the audio to match the video.  
Choose your sound  
1 Press AUDIO SYNC +/- to synchronize  
the audio with the video.  
This section helps you choose the ideal sound  
for your video or music.  
10 EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The operational range between the  
SoundBar and a Bluetooth device is  
approximately 10 meters (30 feet).  
Night mode  
For quiet listening, decrease the volume of loud  
sounds when audio is played. Night mode is  
only available for Dolby Digital soundtracks.  
1 Press Bluetooth on the remote control to  
switch the SoundBar to Bluetooth mode.  
» The AUX/Bluetooth indicator blinks at  
a fast rate.  
1 Press NIGHT MODE ON/OFF to turn  
night mode on or off.  
» When night mode is turned on or off,  
V.SURR indicator blinks once.  
2 On the Bluetooth device, switch on  
Bluetooth, search for and select Philips  
HTL5120 to start connection (see the  
user manual of the Bluetooth device on  
how to enable Bluetooth).  
Note  
If auto volume is set to turned on, you cannot enable  
the night mode.  
When prompted for a password, enter  
"0000".  
» During connection, the indicator blinks  
at a lower rate.  
3 Wait until you hear a beep sound from the  
SoundBar.  
MP3 player  
» When the Bluetooth connection  
succeeds, and the AUX/Bluetooth  
indicator lights up.  
Connect your MP3 player to play your audio  
files or music.  
What you need  
» If the connection fails, the  
AUX/Bluetooth indicator blinks  
continually at a lower rate.  
An MP3 player.  
A 3.5mm stereo audio cable.  
1 Using the 3.5mm stereo audio cable,  
connect the MP3 player to the MUSIC  
iLINK connector on your SoundBar.  
4 Select and play audio files or music on  
your Bluetooth device.  
During play, if a call is coming, music  
play is paused. Play resumes when the  
call ends.  
2 Press MUSIC iLINK.  
3 Press the buttons on the MP3 player to  
select and play audio files or music.  
5 To exit Bluetooth, select other source.  
When your switch back to Bluetooth  
mode, Bluetooth connection remains  
active.  
Play audio through Bluetooth  
Through Bluetooth, connect the SoundBar with  
your Bluetooth device (such as an iPad, iPhone,  
iPod touch,Android phone, or laptop), and then  
you can listen to the audio files stored on the  
device through your SoundBar speakers.  
What you need  
Note  
The music streaming may be interrupted by obstacles  
between the device and SoundBar, such as wall, metallic  
casing that covers the device, or other devices nearby  
that operate in the same frequency.  
If you want to connect your SoundBar with another  
Bluetooth device, disable the currently connected  
Bluetooth device.  
A Bluetooth device which supports  
Bluetooth profile A2DP, and with Bluetooth  
version as 2.1 + EDR.  
Philips does not guarantee 100% compatibility with all  
Bluetooth devices.  
EN 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Auto standby  
When playing media from a connected device,  
the SoundBar automatically switches to standby  
if:  
no source button is pressed for 30  
minutes, and  
no audio/video playback is detected from a  
connected device.  
Apply factory settings  
You can reset your SoundBar to the default  
settings programmed at the factory.  
1 Press TREBLE+, VOL-, and BASS+ within  
three seconds.  
» When the factory settings restore is  
complete, the SoundBar automatically  
switches off and restarts.  
12 EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5 Wall mount  
your SoundBar  
Before you mount your SoundBar on the wall,  
read all safety precautions.  
Wall mount  
Note  
Koninklijke Philips Electronics N.V. bears no  
responsibility for improper wall mounting that results  
in accident, injury or damage. If you have any query,  
contact Philips Consumer Care in your country.  
Secure the wall mount to a wall that can support the  
combined weight of the product and the wall mount.  
Before wall mount, you need not remove the four  
rubber feet at the bottom of the soundbar, otherwise  
the rubber feet cannot be fixed back.  
Screw length/diameter  
Depend on the type of wall mounting this wall  
mount bracket, make sure that you use screws  
of a suitable length and diameter.  
3 - 3.5mm  
> 25mm  
For information about how to wall your  
SoundBar, see the wall mount guide.  
EN 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speaker impedance:  
6 Product  
specifications  
Woofer: 3 ohm  
tweeter: 12 ohm  
Speaker drivers: 2 x 102 mm (4") woofer  
+ 2 x 25.4 mm (1") tweeter  
Dimensions (WxHxD):  
1010 x 81 x 154 mm  
Weight: 3.9 kg  
Note  
Specifications and design are subject to change without  
notice.  
Wall mount  
Dimensions (WxHxD): 40 x 100 x 26.5  
mm  
Weight: 0.1 kg/each  
Amplifier  
FTC total output power: 42W  
Remote control batteries  
Woofer L + Woofer R: 32W ( 1%  
THD, 3ohm, 180Hz-6KHz )  
2 x AAA-R03-1.5V  
Tweeter L +Tweeter R: 10W ( 1%  
THD, 12ohm, 7KHz-20KHz)  
RMS total output power:  
120W RMS (+/- 0.5 dB, 30%THD)  
96W RMS (+/- 0.5 dB, 10%THD)  
Frequency response: 20 Hz-20 kHz /  
±3 dB  
Signal-to-noise ratio: > 65 dB (CCIR) /  
(A-weighted)  
Input sensitivity:  
AUX: 800 mV  
Music iLink: 550 mV  
Audio  
S/PDIF Digital audio input:  
Coaxial: IEC 60958-3  
Optical:TOSLINK  
Bluetooth  
Bluetooth profiles:A2DP  
Bluetooth version: 2.1 + EDR  
Main unit  
Power supply: 110-240V~, 50-60 Hz  
Power consumption: 40 W  
Standby power consumption: ≤ 0.5 W  
14 EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bluetooth  
7 Troubleshooting  
A device cannot connect with the SoundBar.  
The device does not support the  
compatible profiles required for the  
SoundBar.  
Warning  
You have not enabled the Bluetooth  
function of the device. See the user manual  
of the device on how to enable the  
function.  
The device is not correctly connected.  
audio through Bluetooth' on page 11)  
The SoundBar is already connected with  
another Bluetooth device. Disconnect the  
connected device, then try again.  
Risk of electric shock. Never remove the casing of the  
product.  
To keep the warranty valid, never try to repair  
the product yourself.  
If you have problems using this product, check  
the following points before you request service.  
If you still have a problem, get support at www.  
philips.com/support.  
Quality of audio play from a connected  
Bluetooth device is poor.  
Main unit  
The Bluetooth reception is poor. Move the  
device closer to the SoundBar, or remove  
any obstacle between the device and the  
SoundBar.  
The buttons on the SoundBar do not work.  
Disconnect the SoundBar from the power  
supply for a few minutes, then reconnect.  
The connected Bluetooth device connects and  
disconnects constantly.  
Sound  
The Bluetooth reception is poor. Move the  
device closer to the SoundBar, or remove  
any obstacle between the device and the  
SoundBar.  
Turn off Wi-Fi function on the Bluetooth  
device to avoid interference.  
For some Bluetooth, the Bluetooth  
connection can be deactivated  
automatically to save power.This does not  
indicate any malfunction of the SoundBar.  
No sound from SoundBar speakers.  
Connect the audio cable from your  
SoundBar to yourTV or other devices.  
However, you do not need a separate  
audio connection when:  
the SoundBar andTV are connected  
through HDMI ARC connection, or  
a device is connected to the HDMI IN  
connector on your SoundBar.  
(see 'Apply factory settings' on page 12).  
On the remote control, select the correct  
audio input.  
Make sure that the SoundBar is not muted.  
Distorted sound or echo.  
If you play audio from theTV through the  
SoundBar, make sure that theTV is muted.  
Audio and video are not synchronized.  
Press AUDIO SYNC +/- to synchronize  
the audio with the video.  
EN 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC Radiation Exposure Statement:This  
equipment complies with FCC radiation  
exposure limits set forth for an uncontrolled  
environment.This equipment should be installed  
and operated with a minimum distance of  
20cm between the radiator and your body.  
This transmitter must not be co-located or  
operated in conjunction with any other antenna  
or transmitter.  
Warning: Changes or modifications made to  
this equipment not expressly approved by  
Philips may void the FCC authorization to  
operate this equipment.  
Model number: PHILIPS HTL5120/F7  
Trade Name: Philips  
Responsible Party:P&F USA, Inc. PO Box 2248  
Alpharetta, GA 30023-2248; 1-866-310-0744  
Canada:  
This device complies with Industry Canada  
licence-exempt RSS standard(s). Operation is  
subject to the followingTwo conditions: (1) this  
device may not cause harmful interference, and  
(2) this device must accept any interference  
received, including interference that may cause  
undesired operation.  
8 Notice  
This section contains the legal and trademark  
notices.  
Notice of compliance  
This set complies with the FCC rules, Part 15  
and with 21 CFR 1040.10. Operation is subject  
to the following two conditions:  
a This device may not cause harmful  
interference, and  
b This device must accept any interference  
received, including interference that may  
cause undesired operation.  
FCC rules  
This equipment has been tested and found  
to comply with the limits for a Class B digital  
device, pursuant to part 15 of the FCC Rules.  
These limits are designed to provide reasonable  
protection against harmful interference in a  
residential installation.This equipment generates,  
uses and can radiate radio frequency energy  
and, if not installed and used in accordance  
with the instruction manual, may cause harmful  
interference to radio communications.  
However, there is no guarantee that  
This Class B digital apparatus complies with  
Canadian ICES-003.  
Trademarks  
interference will not occur in a particular  
installation. If this equipment does cause harmful  
interference to radio or television reception,  
which can be determined by turning the  
equipment off and on, the user is encouraged  
to try to correct the interference by one or  
more of the following measures:  
Manufactured under license under U.S.  
Patent Nos: 5,956,674; 5,974,380; 6,487,535  
& other U.S. and worldwide patents issued  
& pending. DTS, the Symbol, & DTS and the  
Symbol together are registered trademarks  
& DTS Digital Surround and the DTS logos  
are trademarks of DTS, Inc. Product includes  
software. DTS, Inc.All Rights Reserved.  
Relocate the receiving antenna.  
Increase the separation between  
equipment and receiver.  
Connect the equipment into an outlet on  
a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced  
radio/TV technician for help.  
Manufactured under license from Dolby  
Laboratories. Dolby and the double-D symbol  
are trademarks of Dolby Laboratories.  
16 EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Bluetooth® word mark and logos are  
registered trademarks owned by Bluetooth  
SIG, Inc. and any use of such marks by Philips is  
under license.  
The terms HDMI and HDMI High-Definition  
Multimedia Interface, and the HDMI Logo are  
trademarks or registered trademarks of HDMI  
Licensing LLC in the United States and other  
countries.  
EN 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ONE (1) YEAR LIMITED WARRANTY  
WARRANTY COVERAGE:  
This warranty obligation is limited to the terms set forth  
below.  
or (d) if any serial number has been removed or defaced,  
or (e) product, accessories or consumables sold “AS IS”  
without warranty of any kind by including refurbished Philips  
product sold “AS IS” by some retailers.  
WHO IS COVERED:  
This product is warranted to the original purchaser or the per-  
son receiving the product as a gift against defects in materials and  
workmanship as based on the date of original purchase  
(“Warranty Period”) from an Authorized Dealer. The original  
sales receipt showing the product name and the purchase date  
from an authorized retailer is considered such proof.  
This Limited Warranty does not cover:  
Shipping charges to return defective product.  
Labor charges for installation or setup of the product, adjust-  
ment of customer controls on the product, and installation or  
repair of antenna/signal source systems outside of the product.  
Product repair and/or part replacement because of improper  
installation or maintenance, connections to improper voltage  
supply, power line surge, lightning damage, retained images or  
screen markings resulting from viewing fixed stationary con-  
tent for extended periods, product cosmetic appearance items  
due to normal wear and tear, unauthorized repair or other  
cause not within the control of the company.  
WHAT IS COVERED:  
This warranty covers new products if a defect in material  
or workmanship occurs and a valid claim is received within  
the Warranty Period. At its option, the company will either (1)  
repair the product at no charge, using new or refurbished  
replacement parts, or (2) exchange the product with a product  
that is new or which has been manufactured from new, or ser-  
viceable used parts and is at least functionally equivalent or most  
comparable to the original product in current inventory,  
or (3) refund the original purchase price of the product.  
The company warrants replacement products or parts provided  
under this warranty against defects in materials and workmanship  
from the date of the replacement or repair for ninety (90) days  
or for the remaining portion of the original product’s warranty,  
whichever provides longer coverage for you. When a product or  
part is exchanged, any replacement item becomes your property  
and the replaced item becomes the company property. When a  
refund is given, your product becomes the company property.  
Note: Any product sold and identified as refurbished or  
renewed carries a ninety (90) day limited warranty.  
Damage or claims for products not being available for use, or  
for lost data or lost software.  
Damage from mishandled shipments or transit accidents when  
returning product.  
A product that requires modification or adaptation to enable  
it to operate in any country other than the country for which  
it was designed, manufactured, approved and/or authorized, or  
repair of products damaged by these modifications.  
A product used for commercial or institutional purposes  
(including but not limited to rental purposes).  
Product lost in shipment and no signature verification receipt  
can be provided.  
Failure to operate per Owner’s Manual.  
TO OBTAIN ASSISTANCE IN THE U.S.A., CANADA,  
PUERTO RICO, OR U.S. VIRGIN ISLANDS…  
Contact Customer Care Center at:  
Replacement product can only be sent if all warranty  
requirements are met. Failure to follow all requirements  
can result in delay.  
1-866-310-0744  
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS  
WARRANTY IS THE EXCLUSIVE REMEDY FOR THE CON-  
SUMER. PHILIPS SHALL NOT BE LIABLE FOR ANY INCIDEN-  
TAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF  
ANY EXPRESS OR IMPLIED WARRANTY ON THIS PROD-  
UCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE  
LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR  
FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT  
IS LIMITED IN DURATION TO THE DURATION OF THIS  
WARRANTY.  
WHAT IS NOT COVERED - EXCLUSIONS AND LIMI-  
TATIONS:  
This Limited Warranty applies only to the new products that  
can be identified by the trademark, trade name, or logo affixed  
to it. This Limited Warranty does not apply to any non-Philips  
hardware product or any software, even if packaged or sold  
with the product. Non-Philips manufacturers, suppliers, or  
publishers may provide a separate warranty for their own  
products packaged with the bundled product.  
The company is not liable for any damage to or loss of any ,  
programs data, or other information stored on any media  
contained within the product, or any non-Philips product or part  
not covered by this warranty. Recovery or reinstallation of  
programs, data or other information is not covered under this  
Limited Warranty.  
Some states do not allow the exclusions or limitation of inciden-  
tal or consequential damages, or allow limitations on how long an  
implied warranty lasts, so the above limitations or exclusions may  
not apply to you.  
This warranty does not apply (a) to damage caused by accident,  
abuse, misuse, neglect, misapplication, or non-Philips product, (b)  
to damage caused by service performed by anyone other than  
an Authorized Service Location, (c) to a product or  
a part that has been modified without written permission,  
This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province.  
P&F USA Inc. PO Box 2248 Alpharetta, GA 30023-2248  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P&F USA, Inc.  
PO Box 2248 Alpharetta, GA 30023-2248  
Specifications are subject to change without notice  
© 2013 Koninklijke Philips Electronics N.V.  
All rights reserved.  
HTL5120_F7_UM_V1.0  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Patton electronic Universal Remote 10100 User Manual
Pentax Security Camera PC 30 User Manual
Philips Portable DVD Player PD7030 User Manual
Philips TV DVD Combo 20MDRF20 User Manual
Philips VCR VRX463AT User Manual
Philips Work Light T8 U Bent User Manual
Pioneer Car Stereo System P5800MP User Manual
Pioneer Flat Panel Television PRO 1140HD User Manual
Porter Cable Router 5043 User Manual
Procom Electric Heater MN200HBA User Manual