Always there to help you
Register your product and get support at
M2BT
Question?
Contact
Philips
User manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
EN
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Important safety
instructions
General information
To avoid damage or malfunction:
Caution
• Do not expose the headset to excessive heat.
• Do not drop your headset.
• Headset shall not be exposed to dripping or splashing.
• Do not allow your headset to be submerged in water.
• Do not use any cleaning agents containing alcohol,
ammonia, benzene, or abrasives.
Hearing Safety
• If cleaning is required use a soft cloth, if necessary
dampened with a minimum amount of water or diluted
mild soap, to clean the product.
• The integrated battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
Danger
• To avoid hearing damage, limit the time you use the
headset at high volume and set the volume to a safe
level.The louder the volume, the shorter the safe
listening time is.
About operating and storage temperatures
and humidity
•
Operate or store in a place where
temperature is between -15ºC (5ºF) and
55ºC (131ºF) (up to 90% relative humidity.
Battery life may be shorter in high or low
temperature conditions.
Be sure to observe the following guidelines
when using your headset.
•
•
Listen at reasonable volumes for
reasonable periods of time.
•
Be careful not to adjust the volume
continuously upwards as your hearing
adapts.
Compliance with EMF
•
•
Do not turn up the volume so high that
you can’t hear what’s around you.
You should use caution or temporarily
discontinue use in potentially hazardous
situations.
This product complies with all applicable
standards and regulations regarding exposure to
electromagnetic fields.
•
•
Excessive sound pressure from earphones
and headset can cause hearing loss.
Using the headset with both ears covered
while driving is not recommended and may
be illegal in some areas while driving.
For your safety, avoid distractions from
music or phone calls while in traffic or
other potentially dangerous environments.
•
2
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Your wireless
on-ear headset
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers, register your product
Pouch
With this Philips wireless on-ear headset, you
can:
•
•
•
•
enjoy convenient wireless handsfree calls;
enjoy and control wireless music;
switch between calls and music;
enjoy music on non-Bluetooth devices with
an audio cable.
Quick start guide
Other devices
What's in the box
A mobile phone or device (e.g. notebook, PDA,
Bluetooth adapters, MP3 players etc) which
supports Bluetooth and is compatible to the
Overview of your wireless
on-ear headset
Philips Bluetooth wireless on-ear headset M2BT
f
e
d
c
USB charging cable (for charging only)
b
a
Audio cable
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
g
a Audio cable jack
b Micro USB charging slot
c Microphone
d Volume/Track control button
e Call/Music button
f LED light
g NFC detection area
4
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
There are two ways to pair your headset with
your mobile phone:
3 Get started
•
•
Manual pairing
NFC pairing
Charge your headset
Manual pairing
1 Make sure that the headset is fully charged
Note
and turned off.
• Before you use your headset for the first time, charge
the battery for 5 hours for optimum battery capacity
and lifetime.
• Use only the original USB charging cable to avoid any
damage.
• Finish your call before charging the headset, as
connecting the headset for charging will power the
headset off.
2 Press and hold the call/music button until
the blue and white LED flashes alternately.
» The headset remains in pairing mode
for 2 minutes.
3 Make sure that the mobile phone is turned
• You can operate the headset normally during charging.
on and its Bluetooth feature is activated.
4 Pair the headset with the mobile phone.
For detailed information, refer to the user
manual of your mobile phone.
Connect the supplied USB charging cable to:
•
the micro USB charging slot on the
headset and;
•
the charger/USB port of a computer.
NFC pairing
» LED turns white during charging and
turns off when the headset is fully
charged.
1 Make sure that the mobile phone is turned
on.
2 Make sure that the headset is fully charged
and turned off.
Tip
3 Press and hold the call/music button until
• Normally, a full charge takes 3 hours.
the blue and white LED flashes alternately.
• When your battery is empty, you can carry on listening
music with an audio cable. Make sure the headset is off
(and not in idle mode) before using this audio cable.
4 Make sure you turn on the NFC function
on your phone and your phone’s screen
remains active.
5 Place your phone over the headset so that
the NFC detection area of each device can
touch each other.
Pair the headset with your
mobile phone
6 Follow the pairing instructions of your
phone. Enter the password "0000" (4
zeros) if prompted.
Before you use the headset with your mobile
phone for the first time, pair it with a mobile
phone.A successful pairing establishes a unique
encrypted link between the headset and mobile
phone.The headset stores the last 8 devices
in the memory. If you try to pair more than 8
devices, the earliest paired device is replaced by
the new one.
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• Make sure your mobile phone has the NFC feature
available and switched on.
• Make sure your mobile phone is not in standby mode.
• Pairing with NFC is only suitable for Android mobile
operating system 4.2 or above.
• Refer to the user manual of your mobile phone to
identify its NFC detection area.
The following example shows you how to pair
the headset with your mobile phone.
1 Activate the Bluetooth feature of your
mobile phone, select Philips Fidelio M2BT.
2 Enter the headset password "0000" (4
zeros) if prompted. For those mobile
phones featuring Bluetooth 2.1+EDR or
higher, no need to enter a password.
10:35
10:36
10:37
Settings
Connectivity
Settings
Settings
Connectivity
Bluetooth
Devices Found
Enter Password
****
Philips Fidelio M2BT
Add
Bluetooth
device
0000
Select
Back
Select
Back
Select
Back
Multipoint
The headset has a Multipoint feature
which allows 2 devices to be connected
simultaneously and switched between each
other (see 'Manage your calls and music' on
Simply pause your music or video on one
device and play it on your second device, the
headphone will be connected to the playing
device automatically.
When you receive a phone call, the audio on
the first device will pause automatically to
receive the phone call on the second device.
The audio will resume when you finish you call.
6
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn the
headset off. hold for 4
seconds.
Play or
pause
Press and
• 1 long beep
• 1 long white
flash
4 Use your
headset
Press once. 1 short beep
music.
Connect the headset to a
Bluetooth device
Pick up/
hang up a
call.
Press once. 1 short beep
Reject an
incoming
call.
Redial the
last number.
Switch
caller
Press and
hold
1 short beep
1 Turn on your mobile phone/Bluetooth
device.
2 Press and hold the call/music button to
Press twice. 1 short beep
Press twice 1 long beep
turn the headset on.
» The blue LED flashes.
» The headset is reconnected to the
last two connected mobile phones/
Bluetooth devices automatically. If one
of them is not available, the headset
tries to reconnect to the second last
connected device.
during a
call.
Volume/Track control button
Adjust volume.
Skip forward.
Skip backward.
Slide up/
down
Press once 1 short
beep
Press twice 1 short
beep
N/A
Tip
• If you turn on the mobile phone/Bluetooth device or
activate the Bluetooth feature after turning on the
headset, you have to reconnect the headset and mobile
phone/Bluetooth device manually.
Mute/unmute the
microphone in a call.
Press
once
2 short
beeps
Other headset indicator status
Manage your calls and music
Headset status
Indicator
Call/Music button
The headset is connected
to a Bluetooth device,
while the headset in
standby mode or while you
are listening to music.
The headset is ready for
pairing.
The blue LED
flashes for every
8 seconds.
Task
Operation
Sound or LED
indicator
• 1 short beep
• 3 white flashes:
battery low <
25%
• 2 white flashes:
battery level <
50%
• 1 blue flash:
battery level >
50%
Turn the
Press and
headset on. hold for 2
seconds.
The LED flashes
blue and white
alternately.
The blue LED
flashes quickly.
The headset is on but not
connected to a Bluetooth
device.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
headset when you use it with the audio cable.
Connect the supplied audio cable to
There is an incoming call.
The battery level is low.
The blue LED
flashes once per
second.
The white LED
flashes.
•
•
the headset and;
an external audio device.
The battery is fully charged. The white LED
is off.
Wear your headset
Adjust the headband to fit your head.
Tip
• After use, twist the headset for easy storage.
Use with the audio cable
Note
• Make sure that you turn off the Bluetooth headset
before connecting the audio cable.
With the supplied audio cable, you can use
the headset with non-Bluetooth devices or on
airplane. No battery power is required for the
8
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Technical data
•
Minimum 10 hours of music time or talk
time
•
•
•
Minimum 350 hours of standby time
Normal time for a full charge: 3 hours
Rechargeable Lithium-ion battery (230
mAh)
•
•
3.5 mm audio jack for corded headset
mode
Bluetooth 4.0, Bluetooth mono support
(Headset Profile - HSP, Hands-Free
Profile - HFP), Bluetooth stereo supported
(Advanced Audio Distribution Profile
- A2DP;AudioVideo Remote Control
Profile - AVRCP)
•
Operating range: Up to 15 meters (50
feet)
•
•
•
Digital echo & noise reduction
Supports SBC,AAC and aptX® audio
Auto power off
Note
• Specifications are subject to change without notice.
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
products and rechargeable batteries. Follow
local rules and never dispose of the product
and rechargeable batteries with normal
household waste. Correct disposal of old
products and rechargeable batteries helps
prevent negative consequences for the
environment and human health.
6 Notice
Declaration of conformity
Hereby,WOOX Innovations declares that this
product is in compliance with the essential
requirements and other relevant provisions
of Directive 1999/5/EC.You can find the
com.
Remove the integrated battery
Note
• Make sure the headset is disconnected from the USB
charging cable before removing the battery.
This product has been designed, tested and
manufactured according the European R&TTE
directive 1999/5/EC.
If there is no collection/recycling system for
electronic products in your country, you can
protect the environment by removing and
recycling the battery before disposing the
headset.
Disposal of your old product
and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
This symbol means that the product contains
a built-in rechargeable battery covered by
European Directive 2013/56/EU which cannot
be disposed of with normal household waste.
We strongly advise you to take your product to
an official collection point or a Philips service
centre to have a professional remove the
rechargeable battery.
Inform yourself about the local separate
collection system for electrical and electronic
10 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Trademarks
Bluetooth
The Bluetooth word mark and logos are owned
by the Bluetooth SIG, Inc. and any use of such
marks by WOOX Innovations Limited is under
license.
iPhone, iPad and iPodTouch are trademarks
of Apple Inc., registered in the U.S. and other
countries.
EN 11
Download from Www.Somanuals.com. All Manuals Search And Download.
My Bluetooth headset is connected to a
7 Frequently
Bluetooth stereo enabled mobile phone, but
music only plays on the mobile phone speaker.
Refer to the user manual of your mobile phone.
Select to listen to music through the headset.
asked questions
My Bluetooth headset does not switch on.
The battery level is low. Charge the headset.
The audio quality is poor and crackling noise
can be heard.
The Bluetooth device is out of range. Reduce
the distance between your headset and
Bluetooth device, or remove obstacles between
them.
I cannot pair my Bluetooth headset with a
mobile phone.
The Bluetooth is disabled. Enable the Bluetooth
feature on your mobile phone and turn on the
mobile phone before you turn on the headset.
The audio quality is poor when streaming
from the mobile phone is very slow, or audio
streaming does not work at all.
Make sure your mobile phone not only
supports (mono) HSP/HFP but also supports
Pairing does not work.
Make sure the headset is in pairing mode.
•
Follow the steps described in this user
manual (see 'Pair the headset with your
•
Make sure that the LED light flashes blue
and white alternately before you release
the on/off button. Do not stop holding the
button if you see the blue LED only.
I hear but cannot control music on my
Bluetooth device (e.g. play/pause/skip forward/
backward).
Make sure the Bluetooth audio source supports
The mobile phone cannot find the headset.
•
The headset may be connected to a
previously paired device.Turn off the
connected device or move it out of range.
Pairing may have been reset or the headset
has been previously paired with another
device. Pair the headset with the mobile
phone again as described in the user
manual (see 'Pair the headset with your
My headset does not work when the audio
cable is connected.
Microphone function will be deactivated if a
3.5mm audio cable is connected to the headset.
In such case, your headset is only for music
enjoyment.
•
When I pick up an incoming call from my
iPhone while there is an active call on another
phone, there is no sound from the second
phone call, what can I do?
To switch to the second call on the second
'Overview of your wireless on-ear headset' on
the first call will be muted.
Voice dialing or redialing does not work on
my mobile phone.
Your mobile phone may not support this
feature.
The other side cannot hear me on the mobile
phone.
The microphone is muted. Press volume/track
control button once to enable the microphone.
To switch back to the first phone call, press
12 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
How can I restore all original headset settings?
Press volume/track control button and call
music button until the LED flashing white for 5
times sequentially.
support.
EN 13
Download from Www.Somanuals.com. All Manuals Search And Download.
2014 ©WOOX Innovations Limited.All rights
reserved.
Philips and the Philips’ Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
and are used byWOOX Innovations Limited
under license from Koninklijke Philips N.V.
0890
UM_M2BT_00_EN_V1.0
wk1432
Download from Www.Somanuals.com. All Manuals Search And Download.
|