User guide
ProScreen PXG20
Multimedia projector
)
Philips
Creative Display
Solutions
Download from Www.Somanuals.com. All Manuals Search And Download.
1. IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate
your projector. Save these instructions for future
S
reference.
Electric energy can perform many useful functions.
This projector has been engineered and manufactured to meet
applicable safety standards. IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order
not to defeat the safeguards incorporated into this projector,
observe the following basic rules for its installation, use and
servicing.
12. As a safety feature, this projector is equipped with
powercord with a 3-pin grounded plug (for USA-versions
only) or a 2-pin grounded plug (for European versions only).
The 3-pin/2-pin grounded plug will fit only into a grounding
type power outlet. If the plug does not fit, use an adapter
that is properly grounded or have an electrician install a
grounded type outlet. Do not attempt to modify this AC
plug.
13. For added protection of the projector during a lightning
storm, or when it is left unattended or not in use for long
periods of time, unplug it from the wall outlet and
disconnect any cable systems. This will prevent damage to
the projector due to lightning and power-line surges.
14. Do not overload wall outlets and extension cords with too
many products, because this can cause a fire or electric
shock.
15. Never push objects of any kind into the projector through
cabinet slots as they may touch dangerous voltage points
or short cut parts, which could result in a fire or electric
shock.
16. Do not attempt to service the projector yourself other than
maintenance issues presented in chapter ‘ADDITIONAL
INFORMATION/Maintenance’. Opening or removing covers
may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
1. Unplug the projector from the wall outlet before cleaning or
lamp replacement.
2. Do not use liquid cleaners or aerosol cleaners. Use a soft
dry cloth to clean the projector unit. If the unit is very dirty,
wet a cloth with neutral detergent, squeeze it tight, wipe
the unit with it, and finish by wiping with a dry cloth.
Do not use a chemical duster or polisher-cleaner because it
can adversely affect the unit and peel the paint.
3. Do not use attachments not recommended by PHILIPS, as
they may cause hazards.
4. Do not use the projector near water- for example, near a
bathtub, washbowl, kitchen sink, or laundry tub, in a wet
basement, near a swimming pool, etc. Never spill liquid
into the projector.
5. Do not place the projector on an unstable cart, stand, or
table. The projector may fall, which may cause serious
injury to a child or an adult and/or serious damage to the
unit. Use only with a cart or stand recommended by its
manufacturer as being suitable for use with a projector.
6. Ceiling, wall or shelf mounting should be done with a
mounting kit approved by the manufacturer for use with a
projector and should follow the manufacturer’s instructions.
7. Projector equipment and cart combinations should be
moved with care. Quick stops, excessive force, and uneven
surfaces may cause the equipment and cart combination to
overturn.
8. Slots and openings in the sides and bottom of the cabinet
are provided for ventilation. To ensure reliable operation of
the projector and to protect it from overheating, these
openings must not be blocked or covered. These openings
should never be covered with cloth or other material. The
bottom opening should not be blocked by placing the
projector on a bed, sofa, rug, or other similar surface. The
projector should not be placed near or over a radiator or
heating vent. The projector should not be placed in a built-
in installation such as a bookcase unless proper ventilation
is provided.
17. Unplug the projector from the wall outlet and refer
servicing to qualified service personnel under the following
conditions:
A. When the powercord or plug is damaged or frayed.
B. If liquid has been spilled into the projector.
C. If the projector has been exposed to rain or water.
D. If the projector does not operate normally when you
follow the operating instructions. Adjust only those
controls that are covered by the operating instructions;
improper adjustment of other controls may cause
damage and will often require extensive work by a
qualified technician to restore the projector to normal
operation.
E. If the projector has been dropped or the cabinet has
been damaged.
F. When the projector exhibits a distinct change in
performance – (this indicates a need for service).
18. Upon completion of any service or repairs to the projector,
ask the service technician to perform a routine safety check
to check that the projector is in safe operating condition.
19. When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original parts. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
20. It is recommended to clean the air filter after every 100
lamp hours. The projector may become too hot if the filter
is not cleaned when required.
9. The projector should be operated only from the type of
power source indicated on the back of the projector or in
the specifications and with the appropriate powercord. If
you are not sure of the type of power supplied to your
business or the right type of powercord, consult your
projector dealer or local power company.
10. Do not allow anything to rest on the powercord. Do not
place the projector where the cord will be walked on.
21. If the lens becomes dirty or smudged, clean it with a clean,
11. Follow all warnings and instructions marked on the
dampened cloth. Never touch the lens with your fingers.
projector.
22. Do not look directly into the aperture and lens while
operating the projector as this may damage your eyes.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
2. INTRODUCTION
TABLE OF CONTENTS
INTRODUCTION
The supplied CD-ROM contains operating instructions in
English, German, French, Spanish, Portuguese, Italian and
Dutch. Carefully read through the operation instructions
before operating the LCD-projector.
1. IMPORTANT SAFEGUARDS .............................................1
2. INTRODUCTION.................................................................2
3. THINGS YOU SHOULD KNOW ........................................3
4. PROJECTOR FEATURES....................................................5
PACKAGING CONTENTS
Please confirm that the following items are packed in the
projector box. They are provided to help you use or set up your
projector.
5. FUNCTIONAL OVERVIEW.................................................7
Controls ...............................................................................7
Remote Control ...................................................................8
Connections.........................................................................8
6. SET UP...........................................................................9-10
Positioning the projector and screen...................................9
Power supply.......................................................................9
Adjusting the vertical and horizontal angle of the projector9
Lens adjustment................................................................10
Moving the projector .........................................................10
Inserting the batteries in remote control...........................10
• ProScreen PXG 20
• Lens cap
• powercord (2x); USA version plus Continental Europe version
• Computer audio cable
• Computer VGA cable
• DIN-D-sub RS-232C cable
• RCA Audio Video Cable
• BNC-RCA adapters (3x)
• S-Video Cable
• Scart - RCA adapter
• Remote control plus AA size batteries (3x)
• USB mouse receiver
• User guide; CD-ROM plus Quick Reference Card
• Extra air filter
• Registration card
7. INSTALLATION .......................................................... 11-14
Video/computer cables and adapter..................................11
Connecting to a computer.................................................12
Connecting to video equipment ........................................12
Connecting to audio equipment ........................................14
Connecting to remote control mouse receiver .................14
8. OPERATION................................................................ 15-21
Preparation.........................................................................15
Using the remote control ..................................................15
Graphical User Interface....................................................16
Language selection............................................................16
Picture control ..............................................................17-20
Data mode / Video mode input signal ...............................17
Data mode display.............................................................18
Data mode / Video mode display ......................................19
Audio control .....................................................................20
Personal Preferences ........................................................21
9. OTHER SETTING.........................................................22-27
Reverse/Invert image function ..........................................22
Digital freeze (D-Freeze) ....................................................22
Digital image magnification (D-Zoom) ...............................23
Digital video effect (V-Effect).............................................23
Picture display mode (V-Format)...................................23-24
AV Mute function...............................................................23
Turning off the On-Screen Display ....................................24
On-Screen Display override function.................................25
Economy mode .................................................................25
Monitor out / RS232C off function....................................25
Automatic power shutoff function ....................................25
Password...........................................................................25
Selecting the keylock level................................................26
Checking the lamp usage time..........................................26
Checking the input signal ..................................................26
Setting a background image..............................................26
Selecting a startup image..................................................27
Status function ..................................................................27
10. MENU TREE .....................................................................28
11. ADDITIONAL INFORMATION.................................... 29-31
Connecting RS-232C Port..................................................29
Maintenance.................................................................29-31
12. TROUBLESHOOTING.......................................................32
ILLUSTRATIONS ................................................................4
2
Download from Www.Somanuals.com. All Manuals Search And Download.
3. THINGS YOU SHOULD KNOW
Note:
This equipment has been tested to comply with the limits for a
class A digital device in accordance with Part 15 of the FCC
Rules as well as the European CE marking.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated
in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the user’s guide, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
– Reorientate or relocate the receiving antenna.
– Increase the distance between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for
help.
FCC WARNING:
To assure continued compliance, use only the provided
grounded power supply cord and shielded interface cables
when connecting this device to a computer. Also, any
unauthorized changes or modifications to this equipment could
void the user’s authority to operate this device.
Note:
SAVE ENERGY! To save energy, please put the projector in the
STANDBY position if you are not going to use the projector for
more than 15 minutes.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
(
≤
%
&
* ^
£
™
Lamp
Temp.
)
Power ON
A/V Mute
)
1
$
Volume
Standby
/ OFF
¡
Lens
Menu
2
3
#
@
Data 1
Data 2
V-Format
V-Effect
D-Freeze
D- Zoom
™
4
5
6
!
Video
£
0
9
Auto sync
OK
7 8
§
A
fig. 1
∞
C
B
1
@
!
Computer - RGB / Component inputs
2
Data 1 in (15pin)
Data 2 in
Audio1
Audio2
D
E
Data 1 in (BNC)
R (Pr)
3
M
15pin
BNC
G/G sync (Y)
B (Pb)
HD (C sync)
VD
Menu
Menu
APPARATEN SKALL
ANSLUTAS TILL
JODAT UTTAG.
Audio in
Video in
Data out
Audio out
4
5
L
K
F
G
L
R
110-120V / 220-240V~
RS-232C
S-Video in
D-Zoom
Auto sync
0
9
8
OK
Input
Lens
A/V Mute
6
7
I
H
J
fig. 2
fig. 3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. PROJECTOR FEATURES
1. ADVANCED COMPATIBILITY WITH HIGH-END
WORKSTATIONS AND PC’s
9. EASY-TO-USE GRAPHICAL USER INTERFACE (GUI)
A multi-colour, icon based menu system allows for simple
image adjustments. (Page 16)
Compatible with up to 200 Hz vertical refresh rate, Sync on
Green and Composite Sync signals for use with a wide
variety of high-end PC’s and Workstations. (Page 12)
10. USER-FRIENDLY DESIGN
The two-colour design along with an intuitive Graphical
User Interface (GUI) makes this projector very easy to set
up and adjust.
2. FOR USE WITH DTV*
Allows projection of DTV images and 16:9 wide-screen
images when connected to a DTV decoder or similar video
systems. (Page 13)
11. AUTO SYNC TECHNOLOGY FOR AUTOMATIC IMAGE
PERFECTION
3. BNC TERMINALS FOR COMPONENT AND RGB INPUT
Equipped with BNC terminals for connection to a DTV
decoder, DVD player and similar video systems for higher
quality images. An RCA adapter can also be used with the
BNC terminals. (Page 12, 13)
Automatically makes any necessary adjustments for
perfectly synced computer images. (Page 18)
12. INTELLIGENT COMPRESSION AND EXPANSION
By using intelligent resizing technology, this projector can
display higher and lower resolution images in detail without
compromising quality.
4. 3-D Y/C DIGITAL COMB FILTER
Provides high quality images with minimal dot crawl and
cross colour noise.
13. XGA RESOLUTION FOR HIGH RESOLUTION
PRESENTATIONS
5. 3-D DIGITAL UNIFORMITY
With XGA (1,024 x 768) resolution, this projector can
display very detailed presentation information.
Equipped with new 3D digital uniformity technology for a
clearer, more uniform image.
14. UXGA COMPATIBLE
6. POWER ZOOM AND FOCUS FUNCTION
Features a 130% power zoom function that allows you to
easily adjust the screen size with the remote control. Use
these functions when adjusting the projection distance to
achieve a 102 to 762 cm (40 to 300 inches) screen size.
(Page 10)
UXGA (1,600 x 1,200) resolution images are intelligently
resized to 1,024 x 768 for full-screen or default
presentations.
*
DTV is the umbrella term used to describe the new digital
television system in the United States.
7. ANTI-ALIASING DIGITAL KEYSTONE CORRECTION
Digitally adjusts an image that is projected at an angle
while maintaining image quality and brightness. (Page 10)
8. DIGITAL IMAGE SHIFT FUNCTION
Allows digital adjustment of 16:9 wide-screen images up or
down for easier viewing. (Page 10)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. PROJECTOR FEATURES
CAUTIONS CONCERNING THE SETUP OF THE
PROJECTOR
For minimal servicing and to maintain high image quality,
PHILIPS recommends that this projector be installed in an area
TEMPERATURE MONITOR FUNCTION
If the projector starts to overheat due to setup problems or a
dirty air filter,’TEMP.’ and ‘ ’ will flash in the lower-left corner
of the picture. If the temperature continues to rise,the lamp
free from humidity, dust and cigarettesmoke. If the projector is will turn off,the Temperature warning indicator (Temp.) on the
used in these environments, the lens and filter will need to be
cleaned (or the filter replaced) more often, and internal
cleaning may become necessary. As long as the projector is
regularly cleaned, use in these environments will not reduce
the overall operation life of the unit. Internal cleaning should
only be performed by a Philips Authorised LCD Projector
Dealer or Service Centre.
projector will flash,and after a 90-second cooling-off period the
power will shut off. Refer to ‘Lamp / Maintenance Indicators’
on pages 29-31 for details.
Note:
The cooling fan regulates the internal temperature, and its
performance is automatically controlled. The sound of the fan
may change during projector operation due to changes in the
fan speed.
NOTES ON OPERATION
•The exhaust vent, the lamp cage cover and adjacent areas
may be extremely hot during projector operation. To prevent
injury, do not touch these areas until they have sufficiently
cooled.
LAMP MONITOR FUNCTION
When the projector is turned on after the lamp has been used
for 900 hours, ‘LAMP’ and ‘ ’ will flash in the lower-left
corner of the picture to advise you to replace the lamp.
See pages 30 and 31 for lamp replacement. If the lamp has
been used for 1,000 hours, the projector power will
automatically turn off and the projector will enter the standby
mode. Refer to ‘Lamp/Maintenance Indicators’ on page 29-31
for further details.
•Allow at least 10 cm (4 inches) of space between the cooling
fan (exhaust vent) and the nearest wall or obstruction.
•If the cooling fan becomes obstructed, a protection device
will automatically turn off the projector lamp. This does not
indicate a malfunction. Remove the projector powercord from
the wall outlet and wait at least 10 minutes.
104
F
('40 C)
41 F
('5 C)
Then turn on the power by plugging the powercord back in.
This will return the projector to the normal operating
condition.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
See illustrations on page 4
5. FUNCTIONAL OVERVIEW
CONTROLS
# Menu
On projector (fig. 1)
For activating and de-activating the On Screen Display
Menu
1 Power ON z
For switching the projector in power on.
Standby/OFF y
For switching the projector in standby mode.
$ Volume buttons (+/-)
To adjust audio volume level.
% Temperature warning indicator (Temp.)
2 Lens
Flashes when the temperature of the projector is too high
For selecting the optical lens adjustments Zoom, Focus,
Digital Keystone correction and Digital Image Shift (see
Note). The button toggles between the ZOOM-, FOCUS-,
KEYSTONE and DIGITAL SHIFT function.
Note:
^ Lamp replacement indicator (Lamp)
Lights to indicate the status of the lamp;
Green: lamp is ready
Flashing green: warming up
Red: change the lamp
Digital Image Shift feature can only be addressed while
being in the WIDE and NORMAL (WIDE) picture display
modes during video or DTV input.
& Audio / Video - Mute
(See page 24 for details.)
For muting the sound of the projector (or an externally
connected sound amplifier) and for muting the picture.
3 Data-1 button
For selecting the Data 1 signal as the current projection source.
* Power indicator y I
Lights up red when the projector enters standby mode.
Lights up green when the projector is turned on.
4 Data-2 button
For selecting the Data2 signal as the current projection source.
( Cooling fan
5 Video button
Intake of air for ventilation.
For selecting the video signal or S-video signal as the current
projection source.
) Kensington Security Standard connector
Slit for inserting an optional locking device (Kensington lock).
6 Auto sync
For activating the Auto sync operation in Data mode.
¡ Carrying handle
7 OK
™ Foot releases/height adjustment
For action confirmation in the menu when the menu is on
the screen (activated)
For adjusting the height and vertical angle of the projector.
£ Remote control sensors
8
Cursor Control
Receive the signals from the remote control.
When the menu is active the Cursor Control buttons control the
menu cursor. The cursor control, by means of the local
keyboard, works with up/down and left/right button operation.
≤ Speakers
∞ Cooling fan
9 D-Zoom
For addressing the D-Zoom function. The button toggles
Exhaust of air for ventilation.
between the digital magnification factors, x1, x2, x3, x4, x6
and x8.
§ Air filter/Cooling fan
0 D-Freeze button
Digital Freeze function: to instantly freeze a moving image.
! V-Effect button
Digital Video Effect correction: to enhance image quality.
@ V-Format button
Allows to modify or customise the picture display mode.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
See illustrations on page 4
5. FUNCTIONAL OVERVIEW
REMOTE CONTROL
(fig. 2)
CONNECTIONS
(fig. 3)
1 On / Off switch z / y
A Data 1 in (15 pin)
For switching the remote control as well as the projector
on and off.
Input socket for connecting to the Data out terminal of a
computer.
Note:
B Audio 1 in (3.5 mm stereo minijack)
Input socket for connecting to the Audio out terminal of a
computer or any other audio equipment.
The remote control will always use some power, even when
not in use. The remote control unit will automatically switch off
when not used for 30 minutes.
C Data 2 in (15 pin)
2
Tracking Ball
Input socket for connecting to the Data out terminal of a
computer.
For manipulating the mouse cursor on the connected computer.
Notes:
D Audio 2 in (3.5 mm stereo minijack)
Input socket for connecting to the Audio out terminal of a
computer or any other audio equipment.
– The Tracking Ball only functions when the provided USB
Mouse Receiver is connected to the USB port of a PC.
– The minimum system requirements for the USB Mouse
receiver are Windows 98 and/or Windows 2000 or higher.
– A cursor control requires the presence of data signal.
E Data 1 in (BNC) (R (Pr), G/G sync (Y), B (Pb),
HD (C sync), VD)
Input sockets for connecting Data 1 BNC connection.
3
Mouse left and Mouse Right (-/--)
The mouse left/right buttons (-/--) on the remote control
function as the left and right mouse buttons of your PC,
only in case the provided USB Mouse receiver properly is
connected to the PC.
F Data out (15 pin)
Output socket for connecting to the Data in terminal of another
data projector or data monitor.
G Audio out (3.5 mm stereo minijack)
Output socket for connecting to the Line Input sockets of an
amplifier or stereo system.
4 Cursor Control
To operate and navigate through the activated menu via
up/down and the left/right cursor buttons
H AC socket
5 Auto sync
For connecting the projector to the powercord.
For activating the Auto sync operation in Data mode.
I S-Video in (4 pin mini DIN)
6 Input
Input socket for connecting to any other Audio Video
equipment equipped with a S-Video output socket.
For selecting in sequence the Data or Video signal as the
current projection source.
The button toggles between Data 1, Data 2 or Video signal.
J RS-232C port (9-pin mini-DIN)
For connecting a computer to the projector with a RS-232C
cable (optional). The computer can be used in this way to
control the projector.
7 Audio / Video - Mute
For muting the sound of the projector (or an externally
connected sound amplifier) and for muting the picture.
K Video in (RCA)
8 Lens
Input socket for connecting to any other Audio Video
equipment equipped with a Video output socket. (PAL, NTSC,
SECAM).
For selecting the optical lens adjustments Zoom, Focus,
Digital Keystone correction and Digital Image Shift (see
Note). The button toggles between the ZOOM-, FOCUS-,
KEYSTONE and DIGITAL SHIFT function.
Note:
Digital Image Shift feature can only be addressed while
being in the WIDE and NORMAL (WIDE) picture display
modes during video or DTV input. (See page 24 for details.)
L Audio in L/R (RCA)
Input sockets for connection to the AUDIO OUT sockets of a
video recorder (S-VHS, PAL, NTSC, SECAM).
M 15 pin/BNC switch
To switch between 15 pin or BNC Data 1 input.
9 OK
For action confirmation in the menu when the menu is on
the screen (activated)
0 D-Zoom
For addressing the D-Zoom function. The button toggles
between the digital magnification factors, x1, x2, x3, x4, x6
and x8.
! Menu
For activating and de-activating the On Screen Display
Menu
@ Back light
For switching on the button illumination.
The back-light will switch off automatically after 5 seconds.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
6. SET UP
POSITIONING THE PROJECTOR AND SCREEN
POWER SUPPLY
Position the projector perpendicular to the screen with all
feet flat and level to achieve an optimal image. Move the
projector forward or backward if the edges of the image are
distorted.
• The projector lens should be centred in the middle of the
screen. If the lens centre is not perpendicular to the screen,
the image will be distorted, making viewing difficult.
• Position the screen so that it is not in direct sunlight or room
light. Light falling directly onto the screen washes out
colours, making viewing difficult. Close the curtains and dim
the lights when setting up the screen in a sunny or bright
room.
• A polarising screen cannot be used with this projector.
• Place the projector at the required distance from the screen
according to the desired picture size (see the table below).
• Optional wide and telephoto lenses from Philips are available
for specialised application. Please see your local Philips
Authorised LCD Projector Dealer for details on the optional
lenses.
1. Insert the powercord into the projectors AC socket and
connect it to the wall socket.
Note:
The Power indicator lights up red, the projector is now in the
Power/Standby mode.
2. Remove the lens cap.
3. Press Power On.
• The power indicator lights up green and the flashing green
Lamp indicator shows that the lamp is warming up. Wait
until the indicator stops flashing before operating the
projector. The image shown is the Philips start-up screen
(default setting).
• If the power is turned off and then immediately turned on
again, it may take a short while before the lamp turns on.
• After the projector is unpacked and turned on for the first
time, a slight odour may be emitted from the exhaust vent.
This odour will soon disappear with use.
Standard mode (4:3)
When the power is on, the Lamp indicator lights indicating the
status of the lamp.
Image size
(diag.)
Projection distance
Tele
Distance lens
center to bottom
of image
Wide
Green: lamp is ready.
Flashing green: warming up.
Red: change the lamp.
mtrs
1,02
1,52
1,83
2,13
2,54
3,81
5,08
7,62
inch
40
60
72
mtrs
1,40
2,20
2,60
3,10
3,70
5,60
7,40
11,00
inch
55
87
102
122
146
220
291
433
mtrs
1,90
2,90
3,40
4,00
4,90
7,20
9,80
14,30
inch
75
cm
inch
1,22
1,81
2,17
2,52
2,99
4,49
5,98
9,02
3,10
4,60
5,50
6,40
7,60
11,40
15,20
22,90
114
134
157
193
283
386
563
4. To switch off the power supply completely, pull the
powercord plug out of the wall socket.
84
100
150
200
300
Note:
Before disconnecting the powercord, make sure that the
cooling fan has stopped (about 2 minutes after the projector
has been switched off).
Wide mode (16:9)
Image size
(diag.)
ADJUSTING THE VERTICAL AND HORIZONTAL ANGLE OF
THE PROJECTOR
Projection distance
Tele
Distance lens
center to bottom
of image
Wide
Using the adjustment feet
• Press foot releases.
• Adjust height of projector and remove hands from foot
releases.
• Rotate feet to make fine adjustments.
mtrs
1,02
1,52
1,83
2,13
2,34
2,54
2,69
3,38
3,81
5,08
7,62
inch
40
60
72
84
mtrs
1,50
2,40
2,80
3,30
3,70
4,00
4,30
5,40
6,10
8,10
12,0
inch
59
94
mtrs
2,00
3,10
3,70
4,30
4,80
5,20
5,60
7,00
7,90
10,50
15,60
inch
79
cm
inch
-5,00
-7,50
-9,00
-1,97
-2,95
-3,54
-4,13
-4,53
-4,92
-5,20
-6,54
-7,36
-9,80
-14,72
122
146
169
189
205
220
276
311
413
614
110
130
146
157
169
213
240
319
472
-10,50
-11,50
-12,50
-13,20
-16,60
-18,70
-24,90
-37,40
92
100
106
133
150
200
300
)
Notes:
– Tolerances 3% in above mentioned values.
– Values with a minus (-) sign indicate the distance of the lens
centre below the bottom of the screen.
• The projector is adjustable up to approximately 5° from the
standard position.
• When the height of the projector is adjusted, the image
may become distorted (keystoned),
depending on the relative positions of the
projector and the screen.
(See ‘Lens adjustment’).
Keystoned Image
CAUTION!
– Do not press the foot releases when the adjustment feet are
extended without firmly holding the projector.
– Do not hold the lens when lifting or lowering the projector.
– When lowering the projector, be careful not to get your
fingers caught in the area between the adjustment feet and
the projector.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. SET UP
LENS ADJUSTMENT
Digital Shift (16:9 mode)
When a WIDE or NORMAL (WIDE) image is projected, this
function can be used to shift the image up or down.
Focus, Zoom, Digital Keystone correction and
Digital Image Shift (see ‘Digital Shift’)
1. Press Lens to select mode.
– Each time Lens is pressed, the screen changes in the
following order.
1. Press Lens to select ‘DIGITAL SHIFT’.
2. Press OK to display test pattern.
3. Press 1, 2, 3 or 4 to make adjustments.
4. Press Lens until normal screen apprears.
4:3 Normal image
16:9 Wide image
Note:
This function only works with WIDE and NORMAL (WIDE)
picture display modes during video or DTV input.
(See page 24 for details.) The Digital Shift screen is not
displayed when projecting images other than WIDE or
NORMAL (WIDE).
Notes:
– The On Screen Displays will automatically disappear when
no changes have been made within 30 seconds.
– Straight lines and the edges of the displayed image may
appear jagged, when adjusting the KEYSTONE setting.
– Do not touch the lens when adjusting the focus or zoom.
FOCUS
NEXT (Lens)
FOCUS
ADJUST
NEXT (Lens)
ADJUST
OK
OK
CAUTION!
When all required adjustments have been made, switch off the
projector before making any other connections (see
‘Installation’).
MOVING THE PROJECTOR
1. Press the Standby/OFF button to switch off the projector.
The standby indicator lights up red.
2. Wait until the cooling fan has stopped (about 2 minutes
after the projector has been switched off) and disconnect
the powercord and all other cables.
ZOOM
ZOOM
NEXT (Lens)
ADJUST
NEXT (Lens)
ADJUST
OK
OK
3. Put the lens cap back in place to prevent dust, dirt or other
contamination from harming or damaging the front of the
projector lens when moving the projector.
4. When transporting the projector, carry it by the carrying
handle on the side.
KEYSTONE
END (Lens)
CAUTION!
ADJUST
KEYSTONE
Do not lift or carry the projector by the lens or the lens cap as
this may damage the lens.
OK TEST PTRN
END (Lens)
ADJUST
OK TEST PTRN
INSERTING THE BATTERIES IN THE REMOTE CONTROL
Push
DIGITAL SHIFT
I
END (Lens)
ADJUST
OK TEST PTRN
2. Press OK to display test pattern.
1. Press in and downward on the arrow to remove the battery
cover.
2. Insert three AA size batteries for the remote control, making
sure their polarities match the (+) and (-) marks inside the
battery compartment.
KEYSTONE
END
ADJUST
OK
EXIT TEST PTRN
3. Insert the side tabs of the battery cover into their slots and
press the cover in until it is properly seated.
3. Press 1, 2, 3 or 4 to make adjustments.
CAUTION!
Do not mix old and new batteries (also never mix alkaline and
manganese batteries).
4. Press Lens until normal screen appears.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Video/computer cables and adapter
7. INSTALLATION
VIDEO/COMPUTER CABLES AND ADAPTER
These accessories are supplied for connecting the projector to computer/Audiovisual equipment. The numbers in the left-hand
column correspond with the numbers in the connection diagrams on the following pages.
CONNECTIONS
Computer/AV products side
No.
1
CABLE/ADAPTER
Projector side
Computer VGA Cable
RCA Audio Video Cable
Mini D-Sub
15P (male)
Mini D-Sub
15P (male)
2
RCA pin
RCA pin
(male) x 3
(male) x 3
3
4
5
6
7
8
Computer Audio Cable
Scart/RCA-AV Adapter
S-Video Cable
3.5 mm stereo
minijack
3.5 mm stereo
minijack
Mini Din 4P
(male)
Mini Din 4P
(male)
BNC-RCA adapters (3x)
DIN-D-sub RS-232C cable
USB mouse receiver
x 3
x 3
Mini D-Sub
9P (male)
Mini Din
8P (male)
USB connector
4P (female)
Optional cable: – Computer cable Mini D sub (15 pin)-BNC connectors (5x),
type number (LCA5311: 8670 953 1109)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a computer
7. INSTALLATION
CONNECTING TO A COMPUTER
General
– The data input (Data 1 and 2) is suitable for both Apple Macintosh computers (Power Book and Power Mac) as well as for IBM
compatible PCs.
– The data output of IBM compatible PCs can be connected directly to the projector using standard computer VGA cable.
– Apple Macintosh computers may need a conversion plug (optional) added to the standard computer VGA cable.
– The figures in brackets (1) correspond to the figures in the diagram on page 11, the characters in brackets (A) correspond to the
characters in fig. 3 on page 4.
– Caution: Always switch off the projector and computer before making any connections!
After making all connections, turn the projector on first. The computer should always be turned on last.
Connecting an IBM-PC or a Macintosh computer using the
standard 15 pin input connector (Data 1 and Data 2)
Connecting to an external RGB switcher or other compatible
computers using the BNC input connectors (Data 1)
Computer
in (15pin)
-
RGB
/
Component inputs
Data in
Computer
in (15pin)
-
RGB
/
Component inputs
Data in
Data
1
2
Data
1
2
Audio1
Audio2
Audio1
Audio2
(A)
(B)
(B)
Data
R
1
in (BNC)
Data
R
1
in (BNC
15pin
BNC
(Pr)
/G sync (Y)
B
(Pb)
HD (C sync)
VD
15pin
BNC
(Pr)
/G sync (Y)
B
(Pb)
HD (C sync)
VD
(E)
(M)
(M)
APPARATSKA
ANSLUTAS TILL
JODAT UTTAG.
APPARATEN SKALL
ANSLUTAS TILL
JODAT UTTAG.
Audio in
Video in
Data out
Audio out
in
eo in
Data
out
L
R
R
110-120V / 220-240V~
110-1200-240V~
RS-232C
S-Videin
RS-232C
S-Vido in
(3)
(1)
Optional
(3)
Mouse
Data out
Audio out
USB
When connecting this projector to a computer, select
‘Computer-RGB’ for ‘Signal Type’ on the GUI ‘Picture’ menu.
(See page 20)
Mouse
Data out
Audio out
USB
1. To use the Standard 15-pin connector, slide the 15 pin/BNC
switch (M) on the rear terminals to the 15 pin position.
2. Connect one end of the supplied computer cable (1) to the
Computer-RGB Input Data 1 (A) or 2 port on the projector.
3. Connect the other end to the Monitor output port on the
computer. Secure the connectors by tightening the thumb
screws.
4. To use the built-in audio system, connect one end of the
supplied computer audio cable (3) to the Audio 1 (B) or 2
terminal on the projector.
When connecting this projector to a computer, select
‘Computer-RGB’ for ‘Signal Type’ on the GUI ‘Picture’ menu.
(See page 20)
1. To use the 5 BNC connectors, slide the 15 pin/BNC switch (M)
on the rear terminals to the BNC position.
2. Connect each BNC connector to the corresponding BNC Input 1
terminal (E) on the projector.
3. Connect the R (Pr), G/G sync (Y), B (Pb), HD (C sync) and VD
cables to the correct input terminals on the projector and an
RGB switcher (optional) connected to the computer, or
connect a 5 BNC cable (optional) directly from the input
terminals on the projector to the computer.
4. To use the built-in audio system, connect one end of the
supplied computer audio cable (3) to the Audio Input 1 terminal
(B) on the projector.
5. Connect the other end to the Audio output terminal on the
computer.
Notes:
–
A Macintosh adapter may be required for use with some
Macintosh computers. Contact your nearest Philips Authorised
LCD Projector Dealer or Service Centre.
–
–
–
Audio Input 1 accepts Data 1 port input, Audio Input 2 accepts
Data 2 port input.
A 3.5 mm minijack to RCA audio cable adapter may be
necessary.
When connecting the projector to a compatible computer other
than an IBM-PC (VGA/SVGA/XGA/SXGA/UXGA) or Macintosh
(i.e. Workstation), a separate cable may be needed. Please
contact your dealer for more information.
Connecting computers other than the recommended types may
result in damage to the projector, the computer, or both.
5. Connect the other end to the Audio output terminal on the
computer or external audio system.
Notes:
–
–
–
This projector uses a 5 BNC computer input to prevent
deterioration of image quality.
–
A 3.5 mm minijack to RCA audio cable adapter may be
necessary.
When connecting the projector to a compatible computer other
than an IBM-PC (VGA/SVGA/XGA/SXGA/UXGA) or Macintosh
(i.e. Workstation), a separate cable may be needed. Please
contact your dealer for more information.
‘Plug and Play’ function (when connecting to a 15 pin
terminal)
• This projector is compatible with VESA-standard DDC 1/DDC 2B.
The projector and a VESA DDC compatible computer will
communicate their setting requirements, allowing for quick and
easy setup.
–
Connecting computers other than the recommended types may
result in damage to the projector, the computer, or both.
• Before using the ‘Plug and Play’ function, be sure to turn on the
projector first and the connected computer last.
• The DDC, Plug and Play function of this projector operates only
when used in conjunction with a VESA DDC compatible
computer.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to video equipment
7. INSTALLATION
CONNECTING TO VIDEO EQUIPMENT
General
– The figures in brackets (1) correspond to the figures in the diagram on page 11
.
The characters in brackets (A) correspond to characters in fig. 3 on page 4.
– Caution: Always turn off the projector while connecting to video equipment, in order to protect both the projector and the
equipment being connected.
VCR, Laser disc, other audiovisual equipment using
standard video input
DVD, DTV, other component video equipment using 5 BNC
input
Computer
in (15pin)
-
RGB
/
Component inputs
Data in
Computer
in (15pin)
-
RGB
/
Component inputs
Data in
Data
1
2
Data
1
2
Audio1
Audio2
Audio1
Audio2
(B)
Data
R
in (BNC)
Data
R
1
in (BNC)
15pin
BNC
(Pr)
G/G
(Y)
B
(Pb)
HD (C sync)
VD
sync (E)
15pin
BNC
(Pr)
G/G sync (Y)
B
(Pb)
HD (C sync)
VD
(M)
(M)
APPARATEN SKALL
ANSLUTAS TILL
JODAT UTTAG.
APPARATEN SKALL
ANSLUTAS TILL
JODAT UTTAG.
Aud
eo i
Data out
Audio out
Audio in
Video in
Data out
Audio out
L
R
(6)
(K)
(L)
110-120V / 220-240V~
110-120V / 220-240V~
RS-232C
S-Video in
RS-232C
S-Vieo in
Optional
(2)
(2)
Scart/RCA adapter
(Europe only)
(4)
Video
out
L Audio
out
R
L Audio
out
R
VViiddeeooBBNNCC
oouutt
1.Connect the yellow RCA connector (K) to the corresponding
yellow Video Input terminal on the projector and the Video
output terminal on the video source.
2.To use the built-in audio system, connect the red and white
RCA connectors to the corresponding red and white Audio
Input terminals on the projector (L) and the Audio output
terminals on the video source.
1.To use the 5 BNC connector, slide the 15 pin/BNC switch
(M) on the rear terminals to the BNC position. Connect each
BNC connector to the corresponding BNC Input 1 terminals
(E) on the projector. (BNC-RCA adapters (6) are included for
use with RCA type cables and sources.)
2.Connect the other end of the cable (2) to the corresponding
terminals of a DVD player or DTV decoder.
3.To use the built-in audio system, connect one end of the
computer audio cable (optional) to Audio Input 1 terminal
(B) on the projector. Connect the other end to the Audio
output terminal on the video source.
In case your VCR, Laser Disc player, video camera or TV is
equipped with a Scart connector:
1. Connect the Scart/RCA Audio Video adapter supplied (4) to
the Scart connector of the VCR, Laser Disc player, video
camera or TV.
2. Plug the video/audio connection cable (2) supplied into both
the adapter and the Video in (K) and Audio in(L/R) sockets
(L) of the projector.
When connecting the projector to a DVD player or a DTV
decoder equipped with Component video outputs, select
‘Component’ for ‘Signal Type’ in the GUI ‘Picture’
menu (see page 20).
In case your Audiovisual equipment is equipped with a S-
Video connector:
The S-Video Input terminal uses a video signal system in which
the picture is separated into a color and a luminance signal to
realize a higher-quality image.
Note:
After the use of ‘Component’, when connecting to a computer
again, select ‘Computer/RGB’ for ‘Signal Type’ in the GUI
‘Picture’ menu (see page 20).
1. Plug the S-Video connection cable supplied (5) into the
Audiovisual equipment and the S-Video in socket (I) of the
projector.
2. Plug an audio connection cable (optional) or the video/audio
connection cable (2) supplied into both the Audio in L/R
sockets (L) of the projector and the Audio out L/R sockets
of the Audiovisual equipment.
Insert the white plug into the L socket and the red plug into
the R socket.
Note:
If your video equipment does not have an S-video output
terminal, use the Composite video output terminal.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to audio equipment/remote control mouse receiver
7. INSTALLATION
CONNECTING TO AUDIO EQUIPMENT/THE REMOTE CONTROL MOUSE RECEIVER
General
– The figures in brackets (1) correspond to the figures in the diagram on page 11
.
– The characters in brackets (A) correspond to characters in fig. 3 on page 4.
CONNECTING TO AUDIO EQUIPMENT
CONNECTING THE REMOTE CONTROL MOUSE RECEIVER
CAUTION!
When the RS-232C port on the projector is connected to a
computer with an RS-232C cable (cross type, sold separately),
the computer can be used to control the projector and check
the status of the projector.
Always turn off the projector while connecting to audio
components, in order to protect both the projector and the
components being connected. By using external audio
components, the volume can be amplified for better sound.
Computer
in (15pin)
-
RGB
/
Component inputs
Data in
Data
1
2
Audio1
Audio2
Data
R
1
in (BNC)
15pin
BNC
(Pr)
G/G sync (Y)
B
(Pb)
HD (C sync)
VD
APPARATEN SKALL
ANSLUTAS TILL
JODAT UTTAG.
Audio in
Video in
Data out
Audio out
L
R
(G)
110-120V / 220-240V~
RS-232C
S-Video in
Optional
Computer
Mouse
Data out
Audio out
USB
L Audio
in
R
(8)
• Connect the Audio in L/R sockets of an amplifier or stereo
system to the Audio out socket (G) of the projector.
For this, use an audio connection cable (optional).
• Connect the supplied USB mouse receiver to the
corresponding USB terminal on the PC.
CAUTION!
– The minimum system requirements for the USB mouse
receiver are Windows 98 and/or Windows 2000 or higher.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
8. OPERATION
PREPARATION
Notes:
Turning on/off the power
– Wait until the cooling fan stops (about 2 minutes after the
projector has been switched off) before disconnecting the
powercord.
1. Make the necessary connections before proceeding.
Connect the powercord to a wall outlet.
The Power indicator lights up red and the projector enters
standby mode.
– The power can be turned on again by pressing Power ON.
When the power is turned on, the Power indicator and the
Lamp indicator light green.
2. Press Power ON.
The power indicator lights up green and the flashing green
Lamp indicator shows that the lamp is warming up. Wait
until the indicator stops flashing before operating the
projector.
If the power is turned off and then immediately turned on
again, it may take a short while before the lamp turns on.
USING THE REMOTE CONTROL
(fig. 2)
The remote control has the following two functions:
• Projector control
• Wireless mouse
Notes:
• Slide the remote control power ON/OFF switch into the ON
position for switching the projector and the Remote Control
unit to on.
– The remote control can be used to control the projector
within the ranges shown below.
– The USB mouse receiver can be used with the remote
control to control the mouse functions of a connected
computer within the ranges shown below.
– If the bottom filter cover is not securely installed, the Power
indicator flashes in red.
– After the projector is unpacked and turned on for the first
time, a slight odour may be emitted from the exhaust vent.
This odour will soon disappear with use.
Remarks:
1) When the power is on, the Lamp indicator (Lamp) indicates
the status of the lamp.
7m (23'8)
Green: lamp is ready.
Flashing green: warming up.
Red: change the lamp.
30˚
2) After the picture is displaying, the warming-up indicator
‘WARMING UP, PLEASE WAIT’ is shown
45˚
30˚
45˚
3. Press the button of the desired input mode, Data 1, Data 2,
Video.
30˚
On the remote control press the Input button to select the
desired input mode (Data 1, Data 2, Video).
Press Input again to change the mode. Example:
DATA
DATA
– When no signal is being received, ‘NO SIGNAL’ will be
displayed. When a signal that the projector is not preset to
receive is being received, ‘NOT REG.’ will be displayed.
4. Press Volume to adjust the volume. (on the local keyboard
only)
4m (13'8)
45˚
30˚
Using the remote control in a dark room
•
Press BACKLIGHT, and the buttons will light up.
5. Press A/V Mute to temporarily turn off the sound and
Notes:
picture.
– Be sure the supplied USB mouse receiver is connected to
your computer.
– The wireless mouse may not operate correctly if your
computer serial port is not correctly set up. Refer to the
computer’s operation manual for details of setting
up/installing the mouse driver.
– For one-button mouse systems, use either the LEFT-CLICK
or RIGHT-CLICK button.
Press A/V Mute again to turn the sound and picture back on.
6. Press Standby/OFF for switching off the projector.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Graphical User Interface
8. OPERATION
GRAPHICAL USER INTERFACE
Using the GUI (Graphical User Interface) Menu Screens
This projector has two sets of menu screens (Data/Video) that allow you to adjust the image and various projector settings.
These menu screens can be operated from the projector or the remote control with the following buttons.
Note:
The On Screen Displays will automatically disappear when no changes have been made within 30 seconds.
DATA MODE MENU CONTROL
VIDEO MODE MENU CONTROL
1. Press Menu to display the Data mode menu bar.
1. Press Menu to display the Video mode menu bar.
2. Press 1 / 2 to select an adjustment menu on the menu
bar.
3. Press 3 / 4 to select a specific adjustment item.
4. To display a single adjustment item, press OK after
selecting the item.
2. Press 1 / 2 to select an adjustment menu on the menu
bar.
3. Press 3 / 4 to select a specific adjustment item.
4. To display a single adjustment item, press OK after
selecting the item.
– Only the menu bar and the selected adjustment item will
appear.
– Only the menu bar and the selected adjustment item will
appear.
5. Press 1 / 2 to adjust the item.
6. Press Menu to exit from the GUI.
5. Press 1 / 2 to adjust the item.
6. Press Menu to exit from the GUI.
LANGUAGE SELECTION
English is the default setting language for the On-Screen
Display. It can be changed to English, German, Spanish, Dutch,
French, Italian, Swedish or Portuguese.
1. Press Menu.
– The menu bar appears on the screen.
2. Press 1 / 2 to select ‘Language’.
3. Press 3 / 4 to select the desired language.
4. Press OK to save the setting. The On-Screen Display is now
programmed to display in the language selected.
5. To exit from the GUI, press Menu.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture control
8. OPERATION
PICTURE CONTROL
– The projector’s picture is set to standard specifications at the factory. However, you can adjust the image to suit your own
preferences by using the Data or Video ADJUST feature.
– The projector will store the last used settings for every source. So when you switch from one source to another, the settings
of the source switched from will be stored and the settings of the source switched to will be recalled.
– When the projector is switched off and on again the settings for the selected source will be recalled again.
– Three memory modes allow you to adjust and save up to three sets of settings (see ‘Personal Preferences’).
DATA MODE INPUT SIGNAL
VIDEO MODE INPUT SIGNAL
Data mode input selection
Video mode system selection
Ordinarily, the type of input signal is detected and the correct
resolution mode is automatically selected. However, for some
signals, ‘Special Modes’ on the ‘Fine Sync’ menu screen may
need to be changed to match the computer display mode.
The video input system mode is preset to ‘Auto’; however, it
can be changed to a specific system mode, if the selected
system mode is not compatible with the connected audiovisual
equipment.
1. Press Menu.
2. Press 1 / 2 to select ‘Fine Sync’.
3. Press 3 / 4 to select ‘Special Modes’.
1. Press Menu.
2. Press 1 / 2 to select ‘Options’.
3. Press 3 / 4 to select ‘Video System’.
4. Press OK to move into the Video System mode.
5. Press 4 to select the desired video system mode.
6. Press OK to save the setting.
4. Press OK to move into the Special Modes.
5. Press 4 to select the optimal resolution mode.
6. Press OK to save the setting.
7. To exit from the GUI, press Menu.
7. To exit from the GUI, press Menu.
Notes:
– Avoid displaying computer patterns which repeat every other
line (horizontal stripes). (Flickering may occur, making the
image hard to see.)
– When inputting DTV 480P signals, select ‘480P’ in step 4
above.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture control
8. OPERATION
DATA MODE DISPLAY
Auto Sync Adjustment
– Used to automatically adjust a computer image.
– Auto Sync adjustment can be made manually by pressing
Auto sync (either on local keyboard and remote control), or
automatically by setting ‘Auto Sync’ to ‘ON’ in the
projector’s GUI menu.
Data display Fine Sync adjustments
When displaying computer patterns which are very detailed
(tiling, vertical stripes, etc.), interference may occur between
the LCD pixels, causing flickering, vertical stripes, or contrast
irregularities in portions of the screen. Should this occur, adjust
‘Clock’, ‘Phase’, ‘H-Pos’ and ‘V-Pos’ for optimum computer
image (Fine Sync adjustment).
When ‘Auto Sync’ is set to ‘ON’:
– The sync adjustment is automatically made each time the
projector is turned on while connected to a computer or the
input selection is changed.
1. Select the desired computer input mode by pressing either
Data 1 or Data 2 at the projector local keyboard or toggling
the Input button on the Remote Control unit.
2. Press Menu. Menu bar and ‘Picture’ menu screen appear.
GUI operation guide is also displayed.
3. Press 1 / 2 to select ‘Fine Sync’.
– The Auto Sync adjustment setting previously made is
cleared when the projector’s setting is changed.
1. Press Menu.
2. Press 1 / 2 to select ‘Fine Sync’.
3. Press 3 / 4 to select ‘Auto Sync’.
4. Press 3 / 4 to select a specific adjustment item.
4. Press 1 / 2 to select ‘ON’.
5. To exit from the GUI, press Menu.
• Automatic adjustments can be made by pressing Auto sync.
• When the optimum image cannot be achieved with Auto
Sync adjustment, use manual adjustments. (See ‘Data
display Fine Sync adjustment’).
During Auto Sync adjustment, the On-Screen Display changes:
5. Press 1 / 2 to move the ‘I’ mark of the selected
adjustment item to the desired setting.
6. To exit from the GUI, press Menu.
Note:
To reset all adjustment items, select ‘Reset’ on the ‘Fine Sync’
menu screen and press OK.
Description of Adjustment Items
Selected item
Clock
Phase
Description
Adjusts vertical noise
Adjusts horizontal noise (similar to tracking
on VCR)
Note:
H-Pos
V-Pos
Centers the on-screen image by moving it to
the left or right
Centers the on-screen image by moving it up
or down
Auto Sync adjustment may take some time to complete,
depending on the image of the computer connected to the
projector.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture control
8. OPERATION
Auto Sync Display Function
3. Press 1 / 2 to move the mark of the selected adjustment
Normally, an image is not superimposed during Auto Sync
adjustment. You can, however, choose to superimpose a
background image during Auto Sync adjustment.
item to the desired setting.
1. Press Menu.
2. Press 1 / 2 to select ‘Fine sync’
3. Press 3 / 4 to select ‘Auto Sync Disp’.
4. To exit from the GUI, press Menu.
Notes:
– To reset all adjustment items, select ‘Reset’ on the ‘Picture’
menu screen and press OK.
– The adjustments can be stored separately in the ‘Data 1’,
‘Data 2’ and ‘Video’ modes.
– For Component input in Data mode, ‘Sharpness’ may not be
adjustable depending on the type of signal received.
4. Press 1 / 2 to select ‘ ’ to superimpose a background
image or ‘ ’ to remove the background image during Auto
Sync adjustment.
Color Temperature adjustments
5. To exit from the GUI, press Menu.
This function can be used to adjust the color temperature to
suit the type of image input to the projector (Video, computer
image, TV broadcast, etc.)
DATA MODE / VIDEO MODE DISPLAY
Decrease the color temperature to create warmer, reddish
images for natural flesh tones. Increase th color temperature
to create cooler, bluish images for a brighter picture.
Picture adjustments
For Data / Video signal input, the following adjustments can be
made:
– Contrast - adjusts the overall contrast intensity;
– Bright - adjusts the picture brightness;
– Color - adjusts the colour saturation of the projected image;
– Tint - for more purplish/greenish skin tones (NTSC only);
– Sharpness - adjusts the overall picture sharpness;
– Red - for weaker/stronger red images;
– Blue - for weaker/stronger blue images;
– Color Temperature – adjusts the colour temperature of the
projected image;
Description of Color Temperature:
- Decrease color temperature for warmer, reddish,
incandescent-like images (Low color temperature)
- Increases color temperature for cooler, bluish, florescent-like
images (High color temperature)
1. Press Menu.
– Menu bar and ‘Picture’ menu screen appear. GUI operation
guide is also displayed.
– Reset - all image adjustment items are returned to the
factory preset settings.
2. Press 3 / 4 to select ‘CLR Temp’.
– Signal type – allows to select the input signal type (Data mode
only)
– I/P conversion – allows to select either an interlaced display or
a progressive display of a video signal;
Note:
‘Color’, ‘Tint’ and ‘Sharpness’ do not appear for Computer/RGB
input in Data mode.
1. Press Menu.
– Menu bar and ‘Picture’ menu screen appear. GUI operation
guide is also displayed.
2. Press 3 / 4 to select a specific adjustment item.
3. Press 1 / 2 to move the mark of the selected adjustment
item to the desired setting.
4. To exit from the GUI, press Menu.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture control/Audio control
8. OPERATION
Selecting signal type
AUDIO CONTROL
This function allows you to select the input signal type
(Computer/RGB or Component) for Data in 1 or 2 port.
1. Press Menu.
This projector’s audio is factory preset to standard settings.
However, you can adjust it to suit your own preferences by
adjusting the following audio settings.
2. Press 1 / 2 to select ‘Picture’.
– Volume – adjusts audio level;
3. Press 3 / 4 to select ‘Signal Type’, and then press 2.
– Balance – adjusts audio level of left and right speaker;
– Treble – adjusts the high tones;
– Bass – adjusts the bass tones;
– Reset – All audio adjustment items are returned to the
factory preset settings.
1. Press Menu. Menu bar and ‘Picture’ menu screen appear.
GUI operation guide is also displayed.
4. Press 3 / 4 to select ‘Computer/RGB’ or ‘Component’.
5. Press OK to save the setting.
6. To exit from the GUI, press Menu.
2. Press 1 / 2 to select ‘Audio’.
3. Press 3 / 4 to select a specific adjustment item.
Interlaced (I)/Progressive (P) conversion
This function allows you to select either an interlaced display
or a progressive display of a video signal. The progressive
display projects a smooth video image.
1. Press Menu.
2. Press 1 / 2 to select ‘Picture’.
4. Press 1 / 2 to move the mark of the selected adjustment
item to the desired setting.
5. To exit from the GUI, press Menu.
Notes:
– To reset all adjustment items, select ‘Reset’ on the ‘Audio’
menu screen and press OK.
– The volume can also be adjusted with the ‘–’ Volume ‘+’
buttons on the projector.
3. Press 3 / 4 to select ‘I/P Conversion’, and then press 2.
4. Press 3 / 4 to select ‘Interlaced’ or ‘Progressive’.
5. Press OK to save the setting.
6. To exit from the GUI, press Menu.
Interlaced mode
Interlaced mode creates a single image through the activation
of scanning lines in two fields. Use this mode when projecting
moving images
Progressive mode
Progressive mode creates a single image using all available
scanning lines. Use this mode when projecting still images to
avoid flicker and stripes that result from interlaced source still
images.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Personal preferences
8. OPERATION
PERSONAL PREFERENCES
Selecting a saved setting
1. Press Menu.
This projector allows you to store up to seven adjustment
settings for use with various computers. Once these settings
are stored, they can be easily selected each time you connect
the computer to the projector.
2. Press 1 / 2 to select ‘Fine Sync’.
3. Press 3 / 4 to select ‘Select Setting’, and then press 2.
4. Press 3 / 4 to select the desired memory setting.
5. Press OK to select the setting.
6. To exit from the GUI, press Menu.
Saving/changing the adjustment setting
1. Press Menu.
2. Press 1 / 2 to select ‘Fine Sync’.
Notes:
– If the memory position has not been set, the resolution and
frequency will not be displayed.
– When selecting the stored adjustment setting with ‘Select
Setting’, the computer system should match the stored
setting.
3. Press 3 / 4 to select ‘Save Setting’, and then press OK.
4. Press 3 / 4 to select the desired memory location of the
setting.
5. Press OK to save the setting.
6. To exit from the GUI, press Menu.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
9. OTHER SETTINGS
REVERSE/INVERT IMAGE FUNCTION
Projection using a mirror
– Place a mirror (normal flat type) in front of the lens.
– The image reflected from the mirror is projected onto the
screen.
This projector is equipped with a reverse/invert image function
which allows you to reverse or invert the projected image for
various applications.
– Optimal image quality is produced with the projector
positioned perpendicular to the screen with all feet flat and
level.
Front
Normal image
Ceiling+Front
Inverted image
CAUTION!
When using a mirror, be sure to carefully position both the
projector and the mirror so the light does not shine into the
eyes of the audience.
Ceiling-mount Setup
– It is recommended that you use the optional ceiling-mount
bracket for this installation.
– Before mounting the projector, contact your nearest
Authorised LCD Projector Dealer or Service Centre to obtain
the recommended ceiling-mount bracket (sold separately). –.
When the projector is in the inverted position, use the upper
edge of the screen as the base line.
Rear
Reversed image
– Use the projector’s menu system to select the appropriate
projection mode.
DIGITAL FREEZE FUNCTION (D-FREEZE)
(on projector keyboard only)
This function allows you to instantly freeze a moving image.
This is useful when you want to display a still image from a
computer or video, giving you more time to explain the image
to the audience. You can also use this function to display a still
image from a computer while you make preparations for the
next computer images to be presented.
Ceiling+Rear
Reversed and inverted image
1. Press D-Freeze to freeze the image.
2. Press D-Freeze again to return to the moving image.
1. Press Menu.
2. Press 1 / 2 to select ‘PRJ Mode’.
3. Press 3 / 4 to select the desired projection mode.
4. Press OK to save the setting.
5. To exit from the GUI, press Menu.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
9. OTHER SETTINGS
DIGITAL IMAGE MAGNIFICATION (D-ZOOM)
PICTURE DISPLAY MODE (V-FORMAT)
This function allows you to magnify a specific portion of an
image. This is useful when you want to display a detailed
portion of the image.
(on projector keyboard only)
This function allows you to modify or customise the picture
display mode to enhance the input image.
Depending on the input signal,you can choose NORMAL,FIT
1. Press D-Zoom. Each time D-Zoom is pressed, the image will TO SCREEN,DOT BY DOT,WIDE or NORMAL (WIDE)image.
be magnified.
– Each time V-Format is pressed, the picture mode changes as
shown on the next page.
2. When the image is magnified, you can pan and scan around
the image by using 3 , 4 , 1 or 2.
Notes:
– "FIT TO SCREEN" is displayed only when SXGA signals that
are not in 4:3 aspect ratio are input.
– DOT BY DOT mode displays images in their native resolution
and not expanded to fit the LCD resolution.
AV MUTE FUNCTION
This function can be used for muting the sound of the
projector (or an external connected sound amplifier) and for
muting the picture.
Press A/V Mute.
– ‘AV Mute’ is displayed on the screen.
– Each time D-Zoom is pressed, image magnification toggles
as shown below.
x1
x2
x3
x4
x6
x8
– If the input signal is changed during digital image
magnification, the image will return to 1.
The input signal is changed:
• when Data 1, Data 2 or Video is pressed on the projector, or
Input on the remote control,
• when the input signal is interrupted, or
• when the input resolution and refresh rate changes.
To return to the original projected image, press A/V Mute
again.
TURNING OFF THE ON-SCREEN DISPLAY (OSD)
The On-screen Display (‘AV Mute’) that appears during mute
DIGITAL VIDEO EFFECT CORRECTION (V-EFFECT)
screen can be turned off. When ‘AV Mute Disp’ is set to
‘
’ in the GUI menu, ‘AV Mute’ will not be displayed during
(on projector keyboard only)
function.
– V-Effect is an image quality enhancement function that offers
a richer image by brightening the darker portions of the
image without altering the brightness of the brighter
portions.
1. Press Menu.
2. Press 1 / 2 to select ‘Options’.
– Two V-Effect settings are available to allow for differences in
the images played and in the brightness of the room.
– When you are watching images with frequent, dark scenes,
such as a film or concert, or when you are watching images
in a bright room, this feature makes the dark scenes easier
to see and gives the impression of greater depth in the
image.
V-Effect Modes
Selected Mode
V-Effect
V-Effect off
Standard picture without Video Effect
correction.
V-Effect on
Gives greater depth to darker portions of
image.
3. Press 3 / 4 to select ‘AV Mute Disp’.
•
Press V-Effect. Each time V-Effect is pressed, the V-Effect
level toggles as shown below.
4. Press 1 / 2 to select ‘
’ to turn on or ‘
’ to turn off
the function.
5. To exit from the GUI, press Menu.
V-EFFECT
V-EFFECT
OFF
ON
23
Download from Www.Somanuals.com. All Manuals Search And Download.
9. OTHER SETTINGS
Picture display mode
(V-Format) (on projector keyboard only)
DATA MODE
NORMAL
1024 x 768
1024 x 768
1024 x 768
960 x 768
FIT TO SCREEN
DOT BY DOT
800 x 600
1024 x 768
1600 x 1200
1280 x 1024
4:3 aspect ratio
SVGA (800 x 600)
–
–
–
XGA (1024 x 768)
UXGA (1600 x 1200)
SXGA (1280 x 1024)
Other aspect ratios
1024 x 768
VIDEO MODE
NORMAL
1024 x 768
1024 x 768
WIDE
NORMAL (WIDE)
768 X 576*
768 X 576*
768 X 576*
–
4:3
Letterbox
Squeeze
1024 x 576*
1024 x 576*
1024 x 576*
1024 x 576*
4:3 aspect ratio, 480I/P,
NTSC, PAL, SECAM
–
–
16:9 aspect ratio, 720P,
1080i
480I/P,720P,1080i
* The digital image shift function can be used with these picture display modes.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
9. OTHER SETTINGS
ON-SCREEN DISPLAY OVERRIDE FUNCTION
AUTOMATIC POWER SHUTOFF FUNCTION
This function allows you to turn off the on-screen messages
When no input signal is detected for more than 15 minutes,
the projector will automatically shut off. The on-screen
message on the left will appear five minutes before the power
is automatically turned off.
that appear during ‘input select’. Once ‘OSD Display’ is set to
‘
’ in the GUI menu, the on-screen messages will not
appear when Data 1, Data 2 or Video are pressed on the
projector or Input on the remote control.
1. Press Menu.
2. Press 1 / 2 to select ‘Options’.
3. Press 3 / 4 to select ‘OSD Display’.
Description of Automatic Power Shutoff
Power automattically shuts off after 15 minutes
of no signal input
Automatic Power Shutoff disabled
1. Press Menu.
2. Press 1 / 2 to select ‘Options’.
4. Press 1 / 2 to select ‘
’ to turn on or ‘
’ to turn off
the On-Screen Display.
5. To exit from the GUI, press Menu.
ECONOMY MODE
This function allows you to reduce the power consumption
when the projector is in Standby mode.
MONITOR OUT / RS232C OFF FUNCTION
This projector consumes power when using a monitor
connected to the Data out port for Data in 1, 2 and a computer
connected to the RS232C port. When not using these ports,
‘MNTR Out/RS232C’ can be set to ‘ ’ to reduce standby
power consumption.
3. Press 3 / 4 to select ‘Auto Power Off’.
4. Press 3 / 4 to select the ‘ ’ or ‘ ’.
5. To exit from the GUI, press Menu.
Description of Monitor Out/RS-232C Off
Standby power for Monitor Out/RS-232C
connection turned off
Note:
‘Auto Power Off’ is factory preset to ‘
’, and ‘MNTR
Out/RS232C’ is factory preset to ‘
’.
Monitor Out/RS-232C on
PASSWORD
A password can be set by the user and used with the keylock
level to prevent adjustments to certain settings on the GUI
1. Press Menu.
2. Press 1 / 2 to select ‘Options’.
Setting the Password
1. Press Menu.
2. Press 1 / 2 to select ‘Options’.
3. Press 3 / 4 to select ‘Password’, and then press 2.
3. Press 3 / 4 to select ‘MNTR Out/RS232C’, and then
press 2.
4. Press 3 / 4 to select ‘ ’ or ‘ ’.
5. To exit from the GUI, press Menu.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
9. OTHER SETTINGS
Notes:
– To cancel the keylock level, perform the above procedure
using the remote control.
– If a password has been set and the keylock level selected,
the password must be entered before adjusting the
keylock level.
CHECKING THE LAMP USAGE TIME
This function allows you to check the accumulated lamp usage
time.
1. Press Menu.
2. Press 1 / 2 to select ‘Options’. The lamp usage time will be
displayed.
4. Enter the new password using 3 / 4 to select the desired
number, and then press 2 to select the next digit. Continue
this procedure for the remaining three digits, and then press
OK.
5. Enter the password again (‘Reconfirm’) using 1/2/3/4, and
then press OK
6. To exit from the GUI, press Menu.
Note:
After setting the password, be sure to write it down in a secure
location so as not to forget it.
–
It is recommended that the lamp be replaced after
approximately 900 hours of usage. See page 29-30 for
details.
Changing the Password
1. Follow steps 1 to 3 in ‘Setting the Password’ above.
2. Enter the old password using 1/2/3/4, and then press OK.
3. Enter the new password using 1/2/3/4, and then press OK.
4. Enter the password again (‘Reconfirm’) using 1/2/3/4, and
then press OK.
Note:
After 1000 hrs of usage, the projector will not be able to turn
on (it will go off if it is in use).
5. To exit from the GUI, press Menu.
CHECKING THE INPUT SIGNAL
SELECTING THE KEYLOCK LEVEL
1. Press Menu.
This function can be used to lock the use of certain operation
buttons on the projector. The user can still operate the
projector fully with the remote control.
2. Press 1 / 2 to select ‘Fine Sync’.
3. Press 3 / 4 to select ‘Signal Info’ to display the current
input signal.
Description of Keylock Levels
Normal:
All operation buttons are functioning.
Level A:
Only Data 1, Data 2, Video, Volume, AV Mute buttons on
the projector function.
Level B:
All operation buttons on the projector do not function.
1. Press Menu.
2. Press 1 / 2 to select ‘Options’.
3. Press 3 / 4 to select ‘Keylock Level’, and then press 2
4. To exit from the GUI, press Menu.
SETTING A BACKGROUND IMAGE
This function allows you to select the image displayed when no
signal is being sent to the projector.
Description of Background Images
Selected item
Background image
Philips
Blue
None
PHILIPS default image
Blue screen
Black screen
4. Press 3 / 4 to select the desired level
5. To exit from the GUI, press Menu.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
9. OTHER SETTINGS
1. Press Menu.
STATUS FUNCTION
2. Press 1 / 2 to select ‘Options’.
3. Press 3 / 4 to select ‘Background’, and then press 2.
This function can be used to display all the adjusted settings
on the screen simultaneously.
1. Press Menu .
2. Press 1 / 2 to select ‘Status’.
3. Press OK to display all the adjusted settings.
4. Press 3 / 4 to select the background image you want to
display on the screen.
5. Press OK to save the setting.
6. To exit from the GUI, press Menu.
SELECTING A STARTUP IMAGE
–
This function allows you to specify the image to be
displayed upon the projector’s startup.
Description of Startup Images
Selected item
Background image
4. To exit from the GUI,press Menu .
Philips
None
PHILIPS default image
Black screen
1. Press Menu.
2. Press 1 / 2 to select ‘Options’.
3. Press 3 / 4 to select ‘Startup Image’, and then press 2.
4. Press 3 / 4 to select the startup image you want to display
on the screen.
5. Press OK to save the setting.
6. To exit from the GUI, press Menu.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
10. MENU TREE
DATA MODE
MAIN MENU
VIDEO MODE
MAIN MENU
Picture
Contrast
Bright
Color(Compo.input only) -30 +30
Tint(Compo.input only) -30 +30
Sharp(Compo.input only) -30 +30
Red
Blue
CLR Temp
Reset
Signal Type
-30 +30
-30 +30
Picture
Contrast
Bright
Color
Tint
Sharp
Red
Blue
-30 +30
-30 +30
-30 +30
-30 +30
-30 +30
-30 +30
-30 +30
-30 +30
-30 +30
-3 +3
Reset
I/P Conversion
Computer-RGB
Component
Interlaced
Interlaced
Progressive
I/P Conversion
Progressive
Audio
Volume
Balance
Treble
Bass
-30 +30
-30 +30
-30 +30
Fine Sync
Clock
-150+150
-60+60
-150+150
-60+60
Phase
H-Pos
Reset
V-Pos
Reset
Save Setting
Select Setting
Special Modes
….
….
Options
Lamp Timer
AV mute Disp
OSD Display
Video System
[ON/OFF]
[ON/OFF]
Auto
PAL(50Hz/60HZ)
SECAM
1024 x 864
1152 x 864
1152 x 870
1152 x 882
Resolution 640x480
Hor Freq
Vert Freq
[ON/OFF]
[ON/OFF]
Signal Info
NTSC4.43
NTSC3.58
Philips
Background
Auto Sync
Auto Sync Disp
Blue
None
Startup Image
Philips
None
MNTR Out/RS232C
Auto Power Off
Key Lock Level
[ON/OFF]
[ON/OFF]
Normal
Audio
Volume
Balance
Treble
Bass
-30 +30
-30 +30
-30 +30
Level A
Level B
Reset
Password
Old Password
New Password
Reconfirm
Options
Lamp Timer
AV mute Disp
OSD Display
Background
[ON/OFF]
[ON/OFF]
Philips
Blue
Language
English
Deutsch
Espanol
Nederlands
Francais
Italiano
None
Startup Image
Philips
None
Svenska
Portugues
MNTR Out/RS232C
Auto Power Off
Key Lock Level
[ON/OFF]
[ON/OFF]
Normal
PRJ Mode
Status
Front
Level A
Ceiling + Front
Rear
Level B
Password
Old Password
New Password
Reconfirm
Ceiling + Rear
Language
English
Deutsch
Espanol
Nederlands
Francais
Italiano
Svenska
Portugues
PRJ Mode
Status
Front
Ceiling + Front
Rear
Ceiling + Rear
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting RS-232C port/Maintenance
11. ADDITIONAL INFORMATION
CONNECTING RS-232C PORT
When the RS-232C port on the projector is connected to a
computer with an RS-232C cable (cross type, sold separately),
the computer can be used to control the projector and check
the status of the projector.
1. Connect the supplied DIN-D-sub RS-232C cable to the RS-
232C port on the projector.
2. Connect a RS-232C cable (sold separately) to the other end
of DIN-D-sub RS-232C cable and to the serial port on the
computer. See page 14 for details.
4. Clean the air filter. Clean the dust off the air filter and cover
with a vacuum cleaner extension hose.
5. Replace the air filter. Place the air filter underneath the tabs
on the filter frame.
CAUTION!
– Do not connect or remove RS-232C cable to or from the
computer while it is on. This may damage your computer.
– The wireless mouse or RS-232C function may not operate if
your computer port is not correctly set up. Please refer to
the operation manual of the computer for details on setting
up/installing the correct mouse driver.
– A Macintosh adapter may be required for use with some
Macintosh computers. Contact your nearest Philips
Authorised LCD Projector Dealer or Service Centre.
– For more details on specification of the use of the RS-232C
please contact your nearest Philips Authorised LCD projector
Dealer or Service Centre.
6. Replace the filter cover. Insert the tab on the end of the
filter cover into the filter cover opening and press the filter
cover into position.
AIR FILTER MAINTENANCE
• This projector is equipped with two air filters to ensure the
optimal operating condition of the projector.
• The air filters should be cleaned every 100 hours of use.
Clean the filters more often when the projector is used in a
dusty or smoky location.
• Have your nearest Philips Authorised LCD Projector Dealer
or Service Centre exchange the filter when it is no longer
possible to clean it.
Note:
Cleaning and replacing the bottom air filter
1. Unplug the powercord.
2. Remove the bottom filter cover.
Be sure the filter cover is securely installed. The power will not
turn on unless it is correctly installed.
– Turn over the projector. Press the tab and lift open the filter
cover in the direction of the arrow.
Cleaning the side air filter (not removable)
If dust or dirt has collected inside the air filter, clean the filter
with a vacuum cleaner extension hose.
Air
filter
Air filter
(not removable)
)
Note:
The side air filter cannot be removed.
LAMP MAINTENANCE
Lamp/Maintenance Indicators
• The warning lights on the projector indicate problems inside
the projector.
• There are two warning lights: a temperature warning
indicator (Temp.) which warns that the projector is too hot,
and a Lamp indicator (Lamp) which lets you know when to
change the lamp.
3. Remove the air filter.
– Grasp the air filter between your fingers and lift it out of the
filter cover.
• If a problem occurs, either the Temperature warning
indicator or the Lamp indicator will light up red. After turning
off the power, follow the procedures given in the next table.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
11. ADDITIONAL INFORMATION
Maintenance Indicator
TEMPERATURE
WARNING indicator.
Condition
Problem
Possible Solution
The internal temperature is • Blocked air intake.
abnormally high.
• Relocate the projector to an area with
proper ventilation.
• Clogged air filter.
• Clean the filter. (See page 29.)
• Cooling fan breakdown.
• Internal circuit failure.
• Take the projector to your nearest Philips
Authorized LCD Projector Dealer or
Service Center for repair.
LAMP REPLACE-
MENT indicator.
The lamp does not light up. • Burnt-out lamp.
• Carefully replace the lamp.(See pages 30
and 31.)
• Take the projector to your nearest
Authorized Sharp Industrial LCD Products
Dealer or Service Center for repair.
• Lamp circuit failure.
The lamp requires
replacement.
• Lamp has been used for
over 900 hours.
POWER indicator.
The POWER indicator
flashes in red when the
projector is on.
• The bottom filter cover is
open.
•Securely install the bottom filter cover.
Condition
Problem
Possible Solution
The LAMP REPLACEMENT indicator lights up •Lamp has been used for over
•Purchase a replacement lamp unit
(lamp/cage module)of the current type
LCA 3112 (8670 931 12009) from your
nearest Philips Authorized LCD Projector
Dealer or Service Center.
•Replace the lamp.(See pages 30 and 31.)If
you wish,you may have the lamp replaced
at your nearest Philips Authorized LCD
Projector Dealer or Service Center.
red, and ‘LAMP‘ and ‘ ’ will flash in yellow
in the lower-left corner of the picture.
A significant deterioration of the picture and
color quality occurs.
900 hours.
The power will automatically turn off and the •Lamp has been used for over
projector will enter standby mode.
‘LAMP‘ and ‘ ’ will flash in red in the lower-
left corner of the picture, and the power will
turn off.
1,000 hours.
Notes:
Replacing the lamp
– If the Temperature warning indicator lights up, follow the
above possible solutions and then wait until the projector
has cooled down completely before turning the power back
on. (At least 5 minutes.)
1. Turn off the power.
– Press Power OFF. Wait until the cooling fan stops.
2. Disconnect the powercord.
– Unplug the powercord from the AC socket and unplug all
the other cables.
3. Slide the lamp cage cover out.
– Turn over the projector and unfasten the user service screw
that secures the lamp cage cover. Then slide the cover in
the direction of the arrow.
– If the power is turned off and then turned on again, as during
a brief rest, the Lamp indicator may be triggered, preventing
the power from going on. Should this occur, take the
powercord out of the wall outlet and put it back in again.
Lamp (LCA 3112; 8670 931 12009)
The lamp in this projector operates for approximately 1,000
cumulative hours, depending on the usage environment. It is
recommended that the lamp be replaced after 900 cumulative
hours of use or when you notice a significant deterioration of
the picture and color quality. The lamp usage time can be
checked with the On-screen Display (see page 26). Carefully
change the lamp by following the steps under ‘Replacing the
lamp’.
If the new lamp does not light after replacement, take your
projector to the nearest Philips Authorized LCD Projector
Dealer or Service Center for repair. Purchase a replacement
lamp unit (lamp/cage module) of the current type
LCA 3112; 8670 931 12009 from your nearest Philips
Authorized LCD Products Dealer or Service Center.
Then carefully change the lamp by following the instructions
below. If you wish, you may have the lamp replaced at your
nearest Philips Authorized LCD Projector Dealer or Service
Center.
4. Remove the lamp cage.
– Remove the securing screws from the lamp cage.
Hold the lamp cage by the handle and pull it towards you.
Securing screws
CAUTION!
– Intense light hazard. Do not attempt to look into the aperture
and lens while the projector is operating.
– As the usage environment can vary significantly, the
projector lamp may not operate for 1000 hours.
5. Replace the lamp cage.
– Press the lamp cage firmly into the lamp cage
compartment. Fasten the securing screws.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
11. ADDITIONAL INFORMATION
CAUTION!
– To avoid injury to yourself and damage to the lamp, be sure
to carefully follow each steps under ‘Replacing the lamp’.
– Before or after replacing the lamp, be sure to clean the air
filters. See page 29 for cleaning the air filters.
Resetting the lamp timer
1. Connect the powercord.
– Plug the powercord into the AC socket of the projector.
2. While pressing 4, 2 and OK on the projector, press Power
ON on the projector.
– ‘Lamp 0000H’ is displayed, indicating that the lamp timer is
reset.
6. Slide the lamp cage cover in.
–
Slide the lamp cage cover in the direcrtion of the arrow.
Then fasten the user service screw.
Note:
Be sure the lamp timer is reset after replacing the lamp.
If not reset, the projector does not recognize the lamp
replacement and the previous status remains unchanged.
KENSINGTON LOCK
This projector has a Kensington Security Standard slot for use
with a Kensington Micro Saver Security System. Refer to the
information that came with the system for instructions on how
to use it to secure the projector.
CAUTION!
– Do not remove the lamp cage directly after operation of the
projector. The lamp may be extremely hot. Wait at least one
hour after the powercord is disconnected to allow the
surface of the lamp cage to fully cool before removing the
lamp cage.
– Be sure to remove the lamp cage by the handle. Be sure not
to touch the glass surface of the lamp cage or the inside of
the projector.
Kensington
Security
)
Standard connector
31
Download from Www.Somanuals.com. All Manuals Search And Download.
12. TROUBLESHOOTING
If a fault occurs, first check the points listed below before taking the projector for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service organisation.
WARNING
Under no circumstances should you try to repair the projector yourself as this could invalidate the warranty.
PROBLEM
480P IMAGES DO NOT APPEAR
• CHECK
• Set the resolution mode to 480P. (See page 17)
NO PICTURE AND NO SOUND.
AN UNUSUAL SOUND IS OCCASIONALLY HEARD FROM
THE CABINET
• Projector powercord is not plugged into the wall outlet.
• The bottom filter cover is not securely installed.
• Selected input is wrong. (See pages 15)
• Cables improperly connected to rear panel of the projector.
(See pages 12-14)
• If the picture is normal, the sound is due to cabinet
shrinkage caused by temperature changes.
This will not affect operation or performance.
• Remote control batteries have run down. (See page 10)
• On-screen Display (‘AV-MUTE’) is turned off and AV-Mute
function is turned on, creating a black image. (See page 23)
MAINTENANCE INDICATOR LIGHTS UP
• Refer to ‘Lamp/Maintenance Indicators’ on page 29-30.
AFTER REPLACING LAMP, THE PREVIOUS STATUS
REMAINS UNCHANGED.
POWER CANNOT BE TURNED ON OR OFF USING THE
POWER BUTTONS (ON/OFF) OF THE PROJECTOR
• Reset the lamp timer. (See page 31)
• Keylock level is set to "Level A" or "Level B", preventing
operation of some or all buttons (See page 26)
LENS COMES OFF
SOUND IS HEARD BUT NO PICTURE APPEARS
• Align the mark on the lens with the corresponding mark on
the projector, push the lens firmly in place, and rotate to the
right.
• Cables improperly connected to rear panel of the projector.
(See pages 12-14)
•’Contrast’ and ‘Bright’ adjustments are set to minimum
position. (See page 19)
PICTURE APPEARS BUT NO SOUND IS HEARD
• Cables improperly connected to rear panel of the projector.
(See pages 12-14)
• Volume is set to minimum. (See page 20)
COLOUR IS FADED OR POOR
•’Color’ and ‘Tint’ adjustments are not correct.
(See page 19)
COLOUR IS DISTORTED (EXCEPT FOR VIDEO MODE)
• Change the input signal type. (See page 15)
PICTURE IS BLURRED
• Adjust the focus. (See page 10)
• Projection distance is too long or too short to allow for
proper focus. (See page 9)
PICTURE NOISE APPEARS
• Adjust the phase setting. (See page 18)
• Noise may appear when used with certain computers.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
|