Always there to help you
Register your product and get support at
AEA7100
Question?
Contact
Philips
User manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1 Important
2
Safety
Notice
2
3
2 YourWireless Microphone and
Bluetooth® Speaker
Introduction
5
5
5
5
What’s in the box
Overview of the unit
3 Get started
7
7
7
7
Connect power
Switch on the Bluetooth® speaker
Install/replace microphone batteries
4 Play
9
9
Sing along through the wireless
microphone
Play from a Bluetooth® enabled device 10
Play and charge your iPad through the
dock connector directly
Play from an external device
11
12
5 Product information
13
13
Specifications
6 Troubleshooting
14
EN
1
Download from Www.Somanuals.com. All Manuals Search And Download.
i Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other.A grounding
type plug has two blades and a third
grounding prong.The wide blade or the
third prong are provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
1 Important
Safety
This ‘bolt of lightning’ indicates uninsulated
material within the device may cause an electrical
shock. For the safety of everyone in your
household, please do not remove the covering.
j Protect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
The ‘exclamation mark’ calls attention to
features for which you should read the enclosed
literature closely to prevent operating and
maintenance problems.
WARNING:To reduce the risk of fire or electric
shock, the device should not be exposed to rain
or moisture and objects filled with liquids, such
as vases, should not be placed on the device.
k Only use attachments/accessories
specified by the manufacturer.
l Use only with the cart, stand, tripod,
bracket, or table specified by the
CAUTION:To prevent electric shock, fully
insert the plug. (For regions with polarized
plugs:To prevent electric shock, match wide
blade to wide slot.)
manufacturer or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
Important Safety Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
m Unplug this apparatus during lightning storms
d Follow all instructions.
or when unused for long periods of time.
e Do not use this apparatus near water.
f Clean only with dry cloth.
n Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
h Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
2
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
o Battery usage CAUTION –To prevent
battery leakage which may result in bodily
injury, property damage, or damage to
the unit:
Notice
Notice of compliance
•
•
•
Install all batteries correctly, + and - as
marked on the unit.
Modifications
Remove batteries when the unit is not
used for a long time.
The user is cautioned that changes or
modifications not expressly approved by the
party responsible for compliance could void the
user’s authority to operate the equipment.
Perchlorate Material-special handling
hazardouswaste/perchlorate.
FCC & RSS compliance statement
p Apparatus shall not be exposed to
dripping or splashing, keep it away from
direct sunlight,naked flames or heat.
This device complies with Part 15 of the FCC
Rules and Industry Canada licence-exempt
RSS standard(s). Operation is subject to the
following two conditions:
Warning
a This device may not cause harmful
• Never remove the casing of this apparatus.
• Never lubricate any part of this apparatus.
• Never place this apparatus on other electrical
equipment.
• Keep this apparatus away from direct sunlight, naked
flames or heat.
interference, and
b This device must accept any interference
received, including interference that may
cause undesired operation.
• Ensure that you always have easy access to the power
cord, plug or adaptor to disconnect this apparatus from
the power.
FCC Radiation Exposure Statement
This equipment complies with FCC’s and IC’s
RF radiation exposure limits set forth for an
uncontrolled environment.The antenna(s)
used for this transmitter must be installed and
operated to provide a separation distance of
at least 20 cm from all persons and must not
be collocated or operating in conjunction with
any other antenna or transmitter. Installers must
ensure that 20cm separation distance will be
maintained between the device (excluding its
handset) and users.
Risk of overheating! Never install this apparatus
in a confined space. Always leave a space of
at least four inches around this apparatus for
ventilation. Ensure curtains or other objects
never cover the ventilation slots on this
apparatus.
Information about the use of batteries:
Caution
• Risk of leakage: Only use the specified type of batteries.
Do not mix new and used batteries. Do not mix
different brands of batteries. Observe correct polarity.
Remove batteries from products that are not in use for
a longer period of time. Store batteries in a dry place.
FCC rules
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation.This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
• Risk of injury:Wear gloves when handling leaking
batteries. Keep batteries out of reach of children and
pets.
• Risk of explosion: Do not short circuit batteries. Do
not expose batteries to excessive heat. Do not throw
batteries into the fire. Do not damage or disassemble
batteries. Do not recharge non-rechargeable batteries.
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation.
additional information on a recycling center in
your area.
Environmental information
If this equipment does cause harmful
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged
to try to correct the interference by one or
more of the following measures:
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
•
•
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
Canada:
“Made for iPad” means that an electronic
accessory has been designed to connect
specifically to iPad, and has been certified by
the developer to meet Apple performance
standards.Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note that
the use of this accessory with iPad may affect
wireless performance.
This Class B digital apparatus complies with
Canadian ICES-003.
Disposal of your old product and
batteries
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
iPad is a trademark of Apple Inc., registered in
the U.S. and other countries.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Philips is
under license.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products and batteries.
The correct disposal of these products helps
prevent potentially negative consequences on
the environment and human health.
Note
Your product contains batteries, which cannot
be disposed of with normal household waste.
• The type plate is located on the back of the unit.
Please inform yourself about the local rules on
separate collection of batteries.The correct
disposal of batteries helps prevent potentially
negative consequences on the environment and
human health.
4
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
2 YourWireless
Microphone
and Bluetooth®
Speaker
What’s in the box
Check and identify the contents of your
package:
•
•
•
•
•
Wireless microphone
Bluetooth® speaker
AC power cord
3 X AAA batteries
Quick start guide
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers, register your product
Overview of the unit
Wireless microphone
If you contact Philips, you will be asked for the
model and serial number of this apparatus.The
model number and serial number are on the
back of the apparatus.Write the numbers here:
b
Model No. __________________________
Serial No. ___________________________
d
Introduction
c
With the wireless microphone and Bluetooth®
speaker, you can:
•
dock your iPad onto the speaker to
sing along with music from the app
(StarMaker Karaoke + Auto-Tune®)
through the wireless microphone.
a
With the Bluetooth® speaker, you can:
a Line out socket
•
play music from a Bluetooth® enabled
device that supports A2DP (Advanced
Audio Distribution Profile).
•
(To use the microphone separately)
connect to the MIC input socket of an
existing Hi-Fi system.
•
•
charge or play music from your iPad
directly through the dock connector.
b Battery compartment
play music from other audio devices
through the AUDIO-IN socket.
c OFF/ON
•
Switch the microphone on or off.
d Power indicator
•
Light up red when the wireless
microphone is switched on.
•
Flash red when the battery level is low.
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Bluetooth® speaker
a
c
d ef
b
i
hg
a Power indicator
•
Indicate the power status.
b
•
Turn the unit on/off.
c Bluetooth® indicator
•
Indicate the Bluetooth® status.
d -/+
•
Adjust volume.
e
•
(Press) pair with a Bluetooth® enabled
device that supports A2DP (Advanced
Audio Distribution Profile).
•
(Press and hold) pair with the wireless
microphone in case automatic pairing
fails.
f Dock for iPad
g SOFTWARE UPGRADE (not for use by
end users)
h AUDIO-IN
•
Connect an external audio player
through a 3.5mm audio input cable
(not supplied).
i AC MAINS~
•
AC power socket.
6
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
To switch the unit to standby mode, press
on the top panel.
3 Get started
To switch the unit on from standby mode,
press again.
Always follow the instructions in this chapter in
sequence.
Tip
• If the speaker stays idle for more than 15 minutes, it
switches to standby mode automatically.
Connect power
Caution
• Risk of product damage! Make sure that the power
supply voltage corresponds to the voltage printed on
the back of the unit.
Install/replace microphone
batteries
• Risk of electric shock! When you unplug the AC power
cord, always pull the plug from the socket. Never pull
the cord.
Caution
• Before you connect the AC power cord, make sure that
you have completed all the other connections.
• Risk of explosion! Keep batteries away from heat,
sunshine, or fire. Never discard batteries in fire.
• Danger of explosion if batteries are incorrectly
replaced. Replace only with the same or equivalent
type.
• Batteries contain chemical substances, so they should
be disposed of properly.
1
Open the battery compartment and take
out the battery cartridge.
•
Connect the AC power cord to
•
the AC MAINS~ socket on the back
of the Bluetooth® speaker.
•
the wall power socket.
Switch on the Bluetooth®
speaker
2
Insert 3 x AAA batteries (supplied) into
the cartridge with correct polarity (+/-) as
indicated.
•
Press on the top of the Bluetooth®
speaker.
» The power indicator lights up white.
» The Bluetooth indicator flashes blue
slowly.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Push back the battery cartridge, then close
the battery compartment.
Note
• If you are not going to use the microphone for a long
time, remove the batteries.
• New batteries installed in the microphone support up
to 30 hours of continuous use.
• When the power indicator flashes red, it indicates that
the power level is low and you need to replace the
batteries.
8
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Slide the OFF/ON switch on the wireless
microphone to the ON position, then
select a song from the app and tap Sing ->
RECORD.
4 Play
» The wireless microphone starts to
pair with the Bluetooth® speaker
automatically.
» After successful pairing and connection,
the Bluetooth® indicator turns solid
blue.
Sing along through the
wireless microphone
Note
• The effective operation range between the wireless
microphone and Bluetooth® speaker is approximately
10 meters (30 feet).
1
Dock your iPad onto the Bluetooth®
speaker.
» A prompt pops up on the iPad screen,
asking you to install the relevant app.
5
Find and download a tutorial from
StarMaker Karaoke + Auto-Tune®, then
tap Sing->RECORD for how to sing along
through the wireless microphone and
Bluetooth® speaker.
2
3
Tap YES on the prompt to install the app
(StarMaker Karaoke + Auto-Tune®) from
Apple App Store.
After successful installation, run StarMaker
Karaoke + Auto-Tune® on the iPad.
6
Select a song from StarMaker Karaoke +
Auto-Tune® and sing along through the
wireless microphone.
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Play from a Bluetooth®
enabled device
Note
• The effective operation range between the Bluetooth®
speaker and your Bluetooth® enabled device is
approximately 10 meters (30 feet).
• To pair with a Bluetooth® enabled mobile device, make
sure that: no iPad is docked; or you have stopped music
play and exited StarMaker Karaoke + Auto-Tune® on
your docked iPad.
7
Use -/+ on the top of the Bluetooth®
speaker to adjust volume.
• To pair with a new mobile device, you can press to
remove the existing Bluetooth® connection.
• To play from a Bluetooth® enabled device, make sure
that you are not playing music from your iPad docked
on the Bluetooth® speaker.
Note
• If no prompt pops up on your iPad at step 1, you can
go to Settings -> General -> About -> AEA7100 ->
Find App for Accessory to install the app.
1
Press on the top of the Bluetooth®
speaker.
» The Bluetooth® indicator flashes blue
Tip
quickly.
• If automatic pairing fails, press and hold on the
speaker for more than 10 seconds to pair the
microphone with the speaker manually.
• If the wireless microphone remains disconnected from
the Bluetooth® speaker for more than 15 minutes, it
switches to standby mode automatically.To switch it
on again, you need to slide the OFF/ON switch on the
microphone to theOFF position and then slide back to
the ON position.
• You can use controls available on the app to adjust
sound effects.
• If you experience howling or echo, try to increase
the distance between the microphone and speaker
or adjust the angle of the microphone towards the
speaker.
2
Enable Bluetooth® on your device
that supports A2DP (Advanced Audio
Distribution Profile).
10 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Select ‘PHILIPS_AEA7100‘ on your
Bluetooth® enabled device (if necessary,
input ‘0000’ as the paring password).
» After successful pairing and connection,
the Bluetooth® indicator on the
speaker turns solid blue and the
speaker beeps twice.
Play and charge your iPad
through the dock connector
directly
Compatible iPad
This unit supports play and charge of the
following iPad models:
•
•
•
New iPad
iPad 2
iPad
Load the iPad
•
Dock your iPad.
4
Start music play on your Bluetooth®
enabled device.
To remove the iPad
Pull the iPad out of the dock.
•
Listen to the iPad
1
2
3
Make sure that the iPad has been loaded
correctly.
5
Use -/+ on the top of the Bluetooth®
speaker to adjust volume.
Start music play on your iPad.
» The connected iPad starts to play.
Use -/+ on the top of the Bluetooth®
speaker to adjust volume.
EN 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Charge the iPad
The docked iPad begins to charge as soon as
the unit is connected to AC power.
Play from an external device
You can also listen to an external audio player
through the Bluetooth® speaker.
AUDIO-IN
1
Connect a 3.5mm audio cable to:
•
the AUDIO-IN socket on the back of
the Bluetooth® speaker.
•
the headphone socket on an external
audio player.
2
3
Start music play on the external audio
player.
Use -/+ on the top of the Bluetooth®
speaker to adjust volume.
12 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions (W x H
x D)
5 Product
information
300 x 162 x 148mm
162 x 333 x 162mm
•
•
Speaker
Microphone
Weight
Note
1.3kg
0.3kg
•
•
Speaker
Microphone
• Product information is subject to change without prior
notice.
Specifications
Amplifier
Rated Output Power
Signal to Noise Ratio
Aux-in Link
2 X 5W RMS
>70dB
600 mV RMS, 20
kohm
Speakers
Speaker Impedance
Speaker Driver
Sensitivity
4 ohm
70mm full range
> 84dB/1m/1W
Bluetooth®
Bluetooth® version V2.1 + EDR
Frequency band
2.402-2.480 GHzISM
Band
Range
10m (free space)
General information
AC power
Operation Power
Consumption
120V~; 60 Hz
20 W
Standby Power
Consumption
<0.5W
EN 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Failed to set up connection between the
microphone and speaker
6 Troubleshooting
•
Check whether both the wireless
microphone and Bluetooth® speaker
are switched on.
Warning
• Never remove the casing of this device.
•
Make sure that the wireless
microphone and Bluetooth® speaker
are within the the effective operation
range, that is, approximately 10 meters
(30 feet).
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support).When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
•
Press and hold on the top of the
Bluetooth® speaker for more than 10
seconds to set up wireless connection
manually.
Howling or echo from the wireless
microphone
No power to the Bluetooth® speaker
•
•
Adjust volume.
•
•
•
Make sure that the AC power plug of the
device is connected properly.
Make sure that there is power at the AC
outlet.
As a power-saving feature, the speaker
switches to standby mode automatically
after staying idle for more than 15 minutes.
Switch on the speaker again (see ‘Switch
Increase the distance between the
microphone and speaker or adjust the
angle of the microphone towards the
speaker.
No response from the Bluetooth® speaker
•
Disconnect and reconnect the AC power
plug, and then switch on the device again.
No power to the wireless microphone
•
The batteries may be installed incorrectly
or drained. Install or replace the batteries
properly (see ‘Install/replace microphone
batteries’ on page 7).
•
As a power-saving feature, the microphone
switches to standby mode automatically
after staying disconnected from the
speaker for more than 15 minutes.To
switch it on again, you need to slide the
OFF/ON switch on the microphone to the
OFF position and then back to the ON
position.
No sound or poor sound
•
•
•
Adjust volume.
Check the Bluetooth® connection.
Check whether you have started music
play on the connected device.
14 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications are subject to change without notice
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
AEA7100_UM_17_V1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|