Philips Flat Panel Television 15PF5120 28B User Manual

Quick Use and Hookup Guide  
CONTENTS  
INSTALLING LCD TV ON THE WALL . .1 TUNER MODE CONTROL . . . . . . . . . . . . . 5  
UNFOLD THE BASE. . . . . . . . . . . . . . . 1 AUTO PROGRAM (SETTING UP  
TV CHANNEL INSTALLATION . . . . . . . .2 CHANNELS) . . . . . . . . . . . . . . . . . . . . 5  
PRESENTATION OF THE LCD TV . . . . . 2 CABLE BOX (WITH RF IN/OUTPUTS) . . 6  
ACCESSORIES. . . . . . . . . . . . . . . . . . . .3 CABLE BOX (WITH AUDIO/VIDEO  
BATTERY INSTALLATION . . . . . . . . . . . . 3 OUTPUTS) . . . . . . . . . . . . . . . . . . . . . 6  
REMOTE CONTROL OPERATION . . . . . .3 S-VIDEO CONNECTIONS . . . . . . . . . . . 7  
ANTENNA TV . . . . . . . . . . . . . . . . . . 4 COMPONENT (HD) CONNECTIONS . . .7  
BASIC CABLE TV CONNECTION . . . . . 4 PC (MONITOR) INPUTS . . . . . . . . . . . 8  
IMPORTANT  
NOTE: This quick setup guide is used with several  
different LCD TV models. Not all features (and drawings)  
discussed in this manual will necessarily match those  
found with your LCD TV set. This is normal and does not  
require that you contact your dealer or request service.  
WARNING:TO PREVENT FIRE OR SHOCK HAZARD  
DO NOT EXPOSETHIS UNITTO RAIN OR EXCESSIVE.  
INSTALLING LCDTV ON THE WALL  
The stand of your LCD TV complies with the VESA standard, if you intend to install the LCD TV on the wall,  
please consult a professional technician for proper installing.  
Wall Mounting of your LCD TV :  
Put your LCD TV set on a safe and flat surface, then  
fold the base backward.  
Note: To fold the base requires a degree of force.  
1
Use for the TV set a Vesa compliant wall mount (not included).  
(For 15 inch: 75x75 mm , For 20 inch: 100x100 mm)  
2
3
Use for installation by a professional technician.  
Note: The manufacture accepts no liability, ensure installation is  
done by a professional technician.  
UNFOLD THE BASE  
Expanding the base requires a degree of force; please use sufficient force to unfold the base.  
When unfolding the base, place the TV on a flat, sturdy surface before expanding the base.  
Download from Www.Somanuals.com1. All Manuals Search And Download.  
3138 155 24011  
ACCESSORIES  
BATTERY INSTALLATION  
When you unpack this unit, make sure it includes the  
following:  
Remove the battery compartment lid on  
the bottom of the remote control.  
1
2
Place lithium cell in the remote control.  
Be sure the (+) and (-) ends of the  
batteries line up as marked inside the  
battery (CR2025) compartment.  
Reattach the battery  
compartment lid.  
Power adapter & cable  
User's Manual & Quick Use and Hookup Guide  
3
1
3
d
r
a
C
y
t
n
a
r
r
r
a
a
W
W
2
Tuner L-Adapter  
Warranty Card  
REMOTE CONTROL OPERATION  
Status/Exit Button-  
Power button  
Press to turn the LCD TV on or off.  
Press to see the current channel number on the  
TV screen. Also press to clear the TV menu  
after control adjustments.  
CC button  
Press the CC button to select CC on or CC off.  
SAP button  
Press to select a sound mode if available with  
the TV programming:Mono, Stereo, or SAP.  
Sleep button  
Press to set the LCD TV to turn itself off within a  
certain time.  
Incredible Surround button-  
Adds greater depth and dimension to TV  
sound.  
PIP button  
Press repeatedly to change the size of PIP window  
in PC mode.  
Select from Incredible Surround or OFF.  
Picture Format button  
A/CH Button  
Press to go to previously selected channel.  
Press the FORMAT button repeatedly to toggle  
among the three screen format sizes; 4:3,  
EXPAND 4:3, COMPRESS 16:9,  
Menu button  
Press to activate onscreen menu, back to  
previous level inside the onscreen menu or press to  
exit the onscreen menu.  
Cursor Buttons (Left, Right, Up,  
Down)-  
Press these buttons to highlight, select, and  
adjust items on the TV’s on screen menu.  
Channel button  
Press to adjust the channel up or down.  
Volume button  
Press to increase or decrease the sound level.  
Mute button  
Press to eliminate or restore the LCD TV sound.  
Mute will appear on the screen when the sound is  
muted.  
Number buttons  
Press the number buttons for direct access to  
the TV channels. For a 3-digit channel, enter  
the first digit followed the next 2 digits.  
Auto Sound button  
Press repeatedly to select among the 4 settings;  
Personal, Voice, Music, or Theatre.  
AV+ button  
Press to select the video input source: PC,  
DVI, TV, AV, S-Video, HD.  
Auto Picture button  
Press repeatedly to select either Personal, Rich,  
Natural, Soft, or Multimedia picture setting.  
Surf Button  
Press to select previously viewed channels. You can  
place up to 8 channels in memory. Then by  
pressing the SURF button you can quickly view the  
select channels.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
ANTENNA TV  
A combination antenna receives normal broadcast channels (VHF 2–13 and UHF 14–69). Your connection is easy because there is only  
one 75 Ω (ohm) antenna jack on the side of your TV, and that’s where the antenna goes.  
If your antenna has a round cable (75 ohm) on the end, then  
you’re ready to connect it to the LCD TV. If your antenna  
has flat, twin-lead wire (300 ohm), you first need to attach  
the antenna wires to the screws on a 300- to 75-ohm  
1
TV  
adapter(not supplied).  
Connect the antenna (or adapter) to one end of the  
supplied L-Adapter as shown, and connect the other end of  
the L-Adapter to the TV jack on the side of the LCD TV.  
2
Plug the DC adapter into the DC IN 16V jack on the LCD  
TV. Plug the power cable into an outlet and switch TV set on.  
3
4
DVI-I IN  
AUDIO IN  
DC IN  
16V  
DVI (HDCP / PC ANALOG)  
Run the AUTO PROGRAM function to set up the TV for the  
broadcast or cable channels available in your area. If you do  
not run the auto program function to set up the channels ,  
your television may not operate properly.  
3
Outdoor or Indoor Antenna  
(Combination VHF/UHF)  
Television  
DC Adapter  
2
Twin-lead  
wire to  
300-75  
adapter  
Power  
Cable  
1
HELPFUL HINT  
• Remember, an antenna or cable TV signal must first be connected to  
your LCD TV.  
OR  
Antenna  
with 75  
cable  
• Please make sure that you have selected the TV mode with AV+ key  
on your remote control, before installing TV channels.  
BASIC CABLE TV CONNECTION  
Your Cable TV input into your home may be a single (75 ohm) cable or use a cable box decoder. In either case the connection is very  
simple. Follow the steps below to connect your cable signal to your new television.  
Direct cable connections:  
The Cable TV signal from  
Cable Company  
(75 coaxial cable)  
Connect the Cable TV signal to one end of the supplied  
L-Adapter as shown, and connect the other end of the  
adapter to the TV jack on the LCD TV.  
L Adapter  
1
TV  
Plug the DC adapter into the DC IN 16V jack on the LCD  
TV. Plug the power cable into an outlet and switch TV set on.  
2
3
1
Run the AUTO PROGRAM function to set up the TV for the  
broadcast or cable channels available in your area. If you do  
not run the auto program function to set up the channels ,  
your television may not operate properly.  
DVI-I IN  
AUDIO IN  
DC IN  
16V  
DVI (HDCP / PC ANALOG)  
HELPFUL HINT  
• Remember, an antenna or cable TV signal must first be connected to  
your LCD TV.  
2
Power Cable  
• Please make sure that you have selected the TV mode with AV+ key  
on your remote control, before installing TV channels.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
TUNER MODE CONTROL  
The Tuner Mode allows you to change the LCD TV’s signal input to Cable or Air  
(antenna). It’s important for the LCD TV to know if you want to receive channels from a cable TV signal or an antenna signal.  
Press the MENU button to see the onscreen menu.  
MAIN CONTROLS  
1
PICTURE  
AUDIO  
LANGUAGE  
TUNER MODE  
INSTALL  
FEATURES  
AUTO PROGRAM  
CHANNEL EDIT  
MANUAL FINE TUNE  
FACTORY RESET  
ANTENNA  
CABLE  
AUTO  
LANGUAGE  
TUNER MODE  
AUTO PROGRAM  
CHANNEL EDIT  
MANUAL FINE TUNE  
FACTORY RESET  
Press the CURSOR DOWN button to highlight the INSTALL menu.  
Press the CURSOR RIGHT button to enter the INSTALL menu.  
INSTALL  
2
3
4
5
1
6
Press the CURSOR DOWN button to highlight the TUNER MODE menu,  
then press CURSOR RIGHT to confirm.  
4
5
Press the CURSOR DOWN button to select CABLE, ANTENNA  
or AUTO, then press CURSOR RIGHT to confirm.  
Press the MENU button repeatedly to clear the menu from the screen.  
6
HELPFUL HINT  
• When CABLE is selected, channels 2-125 are available.  
• When ANTENNA is selected, channels 2-69 are available.  
• When AUTO is selected, your LCD TV will search automatically for antenna  
or cable channels.  
• Immediately after unpacking and plugging in your new television, run the AUTO  
PROGRAM function to set up the TV for the broadcast or cable channels  
available in your area. If you do not run the auto program function to set up the  
channels, your television may not operate properly.  
AUTO PROGRAM (SETTING UP CHANNELS)  
Your LCD TV can automatically set itself for local area (or cable TV) channels. This makes it easy for you to select only the TV stations in  
your area by pressing the CH+ or CH- button.  
Press the MENU button on the remote control to show the  
1
2
3
4
5
6
MAIN CONTROLS  
onscreen menu.  
PICTURE  
AUDIO  
LANGUAGE  
TUNER MODE  
FEATURES  
Press the CURSOR DOWN button to  
highlight the INSTALL menu.  
AUTO PROGRAM  
CHANNEL EDIT  
MANUAL FINE TUNE  
FACTORY RESET  
INSTALL  
Press the CURSOR RIGHT button  
to enter the INSTALL menu.  
INSTALL  
ANTENNA  
CABLE  
AUTO  
LANGUAGE  
TUNER MODE  
AUTO PROGRAM  
CHANNEL EDIT  
MANUAL FINE TUNE  
FACTORY RESET  
Press the CURSOR DOWN button to  
highlight the AUTO PROGRAM control.  
Press the CURSOR RIGHT button to start the AUTO PROGRAM scanning  
of channels.  
INSTALL  
LANGUAGE  
TUNER MODE  
Press the MENU button repeatedly to clear the menu from the screen, after  
AUTO STORE has finished.  
AUTO PROGRAM  
CHANNEL EDIT  
MANUAL FINE TUNE  
FACTORY RESET  
START?  
HELPFUL HINT  
AUTO STORE  
Immediately after unpacking and plugging in your new television, run the auto  
program function to set up the TV for the broadcast or cable channels available in  
your area. If you do not run the auto program function to set up the channels ,  
your television may not operate properly.  
PLEASE WAIT  
PROG.FOUND  
CHANNEL  
0
3
After you’ve run Auto Program, check out the results. Press the CURSOR DOWN  
or the CURSOR UP button and see which channels you can select.  
Remember, an antenna or cable TV signal must first be connected to your LCD TV.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
CABLE BOX (WITH RF IN / OUTPUTS):  
Connect the Cable TV signal to the IN jack (or RF IN or CABLE  
IN) on the Cable Box.  
1
2
3
3
L-Adapter  
TV  
Connect an RF coaxial cable (not supplied) to the OUT jack (or  
TO TV or RF OUT) of the Cable Box.  
Connect the other end of the coaxial cable to one end of the  
supplied L-Adapter as shown, and connect the other end of the  
adapter to the TV jack on the LCD TV.  
75  
Coaxial  
Cable  
Plug the DC adapter into the DC IN 16V jack on the LCD TV.  
Plug the power cable into an outlet and switch TV set on.  
DVI-I IN  
AUDIO IN  
DC IN  
16V  
4
5
DVI (HDCP / PC ANALOG)  
Set the Channel 3/4 (or Output channel) switch of the Cable Box  
to 3 or 4. Set the TV to the same channel. When watching TV  
programming, change channels at the Cable Box, not the LCD TV.  
4
The Cable TV signal from  
the Cable Company  
DC Adapter  
5
2
1
OUTPUT  
CH  
HELPFUL HINT  
Power  
Cable  
3
4
CABLE  
IN  
TO TV  
• Immediately after unpacking and plugging in your new television,  
run the auto program function to set up the TV for the broadcast  
or cable channels available in your area. If you do not run the auto  
program function to set up the channels , your television may not  
operate properly.  
• Please make sure that you have selected the TV mode with AV+ key  
on your remote control, before installing TV channels.  
CABLE BOX (WITH AUDIO /VIDEO OUTPUTS):  
This connection will supply stereo sound to the LCD TV.  
Connect the Cable TV signal to the IN jack (or RF IN or CABLE  
IN) on the Cable Box.  
TV  
1
2
Using an RCA-type video cable (not supplied) connect one end of  
the video cable to the Video Out jack of the Cable Box. Connect  
the other end of the cable to the yellow VIDEO jack on the side  
of the TV. Video cables are usually marked with yellow and are  
available from Philips or electronics retailers. Video jacks on most  
equipment are yellow.  
S-VIDEO  
DVI-I IN  
AUDIO IN  
DC IN  
16V  
R
DVI (HDCP / PC ANALOG)  
AUDIO  
IN  
Using RCA-type, stereo audio cables (not supplied), connect one  
end of the cables to the left and right Audio Out jacks of the Cable  
Box. Connect the other end of that cable to the Audio jack on the  
side of the LCD TV. Audio cables are usually marked with red and  
white and are available from Philips or electronics retailers. The  
right audio jack is red and the left audio jack is white. Match the  
cable colors to the jack colors.  
4
1
3
L
3
DC Adapter  
VIDEO  
IN  
Audio Cable  
Power  
Cable  
2
Cable  
TV signal  
Plug the DC adapter into the DC IN 16V jack on the LCD TV.  
Plug the power cable into an outlet and switch TV set on.  
Video Cable  
4
Note: Use the AV+ button on the remote control to tune to the AV  
channel for the cable box signal. Once tuned, change channels at the cable  
box, not the television.  
When you watch programs using VCR, it’s recommended to select Soft  
Mode via Auto picture.  
OUTPUT  
CH  
3
4
L
R
CABLE  
IN  
TO  
TV  
AUDIO  
OUT  
VIDEO  
OUT  
Cable Box  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
S-VIDEO CONNECTIONS  
The S-Video connection on the rear of the LCD TV can provide you  
with better picture detail and clarity for the playback of accessory  
sources such as DBS (digital broadcast satellite), DVD (digital video  
discs), video games, and VHS VCR (video cassette recorder) tapes  
than the normal antenna picture connections.  
TV  
S-VIDEO  
Connect an S-Video cable to the S-VIDEO jack of the other  
equipment (DVD Player, Camcorder, etc.) and to the S-VIDEO jack  
on the rear of the LCD TV.  
1
R
AUDIO  
IN  
DVI-I IN  
AUDIO IN  
DC IN  
16V  
L
Connect RCA-style audio cables (usually red and white) to the  
AUDIO OUT (left and right) jacks on the other equipment.  
Connect the other end of the cables to the AUDIO jack on the  
side of the LCD TV.  
DVI (HDCP / PC ANALOG)  
2
3
VIDEO  
IN  
Power Cable  
2
Plug the DC Adapter into the DC IN 16V jack on the LCD TV.  
Audio Cable  
1
3
Plug the power cable into an outlet. Turn on the LCD TV and other  
equipment.  
S-Video  
Cable  
OUT  
AUDIO  
IN  
OUT  
S
-VHS OUT  
Press the AV+ buttons to set the LCD TV to its S-VIDEO mode.  
ANTE NNA  
IN  
VIDE  
O
R
L
4
5
ANTE NNA  
OUT  
IN  
Press PLAY on the other equipment to view its material on the  
LCD TV.  
VCR or External  
Accessory Device  
(with S-Video  
Output)  
4
Note:  
The Philips LCD TV remote control can not be used to operate other video/audio  
equipment.  
The Audio jack of AV IN is shared between Video (CVBS) and S-Video signals. If Audio  
and Video is connected to S-Video input, you can still hear sound if you select Video via  
AV select, even there appears no image on screen.  
5
3
COMPONENT (HD) CONNECTIONS  
Component Video input provide the highest possible color and  
picture resolution in the playback of digital signal source material,  
such as with DVD players. If you are using a HD (High Definition)  
receiver that can transmit high definition programming, the TV can  
accept those signals through the Component input located on the  
bottom of the TV.  
Connect the component (Y, Pb, Pr) Video OUT jacks from the  
DVD player (or similar device) to the COMP(onent) VIDEO Input  
jacks on the bottom of the LCD TV.  
DVI-I IN  
AUDIO IN  
DC IN  
16V  
Y
Pb  
Pr  
L
R
1
COMPONENT VIDEO  
AUDIO IN  
DVI (HDCP  
/
PC ANALOG)  
COMPONENT HD/SD  
COMPONENT  
V IDEOCABLES  
(Green, Blue, Red)  
2
3
Audio Cable  
Connect the red and white AUDIO CABLES to the Audio (left  
and right) output jacks on the rear of the accessory device to the  
AUDIO IN jack. Connect the other end of the cable to the Audio  
jack on the rear of LCD TV.  
Power Cable  
2
Plug the DC Adapter into the DC IN 16 V jack on the LCD TV.  
Plug the power cable into an outlet. Turn on the LCD TV and other  
equipment.  
1
3
2
COMPV IDEO  
Pb  
S-V IDEO V IDEO AUDIO  
R
Y
OUT  
OUT  
OUT  
Press the AV+ button on the remote control to select HD. HD will  
appear in the upper left corner on the TV screen.  
L
Pr  
4
3
4
Insert a DVD disc into the DVD player and press the PLAY button  
on the DVD Player.  
5
5
ACCESSORY DEVICE  
EQUIPPED WITH COMPONENT  
VIDEO OUTPUTS.  
Note:  
The Philips LCD TV remote control can not be used to operate  
other video/audio equipment.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
PC (MONITOR) INPUTS:  
This LCD TV can be used as a PC. Your computer will have to be  
equipped with a VGA type video output and interface cable (not  
supplied). (One end with VGA type connector, the other end with  
DVI-I type connector.)  
Connect VGA end of the interface cable (not supplied) to the  
computer, while connecting the other ends to the DVI INPUT jack  
on the LCD TV.  
1
2
Although audio connections are not required, the LCD TV can  
reproduce the computers audio out by an AUDIO ADAPTER to  
the Audio output jack on the computer (if available) while  
connecting the other ends of the Audio cables to the PC AUDIO  
Jacks on the bottom of the TV.  
DVI-I IN  
AUDIO IN  
DC IN  
16V  
DVI (HDCP / PC ANALOG)  
3
4
Plug the DC Adapter into the DC IN 16V jack on the LCD TV. Plug  
the power cable into an outlet. Turn on the LCD TV and PC.  
Press the AV+ button until PC MODE appears on the screen.  
Audio Cable  
DVI  
Cable  
Power Cable  
HELPFUL HINT  
• For PC function, it just accepts analog input via DVI-I type connector.  
Computer  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8

Philips Breast Pump SCF154 50 User Manual
Philips CRT Television TP3681C User Manual
Philips Network Card ISP1301 User Manual
Philips Stereo System MCM298 37B User Manual
Philips Stereo System SDV2510 User Manual
Philips Universal Remote Onis 2 User Manual
Philips Work Light IS SQ6 User Manual
Pioneer Computer Drive DVD R7322 User Manual
Procom Outdoor Fireplace PL600HYLA User Manual
ProForm Treadmill 831296230 User Manual