Operating Instructions
Manual de instrucciones
High Definition Plasma Display
Alta definición Pantalla de plasma
Model No.
Número de modelo.
TH-42PH10UKA
TH-50PH10UKA
TH-58PH10UKA
The illustration shown is an image.
Before connecting, operating or adjusting this product, please read these instructions completely.
Please keep this manual for future reference.
La ilustración mostrada es una imagen.
Antes de conectar, utilizar o ajustar este producto, lea completamente este manual de instrucciones;
y guárdelo para consultarlo en el futuro en caso de ser necesario.
English
Español
TQB2AA0766-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11) Only use attachments / accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart / apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15) To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Dear Panasonic Customer
Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment
from your new Plasma Display.
To obtain maximum benefit from your set, please read these Instructions before making any adjustments,
and retain them for future reference.
Retain your purchase receipt as well, and record the model number and serial number of your set in the
space provided on the rear cover of these instructions.
Table of Contents
Important Safety Instructions.................................. 3
FCC STATEMENT...................................................... 5
Safety Precautions................................................... 6
Maintenance.............................................................. 7
Accessories .............................................................. 8
Accessories Supplied.............................................. 8
Remote Control Batteries........................................ 8
Connections.............................................................. 9
PC Input Terminals connection.............................. 10
SERIAL Terminals connection............................... 11
HDMI connection................................................... 12
COMPONENT / RGB connection.......................... 12
Power ON / OFF ..................................................... 13
Basic Controls ........................................................ 14
On-Screen Menu Displays..................................... 16
Initial selections ..................................................... 18
Selecting the input signal ...................................... 18
Selecting the On-Screen Menu Language ............ 18
ASPECT Controls ................................................... 19
Adjusting POS. /SIZE ............................................. 20
MULTI PIP................................................................ 21
Advanced PIP.......................................................... 22
PICTURE Adjustments........................................... 23
ADVANCED SETTINGS........................................ 24
SOUND Adjustment................................................ 25
MUTE .................................................................... 25
Digital Zoom............................................................ 26
PRESENT TIME SETUP / SET UP TIMER.............. 27
PRESENT TIME SETUP....................................... 27
SET UP TIMER ..................................................... 28
SCREENSAVER (For preventing image retention) .. 29
Setup of SCREENSAVER Time ............................ 30
Reduces screen image retention........................... 30
SIDE BAR ADJUST............................................... 31
Reduces power consumption ............................... 32
Customizing the Input labels ................................. 32
SET UP for MULTI DISPLAY................................... 33
How to setup MULTI DISPLAY ............................. 33
How to set the Display location number
for each Plasma Display ....................................... 33
SEAM HIDES VIDEO Setting ............................... 35
ID Remote Control Function.................................. 35
SET UP for Input Signals ....................................... 36
COMPONENT / RGB IN SELECT......................... 36
3D Y/C FILTER...................................................... 36
COLOR SYSTEM / Panasonic AUTO ................... 37
3:2 PULLDOWN / VIDEO NR................................ 37
SYNC .................................................................... 38
REFRESH RATE................................................... 38
H-FREQ. (kHz) / V-FREQ. (Hz)............................. 38
Options Adjustments ............................................. 39
Weekly Command Timer ....................................... 43
Shipping condition................................................. 45
Troubleshooting ..................................................... 46
VIDEO/COMPONENT/RGB/PC input signals........ 47
Command list of Weekly Command Timer........... 48
Specifications......................................................... 49
PANASONIC PLASMA SCREEN Limited Warranty... 51
LIMITED WARRANTY STATEMENT....................... 52
Customer Service................................................... 53
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.
This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions:(1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC CAUTION:
To assure continued compliance, use only shielded interface cables when connecting to computer or
peripheral devices. Any changes or modifications not expressly approved by Panasonic Corporation of
North America could cause harmful interference and would void the user’s authority to operate this device.
FCC Declaration of Conformity
Model No. TH-42PH10UKA, TH-50PH10UKA, TH-58PH10UKA
Responsible Party:
Contact Source:
Panasonic Corporation of North America
One Panasonic Way 1F-10, Secaucus, NJ 07094
Panasonic Professional Display Company
Panasonic Plasma Concierge 1-800-973-4390
CANADIAN NOTICE:
This Class B digital apparatus complies with Canadian ICES-003.
Note:
Do not allow a still picture to be displayed for an extended period, as this can cause permanent image retention to
remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed in NORMAL mode.
Trademark Credits
• VGA is a trademark of International Business Machines Corporation.
• Macintosh is a registered trademark of Apple Computer, USA.
• S-VGA is a registered trademark of the Video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been fully
respected.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
CAUTION
This Plasma Display is for use only with the following optional accessories. Use with any other type of optional
accessories may cause instability which could result in the possibility of injury.
(All of the following accessories are manufactured by Panasonic Corporation.)
• Speakers ......................................................TY-SP42P8W-K (TH-42PH10UKA), TY-SP50P8W-K (TH-50PH10UKA),
TY-SP58P10WK (TH-58PH10UKA)
•Pedestal........................................................TY-ST07-K (TH-42PH10UKA, TH-50PH10UKA),
TY-ST08-K (TH-42PH10UKA, TH-50PH10UKA), TY-ST58-K (TH-58PH10UKA)
•Mobile stand..................................................TY-ST42PF3 (TH-42PH10UKA, TH-50PH10UKA), TY-ST58PF10
•Wall-hanging bracket (vertical)......................TY-WK42PV7
•Wall-hanging bracket (angled) ......................TY-WK42PR7
•Wall-hanging bracket (drawer type) ..............TY-WK42DR1 (TH-42PH10UKA, TH-50PH10UKA)
•Ceiling-hanging bracket ................................TY-CE42PS7 (TH-42PH10UKA, TH-50PH10UKA)
•BNC Component Video Terminal Board........TY-42TM6A
•BNC Composite Video Terminal Board.........TY-42TM6B
•BNC Dual Video Terminal Board...................TY-FB9BD
•RCA Component Video Terminal Board........TY-42TM6Z
•RCA Composite Video Terminal Board .........TY-42TM6V
•RGB (Digital) Terminal Board........................TY-42TM6D
•RGB Active Through Terminal Board ............TY-42TM6G
•PC Input Terminal Board...............................TY-42TM6P
•
Composite / Component Video Terminal Board..TY-42TM6Y
•SDI Terminal Board.......................................TY-FB7SD
•HD-SDI Terminal Board ................................TY-FB9HD
•HDMI Terminal Board....................................TY-FB8HM
•Dual HDMI Terminal Board ...........................TY-FB10HMD
•Touch Panel ..................................................TY-TP42P8-S (TH-42PH10UKA), TY-TP42P10S (TH-42PH10UKA),
TY-TP50P8-S (TH-50PH10UKA), TY-TP50P10S (TH-50PH10UKA),
TY-TP58P10S (TH-58PH10UKA)
•Ir Through Terminal Board ............................TY-FB9RT
•Wireless Presentation Board .......................TY-FB10WPU
•AV Terminal Box............................................TY-TB10AV
•Anti glare filter...............................................TY-AR50P9W (TH-50PH10UKA), TY-AR42P9W (TH-42PH10UKA),
TY-AR58P10W (TH-58PH10UKA)
•U/V Tuner Board with MATE I/F....................TY-FB9TU (TH-50PH10UKA, TH-58PH10UKA)
(Except for Canada and United States of America, only Mexico)
Always be sure to ask a qualified technician to carry out set-up.
Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard
unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from being
played with by young children, creating the potential risk of suffocation.
Clean the power cable regularly to prevent it from
When using the Plasma Display
becoming dusty.
Do not bring your hands, face or objects close to the
• Built-up dust on the power cord plug can increase
ventilation holes of the Plasma Display.
humidity which might damage the insulation and cause
• Top of the Plasma Display is usually very hot due to the
fire. Unplug the cord from the wall outlet and clean it
high temperature of exhaust air being released through
with a dry cloth.
the ventilation holes. Burns or personal injuries can
happen if any body parts are brought too close. Placing
This Plasma Display radiates infrared rays, therefore it
any object near the top of the display could also result in
may affect other infrared communication equipment.
heat damages to the object as well as to the Display if its
Install your infrared sensor in a place away from direct
ventilation holes are blocked.
or reflected light from your Plasma Display.
Be sure to disconnect all cables before moving the
Plasma Display.
Note:
Do not allow a still picture to be displayed for an extended
period, as this can cause a permanent image retention to
remain on the Plasma Display.
• Moving the Display with its cables attached might
damage the cables which, in turn, can cause fire or
electric shock.
Examples of still pictures include logos, video games,
computer images, teletext and images displayed in
NORMAL mode.
Disconnect the power plug from the wall outlet as a
safety precaution before carrying out any cleaning.
• Electric shocks can result if this is not done.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions / Maintenance
WARNING
Securely insert the power cord plug as far as it will go.
• If the plug is not fully inserted, heat may be generated
which could cause fire. If the plug is damaged or the
wall socket plate is loose, they should not be used.
Setup
Do not place the Plasma Display on sloped or unstable
surfaces.
• The Plasma Display may fall off or tip over.
Do not handle the power cord plug with wet hands.
• Doing so may cause electric shocks.
Do not place any objects on top of the Plasma
Display.
• If water spills onto the Plasma Display or foreign objects
get inside it, a short-circuit may occur which could
result in fire or electric shock. If any foreign objects get
inside the Plasma Display, please consult anAuthorized
Service Center.
Do not do anything that might damage the power cable.
When disconnecting the power cable, hold the plug,
not the cable.
• Do not make any modifications, place heavy objects on,
place near hot objects, heat, bend, twist or forcefully
pull the power cable. Doing so may cause damage to
the power cable which can cause fire or electric shock.
If damage to the cable is suspected, have it repaired at
an Authorized Service Center.
Do not cover the ventilation holes.
• Doing so may cause the Plasma Display to overheat,
which can cause fire or damage to the Plasma
Display.
If the Plasma Display will not be used for a long period
of time, unplug the power cord from the wall outlet.
Transport only in upright position!
• Transporting the unit with its display panel facing
upright or downward may cause damage to the internal
circuitry.
If problems occur during use
If a problem occurs (such as no picture or no sound),
or if smoke or an abnormal odor is detected from the
Plasma Display, unplug the power cord immediately.
• Continuous use of the Display under these conditions
might cause fire or permanent damage to the unit.
Have the Display evaluated at an Authorized Service
Center. Services to the Display by any unauthorized
personnel are strongly discouraged due to its high
voltage dangerous nature.
If using the pedestal (optional accessory), leave a space
of 3 15/16” (10 cm) or more at the top, left and right, 2 3/8”
(6 cm) or more at the bottom, and 2 3/4” (7 cm) or more at
the rear. If using some other setting-up method, leave a
space of 3 15/16” (10 cm) or more at the top, bottom, left
and right, and 2 3/4” (7 cm) or more at the rear.
AC Power Supply Cord
The Plasma Display is designed to operate on 110 - 127 V
AC, 50/60 Hz.
If water or foreign objects get inside the Plasma Display,
if the Plasma Display is dropped, or if the cabinet
becomes damaged, disconnect the power cord plug
immediately.
• A short may occur, which could cause fire. Contact an
Authorized Service Center for any repairs that need to be
made.
Do not use any power supply cord other than that
provided with this unit.
• Doing so may cause fire or electric shocks.
Maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which
neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface
is dry.
• Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may become
damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise
the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added
and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
• Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get
inside the unit, operating problems may result.
• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet
surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact
with articles made from rubber or PVC.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Accessories Supplied
Check that you have the Accessories and items shown
Operating
Instruction book
Remote Control
Transmitter
EUR7636070R
Batteries for the
Remote Control
Transmitter
(2 × AA Size)
Fixing bands × 2
AC cord
Remote Control Batteries
Requires two AA batteries.
1. Pull and hold the hook, then
open the battery cover.
2. Insert batteries - note correct
3. Replace the cover.
polarity ( + and -).
+
-
+
-
“AA” size
Helpful Hint:
For frequent remote control users, replace old batteries with Alkaline
batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.
Observe the following precautions:
1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
When connecting the speakers, be sure to use only the optional accessory speakers.
Refer to the speaker’s Installation Manual for details on speaker installation.
(Example: TH-42PH10UKA)
Speakers (Optional accessories)
1
2
1
Speaker
terminal (L)
2
Speaker
terminal (R)
AC cord connection (see page 13)
– AC cord fixing
Unplug the AC cord
Unplug the AC cord
pressing the two
knobs.
Plug the AC cord into the display unit.
Plug the AC cord until it clicks.
Note:
When disconnecting the AC cord, be
absolutely sure to disconnect the AC
cord plug at the socket outlet first.
Note:
Make sure that the AC cord is locked on both the left and right sides.
– Cable fixing bands
Secure any excess cables with bands as required.
Pass the attached cable To secure cables connected to Terminals, wrap the cable fixing band around them then
pass the pointed end through the locking block, as shown in the figure.
While ensuring there is sufficient slack in cables to minimize stress (especially
in the power cord), firmly bind all cables with the supplied fixing band.
fixing band through the clip
as shown in the figure.
To loosen:
To tighten:
Push the catch
Pull
Pull
2
1
R
AUDIO
L
P
R/CR/R
PB/CB/B Y/G
AUDIO
COMPONENT/RGB IN
PC IN
SERIAL
SLOT1
SLOT2
SLOT3
OptionalTerminal Dual HDMI Terminals COMPONENT/RGB IN and From EXTERNAL From SERIAL
Board Insert Slot (equivalent of Dual AudioINTerminals(equivalent monitor terminal
(covered) HDMITerminal Board of BNC Component Video on Computer
Terminal on
Computer
(see page 11)
(TY-FB10HMD))
(see page 12)
TerminalBoard(TY-42TM6A)) (see page 10)
(see page 12)
Note:
At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
PC Input Terminals connection
COMPUTER
AUDIO
PC IN
TH-42PS9
Conversion adapter
(if necessary)
Mini D-sub 15p
RGB
PC cable
Audio
Stereo plug
Connect a cable which matches
the audio output terminal on the computer.
Notes:
• Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC
input Terminal.
• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
•
The display resolution is a maximum of 768 × 768 dots (TH-42PH10UKA), 1,024 × 768 dots (TH-50PH10UKA, TH-58PH10UKA)
when the aspect mode is set to “NORMAL”, and 1,024 × 768 dots (TH-42PH10UKA), 1,366 × 768 dots (TH-50PH10UKA,
TH-58PH10UKA) when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be
possible to show fine detail with sufficient clarity.
• The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need
to make setting changes to the computer at the time of connection.
• Some PC models cannot be connected to the set.
• There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.
• The computer shown in the illustration is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified
frequency range.
• Component Input is possible with the pin 1, 2, 3 of the D-sub 15P Connector.
• Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT”
(when component signal connection) or “RGB” (when RGB signal connection). (see page 36)
Signal Names for Mini D-sub 15P Connector
Pin No.
Signal Name
R (PR/CR)
Pin No.
Signal Name
GND (Ground)
Pin No.
Signal Name
NC (not connected)
1
6
11
5
4
3
2
1
2
3
4
5
12
13
14
15
7
8
G (Y)
GND (Ground)
GND (Ground)
NC (not connected)
GND (Ground)
SDA
HD/SYNC
VD
10
9
8
7
6
15 14 13 12 11
B (PB/CB)
9
NC (not connected)
GND (Ground)
10
SCL
Pin Layout for PC Input
Terminal
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
SERIAL Terminals connection
The SERIAL terminal is used when the Plasma Display is controlled by a computer.
COMPUTER
1
2
3
4
5
6
7
8
9
SERIAL
RS-232C Straight cable
Pin layout for SERIAL Terminal
D-sub 9p
Notes:
• Use the RS-232C cable to connect the computer to the Plasma Display.
• The computer shown is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a
computer which is connected to this terminal.
The computer will require software which allows the sending and receiving of control data which satisfies the conditions
given below. Use a computer application such as programming language software. Refer to the documentation for the
computer application for details.
Communication parameters
RS-232C Conversion cable
Signal level
Synchronization method
Baud rate
RS-232C compliant
Details
R X D
T X D
D-sub 9-pin female
Asynchronous
9600 bps
None
2
3
5
Parity
Character length
Stop bit
GND
8 bits
1 bit
-
4
1
6
9
Non use
•
7
8
Flow control
Shorted
NC
•
Basic format for control data
Command
Command Parameter
The transmission of control data from the computer
starts with a STX signal, followed by the command,
the parameters, and lastly an ETX signal in that order.
If there are no parameters, then the parameter signal
does not need to be sent.
Control details
Power ON
Power OFF
Volume 00 - 63
Audio MUTE OFF
Audio MUTE ON
Input select (toggle)
Slot1 input
Slot2 input
Slot3 input
PON
POF
AVL
None
None
**
0
1
AMT
IMS
None
SL1
SL2
SL3
STX
C1 C2 C3
:
P1 P2 P3 P4 P5
ETX
Colon Parameter(s) End
(1 - 5 bytes) (03h)
Start
(02h)
3-character
command (3 bytes)
PC1
SL1A
SL1B
SL2A
SL2B
PC input
Slot1 input (INPUT1A)
Slot1 input (INPUT1B)
Slot2 input (INPUT2A)
Slot2 input (INPUT2B)
Notes:
• If multiple commands are transmitted, be sure to wait
for the response for the first command to come from
this unit before sending the next command.
• If an incorrect command is sent by mistake, this unit will
send an “ER401” command back to the computer.
• SL1A, SL1B, SL2A and SL2B of Command IMS are
available only when a dual input terminal board is
attached.
DAM
None
Screen mode select (toggle)
NORMAL (4 : 3)
ZOOM
NORM
ZOOM
FULL
JUST
SELF
FULL
JUST
Panasonic AUTO
With the power off, this display responds to PON command only.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
HDMI connection
This unit has terminal boards equivalent to Dual HDMI Terminal Board (TY-FB10HMD) and BNC Component Video Terminal
Board (TY-42TM6A) as standard equipment.
[Pin assignments and signal names]
Pin No.
Signal
Pin No.
Signal
T.M.D.S Clock
Shield
1
11
T.M.D.S Data2+
T.M.D.S Data2
Shield
T.M.D.S Data2-
T.M.D.S Data1+
T.M.D.S Data1
Shield
2
12
13
T.M.D.S Clock-
CEC
R
AUDIO
L
P
R/CR/R
PB/CB/B Y/G
3
4
COMPONENT/RGB IN
Reserved
(N.C. on device)
SLOT1
SLOT2
SLOT3
PC
14
5
6
7
15
16
T.M.D.S Data1-
T.M.D.S Data0+
SCL
SDA
T.M.D.S Data0
Shield
T.M.D.S Data0-
T.M.D.S Clock+
DDC/CEC
Ground
+5V Power
8
17
HDMI cables
9
10
18
19
Hot Plug Detect
3 1
19
HDMI
AV OUT
HDMI
AV OUT
2
18
4
Note:
DVD player
DVD player
Additional equipment and HDMI cables shown are not supplied
with this set.
COMPONENT / RGB connection
COMPONENT VIDEO OUT
P
R
Example of input signal source
DVD Player
RCA-BNC
adapter
plug
P
B
Y, PB, PR
OUT
,
Y
L
Digital TV-SET-TOP-BOX
(DTV-STB)
AUDIO
OUT
R
R
AUDIO
L
P
R/CR/R
PB/CB/B Y/G
COMPONENT/RGB IN
SLOT3
Computer
RGB Camcorder
or
Notes:
• Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT”
(when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 36)
• Additional equipment, cables and adapter plugs shown are not supplied with this set.
• SYNC ON G signal is needed. (see page 38)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Power ON / OFF
Connecting the AC cord plug to the Plasma Display.
Fix the AC cord plug securely to the Plasma Display.
(see page 9)
Connecting the plug to the Wall Outlet
Note:
When disconnecting theAC cord, be absolutely sure to disconnect
the AC cord plug at the socket outlet first.
TH-42PWD8
INPUT
MENU
/
V
O
L
+
/
ENTER/
Press the Power switch on the Plasma Display to turn the set
on: Power-On.
Power Indicator
Power Indicator: Green
Example: The screen below is displayed for a while after the
Plasma Display is turned on. (setting condition is an
example.)
Remote Control
Sensor
When the POWER is turned on for the first
time, the LANGUAGE selection screen is
displayed.
From the second time on, the screen
shown below is displayed for a while
(setting condition is an example).
OSD LANGUAGE
English (UK)
Deutsch
Français
Italiano
From the second time on, language selection
can be done from the setup menu. (see
page 18)
PC
Español
FULL
ENGLISH (US)
Select the desired language using the or
button and press the ACTION ( ) button.
Русский
Note:
SELECT
SET
Set with the remote control. Buttons on the
main unit are unavailable for this setting.
Press the
button on the remote control to turn the Plasma Display off.
Power Indicator: Red (standby)
Press the
button on the remote control to turn the Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the
when the Plasma Display is on or in standby mode.
switch on the unit,
Note:
During operation of the power management function, the power indicator turns
orange in the power off state.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Controls
Remote control sensor
Volume Adjustment
Volume Up “+” Down “–”
When the menu screen is
displayed:
“+”:press to move the cursor up
“–”:press to move the cursor down
(see page 16)
Enter / Aspect button
(see page 16, 19)
INPUT
MENU
/
VOL
+/
ENTER/
Main Power On / Off Switch
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu screen
will switch. (see page 16)
Power Indicator
The Power Indicator will light.
Normal Viewing
SOUND
PICTURE
POS. /SIZE
SET UP
• Power-OFF ....Indicator not illuminated (The unit
will still consume some power
as long as the power cord is still
inserted into the wall outlet.)
INPUT button
• Standby .........Red
(INPUT1, INPUT2, INPUT3 and PC selection)
• Power-ON......Green
(see page 18)
• DPMS.............Orange (With PC input signal
and during operation of PC’s
screensaver.)
N button (see page 20, 23, 24, 25)
POS. /SIZE button (see page 20)
PICTURE button (see page 23)
INPUT button
(INPUT1, INPUT2, INPUT3 and PC selection)
Press to select INPUT1, INPUT2, INPUT3 and PC input
SLOTS sequentially. (see page 18)
SURROUND button
The surround setting switches on and off each time
the SURROUND button is pressed.
The benefits of surround sound are enormous. You
can be completely enveloped in sound; just as if
you were at a concert hall or cinema.
Note:
Sound mute On / Off (see page 25)
Numeric buttons (see page 35)
The surround settings are memorized separately
for each AUDIO MENU (STANDARD, DYNAMIC,
CLEAR).
ASPECT button
Press to adjust the aspect. (see page 19)
ON
OFF
MULTI Window buttons (see page 21)
SURROUND ON
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Controls
Standby (ON / OFF) button
The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 13).
Press ON to turn the Plasma Display On, from Standby mode. Press OFF to turn the Plasma Display Off
to Standby mode.
R button (see page 17)
Press the R button to return to previous menu screen.
POSITION buttons
Status button
ACTION button
Press to make
selections.
Press the “Status” button to display the current system status.
PC
1
2
1
2
3
Input label
Aspect mode (see page 19)
Off timer
NORMAL
SOUND button
(see page 25)
The off timer indicator is
displayed only when the off
timer has been set.
OFF TIMER 90
3
SET UP button (see page 16, 17)
DIRECT INPUT buttons
Press the INPUT “1”, “2”, “3” or “PC” input mode selection button to
select the INPUT mode.
This button is used to switch directly to INPUT mode.
These buttons can only display the slot which is installed. If you press
the button whose slot is not installed, it automatically displays the current
input signal.
Notes:
•
Press
to switch the input mode between INPUT2A and INPUT2B.
• Image retention (image lag) may occur on the plasma display panel
when a still picture is kept on the panel for an extended period. The
function that darkens the screen slightly is activated to prevent image
retention (see page 46), but this function is not the perfect solution to
image retention.
Channel Adjustment
This button cannot be used for this model.
Volume Adjustment
Press the Volume Up “+” or Down “–” button to increase or decrease
the sound volume level.
OFF TIMER button
The Plasma Display can be preset to switch to stand-by after a fixed
period. The setting changes to 30 minutes, 60 minutes, 90 minutes and
0 minutes (off timer cancelled) each time the button is pressed.
30
60
0
90
When three minutes remain, “OFF TIMER 3” will flash.
The off timer is cancelled if a power interruption occurs.
Remote ID lock (see page 35)
Digital Zoom (see page 26)
Press to access
Digital Zoom.
This displays an enlargement of the designated part of the displayed
image.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Menu Displays
The MENU button on the unit can also be
pressed.
1
Press to select .
To PICTURE adjust menu
(see page 23)
PICTURE
1/2
NORMAL
NORMALIZE
INPUT
MENU
/
VOL +/
ENTER/
STANDARD
25
0
0
0
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
Each time the MENU button is pressed, the
menu screen will switch.
[ from the unit ]
TINT
SHARPNESS
Normal Viewing
SOUND
PICTURE
SETUP
5
INPUT
MENU
/
VOL +/
ENTER/
POS. /SIZE
PICTURE
2/2
NORMAL
2
1
COLOR TEMP
1
2
Press to select.
Press to access each adjust
screen.
OFF
ON
COLOR MANAGEMENT
ADVANCED SETTINGS
Press to select
“ON”.
SET UP
1/2
Press to enter
A D VA N C E D
SETTINGS.
SIGNAL
COMPONENT/RGB-IN SELECT
RGB
INPUT LABEL
POWER SAVE
STANDBY SAVE
POWER MANAGEMENT
AUTO POWER OFF
OSD LANGUAGE
PC
OFF
OFF
OFF
OFF
To ADVANCED SETTINGS
(see page 23, 24)
(
)
ENGLISH US
1/2
ADVANCED SETTINGS
NORMAL
NORMALIZE
0
0
BLACK EXTENSION
INPUT LEVEL
GAMMA
2.2
OFF
AGC
2/2
ADVANCED SETTINGS
0
0
0
0
0
0
W/B HIGH R
W/B HIGH G
W/B HIGH B
W/B LOW R
W/B LOW G
W/B LOW B
SET UP
2/2
SCREENSAVER
MULTI DISPLAY SETUP
SET UP TIMER
PRESENT TIME SETUP
To POS. /SIZE adjust menu (see page 20)
To SOUND adjust menu
(see page 25)
During “VIDEO (S VIDEO)”,
“COMPONENT” and “Digital”
input signal.
SOUND
During “RGB/PC” input signal.
POS. /SIZE
NORMAL
NORMALIZE
AUDIO MENU
BASS
STANDARD
0
POS. /SIZE
NORMAL
NORMALIZE
H-POS
NORMAL
NORMALIZE
H-POS
0
0
0
0
0
0
0
MID
TREBLE
0
0
0
0
H-SIZE
BALANCE
SURROUND
0
H-SIZE
V-POS
V-SIZE
V-POS
V-SIZE
CLOCK PHASE
OFF
MAIN
AUDIO OUT (PIP)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Menu Displays
Note:
Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting.
[ from the unit ]
2
Press to access
e a c h a d j u s t
screen.
INPUT
MENU
/
VOL +/
ENTER/
Press the R button to return
to previous menu.
Press to return to next menu screen.
To SIGNAL screen for VIDEO
(S VIDEO) (see page 36, 37)
To SIGNAL screen for
COMPONENT (see page 37) (see page 37, 38)
To SIGNAL screen for RGB
To SIGNALscreen for Digital
(see page 37, 38)
[
]
[
]
[
]
[
]
SIGNAL
VIDEO
SIGNAL
COMPONENT
SIGNAL
RGB
SIGNAL
Digital
3D Y/C FILTER (NTSC)
COLOR SYSTEM
3 : 2 PULLDOWN
Panasonic AUTO (4 : 3)
VIDEO NR
ON
AUTO
OFF
NORMAL
OFF
3 : 2 PULLDOWN
VIDEO NR
OFF
OFF
SYNC
3 : 2 PULLDOWN
VIDEO NR
3 : 2 PULLDOWN
VIDEO NR
AUTO
OFF
OFF
OFF
OFF
H-FREQ. 33.8
V-FREQ. 60.0
kHz
Hz
H-FREQ. 33.8
V-FREQ. 60.0
kHz
Hz
Note: “SIGNAL” setup menu displays a different setting condition for each input signal. (see page 18)
To setup SCREENSAVER
(See page 29-31)
SCREENSAVER
Press to select START TIME/ FINISH TIME (When TIME OF DAY
is selected).
PRESENT TIME OF DAY 15:00
START
WHITE BAR SCROLL
TIME OF DAY
6:15
FUNCTION
MODE
START TIME
FINISH TIME
Press to select SHOW DURATION/ SAVER DURATION (When
INTERVAL is selected).
SCREENSAVER
12:30
BRIGHT
OFF
PRESENT TIME OF DAY 15:00
START
SIDE BAR ADJUST
WOBBLING
WHITE BAR SCROLL
TIME OF DAY
6:15
FUNCTION
MODE
START TIME
FINISH TIME
PEAK LIMIT
OFF
Press to set up.
SCREENSAVER
12:30
PRESENT TIME OF DAY 15:00
START
SIDE BAR ADJUST
WOBBLING
PEAK LIMIT
BRIGHT
OFF
OFF
WHITE BAR SCROLL
FUNCTION
MODE
INTERVAL
12:00
3:00
BRIGHT
OFF
SHOW DURATION
SAVER DURATION
SIDE BAR ADJUST
WOBBLING
Press the R button to return to
“SET UP” menu.
SCREENSAVER
PRESENT TIME OF DAY 15:00
START
PEAK LIMIT
OFF
WHITE BAR SCROLL
FUNCTION
MODE
To setup MULTIDISPLAY screen. (See page 33)
INTERVAL
12:00
3:00
BRIGHT
OFF
SHOW DURATION
SAVER DURATION
SIDE BAR ADJUST
WOBBLING
MULTI DISPLAY SETUP
MULTI DISPLAY SETUP
HORIZONTAL SCALE
VERTICAL SCALE
SEAM HIDES VIDEO
LOCATION
OFF
× 2
× 2
OFF
A1
PEAK LIMIT
OFF
POWER ON SCREEN DELAY
ON
To SET UPTIMER selection
screen. (see page 27, 28)
SET UP TIMER
Press to select POWER ON
TIME / POWER OFF TIME.
PRESENT TIME OF DAY 10:00
SET UP TIMER
OFF
12:00
OFF
POWER ON FUNCTION
POWER ON TIME
POWER OFF FUNCTION
POWER OFF TIME
PRESENT TIME OF DAY 10:00
OFF
0:00
OFF
0:00
POWER ON FUNCTION
POWER ON TIME
POWER OFF FUNCTION
POWER OFF TIME
Press to set up POWER
ON TIME / POWER OFF
TIME.
18:00
To PRESENT TIME SETUP.
(see page 27)
SET UP TIMER
PRESENT TIME OF DAY 10:00
PRESENT TIME SETUP
OFF
12:00
OFF
POWER ON FUNCTION
POWER ON TIME
POWER OFF FUNCTION
POWER OFF TIME
PRESENT TIME OF DAY MON 99:99
SET
DAY
Press the R button to return to
“SET UP” menu.
MON
99:99
18:00
PRESENT TIME OF DAY
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial selections
Selecting the input signal
Select the input signals to be connected by installing the optional Terminal Boards.
Press to select the input signal to be played back from the
equipment which has been connected to the Plasma Display.
Input signals will change as follows:
INPUT1
INPUT2A
INPUT2B
INPUT3
PC
SLOT2 is for dual input so that you can select INPUT2A or
INPUT2B for INPUT2.
INPUT2A : HDMI signal terminal in SLOT2
INPUT2B : HDMI signal terminal in SLOT2
TH-42PS9
INPUT
MENU
/
VOL
+
/
ENTER/
Notes:
• Selecting is also possible by pressing the INPUT button on the unit.
• Input terminal will not be selected if the terminal board is not installed into the SLOT.
• Select to match the signals from the source connected to the component/RGB input
terminals. (see page 36)
INPUT
MENU
/
VOL +/
ENTER/
• In 2 screen display, the same input mode cannot be selected for the main picture and
sub picture.
Selecting the On-Screen Menu Language
Press to display the SET UP menu.
Press to select OSD LANGUAGE.
Press to select your preferred language.
Selectable languages
1/2
SET UP
SIGNAL
COMPONENT/RGB-IN SELECT
RGB
PC
English(UK)
Deutsch
Français
Italiano
Español
ENGLISH(US)
.......(Chinese)
.......(Japanese)
.......(Russian)
INPUT LABEL
POWER SAVE
OFF
OFF
OFF
OFF
STANDBY SAVE
POWER MANAGEMENT
AUTO POWER OFF
OSD LANGUAGE
(
)
ENGLISH US
Русский
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture.
Press repeatedly to move through the aspect options:
NORMAL
Panasonic AUTO
ZOOM
FULL
JUST
Note:
When selecting an input slot that attaches BNC Dual Video Terminal
Board (TY-FB9BD), Panasonic AUTO cannot be selected.
[from the unit]
The aspect mode changes each time the ENTER button
is pressed.
INPUT
MENU
/
VOL +/
ENTER/
[During MULTI PIP Operations]
• Picture and Picture, Picture in Picture :
NORMAL
FULL
• Others
: Aspect switching is not possible.
Notes:
• For PC signal input, the mode switches between “NORMAL”, “ZOOM” and “FULL” only.
• For a 1125 (1080) / 60i · 50i · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p signal input, the mode is
set to “FULL” mode, and switching is not possible.
• Panasonic AUTO can be selected only during Video signal input.
• The aspect mode is memorized separately for each input terminal.
Mode
Picture
Explanation
4
NORMAL will display a 4:3 picture at its standard 4:3 size.
NORMAL
NORMAL
3
4
4
4
4
16
16
16
16
ZOOM mode magnifies the central section of the picture.
ZOOM
ZOOM
FULL
JUST
3
3
3
3
9
9
9
FULL will display the picture at its maximum size but with slight
elongation.
FULL
JUST
JUST mode will display a 4:3 picture at its maximum size but with aspect
correction applied to the center of the screen so that elongation is only
apparent at the left and right edges of the screen. The size of the picture
will depend on the original signal.
The display will automatically become enlarged (depending on the
picture source), allowing you to view the picture at its maximum size.
Notes:
Panasonic AUTO
9
• PanasonicAUTO mode is designed to automatically adjust the aspect
ratio to handle a mix of 16:9 and 4:3 program material. Certain 4:3
program material, such as stock market data screens, may occasionally
cause the image size to change unexpectedly. When viewing such
programs, it is recommended that the ASPECT be set to NORMAL.
• If adjusting the PICTURE V-POS/V-SIZE in PanasonicAUTO with FULL
mode, the adjustment is not memorized. When exiting the mode, the
screen will return to a former adjustment.
For an elongated image Image is expanded
Panasonic
AUTO
4
Changes in
accordance with the
Panasonic AUTO
mode setting (see
page 37).
3
• PanasonicAUTO can not be selected while BNC Dual Video Terminal
Board (TY-FB9BD) is installed.
For a 4:3 image
Note: Do not allow the picture to be displayed in NORMAL mode for an extended period, as this can cause a permanent
image retention to remain on the Plasma Display Panel.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting POS. /SIZE
1
2
Press to display the POS. /SIZE menu.
Press to select H-POS / H-SIZE / V-POS / V-SIZE /
CLOCK PHASE.
Press to adjust POS. /SIZE.
3
During “VIDEO (S VIDEO)”,
“COMPONENT” and “Digital” input signal.
POS. /SIZE
4
Press to exit from adjust mode.
NORMAL
NORMALIZE
H-POS
0
0
0
0
Notes:
H-SIZE
V-POS
V-SIZE
• Adjustment details are memorized separately for different input signal formats.
(Adjustments for component signals are memorized for 525 (480) / 60i · 60p, 625
(575) / 50i · 50p, 1125 (1080) / 60i · 50i · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i,
750 (720) / 60p · 50p each, and RGB/PC/Digital signals are memorized for each
frequency.)
During “RGB / PC” input signal.
POS. /SIZE
• If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture position
will shift up or down. This picture position movement cannot be controlled by the
POS. /SIZE function.
• If adjusting the PICTURE V-POS / V-SIZE in Panasonic AUTO with FULL mode,
the adjustment is not memorized. When exiting the mode, the screen will return
to a former adjustment.
NORMAL
NORMALIZE
H-POS
0
0
0
0
0
H-SIZE
V-POS
V-SIZE
CLOCK PHASE
H-POS Adjust the horizontal position.
H-SIZE Adjust the horizontal size.
V-POS Adjust the vertical position.
V-SIZE Adjust the vertical size.
CLOCK PHASE
Eliminate the flickering and distortion.
(RGB/PC in mode)
NORMALIZE
Normalization)
Helpful Hint (
/
While the POS. /SIZE display is active, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTI PIP
Press repeatedly.
Each time pressing this button main picture and sub picture will be displayed
as follows below.
[Picture and Picture]
Main picture Sub picture
[Picture out Picture]
[Picture in Picture]
Main picture
Sub picture Main picture Sub picture
Normal
Viewing
B
A
A
A B
B
Press to swap main
picture and sub picture.
A
B
B
B A
A
[Example]
Main picture label is bright
Press to select the input mode.
Sub picture label is bright
Under main Picture and sub picture display, select the
picture which you would like to change input modes.
Notes:
• The sub picture sound is heard while a sub picture
operation is underway.
PC1
PC1
VIDEO2
VIDEO2
A
A
B
B
• The sub picture operation automatically returns to
the main picture operation if a sub picture operation
has not been performed for about 5 seconds or if
any of the remote control buttons is pressed (except
button).
Input modes switching is possible
Main picture label is changed Sub picture label is changed
VIDEO2
VIDEO1
PC1
VIDEO2
A
C
B
D
Press to change input signal.
Picture is changed
Press to move the sub picture.
Each time the location of the sub picture will be moved.
Notes:
• This button is effective only in the picture in picture.
• The sub picture may be hidden by the on screen display, depending on its position.
Notes:
• If “Input lock” in Options menu is set to other than “Off”, MULTI PIP function isn’t available.
• Sound output is from the picture which is selected in Audio OUT(PIP) (see page 25).
• In 2 screen display, the same input mode cannot be selected for the main picture and sub picture.
• The main picture and sub picture are processed by different circuits, resulting in a slight difference in the clarity of the
pictures. There may also be a difference in the picture quality of the sub picture depending on the type of signals displayed
on the main picture and depending on the 2-picture display mode.
• Due to the small dimensions of the sub pictures, these sub pictures cannot be shown in detail.
• Computer screen picture is displayed in a simplified format, and it may not be possible to discern details on them
satisfactorily.
•
Following combinations of two analog signals cannot be displayed simultaneously;
Component - Component, Component - PC (RGB), PC (RGB) - Component, PC (RGB) - PC (RGB)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PIP
1
2
Press to display the Setup menu.
Press to select “OSD Language”.
3
4
Press and hold until the Options menu is displayed.
Press to select Advanced PIP.
Options
1/3
Weekly Command Timer
Onscreen display
Initial INPUT
On
Off
Press to adjust the menu.
Off : Sets normal two screen display mode
(see page 21).
Off
Off
0
0
Initial VOL level
Maximum VOL level
INPUT lock
Button lock
Remocon User level
5
Off
Off
Off
Off
On : Sets Advanced PIP mode.
Advanced PIP
One screen Advanced PIP
6
Press to exit from
Options menu.
2
5
3
Sub screen 1 Main screen
(When Advanced PIP is On)
7
Press repeatedly.
Each time pressing this
6
4
button main picture and sub picture will be displayed as above.
Note:
To use
,
,
,
buttons for the screen operations, follow the procedures in the previous page.
Notes:
• Advanced PIP corresponding signal
Sub screen
Main screen
NTSC, PAL, SECAM (tuner, video)
640x480@60Hz, 852x480@60Hz, 1024x768@60Hz,
525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1366x768@60Hz (RGB, DVI, HDMI)
1125/50i, 1250/50i (Component Video, RGB, DVI, SDI, HDMI) 1280x768@60Hz (DVI)
• If “Input lock” in Options menu is set to other than “Off”, MULTI PIP function isn’t available.
• Sound output is from the picture which is selected in Audio OUT (PIP) (see page 25).
• In 2 screen display, the same input mode cannot be selected for the main picture and sub picture.
• The main picture and sub picture are processed by different circuits, resulting in a slight difference in the clarity of the
pictures. There may also be a difference in the picture quality of the sub picture depending on the type of signals displayed
on the main picture and depending on the 2-picture display mode.
• Due to the small dimensions of the sub pictures, these sub pictures cannot be shown in detail.
•
•
Computer screen picture is displayed in a simplified format, and it may not be possible to discern details on them satisfactorily.
Following combinations of two analog signals cannot be displayed simultaneously;
Component - Component, Component - PC (RGB), PC (RGB) - Component, PC (RGB) - PC (RGB)
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE Adjustments
1
2
Press to display the PICTURE menu.
Select to adjust each item.
Press to select the menu to adjust.
Select the desired level by looking at the picture behind
the menu.
Note:
Menu that cannot be adjusted is grayout.Adjustable menu changes
depending on signal, input and menu setting.
PICTURE
1/2
NORMAL
NORMALIZE
Press the left or right button to switch between modes.
STANDARD
CINEMA DYNAMIC
STANDARD
25
0
0
0
PICTURE MENU
PICTURE
BRIGHTNESS
COLOR
STANDARD
TINT
SHARPNESS
5
For viewing in standard (evening lighting) environments.
This menu selects the normal levels of BRIGHTNESS
and PICTURE.
PICTURE
2/2
NORMAL
OFF
ON
COLOR TEMP
COLOR MANAGEMENT
ADVANCED SETTINGS
DYNAMIC
For viewing in brighter environments.
This menu selects higher than normal levels of
BRIGHTNESS and PICTURE.
Press to select “ON”.
CINEMA
Ideal for movies.
Press to enter Advanced
settings.
ADVANCED SETTINGS ON
Enables fine picture adjustment at a professional
Note:
If you would like to change the picture and color of the selected
PICTURE menu to something else, adjust using the items in
the PICTURE menu. (see next page)
level (see next page).
1/2
ADVANCED SETTINGS
NORMAL
NORMALIZE
0
0
BLACK EXTENSION
INPUT LEVEL
GAMMA
2.2
OFF
Press the left or right button to switch between modes.
AGC
NORMAL
COOL
WARM
2/2
ADVANCED SETTINGS
0
0
0
0
0
0
W/B HIGH R
W/B HIGH G
W/B HIGH B
W/B LOW R
W/B LOW G
W/B LOW B
COLOR MANAGEMENT ON
Enables vivid color adjustment automatically.
ADVANCED SETTINGS OFF
Displays images with settings of the PICTURE menu.
NORMALIZE
Normalization)
Helpful Hint (
/
While the “PICTURE” menu is displayed, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE Adjustments
Notes:
Item
Effect
Adjustments
• “COLOR” and “TINT” settings cannot be
adjusted for “RGB/PC” and “Digital” input
signal.
PICTURE
Adjusts the proper picture contrast.
Less
More
•
You can change the level of each function
(PICTURE, BRIGHTNESS, COLOR, TINT,
SHARPNESS) for each PICTURE MENU.
Adjusts for easier viewing of dark
pictures such as night scenes and
black hair.
BRIGHTNESS
Darker
Brighter
• The setting details for STANDARD,
DYNAMIC and CINEMA respectively
are memorized separately for each input
terminal.
• The “TINT” setting can be adjusted
for NTSC signal only during “VIDEO
(S VIDEO)” input signal.
• In PICTURE, there is not a noticeable
change even when contrast is increased
with a bright picture or reduced with a dark
picture.
COLOR
TINT
Adjusts color saturation.
Less
Reddish
Less
More
Greenish
More
Adjusts for natural flesh tones.
Adjusts picture sharpness.
SHARPNESS
ADVANCED SETTINGS
Item
Effect
Details
BLACK
EXTENSION
Adjusts the dark shades of the image in gradation.
Less
Less
Down
OFF
Less
Less
Less
Less
Less
Less
More
Adjustment of parts which are extremely bright and hard to see.
(This cannot be adjusted when the input signal is Digital.)
INPUT
LEVEL
More
Up
GAMMA
AGC
S CURVE
2.0
2.2
2.5
Increases the brightness of dark signal automatically.
Adjusts the white balance for light red areas.
Adjusts the white balance for light green areas.
Adjusts the white balance for light blue areas.
Adjusts the white balance for dark red areas.
Adjusts the white balance for dark green areas.
Adjusts the white balance for dark blue areas.
ON
W/B HIGH R
W/B HIGH G
W/B HIGH B
W/B LOW R
W/B LOW G
More
More
More
More
More
More
W/B LOW B
Notes:
• Carry out “W/B” adjustment as follows.
1. Adjust the white balance of the bright sections using the “W/B HIGH R” , “W/B HIGH G” and “W/B HIGH B” settings.
2. Adjust the white balance of the dark sections using the “W/B LOW R” , “W/B LOW G” and “W/B LOW B” settings.
3. Repeat steps 1 and 2 to adjust.
Steps 1 and 2 affect each other’s settings, so repeat each step in turn to make the adjustment.
• The adjustment values are memorized separately for each input terminal.
• The adjustment range values should be used as an adjustment reference.
NORMALIZE
Normalization)
Helpful Hint (
/
On the remote control unit, while the “ADVANCED SETTINGS” menu is displayed, if either the N button is pressed at
any time or the ACTION ( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the
factory settings.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SOUND Adjustment
1
2
Press to display the SOUND menu.
Select to adjust each item.
Press to select the menu to adjust.
Select the desired level by listening to the sound.
BASS
Adjusts low pitch sounds
SOUND
STANDARD
Emits the original sound.
Accentuates sharp sound.
Attenuates human voice.
NORMAL
NORMALIZE
AUDIO MENU
BASS
MID
TREBLE
BALANCE
SURROUND
AUDIO OUT (PIP)
STANDARD
0
0
0
MID
DYNAMIC
CLEAR
Adjusts normal sounds
TREBLE
Adjusts pitch sounds
0
OFF
MAIN
BALANCE
Adjusts left and right volumes
SURROUND
Select On or Off
Selects main
picture sound.
(When main picture
sound is chosen.)
MAIN
INPUT1
PC
SUB
Selects PIP frame
sound.
(When PIP frame
sound is chosen.)
INPUT1
PC
Musical note is displayed on right side of the audio output screen label.
Notes:
• Press the SURROUND button to directly turn the surround effect ON and OFF. (see page 14)
• BASS, MID, TREBLE and SURROUND settings are memorized separately for each AUDIO MENU.
NORMALIZE
Normalization)
Helpful Hint (
/
While the “SOUND” menu is displayed, if either the N button on the remote control is pressed at any time or theACTION
( ) button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings.
MUTE
Useful when answering the phone or receiving unexpected visitors.
Press this button to mute the sound.
Press again to reactivate sound. Sound is also reactivated when power is turned off or
volume level is changed.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Zoom
This displays an enlargement of the designated part of the displayed image.
Display the operation guide.
1
EXIT
Press to access Digital Zoom.
The operation guide will be displayed.
1
During Digital Zoom, only the following buttons can be operated.
[Remote control]
[Unit]
POSITION /
ACTION button
INPUT
MENU
/
VOL +/
ENTER/
VOL button
VOL button
MUTE button
SURROUND button
OFF TIMER button
2
3
Select the area of the image to be enlarged.
Press on the enlargement location to select.
The cursor will move.
EXIT
2
Select the magnification required for the enlarged display.
Each time this is pressed, the magnification factor changes.
This is shown in the image being displayed.
× 1
× 2
× 3
× 4
Return to normal display (quit Digital Zoom).
4
Press to exit from the Digital Zoom.
Notes:
• When power goes OFF (including “Off Timer” operation), Digital Zoom terminates.
• The Digital Zoom function cannot be selected while in the following operation state:
“Multi-viewer” (Picture in Picture, Picture out Picture, Picture and Picture) operation. (see page 21)
• While Digital Zoom is in operation, “Adjusting POS. /SIZE” cannot be used.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESENT TIME SETUP / SET UP TIMER
The timer can switch the Plasma Display ON or OFF.
Before attempting Timer Set, confirm the PRESENT TIME OF DAY and adjust if necessary.
Then set POWER ON TIME / POWER OFF TIME.
1
Press to display the SET UP menu.
SET UP
1/2
Press to select SET UP TIMER or
PRESENT TIME SETUP.
SIGNAL
COMPONENT/RGB-IN SELECT
2
RGB
PC
OFF
OFF
OFF
OFF
INPUT LABEL
POWER SAVE
STANDBY SAVE
POWER MANAGEMENT
AUTO POWER OFF
OSD LANGUAGE
Press to display the SET UP TIMER screen or
PRESENT TIME SETUP screen.
(
)
ENGLISH US
SET UP
2/2
SCREENSAVER
MULTI DISPLAY SETUP
SET UP TIMER
PRESENT TIME SETUP
PRESENT TIME SETUP
Display the PRESENT TIME SETUP screen.
To set up DAY and PRESENT TIME OF DAY, follow the procedure described below.
Press to select DAY or PRESENT TIME OF DAY.
1
PRESENT TIME SETUP
PRESENT TIME OF DAY MON 99:99
SET
DAY
Press to set up DAY or PRESENT TIME OF DAY.
MON
99:99
button: Forward
button: Back
Notes:
PRESENT TIME OF DAY
• Pressing “ ” or “ ” button once changes PRESENT TIME OF DAY 1minute.
• Pressing “ ” or “ ” button continuously changes PRESENT TIME OF DAY by 15 minutes.
Press to select SET.
2
3
PRESENT TIME SETUP
PRESENT TIME OF DAY MON 99:99
SET
DAY
TUE
10:00
PRESENT TIME OF DAY
Press to store PRESENT TIME SETUP.
Notes:
• SET cannot be selected unless PRESENT TIME OF DAY is set.
• Unless setting the present time other than “99:99”, DAY setting is invalid.
Press to exit from PRESENT TIME SETUP.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESENT TIME SETUP / SET UP TIMER
SET UP TIMER
Display the SET UP TIMER SCREEN.
Press to select
POWER ON TIME / POWER OFF TIME.
SET UP TIMER
PRESENT TIME OF DAY 10:00
1
Press to set up POWER ON TIME / POWER OFF
TIME.
OFF
12:00
OFF
POWER ON FUNCTION
POWER ON TIME
POWER OFF FUNCTION
POWER OFF TIME
button: Forward
button: Back
18:00
Notes:
• Pressing “ ” or “ ” button once changes POWER ON TIME / POWER OFF TIME
1minute.
• Pressing “ ” or “ ” button continuously changes POWER ON TIME / POWER OFF
TIME by 15 minutes.
Press to select POWER ON FUNCTION
/ POWER OFF FUNCTION.
SET UP TIMER
2
PRESENT TIME OF DAY 10:00
ON
12:00
ON
POWER ON FUNCTION
POWER ON TIME
POWER OFF FUNCTION
POWER OFF TIME
Press to select ON.
18:00
3
Press twice to exit from SET UP.
Note:
Timer function will not work unless “PRESENT TIME OF DAY” is set.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREENSAVER (For preventing image retention)
Do not display a still picture, especially in NORMAL mode, for any length of time.
If the display must remain on, a SCREENSAVER should be used.
SET UP
SCREENSAVER
MULTI DISPLAY SETUP
SET UP TIMER
2/2
1
2
Press to display the SET UP menu.
Press to select the SCREENSAVER.
PRESENT TIME SETUP
Press to select the SCREENSAVER screen.
SCREENSAVER
NEGATIVE / SCROLL selection
PRESENT TIME OF DAY 99:99
3
4
START
FUNCTION
MODE
START TIME
FINISH TIME
SIDE BAR ADJUST
WOBBLING
PEAK LIMIT
WHITE BAR SCROLL
Press to select the FUNCTION.
OFF
6:15
12:30
BRIGHT
OFF
Press to select the desired function.
OFF
WHITE BAR SCROLL
NEGATIVE
WHITE BAR SCROLL : A white bar will scroll from left to right.
NEGATIVE : A negative image will be displayed on the screen.
SCREENSAVER
PRESENT TIME OF DAY 99:99
START
FUNCTION
MODE
MODE selection
WHITE BAR SCROLL
Press to select the MODE.
OFF
6:15
START TIME
FINISH TIME
12:30
SIDE BAR ADJUST
WOBBLING
PEAK LIMIT
BRIGHT
OFF
OFF
Press to select each mode items.
OFF
INTERVAL
TIME OF DAY
ON
: Operates when SHOW DURATION and SAVER DURATION are
set up and those times arrive.
: Operates when START TIME and FINISH TIME are set up and
those times arrive.
: Operates when START is selected and the ACTION ( ) button is
pressed.
START setting
5
SCREENSAVER
When the MODE is set to ON, press to select
START.
PRESENT TIME OF DAY 99:99
START
FUNCTION
MODE
WHITE BAR SCROLL
ON
6:15
12:30
BRIGHT
OFF
START TIME
FINISH TIME
SIDE BAR ADJUST
WOBBLING
PEAK LIMIT
OFF
Press to start SCREENSAVER.
The menu screen will disappear and the SCREENSAVER will be activated. To stop the
SCREENSAVER under ON, press the R button.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREENSAVER (For preventing image retention)
Setup of SCREENSAVER Time
After selecting TIME OF DAY or INTERVAL, the relevant Time Setup will become available for selection and the Operating
Time may be set. (Time cannot be set when “MODE” is “ON” or “OFF”.)
SCREENSAVER
PRESENT TIME OF DAY 15:10
SCREENSAVER
PRESENT TIME OF DAY 15:00
SCREENSAVER
PRESENT TIME OF DAY 99:99
START
FUNCTION
MODE
START TIME
FINISH TIME
START
FUNCTION
MODE
START
FUNCTION
MODE
START TIME
FINISH TIME
WHITE BAR SCROLL
TIME OF DAY
6:15
WHITE BAR SCROLL
INTERVAL
WHITE BAR SCROLL
OFF
6:15
12:00
3:00
BRIGHT
OFF
SHOW DURATION
SAVER DURATION
SIDE BAR ADJUST
WOBBLING
12:30
12:30
SIDE BAR ADJUST
WOBBLING
BRIGHT
OFF
SIDE BAR ADJUST
WOBBLING
BRIGHT
OFF
PEAK LIMIT
PEAK LIMIT
PEAK LIMIT
OFF
OFF
OFF
Press to select START TIME / FINISH TIME
(When TIME OF DAY is selected).
Press to select SHOW DURATION / SAVER
DURATION (When INTERVAL is selected).
SCREENSAVER
PRESENT TIME OF DAY 15:00
START
FUNCTION
MODE
START TIME
FINISH TIME
WHITE BAR SCROLL
TIME OF DAY
6:15
Press to setup.
button: Forward
button: Back
12:30
SIDE BAR ADJUST
WOBBLING
BRIGHT
OFF
Notes:
PEAK LIMIT
OFF
• Pressing “ ” or “ ” button once changes the Time 1minute.
[However, switching occurs every 15 minutes when Periodic Time is selected.]
• Pressing “ ” or “ ” button continuously changes the Time by 15 minutes.
SCREENSAVER
PRESENT TIME OF DAY 15:00
START
FUNCTION
SCREENSAVER
PRESENT TIME OF DAY 15:10
SCREENSAVER
PRESENT TIME OF DAY 15:00
WHITE BAR SCROLL
START
FUNCTION
MODE
START TIME
FINISH TIME
START
FUNCTION
MODE
INTERVAL
MODE
WHITE BAR SCROLL
TIME OF DAY
0:00
WHITE BAR SCROLL
INTERVAL
12:00
3:00
BRIGHT
OFF
SHOW DURATION
SAVER DURATION
SIDE BAR ADJUST
WOBBLING
0:00
0:00
BRIGHT
OFF
SHOW DURATION
SAVER DURATION
SIDE BAR ADJUST
WOBBLING
0:00
SIDE BAR ADJUST
WOBBLING
BRIGHT
OFF
PEAK LIMIT
OFF
PEAK LIMIT
PEAK LIMIT
OFF
OFF
Note: Timer function will not work unless “PRESENT TIME OF DAY” is set.
Reduces screen image retention
These functions prevent the occurrence of an “image retention” on the display when turned ON.
WOBBLING: Automatically shifts the display image (therefore unnoticeable to the eye) to prevent image retention of
sharper contour of image.
ON1:
ON2:
Shifts the image every 30 seconds.
Shifts the image at a dot level pitch depending on screen-detection.
PEAK LIMIT: Suppresses image contrast (peak brightness).
Note: When a still picture is viewed for an extended time, the screen may become slightly darker. (see page 46)
SET UP
SCREENSAVER
MULTI DISPLAY SETUP
SET UP TIMER
2/2
1
2
Press to display the SET UP menu.
Press to select “SCREENSAVER”.
PRESENT TIME SETUP
SCREENSAVER
Press to display SCREENSAVER menu.
PRESENT TIME OF DAY 99:99
START
FUNCTION
MODE
START TIME
FINISH TIME
SIDE BAR ADJUST
WOBBLING
Press to select “WOBBLING” or “PEAK LIMIT”.
WHITE BAR SCROLL
OFF
6:15
3
Press to select “ON1”, “ON2” or “OFF” (WOBBLING).
“ON” or “OFF” (PEAK LIMIT).
12:30
BRIGHT
OFF
PEAK LIMIT
OFF
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREENSAVER (For preventing image retention )
SIDE BAR ADJUST
side bars
Do not display a picture in NORMAL mode for an extended
period, as this can cause an image retention to remain on the
side bars on either side of the display field.
To reduce the risk of such an image retention, change the
brightness of the side bars.
NORMAL mode
image retention
This function may be applicable to the non-picture area.
Non picture area
Picture out Picture
Picture and Picture
Display the SCREENSAVER screen.
(Refer to the previous page, operation guide steps 1 and 2)
1
Press to select the SIDE BAR ADJUST.
SCREENSAVER
PRESENT TIME OF DAY 99:99
START
Press to select OFF, DARK, MID, BRIGHT.
OFF DARK MID BRIGHT
WHITE BAR SCROLL
FUNCTION
MODE
START TIME
FINISH TIME
OFF
6:15
12:30
SIDE BAR ADJUST
WOBBLING
PEAK LIMIT
BRIGHT
OFF
OFF
2
Press to exit from SCREENSAVER.
Notes:
• To reduce the occurrence of image retention, set the SIDE BAR ADJUST to BRIGHT.
• The side bar may flash (alternate black/white) depending on the picture being shown on the screen. Using Cinema mode
will reduce such flashing.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Reduces power consumption
• POWER SAVE:
When this function is turned ON, luminous level of the Plasma Display is suppressed, so
power consumption is reduced.
• STANDBY SAVE:
When this function is turned ON, power consumption of the microcomputer is reduced
during power supply standby (see page 13-15), so standby power of the set is reduced.
• POWER MANAGEMENT:
The unit power supply is turned ON or OFF depending on whether or not there is a signal
during PC input mode.
This function is enabled when it is turned ON. (Only during input from PC(Mini D-sub)
terminal)
• AUTO POWER OFF:
Equipment power supply is turned OFF when there is no signal.
When this is set to On, the power supply of the unit goes Off 10 minutes after the input
signals stop.
This function is effective for input signals except input from PC (Mini D-sub) terminal.
Press to select
“POWER SAVE”
“STANDBY SAVE”
“POWER MANAGEMENT”
“AUTO POWER OFF”.
SET UP
1/2
1
SIGNAL
COMPONENT/RGB-IN SELECT
RGB
INPUT LABEL
PC
POWER SAVE
OFF
OFF
OFF
OFF
STANDBY SAVE
POWER MANAGEMENT
AUTO POWER OFF
OSD LANGUAGE
Press to select “ON” or “OFF”.
2
3
On
Off
(
)
ENGLISH US
Note:
“POWER MANAGEMENT” and “AUTO POWER OFF” are
effective during normal viewing (one picture screen) only.
Press to exit from SET UP.
Customizing the Input labels
This function can change the label of the Input signal to be displayed.
Select the input signal which you would like to change its label before customizing
the Input labels. (see page 15, 18)
SET UP
1/2
SIGNAL
COMPONENT/RGB-IN SELECT
RGB
Press to select INPUT LABEL.
INPUT LABEL
POWER SAVE
STANDBY SAVE
POWER MANAGEMENT
AUTO POWER OFF
OSD LANGUAGE
PC
Press to change the INPUT LABEL.
OFF
OFF
OFF
OFF
(
)
ENGLISH US
Note:
While selecting a Input signal through Optional Terminal Board connected to Slot 1, Slot 2 and Slot 3, the Input label will
depend on each Optional Terminal Board.
INPUT LABELS for Slot 1, Slot 2, Slot 3 and Mini D-sub:
[Slot1 Input]
[Slot2 Input]
[Slot3 Input]
INPUT1/VIDEO1/COMPONENT1/RGB1/DIGITAL1/PC1/DVD1/CATV1/VCR1/STB1
INPUT2/VIDEO2/COMPONENT2/RGB2/DIGITAL2/PC2/DVD2/CATV2/VCR2/STB2
INPUT3/VIDEO3/COMPONENT3/RGB3/PC3/DVD3/CATV3/VCR3/STB3
[PC (Mini D-sub) input] PC/COMPONENT/RGB/DVD/STB
When BNC Dual Video Terminal Board (TY-FB9BD) is used, an “A” or “B” is added at the end of each input label, depending
on the input selected (see below).
Addition sign
Selected Input
“A”
“B”
Composite
S VIDEO
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP for MULTI DISPLAY
By lining up Plasma Displays in groups, for example, as illustrated below, an enlarged picture may be displayed across
all screens.
For this mode of operation, each plasma display has to be set up with a Display number to determine its location.
(Example)
group of 4 (2 × 2)
group of 9 (3 × 3)
group of 16 (4 × 4)
(see page 34 for more displays lineups.)
How to setup MULTI DISPLAY
1
2
Press to display the SET UP menu.
Press to select the MULTI DISPLAY SETUP.
SET UP
2/2
SCREENSAVER
MULTI DISPLAY SETUP
SET UP TIMER
PRESENT TIME SETUP
Press to display the “MULTI DISPLAY SETUP” menu.
Press to select the MULTI DISPLAY SETUP.
Press to select “ON” or “OFF”.
MULTI DISPLAY SETUP
3
MULTI DISPLAY SETUP
HORIZONTAL SCALE
VERTICAL SCALE
SEAM HIDES VIDEO
LOCATION
OFF
× 2
× 2
OFF
A1
ON
POWER ON SCREEN DELAY
How to set the Display location number for each Plasma Display
MULTI DISPLAY SETUP
Press to select HORIZONTAL SCALE.
4
5
MULTI DISPLAY SETUP
HORIZONTAL SCALE
VERTICAL SCALE
SEAM HIDES VIDEO
LOCATION
OFF
× 2
× 2
OFF
A1
ON
Press to select “× 1”, “× 2”, “× 3”, “× 4”.
POWER ON SCREEN DELAY
Press to select VERTICAL SCALE.
MULTI DISPLAY SETUP
Press to select “× 1”, “× 2”, “× 3”, “× 4”.
MULTI DISPLAY SETUP
HORIZONTAL SCALE
VERTICAL SCALE
SEAM HIDES VIDEO
LOCATION
OFF
× 2
× 2
OFF
A1
ON
POWER ON SCREEN DELAY
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP for MULTI DISPLAY
Press to select SEAM HIDES VIDEO.
MULTI DISPLAY SETUP
6
7
MULTI DISPLAY SETUP
HORIZONTAL SCALE
VERTICAL SCALE
SEAM HIDES VIDEO
LOCATION
OFF
× 2
× 2
OFF
A1
ON
Press to select “OFF”, “ON”.
POWER ON SCREEN DELAY
Press to select LOCATION.
MULTI DISPLAY SETUP
MULTI DISPLAY SETUP
HORIZONTAL SCALE
VERTICAL SCALE
SEAM HIDES VIDEO
LOCATION
ON
× 2
× 2
OFF
A1
Press to select the required arrangement number.
(A1-D4 : Refer to the following)
POWER ON SCREEN DELAY
ON
Display Number locations for each arrangement.
(Examples)
( 2 × 1)
( 2 × 3 )
( 4 × 2 )
( 4 × 4 )
POWER ON SCREEN DELAY
8
Turning the power on for the multiple displays system, each display is turned on with a time lag to reduce the power
load.
MULTI DISPLAY SETUP
Press to select POWER ON SCREEN DELAY.
MULTI DISPLAY SETUP
HORIZONTAL SCALE
VERTICAL SCALE
SEAM HIDES VIDEO
LOCATION
ON
× 2
× 2
OFF
A1
Press to select OFF or ON.
OFF: All the display turns on simultaneously.
ON: Each display turns on in the order of LOCATION.
Delay time=LOCATION (difference from A1) × 1 sec.
POWER ON SCREEN DELAY
ON
Example) Case of B2 in 4 × 2
A1, A2, A3, A4, B1, B2
5 sec.
Notes:
• This setting is valid when MULTI DISPLAY SETUP is ON.
• During this function is working, the power indicator is blinking green.
• This function also works when the power recovers from failure or after plugging off and in again the power cord.
If unplugging and plugging the power cord while the unit is in standby mode and the power is being supplied to the board,
each unit has time delay to start supplying the power to the attached board according to LOCATION, and the power
indicator lights up red first and it turns orange when the power starts being supplied to the board.
9
Press twice to exit from SET UP.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP for MULTI DISPLAY
SEAM HIDES VIDEO Setting
To show joints between displays.
To hide joints between displays.
Reference
Suitable for moving image display.
ON
Suitable for still image display.
Step 6, Page 34
OFF
ID Remote Control Function
You can set the remote control ID when you want to use this remote control on one of several different displays.
Switch
to
on the right side.
1
Press the
Press one of
Press one of
button on the remote control.
2
3
4
-
-
,
,
for the tens digit setting.
for the units digit setting.
Notes:
• The numbers in 2, 3 and 4 should be set up quickly.
• Adjustable ID number range is 0 - 99.
• If a number button is pressed more than two times, the first two numbers become the ID number for the remote
control.
ID remote control button operation
The operation is the same as normal remote control except for the
button.
ID Cancellation
Press
button on remote control. (This has the same effect as pressing the
,
,
buttons at the same time.)
Notes:
• Set the Remote ID “On” to operate the ID remote control.
If Remote ID is set to “On”, you can use the remote control without identical ID number during option menu display.
(see page 41)
• The ID remote control cannot be used when ID select is set to anything other than 0, and the remote control ID is not
the same as the ID select number (see page 41).
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP for Input Signals
COMPONENT / RGB IN SELECT
Select to match the signals from the source connected to the COMPONENT / RGB input terminals.
Y, PB, PR signals
“COMPONENT”
R, G, B, HD, VD signals
“RGB”
1
Press to display the SET UP menu.
Press to select the “COMPONENT / RGB-IN
SELECT”.
2
Press to select the desired mode.
COMPONENT
RGB
SET UP
1/2
SIGNAL
COMPONENT/RGB-IN SELECT
RGB
INPUT LABEL
POWER SAVE
STANDBY SAVE
POWER MANAGEMENT
AUTO POWER OFF
OSD LANGUAGE
PC
3
OFF
OFF
OFF
OFF
Press to exit from adjust mode.
(
)
ENGLISH US
Note:
Selection may not be possible, depending on which optional board is installed.
3D Y/C FILTER – For NTSC AV images
Select “SIGNAL” from the “SET UP” menu during VIDEO (S VIDEO) input signal mode.
(“SIGNAL [VIDEO]” menu is displayed.)
SET UP
1/2
Press to select the “3D Y/C FILTER (NTSC)”.
1
SIGNAL
COMPONENT/RGB-IN SELECT
RGB
PC
Press to set ON / OFF.
INPUT LABEL
POWER SAVE
OFF
OFF
OFF
OFF
STANDBY SAVE
POWER MANAGEMENT
AUTO POWER OFF
OSD LANGUAGE
(
)
ENGLISH US
Press ACTION ( ) button
2
[
]
SIGNAL
VIDEO
Press to exit from adjust mode.
3D Y/C FILTER (NTSC)
COLOR SYSTEM
3 : 2 PULLDOWN
Panasonic AUTO (4 : 3)
VIDEO NR
ON
AUTO
OFF
NORMAL
OFF
Note:
When ON, this setting only affects NTSC input signals.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP for Input Signals
COLOR SYSTEM / Panasonic AUTO
Select SIGNAL from the “SET UP” menu during VIDEO (S VIDEO) input
signal mode.(“SIGNAL [VIDEO]” menu is displayed.)
SET UP
1/2
SIGNAL
COMPONENT/RGB-IN SELECT
RGB
Press to select the “COLOR SYSTEM” or “Panasonic
AUTO”.
INPUT LABEL
PC
POWER SAVE
OFF
OFF
OFF
OFF
STANDBY SAVE
POWER MANAGEMENT
AUTO POWER OFF
OSD LANGUAGE
Press to select each function.
(
)
ENGLISH US
If the image becomes unstable:
With the system set on Auto, under conditions of low
level or noisy input signals the image may in rare
cases become unstable. Should this occur, set the
system to match the format of the input signal.
Press ACTION ( ) button
[
]
SIGNAL
VIDEO
3D Y/C FILTER (NTSC)
COLOR SYSTEM
3 : 2 PULLDOWN
Panasonic AUTO (4 : 3)
VIDEO NR
ON
AUTO
OFF
NORMAL
OFF
Mode
Function
COLOR SYSTEM Set the color system to match the input signal. When selecting “AUTO”, the color system is automatically
selected from NTSC/PAL/SECAM, however, M.NTSC signal is not displayed properly depending on
the attached terminal board. To display M.NTSC signal, select “M.NTSC” in COLOR SYSTEM.
AUTO
PAL
SECAM
M.NTSC
NTSC
Panasonic AUTO Set to “NORMAL” to view 4:3 images in an unchanged format when Panasonic AUTO is
(4 : 3 ) selected. If you would like to view 4:3 images in Just format, set to “JUST”.
Note:
Panasonic AUTO does not function when BNC Dual Video Terminal Board (TY-FB9BD) is used.
3:2 PULLDOWN / VIDEO NR
3:2 PULLDOWN: When ON, the display attempts to reproduce a more natural interpretation of sources such as movie
pictures, which are recorded at 24 frames per second.
SET UP
1/2
If the picture is not stable, turn the setting to OFF.
SIGNAL
COMPONENT/RGB-IN SELECT
RGB
Notes:
When ON, this setting only affects the following signal input:
• NTSC / PAL signal input during “VIDEO (S VIDEO)” input signal.
• 525i(480i), 625i(575i), 1125(1080)/60i signal input during “COMPONENT” input signal.
INPUT LABEL
POWER SAVE
STANDBY SAVE
POWER MANAGEMENT
AUTO POWER OFF
OSD LANGUAGE
PC
OFF
OFF
OFF
OFF
VIDEO NR: Automatically reduces unwanted picture noise.
Note:
(
)
ENGLISH US
VIDEO NR cannot be adjusted while a PC signal is being applied.
Press ACTION ( ) button
[
]
[
]
RGB
SIGNAL
VIDEO
SIGNAL
Press to select 3:2
PULLDOWN or VIDEO NR.
Press to set ON/OFF.
1
2
3D Y/C FILTER (NTSC)
COLOR SYSTEM
3 : 2 PULLDOWN
Panasonic AUTO (4 : 3)
VIDEO NR
ON
AUTO
OFF
NORMAL
OFF
SYNC
3 : 2 PULLDOWN
VIDEO NR
AUTO
OFF
OFF
H-FREQ. 33.8
V-FREQ. 60.0
kHz
Hz
[
]
[
]
Digital
SIGNAL
COMPONENT
SIGNAL
3 : 2 PULLDOWN
VIDEO NR
OFF
OFF
3 : 2 PULLDOWN
VIDEO NR
OFF
OFF
H-FREQ. 33.8
V-FREQ. 60.0
kHz
Hz
Press to exit from adjust mode.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP for Input Signals
SYNC
Select SIGNAL from the “SET UP” menu during RGB input signal.
SET UP
1/2
SIGNAL
COMPONENT/RGB-IN SELECT
RGB
Press to adjust.
1
INPUT LABEL
PC
POWER SAVE
OFF
OFF
OFF
OFF
STANDBY SAVE
POWER MANAGEMENT
AUTO POWER OFF
OSD LANGUAGE
(
)
ENGLISH US
Press ACTION ( ) button
2
[
]
SIGNAL
RGB
Press to exit from adjust mode.
SYNC
3 : 2 PULLDOWN
VIDEO NR
AUTO
OFF
OFF
Setting RGB sync signal
Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT
signal).
H-FREQ. 33.8
V-FREQ. 60.0
kHz
Hz
SYNC
SYNC
SYNC
AUTO
ON G
VBS
AUTO:The H and V sync or synchronized signal are automatically selected. If both
input, it is selected the H and V sync.
ON G: Uses a synchronized signal on the Video G signal, which is input from the
G connector.
VBS: Uses a synchronized signal of Composite Sync input, which is input from
the HD connector.
REFRESH RATE
This function sets the refresh rate of the display.
This menu is displayed when the input signal is 50 Hz system (50i, 50p, 25p, 24p, 24sF) of vertical scan rate.
100 Hz: Reduce screen flicker.
50 Hz: Enhance the resolution of moving images.
Note:
It is recommended to set to 100 Hz normally.
[
]
[
]
SIGNAL
VIDEO
SIGNAL
RGB
Press to select REFRESH RATE.
1
2
3D Y/C FILTER (NTSC)
COLOR SYSTEM
3 : 2 PULLDOWN
Panasonic AUTO (4 : 3)
VIDEO NR
SYNC
3 : 2 PULLDOWN
VIDEO NR
REFRESH RATE
AUTO
OFF
OFF
100 Hz
AUTO
OFF
NORMAL
OFF
100 Hz
Press to adjust.
H-FREQ. 33.8
V-FREQ. 60.0
kHz
Hz
REFRESH RATE
[
]
SIGNAL
COMPONENT
[
]
SIGNAL
Digital
3 : 2 PULLDOWN
VIDEO NR
REFRESH RATE
OFF
OFF
100 Hz
3 : 2 PULLDOWN
VIDEO NR
REFRESH RATE
OFF
OFF
100 Hz
Press to exit from adjust mode.
H-FREQ. 33.8
V-FREQ. 60.0
kHz
Hz
H-FREQ. (kHz) / V-FREQ. (Hz)
Displays the H (Horizontal) / V (Vertical) frequencies.
This display is valid only for RGB/PC and Digital input signal.
Display range:
H-FREQ. 33.8
V-FREQ. 60.0
kHz
Hz
Horizontal 15 - 110 kHz
Vertical
48 - 120 Hz
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
1
2
Press to display the Setup menu.
Press to select “OSD Language”.
3
4
Press and hold until the Options menu is displayed.
Press to select your preferred menu.
Press to adjust the menu.
Options
Weekly Command Timer
1/3
5
Onscreen display
Initial INPUT
Initial VOL level
Maximum VOL level
INPUT lock
Button lock
Remocon User level
Advanced PIP
On
Off
Off
Off
0
0
Off
Off
Off
Off
Press to exit from
Options menu.
6
Item
Effect
Adjustments
Weekly
Command
Timer
Sets Weekly Command Timer. (see page 43)
On: Displays all the following on screen.
• Power on display
• Input signal switch display
Onscreen
display
• No signal display
On
Off
• Mute and the remaining time of off-timer after was pressed.
Off: Hides all the items above from view.
Off
PC
INPUT1
INPUT2
INPUT3
Adjusts the input signal when the unit is turned on.
Notes:
• Only the adjusted signal is displayed. (see page 18)
• Signal can be displayed when the Terminal board is installed.
• This menu is available only when “INPUT lock” is “Off”.
Initial INPUT
• When a dual input terminal board is attached, A or B is displayed depending on the selected input
signal. (Ex. INPUT1A, INPUT1B)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
Options
1/3
Weekly Command Timer
Onscreen display
Initial INPUT
On
Off
Off
Off
0
0
Initial VOL level
Maximum VOL level
INPUT lock
Button lock
Remocon User level
Advanced PIP
Off
Off
Off
Off
Item
Effect
Adjustments
button to adjust the volume when the unit is turned on.
On
Press
Off
Off: Sets normal volume.
On: Sets your preferred volume.
Notes:
Initial VOL
level
Off
On
•
When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.
• You can hear the changed volume regardless of your volume setting before opening the options menu
if you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Press
button to adjust the maximum volume.
Off
On
Off: Sets auto maximum volume.
On: Sets your preferred maximum volume.
Notes:
Maximum VOL
level
Off
On
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” automatically
becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
•
You can hear the changed volume regardless of your volume setting before opening the options menu if you
adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
Off
PC
INPUT1
INPUT2
INPUT3
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 18).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
INPUT lock
• In two screen display mode, if anything other than “Off” is set, the value will be fixed as the value input
in the single screen display mode.
• When a dual input terminal board is attached, A or B is displayed depending on the selected input
signal. (Ex. INPUT1A, INPUT1B)
Off
MENU&ENTER
On
Off: All the buttons at the bottom of the main unit can be used.
MENU&ENTER:
Locks
and
buttons on bottom face of main unit.
ENTER/
MENU
On: Locks all the button on bottom face of main unit.
Sets Button lock with the unit buttons in the following procedure.
Button lock
Off: Press four times→Press
four times→Press four times→Press
four EtNiTmER/ es→Press
MENU&ENTER: Press
four ItNiPmUT es→Press four times→Press
ENTER/
INPUT
ENTER/
On: Press four times→Press
four times→Press four times→Press
ENTER/
ENTER/
Off
User1
User2
User3
Off: You can use all of the buttons on the remote control.
Remocon
User level
User1:You can only use
,
,
,
,
,
,
,
,
buttons on the remote control.
User2:You can only use
, buttons on the remote control.
User3:Locks all the buttons on remote control.
Off: Sets normal two screen display mode (see page 21).
On: Sets Advanced PIP mode (see page 22).
Notes:
Advanced PIP
Off
On
• When “INPUT lock” is “On”, you cannot use all the two screen display functions.
buttons are unavailable during Advanced PIP mode operation.
•
,
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
Options
2/3
Off-timer function
Initial Power Mode
ID select
Enable
Normal
0
Remote ID
Off
Serial ID
Off
Display size
Studio W/B
Off
Off
Studio Gain
Off
Item
Effect
Adjustments
Enable: Enables the “Off-timer function”.
Disable: Disables the “Off-timer function”.
Off-timer
function
Enable Disable
Note:
When “Disable” is set, the Off-timer is cancelled.
Normal
Standby On
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Normal: Power returns in as the same state as before the power interruption.
Standby: Power returns in standby mode. (Power Indicator : red/orange)
Initial Power
Mode
On:
Power returns in power On. (Power Indicator : green)
Note:
When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.
Sets panel ID number when panel is used in “Remote ID” or “Serial ID”.
Set value range: 0 - 100
ID select
(Standard value: 0)
Off: Disables ID remote control functions. You can use normal remote control operations.
On: Enable ID remote control functions.
Remote ID
Serial ID
Off
Off
On
On
Sets the panel ID Control.
Off: Disables external control by the ID.
On: Enables the external control by the ID.
Adjusts the image display size on screen.
Off: Sets the normal image display size on screen.
On: Sets the image display size approximately 95 % of the normal image display.
Off
On
Notes:
Display size
Off
On
• This setting is valid only when the input signals are as follows;
NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (BNC Dual Video Terminal Board (TY-FB9BD))
525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p,
1125/30p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when two screen display, digital zoom or Multi screen is selected.
• When “Display size” is set to “On”, “POS. /SIZE” adjustment cannot be used.
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.
Off: Nullify all the settings adjusted.
On: Sets the color temperature for TV studio.
Note: Valid only when the low is set as color temperature on screen adjustment.
Studio W/B
Studio Gain
Off
Off
On
On
Sharpens the contrast for a better view when a part of the image is too light to see.
Off: Disables “Studio Gain”.
On: Enables “Studio Gain”.
Note: This setting is valid only when the input signals are as follows:
Component Video, RGB (analog), SDI, HDMI
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
Options
3/3
Slot power
Off
Off
Off
V. lnstallation
Rotate
Serial Slot Select
Slot1
Item
Effect
Adjustments
Off
Auto
On
Off: Power is not transmitted to the slot power.
Auto: Power is transmitted to the slot power only when main power is on.
On: Power is transmitted to the slot power when main power is on or in the standby state.
Slot Power
Note: In some cases, power is transmitted to the slot power when main power is on or in the standby
state regardless of the slot power setting.
Off: Sets fan to the horizontal installation mode.
On: Sets fan to the vertical installation mode.
Notes:
• This functions when display is turned on.
• Turn up the power switch for the upward direction when you set Display vertically.
V.Installation
Rotate
Off
On
On
Off: Does not rotate the image.
On: Rotates the image 180 degrees.
Off
Slot1
Slot2
Slot3
Serial Slot
Select
Selects the slot which communicates serial.
Note: The setting of an external command can be set only from the fixed serial terminal. (see page 11)
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote
ID” adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the
button on main unit together with
button on the remote control and hold for more than 5 seconds. The
“SHIPPING” menu is displayed and the lock is released when it disappears.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
Weekly Command Timer
You can set 7-day timer programming by setting time and command.
Note:
Before setting Weekly Command Timer, set PRESENT TIME SETUP. (see page 27)
Press to select Function.
Options
1/3
1
Press to select “On”.
Weekly Command Timer
Onscreen display
On
Note:
Press ACTION ( ) button
• When Function is set to On, SET UP TIMER
(see page 28) is unavailable and INTERVAL
/ TIME OF DAY in MODE of SCREENSAVER
(see page 29) cannot be selected.
Weekly Command Timer
Function
Monday
On
Program1
Program3
---
Tuesday
Wednesday
Thursday
Friday
Program3
---
Program6
Program4
Saturday
Sunday
Program Edit
Press to select a day.
Weekly Command Timer
2
Press to select a program number.
On
Function
Monday
Tuesday
Wednesday
Thursday
Friday
Program1
Program3
---
Note:
• You can set the program from 1 to 7.
--- indicates unset.
Program3
---
Program6
Program4
Saturday
Sunday
Program Edit
Program number
Program3
---
Thursday
Friday
Saturday
Sunday
Press to select Program Edit.
3
Program6
Program4
Program Edit
Press to show the Program Edit screen.
Program Edit screen
Press to select Program.
1/8
Weekly Command Timer
4
Press to change the program numbers (1-7).
1
Program
8:00 PON
01
02
03
04
05
10:30 IMS:SL1
--:-- ---
--:-- ---
--:-- ---
12:00 DAM:ZOOM
9:12 AVL:10
--:-- ---
06
07
08
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
Press to select a command number.
5
Press to show the previous / next command
pages (1-8) of the selected program.
Press to show the command setting screen.
1/8
8/8
Weekly Command Timer
Program
Weekly Command Timer
Program
1
1
AVL:00
8:00 PON
57
58
59
60
61
20:00
01
02
03
04
05
06
07
08
DAM:NORM
10:30 IMS:SL1
--:-- ---
20:30
22:00 POF
--:-- ---
--:-- ---
--:-- ---
--:-- ---
--:-- ---
--:-- ---
--:-- ---
62
63
64
12:00 DAM:ZOOM
9:12 AVL:10
--:-- ---
Command (--- indicates unset)
Set time of timer(--:-- indicates unset)
Command numbers
Press to select Command No.
Command setting screen
6
7
Weekly Command Timer
Program
Press to select a command number.
1
Command No
02
10:30
Time
Command
IMS:SL1
Press to select Time / Command.
Press to set each item.
Time: Set the time to execute a command program.
Pressing “ ” or “ ” button once changes
“Time” 1 minute.
Weekly Command Timer
1
Program
02
10:30
IMS:SL1
Command No
Time
Command
Pressing “ ” or “ ” button continuously changes “Time” by 15 minutes.
Command:Select a command to execute at the set time. This unit has 64 commands to
set. (see page 48)
Notes:
•
Command is performed in order of execution time, regardless of the command number.
• If a command execution time overlaps with that of other commands, these commands
are performed in number order.
• Pressing , Time becomes --:-- and Command becomes ---.
Note:
• Press
to return to the previous screen.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Shipping condition
This function allows you to reset the unit to the factory setting.
1
Press to display the SET UP menu.
Press to select “OSD LANGUAGE”.
2
Press and hold till the SHIPPING menu is
displayed.
1/2
SET UP
3
4
SIGNAL
COMPONENT/RGB-IN SELECT
RGB
INPUT LABEL
POWER SAVE
STANDBY SAVE
POWER MANAGEMENT
AUTO POWER OFF
OSD LANGUAGE
PC
OFF
OFF
OFF
OFF
Press to select “YES”.
(
)
ENGLISH US
YES
SHIPPING
Press to confirm.
[from the unit]
1 Press the MENU button till the Setup menu is displayed.
2 Press the Volume Up “+” or Down “–” button to select “OSD LANGUAGE”.
3 Press and hold the ENTER button till the SHIPPING menu is displayed.
4 Press the Volume Up “+” or Down “–” button to select “YES”.
5 Press the ENTER button and wait for 10 sec.
Note:
Press the R button to return to SET UP menu when SHIPPING menu is displayed.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Checks
Picture
Sound
Electrical Appliances
Cars / Motorcycles
Fluorescent light
Interference
Noisy Sound
Volume
Normal Picture
No Picture
No Sound
No Sound
(Check whether the mute function has been activated on the remote control.)
Not plugged into AC outlet
Not switched on
PICTURE and BRIGHTNESS/Volume setting
(Check by pressing the power switch or stand-by button on the remote control.)
If a signal with a non-applicable color system format, or frequency is input, only the input
terminal indication is displayed.
No Picture
No Color
Normal Sound
Normal Sound
Color controls set at minimum level. (see page 23, 24)
COLOR SYSTEM (see page 37)
No remote control operations can be performed.
Check whether the batteries have discharged completely and, if they have not, whether they
were inserted properly.
Check whether the remote control sensor is exposed to an outdoor light or a strong fluorescent
light.
Check whether the remote control designed specifically for use with the unit is being used.
(The unit cannot be operated by any other remote control.)
A cracking sound is sometimes heard from the unit. If there is nothing wrong with the picture or sound, this is the sound of the cabinet undergoing
very slight contractions in response to changes in the room temperature. There are no adverse
effects on the performance or other aspects.
The top or bottom of the picture on the screen is cut Adjust the position of the picture on the screen.
off when I use the zoom function.
Areas at the top and bottom of the screen where When using a video software program (such as a cinema size program) with a screen wider
the image is missing appear when I use the zoom than one in the 16:9 mode, blank areas separate from the images are formed at the top and
function.
bottom of the screen.
I can hear sounds coming from inside the unit.
When the power is turned on, a sound of the display panel being driven may be heard: This is
normal and not indicative of malfunctioning.
This Plasma Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the type of input
signal. However, this is not a malfunction.
Plasma Display panel
Symptoms
Check
The screen darkens slightly when bright pictures with The screen will darken slightly when photos, still images of a computer or other pictures with
minimal movements are shown.
minimal movements are shown for an extended period. This is done to reduce image retention
on the screen and the shortening of the screen’s service life: It is normal and not indicative of
malfunctioning.
It takes a while for the picture to appear.
The unit digitally processes the various signals in order to reproduce esthetically pleasing
images. As such, it sometimes takes a few moments for the picture to appear when the power
has been turned on, when the input has been switched or when the images for the main picture
and sub picture on the two screens are swapped.
The edges of the images flicker.
Due to the characteristics of the system used to drive the panel, the edges may appear to flicker
in the fast-moving parts of the images: This is normal and not indicative of malfunctioning.
The brightness on both sides of images in NORMAL When viewing the side panels at the “BRIGHT” or “MID” setting, the brightness on both sides
mode changes.
may change depending on the kind of program shown: This is normal and not indicative of
malfunctioning.
Some parts of the screen do not light up.
The plasma display panel is manufactured using an extremely high level of precision technology,
however, sometimes some parts of the screen may be missing picture elements or have luminous
spots. This is not a malfunction.
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent
image retention to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images
displayed in NORMAL mode.
Note:
The permanent image retention on the Plasma Display resulting from fixed image use is not
an operating defect and as such is not covered by the Warranty.
This product is not designed to display fixed images for extended periods of time.
Image retention appears
Whirring sounds can be heard from the display unit. The display unit is fitted with a cooling fan to dissipate heat generated during normal use. The
whirring sound is caused by rotation of the fan and is not a malfunction.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO/COMPONENT/RGB/PC input signals
VIDEO input (HDMI)
Vertical
Horizontal
Dot clock
(MHz)
Number of Total number of Number of Total number of
Signal format
frequency (Hz) frequency (kHz)
active pixels
pixels
active lines
lines
1
VGA60
525/60p
625/50p
750/60p
750/50p
1,125/60i
1,125/50i
59.94
59.94
50.00
60.00
50.00
60.00
50.00
31.47
31.47
31.25
45.00
37.50
33.75
28.13
25.18
27.00
27.00
74.25
74.25
74.25
74.25
640
720
720
1,280
1,280
1,920
1,920
800
858
864
1,650
1,980
2,200
2,640
480
480
576
720
720
1,080
1,080
525
525
625
750
750
1,125
1,125
2
3
4
5
6
7
Audio signal Linear PCM : 48/44.1/32 kHz
Applicable input signals for Component / Mini D-sub 15P (Component) / RGB / Mini D-sub 15P (RGB) (* Mark)
Horizontal
frequency
(kHz)
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
27.00
33.75
28.13
27.00
31.25
31.46
31.47
37.86
37.50
43.27
31.47
35.16
37.88
48.08
46.88
53.67
48.36
56.48
60.02
68.68
67.50
60.00
85.94
63.98
79.98
91.15
75.00
81.25
37.64
48.36
35.00
49.72
68.68
Vertical
frequency
(Hz)
Dot clock
frequency
(MHz)
13.5
Component /
Mini D-sub 15P Mini D-sub 15P
(Component)
RGB /
Signal name
(RGB)
1
2
3
4
5
6
7
8
525 (480) / 60i
525 (480) / 60p
625 (575) / 50i
625 (575) / 50p
750 (720) / 60p
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
47.92
30.00
25.00
24.00
50.00
70.07
59.94
72.81
75.00
85.01
59.94
56.25
60.32
72.19
75.00
85.06
60.00
70.07
75.03
85.00
75.00
60.00
85.00
60.02
75.03
85.02
60.00
65.00
59.94
60.00
66.67
74.54
75.06
*
*
*
*
*
*
*
*
*
*
*
*
*
*
27.0
13.5
27.0
1
∗
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
74.25
74.25
74.25
74.25
74.25
74.25
74.25
74.25
74.25
25.17
25.18
31.5
31.5
36.0
33.54
36.0
40.0
750 (720) / 50p
1,125 (1,080) / 60i
1,125 (1,080) / 50i
1,125 (1,080) / 24sF
1,125 (1,080) / 30p
1,125 (1,080) / 25p
1,125 (1,080) / 24p
1,250 (1,080) / 50i
640 × 400 @70 Hz
640 × 480 @60 Hz
640 × 480 @72 Hz
640 × 480 @75 Hz
640 × 480 @85 Hz
852 × 480 @60 Hz
800 × 600 @56 Hz
800 × 600 @60 Hz
800 × 600 @72 Hz
800 × 600 @75 Hz
800 × 600 @85 Hz
1,024 × 768 @60 Hz
1,024 × 768 @70 Hz
1,024 × 768 @75 Hz
1,024 × 768 @85 Hz
1,152 × 864 @75 Hz
1,280 × 960 @60 Hz
1,280 × 960 @85 Hz
1,280 × 1,024 @60 Hz
1,280 × 1,024 @75 Hz
1,280 × 1,024 @85 Hz
1,600 × 1,200 @60 Hz
1,600 × 1,200 @65 Hz
1,066 × 600 @60 Hz
1,366 × 768 @60 Hz
Macintosh13” (640 × 480)
Macintosh16” (832 × 624)
Macintosh21” (1,152 × 870)
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
2
2
∗
∗
50.0
49.5
56.25
65.0
75.0
78.75
94.5
108.0
108.0
148.5
108.0
135.0
157.5
162.0
175.5
53.0
86.71
30.24
57.28
100.0
∗1: When selected the RGB format and 525p signal input to the Mini D-sub 15P terminal, it is recognized as VGA 60Hz signal.
∗2: When inputted VGA 60Hz format signal from the other than Mini D-sub 15P terminal, it is recognized as 525p signal.
Note: Signals without above specification may not be displayed properly.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Command list of Weekly Command Timer
No.
1
2
3
4
5
6
7
Command
AAC:MENCLR
AAC:MENDYN
AAC:MENSTD
AAC:SURMON
AAC:SUROFF
AMT:0
Control details
Audio Menu (Clear)
Audio Menu (Dynamic)
Audio Menu (Standard)
Surround (ON)
Surround (OFF)
Audio Mute (OFF)
Audio Mute (ON)
AMT:1
8
9
ASO:M
ASO:S
AVL:00
Audio out when PIP mode (Main Picture)
Audio out when PIP mode (Sub Picture)
Audio Volume (00)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
AVL:10
AVL:20
AVL:30
AVL:40
AVL:50
AVL:60
Audio Volume (10)
Audio Volume (20)
Audio Volume (30)
Audio Volume (40)
Audio Volume (50)
Audio Volume (60)
Aspect (FULL)
Aspect (JUST)
Aspect (NORMAL)
Aspect (Panasonic Auto)
Aspect (ZOOM)
Dual Picture mode (OFF)
Advanced PIP mode (1) (see page 22)
Advanced PIP mode (2) (see page 22)
Advanced PIP mode (3) (see page 22)
Advanced PIP mode (4) (see page 22)
Advanced PIP mode (5) (see page 22)
Advanced PIP mode (6) (see page 22)
Advanced PIP mode (OFF) (normal two screen display mode)
Advanced PIP mode (ON)
The location of the sub picture (lower right)
The location of the sub picture (lower left)
The location of the sub picture (upper left)
The location of the sub picture (upper right)
Dual Picture mode (Picture in Picture)
Dual Picture mode (Picture out Picture)
Swap main picture and sub picture when PIP mode
Dual Picture mode (Picture and Picture)
Input select (PC1) (Main Picture when PIP mode)
Input select (SLOT1) (Main Picture when PIP mode)
Input select (SLOT1A) (Main Picture when PIP mode)
Input select (SLOT1B) (Main Picture when PIP mode)
Input select (SLOT2) (Main Picture when PIP mode)
Input select (SLOT2A) (Main Picture when PIP mode)
Input select (SLOT2B) (Main Picture when PIP mode)
Input select (SLOT3) (Main Picture when PIP mode)
Sub Picture Input Select (PC1)
DAM:FULL
DAM:JUST
DAM:NORM
DAM:SELF
DAM:ZOOM
DWA:OFF
DWA:OVL1
DWA:OVL2
DWA:OVL3
DWA:OVL4
DWA:OVL5
DWA:OVL6
DWA:OVLOF
DWA:OVLON
DWA:PIN0
DWA:PIN1
DWA:PIN2
DWA:PIN3
DWA:PIP
DWA:POP
DWA:SWP
DWA:TWN
IMS:PC1
IMS:SL1
IMS:SL1A
IMS:SL1B
IMS:SL2
IMS:SL2A
IMS:SL2B
IMS:SL3
ISS:PC1
ISS:SL1
Sub Picture Input Select (SLOT1)
Sub Picture Input Select (SLOT1A)
Sub Picture Input Select (SLOT1B)
Sub Picture Input Select (SLOT2)
Sub Picture Input Select (SLOT2A)
Sub Picture Input Select (SLOT2B)
Sub Picture Input Select (SLOT3)
Screen Saver WHITE BAR SCROLL (OFF)
Screen Saver WHITE BAR SCROLL (ON)
Power OFF
ISS:SL1A
ISS:SL1B
ISS:SL2
ISS:SL2A
ISS:SL2B
ISS:SL3
OSP:SCR0
OSP:SCR1
POF
PON
Power ON
SSC:FNC0
SSC:FNC1
SSC:MOD0
SSC:MOD3
Screen Saver function (WHITE BAR SCROLL)
Screen Saver function (NEGATIVE)
ScreenSaver (Mode (OFF))
ScreenSaver (Mode (ON))
Picture Mute (OFF)
∗
∗
VMT:0
VMT:1
Picture Mute (ON)
Picture Mute cannot be unlocked by powering off/on with the remote control. Turn off and on again with the button on
the unit or enter the command VMT:0 to unlock Picture Mute.
∗
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
TH-42PH10UKA
Power Source
110 - 127 V AC, 50 / 60 Hz
Power Consumption
Power on
Stand-by condition
Power off condition
Plasma Display panel
380 W
Save OFF 0.7 W, Save ON 0.5 W
0.2 W
Drive method : AC type 42-inch,
16:9 aspect ratio
Screen size
36.3” (922 mm) (W) × 20.4” (518 mm) (H)
× 42” (1,057 mm) (diagonal)
786,432 (1,024 (W) × 768 (H))
[3,072 × 768 dots]
(No.of pixels)
Operating condition
Temperature
32 °F - 104 °F (0 °C - 40 °C)
20 % - 80 %
Humidity
Applicable signals
Scanning format
PC signals
525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 50i · 24p · 25p
· 30p · 24sF ···· SMPTE274M, 1250 (1080) / 50i
VGA, SVGA, XGA
SXGA, UXGA ···· (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
HDMI A-B
TYPE A Connector × 2
COMPONENT/RGB IN Y/G (BNC)
PB/B (BNC), PR/R (BNC)
with/sync 1.0 Vp-p (75 Ω)
0.7 Vp-p (75 Ω)
AUDIO IN (RCA PIN JACK × 2)
(HIGH-DENSITY MINI D-SUB 15PIN)
0.5 Vrms (high impedance)
Y or G with/sync 1.0 Vp-p (75 Ω)
Y or G without/sync 0.7 Vp-p (75 Ω)
PC IN
B/PB/CB: 0.7 Vp-p (75 Ω)
R/PR/CR: 0.7 Vp-p (75 Ω)
HD/VD: 1.0 - 5.0 Vp-p (high impedance)
0.5 Vrms (high impedance)
AUDIO IN (M3 JACK)
SERIAL
SPEAKERS (6 Ω)
Accessories Supplied
Remote Control Transmitter
Batteries
EXTERNAL CONTROL TERMINAL (D-SUB 9PIN) RS-232C COMPATIBLE
16W [8 W + 8 W] (10 % THD)
EUR7636070R
2 × AA Size
Fixing bands
TMME203 × 2
Dimensions (W × H × D)
Mass (weight)
40.2” (1,020 mm) × 24” (610 mm) × 3.5” (89 mm)
main unit only
with speakers
approx. 57.3 lbs
approx. 66.1 lbs
Note:
Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
TH-50PH10UKA
TH-58PH10UKA
Power Source
110 - 127 V AC, 50/60 Hz
Power Consumption
Power on
Stand-by condition
Power off condition
Plasma Display panel
505 W
660 W
Save OFF 0.6 W, Save ON 0.4 W
0.1 W
Drive method : AC type 58-inch,
16:9 aspect ratio
Save OFF 0.6 W, Save ON 0.4 W
0.1 W
Drive method : AC type 50-inch,
16:9 aspect ratio
Screen size
43.5” (1,106 mm) (W) × 24.5” (622 mm) (H)
× 50” (1,269 mm) (diagonal)
1,049,088 (1,366 (W) × 768 (H))
[4,098 × 768 dots]
50.7” (1,287 mm) (W) × 28.5” (723 mm) (H)
× 58” (1,476 mm) (diagonal)
1,049,088 (1,366 (W) × 768 (H))
[4,098 × 768 dots]
(No.of pixels)
Operating condition
Temperature
32 °F - 104 °F (0 °C - 40 °C)
Humidity
20 % - 80 %
Applicable signals
Scanning format
525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 50i · 24p · 25p
· 30p · 24sF ···· SMPTE274M, 1250 (1080) / 50i
VGA, SVGA, XGA
PC signals
SXGA, UXGA ···· (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
HDMI A-B
TYPE A Connector × 2
COMPONENT/RGB IN Y/G (BNC)
PB/B (BNC), PR/R (BNC)
with/sync 1.0 Vp-p (75 Ω)
0.7 Vp-p (75 Ω)
AUDIO IN (RCA PIN JACK × 2)
(HIGH-DENSITY MINI D-SUB 15PIN)
0.5 Vrms (high impedance)
Y or G with/sync 1.0 Vp-p (75 Ω)
Y or G without/sync 0.7 Vp-p (75 Ω)
PC IN
B/PB/CB: 0.7 Vp-p (75 Ω)
R/PR/CR: 0.7 Vp-p (75 Ω)
HD/VD: 1.0 - 5.0 Vp-p (high impedance)
0.5 Vrms (high impedance)
AUDIO IN (M3 JACK)
SERIAL
SPEAKERS (6 Ω)
Accessories Supplied
Remote Control Transmitter
Batteries
EXTERNAL CONTROL TERMINAL (D-SUB 9PIN) RS-232C COMPATIBLE
16W [8 W + 8 W] (10 % THD)
EUR7636070R
2 × AA Size
TMME203 × 2
Fixing bands
Dimensions (W × H × D)
Mass (weight)
47.6” (1,210 mm) × 28.5” (724 mm) × 3.7” (95 mm) 55.1” (1,399 mm) × 33.2” (843 mm) × 3.9” (99 mm)
main unit only
with speakers
approx. 79.4 lbs
approx. 88.2 lbs
approx. 119 lbs
approx. 130.1 lbs
Note:
Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
(for the U.S.A and Puerto Rico)
Panasonic Professional Display Company
Unit of Panasonic Corporation of
North America
One Panasonic Way 1F-10
Secaucus, NJ 07094
Panasonic Professional Flat Panel Display
Limited Warranty
Panasonic Professional Display Company. (referred to
antenna, inadequate signal pickup, maladjustment of
consumer controls, improper operation, power line surge,
improper voltage supply, lighting damage, or service by
anyone other than an authorized repair facility, or
damage that is attributable to acts of God.
as “the Warrantor”) will repair this product and all
included accessories with new or refurbished parts,
free of charge in the USA or Puerto Rico, of the
original purchase in the event of a defect in materials or
workmanship as follows:
LIMITS AND EXCLUSIONS
Part
Warranty
Labor
Warranty
Models or Parts
There are no express warranties except as listed above.
Professional Flat
Panel Display
2 Years
2 Years
THE WARRANTOR SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES
(INCLUDING, WITHOUT LIMITION, DAMAGE
TO DISCS) RESULTING FROM THE USE OF THIS
PRODUCT, OR ARISING OUT OF ANY BREACH OF
THE WARRANTY. ALL EXPRESS AND IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR
PARTICULAR PURPOSE, ARE LIMITED TO THE
APPLICABLE WARRANTY PERIOD SET FORTH
ABOVE.
On-site or carry-in service in the USA and Puerto Rico
may be obtained during the warranty period by contacting
Panasonic Professional Display Company Service toll free
at 1-800-973-4390.
This warranty is extended only to the original purchaser
and is non transferable. A purchase receipt or other
proof of date of original purchase will be required before
warranty service is rendered.
Some states do not allow the exclusion or limitation
of incidental or consequential damages, or limitations
on how long an implied warranty lasts, so the above
exclusions or limitations may nor apply to you. This
warranty gives you specific legal rights and you may
other rights, which vary from state to state.
This warranty only covers failures due to defects in
materials or workmanship, which occur during normal
use. The warranty does not cover damage which occur
in shipment, or failures which are caused by products
not supplied by the warrantor, or failures which result
from improper installation, set-up adjustments, improper
If you have a problem with this product that is not
handled to your satisfaction, then write the Consumer
Affairs Department at the Company address indicated
above.
In the USA and Puerto Rico
FOR SERVICE
CALL TOLL FREE
1-800-973-4390
51
Download from Www.Somanuals.com. All Manuals Search And Download.
(for Canada)
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
LIMITED WARRANTY STATEMENT
Panasonic Canada Inc. (also known as PCI) warrants this product to be free of
defects in material and workmanship under normal use during the applicable
warranty coverage period described below. PCI agrees to repair, or at its option,
exchange, any part that becomes defective. However, the product must be
purchased and serviced in Canada. The product or part that shows evidence of
defect must be delivered prepaid or carried in to an authorized Panasonic Broadcast
Service Center. This warranty does not cover shipping costs.
The warranty coverage period is one year for both parts and labour beginning with
the date of original end user purchase, subject to the exceptions as stated below.
Repaired or replacement parts supplied during the warranty coverage period carry
the unexpired portion of the original warranty coverage period. Proof of product
purchase is a condition of warranty service. The owner must produce the product
purchase receipt or other satisfactory evidence of date of original purchase.
WARRANTY COVERAGE PERIOD EXCEPTIONS
Item
Parts
Labour
N/A
Video Tape
30 days—Replacement only
(content not covered)
P2/SD Cards
Video Heads
(Content not covered)
1 year or 2,000 hrs. (prorated)
Whichever comes first
N/A
1 year or 2,000 hrs.
Whichever comes first
D5 Video heads
1 year or 1,000 hrs.
1 year or 1,000 hrs.
Whichever comes first
Whichever comes first
Maintenance Items
Colour Camera CCD
Imaging Block
90 days
2 years
90 days
1 year
BT-H Series LCD Monitors 2 years
1 year
3 years or 17,000 hrs.
Whichever comes first
This warranty does not apply to external appearance items, such as handles, knobs,
safety windows, etc. This warranty does not apply to any part, or parts, of the
product, installed, altered, repaired or misused in any way that, in the opinion of PCI,
affects the reliability of or detracts from the performance of the product.
For products requiring routine preventive maintenance, that maintenance must be
performed in order to maintain warranty coverage.
Serial numbers that have been altered, defaced or removed void this warranty. This
warranty does not cover replacements or repairs necessitated by loss or damage
resulting from any cause beyond the control of PCI.
Marking or retained images (sometimes called “burn-in”) resulting from the display of
fixed images on video display products are not defects and are not covered under
this warranty.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR
ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, or the exclusion of implied warranties, so the
above limitations and exclusions may not be applicable.
* DLP™ Projectors
3 years or 17,000 hrs.
Whichever comes first
* LCD Projectors above
2,500 ANSI Lumens
3 years or 2,500 hrs.
Whichever comes first
3 years or 2,500 hrs.
Whichever comes first.
* LCD Projectors below
2,500 ANSI Lumens
3 years or 1,500 hrs.
Whichever comes first
3 years or 1,500 hrs.
Whichever comes first
Projector Lamps
50% of the rated lamp life or 1 year. 50% of the rated lamp life or 1 year.
Whichever comes first
Whichever comes first.
3 year
103 inch Plasma displays 3 year (burn-in not covered)
Hard Drive Disk Unit
1 year plus balance (if any) of 1 year
the original Manufacturer’s
Limited Warranty.
(Content not covered)
• Dust, smoke, rental/staging environment and twenty-four/seven operation,
dramatically decreases the interval between performances of routine preventive
maintenance required to maintain this warranty coverage.
Warranty Service
If the product needs to be shipped for service, carefully pack (preferably in the
original carton) and enclose a letter, detailing the complaint. Send prepaid and
adequately insured to the local authorized Panasonic Service Centre in your
area or to Panasonic Technical Support and Product Services Department, 5770
Ambler Drive, Mississauga, Ontario, L4W 2T3. Shipping to the latter location
requires a return authorization before shipment. No liability is assumed for loss
or damage to the product while in transit.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer’s Record
The model number and serial number of this product can be found on its back cover. You should note this serial number
in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your purchase
to aid in identification in the event of theft or loss, and for Warranty Service purposes.
Model Number
Serial Number
Panasonic Corporation 2008
©
Panasonic Professional Display Company
Unit of Panasonic Corporation of North America
Executive Office :
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000
EASTERN ZONE : One Panasonic Way 4E-7 Secaucus, NJ 07094 (201) 348-7621
Mid-Atlantic/New England : One Panasonic Way 4E-7 Secaucus, NJ 07094 (201) 348-7621
Southeast Region : 1225 Northbrook Parkway, Ste 1-160 Suwanee GA 30024 (770)338-6835
Central Region : 1707 N Randall Road E1-C-1, Elgin, IL 60123 (847)468-5200
WESTERN ZONE : 3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
Dallas Region : 6226 Abington Way, Houston, TX 77008 (713) 802-2726
No. CA/Northwest Region : 5870 Stone Ridge, #3, Pleasanton, CA (925) 416-5108
Government Marketing Department : 52 West Gude Drive, Rockville, MD 20850 (301) 738-3840
Panasonic Canada Inc.
5770 Ambler Drive
Mississauga, Ontario
L4W 2T3
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|