BiliTx
Parents’ Manual
REF 1045219
* + H 9 0 6 1 0 4 5 2 1 9 0 9 *
Manufactured for
Philips Children’s MedicalVentures
191Wyngate Drive
Monroeville, PA 15146
Respironics Deutschland
Gewerbestrasse 17
82211 Herrsching, Germany
1075310
0086
HM 5/18/10
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
© 2010 Koninkljike Philips Electronics N.V. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
BiliTx
parents’manual
Table of Contents
1. Overview..................................................................................................................................................... 3
Intended Use......................................................................................................................................... 3
What is the BiliTx Phototherapy System?.................................................................................... 3
Components of the BiliTx System.................................................................................................. 4
2. Warnings, Cautions, and Symbols...................................................................................................... 5
Warnings................................................................................................................................................. 5
Cautions.................................................................................................................................................. 6
Symbols................................................................................................................................................... 7
3. Setup ........................................................................................................................................................... 9
Setup - Wrap-Around Panel ............................................................................................................. 10
Setup - Flat Neonatal Panel.............................................................................................................. 11
4. Cleaning...................................................................................................................................................... 13
Cleaning the Illuminator Device and Fiber Optic Panel ................................................................. 13
Customer Service Information........................................................................................................ 14
5. Troubleshooting....................................................................................................................................... 15
6. Specifications ............................................................................................................................................ 17
Environmental ...................................................................................................................................... 17
Physical.................................................................................................................................................... 17
Illuminator..................................................................................................................................... 17
Fiber Optic Panel......................................................................................................................... 17
Light Source........................................................................................................................................... 18
Irradiance Level............................................................................................................................ 18
Intensity Ratio .............................................................................................................................. 18
Audible Noise........................................................................................................................................ 18
Standards Compliance....................................................................................................................... 18
Electrical Requirements..................................................................................................................... 18
Disposal................................................................................................................................................... 18
Appendix A: EMC Information................................................................................................................. 19
BiliTx Warranty............................................................................................................................................... 23
Download from Www.Somanuals.com. All Manuals Search And Download.
2
BiliTx Parents’ Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BiliTx
parents’manual
1. Overview
This chapter explains how the BiliTx Phototherapy System is used to treat infant jaundice and it lists
the components of the BiliTx system.
Intended Use
The BiliTx is intended to treat hyperbilirubinemia through phototherapy.
What is the BiliTx Phototherapy System?
The BiliTx phototherapy system uses blue light emitting diodes (LEDs) to convert bilirubin to waste
products that are mostly excreted through urine and stool, thus reducing the bilirubin level in the
baby’s blood.
The Illuminator device sends light out of the fiber optic cable to the entire area of the panel.
The panel is inserted into a protective cover. This wrap is soft and comfortable and allows the
therapeutic light to be emitted towards the baby. With this use of the BiliTx system, the baby
can be held and fed and enjoy the healing comfort of parents while treatment is administered.
Additionally, when the BiliTx system is properly used with the fiber optic panel the baby’s eyes do
not need to be protected as with conventional phototherapy.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Fiber Optic Light Panel
Configuration
Components of the BiliTx System
The BiliTx system may include the following components. Note that
some components may vary from those shown below or may be
optional accessories that are not packaged with your device .
1. Illuminator Device with
AC Power Cord
2. Fiber Optic Panel
3. Disposable Cover
4
4. Illuminator Device
Carrying Case
5. System Carrying Case
(optional) (not shown)
1
6. Parents’Manual (not
shown)
7. Quick Start Guide (not
shown)
2
3
Fiber Optic Light Panel
Configuration Contents
BiliTx Parents’ Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BiliTx
parents’manual
2. Warnings, Cautions, and Symbols
Caution! US federal law restricts this device to sale by or on the order of a
physician.
Warnings
WARNING
A warning indicates the
possibility of injury to the user or
operator.
•
Use the BiliTx only for its intended use as described in this
manual.
•
•
Bilirubin photoisomers may cause toxic effects.
Do not leave the Illuminator device on when the fiber
optic panel is not around the baby.
•
•
Always turn off and unplug the Illuminator device during
cleaning or servicing.
Do not use the BiliTx system in the presence of flammable
substances such as anesthetics, cleaning agents, or gases
that support combustion (e.g. oxygen, nitrous oxide).
•
•
Do not use while bathing the baby.
Do not place or store the BiliTx system where it can fall or
be pulled into a tub or sink.
•
If the Illuminator device falls into water or if fluid is spilled
on the device do not reach for it without first unplugging
the cord. Discontinue use of the device and contact your
home care provider.
•
Never operate the Illuminator device if it has a damaged
plug or damaged or frayed power cord or wires. Do not
insert anything into the end of the plug.
•
•
Do not use an extension cord.
Always connect the device to a properly grounded outlet.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
•
If therapy is interrupted for any reason, resume therapy as
soon as possible and contact your home care provider.
•
•
Carefully place the panel cable to avoid entanglement.
Position the Illuminator device on a stable surface,
preferably lower than the infant. When the BiliTx system is
used with the fiber optic panel configuration and carrying
case, the device can hang on the outside of a crib or
treatment area.
•
•
•
Do not place the Illuminator device, power supply, or
carrying case in an incubator or infant warmer.
Do not place a temperature sensor for the infant warmer or
incubator under the fiber optic panel.
Do not place the Illuminator device, power supply, or
carrying case in a crib or other treatment area next to the
baby.
•
•
Never block the air vents of the unit or place it on a soft
surface such as a bed, crib, carpeted floor, or couch where
the air vents may be blocked.
During phototherapy, the the baby’s water balance may
become disturbed. Before and during phototherapy, make
sure the baby is properly hydrated and that his or her body
temperature is maintained.
•
•
After treatment has begun, the baby’s bilirubin level should
be measured to make sure therapy is effective.
The fiber optic panel must not be covered by anything
except with the cover provided. Any other type of cover will
cause a reduction in light intensity. The setup instructions
must be followed exactly.
Cautions
CAUTION
•
•
Keep the unit away from any heated surface.
A caution indicates the
possibility of damage to the
device.
Do not scratch, damage, or soil the ferrule end of the panel.
Also, do not place sharp or heavy items on the panel, this
can damage the panel and affect its light output.
•
•
Do not dry the fiber optic panel with artificial heat.
If the device is dropped, contact your home care provider.
BiliTx Parents’ Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Symbols
The following symbols appear on the BiliTx system.
Symbol
Explanation
Therapy On/Off
Consult accompanying instructions for use
Type BF applied part
AC Power
European Declaration of Conformity
0086
Canadian/US Safety Certification. Conforms to ANSI/UL STD. 2601.
Certified to CAN/CSA C22.2 STD. NO. 601.1.
3158805
Lock and Unlock
Chapter 2 Warnings, Cautions, and Symbols
Download from Www.Somanuals.com. All Manuals Search And Download.
8
BiliTx Parents’ Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BiliTx
parents’manual
3. Setup
Setting Up the BiliTx System
1. Place the appropriate cover on the panel and position the baby
and panel as described later in this chapter. (See Setup-Wrap
Around Panel or Flat Neonatal Panel.)
WARNING
After treatment has begun, the
baby’s bilirubin level should be
measured to make sure therapy
is effective.
2. Place the Illuminator device on a hard, flat surface or using
the carrying case, hang the unit on the outside of a crib or the
treatment area, away from any heat source. Make sure it is no
more than four feet from where the baby will be positioned.
CAUTION
Do not block any of the air vents
on the Illuminator device.
3. Insert the metal end of the light panel cable, called the
ferrule, with the metal post facing up, into the opening on
the Illuminator unit. Push the ferrule in and rotate it counter-
clockwise to lock into place. The light will not come on if the
panel is not inserted in the Illuminator device.
4. Plug the Illuminator device into an electrical outlet. The power
button will flash green.
Connecting the light panel
cable to the illuminator
device
CAUTION
If the power cord or wires need repair or replacement, do not connect the device.
5. Press the Therapy On/Off button to turn the Illuminator device
on and begin phototherapy. The Therapy button will illuminate
green.
Turning on the illuminator
device
6. To turn off the device when therapy is complete, press and hold
the Therapy On/Off button for 3 seconds.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Setup - Wrap-Around Panel
This section explains how to prepare your baby for a phototherapy
treatment using the wrap-around fiber optic light panel.
The fiber optic panel must NOT be covered by anything except with
the cover provided. Any other type of cover could cause a reduction
in light intensity. The setup instructions must be followed exactly.
This panel provides full coverage around the baby’s torso.
1. Place a disposable or reusable cover onto the panel with the
light emitting side of the panel facing the sheer side of the cover.
Wrap-around panel with
disposable cover
hook and loop tabs
2. Place the covered panel under the baby’s torso, positioning it so
it is under the baby’s armpits.
3. Wrap the panel around the baby. Use the tape or hook and loop
tabs to secure the panel around the baby.
4. If the disposable cover becomes soiled, discard it and replace
with a clean one. The cloth cover may be washed with mild soap
and water.
Positioning the fiber optic
panel
NOTES
For a larger or more active baby, you may want to tape the panel to the baby’s
diaper.
To be sure the panel is not wrapped too tightly, insert your finger between the
panel and the baby’s body. Your finger should fit easily.
You may wrap the baby in a blanket or put the baby in a sleeper.
WARNING
If using tape to secure the panel, do not adhere the tape to the baby’s skin.
Wrapping and securing the
panel
BiliTx Parents’ Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Setup - Flat Neonatal Panel
This section explains how to prepare a baby for a phototherapy
treatment using the flat neonatal fiber optic light panel.
The fiber optic panel must NOT be covered by anything except with
the disposable cover provided. Any other type of cover could cause a
reduction in light intensity. The setup instructions must be followed
exactly.
This panel is ideal for preemie or underweight infants; it may also be
used on full-term infants.
1. The protective cover for the neonatal panel is a T-vest. Slide the
vertical section of the T, with the light facing the sheer side of the
cover, onto the panel.
hook and loop tabs
Neonatal panel with t-vest
2. Lay the covered panel on a flat surface. Be sure the light
emitting side is facing up.
3. Position the baby’s chest or back directly on the panel. The cable
connected to the panel should be between the baby’s legs.
4. Secure the T-vest to the baby by first wrapping the side without
the tape or hook and loop tab around the baby’s midsection.
Then, wrap the side with the tape or hook and loop tab over the
infant. If using tape, peel off the protective cover on the tab, and
secure it. Be sure the vest is snug.
Positioning the baby on the
panel
Chapter 3 Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
12
5. If your cover has the hook and loop tabs, you can secure the
cover by pulling the hook and loop tab on the bottom corner of
the cover up and accross the cover, tightening the cover around
the cable between the baby’s legs.
6. If the T-vest becomes soiled, discard it and replace it with a new
one.
NOTES
For a larger or more active baby, you may want to tape the panel to the baby’s
diaper.
To be sure the panel is not wrapped too tightly, insert your finger between the
panel and the baby’s body. Your finger should fit easily.
You may wrap the baby in a blanket or put the baby in a sleeper.
Wrapping and securing the
T-vest
WARNING
If using tape to secure the panel, do not adhere the tape to the baby’s skin.
Using the In-Use Carrying Case
An optional, in-use carrying case is available for use with the
Illuminator device. The carrying case allows for easy mobility
during phototherapy treatment. To place the carrying case on the
Illuminator device, simply slide it over the device and adjust the
position so that the Start/Stop button is visible. The shoulder strap
should be located at the same end as the power cord. You can adjust
the shoulder strap as necessary using the hook and loop tabs.
Therapy On/Off
Button
Shoulder Strap
BiliTx Parents’ Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BiliTx
parents’manual
4. Cleaning
This section explains how to clean the BiliTx system.
CAUTION
Be sure the Illuminator device
is turned off and is unplugged
before cleaning. Do not immerse
any part of the equipment in
any liquid.
Cleaning the Illuminator Device and Fiber
Optic Panel
Follow the instructions in this section any time the Illuminator device
or fiber optic panel is dirty.
CAUTION
Keep the fiber optic panel away
from sharp objects that could
scratch or puncture the cover.
1. Use soapy water, a 10% bleach solution or full strength ammonia.
2. Use a soft sponge or cloth to apply the cleaner.
3. Apply the cleaning solution to the sponge or cloth and wipe
down the fiber optic panel and Illuminator.
WARNING
When cleaning, DO NOT USE:
• Phenolic compound based
germicide cleaner/disinfectant
4. Allow the equipment to air dry. DO NOT DRY WITH ANY MEANS
OF ARTIFICIAL HEAT.
• Gluteraldhyde disinfectant/
sterilants
5. Wipe the Illuminator device and panel with a dry cloth.
• Regular commercial cleaners or
laundry detergents
If the in-use carrying case becomes soiled, it can be wiped with a
damp cloth.
• Iodine solutions, strong acids or
strong alkali solutions
These solutions could leave
residue on the surfaces, and /
or be abrasive or harmful to the
infant.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Customer Service Information
HELPFUL TIP
Visit Philips Children’s Medical
Ventures web site at
If you need to contact Philips Children’s Medical Ventures directly, call
the Philips Children’s Medical Ventures Customer Service department
at 1-800-345-6443 or 1-724-387-4000.
You can also use the following address:
Children’s Medical Ventures, LLC
191 Wyngate Drive
Monroeville, Pennsylvania
15146 USA
BiliTx Parents’ Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BiliTx
parents’manual
5. Troubleshooting
The following is a list of problems that may occur while using the BiliTx system. For additional
information, contact your home care provider or contact Philips Children’s Medical Ventures Customer
Service at 1-800-345-6443 or 724-387-4000.
WARNING
If therapy is interrupted for one hour or longer, resume therapy as soon as possible and contact your home care provider.
Problem
Reason/Action
Therapy On/Off button is not
green
Check to make sure power cord is properly attached and
plugged into an active electrical outlet.
Ensure the device is turned on.
Therapy On/Off button is not
flashing green
If the power cord is properly attached and plugged into an
active electric outlet and the Therapy On/Off button is not
flashing green, but the device will turn on, continue to use the
device for therapy.
Light is not being emitted from Check to make sure panel is securely locked into Illuminator
fiber optic panel
device.
Yellow LED is flashing
Ensure the panel or circuit support adapter is securely locked
into place. If light continues to flash, contact your home care
provider.
Loss of power or light source
failure
Contact your home care provider.
Device will not turn off when
the Therapy On/Off button is
pressed
Press and hold the Therapy On/Off button for 3 seconds.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
BiliTx Parents’ Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BiliTx
parents’manual
6. Specifications
Environmental
Storage
-4 to 122° F (-20 to +50° C) 59 to 95° F (15 to 35° C)
15-95% Non-condensing 15-95% Non-condensing
Operating
Temperature
Relative Humidity
Physical
Illuminator
Size: 6.34 in. x 2.92 in. (16.10 cm x 7.40 cm)
Weight: <2.50 lb. (1.13 kg)
Fiber Optic Panel
Model:
EG-2000 (Wrap Around Panel)
Overall Pad Size-Standard:
Illuminated Area-Standard:
Model:
4.00”x 15.00” (10.16 cm x 38.10 cm)
3.00”x 14.00”(7.62 cm x 35.56 cm)
EG-2000N (Flat Neonatal Panel)
5.00”x 7.00” (12.70 cm x 17.78 cm)
4.00”x 6.00”(10.16 cm x 15.24 cm)
Overall Pad Size-Neonatal:
Illuminated Area-Neonatal:
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Light Source
Irradiance Level
Standard Panel-Light:
30µW/cm2/nm
55µW/cm2/nm
Neonatal Panel-Light:
Intensity Ratio
Standard Panel and Neonatal Panel : > .4 (minimum to maximum)
Audible Noise
< 60 dB(A). Measured in accordance with IEC 60601-2-50.
Standards Compliance
This device is designed to conform to the following standards:
•
•
•
IEC 60601-1 General Requirements for Safety of Medical Electrical Equipment
IEC 60601-2-50 Requirements for the Safety of Infant Phototherapy Equipment
Electromagnetic Compatibility: EN 60601-1-2, 2nd edition.
Electrical Requirements
AC Power
100-240 VAC, 50/60 Hz, 1.0 A
Class I Equipment
Type of Protection Against Electrical Shock
Degree of Protection Against Electrical Shock
Type BF Applied Part
Degree of Protection Against Ingress of Water
Mode of Operation
Ordinary Protection, IPX0
Continuous
Disposal
Dispose of this device in accordance with local regulations.
BiliTx Parents’ Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BiliTx
parents’manual
Appendix A: EMC Information
Guidance and Manufacturer’s Declaration - Electromagnetic
Emissions
This device is intended for use in the electromagnetic environment specified below. The user of this
device should make sure it is used in such an environment.
Emissions Test
Compliance
Electromagnetic Environment - Guidance
RF emissions
Group 1
The device uses RF energy only for its internal function.
Therefore, its RF emissions are very low and are not
likely to cause any interference in nearby electronic
equipment.
CISPR 11
RF emissions
Class B
The device is suitable for use in all establishments,
including domestic establishments and those directly
connected to the public low-voltage power supply
network.
CISPR 11
Harmonic emissions
IEC 61000-3-2
Class A
Voltage fluctuations/Flicker
emissions
Complies
IEC 61000-3-3
Appendix A: EMC Information
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Guidance and Manufacturer’s Declaration - Electromagnetic
Immunity
This device is intended for use in the electromagnetic environment specified below. The user of this
device should make sure it is used in such an environment.
Immunity Test
IEC 60601 Test
Level
Compliance Level
Electromagnetic Environment -
Guidance
Electrostatic Discharge
(ESD)
6 kV contact
6 kV contact
8 kV air
Floors should be wood, concrete
or ceramic tile. If floors are covered
with synthetic material, the relative
humidity should be at least 30%.
Mains power quality should be
that of a typical home or hospital
environment.
8 kV air
IEC 61000-4-2
Electrical Fast Transient/
Burst
2 kV for power supply
2 kV for supply mains
1 kV for input/output
lines
1 kV for input-output
lines
IEC 61000-4-4
lines
Surge
1 kV differential mode
2 kV common mode
1 kV differential mode
Mains power quality should be
IEC 61000-4-5
2 kV for common mode that of a typical home or hospital
environment.
Voltage dips, short
<5% UT
<5% UT
Mains power quality should be
that of a typical home or hospital
environment.
interruptions and voltage (>95% dip in UT) for 0.5
(>95% dip in UT) for 0.5
cycle
variations on power
supply input lines
IEC 61000-4-11
cycle
40% UT
40% UT
(60% dip in UT) for 5
cycles
(50% dip in UT) for 5
cycles
70% UT
70% UT
(30% dip in UT) for 25
cycles
(30% dip in UT) for 25
cycles
<5% UT
<5% UT
(>95% dip in UT) for 5 sec (>95% dip in UT) for 5 sec
3 A/m 3 A/m
Power frequency (50/60
Hz) magnetic field
IEC 61000-4-8
Power frequency magnetic fields
should be at levels characteristic of a
typical location in a typical hospital
or home environment.
NOTE: UT is the a.c. mains voltage prior to application of the test level.
BiliTx Parents’ Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Guidance and Manufacturer’s Declaration - Electromagnetic
Immunity
This device is intended for use in the electromagnetic environment specified below. The user of this
device should make sure it is used in such an environment.
Immunity Test
IEC 60601 Test
Level
Compliance
Level
Electromagnetic Environment - Guidance
Portable and mobile RF communications equipment
should be used no closer to any part of the device,
including cables, than the recommended separation
distance calculated from the equation applicable to
the frequency of the transmitter.
Conducted RF
3 Vrms
3 Vrms
3 V/m
Recommended separation distance:
IEC 61000-4-6
150 kHz to 80 MHz
d = 1.2
150 kHz to 80 MHz
Radiated RF
3 V/m
IEC 61000-4-3
80 MHz to 2.5 GHz
d = 1.2
d = 2.3
80 MHz to 800 MHz
800 MHz to 2.5 GHz
Where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter
manufacturer and d is the recommended separation
distance in meters (m).
Field strengths from fixed RF transmitters, as
a
determined by an electromagnetic site survey
,
should be less than the compliance level in each
b
frequency range
.
Interference may occur in the vicinity of equipment
marked with the following symbol:
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from
structures, objects, and people.
a: Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur
radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the
location in which the device is used exceeds the applicable RF compliance level above, the device should be observed to verify normal
operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating the device.
b: Over the frequency range 150 kHz to 80 MHz, the field strengths should be less than 3 V/m.
Appendix A: EMC Information
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Recommended Separation Distances between Portable and Mobile
RF Communications Equipment and this Device
The device is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of this device can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile RF
communications equipment (transmitters) and this device as recommended below, according to
the maximum output power of the communications equipment.
Rated Maximum Power
Output of Transmitter
(W)
Separation Distance According to Frequency of Transmitter
(m)
150 kHz to 80 MHz
80 MHz to 800 MHz
800 MHz to 2.5 GHz
d = 1.2
0.12
0.38
1.2
d = 1.2
0.12
0.38
1.2
d = 2.3
0.23
0.73
2.3
0.01
0.1
1
10
3.8
3.8
7.3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be
estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter manufacturer.
Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from
structures, objects, and people.
BiliTx Parents’ Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3
BiliTx
parents’manual
BiliTx Warranty
Children’s Medical Ventures, LLC warrants your BiliTx Phototherapy System against defects in
material and workmanship of the Illuminator device and the fiber optic panels, EG-2000 and
EG-2000N, for a period of one (1) year from the date of purchase. In addition, Philips Children’s
Medical Ventures warrants the LED light engine for 20,000 hours. This warranty does not cover
any damage to the illuminating device or the fiber optic panel caused by accident, misuse,
tampering, or negligence such as failure to follow the instructions provided in this guide. In
the event your phototherapy illumination unit fails to give satisfactory performance within
the warranty period and conditions, Philips Children’s Medical Ventures will repair or replace
your illuminating device at no charge for parts or labor. The foregoing warranties are in lieu of
all other warranties expressed or implied, including without limitation any implied warranty of
merchantability or fitness for a particular purpose.
To exercise your rights under this warranty, contact your local authorized Philips Children’s
Medical Ventures dealer or contact Philips Children’s Medical Ventures at:
191 Wyngate Drive
Monroeville, PA 15146 USA
1-800-345-6443
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
|