Table of contents
'Setup' ................................................................................................................ 30
Installation of the 'External receiver 1' ...................................................... 30
Finalise set-up .................................................................................................. 32
Using the GUIDE Plus+ ® System ............................................................... 33
General ............................................................................................................. 33
The 'Grid' screen ............................................................................................ 34
The 'Search' screen ........................................................................................ 35
The 'Schedule' screen .................................................................................... 35
The 'Info' screen ............................................................................................. 36
The 'Editor' screen ......................................................................................... 36
The 'Setup' screen .......................................................................................... 36
Overview of functions ......................... 1
Functioning of the device ................................................................................ 1
The remote control ......................................................................................... 2
Additional TV functions .................................................................................. 4
Front of the device .......................................................................................... 5
Back of the device ............................................................................................ 6
Introduction ......................................... 7
Discs you can use ............................................................................................. 7
Recording and playback .................................................................................. 7
Playback only ..................................................................................................... 7
Regional code .................................................................................................... 8
Technical data ................................................................................................... 8
Accessories ........................................................................................................ 8
Important ........................................................................................................... 8
Important instructions for the HDD ........................................................... 9
Symbols used in these operating instructions ............................................ 9
Cleaning the discs ............................................................................................. 9
Special functions of your DVD recorder .................................................. 10
Recording on the HDD ..................... 37
General ............................................................................................................. 37
The Time shift Buffer ..................................................................................... 37
Symbols in the 'Time Shift Buffer' ............................................................... 38
Navigation in the time shift buffer .............................................................. 38
Mark TV shows for recording ..................................................................... 38
Manual recordings .......................................................................................... 39
OTR recordings .............................................................................................. 39
Direct Record ................................................................................................. 40
Switching 'Direct Record' on or off ........................................................... 40
Automatic recording from a satellite receiver (sat recording) ............ 40
Recording from a video recorder/DVD player ....................................... 41
Recording from a camera connected to the front sockets .................. 41
Connecting the DVD recorder ......... 13
Preparing the remote control for operation ........................................... 13
Using your DVD-Recorder remote control with your TV set ............ 13
Connecting to the aerial ............................................................................... 14
Connecting to the TV ................................................................................... 14
Connection with scart cable ........................................................................ 14
Connection with an S-Video(Y/C)cable .................................................... 15
Connection with video (CVBS) cable ........................................................ 15
Connection with the aerial cable only ....................................................... 15
Connecting to the mains .............................................................................. 16
Programming a recording (TIMER). 43
General ............................................................................................................. 43
Programming recordings with the GUIDE Plus+® System .................... 43
Programming recordings with the ShowView® System ......................... 44
Programming recordings without the ShowView® System ................... 45
How to change or delete a programmed recording (TIMER) ............. 46
Cancel a programmed recording in progress .......................................... 47
Connecting additional devices .......... 17
Connecting additional devices to the second scart socket ................... 17
Connecting a video recorder, DVD player. ............................................. 17
Connecting an external receiver ................................................................ 17
Connecting additional devices only via aerial cable ................................ 18
Connect camcorder to the front sockets ................................................ 18
Connecting audio devices to the analogue audio sockets .................... 19
Connecting audio devices to the digital audio sockets .......................... 19
Playback from the HDD .................... 48
General ............................................................................................................. 48
Additional playback features ........................................................................ 48
Search by time ................................................................................................. 48
Repeat ............................................................................................................... 48
Zoom feature .................................................................................................. 49
The media browser ....................................................................................... 49
Symbols in the 'Media Browser' .................................................................. 49
Change order for the media browser ....................................................... 50
Change title settings ...................................................................................... 50
Edit title ............................................................................................................ 51
'Video edit' ....................................................................................................... 51
Editing recorded titles (name) ..................................................................... 52
Divide title ....................................................................................................... 52
Delete titles/recordings from the HDD ................................................... 53
Insert/remove chapter markers .................................................................. 53
Hide chapters (sections) ............................................................................... 54
Installation .......................................... 20
Initial installation ............................................................................................. 20
Using a satellite receiver ............................................................................... 22
Additional installation features ........ 23
Allocating a decoder ...................................................................................... 23
Manual TV channel search ............................................................................ 23
Sorting TV channels automatically (Follow TV) ...................................... 24
Automatic TV channel search ..................................................................... 25
Sorting and deleting TV channels manually .............................................. 26
Setting the language ....................................................................................... 26
Setting the time ............................................................................................... 27
Connection using a component video (Y Pb Pr/YUV) cable (no
Recording on a DVD+RW/+R ........... 55
Archiving (storing) titles on a DVD+RW/+R .......................................... 55
Protect disc against accidental recordings ................................................ 55
progressive scan) ............................................................................................ 27
Playback from a disc .......................... 56
General notes on playback ........................................................................... 56
Switch over to the actual TV channel during playback .......................... 56
Inserting a disc ................................................................................................ 56
®
The GUIDE Plus+ System ................ 29
General information ...................................................................................... 29
Setting up the GUIDE Plus+® System ........................................................ 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of functions
Functioning of the device
Your Philips DVD/HDD recorder mainly consists of the following components:
HDD recorder
For recording in a temporary storage on the HDD (Time shift Buffer)
As soon as you turn on the DVD/HDD recorder, it automatically records the current TV channel selected on the DVD/HDD recorder in this
temporary storage. As a result, you can 'rewind' to a scene ( D ) or watch a still picture ( PAUSE 9 ), while the current TV show is still being
recorded.
Recordings in the time shift buffer are only temporarily available (factory settings: 3 hours).
For storing recordings on the HDD
You can mark recordings in the time shift buffer for storage on the HDD using REC/OTR n .
These recordings will be transferred to the HDD when you switch off the device using STANDBY m or when the time periode of the time shift
buffer ( e.g. 3 hours) expires.
DVD Recorder
For archiving (copying) HDD recordings on a DVD+RW/+R
Recordings on the HDD can be selected in a title overview screen (Media Browser) and then copied (archived) on a DVD+RW/+R.
TV tuner
For recordings independently from your TV set
You can use your DVD/HDD recorder as a TV tuner, allowing you the comfort of pausing a running TV show and continue watching it later. You
can make recordings on the HDD without having to turn on the TV set.
DVD/CD/MP3 player
For playing back recorded DVDs, CDs , CD RW/Rs
You can use this device to play back DVD+R/RWs, DVD-R/RWs, (S)Video CDs(CD-RW/R), Audio CDs(CD-RW/R), MP3 CDs(CD-RW/R) of the
respective standard.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of functions
The remote control
REC/OTR n Record the current TV show on the HDD, mark recordings in the time
shift buffer to be stored on HDD.
Hold button down to start the recording from now. (Mark the
recording from the beginning of the actual position in the Time Shift
Buffer).
STANDBY m To switch set on or off, interrupt menu function.
A programmed recording (TIMER) or an archiving process will be
continued until the end, and the device will then be switched off.
CAM Switch to 'Camera mode' (recording directly on the HDD and not
through time shift buffer), switch to input sockets (' S-VIDEO
(CAM1) / VIDEO (CAM1) ', ' DV IN (CAM2) ').
TV/HDD Switches scart socket EXT2 AUX-I/O of the DVD recorder directly to
the TV set. This lets you watch the picture from any unit connected to
this scart socket (set-top box, video recorder or satellite receiver) and
at the same time record from another source.
If you have not connected a device to the EXT2 AUX-I/O socket or
the device is switched off, you can use this button to switch between
TV reception and the signal of the DVD recorder.
This, however, functions only if you have connected your TV set to the
DVD recorder using a scart cable (socket EXT1 TO TV-I/O ) and your
TV set reacts to the switching.
RETURN Return to previous menu on a video CD (VCD). This also works with
some DVD discs.
Moreover, you can jump back to the previous scene of the time shift
buffer or to playback from the HDD. You can switch to the picture of
the actual running TV show with the TUNER buttoen.
EDIT Call up/Cancel the edit menu.
Call up/Cancel the menu for editing titles during playback.
TIMER s To make a TIMER programming with/without ShowView® system or to
alter/clear programmed recordings.
SELECT Select function/value.
You can mark several titles in the media browser.
Switch on repeat play during playback from a disc.
TUNER This button lets you switch to the picture of the internal tuner (TV
channel).
During play back from the Time Shift Buffer, you can jump to the actual
TV show (live) of the selected TV channel.
SYSTEM MENU Call up/Cancel the system menu.
Depending on the operating mode from which you press this button:
•) DVD system menu: Press DISC MENU first.
•) HDD system menu: Press TUNER first.
DISC MENU For displaying the DVD menu or the index screen overview.
INFO For displaying additional information on the screen or the time shift
buffer during playback/recording on the HDD ( TUNER / BROWSER
HDD button).
Call up additional information in the GUIDE Plus+® system.
RED Red function button, in some screens the function of a 'clear' button.
GREEN Green function button
YELLOW Yellow function button
BLUE Blue function button
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of functions
BROWSER HDD Call up/cancel the overview of HDD recordings (media browser).
GUIDE/TV Call up/Cancel the GUIDE Plus+® System
A B Cursor buttons up, down in the menus.
Previous or next position in the time shift buffer during playback from
HDD.
D C Cursor buttons left, right in the menus.
Previous or next position during playback of a title from the HDD
(media browser or time shift buffer). If you hold down this button you
can faster brwose trough the recordings. The speed will increase
automatically.
OK Confirming of functions
Starting the playback from the beginning in the 'Media Browser'.
STOP h Stop playback
Hold down the button to open and close the disc tray.
PAUSE 9 If this button is pressed during playback, the DVD recorder switches to
pause. You will see a still picture. If this button is pressed during
recording in the 'Camera mode', the DVD recorder switches to pause
and inserts a chapter marker.
PLAY G Play back a recorded disc.
In the GUIDE Plus+® system: OK button.
CHANNEL q Next programme number
CHANNEL r Previous programme number
JUMP BACK To jump back a certain time period that can be changed in the settings
of the HDD.
N Briefly press the button during playback: Previous chapter or previous
title
Hold down the button: Search backwards
Hold down the button during the still picture: slow motion backwards
O Briefly press the button during playback: Next chapter or next title
Hold down the button: Search forwards
Hold down the button during the still picture: slow motion forward
JUMP FWD To jump forward by a certain time period that can be changed in the
settings of the HDD.
0..9 For entering numbers or characters at the corresponding entry fields.
T/C Switching between title and chapter for selection using N , O .
If 'INFO' appears in the display, the index menu from a recorded disc
will be shown or an introductory film will be played. In this case, this
function is not available.
DISC MANAGER Call up/Cancel the disc manager (DM).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of functions
Additional TV functions
With the enclosed multicode remote control you can control the main functions of your TV set.
To do this, you must first enter a code number that corresponds to the make of your TV set.
You will find a summary of all available remote control commands on the last page of this manual.
How to enter this code number you will read in the chapter ' Using your DVD-Recorder remote
control with your TV set'.
TV VOLUME q Increase TV volume
TV VOLUME r Reduce TV volume
For the following functions you need to hold down the • TV button (on the left side) and then
select the function you need with the appropriate button.
STANDBY m Switch on/off TV set
0..9 Number buttons 0 - 9
CHANNEL q To select a higher programme number
CHANNEL r To select a lower programme number
Additional TV functions for Philips TV-sets if supported from the TV. You need to hold down the •
TV button (on the left side).
T/C switch Teletext (TXT) on/off
TIMER s Clock display on the screen on/off
RETURN To return to the previous selected TV program/ previous menu step
SYSTEM MENU Call up the System Menu from the TV
B , A In the menus cursor up/down
D , C In the menus cursor left/right
OK Confirm functions or settings
Colour buttons Colour buttons for special functions
TUNER Switching the TV from the external sockets to the internal tuner.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of functions
G : Play back a recorded disc or a title on the HDD
Front of the device
N : : select previous title/search backwards
O : : select next title/search forwards
STANDBY-ON m : To switch device off / on, interrupt a function.
TRAY LED : Red light around the disc tray indicates recording on a
h : Interrupt playback/recording (Cameramode)
DVD+RW/+R.
OPEN/CLOSE J : Open/close disc tray.
Behind the flap at the right hand corner on the front
GUIDE : Call up/Cancel the GUIDE Plus+® System When GUIDE
Switching between the sockets VIDEO (CAM1) , S-VIDEO
(CAM1) is done automatically. If a signal is available at both sockets at
the same time, the signal at the S-VIDEO (CAM1) socket has priority.
If you change the socket (unplug), you must re-select the socket.
(Button CHANNEL r and then CHANNEL q )
Plus+® is active, this button lights up white.
OK : To confirm the entry/function.
HDD : Call up the media browser (overview of recordings on the
HDD).
S-VIDEO (CAM1) : Connection of SVHS/Hi8 camcorders or
During a recording on the HDD this button lights up blue.
SVHS/Hi8 video recorders (programme number 'CAM1')
UP DOWN : Cursor buttons up, down in the menus.
Moves cursor up/down in the GUIDE Plus+® system
Previous or next title in the time shift buffer during playback from
HDD.
Yellow socket
VIDEO (CAM1) : Videoinput socket : Connection of
camcorders or video recorders (programme number 'CAM1')
White/red socket
LEFT RIGHT : Cursor buttons left, right in the menus.
Previous or next position during playback of a title from the HDD
(media browser or time shift buffer).
L AUDIO R (CAM1) : Audioinput socket left/right :
Connection of camcorders or video recorders (programme
number 'CAM1')
n : Stores the current TV show on the HDD, mark recordings in the
DV IN (CAM2) : digital video input (DV format only), IEEE 1394,
FireWire to connecting a digital camcorder or other suitable
device (programme number 'CAM2').
time shift buffer to be stored on HDD.
Red light around the n button indicates:
•) a recording on a DVD+RW/+R (archiving of titles)
•) storing of a recording(s) on the HDD.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of functions
Back of the device
4MAINS Connection to the mains supply (230V/50Hz)
ANTENNA IN Connection of the aerial
TV OUT Connection of the aerial cable to the TV set
EXT2 AUX-I/O Connection of an additional device (satellite receiver,
set-top box, video recorder, camcorder, ...). Input for RGB,
S-video signals, input/output for CVBS (video) signals
EXT1 TO TV-I/O Connection of a TV set. Input for RGB, S-video
signals, input/output for CVBS (video) signals
Output sockets (AUDIO/VIDEO OUT)
S-VIDEO OUT (Y/C) Connection of an S-Video compatible TV set
VIDEO OUT (CVBS) Yellow cinch socket for the connection of a
TV set with video input (CVBS, Composite Video).
AUDIO OUT L/R White/red cinch socket for the connection of a TV
set with audio input sockets or an additional device.
COMPONENT VIDEO OUT
Red/blue/green cinch sockets for the connection of an additional
device with Component Video input (interlaced, no progressive
scan).
Output sockets (DIGITAL AUDIO OUT)
COAX OUT
For the connection of a digital audio device using a coaxial
cable(cinch cable).
OPTICAL OUT
For the connection of a digital audio device using an optical cable
(Toslink).
Output socket (G LINK™)
G-LINK Connection of the supplied G-LINK™ transmitter (remote
control) for an external receiver such as satellite receiver, set-top
box, cable TV box.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Discs you can use
Welcome to the growing family of owners of PHILIPS equipment.
Thank you for buying a HDRW 720/00-02 .
The following discs can be used in your DVD recorder for playback
and recording:
Recording and playback
DVD+RW (Digital Versatile Disc + rewriteable)
uses phase change media, the same technology on which
rewritable CDs are based. A high-performance laser is
used to change the reflective properties of the recording
layer; this process can be repeated more than a thousand
times.
Time-shift TV viewing is possible with the hard disk drive (HDD) in
your DVD-Recorder./Hard Disk By storing the recording in a time shift
buffer, you can 'rewind' to a scene you missed while the current TV
show is still being recorded.
DVD+R (Digital Versatile Disc + recordable)
Unlike a DVD+RW disc, this disc can only be written to
once. If it is not finalised after a recording, further
recordings can be added to it. Old recordings can be later
deleted but they can no longer be overwritten. The
deleted recordings (titles) are marked 'Deletedtitle '.
Before this disc can be played in a DVD player, it must be
finalised in the DVD recorder. Once this process is
complete, no further recordings can be added.
Recordings in the time shift buffer will be automatically deleted e.g.
after 3 hours if the period of the time shift buffer is set to 3 hours
(factory setting).
Moreover, you can play back a DVD disc or a recorded title from the
HDD while the current TV channel is being recorded in the
background.
You can store recordings from the time shift buffer on the built-in
HDD and transfer (archive) them later on a DVD+RW/+R disc.
Playback only
DVD Video (Digital Versatile Disc)
Furthermore your Philips DVD Recorder /Hard Disk is a device for
recording on DVD+RW/+R Discs and for playing digital video discs see
next chapter. In the rest of the user manual the DVD Recorder/Hard
Disk will be mentioned as DVD-Recorder.
is a storage medium that combines the convenience of
the compact disc with the latest digital video technology.
DVD video uses modern MPEG2 data compression
technology that enables an entire feature film to be
stored on a single five-inch disc.
Please take the time to read this operating manual before using your
DVD Recorder. It contains important information on how to set up
and operate the device.
DVD-R(DVD-Recordable)
These discs can only be played back if the recording was
made in video mode and the recording was finalised.
We hope you will enjoy your new DVD Recorder / Hard Disk,
your Philips team!
DVD-RW (DVD-Rewritable)
These discs can only be played back if the recording was
made in video mode and the recording was finalised.
If you have any problems operating the device, please read the section
entitled 'Before you call an engineer'. If this doesn't help you to
resolve the problem, please call the customer support service for
your country.
Audio CD (Compact Disc Digital Audio)
The telephone numbers and e-mail addresses can be found at the end
of this instruction manual.
You can also visit the website 'http://www.p4c.philips.com' .
Super Audio CD
(plays only the CD layer of a hybrid SACD disc)
Video CD (Format 1.0, 1.1, 2.0)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Super Video CD
Important
ACaution! Visible and invisible laser radiation. If the cover is
CD-R (CD-Recordable) with Audio/MP3 content
open, do not look at the beam.
Because of the risk of eye injuries, only qualified service
engineers should open the device and carry out
maintenance or repair work.
CD-RW (CD-Rewritable) with Audio/MP3 content
Regional code
DVDs must be marked 'ALL' for all regions or '2' for
region 2 to work in this device. Regional code 2 includes:
Europe, Japan, South Africa, Middle East (incl. Egypt).
ALASER
Typ: Semiconductor lasers InGaAlP (DVD), AlGaAs(CD)
Wavelength: 660nm (DVD), 780nm (CD)
Output power (outside the lens): 20mW (DVD+RW write),
0.8mW (DVD read), 0.3mW (CD read).
Beam divergence: 82 degrees (DVD), 54 degrees (CD)
Technical data
ADanger. High voltage! Do not open.
Do not insert objects into the ventilation slots and fan
openings!
You will find more technical data on the last cover page.
You run the risk of getting an electric shock.
Voltage: 220-240V/50Hz
AThe device does not contain any user-serviceable parts. Please
Power consumption: 38W
leave all maintenance work to qualified personnel.
Power consumption (standby): less than 3W (clock display off)
AThere are some components in the DVD recorder that keep
running as long as the recorder is connected to the power supply.
To switch off the DVD recorder completely, you must unplug it
from the power supply.
Power outage/no power: Channel and timer information remain
saved for approx. 1 year, the time is saved for approx. 12 hours.
If there is power outage during a recording on the HDD (time shift
buffer) at most the last 5 minutes before the power outage will be
lost.
AIf you disconnect the DVD recorder from the mains, make sure to
take the plug out of the wall socket and not just remove the
connector from the 4MAINS socket at the back of the unit.
Children playing near the device could suffer injuries at the free
end of the cable.
Operating position: maximum 10 degree inclination in all directions
Ambient temperature: 15 °C - 35 °C
Humidity: 25% - 75%
AMake sure that air can circulate freely through the ventilation slots
on the side and the fan opening at the back of the device to avoid
overheating. The device should be placed on a firm surface.
ADo not insert any objects into the openings or ventilation slots of
Accessories
the device.
Operating instructions
Guarantee booklet
Remote control and batteries
Aerial cable
C These operating instructions have been printed on non-polluting
paper.
C Please dispose of old batteries safely.
Mains cable
Scart cable (AV-Euro cable)
G-LINK transmitter
C Please take the packaging to your local recycling centre.
C This electronic equipment contains several materials that can be
recycled. If you are disposing of an old device, please take it to a
recycling centre.
BDo not switch on the device immediately after transport from
a cold to a warm room or vice versa, or under conditions of
extreme humidity.
Wait at least three hours after transporting the device. The DVD
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
recorder needs this time to acclimate to its new environment
(temperature, relative humidity, etc.).
Symbols used in these operating
instructions
BWhen installing the recorder in a cupboard, ensure there is a gap
of approximately 5 cm (2 inch) around the recorder to enable air
to circulate freely and prevent overheating.
The following symbols will facilitate the use of these operating
instructions.
1 Step(s) for carrying out an operation.
BMake sure that no objects or liquids enter into the DVD recorder.
Do not place vases or the like on the DVD recorder. If you spill
liquid into the recorder, immediately disconnect it from the power
supply and call after-sales service for advice.
O Another possible operating step that is not absolutely
necessary.
P Reaction of the device
BKeep the DVD recorder away from radiators and other heat
sources and protect it from direct sunlight.
When only one operation step is necessary
•
BDo not place any combustible objects on the device (candles, etc.).
You will find additional information in this section.
Important instructions for the HDD
The built-in HDD of this DVD recorder is sensitive to shocks,
temperature fluctuations, and vibrations.
Cleaning the discs
Some malfunctions (frozen or distorted picture and broken sound for
example) may be due to dirt on the disc. To avoid such problems, you
should clean your discs regularly.
Please observe the following precautions:
Avoid shocks or vibrations
•
Dirty discs should be cleaned with a soft cloth. Always wipe from
the middle to the edge.
•
•
Do not cover the ventilation openings of the cooling fan
•
Do not operate the device under high temperatures, and do not
expose it to temperature fluctuations
Do not use any solvents such as benzine, thinners, commercially
available cleaning agents, or antistatic sprays designed for vinyl
records.
•
Do not pull the mains plug from the wall outlet before the device
is switched off using STANDBY m .
•
Can I use a CD lens cleaner in the DVD recorder?
Since the optical unit (laser) of the DVD recorder operates at a higher
power level than the ones in normal DVD and CD players, such CD lens
cleaner discs may actually damage the optical unit (laser).
Before bringing the device to a workshop for repair, store all
important data of the HDD on a DVD+RW/+R. See 'The archive
function'.
The workshop will not assume any liability for the loss of the
stored data.
•
Therefore, refrain from using a CD lens cleaner disc!
Philips will not assume any liability for damage or loss of
stored data.
•
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Special functions of your DVD recorder
Your PhilipsDVD recorder has a number of special functions to make it easier to use and to
enhance your enjoyment.
You can operate the main functions on your television using your DVD-Recorder recorder remote
control, even if your television is not a Philips.
You can upgrade the software of your DVD-Recorder with a CD-ROM.
find the data and the upgrade information.
With this function you can align the sequence of the TV channels from the DVD-Recorder with
that from yor TV.
With this function the recording on the DVD-Recorder can be controlled via the scart socket.
You can use this function if you have a satellite receiver that can control other devices via a scart
cable and has a programming function (timer). For more information, consult the instruction manual
of your satellite receiver.
At the touch of a button your DVD recorder, even though it is switched off, will check which
channel is currently playing on your television and record it.
This connector is also known as a 'FireWire' or 'IEEE 1394'. This connector is used to transmit
wide digital broadband signals that are used for digital video camcorders. Audio and video signals
are transmitted using a cable. In addition to DV and Hi8 camcorders, PCs with digital video output
can also be connected to the digital input.
This screen tells you what's on the disc. Each index screen represents a recording. On the right
hand side of the screen you can also see a disc indicator that shows the position and length of the
current recording on the disc in a graphic format.
This function enables you to simply delete unwanted scenes. The relevant scenes are marked and
skipped as required. If you store (archive) such titles on a DVD+RW/+R you can decide if you want
to store the original title (with the hidden scenes) or the edited title (without the hidden scenes).
MP3 CDs can be played on this machine.
MP3 files are highly compressed music files. The data is compressed to 1/10 of the volume of the
original audio material using a special process. This means that 10 hours of music can be stored on
a single CD.
Using your DVD recorder you can record from an RGB source such as a satellite receiver using a
SCART input ( EXT2 AUX-I/O socket). Video signals for the colours R(Red), G(Green) and
B(Blue) are transmitted via separate channels. This reduces the interference that occurs with
standard video cables.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The Philips DVD recorder can play back pre-recorded DVDs and CDs. DVDs recorded using this
DVD recorder can be played back on current and future DVD players.
Dolby Digital is a standard developed by Dolby Laboratories for transmitting from 1 to 5 full-range
channels as well as a low frequency (.1) channel for a total of 5.1 discrete channels. The
loudspeakers are arranged front left, front middle, front right, rear left and rear right. This system is
currently the most common system and is used in cinemas.
With this DVD recorder each soundtrack in 2-channel Dolby Digital is recorded onto a
DVD+RW/+R.
Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic" and the double-D
symbol are trademarks of Dolby Laboratories.
This product contains copy protection technology, which is protected by US Patent Nos. 4631603,
4577216, 4819098 and 4907.093 and other intellectual property rights. Use of this copy protection
technology from Macrovision Corporation requires the approval of Macrovision. It is intended
exclusively for home use and other limited pay-per-view applications, unless Macrovision approves
some other use in writing. Modifications to the equipment, removal of components and reverse
engineering are prohibited.
Simple programming system for DVD recorders. Simply enter the programming number associated
with your television programme. You will find this number in your favourite listings magazine.
The GUIDE Plus+® System gives you an on-screen listing of what's on TV. It also lets you
program your DVD recorder by selecting the show you want to record from the list on your
screen.
You simply enter your local post code during set up and you can see the next 7 days or what's on
right now or even what's on in a favourite category such as sports or movies.
Click with your remote on the show you'd like to see or schedule. No more hassles programming
your DVD recorder! The guide information is sent together with your TV signal so there's nothing
to load or buy. The service is free!
GUIDE Plus+ is registered trademark and G-LINK is a trademark of Gemstar-TV Guide
International, Inc. and/ or its related affiliates. ShowView is a registered trademark of Gemstar-TV
Guide International, Inc. and/ or one of its related affiliates.
The GUIDE Plus+ and ShowView systems are manufactured under license from Gemstar-TV Guide
International, Inc. and/or one of its affiliates.
GEMSTAR TV GUIDE INTERNATIONAL, INC. AND/OR ITS RELATED AFFILIATES
ARE NOT IN ANY WAY LIABLE FOR THE ACCURACY OF THE PROGRAM
SCHEDULE INFORMATION PROVIDED BY THE GUIDE PLUS+ SYSTEM. IN NO
EVENT SHALL GEMSTAR TV GUIDE INTERNATIONAL, INC. AND/OR ITS
RELATED AFFILIATES BE LIABLE FOR ANY AMOUNTS REPRESENTING LOSS
OF PROFITS, LOSS OF BUSINESS, OR INDIRECT, SPECIAL, OR
CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE PROVISION OR USE
OF ANY INFORMATION, EQUIPMENT, OR SERVICES RELATING TO THE GUIDE
PLUS+ SYSTEM.
The GUIDE Plus+ and ShowView product, service and/or technology are the subject of various
European and national patents and patent applications owned by, or licensed to, Gemstar - TV
Guide International, Inc. and/or its related affiliates.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Enter the serial number here. You will need it for service queries or if your machine is stolen. The
serial number (PROD. NO.) is printed on the type plate at the back or bottom.
Made in Hungary
220-240V 50/60Hz 38W
MODEL NO. HDRW 720/00-02
PROD. NO. _______________________
This product complies with the requirements of the following directives and guidelines:
73/23/EWG (Low voltage directive) + 89/336/EWG (EMV-Directive) + 93/68 EWG (CE-Marking).
This manual was in consideration of IEC 62079
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the DVD recorder
Using your DVD Recorder remote control
with your TV set
With the enclosed multicode remote control you can control the main
functions of your TV set. To do this, you must first enter a code
number that corresponds to the make of your TV set.
You will find a summary of all available remote control codes on the
last page of this manual.
Preparing the remote control for
operation
The remote control and its batteries are packed separately in the
original DVD recorder packaging. You must install the batteries in the
remote control before use - described in the following section.
1 Take the remote control and the enclosed batteries (2 batteries).
1 Hold down the STANDBY m button.
2 Using the number buttons 0..9 , enter the code number that
corresponds to the make (manufacturer) of your TV set.
3 When you have entered the code number check that, the TV set
will responds to the TV VOLUME r or TV
VOLUME q buttons.
a My TV set will not react
b Also try to enter the other code numbers or that of other
manufacturers.
b In some cases, it is possible that your TV set will not react to the
selected code numbers. If this is the case, you unfortunately cannot
use this function.
2 Open the battery compartment, insert the batteries as shown and
then close the battery compartment.
The remote control is now ready to use.
Its range is approximately 5 to 10 meters.
a How can I reset the code?
b Enter the number 000.
'Aim' correctly
If you remove the batteries, the selected code will be stored for about 5
minutes before resetted to 000.
Aim the remote control at the DVD recorder and not at the TV set.
4 You can select one of the following functions:
TV VOLUME q increase the TV volume
TV VOLUME r decrease the TV volume
For the following functions you need to hold down the •
TV button (on the left side) and then select the function you need
with the appropriate button.
STANDBY m switch off the TV set
CHANNEL q next programme number
CHANNEL r previous programme number
Additionally on Philips TV-sets:
T/C switch Teletext (TXT) on/off
TIMER s Clock display on the screen on/off
RETURN To return to the previous menu step
SYSTEM MENU Call up the System Menu from the TV
B , A In the menus cursor up/down
D , C In the menus cursor left/right
OK Confirm functions or settings
Colour buttons Colour buttons for special functions
TUNER Switchng the TV from the external sockets to
the internal tuner (TV channels).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the DVD recorder
Connecting to the aerial
Connecting to the TV
To receive TV programmes you have to connect the DVD-recorder to
the aerial or the cable network.
Choose from the following connections:
Connection with scart cable
1 Switch off your TV set.
Connection with S videocable
Connection with Video (CVBS) cable
Connection with the aerial cable only
2 Remove the aerial cable plug from your TV set. Insert it into the
ANTENNA IN socket at the back of the DVD recorder.
3 Insert one end of the supplied aerial cable into the TV
OUT socket at the back of the DVD recorder and the other end
into the aerial input socket at the back of the TV set.
Connection with scart cable
The scart or Euro AV cable serves as the universal connector for
picture, sound and control signals. With this type of connection, there
is practically no loss of quality in picture or sound transmission.
1 Plug a scart cable into the scart socket EXT1 TO TV-I/O at the
back of the DVD recorder and the scart socket for the DVD
recorder at the back of the TV set (see TV set operating
instructions).
Several scart sockets on the TV?
Select the scart socket that is suitable for both video output and for
video input.
Selection menu for the scart socket?
On some TV sets select 'VCR' as the source for this scart socket. Read
your instruction manual for your TV set for further information.
O Read the next chapter 'Connecting additional devices' on how
to connect additional devices (satellite receivers,
videorecorders,...) to the input-/output sockets.
Then, read the chapter on 'Connecting to the mains'.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the DVD recorder
Connection with an S Video(Y/C)cable
Connection with video (CVBS) cable
This connecting cable, also known as the SVHS cable, is used to
transmit the brightness signal (Y signal) and colour signal (C signal)
separately. This mini DIN socket/plug is also called a Hosiden
socket/plug.
This cable, usually with yellow Cinch connectors, is used for
transmitting the Composite Video signal (FBAS, CVBS). In this method
of transmission the colour signal and the brightness signal are
transmitted on the same cable. In certain circumstances, this can lead
to slight problems with the picture, such as 'Moiré' patterns.
1 Insert one end of an S-Video(SVHS) cable into the S-VIDEO
OUT (Y/C) socket at the back of the DVD recorder and the other
end into the S-Video (SVHS) input socket on the TV set (usually
labelled 'S-Video in' or 'SVHS in'. See TV operating instructions).
1 Insert one end of a video (CVBS) cable into the yellow Cinch
socket VIDEO OUT (CVBS) at the back of the DVD recorder
and the other end into the video input socket (usually yellow) on
the TV set (usually labelled 'Video in' or 'AV in'. See TV operating
instructions).
2 Insert one end of an audio (Cinch) cable into the red/white Cinch
socket AUDIO OUT L/R at the back of the DVD recorder and
the other end into the audio input socket (usually red/white) on
the TV set (usually labelled 'Audio in' or 'AV in'. See TV operating
instructions).
2 Insert one end of an audio (Cinch) cable into the red/white Cinch
socket AUDIO OUT L/R at the back of the DVD recorder and
the other end into the audio input socket (usually red/white) on
the TV set (usually labelled 'Audio in' or 'AV in'. See TV operating
instructions).
O Read the next chapter 'Connecting additional devices' on how
to connect additional devices (satellite receivers,
videorecorders,...) to the input-/output sockets.
O Read the next chapter 'Connecting additional devices' on how
to connect additional devices (satellite receivers,
videorecorders,...) to the input-/output sockets.
Then, read the chapter on 'Connecting to the mains'.
Then, read the chapter on 'Connecting to the mains'.
Connection with the aerial cable only
To connect this DVD-Recorder to a TV set without external
Audio/Video input sockets, you need a modulator. With the modulator
the audio/video signal is converted in an UHF-channel. This signal can
be received and stored on the TV as a TV-station.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the DVD recorder
Connecting to the mains
Always check if the local mains voltage matches the voltage range
printed on the type plate at the back or bottom of the DVD-recorder.
If not consult your dealer or the customer support from your country.
1 Switch on the TV set.
2 Insert one end of the supplied mains cable into the mains socket
4MAINS at the back of the DVD recorder and the other end
into the wall socket.
P The most important features of the DVD recorder will appear
in scrolling text on the display.
After the first installation is completed this function will be
switched off. How you switch on this function again, read in
the chapter 'User preferences' in the section 'standby'.
Then, read the paragraph on 'Initial installation' in 'Installing your DVD
recorder'.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting additional devices
Connecting an external receiver
Connecting additional devices to the
second scart socket
1 Connect the scart socket of the receiver (satellite receiver,
set-top box, cable TV box,...) provided for the TV set (usually
labelled 'TV', 'TO TV',...) with the EXT2 AUX-I/O socket of the
DVD recorder.
O If your external receiver offers several options for the signal
available at the 'TV', 'TO TV',... socket, choose the 'RGB'
setting.
Why can't I use the 'VCR', 'TO VCR',... socket?
In order to achieve the best possible picture quality, you must use the
RGB (red-green-blue) signal of the receiver. As a rule, this signal is
available at the 'TV', 'TO TV',... socket. The DVD recorder transfers the
signal to the EXT1 TO TV-I/O socket.
Some receivers only provide a 'Video (CVBS/FBAS)' signal at the 'VCR',
'TO VCR'...socket.
If you are satisfied with the picture quality of the 'VCR', 'TO VCR',...
socket, you can also use this socket.
Read the instruction manual of the receiver which signals are available
at the sockets.
You can connect additional devices such as decoders, satellite
receivers, camcorders, etc. to the EXT2 AUX-I/O socket.
Connecting additional receivers
For additional receivers, you can also use the EXT1 TO
TV-I/O socket (if the TV set is connected to the COMPONENT
VIDEO OUT sockets).
When playback is started on this additional device the DVD recorder
automatically connects the EXT2 AUX-I/O scart socket with the
EXT1 TO TV-I/O scart socket. You will then see the picture from the
additional device on your TV set, even if the DVD recorder is switched
off.
O The TV/HDD button on the remote control allows you to
switch between playback through the EXT2 AUX-I/O scart
socket and playback from the DVD recorder.
Connecting a video recorder, DVD player.
You can also connect a video recorder or a DVD player to the EXT2
AUX-I/O input socket.
The DVD recorder must be connected directly to the TV set ( EXT1
TO TV-I/O socket directly to the TV set). If there is a video recorder
in between the picture quality may be poor because of the copy
protection system built into the DVD recorder.
O If you already have an external receiver (satellite receiver,
set-top box, cable TV box) connected to this socket, you can
connect the video recorder to the 'VCR', 'TO VCR', ...socket
of the external receiver.
O You can also use the front sockets S-VIDEO (CAM1) ,
VIDEO (CAM1) and the L AUDIO R (CAM1) audio
sockets.
For more information read the chapter 'Recording on the
HDD'.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting additional devices
Connecting additional devices only via
aerial cable
Connect camcorder to the front
sockets
If you want to connect additional devices (e.g. satellite receiver...) only
via aerial cable, please observe the following:
To copy camcorder recordings, you can use the front sockets. These
sockets are located behind the flap on the right hand side.
The DVD-Recorder must be connected directly to the TV set. If there
is a video recorder or an additional device in between, the picture
quality may be poor because of the copy protection system built into
the DVD-Recorder.
Recordings from the front sockets were stored on the HDD to make
editing easy. Then you can transfer (archive) them on a DVD+RW/+R.
Digital (DV) input socket
If you have a DV or Digital 8 camcorder, connect the DV IN
(CAM2) input of the DVD recorder to the appropriate DV output on
the camcorder.
Choose 'CAM2' as a programme number for this input.
During recording on the HDD or a DVD+RW/+R the original
recording date and time are stored as DVD subtitles.
On playback, this data can be displayed on the TV screen by using the
' ' function (Subtitle).
E
S videoinput socket
If you have a Hi8 or S-VHS(C) camcorder, connect the S-VIDEO
(CAM1) input of the DVD recorder to the appropriate S-VHS output
on the camcorder.
You must also connect the audio input L AUDIO R (CAM1) on the
DVD recorder to the audio output on the camcorder.
Choose 'CAM1' as a programme number for this input.
The additional device (satellite receiver) must be connected before the
DVD recorder (additional device - DVD recorder - TV set). Only the
TV set must be connected to the TV OUT socket.
Video(CVBS) input socket
If you have a camcorder that only has a single video output (Composite
Video, CVBS), connect the VIDEO (CAM1) input on the DVD
recorder to the appropriate output on the camcorder.
You must also connect the audio input L AUDIO R (CAM1) on the
DVD recorder to the audio output on the camcorder.
If there is interference in the picture when the additional device is
switched on, a TV broadcaster may be transmitting on the same
channel or a channel very close to that of the additional device. (e.g.:
TV broadcaster on channel 45, additional device (satellite receiver)
also on channel 45). In this case, change the channel of the additional
device (satellite receiver). Consult the instruction manual of the
additional device.
Choose 'CAM1' as a programme number for this input.
You must also store this channel on the DVD recorder to be able to
record TV programmes from the additional device (satellite receiver).
Switch on the additional device during the installation of the DVD
recorder. During the automatic channel search, the channel on which
the additional device is transmitting will be stored as a TV channel.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting additional devices
Connecting audio devices to the
analogue audio sockets
Two analogue audio sockets AUDIO OUT L/R (audio signal output
left/right) are located at the back of the DVD recorder.
These can be used to connect the following:
•) a receiver with Dolby Surround Pro Logic
•) a receiver with two channel analogue stereo
Can I use the 'Phono' input on my amplifier?
This socket (input) on the amplifier is designed only for a record player
without preamplifiers. Do not use this input for connecting the DVD
recorder.
The DVD recorder or the amplifier may be damaged as a result.
Connecting audio devices to the digital
audiosockets
At the back of the DVD recorder there are two digital audio output
sockets OPTICAL OUT for an optical cable and COAX OUT for a
coaxial cable (Cinch cable).
These can be used to connect the following:
•) an A/V receiver or an A/V amplifier with a digital
multi channel sound decoder
•) a receiver with two channel digital stereo (PCM)
Digital multi-channel sound
Digital multi-channel sound offers the best possible sound quality. You
will need a multi-channel A/V receiver or amplifier that supports at least
one of the audio formats of the DVD recorder (MPEG2 and Dolby
Digital).
Consult the operating instructions for your receiver to find out which
audio formats it supports.
a All I can hear from my loudspeakers is a loud distorted
noise
b The receiver is not compatible with the digital audio format of the
DVD recorder. The audio format of the DVD disc is displayed in the
status window when you switch to another language. Playback in
six-channel digital surround sound is only possible if the receiver has
a digital multi-channel sound decoder.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2 Select the desired language for the on-screen menu by pressing
Initial installation
B or A .
After successfully connecting your DVD recorder to the TV set and
other additional devices as described in the previous chapters, this
chapter will show you how to start the initial installation. The DVD
recorder automatically seeks and stores all available TV channels.
Virgin mode
Menu Language
English
Switching on additional devices
Español
Français
Italiano
Deutsch
If you have connected additional devices such as a satellite receiver to the
aerial cable, switch them on. The automatic channel search will recognise it
and save it. Please observe that you must switch on a "test signal" for some
additional devices.
Press OK to continue
No aerial connected
Even if you only want to use the DVD recorder to play back or have only
connected a satellite receiver, you must still complete the initial installation.
This is necessary so that the basic settings are stored correctly. Once initial
installation is complete you can use the DVD recorder as normal.
What is an on-screen menu?
The multi-language on-screen menu takes the mystery out of using your
new DVD recorder. All settings and/or functions are displayed on your
TV screen in the relevant language.
1 Press STANDBY-ON m on the front of the DVD-recorder
3 Confirm with OK .
P 'PHILIPS' and then 'IS TV ON?' will appear on the display.
P If the connection was properly made and your TV was
automatically switched to the programme number for the
scart socket, e.g. 'EXT', '0', 'AV', you will see the following
picture:
4 Select the desired audio language using B or A .
Virgin mode
Audio Language
English
Español
Virgin mode
Français
English
Italiano
Press OK to continue
Menu Language
English
Español
Français
Italiano
Deutsch
Press OK to continue
What is an audio language?
The DVD will play the sound in the language you select, provided this
language is available on the disc. If it is not available on the disc the first
language on the DVD will be used instead. The DVD Video Disc menu,
if available, will also be displayed in the language you select.
a My screen is empty.
b Depending on the initialisation procedure it can take some time
before the picture appears. Please press no button in the
meantime.
b If the TV set does not automatically switch to the scart socket
programme number, manually change to the corresponding
programme number on your TV set (see your TV's operating
instructions).
5 Confirm with OK .
6 Select the desired language for the subtitles by pressing B or
A .
b Check that the scart cable is connected from the TV set to the
EXT1 TO TV-I/O socket on the DVD recorder. The EXT2
AUX-I/O socket is intended only for additional devices.
Virgin mode
Subtitle Language
English
Español
Français
English
Italiano
Press OK to continue
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
A Confirm with OK .
What is the subtitle language?
P A screen appers with a message about the connection of the
aerial.
The subtitles will be displayed in the language you select, provided this
language is available on the disc. If it is not available on the disc the fist
language on the DVD will be used instead.
It can take some time before this screen appears. Please press
nobutton in the meantime.
7 Confirm with OK .
8 Select the desired screen format position using B or A .
B After you connect the aerial (or cable TV, satellite receiver, etc.)
to the DVD recorder, press OK .
P The automatic TV channel search starts.
Virgin mode
TV Shape
4:3 letterbox
4:3 panscan
16:9
Installation
Autom. search
Searching for TV channels
00 Channels found
Press OK to continue
Please wait
O '4:3 letterbox'
for a 'wide-screen' (cinema format) picture with black bars at
the top and bottom.
P 'WAIT' will appear on the display.
Wait until all available TV channels have been found. This can
take several minutes.
O '4:3 panscan'
for a full-height picture with the sides trimmed.
O '16:9'
a No TV-Stations found yet?
for a wide-screen TV set (screen edge ratio 16:9)
b Select channel 1 on the TV set. Can you see the stored TV channel
on the TV set?
If not, check the cable connection from the aerial (aerial socket) to
the DVD recorder and to the TV set.
9 Confirm with OK .
0 Select the country of your residence with B or A .
b Please have patience.
O If your country does not appear, select 'Other'.
The DVD recorder searches the entire frequency range in order to
find and save the largest possible number of TV channels.
b If you have not connected an aerial, go through all the basic settings
right to the end and then, if you wish, start the automatic search (see
'Automatic TV station search').
Virgin mode
Country
Austria
Belgium
Denmark
Finland
P When the automatic TV channel search is complete, 'Autom.
search complete' will appear on the TV screen along with
the number of TV channels found.
P 'Time', 'Year', 'Month', 'Date' will then appear on the TV
screen. It can take some time before this screen appears.
Please press nobutton in the meantime.
France
Press OK to continue
Why do I have to set the country?
Autom. search
To call up the specific settings for the respective country, you must first
install the country.
After the first installation you can set the country in the 'Setup' of the
GUIDE Plus+® System only.
Autom. search complete
00 Channels found
Time
Year
Month
Date
20:01
2003
01
01
To continue
Press OK
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
C Check the displayed settings for 'Time', 'Year', 'Month' and
'Date' .
O If required, change the data with the number buttons 0..9 on
your remote control.
O Select the line with A or B .
À If all informations are correct, save by pressing OK .
P 'Dealer demo' appears on the screen.
O Select 'Yes' and confirm with OK if you want to see a
demonstration of the function of the DVD-Recorder. Playback
starts automatically.
The demontration movie is stored for each language as a title
in the 'Media Browser'. If you need additional capacity on the
HDD you can delete the demonstration as you delete a titel
(recording). Read therefor the section 'Delete titles/recordings
from the HDD' in the chapter 'Playback from the HDD'.
O Select 'No' and confirm with OK if you do not want to see
the demonstration movie automatically.
The initial installation is now complete.
How to modify the channel settings or the time/date settings you will
red on the following chapter.
a Sound may be distorted on some TV channels.
b If the sound is distorted on any of the stored TV channels or if there is no
sound at all, the wrong TV system may have been stored for the TV
channel. Read 'Manual TV channel search' for information on how to
change the TV system.
Using a satellite receiver
TV channels from a satellite receiver (connected to scart socket EXT2
AUX-I/O ) are received on the DVD recorder on programme number
'EXT2'
If necessary, use the TUNER button to switch to the internal tuner.
Select programme number 'EXT1' with 0 on the remote control and
then select programme number 'EXT2' with CHANNEL r .
You should select the TV channels to be received by the satellite
receiver directly on the receiver itself.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional installation features
A To end, press SYSTEM MENU .
Allocating a decoder
Your decoder has now been allocated to this TV channel.
Some TV channels send coded TV signals that can only be viewed
properly with a purchased or rented decoder. You can connect such a
decoder (descrambler) to your DVD recorder. The following function
automatically activates the connected decoder for the TV channel you
want to watch.
Manual TV channel search
In some cases, not all of the available TV channels may have been found
and stored during initial installation. In this case, you will need to search
for and store the missing or coded TV channels manually.
Preparation:
•) The TV set is switched on, and if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
Preparation:
1 Use the CHANNEL q and CHANNEL r buttons or the
number buttons 0..9 on the remote control to select the TV
channel for which you want to use the decoder.
•) The TV set is switched on, and if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
O If necessary, use the TUNER button to switch to the internal
1 Press the DISC MENU button and then the SYSTEM
MENU button on the remote control.
tuner.
P The 'SYSTEM MENU' appears.
2 Press the BROWSER HDD button and then the SYSTEM
MENU button on the remote control.
2 Select 'Set up' using B .
P The 'SYSTEM MENU' appears.
3 Press C to select 'System'.
3 Select 'Set up' using B .
4 Select the line 'Installation' using B and confirm with C .
P A message appears on the screen that this setting will flush the
'Time Shift Buffer'.
4 Press C to select 'System'.
5 Select the line 'Installation' using B and confirm with C .
P A message appears on the screen that this setting will flush the
'Time Shift Buffer'.
O If the 'Time Shift Buffer ' contains important recordings, save
them with the REC/OTR n button first. Read additional
information to the 'Time Shift Buffer' in the chapter 'The Time
Shift Buffer'.
O If the 'Time Shift Buffer ' contains important recordings, save
them with the REC/OTR n button first. Read additional
information to the 'Time Shift Buffer' in the chapter 'The Time
Shift Buffer'.
5 Select 'Yes' with D and confirm with OK .
O If the message window was closed, confirm the line with
C again.
6 Select 'Yes' with D and confirm with OK .
O If the message window was closed, confirm the line with
6 Select 'Manual search' using B or A and confirm with C .
C again.
7 Select 'Manual search' using B or A and confirm with C .
Installation
Manual search
Installation
Manual search
Channel/freq.
Entry/search
CH
01
Channel/freq.
Entry/search
CH
01
Programme number 01
TV channel name
Decoder
BBC1
Programme number 01
Off
TV channel name
Decoder
BBC1
TV system
NICAM
PAL-BG
Off
On
0
To store
Press OK
TV system
NICAM
PAL-BG
Fine tuning
On
0
To store
Press OK
Fine tuning
7 In 'Channel/freq.', select the desired display using C .
'Freq.'(Frequency), 'CH'(Channel), 'S-CH'(Special/hyperband
channel)
8 Select 'Decoder' using B or A .
9 Select 'On' with C .
8 In 'Entry/search', enter the frequency or channel of the TV
station using the number buttons 0..9 .
O To switch off the decoder use C to select 'Off' (Decoder
switched off).
O Press C in the line 'Entry/search' to start the automatic
search.
P A changing channel number/frequency number will appear on
0 Confirm with OK .
the TV screen.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional installation features
Continue the automatic search until you have found the TV
channel you are looking for.
Sorting TV channels automatically
(Follow TV)
9 Using D or C in 'Programme number', select the programme
number you want to use for the TV channel, e.g. '01'.
This function changes the order of the TV channels stored in your
DVD recorder to match the order on the TV set.
This only works if the DVD recorder ( EXT1 TO TV-I/O socket) and
the TV set are connected with a scart cable.
0 Press OK to store the TV channel.
A To search for other TV channels, begin again at 8 .
Preparation:
O Change the name of a TV channel:
- In 'TV channel name', press C .
•) The TV set is switched on, and if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
- Select the desired character position using D or C .
- hange the character at the desired position with B or A .
- Select the next character position in the same way.
- Confirm with OK .
1 Press the BROWSER HDD and then the SYSTEM
MENU button on the remote control.
P The 'SYSTEM MENU' appears.
O Change the TV system of the TV channel:
- In 'TV system', use D or C to select the TV system that
produces the least distortion of picture and sound.
2 Select 'Set up' using B .
3 Press C to select 'System'.
O NICAM
- If reception is poor and the sound distorted you can turn off
NICAM.
In 'NICAM', select 'Off' using C .
4 Select the line 'Installation' using B and confirm with C .
P A message appears on the screen that this setting will flush the
'Time Shift Buffer'.
O Fine tuning
O If the 'Time Shift Buffer ' contains important recordings, save
them with the REC/OTR n button first. Read additional
information to the 'Time Shift Buffer' in the chapter 'The Time
Shift Buffer'.
- You can try fine tune the TV channel manually with D ,
C in the line 'Fine tuning'.
B To end, press SYSTEM MENU .
5 Select 'Yes' with D and confirm with OK .
O If the message window was closed, confirm the line with
C again.
6 Select line 'Follow TV' with B or A . and confirm with the
C button.
7 Confirm the message on the screen with OK .
P 'TV 01' will appear in the DVD recorder display.
TV 01
8 Select programme number '1' on the TV set.
a I cannot switch my TV set to programme number '1'
b If you have connected additional devices to the EXT2 AUX-I/O socket,
please disconnect these devices. Other connected devices may have
switched the TV set to the programme number of the scart socket.
9 Confirm with OK on the DVD recorder remote control.
P 'WAIT' will appear in the display.
P The DVD recorder compares the TV channels on the TV set
and the DVD recorder.
If the DVD recorder finds the same TV channel as on the TV
set it stores it at 'P01'.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional installation features
a 'NOTV' will appear in the display.
The DVD recorder is not receiving a video signal from the TV set.
b Chech the connectors at both ends of the scart cable.
b Check your TV's operating instructions to see which scart socket is used
for video signals.
b If the problem persists, you won't be able to use this feature.
Please read 'Sorting and deleting TV channels manually'.
Automatic TV channel search
If the channel assignments of your cable or satellite TV provider change
or if you are reinstalling the DVD recorder, e.g. after moving house,
you can start this procedure again. This will replace the stored TV
channels with the new ones.
0 Wait until for example 'TV 02' appears in the display.
Preparation:
•) The TV set is switched on, and if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
TV 02
1 Press the BROWSER HDD button and then the SYSTEM
MENU button on the remote control.
P The 'SYSTEM MENU' appears.
A Select the next programme number on the TV set, e.g. '2'.
2 Select 'Set up' using B .
B Confirm with OK on the DVD recorder remote control.
3 Press C to select 'System'.
O If you confirmed the wrong TV channel, you can delete the
last allocation with D .
4 Select the line 'Installation' using B and confirm with C .
P A message appears on the screen that this setting will flush the
'Time Shift Buffer'.
C Repeat steps 0 to B until you have assigned all the TV
channels from your TV set.
O If the 'Time Shift Buffer ' contains important recordings, save
them with the REC/OTR n button first. Read additional
information to the 'Time Shift Buffer' in the chapter 'The Time
Shift Buffer'.
À To end, press SYSTEM MENU .
a 'Switch off recorder, new preset' appears on the screen
b In order to transfer the new TV channel order to the GUIDE Plus+®
system, it is necessary to switch off the DVD recorder ( STANDBY m ).
Wait for approx. 4 minutes before you switch the DVD recorder on again.
b If this message appears after you switch on the DVD recorder, it was not
possible to complete the transfer process. Switch off the DVD recorder
using STANDBY m .
5 Select 'Yes' with D and confirm with OK .
O If the message window was closed, confirm the line with
C again.
6 Select 'Autom. search' using B or A .
7 Press C .
P The automatic TV channel search starts. This allows the DVD
recorder to save all available TV channels. This procedure may
take several minutes.
Installation
Autom. search
Searching for TV channels
00 Channels found
Please wait
P When all the TV channels have been found, 'Autom. search
complete' will appear on the TV screen.
8 To end, press SYSTEM MENU .
You can read about how to search for a TV channel manually in
'Manual TV channel search'.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional installation features
A To store, press OK .
Sorting and deleting TV channels
manually
B To end, press SYSTEM MENU .
a 'Switch off recorder, new preset' appears on the screen
b In order to transfer the new TV channel order to the GUIDE Plus+®
system, it is necessary to switch off the DVD recorder
( STANDBY m ). Wait for approx. 4 minutes before you switch
the DVD recorder on again.
With this function you can rearrange the TV channels already stored or
to delete TV channels you don't want or those with poor reception.
Preparation:
b If this message reappears after you switch on the DVD recorder, it
was not possible to complete the transfer process.
Switch off the DVD recorder using STANDBY m .
•) The TV set is switched on, and if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
1 Press the BROWSER HDD button and then the SYSTEM
MENU button on the remote control.
P The 'SYSTEM MENU' appears.
Setting the language
2 Select 'Set up' using B .
For the basic setting of DVD playback, you can select the language for
the subtitles and the audio language.
3 Press C to select 'System'.
Please note that with some DVDs the audio language and/or subtitle
language can be changed only via the DVD menu.
For bilingual shows, you can also select the sound channel of the TV
station via the internal tuner ( TUNER button) for recording or
playback.
4 Select the line 'Installation' using B and confirm with C .
P A message appears on the screen that this setting will flush the
'Time Shift Buffer'.
O If the 'Time Shift Buffer ' contains important recordings, save
them with the REC/OTR n button first. Read additional
information to the 'Time Shift Buffer' in the chapter 'The Time
Shift Buffer'.
Preparation:
•) The TV set is switched on, and if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
5 Select 'Yes' with D and confirm with OK .
1 Press the BROWSER HDD button and then the SYSTEM
MENU button on the remote control.
O If the message window was closed, confirm the line with
C again.
P The menu bar appears.
6 Select 'Sort TV channels' using B or A and confirm with C .
2 Select ' ' symbol with D or C .
A
3 Select line ' ' with B or A and confirm with the C button.
u
Installation
Sort TV channels
...
•
P01 BBC1
P02 BBC2
P03 ITV
P04
P05
Language
P06
Audio Language
Subtitle
English
English
English
...
Menu
To sort
Press ›
To exit press
SYSTEM MENU
7 Using B or A select the TV channel that you want to delete or
whose order you want to change.
4 Select the appropriate line and confirm with C .
8 Confirm with C .
O Audio Language
O Deleting TV channels
The DVD will play back in the language you have chosen.
Unwanted channels or those with poor reception can be
deleted using the red function button.
O 'Subtitle'
Subtitle language
9 Using B or A , shift the TV channel to the desired position and
press the D button.
O 'Menu'
You have the option of setting one of the displayed languages
for the on-screen menu (OSD). However, the DVD recorder
display will only display English text regardless of this setting.
P The DVD recorder will insert the TV channel.
0 Repeat steps 7 to 9 until you have resorted/deleted all the TV
The language can also be set in the installation menu from the
GUIDE Plus+® system.
channels you want.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional installation features
a Time/date is displayed incorrectly despite manual setting
b With 'SMART CLOCK', time/date is transferred from the TV channel
saved on 'P01' and automatically corrected.
To activate the new language you must switch the
DVD-Recorder off and on again (button STANDBY m ).
You can either enter another TV channel for transferring the data or
disable the function.
In the line 'Clock preset' select the relevant TV channel with
D or C . To disable, select 'Off'.
5 Select the appropriate setting using B or A and confirm with
OK .
6 To end, press SYSTEM MENU .
9 Check the displayed settings and confirm with OK .
P 'Stored' will appear briefly on the screen.
Setting the time
0 To end, press SYSTEM MENU .
If the display shows an incorrect time or '--:--', the time and date must
be reset manually.
SMART CLOCK
Connection using a component video
(Y Pb Pr/YUV) cable (noprogressive
scan)
'SMART CLOCK' automatically sets the time and date using the information
transmitted by the TV channel. Normally the TV channel stored at
programme number 'P01' is used. In the 'Clock preset' line you can
select the programme number (channel name) whose TV channel transmits
this information.
Component video (Y Pb Pr) is the highest quality picture transmission
option. This is achieved by dividing the video signal into a luminance
signal (Y) and two colour difference signals - red minus luminance (V)
and blue minus luminance (U). As a rule, "Cr, Pr" or "R-Y" is used to
describe the red difference signal and "Cb, Pb" or "B-Y" the blue
difference signal.
These signals are transmitted through separate lines. The connectors of
this cable and the corresponding sockets are usually green (luminance,
Y), blue (U, Pb, Cb, B-Y), and red (V, Pr, Cr, R-Y).
If the time/date is not displayed correctly you need to choose the 'Off'
setting in the 'Clock preset' line and set the date and time manually.
1 Press the BROWSER HDD button and then the SYSTEM
MENU button on the remote control.
P The 'SYSTEM MENU' appears.
2 Select 'Set up' using B .
3 Press C to select 'System'.
Attention!
If you choose this type of connection, the DVD recorder must already
be connected and completely installed (initial installation complete).
Switching of the signal to the COMPONENT VIDEO OUT sockets is
carried out in a menu that is not yet available during the initial
installation.
4 Select the line 'Installation' using B and confirm with C .
P A message appears on the screen that this setting will flush the
'Time Shift Buffer'.
O If the 'Time Shift Buffer ' contains important recordings, save
them with the REC/OTR n button first. Read additional
information to the 'Time Shift Buffer' in the chapter 'The Time
Shift Buffer'.
Preparation:
•) The TV set is switched on, and, if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
5 Select 'Yes' with D and confirm with OK .
O If the message window was closed, confirm the line with
1 Press the DISC MENU and then the SYSTEM MENU button
C again.
on the remote control.
6 Select 'Time/Date' using B or A and confirm with C .
P The menu bar appears.
2 Select ' ' symbol with D or C .
A
Installation
Time/Date
Time
20:00
2003
01
Year
Month
Date
Clock preset
01
01
To exit press
SYSTEM MENU
7 Change the time in 'Time' using the number buttons 0..9 on your
remote control.
8 Check 'Year', 'Month' and 'Date' in the same way. Select the
entry field with the B or A button.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional installation features
3 Select the ' ' symbol using B or A and confirm with C .
t
7 Use a component video (Y Pb Pr) cable, connect the three cinch
sockets (red, blue, green) COMPONENT VIDEO OUT at the
back of the DVD recorder with the corresponding three
component video (interlaced) input sockets of your TV set, usually
labelled 'Component Video Input', 'YUV Input', 'YPbPr', 'YCbCr' or
simply 'YUV'.
Picture
TV shape
16:9
Off
Warning!
Black level shift
Video shift
Do not confuse these sockets with the five-component RGB
sockets (if available) or the yellow video (CVBS/FBAS) socket and
the two audio sockets (red/white). The five-component RGB
sockets are only provided for the R-G-B-H-V signals (red, green,
blue with horizontal and vertical synchronisation impulse).
ï
SCART video
RGB
Please observe the colour sequence
4 Select the line 'SCART video' using A or B and confirm with
The colours of the sockets at the DVD recorder and the connectors
must match those of the socket colours at the TV set
C .
(red-red/blue-blue/green-green). If they don't, the colours of the picture
may get mixed up or the picture may not be visible.
5 Select your setting with B or A . If the YPbPr output (YUV
signal) is switched on, S-video (Y/C) and video (FBAS/CVBS) signals
will not be transmitted simultaneously.
8 Use an audio (cinch) cable, connect the red/white cinch socket
AUDIO OUT L/R at the back of the DVD recorder with the
most coloured red/white audio input socket of your TV set
(usually labelled 'Audio in' or 'AV in'. See the instruction manual of
your TV set.)
The 'RGB' signal is switched off.
O 'S-video + YPbPr'
Component Video (YUV) and S-Video(Y/C).
GUIDE Plus+® menus only available on YUV ouput sockets.
O 'CVBS + YPbPr'
9 If necessary, switch your TV set to the component video
(Interlaced) input sockets. If there is a switch or selection on your
TV-set between 'Interlaced' and 'Progressive scan' select
'Interlaced'. 'Progressive scan' will be not supported from this
DVD-Recorder.
Component Video (YUV) and Video (FBAS/CVBS).
GUIDE Plus+® menus only available on YUV ouput sockets.
With all other settings, the signal is switched off at the
COMPONENT VIDEO OUT sockets. This will also be displayed
as information on the screen.
Also consult the instruction manual of your TV set.
P The menu of the DVD recorder should now appear on the TV
screen. If not, check the cable connections and the settings on
your TV set.
For more information on the other settings, read section 'Picture
settings' ('SCART video') in chapter 'User preferences'.
6 Confirm with OK .
O If necessary store this setting on your TV set.
0 End with SYSTEM MENU .
28
Download from Www.Somanuals.com. All Manuals Search And Download.
The GUIDE Plus+® System
Setting up the GUIDE Plus+® System
General information
Below we'll tell you how to set up the GUIDE Plus+® System to suit
your own particular needs and how to install the external receiver
(satellite receiver, .....) if you have one.
If the GUIDE Plus+® system has not been installed yet, the 'Setup'
screen will appear and you can start with the installation right now.
Your DVD Recorder is equipped with the GUIDE Plus+® System. The
GUIDE Plus+® System offers a free interactive electronic programme
guide that lists all the TV programmes available in your area. You can
also use the GUIDE Plus+® System to program your DVD recorder to
record your favourite shows.
1 Switch on the TV set. If required, select the programme number
Press GUIDE/TV to see a summary of all the TV programmes
currently being shown on the various TV channels. For the summary,
you can either display all shows for a particular start time or sorted
according to category.
for the DVD recorder.
2 Press the GUIDE/TV button on the remote control.
P The 'Grid' screen will appear.
If the GUIDE Plus+® system has not been installed yet, the
'Setup' screen will appear and you can start with the
installation right now.
For the GUIDE Plus+® System to operate correctly, it is necessary for
the DVD recorder to collect the necessary data. The DVD recorder
may take up to 24 hours to do this.
O If an 'Installlation-screen' appears, select the settings described
Please note the following:
in the next chapter and follow the instructions on the screen.
•) All the TV channels must already have been installed.
•) The TV channel that transmits the GUIDE Plus+® system information
must be installed.
If you did not find your country in this list, no TV channel will be
provided the GUIDE Plus+® system information.
further informations and tips.
3 Press A . Select the setting 'Setup' with C . This setting is
located on the second menu page.
Home
Setup your system to receive GUIDE Plus+ data.
Country/City
(Language)
Schedule Info
Editor
Setup
TV channel (aerial)
TV channel (SAT)
Eurosport
Astra 19.2E
Eurosport
Setup
View Demo
Deutschland
Eurosport
Österreich
Eurosport
Astra 19.2E, Hotbird
13.0E
Eurosport
Astra 19.2E
Eurosport
Schweiz (Deutsch)
United Kingdom
Eurosport
ITV
Astra 28.2E
4 Select one of the following options using B or A and confirm
France
España
Canal+
Tele 5
with OK .
Music Factory (TMF) /
Eurosport
TMF Astra 19.2E
Eurosp. Hotbird 13.0E
Music Factory (TMF)
Astra 19.2E
Music Factory (TMF)
Astra 19.2E
Music Factory (TMF)
Astra 19.2E
Music Factory (TMF)
Astra 19.2E
O 'Setup'
Nederland
Installation of the GUIDE Plus+® system.
Continue reading in the next chapter.
- Eindhoven
Music Factory (TMF)
Music Factory (TMF)
Music Factory (TMF)
Music Factory (TMF)
O 'View Demo'
- Rotterdam
- Amsterdam
België (Flemmish)
At this point you will be introduced to the functions of the
GUIDE Plus+® system. This will be done using stored demo
data.
If you start the demo, programmed recordings can be deleted.
By pressing OK during the presentation, you can proceed
directly to the installation of the GUIDE Plus+® system. Read
the next section.
•)The time and date must have been set.
•)The country and the local post code must have been set in
the GUIDE Plus+® system.
•)The aerial/cable network must be connected; it must be possible to
receive TV channels.
•)The DVD recorder must be connected to the mains
•)The DVD recorder must be switched to standby with the
STANDBY m button.
•) If you have connected an external receiver (satellite receiver, set-top
box, cable TV box,...), it must be switched on and tuned to the right TV
channel (see table above).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
The GUIDE Plus+® System
'Setup'
'External receiver 1'
O How you install the external receiver you will read in the next
Setup
Home
chapter.
Press Aor Bto select. Then press OK to confirm.
Setup
O If you have no external receiver connected, read the section
Choose item to set up :
Language
'Finalise set-up'.
English
Country
Postal code
External receiver 1
United Kingdom
XXXXX
None
External receiver 2
External receiver 3
None
None
Installation of the 'External receiver 1'
Setup
Home
Press Aor Bto select. Then press OK to confirm.
Setup
Choose item to set up :
Language
English
Check the data displayed on the screen. If necessary, you can change
these. To do so, select the corresponding line with B or A .
Country
Postal code
External receiver 1
United Kingdom
XXXXX
None
External receiver 2
External receiver 3
None
None
'Language'
Here you can change the language for the on-screen menu.
1 Press OK .
2 Select the desired language using B or A and confirm with
OK .
If you have connected an external receiver (satellite receiver, set-top
box, cable TV box), you must also install it in the GUIDE Plus+®
system. TV programmes (TV channels) that you can only watch via the
receiver can also be displayed in the GUIDE Plus+® system and be
programmed for recording.
3 Press OK to return to the 'Setup' screen.
'Country'
You can connect up to three external receivers to the DVD-Recorder.
Select the country you currently live from the list. The DVD recorder
needs this information to load the right channel list.
1 Select with B or A in the 'Setup'screen the line 'External
receiver 1' and confirm with OK .
1 Press OK .
2 Read the information on the screen and confirm with OK .
2 Select the country you live in using B or A and confirm with
OK .
3 Select the type of the external receiver. This setting serves to
preselect the type used.
3 Press OK to return to the 'Setup' screen.
Which types can I choose?
This selection depends on the country and the GUIDE Plus+® system
provider. Therefore, some types may have no function.
'Postal code'
In order to adjust the GUIDE Plus+® system correctly, it is necessary
to know your current location with the TV channels available. Using
the local post code and the country, the DVD recorder can
automatically make the settings.
'Cable': Cable receiver, cable box.
'Satellite': Analogue or digital satellite receiver.
'Terrestrial': Digital terrestrial decoder box.
'None': No external device connected.
1 Press OK .
4 Confirm with OK .
2 Choose the entry position using C , D . Select the local post
code of your location using A , B , or the number buttons
0..9 .
If you selected 'None', there is nothing further you need to do
here. Read on in the section entitled 'Continue set-up'.
Otherwise, you should continue here.
O Depending on the country you select, you can also enter
letters using B or A .
5 Select your provider from the list.
O If you do not have a provider, select 'No provider'
a I cannot enter a local post code
b You have selected a country in which none of the channels transmits
GUIDE Plus+® data yet.
6 Confirm with OK .
7 Select the brand of your external receiver from the list. If,
additionally your provider is printed on your receiver (e.g. Sky,...),
you must choose the provider as brand.
3 Confirm the local post code with OK .
4 Press OK to return to the 'Setup' screen.
O Depending on the type and provider you selected, a limited
selection will appear.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
The GUIDE Plus+® System
O Browse through the pages of the list using O , N .
Connecting G LINK™ transmitter
a My brand is not included in the list
b Select 'Satellite' and as provider 'No provider'.
You will see a list of all stored brands.
b If you do not find your brand, please proceed as follows:
- Select 'None'. You will find this setting at the end of the list.
- Tune your external receiver to the TV channel which transmits the
GUIDE Plus+® data (see table in the section 'General information'). If
this TV channel is available at the internal tuner of the DVD-recorder,
select this channel.
- Wait till the GUIDE Plus+® data is loaded (24 hours) and search for
your brand again.
The control data of the external receivers are automatically updated
(completed) via the GUIDE Plus+® system in few weeks. This is done
through the aerial, the cable, or the external receiver. You do not need
to bring the device to a service centre.
The external receiver (satellite receiver, set-top box, cable TV box) is
controlled via the DVD recorder with the G-LINK cable (supplied).
This means you can record TV shows that are received only through
the external receiver.
Connection of the G-LINK cable enables the GUIDE Plus+® system to
show the correct guide listing.
1 Connect the G-LINK cable to the G-LINK socket at the back of
the DVD recorder.
- If your brand is still missing, note the type and manufacturer of your
external receiver and call the customer support service in your country.
You will find the telephone number on the back of this instruction
manual.
8 Press OK .
2 Position the G-LINK transmitter in front of the external receiver
so that the control signal (IR signal) can be transmitted and
received by the receiver unhindered.
9 Select the input socket of the DVD recorder to which the receiver
is connected.
a My external receiver is connected only via aerial cable
- Press O to move to the next page.
Confirm 'Antenna (RF lead)' using OK .
- Enter the channel number under which the external receiver is stored
in the DVD recorder. (e.g.: channel number 'P 04'). Use the number
buttons 0..9 , or B , A , D , C .
If the external receiver is not allocated to a channel number, you must
search and store it in the DVD recorder as if it were a new TV
channel. Read section 'Search TV channels manually'. Please make
sure that the receiver remains switched on during search and, if
necessary, switch it on to a 'test signal'.
How do I find the right position?
If the position of the remote (IR) receiver is indicated on your external
receiver (IR, remote sensor, or such like), place the transmitter about 1
to 10 cm in front of it.
If the position is not indicated, proceed as follows:
- Switch off the external receiver.
0 Confirm with OK .
- Point the remote control at the front of the external receiver.
- Move the remote control slowly along the front while repeatedly
pressing the on/off button.
- When the external receiver switches on or off, you've found the
receiver.
- Attach the G-LINK transmitter about one to 10 cm in front of it.
3 Switch the receiver on and select programme number 02 on the
receiver or using its remote control.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
The GUIDE Plus+® System
a My external receiver does not display the programme
number
Finalise set up
During installation, the external receiver will be switched to a
different programme number. If the receiver does not display the
programme number, you must check the 'Video window' (left top
corner in the GUIDE Plus+® system) to see whether switching has
taken place.
Setup
Home
Press Aor Bto select. Then press OK to confirm.
Setup
- Select on the DVD-Recorder the socket where the receiver is connected
using CHANNEL q , CHANNEL r (e.g. EXT2for EXT2
AUX-I/O )
Choose item to set up :
Language
Country
Postal code
External receiver 1
English
United Kingdom
XXXXX
None
- Please check the TV show in the 'Video window' in the left top corner
of the screen.
External receiver 2
External receiver 3
None
None
- Check whether the picture changes during the next step ( OK button).
4 Read the information on the screen carefully.
Confirm with OK .
P The DVD recorder will now attempt to use the G-Link
connection on the external receiver to select a different
programme number (e.g.12). This programme number
depends on your external receiver.
1 Check the settings shown on the screen.
If the settings are not correct, choose the line in which you want
to change the settings and confirm with OK .
2 Press the green function button to leave the screen.
5 Has the external receiver been switched to the programme
number displayed on the screen?
O If you want to view a demonstration of the GUIDE Plus+®
system select 'View Demo' with B and confirm with OK .
If you start the demo, programmed recordings can be deleted.
If this is the case, select 'YES'.
If no switching has taken place, select 'NO'.
a My external receiver has not switched to the other
programme number.
- Check that the external receiver is connected and switched on.
O If you do not want to see the demonstration of the GUIDE
Plus+® system, end using GUIDE/TV .
- Check the connection and position of the G-LINK transmitter.
- For another attempt with a new code of the chosen brand, select 'NO'.
- Confirm with OK on the remote control.
3 This completes the set-up process for the GUIDE Plus+® system.
4 Switch the DVD-recorder to the TV channel which transmits the
GUIDE Plus+® data. The right TV-channel for your country you
will in the table in the chapter 'The GUIDE Plus+® system' in the
section 'General information'.
- If the receiver has not switched yet, select 'NO' again and confirm with
OK . It may take several attempts for a receiver brand.
If you return to the setup screen after confirming 'NO', your receiver
may not have been installed. Check the connections again.
Leave the DVD recorder switched on during the night to load the
GUIDE Plus+® data.
The information will be available in the next 24 hours.
- Tune your external receiver to the TV channel which transmits the
GUIDE Plus+® data (see table in the section 'General information'). If
this TV channel is available at the internal tuner of the DVD-recorder,
select this channel.
- Wait till the GUIDE Plus+® data is loaded (24 hours) and try the
switch over again.
The control data of the external receivers are automatically updated
(completed) via the GUIDE Plus+® system. This is done through the
aerial, the cable, or the external receiver. You do not need to bring the
device to a service centre.
5 If data are available check in the 'Editor' screen that the TV
channel which transmits the GUIDE Plus+® data is allocated to the
right programme number. Change the programme number if
necessary.
- If your receiver still does not switch, note the type and manufacturer of
your external receiver and call the customer support service in your
country. You will find the telephone number on the back of this
instruction manual.
6 Your external receiver has now been installed.
7 Press OK to return to the setup overview.
a I want to install additional external receivers
When installing additional external receivers, please observe the
following: The external receiver which is controlled by the G-LINK
transmitter must be below the other additional receivers. The
IR(infrared) remote control signal is reflected diagonally upwards and
can therefore be used to control additional external receivers which
are on top.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
The GUIDE Plus+® System
Using the GUIDE Plus+ ® System
General
What must I pay attention to when installing an external
receiver for the first time?
•) The receiver must be switched on.
•) If you can switch between 'TV' and 'Radio' on the receiver, select 'TV'.
•) Select the TV channel that transmits the GUIDE Plus+® data on the
receiver. You will find the corresponding TV channel for your country in
the table in section 'General Information' in chapter 'The GUIDE Plus+
System'.
The GUIDE Plus+® System provides you with a free on-screen listing
for all the TV channels in your location. You can also use it to control a
connected external receiver (satellite receiver, set top box, cable box).
•) On the DVD recorder, select the programme number of the input
socket to which the external receiver is connected:
'EXT2' Scart socket at the back of the DVD recorder EXT2
AUX-I/O
'EXT1' Scart socket at the back of the DVD recorder EXT1 TO
TV-I/O
The information of the GUIDE Plus+® System is divided in six screen
components:
•) Function buttons (colour panels) along the top of the screen. These
correspond to the colour buttons of the remote control
•) The video window
•) Programme information or instructions for use
•) A line for the selection of available GUIDE Plus+® menus
•) The channel guide with the current listings
•) If the external receiver is only connected to the aerial socket, you
must select the programme number on the DVD recorder under which
the external receiver is stored.
•) Advertising information or instructions on the GUIDE Plus+® system
Calling up the GUIDE Plus+ ® System:
Press GUIDE/TV on the remote control.
•) The DVD recorder must be switched on.
•) If GUIDE Plus+® data were loaded, switch the DVD-Recorder off with
the STANDBY m button for approx.10 minutes. During this time,
the data will be stored in a memory to prevent them from being erased
in case of malfunction (power failure).
Closing the GUIDE Plus+ ® System:
•) Press GUIDE/TV to leave the GUIDE Plus+® System and continue
viewing the program you were viewing before you called up the GUIDE
Plus+® System.
You must observe this information only when installing the receiver for
the first time. At this point, there is no GUIDE Plus+® data available yet
in order to automatically detect the TV channel that delivers the GUIDE
Plus+® data.
Using the buttons on the front of the DVD recorder
Calling up the GUIDE Plus+® System: GUIDE button.
Closing the GUIDE Plus+® System: GUIDE button.
Confirm the function: OK button.
Red function button: n button.
Cursor buttons: UP , DOWN , LEFT , RIGHT .
®
The navigation in the GUIDE Plus+ System
Press GUIDE/TV to view the main menu. Press A to select the
menu line. You can select one of the following functions with D or
C . Press at the desired function the B button for confirmation.
O 'Grid':
Standard GUIDE Plus+® system screen (programme guide)
O 'Search'
TV shows sorted by category (movies, sport, etc.)
O 'Schedule':
Scheduled (pre-programmed) recordings
O 'Info':
Additional special functions in the GUIDE Plus+® system.
O 'Editor':
Display/Change the channel settings for the 'Grid' screen
O 'Setup':
For changing the basic settings. Read further information in the
chapter 'Set up the GUIDE Plus+® System'.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
The GUIDE Plus+® System
3 Use the D or C button to select the show you want.
Function buttons (colour buttons)
If GUIDE Plus+® information has been loaded, function buttons (colour
fields) at the top of the screen indicate that you can perform various
actions in the GUIDE Plus+® screen. Red, Green, Yellow, Blue whose
function depends on the respective menu. Always check the function
(description) in the corresponding colour field before pressing a
button.
O You can hold down D or C to browse faster through the
start times.
O If you press the button N or O , you can switch forward
or back a day.
If no colour buttons are displayed, pressing them will have no effect.
I want to call the additional information/advertisement on
the left hand side of the screen
INFO button
An INFO button is also available. If additional information is available
(symbol i on the screen), you can use this button to retrieve the
information.
Press D in the line of the TV channel repeatedly, until the additional
information/advertisement on the left hand side of the screen is
highlighted. You can toggle between the two sets of information using
B , A .
You can exit these areas with C or with the blue function button.
The 'Grid' screen
Function buttons (colour buttons ) in the 'Grid' screen
You can use the colour buttons on the remote control to select the
following:
'Record' (red button):
The highlighted show will be programmed for automatic recording. It
appears in the 'Schedule' screen.
You can store up to 12 TV shows for recording.
'Home' (blue button):
Return to the current time in the listing ('Grid' screen).
This list appears when you press the GUIDE/TV button. You can view
the current listing for all the TV channels from today to the same day
next week.
ATTENTION!
If data from the GUIDE Plus+® system is already available after the
initial installation, check the allocation of programme numbers to the
channels in the 'Editor' screen.
Read therefore the section 'The 'Editor' screen'.
If the TV-channel that transmits the GUIDE Plus+® data was allocated
to the wrong programme number, no further GUIDE Plus+® data can
be loaded.
1 Press GUIDE/TV . The 'Grid' screen will appear.
P In the top left corner the picture of the TV channel appears
which was selected before you call up the GUIDE Plus+®
system.
2 Select the TV channel you require with A or B .
O You can use the number buttons 0..9 to select a TV channel
directly.
O You can use the CHANNEL q and CHANNEL r buttons
to scroll a page at a time.
Choosing a TV channel from a listing
- Press the yellow function button.
- An overview of all TV channels appears.
- Select the TV channel you want using C , D , B , A .
- Confirm with OK .
34
Download from Www.Somanuals.com. All Manuals Search And Download.
The GUIDE Plus+® System
The 'Schedule' screen
The 'Search' screen
Frequency VPS/PDC Home
, Single recording
Home
Search displays programme listings by categories of
interest. Press Bto use. Press Dfor Grid. Press Cfor
Schedule
Grid
/Record
21-Oct 20:00 21:30 BBC1
Search
Schedule Info
Search
Schedule Info
Movies
All
Editor
Sport
Freq. Timing
Once +0
Action
21-Oct Matrix
Once
0
Animation
Comedy
Drama
Romance
Sci Fi
Thriller
This menu displays the shows that are set to record. You can clear
recordings or make changes using the function buttons. Moreover, you
can manually program recordings.
This menu lets you access show listings organised by category. This is
an even easier way of searching the show you want to watch.
Make your selection from a general category (Movies, Sport, Children's,
Series, etc.) and a detailed category (Adventure, Comedy, Drama, etc.)
Depending of the type of programming a recording appears:
Programming from the 'Grid' screen:
'21-Oct: Day and month of the recording
'Matrix': Title of the show (if it is transmitted)
Colours of the categories:
Purple-Movies
Green-Sport,
Blue-Children's,
Teal-Others,
The Sort service gives you show listings for the next 7 days.
Programming from the 'Schedule' screen:
'21-Oct': Day and month of the recording
'20:00': Start time
'21:30': Stop time
'BBC1': TV channel
1 Select the category with D , C .
Confirm with B . Select the minor category with B , D , C .
Additionally appears to each programmed recording:
'Freq.':
2 Confirm with OK
Frequency 'Once'..once/'M-F'..daily (Monday to Friday)/'Mon'..weekly
(every week on the same day, e.g. Monday)
'Timing': In case an extended switch-off time has been entered or
'VPS/PDC' (V-P) is switched on.
3 Use the B , A , D , C buttons to scroll through the shows.
a 'No Program was found' appears on the screen
There is no TV show today that matches the selected category.
- Select a different day with C , D .
- Press A to return to the 'Search' screen.
Function buttons (colour buttons ) in the 'Schedule'
screen
Function buttons (colour buttons ) in the 'Search'
You can select between programming with ShowView® (red button) or
manual programming (green button).
screen
If you have highlighted a show you can use the coloured buttons to
perform the following actions:
If you selected an already programmed TV show, you can make
changes using the colour buttons of the remote control.
The function of the colour buttons will change depending on the tile
you select. Always check the function (description) in the
corresponding colour field before pressing a button.
'Record' (red button):
The highlighted show will be programmed for recording. It appears in
the 'Schedule' screen.
1 Press B .
'Home' (blue button):
Select the corresponding recording with B , A .
Return to the current time in the listing ('Grid' screen).
2 Select the corresponding tile with D , C .
left tile
red button: clear the recording
green button: change the data
center tile
yellow button: change the TV channel
right tile
green button: repeat
yellow button: extend switch-off time, switch VPS/PDC on/off
35
Download from Www.Somanuals.com. All Manuals Search And Download.
The GUIDE Plus+® System
1 Select the TV channel you want to change using B , A .
The 'Info' screen
2 Press the green function button.
This screen can be divided in subcategories. These depend on the
information provided by the GUIDE Plus+® system. If there are no
categories available, no data has been provided yet. Try visiting this
page later.
3 Enter the programme number of the TV channel using the number
buttons 0..9 . You can only enter programme numbers of TV
channels that have already been installed.
Entering the TV-channel of an external receiver
1 Press B .
- Select the TV channel you want to watch only through the external
receiver using B , A .
Select the corresponding subcategory with B , A .
2 Select from the displayed data with B or A .
- Choose the corresponding source using the red function button.
This function button is only available when at least one external
receiver has been installed. Read section 'Setting up the GUIDE Plus+®
system' on how to install an external receiver.
3 Confirm using OK to receive more information.
4 Return to the 'Info' screen by pressing the red function button
- Press the green function button. Enter the programme number of the
TV channel which you would also enter for this TV channel on the
external receiver.
('Info').
The 'Editor' screen
Please observe that in the case of modified TV channels, the transfer of
GUIDE Plus+® channel data may take up to 24 hours.
Home
Editor displays your TV channel settings. You may
switch channel On or Off (grey), select their Source
and their programme number. Press Bto use. Press
Dfor Info. Press Cfor Setup.
The 'Setup' screen
Search
Name
BBC1
BBC2
ITV
Schedule Info
Editor
On/Off Source Programme N.
On TV
On TV
On TV
On TV
P001
P002
P003
P004
Home
Setup your system to receive GUIDE Plus+ data.
CH4
Schedule Info
Editor
Setup
Setup
View Demo
Here you can allocate the programme numbers to the corresponding
TV channels and switch them on/off for the programme listings ('Grid'
screen). Moreover, you can define the use of the TV channels on the
external receiver.
Here you can make or change the basic settings such as language,
country, external receiver. Moreover, you can watch an automatic
demonstration of the GUIDE Plus+® system.
1 Press B .
2 Select the TV channel you want to change using B , A .
O Use the D and C buttons to switch between tiles.
'Setup'
All the settings you have already made are displayed here. Select the
desired line using B or A and confirm with OK . For more
information on the settings, read section 'Setting up the GUIDE Plus+®
system' in chapter 'The GUIDE Plus+® system'.
left tile
This tile contains the TV channels with their short descriptions and
indicates whether the TV channel is displayed in the programme listing
('Grid' screen) or not.
O You can switch on/off a TV channel for the 'Grid' screen using
'View Demo'
the red function buttonn
Here you can view a demonstration of the different functions of the
GUIDE Plus+® system.
Start the automatic presentation with OK .
If you start the demonstration, programmed recordings can be deleted.
If you cancel the presentation by pressing OK , you will go directly to
the setup menu.
right tile
This tile contains the TV channel properties and the programme
numbers. You can modify channel allocation or assign an external
receiver. In order to assign a receiver, it must be already installed in
the GUIDE Plus+® system.
To change allocations, proceed as follows:
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on the HDD
General
The Time shift Buffer
As soon as you turn on the DVD recorder, the currently selected TV
channel on the DVD-Recorder is recorded in a temporary storage
(Time shift Buffer).
Recordings in the time shift buffer will be automatically deleted e.g.
after 3 hours if the period of the time shift buffer is set to 3 hours
(factory setting). Only recordings marked in the Time shift Buffer will
be stored on the the built-in HDD For more information, read the
next section 'The Time Shift Buffer'.
The following additional information is stored with each recording:
•) name of the recording
If no name is recognised from the GUIDE Plus+® systems data, only the
programme number (programme name) and the time will be stored as
the name.
As a result of the high data transfer speed of the HDD, it is possible to
play back recordings from the time shift buffer while the recording is
still in process.
Therefore, you can jump back to the currently selected TV programme
using JUMP BACK and watch a scene again.
•) length of the recording
•) recording mode (quality)
•) date of the recording
•) index picture of the recording
Moreover, you can use all playback features such as still picture, slow
motion, search by time, search with N , O even with recordings
that are still in the time shift buffer.
In the meantime, the recording continues.
To facilitate the search of a specific position, a chapter marker is
recorded every 5 minutes. How you switch off this function you will
read in chapter 'User preferences for the HDD' in the section
'Preferences', 'Recording', 'Chapters'. After the recording is
completed, you can select these markers with N , O . Please
make sure that the chapter selection is activated (the 'CHAPTER'
symbol lights up in the info bar at the top of the screen). If necessary,
you can activate it using T/C .
If you change the TV channel on the DVD-Recorder ( CHANNEL q ,
CHANNEL r ) a new title is created with the new TV channel in the
time shift buffer. If you watch a TV show only for a short time (less
than 60 seconds) before you change to a different TV channel, no new
title is created.
For easier navigation, you can change the time period of the time shift
buffer from 1 to 6 hours. 1 hour means that a recording is available
only for one hour before it is automatically deleted to make room for
the current recording.
If the GUIDE Plus+® system delivers title information, the latter is also
stored with the recording. When recording TV shows without GUIDE
Plus+® information, only the date and the time of the recording are
stored as title.
What is the advantage from 1 hour and 6 hours?
The complete time periode of the time will be displayed on the whole screen
of your TV.
With 1 hour you will get the highest comfort for searching a specific scene.
With 6 hours you will get the highest possible recording time.
Please observe that the Time shift Buffer needs also storage capacity on the
HDD. Depending of the selected record mode (picture quality):
6 hours in 'M1' = approx. 28GB
6 hours in 'M8' = approx. 3,4GB
How you enter the time periode, read in the chapter 'User preferences for
the HDD' in the section 'Preferences' / 'Recording'/ 'HDD buffer'.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on the HDD
O Red function button:
Symbols in the 'Time Shift Buffer'
Following symbols can appear in the info bar at the top of the screen in
the 'Time Shift Buffer'. With the INFO button on the remote control
you can also call up this infobar.
- To cancel the marked recording that was set with the
REC/OTR n button.
- Hold button down to stop the recording at the actual
position.
O Yellow function button: ('OVERVIEW')
Left area
To display an overview of all content of the time shift buffer.
Information about the input signal were displayed here:
'C' Actual TV show (live picture) from the selected TV channel
O Blue function button:('MORE INFO'):
To display any additional information for the actual TV show
transmitted by the GUIDE Plus+® system.
'P01' Programme/Channel number of the selected TV channel
'ARD' Name of the TV-channel
'D' Playback from the HDD
Mark TV shows for recording
As a rule, recordings in the time shift butter are automatically deleted
after a certain time (1 to 6 hours). In order to store recordings on the
HDD permanently, you can mark sections of the time shift buffer that
will not be deleted and will be available as titles for later playback.
Right area
Information about the current operating status were displayed here:
'B 16:03:02' Actual (live) picture of the selected TV-channel
( TUNER button)
'J PLAY' Playback from the HDD
'M PAUSE' Still picture
'H 1/2X' Slow motion forwards
'G -1/2X' Slow motion backwards
'L 4X' Fast motion forwards
'K -4X' Fast motion backwards
Mark an entire title
A title marker is set if you are watching a TV show longer than 60
seconds. (No change of programme number within 60 seconds)
If you want to mark an entire title (title marker at the beginning and at
the end), proceed as follows:
1 Press INFO to display the bar of the time shift buffer on the
Navigation in the time shift buffer
screen.
Preparation:
O You can also press the yellow colour button to get a better
•) The TV set is switched on, and, if necessary, the programme number for the
DVD recorder has been selected.
overview of the recordings.
•) the DVD recorder is switched to tuner mode (button TUNER ).
2 Select the title you want to store with B , A .
1 Press INFO to display the bar of the time shift buffer on the
3 Press REC/OTR n to mark the title.
P The colour within the bar changes to red. If you press the
yellow button, you will see programmes marked for recording
with a red dot.
screen.
2 The following buttons are available:
O
N , O , PLAY G , PAUSE 9 , D , C , JUMP
FWD , JUMP BACK for navigation in the time bar.
O To remove the marker, press the red function button. The
red title marker disappears.
O
T/C
Switching between title/chapter for selection using N ,
O . The top screen line displays either 'TITLE' for selecting
titles or 'CHAPTER' for selecting chapters
4 If you want to mark other titles, repeat steps 2 and 3 , until
you have selected all the titles you want.
O If you want to mark several titles in a sequence, go to the
O
REC/OTR n :
oldest title and press REC/OTR n several times.
- To start a recording that will be stored on the HDD.
- To mark a title that will be stored on the HDD.
- Hold button down to start the recording from the actual
position.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on the HDD
O Using REC/OTR n you can also mark the future end of a
title (actual TV-show is not over yet) You will see this in the
red marked 'O' symbol on the right end of the Time Shift
Buffer bar.
'Auto delete'
If there is no space for new recordings on the HDD, recordings will be
automatically deleted in the following order:
1) Titles that have already been viewed. Symbol 'E'.
2) Titles that were not protected. No symbol 'F' available.
The recording will be stoped automatically at the end of the
program.
If the start (titlemarker) of the TV-Show was not taken from
the GUIDE Plus+® System, or no GUIDE Plus+® is available,
you can extend the end by +30, +60, +90 ,... minutes using
REC/OTR n .
More information you will find in the chapter 'User preferences for the
HDD'.
Manual recordings
Mark part of a title
Recordings from the actual on the DVD-Recroder selected TV channel
are always started and recorded in the time shift buffer as soon as you
switch on the device. To store recordings on the HDD, choose from
the following:
You can also mark only parts of a title.
If you mark several parts of a title, each part will be stored as a
separate title on the HDD.
Start of the recording:
1 Press INFO to display the bar of the time shift buffer on the
screen.
O Start the recording from the begin of the TV-show (Start is
known from the GUIDE Plus+® System, or change orf the TV
program)
O You can also press the yellow colour button to get a better
overview of the recordings.
Press REC/OTR n .
2 Select the title you want to store with B , A .
O Start the recording from the actual position (from now)
Hold REC/OTR n pressed, until the red light around the
n button on the front is switched on.
3 The following options are available:
O Freely selectable end:
- Press REC/OTR n to select the entire title. The colour
changes to red.
Stop the recording in progress:
- Search for the desired end using D , C .
- Hold down the red button:
Red marked recording changes to its original colour from
the current position to the end of the title.
O Stop the recording automatically:
If the start of the TV show is known from the GUIDE Plus+®
System
The recording will stop at the end of the TV-Show.
If you want to set more markers in one title, start marking at
the begin of the title.
O Stop the recording manually:
Hold the red button on the remote control pressed, until the
red light around the n button on the front is switched off.
O Freely selectable beginning:
- Search for the desired beginning using D , C .
- Hold down the REC/OTR n button.
The marker changes to red from the current position to the
end of the title.
-You can mark a recording for storage on the HDD using
REC/OTR n on the remote control or n on the device. Such
marked recordings are displayed as a red bar in the time shift
buffer and are not automatically deleted after the time shift buffer
period (1 to 6 hours) expires.
O Freely selectable beginning and end:
First, you must define the beginning and then cut off the end.
- Search for the desired beginning using D , C .
- Hold down the REC/OTR n button.
The marker changes to red from the current position to the
end of the title.
-If you switch off the DVD recorder with STANDBY m or
select the 'Flush Buffer' function, all other recordings of the
time shift buffer will be deleted.
- Search for the desired end using D , C .
- Hold down the red button:
Red marker changes to its original colour from the current
position to the end of the title.
OTR recordings
Recordings made using REC/OTR n will be automatically stopped
after the end of the TV show if information is available from the
GUIDE Plus+® system. If no information is available, you can select the
time after which a recording will automatically stop using
REC/OTR n . (each time you press the button, you prolong the
switch-off time by 30 minutes)
How can I delete the changes?
Press REC/OTR n to mark the entire title.
To remove the marker, press the red function button.
If you press the red function button, the marker for the recording is
removed.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on the HDD
Direct Record
Automatic recording from a satellite
receiver (sat recording)
If the recording is manually started, the switched off DVD recorder
receives the currently selected TV channel through the scart cable. The
selected TV channel is compared with the stored TV channel of the
DVD recorder. If the TV channel can be found, the DVD recorder
selects it and starts the recording.
You can use this function if you have a satellite receiver that can
control other devices via a scart cable and has a programming function
(timer). For more information, consult the instruction manual of your
satellite receiver.
If no corresponding TV channel is found in the DVD recorder, an error
message appears.
Read the next section 'Switching Direct Record on or off' on how to
switch Direct Record on or off.
1 Switch on the TV set. If necessary, select the programme number
for the DVD recorder.
How does Direct Record work?
2 Press the BROWSER HDD and then the SYSTEM
MENU button on the remote control.
The DVD recorder compares the TV channel selected on the TV set with its
stored TV channels via the scart cable. If the same TV channel is found, the
DVD recorder switches to the corresponding programme number and starts
recording.
P The 'SYSTEM MENU' appears.
3 Select 'Preferences' with B .
Please do not change channel on the TV set during search. This may affect
the tuning on the DVD recorder.
4 Press C to select 'Recording'.
1 Select the programme number on the TV set from which you want
5 Select 'Sat record' (second menu page) using B .
to make the recording.
6 Select 'On' using C .
2 Press REC/OTR n while the DVD recorder is switched off .
a 'WAIT' appears in the display
O To switch off the function, select 'Off' using C .
b The DVD recorder compares its stored TV channels with those of the TV
set. Please do not change channel on the TV set while 'WAIT' appears in
the display.
7 To end, press SYSTEM MENU .
8 Connect the EXT2 AUX-I/O scart socket of the DVD recorder
with the corresponding scart socket of the satellite receiver using a
scart cable.
a 'NOTV' appears on the display
b This TV channel was not found in the memory of the DVD recorder.
Check whether all TV channels stored in the TV set are available on the
DVD recorder. If necessary, store the missing TV channels. Read section
'Manual TV channel search' in the chapter 'Installing your DVD recorder'.
b Check the connectors of the scart cable.
9 Program the satellite receiver with the desired data for recording
(programme number of the TV channel, start time and end time).
If necessary, also consult the instruction manual of your satellite
receiver.
b Consult the instruction manual of your TV set to find out which scart
socket sends out video signals.
b If all this is to no avail, you cannot use this function.
0 Switch off the DVD recorder using STANDBY m .
P In addition, 'SAT' will appear in the display to indicate that the
function is activated.
3 To stop the recording press and hold the red function button on
the remote control until the red light around the n button is
switched off.
A If necessary switch the satellite receiver to standby. See the
instruction manual for the satellite receiver for details.
The DVD recorder is now ready for recording.
P The start and the end of the recording will be controlled via
the EXT2 AUX-I/O scart socket.
Switching 'Direct Record' on or off
1 Press BROWSER HDD and then SYSTEM MENU button on
the remote control.
P The 'SYSTEM MENU' appears.
2 Select 'Preferences' with B .
3 Press C to select 'Recording'.
4 Select 'Direct rec.'(second menu page) using B .
5 Select 'On' using C .
O To switch off the function, select 'Off' using C .
6 End with SYSTEM MENU .
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on the HDD
Recording from a camera connected to
the front sockets
Recording from a video recorder/DVD
player
Using this function, you can store recordings via the front sockets
directly on the HDD. These titles will be automatically protected to
prevent them from being automatically deleted in case the HDD is full.
The symbol 'F' indicates such a protection.
Please observe:
Most pre-recorded video cassettes or DVDs are copy-protected. If you
try to copy these, the message 'COPY PROT' will appear in the display
of the DVD recorder.
You can edit these recordings on the HDD and transfer (archive) them
later on a DVD+RW/+R disc. How you archive recordings on a
DVD+RW/+R you will read in the chapter 'Recording on a
DVD+RW/+R' in the section 'Archiving (storing) titles on a
DVD+RW/+R'.
Preparation:
•) Switch on the TV set and, if necessary, select the programme number for the
DVD recorder.
•)Switch on the DVD recorder.
•) Select recording mode (button TUNER , button SYSTEM MENU ,
'Preferences', button C 'Recordmode ').
Please observe the following:
•) Any programmed recordings (TIMER) will not be carried out during
this operating mode.
1 Connect the video recorder/DVD Player as described in the
chapter 'Connecting additional devices'.
•) If there are any recordings in the time shift buffer, they will be
deleted. Therefore, store important recordings on the HDD
( REC/OTR n ). For more information on the time shift buffer, read
the chapter 'The Time Shift Buffer'.
2 Press TUNER to display the picture of the Video recorder/DVD
player on the screen.
3 Use CHANNEL r , CHANNEL q to select the programme
number of the input socket to which the Video recorder/DVD
player is connected. ('EXT1' for EXT1 TO TV-I/O , 'EXT2' for
EXT2 AUX-I/O )
1 Connect the camera as described in the chapter ' Connecting
additonal devices/Connect camcorder to the front sockets'
2 Press CAM on the remote control.
Please observe that for recordings via the front sockets S-VIDEO
(CAM1) / VIDEO (CAM1) /'CAM1' or DV IN (CAM2) / 'CAM2'
the recording mode must be selected under 'Camera mode' in
'Preferences' of the system menu.
P The DVD recorder will switch to camera mode.
4 Switch on the video recorder/DVD player.
O In case playback has started automatically, interrupt it with
STOP h or PAUSE 9 .
5 Start recording by pressing REC/OTR n on the DVD recorder
and playback by pressing PLAY G on the video recorder/DVD
player.
3 Select the socket to which the camera is connected using CAM .
O 'CAM1'
a When copying video cassettes, 'NO SIGNAL' appears in the
display of the DVD recorder
b Check whether the cable connectors are properly inserted.
b If the recording is made from a video recorder, change the 'tracking'
setting on the video recorder.
For recordings from the VIDEO (CAM1) , S-VIDEO
(CAM1) sockets.
Switching between the two sockets is done automatically. If a
signal is available at both sockets at the same time, the signal at
the S-VIDEO (CAM1) socket has priority. If you change
socket (unplug), you must re-select the socket using
CAM (press twice).
b In case of bad or non-standard video input signals, the DVD recorder
may be unable to detect the signal.
a When copying DVD video discs or pre-recorded video
cassettes, the picture is fuzzy and brightness varies
b This happens when you try to copy DVDs or video cassettes that are
copy-protected. Although the complete cassette/disc is recorded, only
parts without copy protected signal can be played back. This
interference is unavoidable with copy-protected DVDs or video
cassettes.
O 'CAM2'
For recordings from the DV IN (CAM2) socket.
4 Press REC/OTR n to start the recording.
P If no signal is available, no recording will be made or the
recording in progress will be stopped.
P During the playback of a recorded 'copy protected' signal you
will see only that parts of the recording where no copy
protection can be recognised.
6 To stop the recording press and hold the red function button on
the remote control until the red light around the n button is
switched off.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on the HDD
5 You can stop the recording using the following buttons:
O
PAUSE 9
The recording will be paused. If you press the button again,
the recording will resume.
A new chapter is created.
O
STOP h
The recording will be interrupted. You can start a new
recording by pressing REC/OTR n .
A new title is created.
6 Press the red function button to terminate the camera operating
mode.
P The recording will be stored on the HDD as a new title.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming a recording (TIMER)
General
Programming recordings with the
GUIDE Plus+® System
Use 'Programming a recording (TIMER)', to automatically start and stop
a recording at a later date.
The DVD recorder will switch to the right programme number and
begin recording at the correct time.
On this DVD recorder you can pre-programme up to 12 recordings
within a period of one month.
The GUIDE Plus+® System has made it even easier to programme
recordings. All you have to do is select the show you want to record
from a channel listing.
To make a programmed recording, your DVD recorder needs to
know:
* the date you want to make the recording
* the programme number of the TV channel
* the start and stop time of the recording
* VPS or PDC on or off
Preparation:
•) The TV set is switched on, and, if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
1 Press GUIDE/TV on the remote control.
This information is saved in a 'TIMER block'.
Before you begin, make sure the clock is set. If the clock is not set, the
'Time/Date' menu will appear when you press the TIMER s button.
What is 'VPS/PDC'?
- 'VPS' (Video Programming System)/'PDC' (Programme Delivery Control)
are used to control the start and duration of TV channel recordings. If
a TV programme starts earlier or ends later than was scheduled, the
DVD recorder will then turn on and off at the correct time.
What do I need to know about 'VPS/PDC'?
- Usually the start time is the same as the VPS or PDC time. If a
different 'VPS/PDC time' is indicated, e.g.: '20.15 (VPS/PDC 20.14)',
the VPS/PDC time '20.14' must be entered exactly to the minute
during programming.
2 Use A or B to select the TV station, and D or C to select the
show to record.
If you want to programme a time that is different from the VPS or PDC
time, you must switch off VPS or PDC.
You can page trough channels using CHANNEL q ,
CHANNEL r and page trough days using N , O .
- Only one TV program of a TV channel can be controlled using
'VPS/PDC' at a time. If you want to record two or more TV
programmes on a TV channel using 'VPS/PDC', you will need to
programme these as two separate recordings.
a I do not see all available TV channels
b Please check your correct channel line up in the 'Editor' screen.
Read therefore the section 'The 'Editor' screen in the chapter 'The
GUIDE Plus+® system.
b The GUIDE Plus+® 'Grid' screen contains only those TV channels
that were detected by the GUIDE Plus+® system using a 'channel
identification'. TV channels that do not have this 'channel
identification' are not available in the GUIDE Plus+® system.
Please use 'Manual TIMER programming' to program TV shows of
such TV channels.
- Since the DVD recorder requires a certain lead time (for getting the
disc up to speed and positioning the laser) before recording can start, it
is possible that the recorder will miss the first few seconds of a TV
show recorded with VPS/PDC.
In this case, disable VPS/PDC and enter a start time one minute
earlier.
3 Confirm using the red function button of the remote control
('Record' on the screen).
The TV -show is programmed for recording.
Read the information on the screen.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming a recording (TIMER)
a 'Warning, this programme number has not been
allocated, please go to Editor to set it.' appears on the
screen
b The programme number of the TV channel is not available in the
GUIDE Plus+® system or allocation is wrong.
To change or check the channel data, proceed as follows:
- Press A .
Programming recordings with the
ShowView® System
Select 'Editor' with C .
Thanks to this programming system, you no longer need to tediously
enter the date, programme number, start and finish times. All the
information needed by the DVD recorder for programming is
contained in the ShowView® programming number. This 9-digit
ShowView® number is found in most TV listings magazine.
- Select the TV channel using B or A .
- Press C to go to the right tile.
In case you can receive the selected channel only via an external
receiver, press the red button to select the corresponding source.
- Press the green button.
1 Switch on the TV set. If required, select the programme number
- Enter the programme number of the TV channel using the number
buttons.
If the source you have selected is an external receiver, enter the
programme number that you would also enter at the external receiver
for this TV channel.
for the DVD recorder.
2 Press TIMER s on the remote control.
The 'Schedule' screen will appear
3 Press the red function button ('ShowView').
ShowView Manual
Home
4 Repeat steps 2 to 3 to program all your recordings.
Please enter the ShowView programming number
and press OK to confirm.
= = = = = = = = =
5 End with the GUIDE/TV button.
Grid
No programmes
Search
Schedule Info
To find out how you can check which shows you have
programmed, read the section on 'How to change or delete a
programmed recording (TIMER)'.
Once
0
If one or more recordings have been programmed 'TIMER' will light up
on the display.
4 Enter the entire ShowView number. This number is up to 9 digits
long and can be found next to the start time of the TV programme
in your TV listings magazine.
e.g.: 5-312-4 or 5,312 4
Enter 53124 for the ShowView-number.
Use therefore the number buttons 0..9 on the remote control.
If you make a mistake you can press D or the green action button
to go back a position.
5 Confirm with OK .
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming a recording (TIMER)
a 'Please enter programme number' appears on the
screen
b This message appears when the TV channel has not been assigned in
the GUIDE Plus+® system yet.
Programming recordings without the
ShowView® System
To change channel data, proceed as follows:
- Press A .
Preparation:
•) The TV set is switched on, and, if necessary, the programme number for the
DVD recorder has been selected.
- Select 'Editor' with C .
- Select the TV channel using B or A .
•) the DVD recorder is switched on.
- Press C to go to the right tile.
In case you can receive the selected channel only via an external
receiver, press the red button to select the corresponding source.
1 Press TIMER s on the remote control.
P The 'Schedule' screen appears
- Press the green button.
a I will see some informations about the GUIDE Plus+®
System
b The GUIDE Plus+® System was not installed yet. Read therefore in
the chapter 'The GUIDE Plus+® System' the section 'Set up the
GUIDE Plus+® System'.
- Enter the programme number of the TV channel using the number
buttons.
If the source you have selected is an external receiver, enter the
programme number that you would also enter at the external receiver
for this TV channel.
- Confirm with OK .
a The following message appears on the screen: 'ShowView
number wrong'
b The entered ShowView number is incorrect. Repeat the entry or end
with TIMER s .
b Check time/date (see chapter 'Installing your DVD recorder', section
'Setting the time & date').
ShowView Manual
Home
Schedule displays programmes for Record. Press
Bto use. Press the Red button for ShowView
recording. Press the Green button for Manual
recording. Press Dfor Search. Press Cfor Info.
Grid
Search
Schedule Info
No programmes
ShowView Manual
Home
Please enter the ShowView programming number
and press OK to confirm.
1 2 3 4 5 = = = =
Grid
/Record
21-Oct 20:00 21:30 BBC1
Search
Schedule Info
Freq. Timing
Once
0
2 Press the green button.
P The current date will be displayed.
3 Enter the date using the number buttons 0..9
4 Confirm with OK .
6 The decoded data appears after confirmation.
How can I correct wrong entries?
You can use the colour buttons to make the following settings.
First, the right tile must be highlighted ( C button). Check the
functions (descriptions) in the corresponding colour field before
pressing a button.
If you have already confirmed the entry with OK , you can select one
of the following functions:
Repeat entry: Green colour button
Cancel: Red colour button
Activate 'VPS/PDC'
Keep pressing the yellow action button until 'VPS/PDC' appears instead
of the time.
5 Enter the start time for the show using the number buttons 0..9 .
Confirm with OK .
Setting up repeat recordings
6 Enter the finish time for the TV show using the number buttons
You can choose from the following settings with the green action button:
0..9 Confirm with OK .
'Frequency': 'Once': single recordings
'M-F': Repeated daily recordings (Monday to Friday).
'Mon': Repeated weekly recordings (every week on the
same day e.g. Monday).
7 Check the data you entered.
O If necessary, go back a position to change entered data using
the green function button.
7 If all information is correct, press the OK button. The data is
stored.
8 To end, press TIMER s .
If one or more recordings have been programmed 'TIMER' will light up
on the display.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming a recording (TIMER)
8 Enter the programme number of the TV channel using the number
How to change or delete a
buttons 0..9
programmed recording (TIMER)
Frequency VPS/PDC Home
,
Preparation:
•) The TV set is switched on, and, if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
Grid
/Record
21-Oct 20:00 21:30 BBC1
Search
Schedule Info
Freq. Timing
Once +0
1 Press TIMER s on the remote control while the DVD recorder
is switched on.
P The 'Schedule' screen will appear.
Frequency VPS/PDC Home
, Single recording
Selecting a TV channel from the listing
You can only use this function if data from the GUIDE Plus+® system is
already available.
Grid
Search
Schedule Info
- Press the yellow function button. You will see an overview of all
channels
/Record
21-Oct 20:00 21:30 BBC1
Freq. Timing
Once +0
21-Oct Matrix
Once
0
- Select the TV channel you want to program using D , C , B , A .
You can browse back or forth using CHANNEL q ,
CHANNEL r .
- Confirm with OK .
Programme numbers of the scart sockets 'EXT1' and 'EXT2'
You can also program recordings from external sources.
2 Use B or A to select the programmed recording you want to
change or delete.
- Select the corresponding input socket using B or A . 'EXT1'
( EXT1 TO TV-I/O ), 'EXT2' ( EXT2 AUX-I/O ).
Depending on the programming method (using GUIDE Plus+®
system, with/without ShowView® system), it is not possible to
carry out certain changes using the function buttons. Therefore,
always check the function of the corresponding button (description
in the colour field) before pressing the button.
- Confirm with OK .
Changes using the colour buttons
You can use the colour function buttons to make the following settings.
Make sure that the right tile is selected.
Delete programmed recording
'Frequency': Green function button
'Once': single recordings
Press the red action button in the left tile.
Changing the TV channel
'M-F': Repeated daily recordings (Monday to Friday).
'Mon': Repeated weekly recordings (every week on the
same day, e.g. Monday).
You can make this change only for recordings that were not set using
the 'Grid' screen.
In the case of recordings using the 'Grid' screen, centre tile is not
available.
- Select the centre tile with C .
Activate VPS/PDC ('Timing'): Yellow function button
Using this button, you can activate
(appears) or deactivate ('VPS/PDC'
disappears) 'VPS/PDC' in tile
- Press the yellow function button.
'Timing'
- Select the TV channel you want using B , A , D , C . Sender.
- Confirm with OK .
9 To find out how you can go back and change the data, read the
section on 'How to change or delete a programmed recording
(TIMER)'
Activate VPS/PDC
Keep pressing the yellow function button in the right tile until
'VPS/PDC' appears in the 'Timing' line instead of the time.
If you programm a recording using the GUIDE Plus+® System, the
VPS/PDC time will be taken automatically. VPS/PDC can be switched
on or off without readjusting the start time.
If any of the TIMER blocks are in use, 'TIMER' will light up on the
recorder display.
Setting up repeat recordings
You can choose from the following settings in the right tile using the
green function button:
'Frequency'':Once': Once recordings
'M-F': Repeated daily recordings (Monday to Friday).
'Mon': Repeated weekly recordings (every week on the
same day, e.g. Monday).
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming a recording (TIMER)
3 To end, press TIMER s .
A message appears few minutes before the recording is about to
start if the DVD-recorder is tuned to a different TV channel as
programmed. If you confirm this message the TV channel will be
changed and the recording started.
Cancel a programmed recording in
progress
A programmed recording will run as long as the end of the TV show is
reached (end time of the schedule or end time out of the GUIDE
Plus+® System)
If you switch off the DVD-Recorder with STANDBY m the
DVD-Recorder will be switched off after the recording is completed.
If you want to cancel the programmed recording proceed as follows:
1 Press the red function button
2 Select 'Yes' using D and confirm with OK .
O The programmed recording can also be canceled as described
in the previous section 'How to chnage or delete a
programmed recording (Timer)'.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback from the HDD
The position where playback was interrupted will be automatically
stored. By pressing PLAY G , playback resumes at this position.
General
Each recording stored on the HDD is displayed in the media browser
with a corresponding index picture.
Additional playback features
1 Press BROWSER HDD on the remote control or HDD on the
DVD recorder.
P The Media Browser appears.
Search by time
During playback of a title from the HDD or recordings in the time shift
buffer, you can search for positions by directly entering the time:
1 Press SYSTEM MENU during playback of a title.
P The system menu appears.
2 Press C in line 'Toolbar' to select 'Options'.
3 Press B to select 'Time search' and confirm with C .
a It is not possible to select 'Time search'.
2 Select the title you want using B , A on the remote control or
b A title of the time shift buffer is played back that has no end yet (no
programme change, or TV show is not over yet).
DOWN , UP on the device.
You can switch a page forward or back using CHANNEL q ,
CHANNEL r .
P The time of the current playback position is displayed.
3 You can choose one of the following options to start playback:
4 Use the number buttons 0..9 of the remote control to enter the
time where you want playback to start.
O
OK
Playback always starts at the beginning of the selected title.
5 Confirm with OK .
P Playback starts at the desired position.
O
PLAY G
Playback will start at the position where it was interrupted in
the selected title( STOP h ). This also works if other titles or
DVDs have been played in the meantime.
Repeat
4 You can use the following buttons during playback:
You can choose the entire title for repeated playback.
1 Press BROWSER HDD and choose the desired title with B ,
A .
2 Press OK to start playback.
3 Press the green function button.
P A symbol appears on the screen to display the repeated
playback.
O
O
N , O
O To switch of repeat play press the green button again.
Briefly press: If chapter markers are available, start of
current chapter, previous chapter (press twice), next chapter
Hold down: during pause: Slow motion
during playback: Qquick motion.
The symbol disappears.
JUMP FWD , JUMP BACK
Jump back or forward by a fixed time period.
Read section 'Set up/Jump forward, Jump back' in
chapter 'User preferences for the HDD' on how to set up this
time period.
O
O
INFO
Display/Hide navigation bar with additional information.
PAUSE 9
Still picture. Go forwards or backwards one frame at a time
using C , D .
5 Press STOP h to end playback.
P You will return to the media browser.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback from the HDD
Zoom feature
The Zoom feature allows you to enlarge the video image and pan
through the enlarged image during play back from the HDD or from
the time shift buffer.
The media browser
1 During playback, press PAUSE 9 at the position where you
want to enlarge the picture.
P You will see a still picture.
2 Press SYSTEM MENU .
P The 'System Menu' appears.
Each recording stored on the HDD is displayed in the media browser
with an index picture. A actual recording of a TV show in the time shift
buffer is also displayed here.
Please observe that title/chapter editing is only possible to a certain
degree with such recordings.
3 Press C in line 'Toolbar' to select 'Options'.
4 Press B to select 'Zoom' and confirm with C .
P On the screen arrows appears to indicate the directions. If
neccessary switch on the info bar with INFO .
Title editing includes:
- change
- delete
- archive
5 Select with D , C , A , B the area you want to enlarge.
- lock (child lock)
- protect (against automatic deletion)
O zoom in
blue function button
Titles in the Time shift Buffer marked for storage on the HDD, can
only be locked or deleted.
O zoom out
yellow function button
O You can also pan in the enlarged picture using B , A , D ,
C .
Symbols in the 'Media Browser'
6 End with the red function button.
If you call up the Media Browser with the BROWSER HDD button,
following symbols can appear in the infobar at the top of the screen:
P Play back starts automatically
'P' This title was marked in the Time Shift Buffer for the storage on
the HDD. This title can only be deleted or locked (child lock)
'E' This title has been played once (has been 'watched'). If there is no
storage capacity free on the HDD such 'watched' titles will be
deleted automatically. You can change these setting in the title edit
menu ( EDIT button, blue button, EDIT button )
Titles that were not played back, will have no symbol.
'F' The title is protected against editing and deleting. If the title is not
protected, no symbol will be shown.
'i' Child lock is activated. The index picture is switched off. Playback
starts only if the right PIN code was entered. By default '0000' is
defined as the PIN code. In the section 'Changing the PIN code' in
chapter 'Access control (Child Lock)' you will find how you can
change this code.
'Q' The marked titles will be stored (archived) on a DVD+RW/+R.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback from the HDD
Change order for the media browser
Change title settings
Your may choose only titles that meet certain criteria for the overview.
This order will remain until you exit the media browser.
Use this function to change the title settings.
1 Press BROWSER HDD on the remote control.
1 Press BROWSER HDD on the remote control.
P The Media Browser appears.
P The Media Browser appears.
2 Select the title you want to change with B , A .
2 Press D .
3 Choose one of the following functions with the colour buttons of
P The 'Order Menu' appears.
your remote control:
O Delete title:
3 Select one of the following options using B or A and confirm
red function button
with OK .
The tiltle (recordings) will be erased from the HDD.
O 'Alphabetical':
Alphabetic order
O Archive title:
green function button
O 'Recording Date':
The title will be transferred to DVD+RW/+R. If it is not
possible to record on a DVD+RW/+R, an error message
appears (disc not inserted,...).
If you want to archive several titles, mark the desired titles
with SELECT . You can unmark the title using the same
button.
Sorting according to the date of the recording
O 'Delete Order':
Sorting according to the order of the automatic deletion. If
there is too less space for new recordings on the HDD , this
order shows which recordings will be automatically deleted
first.
O Lock title (child lock):
yellow function button
O 'Protected':
Playback starts only if the right PIN code was entered. By
default '0000' is defined as the PIN code. In the section
'Changing the PIN code' in chapter 'Access control (Child
Lock)' you will find how you can change this code.
Order according to the recordings protected against deletion.
O 'Last Played':
Sorting according to the titles last viewed.
O Protect title against editing, automatic deletion:
blue function button
Depending on the selected order, it may not be possible to select some
titles.
An error message will appear if you try to edit this title.
Automatically deletion will take place, if your HDD will run full
with recordings. Stored recordings will be deleted in a certain
order. See details in the section 'Symbols in the media
browser'
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback from the HDD
'Video edit'
Edit title
Here you can insert/clear chapter markers, hide chapters, merge
chapters, or divide the title.
Use this function to adapt the title (recording) to your personal
preferences.
1 Press BROWSER HDD on the remote control.
P The Media Browser appears.
2 Select the title whose settings you want to change with B , A .
Press EDIT .
3 Select one of the displayed functions with B , A and confirm
with C to proceed with the changes.
1 Press BROWSER HDD on the remote control.
Depending on the selected function, you can choose different
functions using the colour buttons on the remote control. The
function of the button may vary. Therefore, read the function in
the help line before pressing the button.
P The Media Browser appears.
2 Select the title whose settings you want to change with B , A .
Press EDIT .
O 'Title name'
Change the name of the title.
3 Select 'Video edit' and confirm with C .
P Playback starts automatically.
O 'Clear chapters'
All chapter markers within the selected title will be deleted.
4 Search the position where you want to make changes with D ,
O 'Video edit'
C , N , O .
Please read in the next chapter which modifications were
possible.
To enlarge the actual position of the timebar in several steps you
can use A . You can switch back using B .
5 Press PAUSE 9 :
O You can insert or remove chapter markers to find a scene
easily with the OK button.
6 Choose one of the following functions with the colour buttons of
your remote control:
O 'DIVIDE'(red function button):
You can divide a title in as many parts as you like.
O 'MERGE'(green function button):
You can merge the current chapter with the previous chapter.
(The previous chapter marker will be deleted). Please observe
that you cannot use this function with titles.
O 'KEYFRAME'(yellow function button):
To select an index picture that designates this title in the
media browser.
You can select this function only during still (button
PAUSE 9 ).
O 'HIDE'(blue function button):
You can hide or unhide certain chapters during playback (e.g.
unwanted scenes).
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback from the HDD
Editing recorded titles (name)
Divide title
From the GUIDE Plus+® data the title (name) of a TV show will be
taken automatically (e.g. 'ROCKY'). Otherwise, only the programme
number (programme name) and the time will be stored as the name of
the recording. The name of the recording can only be changed after the
recording has finished.
You can divide a title in several parts (titles) as large as you like. Each of
these parts (titles) is designated by a separate index picture.
You can also use this function to separate and delete an undesired end
of the recording (commercial).
Warning! You cannot undo this division!
1 If necessary, press STOP h to stop playback.
1 Press BROWSER HDD on the remote control.
P The Media Browser appears.
2 Press BROWSER HDD on the remote control.
P The Media Browser appears.
2 Select the title you want to divide using A or B
3 Use A or B to select the title whose title you want to edit.
3 Press EDIT on the remote control.
P The title edit menu appears on the screen.
4 Press EDIT .
P The title edit menu appears on the screen.
4 Select the line 'Video edit' and confirm with C .
P Play back starts automatically
5 Select the line 'Title name' and confirm using C .
P The field for editing the title appears.
5 Search the position you want to divide the title using N , O .
Press PAUSE 9 on the remote control.
6 Use C or D to select the position where the letter/number/icon
P You will see a still picture.
is to be changed or re-entered.
To find the right position you can step a frame forward or
7 Change the icon using A or B .
backward using the D , C button.
O You can switch between upper and lowercase using
SELECT .
6 Press the red function button
P A message appears on the screen saying that the title is being
O You can clear all characters using the red function button
divided.
('CLEAR').
P The divided title will appear in the media browser with a new
index picture. The last position in the name will increase by
one.
O You can stop editing without storing the change by pressing
the green function button('CANCEL').
Enter characters using 0..9
Keep pressing the number button until the desired character or number
is displayed. You can select language-dependent special characters at
the corresponding letter using N or O e.g.: ä, press 2 for a and
keep pressing O until ä appears.
This completes the division of the title.
For special characters, press 1 several times.
The position for the following character is selected automatically.
Press 1 to insert an empty space.
Press the red function button to delete.
8 Repeat 6 and 7 until you have made the changes you want.
9 Save the new name with OK .
0 To end, press EDIT .
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback from the HDD
Delete titles/recordings from the HDD
Insert/remove chapter markers
You can remove titles/recordings from the HDD to use the capacity
from the HDD for new recordings.
To find you special scenes in one title faster, you can insert chapter
markers. These markers can also be deleted.
1 Press BROWSER HDD on the remote control.
1 Press BROWSER HDD on the remote control.
P The Media Browser appears.
P The 'Media Browser' appears on the screen.
2 Select the title/recording you want to delete using A or B
2 Select the title you want to modify using B , A .
3 Press the red function button ('DELETE')
3 Press EDIT on the remote control
P A note appears if you really want to delete this title.
P The title editing menu appears on the screen.
O If you want to remove all automatically created chapter
markers confirm select the line 'Clear chapters' and confirm
with C .
If the red function button has no function ('DELETE' appears
grey) check if the title is protected. You will see this on the
symbol 'F' on the screen.
Unprotect the title using the blue function button.
4 Select the line 'Video edit' and confirm with C .
4 Select 'Yes' using D and confirm with OK .
P Play back starts automatically.
P The title is being deleted from the HDD.
O If the message window was closed, confirm the line with
O Insert chapter markers
C again.
- Search the position where you want to insert a marker with
D , C , N , O .
- Press PAUSE 9 .
- Press OK . The marker will be inserted.
O Remove chapter marker
- Press PAUSE 9 .
- Search the chapter marker you want to remove with N ,
O
- Press OK . The marker will be deleted.
5 End with EDIT .
P You will go back to the Media Browser.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback from the HDD
9 Set the end marker with the blue function button.
P The 'hidden' area is greyed out.
Hide chapters (sections)
P The description of the blue function key changes to 'HIDE' .
By default, all chapters are visible. You can hide or unhide certain
chapters during playback (e.g. unwanted scenes).
End with EDIT .
P Additionally to the original title the edited title appears in the
'Media Browser'.
In the editing mode, you will recognise a hidden chapter by a grey
background and the description of the blue function button:
You can delete the edited title without deleting the original
one.
O 'HIDE':
If the original title is being deleted, the edited tiltle
will be alsodeleted.
Chapter is visible and can be hidden with the blue button.
O 'SHOW':
Chapter is hidden and can be made visible with the blue
button.
During playback, the 'hidden' scene is skipped. If you want to archive
the title you can decide to archive the original title or the edited one.
O Archiving of the 'edited' title
The 'hidden' szenes were not copied on the DVD+RW/+R.
To hide a certain scene, proceed as follows:
O Archiving of the 'original' title
1 Press BROWSER HDD on the remote control.
The 'hidden' szenes were copied as 'hidden' on the
DVD+RW/+R. How you can make them visible again you can
read in the chapter ' Managing the disc content'.
P The 'Media Browser' appears on the screen.
2 Select the title you want to edit using B , A .
3 Press EDIT on the remote control.
P The title edit menu appears on the screen.
4 Select 'Video edit' with B and confirm with C .
P Play back starts automatically
5 Search the beginning of the scene (section) you want to hide using
O , N , D , C . Press PAUSE 9 .
6 Set the start marker with the blue function button.
P The description of the function key changes from 'HIDE' to
'STOP HIDE'.
7 Search for the end of the scene (section).
O Use O , N , D , C to search for the end of the scene.
P The area is being marked.
To enlarge the actual position of the timebar in several steps you
can use A . You can switch back using B .
To find the right position you can step a frame forward or
backward using the D , C button.
To select the end of the title use O
8 Press PAUSE 9 at the corresponding position.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on a DVD+RW/+R
If this button is not visible on the screen, check if this title is
available in the 'Time shift Buffer'. If necessary switch of the set
using STANDBY m or use the 'Flush Buffer' function (button
SYSTEM MENU , menu 'Set up')
Archiving (storing) titles on a
DVD+RW/+R
P A message indicating the process appears both on the screen
You can choose the title of the HDD that you want to transfer on a
DVD+RW/+R. The copying process is done at a higher speed than the
recording. Therefore, you can transfer an 8-hour recording in 'M8'
recording mode on a DVD+RW/+R in just 30 minutes. This time
depends on the recording mode used.
and in the display.
P During and after the archiving process, you see the TV show
of the currently selected TV channel. The buttons D , C ,
JUMP BACK , JUMP FWD , PLAY G , PAUSE 9 are
without function during archiving. Timer recordings will take
place.
Please observe the following information:
You cannot change the recording quality. You can only use the
same recording quality that was used for recording on the HDD.
•
•
Interrupt the process
Press the yellow function button. If necessary call up the informatoon on
the screen using the INFO button.
New recordings will always be added at the end of existing ones.
Ensure that the 'Empty title' after the last recording is large
enough.
Finalising a DVD+R
The index picture from the title will be copied from the HDD and
stored on the disc.
•
•
•
If recordings were stored (archived) on a DVD+R you have to finalise it
to make play back in a DVD-Player possible.
- Press DISC MENU and then STOP h to mark the first title.
Should you reach the maximum number of chapters per disc (255),
the recordings will be transferred without chapter markers.
- Press A to go to the 'disc info screen'
- Press C and select then the line 'Finalise disc' using B .
- Confirn with OK .
The following information will also be stored on the disc in the
process:
Chapter, recording mode, programme name (if available) title of
the recording (name), date and time of the recording, index
picture.
Protect disc against accidental
recordings
If you archive the edited title, the 'hidden' chapters will be skipped
and will no longer be available on the DVD+RW/+R.
•
To prevent an accidental erasing of important recordings, you can
protect the entire disc. It is only possible to protect the entire disc.
Protecting specific recordings on a disc is not possible.
1 Change the titles in the media browser to meet your preferences.
(divide titles, change title name, hide chapter, ...)
What happens with DVD+R discs?
As long as these discs are not finalised, you can protect them against
accidental recording.
2 Insert a DVD+RW/+R on which you want to store the selected
titles.
Please ensure that:
1 Insert the disc to be protected.
•) the DVD+RW was not protected against accidental recordings.
For more information, read the next section 'Preventing accidental
erasing of discs'.
•) there is enough space for all selected titles at the end of the
DVD+RW/+R.
2 Press STOP h on the remote control while the index screen is
displayed.
P The first title is highlighted.
3 Press BROWSER HDD .
3 Press A .
P The media browser appears with an overview of all recordings
on the HDD.
P This takes you to the disc info screen.
4 Press C .
4 Select the title you want to copy on the DVD+RW/+R using B ,
Select 'Protection'.
Confirm with C .
A .
O If you want to archive several titles at a time, mark the desired
5 Select 'Protected' using B and confirm with OK .
titles with SELECT .
6 Press D and then DISC MENU to terminate.
What is the order of archiving?
P The entire disc is now protected.
The titles will be transferred to the DVD+RW/+R in the same order as
they where selected using the SELECT button.
If you attempt to record on a protected disc, 'DISC LOCK' will
appear on the display and 'Disc locked' on the screen.
If you decide later to record on this disc again, repeat the above steps
but select 'Unprotected' at step 5 .
5 Start the archiving process by pressing the green function button.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback from a disc
O To continue playback, from the disc press DISC MENU .
General notes on playback
With this DVD recorder you can play back the following systems:
•) DVD Video
•) (Super)Video CD Disc
•) DVD+RW Disc
•) DVD+R Disc
•) DVD-RW (video mode, finalised)
Inserting a disc
1 Press the OPEN/CLOSE J button on the front.
•) DVD-R
•) CD-R
•) CD-RW
OPENING
P01
•) Audio CD
•) MP3-CD
You can operate the video recorder using the remote control or the
buttons on the front of the DVD recorder.
P The disc tray will open. While the disc tray is opening, the
display shows 'OPENING' and then 'TRAY OPEN' when the tray
is fully open.
a The display will read 'PIN'
b The child lock has been activated for the inserted disc. Read the sections
on 'Child lock' and 'Releasing a disc' in the chapter on 'Access control
(child lock).
2 Carefully place the disc in the tray with the label facing up and
press PLAY G or OPEN/CLOSE J .
P 'CLOSING' and then 'READING' will appear in the display. The
information on the disc will be read.
a The menu on the screen is showing an 'X'
b Some DVD discs can be manufactured so that certain steps are required
before the disc can be played, or so that only limited operation is possible
during playback. When an 'X' appears on the screen the selected feature
is not possible.
How do I insert a double-sided DVD?
Double-sided discs do not have labelling over the whole surface. The
labelling for each side is in the centre of the disc. To play a side its label
must be facing up.
a The screen is showing regional code information
b Since DVD films are not normally released in all parts of the world at the
same time, all DVD players have a specific regional code. Discs can be
given a regional code. If the regional codes differ between the player and
the disc, playback is not possible.
Opening/closing the tray using the remote control
You can open and close the disc tray using the remote control.
Press and hold the STOP h button on the remote control until the
dialog box shows 'OPENING' or 'CLOSING'.
b The regional code is shown on the label on the back of the machine.
b The regional code does not apply to recordable DVDs.
a I can see the message 'EMPTYDISC'
b The disc does not contain any recordings.
a 'DISC ERR' will appear on the display
b Recording could not be completed correctly because of a disc error. Check
the disc and clean it if necessary.
Playing a DVD videodisc
a A dialog box appears asking you whether you want to delete
the contents or eject the disc
b The disc inserted is a DVD+RW but its contents are not DVD
video-compatible (e.g. a data disc). Recordings on this disc can only be
made if the entire disc is first deleted with the REC/OTR n button.
A menu may appear when a DVD is played back. If the titles and
chapters are numbered, press a number button on the remote control.
O You can also use the D , C , A , B buttons or number
buttons 0..9 to select a menu item and confirm with OK .
O You can also access the menu using DISC MENU on the
Switch over to the actual TV channel during
playback
As soon as you turn on the DVD recorder, the currently selected TV
channel on the DVD-Recorder is recorded in a temporary storage
(Time shift Buffer).
remote control.
1 If playback does not start automatically, press PLAY G .
P title/chapter number, elapsed time will appear on the display.
Recordings in the time shift buffer will be automatically deleted e.g.
after 3 hours if the period of the time shift buffer is set to 3 hours
(factory setting).
C01
2:04
You can play back a disc, while the current TV show is still being
recorded.
2 To stop playback, press STOP h on the remote control or
1 To interrupt playback from a disc, press TUNER
P You will see the TV-show from the selected TV channel on
the DVD-recorder
h on the DVD recorder.
3 To remove the disc, press OPEN/CLOSE J on the front of the
DVD recorder.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback from a disc
Playing a DVD+RW/ +R disc
Playing an MP3 CD
MP3 (MPEG1 Audio Layer-3) files are highly compressed music files.
Using this technology the data volume can be compressed by a factor
of 10. This means it is possible to record 10 hours of music in CD
quality on a single CD-ROM.
1 If the disc is write-protected or a finalised DVD+R disc, playback
starts automatically.
When creating MP3 CDs please note the following:
File system: ISO9660
Directory structure: maximum of 8 levels
Formats: *.mp3
C01 ANNA
P01
Filenames: maximum of 12 characters (8+3)
Maximum of 32 albums, 999 titles
Supported sampling frequencies: 32, 44.1, 48 (kHz). Music with
sampling frequencies other than these will be skipped.
Supported bit rates: 32, 64, 96, 128, 192, 256 (kbit/s)
ID3 Tag: Version 1, 1.1. In later versions the directory name is
displayed as the album and the filename as the title.
2 If playback does not start automatically, use the B or A button
to select the title you want to play on the index screen.
You can also use the DOWN or UP button on the front.
With N , O you can jump to the begin or the end of the
index screen.
Important notes for playback:
Only the first session of a multi-session CD will play back.
3 Press the PLAY G button.
P title/chapter number, elapsed time will appear on the display.
1 Insert an MP3 CD.
a I can see the message 'EMPTYDISC'
b The disc does not contain any recordings.
P Playback starts automatically.
MP3 CD display
4 To stop playback, press STOP h on the remote control or
If the TV is on, the MP3 CD screen appears automatically.
h on the DVD recorder.
During playback, the current track number and its elapsed playing time
will be shown on the TV screen and on the recorder display.
During stopped playback ( STOP h button) the numbers of the
albums will be shown on the TV screen and on the display.
5 To remove the disc, press OPEN/CLOSE J on the front of the
DVD recorder.
Further information on the album, track and artist will also be displayed
if included in the ID tag.
Playing an audioCD
2 Stop playback using STOP h .
P The number of albums is displayed in the display.
O Using N or O select the next or previous title.
You can also use the DVD recorder to play audio CDs
O You can also use the T/C button to select titles and albums.
- Press the T/C button and use the C or D button to select
the 'T' symbol for title or 'C' for chapter. Use the B or
A buttons or the number buttons 0..9 on the remote
control to select the number of the title/chapter.
If the TV is on, the audio CD screen appears automatically.
During playback, the current track number and its elapsed playing time
will show on the TV screen and on the recorder display.
1 Insert an audio CD.
O You can also use the repeat functions ( SELECT button).
P Playback starts automatically.
2 Stop playback using STOP h .
P The number of tracks and the total time are displayed.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback from a disc
Playing a (Super) VideoCD
(Super) Video CDs may be equipped with PBC (Play Back Control).
This means that special playback functions (menus) can be directly
selected. The video CD must be PBC compatible (see CD case).
'PBC' is active in the default settings.
1 Insert a (Super) Video CD.
P If the 'h' symbol appears in the display, start playback by
pressing PLAY G .
O If a menu appears on the screen, use the remote control
buttons indicated on the screen to select the menu option you
want (PREV= N , NEXT= O ) or with the number
buttons 0..9 .
O If a PBC menu consists of a list of titles, you can select a title
directly.
O Use RETURN to go back to the previous menu
2 Stop playback using STOP h .
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Additonal playback features
General
Still picture
1 During playback, press PAUSE 9 to stop playback and display a
DVD's are divided in titles and chapters.
still picture.
O During playback, press O to go to the next title. If there
are several chapters within a title, the next chapter.
C01
2:04
O Press N to return to the start of the current title/chapter.
O Press N twice to return to the start of the previous
title/chapter.
Frame advance via menu bar
- During a still picture press SYSTEM MENU on the remote control.
The menu bar will appear at the top of the screen.
Use the T/C (title/chapter) button
- Press T/C (title/chapter) and then use A or B to select the
appropriate title.
Make sure the symbol 'T' (title) is selected in the menu bar.
- Use T/C to select chapters within a title. Press T/C and use C to
select the 'C' symbol (chapter).
- Select the '
' symbol using C or D and confirm with B .
I
- You can now use the D or C button to go forwards or backwards
one frame at a time.
- If necessary, switch the menu bar off with the SYSTEM
MENU button.
Now select the appropriate chapter with A or B .
2 To continue playback, press PLAY G .
Searching a disc
Slow motion
You can search the disc for a recording at 4x, 8x or 32x playback
1 During playback press PAUSE 9 on the remote control. Now
speed. Other speeds can only be selected via the menu bar ('
').
K
hold down N or O to switch to slow motion.
1 During playback, press and hold N (reverse) or O (forwards)
to switch to the search feature.
O You can switch between different speeds using N or O .
O You can switch between the playback speeds using
N / O .
Slow motion via menu bar
- During playback press PAUSE 9 and then SYSTEM MENU on
the remote control. The menu bar will appear at the top of the screen.
2 To continue playback, press PLAY G at your chosen location.
a No sound
- Select the ' ' symbol using C or D and confirm with B .
J
b The sound is switched off in search mode. This is not a fault in your
machine.
- You can now use the D or C button to select different forward and
backward slow motion speeds.
- If necessary, switch the menu bar off with the SYSTEM
MENU button.
Search feature via menu bar
- During playback press SYSTEM MENU on the remote control.
The menu bar will appear at the top of the screen.
2 To continue playback, press PLAY G twice.
- Select the '
' symbol using C or D and confirm with B .
K
- You can now use the D or C button to select different forward and
backward search speeds.
- If necessary, switch the menu bar off with the SYSTEM
MENU button.
- To continue playback, press PLAY G .
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Additonal playback features
Repeating a passage (A B)
You can repeat a particular passage within a title/chapter. You need to
indicate the start and end of the passage.
Search by time
Using this feature you can select where playback should start (select
elapsed time).
1 During playback press PAUSE 9 at the start point.
1 During playback press SYSTEM MENU on the remote control.
P You will see a still picture.
P The menu bar will appear at the top of the screen.
2 Keep pressing SELECT until '
' appears on the screen.
0
2 Select the ' ' symbol using C or D and confirm with B .
L
P The start point is now saved.
P Playback is stopped and a box appears on the screen showing
the elapsed time.
3
Press PLAY G to start playback.
3 Enter the start time with the digit keys 0..9 from where playback
should start.
4 When the end point is reached press OK .
P ' ' appears on the TV screen.
1
4 Confirm with OK .
Playback now takes place within these points.
a The time entered will flash on the screen
b The selected title is shorter than the time entered. Enter a new time
or cancel the function by pressing SYSTEM MENU .
5 To end the repeat, press the STOP h button.
O You can also keep pressing the SELECT button until the
displays disappear.
5 Playback starts at the time you entered.
Repeat/Shuffle play
Scan feature
You can mark entire sections or the whole disc for endless playback.
Depending on the type of disc (DVD video, DVD+RW, video CD) you
can select a chapter, title or the entire disc.
This feature plays back the first 10 seconds of each chapter (DVD) or
track (CD).
1 During playback, press SELECT . Select '
' using
6
1 Select the desired chapter, title or the entire disc and start
SELECT .
playback.
P After 10 seconds the DVD recorder switches to the next
chapter/index.
2 During playback, press SELECT . By pressing SELECT again
you can chose from the following options:
O To start playback at the relevant chapter/index press
•) '
•) '
': repeat chapter (DVD only)
': repeat track/title
2
STOP h and then PLAY G .
3
5
/
•) '
•) '
': repeat entire disc (Video CD, Audio CD only)
': Shuffle
•) Display disappears: no repeat
3 To end the repeat, press the STOP h button.
O You can also keep pressing the SELECT button until the
displays disappear.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Additonal playback features
Camera angle
Select the audiolanguage
If a DVD contains scenes that have been shot from different camera
angles you can select these camera angles for playback.
Many pre-recorded DVD discs have more than one audio language.
The language initially selected for playback will be the one you selected
when you first set up the DVD recorder. However you can change the
audio language of the inserted disc at any time.
You can change the audio language either using the menu of the
inserted disc ( DISC MENU button) or the DVD recorder's menu bar
( SYSTEM MENU button). The audio languages for DVD playback in
the two menus may be different. Please note that with some DVDs the
audio language and/or subtitle language can be changed only via the
DVD menu.
1 During playback, press PAUSE 9 .
P You will see a still picture.
2 Press SYSTEM MENU and select the ' ' icon using C .
F
a The ' ' symbol will be hidden
F
b The selected scene has been shot from only one camera angle. This
feature is therefore not available. For more information please read
the cover of your DVD disc.
1 During playback press SYSTEM MENU and select the ' ' icon
D
using C .
3 Select the required camera angle with B or A .
2 Select the required audio language using B or A .
O You can also directly enter the number with the number
O You can also enter the number directly using the number
buttons 0..9 .
buttons 0..9 .
P Play continues in the new audio language.
P After a short time, playback will resume from the new camera
angle.
The ' ' symbol will remain visible until a scene starts for
F
which there is only one camera angle.
Subtitles
Many pre-recorded DVD discs have more than one subtitle language.
The language initially selected for playback will be the one you selected
when you first set up the DVD recorder. However you can change the
subtitle language of the inserted disc at any time.
You can change the subtitle language either using the menu of the
inserted disc ( DISC MENU button) or the menu bar ( SYSTEM
MENU button). The subtitle languages in the menus may differ.
Zoom feature
The Zoom feature allows you to enlarge the video image and pan
through the enlarged image.
1 During playback, press PAUSE 9 .
P The DVD recorder switches to 'PAUSE'. You will see a still
picture.
1 During playback press SYSTEM MENU and select the '
' icon
E
using C .
2 Press SYSTEM MENU and select the ' ' icon using C .
G
2 Select the required subtitle language using B or A .
O You can also enter the number directly using the number
3 Select the required zoom factor using B or A .
P When 'press OK to pan' appears on the screen, the zoom
process is complete.
buttons 0..9 .
O You can switch off subtitles again with 0 or by pressing 'off'.
P Playback continues in the new subtitle language.
4 Press OK . Using A , B , C , D select the part of the image
you wish to view.
5 Confirm with OK .
6 To stop the feature, press PLAY G and then SYSTEM MENU .
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing the disc contents
General
Favorite Scene Selection
In this menu you can adapt a title to suit your particular needs.
You can insert/delete chapter markers, hide chapters, select a new
index, or split up a title.
Charly 1
00:29:59 • M1
Fri15/02/2003
In this menu you can adapt a title on a DVD+RW/+R to suit your
particular needs.
You can insert/delete chapter markers, delete all chapter markers, or
split up the title. Press EDIT on the remote control during recording
to open this menu.
Empty title
01:30:01
Insert chapter markers
When a recording is made to disc, the following additional information
is also stored at the beginning of the recording:
•) Name of the recording
If a name has not been assigned to the TV channel, only the programme
number and time are stored as the name
•) Length of the recording
During recording, you can set or delete chapter markers within a title.
The maximum number of chapters per disc is 255 and 99 per title. If
one of these limits is reached the following message will appear on the
screen: 'Chapter limit'. You need to delete some markers before you
can insert new ones or make recordings.
•) Record type (Quality)
•) Date of the recording
•) Index picture of the recording
1 During playback, press EDIT on the remote control at the
appropriate point.
P The 'Favorite Scene Selection' menu appears on the TV
screen.
A marker will be set every 5-6 minutes if the 'Auto chapters' function
is activated in the 'Recordsettings ' menu. This marker is known as a
'chapter'.
These markers can be changed when the recording has finished.
Favorite Scene Selection
Insert marker
Press OK
visible
Can markers be set on a DVD+R disc?
Current chapter
Delete marker
Delete all markers
New index picture
Divide title
Markers can be set on these discs if they have not been finalised.
It is also possible to add 'chapters' later. This means that scenes you do
not want to see during playback can be hidden or skipped. During
playback you can watch your recording as a continuous sequence
without the hidden chapters.
Press EDIT to exit
2 Confirm 'Insert marker' by pressing OK .
P 'Inserting marker' appears on the TV screen.
'X' will appear on the screen:
This DVD is write-protected or the disc is a finalised DVD-R. Subsequent
changes cannot be made.
3 To stop this function, press EDIT .
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing the disc contents
a The number of chapters ('C') has increased by two or more
numbers
Hiding chapters
b This is the case when you want to hide a chapter that, due to
automatic chapter numbering (if switched on), stretches over two or
more chapters. In this case, you must delete the start of the
automatically generated chapter:
- Press T/C twice while the editing menu is displayed to change the
chapter number.
Initially, all the chapters are visible. You can hide chapters for playback
(e.g. unwanted scenes) or make them visible again. In editing mode,
hidden chapters are shown darker.
A chapter always consists of a start marker and an end marker.
To hide a certain scene, proceed as follows:
- Select the chapter between the new markers using B or A . Press
PAUSE 9 .
1 Search the beginning of the scene you want to hide. Press
PAUSE 9 .
- Select 'Delete marker' with B to delete the current chapter
marker. Confirm with OK . The current chapter number decreases by
one.
Favorite Scene Selection
7 Press T/C twice to change the chapter number 'C'.
Insert marker
Press OK
visible
Current chapter
Delete marker
Delete all markers
New index picture
Divide title
8 Select the previous chapter with B , since you are already in the
next chapter (end of the chapter is also the beginning of the next
chapter).
9 Wait until the chapter has been played and press PAUSE 9 to
Press EDIT to exit
stop playback.
0 Select 'Current chapter' using B or A .
2 Press EDIT on the remote control to call the 'Favorite Scene
A Using C select 'hidden'.
Selection' editing menu.
P The picture is shown darker.
3 Set the start marker using OK .
Switching quickly
P The number of chapters ('C') in the menu line will increase by
one.
You can switch between show chapters ('visible') and hide chapters
('hidden') quickly and easily using SELECT .
This function is independent from the selected line.
4 Search for the end of the scene.
O You can also use O or N to search faster for the end of
the scene.
B To end, press EDIT .
Make sure that you do not jump into the next title (title
number 'T' must not change).
During playback this chapter will be skipped.
If the chapter is not visible, select 'visible' in step A with C .
O Only chapters within a title can be hidden.
5 Press PAUSE 9 at the corresponding position.
Deleting chapter markers
6 Set the end marker with OK . This will also be the start marker of
Within a title you can delete either all markers or individual markers.
the next chapter.
P The number of chapters ('C') in the menu line increases by
one.
Favorite Scene Selection
Insert marker
Press OK
visible
Current chapter
Delete marker
Delete all markers
New index picture
Divide title
Press EDIT to exit
1 While the relevant chapter is playing, press EDIT on the remote
control.
P The 'Favorite Scene Selection' menu appears on the TV
screen.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing the disc contents
How can I select different chapters?
Dividing titles
- Press the T/C button on the remote control. Titles and chapters are
You can divide a title into several sections (titles) of any size. Each of
these sections (titles) is identified by its own index.
Note: This division cannot be undone.
displayed at the top of the screen.
- Select title (T) or chapter (C) with C or D .
- Use A or B to select the title/chapter channel you want to edit.
Can I divide titles on DVD+R discs?
2 Use B to select:
As recordings on DVD+R discs cannot be overwritten, it is not possible
to divide titles on DVD+R discs.
O line Delete marker' for this chapter
O line 'Delete all markers' for all chapters within the selected
1 While the relevant title is playing, press EDIT on the remote
title.
control.
P The 'Favorite Scene Selection' menu appears on the TV
3 Confirm with OK .
screen.
O You will be prompted to press OK again to make sure you
really want to delete all markers.
O If you do not want to, press the D button.
Favorite Scene Selection
4 To end the menu , press EDIT .
Insert marker
Press OK
visible
Current chapter
Delete marker
Delete all markers
New index picture
Divide title
Changing the index picture
Normally the picture from the beginning of a recording is used as the
index picture. You can however choose any picture from the recording
as the index picture.
Press EDIT to exit
2 Select 'Divide title' and confirm with the OK button.
1 During playback, search for location of the new index picture.
Press the PAUSE 9 button.
3 If you are sure, press OK to start the process.
P 'Dividing title' appears on the TV screen.
2 Press the EDIT button.
P The 'Favorite Scene Selection' menu appears on the TV
screen.
4 Wait until the new title is displayed with an index picture in the
index picture overview.
The process of splitting the title is now complete.
Favorite Scene Selection
Insert marker
Press OK
visible
Current chapter
Delete marker
Delete all markers
New index picture
Divide title
Press EDIT to exit
3 Select line 'New index picture' and confirm with OK .
4 Start the change with OK .
P 'Updating menu' appears on the TV screen.
Once the revision has been completed successfully the DVD recorder
reverts to the index overview.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing the disc contents
Editing recording titles (name)
Playing the entire title
1 If required, press the STOP h button to interrupt playback.
If you have hidden certain sections (chapters) of a title, this setting lets
you watch the entire title including the hidden sections. To do this,
proceed as follows:
2 Using A or B select the title whose name you want to edit and
confirm with C .
P The menu for editing names appears.
1 Press the STOP h button or during playback press DISC
MENU .
Settings for title Charly 1
Settings for title Charly 1
Name
Charly 1
Name
Charly 1
Play full title
Erase this title
Press OK
Play full title
Erase this title
3 Select 'Name' using A or B and confirm with C .
2 Using A or B select the title you want to play all of and confirm
with C .
4 Using C or D select the position where the letter/number/icon
is to be changed/re-entered.
P The title editing menu will appear.
5 Change the icon using A or B .
3 Select 'Play full title' using A or B and confirm with OK .
O You can switch between upper and lowercase using
SELECT .
P Playback starts automatically. The title is played in its entirety -
including the hidden chapters.
O You can delete the character using the red function button.
How can I enter the characters with the buttons 0..9 ?
Press a number button as often as the required character or the
number appears. You can enter language dependent characters with
the buttons N or O on the corresponding character e.g.: ä,
button 2 for 'a' and then with O as often as 'ä' appears.
For special characters press the button 1 repeatedly.
The position for the following character will be selected automatically.
To enter a space press the button 1 .
To erase a character press the red function button.
6 Repeat 4 and 5 until you have made the changes you want.
7 Save the new name with OK .
P 'Storing name' appears on the TV screen for confirmation.
8 To end, press D .
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing the disc contents
Disc settings
Erasing recordings/titles
You can erase specific recordings from a disc.
Please note: If there is an 'Empty title' between titles, this space can
not be used from this DVD-Recorder.
Each recording from the HDD to a DVD+RW/+R (archiving) will be
added at the end of existing recordings
Philips1
00:35:59 used
Fri15/02/2003
PAL
1 Press the STOP h button or during playback press DISC
DVD playback
MENU .
2 Using A or B select the title you want to delete and confirm
with C .
P The title editing menu will appear.
This screen appears before the first title and contains general
information about the current disc.
Settings for title Charly 1
You can:
Name
Charly 1
•) change the name of the disc
•) activate or deactivate write protection on the disc
•) Finish editing (make the disc DVD compatible)
•) finalise a DVD+R
Play full title
Erase this title
Press OK
•) delete a DVD+RW
To get to this display, proceed as follows:
1 Press the STOP h button or during playback press DISC
MENU .
3 Select 'Erase this title' using A or B and confirm with OK .
P 'This will completely erase this title'. 'Press OK to
confirm' appears on the TV screen.
2 Select the first title with A or press STOP h . STOP h .
3 Press A .
O If you want to delete this title, press OK to confirm.
P The disc info display will appear.
O Otherwise press D .
4 'Erasing title' appears on the TV screen.
Changing the disc name
5 At this point 'Empty title' appears in the 'index picture display'. A
1 In the 'Disc info display' press C .
new recording can now be made here.
P The 'Settings for' menu appears on the TV screen.
If the deleted title was very short (less than 1 minute) 'Empty
title' will not appear at this point.
Can titles be deleted from a DVD+R disc?
Settings for Philips1
Titles on DVD+R discs are only marked as deleted. 'Deletedtitle ' will
appear in the display instead of 'Empty title'. During playback the
'deleted' title is skipped. The space used for this title cannot be used
again as the title has not been physically deleted. Once the disc has
been finalised no further changes can be made.
Disc name
Protection
Erase disc
Philips1
Unprotected
2 Select 'Disc name' using A or B and confirm with C .
3 Using C or D select the position where the letter/number/icon
is to be changed/re-entered.
4 Change the icon using A or B .
O You can switch between upper and lowercase using
SELECT .
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing the disc contents
O You can delete the character using the red function button.
Finalising DVD+R discs
This feature is required to play back a DVD+R disc in a DVD player.
Once the disc has been finalised no further recordings or changes can
be made.
5 Repeat 3 and 4 until you have made the changes you want.
6 Save the new title with OK .
P 'Storing name' appears on the TV screen for confirmation.
1 In the 'Disc info display' press C .
P The 'Settings for' menu appears on the TV screen.
7 To end, press D .
2 Select 'Finalise disc' using A or B and confirm with OK .
Finishing editing
a 'Finalise disc' does not appear
If one or more titles have been edited a DVD player may still display
the original titles. You can prepare your DVD+RW disc in such a way
that a DVD player will be able to play the edited version.
b Either there is no DVD+R disc inserted or the disc is already finalised.
To end, press SYSTEM MENU .
a The 'Settings for' menu does not appear
b The menu may not appear if the disc has been recorded on another
DVD recorder. In this case, use the 'Finalise disc' feature in the
1 In the 'Disc info display' press C .
P The 'Settings for' menu appears on the TV screen.
'
' menu, under 'Features'.
A
3 The screen displays 'This will take...' to show how long the
2 Select 'Make edits compatible' using A or B and confirm
process will take.
with OK .
4 To confirm press OK .
a 'Make edits compatible' does not appear
b Your disc is already compatible. There is no need for conversion.
To end, press SYSTEM MENU .
P 'Working...' appears on the TV screen.
P A bar will move from left to right indicating progress.
3 The screen displays 'This will take' to show how long the
process will last.
Erasing DVD+RW Disc's
4 To confirm press OK .
P 'Working...' appears on the TV screen.
1 In the 'Disc info display' press C .
P The 'Settings for' menu appears on the TV screen.
P bar will move from left to right indicating progress.
Settings for Philips1
Disc name
Protection
Erase disc
Philips1
Unprotected
Press OK
2 Select 'Erase disc' using A or B and confirm with OK .
P 'This will erase all titles Press OK to confirm' appears
on the TV screen..
3 If you want to delete all the titles, press OK to confirm.
Otherwise press D .
P 'Erasing disc' appears on the TV screen.
After deletion, the index picture display shows the free space
on the disc.
If the disc is empty already, you cannot select 'Erase disc'.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Manager (DM)
General information
Adding a disc tothe Disc Manager
The 'Disc Manager' is an integrated database in the DVD recorder that
remembers all recordings on DVD+RW/+R discs made by this DVD
recorder. This gives you a complete overview of your entire video
collection at the touch of a button. The Disc Manager gives you quick
and easy access to every recording made on with this DVD
recorder. The Disc Manager also tells you which film was recorded on
which disc and how many unrecorded minutes remain on the discs.
And: You can go automatically to the beginning of the selected
recording and start playback.
You can only add DVD+RW or DVD+R discs to the Disc Manager
since other discs do not hold any information on the titles or lengths of
the recordings. These discs have to be at least once recorded in the
DVD-Recorder. A table of content have to be available.
DVD+R discs can also be finalised. Other discs cannot be added to the
Disc Manager.
Recordings are saved automatically
On a disc that has been added to the Disc Manager, you can make new
recordings as often as you like using this DVD recorder. The titles of these
recordings will be stored in the Disc Manager automatically.
How many discs can I save in the Disc Manager?
You can store up to 999 discs on this DVD recorder. The maximum number
of titles is more than 9,000. The maximum number of titles per disc is 49.
Preparation:
•) The TV set is switched on, and if necessary, the programme number for the DVD
recorder has been selected.
•) the DVD recorder is switched on.
Caution when recording with other DVD recorders
Don't use a disc stored in the Disc Manager for recording on other DVD
recorders. If you use a disc to record on another DVD recorder, then this
disc will no longer be recognised by the Disc Manager. In this case, delete
the disc from the Disc Manager's memory and then add it after it has been
recorded.
1 Insert the DVD+RW/+R disc that you want to add in the DVD
recorder.
Adding 'child-proof discs'
Disc Manager
If you want to add child-proof discs you need to enter the PIN code.
Find title
C04
Browse discs
Remove a disc
Add current disc
Disc number001
Disc number001
Next free disc number= 001
To exit press DM
a When I insert a disc I see a number on the screen in the
index picture screen in the top left-hand corner
b You have inserted a disc that has already been registered by the Disc
Manager.
2 Press the DISC MANAGER button on the remote control.
3 Select 'Add current disc' using A or B and confirm with C .
4 Confirm with OK .
P The disc number will be added to the Disc Manager.
P The disc number is then displayed and the disc tray opens
automatically.
The disc is now stored in the Disc Manager under the
displayed disc number.
Please write this number on the disc and on the cover.
Why do I need to label the discs?
When searching for unrecorded free space or available recordings, you
will asked to insert the appropriate discs (disc numbers).
5 To end, press DISC MANAGER .
The DVD recorder will immediately recognise that this disc is saved in
the Disc Manager. When this disc is inserted the disc number will
appear in the title overview in the top left-hand corner.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Manager (DM)
What do the displays on the screen mean?
Removing discs from the Disc Manager
'Title' = Title
'Date' = Date of the recording
'Duration' = Length of the recording
Every DVD+RW/+R is stored with a number in the Disc Manager
(DM). You can remove this disc number from the Disc Manager to use
the Disc Manager's memory for new discs or to remove damaged discs
from memory.
3 Select the title that you want to play back with B or A .
4 Confirm with OK .
1 Press DISC MANAGER on the remote control.
P The DVD recorder will jump to the start of the selected
2 Select 'Remove a disc' using A or B and confirm with C .
recording.
a I see the message 'Insert disc number' on my screen
b The selected recording is located on the Disc Manager disc with the
displayed disc number. Please insert the appropriate disc. After a
brief check, the DVD recorder will jump to the start of the selected
recording.
Disc Manager
Find title
C04
Browse discs
Remove a disc
Add current disc
Disc number001
Disc number001
Next free disc number= 001
Searching discs
To exit press DM
You can easily search for the title of a recording stored in the Disc
Manager. To do this, the appropriate disc does not have to be in the
DVD recorder.
3 Select the disc number with A or B and confirm with OK .
1 Press DISC MANAGER on the remote control.
Disc contents are not deleted.
2 Select 'Browse discs' using B or A .
The disc is only removed from the Disc Manager's memory. Its contents
remain unchanged.
3 Confirm with C .
P The screen will show the contents of the last Disc Manager
4 To end, press DISC MANAGER .
disc used.
Searching for a title in the Disc
Manager
Disc Manager
Disc number
001
Browse discs
This function can be used to quickly and easily find and play back a
recording saved in the Disc Manager.
Title
Date
Duration
Charly 1
01.01.200400:28
1 Press DISC MANAGER on the remote control.
2 Select 'Findtitle ' using B or A and confirm with C .
P A list of the titles of all recordings stored in the Disc Manager
(DM) will appear on the TV screen.
Page1/1
To select title press OK
4 Use A or B to select a different disc number if necessary and
confirm with C .
Disc Manager
What do the displays on the screen mean?
Find title
Title
Date
Duration
Charly 1
01.01.200400:28
'Title' = Title
'Date' = Date of the recording
'Duration' = Length of the recording
5 Press A or B to select the desired title.
Page1/1
To select title press OK
6 Confirm with OK .
P The DVD recorder searches for the start of the appropriate
recording.
a I see the message 'Insert disc number' on my screen
b The selected recording is located on the Disc Manager disc with the
displayed disc number. Please insert the appropriate disc.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
User preferences for the HDD
Toolbar
General
This section describes how you can adjust the functions of the HDD to
your personal preferences.
SYSTEMMENU
Options
When you press SYSTEM MENU , a so-called puck 'Z' appears on a
line.
Toolbar
Audio
If there are further selection options within a line, an arrow e.g.: 'S'. will
appear in the respective segments e.g.: 'W'. Using the corresponding
buttons on the remote control (e.g. C ) you can call up further
features or selection options.
Zoom
Time search
Subpictures
Preparation:
•) Switch on the TV set and, if necessary, select the programme number for the
DVD recorder.
•)Switch on the DVD recorder.
1 Press TUNER on the remote control to switch to HDD mode.
Options
You can also switch to HDD mode by pressing BROWSER
HDD but you will not see the picture of the currently selected TV
channel as a background picture.
In this menu, you can choose functions for the playback of recordings
(titles) on the HDD:
'Audio'
2 Press SYSTEM MENU on the remote control
Selection of the language for the TV show currently selected on the
DVD recorder.
P The system menu for the HDD appears.
'Lang I' or 'Lang II' in the display also indicates whether a TV show is
broadcast in two languages. This setting only affects playback through
the internal tuner of the DVD recorder. The setting for the
programmed recording (Timer) will not be affected.
If you also want to use/change the language for the programmed
recording, you must change the language in the 'Preferences' menu
(setting 'Language').
SYSTEMMENU
Options
Toolbar
Preferences
Set up
O 'Lang. I'
Playback is carried out in the original or main language.
'Lang I' also appears in the display.
O 'Lang.II'
Playback is carried out in the dubbed language available.
'Lang II' appears in the display.
3 Select the corresponding line using B or A .
O If the arrow C in the puck 'Z' is visible in one of the lines,
you can select additional functions with C on the remote
control.
'Zoom'
Using this function, you can enlarge (blue function button) or reduce
the size (yellow function button) of the still picture or pan through the
enlarged picture using B , A , D , C during playback from the
HDD (time shift buffer or media browser).
O To return to the previous menu, keep pressing A until the
top menu item is selected.
Press D to return to the previous menu item.
Press the red function button to stop this function.
4 Select the corresponding function using B or A , or the setting
with D or C . Select the functions you want to change as
described in the following pages.
'Time search'
Using this feature, you can search a position by time. You can use this
feature both for titles in the media browser and for playback from the
time shift buffer.
5 Confirm the new setting with OK .
6 Close the menu item with D .
'Subpictures'
This function is only required if recordings were made through a video
camera connected to the DV IN (CAM2) socket. In this case, you can
display/hide information on the date and time of the recording.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
User preferences for the HDD
O 'M4'
Preferences
Extended Play (better than VHS picture quality).
Recording time of:
DVD+RW/+R: 4 hours.
HDD: approx. 64 hours
SYSTEMMENU
Recording
Preferences
O 'M6'
Record mode
Camera mode
Chapters
Super Long Play (VHS-picture quality).
Recording time of:
DVD+RW/+R: 6 hours.
HDD: approx. 96 hours if the average recording time for a
title is at least 20 minutes.
HDD buffer
Language
O 'M8'
Super Extendend Play (VHS-LP-picture quality).
Recording time of:
DVD+RW/+R: 8 hours.
HDD: approx. 130 hours if the average recording time for a
title is at least 20 minutes.
Sat record
Direct rec.
Filter
Safety Slot
'Camera mode'
Select the recording mode (picture quality for recording) from one of
the displayed settings for the recording from external sockets. M1,
M2x, M3,... M8. Read the previous section (Record Mode) on the
picture quality that corresponds to each setting.
Recording
In this menu, you can select one of the following functions for
recording:
'Chapters'
O 'Off'
I can not select some functions
No auto chapters
During a recording the selection of some functions are not possible. e.g.
'HDD buffer'.
O 'On'
Automatic chapter marking after 5 minutes.
'Recordmode '
'HDD buffer'
Select from the settings displayed the record mode (picture quality of
the recording). M1, M2x, M3,... M8.
Choose one the displayed settings to define how long a recording will
be kept stored.
For recordings on a DVD+RW/+R (archiving function) always the
recording mode used for the recording on the HDD will be taken.
Observe the maximum possible recording time on a DVD+RW/+R.
The maximum possible recording time on the HDD depends from the
recording mode and the average length of the recordings (titles).
O '1h'
The recording will be kept stored for 1 hour
O '6h'
The recording will be kept stored for 6 hours
O 'M1'
High Quality (high recording quality)
offers the best picture quality and a recording time of:
DVD+RW/+R: 1 hour.
'Language'
Here you can set the default language to be used for the programmed
recording of bilingual TV shows. You can no longer change the language
once playback has started.
HDD: approx. 16 hours
O 'M2'
Standard Play (pre-recorded DVD quality)
offers standard picture quality and a recording time of:
DVD+RW/+R: 2 hours.
O 'Lang. I'
Recording is carried out in the standard language.
O 'Lang.II'
HDD: approx. 32 hours
Recording is carried out in the dubbed language available.
O 'M2x'
Standard Play plus (better than S-VHS quality)
offers standard picture quality and a recording time of:
DVD+RW/+R: 2,5 hours.
'Sat record'
If a video signal is detected at the EXT2 AUX-I/O scart socket,
recording will begin.
HDD: approx. 40 hours
O 'On':
O 'M3'
Sat Record is activated.
Long Play (S-VHS picture quality).
Recording time of:
DVD+RW/+R: 3 hours.
HDD: approx. 48 hours
O 'Off':
Sat Record is deactivated.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
User preferences for the HDD
'Direct rec.'
'Set up'
If a recording starts while the DVD recorder is switched off, the TV
channel currently selected on the TV set will be compared with the TV
channels stored in the DVD recorder.
SYSTEMMENU
System
- If the TV channel is found, recording will start.
- If the TV channel is not found, a message will appear on the screen
and in the display.
Set up
Auto delete
Jump forward
Jump back
Installation
Flush Buffer
O 'On':
Direct Record is activated.
O 'Off':
Direct Record is deactivated.
'Filter'
Here you can choose between:
'System'
I can not select this function
In this menu, you can select one of the following features:
Check the actual record mode selected. This function is available in the
record modes 'M4' to 'M8' only.
'Auto delete'
O 'Sport':
If there is no space for new recordings on the HDD, you can
determine here whether recordings will be automatically deleted or
not. You can see the titles and the sequence according to which they
will be deleted in the 'Delete Order' setting in the media browser. For
more information, read the chapter 'The Media Browser'.
Picture quality is optimised for rapid movements in the
recording modes (picture qualities) M4 to M8.
Please observe that this setting will reduce the overall
impression of the picture quality.
O 'Normal':
O 'On':
Better overall picture quality.
Recordings will be automatically deleted in the following
order:
1) Titles that have already been viewed. Symbol 'E'.
2) Titles that were not protected. No symbol 'F' available.
Please observe that this setting may cause picture artefacts
(MPEG artefacts) to appear in rapid movements.
'Safety Slot'
O 'Off':
Here you can enter a time (one to five minutes) when a programmed
recording (Timer) should start earlier and end later. This could be
necessary if the information from the GUIDE Plus+® system about the
start and stop time always differ from the actual start and stop time.
No recordings will be automatically deleted.
'Jump forward'
Set the time you want to jump forward when you press JUMP
FWD in the time shift buffer.
'Jump back'
Set the time you want to jump backward when you press JUMP
BACK in the time shift buffer.
Use the setting 5 minutes for Jump forwardand 1 minute for
'Jump back', to make it easy to skip unwanted scenes.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
User preferences for the HDD
'Installation'
Please observe that for selection of function in this menu the Time shift
Buffer will be flushed. If the 'Time Shift Buffer ' contains important
recordings, save them with the REC/OTR n button first. Read
additional information about the 'Time Shift Buffer' in the chapter 'The
Time Shift Buffer'.
O 'Autom. search':
Automatic channel search
O 'Follow TV':
Sorting TV channels automatically
O 'Manual search':
Manual TV channel search
O 'Sort TV channels':
Sorting TV channels manually
O 'Time/Date':
Setting/Correcting the time and date
For more information, please read chapter 'Additional installation
features'.
'Flush Buffer'
Using this function, you can store recordings on the HDD that were
marked for recording in the time shift buffer. Recordings that were not
marked will be deleted.
O 'Yes':
Recordings will be stored
O 'No':
This interrupts the process
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional user preferences
General
Picture settings
This section describes how you can make additional personal settings.
The symbols have the following meaning:
You can select the following functions in this menu:
Picture settings
t
Sound settings
v
Language settings
u
Picture
TV shape
16:9
Off
Additional settings
w
Black level shift
Video shift
ï
Disc settings
SCART video
RGB
s
Preparation:
•) The TV set is switched on, and if necessary, the programme number for
the DVD recorder has been selected.
•) the DVD recorder is switched on.
'TV shape'
The picture signal from your DVD recorder can be set to match your
TV set:
1 Press the DISC MENU button and then the SYSTEM
MENU button on the remote control.
P The menubar appears.
O '4:3 letterbox'
for a widescreen picture with black bars at the top and
bottom
O '4:3 panscan'
If this menubar is not complete visible on your wide screen TV-set,
change the picture settings on your TV.
for a full-height picture with the sides trimmed.
O '16:9'
2 Select ' ' using D oder C and confirm with
A
for a widescreen TV set (16:9 screen ratio)
3 Select the corresponding function using B or A and confirm
with C .
'Black level shift'
4 Select the corresponding line using B or A and confirm with
C . For more information on each function, read the following
pages.
Adapts the colour dynamics for NTSC playback when switched to 'On'
'Video shift'
5 Select the corresponding function using B or A , or the setting
with D or C . Select the functions you want to change as
described in the following pages.
Use this feature to adjust the position of the picture on your TV left or
right using D , C to suit the screen of your TV set.
6 Confirm the new setting with OK .
'SCART video'
Since RGB and S-VIDEO signals sometimes use the same connections
on a scart cable, the two signals cannot be transmitted simultaneously.
With these settings, you can decide whether RGB or S-VIDEO signals
are to be transmitted. This setting affects only the scart sockets of the
DVD recorder ( EXT1 TO TV-I/O output socket and EXT2
AUX-I/O input socket).
7 Close the menu item with D .
Please also observe which signals are available at which scart socket of
the TV set or how the scart sockets need to be switched.
If necessary, consult the instruction manual of your TV set.
O 'RGB'
Depending on the TV set you are using, switching between the
'RGB' and the 'Video(CVBS/FBAS)' signal is done automatically.
If the picture scrolls to the side or colour quality problems
appear on some TV sets when the setting is 'RGB', you must
select 'CVBS only'.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional user preferences
O 'S-Video'
Only the S-Video signal will be processed at both scart sockets
Sound settings
( EXT1 TO TV-I/O output socket and EXT2 AUX-I/O input
socket).
You can select the settings in this menu depending on which audio
outputs are used.
If you only use the analogue audio output (red and white socket
AUDIO OUT L/R ), select the setting 'Off' in the 'Digital output'
menu.
In case the scart socket of the TV set is not suitable for
S-VIDEO (Y/C) signals, you will only see a black&white
picture, although the recording will be made in colour.
Moreover, only the video (CVBS, FBAS) signal will be used for
recordings via the EXT1 TO TV-I/O scart socket.
Please observe that when making recordings from a video
recorder that transmits only video (CVBS/FBAS) signals
through the scart cable, recordings via scart socket EXT2
AUX-I/O may be made in black and white.
Therefore, use this setting with caution.
Sound
Digital output
Analogue output
Night mode
All
O 'CVBS only'
Stereo
Off
Only the video (CVBS/FBAS) signal is transmitted, regardless
of the video signals (RGB, Y/C) at the scart sockets. This
setting is selected automatically when no 'RGB' or 'S-VIDEO'
signal is detected at the scart socket.
When selecting the settings 'S-Video' or 'CVBS only', the RGB signal
is switched off.
'Digital output'
You can select one of the following settings for devices that are
connected to the COAX OUT or OPTICAL OUT sockets:
The 'RGB' signal is switched off.
O 'S-video + YPbPr'
O 'All'
Component Video (YUV) and S-Video(Y/C).
GUIDE Plus+® menus only available on YUV ouput sockets.
Dolby Digital and DTS signals are fed unaltered to the digital
output. MPEG-2 multi-channel signals are converted to PCM
(Pulse Code Modulation).
For receivers/amplifiers with digital multi channel
decoders.
O 'CVBS + YPbPr'
Component Video (YUV) and Video (FBAS/CVBS).
GUIDE Plus+® menus only available on YUV ouput sockets.
O 'PCM only'
With all other settings, the signal is switched off at the
COMPONENT VIDEO OUT sockets. This will also be displayed
as information on the screen.
Digital and MPEG-2 multi-channel signals are converted to
PCM (Pulse Code Modulation). For receivers/amplifiers
without digital multi channel decoders.
O 'Off'
Digital output switched off.
For devices with analogue audio input.
'Analogue output'
You can select one of the following settings for devices that are
connected to the analogue audio output ():
O 'Stereo'
For devices without DolbySurround or TruSurround. Use this
setting if the DVD recorder is only connected to a stereo TV
set.
O 'Surround'
Dolby Digital and MPEG-2 multi-channel are mixed down to a
Dolby Surround-compatible two-channel output signal.
For devices with Dolby Surround / Pro Logic Decoder .
'Night mode'
Night mode optimises the sound for playback at low volume. You are
therefore less likely to disturb your neighbours. This only works with
Dolby Digital audio on DVD video discs.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional user preferences
Language settings
'Standby'
You can switch off the clock display on your DVD recorder to save
energy. Programmed recordings will be carried out despite of this.
In addition, you can have the most important features of your DVD
recorder appear in scrolling text in the display (demo).
You can select the following settings in this menu:
O 'Low power':
When the DVD recorder was switched off using
STANDBY m , the clock display is also switched off.
Language
O 'Normal':
Audio Language
Subtitle
English
English
English
When the DVD recorder was switched off using
STANDBY m , the clock display remains visible.
Menu
O 'Demo mode':
When the DVD recorder is switched off using
STANDBY m , a list of the most important features appears
in the display.
'Audio Language'
'Display'
Playback audio language.
You can change the brightness of the display on the DVD recorder.
This setting only affects the DVD recorder when it is switched on.
'Subtitle'
O 'Bright':
Subtitle language
The display appears with normal brightness. The disc tray light
is switched on.
'Menu'
O 'Dimmed':
Screen menu language
The display appears less bright. The disc tray light is switched
off.
Additional settings
O 'Off':
The display and the disc tray light are switched off.
You can select the following functions in this menu:
Features
Status box
Standby
Display
On
Normal
Bright
'Status box'
During play back from a disc, information of the current operating
status (counter, playback) will be shown on the TV screen.
You can switch off the information about the operating status so that
the on-screen display is not recorded when making recordings on
additional devices.
O 'On'
The OSD information appears for a few seconds in each
selected mode and then disappears.
O 'Off'
The OSD information is switched off. It is nolonger
displayed on the screen.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional user preferences
Disk feature menu
In this menu, you can make changes that relate to the disc:
Disc features
Access control
Auto resume
Enter code
On
'Access control'
Please read the next chapter 'Access control (child lock)'.
Auto resume
If playback of a pre-recorded DVD video disc or video CD is
interrupted (using STOP h or OPEN/CLOSE J ), playback will
resume where it stopped after you reinsert the disc. This applies not
only to the current disc but also to the last 20 discs you played.
You can switch off this feature if you do not want it.
'PBC'
This line appears only if you insert a VCD.
Using this function, you can activate or deactivate the PBC menu
(Playback Control) of a Video CD. For more information, read section
'Playing a (Super) Video CD' in chapter 'Playback'.
'Finalise disc'
This function allows you to finalise DVD+R discs. If the disc has already
been finalised, this line will appear darker.
'Adapt disc format'
If a DVD+RW has been recorded in a PC drive or a different DVD
recorder, the index screen may not be displayed properly.
This feature allows you to adjust the format of the disc.
Therefore, this feature is only visible if the disc format is different.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Access control (Child Lock)
8 Confirm with OK .
Child lock (DVD and VCD)
9 Quit the feature using D and SYSTEM MENU .
This feature enables discs to be locked for children.
When Child Lock is on, a 4-digit code (PIN) needs to be entered
before a disc can be played.
Unauthorised discs can only be played by entering the four-digit PIN
code.
You can also decide whether the inserted disc should always be played
or should be played only once, despite the child lock
To deactivate the child lock, select the ' ' icon in 7 .
n
•)'Play always':
Authorising a disc
This disc is stored in a memory with space for 50 child-safe discs. If
more than 50 discs are stored, the last disc in the list is removed and
the new disc is added. The screen shows 'Child safe' at the start of
playback.
1 Insert a disc. The access control box will appear after a short
delay.
2 Using A or B select 'Play once' or 'Play always'.
•)'Play once':
This disc is only authorised for single playback. If the recorder is
switched off, the PIN code must be re-entered.
3 Enter your PIN code using the number buttons 0..9 .
Double-sided DVDs may have a different ID for each side. For these
discs, each side must be authorised. Video CDs may have a different ID
for each disc. For these CDs, each disc must be authorised.
Activating/deactivating child lock
Preparation:
•) The TV set is switched on, and if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
Locking unlocked discs
To lock a disc that was formerly authorised follow the instructions
below
1 Press TUNER and then SYSTEM MENU on the remote
control. If playback from a disc starts automatically, remove the
disc (button OPEN/CLOSE J ).
1 Insert a disc. Playback starts automatically. If the playback does not
start automatically, press PLAY G .
P The menubar appears on the screen.
2 Press the STOP h button while the '
' icon is visible. The
'. The disc is now locked.
m
2 Select the ' ' icon using D or C .
A
icon changes to '
l
P The 'SYSTEM MENU' appears.
3 Select ' (Disc features)' using B or A and confirm with C .
s
Disc features
Access control
Auto resume
Enter code
On
4 Confirm 'Access control' using C .
5 Enter a 4-digit code of your choice.
This code will also be used for locking titles on the HDD (Media
Browser).
P If the code is new, you may have to enter the code a second
time as confirmation.
6 Select 'Childlock ' using A or B and confirm with C .
7 Select the ' ' icon using B or A .
i
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Access control (Child Lock)
What do the ratings mean?
Parental level control (DVD video
only)
Rating 0 (displayed as '--') parental control not active.
Rating 1 (suitable for children)
Rating 8 (only suitable for adults)
Films on pre-recorded DVD discs may contain scenes not suitable for
children. Therefore, some discs may contain 'Parental Control' rating
information that applies to the entire disc or to certain scenes on the
disc.
What happens if a DVD scene contains a higher level than
the rating set?
If the recorder does not find a suitable alternative, playback will stop
and you must enter the four-digit code.
The appropriate scenes have filter values that reach from 1-8. If such a
scene is detected during playback, the filter value set on the DVD
recorder is compared to the scene. If the filter value is higher than the
setting, an alternative scene will be played (if available).
Most DVDs apply the rating to an entire DVD. Therefore, if certain
scenes exceed the rating you select, the entire disc will be blocked
from viewing.
0 Confirm with OK . Quit using D and SYSTEM MENU .
Changing the country
The set filter values depend on the respective country. It is therefore
necessary to enter the country to which these filter values apply.
Activating/deactivating parental level control
Preparation:
•) The TV set is switched on, and if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
Preparation:
•) The TV set is switched on, and if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
1 Press the TUNER and then the SYSTEM MENU button on the
remote control.
1 Press DISC MENU and then SYSTEM MENU on the remote
P The menubar appears on the screen.
control.
P The menubar appears.
2 Select the ' ' icon using D or C .
A
2 Select the ' ' icon using D or C .
A
3 Select line ' (Disc features)' using B or A and confirm with
s
C .
3 Press the SYSTEM MENU button on the remote control.
4 Select the ' ' icon using D or C .
A
5 Select ' (Disc features)' using B or A and confirm with C .
s
Disc features
Access control
Auto resume
Enter code
On
Disc features
Access control
Auto resume
Enter code
On
4 Confirm the line 'Access control' using C .
5 Enter your four-digit code. If the code is new, you may have to
enter the code a second time as confirmation.
6 Confirm 'Access control' using C .
6 Select 'Change country' using B or A and confirm with C .
7 Enter a 4-digit code of your choice. If the code is new, you may
7 Select the corresponding country using A or B and confirm
have to enter the code a second time as confirmation.
with OK .
8 Select the 'Parental level' using A or B and confirm with C .
8 To end, press D and then SYSTEM MENU .
A bar appears to select the parental level.
9 Select the appropriate rating using B , A or the number buttons
0..9 .
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Access control (Child Lock)
Changing the PIN code
Preparation:
•) The TV set is switched on, and if necessary, the programme number for the
DVD recorder has been selected.
•) the DVD recorder is switched on.
1 Press the TUNER and then the SYSTEM MENU button on the
remote control.
P The menubar appears.
2 Select the ' ' icon using D or C .
A
3 Select ' (Disc features)' using B or A and confirm with C .
s
Disc features
Access control
Auto resume
Enter code
On
4 Confirm 'Access control' using C .
5 Enter your four-digit PIN code. If the code is new, you may have to
enter the code a second time as confirmation.
6 Select 'Change code' using A or B and confirm with C .
7 Enter the new code using the number buttons 0..9 . Enter the
same code again as confirmation.
8 Quit using D and SYSTEM MENU .
I have forgotten my code
Press STOP h four times (step 5 ), then press OK . Access
control is now switched off. You can now enter a new code as described
above.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Information on the screen of your TV
Repeat title
3
4
2
0
1
7
l
8
9
You can check or change many of the functions and settings of your
DVD recorder via the system menu bar.
Repeat track
Repeat chapter
Symbols in the menu bar
Repeat from A to the end
Repeat from A to B
Camera angle
Press DISC MENU and then SYSTEM MENU to open the menu
bar. If a disc is played back, you can open the menubar with SYSTEM
MENU .
Use D and C to select the relevant function.
Use B to confirm the function and go either to another menu or
execute the function directly.
Child lock enabled
Resume playback
Illegal action
Some functions may not be available, depending on the disc inserted.
Menu bar 1
Status field
User preferences
A
During playback of a disc, the status field shows the current operating
mode (status) of the DVD recorder and the type of disc inserted. This
display can be switched off.
Title/track
B
Chapter/index
C
Audiolanguage
D
Disc type symbols
Subtitle language
E
DVD+RW
M
W
N
O
P
Q
Camera angle
F
DVD+R
Zoom
G
DVD Video
Video CD
Nodisc
Menu bar 2
While menu bar 1 is being displayed you can go to menu bar 2 by
pressing C again.
Error
Operating mode symbols
Sound
H
Recording
R
Frame advance
I
Stop
S
Slow motion
J
Playback
T
Fast motion
K
Playback Pause
U
Search by time
L
Record Pause
V
Search forwards (8x speed)
X
Search backwards (8x speed)
Field for temporary messages
Y
Slow motion
Z
The top left corner of the menu line contains a field for temporary
messages relating to the various operating modes. This information
appears briefly on the screen when certain disc functions have been
activated:
Shuffle
/
Scan
6
Repeat entire disc
5
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Information on the screen of your TV
The symbols on your DVD recorder
display
Messages in the DVD recorder display
READING
These symbols can light up on your DVD recorder display:
The following messages may appear in your DVD recorder display
Multi-function display/text line
•) Clock
IS TV ON? The DVD recorder is in initial installation mode. Switch
the TV on, then read the paragraph on 'Initial installation' in
'Installing your DVD recorder'.
•) Disc/title playing time
•) Title name
NO SIGNAL No input signal available (signal inadequate or unstable)
MENU The menu on the screen is active
OPENING Disc tray opening
•) Display of the programme number of the TV channel/playing
time/channel name/function.
•) Display of information and alerts
•) Display of the title from the actual recording.
IIIIIIIIIIIIIII Position/Diskbar: Displays the current position on the
HDD/disc.
TRAY OPEN Disc tray open
Time Shift Buffer Displays the elapsed time. If all segments lits, the
oldest recording will be deleted from the Time Shift Buffer.
Play/Record: No segment will lit at the current position.
Pause: Flashing segment at the current position.
Stop: Nothing appears.
CLOSING Disc tray closing
READING Disc being read
MENU UPDT Once recording has been successfully completed the table
of contents is created.
SAT An automatic recording from a satellite receiver (SAT
INIT MENU The menu structure is created after the first recording has
recording) has been programmed.
been made on a new disc
TIMER A recording (timer) has been programmed
COPY PROT You received a copy-protected signal. This may come
from a copy-protected DVD/videotape of a DVD/video player or
from a TV channel.
o((( A remote control signal has been received
During the display COPY PROTno recording will be made. A
running recording will be interrupted.
VPS/PDC Video programming system / programme delivery control:
A VPS or PDC code is transmitted for the selected TV program
WAIT Please wait until this message disappears. The DVD recorder is
LANG II During playback a 2-channel tone was detected or a
2-channel tone was received. 'I' or 'II' lights up depending on which
sound channel has been selected
busy performing a task.
NO DISC A disc has not been inserted for recording. If a disc has been
inserted, it cannot be read.
INFO Information about the inserted DVD is displayed on the screen
BUSY The DVD recorder is processing the changes to make the disc
DVD compatible
ERASING The entire DVD+RW is being erased
EMPTYDISC The DVD+RW/+R inserted is either new or has been
completely erased (no recordings).
PROTECTED The DVD+RW/+R inserted is protected against recording.
How to remove this protection you will read in the section
'Protect disc against accidental recordings' in the chapter
'Recording on a DVD+RW/+R' .
MAX TITLE The maximum number of titles per disc/HDD has been
reached. The maximum number of titles on a disc is 48 and on the
HDD 499.
MAX CHAP The maximum number of chapters within a title/or the disc
has been reached. The maximum number of chapters is;
DVD+RW/+R: within a title 99, on the disc 255 (spreaded over
the whole disc)
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Information on the screen of your TV
HDD: within a title 500, on the HDD 1000 (spreaded over the
whole HDD)
DISC FULL The disc/HDD is full. There is no space for new recordings
PAL DISC A disc with PAL recordings has been inserted. The machine
is trying to record an NTSC signal. Insert a new disc or one that
contains NTSC recordings.
NTSC DISC A disc with NTSC recordings has been inserted. The
machine is trying to record a PAL signal. Insert a new disc or one
that contains PAL recordings.
RECORDING An illegal action (e.g. OPEN/CLOSE J button) was
attempted during recording on a DVD+RW/+R (archiving).
FREETITLE An empty title on a DVD+RW/+R is selected.
DISC LOCK An attempt has been made to record during playback of a
protected disc. This message appears if an attempt is made to
insert a chapter marker on this inserted DVD+RW/+R.
DISC ERR An error occurred when reading the title from a
DVD+RW/+R. If this error keeps occurring, please clean the disc
or use a new one. For instructions on how to clean a disc see the
section on 'Cleaning the discs' in the next chapter.
DISC WARN An error occurred when writing the title on a
DVD+RW/+R. Recording was continued; the error was skipped
SETUP After the automatic search the menu for setting the date/time
will appear on the screen.
WAIT 01 During the automatic channel search the TV channels found
will be counted.
BLOCKED The disc tray cannot be closed/opened.
SAFE REC During the archiving procedure, the new recording will be
added at the end of all the other recordings (SAFE RECORD).
POST-FORMAT After the creation of the menu structure the
DVD+RW/+R is prepared
PHILIPS The DVD-Recorder has been switched on
STANDBY The DVD-Recorder has been switched off
GUIDE The GUIDE Plus+® system is switched on
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call an engineer
If you have any problems using this DVD recorder, the reason may be one of the following. You can
also call the customer service centre in your country.
The telephone numbers can be found on the back of this instruction manual.
You can also visit our web page 'http://www.p4c.philips.com' .
Have the model number (MODEL NO) and the production number (PROD.NO) of your recorder
ready.
The production number (PROD. NO.) is printed on the type plate at the back or on the bottom
PROBLEM
SOLUTION
Your recorder does
not respond to any
button being pressed
and the display shows
'PHILIPS', 'IS TV ON?':
bRecorder in initial installation mode: Switch on the TV, switch over to the DVD recorder socket.
Now the menu for language selection should appear. Please read paragraph 'Initial Installation' in the chapter
'Installing your DVD Recorder'.
b'Dealer-Mode' is switched on: All buttons on the front of the set are locked.
Switch off the function:
The device does not
react when you press a
button, although the
remote control works:
1 Pull out the mains plug from the wall outlet.
2 Press and hold down h and OPEN/CLOSE J and put back the mains plug into the wall
outlet.
3 As soon as the time or '--:--' appears in the display (ca. 6 - 10 seconds), release h and
OPEN/CLOSE J .
Your DVD recorder
does not respond to
any button being
pressed:
bThere is no power supply: check the power supply
bThere is a technical problem: disconnect from the mains power supply for 30 seconds, then connect again.
If this doesn't help, you can reset your DVD recorder to the default factory settings.
bImportant:
All the information stored (TV channels, time and date, TIMER) will be lost.
1 Disconnect from the mains power supply.
Resetting the machine
tothe default factory
settings
2 Press and hold down the STANDBY-ON m button on the device and reconnect to the
mains power supply.
3 Release the STANDBY-ON m button when the features appears on the display. All the
information stored (TV channels, time and date, TIMER) will be lost.
Please read paragraph 'Initial Installation' in the chapter 'Installing your DVD Recorder'.
bRemote control not pointed toward the DVD recorder: Point the remote control at the machine. See if the
'o(((' appears on the display briefly each time you press a remote control button. If it does, the Recorder is
receiving information from the remote correctly.
bThere is a technical problem: Take out the batteries, wait for 10 seconds and put them in again.
bBatteries are flat: Change the batteries.
Remote control does
not work:
I can not switch off the
DVD Recorder:
bA recording is in progress (red light around the REC/OTR n button is switched on). After the recording is
finished, the DVD-recorder will switch off automatically.
bFor the execution of certain procedures the DVD recorder can switch itself on automatically, although no
Fans run with switched
off DVD recorder:
information is visible on the display. To prevent overheating, the fans at the back will be switched on and off
automatically
This is no foult of your set.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call an engineer
PROBLEM
SOLUTION
bThere is no recording on the HDD/disc: Check the titles from the HDD in the media browser (button
BROWSER HDD ), change disc.
bYou inserted the wrong disc type: Your recorder can play back the following disc types: DVD Video,
(Super)Video CD, DVD+R(W), Audio CD, , MP3-CD's
bYou inserted the disc the wrong way: Insert the disc with the label facing upwards
bDisc is dirty: Clean the disc
bWrong region code: The region code of the DVD and the DVD recorder must match.
bParental control is on: Read chapter 'Access control (child lock)'
Noplayback on DVD
recorder:
bParental control is on fro titles from the HDD: Read chapter 'Access control (child lock)'
bYou have selected the wrong programme number for the DVD recorder on the TV: on the TV, select the
correct programme number for the DVD recorder.
bThe cable connecting the TV set and the DVD recorder has come loose: check the cable.
bIt is possible that this (Super) Video CD contains a menu and the 'PBC' is switched off. You can see this in
status field 'PBC OFF'. To activate this function, proceed as follows:
1 Press SYSTEM MENU while the (Super) Video-CD is inserted .
2 Select ' ' using D or C .
3 Select line 'Features' using B or A and confirm with C .
4 Select 'On' in line 'PBC' using B or A .
A
I cannot playback
(Super) VideoCDs
5 Confirm with OK and end with SYSTEM MENU .
bCheck the format of self recorded (s)VCD's (1.0, 1.1, 2.0). Play back of (S)VCD's in a different format can be
distorted.
Poor playback on DVD
recorder: (distorted
picture/distorted
sound)
bYour TV set is not properly adjusted.
bDisc is dirty: Clean the disc
bSometimes the picture may be temporarily distorted. This is not a defect of your DVD recorder.
bThe low quality of some digital picture material may be the cause of digital image distortion. In this case
change the setting of the sharpness or the picture settings.
If your TV is equipped with a 'Smart picture' function, select the 'Soft' setting, without changing the picture
settings manually.
Digital distortions
No recording on the
HDD possible:
bThe TV channel you want to record is not stored or you selected the wrong programme number: Check TV
channels stored.
bDisc write-protected (recording protected): Remove write-protection or change the disc. For more information,
please see 'Preventing accidental erasing of discs' in chapter 'Manual Recording'.
bAn already finalised DVD+R has been inserted: Change disc.
No recording on the a
DVD+RW/+R possible:
bYou have programmed the wrong time or date: Check time/date.
bIf the time and date are wrong despite setting them by hand, you can switch 'SMART CLOCK' (Clock
preset) off. See 'Setting the time/date' in 'Installing your DVD recorder'.
bYou have not set the TIMER properly: Check the programmed recordings (TIMER block).
b'VPS/PDC' switched on but 'VPS/PDCtime' wrong: 'Enter 'VPS/PDCtime exactly to the minute. Check the
aerial.
Programmed
recording does not
work:
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call an engineer
PROBLEM
SOLUTION
bThe programme number of the TV channel is not available in the GUIDE Plus+® system or allocation is
wrong.
To change or check the channel data, proceed as follows:
1 Press GUIDE/TV .
2 Press A .
3 Select 'Editor' with C .
4 Select the TV channel using B or A .
The wrong TV channel
was decoded
(recorded) after you
programmed a
recording using
ShowView System.
5 Press C to go to the right tile.
In case you can receive the selected channel only via an external receiver, press the red
button to select the corresponding source.
6 Press the green button.
7 Enter the programme number of the TV channel using the number buttons.
If the source you have selected is an external receiver, enter the programme number that you
would also enter at the external receiver for this TV channel.
8 Confirm with OK .
bDVD recorder is switched on: Switch off the DVD recorder to allow data transfer
bThe TV channel that transmits the GUIDE Plus+® data is not set properly.
bExternal receiver (satellite receiver, set-top box, cable TV box, ...) (if available) is switched off: switch on the
external receiver
bG-LINK cable is not connected: Connect the G-LINK cable and make the necessary settings to control the
external receiver (see chapter 'The GUIDE Plus+® system', section 'Installation of the 'External receiver
1'').
There is nochannel
overview in the GUIDE
®
Plus+ system
Missing or wrong TV
channel in the 'Grid'
screen
bWrong local post code/country was entered
bPlease check your correct channel line up in the 'Grid' screen.
Read therefore the section 'The 'Editor' screen.
bThe GUIDE Plus+® system was not completely installed or local post code was not entered.
1 Check the settings
When you press
GUIDE/TV the GUIDE
2 Select the corresponding line using B or A and confirm with OK .
®
Plus+ setup screen will
3 For more information on the individual functions, see chapter 'The GUIDE Plus+® system',
section 'Setting up the GUIDE Plus+® System'.
appear
The external receiver
does not always react
to Remote control
signal.
bThe Infrared (IR) Remote control signal interfere with the IR signal of the G-LINK transmitter.
Put the G-LINK transmitter closer to the front of the external receiver.
My external receiver
switches automatically
through the TV
channels
bIf the DVD-Recorder is switched off ( STANDBY m button) the external receiver will be used from the
GUIDE Plus+® system via the DVD-Recorder.
If you want to watch TV-Channels from the external receiver, you have to switch the DVD-Recorder on.
bBefore recording, select the recording mode as described in chapter 'Manual Recording', section 'Selecting the
recording mode (quality)'.
bHave your aerial checked.
bYou will find information on how to change the TV system in 'Manual TV channel search' in 'Installing your
There is picture or
sound interference on
TV reception:
DVD recorder'.
Distorted sound
coming from a
connected hi fi
amplifier
bThe DVD recorder is connected to the 'Phono-input' of your amplifier: This socket is provided only for a record
players without a preamplifier. Select a different audio input.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call an engineer
PROBLEM
SOLUTION
The picture is
distorted or
black and white during
playback
bThe TV system of the disc does not match that of your TV set (PAL/NTSC).
bThe recording can be made in colour only when the TV channels or the connected additional device send a
colour signal. Black-and-white signals containing no color information (colour subcarriers) cannot be recorded.
Nosound signal at the
digital output
bCheck whether the sound settings match the selected inputs and connected additional devices. For more
information, see section 'Sound setting' in chapter 'User preferences'.
There could be
difference in the
search speed of a DVD
and DVD+RW
bDepending on the different structure of a DVD and a DVD+RW/+R this can lead to the different search
speeds. This is not a fault in your machine.
bIf a recording is too short, it is possible that a DVD player cannot detect it: Please observe the following
'Minimum recording times':
Recording mode 'M1': 5 minutes, 'M2': 10 minutes, 'M2x': 13 minutes, 'M3': 15 minutes, 'M4': 20 minutes,
'M6': 30 minutes, 'M8': 30minutes,
bSome DVD players cannot play back DVD+RW recordings. You can solve this problem by using a special
function:
1 Open the disc tray with OPEN/CLOSE J . Insert the disc but do not close the tray.
A DVD+RW disc
cannot be played on
certain DVD players
2 Hold down the number button 2 on the remote control until the tray closes. The disc is
modified.
3 If this fails to produce the desired result, repeat the procedure using the number button 3 on
the remote control.
4 You can restore the disc to its original condition by pressing 1 .
Warning!
There is a risk that you can no longer play the disc on other DVD players after this procedure.
Therefore, apply this function with particular care.
bIf it is impossible to play back a disc, you can try and repair it for new recordings using the following function.
This will only prepare the disc for erasing. It will not be erased, however, until the recording has been
completed.
1 Clean the disc
Other disc errors
(DVD+RW)
2 Open the disc tray with OPEN/CLOSE J . Insert the disc but do not close the tray.
3 Hold down the red function button on the remote control until the tray closes. The disc is
prepared for erasing.
4 Start recording as with an empty disc.
bThis message may appear if you instert a DVD+R that was not finalised or an error occurs during the
recording. DVD+R's that have not been finalised are very sensitive to fingerprints, dust, or dirt. This may
cause problems during recording.
To use the disc again, follow the next steps
1 Make sure that the surface of the disc is clean.
Other disc errors
(DVD+R), 'Disc
contains unknown
data' interruption of a
recording (power
outage)
2 Open the disc tray with OPEN/CLOSE J . Insert the defect DVD+R but do not close
the tray.
3 Hold down 5 on the remote control until the tray closes. The disc will be read ('READING'
appears on the display) and the DVD recorder will start the repair process. This may take up
to four times as much time as the recording, in which the error occurred.
4 If the disc is recovered, the index screen will appear.
Please observe the following:
The recovering procedure is successfully only if there was a previous recording on the disc.
Error during recording: The title may be missing.
Error while changing the title/index picture: The original title/index picture may be visible.
Error while finalising: The disc appears not to have been finalised.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call an engineer
PROBLEM
SOLUTION
bYou can finalise the disc using the following function:
1 Open the disc tray with OPEN/CLOSE J . Insert the defect DVD+R but do not close
The index screen
flickers when a DVD+R
is inserted
the tray.
2 Hold down 4 on the remote control until the tray closes.
'FINALIZE' appears in the display. Finalising begins. This may take up to three minutes.
3 If finalising has been successful, the index screen will appear.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossar
Chapters
Also known as 'scenes', a DVD movie can be broken up into sections
much like the chapters of a book, that can be accessed quickly and
easily via the DVD menu or remote control.
Component Video (Y Pb Pr)
This method of transmitting pictures produces the highest quality as
the video signal is split into its Y (brightness), U and V (blue minus
brightness, red minus brightness) components. The signals are
transmitted via separate cables. The plugs on these cables and the
associated sockets are mostly coloured red, green and blue.
NICAM
NICAM is a digital sound transmission system. Using NICAM, you can
transmit either 1 stereo channel or 2 separate mono channels.
However, if reception is poor and the sound distorted you can turn off
NICAM.
NTSC
National Television Systems Committee. The colour TV broadcast
system used in the US, Canada and Japan. An NTSC picture is made up
of 525 horizontal lines and has inferior picture quality in comparison to
the PAL system. All Australian-sold DVD players are NTSC compatible,
however DVD's that are played on a television that is not compatible
will appear in black and white.
PAL
Phase Alternating Line. The colour TV broadcast system used in
Australia, UK & Europe. A PAL picture delivers a better quality picture
than NTSC due to its 625 horizontal lines (sharper picture and better
colours).
Region code
Since DVD films are not normally released in all parts of the world at
the same time, all DVD players have a specific regional code. Discs can
be given a regional code. If the regional codes differ between the player
and the disc, playback is not possible.
The regional code of the DVD recorder is shown on the type plate at
the back or bottom.
2 channel sound
Some TV programmes transmit an extra audio signal in stereo in
addition to the normal audio signal (2-channel sound). In most cases
this means that an additional language is available. If a TV programme is
available in, say, English and German, German may be available as the
second language.
To record TV programmes in 2-channel sound, you can select the
language you want as the default setting. This setting does not become
active until the sound of a TV programme is transmitted in 2-channel
sound.
When you play back the recording you can play back the sound only in
the language you used for the recording.
Macrovision
Macrovision is a copy-protection technique intended to keep you from
making copies of DVDs with your VCR. It works by continuously
adjusting the video signal level that results in a recording where the
brightness of the picture continuously fluctuates between light and
dark, and the color levels fluctuate between oversaturated and washed
out. Macrovision "encoded" DVDs contain a bit of data that tells the
DVD player to activate its internal macrovision circuitry in order to
prevent copying.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control codes
A Mark ........................................ 146
Action ........................................... 116
Admiral .... 093, 134, 209, 262, 306,
332
Aiko .. 013, 246, 248, 250, 255, 266
Akai .. 002, 113, 114, 140, 216, 246,
248, 250, 255, 266, 285, 292,
305, 324, 332
Akura ......... 217, 222, 246, 250, 266
Alba . 201, 217, 219, 232, 246, 249,
250, 266, 272, 281
Amstrad ... 201, 228, 232, 234, 246,
250, 261, 266, 280, 332
Amtron ........................................... 28
Anam ............................................. 115
Anam National .......... 003, 028, 118
Anglo ............................................. 246
Anitech ..... 201, 246, 250, 256, 332
Ansonic .... 246, 247, 250, 257, 272,
275, 283
Colortyme 004, 006, 114, 130, 134,
Fidelity ........................................... 250
Finlandia ............................... 216, 279
Finlux 208, 209, 211, 212, 250, 254,
255, 256, 257, 258, 262, 279,
283
258, 259, 262, 267, 269,
286, 297, 299, 307, 327,
141, 144, 151
Condor .... 231, 246, 250, 257, 272,
283, 332
Contec ..... 201, 246, 249, 260, 330,
332
Contec Cony ...................... 115, 116
Contec/Cony .... 009, 010, 011, 028
Continental Edison ............ 319, 343
Cosmel ................................. 246, 332
Craig . 028, 115, 116, 128, 137, 141
Crosley ..... 134, 209, 256, 272, 306
Crown ...... 028, 037, 137, 146, 201,
231, 246, 250, 256, 266,
333, 334, 336
Hornyphone ................................ 250
Hoshai ........................................... 266
Huanyu .......................................... 233
Hyper ................. 246, 266, 272, 332
Firstline .... 201, 219, 224, 225, 246,
250, 255, 257, 272, 276,
277, 283
Fisher 033, 044, 096, 129, 140, 149,
211, 216, 231, 249, 253, 255,
260, 306
Formenti ..................... 209, 256, 312
Frontech ............ 222, 246, 272, 332
Fujitsu ................. 032, 255, 257, 266
Funai 028, 032, 115, 116, 136, 222,
224, 262, 276, 330, 332
ICE ............ 222, 232, 246, 250, 266
Imperial ..... 231, 250, 256, 272, 338
Infinity .................................. 006, 037
Ingersol ......................................... 246
Inno Hit ... 239, 246, 250, 255, 256,
266, 272, 305, 322, 323,
289, 332
332
CS Electronics .................... 266, 272
CTC ............................................... 272
Curtis .......................... 113, 144, 152
Curtis Mathes .. 001, 004, 006, 012,
058, 091, 111, 114,
Interbuy ............................... 246, 272
Interfunk .. 247, 250, 274, 306, 319,
320
Intervision 222, 250, 257, 266, 272,
282, 288
Irradio ...... 246, 250, 256, 266, 272,
323, 332
ITS ................................ 232, 250, 266
ITT ............................... 262, 279, 285
ITV ........................................ 250, 272
Galaxi ........................ 250, 257, 338
Galaxis ................................. 250, 257
GBC .................... 246, 266, 305, 332
GE .... 001, 003, 004, 006, 034, 049,
097, 111, 113, 115, 118, 122,
123, 124, 130, 131, 141, 142,
143, 146, 153, 157
GEC .. 205, 250, 251, 255, 305, 333
Geloso ...... 201, 246, 266, 272, 332
Genexxa ..................... 217, 250, 266
GoldHand ..................................... 332
Goldline ........................................ 250
GoldStar .. 004, 005, 006, 009, 015,
091, 092, 113, 114, 117,
AOC 004, 005, 006, 007, 113, 120,
131, 146, 154
120, 131, 134, 141,
146, 147
Arc en Ciel ................................... 319
Aristona ............................... 247, 250
ASA ... 209, 211, 254, 258, 279, 306
Asberg .................................. 250, 256
Astra .............................................. 332
Atlantic ................................ 250, 312
Atori .............................................. 246
Audiosonic ................. 250, 266, 332
AudioTon ..................................... 332
Audiovox ........... 028, 116, 154, 157
Ausind ........................................... 256
Autovox ...................... 209, 256, 272
Awa ...................................... 305, 332
Daewoo . 004, 005, 006, 013, 014,
069, 091, 113, 118, 120,
131, 144, 146, 147, 152,
154, 155, 157, 201, 233,
246, 250, 266, 332, 337
JBL ....................................... 006, 037
JC Penney 001, 004, 005, 006, 008,
034, 044, 049, 058, 091,
Dainichi ................................ 217, 266
Dansai .................................. 248, 250
Daytron ... 004, 006, 091, 128, 131,
146, 152, 154, 201, 246
Decca 220, 250, 255, 305, 309, 339
Denon ........................................... 158
Desmet ......................................... 250
Diamond ....................................... 332
Dimensia .............................. 001, 111
Dixi .............................. 201, 246, 250
Dual ............................. 250, 288, 332
Dumont ... 004, 082, 208, 209, 211,
254, 257, 306
092, 097, 111, 113, 120,
122, 124, 141, 142, 146,
120, 121, 131, 146, 147,
148, 223, 246, 250, 272,
282, 295, 297, 307, 323,
148, 149
Jensen .......................... 004, 006, 114
JVC ... 009, 010, 011, 034, 036, 038,
039, 040, 085, 086, 110, 132,
139, 141, 142, 207, 213, 232,
249, 263, 266, 290, 296, 344
332
Goodmans 219, 232, 233, 246, 248,
249, 250, 255, 262, 285,
Baird ................. 255, 263, 298, 305
Bang & Olufsen ........................... 209
Barco ............................................. 310
Baur .. 202, 237, 240, 242, 250, 264
Beko ............................ 231, 250, 338
Bell & Howell ..................... 134, 262
Beon .............................................. 250
Blaupunkt 214, 215, 221, 240, 242,
264, 303, 316, 324
BPL ................................................. 250
Brandt .................................. 226, 278
Brionvega .. 209, 250, 303, 306, 312
Broksonic ................... 113, 115, 134
Bruns .................................... 209, 306
BSR .............................. 224, 276, 330
BTC ...................................... 217, 266
Bush . 201, 217, 219, 224, 229, 232,
233, 246, 249, 250, 266, 276,
332
Gorenje ........................................ 231
GPM ............................. 217, 266, 332
Gradiente .......... 006, 114, 139, 140
Granada ... 006, 071, 146, 216, 227,
247, 249, 250, 253, 255,
Kaisui201, 217, 246, 250, 266, 332
Kapsch .................................. 211, 312
Karcher ....................... 250, 257, 332
Kathrein ........................................ 243
Kawasho .. 002, 004, 006, 120, 140,
145
Kendo 219, 250, 257, 272, 283, 332
Kennedy ........................................ 312
Kenwood . 004, 006, 015, 113, 114,
120, 130, 151
Kloss Novabeam028, 041, 042, 118
Kneissel ....................... 250, 275, 283
Kolster .......................................... 250
Konka ............................................ 266
Korting .......................................... 209
Kosmos ......................................... 250
KTV . 028, 091, 094, 115, 116, 120,
131, 146
Dynatron ...................................... 250
Elbe . 250, 266, 275, 283, 312, 322
Elcit ....................................... 257, 272
Electroband ....................................... 2
Electrohome .... 003, 004, 006, 015,
113, 114, 131, 146
Elin .... 211, 246, 250, 258, 312, 332
Elite .............................. 217, 250, 266
Elman ............................................. 257
Elta ............................... 201, 246, 332
Emerson .. 004, 006, 009, 016, 017,
018, 019, 020, 021, 022,
256, 268, 278, 320
Grandin ................................ 301, 337
Grundig .... 135, 142, 146, 208, 214,
215, 240, 242, 250, 254,
256, 264, 266, 301, 311,
313, 316, 320, 324, 325,
330, 335, 343
Hallmark .................. 004, 006, 113
Hanseatic . 243, 246, 250, 275, 276,
288, 313
Hantarex..................... 246, 250, 332
Harman Kardon .......................... 113
Harwood ............................. 246, 250
HCM . 201, 234, 246, 250, 266, 332
Hinari 201, 217, 219, 246, 249, 250,
262, 266, 281, 309, 332, 333,
334, 339
281, 288
023, 024, 025, 026, 027,
028, 029, 030, 031, 032,
068, 091, 094, 095, 100,
110, 112, 113, 114, 115,
116, 128, 131, 136, 137,
141, 146, 151, 157, 209,
250, 254, 261, 262, 272,
Carrefour.......................... 249, 254
Cascade ...................... 201, 246, 250
Cathay ........................................... 250
CCE ............................................... 134
Celebrity ............................................ 2
Centurion ..................................... 250
Century ...................... 209, 272, 306
CGE .................... 256, 272, 332, 338
Cimline ............... 201, 219, 246, 266
Citizen ...... 004, 006, 008, 013, 028,
058, 091
Lenco .................................. 211, 246
Lenoir ................................... 246, 332
LG ....................... 246, 250, 272, 282
Liesenkotter ................................ 250
Lloyds ................................... 151, 246
Loewe ................ 037, 209, 250, 275
Loewe Opta ................................. 306
Logik .............................................. 339
Luma ................... 246, 250, 283, 312
Lumatron ...................................... 250
Luxman ................................ 004, 006
Luxor 285, 287, 298, 306, 307, 320,
323
306
Hisawa ........................................... 266
Hitachi ...... 004, 006, 009, 010, 011,
035, 036, 071, 072, 073,
Envision .............. 004, 006, 114, 120
Erres ............................ 203, 247, 250
Europhon .................... 250, 257, 272
Expert ........................................... 312
074, 075, 076, 077, 078,
079, 080, 081, 095, 101,
109, 112, 126, 127, 131,
142, 146, 154, 158, 205,
206, 212, 218, 235, 244,
249, 250, 251, 252, 255,
Classic .................................. 113, 140
Clatronic . 231, 246, 250, 256, 257,
266, 272
Fenner ................................ 246, 332
Ferguson .. 213, 226, 263, 278, 291,
303, 341
90
Download from Www.Somanuals.com. All Manuals Search And Download.
LXI ... 001, 006, 033, 037, 043, 044,
097, 111, 113, 134, 148
Orbit ............................................. 250
Orion 025, 100, 219, 224, 225, 229,
246, 250, 257, 261, 276, 277,
281, 300, 309, 313, 317, 326,
330, 339
Osaki 217, 222, 234, 250, 255, 266,
330
Oso ....................................... 217, 266
Osume ............... 249, 255, 260, 266
Otto Versand .. 202, 214, 219, 237,
240, 242, 243, 249,
RadioShack ................................... 250
Radiotone ................... 246, 250, 289
RCA . 001, 003, 004, 005, 006, 007,
015, 052, 053, 054, 055, 056,
095, 097, 098, 099, 102, 111,
112, 115, 118, 119, 122, 123,
124, 130, 131, 141, 143, 146,
153
Realistic ......................................... 111
Recor ............................................. 250
Revox ............................................ 250
Rex ...................... 222, 272, 283, 312
RFT .............................. 209, 255, 275
Roadstar .. 201, 217, 222, 246, 266,
332
145, 146, 202, 237, 249, 257,
296, 304, 309, 339, 342
Soundesign 004, 006, 008, 028, 032,
113, 115, 131, 137
M Electronic . 201, 211, 212, 233,
236, 246, 250, 258,
Star Lite ............................... 246, 250
Starlite .................................. 028, 332
Stern .............................................. 312
Sunkai219, 224, 225, 229, 266, 276,
277, 281, 330
Sunstar ................................. 246, 250
SuperTech .................. 246, 250, 332
Supra .................................... 246, 332
Susumu ................................. 217, 278
Sylvania ..... 004, 006, 008, 015, 037,
040, 041, 042, 045, 046,
272, 279, 283, 285,
287
Magnadyne 209, 257, 272, 306, 332
Magnafon ............................. 256, 257
Magnasonic 113, 114, 136, 154, 262
Magnavox 004, 006, 008, 015, 037,
041, 042, 045, 046, 070,
250, 264, 268, 272,
276, 302, 303, 313,
113, 114, 120, 128, 131,
133, 134, 136, 137, 142,
324, 330, 332
144, 262
Marantz .... 004, 006, 035, 037, 114,
120, 130, 131, 134, 148,
Palladium 231, 250, 272, 283, 338
Panasonic . 003, 034, 037, 090, 106,
116, 118, 122, 124, 125,
Robotron ...................................... 306
Runco .............................................. 82
088, 113, 114, 120, 128,
131, 134, 136, 137, 144,
243, 250
154
Matsui201, 204, 216, 219, 224, 228,
229, 232, 246, 248, 249, 250,
253, 255, 261, 264, 276, 278,
280, 281, 289, 309, 332, 339,
344
Medion .......................................... 250
Megatron .................... 006, 035, 071
Memorex .. 006, 113, 148, 201, 246
Metz . 209, 230, 240, 264, 270, 274,
306, 308, 311, 313, 324, 325
MGA 004, 005, 006, 015, 047, 114,
266
Minerva .... 208, 240, 242, 254, 256,
264, 311, 324, 325
Minoka ................................. 234, 250
Mission .......................................... 304
Mitsubishi 004, 005, 006, 015, 047,
113, 114, 120, 131, 146,
135, 142, 143, 154, 156,
221, 230, 245, 250, 265,
268, 273, 293, 313, 315,
Saba 209, 226, 278, 291, 303, 306,
310, 319
Saisho201, 219, 222, 228, 246, 261,
266, 280, 309, 339
Salora .......................... 298, 306, 307
Sambers ............. 239, 256, 257, 322
Sampo ...... 004, 006, 091, 092, 118,
120, 131
Samsung ... 004, 005, 006, 009, 012,
015, 057, 058, 059, 091,
Symphonic ......... 023, 028, 116, 136
Tandberg .......................... 283, 330
Tandy 093, 134, 217, 255, 266, 272
Tashiko .............. 205, 249, 251, 333
Tatung ...... 003, 118, 220, 250, 255,
305, 309, 339
Teac ............................................... 250
Tec ............. 246, 272, 278, 284, 332
Technics ... 034, 135, 142, 143, 221,
245
320, 331
Panavision ............................ 250, 283
Pathe Cinema ..................... 275, 338
Pathe Marconi ............................. 319
Perdio ................................... 250, 255
Philco 003, 004, 005, 006, 008, 009,
015, 037, 041, 042, 046, 071,
113, 114, 120, 128, 131, 134,
136, 137, 144, 154, 158, 209,
250, 256, 262, 272, 306, 338
Philips000, 003, 004, 006, 008, 009,
015, 037, 041, 042, 048, 049,
050, 121, 134, 203, 205, 209,
233, 242, 243, 247, 250, 251,
301, 306, 312, 320
092, 103, 113, 120, 131,
134, 141, 146, 151, 159,
201, 222, 223, 231, 239,
243, 246, 250, 255, 262,
Techwood 004, 006, 034, 114, 134
Teknika .... 004, 005, 006, 008, 009,
010, 011, 013, 028, 032,
305, 322, 323, 332, 338
045, 058, 090, 091, 115,
116, 120, 130, 131, 137,
Sansui ................................... 100, 250
Sanyo 004, 033, 047, 060, 089, 096,
129, 149, 211, 216, 227, 246,
249, 253, 255, 260, 275, 298,
305, 306, 309, 332
SBR ..................... 203, 205, 247, 250
Schneider . 217, 232, 247, 250, 266,
272, 288, 332
Scott 004, 006, 009, 016, 025, 028,
032, 115, 116, 131, 136, 146
Sears 001, 004, 006, 010, 011, 015,
032, 033, 039, 040, 043, 044,
061, 071, 096, 097, 111, 113,
115, 129, 134, 146, 149
SEG ............ 222, 246, 249, 250, 272
SEI ..... 202, 209, 224, 250, 257, 276
SEI-Sinudyne ....................... 306, 330
Seleco ................. 283, 303, 312, 319
Sentra ................. 204, 246, 248, 266
Sharp 004, 006, 009, 017, 020, 051,
062, 063, 064, 067, 091, 093,
127, 144, 146, 151, 210, 249,
260, 262, 276, 302, 321, 328,
329, 340
Shorai ................. 224, 262, 276, 330
Siarem 209, 250, 257, 260, 264, 306
Siemens .... 214, 215, 240, 242, 311,
313, 324, 325
Sierra .................................... 247, 250
Signature 2000 ............................ 129
Singer ........ 209, 257, 272, 306, 332
Sinudyne .. 202, 209, 219, 250, 257,
261, 266, 276, 306, 330
Solavox ................................ 255, 307
Sonitron ........................................ 216
Sonoko ...... 201, 246, 250, 266, 332
Sonolor ......................................... 216
Sontec ......................... 250, 276, 338
Sony . 002, 104, 107, 108, 138, 140,
146, 154
Teleavia ......................................... 319
Telecaption .................................... 65
Telecor ................................ 250, 266
Telefunken 151, 226, 250, 278, 284,
291, 303, 319
Telegazi ................................ 250, 266
Telemeister .................................. 250
Telesonic ...................................... 250
Telestar ......................................... 250
Teletech ............. 201, 246, 250, 272
Teleton ................................ 249, 274
Tensai211, 217, 224, 246, 250, 258,
266, 272, 276, 282, 332
Texet .................................... 217, 246
Thomson . 250, 278, 284, 291, 303,
310, 319, 341
Thorn204, 211, 213, 237, 240, 241,
250, 263, 278, 298, 303, 305,
313, 324
150, 209, 228, 240, 249,
250, 280, 306, 309, 324,
Phoenix ....................... 209, 250, 255
Phonola .... 203, 209, 247, 250, 306,
320
Pioneer..... 004, 006, 095, 109, 112,
118, 119, 130, 131, 250
332
Mivar ......... 223, 239, 256, 275, 322
Motorola ............................. 003, 093
MTC 004, 005, 006, 058, 113, 120,
134, 141, 154
Multitech . 028, 201, 246, 250, 257,
266, 272, 332
Portland ... 004, 006, 013, 091, 113,
120, 131, 146, 147, 152
Prandoni-Prince ................. 256, 272
Price Club ...................................... 58
Prima ........................... 147, 246, 332
Prinz .............................................. 255
Prism ............................................... 34
Profex .......................... 201, 246, 332
Profi-Tronic ........................ 250, 257
Proline225, 247, 250, 255, 277, 291
Proscan ....................... 001, 097, 111
Protech ................................ 201, 222
Proton ...... 004, 006, 009, 113, 114,
127, 131, 137, 146, 148
Murphy ................................. 211, 255
NAD .................. 006, 043, 044, 109
National ........................................ 265
NEC . 003, 004, 005, 006, 114, 120,
130, 131, 151, 249, 309, 332
Neckermann .... 209, 214, 237, 242,
243, 250, 272, 283,
306, 313, 338
NEI ................................................. 250
Nesco ................................... 262, 272
Neufunk ............................... 246, 250
Nikkai204, 217, 222, 246, 248, 249,
250, 255, 266, 307
Nikko .......................... 006, 013, 154
NOBLEX ...................................... 332
Nokia 236, 279, 285, 287, 292, 294,
295
Toshiba .... 033, 043, 044, 058, 061,
065, 066, 087, 088, 129,
Provision ....................................... 250
Pye ............................... 203, 247, 250
141, 148, 149, 150, 204,
208, 238, 241, 248, 249,
254, 257, 271, 314, 318
Quasar ... 003, 034, 118, 124, 125,
128, 135, 142, 143
Quelle ...... 202, 208, 211, 237, 240,
242, 249, 250, 254, 258,
260, 264, 272, 306, 309,
322, 324, 330, 332
Totevision ...................................... 91
Towada ......................................... 257
Tristar ........................................... 266
Triumph ............. 250, 261, 271, 279
Nordmende ..... 264, 303, 310, 319,
341
Novatronic .......................... 250, 258
Uher .................. 250, 256, 306, 312
Ultra .............................................. 154
Ultravox ............ 250, 257, 272, 306
Uniden .......................................... 138
Universal ......................................... 49
Universum 211, 212, 222, 231, 240,
249, 250, 254, 256, 258,
RadioShack .. 111, 115, 116, 118,
134, 146
Radio Shack/Realistic 001, 004, 006,
009, 028, 033,
051, 091, 092
Radiola ............... 203, 247, 250, 320
Radiomarelli ............... 209, 250, 272
Oceanic ............................. 276, 298
Okano ......................... 250, 255, 338
Onwa .......................... 028, 115, 266
Optimus ........................................ 109
Optonica ............................. 051, 093
260, 261, 264, 272, 276,
91
Download from Www.Somanuals.com. All Manuals Search And Download.
279, 283, 285, 287, 292,
309, 313, 324, 330, 332
Univox .......................................... 250
Vortec ........................................... 250
Voxson ............... 209, 250, 256, 306
148, 262
Watson .............. 250, 266, 288, 289
Watt Radio .................................. 257
Wega ........................... 209, 249, 250
Weltblick ...................................... 250
White Westinghouse113, 120, 144,
146, 147, 154,
Yamaha . 004, 005, 006, 015, 120,
137, 151, 154
Yoko .......... 222, 246, 250, 266, 332
Yorx ..................................... 266, 332
Waltham.................................... 250
Wards ...... 001, 004, 005, 006, 015,
016, 023, 032, 037, 041,
Vestel .......................................... 250
Video Concepts .......................... 115
VideoSystem ................................ 250
Vidikron ........................................ 134
Vision ............................................ 250
Zenith ..... 004, 082, 083, 084, 105,
042, 045, 049, 051, 111,
113, 120, 122, 123, 131,
134, 136, 137, 141, 144,
117, 138, 154
157, 250
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Storage media
AudioFormat
Compressed digital
Dolby Digital (AC3)
DVD/CD playback
Hard Disc recording:
80 Gb HDD
Playback Recording
5.1- 2-channel
channel* 16-bit, 48
kHz
• Fast Forward/Backward )
• Step Forward/Backward
• Slow
TV systems
Playback:
Recording:
• Direct Title/Track access
• Next/Previous Title/Track/Chapter
• Repeat (Chapter/Title/All) or (Track/All)
• A-B Repeat
• Shuffle
• Intro Scan
• Time Search
• Zoom (1.33x, 2x, 4x) with picture enhancement
• Auto Resume (20 discs)
PAL/NTSC
PAL/NTSC
PAL/SECAM
DTS, MPEG2
5.1-
-
channel*
Internal tuner:
MPEG1, MP3
PCM
2- channel
2-channel
16/20/24 bit
48/96 kHz
-
-
Optical disc
Playback Recording
DVD+RW
DVD+R
DVD-R/-RW, video mode
DVD-Video
Video CD, Super VCD
Audio CD
•
•
•
•
•
•
•
•
•
•
-
-
-
-
-
-
*6.1-channel compatible
AudioPerformance
MP3 CD playback
• Time display (Track)
DA Converter:
AD Converter:
DVD
24 bit
16 bit
• MP3 text (ID3 tags) display
• Album and track selection
• Repeat (disc/album/ track)
• Variable Bit Rate of 32-256 kbit/s
• 32, 44.1, 48 kHz sampling rates
• ISO9660 file system
fs 96kHz 4Hz-44kHz
fs 48kHz 4Hz-22kHz
fs 44.1kHz 4Hz-20kHz
fs 44.1kHz 4Hz-20kHz
105 dB
90 dB
105 dB
90 dB
MP3 CD
CD-R/RW
Video CD
Audio CD
Signal/Noise (1kHz):
Dynamic range (1kHz):
Crosstalk (1kHz):
Distortion/Noise (1kHz):
VideoFormat
Digital compression
DVD, SVCD: MPEG2
VCD: MPEG1
• Single session
• Nested directories supported to 8 levels
• Up to 32 album numbers
• Up to 999 tracks
Record modes
Front Connections
Max HDD recording time: 120h
Max DVD recording time: 8h
i.LINK DV in:
S-video in:
IEEE 1394 4-pin
Hosiden 4-pin
Cinch (yellow)
Cinch (white/red)
Power Supply
Power supply: 200-240 V, 50 Hz
Power consumption Operation 38 W
Low-power standby 8 W
Bit rate
Mode Rec.time Resolutio- Video
Video in:
Audio Left/Right in:
Audio
(Mbit/s) (kbit/s)
n
M1
M2
M2x
M3
M4
M6
M8
60'
D1
D1
D1
1/2 D1
1/2 D1
1/2 D1
SIF
9.72M
5.07M
4.06M
3.38M
2.54M
1.70M
1.27M
384k
256k
256k
256k
256k
256k
192k
Rear Connections
SCART1:
SCART2:
Cabinet
120'
150'
180'
240'
360'
480'
CVBS, S-video, RGB out
CVBS, S-video, RGB in
decoder
Cinch (yellow)
Cinch (white/red)
Hosiden 4-pin
Dimensions (W x H x D): 435 x 76 x 335 mm
Net Weight: 4.0kg
Remote Control
Video out:
Audio L/R out (2x):
S-video out:
• Multi brand remote control
Package Contents
• DVD Video Recorder/Harddisc
• Remote Control + batteries
• User Manual
• AC power cable
• Coax RF antenna cable
Digital audio out:
RF antenna in:
RF TV out:
Mains:
Component video out:
Coaxial, Optical
Resolution H x V
(pixels)
Full D1 (DVD-Video)
Half D1
SIF (VCD)
TV Standard
50Hz
Coaxial 75 ohms (F type)
Coaxial 75 ohms (F type)
Standard (IEC type)
Cinch (green/blue/red)
720 x 576
360 x 576
352 x 288
NTSC
PAL/
SECAM
50Hz
625
•
•
•
• SCART cable fully connected
• IR-extender cable (G-LINK transmitter)
Timer Recording
Number of events:
Record control:
Autom. Sat. Recording:
Timer programming:
12; 1 month; daily/weekly
VPS, PDC
On SCART 2
Scan frequency
Number of lines
Playback
Recording
Internal tuner
60Hz
525
Philips Consumer Electronics
•
•
-
Data subject to change without notice
Manual, ShowView
Electronic Program Guide
Timer programming: GUIDE Plus+/ShowView/Manual
Number of events: 12; 1 month; daily/weekly
VideoPerformance
DA Converter:
AD Converter:
Signal handling:
10 bit
9 bit
Components
1 Vpp into 75 ohm
Y: 1 Vpp into 75 ohm
C: 0.286 1Vpp into 75 ohm
General Functionality
Automatic Screen Saver
Backup presets & timer:
Backup clock & calendar:
Auto clock set (SMART
CLOCK):
1 year
5 hours
PDC, Teletext (Time/Date)
Video (CVBS) out:
S-video (Y/C) out:
Audio recording level:
TV-related functions:
Automatic
16:9 (pin8), Follow TV,
Direct Record
Component video out
(YPBPR):
Y: 1 Vpp into 75 ohm
PB: 0.7 Vpp into 75 ohm
PR: 0.7 Vpp into 75 ohm
Download from Www.Somanuals.com. All Manuals Search And Download.
PHILIPS NORGE AS
Sandstuveien 70,
PO Box 1, Manglerud
N-0612 Oslo
PHILIPS
PHILIPS PORTUGUESA, S.A.
Consumer Information Centre
Rua Dr. António Loureiro Borge, nr. 5
Arquiparque, Miraflores
Philips Austria GmbH
Triesterstrasse 64
1101 Wien
NORWAY
AUSTRIA
P-2795 L-A-VEHLA
Phone: 2274 8250
Tel: 0810 00 12 03
PORTUGAL
Phone: 2 1416 3033
OY PHILIPS AB
Sinikalliontie 3,
02630 Espo
PHILIPS INFO CENTER
Alexanderstrasse 1
20099 Hamburg
PHILIPS CE, The Philips Centre,
420 - 430 London Road,
Croydon, Surrey
Helsinki
GERMANY
CR9 3QR
FINLAND
puh. (09) 6158 0250
Tel: 0180-535 6767
UNITED KINGDOM
Phone: 0870-900-9070
PHILIPS KUNDTJÄNST
Kollbygatan 7,
SERVICE CONSOMMATEURS PHILIPS
BP 0101
PHILIPS KUNDECENTER
Frederikskaj 6,
Akalla,
16485 Stockholm
SWEDEN
75622 Paris Cédex 13
FRANCE
Phone: 0825-889 789
DK-1780 København V
DENMARK
Tlf: 808 82814
Phone: 08-5985 2250
PHILIPS POLSKA
AL. Jerozolimskie 195B
02-222 Warszawa
POLSKA
PHILIPS ELECTRONICS IRELAND LIMITED
Consumer Information Centre
Newstead, Clonskeagh
PHILIPS REPRESENTATION OFFICE
Ul. Usacheva 35a
119048 MOSCOW
DUBLIN 14
RUSSIA
Tel.: (022)-571-0-571
Phone: 01-7640292
Phone: 095-937 9300
PHILIPS SERVICE
V Mezihori 2
180 00 Prage
CZECH REPUBLIC
Phone: (02)-3309 9240
PHILIPS CONSUMER ELETRONICS
Servizio Consumatori
Via Casati 26
20052 Monza - Milano
ITALY
PHILIPS INFO CENTER
Fegistrasse 5
8957 Spreitenbach
SUISSE
Tel.: 0844-800 544
Phone: 199 11 88 99
PHILIPS Iberia, S.A.
C/Martinez Villergas, 49
28027 MADRID
PHILIPS MÁRKASZERVIZ
Kinizsi U 30-36
Budapest 1119
PHILIPS CUSTOMER CARE CENTER
Twee Stationsstraat 80/
80 Rue des Deux Gares
SPAIN
Phone: 902-113 384
HUNGARY
Phone: (01)-382 1700
1070 BRUSSEL/BRUXELLES
BELGIUM (for BENELUX)
Tel: 070-222 303
ΦΙΛΙΠΣ ΕΛΛAΣ AΕΒΕ
PHILIPS CONSUMENTENLIJN
25ΗΣ MAΡΤΙΟΥ 15
177 78 ΤAΥΡΟΣ
AΘΗΝA
t.a.v. betreffende afdeling
Postbus 102 5600 AC Eindhoven
NETHERLANDS
Τηλ. 0 0800 3122 1280
Phone: 0900-8406
HDRW 720/00 02
Download from Www.Somanuals.com. All Manuals Search And Download.
|