Public Signage
Solutions
EN
User Manual
TYPE NR.
BDL4251V
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
SAFETY INSTRUCTIONS
WARNINGS AND PRECAUTIONS
KNOW THESE SAFETY SYMBOLS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any
inside part of this product.
This symbol alerts you that important literature concerning operation and maintenance has been included
with this product.
Note to CATV system installer: This reminder is provided to call CATV system installer’s attention to Article
820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as
practical.
Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user’s authority to
operate it.
Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.
Attention: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la bome correspondante
de la prise et pousser jusqu’au fond.
Important: One Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement
of U.S. copyright laws. Certain Canadian programs may also be copyrighted and any unauthorized recording in whole
or in part may be in violation of these rights.
TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
The Socket-outlet shall be installed near the apparatus and shall be easily accessible.
Read and follow these instructions when connecting and using your computer monitor:
ꢀ
Unplug the monitor if you are not going to use it for an extensive period of time.
ꢀ
Unplug the monitor if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth
when the power is off. However, never use alcohol, solvents or ammonia-based liquids.
Consult a service technician if the monitor does not operate normally when you have followed the instructions in this
manual.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
The casing cover should be opened only by qualified service personnel.
Keep the monitor out of direct sunlight and away from stoves or any other heat source.
Remove any object that could fall into the vents or prevent proper cooling of the monitor’s electronics.
Do not block the ventilation holes on the cabinet.
Keep the monitor dry. To avoid electric shock, do not expose it to rain or excessive moisture.
If turning off the monitor by detaching power cable or DC power cord, wait for 6 seconds before attach the power
cable or DC power cord for normal operation.
ꢀ
ꢀ
ꢀ
To avoid the risk of shock or permanent damage to the set do not expose the monitor to rain or excessive moisture.
When positioning the monitor, make sure the power plug and outlet are easily accessible.
IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast
remains on the screen for an extended period of time, it may leave an ‘after-image’ or ‘ghost image’ on the front of
the screen. This is a well-known phenomenon that is caused by the shortcomings inherent in the LCD technology. In
most cases the afterimage will disappear gradually over a period of time after the power has been switched off. Be
aware that the after-image symptom cannot be repaired and is not covered under warranty.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
REGULATORY INFORMATION
CE DECLARATION OF CONFORMITY
MMD declare under our responsibility that the product is in conformity with the following standards
• EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment)
• EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment)
• EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment)
• EN6100-3-2: 2006 (Limits for Harmonic Current Emission)
• EN6100-3-3:1995+A1:2001+A2:2005 (Limitation of Voltage Fluctuation and Flicker)
following provisions of directives applicable
• 2006/95/EC (Low Voltage Directive)
• 2004/108/EC (EMC Directive)
• 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on
ISO9000 level.
FEDERAL COMMUNICATIONS COMMISSION (FCC) NOTICE (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
In a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING
EQUIPMENT REGULATIONS.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works
together (computer, monitor, printer, and so on) should have the same power supply source.
The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with
a nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be
located near the equipment and easily accessible.
A protection mark “B” confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-
42107 and PN-89/E-06251.
ELECTRIC, MAGNETIC AND ELECTRONMAGNETIC FIELDS (“EMF”)
1. MMD manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit
and receive electromagnetic signals.
2. One of MMDs’ leading Business Principles is to take all necessary health and safety measures for our products, to comply with all
applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products.
3. MMD is committed to develop, produce and market products that cause no adverse health effects.
4. MMD confirms that if its products are handled properly for their intended use, they are safe to use according to scientific evidence
available today.
5. MMD plays an active role in the development of international EMF and safety standards, enabling MMD to anticipate further developments
in standardization for early integration in its products.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
INFORMATION FOR UK ONLY
WARNING - THIS APPLIANCE MUST BE EARTHED.
Important:
This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this
type of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an
appropriate 3-pin plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a plug
without a fuse is used, the fuse at the distribution board should not be greater
than 5A.
Note: The severed plug must be destroyed to avoid a possible shock hazard should it
be inserted into a 13A socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured in accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN & YELLOW - “EARTH” (“E”)
1. The GREEN AND YELLOW wire must be connected to the terminal in
the plug which is marked with the letter “E” or by the Earth symbol or
coloured GREEN or GREEN AND YELLOW.
2. The BLUE wire must be connected to the terminal which is marked with the letter
“N” or coloured BLACK.
3. The BROWN wire must be connected to the terminal which marked with the letter
“L” or coloured RED.
Before replacing the plug cover, make certain that the cord grip is clamped over the
sheath of the lead - not simply over the three wires.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
中国电子信息产品污染控制标识要求 (中国RoHS法规标示要求)产品中有毒有害物质
或元素的名称及含量
有毒有害物质或元素
部件名称
铅
汞 镉 六价铬 多溴联苯 多溴二苯醚
（Pb）（Hg）（Cd）（Cr 6+）（PBB） （PBDE）
外壳
○
○ ○
○
○
○
○
○
○
○
○
○
○
○
○
× ×
○
○ ○
○ ○
液晶面板
电路板组件
×
×
附件
(遥控器，电源线，连接线)
×
遥控器电池
○ ○
○
○
○
○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006 标准规定的限量要求
以下
◦
×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的
限量要求
◦
环保使用期限
此标识指期限(十年)，电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外
泄或突变，电子信息产品用户使用该电子信息产品不会对环境造成严重污染或对其人身、财产造
成严重损害 的期限。
6
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
NORTH EUROPE (NORDIC COUNTRIES) INFORMATION
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
END-OF-LIFE DISPOSAL
Your new TV/Monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the
amount of reusable materials and to minimize the amount to be disposed of.
Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on
WASTE ELECTRICAL AND ELECTRONIE EQUIPMENT-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EG
governing used electrical and electronic appliances, this product may not be disposed of with normal
household waste. You are responsible for disposal of this equipment through a designated waste electrical
and electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic, contact your local
government office, the waste disposal organization that serves your household or the store at
which you purchased the product.
Attention users in United States:
Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and Federal Laws. For
7
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Contents
The BDL4251V monitor pack* should include:
•
•
•
•
•
•
Main switch cover
Screw for Main Switch cover
BNC TO RCA adapter x 5
Logo guider
•
•
•
•
•
•
LCD monitor
x
2
Power cord (1.8 m)
VGA Signal Cable (1.8 m)
CD User Manual & QSG
Remote Control and AAA Batteries
Clamper
Screw for Clamper
x
2
Cable belt
x
3
(For tightening cables)
Xxxxxxxxxxxxxx
xxxxxxxxxxxxxx
xxxxxxxxxxxxxx
xxxx
BNC TO RCA adapter x 5
Screw for Main switch cover
(M3 6)
x
x
2
Screw for Clamper
(M4 x 8) x 2
Main switch cover
The supplied power cor varies depending on destination.
*
d
Cable belt
(For tightening the power cor
and VGA / HDMI cable)
x
3
For North
America
For EU
For China
d
Power cor
d
Remote Control and AAA
Batteries
*
Please make sure that for all other regions, apply a power cord that conforms
to the AC voltage of the power socket and has been approved by and complies
with the safety regulations of the particular country
.
Clamper
*
You might like to save the package box and packing material for shipping
the monitor
.
*
The following components ar
e
prepared as options.
•
•
External Speakers
Table stand
Logo guider
Video Signal Cable
(D-SUB to D-SUB Cable)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Connection & Button Overviews
Control Panel
POWER button ( ) :To switch the power on/off.
MUTE button : To switch the audio mute ON/OFF.
INPUT button :To set the function while OSD menu is on or to activate input selection menu while OSD menu is off
.
PLUS (+) button :To increase the adjustment while OSD menu is on, or to increase the audio output level while the OSD menu is off.
MINUS (-) button :To decrease the adjustment while OSD menu is on, or to decrease the audio output level while the OSD menu is off.
UP (ꢀ) button : To move the highlight bar up to adjust the selected item while OSD menu is on, or to activate the OSD menu when the OSD
menu is off.
DOWN (ꢁ) button :To move the highlight bar down to adjust the selected item while OSD menu is on, or to activate the OSD menu when
the OSD menu is off.
EXIT button :To return to previous menu while OSD menu is on or to activate the OSD menu when the OSD menu is off.
Main Power Switch : To turn the main power on/off.
Remote control sensor, Power indicator and ambient light sensor : To receive the IR signal from the remote control. The
indicator would show green when the LCD monitor is active and would turn red when the LCD is POWER OFF. While in the case of the system is in
power save mode, it would show both green and red. When SCHEDULE is enabled, it would blink green and glow red. If the indicator blinks red , it
tells that a failure is detected. The image brightness will be auto adjusted when “LIGHT SENSOR” set to “ON” on OSD menu.
NOTE: Keyboard Control Lock Mode This function completely disables the access to all Keyboard Control functions. To enable the
keyboard control lock, press both of “ꢀ” and “ꢁ” buttons and hold down continuously for more than 3 seconds. To recover back to the user mode,
press both of “ꢀ” and “ꢁ” and hold continuously for three 3 seconds.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Terminal Panel
EXTERNAL CONTROL (mini D-Sub 9 pin)
This is for serial connection when multiple BDL4251V monitors are connected. To achieve remote management through RS232C commands (refer to
the RS232C remote control user manual), connect the RS232C OUT connector from a computer or from a different BDL4251V monitor to the
RS232C IN connector from your BDL4251V monitor. The same RS232C commands can be looped through by connecting the RS232C OUT of this
monitor to the next RS232C IN.
VIDEO IN/OUT
VIDEO IN connector (BNC and RCA): To input a composite video signal. Note that BNC and RCA are not available at the same time.
VIDEO OUT connector (BNC): To output the composite video signal fromVIDEO IN connector.
S-VIDEO IN connector (MINI DIN 4 pin): To input the S-video (Y/C separate signal).
COMPONENT IN [Y, Pb, Pr] (BNC)
To connect an equipment such as a DVD player, HDTV device, or Laser disc player.
AC OUT connector
Bypass AC power output from AC IN connector. ( Rating : 100~240Vac, 50-60Hz, 3A Max.)
AC IN connector
To connect with the supplied power cord.
EXTERNAL SPEAKERTERMINAL
To output the audio signal to external speakers from AUDIO IN 1, 2, 3 jack or HDMI.
AUDIO OUT
To output the audio signal from the AUDIO IN 1,2 and 3 jack or HDMI.
AUDIO IN 1, 2, 3
To input audio signal from external equipment such as a computer,VCR or DVD player.
HDMI IN
To input digital video/audio signals from a digital equipment or computer.
DVI-D IN
To input digital video signals from a digital equipment or computer.
VGA IN (mini D-Sub 15 pin)
To input analog RGB signals from a computer or other RGB equipment.
VGA OUT (mini D-Sub 15 pin)
To output the signal fromVGA IN.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Remote Control
SET button
To activate the setting with OSD menu.
AUTO ADJUST button
To
execute the AUTO ADJUST function.
MUTE button
To turn the mute function on/off.
VIDEO SOURCE button
To activate input selection menu, and push “ꢀ” or “ꢁ” to select input
source from [HDMI], [DVI-D], [VGA],[COMPONENT], [S-VIDEO] and
[VIDEO], and then push “SET” to switch to selected input source.
AUDIO SOURCE button
To activate audio selection menu, and push “ꢀ” or “ꢁ” to select audio
source from [AUDIO1] [AUDIO2], [AUDIO3] and [HDMI], and then push
,
“SET” to switch to selected audio source.
SIZE button
To select the pictur
e
size from [FULL], [NORMAL], [CUSTOM] , [DYNAM
IC] and [REAL].
BRIGHTNESS button
To start the BRIGHTNESS OSD selection, and then push "+" or "-"
button to adjust the value.
POWER button
UP button
To turn the power on/off.
If LED Power Indicator on the monitor is not lightening, then the
remote control will not work.
To move the highlight bar up to adjust the selected item when OSD menu
is on.
To move the sub-picture up when in “PIP” mode.
SMART PICTURE button
To select smart picture mode from [HIGHBRIGHT], [STANDARD],
MENU button
o turn the OSD menu on/off.
[sRGB], [CINEMA]
.
T
HIGHBRIGHT: for moving image such as Video
STANDARD: for images (Factory setting)
sRGB: for text based images
PLUS button
increase the adjustment with OSD menu.
T
o
CINEMA: for movies.
To move the sub-picture right when in “PIP” mode.
PIP (Picture In Picture) button
ON/OFF button: To turn PIP mode ON/OFF.
INPUT button: To select the input signal for the sub-picture.
CHANGE button: To exchange between the main picture and sub-
picture.
EXIT button
turn to the previous OSD menu.
T
o
DOWN button
Note:
To move the highlight bar down to adjust the selected item when OSD
menu is on.
The “PIP” and “POP” modes do not work if the screen size is
“CUSTOM” ,“DYNAMIC” or “REAL”.
CONTRAST button
To move the sub-picture down when in “PIP” mode.
To start CONTRACT OSD selection, and then push "+" or "-" button
to adjust the value.
VOLUME UP button
To increase the audio output level.
DISPLAY button
VOLUME DOWN button
To decrease the audio output level.
To turn on/off the setting information displayed on the right-up corner
of the screen.
MINUS button
To decrease the adjustment with OSD menu.
To move the sub-picture left when in “PIP” mode.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Operating Range for the Remote
Control
Handling the remote control
*
*
Do not subject to strong shock.
Do not allow water or other liquid to splash the
If the emote control gets wet, wipe it dry immediately.
void exposur to heat and steam.
remote control.
Point the top of the
sensor during button operation.
Use the emote control within
front of the LCD monitor's emote control sensor and within
remote control towards the LCD monitor's
remote
r
*
*
A
e
r
a
distance of about
7
m/ 23 ft from the
Other than to install the batteries, do not open the
control.
remote
r
a
horizontal and vertical angle 30° with
a
distance of about
3
m/ 10 ft.
NOTE:
T
he
strong illumination strikes the
or when ther is an obstacle in the radiation path.
remote control system may not function when direct sunlight or
remote control sensor of the LCD monitor
,
e
12
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
How to Mount or Attach Feet to the LCD Monitor
You can install the LCD monitor in one of the following two ways:
Method 1: Attach and remove the optional stands
How to install stands
1. Please turn the monitor off.
2. After inserting stand in guide block, fasten the thumbscrews on both sides of the monitor
.
NOTE:
Install the table stand with the longer end of the feet directing to the front.
In the upright position
How to remove the stands
1. Spread the protective sheet on the flat surface
2. Make the monitor lying on the protective sheet.
3. Remove screws using screwdriver and place them in
.
a
a
safe place for
13
reuse.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
To avoid monitor from falling
Take measures to prevent the monitor from falling over in case of an earthquake or other disaster might occur to lessen the probability of injury and
damage.
As shown in the figure below, secure the monitor to a solid wall or pillar using rope (commercially available) strong enough to bear the weight of the
monitor(BDL4251V: approx. 47.5 kg). Screw hooks (commercially available), of ring type rather than C-shaped screw hooks (with opening), are
recommended.
Screw here is not supplied.
Caution:
ꢁ Though the recommended prevention from falling is intended to lessen the probability of injury and damage, it doesn’t assure its effectiveness
against any kind of earthquake or disaster.
ꢁ Before moving the monitor, remove the rope that is securing the monitor.
Method II: Mount the monitor on the wall
Before mounting the monitor to the wall, make sure that the system has been power-off and you have obtain a standard wall-mounting kit
(commercially available). Using mounting interface that comply withTÜV-GS and/or UL1678 standard in North America is recommended.
1. Lay a protective sheet on a table, which was wrapped around the monitor when it was packaged, beneath the surface as not to scratch the screen
face.
2. This device cannot be installed without the correct and complete mounting accessories (not provided in the box). Make sure you have all related
parts available for wall mounting.
3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the
equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation.
4. For the wall-mounting kit, use M6 mounting screws for 400x 400 mm pattern (having a length 10 mm longer than the thickness of the mounting
bracket) and tighten them securely. (Recommended torque: 470 - 635N•cm).
Caution:
For preventing the monitor from falling.
ꢁ Install the monitor with metal brackets for wall or ceiling installation (commercially available) on your own responsibility. For detailed procedures of
installation, refer to the instructions of the metal brackets.
ꢁ To lessen the probability of injury and damage resulting from fall of the monitor in case of earthquake or other disaster, be sure to consult the
bracket manufacturer for installation location.
ꢁ To lessen the risk of falling of the monitor, thread commercially available rope (having a load capacity at least 1960N (200kgf)) through the handles
at the right and left of the monitor and secure the rope to the wall mount brackets or ceiling mount brackets.(Refer to the first paragraph of this
page.)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Ventilation Requirements for enclosure locating
To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Setup Procedur
1. Install the system on the right location
e
3. Connect to external equipment
•
T
o
protect the connected equipment, tur
befor making connections.
Please refer to section “Connectivity” P.18~P.22 for operations.
n
off the main power
CAUTION:
e
THE LCD MONITOR MUST BE MOVED OR INSTALLED BY
TWO OR MORE PERSONS.
•
.
Failur to follow this caution may result in injury and damage when
e
the LCD monitor falls.
4. Connect power cord
•
The power outlet socket should be installed as near to the
equipment as possible, and should be easily accessible.
Fully insert the prongs into the power outlet socket. A loos
connection may cause malfunctioning of the device.
CAUTION:
DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY
•
e
YOURSEL
F.
The LCD display must be installed by
a
qualified technician.
NOTE:
Please efer to “Safety Operation
proper selection of AC power cord
Contact your dealer for mor
e
information.
r
”
section of this manual for
.
CAUTION:
DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE DOWN,
FACE UP OR FACE DOWN.IT’S POSSIBILITY TO CLOCKWISE 90
DEGREES MOUNT. BUT DO NOT COUNTERCLOCKWISE 90
DEGREES MOUNT.
CAUTION:
DO NOT INSTALL THE LCD MONITOR WHERE IT WILL BE
EXPOSED TO DIRECT SUNLIGHT.
Failur to follow this caution will result in display defects.
e
IMPOR
T
ANT
:
Lay the protective sheet, which was wrapped around the LCD monitor
when it was packaged, beneath the LCD monitor so as not to scratch
the panel.
2. Install the remote control batteries
The
install or replace batteries:
1. Press and slide to open the cover
r
emote control is powered by 1.5V AAA batteries.
To
.
2. Align the batteries according to the (+) and (–) indications inside
the case.
3. Replace the cover
.
5. Turn on the power of the
ttached external equipment
a
When connected with
a
computer, turn on the power of the computer
first.
CAUTION:
Incorrect use of batteries can result in leaks or bursting. Be
careful especially about the following points.
6. Operate the attached external equipment
Display the signal from the external equipment by selecting the correct
video and audio sources first.
•
Place “AAA” batteries matching the
+
and signs on each battery
-
to the and signs of the battery compartment.
+
-
•
•
Do not mix battery types.
7. Adjust the sound
Make adjustments to lower or to rise the volume as required.
Do not combine new batteries with used ones. It causes shorter
battery life or leakage of batteries.
•
Remove dead batteries immediately to prevent battery
liquid from leaking into the battery compartment. Don't touch
exposed battery acid, it cause damage to your skin.
8. Adjust the screen
Make adjustments to the display position or settings if
required.
NOTE:
If you do not intend to use the Remote Control for
remove the batteries.
a
long period,
16
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
9. Adjust the image
Make adjustments to brightness or contrast if required.
10. Recommended Adjustment
T
o
r
educe the risk of “image persistence”, please adjust the
following items based on the application being used.
“POWER SAVE” “PANEL SAVING “DATE AND TIME”
,
”
,
.
11. To prevent the main power switch
from being changed
To
prevent the possibility of main power switch being carelessly
pushed, please attach the main switch cover (accessory) onto it
.
NOTE:
With the main power switch cover in place, the main power switch
can not be turned off. Remove main power switch cover in order to
turn of the display.
f
17
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Install the LCD Monitor in
P
ortrait
Mode
BDL4251V can be installed in portrait position, under the following conditions:
Caution:
Portrait mode is effective only when wall-mounted or ceiling-mounted. The feet can not be used for the monitor in portrait position.
Placing the monitor in portrait position, will shorten the average life of the LCD backlight.
Operational Environment (Temperature) shall be limited, as shown below:
Operational
Environment
T
e
mperatur
e
5
-
35 °C
80
/
41 95 °F
-
Humidity
20
-
%
(without condensation)
Please orientate the monitor in the direction shown as the right figure:
Do not place monitor in landscape in any other manner
Clockwise
Counterclockwise
.
How to set-up
1. Remove the feet if they are attached.
2. The
“
”
logo should be on the LEFT side when facing the monitor.
How to Remove the Logo for landscape mode?
1. Remove the logo sticker by forcing a piece of paper under the logo.
2. Using a knife, carefully remove the logo sticker with the paper placing
beneath.
3. Tear off the logo sticker.
How to Use the Logo Guider for Portrait Mode?
1. Before applying, make sure the guider is well shaped. The "PHILIPS"
sticker attached on the end of it could be folded back as figure a.
2.Turn back the logo end of the guider and remove the sticky tape of the
logo.
3. Slide the logo guider along the short side of the front bezel as figure c &
then re-turn the logo end of the guider back to the right side.
4. With your left hand fixing the guider, press the logo by your right hand to
make it stuck firmly on the front bezel.
5. Remove the guider and leave the logo on the front bezel.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Connectivity
Befor making connections:
e
*
First tur
n
off the power of all the attached equipments before make connections.
*
Refer to the user manual included in each separate piece of equipment.
Connectivity Diagram
19
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Connecting to a Personal Computer
As you finish the connection between the computer and the LCD monitor, you could play the contents in the computer
and display them on the LCD monitor
.
Connecting the LCD Monitor to a Personal Computer
•
To achieve this
,
apply the supplied VGA signal cable (mini D-sub 15 pin to mini D-sub 15 pin) to make connection between a PC and the LCD
monitor
(VGA IN connector)
When connecting mor
commercially
available) to make connection between the LCD monitor(VGA OUT connector) and the other (VGA IN connector)
The AUDIO IN 1, 2, 3 or HDMI can be connected for audio input After choosing one of the AUDIO IN connectors, you might need to select
AUDIO 1, 2, 3 or HDMI using the AUDIO SOURCE button on the remote control.
hen connecting mor than one LCD monitors to a PC, apply RCA cable to make connection between the LCD monitor(AUDIO OUT
.
•
e
than one LCD monitors to a PC, apply another VGA signal cable (mini D-sub 15 pin to mini D-sub 15 pin; it’s
.
•
•
.
W
e
connector) and
the other (AUDIO IN 1, 2, 3
)
. HDMI source is not suitable for this case.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Connecting to a Digital Interface Equipment
Connections can be made between the LCD monitor and other digital equipment that is equipped with
a
digital interface compliant with the DVI
(Digital Visual Interface) standard.
Connect the LCD Monitor to
a
Computer with
a
Digital Output
•
•
•
•
The HDMI , DVI-D IN connector accepts
HDMI and DVI-D can receive HDMI video signals from either a HDMI output of for instance a DVD player or from a DVI-D output of a PC.
ensure the display quality use cable with quality prescribed by DVI standards.
The AUDIO IN 1, 2, 3 or HDMI connector can be chosen to receive an audio source
SOURCE button on the remote control. HDMI(for audio) is only selectable only when HDMI or DVI-D (for video) is selected.
Note that the signal of a HDMI / DVI-D connector cannot be output to the VGA OUT connector
a
HDMI cable.
To
,
a
a
.
Select AUDIO 1, 2, 3 or HDMI from the AUDIO
•
.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Connecting to a DVD Player
As you finish the connection between the DVD player and the LCD monitor, you could display the contents from the played DVD on the LCD
monitor. You might like to refer to your DVD player manual for further information.
’
s
Connect the LCD Monitor to
a
DVD Player
•
To achieve this, apply a 3x components cable (Y, Pb, Pr) with BNC connectors at one end and RCA connectors at the other end between DVD
player and display. In case you can only obtain RCA connectors on both ends you can use the in box available BNC-to-RCA converters.
DVD player(Y, Pb, Pr Out) and LCD monitor (COMPONENT). ou might need BNC-to-RCA adapters(including in the accessories) to convert
the BNC connectors to RCA connectors if you are using the separated signaling(Y, Pb, Pr) RCA cable
If your DVD player supports HDMI signaling, apply a HDMI to HDMI cable for the connection
Y
.
•
•
.
The AUDIO IN 2 , 3 (both of RCA connector type) can be used for audio input.
Select [AUDIO 1] ( for 3.5φ phone jack), [AUDIO 2], [AUDIO 3]
Or [HDMI] from the AUDIO SOURCE button on the remote control. HDMI (for audio) is selectable only when HDMI or DVI-D (for video) is
selected.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Connecting to a Stereo Amplifier
You can connect your stereo amplifier to your LCD monitor. Refer to your amplifier's manual for further information.
Connect the LCD Monitor to
a
Stereo Amplifier
•
•
•
•
T
urn on the LCD monitor and the amplifier only after all connections have been finished.
Apply 2 RCA cables (audio left and right) to make connection between the amplifier (audio in) and the LCD monitor
Do not verse the audio left and right jacks.
(audio out).
re
For the preferred audio signal, select [AUIDO1], [AUDIO2], [AUDIO3] or [HDMI] from the AUDIO SOURCE button on the remote control.
HDMI(for audio) is selectable only when HDMI or DVI-D (for video) is selected.
•
The AUDIO OUT RCA connectors output sound from the selected AUDIO SOURCE.
Connecting to a display mounted PC
This monitor has an area in the backcover to mount a small form fact PC or set-top box.
You can connect your mounted PC to your LCD monitor. Use M4 mounting screws for 100x234 mm to fix your mount PC.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Basic Operation
Power ON and OFF Modes
The LCD monitor power indicator will tur
of using the following three options:
n
green while powered on and will turn red while powered off. The monitor can be powered on or
f
1. Pressing the Main Power Switch.
NOTE:
When the Main Power Switch is used to power of
LCD monitor the emote control the power button and the indicator
will not work. Make sur to tur the Main Power Switch on befor
using the other two options.
f
the
,
r
,
e
n
e
2. Pressing the power button.
NOTE:
Befor
e
pressing the power button, be sure to turn on the
Main Power button on the LCD monitor
.
3. Using the
remote control.
NOTE:
Befor
e
operating the remote control, be sure to turn on the Main
Power Switch on the LCD monitor
.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Power Indicator
Status
Power ON
Green
Power Standby
Power OFF
Red
LED Off
Diagnosis
(Detecting failure)
Red Blinking
* See troubleshooting
Using Power Management
Please turn off the LCD monitor when it will not be used for long time. This could potentially increase the life and decrease the power consumption of
the LCD monitor.
Standby mode: Push the power button on the remote control or on the monitor to enter the standby mode.
Power Off: Push the Main Power Switch to enter the power off mode.
Display Signal ofVideo Source Setting to [VIDEO]
Use the input button on the front panel or theVIDEO SOURCE button on the remote control to set video source to [VIDEO].
Use the COLOR SYSTEM OSD menu to select [AUTO], [NTSC], [PAL], [SECAM], [PAL60], [4.43NTSC], according to your video format.
Picture Size
HDMI, DVI-D,VGA
FULL
FULL
NORMAL
NORMAL
CUSTOM
REAL
COMPONENT, VIDEO
DYNAMIC
REAL
CUSTOM
SignalType
4:3
NORMAL SIZE
Recommended Size
NORMAL
DYNAMIC
FULL
Squeeze
NORMAL: Display with the input signal aspect ratio from PC signal, or display in 4:3 aspect ratio at COMPONENT orVIDEO signal.
FULL: Display in the entire screen.
DYNAMIC: Expand 4:3 pictures to the entire screen with non-linearity. (Some round image might be cut by expansion.)
CUSTOM (ZOOM): Images can be expanded beyond the active display area. The image which is outside of the active display area would not be
shown.
REAL: Image will be displayed for one by one pixel.
ZOOM
ZOOM
25
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Smart Picture Mode
HDMI ,VGA
HIGHBRIGTH
HIGHBRIGTH
STANDARD
STANDARD
sRGB
COMPONENT,VIDEO
CINEMA
Audio Source Switching
You can select the audio source using the AUDIO SOURCE button on the remote control.
HDMI
HDMI
AUDIO1
AUDIO2
AUDIO3
Control Lock Mode
This function disables the operation o buttons so that the adjustments you make are not active when they are pressed.
To disable the buttons, press and hold down the ꢀ and ꢁ buttons together for at least 3 seconds.
To enable the buttons, press and hold down the ꢀ and ꢁ buttons together for at least 3 seconds again.
OSD Information
HDMI , VGA
VGA
1024
48kHz 60Hz
AUDIO : 1
V
ideo Source
x
768
Input signal Information
Audio Source
Pictur Size
SIZE FULL
:
e
COMPONENT
COMPONENT
AUDIO : 3
V
i
deo Source
Audio Source
Pictur Size
SIZE FULL
:
e
S-VIDEO, VIDEO
S-VIDEO
NTSC
AUDIO :3
V
ideo Source
Color System of Input Signal
SIZE NORMAL
:
Audio Source
Pictur Size
e
PIP or POP
Main:VGA
Sub:S-VIDEO
VGA
1024
x
768
Main pictur Information
e
48kHz 60Hz
AUDIO : 1
S-VIDEO
Sub pictur
e
Information
Information
NTSC
Main pictur
e
SIZE FULL
:
26
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
OSD (On-Screen-Display) Controls
Press SET button
to enable setting.
Press MENU or
EXIT button to exit.
Press MENU button to
open Main menu. Press
UP or DOWN button to
select sub-menu.
Press UP or DOWN, and PLUS or
MINUS button to select function, or
adjust the setting Press SET button
.
to enable the setting.
Remote Control
Press EXIT button to
open Main menu. Press
UP or DOWN button
to select.
Press INPUT button to
enable the setting.
Press UP or DOWN, and PLUS
or MINUS button to select
Press EXIT button to
exit.
function, or adjust the setting
.
Press INPUT button to enable
the setting.
Control Panel
UP or DOWN button
INPUT button
“+
”
“-”
button
EXIT button
OSD screen
27
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Main-Menu
PICTURE
BRIGHTNESS
Adjusts the overall image and background screen brightness.
Press
Press
+
-
button to increase brightness.
button to decrease brightness.
CONTRAST
Adjusts the image brightness for the input signal.
Press
Press
+
-
button to increase contrast.
button to decrease contrast.
SHARPNESS
This function is digitally capable to keep crisp images at any timing.
It is adjustable to get
a
distinct image or soft one as you prefer and set independently for each
a
pictur mode.
e
Press
Press
+
-
button to increase sharpness.
button to decrease sharpness.
BLACK LEVEL
Adjusts the image brightness for the background.
Press
Press
+
-
button to increase black level.
button to decrease black level.
NOTE: sRGB pictur mode is standard and cannot be changed.
e
NOISE REDUCTION
Adjusts the noise reduction level.
Press
+
button to increase
reduction level.
Press
-
button to decrease
reduction level.
TINT
*
:
INPUT HDMI , (HDMI INPUT MODE-HD), COMPONENT, S-VIDEO, VIDEO only
Adjusts the tint of the screen.
Press
Press
+
-
button the flesh tone color becomes greenish.
button the flesh tone color becomes purplish.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
COLOR
*
:
INPUT HDMI , DVI-D(INPUT MODE-HD), COMPONENT, S-VIDEO, VIDEO only
Adjusts the color of the screen.
Press
Press
+
-
button to increase color depth.
button to decrease color depth.
COLOR TEMPERATURE
Is used to adjust the color temperature.
The image becomes
r
eddish as the color temperatur
e
decreases, and becomes bluish as the color
temperatur increases.
e
COLOR CONTROL
The color levels of red, green, and blue are adjusted by the color bars.
R: Red, G: Green, B: Blue
LIGHT SENSOR
Select “ON” to enable the ambient light sensor.The image brightness will be auto adjusted when
ambient light changed.
SMART CONTRAST
Select “ON” to enable the smart contrast. Can enhancement the image of high contrast ratio.
PICTURE RESET
Selecting Pictur
Select “Yes” and press “SET” button to
Press “EXIT” button to cancel and then retur
e
r
e
set allows you to
r
eset all OSD settings about PICTURE setting.
estor to factory preset data.
to the previous menu.
r
e
n
29
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Main-Menu
SCREEN
H
POSITION
Controls Horizontal Image position within the display area of the LCD.
Press
Press
+
-
button to move screen to right.
button to move screen to left.
V
POSITION
Controls Vertical Image position within the display area of the LCD.
Press
Press
+
-
button to move screen to UP.
button to move screen to DOWN.
CLOCK
*
:
INPUT VGA only
Press
Press
+
-
button to expand the width of the image on the screen the right.
button to narrow the width of the image on the screen the left.
CLOCK PHASE
*
:
INPUT VGA only
Improves focus, clarity and image stability by increasing or decreasing this setting.
ZOOM MODE
Y
ou can select “FULL”, “NORMAL” and “CUSTOM” and “REAL”. (INPUT HDMI,DVI-D,VGA only)
You can also select “FULL”,“NORMAL” “DYNAMIC” and “CUSTOM” and “REAL”. (INPUT
COMPONENT, S-VIDEO, VIDEO only)
Selecting “DYNAMIC” will make the screen display panoramic with the expansion of the middle and
outside of the screen changed. (The upper and the bottom of the image will be cut by expansion.)
Dynamic image is the same as FULL size image when HDTV signal is input.
Selecting “REAL” image will be displayed
1
by
1
pixel.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
CUSTOM ZOOM
“CUSTOM ZOOM” will be selected when you select “CUSTOM” on the screen “ZOOM” mode.
ZOOM: expands the horizontal and the vertical size simultaneously.
HZOOM: expands the horizontal size only.
VZOOM: expands the vertical size only.
H
POSITION: moves to the right with
+
button. moves to the left with
button.
–
button.
V
POSITION: moves up with button. moves down with
+
–
SCREEN RESET
Selecting Screen eset allows you to
Select “Yes” and press “SET” button to
Press “EXIT” button to cancel and then retur
r
r
eset all OSD settings from PICTURE setting.
estor the factory preset data.
to the previous menu.
r
e
n
31
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Main-Menu
AUDIO
BALANCE
Adjusts the balance of L/R volume.
Press
Sound of the left side will be small.
Press button to move the stereo sound image to left.
+
button to move the stereo sound image to right.
-
TREBLE
This feature helps you to accentuate or reduce the high frequency sound.
Press
Press
+
-
button to increase TREBLE sound.
button to decrease TREBLE sound.
BASS
This feature helps you to accentuate or
reduce the low frequency sound.
Press
Press
+
-
button to increase BASS sound.
button to decrease BASS sound.
SPEAKER
This feature helps you to cut the internal or the external loudspeaker.
Press + or - button to exchanges the internal and the external loudspeaker.
AUDIO RESET
Selecting Audio
Select “YES” and press “SET” button to
Press “EXIT” button to cancel and then retur
r
eset allows you to
r
eset all OSD settings from AUDIO setting.
estor the factory preset.
to the previous menu.
r
e
n
32
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Main-Menu
PIP (PICTURE IN PICTURE)
Note: The “PIP” and “POP” modes do not function when the screen size is “CUSTOM” or “REAL”.
PIP SIZE
Selecting the size of pictur inserted at the “Picture-in-Picture” (PIP) mode.
e
“Large”, “Middle” and “Small” ar available.
e
PIP AUDIO
Selecting the sound source in PIP mode.
When selecting “MAIN AUDIO”, you will get the sound for the main pictur and when selecting
e
“PIP AUDIO”, you will get the sound for the pictur instead.
e
PIP RESET
Selecting PIP Reset allows you to
Select “Yes” and press “SET” button to
Press “EXIT” button to cancel and then retur
r
eset all OSD settings from PIP setting.
estor the factory preset data.
to the previous menu.
r
e
n
33
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Main-Menu
CONFIGURATION
1
AUTO ADJUST
*
:
INPUT VGA only
Press "SET" button to automatically adjust screen size, horizontal position, vertical position, clock,
clock phase, white level and black level.
Press
"
EXIT
"
button to cancel execution AUTO ADJUST and then will return to the previous menu.
POWER SAVE
Selecting RGB "ON", the monitor will go to power management mode when HDMI, DVI-D,VGA, sync is
lost.
Selecting VIDEO "ON", the monitor will go to power management mode after about 10 minutes delay
from when COMPONENT and VIDEO input signal is lost.
LANGUAGE
OSD control menus ar available in eight languages.
e
(English, German, French, Italian, Spanish, Polish, Turkish, Russian, Simple Chinese
)
PANEL SAVING
Select "PANEL SAVING" functions to reduce the risk of the "image persistence".
COOLING FAN:The cooling fan will be auto-turned on and off according to temperature of monitor
when selected “AUTO”.The cooling fan will be turned on always when selected “ON”.
BRIGHTNESS: The brightness is decreased when selected "ON".
PIXEL SHIFT: Image is slightly expanded and moves 4 directions (U
(Need setting the time for movement).
P,
DOWN, RIGHT LEFT) periodically
,
Movement area is approximately +/- 10mm from original position;
Please locate the important information such as text within 90% area of screen image.
See note (1) for this functions.
PIP and STILL will be disabled when "MOTION" is active.
COLOR SYSTEM
*
:
INPUT S-VIDEO, AV only
Selecting the Color System depends on your input video format.
AUTO: NTSC, AL, SECAM, AL60 or 4.43 NTSC is automatically selected.
NTSC: Specific selection of NTSC.
AL: Specific selection of AL.
SECAM: Specific selection of SECAM.
AL-60: Specific selection of AL60.
4.43NTSC: Specific selection of 4.43 NTSC.
P
P
P
P
P
P
34
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
CONFIGURATION RESET
Selecting the CONFIGURATION RESET allows you to reset all configuration settings.
Select "Yes" and press "SET" button to
r
estor
e
the factory preset data.
Press
"
EXIT
"
button to cancel and
r
etur the previous menu.
n
F
ACTOR
Y
RESET
Selecting "YES" allows you to reset PICTURE, SCREEN, AUDIO, CONFIGURATION1,2 and
ADVANCED OPTION will be back to factory settings (except LANGUAGE, DATE AND TIME and
SCHEDULE).
Select "YES" and press "SET" button to
cancel and etur the previous menu.
r
estor
e
the factory preset data. Press
"
EXIT button to
"
r
n
35
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Main-Menu
CONFIGURATION
2
OSD TURN OFF
The OSD control menu will stay on as long as it is used. In the OSD
T
urn Of
f
submenu, you can select
how long the monitor waits after the last touch of button to shut of
a
f the OSD control menu.
The preset choices ar -120 seconds.
e
5
INFORMATION OSD
Selects the information OSD to be displayed or not.
The information OSD will be displayed when the input signal is changed or a source change or warning
message like no-signal or out-of range.
A
time between
1
to 10 seconds is available.
SLEEP TIMER
select SLEEP TIMER mode ON/OFF.
T
o
In the SLEEP TIMER menu, you can preset the monitor to automatically power down.
time between to 24 hours is available.
When the SLEEP TIMER is set, the SCHEDULE settings will be disabled.
A
1
OSD
H
POSITION
Adjusts the horizontal position of the OSD menu.
OSD
V
POSITION
Adjusts the vertical position of the OSD menu.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
MONITOR INFORMATION
Indicates the model and serial number of your monitor
.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Main-Menu
ADVANCED OPTION
INPUT RESOLUTION
*
:
INPUT VGA only
This feature makes the display controlling the source in order to match display capabilities by choice or
automatically. You can select one of the following timings:
(1)1024x768, 1280x768, 1360x768 and 1366x768.
(2) 640x480, 720x480 and 852x480
(3) 800x600, 1064x600 and 720x576
(4) 1400x1050 and 1864x1050
(5) 720x400 and 640x400
AUTO: Determines the
resolution automatically.
The setting you select becomes effective when POWER is turned OFF and ON again.
BLACK LEVEL EXPANSION
*
:
INPUT HDMI, DVI-D(MODE-HD), S-VIDEO, VIDEO only
Selects level of black expansion from “OFF”,”LOW”, “MIDDLE” and “HIGH”.
a
In case of go under the black cut-off level, please adjust the “Black level” in moderation on OSD menu.
GAMMA SELECTION
Selects
2.2
a
display gamma. It refers to the brightness performance curve of signal input.
2.4
S
gamma
Native
NOTE: sRGB pictur mode is standard and cannot be changed.
e
SCAN MODE
*
:
INPUT HDMI, DVI-D(MODE-HD), S-VIDEO, VIDEO only
Changes the display area of the image.
OVERSCAN: Set to display area about 95%
UNDERSCAN: Set to display area about 100%
SCAN CONVERSION
*
:
INPUT HDMI, DVI-D(MODE-HD), S-VIDEO, VIDEO only
Selects IP (Interlace to Progressive) converter function.
PROGRESSIVE: Enable the IP function, to convert interlace signal to progressive. Normally use
this setting.
INTERLACE*: Disable the IP function.
*NOTE: This mode is better suited for motion pictures, but it increases chance of image retention.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
FILM MODE
*
:
INPUT HDMI, DVI-D(MODE-HD), S-VIDEO, VIDEO only
Selects Film mode function.
AUTO: Enable the Film mode function. This mode is better suited for movies, which is converted 24
Frames/sec source to DVD ideo. ecommend to select “PROGRESSIVE” in “SCAN CONVERSION”.
V
We
r
OFF: Disable the Film mode function. This mode is better suited for Broadcasting or VCR source.
IR CONTROL
Selects the operation mode of the
RS232C.
remote controller when multiple BDL4251V monitors are connected via
The item in this menu will become effective by pressing “SET” button on the selected item.
NORMAL: The monitor will be controlled normally by emote controller
PRIMARY The first BDL4251V monitor of those multi-connected via RS232C is designated as PRIMARY
SECONDARY BDL4251V monitors other than the first one multi-connected via RS232C ar designated
as SECONDARY
LOCK: Disable the monitor control by infrared
r
.
:
.
:
e
.
r
emote controller
.
Keep pressing “DISPLAY” button during
5
sec or more, this setting will
return to “NORMAL”.
KEYBOARD CONTROL
Selects the operation mode of the keyboard control
.
Select “LOCK” to disable the keyboard.
Select “UNLOCK” to enable the keyboard.
TILING
TILING demonstrates multiple screens. This feature provides
It will be able to divide up to each and V.
This requires you to feed the PC output into each of the monitors through
MONITORS: Select number of horizontal monitors.
MONITORS: Select number of vertical monitors.
POSITION: Select position to expand the screen.
a
single large screen using up to 25 monitors.
5
H
a
distributor.
H
V
a
FRAME COMP: Works in tandem with TILING to compensate for the width of the tile bezels in order
to accurately display the image.
ENABLE: Select “YES”, the monitor will expand the selected position.
PIP and STILL will be disabled when “TILING” is activated.
HEAT STATUS
*
:
Disclamer: Heat sensor is indicative.
HEAT STATUS allows you to watch the thermal status at any time via the OSD menu and/or via RS232C
commands.The indicated temperature has a accuracy of 3 degrees (plus and minus)..
Press “SET” button to enter the submenu to monitor the heat status
.
Press “EXIT” button to cancel and then return the previous menu.
DATE AND TIME
Adjusts the current date and time for internal clock.
You should set this function when you use “SCHEDULE”.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
SCHEDULE
Programs the monitor's working schedule.
Schedules the power on and power off by using hour and day of the week. Also sets the input port.
a
This OSD can't be removed except EXIT
.
MONITOR ID
ID numbers for remote control are assigned to BDL4251V monitors that are multi-connected via RS232C.
ID numbers 1 to 26 are selectable.
DDC/CI
Use to turn ON or OFF the DDC/CI communication function. Select ON for normal use.
SMART POWER
Selecting SMART POWER allows you to choose a certain level of power saving condition.
Select “OFF” to set the system in normal power condition
Select “MEDIUM” to set the system in medium level power saving status.
Select “HIGH” to set the system in high level power saving status
Press “EXIT” button to cancel and then return the previous menu.
ADVANCED OPTION RESET
Selecting ADVANCED OPTION RESET allows you to reset all OSD settings from ADVANCED OPTION
settings, except for GAMMA SELECTION, DATE AND TIME, SCHEDULE, HDMI INPUT MODE, DVI-D
INPUT MODE,MONITOR ID, and DDC/CI.
Select “YES” and press “SET” button to restore the factory preset data.
Press “EXIT” button to cancel and then return the previous menu.
GAMMA SELECTION is reset when carrying out the PICTURE RESET in the PICTURE.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
NOTE
NOTE 1: IMAGE PERSISTENCE
Please be awar
“ghost” image of
image persistence is not permanent, but constant images being displayed for
alleviate image persistence, tur of the monitor for as long as the previous image was displayed. For example, if an
e
that LCD
Technology may experience
a
phenomena known as Image Persistence. Image Persistence occurs when residual or
a
previous image remains visible on the screen. Unlike CR
T
monitors, LCD monitors’
long period of time should be avoided.
a
To
n
f
image was on the monitor for one hour and
a
r
esidual image remains, the monitor should be turned of
ecommends displaying moving images and using moving panel saving at
the monitor when not in use.
f
for one hour to erase the image.
As with all personal display devices, PHILIPS
r
a
regular intervals
whenever the screen is idle or turning of
f
Please set “POWER SAVE”, “PANEL SAVING”, “DATE AND TIME” and “SCHEDULE” functions to further
Image persistence.
reduce the risk of
For long life use of Public Display
< Image Sticking of LCD Panel
>
When LCD panel is operated continuously for long hours,
a
trace of electric charge
remains near the electrode inside LCD, and
residual or “ghost”
image of previous image may be observed. (Image Persistence)
Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD ar
e
accumulated along
the displayed image, and it is observed permanently. (Image Sticking)
<
Recommendations
>
For preventing the fast transition to Image Sticking, and for longer life usage of LCD, following ar
e
recommended.
1. Static images should not be displayed for long period. Always use a short cycle to change to other images.
2. In case a fixed image is displayed for a long period, it is advised to activate the pixel shift feature that will periodically move the image in four
directions
3. When not in use, please tur
monitor
4. Reducing the environmental temperatur
When Protection boar (glass, acryl) is installed over the LCD surface, enclosed into the box
temperatur sensors inside monitor
educe the environmental temperature, the monitor should be set Low Brightness or Cooling Fan “ON” by using Screen sever Function.
5. Please use "Panel saving Mode" of monitor
n
off the monitor with your remote control, or use Power Management Function or use the Schedule Function of
.
e
will increase the life of your monitor.
d
/
wall, or stack the monitor, please utilize the
e
.
To
r
.
NOTE 2: HOW TO SETUP SCHEDULE
Using the “SCHEDULE” function allows you to set up to seven different scheduled time intervals when the LCD Monitor will be activated.
You can select the time the monitor turns on and turns off, the day of week the monitor is activated, and which input source the monitor will
use for each scheduled activation period.
effect.
A
check mark in the box next to the number of the schedule indicates that the selected schedule is in
T
o
select which schedule to set, use the up/down arrows to move the number (1 to 7) of the schedule.
Use the (+) and (-) buttons to move the cursor horizontally within the particular schedule. Use the
and select input port. The “SET” button is used to make selection.
If you create schedule but do not want to use power on time, select “--” in the “ON” time slot.
If you do not want to use power of time select “--” in the OFF time slot.
If ther is no input selected (“--” showing in the input spot) the input from the previous schedule will be used.
The selection of EVERY DAY within schedule takes priority over other schedules that ar set up to operate weekly. When schedules
ar overlapping, scheduled Power ON time has priority over scheduled Power OFF time.
If ther ar two schedules programmed for the same time, then the highest numbered schedule has priority
TIMER is set, the “SCHEDULE” function is disabled.
(
)
and
(
)
buttons to increase time
a
a
a
a
f
e
a
e
e
e
e
.
When the “SLEEP
”
41
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
NOTE 3: “PIP”, “POP” and “SIDE BY SIDE”
The following table shows the combination of signal inputs under which the “PIP” and “POP” modes function. These modes do not function,
however, when the screen size is “CUSTOM” or “REAL”.
SUB
HDMI
ꢀ
DVI-D
ꢀ
VGA
ꢀ
COMPONENT S-VIDEO
VIDEO
ꢂ
ꢀ
ꢀ
ꢀ
ꢀ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢀ
ꢀ
HDMI
DVI-D
ꢀ
ꢀ
ꢀ
ꢂ
ꢂ: Supported
ꢀ
ꢀ
ꢀ
VGA
ꢂ
ꢀ: Not supported
ꢀ
ꢀ
ꢀ
COMPONENT
S-VIDEO
VIDEO
ꢂ
ꢀ
ꢂ
ꢂ
ꢂ
ꢀ
ꢂ
ꢂ
ꢂ
Press the “PIP ON/OFF” buttons on the
remote control to change between “PIP”, “POP” and “SIDE BY
SIDE” mode as shown in the diagram below
.
SIDE BY SIDE
ASPECT
SIDE BY SIDE
FULL
PIP
POP
OFF
“PIP”, “POP” mode
resolution (Reference)
PIP SIZE
: 450 dots
: 675 dots
: 900 dots
: 450 dots
X
X
X
X
338 dots
450 dots
675 dots
338 dots
SMALL
MIDDLE
LARGE
POP SIZE
<
Remote control numbering function
>
By connecting multiple BDL4251V monitors using RS232C cables, you can control any one monitor or all the monitors by one
remote controller.
1. Assign arbitrary ID number to each of multi-connected BDL4251V monitors using MONITOR ID. ID numbers 1
to 26 ar
It is recommended to assign sequential ID numbers from
2. The emote control mode of the first BDL4251V monitor is set to PRIMARY and those of the other monitors ar
SECONDARY
3. When you direct the
button on the emote controller
e
selectable.
1
and up.
r
e
set to
.
r
emote controller at the
remote control signal sensor of the PRIMARY monitor and press the DISPLAY
r
,
the ID selection OSD appears at the upper left of the screen.
ID number of the currently viewed monitor
Select the ID number of the monitor you want to control using the +/- button
on the remote controller.
The ID of the monitor you want to control is displayed at the upper left of its screen.
By selecting ALL, you can control all the multi-connected monitors.
4. Direct the
remote controller at the remote control signal sensor of the PRIMARY monitor. OSD appears
on the monitor having the ID number you selected.
NOTE:
When the ID selection OSD is being displayed on the PRIMARY monitor
ID selection OSD and then control the monitor you selected.
,
press the DISPLAY button on the remote controller again to cancel the
HINT
If you set the
monitor to display the OSD screen and change the
:
r
emote control mode wrongly and
r
emote control operation becomes unavailable, press MENU button on the control panel of the
emote control mode using ADVANCED OPTION. By pressing
emote control for seconds or longer, the emote control mode is initialized to
r
and holding down the DISPLAY button on the
NORMAL.
r
5
r
42
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Pixel defect policy BDL4251V
Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and
practice stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays
are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips guarantees
that any Plasma- & LCD- displays with an unacceptable number of defects will be repaired during the warranty period in line with
your local guarantee conditions.
This notice explains the different types of pixel defects and defines the acceptable defect level for the BDL4251V LCD screen. In
order to qualify for repair under warranty, the number of pixel defects must exceed a certain level which is given in the
reference table. If the LCD screen is within specification a warranty exchange / claim back will be refused. Additionally, because
some types or combinations of pixel defects are more noticeable than others, Philips sets even higher quality standards for those.
Pixels and Sub-pixels
A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and blue. Many pixels together
form an image. When all sub-pixels of a pixel are lit, the three colored sub-pixels together appear as a single white pixel. When
all are dark, the three colored sub-pixels together appear as a single black pixel. Other combinations of lit and dark sub-pixels
appear as single pixels of other colors.
Types of Pixel Defects + Dot definition
Pixel and sub-pixel defects appear on the screen in different ways. There are three categories of pixel defects and several
types of sub-pixel defects within each category.
Dot definition = What is a defective “Dot” ?:
One or more defective, adjacent sub-pixel are defined as one “dot”. The no. of defective sub-pixels are not relevant to
define a defective dot. This means that a defective dot can consist of one, two or three defective sub-pixels which can
be dark or lit.
One dot = One Pixel; consists of three sub-pixels of Red; Green and Blue
Bright Dot Defects
Bright dot defects appear as pixels or sub-pixels that are always lit or "on". These are the examples of bright dot defects:
Two adjacent lit sub-pixels:
- Red + Blue = Purple
- Red + Green = Yellow
- Green + Blue = Cyan (Light
Blue)
One lit red, green or blue sub-
pixel
Three adjacent lit sub-pixels
(one white dot)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Dark Dot Defects
Black dot defects appear as pixels or sub-pixels that are always dark or "off". These are the examples of black dot defects:
Two dark dots, specifications
Two adjacent dark dots=
1 pair of dark dots
One dark dot
defines the minimum distance
between dark dots
Proximity of Pixel Defects
Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies
tolerances for the proximity of pixel defects. In the table below you can find specifications about:
•
•
•
Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots)
Minimum distance between dark dots
Total no. of all defective dots
Pixel Defect Tolerances
In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in a Philips Plasma / LCD-
display must have pixel or sub-pixel defects exceeding the tolerances listed in the following table.
BRIGHT DOT EFFECT
MODEL
ACCEPTABLE LEVEL
BDL4251V
1 lit sub pixel
1
BLACK DOT EFFECT
1 dark sub pixel
ACCEPTABLE LEVEL
8
TOTAL DOT DEFECTS OF
ALL TYPES
9
Note:
* 1 or 2 adjacent sub pixel defects = 1 dot defect
44
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Features
Full HD LCD display 1920x1080p
This display has a resolution that is referred to as Full HD.The state-of-the-art LCD screen technology has the full high-definition widescreen
resolution of 1080 progressive lines, each with 1920 pixels.This allows the best possible picture quality for HD input signals with up to 1080
lines. It produces brilliant flicker-free progressive scan pictures with optimum brightness and superb colors.This vibrant and sharp image will
provide you with an enhanced viewing experience.
Slim bezel
A slim bezel design adds a stylish look to a public display to nicely blend in most environments. Furthermore this design is ideal for tiled matrix
video walls.
Zoom function for tiled matrix
The internal zoom function enables easy implementation of a video wall matrix, without the need for expensive external equipment. Capable of
a vidiwall of 25 displays by dividing up to 5 displays each horizontally and vertically.
High brightness
Allows daylight viewing even in large public environments with high ambient light conditions due to its 700 cd/m² high brightness professional
panel.
Network controllability: RS232C
Network controllability allows user to control and adjust monitors remotely through RS232C protocol.
Smart insert
Professional PC's are part of most public signage installations. Quite often they add additional depth to the public display and a lot of cable
clutter. This public display contains a Smart insert in the backcover that will fit many professional small form factor PC's. In addition it offers
provisions for efficient cable management.
SmartPower
The backlight intensity can be controlled and pre-set by the system to reduce the power consumption by up to 50%, which saves substantially
on energy costs.
Advanced anti image sticking
Static images left on-screen for extended periods of time may leave a "ghost image" or image sticking effect on LCD displays.Although image
sticking in LCD displays is not permanent, you want to prevent this to happen, especially in locations where content is shown 24/7.
Compliant with RoHS standards
Philips designs and produces display products in compliance with strict Restriction of Hazardous Substances (RoHS) standards that restrict lead
and other toxic substances that can harm the environment.
Automatic Long Cable Compensation:
Automatic long cable compensation prevents image quality degradation (color shift and dull signals) caused by long cable lengths.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Troubleshooting
No pictur
e
•
•
•
The signal cable should be completely connected to the graphics card/computer
Front Power Switch and computer power switch should be in the ON position.
Check to make sur that supported mode has been selected on the graphics car
(Please consult graphics car or system manual to change graphics mode.)
Check the monitor and your graphics car with espect to compatibility and
.
e
a
d
or system being used.
ecommended settings.
reset the power of the device.
d
•
•
•
d
r
r
Check the signal cable connector for bent or pushed-in pins.
If nothing is displayed on the screen when HDCP device is connected,
Power Button does not respond
•
Unplug the power cor
d
of the monitor from the AC outlet to tur
n
off
and reset the monitor.
Image persistence
•
Please be awar
“ghost” image of
constant images being displayed for
e
that LCD
previous image remains visible on the screen. Unlike CR
long period of time should be avoided.
T
echnology may experience
a
phenomenon known as Image Persistence. Image Persistence occurs when
monitors, LCD monitors’ image persistence is not permanent, but
alleviate image persistence, tur of the monitor for as long as
a
residual or
a
T
a
To
n
f
the previous image was displayed. For example,
if an image was on the monitor for one hour and
a
residual image remains, the monitor should be turned off for one hour to erase the image.
NOTE:
As with all personal display devices, PHILIPS
recommends displaying moving images and using
a
moving panel saving at regular intervals whenever the
screen is idle or turning of the monitor when not in use.
f
Image is unstable, unfocused or swimming is apparent
•
•
Signal cable should be completely attached to the computer
Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment. When the display
mode is changed, the OSD Image Adjust settings may need to be e-adjusted.
Check the monitor and your graphics with espect to compatibility and ecommended signal timings.
If your text is garbled, change the video mode to non-interlace and use 60 Hz efresh rate.
.
r
•
•
r
r
r
Image of component signal is greenish
•
Check to see if the COMPONENT input connector is selected.
LED on monitor is not lit (no green or red color can be seen)
•
Power Switch should be in the ON position and power cor
d
should be connected.
•
Make certain the computer is not in power-saving mode (touch the keyboard
a
or mouse).
RED LED on monitor is blinking
•
A
certain failure might have occurred, please contact your nearest authorized PHILIPS service facility.
Display image is not sized properly
•
•
Use the OSD Image Adjust controls to increase or decrease the coarse adjustment.
Check to make sur that supported mode has been selected on the graphics card or system being used.
(Please consult graphics card or system manual to change graphics mode.)
e
a
Selected resolution is not displayed properly
•
Use OSD Display Mode to enter Information menu and confirm that the appropriate
resolution has been selected.
If not, select corresponding option.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
No Sound
•
•
•
Check to see if speaker cable is properly connected.
Check to see if mute is activated.
Check to see if volume is set at minimum.
Remote Control does not work
•
•
•
Check the Remote Control’
s
batteries status.
Check if batteries ar inserted correctly
e
.
Check if the Remote Control is pointing at the monitor’s remote sensor
.
“SCHEDULE” / “SLEEP TIMER
”
function is not working properly
•
•
The “SCHEDULE” function will be disabled when the “SLEEP TIMER
If the “SLEEP TIMER function is enabled and the power to the LCD monitor is turned of
the “SLEEP TIMER will be reset.
”
is set.
”
f
if the power supply is interrupted unexpectedly, then
”
Stripe Noise
Either light vertical or horizontal stripes may appear, depending on the specifi display pattern. This is no product fault or degradation.
c
“NO SIGNAL” is displayed on the screen
Image may not be displayed right after HDCP device is connected.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Specifications
Specifications (BDL4251V)
Product Specifications
Analog Input
Digital Input
LCD Module
Diagonal:
Pixel itch:
Resolution:
Color:
42"
0.485 mm
1920 1080 dots
1.07 billion colors (depending on video car
700 cd/m2 (typ.)
/
106.7 cm
P
x
d
used)
Brightness:
Contrast Ratio:
Response time:
1,000:1 (typ.) , 3,000:1witch Smart Contrast
9
ms (typ.
Up and Down 178°, Left and Right 178° (typ.) @CR>10
15.625 15.734, 31 91 kHz
50.0 58.0 75.0 Hz
13.5 -165.0 MHz
930.25 x 523.25 mm
G
to G)
View Angle:
Frequency
Horizontal:
ertical:
/
-
V
/
-
Pixel Clock
25.0 -165.0 MHz
TMDS
V
iewable Size
Input Signal
PC-Input:
/
36.6
x
20.6 inches
Analog RGB
Video: 0.7 Vp-p
Video:
Input impedance 75 ohm
Separate HV sync: TTL level (Pos./Neg.),Input Impedance 2.2K ohm
15 Pin Mini D-sub
Sync:
Input-terminal:
HDMI
Composite: 1.0 Vp-p
VIDEO Input:
Input impedance 75ohm BNC and RCA-PINJACK-INPUT
Y/C
Impedance 75 ohm S-TERMINAL-INPUT
Component: 1.0 0.7 Vp-p
Input Impedance 75 ohm BNC-INPUT
RCA PIN-JACK L/R INPUT 2, STEREO Mini Jack INPUT
Pin Mini D-sub
Y: 1 Vp-p C: 0.286 Vp-p Input
/
AUDIO Input:
RS232C:
x
x
1
In:
9
Output Signal
Analog RGB
Separate HV sync: TTL level (Pos./Neg.)
15 Pin Mini D-sub
Video: 0.7 Vp-p with 75 ohm terminated
PC-Output:
Video:
Sync:
Output-terminal:
BNC-OUTPUT
RCA PIN-JACK L/R OUTPUT
Internal Speaker
External Speaker Jack
x
1, Composite 1.0 Vp-p with 75 ohm terminated
1, 0.15 rms with 47k ohm terminated
(8 ohm)
(8 ohm)
VIDEO Output:
AUDIO Output:
Speaker Output:
x
W
V
5
7
W
W
+
+
5
7
W
9
Pin Mini D-sub
RS232C:
Out:
Resolutions Supported
640
800
x
x
480 at 60 Hz
600 at 60Hz
1024
x
768 at 60Hz
1280 x 720 at 60Hz
1280
1360
1600
x
x
x
768 at 60Hz
768 at 60Hz
1200 at 60 Hz
1900x1200 (reduced Blanking only)
1920 1080 at 60Hz*
Recommended Resolution
NTSC,PAL,SECAM,4.43NTSC,PAL60 DVD:480i,480p, 576i,720p,1080i,1080p
2.4 1.2 @100 240 AC, 50 60 Hz
Typically 232
Less than 1W (Power button off or main power switch off.)
40 °C 41-104 Portrait : 5 35 °C 41
(Without condensation)
60 °C -4 140 °F
90% (Without condensation)/90%-3.5%x(T
Net without stand: 967.6 mm (W) 559.6 mm (H) 123.1mm (D)
Net with stand: 967.6 mm (W) x605.6 mm (H) 405 mm (D)
Gross:
Net without stand: 48.5lbs
x
*
Power Supply
Power Consumption
–
A
-
V
~
W
Power Save:
T
Operational
Environment
Storage
Environment
Dimension
emperature: Landscape:
Humidity: 20
80
emperature: -20
Humidity: 10
5
-
/
°
F
,
-
/
-
95 °F
-
-
-
%
T
/
-
e
mp-40°C) regarding over 40°C
38.09" (W) x 22.03" (H) x 4.85" (D)
38.09" (W) 23.84" (H) 15.95" (D)
70.87 28.15 11.26
x
x
x
/
/
x
x
1170
mm (W)
x
715 mm (H)
x
286 mm (D)
/
"
(W)
x
"
(H)
x
"
(D)
Weight
/
22 kg
23.8 kg
31.2
Net with stand:
Gross:
52.47 lbs
/
/
68.78
lbs
Holes (400 mm pitches)
Optional Multi-purpose Fix Mount
kg
8
Wall mounting interface
Complied Regulatory and Guidelines
Power Management
UL60950-1/C-UL/EN60950-1/FCC-B/EN55022-B/EN55024/EN61000-3-2/EN61000-3-3 /CE
SupportVESA DPMS convention
Plug
Accessories
Note: echnical specifications ar subject to change without notice.
&
Play
VESA DDC2B, DDC/CI
CD User's Manual, QSG, Power Cord, VGA Cable, BNC TO RCA adapter x 5, Remote
Controller
,
AAA Battery
x
2, Clamper
x
2
(T
x
o
prevent from falling), Cable belt x 3 (For
securing cables), Screw for Main switch cover
2, Main switch cover.
2, Screw for CLAMPER 2, Cable Holder x
x
T
e
48
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Pin Assignment
1) Analog Video Signal Input (Mini D-SUB 15P): VGA
Pin No
Name
1
2
Video Signal Red
Video Signal Green
Video Signal Blue
3
Mini D-SUB 15P
1
6
4
GND
5
5
DDC-GND
Red-GND
Green-GND
Blue-GND
+5V (DDC)
SYNC-GND
GND
10
15
6
11
7
8
9
10
11
12
13
14
15
DDC-SDA
H-SYNC
V-SYNC
DDC-SCL
2) S-VIDEO input (MINI DIN 4P): S-VIDEO
MINI DIN 4P
Pin No
Name
1
2
3
4
GND
GND
Y (Luminance)
C
(Chroma)
3) HDMI
:
Pin Assignment of HDMI connector:
-
1
2
3
4
5
6
7
8
TMDS Data0 Shield
TMDS Data0-
15
TMDS Data2+
TMDS Data2 Shield
TMDS Data2-
SCL
SDA
1
HDMI
19
18
9
16
17
18
19
10 TMDS Clock+
11
12 TMDS Clock-
13
14 Reserved (N.C. on device)
DDC/CEC Ground
+5V Power
TMDS Data1+
TMDS Data1 Shield
TMDS Data1-
TMDS Clock Shield
Hot Plug Detect
CEC
2
TMDS Data0+
4) RS232C input/output
Pin No
Name
Mini D-SUB 9P
1
2
3
4
5
6
7
8
9
NC
5
RXD
TXD
NC
1
6
9
GND
NC
RT
S
CTS
NC
49
Download from Www.Somanuals.com. All Manuals Search And Download.
User Manual BDL4251V
Specifications ar
e
subject to change without notice.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Peavey Speaker 115P User Manual
Pelco Home Security System CC3751H 2 User Manual
Philips Electric Shaver 6829 User Manual
Philips TV VCR Combo 21PV708 User Manual
Philips TV VCR Combo CCB193AT99 User Manual
Playskool Games 50502 User Manual
Polycom Flat Panel Television 42PF5331 User Manual
Poulan Lawn Mower 191798 User Manual
Power Acoustik Speaker REP 12 User Manual
ProForm Computer Monitor 240P2 User Manual