Operating Instructions
Progressive Wide Plasma Display
Model No.
TH-42PS10EK
TH-42PS10ES
9
PS
-42
TH
High Definition Plasma Display
Model No.
TH-42PH10EK
TH-42PH10ES
TH-50PH10EK
TH-50PH10ES
TH-58PH10EK
TH-42PS9
The illustration shown is an image.
Please read these instructions before operating your set
and retain them for future reference.
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Notice
WARNING
1) To prevent damage which may result in fire or shock hazard, do not expose this appliance to dripping
or splashing.
Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including on
shelves above, etc.)
No naked flame sources, such as lighted candles, should be placed on / above the set.
2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified
service personnel.
3) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three pin earthing-type
power plug. This plug will only fit an earthing-type power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the earthing plug.
4) To prevent electric shock, ensure the earthing pin on the AC cord power plug is securely connected.
CAUTION
This appliance is intended for use in environments which are relatively free of electromagnetic fields.
Using this appliance near sources of strong electromagnetic fields or where electrical noise may overlap with the
input signals could cause the picture and sound to wobble or cause interference such as noise to appear.
To avoid the possibility of harm to this appliance, keep it away from sources of strong electromagnetic fields.
Trademark Credits
• VGA is a trademark of International Business Machines Corporation.
• Macintosh is a registered trademark of Apple Computer, USA.
• S-VGA is a registered trademark of the video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been
fully respected.
Note:
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention
to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3
mode.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
WARNING
Setup
This Plasma Display is for use only with the following optional accessories. Use with any other type of optional
accessories may cause instability which could result in the possibility of injury.
(All of the following accessories are manufactured by Matsushita Electric Industrial Co., Ltd.)
• Speakers......................................................TY-SP42P8W-K (TH-42PS10EK, TH-42PH10EK),
TY-SP42P8W-S (TH-42PS10ES, TH-42PH10ES),
TY-SP50P8W-K (TH-50PH10EK),
TY-SP50P8W-S (TH-50PH10ES),
TY-SP58P10WK (TH-58PH10EK)
• Pedestal .......................................................TY-ST07-K (TH-42PS10EK, TH-42PH10EK, TH-50PH10EK),
TY-ST07-S (TH-42PS10ES, TH-42PH10ES, TH-50PH10ES),
TY-ST08-K (TH-42PS10EK, TH-42PH10EK, TH-50PH10EK),
TY-ST08-S (TH-42PS10ES, TH-42PH10ES, TH-50PH10ES),
TY-ST58-K (TH-58PH10EK)
• Mobile stand.................................................TY-ST42PF3 (TH-42PS10EK/S, TH-42PH10EK/S, TH-50PH10EK/S),
TY-ST58PF10
• Wall-hanging bracket (vertical).....................TY-WK42PV7
• Wall-hanging bracket (angled) .....................TY-WK42PR7
• Wall-hanging bracket (drawer type) .............TY-WK42DR1 (TH-42PS10EK/S, TH-42PH10EK/S, TH-50PH10EK/S)
• Ceiling-hanging bracket ...............................TY-CE42PS7 (TH-42PS10EK/S, TH-42PH10EK/S, TH-50PH10EK/S)
• BNC Component Video Terminal Board.......TY-42TM6A
• BNC Composite Video Terminal Board........TY-42TM6B
• BNC Dual Video Terminal Board..................TY-FB9BD
• SCART Terminal Board................................TY-FB8SC
• RCA Component Video Terminal Board.......TY-42TM6Z
• RCA Composite Video Terminal Board ........TY-42TM6V
• RGB (Digital) Terminal Board.......................TY-42TM6D
• RGB Active Through Terminal Board ...........TY-42TM6G
• PC Input Terminal Board..............................TY-42TM6P
•
Composite / Component Video Terminal Board ..TY-42TM6Y
• SDI Terminal Board......................................TY-FB7SD
• HD-SDI Terminal Board................................TY-FB9HD
• HDMI Terminal Board...................................TY-FB8HM
• Ir Through Terminal Board ...........................TY-FB9RT
• U/V Tuner Board with Hospitality Port..........TY-FB9TE (TH-50PH10EK/S, TH-58PH10EK)
• Set Up Loader..............................................TY-RM09SL (TH-50PH10EK/S, TH-58PH10EK)
• Wireless Presentation Board........................TY-FB10WPE (TH-42PH10EK/S, TH-50PH10EK/S, TH-58PH10EK)
• AV Terminal Box ...........................................TY-TB10AV
• Touch Panel .................................................TY-TP42P8-S (TH-42PS10EK/S, TH-42PH10EK/S),
TY-TP50P8-S (TH-50PH10EK/S), TY-TP50P10S (TH-50PH10EK/S),
TY-TP42P10S (TH-42PS10EK/S, TH-42PH10EK/S),
TY-TP58P10S (TH-58PH10EK)
• Anti glare filter ..............................................TY-AR50P9W (TH-50PH10EK/S),
TY-AR42P9W (TH-42PS10EK/S, TH-42PH10EK/S),
TY-AR58P10W (TH-58PH10EK)
Always be sure to ask a qualified technician to carry out set-up.
Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard
unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from
being played with by young children, creating the potential risk of suffocation.
Do not place the Plasma Display on sloped or unstable surfaces.
• The Plasma Display may fall off or tip over.
Do not place any objects on top of the Plasma Display.
• If water is spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result
in fire or electric shock. If any foreign objects get inside the Plasma Display, please consult your local Panasonic
dealer.
Transport only in upright position!
• Transporting the unit with its display panel facing upright or downward may cause damage to the internal
circuitry.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table
cloths and curtains.
For sufficient ventilation;
If using the pedestal (optional accessory) for the Plasma Display, leave a space of at least 10 cm at the top,
left and right, at least 6 cm at the bottom, and at least 7 cm at the rear. If using some other setting-up method,
leave a space of at least 10 cm at the top, bottom, left and right, and at least 7 cm at the rear.
When using the Plasma Display
The Plasma Display is designed to operate on 220 - 240 V AC, 50/60 Hz.
Do not cover the ventilation holes.
• Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display.
Do not stick any foreign objects into the Plasma Display.
• Do not insert any metal or flammable objects into the ventilations holes or drop them onto the Plasma Display, as
doing so can cause fire or electric shock.
Do not remove the cover or modify it in any way.
• High voltages which can cause severe electric shocks are present inside the Plasma Display. For any inspection,
adjustment and repair work, please contact your local Panasonic dealer.
Ensure that the mains plug is easily accessible.
An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing
connection.
Do not use any power supply cord other than that provided with this unit.
• Doing so may cause fire or electric shocks.
Securely insert the power supply plug as far as it will go.
• If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall
socket is loose, they shall not be used.
Do not handle the power supply plug with wet hands.
• Doing so may cause electric shocks.
Do not do anything that may damage the power cable. When disconnecting the power cable, pull on the plug
body, not the cable.
• Do not damage the cable, make any modifications to it, place heavy objects on top of it, heat it, place it near any
hot objects, twist it, bend it excessively or pull it. To do so may cause fire and electric shock. If the power cable is
damaged, have it repaired at your local Panasonic dealer.
If the Plasma Display is not going to be used for any prolonged length of time, unplug the power supply plug
from the wall outlet.
If problems occur during use
If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come out
from the Plasma Display, immediately unplug the power supply plug from the wall outlet.
• If you continue to use the Plasma Display in this condition, fire or electric shock could result. After checking that
the smoke has stopped, contact your local Panasonic dealer so that the necessary repairs can be made. Repairing
the Plasma Display yourself is extremely dangerous, and shall never be done.
If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet
becomes damages, disconnect the power supply plug immediately.
• A short circuit may occur, which could cause fire. Contact your local Panasonic dealer for any repairs that need to
be made.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
CAUTION
When using the Plasma Display
Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.
• Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands
or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result.
Be sure to disconnect all cables before moving the Plasma Display.
• If the Plasma Display is moved while some of the cables are still connected, the cables may become damaged,
and fire or electric shock could result.
Disconnect the power supply plug from the wall socket as a safety precaution before carrying out any
cleaning.
• Electric shocks can result if this is not done.
Clean the power cable regularly to prevent it becoming dusty.
• If dust built up on the power cord plug, the resultant humidity can damage the insulation, which could result in fire.
Pull the power cord plug out from the wall outlet and wipe the mains lead with a dry cloth.
This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment.
Install your infrared sensor in a place away from direct or reflected light from your Plasma Display.
Cleaning and maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in
which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until
the surface is dry.
• Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may
become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner,
otherwise the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been
added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
• Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get
inside the unit, operating problems may result.
• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the
cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods
in contact with articles made from rubber or PVC.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Accessories Supply
Check that you have the accessories and items shown
Operating Instruction book
Remote Control Transmitter
EUR7636090R
Batteries for the Remote
Control Transmitter
(2 × R6 (UM3) Size)
Power supply cord
Fixing bands × 2
Remote Control Batteries
Requires two R6 batteries.
2. Insert batteries - note correct
3. Replace the cover.
1. Pull and hold the hook, then open
the battery cover.
polarity ( + and -).
+
-
+
-
“R6 (UM3)” size
Helpful Hint:
For frequent remote control users, replace old batteries with Alkaline
batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.
Observe the following precaution:
1. Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5. Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
When connecting the speakers, be sure to use only the optional accessory speakers.
Refer to the speaker’s Installation Manual for details on speaker installation.
(Example: TH-42PH10EK)
Speakers (Optional accessories)
1
2
1
SPEAKERS
Terminals (L)
SPEAKERS
AC cord connection
Terminals (R)
2
(see page 12)
– AC cord fixing
Unplug the AC cord
Unplug the AC cord
pressing the two
knobs.
Plug the AC cord into the display unit.
Plug the AC cord until it clicks.
Note:
When disconnecting the AC cord, be
absolutely sure to disconnect the AC
cord plug at the socket outlet first.
Note:
Make sure that the AC cord is locked
on both the left and right sides.
– Cable fixing bands Secure any excess cables with bands as required.
Pass the attached cable To secure cables connected to Terminals, wrap the cable fixing band around them
fixing band through the clip then pass the pointed end through the locking block, as shown in the figure.
as shown in the figure.
While ensuring there is sufficient slack in cables to minimize stress (especially
in the power cord), firmly bind all cables with the supplied fixing band.
To tighten:
To loosen:
Push the catch
Pull
Pull
2
1
R
L
R
L
AUDIO
AUDIO
VIDEO
S VIDEO
AUDIO
B
AV IN
A
SLOT1
SLOT2
SLOT3
PC IN
SERIAL
Dual Video Terminals (equivalent
of BNC Dual Video Terminal Board
(TY-FB9BD)) (see page 11)
Optional Terminal
Board Insert Slot
(covered)
From EXTERNAL
monitor terminal on
Computer (see page 9) (see page 10)
From SERIAL Terminal
on Computer
Notes:
On TH-42PH10EK/S, TH-50PH10EK/S and TH-58PH10EK, Terminal board is installed in SLOT 1 at factory shipment.
•
• On TH-42PS10EK/S, SLOT 1-3 are all empty at factory shipment.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
PC Input Terminals connection
COMPUTER
AUDIO
PC IN
TH-42PS9
Conversion adapter
(if necessary)
Mini D-sub 15p
RGB
PC cable
Audio
Stereo plug
Connect a cable which matches
the audio output terminal on the computer.
Notes:
• Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input
Terminal.
• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
• The display resolution is a maximum of 640 × 480 dots (TH-42PS10EK/S), 768 × 768 dots (TH-42PH10EK/S),
1,024 × 768 dots (TH-50PH10EK/S, TH-58PH10EK) when the aspect mode is set to “4:3”, and 852 × 480 dots
(TH-42PS10EK/S), 1,024 × 768 dots (TH-42PH10EK/S), 1,366 × 768 dots (TH-50PH10EK/S, TH-58PH10EK) when
the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show
fine detail with sufficient clarity.
• The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will
need to make setting changes to the computer at the time of connection.
• Some PC models cannot be connected to the set.
• There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.
• The computer shown in the illustration is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified
frequency range.
• Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.
• Change the “Component/RGB-in select” setting in the “Setup” menu to “Component”
(when Component connection) or “RGB” (when RGB signal connection). (see page 38)
• To use sync input VBS signals, use the connector which incorporates a 75-ohm termination resistance and which is
available on the market, for the connection of the HD connector where the VBS signals are to be input.
Signal Names for Mini D-sub 15P Connector
Pin No.
1
Signal Name
R (PR/CR)
Pin No.
6
Signal Name
Pin No.
Signal Name
5
4
3
2
1
11
GND (Ground)
NC (not connected)
10
9
8
7
6
2
3
4
5
7
8
12
13
14
15
G (Y)
GND (Ground)
GND (Ground)
SDA
HD/SYNC
VD
15 14 13 12 11
B (PB/CB)
9
NC (not connected)
GND (Ground)
NC (not connected)
GND (Ground)
Pin Layout for PC Input
Terminal
10
SCL
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
SERIAL Terminals connection
The SERIAL terminal is used when the Plasma Display is controlled by a computer.
COMPUTER
1
2
3
4
5
6
7
8
9
SERIAL
RS-232C Straight cable
Pin layout for SERIAL Terminal
D-sub 9p
Notes:
• Use the RS-232C cable to connect the computer to the Plasma Display.
• The computer shown is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled
by a computer which is connected to this terminal.
The computer will require software which allows the sending and receiving of control data which satisfies the conditions
given below. Use a computer application such as programming language software. Refer to the documentation for
the computer application for details.
Communication parameters
RS-232C Conversion cable
Signal level
Synchronization method
Baud rate
RS-232C compliant
D-sub 9-pin female
Details
R X D
T X D
Asynchronous
9600 bps
None
2
3
5
Parity
Character length
Stop bit
GND
8 bits
1 bit
-
4
1
6
9
Non use
•
7
8
Shorted
NC
Flow control
•
Basic format for control data
Command
The transmission of control data from the computer
starts with a STX signal, followed by the command,
the parameters, and lastly an ETX signal in that order.
If there are no parameters, then the parameter signal
does not need to be sent.
Command
PON
POF
Parameter
Control details
None
None
**
0
1
None
SL1
SL2
Power ON
Power OFF
Volume 00 - 63
Audio MUTE OFF
Audio MUTE ON
Input select (toggle)
Slot1 input
AVL
AMT
IMS
STX
C1 C2 C3
:
P1 P2 P3 P4 P5
ETX
Colon Parameter(s) End
Slot2 input
Slot3 input
PC input
(1 - 5 bytes) (03h)
Start
(02h)
3-character
command (3 bytes)
SL3
PC1
SL1A
SL1B
SL2A
SL2B
Slot1 input (INPUT1A)
Slot1 input (INPUT1B)
Slot2 input (INPUT2A)
Slot2 input (INPUT2B)
Notes:
• If multiple commands are transmitted, be sure to wait
for the response for the first command to come from
this unit before sending the next command.
• If an incorrect command is sent by mistake, this
unit will send an “ER401” command back to the
computer.
• SL1A, SL1B, SL2A and SL2B of Command IMS are
available only when a dual input terminal board is
attached.
DAM
None
Screen mode select (toggle)
NORMAL (4 : 3)
ZOOM
NORM
ZOOM
FULL
JUST
SELF
FULL
JUST
Panasonic AUTO
With the power off, this display responds to PON command
only.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
AV connection (for TH-42PH10EK/S, TH-50PH10EK/S, TH-58PH10EK)
This unit has a terminal board equivalent to BNC Dual Video Terminal Board (TY-FB9BD) as standard equipment.
Example of input signal source
R
L
R
L
AUDIO
AUDIO
VIDEO
S VIDEO
B
AV IN
A
S VIDEO VCR
SLOT1
SLOT2
SLOT3
PC
CAMCORDER
VCR
R
L
R
L
VIDEO
OUT
S VIDEO
OUT
AUDIO
AUDIO
OUT
OUT
Note:
Additional equipment, cables and adapter plugs shown are not supplied with this set.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Power On / Off
Connecting the AC cord plug to the Plasma Display.
Fix the AC cord plug securely to the Plasma
Display with the clamper. (see page 8)
Connecting the plug to the Wall Outlet
Notes:
• Main plug types vary between countries. The power plug shown
at right may, therefore, not be the type fitted to your set.
• When disconnecting the AC cord, be absolutely sure to
disconnect the AC cord plug at the socket outlet first.
TH-42PS9
INPUT
MENU
/
V
O
L
+
/
ENTER/
Power Indicator
Press the Power switch on the Plasma Display to turn the set
on: Power-On.
Remote Control
Sensor
Power Indicator: Green
Example: The screen below is displayed for a while after the
Plasma Display is turned on (setting condition is an
example).
When the Power is turned on for the first
time, the Language selection screen is
displayed.
From the second time on, the below
screen is displayed for a while (setting
condition is an example).
OSD Language
English (UK)
Deutsch
Français
Italiano
PC
From the second time on, language
selection can be done from the setup
menu. (see page 13)
16:9
Español
ENGLISH (US)
Select the desired language using the
or
button and press the ACTION ( )
button.
Note:
Select
Set
Set with the remote control. Buttons on the
main unit are unavailable for this setting.
Press the
button on the remote control to turn the Plasma Display off.
Power Indicator: Red (standby)
Press the
button on the remote control to turn the Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the
unit, when the Plasma Display is on or in standby mode.
switch on the
Note:
During operation of the power management function, the power indicator turns
orange in the power off state.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial selections
Selecting the input signal
Select the input signals to be connected by installing the optional Terminal Boards.
Press to select the input signal to be played back from
the equipment which has been connected to the Plasma
Display.
Input signals will change as follow:
• TH-42PS10EK/S
INPUT1
INPUT2
INPUT3
PC
• TH-42PH10EK/S, TH-50PH10EK/S, TH-58PH10EK
INPUT1A INPUT1B INPUT2 INPUT3
PC
SLOT1 is for dual input so that you can select INPUT1A
or INPUT1B for INPUT1.
INPUT1A : VIDEO signal terminal in SLOT1
INPUT1B : S-VIDEO signal terminal in SLOT1
Notes:
TH-42PS9
INPUT
MENU
/
VOL
+
/
ENTER/
• Selecting is also possible by pressing the INPUT button on the unit.
• Input terminal will not be selected if the terminal board is not installed into the
SLOT.
• Select to match the signals from the source connected to the component/RGB input
terminals. (see page 38)
• In 2 screen display, the same input mode cannot be selected for the main picture
and sub picture.
INPUT
MENU
/
VOL
+
/
ENTER/
Selecting the On-Screen Menu Language
Press to display the Setup menu.
Press to select the OSD Language.
Press to select your preferred language.
Selectable languages
Setup
1/2
Signal
English(UK)
Deutsch
Component/RGB-in select
RGB
Français
Italiano
Español
ENGLISH(US)
.......(Chinese)
.......(Japanese)
Input label
Power save
Standby save
Power management
Auto power off
OSD Language
PC
Off
Off
Off
Off
(
)
English UK
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Controls
Remote control sensor
Volume Adjustment
Volume Up “+” Down “–”
When the menu screen is
displayed:
“+”: press to move the cursor
up
“–”: press to move the cursor
down
(see page 16)
INPUT
MENU
/
VOL
+/
ENTER/
Enter / Aspect button
(see page 16, 18)
MENU Screen ON / OFF
Main Power On / Off Switch
Each time the MENU button is pressed, the menu
screen will switch. (see page 16)
Power Indicator
The Power Indicator will light.
Normal Viewing
Sound
Picture
Pos. /Size
Setup
• Power-OFF ....Indicator not illuminated (The unit
will still consume some power
as long as the power cord is still
inserted into the wall outlet.)
INPUT button
(INPUT1, INPUT2, INPUT3 and PC selection)
(see page 13)
• Standby..........Red
• Power-ON......Green
• DPMS.............Orange (With PC input signal
and during operation of PC’s
screensaver.)
N button (see page 19, 22, 23, 24, 25)
POS. / SIZE button (see page 19)
PICTURE button (see page 22)
INPUT button
(INPUT1, INPUT2, INPUT3 and PC selection)
Press to select INPUT1, INPUT2, INPUT3 and PC input
SLOTS sequentially. (see page 13)
SURROUND button
The surround setting switches on and off each time
the SURROUND button is pressed.
The benefits of surround sound are enormous. You
can be completely enveloped in sound; just as if
you were at a concert hall or cinema.
Note:
Sound mute On / Off (see page 25)
Numeric buttons (see page 37)
ASPECT button
Press to adjust the aspect. (see page 18)
The surround settings are memorized separately
for each Sound Mode (Normal, Dynamic, Clear).
On
Off
MULTI Window buttons (see page 20)
Surround
On
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Controls
Standby (ON / OFF) button
The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 12).
Press ON to turn the Plasma Display On, from Standby mode. Press OFF to turn the Plasma Display Off
to Standby mode.
R button (see page 17)
Press the R button to return to previous menu screen.
POSITION buttons
Status button
ACTION button
Press the “Status” button to display the current system status.
Press to make
selections.
PC
1
2
4:3
SOUND button
(see page 25)
Off timer
90
3
1
2
3
Input label
Aspect mode (see page 18)
Off timer
The off timer indicator is displayed only when the off timer
has been set.
SET UP button (see page 16, 17)
DIRECT INPUT buttons
Press the INPUT “1”, “2”, “3” or “PC” input mode selection button to
select the input mode.
This button is used to switch directly to INPUT mode.
These buttons can only display the slot which is installed. If you
press the button whose slot is not installed, it automatically displays
the current input signal.
When a dual input terminal board is attached, A or B is displayed
depending on the selected input signal. (Ex. INPUT1A, INPUT1B)
Notes:
• For TH-42PH10EK/S, TH-50PH10EK/S and TH-58PH10EK, press
to switch the input mode between INPUT1A and INPUT1B.
•
Image retention (image lag) may occur on the plasma display panel when
a still picture is kept on the panel for an extended period. The function that
darkens the screen slightly is activated to prevent image retention (see
page 51), this function is not the perfect solution to image retention.
Channel Adjustment
This button cannot be used for this model.
Volume Adjustment
Press the Volume Up “+” or Down “–” button to increase or decrease
the sound volume level.
OFF TIMER button
The Plasma Display can be preset to switch to stand-by after a fixed
period. The setting changes to 30 minutes, 60 minutes, 90 minutes
and 0 minutes (off timer cancelled) each time the button is pressed.
30
60
0
90
When three minutes remain, “OFF TIMER 3” will flash.
The off timer is cancelled if a power interruption occurs.
Remote ID lock (see page 37)
Digital Zoom (see page 26)
Press to access
Digital Zoom.
This displays an enlargement of the designated part of the
displayed image.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Menu Displays
To Picture adjust menu
(see page 22)
The MENU button on the unit can also
be pressed.
1
Press to select.
Picture
1/2
Normal
Normalise
Picture Mode
Contrast
Brightness
Colour
Normal
INPUT
MENU
/
VOL +/
ENTER/
25
0
0
0
5
[ from the unit ]
Tint
Sharpness
Each time the MENU button is pressed,
the menu screen will switch.
Normal Viewing
Sound
Picture
Pos. /Size
Setup
INPUT
MENU
/
VOL +/
ENTER/
Picture
2/2
Normal
Off
On
White balance
Colour Management
Advanced settings
2
1
1
2
Press to select.
Press to access each adjust
screen.
Press to select
“On”.
Setup
1/2
Press to enter
Advanced settings.
Signal
Component/RGB-in select
RGB
PC
Off
Off
Off
Input label
Power save
Standby save
Power management
Auto power off
OSD Language
To Advanced settings
(see page 22, 23)
Advanced settings
Off
(
)
English UK
Normal
Normalise
0
0
0
0
0
0
Black extension
Input level
W/B High R
W/B High B
W/B Low R
W/B Low B
Gamma
2.2
Off
AGC
To Pos./Size adjust menu
(see page 19)
During “AV(S Video)”,
“Component” and “Digital” input
signal.
Setup
2/2
Screensaver
MULTI DISPLAY Setup
Set up TIMER
Pos. /Size
PRESENT TIME Setup
Normal
Normalise
H-Pos
0
0
0
0
H-Size
V-Pos
V-Size
To Sound adjust menu
(see page 25)
During “RGB / PC” input signal.
Sound
Normal
Pos. /Size
Normalise
Normal
Sound Mode
Bass
Mid
Normal
Normalise
H-Pos
H-Size
V-Pos
0
0
0
0
0
0
0
0
0
Treble
Balance
Surround
Audio Out (PIP)
V-Size
Off
Main
Clock Phase
16
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Menu Displays
Note:
Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting.
[ from the unit ]
2
Press to access
each adjust
screen.
INPUT
MENU
/
VOL +/
ENTER/
Press the R button to return to
previous menu screen.
Press to return to next menu screen.
To Signal screen for AV
To Signal screen for
To Signal screen for RGB To Signal screen for Digital
(S Video) (see page 38, 39) Component (see page 39) (see page 39, 40)
(see page 39, 40)
[
]
[
]
[
]
[
]
Signal
3D Y/C Filter (NTSC)
Colour system
Cinema reality
Panasonic Auto (4 : 3)
P-NR
AV
Signal
Component
Signal
Sync
Cinema reality
P-NR
RGB
Signal
Digital
On
Auto
Off
4 : 3
Off
Cinema reality
P-NR
Off
Off
Cinema reality
P-NR
Auto
Off
Off
Off
Off
H-Freq. 33.8
V-Freq. 60.0
kHz
Hz
H-Freq. 33.8
V-Freq. 60.0
kHz
Hz
Note : “Signal” setup menu displays different setting condition for each input signals. (see page 13)
To setup Screensaver
Press to select Start Time / Finish Time
(see page 29-31
)
(When Time Designation is selected).
Press to select Periodic Time / Operating Time
(When Interval is selected).
Screensaver
PRESENT TIME 15:00
Start
Function
Mode
White bar scroll
Time Designation
Screensaver
PRESENT TIME 15:00
6:15
12:30
High
Off
Start Time
Finish Time
Side panel
Wobbling
Peak limit
Start
Function
Mode
Start Time
Finish Time
Side panel
Wobbling
Peak limit
White bar scroll
Time Designation
Press to Setup.
Off
6:15
12:30
High
Off
Screensaver
PRESENT TIME 15:00
Start
Function
Off
White bar scroll
Interval
12:00
3:00
High
Off
Mode
Periodic Time
Operating Time
Side panel
Wobbling
Screensaver
PRESENT TIME 15:00
Press the R button to return
to “Setup” menu.
Start
Function
Mode
Periodic Time
Operating Time
Side panel
Wobbling
Peak limit
Off
White bar scroll
Interval
12:00
3:00
High
Off
To setup Multidisplay screen
(see page 33)
MULTI DISPLAY Setup
Peak limit
Off
MULTI DISPLAY Setup
Ratio
Location
Off
2 × 2
A1
To Set up Timer selection
screen (see page 27, 28)
Press to select POWER ON
Time / POWER OFF Time.
Set up TIMER
PRESENT TIME 10:00
Set up TIMER
Off
12:00
Off
POWER ON Function
POWER ON Time
POWER OFF Function
POWER OFF Time
PRESENT TIME 10:00
Press to Set up
POWER ON Time /
POWER OFF Time.
Off
0:00
Off
POWER ON Function
POWER ON Time
POWER OFF Function
POWER OFF Time
18:00
0:00
Set up TIMER
To PRESENT TIME Setup
(see page 27)
PRESENT TIME 10:00
On
12:00
On
POWER ON Function
POWER ON Time
POWER OFF Function
POWER OFF Time
PRESENT TIME Setup
Press the R button to return
to “Setup” menu.
PRESENT TIME MON 99:99
Set
DAY
PRESENT TIME
18:00
MON
99:99
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema
format picture.
Press repeatedly to move through the aspect options:
4 : 3
Panasonic Auto
Zoom
16 : 9
Just
Note:
When selecting an input slot that attaches BNC Dual Video Terminal
Board (TY-FB9BD), Panasonic Auto cannot be selected.
[from the unit]
The aspect mode changes each time the ENTER button is
pressed.
INPUT
MENU
/
VOL +/
ENTER/
[During MULTI PIP Operations]
• Picture and Picture, Picture in Picture :
4 : 3
16 : 9
• Others
:
Aspect switching is not possible.
Notes:
• For PC signal input, the mode switches between “4:3”, “Zoom” and “16:9” only.
• For a 1125 (1080) / 60i · 50i · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p signal input, the mode
is set to “16:9” mode, and switching is not possible.
• Panasonic Auto can be selected only during Video signal input.
• The aspect mode is memorized separately for each input terminal.
Mode
4 : 3
Picture
Explanation
4
4
4
4
4
4:3 will display a 4:3 picture at its standard 4:3 size.
4 : 3
3
16
16
16
16
Zoom mode magnifies the central section of the picture.
Zoom
16 : 9
Just
Zoom
16 : 9
Just
3
9
9
9
16:9 will display the picture at its maximum size but with slight
elongation.
3
3
3
Just mode will display a 4:3 picture at its maximum size but with
aspect correction applied to the center of the screen so that
elongation is only apparent at the left and right edges of the screen.
The size of the picture will depend on the original signal.
The display will automatically become enlarged (depending on the
picture source), allowing you to view the picture at its maximum
size.
Panasonic Auto
9
Notes:
• Panasonic Auto mode is designed to automatically adjust the
aspect ratio to handle a mix of 16:9 and 4:3 program material.
Certain 4:3 program material, such as stock market data screens,
may occasionally cause the image size to change unexpectedly.
When viewing such programs, it is recommended that theASPECT
be set to 4:3.
• If adjusting the Picture V-Pos/V-Size in Panasonic Auto with 16:9
mode, the adjustment is not memorized. When exiting the mode,
the screen will return to a former adjustment.
For an elongated image Image is expanded
Panasonic
Auto
4
Changes in
accordance with
the Panasonic Auto
mode setting (see
page 39).
3
For a 4:3 image
• Panasonic Auto can not be selected while BNC Dual Video
Terminal Board (TY-FB9BD) is installed.
Note:
Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a permanent image retention
to remain on the Plasma Display Panel.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Pos. / Size
1
2
Press to display the Pos. /Size menu.
Press to select H-Pos / H-Size / V-Pos / V-Size /
Clock Phase.
Press to adjust Pos. / Size.
3
During “AV(S Video)”, “Component”
and “Digital” input signal.
Pos. /Size
4
Press to exit from adjust mode.
Normal
Normalise
H-Pos
H-Size
V-Pos
0
0
0
0
Notes:
V-Size
• Adjustment details are memorized separately for different input signal formats
(Adjustments for component signals are memorized for 525 (480) / 60i · 60p,
625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i · 24p · 25p · 30p · 24sF, 1250
(1080) / 50i, 750 (720) / 60p · 50p each, and RGB/PC/Digital signals are
memorized for each frequency.)
• If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture
position will shift up or down. This picture position movement cannot be
controlled by the Picture Pos./Size function.
During “RGB / PC” input signal.
Pos. /Size
Normal
Normalise
H-Pos
H-Size
V-Pos
0
0
0
0
0
• If adjusting the Picture V-Pos/V-Size in Panasonic Auto with 16:9 mode, the
adjustment is not memorized. When exiting the mode, the screen will return
to a former adjustment.
V-Size
Clock Phase
H-Pos Adjust the horizontal position.
H-Size Adjust the horizontal size.
V-Pos Adjust the vertical position.
V-Size Adjust the vertical size.
Clock Phase
Eliminate the flickering and distortion.
(RGB/PC in mode)
Normalise
Normalisation)
Helpful Hint (
/
While the Pos. / Size display is active, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTI PIP
Press repeatedly.
Each time pressing this button main picture and sub picture will be displayed
as follows below.
[Picture and Picture]
Main picture Sub picture
[Picture out Picture]
[Picture in Picture]
Main picture Sub picture
Main picture
Sub picture
Normal
Viewing
B
A
A
A B
B
A
Press to swap main
picture and sub picture.
A
B
B
B A
[Example]
Main picture label is bright
Press to select the input mode.
Sub picture label is bright
Under main Picture and sub picture display,
select the picture which you would like to
change input modes.
PC1
PC1
VIDEO2
VIDEO2
A
A
Notes:
B
B
• The sub picture sound is heard while a sub
picture operation is underway.
Input modes switching is possible
• The sub picture operation automatically
returns to the main picture operation if
a sub picture operation has not been
performed for about 5 seconds or if any
of the remote control buttons is pressed
Main picture label is changed Sub picture label is changed
VIDEO2
VIDEO1
PC1
VIDEO2
C
A
(except
button).
B
D
Press to change input signal.
Picture is changed
Press to move the sub picture.
Each time the location of the sub picture will be moved.
Notes:
• This button is effective only in the picture in picture.
• The sub picture may be hidden by the on screen display, depending on its position.
Notes:
• If “Input lock” in Options menu is set to other than “Off”, MULTI PIP function isn’t available.
• Sound output is from the picture which is selected in Audio Out (PIP) (See page 25).
• In 2 screen display, the same input mode cannot be selected for the main picture and sub picture.
• The main picture and sub picture are processed by different circuits, resulting in a slight difference in the clarity of
the pictures. There may also be a difference in the picture quality of the sub picture depending on the type of signals
displayed on the main picture and depending on the 2-picture display mode.
• Due to the small dimensions of the sub pictures, these sub pictures cannot be shown in detail.
•
Computer screen picture is displayed in a simplified format, and it may not be possible to discern details on them satisfactorily.
• Following combinations of two analog signals cannot be displayed simultaneously;
Component - Component, Component - PC (RGB), PC (RGB) - Component, PC (RGB) - PC (RGB)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced PIP
1
2
Press to display the Setup menu.
Press to select “OSD Language”.
3
4
Press and hold until the Options menu is displayed.
Press to select Advanced PIP.
TH-42PH10EK/S, TH-50PH10EK/S,
TH-58PH10EK
TH-42PS10EK/S
Options
1/3
Options
1/3
Weekly Command Timer
Off-timer function
Onscreen display
Initial INPUT
Initial VOL level
Maximum VOL level
INPUT lock
Studio W/B
Advanced PIP
Display size
Enable
On
On
Off
Onscreen display
Initial INPUT
Press to adjust the
menu.
Off : Sets normal two
screen display
mode (see page
20).
Off
5
6
Off
Off
0
0
Initial VOL level
Maximum VOL level
INPUT lock
Button lock
Remocon User level
Off
Off
0
0
Off
Off
Off
Off
Off
Off
Off
Off
Advanced PIP
On : Sets Advanced
PIP mode.
One screen Advanced PIP
Press to exit from
Options menu.
Sub screen 1 Main screen
2
5
3
(When Advanced PIP is On)
6
4
7
Press repeatedly.
Each time pressing this button main picture and sub picture
will be displayed as above.
Note:
To use
,
,
,
buttons for the screen operations, follow the procedures in the previous page.
Notes:
• Advanced PIP corresponding signal
Sub screen
Main screen
NTSC, PAL, SECAM (tuner, video)
640x480@60Hz, 852x480@60Hz, 1024x768@60Hz,
525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1366x768@60Hz (RGB, DVI, HDMI)
1250/50i (Component Video, RGB, DVI, SDI, HDMI) 1280x768@60Hz (DVI)
• If “Input lock” in Options menu is set to other than “Off”, MULTI PIP function isn’t available.
• Sound output is from the picture which is selected in Audio Out (PIP) (See page 25).
• In 2 screen display, the same input mode cannot be selected for the main picture and sub picture.
• The main picture and sub picture are processed by different circuits, resulting in a slight difference in the clarity of
the pictures. There may also be a difference in the picture quality of the sub picture depending on the type of signals
displayed on the main picture and depending on the 2-picture display mode.
• Due to the small dimensions of the sub pictures, these sub pictures cannot be shown in detail.
•
Computer screen picture is displayed in a simplified format, and it may not be possible to discern details on them satisfactorily.
• Following combinations of two analog signals cannot be displayed simultaneously;
Component - Component, Component - PC (RGB), PC (RGB) - Component, PC (RGB) - PC (RGB)
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustments
1
2
Press to display the Picture menu.
Select to adjust each item.
Press to select the menu to adjust.
Select the desired level by looking at
the picture behind the menu.
Note:
Menu that cannot be adjusted is grayout. Adjustable menu
changes depending on signal, input and menu setting.
Picture
1/2
Press “ ” or “ ” button to switch between modes.
Normal
Normal
Normalise
Picture Mode
Contrast
Brightness
Colour
Tint
Sharpness
Normal
25
0
0
0
5
Cinema
Dynamic
Normal
For viewing in standard (evening lighting) environments.
This menu selects the normal levels of Brightness
and Contrast.
Picture
2/2
Dynamic
For viewing in brighter environments.
This menu selects higher than normal levels of
Brightness and Contrast.
Normal
Off
On
White balance
Colour Management
Advanced settings
Cinema
Ideal for movies.
Press to select “On”.
Note:
Press to enter
If you would like to change the picture and colour of the
selected Picture menu to something else, adjust using the
items in the Picture menu. (see next page)
Advanced settings.
Advanced settings On
Enables fine picture adjustment at a
professional level.
Press “ ” or “ ” button to switch between modes.
Normal
Cool
Warm
For TH-42PS10EK/S : see page 23
For TH-42PH10EK/S,
TH-50PH10EK/S,
TH-58PH10EK : see page 24
Colour Management On
Enables vivid colour adjustment automatically.
Advanced settings Off
Displays images with settings of the
Picture menu.
Normalise
Normalisation)
Helpful Hint (
/
While the “Picture” menu is displayed, if either the N button on the remote control is pressed at any time or the
ACTION ( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustments
Notes:
Item
Effect
Adjustments
• “Colour” and “Tint” settings cannot be
adjusted for “RGB/PC” and “Digital”
input signal.
Selects the proper brightness and
density for the room.
Contrast
Less
More
• You can change the level of each
function (Contrast, Brightness, Colour,
Tint, Sharpness) for each Picture
Mode.
Adjusts for easier viewing of dark
pictures such as night scenes and
black hair.
Brightness
Darker
Brighter
Colour
Tint
Adjusts colour saturation.
Adjusts for nice skin colour.
Adjusts picture sharpness.
• The setting details for normal,
dynamic and cinema respectively
are memorized separately for each
input terminal.
• The “Tint” setting can be adjusted
for NTSC signal only during “AV
(S Video)” input signal.
Less
Reddish
Less
More
Greenish
More
Sharpness
• In Contrast, there is not a noticeable
change even when contrast is
increased with a bright picture or
reduced with a dark picture.
Advanced settings
(For TH-42PS10EK/S)
Advanced settings
Item
Effect
Details
Normal
Normalise
Black
extension
0
0
0
0
0
0
Black extension
Input level
W/B High R
W/B High B
W/B Low R
W/B Low B
Gamma
Adjusts the dark shades of the image in gradation.
Less
More
More
More
More
More
More
Up
Adjustment of parts which are extremely bright and hard to see.
(This cannot be adjusted when the input signal is Digital.)
Input level
Less
Less
Less
Less
Less
Down
Off
2.2
Off
W/B High
R
AGC
Adjusts the white balance for light red areas.
Adjusts the white balance for light blue areas.
Adjusts the white balance for dark red areas.
Adjusts the white balance for dark blue areas.
W/B High
B
W/B Low
R
W/B Low
B
Gamma
AGC
S Curve
2.0
2.2
2.5
Increases the brightness of dark signal automatically.
On
Notes:
• Carry out “W/B” adjustment as follows.
1. Adjust the white balance of the bright sections using the “W/B High R” and “W/B High B” settings.
2. Adjust the white balance of the dark sections using the “W/B Low R” and “W/B Low B” settings.
3. Repeat steps 1 and 2 to adjust.
Steps 1 and 2 affect each other’s settings, so repeat each step in turn to make the adjustment.
• The adjustment values are memorized separately for each input terminal.
• The adjustment range values should be used as an adjustment reference.
Normalise
Normalisation)
Helpful Hint (
/
On the remote control unit, while the “Advanced settings” menu is displayed, if either the N button is pressed at any time or
the ACTION ( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustments
(For TH-42PH10EK/S, TH-50PH10EK/S, TH-58PH10EK)
2/2
Advanced settings
1/2
Advanced settings
0
0
0
0
0
0
W/B High R
W/B High G
W/B High B
W/B Low R
W/B Low G
W/B Low B
Normal
Normalise
Black extension
Input level
Gamma
0
0
2.2
Off
AGC
Item
Effect
Details
Black
extension
Adjusts the dark shades of the image in gradation.
Less
Less
Down
Off
More
More
Up
Adjustment of parts which are extremely bright and hard to see.
(This cannot be adjusted when the input signal is Digital.)
Input level
Gamma
AGC
S Curve
2.0
2.2
2.5
Increases the brightness of dark signal automatically.
Adjusts the white balance for light red areas.
Adjusts the white balance for light green areas.
Adjusts the white balance for light blue areas.
Adjusts the white balance for dark red areas.
Adjusts the white balance for dark green areas.
Adjusts the white balance for dark blue areas.
On
W/B High
R
Less
Less
Less
Less
Less
Less
More
More
More
More
More
More
W/B High
G
W/B High
B
W/B Low R
W/B Low G
W/B Low B
Notes:
• Carry out “W/B” adjustment as follows.
1. Adjust the white balance of the bright sections using the “W/B High R”, “W/B High G” and “W/B High B” settings.
2. Adjust the white balance of the dark sections using the “W/B Low R”, “W/B Low G” and “W/B Low B” settings.
3. Repeat steps 1 and 2 to adjust.
Steps 1 and 2 affect each other’s settings, so repeat each step in turn to make the adjustment.
• The adjustment values are memorized separately for each input terminal.
• The adjustment range values should be used as an adjustment reference.
Normalise
Normalisation)
Helpful Hint (
/
On the remote control unit, while the “Advanced settings” menu is displayed, if either the N button is pressed at any time or
the ACTION ( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Adjustment
1
2
Press to display the Sound menu.
Select to adjust each item.
Press to select the menu to adjust.
Select the desired level by listening to the sound.
Bass
Sound
Emits the original sound.
Normal
Adjusts low pitch sounds
Normal
Normalise
Sound Mode
Bass
Mid
Treble
Balance
Surround
Audio Out (PIP)
Mid
Normal
Dynamic
Clear
0
0
0
0
Accentuates sharp
sound.
Adjusts normal sounds
Treble
Adjusts high pitch sounds
Attenuates human voice.
Off
Main
Balance
Adjusts left and right volumes
Surround
Select On or Off
Selects main
picture sound.
(When main picture
sound is chosen.)
Main
INPUT1
PC
Sub
Selects PIP frame
sound.
(When PIP frame
sound is chosen.)
INPUT1
PC
Musical note is displayed on right side of the audio output screen label.
Notes:
• Press the SURROUND button to directly turn the surround effect On and Off. (see page 14)
• Bass, Mid, Treble and Surround settings are memorized separately for each Sound Mode.
Normalise
Normalisation)
Helpful Hint (
/
While the “Sound” menu is displayed, if either the N button on the remote control is pressed at any time or the
ACTION ( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
Mute
Useful when answering the phone or receiving unexpected visitors.
Press to mute the sound.
Press again to reactivate sound. Sound is also reactivated when power is turned off
or volume level is changed.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Zoom
This displays an enlargement of the designated part of the displayed image.
Display the operation guide.
1
Exit
Press to access Digital Zoom.
The operation guide will be displayed.
1
During Digital Zoom, only the following buttons can be operated.
[Remote control]
[Unit]
POSITION /
ACTION button
INPUT
MENU
/
VOL +/
ENTER/
VOL button
VOL button
MUTE button
SURROUND button
OFF TIMER button
Select the area of the image to be enlarged.
2
Press on the enlargement location to select.
The cursor will move.
Exit
2
Select the magnification required for the enlarged display.
3
4
Each time this is pressed, the magnification factor changes.
This is shown in the image being displayed.
× 1
× 2
× 3
× 4
Return to normal display (quit Digital Zoom).
Press to exit from the Digital Zoom.
Notes:
• When power goes OFF (including “Off Timer” operation), Digital Zoom terminates.
• The Digital Zoom function cannot be selected while in the following operation state:
“Multi-viewer” (Picture in Picture, Picture out Picture, Picture and Picture) operation. (see page 20)
• While Digital Zoom is in operation, “Adjusting Pos. / Size” cannot be used.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESENT TIME Setup / Set up TIMER
The timer can switch the Plasma Display On or Off.
Before attempting Timer Set, confirm the PRESENT TIME and adjust if necessary.
Then set POWER ON Time / POWER OFF Time.
1
Press to display the Setup menu.
Press to select Set up TIMER or PRESENT TIME Setup.
2
Setup
1/2
Signal
Component/RGB-in select
RGB
PC
Off
Off
Off
Input label
Power save
Standby save
Power management
Press to display the Set up TIMER screen or
PRESENT TIME Setup screen.
Auto power off
OSD Language
Off
(
)
English UK
Setup
2/2
Screensaver
MULTI DISPLAY Setup
Set up TIMER
PRESENT TIME Setup
PRESENT TIME Setup
(For TH-42PS10EK/S)
Display the PRESENT TIME Setup screen.
To setup PRESENT TIME, follow the procedure described below.
Press to select PRESENT TIME.
1
PRESENT TIME Setup
PRESENT TIME 99:99
Set
Press to setup PRESENT TIME.
button: Forward
99:99
PRESENT TIME
button: Back
Notes:
• Pressing “ ” or “ ” button once changes PRESENT TIME 1minute.
• Pressing “ ” or “ ” button continuously changes PRESENT TIME by 15 minutes.
Press to select Set.
PRESENT TIME Setup
2
3
PRESENT TIME 99:99
Set
PRESENT TIME
10:00
Press to store PRESENT TIME Setup.
Note:
Set cannot be selected unless PRESENT TIME is set.
Press to exit from PRESENT TIME Setup.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESENT TIME Setup / Set up TIMER
(For TH-42PH10EK/S, TH-50PH10EK/S, TH-58PH10EK)
Display the PRESENT TIME Setup screen.
To setup DAY and PRESENT TIME, follow the procedure described below.
Press to select DAY or PRESENT TIME.
PRESENT TIME Setup
PRESENT TIME MON 99:99
1
Press to setup DAY or PRESENT TIME.
button: Forward
Set
MON
99:99
DAY
PRESENT TIME
button: Back
Notes:
• Pressing “ ” or “ ” button once changes PRESENT TIME 1minute.
• Pressing “ ” or “ ” button continuously changes PRESENT TIME by 15 minutes.
Press to select Set.
2
3
PRESENT TIME Setup
PRESENT TIME MON 99:99
Set
DAY
PRESENT TIME
TUE
10:00
Press to store PRESENT TIME Setup.
Notes:
• Set cannot be selected unless PRESENT TIME is set.
• Unless setting the present time other than “99:99”, DAY setting is invalid.
Press to exit from PRESENT TIME Setup.
Set up TIMER
Display the Set up TIMER screen.
Press to select
POWER ON Time / POWER OFF Time.
Press to setup
POWER ON Time / POWER OFF Time.
button: Forward
Set up TIMER
1
2
PRESENT TIME 10:00
Off
12:00
Off
POWER ON Function
POWER ON Time
POWER OFF Function
POWER OFF Time
18:00
button: Back
Notes:
• Pressing “ ” or “ ” button once changes POWER ON Time / POWER OFF Time
1minute.
• Pressing “ ” or “ ” button continuously changes POWER ON Time / POWER OFF
Time by 15 minutes.
Press to select POWER ON Function/POWER
OFF Function.
Press to select On.
Set up TIMER
PRESENT TIME 10:00
On
12:00
On
POWER ON Function
POWER ON Time
POWER OFF Function
POWER OFF Time
18:00
3
Press twice to exit from Setup.
Note:
Timer function will not work unless “PRESENT TIME” is set.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Screensaver (For preventing image retention)
Do not display a still picture, especially in 4:3 mode, for any length of time.
If the display must remain on, a Screensaver should be used.
1
Press to display the Setup menu.
Setup
2/2
Press to select Screensaver.
Screensaver
MULTI DISPLAY Setup
Set up TIMER
2
3
PRESENT TIME Setup
Press to display Screensaver screen.
Reversal / Scroll selection
Screensaver
PRESENT TIME 99:99
Start
Function
Mode
Press to select Function.
White bar scroll
Off
6:15
12:30
High
Off
Start Time
Finish Time
Side panel
Wobbling
Peak limit
Press to select the desired function.
White bar scroll
Image Reversal
Off
White bar scroll : The white bar will scroll from left to right.
Image Reversal : Negative image will be displayed on the screen.
Mode selection
4
5
Screensaver
PRESENT TIME 99:99
Start
Function
Mode
Press to select Mode.
White bar scroll
Off
6:15
12:30
High
Off
Start Time
Finish Time
Side panel
Wobbling
Press to select each mode items.
Off
Peak limit
Off
Interval
: Operates when Periodic Time and Operating Time are setup
and those times arrive.
Time Designation : Operates when Start Time and Finish Time are setup and
those times arrive.
On
: Operates when Start is selected and the ACTION ( ) button
is pressed.
Start setting
Screensaver
PRESENT TIME 99:99
When the Mode is set to On, press to select
Start.
Start
Function
Mode
White bar scroll
On
6:15
12:30
High
Off
Start Time
Finish Time
Side panel
Wobbling
Peak limit
Off
Press to start Screensaver.
The menu screen will disappear and the Screensaver will be activated. To stop the
Screensaver under On, press the R button.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Screensaver (For preventing image retention)
Setup of Screensaver Time
After selecting Time Designation or Interval, the relevant Time Setup will become available for selection and the
Operating Time may be set. (Time cannot be set when “Mode” is “On” or “Off”.)
Screensaver
Screensaver
Screensaver
PRESENT TIME 15:10
PRESENT TIME 15:00
PRESENT TIME 99:99
Start
Function
Mode
Start Time
Finish Time
Side panel
Wobbling
Peak limit
Start
Function
Mode
Periodic Time
Operating Time
Side panel
Wobbling
Start
Function
Mode
Start Time
Finish Time
Side panel
Wobbling
Peak limit
White bar scroll
Time Designation
White bar scroll
White bar scroll
Interval
12:00
3:00
High
Off
Off
6:15
12:30
High
Off
6:15
12:30
High
Off
Peak limit
Off
Off
Off
Press to select Start Time / Finish Time
(When Time Designation is selected).
Press to select Periodic Time / Operating Time
(When Interval is selected).
Screensaver
PRESENT TIME 15:10
Start
Function
Mode
Start Time
Finish Time
Side panel
Wobbling
Peak limit
Press to setup.
button: Forward
button: Back
White bar scroll
Time Designation
6:15
12:30
High
Off
Notes:
• Pressing “ ” or “ ” button once changes the Time 1 minute.
[However, switching occurs every 15 minutes when Periodic Time is selected.]
• Pressing “ ” or “ ” button continuously changes the Time by 15 minutes.
Off
Screensaver
Screensaver
Screensaver
PRESENT TIME 15:10
PRESENT TIME 15:00
PRESENT TIME 15:00
Start
Function
Mode
Start Time
Finish Time
Side panel
Wobbling
Peak limit
Start
Function
Mode
Periodic Time
Operating Time
Side panel
Wobbling
Start
Function
Mode
Periodic Time
Operating Time
Side panel
Wobbling
White bar scroll
Time Designation
White bar scroll
White bar scroll
Interval
0:00
0:00
High
Off
Interval
12:00
3:00
High
Off
0:00
0:00
High
Off
Peak limit
Off
Off
Peak limit
Off
Note: Timer function will not work unless “PRESENT TIME” is set.
Reduces screen image retention
These functions prevent the occurrence of an “image retention” on the display when turned ON.
Wobbling: Automatically shifts the display image (therefore unnoticeable to the eye) to prevent image retention of
sharper contour of image.
On1: Shifts the image every 30 seconds.
On2: Shifts the image at a dot level pitch depending on screen-detection.
Peak limit: Suppresses image contrast (peak brightness).
Note: When a still picture is viewed for an extended time, the screen may become slightly darker. (see page 51)
1
2
Press to display the Setup menu.
Setup
Screensaver
MULTI DISPLAY Setup
Set up TIMER
2/2
Press to select “Screensaver”.
PRESENT TIME Setup
Screensaver
Press to display Screensaver menu.
PRESENT TIME 99:99
Start
Function
Mode
Press to select “Wobbling” or “Peak limit”.
3
White bar scroll
Off
Press to select “On1”, “On2” or “Off” (Wobbling).
“On” or “Off” (Peak limit).
6:15
12:30
High
Off
Start Time
Finish Time
Side panel
Wobbling
Peak limit
Off
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Screensaver (For preventing image retention)
Side Panel Adjustment
side panel
Do not display a picture in 4:3 mode for an extended period,
as this can cause an image retention to remain on the side
panels either side of the display field.
To reduce the risk of such an image retention, illuminate the
side panels.
4:3
Screen Display
image retention
This function may be applicable to the non-picture area.
Non picture area
Picture out Picture
Picture and Picture
Display the Screensaver screen.
(Refer to the previous page, operation guide steps 1 and 2)
1
Press to select Side panel.
Screensaver
PRESENT TIME 99:99
Start
Function
Mode
Press to select Off, Low, Mid, High.
White bar scroll
Off
Off
Low
Mid
High
6:15
12:30
High
Off
Start Time
Finish Time
Side panel
Wobbling
Peak limit
Off
2
Press to exit from Screensaver.
Notes:
• To reduce the occurrence of image retention, set the Side panel to High.
• The side panels may flash (alternate black / white) depending on the picture being shown on the screen. Using
Cinema mode will reduce such flashing.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Reduces power consumption
• Power save:
• Standby save:
When this function is turned On, luminous level of the Plasma Display is suppressed, so
power consumption is reduced.
When this function is turned On, power consumption of the microcomputer is reduced
during power supply standby (see page 12, 14-15), so standby power of the set is reduced.
• Power management: The unit power supply is turned On or Off depending on whether or not there is a signal
during PC input mode.
This function is enabled when it is turned On. (Only during input from PC (Mini D-sub) terminal)
• Auto power off:
Equipment power supply is turned Off when there is no signal.
When this is set to On, the power supply of the unit goes Off 10 minutes after the input
signals stop.
This function is effective for input signals except input from PC (Mini D-sub) terminal.
Press to select
“Power save”
“Standby save”
“Power management”
“Auto power off”.
1
Setup
1/2
Signal
Component/RGB-in select
RGB
PC
Off
Input label
Power save
Standby save
Power management
Auto power off
OSD Language
Off
Off
Off
Press to select “On” or “Off”.
2
3
(
)
English UK
On
Off
Note:
“Power management” and “Auto power off” are effective
during normal viewing (one picture screen) only.
Press to exit from Setup.
Customizing the Input labels
This function can change the label of the Input signal to be displayed.
Select the input signal which you would like to change its label before customizing
the Input labels. (see page 13,15)
Setup
1/2
Signal
Component/RGB-in select
Press to select Input label.
RGB
PC
Off
On
Off
Off
(
Input label
Power save
Standby save
Power management
Auto power off
OSD Language
Press to change the Input label.
)
English UK
Note:
While selecting an Input signal through Optional Terminal Board connected to Slot1, Slot2 and Slot3, the Input label
will depend on each Optional Terminal Board.
Input labels for Slot1, Slot2, Slot3 and Mini D-sub:
[Slot1 Input] INPUT1 / VIDEO1 / COMPONENT1 / RGB1 / DIGITAL1 / PC1 / DVD1 / CATV1 / VCR1 / STB1
[Slot2 Input] INPUT2 / VIDEO2 / COMPONENT2 / RGB2 / DIGITAL2 / PC2 / DVD2 / CATV2 / VCR2 / STB2
[Slot3 Input] INPUT3 / VIDEO3 / COMPONENT3 / RGB3 / PC3 / DVD3 / CATV3 / VCR3 / STB3
[PC (Mini D-sub) input] PC / COMPONENT / RGB / DVD / STB
When BNC Dual Video Terminal Board (TY-FB9BD) is used, an “A” or “B” is added at the end of each input label,
depending on the input selected (see below).
Addition sign
Selected Input
“A”
Composite
“B”
S VIDEO
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for MULTI DISPLAY
(For TH-42PS10EK/S)
By lining up Plasma Displays in groups of 4, 9 or 16 as illustrated below, an enlarged picture may be displayed across
all screens.
For this mode of operation, each plasma display has to be set up with a Display number to determine its location.
group of 4 (2 × 2 (F))
group of 9 (3 × 3 (F))
group of 16 (4 × 4 (F))
Two options are selectable for MULTI DISPLAY (see next page).
How to Setup MULTI DISPLAY
1
Press to display the Setup menu.
Press to select the MULTI DISPLAY Setup.
Setup
2/2
2
Screensaver
MULTI DISPLAY Setup
Set up TIMER
PRESENT TIME Setup
Press to display the “MULTI DISPLAY Setup”
menu.
Press to select the MULTI DISPLAY Setup.
MULTI DISPLAY Setup
3
MULTI DISPLAY Setup
Ratio
Location
Off
2 × 2
A1
Press to select “On” or “Off”.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for MULTI DISPLAY
How to set the display location number for each Plasma Display
Press to select Ratio (2nd step).
MULTI DISPLAY Setup
4
5
MULTI DISPLAY Setup
Ratio
Location
Off
2 × 2
A1
Press to select “2 × 2”, “2 × 2 F”, “3 × 3”,
“3 × 3F”, “4 × 4”, “4 × 4F”.
Press to select Location.
MULTI DISPLAY Setup
MULTI DISPLAY Setup
Ratio
Location
Off
2 × 2
A1
Press to select the required arrangement number.
(A1-D4 : Refer to the following)
Display Number locations for each arrangement
( 2 × 2 (F) )
( 3 × 3 (F) )
( 4 × 4 (F) )
6
Press twice to exit from Setup.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for MULTI DISPLAY
(For TH-42PH10EK/S, TH-50PH10EK/S, TH-58PH10EK)
By lining up Plasma Displays in groups, for example, as illustrated below, an enlarged picture may be displayed across all screens.
For this mode of operation, each plasma display has to be set up with a Display number to determine its location.
(Example)
group of 4 (2 × 2)
group of 9 (3 × 3)
group of 16 (4 × 4)
(see page 36 for more displays lineups.)
How to Setup MULTI DISPLAY
1
2
Press to display the Setup menu.
Press to select the MULTI DISPLAY Setup.
Setup
2/2
Screensaver
MULTI DISPLAY Setup
Set up TIMER
PRESENT TIME Setup
Press to display the “MULTI DISPLAY Setup”
menu.
Press to select the MULTI DISPLAY Setup.
Press to select “On” or “Off”.
MULTI DISPLAY Setup
3
MULTI DISPLAY Setup
Horizontal Scale
Vertical Scale
Seam hides video
Location
Off
× 2
× 2
Off
A1
On
Power On Screen Delay
How to set the display location number for each Plasma Display
Press to select Horizontal Scale.
MULTI DISPLAY Setup
4
5
Press to select “× 1”, “× 2”, “× 3”, “× 4”.
MULTI DISPLAY Setup
Horizontal Scale
Vertical Scale
Seam hides video
Location
Off
× 2
× 2
Off
A1
On
Power On Screen Delay
Press to select Vertical Scale.
MULTI DISPLAY Setup
Press to select “× 1”, “× 2”, “× 3”, “× 4”.
MULTI DISPLAY Setup
Horizontal Scale
Vertical Scale
Off
× 2
× 2
Off
A1
On
SEAM HIDES VIDEO
Location
Power On Screen Delay
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for MULTI DISPLAY
Press to select Seam hides video.
MULTI DISPLAY Setup
6
7
MULTI DISPLAY Setup
Horizontal Scale
Vertical Scale
Seam hides video
Location
Off
× 2
× 2
Off
A1
On
Press to select “Off”, “On”.
Power On Screen Delay
Press to select Location.
MULTI DISPLAY Setup
MULTI DISPLAY Setup
Horizontal Scale
Vertical Scale
Seam hides video
Location
Off
× 2
× 2
Off
A1
On
Press to select the required arrangement
number. (A1-D4 : Refer to the following)
Power On Screen Delay
Display Number locations for each arrangement.
(Examples)
( 2 × 1 )
( 2 × 3 )
( 4 × 2 )
( 4 × 4 )
Power On Screen Delay
8
Turning the power on for the multiple displays system, each display is turned on with a time lag to reduce the
power load.
MULTI DISPLAY Setup
Press to select Power On Screen Delay.
MULTI DISPLAY Setup
Horizontal Scale
Vertical Scale
Seam hides video
Location
ON
× 2
× 2
Off
A1
Press to select Off or On.
Off:All the display turns on simultaneously.
On:Each display turns on in the order of Location.
Delay time=Location (difference from A1) × 1 sec.
Example) Case of B2 in 4 × 2
Power On Screen Delay
On
A1, A2, A3, A4, B1, B2
5 sec.
Notes:
• This setting is valid when MULTI DISPLAY Setup is On.
• During this function is working, the power indicator is blinking green.
• This function also works when the power recovers from failure or after plugging off and in again the power cord.
If unplugging and plugging the power cord while the unit is in standby mode and the power is being supplied to the
board, each unit has time delay to start supplying the power to the attached board according to Location, and the
power indicator lights up red first and it turns orange when the power starts being supplied to the board.
9
Press twice to exit from Setup.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for MULTI DISPLAY
F (Seam hides video) Setting
To hide joints between displays.
To show joints between displays.
Model No.
Reference
Suitable for moving image display.
(2 × 2, 3 × 3, 4 × 4)
Suitable for still image display.
(2 × 2F, 3 × 3F, 4 × 4F)
TH-42PS10EK/S
Step 4, Page 34
Step 6, Page 36
TH-42/50PH10EK/S,
TH-58PH10EK
On
Off
ID Remote Control Function
You can set the remote control ID when you want to use this remote control on one of several different displays.
Switch
to
on the right side.
1
Press the
Press one of
Press one of
button on the remote control.
2
3
4
-
-
,
,
for the tens digit setting.
for the units digit setting.
Notes:
• The numbers in 2, 3 and 4 should be set up quickly.
• Adjustable ID number range is 0 - 99.
• If a number button is pressed more than two times, the first two numbers become the ID number for the remote
control.
ID remote control button operation
The operation is the same as normal remote control except for the
button.
ID Cancellation
Press
button on remote control. (This has the same effect as pressing the
,
,
buttons at the same time.)
Notes:
• Set the Remote ID “On” to operate the ID remote control.
If Remote ID is set to “On”, you can use the remote control without identical ID number during option menu display.
(see page 43, 46)
• The ID remote control cannot be used when ID select is set to anything other than 0, and the remote control ID is
not the same as the ID select number (see page 43, 46).
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for Input Signals
Component / RGB-in select
Select to match the signals from the source connected to the Component / RGB input terminals.
Y, PB, PR signals
“Component”
R, G, B, HD, VD signals
“RGB”
1
Press to display the Setup menu.
Press to select the “Component / RGB-in
select”.
2
Press to select the desired input signal.
Component
RGB
Setup
1/2
3
Press to exit from adjust mode.
Signal
Component/RGB-in select
RGB
PC
Off
Input label
Power save
Standby save
Power management
Auto power off
OSD Language
Off
Off
Off
Note:
Selection may not be possible, depending on which optional board is installed.
(
)
English UK
3D Y/C Filter – For NTSC AV images
Select “Signal” from the “Setup” menu duringAV(S Video) input signal. (“Signal
[AV]” menu is displayed.)
Setup
1/2
Press to select the “3D Y/C Filter (NTSC)”
1
Signal
Component/RGB-in select
RGB
PC
Off
Press to set On / Off.
Input label
Power save
Standby save
Power management
Auto power off
OSD Language
Off
Off
Off
(
)
English UK
Press ACTION ( ) button
2
Press to exit from adjust mode.
[
]
Signal
AV
3D Y/C Filter (NTSC)
On
Auto
Off
4 : 3
Off
Colour system
Cinema reality
Panasonic Auto (4 : 3)
P-NR
Note:
When On, this setting only affects NTSC input signals.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for Input Signals
Colour system / Panasonic Auto
Select Signal from the “Setup” menu during AV(S Video) input signal. (“Signal
[AV]” menu is displayed.)
Setup
1/2
Signal
Press to select the “Colour system” or
“Panasonic Auto”.
Component/RGB-in select
RGB
PC
Off
Off
Off
Input label
Power save
Press to select each functions.
Standby save
Power management
Auto power off
OSD Language
Off
(
)
English UK
Press ACTION ( ) button
If the picture image becomes unstable:
[
]
Signal
AV
With the system set on Auto, under conditions of low level or noisy input
signals the image may in rare cases become unstable. Should this occur,
set the system to match the format of the input signal.
3D Y/C Filter (NTSC)
On
Auto
Off
4 : 3
Off
Colour system
Cinema reality
Panasonic Auto (4 : 3)
P-NR
Mode
Function
Colour system
Set the colour system to match the input signal. When selecting “AUTO”, the colour system is automatically
selected from NTSC/PAL/SECAM, however, M.NTSC signal is not displayed properly depending on the
attached terminal board. To display M.NTSC signal, select “M.NTSC” in Colour system.
Auto
PAL
SECAM
M.NTSC
NTSC
Panasonic Auto Set to “4 : 3” to view 4:3 images in an unchanged format when Panasonic Auto is selected.
(4 : 3) If you would like to view 4:3 images in Just format, set to “Just”.
Note:
Panasonic Auto does not function when BNC Dual Video Terminal Board (TY-FB9BD) is used.
Cinema reality / P-NR
Cinema reality:
When on, the display attempts to reproduce a more natural interpretation of sources
such as movie pictures, which are recorded at 24 frames per second.
Setup
1/2
If the picture is not stable, turn the setting to off.
Note:
When On, this setting only affects the following signal input:
• NTSC / PAL signal input during “AV(S Video)” input signal.
• 525i(480i) 625i(575i), 1125(1080) / 60i signal input during “Component” input
signal.
Signal
Component/RGB-in select
RGB
PC
Off
Off
Off
Input label
Power save
Standby save
Power management
Auto power off
OSD Language
Off
(
)
English UK
P-NR:
Automatically reduces unwanted picture noise.
Note:
Press ACTION ( ) button
P-NR cannot be adjusted while a PC signal is being applied.
[
]
[
]
Signal
AV
Signal
RGB
Press to select Cinema
reality or P-NR.
Press to set On / Off.
3D Y/C Filter (NTSC)
Colour system
Cinema reality
Panasonic Auto (4 : 3)
P-NR
On
Auto
Off
4 : 3
Off
Sync
Cinema reality
P-NR
Auto
Off
Off
1
H-Freq. 33.8
V-Freq. 60.0
kHz
Hz
[
]
[
]
Signal
Component
Signal
Digital
Cinema reality
P-NR
Off
Off
Cinema reality
P-NR
Off
Off
H-Freq. 33.8
V-Freq. 60.0
kHz
Hz
2
Press to exit from adjust mode.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup for Input Signals
Sync
Select Signal from the “Setup” menu during RGB input signal.
Setup
1/2
Signal
Press to adjust.
1
Component/RGB-in select
RGB
PC
Off
Off
Off
Input label
Power save
Standby save
Power management
Auto power off
OSD Language
Off
(
)
English UK
Press ACTION ( ) button
2
[
]
RGB
Signal
Press to exit from adjust mode.
Sync
Cinema reality
P-NR
Auto
Off
Off
Setting RGB sync signal:
H-Freq. 33.8
V-Freq. 60.0
kHz
Hz
Confirm that the input is set to RGB input (this setting is valid only for RGB input
signal).
Sync
Auto
on G
VBS
Auto: The H and V sync or synchronized signal are automatically selected.
If both input, it is selected the H and V sync.
on G: Uses a synchronized signal on the Video G signal, which is input
from the G connector.
VBS: Uses a synchronized signal of Composite Sync input, which is input
from the HD connector.
Sync
Sync
Refresh Rate (for TH-42PH10EK/S, TH-50PH10EK/S, TH-58PH10EK)
This function sets the refresh rate of the display.
This menu is displayed when the input signal is 50 Hz system (50i, 50p, 25p, 24p, 24sF) of vertical scan rate.
100 Hz: Reduce screen flicker.
50 Hz: Enhance the resolution of moving images.
Note:
It is recommended to set to 100 Hz normally.
[
]
[
]
RGB
Signal
AV
Signal
Sync
Cinema reality
P-NR
Press to select Refresh Rate.
Press to adjust.
1
2
3D Y/C Filter (NTSC)
Auto
Off
Off
Auto
Off
4 : 3
Colour system
Cinema reality
Panasonic Auto (4 : 3)
P-NR
Refresh Rate
100 Hz
Off
H-Freq. 33.8
V-Freq. 60.0
kHz
Hz
Refresh Rate
100 Hz
[
]
[
]
Signal
Component
Signal
Digital
Cinema reality
P-NR
Refresh Rate
Off
Off
100 Hz
Cinema reality
P-NR
Refresh Rate
H-Freq. 33.8
V-Freq. 60.0
Off
Off
100 Hz
Press to exit from adjust
mode.
kHz
Hz
H-Freq. (kHz) / V-Freq. (Hz)
Displays the H (Horizontal) / V (Vertical) frequencies.
This display is valid only for RGB / PC and Digital input signal.
Display range:
H-Freq. 33.8
V-Freq. 60.0
kHz
Hz
Horizontal 15 - 110 kHz
Vertical 48 - 120 Hz
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
(For TH-42PS10EK/S)
1
Press to display the Setup menu.
Press to select “OSD Language”.
2
3
Press and hold until the Options menu is displayed.
Press to select your preferred menu.
4
Press to adjust the menu.
5
Options
1/3
Off-timer function
Onscreen display
Initial INPUT
Enable
On
Off
Off
Off
0
0
Initial VOL level
Maximum VOL level
INPUT lock
Studio W/B
Advanced PIP
Display size
Off
Off
Off
Off
6
Press to exit from
Options menu.
Item
Effect
Adjustments
Enable: Enables the “Off-timer function”.
Disable: Disables the “Off-timer function”.
Off-timer
function
Enable Disable
Note:
When “Disable” is set, the Off-timer is cancelled.
On: Displays all the following on screen.
• Power on display
• Input signal switch display
• No signal display
Onscreen
display
On
Off
• Mute and the remaining time of off-timer after was pressed.
Off: Hides all the items above from view.
Off
PC
INPUT1
INPUT2
INPUT3
Adjusts the input signal when the unit is turned on.
Notes:
• Only the adjusted signal is displayed. (see page 13).
• Signal can be displayed when the Terminal board is installed.
• This menu is available only when “INPUT lock” is “Off”.
Initial INPUT
• When a dual input terminal board is attached, A or B is displayed depending on the selected
input signal. (Ex. INPUT1A, INPUT1B)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
Options
1/3
Off-timer function
Onscreen display
Initial INPUT
Enable
On
Off
Off
Off
0
0
Initial VOL level
Maximum VOL level
INPUT lock
Studio W/B
Advanced PIP
Display size
Off
Off
Off
Off
Item
Effect
Adjustments
Press
button to adjust the volume when the unit is turned on.
Off
On
Off: Sets normal volume.
On: Sets your preferred volume.
Notes:
Initial VOL
level
Off
On
•
•
When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.
You can hear the changed volume regardless of your volume setting before opening the options menu if
you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Press
button to adjust the maximum volume.
Off
On
Off: Sets auto maximum volume.
On: Sets your preferred maximum volume.
Notes:
Maximum VOL
level
Off
On
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level”
automatically becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
•
You can hear the changed volume regardless of your volume setting before opening the options menu if
you adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
Off
PC
INPUT1
INPUT2
INPUT3
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 13).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
INPUT lock
• In two screen display mode, if anything other than “Off” is set, the value will be fixed as the value
input in the single screen display mode.
• When a dual input terminal board is attached, A or B is displayed depending on the selected
input signal. (Ex. INPUT1A, INPUT1B)
Off: Nullify all the settings adjusted.
On: Sets the colour temperature for TV studio.
Note: Valid only when the low is set as colour temperature on screen adjustment.
Off: Sets normal two screen display mode (see page 20).
On: Sets Advanced PIP mode (see page 21).
Notes:
Studio W/B
Off
Off
On
On
Advanced PIP
• When “INPUT lock” is “On”, you cannot use all the two screen display functions.
•
,
buttons are unavailable during Advanced PIP mode operation.
Adjusts the image display size on screen.
Off: Sets the normal image display size on screen.
On: Sets the image display size approximately 95 % of the normal image display.
Off
On
Display size
Notes:
Off
On
• This setting is valid only when the input signals are as follows; 525i, 525p, 625i, 625p, 750/60p,
750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p, 1250/50i (Component
Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when two screen display, digital zoom or Multi screen is selected.
• When “Display size” is set to “On”, Pos. /Size adjustment cannot be used.
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
Options
2/3
Button lock
Remocon User level
ID select
Off
Off
0
Remote ID
Serial ID
Off
Off
Item
Effect
Adjustments
Off
MENU&ENTER
On
Off: All the buttons at the bottom of the main unit can be used.
MENU & ENTER:
Button lock
Locks
and
buttons on bottom face of main unit.
ENTER/
MENU
On: Locks all the button on bottom face of main unit.
Off User1 User2 User3
Off: You can use all of the buttons on the remote control.
User1:You can only use
,
,
,
,
,
,
,
buttons on the remote
Remocon
User level
control.
User2:You can only use
,
buttons on the remote control.
User3:Locks all the buttons on remote control.
Sets panel ID number when panel is used in “Remote ID” or “Serial ID”.
Set value range: 0 - 100
(Standard value: 0)
ID select
Off: Disables ID remote control functions. You can use normal remote control operations.
On: Enable ID remote control functions.
Remote ID
Serial ID
Off
On
On
Sets the panel ID Control.
Off: Disables external control by the ID.
On: Enables the external control by the ID.
Off
Options
3/3
Slot power
Off
Off
Off
V. lnstallation
Rotate
Serial Slot Select
Slot1
Item
Effect
Adjustments
Off
Off: Power is not transmitted to the slot power.
Auto: Power is transmitted to the slot power only when main power is on.
On: Power is transmitted to the slot power when main power is on or in the standby state.
Note: In some cases, power is transmitted to the slot power when main power is on or in the
standby state regardless of the slot power setting.
Auto
On
Slot Power
Off: Sets fan to the horizontal installation mode.
On: Sets fan to the vertical installation mode.
Notes:
• This functions when display is turned on.
• Vertical installation is available without this mode setting.
• Turn up the power switch for the upward direction when you set Display vertically.
V.Installation
Rotate
Off
Off
On
On
Off: Does not rotate the image.
On: Rotates the image 180 degrees.
Slot1
Slot2
Slot3
Serial Slot
Select
Selects the slot which communicates serial.
Note: The setting of an external command can be set only from the fixed serial terminal (see page
10).
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote
ID” adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the
button on main unit together with
button on the remote control and hold for more than 5 seconds.
The “SHIPPING” menu is displayed and the lock is released when it disappears.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
(For TH-42PH10EK/S, TH-50PH10EK/S, TH-58PH10EK)
1
Press to display the Setup menu.
Press to select “OSD Language”.
2
3
Press and hold until the Options menu is displayed.
Press to select your preferred menu.
4
Press to adjust the menu.
5
Options
Weekly Command Timer
Onscreen display
Initial INPUT
1/3
On
Off
Off
Off
0
0
Initial VOL level
Maximum VOL level
INPUT lock
Button lock
Remocon User level
Advanced PIP
Off
Off
Off
Off
6
Press to exit from
Options menu.
Item
Effect
Adjustments
Weekly
Command
Timer
Sets Weekly Command Timer. (see page 48)
On: Displays all the following on screen.
• Power on display
• Input signal switch display
Onscreen
display
• No signal display
On
Off
• Mute and the remaining time of off-timer after was pressed.
Off: Hides all the items above from view.
Off
PC
INPUT1
INPUT2
INPUT3
Adjusts the input signal when the unit is turned on.
Notes:
• Only the adjusted signal is displayed. (see page 13).
• Signal can be displayed when the Terminal board is installed.
• This menu is available only when “INPUT lock” is “Off”.
Initial INPUT
• When a dual input terminal board is attached, A or B is displayed depending on the selected
input signal. (Ex. INPUT1A, INPUT1B)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
Options
1/3
Weekly Command Timer
Onscreen display
Initial INPUT
On
Off
Off
Off
0
0
Initial VOL level
Maximum VOL level
INPUT lock
Button lock
Remocon User level
Advanced PIP
Off
Off
Off
Off
Item
Effect
Adjustments
button to adjust the volume when the unit is turned on.
On
Press
Off
Off: Sets normal volume.
On: Sets your preferred volume.
Notes:
Initial VOL
level
Off
On
•
•
When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.
You can hear the changed volume regardless of your volume setting before opening the options menu if you
adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Press
button to adjust the maximum volume.
Off
On
Off: Sets auto maximum volume.
On: Sets your preferred maximum volume.
Notes:
Maximum VOL
level
Off
On
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level”
automatically becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
•
You can hear the changed volume regardless of your volume setting before opening the options menu if you
adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
Off
PC
INPUT1
INPUT2
INPUT3
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 13).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
INPUT lock
• In two screen display mode, if anything other than “Off” is set, the value will be fixed as the value
input in the single screen display mode.
• When a dual input terminal board is attached, A or B is displayed depending on the selected input
signal. (Ex. INPUT1A, INPUT1B)
Off
MENU&ENTER
On
Off: All the buttons at the bottom of the main unit can be used.
MENU & ENTER:
Locks
and
buttons on bottom face of main unit.
ENTER/
MENU
On: Locks all the button on bottom face of main unit.
Sets Button lock with the unit buttons in the following procedure.
Button lock
Off: Press four times→Press
four times→Press four times→Press
INPUT
ENTER/
MENU & ENTER: Press
four times→Press four times→Press
four times→Press
INPUT
ENTER/
ENTER/
On: Press four times→Press
four times→Press four times→Press
ENTER/
ENTER/
Off
User1
User2
User3
Off: You can use all of the buttons on the remote control.
User1:You can only use
,
,
,
,
,
,
,
buttons on the remote
Remocon
User level
control.
User2:You can only use
,
buttons on the remote control.
User3:Locks all the buttons on remote control.
Off: Sets normal two screen display mode (see page 20).
On: Sets Advanced PIP mode (see page 21).
Notes:
Advanced PIP
Off
On
• When “INPUT lock” is “On”, you cannot use all the two screen display functions.
buttons are unavailable during Advanced PIP mode operation.
•
,
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
Options
2/3
Off-timer function
Initial Power Mode
ID select
Enable
Normal
0
Remote ID
Off
Serial ID
Off
Display size
Studio W/B
Off
Off
Studio Gain
Off
Item
Effect
Adjustments
Enable: Enables the “Off-timer function”.
Disable: Disables the “Off-timer function”.
Off-timer
function
Enable Disable
Note:
When “Disable” is set, the Off-timer is cancelled.
Normal
Standby On
Sets the power mode of the unit for when the power recovers from failure or after plugging off
and in again.
Normal: Power returns in as the same state as before the power interruption.
Standby: Power returns in standby mode. (Power Indicator : red/orange)
Initial Power
Mode
On:
Power returns in power On. (Power Indicator : green)
When using multiple displays, “Standby” is preferred to be set in order to reduce a
power load.
Note:
Sets panel ID number when panel is used in “Remote ID” or “Serial ID”.
Set value range: 0 - 100
ID select
(Standard value: 0)
Off: Disables ID remote control functions. You can use normal remote control operations.
On: Enable ID remote control functions.
Remote ID
Serial ID
Off
Off
On
On
Sets the panel ID Control.
Off: Disables external control by the ID.
On: Enables the external control by the ID.
Adjusts the image display size on screen.
Off: Sets the normal image display size on screen.
On: Sets the image display size approximately 95 % of the normal image display.
Off
On
Notes:
Display size
Off
On
• This setting is valid only when the input signals are as follows;
NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (BNC Dual Video Terminal Board (TY-FB9BD))
525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p,
1125/30p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when two screen display, digital zoom or Multi screen is selected.
• When “Display size” is set to “On”, Pos. /Size adjustment cannot be used.
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.
Off: Nullify all the settings adjusted.
On: Sets the colour temperature for TV studio.
Note: Valid only when the low is set as colour temperature on screen adjustment.
Studio W/B
Studio Gain
Off
Off
On
On
Sharpens the contrast for a better view when a part of the image is too light to see.
Off: Disables “Studio Gain”.
On: Enables “Studio Gain”.
Note: This setting is valid only when the input signals are as follows:
Component Video, RGB (analog), SDI, HDMI
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
Options
3/3
Slot power
Off
Off
Off
V. lnstallation
Rotate
Serial Slot Select
Slot1
Item
Effect
Adjustments
Off
Off: Power is not transmitted to the slot power.
Auto: Power is transmitted to the slot power only when main power is on.
On: Power is transmitted to the slot power when main power is on or in the standby state.
Note: In some cases, power is transmitted to the slot power when main power is on or in the
standby state regardless of the slot power setting.
Auto
On
Slot Power
Off: Sets fan to the horizontal installation mode.
On: Sets fan to the vertical installation mode.
Notes:
• This functions when display is turned on.
• Turn up the power switch for the upward direction when you set Display vertically.
V.Installation
Rotate
Off
On
On
Off: Does not rotate the image.
On: Rotates the image 180 degrees.
Off
Slot1
Slot2
Slot3
Serial Slot
Select
Selects the slot which communicates serial.
Note: The setting of an external command can be set only from the fixed serial terminal (see page 10).
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote
ID” adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the
button on main unit together with
button on the remote control and hold for more than 5 seconds.
The “SHIPPING” menu is displayed and the lock is released when it disappears.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
Weekly Command Timer (for TH-42PH10EK/S, TH-50PH10EK/S, TH-58PH10EK)
You can set 7-day timer programming by setting time and command.
Note:
Before setting Weekly Command Timer, set PRESENT TIME Setup. (see page 27)
Press to select Function.
Options
1/3
1
Press to select “On”.
Weekly Command Timer
Onscreen display
On
Note:
Press ACTION ( ) button
• When Function is set to On, Set up TIMER
(see page 28) is unavailable and Interval /
Time Designation in Mode of Screensaver
(see page 29) cannot be selected.
Weekly Command Timer
Function
Monday
On
Program1
Program3
---
Tuesday
Wednesday
Thursday
Friday
Program3
---
Program6
Program4
Saturday
Sunday
Program Edit
Press to select a day.
Weekly Command Timer
2
Press to select a program number.
On
Function
Monday
Tuesday
Wednesday
Thursday
Friday
Program1
Program3
---
Note:
• You can set the program from 1 to 7.
--- indicates unset.
Program3
---
Program6
Program4
Saturday
Sunday
Program Edit
Program number
Program3
---
Thursday
Friday
Saturday
Sunday
Press to select Program Edit.
3
4
Program6
Program4
Program Edit
Press to show the Program Edit screen.
Program Edit screen
Press to select Program.
1/8
Weekly Command Timer
Press to change the program numbers (1-7).
1
Program
8:00 PON
01
02
03
04
05
10:30 IMS:SL1
--:-- ---
--:-- ---
--:-- ---
12:00 DAM:ZOOM
9:12 AVL:10
--:-- ---
06
07
08
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Options Adjustments
Press to select a command number.
5
Press to show the previous / next command
pages (1-8) of the selected program.
Press to show the command setting screen.
1/8
8/8
Weekly Command Timer
Program
Weekly Command Timer
Program
1
1
AVL:00
8:00 PON
57
58
59
60
61
20:00
01
02
03
04
05
06
07
08
DAM:NORM
10:30 IMS:SL1
--:-- ---
20:30
22:00 POF
--:-- ---
--:-- ---
--:-- ---
--:-- ---
--:-- ---
--:-- ---
--:-- ---
62
63
64
12:00 DAM:ZOOM
9:12 AVL:10
--:-- ---
Command (--- indicates unset)
Set time of timer(--:-- indicates unset)
Command numbers
Press to select Command No.
Command setting screen
6
7
Weekly Command Timer
Program
Press to select a command number.
1
Command No
02
10:30
Time
Command
IMS:SL1
Weekly Command Timer
Press to select Time / Command.
Press to set each item.
Time: Set the time to execute a command
program.
1
Program
02
10:30
IMS:SL1
Command No
Time
Command
Pressing “ ” or “ ” button once changes “Time” 1 minute.
Pressing “ ” or “ ” button continuously changes “Time” by 15 minutes.
Command:Select a command to execute at the set time. This unit has 64 commands
to set. (see page 53)
Notes:
•
Command is performed in order of execution time, regardless of the command number.
• If a command execution time overlaps with that of other commands, these commands
are performed in number order.
• Pressing , Time becomes --:-- and Command becomes ---.
Note:
• Press
to return to the previous screen.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Shipping condition
This function allows you to reset the unit to the factory setting.
1
Press to display the Setup menu.
Press to select “OSD Language”.
2
Press and hold till the SHIPPING menu is
displayed.
Setup
1/2
3
4
Signal
Component/RGB-in select
RGB
Input label
Power save
Standby save
Power management
Auto power off
OSD Language
PC
Off
Off
Off
Off
Press to select “YES”.
(
)
English UK
YES
SHIPPING
Press to confirm.
[from the unit]
1 Press the MENU button till the Setup menu is displayed.
2 Press the Volume Up“+” or Down“–” button to select “OSD Language”.
3 Press and hold the ENTER button till the SHIPPING menu is displayed.
4 Press the Volume Up“+” or Down“–” button to select “YES”.
5 Press the ENTER button and wait for 10 sec.
Note:
Press the R button to return to Setup menu when SHIPPING menu is displayed.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Checks
Picture
Sound
Electrical Appliances
Interference
Noisy Sound
Cars / Motorcycles
Fluorescent light
Volume
Normal Picture
No Picture
No Sound
No Sound
(Check whether the mute function has been activated on the remote control.)
Not plugged into AC outlet
Not switched on
Picture and Brightness/Volume setting
(Check by pressing the power switch or stand-by button on the remote control.)
If a signal with a non-applicable colour system format, or frequency is input, only
No Picture
No Colour
Normal Sound the input terminal indication is displayed.
Colour controls set at minimum level
Normal Sound (see page 22, 23)
Colour system (see page 39)
No remote control operations can be performed.
Check whether the batteries have discharged completely and, if they have not,
whether they were inserted properly.
Check whether the remote control sensor is exposed to an outdoor light or a
strong fluorescent light.
Check whether the remote control designed specifically for use with the unit is
being used. (The unit cannot be operated by any other remote control.)
If there is nothing wrong with the picture or sound, this is the sound of the cabinet
undergoing very slight contractions in response to changes in the room temperature.
There are no adverse effects on the performance or other aspects.
A cracking sound is sometimes heard from the unit.
The top or bottom of the picture on the screen is cut Adjust the position of the picture on the screen.
off when I use the zoom function.
Areas at the top and bottom of the screen where When using a video software program (such as a cinema size program) with a
the image is missing appear when I use the zoom screen wider than one in the 16:9 mode, blank areas separate from the images
function.
are formed at the top and bottom of the screen.
I can hear sounds coming from inside the unit.
When the power is turned on, a sound of the display panel being driven may be
heard: This is normal and not indicative of malfunctioning.
This Plasma Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the
type of input signal. However, this is not a malfunction.
Plasma Display panel
Symptoms
Check
The screen darkens slightly The screen will darken slightly when photos, still images of a computer or other pictures with minimal
whenbrightpictureswithminimal movements are shown for an extended period. This is done to reduce image retention on the screen
movements are shown.
and the shortening of the screen’s service life: It is normal and not indicative of malfunctioning.
It takes a while for the picture The unit digitally processes the various signals in order to reproduce esthetically pleasing images. As
to appear.
such, it sometimes takes a few moments for the picture to appear when the power has been turned
on, when the input has been switched or when the images for the main picture and sub picture on
the two screens are swapped.
The edges of the images Due to the characteristics of the system used to drive the panel, the edges may appear to flicker in
flicker. the fast-moving parts of the images: This is normal and not indicative of malfunctioning.
The brightness on both sides of When viewing the side panels at the “High” or “Mid” setting, the brightness on both sides may change
images in the 4:3 mode changes. depending on the kind of program shown: This is normal and not indicative of malfunctioning.
Some parts of the screen do The plasma display panel is manufactured using an extremely high level of precision technology,
not light up.
however, sometimes some parts of the screen may be missing picture elements or have luminous
spots. This is not a malfunction.
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent
image retention to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed
in 4:3 mode.
Note:
The permanent image retention on the Plasma Display resulting from fixed image use is not an operating
defect and as such is not covered by the Warranty.
Image retention appears
This product is not designed to display fixed images for extended periods of time.
The display unit is fitted with a cooling fan to dissipate heat generated during normal use. The whirring
sound is caused by rotation of the fan and is not a malfunction.
[for TH-42PH10EK/S,
TH-50PH10EK/S,
TH-58PH10EK]
Whirring sounds can be heard
from the display unit.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO/PC input signals
VIDEO input (for TH-42PH10EK/S, TH-50PH10EK/S, TH-58PH10EK)
Horizontal
frequency(kHz)
Vertical
frequency(Hz)
Signal name
1
2
3
4
5
NTSC
PAL
PAL60
15.73
15.63
15.73
15.63
15.73
59.94
50.00
59.94
50.00
SECAM
Modified NTSC
59.94
Applicable input signals for Mini D-sub 15P (Component) / Mini D-sub 15P (RGB) (
*
Mark)
Horizontal
frequency
(kHz)
Vertical
frequency
(Hz)
Dot clock
frequency
(MHz)
Mini D-sub 15P Mini D-sub 15P
Signal name
(Component)
(RGB)
1
2
3
4
5
6
7
8
525 (480) / 60i
525 (480) / 60p
625 (575) / 50i
625 (575) / 50p
750 (720) / 60p
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
27.00
33.75
28.13
27.00
31.25
31.46
31.47
37.86
37.50
43.27
31.47
35.16
37.88
48.08
46.88
53.67
48.36
56.48
60.02
68.68
67.50
60.00
85.94
63.98
79.98
91.15
75.00
81.25
37.64
48.36
35.00
49.72
68.68
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
47.92
30.00
25.00
24.00
50.00
70.07
59.94
72.81
75.00
85.01
59.94
56.25
60.32
72.19
75.00
85.06
60.00
70.07
75.03
85.00
75.00
60.00
85.00
60.02
75.03
85.02
60.00
65.00
59.94
60.00
66.67
74.54
75.06
13.5
27.0
13.5
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1
∗
*
*
*
*
*
*
*
*
*
*
*
*
*
27.0
74.25
74.25
74.25
74.25
74.25
74.25
74.25
74.25
74.25
25.17
25.18
31.5
31.5
36.0
33.54
36.0
40.0
750 (720) / 50p
1,125 (1,080) / 60i
1,125 (1,080) / 50i
1,125 (1,080) / 24sF
1,125 (1,080) / 30p
1,125 (1,080) / 25p
1,125 (1,080) / 24p
1,250 (1,080) / 50i
640 × 400 @70 Hz
640 × 480 @60 Hz
640 × 480 @72 Hz
640 × 480 @75 Hz
640 × 480 @85 Hz
852 × 480 @60 Hz
800 × 600 @56 Hz
800 × 600 @60 Hz
800 × 600 @72 Hz
800 × 600 @75 Hz
800 × 600 @85 Hz
1,024 × 768 @60 Hz
1,024 × 768 @70 Hz
1,024 × 768 @75 Hz
1,024 × 768 @85 Hz
1,152 × 864 @75 Hz
1,280 × 960 @60 Hz
1,280 × 960 @85 Hz
1,280 × 1,024 @60 Hz
1,280 × 1,024 @75 Hz
1,280 × 1,024 @85 Hz
1,600 × 1,200 @60 Hz
1,600 × 1,200 @65 Hz
1,066 × 600 @60 Hz
1,366 × 768 @60 Hz
Macintosh13” (640 × 480)
Macintosh16” (832 × 624)
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
2
2
∗
*
*
*
*
∗
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
50.0
49.5
56.25
65.0
75.0
78.75
94.5
108.0
108.0
148.5
108.0
135.0
157.5
162.0
175.5
53.0
86.71
30.24
57.28
100.0
41 Macintosh21” (1,152 × 870)
∗1: When selected the RGB format and 525p signal input to the Mini D-sub 15P terminal, it is recognized as VGA 60Hz signal.
∗2: When inputted VGA 60Hz format signal from the other than Mini D-sub 15P terminal, it is recognized as 525p signal.
Note: Signals without above specification may not be displayed properly.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Command list of Weekly Command Timer
No.
1
2
3
4
5
6
7
Command
AAC:MENCLR
AAC:MENDYN
AAC:MENSTD
AAC:SURMON
AAC:SUROFF
AMT:0
Control details
Audio Menu (Clear)
Audio Menu (Dynamic)
Audio Menu (Standard)
Surround (ON)
Surround (OFF)
Audio Mute (OFF)
Audio Mute (ON)
AMT:1
8
9
ASO:M
ASO:S
AVL:00
Audio out when PIP mode (Main Picture)
Audio out when PIP mode (Sub Picture)
Audio Volume (00)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
AVL:10
AVL:20
AVL:30
AVL:40
AVL:50
AVL:60
Audio Volume (10)
Audio Volume (20)
Audio Volume (30)
Audio Volume (40)
Audio Volume (50)
Audio Volume (60)
Aspect (16:9)
Aspect (Just)
Aspect (4:3)
Aspect (Panasonic Auto)
Aspect (Zoom)
Advanced PIP mode (OFF)
Advanced PIP mode (1) (see page 21)
Advanced PIP mode (2) (see page 21)
Advanced PIP mode (3) (see page 21)
Advanced PIP mode (4) (see page 21)
Advanced PIP mode (5) (see page 21)
Advanced PIP mode (6) (see page 21)
Advanced PIP mode (OFF) (normal two screen display mode)
Advanced PIP mode (ON)
The location of the sub picture (lower right)
The location of the sub picture (lower left)
The location of the sub picture (upper left)
The location of the sub picture (upper right)
Dual Picture mode (Picture in Picture)
Dual Picture mode (Picture out Picture)
Swap main picture and sub picture when PIP mode
Dual Picture mode (Picture and Picture)
Input select (PC1) (Main Picture when PIP mode)
Input select (SLOT1) (Main Picture when PIP mode)
Input select (SLOT1A) (Main Picture when PIP mode)
Input select (SLOT1B) (Main Picture when PIP mode)
Input select (SLOT2) (Main Picture when PIP mode)
Input select (SLOT2A) (Main Picture when PIP mode)
Input select (SLOT2B) (Main Picture when PIP mode)
Input select (SLOT3) (Main Picture when PIP mode)
Sub Picture Input Select (PC1)
DAM:FULL
DAM:JUST
DAM:NORM
DAM:SELF
DAM:ZOOM
DWA:OFF
DWA:OVL1
DWA:OVL2
DWA:OVL3
DWA:OVL4
DWA:OVL5
DWA:OVL6
DWA:OVLOF
DWA:OVLON
DWA:PIN0
DWA:PIN1
DWA:PIN2
DWA:PIN3
DWA:PIP
DWA:POP
DWA:SWP
DWA:TWN
IMS:PC1
IMS:SL1
IMS:SL1A
IMS:SL1B
IMS:SL2
IMS:SL2A
IMS:SL2B
IMS:SL3
ISS:PC1
ISS:SL1
Sub Picture Input Select (SLOT1)
Sub Picture Input Select (SLOT1A)
Sub Picture Input Select (SLOT1B)
Sub Picture Input Select (SLOT2)
Sub Picture Input Select (SLOT2A)
Sub Picture Input Select (SLOT2B)
Sub Picture Input Select (SLOT3)
Screen Saver White bar scroll (OFF)
Screen Saver White bar scroll (ON)
Power OFF
ISS:SL1A
ISS:SL1B
ISS:SL2
ISS:SL2A
ISS:SL2B
ISS:SL3
OSP:SCR0
OSP:SCR1
POF
PON
Power ON
SSC:FNC0
SSC:FNC1
SSC:MOD0
SSC:MOD3
Screen Saver function (White bar scroll)
Screen Saver function (Image Reversal)
ScreenSaver (Mode (OFF))
ScreenSaver (Mode (ON))
∗
∗
VMT:0
VMT:1
Picture Mute (OFF)
Picture Mute (ON)
Picture Mute cannot be unlocked by powering off/on with the remote control. Turn off and on again with the button
on the unit or enter the command VMT:0 to unlock Picture Mute.
∗
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
TH-42PS10EK/S
Power Source
220 - 240 V AC, 50/60 Hz
Power Consumption
Power on
280 W
Stand-by condition
Power off condition
Plasma Display panel
Save off 0.8 W, Save on 0.6 W
0.2 W
Drive method : AC type
42-inch, 16:9 aspect ratio
920 mm (W) × 518 mm (H)
× 1,056 mm (diagonal)
408,960 (852 (W) × 480 (H))
[2,556 × 480 dots]
Screen size
(No.of pixels)
Operating condition
Temperature
0 °C - 40 °C
20 % - 80 %
Humidity
Applicable signals
Scanning format
PC signals
525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 50i · 24p ·
25p · 30p · 24sF ···· SMPTE274M, 1250 (1080) / 50i
VGA
SVGA, XGA, SXGA, UXGA ···· (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
PC IN
(HIGH-DENSITY MINI D-SUB 15PIN)
Y or G with/sync 1.0 Vp-p (75 Ω)
Y or G without/sync 0.7 Vp-p (75 Ω)
B/PB/CB: 0.7 Vp-p (75 Ω)
R/PR/CR: 0.7 Vp-p (75 Ω)
HD/VD: 1.0 - 5.0 Vp-p (high impedance)
with/picture 1.0 Vp-p (high impedance)
without/picture 0.3 Vp-p (high impedance)
0.5 Vrms (high impedance)
VBS (use HD port)
AUDIO IN (M3 JACK)
SERIAL
SPEAKERS (6 Ω)
Accessories Supplied
Remote Control Transmitter
Batteries
EXTERNAL CONTROL TERMINAL (D-SUB 9PIN)
16 W [8 W + 8 W] (10 % THD)
RS-232C COMPATIBLE
EUR7636090R
2 × R6 Size
Fixing bands
TMME203 × 2
Dimensions (W × H × D)
Mass (weight)
1,020 mm × 610 mm × 89 mm
main unit only
with speakers
approx. 26.0 kg net
approx. 30.0kg
Notes:
• Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
• This equipment complies with the EMC standards listed below.
EN55022, EN55024, EN61000-3-2, EN61000-3-3.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
TH-42PH10EK/S
TH-50PH10EK/S
TH-58PH10EK
Power Source
220 - 240 V AC, 50/60 Hz
Power Consumption
Power on
365 W
485 W
630 W
Stand-by condition
Power off condition
Plasma Display panel
Save off 1.0 W, Save on 0.8 W Save off 0.8 W, Save on 0.6 W Save off 0.8 W, Save on 0.6 W
0.5 W
0.3 W
0.3 W
Drive method : AC type
42-inch, 16:9 aspect ratio
922 mm (W) × 518 mm (H)
× 1,057 mm (diagonal)
Drive method : AC type
50-inch, 16:9 aspect ratio
1,106 mm (W) × 622 mm (H)
× 1,269 mm (diagonal)
Drive method : AC type
58-inch, 16:9 aspect ratio
1,287 mm (W) × 723 mm (H)
× 1,476 mm (diagonal)
Screen size
(No.of pixels)
786,432 (1,024 (W) × 768 (H)) 1,049,088 (1,366 (W) × 768 (H)) 1,049,088 (1,366 (W) × 768 (H))
[3,072 × 768 dots]
[4,098 × 768 dots]
[4,098 × 768 dots]
Operating condition
Temperature
0 °C - 40 °C
20 % - 80 %
Humidity
Applicable signals
Colour System
Scanning format
NTSC, PAL, PAL60, SECAM, Modified NTSC
525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 50i · 24p ·
25p · 30p · 24sF ···· SMPTE274M, 1250 (1080) / 50i
VGA, SVGA, XGA
PC signals
SXGA, UXGA ···· (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
AV IN
VIDEO IN (BNC)
1.0 Vp-p (75 Ω)
S VIDEO IN (MINI DIN 4PIN)
AUDIO IN (RCA PIN JACK × 4)
(HIGH-DENSITY MINI D-SUB 15PIN)
Y: 1.0 Vp-p (75 Ω), C: 0.286 Vp-p (75 Ω)
0.5 Vrms (high impedance)
Y or G with/sync 1.0 Vp-p (75 Ω)
Y or G without/sync 0.7 Vp-p (75 Ω)
PC IN
B/PB/CB: 0.7 Vp-p (75 Ω)
R/PR/CR: 0.7 Vp-p (75 Ω)
HD/VD: 1.0 - 5.0 Vp-p (high impedance)
with/picture 1.0 Vp-p (high impedance)
without/picture 0.3 Vp-p (high impedance)
0.5 Vrms (high impedance)
VBS (use HD port)
AUDIO IN (M3 JACK)
SERIAL
SPEAKERS (6 Ω)
Accessories Supplied
Remote Control Transmitter
Batteries
EXTERNAL CONTROL TERMINAL (D-SUB 9PIN)
16 W [8 W + 8 W] (10 % THD)
RS-232C COMPATIBLE
EUR7636090R
2 × R6 Size
Fixing bands
TMME203 × 2
Dimensions (W × H × D)
Mass (weight)
1,020 mm × 610 mm × 89 mm 1,210 mm × 724 mm × 95 mm 1,399 mm × 843 mm × 99 mm
main unit only
with speakers
approx. 26.0 kg net
approx. 30.0 kg
approx. 36.0 kg net
approx. 40.0 kg
approx. 54.0 kg net
approx. 59.0 kg
Notes:
• Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
• This equipment complies with the EMC standards listed below.
EN55022, EN55024, EN61000-3-2, EN61000-3-3.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Information on Disposal for Users of Waste Electrical & Electronic Equipment
(private households)
This symbol on the products and/or accompanying documents means that used electrical
and electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated
collection points, where they will be accepted on a free of charge basis. Alternatively, in
some countries you may be able to return your products to your local retailer upon the
purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any
potential negative effects on human health and the environment which could otherwise arise
from inappropriate waste handling. Please contact your local authority for further details of your nearest
designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further
information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct
method of disposal.
Customer’s Record
The model number and serial number of this product can be found on its rear panel. You should note this serial
number in the space provided below and retain this book, plus your purchase receipt, as a permanent record
of your purchase to aid in identification in the event of theft or loss, and for Warranty Service purposes.
Model Number
Serial Number
Matsushita Electric Industrial Co., Ltd.
2007 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.
©
Printed in Czech Republic
MBS0307S1047
Download from Www.Somanuals.com. All Manuals Search And Download.
|