Philips Network Card 0910L2S User Manual

l a u n a M n o i t a l l a t s n I  
Contact Information:  
Other World Computing 1004 Courtaulds Drive Woodstock, IL 60098  
Sales: 800.275.4576  
International: 815.338.8658  
Customer Service: 800-275-4576  
Tech Support: 815-338-8685  
24hr Fax: 815.338.4332  
For support via email submit your question here:  
Sales & Technical Support Hours (CST)  
8:30AM-8PM Monday - Friday  
10AM-4PM - Saturday  
Customer Service Hours (CST)  
8:30am-5:30pm Monday - Friday  
Entire contents copyright ® 2004 Other World Computing.  
OWC product warranties are non-transferOrabWle CMANMEG4  
Troubleshooting Tips:  
4 G e m e r t x E y r u c r e M C W O  
FCC Statement  
Boot Issues:  
NOTE: Other World Computing declares that this processor upgrade  
has been tested and found to comply with the limitations of a Class B  
digital device, pursuant to Part 15 of the FCC Rules & Regulations. These  
limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates,  
uses and can radiate radio frequency energy and, if not installed in  
accordance with these instructions, may cause harmful interference to  
radio communications. However, there is no guarantee that interference  
will not occur in any one particular installation, If this equipment does  
cause harmful interference to radio or television reception, this can be  
determined by turning the equipment this upgrade is installed into on and  
off. If this is determined to be the cause of harmful interference, the end  
user is encouraged to attempt to correct the interference by one or more  
of the following procedures:  
Make certain you updated the firmware to version 4.2.8. If you did not,  
you will have to reinstall your original processor and boot into Mac OS 9  
to perform this task.  
• Press the reset button marked “S1” on the logic board. This is located  
on the corner of the logic board near the PCI slots on most machines.  
You will need to reset your date & time settings as well as any AppleTalk  
settings after doing this.  
• Reset the PRAM on your computer by pressing and holding the  
command - option - P and R keys at startup until the machine chimes  
3 times. You will need to reset your date & time settings as well as any  
AppleTalk settings after doing this.  
Final Cut Pro 3 and 4 Issues / Full Switch Setting Chart:  
Final Cut Pro requires a valid speed to be reported correctly by Apple  
System Profiler. For detailed instructions about this issue, please visit our  
This page also includes a full switch setting chart for your convenience.  
• Connect the equipment to another electrical outlet, or use a line filtering  
device between the outlet and the computer  
• Move the location of the receiving device and the computer  
• Reorient the receiving antenna  
Sleep Issues:  
• Increase the distance separating the receiver and the computer  
• The OWC Mercury Extreme G4 supports hard disk and display sleep in  
all configurations. With some system configurations, deep sleep may not  
be supported.  
9. Remove Processor  
11. Insert Processor - All Systems  
Installation of the processor daughtercard is the same on all  
systems, simply align the 3 screw holes in the card and gen-  
tly place over the logic board. Gently but firmly press straight  
down on the two rearmost screwholes until you feel the card  
“click” into place. Insert the included screwdriver and tighten  
the encapsulated 3 Phillips screws into the 3 screw holes.  
You’re all done - Enjoy your new processor!  
Place your fingers gently underneath the edge of the  
processor daughtercard, and with your fingertips, pull straight  
up. Do not pull at an angle, you risk breaking the processor  
socket if you don’t pull straight up.  
10. Remove Protective Cover  
Optional - Jumper Settings - Adjustment NOT necessary!  
There is no need to modify the settings on the accelerator as  
they are preset for maximum performance from the factory.  
If you wish to adjust, please follow this chart.  
Remove the protective cap from the OWC Mercury Extreme  
G4 processor upgrade. The cap is located on the bottom of  
the card, between the screw holes. Place the cap onto the  
processor card you just removed.  
NOTE: See Troubleshooting section for Final Cut Pro issues.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco Home Security System C1987M User Manual
Pelican Work Light 2010 User Manual
Pentair Universal Remote QT4 User Manual
Philips Computer Monitor 107T51 User Manual
Philips Headphones SBCHC210 31 User Manual
Philips TV VCR Combo 21PV335 User Manual
Poulan Lawn Mower Accessory 406288 User Manual
Presonus Audio electronic Music Mixer FireStudio LightPipe User Manual
ProForm Treadmill PFTL69711 User Manual
Proxima ASA Projector dp800 User Manual