Philips Iron HI478 User Manual

HI478/IRON.FA 1/13/00 2:35 PM Page 1  
iron  
rem ovable water reser voir  
O ptinox stainless steel soleplate  
HI478  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HI478/IRON.FA 1/13/00 2:35 PM Page 2  
7. Do not allow cord to touch hot surfaces. Let the  
iron cool completely before putting away. Loop cord  
around cord wrap when storing.  
IMPO RTANT SAFEGUARDS  
When using your iron, especially when children are  
present, basic safety precautions should always be  
followed, including the following:  
8. When not in use, the Temperature Control should  
always be turned to Min position. Never yank cord to  
disconnect from outlet; instead, grasp plug and pull  
to disconnect.  
Read all instructions before using.  
1. Always disconnect iron from electrical outlet when  
filling removable water reservoir with water or  
emptying and when not in use. Be careful to avoid  
spilling water over the iron when filling reservoir.  
9. Do not use outdoors or operate where oxygen is  
being administered or in the presence of explosive  
and/or flammable fumes.  
2. Do not place or store iron where it can fall or be  
pulled into a tub or sink.  
10. Burns can occur from hot metal parts, hot water or  
steam. Use caution when you turn a steam iron upside  
down--there may be hot water in the internal reservoir.  
3. To protect against a risk of electrical shock, do not  
immerse the iron in water or other liquids.  
11. The iron may be cleaned by wiping with a damp  
cloth. Always unplug cord from outlet and allow  
iron to cool before cleaning.  
4. Close supervision is necessary for any appliance  
being used by or near children or invalids. Do not  
leave iron unattended while connected or on an  
ironing board. Always position iron carefully to  
prevent it from falling off or being knocked off ironing  
board, or if cord is pulled. When not in ironing  
position,always stand iron on heel rest.  
12. This appliance is intended for household use ONLY;  
it is not for commercial use or industrial use.  
13. For any service issues contact the retail location  
where product was purchased.  
14. IRO N MAY BE USED O NLY W ITH  
ALTERNATING CURRENT (AC). NEVER  
PLUG IRO N INTO A DIRECT CURRENT  
(DC) O UTLET.  
5. Use this appliance only for its intended use as described  
in this manual. Do not use attachments not  
recommended by Philips Electronics North America  
Corporation.  
6. Do not operate this appliance if it has a damaged  
cord or plug, if it is not working properly, if it has been  
dropped or damaged, or dropped into water.To avoid  
the risk of electric shock, do not disassemble the iron;  
return the iron to the retail location where it was  
purchased for examination and repair. Incorrect  
reassembly can cause a risk of electric shock when the  
iron is used.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HI478/IRON.FA 1/13/00 2:35 PM Page 4  
Table of Contents  
SPECIAL INSTRUCTIO NS  
1. To avoid a circuit overload, do not operate another  
high wattage appliance on the same circuit.  
Features  
2
Before Using  
For Dry Ironing  
3
2. If an extension cord is absolutely necessary, a 10-ampere  
cord should be used. Cords rated for less amperage  
may overheat. Care should be taken to arrange the  
cord so that it cannot be pulled or tripped over.  
3
Filling the Removable  
Water Reservoir  
3-4  
Setting the Temperature  
Steam Ironing  
4
SAVE THESE  
5
INSTRUCTIO NS  
Other Features  
5-6  
Self-Cleaning  
6-7  
SPECIAL PO LARIZED  
PLUG INSTRUCTIO NS  
Maintenance and Storage  
Temperature and Fabric Guide  
Problems  
7-8  
9
This Philips Iron has a polarized plug for an added safety  
feature.  
10  
For Assistance  
10  
Plug will fit into polarized outlet only one way.  
If plug does not properly fit outlet at first, reverse it.  
If plug still does not fit, contact a qualified electrician.  
Warranty  
Back Cover  
DO NOT ATTEMPT TO  
DEFEAT THIS SAFETY  
FEATURE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HI478/IRON.FA 1/13/00 2:35 PM Page 6  
2
3
Features  
Before Using  
Remove any sticker or protective foil from soleplate  
Dual Language  
Temperature  
Control Dial  
To ensure maximum steam performance,  
Clean any left over residue from the SteamVents by following this  
procedure:  
Amber  
Pilot Light  
Red Auto-Off  
Pilot Light  
Removable  
Water  
Reservoir  
Release Buttons  
1
2
3
Turn Steam Control to position 0.  
Fill iron (see section Filling the Removable Water Reservoir).  
Plug cord into electrical outlet. Set Temperature Control to  
maximum setting and allow iron to heat up for approximately  
2 minutes.  
Turn Steam Control to position 3-4.  
Hold iron over ironing board and allow to steam for 1 minute,  
dislodging any residue.  
Variable Steam  
Control  
4
5
Fabric  
Guide  
6
7
Iron over an old cotton towel (or other disposable non-  
synthetic cloth) for several minutes.  
Turn Steam Control to position 0 and Temperature Control to  
Min setting.  
Shot Of  
Steam Button  
Spray Button  
8
9
Let iron cool. Clean SteamVents.  
Iron is ready to use.  
For DryIroning
1
2
Plug cord into 120V AC outlet. Amber Pilot Light will glow.  
Always dry iron with Steam Control set at position 0 (Dry  
Setting).  
3
4
Be sure removable water reservoir is empty if you will be dry  
ironing for long periods of time.  
Preheat iron for approximately 2 minutes at proper  
temperature setting.  
NOTE: Iron must be on heel rest to preheat. If left to preheat with  
soleplate in down position, iron will automatically shut off after 30  
seconds before reaching desired temperature.  
Anti-Calc  
Filter  
Full Length  
Button Groove  
5
6
Begin ironing. When finished,stand iron in upright position on  
heel rest. Remove cord from electrical outlet.  
Allow iron to cool completely before storing.  
Removable Water  
Reservoir  
Self Clean  
Button  
Filling the Rem ovable W ater Reservoir  
• Drip Stop System  
Polished Optinox Soleplate  
with Special 39-Vent Bell Pattern  
ensures optimal and even steam  
distribution  
Automatically shuts off water  
Do not immerse the iron in water.  
supply if iron is to cool to steam.  
1
2
Unplug cord from electrical outlet.  
IMPO RTANT:  
When using your iron for the first time, you may notice a white  
deposit coming from the iron as it heats up.This is simply a residue  
left over from the final buffing of the iron soleplate. Follow the  
steps in “Before Using” to remove this residue.  
Set the Steam Control to position 0 (= no steam).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HI478/IRON.FA 1/13/00 2:35 PM Page 8  
4
5
Steam Ironing  
3
4
Press and hold the removable water reservoir release buttons  
and remove the removable water reservoir.  
BellVent Pattern on soleplate steams and presses twice in one  
action.  
Open the filling cap.  
Make sure that there is enough water in the removable water reservoir.  
1
Set the Temperature Control to the recommended position.  
See section 'Setting the temperature.'  
5
Pour tap water into the removable water reservoir up to the  
maximum level.  
2
Set the Steam Control to the appropriate steam position.  
- 1-2 for moderate steam (temperature settings  
- 3-4 for maximum steam (temperature settings  
to  
)
Do not fill the reservoir beyond the MAX indication.  
Wipe off any excess water before plugging iron into outlet.  
to MAX)  
6
Steaming will start as soon as the set temperature has been reached.  
If the tap water in your area is very hard, we advise you to mix it with  
an equal portion of distilled water, or to use distilled water only.  
Do not use vinegar, starch or chemically descaled water.  
O ther features  
7
Press to close the filling cap (click!) and put the removable  
water reservoir onto the iron.  
Spraying  
To remove stubborn creases at any temperature, make sure that  
there is enough water in the removable water reservoir.  
Setting the tem perature  
1
2
3
Put the iron on its heel.  
1
Press the spray button a couple of times to moisten the fabric.  
Plug cord in electrical outlet.  
Set the Temperature Control to the required ironing temperature  
by turning it to the appropriate temperature indicator.  
- Check the garment label for the required ironing temperature:  
Synthetic fabrics (e.g. acrylic, viscose, polyamide, polyester)  
Silk  
Drip Stop System  
The Drip Stop System continuously monitors soleplate temperature  
and automatically shuts off water supply if iron is too cool to steam.  
Wool  
Cotton, linen  
Drip Stop System virtually eliminates water dripping from soleplate and  
onto your fabric.  
- If you do not know what kind of fabric(s) the garment is made of, try  
to determine the right ironing temperature by ironing a part that will  
be invisible when you wear the garment.  
- Silk,woolen and synthetic materials:iron the reverse side of the fabric  
to prevent shiny spots.To prevent stains, avoid using the spray function.  
- Start ironing the articles that require the lowest ironing temperature  
first, such as those made of synthetic fibers.  
IMPO RTANT:The iron will automatically stop steaming at insufficient  
temperatures.This is due to the Drip Stop Systems valve closing when  
the temperature of the soleplate is too cool to produce steam.  
4
Start ironing when the Amber Pilot Light has first gone out and  
then comes on again.  
The Amber Pilot Light will come on from time to time during ironing.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HI478/IRON.FA 1/13/00 2:35 PM Page 10  
6
7
Shot of Steam  
1
2
Always unplug cord from electrical outlet and set the Steam  
Control to position 0.  
This function can also be used when you hold the iron in vertical  
position.  
Fill the removable water reservoir to the maximum level.  
A powerful "shot" of steam helps remove stubborn creases.  
The Shot-of-Steam function can only be used at temperature settings  
Do not use vinegar or other descaling agents to self clean your iron.  
between  
and MAX.  
3
4
5
6
Plug cord in electrical outlet.  
1
Press and release the Shot-of-Steam button.  
Set the Temperature Control to MAX.  
Allow iron to heat up for two minutes.  
Wait for a while before using the button again to avoid spluttering.  
Never direct the steam towards people.  
Anti-Calc Filter  
Turn Temperature Control to Min and unplug iron when the  
Amber Pilot Light has gone out.  
The built-in Anti-Calc Filter reduces deposit of scale and helps  
prolong life of the iron.  
7
Hold the iron over the sink, press and hold the self-clean  
button and gently shake the iron.  
4
Steam and boiling water will come out of the soleplate. Impurities and  
scale (if any) will be flushed out.  
8
Release the self-clean button as soon as all the water in the  
reservoir has drained out.  
Auto-off  
Repeat the self-cleaning process if the iron still contains a lot of  
impurities.  
An electronic safety device will automatically switch off the iron if it has  
not been moved for a while.  
After self-cleaning  
- Plug in the iron and reheat for 2 minutes.This will enable interior of  
the iron to dry before storing.  
To indicate that the iron has been switched off, the Red Auto-  
Off Pilot Light will start blinking.  
In a horizontal position, this will happen after 30 seconds.  
In a vertical position, this will happen after 8 minutes.  
- Unplug the iron when the Amber Pilot Light has gone out.  
- Move the hot iron gently over a piece of used cloth to remove any  
water stains that may have formed on the soleplate.  
- Let the iron cool down completely before you store it.  
To heat up the iron again:  
- Pick up the iron or move it slightly.  
- The Red Auto-Off Pilot Light will go out.The Amber Pilot Light will  
come on.  
- When the Amber Pilot Light has gone out and comes on again, the  
iron is ready for use.  
Maintenance and Storage  
1
Set the Temperature Control to Min position. Unplug cord  
from electrical outlet and let the iron cool down completely.  
2
Wipe scale and any other deposits off the soleplate with a  
damp cloth and a non-abrasive (liquid) cleaner.  
Self-Cleaning  
The self-clean function removes scale and impurities.  
Use the self-clean function once every two weeks. If the water in your  
area is very hard, the self-clean function should be used more  
frequently.  
Keep the soleplate smooth: avoid hard contact with metal objects.  
3
Regularly rinse the removable water reservoir with water.  
Empty the removable water reservoir after cleaning or before  
storing.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HI478/IRON.FA 1/13/00 2:35 PM Page 12  
8
9
Tem perature and Fabric Guide  
4
Loop cord around cord wrap when storing.  
Follow garment label instructions for best ironing results.Test iron temperature setting on an inside  
or small hidden section of garment before ironing.  
Always store the iron standing on its heel in a safe dry place.  
5
To clean body of iron, use mild detergent and soft cloth only.  
Never use harsh household cleansers, abrasive cleansers or  
Fabric guide located on the heel rest of iron gives temperature settings for most common fabrics.  
TEMP  
STEAM  
SETTING  
FABRIC  
IRO NING INSTRUCTIO NS  
scouring pads to clean iron housing  
scratching/fading of  
CO NTRO L  
SETTING  
Min  
housing colors may occur.  
0= Dry Iron  
Only  
Acetates  
Acrylics  
Acrilan*  
Creslan*  
Orlon*  
Sheer Synth  
Suede  
Turn Temperature Control to section marked Min.Start at the begin-  
ning of Min section and slowly increase temperature setting as need-  
ed to reach proper temperature.  
To clean and maintain  
polished Optinox soleplate  
Iron delicate fabrics on wrong side to avoid shining or glazing.If  
moisture is necessary, use a press cloth and MED setting.  
1
On a soft cloth, make a thin paste of abrasive household  
cleaner and water. Gently rub surface of soleplate to remove  
starch or residue build-up.  
Ultrasuede  
Nylons  
When pressing suede, use brown paper as press cloth and to cover  
ironing board.This will help prevent suede from rubbing off.  
Antron*  
Caprolan*  
Qiana*  
When pressing Ultrasuede* use a press cloth and press lightly on  
wrong side. Brush fabric lightly to remove press marks.  
2
Fill iron with water (see Section Filling the Removable Water  
Reservoir).  
3
4
5
Set Temperature Control to maximum setting.  
Allow iron to heat up approximately 2 minutes.  
Triacetates  
Arnel*  
When pressing some triacetates,a higher heat setting may be  
required.Slowly increase temperature as needed to reach proper  
temperature.  
Lo (•)  
Med  
0= Dry Iron  
Only  
Metallics  
Polyesters  
Dacron*  
Fortrel*  
Kodel*  
Trevira*  
Rayon  
Turn Temperature Control to section marked LO/MED (•).  
Start at the beginning of the LO/MED section for lightweight 100%  
synthetic permanent press fabrics.Some heavier polyester fabrics  
may require steam at positions 1 (LO) or 2 (MED) setting.Some  
durable silk fabrics may require a higher heat setting.Slowly increase  
setting as needed to reach proper temperature.  
Turn Steam Control to position 4 (MAX) and allow iron to  
steam for a few minutes.  
Pos.1= (LO)  
or  
Pos. 2= (MED)  
6
7
Iron over old cotton cloth to remove paste/cleanser from iron  
bottom and steam vents.  
Silk  
TurnTemperature Control to Min position and allow to cool  
completely. Unplug cord from electrical oulet and empty  
removable reservoir.  
Med (••)  
Hi (•••)  
Pos. 2= (MED)  
Pos. 3= (HI)  
Perm Press  
Polyester  
Cotton  
TurnTemperature Control to section marked MED (•).Turn Steam  
Control to Position 2 (MED). Most permanent press blends containing  
cotton require this setting.Test iron on inside seam or small hidden sec-  
tion of garment. If shine or color change occurs, use a press cloth.  
8
9
Should soleplate become scratched, most minor scratches can  
be removed using fine steel wool. After buffing, follow steps 2-  
6 before ironing on garments.  
Wool  
Cotton  
Turn Temperature Control to section marked HI (•••). Turn Steam  
Control to Position 3 (HI).  
When ironing wool,always use a press cloth and moisture. Never  
press wool dry.  
Wipe soleplate clean.  
Pos. 4= (MAX)  
Linen  
Turn Temperature Control to maximum setting.Turn Steam Control  
to position 4 (MAX).Lightly dampen fabric for thorough pressing.  
Iron dark colored fabrics on the wrong side to avoid shining.  
Ironing velvet or any other nap/sensitive fabric is not recommended. Be sure to check manufacturers label for care instructions.  
*Trademarks of fiber manufacturers.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HI478/IRON.FA 1/13/00 2:35 PM Page 14  
10  
Problem  
Possible cause(s)  
Solution  
No steam  
Not enough water in the removable  
water reservoir.  
Fill the removable water reservoir  
(see Filling the removable water  
reservoir).  
The steam control has been set to  
position 0.  
Set to steam position (see Steam  
ironing).  
FULL O NE YEARWARRANTY  
The iron is not hot enough and/or  
Drip Stop System is activated.  
Philips Electronics North America Corporation warrants each new  
Philips product,model HI478 (except cord),against defects in materials  
or workmanship for a period of one year from the date of purchase.  
Set the temperature control to the  
steam area (  
to MAX). Put the  
iron on its heel and wait until the  
Amber Pilot Light has gone out  
before you start ironing.  
IMPO RTANT: This warranty does not cover damage resulting  
from accident,misuse or abuse, lack of reasonable care, the affixing  
of any attachment not provided with the product or loss of parts or  
subjecting the product to any but the specified voltage.*  
PHILIPS ELECTRONICS NORTH AMERICA CORPORATIO N  
W ILL NOT PAY FOR UNAUTHORIZED SERVICE OF ANY  
TYPE.  
No Shot of Steam  
The Shot of Steam function has been Put the iron in horizontal position and  
used too often within a very short  
period.  
wait for a while before using the Shot  
of Steam function again.  
NO RESPONSIBILITY IS ASSUMED FO R ANY SPECIAL,  
INCIDENTAL OR CONSEQUENTIAL DAMAGES.  
The iron is plugged in  
but the soleplate is cold.  
The Auto-Off function has been  
activated.  
Move the iron slightly and the iron  
will start heating up again.  
In order to address warranty issues,simply take or ship the product  
back to the retail location where it was purchased.  
* Read enclosed instructions carefully.  
Check the cord, the plug and the  
electrical outlet.  
Connection problem.  
Manufactured for:  
Norelco Consumer Products Company  
A Division of Philips Electronics North America Corporation  
1010 Washington Blvd.,Stamford,CT 06912-0015  
For Assistance call 1-800-243-7884  
MADE IN SINGAPO RE.  
For assistance  
This symbol on the products nameplate means  
it is listed by Underwriters’ Laboratories,Inc.  
For assistance call toll free:  
PHILIPSand Philips Shield are Registered Trademarks of Koninklijke  
Philips Electronics N.V.  
1-800-243-7884  
or visit our website: www.philipsonline.com .  
Optinox is a Trademark of Koninklijke Philips Electronics N.V.  
Drip Stop is a Registered Trademark of Philips Electronics North  
America Corporation.  
© 2000 Philips Electronics North America Corporation.  
All Rights Reser ved.  
HI478  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Paxar Printer TC6037PR User Manual
Philips CD Player ND1110 18 User Manual
Philips Headphones HC350 User Manual
Philips Work Light Plus Slimline 8 User Manual
Pitney Bowes Fax Machine DM230L User Manual
Planet Technology Cable Box 170S8FS User Manual
Polk Audio Car Speaker db351 User Manual
Polycom Webcam 1725 22886 001 A User Manual
Poulan Pole Saw 115261126 User Manual
Poulan Tiller 401423 User Manual