LCD TV
Quick Use and Hookup Guide
IMPORTANT
CONTENTS
NOTE: This owner's manual is used with several
different television models. Not all features (and
drawings) discussed in this manual will necessarily
match those found with your television set. This is
normal and does not require that you contact your
dealer or request service.
Important Notice/Warning . . . . . . . . . . . . . . . . . . . . .1
AV1 Input Connections . . . . . . . . . . . . . . . . . . . . . .3
Component Video Input Connections . . . . . . . . . . .3
High Definition Input Connections . . . . . . . . . . . . .3
PC (Monitor) Connection . . . . . . . . . . . . . . . . . . . .4
AV2 Input Connections . . . . . . . . . . . . . . . . . . . . . .4
AV3 Input Connection . . . . . . . . . . . . . . . . . . . . . . .4
Monitor Output Connections . . . . . . . . . . . . . . . . . .4
LCD Stand Assemble . . . . . . . . . . . . . . . . . . . . . . . .1
Basic TV Operation . . . . . . . . . . . . . . . . . . . . . . . . . .1
Remote Control Button Descriptions . . . . . . . . . . . .1
Hooking up the Television
Remote Battery Installation . . . . . . . . . . . . . . . . . . .2
Basic Cable/Cable Box TV Connections . . . . . . . . .2
Basic Antenna TV Connections . . . . . . . . . . . . . . . .2
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD DO NOT EXPOSE THIS UNIT TO
RAIN OR EXCESSIVE MOISTURE.
BASIC LCD TV OPERATION
First, assemble the LCD TV using the steps below:
2
2
3
Y
A
W
S
I
H
T
T
R
E
S
N
I
P
O
T
1
3
LCD TELEVISION
his LCD television has a set of controls located on the side of
Tthe cabinet for use when the remote control is not needed.
1
2
Volume and Channel buttons are located
on the side of the television cabinet.
After you have connected the power cord to the TV and
plugged the cord into a wall outlet, press the POWER button
on the front of the TV cabinet to turn the TV ON.
4
Press the VOLUME + button to increase the sound level or
the VOLUME – button to lower the sound level.
Pressing both buttons at the same time will display the
onscreen menu. After you are in the menu, use these buttons to
make adjustments or selections.
2
3
Press the PROGRAM + or – button to select TV chan-
PHILIPS
nels. Use these buttons to make adjustments or selections in the
3
onscreen menu.
REMOTE CONTROL BUTTONS
TV/DVD/AUX/ACC Select Button - Press button repeatedly to select
the required device mode to perform the activities for the selected
device.
Power Button - Press to turn the TV ON and OFF.
PIP / Record
0
Button - When in TV mode, you can call up a PIP
Status/Exit Button - Press to see the current channel number on the TV
window for the PC. Likewise, when in PC mode, you can call up a PIP
window for TV channels. When in VCR mode, press button to do
recording.
screen. Also press to clear the TV menu after control adjustments.
Sleep Button - Press to set the TV to automatically turn itself OFF at a given
amount of time.
Pixel Plus / Pause
;
Button - When in TV mode, this button has no
Active Control - Press to optimize the quality of the picture according to
function.When in VCR/VCD/DVD mode, press button to do pause the
programme you are watching. Press button again to release pause mode.
the quality of reception.
4
TV Mode / 4 button - Press to directly enter TV mode. Also, press to
HD (High Definition) Mode /
button - Press to directly enter
rewind a video tape or CD/DVD disc during playback.
Radio mode. Also, press to begin playback of a video tape or CD/DVD
disc.
Format Button - Press to toggle the different screen format options.
CC Button - Press to select Closed Captioning options within the
PC Mode / 7 button - Press to directly enter PC mode. Also, press to stop
menu.
a video tape or CD/DVD disc during playback.
FM Radio Mode / 2 button - Press to directly enter Radio mode. Also,
Menu Button - Press for the onscreen menu to appear. Pressing the menu
button after menu selections are made will exit the menu from the TV
screen.
press to begin playback of a video tape or CD/DVD disc.
Cursor Buttons (Left, Right, Up, Down) - Press these buttons to highlight,
select, and adjust items on the TV's onscreen menu.
Mute Button - Press to turn the TV sound OFF . Press again to return the
sound to its previous level.
Program List / OK Button - When in TV mode, press to display a list
of channel numbers. Each channel will appear as a selectable menu
item. When in Accessory mode, it confirms selections or adjustments in
Accessory device.
Volume (+) or (–) Buttons - Press to adjust the TV sound level.
Auto Sound Button - Press to select an AutoSound™ control. Choose from
three factory-set controls (VOICE, MUSIC, and THEATRE) and a PERSON-
AL to tailor the TV sound to enhance the particular type of program you are
watching.
Channel (+) or (–) Buttons - Press to access the next or previous chan-
nel.
Auto Picture Button - Press to select an AutoPicture™ control.
Choose from four factory-set controls (MOVIES, SPORTS, WEAK
SIGNAL, and MULTI MEDIA) and a PERSONAL control that you set
according to your own preferences through the onscreen PICTURE
menu. The four factory-set controls will tailor the TV picture so as to
enhance the particular type of program you are watching, or to improve
the picture of a program that has a weak signal.
Surf Button - Press to select previously viewed channels. You can
place up to 10 channels in memory. Then by pressing the SURF button
you can quickly view the select channels.
Number Buttons - Press the number buttons for direct access to the TV
channels. For a 2-digit channel, enter the 2nd digit before the dash disap-
pears. For a 3-digit channel, enter the first digit followed the next 2 digits.
AV+ (Source) Button - Press and hold AV+ button and loop from AV1
(CVI), AV2, Rear, HD and PC to select the appropriate channel.
Alternately, press AV+ button followed by the Number 1, 2, 3, 4 or 5.
Number 1 allows you to select AV1 (CVI), Number 2 to select AV2 chan-
nel, Number 3 to select Rear channel, Number 4 to select HD and Number
5 to select PC.
3139 125 31931
Download from Www.Somanuals.com. All Manuals Search And Download.
HOOKING UP THE TELEVISION
AV1 INPUTS
BOTTOM OF TV
he audio/video input jacks on the bottom panel of the TV are
Tfor direct picture and sound connections between the TV and
a VCR (or similar device) that has audio/video output jacks.
Connect the AV1 In(put) cable to one end of an RCA
type VIDEO (yellow) cable to the supplied Audio/Video
adapter. Connect the other end of the Adapter to the AV1 in
jack on the bottom of the TV.
1
TUNE TO AV1 CHANNEL
1
Connect the AV1 In(put) cable to one end of the RCA
type AUDIO (red and white) cables to the supplied
Audio/Video adapter.
2
AUDIO IN
VIDEO IN (YELLOW)
(RED/WHITE)
Turn the VCR or accessory device and the TV On.
3
Press the AV+ button and the number 1 button on the
remote control to select the AV1 channel for the accessory
device. AV1 will appear in the upper left corner on the TV
screen when tuned properly. You can also press and hold
the AV+ button to toggle through the various channels until
AV1 appears on the screen.
4
3
3
4
With the VCR (or accessory device) ON and a prerecorded
tape (CD, DVD, etc.) inserted, press the PLAY button to
view the tape on the television.
2
VCR (or accessory device)
(EQUIPPED WITH VIDEO AND
AUDIO OUTPUT JACKS)
5
BACK OF VCR
(or Accessory device)
COMPONENT (CVI) INPUTS
omponent Video inputs provide the highest possible color and
Cpicture resolution in the playback of digital signal source
material, such as with DVD players.
1
BOTTOM OF TV
Connect the Component (Y, Pb, Pr) Video OUT jacks
from the DVD player (or similar device) to the
COMP(onent) VIDEO Input (Y green, Pb blue, Pr red)
jacks on the bottom of the TV. When using the Component
Video Inputs, it is best not to connect a signal to the AV1 in
Video Jack.
1
2
COMPONENT
VIDEO CABLES
(Green, Blue, Red)
AUDIO CABLES
(RED/WHITE)
Connect the red and white AUDIO CABLES to the
Audio (left and right) output jacks on the rear of the acces-
sory device to the Audio Adapter supplied (L and R).
Connect the adapter into the AV1 In Input Jacks on the TV.
2
The CVI connection
will be dominate over
the AV1 in Video Input.
When a Component
Video Device is con-
nected as described, it is
best not to have a video
signal connected to the
AV1 in Video Input
jack.
Turn the TV and the DVD (or digital accessory device)
ON.
CMP VIDEO
Pr
S-VIDEO
OUT
VIDEO
OUT
AU
OUT
3
4
4
Press the AV+ button and the Number 1 button on the
remote control to select the CVI channel. CVI will appear
in the upper left corner of the TV screen.
Y
L
4
Pb
Insert a DVD disc into the DVD player and press the
PLAY ᮣ button on the DVD Player.
5
3
5
ACCESSORY DEVICE
EQUIPPED WITH COMPO-
NENT VIDEO OUTPUTS.
NOTE: When using additional accessories, only one external
source will be audible, as there is only one AV1 Input jack.
HELPFUL HINT
The description for the component video connectors may differ depending on the DVD player or accessory
digital source equipment used (for example, Y, Pb, Pr; Y, B-Y, R-Y; Y, Cr, Cb). Refer to your DVD or dig-
ital accessory owner’s manual for definitions and connection details.
BOTTOM OF TV
HD (HIGH DEFINITION) INPUTS
HD 1
f your using a High Definition receiver that can transmit high
Idefinition programming, the TV can except those signals
through the HD Inputs located on the bottom of the TV.
1
Analog Connection
2
3
Digital Connection
HDMI
For Digital Connection, connect the HDMI connector of
the HD Receiver (or similar device) to the HDMI Input
1
jacks on the bottom of the TV.
OR
COMPONENT
VIDEO CABLES
(Green, Blue,
Red)
For Analog Connection, use Component Video cables to
connect the Component (Y, Pb, Pr) Video Out jacks of
5
2
the HD Receiver (or similar device) to the VGA adapter
(supplied with the TV). Connect the other end of the
adapter to the VGA Input jacks on the bottom of the TV.
AUDIO
CABLES
AUDIO
L
Y
PB
PR
OUT TO TV
Connect the red and white audio adapter to RCA type
VCR
CONTROL
CH
CH
3
4
Audio Cables. Connect the audio adapter to the PC/HD
DIGITAL
AUDIO OUT
3
RF
Audio Input jack on the bottom of the TV.
VIDEO
in
VIDEO
in
IN FROM ANT
SATELLITE IN
PHONE JACK REMOTE
S-VIDEO
1
2
Turn the TV and the HD Receiver ON.
4
Coxial Cable Lead-in fom
Cable Outlet, Cable Converter
Box, or VHF/UHF Antenna
Rear of HD Receiver (Illustration is
for reference only. Your HD
Receiver’s jack panel may be
labeled differently.
Press the HD Mode button to set the TV into the HD
Coaxial cable Lead-in
from Satellite Dish or
Antenna
4
Mode and tune to the HD signal.
5
Note: The Audio/Video cables needed for this connection are not
supplied with your TV. Please contact your dealer or Philips at
800-531-0039 for information about purchasing the needed
cables.
HD RECEIVER
EQUIPPED WITH COMPONENT
VIDEO OUTPUTS.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HOOKING UP THE TELEVISION
PC (MONITOR) INPUTS
PC
his TV can be used as a PC Monitor. Your computer will have
Tto be equipped with a VGA type video output and VGA cable.
1
BOTTOM OF TV
2
Connect one end of the VGA Video cable to the Monitor
(video) output on the computer to the PC Input (VGA) jack
AUDIO
on the bottom of the TV. You can use the DVI cable if your
ADAPTER
computer has DVI capability.
1
Although audio connections are not required, the TV can
reproduce the computers audio out by an AUDIO
DVI CABLE
2 ADAPTER to the Audio output jack on the computer (if
3
available) while connecting the other ends of the Audio
cables to the Audio In left and right (PC/HD) Input Jacks
on the bottom of the TV.
OR
VGA/RGB
Out
DVI
Audio
Out
Turn the TV and the Computer ON.
VGA CABLE
4
3 Press the PC Mode button to set the TV into the HD
Mode and tune to the computer’s signal.
4
Note: Please contact your dealer or Philips at 800-531-0039 for
information about purchasing the needed cables.
ACCESSORY DEVICE
AV2 INPUTS
(Camera., DVD, VCR, etc.)
here are Audio/Video Input Jacks located on bottom of the TV can
Talso be used for extra accessory device connections for items such
as cameras or gaming stations.
4
Connect the VIDEO (yellow) adapter cable to the VIDEO
AV2 in jack on the left rear of the TV. Connect the other end
1 of the VIDEO (yellow) cable to an RCA type VIDEO Cable.
2
1
JACK PANEL
BOTTOM OF TV
Connect that cable to the VDEO OUT jack on the back of the
accessory device being used. Note: An S-Video cable can be
used in place of the yellow Video cable if your device is
equiped with an S-Video Output. S-Video provides better video
playback.
Connect the AUDIO (red and white) adapter cable to an
RCA type Audio Cable. Connect the other ends of the
2 AUDIO (red and white) cables to the AUDIO (left and right)
OUT jacks on the rear of the accessory device being used.
Turn the accessory device and the TV ON.
3 Press the AV+ button and the number 2 button on the
remote control to select the AV2 channel for the accessory
VIDEO CABLE
4
3
3
device. AV2 will appear in the upper left corner on the TV
screen when tuned properly. You can also press and hold
the AV+ button to toggle through the various channels until
AV2 appears on the screen.
AUDIO CABLES
(Left and Right)
With the accessory device ON, press the PLAY button to acti-
AUDIO
RIGHT LEFT
VIDEO
ACCESSORY DEVICE
JACK PANEL
S-VIDEO
vate the playback on the television.
5
AV3 (SIDE) INPUTS
JACK PANEL
SIDE OF TV
uch like the AV2 jacks, the AV3 jacks allow for extra accessory
Mdevice connections for items such as cameras or gaming stations.
The AV3 Input Jacks are located on the side of the TV.
1
Connect the VIDEO (yellow) adapter cable to the VIDEO
AV3 in jack on the left rear of the TV. Connect the other end
1 of the VIDEO (yellow) cable to an RCA type VIDEO Cable.
VIDEO CABLE
Connect that cable to the VDEO OUT jack on the back of the
accessory device being used. Note: An S-Video cable can be
used in place of the yellow Video cable if your device is equiped
with an S-Video Output. S-Video provides better video play-
back.
OR
AUDIO CABLES
S-VIDEO CABLE
Connect the AUDIO (red and white) adapter cable to an
RCA type Audio Cable. Connect the other ends of the AUDIO
2 (red and white) cables to the AUDIO (left and right) OUT
AUDIO
RIGHT LEFT
VIDEO
1
S-EO
ACCESSORY DEVICE
JACK PANEL
jacks on the rear of the accessory device being used.
Turn the accessory device and the TV ON.
4
3 Press the AV+ button and the number 3 button on the
ACCESSORY DEVICE
(Camera., DVD, VCR, etc.)
AUDIO
remote control to select the AV3 channel for the accessory
CABLES
(Left and
Right)
4
device. AV3 will appear in the upper left corner on the TV
screen when tuned properly. You can also press and hold the
AV+ button to toggle through the various channels until
AV3 appears on the screen.
2
AN S-VIDEO CABLE CAN
BE USED IN PLACE OF THE
YELLOW VIDEO CABLE IF
DESIRED.
3
3
With the accessory device ON, press the PLAY button to acti-
vate the playback on the television.
5
Audio System Connection:
MONITOR OUTPUTS
AUDIO CABLES
(Red & White)
he Monitor (Audio/Video) out jacks are great for recording with a
TVCR or used to connect an external audio system for better audio.
R
L
For Audio System Connection:
AUX/TV INPUT
PHONO INPUT
Connect one end of the R(ight) and L(eft) AUDIO (Monitor
Out) jacks located on the right rear of the TV to the R and L
1
audio input jacks on your sound system. Refer to the AUDIO
1
OUT control within the Directions for Use for FIXED or VARI-
ABLE settings.
AV OUT
AUDIO L(eft) and R(ight)
2
Turn the TV and audio system ON. TV sound can be heard
AUDIO SYSTEM
with AUDIO INPUTS
through the audio system
2
For Second VCR Connection/Recorder:
The following steps allow you to connect a VCR to record the pro-
gram while your watching it.
Connect one end of the yellow Video Cable to the Monitor
out VIDEO OUT plug on the left rear of the TV. Connect the
3
other end to the VIDEO IN plug on the second VCR.
Connect one end of the red and white Audio cable from the
Monitor out L and R plugs on the left rear of the TV to the
4
AUDIO IN plugs on the VCR.
Turn the VCR ON, insert a black VHS tape and it’s ready to
record what’s being viewed on the TV screen.
5
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|