Philips Multimedia projector
cBright Series
LC4345, LC4341, LC4331
b
y
S
a t
n
d
R
C
L
M
a
m
u
t
e
p
A
V
V
o
u l
m
K
e
e
y
s
t
o
n
e
M
e
n
u
O
K
User guide
English
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
2. Things You Should Know
Table of contents
Note: This equipment has been tested to comply with the limits
for a class A digital device in accordance with Part 15 of
the FCC Rules as well as the European CE marking.
0. Controls and connections .....................................................2
1. Introduction............................................................................3
Table of contents .....................................................................3
Introduction .............................................................................3
Packaging contents .................................................................3
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
2. Things You Should Know ....................................................3
3. Im portant Safeguards ...........................................................4
4. Projector Features .................................................................5
These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment.
5. Functional Overview ..........................................................6-7
Controls ...................................................................................6
Connections .............................................................................7
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
user’s guide, may cause harmful interference to radio
communications.
6. Set Up..................................................................................8-9
Positioning the projector and screen.......................................8
Mains supply ...........................................................................8
Adjusting the focus and size of the image ..............................8
Adjusting the vertical and horizontal angle of the projector....8
Moving the projector ...............................................................9
Inserting the batteries in the compact remote control ...........9
Inserting the batteries in the trackball remote control............9
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
7. Installation ..................................................................... 10-14
Video/computer cables and adapter ......................................10
Connecting to a computer.....................................................11
Connecting to video equipment ............................................12
Connecting to audio equipment ............................................13
Connecting to an external monitor........................................14
–
–
–
Reorientate or relocate the receiving antenna.
Increase the distance between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
8. Operation ....................................................................... 15-19
Preparation .......................................................................15-16
Display and Picture control...............................................16-18
Audio control .........................................................................18
Other settings........................................................................19
–
FCC Warning:
To assure continued compliance, use only the provided grounded
power supply cord and shielded interface cables when
connecting this device to a computer. Also, any unauthorized
changes or modifications to this equipment could void the user’s
authority to operate this device.
9. Maintenance .................................................................. 20-22
Cleaning .................................................................................20
Cleaning the dustfilter ...........................................................20
Maintenance of the trackball remote control ........................20
Lamp......................................................................................21
Lamp replacement.................................................................21
Resetting the lamplife time ...................................................22
Note: Save energy! Please put the projector in the STANDBY
position if you are not going to use the projector for more
than 15 minutes.
10. Troubleshooting...................................................................23
Im portant note for users in the U.S.A.
Introduction
The responsible party of this multi media projector is the
following:
Congratulations on your purchase of one of the most
sophisticated and reliable products on the market today. We are
sure that, used properly, it will bring you years of enjoyment. You
will want to keep this manual handy, as it is a convenient source
of information about your projector. For your own protection and
prolonged operation of your projector, please read the ‘Important
Safeguards’ section before use.
Philips Consumer Electronics Company
One Philips Drive
Knoxville, TN 37914
Telephone (1888) 873-4672
Packaging contents
Please confirm that the following items are packed in the
projector box. They are provided to help you use or set up your
projector.
–
–
–
–
–
–
–
–
–
Projector
Mains lead
Audio/Video RCA Cable
Scart/RCA Audio Video adapter (not for USA version)
Remote control + batteries
Soft bag
Integrated VGA/USB cable
User Guide, Projection Assistant and more on CD-ROM
Quick set up Card
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Im portant Safeguards
14. Do not overload wall outlets and extension cords with too
many products, because this can cause a fire or electric
shock.
Please read all of these instructions
before you operate your projector.
SCAUTION:
15. Never push objects of any kind into the projector through
cabinet slots as they may touch dangerous voltage points or
short cut parts, which could result in a fire or electric shock.
16. Do not attempt to service the projector yourself other than
maintenance issues presented in chapter ‘Maintenance’.
Opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.
Save these instructions for future
reference.
Electrical energy can perform many useful functions.
This projector has been engineered and manufactured to meet
applicable safety standards. IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order
not to defeat the safeguards incorporated into this projector,
observe the following basic rules for its installation, use and
servicing.
17. Unplug the projector from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
A. When the power cord or plug is damaged or frayed.
B.
C.
If liquid has been spilled into the projector.
If the projector has been exposed to rain or water.
D. If the projector does not operate normally when you
follow the operating instructions. Adjust only those
controls that are covered by the operating instructions;
improper adjustment of other controls may cause
damage and will often require extensive work by a
qualified technician to restore the projector to normal
operation.
1. Unplug the projector from the wall outlet before cleaning or
lamp replacement.
2. Do not use liquid cleaners or aerosol cleaners. Use a soft dry
cloth to clean the projector unit. If the unit is very dirty, wet a
cloth with neutral detergent, squeeze it tight, wipe the unit
with it, and finish by wiping with a dry cloth.
Do not use a chemical duster or polisher-cleaner because it
can adversely affect the unit and peel the paint.
3. Do not use attachments not recommended by PHILIPS, as
they may cause hazards.
E.
If the projector has been dropped or the cabinet has
been damaged.
F.
When the projector exhibits a distinct change in
performance – (this indicates a need for service).
4. Do not use the projector near water- for example, near a
bathtub, washbowl, kitchen sink, or laundry tub, in a wet
basement, near a swimming pool, etc. Never spill liquid into
the projector.
5. Do not place the projector on an unstable cart, stand, or
table. The projector may fall, which may cause serious injury
to a child or an adult and/or serious damage to the unit. Use
only with a cart or stand recommended by its manufacturer
as being suitable for use with a projector.
6. Ceiling, wall or shelf mounting should be done with a
mounting kit approved by the manufacturer for use with a
projector and should follow the manufacturer’s instructions.
7. Projector equipment and cart combinations should be moved
with care. Quick stops, excessive force, and uneven surfaces
may cause the equipment and cart combination to overturn.
8. Slots and openings of the cabinet are provided for ventilation.
To ensure reliable operation of the projector and to protect it
from overheating, these openings must not be blocked or
covered. These openings should never be covered with cloth
or other material. The bottom opening should not be blocked
by placing the projector on a bed, sofa, rug, or other similar
surface. The projector should not be placed near or over a
radiator or heating vent. The projector should not be placed in
a built-in installation such as a bookcase unless proper
ventilation is provided.
18. Upon completion of any service or repairs to the projector,
ask the service technician to perform a routine safety check
to check that the projector is in safe operating condition.
19. When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original parts. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
20. It is recommended to clean the air filter after every 100 lamp
hours. The projector may become too hot if the filter is not
cleaned when required.
21. If the lens becomes dirty or smudged, clean it with a clean,
dampened cloth. Never touch the lens with your fingers.
22. Do not look directly into the aperture and lens while
operating the projector as this may damage your eyes.
9. The projector should be operated only from the type of
power source indicated on the side of the projector or in the
specifications and with the appropriate mains lead. If you are
not sure of the type of power supplied to your business or
the right type of mains lead, consult your projector dealer or
local power company.
10. Do not allow anything to rest on the power cord. Do not
place the projector where the cord will be walked on.
11. Follow all warnings and instructions marked on the projector.
12. As a safety feature, this projector is equipped with mains
lead with a 3-pin grounded plug (for USA-versions only) or a
2-pin grounded plug (for European versions only). The 3-pin/2-
pin grounded plug will fit only into a grounding type power
outlet. If the plug does not fit, use an adapter that is properly
grounded or have an electrician install a grounded type
outlet. Do not attempt to modify this AC plug.
13. For added protection of the projector during a lightning
storm, or when it is left unattended or not in use for long
periods of time, unplug it from the wall outlet and disconnect
any cable systems. This will prevent damage to the projector
due to lightning and power-line surges.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Projector Features
1. Keystone Correction
8. Excellent video quality
A keystoned image (picture top width larger than picture
bottom width or vice versa) appears when the relative
positions of the projector and the screen are not correct.
With the ‘keystone correction’ feature you can correct this
picture distortion. Digital keystone correction is directly
accessible via the keyboard on the projector or via the
‘Display’ submenu of the On Screen Display menu.
The projector accepts the input signal of all major video
formats, including PAL, SECAM, NTSC and S-Video signals.
The projector will recognize these standards and adapt to
them automatically. With the ‘picture format’ feature you can
select one of three picture format options 4:3, 16:9 or 16:9
enlarged.
9. Stereo Audio Output
2. Auto Im age
Line output for connecting external audio equipment via
standard 3.5 mm stereo jack.
The ‘Auto Image’ feature automatically sizes and positions
the image, to optimally fit the screen picture. It is applicable
for data input only and accessible in the ‘Display’ submenu of
the On Screen Display menu. Manual settings of Horizontal
Size, Shift and Phase remain possible by switching Auto
Image off. The projector is fully PC and MAC compatible.
10. Adjustable Screen Capability
The diagonal picture size of the display can be set from
21" (0.53 m) to 262" (6.6 m).
11. Ceiling Mount and Rear Screen projection
The projector is equipped with a full mirror scan conversion
function (‘vertical/horizontal mirror’), which allows the image
to be reversed for ceiling mount as well as for rear projection
applications.
3. USB
The USB (Universal Serial Bus) connector allows you to
connect to computers equipped with a USB interface,
resulting in real hot plug and play presentation. By
connecting USB, the mouse function on the Remote Control
automatically gets installed.
4. Digital features
The digital features of the projector are of great value for an
attractive presentation. With ‘digital zoom’ a specific part of
the projected image can be enlarged. The ‘digital freeze’
feature enables you to capture moving pictures (still picture).
5. Very easy to install and operate
The OSD (On Screen Display) information screens and
menus in 6 languages provide you with additional information
to help you make the right choices about installation and
operation, and to perform the correct actions.
The standard OSD language is English. In addition you can
select French, Spanish, German, Italian and Portuguese.
The sensor of the wireless remote control allows you to
operate both your computer as well as your projector from
almost anywhere in the room. The directional shuttle on
the projector and on the com pact rem ote control function
as Cursor Control and are used to manipulate the mouse
cursor on the connected computer, as long as the menu is
not active. On the trackball rem ote control (standard with
models LC4345 and available as accessory for the other
models) the trackball is used to manipulate the mouse
cursor. When the menu is active, the Cursor Control controls
the menu cursor.
The local keyboard provides direct access buttons for those
functions that are most often used during set-up of the
projector. The remote control provides buttons for those
functions that are most often used during presentations. For
a complete overview of keyboard and remote control
buttons, see the Functional Overview in the next paragraph.
6. External m onitor connection
A separate external monitor (or a second projector) can be
connected to the projector, The image projected is
simultaneously shown on the monitor.
7. High reliability and excellent brightness
The Philips UHP lamp guarantees long life, excellent
brightness over the lamp’s lifetime and excellent colour
reproduction.
Furthermore, the projector has an excellent brightness- and
colour uniformity over the entire picture.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Functional Overview
See illustrations
Controls
On projector (fig. 1)
On com pact rem ote control (LC4341/ 4331) - (fig. 2)
1 Menu
1 Stand by On
To activate and deactivate the menu.
To switch the projector in or out the the power standby
mode.
2 Cursor Control
To manipulate the mouse cursor on the connected computer
as long as the menu is not active. When the menu is active
the Cursor Control controls the menu cursor. The cursor
control works with up/down and left/right button operation.
2 Mouse Left/ Right
Function as the Left and Right mouse buttons of your PC.
3 – Volum e +
To adjust the volume.
Notes:
– The Cursor Control can only function as a mouse cursor
when the USB socket of the projector is connected to the
USB downstream terminal of the computer.
– When the Digital Zoom is active, the Cursor Control gives
direct access to the Panning function to select the enlarged
area.
4 Menu
To activate and de-activating the menu.
5 Mute
To mute the sound of the projector (or an externally
connected sound amplifier).
3 A(udio)/ V(ideo)-Mute
6 Source
To mute the sound of the projector (or an externally
connected sound amplifier) and to mute the picture.
To select the current projection source (Data, S-Video or
Video). The button toggles between the three signals.
4 Standby On
7 D(igital)-Freeze
To switch the projector in or out of the power standby mode.
When the projector is in standby mode, the ring around the
button lights up red. When the projector is operating, the ring
is white.
To capture a moving picture. The button toggles between the
Freeze mode and the display situation.
8 D(igital)-Zoom
To switch the Digital Zoom function ‘On’ or ‘Off’ (toggle
button). In ‘On’ condition, the image is magnified with the
zoom factor chosen under Magnification in the menu and the
Cursor Control can be used to select the enlarged area
(Panning).
5 OK
To confirm actions in the menu when the menu is on screen.
6 Source
To select the current projection source (Data, S-Video or
Video). The button toggles between the three signals.
9 A(udio)/V(ideo) Mute
To mute the sound of the projector (or an externally
connected sound amplifier) and to mute the picture.
7
Keystone
To correct picture distortion of the vertical keystone type by
digital scaling.
0 Cursor Control
To manipulate the mouse cursor on the connected computer
as long as the menu is not active. When the menu is active
the Cursor Control controls the menu cursor. The cursor
control works with up/down and left/right button operation.
8 Lam p indicator
– Slowly flashes green when the lamp is starting up
– Lights up green when the lamp is on
– Slowly flashes orange when the lamp is starting up and
lamp life expires within the next 100 hours or has expired
– Lights up orange when the lamp is on and lamp life expires
within the next 100 hours or has expired
Notes:
– The Cursor Control can only function as a mouse cursor
when the USB socket of the projector is connected to the
USB downstream terminal of the computer.
– When the Digital Zoom is active, the Cursor Control gives
direct access to the Panning function to select the enlarged
area.
– Lights up red when the lamp start has failed
9 R(emote) C(ontrol) indicator
Flashes green when the remote control is operated and the
projector responds.
! OK
0 Zoom ring
To confirm actions in the menu when the menu is on screen.
To adjust the size of the projected image.
! Focus ring
To adjust the focus of the projected image.
@ Height/ Level adjusters
To adjust the vertical and/or horizontal angle of the projector.
# Lens cap
To protect the lens when the projector is not in use.
$ IR sensor
To receive the signals from the remote control.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Functional Overview
See illustrations
Connections (fig. 4)
On trackball rem ote control (LC4345) - (fig. 3)
Data source connections
1 On/ off button
a
b
g
Audio out
To switch the remote control on and off.
Note: The remote control will always use some power, even
when not in use. Therefore it is advised to always
switch off the remote control after use.
Output socket to connect to the Line Input sockets of an
amplifier or stereo system.
USB (upstream)
Input socket to connect a PC or Apple Macintosh computer
equipped with a USB downlink connection.
2 Cursor Control
To manipulate the mouse cursor on the connected computer
as long as the menu is not active. When the menu is active
the Cursor Control controls the menu cursor.
Data in
Input socket to connect to the Data out terminal of a
computer.
Notes:
– The Cursor Control can only function as a mouse cursor
when the USB socket of the projector is connected to the
USB downstream terminal of the computer.
– When the Digital Zoom is active, the Cursor Control gives
direct access to the Panning function to select the enlarged
area.
Video source connections
a
c
d
Audio out
Output socket to connect to the Line Input sockets of an
amplifier or stereo system.
Audio in L/ R
3 OK
Input sockets to connect to the Audio out sockets of a video
recorder (S-VHS, PAL, NTSC, SECAM).
To confirm actions in the menu when the menu is on screen.
When the menu is not on screen the – / – – buttons
function as the Left and Right mouse buttons of your PC.
Video
Input socket to connect to the Video out socket of a video
recorder, Laser Disc player, video camera or TV with AV
output socket (PAL, NTSC, SECAM).
4 Menu
To activate and deactivate the menu.
5 Stand by On
e
S-Video
To switch the projector in or out the the power standby
mode.
Input socket to connect to the S-Video out socket of a S-VHS
video recorder, a VCR, Laser Disc player, video camera or TV
with AV output socket.
6 – Volum e +
To adjust the volume.
Other connections
7 Source
To select the current projection source (Data, S-Video or
Video). The button toggles between the three signals.
f
Data out
To connect to an external monitor (or a second projector).
The image projected is simultaneously shown on the
monitor.
8 D(igital)-Freeze
To capture a moving picture. The button toggles between the
‘Freeze’ mode and the normal display situation.
h
i
Lam p com partm ent
9 D(igital)-Zoom
Lock slit
To switch the Digital Zoom function ‘On’ or ‘Off’ (toggle
button). In ‘On’ condition, the image is magnified with the
zoom factor chosen under Magnification in the menu and the
Cursor Control can be used to select the enlarged area
(Panning).
To insert an optional locking device (Kensington lock).
j
Pow er
To connect the projector to the mains.
k
Dust filter
0 A(udio)/ V(ideo) Mute
To mute the sound of the projector (or an externally
connected sound amplifier) and to mute the picture.
! Back-light button
To switch on the button illumination.
The back-light will automatically switch off after 5 seconds.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Set Up
Positioning the projector and screen
•
Place the projector on a stable, level surface, out of direct
sunlight and away from sources of excessive dust, dirt, heat,
water, moisture, vibration and strong magnetic fields.
Face the projector towards the screen for the best picture
results. To determine the distance for the desired size,
please refer to the Projection Assistant, a calculation
programme included on the CD-ROM.
–
The Standby Warning
screen will appear for
20 seconds.
Warningꢀ
ꢀ
ꢀ
ꢀ
ꢀ
If the projector is switched off you have to waitꢀ
1 minute before you can switch on the projector ꢀ
again.ꢀ
ꢀ
ꢀ
ꢀ
•
•
The screen should be positioned so that it is not directly
touched by sunlight or artificial light, as this will wash out the
colours of the picture, making it hard to see.
The projector can be used for both front projection, rear
projection and ceiling projection applications. As default
factory setting, the projector has been set up for front
projection. You can change to rear or ceiling projection via the
OSD menu. See ‘Rear screen projection’ and ‘Ceiling-mount
projection’ under ‘Operation - Display and picture control’ for
further instructions.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
To switch off projector keep stand-by key pressedꢀ
for 3 seconds.ꢀ
Press OK key to remove this warning.
Note: The Stand by Warning screen can be removed by keeping
the Stand by On button pressed for 3 seconds.
If the Stand by On button is pressed for 3 seconds the
first time (step 3), the projector is switched back into the
power standby mode without the Standby Warning screen
being displayed.
•
•
Choose a screen size suitable for the number of viewers and
the size of the room.
Picture quality is best when you sit directly in front of the
projector screen.
Mains supply
5. To switch off the mains supply completely, pull the mains
1. Insert the mains lead into the projectors Power socket and
plug out of the wall socket.
connect it to the wall socket.
Note: Before disconnecting the mains lead, make sure that the
cooling fan has stopped (about 3 minutes after the
projector has been switched to Power Standby).
Note: The standby indicator lights up red, the projector is now in
the Power/Standby mode.
Adjusting the focus and size of the im age
y
b
S
d
n a t
R
C
L
M
m
a
u
p
e t
A
V
o
V
m
u l
K
e
y s e t
o
n
e
•
•
Use the Zoom ring to adjust the size of the image.
Use the Focus ring to adjust the focus of the image.
M
u
n e
O
K
y b
S
d
n a t
R
C
L
M
m
a
u
p
e t
A
V
V
o
m
u l
K
e
s
y e
o
t
n
e
M
n e
u
O
K
Zoom ring
Focus ring
2. Remove the lens cap.
3. Press the Stand by
On button to switch on
the projector.
–
The lamp indicator
flashes green.
When the projection
lamp is on, the lamp
indicator lights up green
while the lamp is
starting up and the start-
up screen appears for
several seconds.
Adjusting the vertical and horizontal angle of the projector
Vertical angle
–
•
Use the Height/Level Adjusters to adjust the vertical angle of
the projector as specified under ‘Positioning the projector and
screen’.
PHILIPS
Multimedia Projectors
4. Press the Stand by On
button again to switch
the projector back into
the power standby
mode.
A
A
B
B
To Raise:
•
–
Keep both adjusters (A) pressed and lift to raise the projector.
The projector feet (B) will come out.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Set Up
Inserting the batteries in the com pact rem ote control
(LC4341/ 4331)
To Low er:
•
Keep both adjusters (A) pressed and gently lower the
projector.
P u s h
•
Use the Focus Ring and Zoom Ring to readjust the focus and
size of the image.
Horizontal angle (horizon)
•
Adjust or correct a possible tilted picture by turning the
projector feet to the desired position.
1. Push and slide the lid in the direction of the arrow.
2. Install two ‘AAA’ batteries as indicated inside the battery
compartment.
3. Replace the lid and snap it into place.
Note: The maximum range of the remote control is
approximately 15 m (± 50 feet).
Inserting the batteries in the trackball rem ote control
(LC4345)
Up: turn the feet to the left.
Dow n: turn the feet to the right.
P u s h
•
Use the Focus Ring and Zoom Ring to readjust the focus and
size of the image.
Keystone correction
If projector and screen are not properly placed, the picture will
be distorted, producing a keystone image.
Keystone correction allows you to correct
picture distortion of the vertical keystone type
by internal scaling.
Keystoned Im age
•
•
•
Use the Keystone
Use the Keystone
This correction function also is accessible through the
‘Keystone Correction’ option in the ‘Display’ submenu of the
On Screen Display (OSD) menu. For details see the
explanation in ‘Display and Picture Control’.
button to widen the image.
button to narrow the image.
1. Push and slide the lid in the direction of the arrow.
2. Install three ‘AA’ batteries as indicated inside the battery
compartment.
3. Replace the lid and snap it into place.
Caution!
Do not mix old and new batteries (also never mix alkaline and
manganese batteries).
Moving the projector
1. Press the Stand by On button to put the projector in stand
by. The standby indicator lights up red.
2. Wait until the cooling fan has stopped (about 3 minutes after
the projector has been switched off) and disconnect the
mains lead and all other cables.
Note: The maximum range of the remote control is
approximately 20 m (± 65 feet).
3. Make sure the lens is turned back in to prevent damage to
the lens.
4. Put the lens cap back in place to prevent dust, dirt or other
contamination from harming or damaging the front of the
projector lens when moving the projector.
y
b
S
d
n a t
R
C
L
M
m
a
u
p
e t
A
V
o
V
m
u l
K
e
y s e t
o
n
e
M
u
n e
O
K
Note: Never place the projector on the side where the
connections are located.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Installation
Video/ com puter cables and adapter
CONNECTIONS
No.
1
CABLE/ ADAPTER
Projector side
Com puter/ AV products side
Integrated VGA/ USB Cable
Mini D-Sub
15P (m ale)
Mini D-Sub
15P (m ale)
USB connector
4P (fem ale)
USB connector
4P (fem ale)
2
3
RCA Audio Video Cable
RCA pin
(m ale) x 3
RCA pin
(m ale) x 3
Scart/ RCA-AV Adapter
(depending on region)
Video/ com puter cables and adapter
These accessories (1 to 3) are supplied with the product for
connecting the projector to computer/AV equipment.
The numbers in the left-hand column correspond with the
numbers in the connection diagrams on the following pages.
When connecting the projector to a Macintosh computer, a
programmable VGA/MAC adapter is available as an optional
Philips cable accessory.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Installation
Connecting to a com puter
Connecting to a com puter
Caution!
The data input is suitable for both Apple Macintosh
PC (Desk Top/ Lap Top)/
MACINTOSH (Desk Top/ Pow er Book/ Pow er Mac)
–
computers (Power Book and Power Mac) as well as for
IBM compatible PCs.
–
–
–
The data output of IBM compatible PCs can be connected
directly to the projector using standard data cables.
Apple Macintosh computers may need a conversion plug
(optional) added to the standard data cable.
The figures in brackets (1) correspond to the figures in the
accessories diagram.
(b)
(g)
Audio out
R
L
Audio in
L
R
Video
S-Video
Data out
Data in
The characters in brackets (a) correspond to the characters in
fig. 4 of ‘Controls and connections’.
USB connection
A USB interface is available via an upstream connector.
Projector
Mac/ PC
When the projector’s USB (upstream ) connector is connected
to a PC or an Apple Macintosh computer equipped with a USB
downlink connection, it will identify as a USB device.
It is possible to:
1
1
–
control the cursor of the computer via the projector remote
control,
–
play audio information from the computer via the projector
speaker,
and
the display settings of the computer will be changed to fit
the capability of the projector.
optional Philips
VGA/ MAC
adapter
–
USB
A
Data out
Data out
1. Connect the Data out terminal of the computer to the Data in
terminal (g) of the projector and secure the plugs by
tightening the thumb screws.
For this, use the VGA/USB cable (1) supplied.
When connecting the projector to a Macintosh computer use
the VGA/MAC adaptor (optional).
2. Connect the USB (upstream) socket (b) of the projector to
the USB downstream port of the computer.
For this, use the VGA/USB cable (1) supplied.
–
You can now manipulate the mouse cursor on the computer
and on the screen, using Cursor Control. Audio information
from the computer will be played via the projector speaker.
Note: If the mouse cursor does not react when moving the
cursor control on the remote control:
3. Check that the Remote Control indicator on the projector
flashes green when you move the trackball.
–
–
If it does not: Check that you have switched on the remote
control. If you have, check that the batteries are installed
properly and/or replace the batteries.
If it does: Make sure that the USB cable has been properly
connected.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Installation
Connecting to video equipm ent
Connecting to video equipm ent
Note: The figures in brackets (1) correspond to the figures in the
accessories diagram.
S-VHS
(c)
(e)
The characters in brackets (a) correspond to the
characters in fig. 4 of ‘Controls and connections’.
Audio out
USB
udio
Video
So
Data out
Data in
D
Da
Caution!
Always switch off the projector before making any connections.
PAL, NTSC, SECAM
(c)
(d)
Audio out
USB
R
L
udio in
Video
S-Video
Data out
Data in
Data in
Data out
Projector
(2)
(optional)
(3)
S-Video
Projector
(2)
Scart adapter
(not for USA
version)
S-Video
Video
out
R Audio L
out
VCR
(3)
1. Connect the S-Video out socket of a S-VHS video recorder,
Laser Disc player, video camera or TV to the S-Video socket
(e) of the projector.
For this use an (optional) S-vVideo connection cable.
2. Connect the Audio out L/R sockets of the S-VHS video
recorder, Laser Disc player, video camera or TV to the Audio
in L/R sockets (c) of the projector.
Scart adapter
(not for USA
version)
R Audio L
Video
out
L
R
out
VCR
For this, use the red and white audio connectors of the
audio/video connection cable.
1. Connect the Video out socket of a VCR, Laser Disc player,
video camera or TV to the Video socket (d) of the projector.
For this, use the video/audio connection cable (2) supplied.
2. Connect the Audio OUT L/R sockets of the VCR, Laser Disc
player, video camera or TV to the Audio in L/R sockets (c) of
the projector.
Insert the white plug into the L socket and the red plug into
the R socket.
In case your VCR, Laser Disc player, video cam era or TV is
equipped w ith a Scart connector (depending on region):
1. Connect the Scart/RCA Audio Video adapter (3) supplied to
the Scart connector of the VCR, Laser Disc player, video
camera or TV.
For this, use video/audio connection cable (2) supplied.
Insert the white plug into the L socket and the red plug into
the R socket.
2. Plug the audio/video connection cable (2) supplied into both
In case your VCR, Laser Disc player, video cam era or TV is
equipped w ith a Scart connector (depending on region):
1. Connect the Scart/RCA Audio Video adapter (3) supplied to
the Scart connector of the VCR, Laser Disc player, video
camera or TV.
the adapter and the Audio in L/R sockets (c) of the projector.
Insert the white plug into the L socket and the red plug into
the R socket.
3. Plug an (optional) S-Video connection cable into the VCR and
the S-Video socket (e) of the projector.
2. Plug the video/audio connection cable (2) supplied into both
the adapter and the Video (d) and Audio in L/R sockets (c) of
the projector.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Installation
Connecting to audio equipm ent
Connecting to audio equipm ent
Note: The characters in brackets (a) correspond to the
characters in fig. 4 of ‘Controls and connections’.
Caution!
Always switch off the projector before making any connections.
Always turn down the volume control of the connected amplifier
before switching it on, to prevent damage to the speakers.
(a)
Audiout
USB
R
L
Audio in
L
R
Video
S-Video
Data out
Data in
Projector
(optional)
Am plifier
udio
in
•
Connect the Audio in L/R sockets of an amplifier or stereo
system to the Audio out socket (a) of the projector.
Insert the white plug into the L socket and the red plug into
the R socket.
Note: When the projector is connected to an external audio
amplifier, you cannot control the volume via the projector
or the remote control. However, the sound can still be
muted via the projector or the remote control.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Installation
Connecting to an external m onitor
Connecting to an external m onitor
Note: The characters in brackets (a) correspond to characters in
fig. 4 of ‘Controls and connections’.
(optional)
Caution!
Always switch off PC, external monitor and projector before
making any connections.
Monitor cable
1. Connect the Data out terminal of the computer to the Data in
terminal (g) of the projector and secure the plugs by
tightening the thumb screws.
(g)
For this, use the VGA/USB cable (1) supplied.
When connecting the projector to a Macintosh computer use
the VGA/MAC adaptor (optional).
o in
L
R
Video
S-Video
Data out
Data in
2. Connect the Data out terminal (f) of the projector to the
external monitor and secure the plugs by tightening the
thumb screws.
For this, use an optional monitor cable.
To obtain the audio signal on the monitor instead of on the
projector:
•
Connect the Audio in sockets of the monitor to the Audio out
socket (a) of the projector.
Insert the white plug into the L socket and the red plug into
the R socket.
Projector
Mac/ PC
•
(1)
Some monitors have a single Audio in socket for which a
different audio connection cable with a 3.5 mm mini jack is
required.
Notes:
– One external monitor or projector can be connected at a time.
– For further details on the operation with
(optional)
On Screen Displays see chapter ‘8 Operation’.
USB
Audio out
Data out
Data out
14
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Operation
Preparation
Preparation
General
Some examples:
1. Press the Stand by On button to switch on the projector.
Dataꢀ
ꢀ
ꢀ
Videoꢀ
ꢀ
No signal
–
The lamp indicator
flashes green and the
start up screen appears
for several seconds.
When the average
–
lamplife time has almost
expired and less than
100 hours remain, the
message ‘Warning:
lamplife has almost
expired’ will be displayed
on the screen when
switching the projector
on. For this refer to the
section ‘Lamp’ under
‘Maintenance’
PHILIPS
Multimedia Projectors
Data selected as source.
Video selected as source, no
input signal.
S-Videoꢀ
ꢀ
A/V Muted
S-Videoꢀ
ꢀ
A/V Muted
–
When the lamp is on, the lamp indicator lights up green.
2. If you use the trackball rem ote control:
–
–
Set the ON/OFF switch of the remote control to ON in order
to switch on the remote control.
If required, press the light button of the remote control.
When this button is pressed, the button illumination is
switched on for 5 seconds. Every time one of the buttons is
pressed within these 5 seconds, the illumination time is
extended by a further 5 seconds.
3. Select the required source (Data, Video or S-Video) by
pressing the Source button.
4. Switch on the computer or start video playback.
–
A feedback message appears on the screen, indicating the
selected source.
S-Video selected as source.
A/V muted.
Video selected as source.
A/V muted.
Messages - General explanation
Messages are
On Screen Display m enu - General explanation
All video and data adjustments and settings (except A/V Mute)
are done via On Screen
displayed in the centre of
Fan errorꢀ
the screen. The problem is
described in the header of
the message display.
Suggestion(s) to solve the
problem are displayed in the
gray part of the message
display.
Displays and with help of
Menu, OK (–/ – –) and
Cursor Control on the
projector or the remote
ꢀ
Menubarꢀ
ꢀ
Submenuꢀ
Submenu highlightꢀ
ꢀ
ꢀ
ꢀ
The projector will switch off automatically.ꢀ
ꢀ
Please contact a service centre for repair.
control.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
These messages cannot be
suppressed.
ꢀ
ꢀ
Actionwindow
Feedback m essages
Feedback messages are displayed in the top right corner of the
screen. They are displayed when:
1. Press Menu.
–
The menu bar appears on the screen.
The first item
–
–
–
–
a signal comes up or goes down,
when an input source is changed
when Mute or A/V Mute is activated.
when the Auto image function is set to On.
is highlighted and its sub
menu is shown.
Displayꢀ
Picture
Audio
Settings
ꢀ
Digital Freezeꢀ
Digital Zoomꢀ
Depending on the
1
1
Magnificationꢀ
Pan...ꢀ
These messages will only be displayed when the menu option
Feedback is set to ‘On’ in the Settings menu. All messages, will
be removed automatically after 4 seconds.
selected source (Data,
Video or S-Video) some
options of the submenu
may be greyed out. This
indicates that these
functions:
Keystone correctionꢀ
Auto Imageꢀ
1
1
1
ꢀ
Horizontal size...ꢀ
Phaseꢀ
Shift...ꢀ
ꢀ
Off
On
ꢀ
ꢀ
ꢀ
– are not available in a
certain mode,
– have no function for
the selected source.
ꢀ
Auto Image is used to automatically adjustꢀ
Horizontal Size, Phase and Shift.
For exam ple:
–
Horizontal size under submenu Display when Auto image is
switched to ON.
–
Hue under submenu Picture when signaltype is not NTSC.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Operation
Preparation/ Display and picture control
2. Use Cursor Control left
and/or right to move the
cursor to any other item
in the menu bar.
Tip for Window s users:
To adjust size and phase correctly:
Displayꢀ
ꢀ
Brightnessꢀ
Contrastꢀ
Sharpnessꢀ
Hueꢀ
ꢀ
Audio
Settings
Picture
1. Select ‘Start’ and then ‘Shut down’.
2. Adjust the projectors size control, so that no vertical bars
are visible.
3. Now adjust the projectors phase control for maximum
brightness of the projected image.
Saturationꢀ
Colour temperatureꢀ
Picture formatꢀ
Mirror
4. Press ‘No’ in the Windows shutdown screen to cancel the
shutdown action.
Data and Video/ S-Video
For both data and Video/S-Video signal input, the following
adjustments can be made:
–
–
–
Digital Freeze
captures a moving picture (still picture);
Digital Zoom
enlarges a part of the picture;
Pan
selects another section of enlarged picture (in combination
with digital zoom);
Keystone Correction
corrects picture distortion of the vertical keystone type by
internal scaling;
Brightness
adjusts brightness of the displayed picture;
Contrast
adjusts the overall contrast intensity;
Sharpness
controls the contour impression of the picture;
Colour Tem perature
adjusts the overall picture impression from warm to cool;
Mirror
3. Select the sub menu item
to be adjusted using
Cursor Control up and/or
down.
4. Adjust the selected item
in the action window at
the bottom of the screen,
using Cursor Control left
and/or right.
5. Select the next item to
be adjusted in the sub
menu and adjust as
described above.
6. Press Menu to close the
On Screen Display.
Displayꢀ
ꢀ
Brightnessꢀ
Contrastꢀ
Sharpnessꢀ
Hueꢀ
Saturationꢀ
Colour temperatureꢀ
Picture formatꢀ
Mirrorꢀ
Picture
Audio
Settings
–
(b)
ꢀ
–
–
–
–
–
minꢀ
max
ꢀ
ꢀ
Move pointer left or right to adjust the contrast level.
ꢀ
Language selection
The projector can display menus in one of six different languages.
mirrors the picture for use of the projector in various positions
with respect to the user(s) and the projection screen (for
further explanation see ‘Display and picture control’ - ‘Mirror’).
1. Press Menu.
–
The menu bar appears on the screen.
2. Use Cursor Control to select Settings in the menu bar.
3. Use Cursor Control to select Language from the sub menu.
4. Use Cursor Control to select the required language in the
action window.
Video/ S-Video only
For Video/S-Video signal input, the following adjustments can be
made:
5. If required, select the next item to be adjusted or press Menu
to exit.
–
–
–
Hue (only for NTSC)
adjusts the tint of the projected image;
Saturation
adjusts the colour saturation of the projected image.
Picture Form at
selects one of three picture format options (4:3, 16:9 or 16:9
enlarged);
Display and picture control
The projector’s picture is set to standard specifications at the
factory. However, you can adjust the image to suit your own
preferences.
The projector will store the last used settings for every source. So
when you switch from one source to another, the settings of the
source switched from will be stored and the settings of the source
switched to will be recalled.
When the projector is switched off and on again the settings for
the selected source will be recalled again.
Data only
For data signal input, the following adjustments can be made:
–
–
–
–
Auto im age
automatically sizes and positions the image to fit optimally in
the screen picture;
Horizontal size
adjusts the computer image in a horizontal direction to make
the image completely fill the screen;
Shift
adjusts the computer image in horizontal and vertical direction
to centre it on the screen;
Phase
when connecting the projector to your PC for the first time, be
sure to adjust the phase control for optimal readability of the
projected text.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Operation
Display and picture control
Note: A(audio)/V(video)-m ute can only be selected with the
AV mute button on the projector or on the remote control.
A/V mute then appears on the screen.
Shift
The Shift function adjusts the computer image in horizontal and
vertical direction to center it on the screen. This function is only
active when Auto image is set to OFF.
For exam ple:
Dataꢀ
ꢀ
A/V Muted
1. Press Menu.
–
The menu bar appears
on the screen.
Displayꢀ
Picture
Audio
Settings
Display is highlighted
and its sub menu is
shown.
ꢀ
Digital Freezeꢀ
Digital Zoomꢀ
1
1
Magnificationꢀ
Pan...ꢀ
2. Use Cursor Control to
move the cursor to
Shift.
3. Press OK (–/ – –) to
activate Shift.
ꢀ
Keystone correctionꢀ
Auto Imageꢀ
1
1
1
ꢀ
ꢀ
ꢀ
ꢀ
Horizontal size...ꢀ
Phaseꢀ
Shift...ꢀ
Shift is used to adjust the position of the image.ꢀ
Confirm to activate Shift.ꢀ
ꢀ
The follow ing adjustm ents procedures follow a slightly
different sequence of actions, or m ay need som e further
explanation.
4. Use Cursor Control to
position the computer
image.
5. Press OK (–/ – –) to
confirm and store the
adjustment.
6. If required, select the
next item to be adjusted
or press MENU to exit.
Shift1111
Pan
To view an enlarged area of the projected picture the Pan
function is used. Panning is only possible when the picture is
enlarged with Digital Zoom. If the picture is not enlarged, the
panning option is greyed out. When the Digital Zoom is active,
the Cursor Control gives direct access to the Panning function.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
1. Press D(igital) Zoom to activate the Digital Zoom function.
ꢀ
2. Press Menu.
ꢀ
ꢀ
ꢀ
ꢀ
–
The menu bar will appear.
Display is highlighted and its sub menu is shown.
Move pointer to position the image.ꢀ
3. Select the required zoom factor under Magnification.
4. Use Cursor Control to move the cursor to Pan.
5. Press OK (–/ – –) to
Press OK key when done.
ꢀ
Panning1111
activate Pan.
6. Use Cursor Control to
Auto im age
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
pan left, right, up or
down.
7. Press MENU to exit.
The auto image function automatically sizes and positions the
image to fit optimally in the screen picture. In addition it takes
care for phase adjustment. It does not affect the selected
picture format. When Auto image is set to ON, the Horizontal
size, Shift and Phase options are greyed out.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Move pointer to select the area to be enlarged.ꢀ
Press OK key when done.
Horizontal size
The Horizontal size function is used to size a computer image to
make it fit the projected picture. The horizontal size parameter
has permanent scope. When the OSD menu is active and the
horizontal size option is selected, the level will be indicated
graphically on a linear scale (gauge). The default output level
conforms to the value set by the Auto image function. Switching
to another data mode automatically restores Auto image if the
data mode is not part of the ten most recently used display
modes.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Operation
Display and picture control/ Audio control
Audio Control
Mirror
The projector’s sound is set to standard specifications at the
The projector can be used in various positions with respect to
the viewers and the projection screen. With the Mirror function
the picture can be displayed in a way that is suitable for a
specific application.
factory. However, you can adjust the sound to suit your own
preferences by using the Audio control feature.
The following adjustments can be made:
–
–
–
–
Volum e – adjusts the sound level;
Bass – adjusts the bass tones;
Treble – adjusts the high tones;
Mute – mutes the sound of the projector (or an externally
connected loudspeaker).
Rear screen projection
The image can be flipped to a horizontal mirror image of the
input signal for rear screen projection.
1. Select the required input (Data, Video or S-Video).
2. Press Menu.
SCREEN
–
The menu bar appears on the screen.
3. Use Cursor Control to select AUDIO in the menu bar.
4. Use Cursor Control to select the item to be adjusted.
5. Use Cursor Control to make the required adjustment in the
action window.
6. If required, select the next item to be adjusted or press
Menu to exit.
Front projection
Notes:
– The volume can also be adjusted with the – Volume + buttons or
on the remote control.
SCREEN
– When the projector is connected to an amplifier or stereo
system, the volume must be adjusted on the amplifier or
stereo system.
Caution!
Always reduce/check the volume setting of connected amplifiers
before switching off (A/V) mute, to prevent damage to speakers.
Rear projection
Ceiling-m ount projection
The projector is equipped with an upside-down scan function
(vertical mirror), which allows the image to be flipped when the
projector is mounted upside down to the ceiling.
SCREEN
Ceiling projection
1. Press Menu.
–
The menu bar appears on the screen.
2. Use Cursor Control to select Picture in the menu bar.
3. Use Cursor Control to select Mirror from the sub menu.
4. Use Cursor Control to select the correct setting for your
application.
5. If required, select another item you wish to adjust or press
Menu to exit.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Operation
Other settings
Other Settings
The projector is equipped with the following functions to
optimize its use and handling:
Start-up screen
This function allows you to display or suppress the default
Philips start-up screen upon the projector’s start up.
1. Press Menu.
–
The menu bar appears on the screen.
2. Use Cursor Control to move the cursor to Settings.
3. Select Start-up screen by using Cursor Control.
4. Select On to use the default setting or Off to suppress the
start-up screen.
5. Press Menu to close the On Screen Display.
Feedback
This function allows you to suppress OSD messages. Warning or
error messages however are never suppressed.
1. Press Menu.
–
The menu bar appears on the screen.
2. Use Cursor Control to move the cursor to Settings.
3. Select Feedback by using Cursor Control.
4. Select On to have OSD screens displayed or Off to suppress
the display of OSD screens.
5. Press Menu to close the On Screen Display.
Key lock
Key lock is used to de-activate all remote and local controls. You
have to switch the projector off and on again by pulling out the
mains cable to unlock the keys.
1. Press Menu.
–
The menu bar appears on the screen.
2. Use Cursor Control to move the cursor to Settings.
3. Select Key lock by using Cursor Control.
4. Press OK (–/ – –) for 3 seconds to lock all keys.
5. The On Screen Display will disappear automatically.
Factory reset
This function is used to reset all user settings to the default
factory settings.
1. Press Menu.
–
The menu bar appears on the screen.
2. Use Cursor Control to move the cursor to Settings.
3. Select Factory reset by using Cursor Control.
4. Press OK (–/ – –) for 3 seconds to reset all user settings.
5. Select the next item to be adjusted in the sub menu or press
MENU to close the On Screen Display.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Maintenance
Cleaning
Caution!
8. Replace the filter.
Firmly press the filter edges
in place.
Switch off and disconnect the projector before cleaning.
1. When the cabinet is dusty, clean it by gently wiping with a
soft cloth.
2. A chamois leather slightly moistened with water is sufficient
for cleaning the housing.
Check if the filter is firmly
tightened by turning the
cover upside down.
3. Do not use cleaning agents as they may harm the housing.
Alw ays keep the lens clean
1. When the lens is dirty or dusty, first blow the dust off and
then gently wipe with a soft brush or lens cleaning paper.
Never touch the lens with your fingers.
2. The lens is likely to become mouldy if left dirty.
Cleaning the dust filter
1. Press the Stand by On button to switch off the projector.
9. Replace the cover.
–
The standby indicator lights up red.
2. Wait until the cooling fan has stopped (about 3 minutes and
disconnect the mains lead and all other cables.
3. Turn the projector over. Never place the projector on the side
where the connections are located!
F
T
L I
L I
E T
R E
R
4. Press tab A and lift up the cover.
A
F
T
L I
L I
E T
R
Notes:
– We advise you to clean the filter every 100 hours.
– Operating the projector without filter or with a torn or damaged
filter may seriously damage the projector.
– When the filter is damaged replace it with a filter of the same type
(12 nc: 3122 434 01180).
– The projector power cannot be switched on again unless the filter
holder is installed correctly.
5. Turn the cover upside down. The filter is located on the cover
underside.
6. Carefully remove the filter
from the cover.
Maintenance of the trackball rem ote control
Your trackball on the remote control is very durable and will provide
years of use. It has a self-cleaning ball-cage that helps prevent dust
and lint built-up around the ball. If the screen cursor jumps or moves
abnormally, we recommend that you clean the trackball manually.
To clean your trackball
1. Turn the retainer ring counter-clockwise to remove the ball.
2. Wipe the ball with a clean, lint-free cloth.
3. Blow carefully into the ball cage to dislodge dust and lint.
4. Look for a built-up of dirt on the rubber rollers inside the ball
cage. This build-up usually appears as a stripe running around the
middle of the roller.
5. If dirty, clean the rollers using a cotton swab moistened lightly
with isopropyl (rubbing) alcohol. After cleaning, make sure the
rollers are still centered in their channels.
6. Make sure that fluff from the swab is not left on the rollers.
7. Replace the ball and retainer ring.
7. While firmly holding the filter, gently remove any
accumulated dust with a vacuum cleaner.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Maintenance
Lam p
Lam p Replacem ent
When operation time
1. Press the Stand by On button to switch off the projector.
reaches the last 100 hours
of the average lamplife, the
message ‘Warning: lamplife
has almost expired’ will be
displayed on the screen,
each time the projector is
switched on.
–
The standby indicator lights up red.
Multimedia projectorsꢀ
ꢀ
Warning:ꢀ
Lamplife has almost expiredꢀ
ꢀ
It is suggested to have a spare lamp available.ꢀ
The lamp type is indicated in the user guide.
2. Wait 5 minutes for the lamp to cool down and the cooling fan
to stop and disconnect the mains lead and all other cables.
3. Turn the projector over. Never place the projector on the side
where the connections are located!
4. Unscrew the screws at the bottom of the cover and remove
the cover.
The lamplife remaining can
be checked using the OSD
menu.
Displayꢀ
ꢀ
Languageꢀ
Keystone correctionꢀ
Start-up screenꢀ
Feedbackꢀ
Picture
Audio
Settings
F
T
L I
L I
E T
R E
R
1. Press the Menu.
–
The menu bar appears
on the screen.
2. Use Cursor Control to
move the cursor to
Settings.
3. Use Cursor Control to
select Lamp counter.
Lamp counterꢀ
Key lock...ꢀ
Factory reset...ꢀ
ꢀ
ꢀ
Lamp counterꢀ
5 hoursꢀ
ꢀ
–
The remaining lamplife
hours are displayed in
the action window at the
bottom of the screen.
5. Read the caution and warning labels on the lamp cover.
6. Unscrew the lamp holder.
Lamp counter shows the operating hours of the ꢀ
lamp. It is suggested to reset when a new lamp is ꢀ
inserted. To reset keep confirmation key pressed ꢀ
for 3 seconds.
–
When the lamplife has
expired,the lampindicator
lights up orange and the
message ‘Warning:
Multimedia projectorsꢀ
ꢀ
Warning:ꢀ
Lamplife has expiredꢀ
ꢀ
It is suggested to change the lamp, ꢀ
to avoid sudden failure and to improve ꢀ
overall picture quality.
lamplife has expired’ is
displayed on the screen.
F
T
L I
L I
E T
R E
R
7. Grasp the lamp holder handle and carefully pull the lamp
holder out of the projector.
F
T
L I
L I
E T
R E
R
21
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Maintenance
Resetting the lam plife tim e
Caution!
For cooling purposes the lamp is open. When removing the
1. Press Menu.
–
–
The menu bar appears on the screen.
lamp do not tilt. If the inner tube is broken glass particles may
fall out.
Be very careful. The lamp and lampholder may still be too hot
to touch.
Keep lamp holder opening to your right. Do not touch lamp or
point lamp holder opening at anyone.
A high-pressure lamp may break if handled improperly.
2. Use cursor control to
select Settings in the
menu bar.
Settings
Displayꢀ
ꢀ
Languageꢀ
Keystone correctionꢀ
Start-up screenꢀ
Feedbackꢀ
Lamp counterꢀ
Key lock...ꢀ
Picture
Audio
–
–
–
ꢀ
Factory reset...
8. Carefully remove the new lamp housing from its package. Do
not touch lamp or point lamp housing opening at anyone. Do
not drop, as the impact may cause the lamp to break.
9. Place the lamp holder in the guiding slots and insert into the
lamp compartment.
3. Use cursor control to
select Lamp counter in
the sub menu.
Displayꢀ
Picture
Audio
Settings
ꢀ
Languageꢀ
Keystone correctionꢀ
Start-up screenꢀ
Feedbackꢀ
Lamp counterꢀ
Key lock...ꢀ
Factory reset...ꢀ
ꢀ
F
T
L I
L I
E T
R
ꢀ
Lamp counterꢀ
0 hoursꢀ
ꢀ
Lamp counter shows the operating hours of the ꢀ
lamp. It is suggested to reset when a new lamp is ꢀ
inserted. To reset keep confirmation key pressed ꢀ
for 3 seconds.
10. Tighten the screws.
4. Press OK (–/ – –) for 3 seconds to reset the lamp counter.
5. If required, select another item you wish to adjust or press
Menu to exit.
11. Replace the cover and tighten the screws.
12. Plug the projector back in by inserting the mains lead in the
Power socket.
13. Press the Stand by On button to switch on the projector.
14. Reset the lamp life time (see ‘Resetting the lamplife time’).
15. Properly dispose of the old lamp.
Note: When replacing the lamp, always use the same type of lamp
LCA3111/00, 12NC 8670 931 11009).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Troubleshooting
Im age is blurred
If a fault occurs, first check the points listed below
before taking the projector for repair. If you are unable to remedy
a problem by following these hints, consult your dealer or
service organisation.
–
•
Image is not focused.
Adjust focus ring.
–
Distance between projector and screen is not correct.
•
Adjust the distance between the projector and the screen.
Warning:
Under no circumstances should you try to repair the projector
yourself as this could invalidate the warranty.
–
•
Signal cable is not correctly connected.
Connect signal cable correctly.
PROBLEM
Im age does not m atch up w ith the projected screen
–
•
POSSIBLE CAUSE
SOLUTION
–
•
Shift and/or Horizontal size are not adjusted correctly.
Adjust Shift or Horizontal size (See ‘Display and Picture
control’, sections ‘Data only’ and ‘Data and Video/S-Video’).
Activate the auto-image function via the On Screen menu.
Im age is not displayed
•
–
•
Mains lead is not correctly connected.
Correctly connect mains lead.
Picture rolls
–
•
Signal cable is not correctly connected.
Connect signal cable correctly.
–
•
The filter holder is not installed correctly or is damaged.
Install the filter holder correctly (see ‘Cleaning the dust filter’
under ‘Maintenance’).
No sound
–
•
Audio cable is not correctly connected.
Connect audio cable correctly.
–
Lamp holder cover is not closed correctly or the lamp holder
is damaged.
•
Close the cover correctly (see ‘Lamp replacement’ under
‘Maintenance’).
–
•
Volume is not adjusted.
Adjust volume.
–
•
Signal cable not correctly connected.
Connect signal cable correctly.
–
•
A/V-mute is active.
Cancel A/V-mute.
–
•
The projector is in Off position.
Press Stand by On to switch on the projector.
Caution!
Always reduce/check the volume setting of connected amplifiers
before switching off A/V mute, to prevent damage to speakers.
Lam p ceased to operate or does not light up at all
(indicator fast flashes red)
The projector does not react to com m ands from the rem ote
control
–
Lamp is still hot while the projector attempts to restart the
lamp.
Do not switch the set off; it will restart the lamp
automatically within a few seconds.
–
•
Distance is too great.
Reduce distance.
•
–
•
Batteries are exhausted.
Replace batteries (see ‘Inserting the batteries in the remote
control’).
–
•
•
Lamp circuit failure or worn-out lamp.
Take the projector to your nearest Service Centre, or
Replace lamp (see ‘Maintenance’).
–
•
IR sensor is obstructed.
Remove obstacle.
Lam p indicator lights up orange
–
Lamp life has expired or almost expired (less than 100 hours
to go).
–
Remote control is not switched on (only trackball remote
controle).
•
See warning messages on the start up screen for details.
•
Switch on the remote control.
Standby LED is red and flashing fast
–
Too high ambient temperature
•
The projector will go into Standby mode. Allow the projector
to cool down; this may take up to 30 minutes. When the LED
stops flashing press any key to activate the projector again.
–
Blocked air inlets/dirty dust filter
•
The projector will go into Standby mode. Clean air inlets or
dust filter and allow the projector to cool down; this may take
up to 30 minutes. When the LED stops flashing press any
key to activate the projector again.
Poor colour
–
Wrong video system has been selected.
•
Select the correct video system (see the selection of the
video system under ‘Operation’).
•
Adjust brightness, contrast, saturation or hue (see ‘Display
and picture control’ under ‘Operation’).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
|