VR540/58
Thank you for buying a Philips video recorder. This video recorder is one of the most sophisticated
and easy-to-use video recorders (VCR) on the market. Please take the time to read this operating
manual before using your video recorder. It contains important information and notes regarding opera-
tion. The video recorder should not be turned on immediately after transportation from a cold to a
hot area or vice versa, or in conditions of extreme humidity. Wait at least three hours after transport-
ing the device. The video recorder needs this time in order to become acclimatised to its new environ-
ment (temperature, air humidity, etc.).
This video recorder is used for the recording and playback of VHS videocassettes.
Cassettes with the VHS-C label (VHS cassettes for camcorders) may only be used
with a suitable adapter.
We hope you enjoy your new video recorder.
PAL
These operating instructions have been
Important notes regarding operation
printed on non-polluting paper.
Deposit old batteries at the appropriate col-
lection points.
Danger: High voltage!
"
Do not remove the top cover as there is
Please make use of the facilities available in
your country for disposing of the packaging
of the video recorder in a way that helps to
protect the environment.
a risk of an electrical shock!
The video recorder does not contain any
components that can be repaired by the
customer. Please leave all maintenance
work for qualified personnel.
"
This electronic device contains many mate-
rials that can be recycled. Please enquire
about the possibilities for recycling your old
device.
As soon as the video recorder is connected
"
to the power supply, there are some compo-
nents that are in constant operation. To
switch off the video recorder completely you
must disconnect it from the power supply.
So that you can identify your machine for service
questions or in the event of theft, enter the serial
number here. The serial number (PROD.NO.) is
printed on the type plate fixed at the back of the
device.
Make sure that air can circulate freely
!
through the ventilation slots on the video
recorder. Do not place the device on an
unsteady base.
Make sure that no objects or liquids enter
the video recorder. Do not place vases or
the like on the video recorder. If liquid is
spilt into it, immediately disconnect the
video recorder from the power supply and
call After-sales Service for advice.
MODELNO.
PROD. NO.
VR540/58
!
...........................
This product complies with the requirements of
Directive 73/23/EEC +89/336/EEC +93/68 EEC.
Do not place any combustible objects on
the device (candles, etc.).
!
Make sure that children do not place any
foreign objects within the openings or venti-
!
lation slots.
3103 166 33791
0VMN03388/HE474ED*****
EN
1
Download from Www.Somanuals.com. All Manuals Search And Download.
6.If the connection was properly made and
your TV was automatically switched to the
programme number for the scart socket, you
will see the following picture:
PUSH MENU TO CONTINUE
I do not see a Language setting picture
* Check the cable connections.
* Repeat the channel search on your TV.
PUSH MENU TO CONTINUE
7.Save this programme number setting on your
TV for video recorder operation.
You can find more details in chapter 'Preparation
for use'.
Then, read the paragraph 'Preparation for use' in
the chapter 'Installing your video recorder'.
My screen is empty
Many TVs are switched to the programme num-
ber for the scart socket by way of a control sig-
nal sent through the scart cable.
Programme number for video recorder oper-
ation
You have now saved a programme number for
use by your video recorder as you would a reg-
ular TV channel. This programme number must
now be used in future for video recorder play-
back ('video recorder' TV channel).
If the TV does not automatically switch to the
scart socket programme number, manually
change to the corresponding programme num-
ber on your TV (see your TV's operating instruc-
tions).
Connecting additional devices
Connecting without a scart cable
You can connect additional devices such as
decoders, satellite receivers, camcorders, etc. to
the socket AV2(DECODER).
Have the following cables ready:
an aerial cable.
1.Switch off your TV.
2.Remove the aerial
cable plug from the
AV1 (TV)
AV2 (DECODER)
)
AERIAL
A
V1 (TV
(
)
aerial input socket of
the TV. Insert it into
the AERIAL at the
back of the video
recorder.
AV2 DECODER
R
I
A
U
L
T
A
R
E
F
O
A
R
E
F
R
I
A
U
L
T
O
3.Insert one end of the
supplied aerial cable
into the RF OUT at
the back of the video
recorder and the
)
AV1 (TV
RF OUT
I
A
L
T
A
R
E
F
R
U
O
other end into the
aerial input socket at
the back of the TV.
4.Insert AC cable into the wall socket.
5.Switch on your TV and select the programme
number used for video playback on your TV
set (see your TV's operating instructions).
6.Select this programme number and manually
start the TV's channel search as if you want-
ed to save a new TV channel until the next
screen appears.
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installing your video recorder
5.Check 'TIME'. If required, please change the
Preparation for use
This chapter shows you how to prepare the video
recorder use. The video recorder automatically
seeks out and stores all available TV channels.
0..9
time with the number buttons
.
6.Check if the displayed settings for 'DAY',
'MONTH' and 'YEAR' are correct.
7.When all information is correct, save by
STATUS/EXIT
'Aim' correctly
In the following sections, you require the remote
control for the first time. When using, always
aim the front of the remote control at the video
recorder and not at the TV.
pressing
.
The preparation for use is now complete.
Satellite receiver
Connecting additional devices
If you are connecting a satellite receiver, please
read the section 'Using the satellite receiver'.
Decoder
After you have connected additional devices
(satellite receiver, etc.) through the aerial cable,
switch them on. The automatic channel search
will recognise them and save them.
If you are connecting a decoder, you must
install it as described in the next section.
1.Select the desired language for the on-screen
menu by pressing PLAY B-K or STOP C-L .
MENU
Decoder allocation
2.Press
.
Some TV channels transmit encoded TV signals
which can only be viewed with a purchased or
rented decoder. You can connect such a decoder
to this video recorder. The following function will
automatically activate the connected decoder for
the desired TV channel.
3.Confirm with PROG P+ .
The automatic TV channel search starts.
PLEASE WAIT
1.Switch the TV on. If applicable, select the
programme number for the video recorder
operation.
START
❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚
FINISH
PLAY B-K
STOP C-L
0..9
to select the
2.Use
,
or
TV channel which you would like to allocate
the decoder to.
The video recorder does not find any TV
channels during the search
MENU
3.Press
. The main menu will appear.
* Select channel 1 on the TV. Can you see the
saved TV channel on the TV?
PLAY B -
K
STOP C -
L
4.Use
or
to select 'TUNER
FWD 1-
B
SET UP'. Then press
.
If not, check the cable connection of the aerial
(aerial socket), video recorder, TV.
PLAY B -
K
STOP C -
L
5.Use
or
to select 'MANU-
* The video recorder searches the entire fre-
quency range in order to find and save the
largest possible number of TV channels. It is pos-
sible that the TV channels in your country are
broadcast in a higher frequency range. As soon
as this range is reached during the search, the
video recorder will find the TV channels.
FWD 1-
B
AL TUNING'. Then press
.
PLAY B-K
STOP C-L
6.Use
or
to select 'DECODER'.
MANUAL TUNING
PROG.
CHANNEL
→DECODER
SKIP
P55
055
[OFF]
[OFF]
VIDEO MODE [SECAM]
4.'TIME' and 'DATE' will appear on the TV
screen.
SELECT CHOOSE
K
L
B
END=EXIT
FWD 1-
B
7.Use
to select 'ON'
TIME --:--
(Decoder switched on).
STATUS/EXIT
8.To end, press
.
DATE --/--/--
How can I switch off the decoder?
FWD 1-
B
Use
switched off).
to select 'OFF' (Decoder
END=EXIT
The decoder has now been allocated to this TV
channel.
EN
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual TV channel search
How do I change 'VIDEO MODE'?
If you want to change the video mode, select
In some cases it can occur that all of the TV
channels are not found and saved during the first
installation. In this case, the missing or coded TV
channels must be searched for and stored man-
ually.
PLAY B-K
STOP C-L
'VIDEO MODE' with
Then, press
or
.
FWD 1-
B
to select your desired
mode.
1.Switch on the TV set. If required, select the
programme number for the video recorder.
MENU
Using the satellite receiver
2.Press
.
The main menu will appear.
Satellite channels from a satellite receiver (con-
nected to the scart socket AV2(DECODER) ) are
received on the video recorder on programme
PLAY B-K
STOP C-L
3.Use
or
to select 'TUNER
FWD 1-
B
SET UP'. Then press
.
number 'AV2' with
.
0.0.2
PLAY B-K
STOP C-L
4.Use
or
to select 'MANU-
You should select the satelite channels to be
received by the satellite receiver directly on the
receiver itself.
FWD 1-
B
AL TUNING'. Then press
.
PLAY B-K
STOP C-L
5.Select 'PROG.' with
or
.
FWD 1-
B
.
Then press
Follow TV (Automatic TV channels
sorting)
When the automatic channel search function is
activated, the TV channels are saved in a specific
order. This may vary from the order of TV chan-
nels on the TV.
This function changes the order of TV channels
saved in the video recorder to match that of the TV.
Make sure that the video recorder and the TV
are connected by a scart cable.
MANUAL TUNING
→PROG.
CHANNEL
DECODER
SKIP
P55
055
[OFF]
[OFF]
VIDEO MODE [SECAM]
SELECT
K
L
CHOOSE
B
END=EXIT
PLAY B-K
STOP C-L
0..9
, select
6.With
or
or
the desired programme number that you want
to use for the TV channel, e.g. 'P01'. Then
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
MENU
FWD 1-
B
press
.
2.Press
3.Select 'TUNER SET UP' with
. The main menu will appear.
What is a special channel?
PLAY B-K
TV channels are transmitted in certain pre-
defined frequency ranges. These ranges are
divided into channels.
STOP C-L
FWD 1-
B
and confirm with
.
PLAY B-K
STOP C-L
4.Select 'FOLLOW TV' with
or
A specific frequency/channel is assigned to each
TV station.
FWD 1-
B
and confirm with
.
Certain frequency ranges are specified as special
channels (hyperband channels).
SELECT
K
L
CHOOSE
B
PLAY B-K
STOP C-L
7.Select 'CHANNEL' with
and confirm with
desired channel with
or
,
AUTO TUNING
MANUAL TUNING
→FOLLOW TV
MOVE
FWD 1-
B
. Then enter the
0..9
.
'
'
If you set SKIP on for a channel, this channel
will be ignored when going through the channels
END=EXIT
+
PROG P
PROG P–
with
or
.
I don't know the channels for my TV stations
5.'P:01' will appear in the video recorder display.
6.Select programme number '1' on the TV.
PLAY B-K
STOP C-L
In this case, press
or
in
'CHANNEL' to start the automatic channel
search. A changing channel number will appear
on the TV screen. Continue the automatic search
until you have found the desired TV channel.
I cannot switch my TV set to programme
number '1'
* If you have connected additional devices to
socket AV2(DECODER), please disconnect
these devices. Because of other connected
devices, the TV set could switch to the pro-
gramme number of the scart socket.
FWD 1-
B
8.Save the TV channel with
.
9.To search for other TV channels, begin again
at step 5.
STATUS/EXIT
10.To end, press
.
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FWD 1-
B
7.Confirm with
on the video
recorder remote control. The video recorder
compares the TV channels on the TV and the
video recorder.
If the video recorder finds the same TV chan-
nel as on the TV, then it stores it at 'P01'.
Sorting and clearing TV channels
manually
After you have performed the automatic channel
search you may not agree with the sequence in
which the individual TV channels have been allo-
cated to the programme positions (programme
numbers) of the video recorder. You can use this
function to individually sort the TV channels
already saved or to delete unwanted TV chan-
nels or those with poor reception.
'NO TV SIGNAL' will appear in the TV screen.
The video recorder is not receiving a video
signal from the TV.
Check the plug on the scart cable.
Check your TV's operating instructions to see
which scart socket is used for video signals.
If this does not help, it's not possible to use this
function. Please read the section 'Sorting TV
channels manually'.
1.Switch on the TV set. If required, select the
programme number for the video recorder.
MENU
2.Press
3.Select 'TUNER SET UP' with
. The main menu will appear.
PLAY B-K
8.Wait until the next number, e.g. 'P:02' appears
in the display.
9.Select the next programme number on the
TV, e.g. '2'.
STOP C-L
FWD 1-
B
and confirm with
.
PLAY B-K
STOP C-L
4.Select 'MOVE' with
or
,
FWD 1-
B
and confirm with
.
PLAY B-K
STOP C-L
5.With
or
, select the saved
FWD 1-
B
10.Confirm with
.
TV channel that you want to change.
11.Repeat steps 8 to 10 until you have assigned
a programme number to all TV channels.
STATUS/EXIT
MOVE
12.To end, press
.
→P01: 02
P02: 03
P03: 05
P04: 10
P05: 74
P06: 90
P07: 99
P08: 121
P09: 124
P10: 130
Automatic Tuning
During installation, all available TV channels are
searched for and saved. If the channel assign-
ments of your cable or satellite TV provider
change or if you are re-installing the video
recorder, e.g. after moving house, you can start
this procedure again. This will replace the TV
channels already saved with the new ones.
SELECT
K
L
CHOOSE
B
END=EXIT
FWD 1-
B
6.Confirm with
.
PLAY B-K
7.Move the selected channel with
or
STOP C-L
to the programme number you want
to assign.
8.Confirm with
9.To assign other TV channels to a programme
number, repeat steps 5 to 8.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
MENU
FWD 1-
B
.
2.Press
. The main menu will appear.
PLAY B-K
3.Select 'TUNER SET UP' with
or
10.Confirm the assignment of the TV channel
STOP C-L
FWD 1-
B
and confirm with
.
with
.
MOVE menu
PLAY B-K
4.Select 'AUTO TUNING' with
or
STATUS/EXIT
11.To exit the
, press
.
MOVE menu
STOP C-L
FWD 1-
B
.
and confirm with
PLEASE WAIT
START
❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚ ❚
FINISH
5.The automatic TV channel search starts. This
allows the video recorder to save all available
TV channels. This procedure may take sever-
al minutes.
6.When the TV channel search is complete,
'COMPLETED' will briefly appear on the TV
screen.
EN
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the language
Setting the RF out channel
In some reception locations it is possible that a
TV channel will be sent on the same or similar
frequency as the video recorder.
Result: As soon as the video recorder is
switched on, the reception quality for this or sev-
eral other TV channels will decrease.
You have the option of setting one of the dis-
played languages for the on-screen menu
(OSD).
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
MENU
The following steps will show you how to change
the pre-set 'transmission' (RF out channel) fre-
quency on the video recorder.
2.Press
. The main menu will appear.
PLAY B-K
3.Select 'INITIAL SET UP' with
or
STOP C-L
FWD 1-
B
and confirm with
.
What is RF out channel?
PLAY B-K
4.Select 'LANGUAGE' with
or
This electronic component in the video recorder
allows the device to transmit audio and video
signals via the aerial cable. These signals can
be received on a TV set just like TV channels.
What is RF out channel frequency?
This frequency or channel indicates the channel
on which the audio or video signal is transmit-
ted.
STOP C-L
FWD 1-
B
and confirm with
.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
MENU
2.Press
3.Select 'INITIAL SET UP' with
. The main menu will appear.
PLAY B-K
or
PLAY B-K
5.Select the desired language with
or
STOP C-L
FWD 1-
B
and confirm with
.
STOP C-L
.
PLAY B-K
STOP C-L
4.Select 'RF OUT' with
and confirm with
or
STATUS/EXIT
6.To end, press
.
FWD 1-
B
.
Setting the clock
SELECT
K
L
CHOOSE
B
If the display shows an incorrect time or ' --:-- ',
the time and date must be reset manually.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
MENU
→RF OUT CH
TV SYSTEM
36
K
END=EXIT
2.Press
. The main menu will appear.
PLAY B-K
3.Select 'INITIAL SET UP' with
or
FWD 1-
B
5.Press
6.Press
.
STOP C-L
FWD 1-
B
and confirm with
.
PLAY B-K
STOP C-L
0..9
,
or
to select a
PLAY B-K
STOP C-L
4.Select 'CLOCK' with
and confirm with
or
free (not allocated) channel between channel
22 and 69 in your area.
FWD 1-
B
.
FWD 1-
B
7.Press
.
TIME --:--
If you cannot get an interference-free picture
and sound, switch the built-in modulator off.
STOP C-L
DATE --/--/--
repeatedly until "--" appears
Press
next to "RF OUT CH" on the TV screen.
END=EXIT
FWD 1-
B
Then
confirm with
. In that case,
please connect your VCR to your TV with a
Scart cable.
5.Check the time in 'TIME'. If required, please
0..9
change the time with
.
6.Check 'DAY', 'MONTH' and 'YEAR' in the
PLAY B-K
STOP C-L
8.Select 'TV system' with
9.Choose 'K' or 'G' with
10.To end, press
or
.
same way.
FWD 1-
B
.
STATUS/EXIT
7.To end, press
.
STATUS/EXIT
.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Playback
Playing cassettes
Displaying current tape position
The following information is displayed on the
screen: e.g.: 0:02:45 shows the counter in hours,
minutes and seconds.
You can operate the video recorder using the
remote control or the buttons on the front of the
video recorder.
SP/LP: will show the recorded speed of your
cassette
PLAY STOP FWD
REW
If you press
while the
,
,
or
set is in Stand-by, the power will be automatical-
ly turned on. Additionally, if a cassette was
already inserted, the corresponding operation
will be performed.
'REM 0:06': will show the actual amount of play-
ing/recording time left on the tape in hours and
minutes.
When you play an NTSC cassette, the video
recorder will show 'REM -:--'.
Your video recorder can only record and play
standard VHS cassettes.
1.Put a cassette into the cassette slot. The cas-
How can I set the counter to '0:00:00'?
You can set the counter to '0:00:00' with
CLEAR
.
sette is inserted automatically. '
appear on the display.
PLAY B-K
' will
When you put a cassette in the video recorder,
the counter will automatically reset to '0:00:00'.
2.Press
to view the tape.
The counter does not move
DIGITAL STUDIO PICTURE CONTROL
This occurs when there are no recordings on a
portion of a tape. This is not a fault in your
video recorder.
Philips has developed a system which produces
the best possible playback quality. For old and
often-used video cassettes, this system reduces
interference. For new or high quality cassettes, it
emphasises the details.
The screen shows '-0:01:20'
If you rewind a cassette from the tape position
'0:00:00', the counter will show for instance,
'-0:01:20' (the cassette was rewound to 1
minute and 20 seconds before '0:00:00').
'-:--' is displayed in the 'REM' counter
This counter will automatically recognise the
length of the tape. In addition, when you put in
a cassette the video recorder must first calcu-
late the time played. Therefore, '-:--' appears
first and only after the tape has been running
for a few seconds, the correct playing time will
be shown.
Picture/ sound quality is poor
When playing rental videos or older, poorer quality
cassettes, it may not be possible to completely filter
out picture and sound interference. This is not a fault
in your machine. Read the section 'Manual tracking'.
STOP C-L
3.To stop the playback, press
or
STOP/EJECT on the video recorder.
STOP/EJECT
4.To eject the cassette, press
the video recorder stops the playback.
when
Automatic switch-off of special functions
Many functions (e.g. pause, still picture) switch
themselves off automatically after a short time in
order to protect the cassette and to save energy.
Searching for a tape position with
picture (scanning)
1.While a cassette is playing, press REW0-
s
FWD 1-
B
(reverse) or
times.
(forward) one or more
Do I need to change the playback speed
when playing back LP recordings?
During playback, the correct speed will auto-
matically be selected. For more information,
please read the section 'Selecting the recording
speed (SP or LP)' in the chapter 'Manual
recording'.
PLAY B-K
2.Press
to resume playback.
Still picture / slow motion
2
STILL
1.During playback, press
tape and display a still picture.
to stop the
SLOW
2.During playback, press
tape in slow motion.
to play the
Playing back NTSC cassettes
This video recorder can also play back cassettes
that have been recorded in SP [Standard Play]
or SLP [Super Long Play] mode in the NTSC
standard (for example, American cassettes).
However, this only works on PAL-television sets
that are suitable for a picture frequency of 60Hz.
PLAY B-K
3.Press
to resume playback.
Scanning and still/slow motion interferes with the
picture quality. The sound is switched off. This is
not a fault in your video recorder.
EN
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3
INDEX
2.For the next marking, press
and
Searching for tape position without
picture (forward wind and rewind)
FWD 1-
B
then
.
3.As soon as the video recorder finds this
marking, it automatically switches to playback.
STOP C-L
1.Stop the tape with
.
FWD 1-
B
2.Press REW0-
s
(reverse) or
Manual Tracking
(forward).
To manually adjust the tracking during playback
and slow motion playback, press
STOP C-L
3.To stop the tape, press
.
+
PROGRAMME
-
PROGRAMME
Index search
or PROG P+ PROG P– .
Tracking will return to Automatic Tracking
Adjustment when you press
tape, or press
To remove vertical jitter in a Still picture, press
Every time a tape is recorded an index marking
is written on the tape.
These marked positions can be found again
quickly and easily later.
STOP C-L
, insert a
PLAY B-K
.
+
-
or PROG P+ PROG P– .
PROGRAMME PROGRAMME
1.To search for the previous marking, press
3
INDEX
and then REW0- s .
4. Manual recording
PROG P+ PROG P–
2.Use
to select the pro-
gramme number you want to record.
General information
REC
I
3.Press
.
REC
I
4.Each time you press
you will add 30
Use 'Manual Recording' to make a spontaneous
recording (for example, a programme currently
being shown).
minutes to the recording time.
If you want to start and stop a recording manually,
read the section 'Recording without automatic
switch-off'.
If you want to start a recording manually but have
it stopped automatically, read the section
Preventing accidental erasing
All cassettes (except rental and pre-recorded
cassettes) have a security tab on the back of the
cassette.
'Recording with automatic switch-off'. (e.g. not
to record to the end of the tape)
Read the section 'Direct record' if you want to
record a programme currently being shown.
Read the section 'Automatic recording from a
satellite receiver', if you want a recording to be
controlled automatically by a satellite receiver.
To prevent recording over important recordings
(erasing), you can remove this security tab.
If you later decide to record on a protected cas-
sette, simply cover the hole with adhesive tape
or slide the tab to the right.
Lining up recordings (assemble cut)
When you add a further recording to a cassette,
which already has a recording on it, a short
blank (flicker) can appear between the old and
the new recording or the picture itself can flicker.
To help reduce these from occurring, proceed as
follows:
Recording without automatic
switch-off
1.Insert a cassette.
PROG P+ PROG P–
2.Use
to select the pro-
gramme number you want to record, for
example, 'P01'.
1.Find the tape position of the old recording
where you want to insert the new recording.
2.Look at the last minute of the old recording
(playback).
REC
I
3.To start recording, press
.
STOP C-L
4.Stop recording with
.
STILL
2
3.Press
new recording is to go and press
4.Now start recording as usual by pressing
at the tape position where the
REC
I
.
Recording with automatic switch-off
(OTR One-Touch-Recording)
REC
I
on the remote control.
STOP C-L
5.Stop recording with
.
1.Insert a cassette.
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the recording speed (SP or LP)
SELECT
K
L
CHOOSE
B
LP allows to double the recording duration on tape
(for example six hours instead of three hours on a
E180 cassette).
RECORD SPEED
DIRECT RECORD
→RECORD LINK
[SP]
[OFF]
[OFF]
END=EXIT
1.Switch on the TV set. If required, select the
programme number for the video recorder.
2.Press MENU . The main menu will appear.
PLAY B-K
FWD 1-
B
6.Select function 'ON' with
.
3.Select 'RECORD SETUP' using
or
STOP C-L
Switching off 'Record Link'
FWD 1-
B
and confirm with
.
To switch off the function, select 'OFF'
with
PLAY B-K
4.Select 'RECORD SPEED' using
or
FWD 1-
B
.
STOP C-L
.
STATUS/EXIT
7.To end, press
8.Insert a cassette.
.
SELECT
K
L
CHOOSE
B
→RECORD SPEED
DIRECT RECORD
RECORD LINK
[SP]
[OFF]
[OFF]
9.Programme the satellite receiver with the
required information (programme number of
the TV channel, start time, end time).
If necessary, please see the operating
instructions for your satellite receiver.
10.Switch off the video recorder with
END=EXIT
5.Select the required recording speed with
STANDBY/ON
y
.
FWD 1-
B
.
The video recorder is now ready to record. The
beginning and end of the recording is controlled
via scart socket AV2(DECODER).
'SP'/'LP' /'AUTO'
'SP': StandardPlay (normal recording speed) offers
the usual first-class picture quality.
'LP': LongPlay (half recording speed, double
recording time). 6 hours can be recorded on a 3-
hour cassette (E180) with a somewhat reduced
picture quality.
'AUTO': AUTOmatic Long Play. If there is not
enough space on the tape to record a pro-
grammed recording in standard speed, the record-
ing is automatically done in 'LP'. (Longplay).
Otherwise, the recording speed will be 'SP'
(Standardplay).
'Direct Record'
With Direct Record, you can record the right TV
channel in seconds even if your video recorder is
switched off. If the recording is started manually,
the video recorder uses the current TV channel
set on the TV. You will find more information on
how to switch 'Direct Record' on or off in the next
section. Make sure that your video recorder
socket (AV1/TV) and the TV are connected by a
scart cable.
STATUS/EXIT
6.To end, press
.
1.On the TV, select the programme number you
Automatic controlled recording from
a satellite receiver (RECORD LINK)
want make the recording from.
REC
I
2.Press
switched off.
3.Stop recording with
with the video recorder
This function automatically starts recording on
the switched-off video recorder when a video
signal is recognised through the connected scart
cable. If your satellite receiver has a program-
ming function, the recording will start automati-
cally (as long as the satellite receiver is switched
on).
1.Use a scart cable to connect scart socket
AV2(DECODER) on the video recorder to the cor-
responding scart socket on the satellite receiver.
2.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
STOP C-L
.
How does Direct Record work?
The video recorder compares the TV channel
selected on the TV set with its stored TV chan-
nels via the scart cable. If the same TV channel
is found, it switches the video recorder to the
corresponding programme number and starts
recording. Please do not change the TV chan-
nel on the TV set during the search so as not to
affect the process.
MENU
3.Press
. The main menu will appear.
PLAY B-K
4.Select 'RECORD SET UP' with
or
STOP C-L
FWD 1-
B
and confirm with
.
PLAY B-K
5.Select 'RECORD LINK' with
or
STOP C-L
.
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
EN
Switching 'Direct Record' on or off
SELECT
K
L
CHOOSE
B
RECORD SPEED
→DIRECT RECORD
RECORD LINK
[SP]
[OFF]
[OFF]
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
MENU
END=EXIT
2.Press
. The main menu will appear.
PLAY B-K
3.Select 'RECORD SET UP' with
or
STOP C-L
FWD 1-
B
and confirm with
.
STATUS/EXIT
5.To end, press
6.Switch off with
.
y
4.In 'DIRECT RECORD', select 'OFF' (Direct
Record off) or 'ON' (Direct Record on) with
STANDBY/ON
.
FWD 1-
B
.
5. Programming a recording (TIMER)
Selecting once/daily/weekly recordings
General information
PLAY B-K
STOP C-L
Use
following options:
'ONCE': Recording once
or
to select from the
Use a TIMER programming to automatically start
and stop a recording at a later time or date. The
video recorder will switch to the right programme
number and begin recording at the correct time.
With this video recorder, you can pre-programme
up to eight recordings within a period of one
year. To make a programmed recording, your
video recorder needs to know:
'DAILY': Repeated daily recordings from
Monday to Friday
'WEEKLY.': Repeated weekly recordings (every
week on the same day)
0..9
5.Select TIMER block with
.
0..9
6.With
buttons you can enter 'START'
(start time) , 'STOP' (end time) , 'PROG.'
(programme number) and 'DATE'.
* the date you want to make the recording
* the programme number of the TV channel
* the start and stop time of the recording
Programme numbers of the ' AV1 ' and ' AV2
' scart socket
You can also programme recordings from exter-
nal sources via scart socket AV1(TV)or AV2
(DECODER).
This information is saved in a 'TIMER' block.
Programming a recording
7.When all inputs are correct, press
STATUS/EXIT
. The programming information
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.Press MENU . The main menu will appear.
is stored in a TIMER block.
8.Insert a cassette with an intact security tab
(unprotected).
9.Switch off with
The programmed recording will only function
when the video recorder is switched off with
PLAY B-K
STOP C-L
3.Select 'TIMER' with
or
.
STANDBY/ON
y
.
FWD 1-
B
Then press
.
4.Select ONCE, DAILY, or WEEKLY recording
PLAY B-K
STOP C-L
with
or
. Then press
STANDBY/ON
y
.
FWD 1-
B
.
If any of the TIMER blocks are in use, 'FULL' will
appear on the TV screen.
SELECT
K
L
CHOOSE
B
→ONCE
DAILY
WEEKLY
TIMER LIST
END=EXIT
EN
11
Download from Www.Somanuals.com. All Manuals Search And Download.
How to check, or delete a pro-
grammed recording (TIMER)
Helpful Hints
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.Press MENU . The main menu will appear.
Error message: ' ' will flash in the video
recorder display
• No cassette was inserted. Insert a cassette and
PLAY B-K
STOP C-L
3.Select 'TIMER' with
or
.
STANDBY/ON
y
switch off the video recorder using
• A cassette was inserted with the security tab
removed.
Undo the erase protection (chapter 'Manual
Recording', section 'Preventing accidental erasing of
cassettes') or insert a different cassette.
FWD 1-
B
Then press
.
PLAY B-K
STOP C-L
4.Select 'TIMER LIST' with
or
FWD 1-
B
, and confirm with
.
SELECT
K
L
CHOOSE
B
Cassette is ejected during recording
• The end of the tape was reached during recording.
ONCE
DAILY
WEEKLY
The video recorder does not react
→TIMER LIST
• While a programmed recording is being made, you
cannot operate your video recorder manually. If you
want to cancel the programmed recording, press
END=EXIT
STOP/EJECT
.
• The end of the tape was reached during recording.
FWD 1-
B
5.Select timer block with
.
CLEAR
6.To cancel the recording, press
.
STATUS/EXIT
7.To end, press
8.Switch off with
.
y
STANDBY/ON
.
How to change a programmed
recording (TIMER)
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.Press MENU . The main menu will appear.
PLAY B-K
STOP C-L
3.Select 'TIMER' with
or
.
FWD 1-
B
Then press
.
4.Select ONCE, DAILY, or WEEKLY recording
PLAY B-K
STOP C-L
with
or
. Then press
FWD 1-
B
.
0..9
5.Select a TIMER block with
. (The flashing
number indicates an empty TIMER block.)
ONCE
TIMER - 1 2 3 4 5 6 7 8 -
SELECT TIMER NUMBER
END=EXIT
CLEAR
6.Press
to delete information and input
PLAY B-K
STOP C-L
or
correct information with
0..9
.
or
STATUS/EXIT
7.To end, press
8.Switch off with
.
y
STANDBY/ON
.
EN
12
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Other Functions
1.Switch on the TV set. If required, select the
programme number for the video recorder.
MENU
Changing the video (colour) system
2.Press
. The main menu will appear.
PLAY B-K
STOP C-L
If you playback recordings made on other video
recorders or you want to record from external
sources (via the scart socket), the automatic
video (colour) system switch-over may lead to
colour distortion.
3.Select 'VCR SET UP' with
or
FWD 1-
B
and confirm with
.
PLAY B-K
4.Select 'STATUS DISPLAY' with
or
STOP C-L
.
You can switch off the automatic TV system
switch-over as follows.
SELECT
K
L
CHOOSE
B
→STATUS DISPLAY
BLUE BACKGROUND[ON]
[ON]
Video (colour) systems
Other countries, other video (colour) systems:
In central Europe transmissions are broadcast
in the PAL system (Phase Alternation Line)
standard. France uses SECAM (Séquentiel à
mémoire). In some countries (USA and Japan),
TV viewers receive their programmes as an
NTSC signal (National Television System
Committee).
AUTO STANDBY
CLOCK DISPLAY
[OFF]
[ON]
END=EXIT
FWD 1-
B
5.Select 'ON' or 'OFF' with
.
STATUS/EXIT
6.To end, press
.
SYSTEM
1.Press
on the remote control to
select the TV (colour) system with the least
disruptions during playback.
SYSTEM
Blue Background on or off
Each pressing
, the display will change
If you want the TV screen to be solid blue when
a weak signal is received, set BLUE BACK-
GROUND to ‘ON’. The screen will be blue and
the sound will be muted. Or, if you want to
receive the weak signal, set BLUE BACK-
GROUND to ‘OFF’.
cyclicaly; AUTO, ME-SECAM, PAL.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
MENU
2.Press
. The main menu will appear.
AUTO
PLAY B-K
3.Select 'VCR SET UP' using
2.After 5 seconds, the OSD will disappear.
STOP C-L
FWD 1-
B
and confrim with
.
4.Select 'BLUE BACKGROUND' using
Which settings can I choose?
'ON': Shows the status display for a few sec-
onds only.
PLAY B-K
STOP C-L
or
.
and confirm with
FWD 1-
B
'OFF': Switches off the status display.
SELECT
K
L
CHOOSE
B
STATUS DISPLAY
[ON]
→BLUE BACKGROUND [ON]
Switching the status display off or
on
AUTO STANDBY
CLOCK DISPLAY
[OFF]
[ON]
Along with the on screen menu, the status dis-
play also displays information on the current
operating status (counter, playback, recording,
TV channel, etc.) on the TV screen. You can
switch off the information about the operating
status so that the status display is not recorded
when copying videocassettes.
END=EXIT
5.Select 'OFF' (no blue background) or 'ON'
(blue background on) with
If you select 'OFF', the menu display will disap-
FWD 1-
B
.
pear.
STATUS/EXIT
6.To end, press
.
EN
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic switch-off
Selecting the sound channel
If you haven't used the video recorder for a few
minutes in certain modes (e.g.: STOP), it will
switch to standby automatically. You can cancel
this function to use the video recorder as a tele-
vision receiver.
You can select the desired sound channel during
playback or while receiving TV channels via the
video recorder. This allows you to select a
desired language for multi-language transmis-
sions.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
MENU
AUDIO
1.Press
. This will show the current
AUDIO
until the desired setting
sound setting.
2.Press
. The main menu will appear.
2.Press
PLAY B-K
STOP C-L
appears in the display.
Reception of stereo broadcasts:
3.Select 'VCR SET UP' using
or
•
FWD 1-
B
and confrim with
.
PLAY B-K
4.Select 'AUTO STANDBY' using
or
Display on
Mode
Stereo
L
AUDIO OUTPUT
the TV screen
STOP C-L
.
L
L Audio
STEREO
LEFT
SELECT
K
L
CHOOSE
B
R
L
R Audio
L Audio
STATUS DISPLAY
[ON]
BLUE BACKGROUND[ON]
→AUTO STANDBY
CLOCK DISPLAY
[ON]
[ON]
R
L
R
L
L Audio
R Audio
R Audio
L+R Audio
L+R Audio
R
RIGHT
NONE
END=EXIT
Monaural
R
5.Select 'OFF' (no automatic switch-off) or 'ON'
FWD 1-
B
(automatic switch-off) with
.
• During playback of the recorded tape in Hi-Fi mode:
STATUS/EXIT
6.To end, press
.
Display on
the TV screen
Mode
Stereo
L
AUDIO OUTPUT
Clock Display
L
Hi Fi L Audio
Hi Fi R Audio
Hi Fi L Audio
Hi Fi L Audio
Hi Fi R Audio
Hi Fi R Audio
Normal Audio
Normal Audio
STEREO
R
L
This function allows you to switch the VCR dis-
play off. It is useful in case you feel disturbed by
the display-brightness while watching TV in a
dark room. It also reduces the power consump-
tion.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
LEFT
R
L
R
RIGHT
MONO
R
L
R
Monaural
MENU
2.Press
. The main menu will appear.
PLAY B-K
3.Select 'VCR SET UP' using
or
.
Hi Fi L Audio
L
+
Normal Audio
STOP C-L
FWD 1-
B
and confrim with
MIX
MIXED
PLAY B-K
4.Select 'CLOCK DISPLAY' using
or
Hi Fi R Audio
R
+
Normal Audio
STOP C-L
.
•
During reception of bilingual broadcasts:
SELECT
K
L
CHOOSE
B
Display on
the TV screen
STATUS DISPLAY
BLUE BACKGROUND[ON]
AUTO STANDBY
→CLOCK DISPLAY
[ON]
Mode
MAIN
SUB
AUDIO OUTPUT
[ON]
[ON]
L
Main Audio
Main Audio
Sub Audio
Sub Audio
Main Audio
Sub Audio
MAIN
R
L
END=EXIT
SUB
R
L
5.Select 'OFF' (no clock display) or 'ON' (clock
MAIN
SUB
MAIN
SUB
FWD 1-
B
display on) with
.
R
STATUS/EXIT
6.To end, press
.
14
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Before you call an engineer
If, contrary to expectation, you have any prob-
lems using this video recorder, it may be caused
by the following reasons.
Your video recorder does not respond to
any button being pressed:
* There is no power supply: check the power
No picture when you play a cassette:
* There is no recording on the cassette: change
the cassette.
supply.
* You have selected the wrong programme num-
ber on the TV for playing cassette: on the TV,
select the correct programme number for the
video recorder.
* The cable connecting the TV set and the video
recorder has come loose: check the cable.
* A programmed recording is currently being
made: if desired, cancel the programmed
recording. Please see the section 'How to check
or delete a programmed recording' in chapter
'Programming a recording'
* There is a technical problem: disconnect from
the mains power supply for 60 seconds, then
connect again.
If this doesn't help, you could reset your video
recorder to the default factory settings.
Poor picture quality when you play a cas-
sette:
* Your TV set is not properly adjusted.
* The cassette is badly worn or of poor quality:
use new cassette.
* Tracking is not properly adjusted: turn to sec-
tion 'Manual Tracking'.
Resetting devices to default factory settings
* Attention:
All the information stored (TV channels, time
and date, TIMER) will be cleared.
1.Switch off this video recorder with
No recording possible:
* The TV channel you want to record is not
stored or you selected the wrong programme
number: check TV channels stored.
* A cassette was inserted that does not have
the security tab (cannot be used to record):
Insert a cassette with an intact security tab or
change cassette. For more information, please
see the section 'Preventing accidental erasing
of cassettes' in chapter 'Manual Recording'.
STANDBY/ON
y
.
STOP/EJECT
PROGRAMME+
and
2.Press and hold
for 2 seconds or more at the same time.
Cassette is jammed in the video recorder:
* Don't use force. Pull out the mains plug for a
moment.
Remote control does not work:
There is picture or sound interference on TV
reception:
* Turn to chapter 'Installing your video recorder'
and read 'Setting the RF out channel'.
* Have your aerial checked.
* Remote control not pointed toward the video
recorder: point it at the video recorder.
* There is a technical problem: Take out the bat-
teries, wait for 10 seconds and place them
back.
* Batteries have run out: change the batteries.
You can also call the customer service centre
in your country.
The telephone numbers can be found on the
back of this instruction manual. Have the model
number (MODEL NO) and the production num-
ber (PROD.NO.) of your video recorder ready.
EN
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PHILIPS NORGE AS
Sandstuveien 70,
PO Box 1, Manglerud
N-0612 Oslo
PHILIPS AUSTRIA GMBH
Triesterstrasse 64
1101 Wien
AUSTRIA
Tel: 0810 001 203
PHILIPS PORTUGUESA, S.A.
Consumer Information Centre
Rua Dr. António Loureiro Borge, nr. 5
Arquiparque, Miraflores
P-2795 L-A-VEHLA
NORWAY
Phone: 2274 8250
PORTUGAL
Phone: 021-4163063
OY PHILIPS AB
Sinikalliontie 3
02630 Espoo
PHILIPS INFO CENTER
Alexanderstrasse 1
20099 Hamburg
PHILIPS CE, The Philips Centre,
420 - 430 London Road,
Croydon, Surrey
FINLAND
GERMANY
CR9 3 QR
puh. 09 615 80 250
Tel: 0180-53 56 767
UNITED KINGDOM
Phone: 0208-665-6350
PHILIPS KUNDTJÄNST SERVICE CONSOMMATEURS PHILIPS
PHILIPS KUNDECENTER
Frederikskaj 6,
Kista Entré
BP 0101
Knarrarnäsgatan 7
164 85 Stockholm
SWEDEN
75622 Paris Cédex 13
FRANCE
Phone: 0825-889 789
1780 København V
DANMARK
Tlf.: 80 88 28 14
Tel: (0)8 598 52 250
PHILIPS POLSKA
Al. Jerozolimskie 195B
02-222 Warszawa
POLSKA
PHILIPS ELECTRONICS IRELAND LIMITED
Consumer Information Centre
Newstead, Clonskeagh
DUBLIN 14
Phone: 01-7640292
PHILIPS REPRESENTATION OFFICE
Ul. Usacheva 35a
119048 MOSCOW
RUSSIA
Phone: 095-937 9300
TEL.: (022)-571-0-571
PHILIPS CONSUMER ELECTRONICS
Servizio Consumatori
Via Casati 23
20052 Monza - Milano
ITALY
PHILIPS INFO CENTER
Fegistrasse 5
8957 Spreitenbach
SUISSE
Tel.: 0844-800 544
Phone: 800 820026
PHILIPS Iberia, S.A.
C/Martinez Villergas, 49
28027 MADRID
SPAIN
Phone: 902-11 33 84
PHILIPS MAGYARORSZÁG KFT.
Fehérvári út 84/a.
Budapest 1119
HUNGARY
Phone: (01)-382-1700
PHILIPS CUSTOMER CARE CENTER
Twee Stationsstraat 80/
80 Rue des Deux Gares
1070 BRUSSEL/BRUXELLES
BELGIUM (for BENELUX)
Tel: 070-222303
PHILIPS CONSUMENTENLIJN
Postbus 102 5600 AC Eindhoven
NEDERLAND
Tel.: 0900-8406
EN
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|