Philips Computer Hardware ADM0101 User Manual

Eng  
Philips  
Communication,  
Security & Imaging  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY PRECAUTIONS  
SECURITE  
CAUTION: TO REDUCE THE RISK OF  
ELECTRICAL SHOCK, DO NOT OPEN  
COVERS. NO USER SERVICEABLE PARTS  
INSIDE. REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
DANGER : POUR ÉVITER TOUT RISQUE  
D’ÉLECTROCUTION, VEUILLEZ NE PAS  
OUVRIR LE BOÎTIER. IL N’Y A PAS DE  
PIÈCES REMPLAÇABLES PAR L’UTILISATEUR  
À L’INTÉRIEUR DU BOÎTIER. POUR TOUTE  
MAINTENANCE, VEUILLEZ VOUS ADRESSER  
À UN TECHNICIEN SPÉCIALISÉ.  
The lightning flash with an arrowhead symbol within  
an equilateral triangle is intended to alert the user to the  
presence of uninsulated “dangerous voltage” within the  
product’s enclosure that may be of sufficient magnitude  
to constitute a risk of electric shock to persons.  
L’éclair fléché dans un triangle équilatéral avertit  
l’utilisateur de la présence d’une “tension dangereuse” non  
isolée à l’intérieur de l’appareil et d’une valeur suffisante  
pour présenter un risque d’électrocution aux personnes.  
The exclamation point within an equilateral triangle is  
intended to alert the user to presence of important  
operating and maintenance (servicing) instructions in  
the literature accompanying the appliance.  
Le point d’exclamation contenu dans un triangle  
équilatéral avertit l’utilisateur de la présence de  
consignes d’utilisation et de maintenance importantes  
dans la documentation qui accompagne l’appareil.  
WARNING  
TO PREVENT FIRE OR SHOCK HAZARD, DO  
NOT EXPOSE UNITS NOT SPECIFICALLY  
DESIGNED FOR OUTDOOR USE TO RAIN OR  
MOISTURE.  
ATTENTION  
POUR ÉVITER TOUT RISQUE  
D’ÉLECTROCUTION OU D’INCENDIE,  
VEUILLEZ NE PAS EXPOSER À LA PLUIE OU  
À L’HUMIDITÉ UN APPAREIL NON CONÇU  
POUR UNE UTILISATION EXTÉRIEURE.  
Attention: Installation should be performed by  
qualified service personnel only in accordance with the  
National Electrical Code or applicable local codes.  
Attention. L’installation ne doit être effectuée que par  
un personnel technique qualifié conformément à la  
réglementation du Code Électrique National ou à la  
réglementation locale pertinente.  
Power Disconnect. Units with or without ON-OFF  
switches have power supplied to the unit whenever the  
power cord is inserted into the power source; however,  
the unit is operational only when the ON-OFF switch  
is in the ON position. The power cord is the main  
power disconnect for all units.  
Disjonction de l’alimentation. Les appareils avec ou sans  
commutateurs ON-OFF sont alimentés à chaque fois  
que le cordon d’alimentation est branché à la source  
d’alimentation; toutefois, les appareils disposant de  
commutateurs ON-OFF ne fonctionnent que lorsque le  
commutateur ON-OFF est dans la position ON. Le  
cordon d’alimentation constitue le moyen de disjonction  
de l’alimentation principale de tous les appareils.  
WARNING: Electrostatic-  
sensitive device. Use proper  
CMOS/MOSFET handling  
precautions to avoid  
CAUTION: Lithium Battery  
Danger of explosion if battery is  
incorrectly replaced. Replace only with  
the same or equivalent type  
recommended by the manufacturer.  
Dispose of used batteries according to  
the battery manufacturer’s instructions  
electrostatic discharge.  
A
T
T
E
N
T
I
O
N
NOTE: Grounded wrist straps  
must be worn and proper ESD  
safety precautions observed  
O
B
S
E
R
V
E
P
R
E
C
A
U
T
I
O
N
S
O
R
H
A
N
D
L
I
N
G
E
L
E
C
T
R
O
S
T
A
T
I
C
S
E
N
S
I
T
I
V
E
D
E
V
I
C
E
S
when handling the electrostatic-  
sensitive printed circuit boards.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SICHERHEITSHINWEISE  
SEGURIDAD  
VORSICHT  
ELEKTRISCHE SPANNUNG.  
NICHT ÖFFNEN!  
PRECAUCIÓN  
RIESGO DE DESCARGA ELÉCTRICA  
¡NOABRIR!  
PRECAUCIÓN: PARA REDUCIR EL RIESGO  
DE DESCARGA ELÉCTRICA, NO ABRA LAS  
TAPAS. EN EL INTERIOR NO HAY NINGÚN  
COMPONENTE REPARABLE POR EL USUARIO.  
LAS REPARACIONES DEBE REALIZARLAS  
PERSONAL CUALIFICADO.  
VORSICHT: DAS GEHÄUSE ZUR  
VERMEIDUNG VON ELEKTRISCHEN  
SCHLÄGEN NICHT ÖFFNEN. DAS GERÄT  
ENTHÄLT KEINE VOM BENUTZER ZU  
WARTENDEN TEILE. REPARATUREN NUR  
VON FACHPERSONAL AUSFÜHREN LASSEN.  
Das Blitzsymbol im gleichseitigen Dreieck soll den  
Benutzer auf nicht isolierte “gefährliche Spannung” im  
Produkt hinweisen, die ausreichend stark sein kann,  
um die Gefahr von elektrischen Schlägen für  
Menschen darzustellen.  
El símbolo de flecha en forma de rayo situado dentro  
de un triángulo equilátero pretende alertar al usuario  
de la presencia de “voltaje peligroso” sin aislamiento  
dentro de la caja del producto, el cual podría resultar  
de una magnitud suficiente como para presentar un  
riesgo de descarga eléctrica para las personas.  
Das Ausrufungszeichen im gleichseitigen Dreieck soll  
den Benutzer auf wichtige Bedienungs- und  
Wartungsanweisungen in der Dokumentation  
hinweisen, die dem Gerät beiliegt.  
El punto de exclamación dentro de un triángulo equilátero  
pretende alertar al usuario de la existencia de instrucciones  
de funcionamiento y mantenimiento (reparación) en la  
documentación suministrada con el aparato.  
WARNUNG  
ZUR VERMEIDUNG VON FEUER UND  
ELEKTRISCHEN SCHLÄGEN DAS GERÄT  
NICHT REGEN ODER FEUCHTIGKEIT  
AUSSETZEN.  
AVISO  
PARA IMPEDIR EL RIESGO DE INCENDIO O  
DESCARGA, NO EXPONGA EL APARATO A  
LLUVIA O HUMEDAD  
Achtung: Die Installation darf nur von qualifiziertem  
Wartungspersonal gemäß dem National Electrical  
Code oder den gültigen örtlichen Vorschriften  
durchgeführt werden.  
Atención: La instalación debe realizarla personal  
cualificado en cumplimiento estricto del código  
eléctrico nacional (en el caso de los EE.UU.) o de los  
códigos locales aplicables.  
Abtrennen der Spannungsversorgung: Die  
Para Desconectar la Alimentación: Unidades no  
equipadas con interruptores ON/OFF, son alimentadas  
cuando el cable de alimentación es conectado a la  
corriente eléctrica. Las unidades equipadas con  
interruptores son alimentadas de igual forma, pero  
adicionalmente requieren que el interruptor esté  
posicionado en ON. El cable de alimentación es el  
medio principal de desconexión del equipo.  
Spannungsversorgung zu Geräten mit und ohne  
Ein/Aus-Schalter ist hergestellt, wenn das Netzkabel an  
eine Netzsteckdose angeschlossen ist. Das Gerät ist  
jedoch nur betriebsbereit, wenn der Ein/Aus-Schalter  
eingeschaltet ist. Bei allen Geräten erfolgt das Abtrennen  
der Spannungsversorgung über das Netzkabel.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
VEILIGHEIDSMAATREGELEN  
SICUREZZA  
VOORZICHTIG  
GEVAARVOOR ELEKTRISCHE SCHOK.  
NIET OPENEN!  
ATTENZIONE  
PERICOLO DI SCOSSA ELETTRICA.  
NONAPRIRE.  
VOORZICHTIG: MAAK HET APPARAAT NIET  
OPEN OM DE KANS OP ELEKTRISCHE  
SCHOKKEN TE VERMIJDEN. BEVAT GEEN  
ONDERDELEN DIE DOOR DE GEBRUIKER  
MOETEN WORDEN ONDERHOUDEN. LAAT  
ONDERHOUD EN REPARATIES UITVOEREN  
DOOR BEVOEGDE TECHNICI.  
ATTENZIONE: PER RIDURRE IL PERICOLO DI  
SCOSSA ELETTRICA, NON APRIRE LE  
COPERTURE. L’INTERNO NON CONTIENE  
COMPONENTI CHE L’UTENTE PUÒ  
RIPARARE PERSONALMENTE. RIVOLGERSI AL  
PERSONALE DI ASSISTENZA QUALIFICATO  
PER QUALSIASI INTERVENTO DI  
RIPARAZIONE.  
Het symbool ‘Bliksemflits met pijlkop’ in een  
gelijkzijdige driehoek wijst de gebruiker op de  
aanwezigheid in de kast van het apparaat van niet-  
geïsoleerde spanningen die voldoende sterk zijn om  
het gevaar van elektrische schokken op te leveren.  
Il simbolo triangolare di un fulmine con la punta a  
freccia intende mettere in allerta l’utente riguardo alla  
presenza di tensioni pericolose non isolate all’interno  
del guscio dell’unità, che potrebbero essere di intensità  
sufficiente per costituire pericolo di elettrocuzione.  
Het uitroepteken in een gelijkzijdige driehoek maakt  
de gebruiker attent op de aanwezigheid in de bij het  
apparaat behorende documentatie van belangrijke  
aanwijzingen voor bediening en onderhoud.  
Il punto esclamativo racchiuso in un triangolo equilatero  
intende avvisare l’utente in merito alla presenza di  
importanti istruzioni operative e di manutenzione nella  
documentazione di accompagnamento all’unità.  
WAARSCHUWING  
TER VOORKOMING VAN BRANDGEVAAR  
EN ELEKTRISCHE SCHOKKEN MAG DIT  
ARMATUUR NIET AAN REGEN EN VOCHT  
WORDEN BLOOTGESTELD.  
AVVERTENZA  
PER IMPEDIRE INCENDI O SCOSSA  
ELETTRICA, NON ESPORRE L’UNITÀ ALLA  
PIOGGIA O ALL’UMIDITÀ.  
Let op: Het apparaat mag uitsluitend door bevoegde  
technici geïnstalleerd worden en wel in overeenstemming  
met de National Electrical Code of de daarvoor  
plaatselijk geldende richtlijnen.  
Precauzione: affidare l’installazione al solo personale  
qualificato e nel rispetto del Codice elettrico nazionale  
(USA) o dei codici locali pertinenti.  
Scollegamento dell’alimentazione. Gli apparecchi con o  
senza commutatori ON-OFF ricevono corrente tutte le  
volte che il cavo di alimentazione è inserito nella presa  
di forza; tuttavia, gli apparecchi muniti di commutatore  
ON-OFF funzionano solo se quest’ultimo è in posizione  
ON. Il cavo di alimentazione serve a scollegare dalla  
corrente tutti gli apparecchi.  
Afsluiten voeding. Apparaten met of zonder  
ON-OFF-schakelaar krijgen voeding zodra het  
netsnoer in de wandcontactdoos wordt gestoken; het  
apparaat is echter alleen operationeel als de ON-OFF-  
schakelaar op ON staat. Het netsnoer kan bij alle  
apparaten worden gebruikt om deze uit te schakelen.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
´
MEDIDAS DE SEGURANÇA  
ZASADY BESPIECZENSTAWA  
CUIDADO  
RISCO DE CHOQUE ELÉCTRICO.  
OABRIR!  
UWAGA  
NIEBEZPIECZEŃSTWO PORAŻENIA PRĄDEM  
ELEKTRYCZNYM.NIE OTWIERAĆ!  
CUIDADO: PARA REDUZIR O RISCO DE  
CHOQUE ELÉCTRICO, NÃO ABRA ASTAM-  
PAS. O INTERIOR NÃO CONTÉM PEÇAS QUE  
NECESSITEM DE MANUTENÇÃO.A  
MANUTENÇÃO DEVE SER EFECTUADA POR  
PESSOAL DE ASSISTÊNCIATÉCNICA QUALI-  
FICADO.  
UWAGA: ZEWZGLĘDU NA  
NIEBEZPIECZEŃSTWO PORAŻENIA PRĄDEM  
NIEWOLNO OTWIERAĀ POKRYWY.W  
ŚRODKU NIE MA ŻADNYCH ELEMENTÓW,  
KTÓRE MOGĄ BYĀ NAPRAWIANE PRZEZ  
UŻYTKOWNIKA. NAPRAWĘ NALEŻY  
POWIERZYĀ AUTORYZOWANEMU PUNK-  
TOWI SERWISOWEMU.  
O símbolo do raio com a cabeça de uma seta dentro  
de um triângulo equilátero serve para alertar o utilizar  
para a presença de "corrente eléctrica perigosa" não  
isolada no interior da caixa do produto que pode ser  
suficiente para dar origem a choques eléctricos.  
Błyskawica ze strzałką wewnątrz trójkąta równobocznego  
ma za zadanie zwrócić uwagę użytkownika na obecność  
nieizolowanego "niebezpiecznego napięcia" wewnątrz  
obudowy urządzenia, o wielkości stwarzającej niebez-  
pieczeństwo porażenia prądem.  
O ponto de exclamação dentro de um triângulo equilátero  
serve para alertar o utilizador para a presença de instruções  
de funcionamento e manutenção importantes na docu-  
mentação fornecida com o aparelho.  
Wykrzyknik wewnątrz trójkąta równobocznego ma za  
zadanie zwrócić uwagę użytkownika na ważne czynności,  
związane z obsługą i konserwacją urządzenia, zamieszc-  
zone w Instrukcji obsługi.  
AVISO  
PARA EVITAR INCÊNDIOS OU CHOQUES  
ELÉCTRICOS, NÃO EXPONHA À CHUVA OU  
HUMIDADE UNIDADES NÃO ESPECIFICA-  
MENTE CRIADAS PARA UTILIZAÇÃO NO  
EXTERIOR.  
OSTRZEŻENIE  
ABY UNIKNĄĀ POŻARU LUB PORAŻENIA  
PRĄDEM NIEWOLNOWYSTAWIAĀ NA  
DZIAŁANIE DESZCZU LUBWILGOCI  
URZĄDZEŃ, KTÓRE NIE ZOSTAŁY SPECJALNIE  
ZAPROJEKTOWANE DO UŻYWANIA NA  
OTWARTYM POWIETRZU.  
Atenção: A instalação deve ser efectuada por pessoal de  
assistência técnica qualificado, de acordo com o  
National Electrical Code (Normas de Electricidade  
Nacionais) ou a legislação local aplicável.  
Uwaga: Instalację urządzenia powinien wykonać tylko  
wykwalifikowany personel, zgodnie z przepisami NEC lub  
odpowiednimi przepisami miejscowymi.  
Desconexão da electricidade. Unidades com ou sem  
interruptores ON-OFF são activadas sempre que o  
cabo eléctrico for ligado a uma fonte de alimentação.  
No entanto, a unidade fica operacional apenas quando  
o interruptor ON-OFF se encontrar na posição ON.  
Para desligar a electricidade em qualquer uma das  
unidades deve ser utilizado o cabo eléctrico.  
Odłączanie zasilania. Urządzenia zarówno nie posiada-  
jące, jak i posiadające wyłączniki ON-OFF znajdują się  
pod napięciem, jeżeli tylko przewód zasilający jest  
połączony ze źródłem zasilania. Jednakże urządzenie  
działa tylko wtedy, gdy wyłącznik znajduje się w położeniu  
ON. Przewód zasilający jest głównym odłącznikiem zasila-  
nia dla wszystkich rodzajów urządzeń.  
Precauções a ter durante a substituição da bateria  
Use apenas fontes de alimentação recomendadas. As  
fontes de alimentação devem cumprir os requisitos da  
da versão mais recente de IEC 65/VDE 0860.  
Qualquer substituição pode causar danos na unidade  
ou dar origem a incêndios ou choques eléctricos.  
Wymiana baterii  
Stosuj tylko zalecane baterie. Muszą one spełniać wyma-  
gania najnowszej wersji IEC 65/VDE 0860. Zamienniki  
mogą uszkodzić urządzenie lub spowodować pożar czy  
porażenie prądem.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
1 PRODUCT DESCRIPTION..............................................................................................................................8  
1.1 Models ................................................................................................................................................................8  
1.2 Features................................................................................................................................................................8  
2 UNPACKING......................................................................................................................................................8  
2.1 Package Contents ................................................................................................................................................8  
3 SYSTEM OVERVIEW ........................................................................................................................................8  
4 ADIM CONNECTIONS AND CONFIGURATION........................................................................................10  
4.1 DVR Configuration (See DVR manual)............................................................................................................10  
4.2 IntuiKey Keyboard and Serial Hub Connections ..............................................................................................10  
4.3 ADIM PC is pre-configured as follows ..............................................................................................................10  
4.4 Primary DVR Connections................................................................................................................................10  
4.5 Backup DVR and Review Monitor Connections (Optional) ............................................................................10  
4.6 Network Connections........................................................................................................................................11  
4.7 ADIM PC Connections ....................................................................................................................................11  
4.8 The PC is pre-configured with the following network parameters ....................................................................11  
4.9 Setting up ADIM PC Connections....................................................................................................................11  
4.10 Allegiant Connections ......................................................................................................................................11  
5 ADIM CONFIGURATION ..............................................................................................................................12  
5.1 Logging ON and User Levels ............................................................................................................................12  
6 OPERATION....................................................................................................................................................13  
6.1 DVR Configuration Page ..................................................................................................................................13  
6.2 Other Configuration..........................................................................................................................................14  
6.2.1 Allegiant Status Message Monitors..................................................................................................................................14  
6.2.2 Auto-Login....................................................................................................................................................................14  
6.2.3 Keyboard / Com Port Assignment ..................................................................................................................................14  
6.3 Status and Monitoring Page ..............................................................................................................................15  
6.4 Allegiant Camera Title Transfer Dialog ..............................................................................................................16  
7 ADIM KEYBOARD OPERATION ..................................................................................................................17  
7.1 Product Menu....................................................................................................................................................17  
7.2 Allegiant Main Menu ........................................................................................................................................17  
7.3 ADIM Controls Menu ......................................................................................................................................17  
7.4 Joystick Operation ............................................................................................................................................17  
7.5 Numeric Keypad Buttons ..................................................................................................................................17  
7.6 Softkey Buttons ................................................................................................................................................17  
7.7 Keyboard Error Handling ..................................................................................................................................17  
7.8 Clearing ADIM Alarms ....................................................................................................................................17  
8 TROUBLESHOOTING....................................................................................................................................18  
APPENDIX A – EVENT LOGS ..........................................................................................................................19  
APPENDIX B – TECHNICAL SPECS ................................................................................................................22  
APPENDIX C – RECOMMENDED NETWORK SWITCHES..........................................................................23  
APPENDIX D – LIST OF COMPATIBLE DVRS ..............................................................................................23  
APPENDIX E – PRIMARY, BACK-UP AND REVIEW DVRS ..........................................................................23  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
PRODUCT DESCRIPTION  
ADIMis a powerful security and surveillance solution that  
combines the power and features of the Philips Allegiant matrix  
switcher with the speed and quality of digital video recording.  
This tightly integrated solution uses the IntuiKey keyboard to  
control all cameras, monitors and digital video recorders. With  
the push of a button, the DVR will playback video from the  
current camera and display it on the specified CCTV monitor.  
The joystick can be used to fast forward, fast reverse and  
navigate the menu within the DVR.  
1.1 Models  
ADM0101 (see package contents below)  
1.2 Features  
IntuiKey Keyboard interface for all Camera, Allegiant® and  
DVR functions  
One-button transition from Live to recorded videoon the  
specified analog monitor  
Synchronization of DVR and Allegiant clocks  
Status monitoring and event logging  
Automatic switchover to backup DVRs  
Monitor review; playback all video that was directed to  
specified review monitors  
3
SYSTEM OVERVIEW  
ADIM is an integration solution for the IntuiKey Keyboard,  
Allegiant Matrix Switcher and selected Philips DVRs.  
2
UNPACKING  
Unpack carefully to prevent damage to the equipment.  
Components of an ADIM system:  
2.1 Package Contents  
Allegiant matrix switcher  
Hi-Qs (Revision 1.10 or higher)  
Disk Arrays (optional)  
ADIM PC  
Serial Hub(s)  
Universal IntuiKey Keyboard(s) – (Rev 1.10 or higher)  
Network Switch(es) – (See Appendix C for recommended  
network switches.)  
Item  
Qty  
Part Number  
ADIM PC (keyboard, mouse,  
monitor, power cord,  
Windows NT®, ADIM and  
system software, rack mounting  
hardware)  
1
3033743001  
NOTE: For your convenience, the Hi-Q Management Utility  
and the IntuiKey Keyboard’s Installer program are pre-installed  
on the ADIM PC.  
Software Key  
1
1
1
2
1
1
1
1
3031874021002  
30336800100  
ACCSH01  
Master Control software  
Serial Hub  
Ethernet Cable  
3032779001  
Console Cable, 10-foot  
Null Modem Cable, 15-foot  
Instruction Manual (this manual)  
LTC 8506/00  
ACCNM015  
393589042712*  
393589012413  
Master Control Software for  
Windows Manual  
* Revision of this Instruction Manual will increment as changes are  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Typical System:  
Back-up Recorder  
Allegiant  
Video  
Monitor Outputs  
Disk Array  
Loop-through  
PHILIPS  
ALLEGIANT Video Matrix  
Review Monitor  
Video  
Inputs  
Recorder  
PHILIPS  
PHILIPS  
PHILIPS  
PHILIPS  
Network Switch  
LAN  
Network  
ADIM  
Maximum of  
6 Keyboards  
Serial Hub  
IMPORTANT NOTES:  
Disk Arrays are optional. (See specific DVR for Disk Array  
options.)  
may be a master in a satellite configuration, with DVRs at  
both master and satellite sites.  
Additional Serial Hubs may be used for remote keyboards.  
The ADIM system can handle a maximum of 6 keyboards;  
additional Keyboards may be connected to the Allegiant for  
live monitoring and camera control.  
Ensure the Allegiant has sufficient inputs for all cameras, DVR  
MON A outputs and optional Backup DVR MON A outputs.  
Ensure the Allegiant has sufficient outputs for all Backup  
DVR inputs.  
ADIM can only be used with compatible Philips DVRs.  
(See Appendix D.)  
Only one user at a time can access a particular DVR. To  
avoid situations where high priority cameras are not accessible  
for playback, avoid placing more than one high priority  
camera on each DVR.  
This system is designed to operate on its own closed network.  
The ADIM PC does not take the place of the 8900 Series PC.  
An LTC 8900 Allegiant System will still require its  
LTC 8943/92 PC.  
The DVRs can be configured as Review Monitors, providing  
playback capability only for cameras that were directed to the  
specific monitors.  
The ADIM supports only one Allegiant system. The Allegiant  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.3  
ADIM PC is pre-configured as follows:  
Serial Hub’s  
Physical Port  
4
ADIM CONNECTIONS AND  
CONFIGURATION  
PC COM Port  
NOTE: The installer should be familiar with the Allegiant CCTV  
control system and Windows-based software, and have a general  
knowledge of networking.  
1
2
3
4
5
6
7
8
5
6
4.1 DVR Configuration (See DVR manual)  
Configure each DVR with a unique IP address  
7
8
9
Ensure valid IP addresses are configured  
Set the DVRs recording parameters  
Ensure the Hi-Q’s password is set to 1234 (this is the default  
password)  
10  
11*  
12*  
4.2  
IntuiKey Keyboard and Serial Hub Connections  
Connect each IntuiKey Keyboard to the Allegiant via an  
RS-485 cable (not supplied).  
*Not Used; On the Serial Hub, keyboard cables can be  
connected to Ports 1 through 6, Ports 7 & 8 are not used.  
IMPORTANT: Please make note of your connections (COM port  
configurations in Sections 4.4 & 4.5) for future reference.  
Connect each IntuiKey Keyboard to the Serial Hub via a null  
modem cable (a 15-foot cable is supplied).  
4.4 Primary DVR Connections  
Connect the serial hub to the network via an ethernet cable  
(2 are supplied).  
Connect the camera to the Primary DVR inputs and loop  
video to the Allegiant inputs.  
IMPORTANT:  
Connect the MON A output of the Primary DVRs to  
Allegiant inputs.  
The serial hub must be on the same network segment as the  
ADIM PC.  
Figure 4.1 shows the relationship of the Primary DVR outputs and  
Allegiant inputs to the DVR Configuration page of the ADIM.  
If the distance from your Keyboard to the Serial Hub exceeds  
RS-232 limitations (50 feet), use a modem or additional Serial  
Hub to extend the distance. (See Appendix B for the RS-232  
pin out details.)  
4.5 Backup DVR and Review Monitor Connections  
(Optional)  
Connect the Allegiant Monitor Outputs to the Backup or  
Review DVR video inputs.  
Connect the MON A output of the DVRs to an Allegiant  
input.  
Rear View of the Serial Hub  
101 102 234 536 32  
Loop OutVideo  
Mon A  
2
4
3
1
II
PHILIPS  
PHILIPS  
PHILIPS  
101  
1
32  
102  
234  
536  
2
3
4
Figure 4.1  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
4
3
2
1
ALL
Monitor Outputs  
10  
11 12 13  
Figure 4.2  
4.8 The PC is pre-configured with the following  
network parameters  
Figure 4.2 Shows the relationship of the Backup and Review  
DVRs and Allegiant outputs to the DVR Configuration page of  
the ADIM.  
IP address: 10.10.0.10  
Subnet mask: 255.255.255.0  
4.6 Network Connections  
Interconnect the Serial Hub(s). ADIM PC, DVRs and  
network switches.  
Default Gateway: 10.10.0.1  
Philips recommends that your IT department perform all  
network and set up configuration.  
NOTE: Connect the ADIM PC to the Network using the port  
labeled LAN – Connect to Primary IP address.  
NOTE: The PC is pre-configured to communicate with  
the Serial Hub that is shipped with ADIM. If a different Serial  
Hub is used with the system, the PC must be reconfigured.  
(Refer to the Serial Hub’s instruction manual.)  
Serial Hub  
NOTE: A printer or other device can be connected onto the  
security key, but the key may not function properly unless the  
device is turned on.  
4.9 Setting up ADIM PC Connections  
1. Connect the keyboard and mouse “Y” adapter to the  
mouse/keyboard port on back of PC. Connect the mouse  
and the keyboard to the “Y” adapter.  
2. Connect the PC monitor to the port labeled  
“PC Monitor Connector”. Plug the PC and Monitor power  
cords into the appropriate power sources, but do not turn on  
the power switches yet.  
3. Connect the ADIM PC to Allegiant Console Port.  
• Use the console cable to connect PC COM port number 1  
to the Allegiant Console port.  
• Make sure that the ADIM PC is configured for the same  
network segment as the Hi-Q Recorders  
[10.10.0.0/255.255. 255.0/10.10.0.1 (defaults)].  
4. Connect the ADIM PC to the Network Switch.  
5. Turn on the power switches to the PC and the  
monitor.  
4.7 ADIM PC Connections  
4.10 Allegiant Connections  
Connect the Allegiant to a PC COM Port 1 (recommended)  
using the supplied Console cable.  
Connect the Software Key to the parallel port of the PC.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Select or create an Allegiant Server document.  
5
ADIM CONFIGURATION  
The ADIM software is pre-loaded. No software installation is  
required.  
Open the ADIM Application by double clicking the  
ADIM icon on your desktop.  
5.1 Logging ON and User Levels  
Log in with a user name and password.  
NOTE: ADIM will automatically open the last Allegiant  
document, therefore this screen may not be seen.  
2. If creating a new Allegiant document, select the type of  
Allegiant:  
If configuring the system, logon as a user with Installer or  
Administrator privileges. This grants access to all areas.  
NOTE: The ADIM’s user name and password are the same as  
the Master Control Software for Windows.  
User levels for ADIM and Master Control Software for  
Windows:  
Default User  
Names  
Default  
Passwords  
User Level  
Areas of Access  
Status, Monitoring  
& Configuration  
Installer  
Installer  
1
Status, Monitoring  
& Configuration  
Administrator Administrator  
Operator Operator  
2
3
3. The ADIM Status and Monitoring screen is displayed as  
Status, Monitoring  
shown in Figure 5.1.  
NOTE: The PC is pre-configured to automatically log into  
Windows NT and start the ADIM application. ADIM can be  
configured to automatically log in, bypassing the log in dialog.  
This allows automatic start up of the ADIM application when the  
PC is restarted.  
Figure 5.1  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. If it is a new document, or if the Allegiant system is not on-  
NOTE: The green Allegiant On-line (in the lower right corner)  
indicates ADIM is properly communicating with the Allegiant. It  
may take up to 20 seconds for communication to be established.  
line, select <Allegiant> <<Display Allegiant Document>>:  
6. Go to the DVR Configuration page to enter the values for  
each DVR. (See Section 6; Operation.)  
6
OPERATION  
Elements of the ADIM document window:  
Allegiant Document:  
Menu Bar  
Tool Bar ꢀ  
Tabs ꢀ  
6.1 DVR Configuration Page  
To edit any fields, first select the Edit button assigned to the  
DVR #.  
After the row is filled in, select Accept.  
5. Using the instructions in the Master Control Software For  
Windows, configure the communication parameters  
<<Transfer>> <<<Communication Setup>>>:  
Set the communication parameters for the Allegiant and press  
Go Online.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Items from DVR Configuration page  
NOTE for Allegiant model LTC 8500:  
All Allegiants EXCEPT the LTC 8500 display the ADIM  
messages on a third line above or below the two status lines.  
The LTC 8500 does not have a third line for these messages,  
however, the messages can be set to overwrite the Monitor  
Title display. To do this the monitors must be set to  
Monitor Title mode.  
ITEM  
Explained  
Default  
Identifies 1 to 800 Hi-Qs  
(Not changeable)  
Not  
applicable  
Hi-Q Number  
IP address  
000.000.000.000  
Primary  
Disabled  
Blank  
Hi-Q IP address  
Determines how the Hi-Q is  
configured into the system  
(Primary, Backup, Review)  
Primary, Monitor  
Review or Backup  
6.2.2 Auto-Login  
Enabled Status  
Used to bring a Hi-Q online  
Allegiant Input  
connected to Hi-Q  
MON A output  
Must be a valid logical camera  
number within the Allegiant  
document  
If the Enable Automatic Login checkbox is checked, upon start  
of the application, ADIM is automatically logged on with User  
Privileges.  
Hi-Q (Hi-Q) input  
number  
Physical inputs on the Hi-Q  
(Not changeable)  
Not  
Applicable  
6.2.3 Keyboard / Com Port Assignment  
Allegiant Logical  
Camera Number  
looped with primary is assigned to the physical input  
The logical camera number  
within the Allegiant system that  
Blank  
Blank  
Hi-Q input  
of the Primary Hi-Q  
The logical monitor output of  
the Allegiant that is assigned to  
the physical input of the backup  
Hi-Q  
Allegiant Logical  
monitor number  
connected to backup  
6.2 Other Configuration  
6.2.1 Allegiant Status Message Monitors  
Example: Connect keyboard 1 into physical port 1 on back of the  
serial hub (preconfigured as COM5), etc.  
Table  
Heading  
Explained  
Field Values  
Logical  
Keyboard  
Number  
ADIM  
Keyboard  
1 – 6  
1 – 256  
(See Section 4.3 for  
pre-configured values)  
• COM port OK (GREEN)  
• COM port not available (RED)  
Specify a  
com port  
for each  
keyboard  
COM  
Port  
The <Allegiant Status Message Monitors> area is used to  
specify the Allegiant monitors that will display ADIM warning  
and error messages. Enter the monitor number(s) separated by  
commas (monitor ranges are specified with dashes). The monitor  
number(s) must exist in the Allegiant Monitor Table.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6.3 Status and Monitoring Page  
Table Element  
Hi-Q number  
Hi-Q Type  
Explained  
Field Values  
Fixed field depending on where the Hi-Q  
is entered into the table  
1 - 800  
Determines configuration of the Hi-Q in the  
system  
Primary, Backup, Review Monitor  
(See Appendix E for more details)  
Primary:  
Indicates operational status of a Hi-Q:  
On-Line and operational (Green);  
Off-Line (Red);  
Back-up unit that is currently backing up  
a primary Hi-Q (Yellow)  
On-Line (Green),  
Off-Line (Red)  
Backup:  
Available (Green), Backing up a  
Primary Hi-Q (Yellow)  
Hi-Q Status  
Hi-Q Input Number  
Physical inputs on the Hi-Q.  
1 through 4  
If a Backup Hi-Q is Backing up a Primary Hi-Q, this  
field indicates the logical camera numbers that are  
being recorded by the backup Hi-Qs. For Primary  
Hi-Qs, this is simply the logical camera attached to  
the Hi-Q.  
Allegiant Logical Camera Number  
1- 9,999  
Field is gray when the associated Hi-Q is  
Off-Line, or if the Hi-Q is a Backup Hi-Q in the  
Available state.  
OK (green)  
NO Sync (red)  
Camera Status  
This can be used to perform maintenance or repair  
on a Hi-Q without loosing any recording. To  
manually switch cameras to backup Hi-Q, first  
select a Hi-Q, then press this button.  
BUTTON: Switch video from selected  
Primary Hi-Q to a Backup Hi-Q  
Frees up a Backup DVR that’s currently in use.  
This DVR can subsequently be used to backup  
another DVR. First, ensure that the primary Hi-Q  
is operating and On-Line, then select the Backup  
Hi-Q and press this button.  
BUTTON: Set Selected Backup Hi-Q  
to “Available”  
BUTTON: Silence Beep  
Silences the ADIM PC alarm (beep).  
Allows a user to manually add a message to the  
Event Log.  
BUTTON: Add Manual Event Message  
ADIM Messages  
Displays the most recent information, warning,  
and error events.  
The Open File dialog box is displayed.  
The log file names indicate the day.  
(See Figures 6.1a & 6.1b)  
BUTTON: Open Log File  
The lower right-hand corner of the screen  
indicates On/Off-Line status of the Allegiant.  
Green = On-Line  
Red = Off-Line  
Allegiant On-line  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 6.3a  
Figure 6.3b  
New Log files are created daily upon the occurrence of the  
NOTES:  
first event after 12:00am. Otherwise, new entries are  
appended to the existing log file upon starting the  
application.  
Log files are easily manipulated into MS Excel or MS Access  
files for reporting. Use the TAB-delimited option to import  
into other databases.  
Figure 6.4a  
6.4 Allegiant Camera Title Transfer Dialog  
Camera titles configured for your Allegiant may be transferred to  
the DVRs. Titles may be transferred in their entirety, or specific  
cameras may be selected. To transfer titles, from the pull-down  
FILE menu, select Allegiant from the menu, then select Allegiant  
Title Transfer, as shown in Figures 6.4a and 6.4b.  
NOTE: Allegiant camera titles must be downloaded to the  
Allegiant before they can be transferd to DVRs.  
Figure 6.4b  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SoftKey Display  
Status Display  
7
ADIM KEYBOARD OPERATION  
Numeric  
Entry Cell  
7.1 Product Menu  
SoftKey Descriptor  
To ensure that the IntuiKey  
Keyboard is properly connected  
to the ADIM system, press the  
IntuiKey’s Product key. The  
ADIM On-Line softkey option  
(see Figure 7.1) will only be  
displayed if the IntuiKey  
Keyboard is properly connected  
and configured, and the ADIM  
application is running.  
Camera  
Mon1itor  
1
Allegiant  
ADIM  
Exit  
MUX/DVR  
Keyboard  
Control  
Prod  
Mon  
^ Up  
Zoom  
Clr  
Shot  
< Left  
v Down  
Right >  
1
2
5
8
3
6
9
4
7
0
Press the ADIM On-Line  
softkey to bring up the  
Allegiant main menu. The  
ADIM Controls softkey is  
now displayed.  
Figure 7.1  
SoftKeys  
Numeric Keypad  
IntuiKey Components  
7.4 Joystick Operation  
NOTE: If ADIM is offline, the ADIM Controls softkey will not  
appear (will be blank on the IntuiKey Keyboard).  
When in ADIM Controls mode, the IntuiKey Joystick can be  
used for the following actions:  
7.2 Allegiant Main  
Menu  
Upon pressing the ADIM  
Controls softkey, the  
following occurs:  
Navigation of the Menus Screen of the DVRs (UP, DOWN,  
LEFT, RIGHT).  
Proportional Playback Speed (clockwise rotation for fast  
forward; counterclockwise rotation for fast reverse).  
Exit  
User  
Log Off  
Device  
Lockout  
Command  
Script  
Alarm  
Control  
Camera  
Control  
If the selected camera  
is found and the DVR is  
mapped and available,  
pre-recorded video from  
the present camera is  
Program  
Sequence Functions  
User  
7.5 Numeric Keypad Buttons  
When in ADIM Controls mode, the IntuiKey Keypad buttons  
perform the following functions:  
Load  
Sequence  
ADIM  
Controls  
Hold  
Start  
Sequence Sequence  
<Previous  
<Sequence Sequence>  
<Stop Stop>  
Next>  
Enter corresponds to the Hi-Q’s front panel OK or Select  
button.  
The 1, 2, 3, and 4 keypad buttons on the keyboard emulate  
the Hi-Q’s front panel buttons.  
displayed on the selected  
CCTV monitor. (The  
default pre-recorded time  
is 1-minute.) In addition,  
Figure 7.2  
the Keyboard displays the ADIM Controls menu (Figure 7.3). 7.6 Softkey Buttons  
If the requested camera or monitor is not mapped to a DVR  
(within the ADIM), the error message, Requested Device  
Not Found, (along with an audible beep) is displayed on the  
Keyboard.  
If the camera is found, but the DVR is in use by another  
operator, the error message, DVR in Use, (along with an  
audible beep) is displayed on the Keyboard.  
When in ADIM Controls mode, the IntuiKey softkeys perform  
the appropriate action for the specific DVR.  
The Exit button performs the following actions:  
Returns the DVR to the system (makes available for  
other users).  
Returns the keyboard to its previous menu.  
Returns the Live camera view (direct from the Allegiant) to  
the present monitor.  
Refer to Appendix E for more information.  
7.3 ADIM Controls Menu  
NOTE: Details regarding the functions of the other buttons  
may be found in the IntuiKey Keyboard and Philips DVR  
Instruction Manuals.  
The ADIM Controls menu  
is used to control the Hi-Q  
(DVRRT4, DVRRT4EP)  
from the IntuiKey Keyboard.  
Play/  
Search  
Exit  
7.7 Keyboard Error Handling  
Quad  
OSD  
Stop  
If the IntuiKey keyboard fails to communicate with the system,  
an error message, ADIM Communication Error (along with an  
audible beep) displays on the keyboard.  
Zoom  
Frame  
Advance  
Alarm  
List  
Pause  
Menu  
Okay  
7.8 Clearing ADIM Alarms  
1-Touch  
Alarm  
ADIM messages (see Appendix A) will be displayed on the  
assigned CCTV monitors. Ensure the keyboard is NOT in the  
ADIM Controls menu. Use the IntuiKey Keyboard’s CLR to  
clear ADIM Alarm messages.  
Alarm  
Clear  
Figure 7.3  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
TROUBLESHOOTING  
Problem  
Explanation / Resolution  
• Ensure that a null modem serial cable is connected between the IntuiKey keyboards and the serial  
hub.  
• Ensure that the appropriate communications port is properly configured for the serial hub.  
• Ensure that the serial hub is connected to the network switch with a straight-through Ethernet cable.  
• Ensure that the ADIM software computer is connected to the network switch with a straight-through  
Ethernet cable.  
Keyboards are not communicating with the ADIM  
Software  
NOTE: If the COM port light is green (OK), this confirms the ADIM software successfully opened the  
COM port. (The COM port exists and is not in use by another application.)  
Pressing ADIM Controls on the IntuiKey  
results in the Allegiant monitor displaying the output  
of the Hi-Q’s MON A in Live mode instead of  
Playback mode. (No error messages are displayed  
on the Allegiant monitor.)  
• Set the Hi-Q Recorder’s password to 1234.  
• Ensure that the ADIM software is up and running in normal operations mode.  
• Verify that the RS-232 cable from the keyboard to the serial hub is connected properly.  
• The keyboard may go off-line and lose communication with ADIM if excessive conducted power  
disturbance is present on the system’s serial and/or ethernet interfaces. To re-establish communication,  
first identify and remove the source of the disturbance, or protect the system’s serial and/or ethernet  
interfaces from the disturbance, and then close and restart the ADIM PC software.  
Keyboards display ADIM Off-line  
• Verify that the serial hub and ADIM PC is on the same network segment.  
Error Message 100  
The ADIM system has found the DVR associated with the keyboard user’s request, but another user is  
presently using the DVR.  
• Wait for the DVR to be released by the other user.  
DVR in Use is displayed on the IntuiKey keyboard  
when DVR Control is pressed on the IntuiKey  
keyboard  
The user has requested playback from a device (either a camera or monitor) that could not be found in  
the ADIM mapping tables.  
Error Message 101  
• Ensure that the ADIM mapping tables are correct.  
Requested Devices Not Found is displayed on the • Ensure that the DVR associated with the requested device is on-line.  
IntuiKey keyboard  
• Ensure that in the case of a camera not being found that the associated DVR is marked as a playback  
or backup DVR.  
• Ensure that in the case of a monitor not being found, the associated DVR is marked as a review DVR.  
Communications have failed between the ADIM PC software and the IntuiKey keyboards.  
• Verify that the ADIM software is still running.  
• Examine the Log file in the ADIM software to determine the reason for the communications failure.  
• Ensure that the keyboard is connected to the serial hub using a 9-pin null modem cable.  
• Ensure that the serial hub is turned on and functioning properly (consult the manual that came with  
serial hub).  
Error Message 102  
ADIM Communication Error is displayed on the  
IntuiKey keyboard  
• Ensure that the keyboard is connected to the same serial port as defined in the ADIM software.  
• Ensure that the ADIM system has associated a valid serial port to the keyboard.  
• Ensure that the ADIM software and PC is running properly.  
Error Message 103  
ADIM General Error is displayed on the IntuiKey  
keyboard  
The ADIM software wishes to gain attention of the user due to detection of an error.  
• Consult the ADIM software PC and associated log file.  
Error Message 104  
ADIM Mode Conflict Error is displayed on the  
IntuiKey keyboard  
The IntuiKey keyboard and ADIM software are not synchronized.  
No action is required; the keyboard and ADIM software will automatically synchronize.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX A – EVENT LOGS  
Log File  
Monitor  
Message  
Likely Source  
of Error Info  
Event  
Component  
Type  
Entry  
Type  
Component ID  
Log Message  
Primary or Review  
Hi-Q Failure  
Primary or  
Review Hi-Q  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
DVR Error!  
DVR Error!  
ADIM Software  
Error  
Error  
Error  
DVR Failure  
Primary or Review  
Hi-Q Disk Array  
Failure  
Primary or  
Review Disk  
Array  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
Hi-Q  
Disk Array Failure  
Backup DVR Failure  
Backup Hi-Q  
Failure  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
BU DVR Error ADIM Software  
Backup Hi-Q  
Backup Hi-Q Disk  
Array Failure  
Backup Disk  
Array  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
BU DVR Error  
Hi-Q  
Hi-Q  
Hi-Q  
Error  
Info  
Disk Array Failure*  
Indicated DVR disabled  
Indicated DVR Enabled  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
Hi-Q Disabled  
Hi-Q Enabled  
ADIM Software  
ADIM Software  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
Info  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
Hi-Q On-line  
Hi-Q Off-line  
ADIM Software  
ADIM Software  
Hi-Q  
Hi-Q  
Info  
Info  
Indicated DVR on-line  
Indicated DVR off-line  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
ADIM Computer,  
IP Address:  
XXX.XXX.XXX.XXX  
Log File Created  
ADIM Software ADIM Software  
ADIM Software ADIM Software  
Info  
Info  
Log file created  
ADIM Computer,  
IP Address:  
XXX.XXX.XXX.XXX  
Log File Opened  
for Append  
Log file opened for  
append  
Less than 500 Mbytes of  
free space remains on the  
PC hard disk – improper  
system operation may  
occur if the disk is  
ADIM Computer,  
IP Address:  
XXX.XXX.XXX.XXX  
PC Hard Disk  
Nearly Full  
PC Disk Low ADIM Software ADIM Software  
ADIM Software ADIM Software  
Warning  
allowed to fill up  
ADIM Computer,  
IP Address:  
XXX.XXX.XXX.XXX  
ADIM Software  
Started  
Info  
Info  
ADIM Software started  
User Name,  
User Number: XX  
Manual Event  
ADIM Software  
Hi-Q  
User  
Hi-Q  
User specified.  
Over-temperature  
Warning warning received from  
indicated Hi-Q  
Hi-Q Hi-Temp  
Warning  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
DVR Hi Temp  
DVR Lo Temp  
DVR Battery  
Under-temperature  
Warning warning received from  
indicated Hi-Q  
Hi-Q Lo-Temp  
Warning  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
Hi-Q  
Hi-Q  
Hi-Q  
Hi-Q  
Low battery warning  
Warning received from indicated  
Hi-Q  
Hi-Q Low Battery  
Warning  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
Disk Array disk failure  
detected – disk array  
operating in degraded  
Disk Array  
Degraded  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
Disk Array!  
Hi-Q  
Disk Array  
Warning  
mode*  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX A – EVENT LOGS (…continued)  
Log File  
Entry  
Monitor  
Message  
Likely Source  
of Error Info  
Event  
Component  
Type  
Component ID  
Log Message  
Type  
Allegiant On-Line  
Allegiant Off-Line  
ADIM Software  
ADIM Software  
Allegiant  
Allegiant  
Allegiant  
Allegiant  
Info  
Allegiant went On-Line  
Allegiant went Off-Line  
Info  
Voltage out of spec  
warning received from  
indicated Hi-Q  
Hi-Q Low Power  
Supply Voltage  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
DVR Voltage  
Hi-Q  
Hi-Q  
Warning  
Dark Alarm for indicated  
Logical Camera on DVR  
#nnnn, IP Address:  
XXX.XXX.XXX.XXX,  
DVR Camera X  
Camera Dark  
Alarm  
Dark  
CamXXXX  
Hi-Q  
Camera  
Logical Camera #  
Logical Camera #  
Warning  
Camera Sync Loss Alarm  
for indicated Logical  
Camera on DVR #nnnn,  
IP Address:  
XXX.XXX.XXX.XXX,  
DVR Camera X  
Camera Failure  
(Video Loss Alarm)  
Fail CamXXXX  
Hi-Q  
Hi-Q  
Hi-Q  
Camera  
Hi-Q  
Error  
Info  
Manual Alarm for  
indicated Logical Camera on  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX,  
DVR Camera X  
Manual Alarm  
Logical Camera #  
Auxiliary Alarm for  
indicated Logical Camera on  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX,  
DVR Camera X  
Auxiliary Alarm  
Camera  
Logical Camera #  
Keyboard n  
Info  
Keyboard  
Communication  
(consecutive bad  
checksums)  
Communication errors  
detected for indicated  
keyboard  
KBD Comms ADIM Software  
ADIM Software  
Keyboard  
Hi-Q  
Warning  
Info  
Hi-Q  
Communication errors  
detected for  
Communication  
(consecutive bad  
checksums)  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
indicated Hi-Q  
Hi-Q  
Communication  
Lost (no Q-Ping  
Response)  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
No response  
from indicated Hi-Q  
ADIM Software  
Hi-Q  
Info  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
DVR Disk Full  
Hi-Q  
Hi-Q  
Hi-Q  
Info  
Info  
Hi-Q internal disk full  
Recording status changed to  
Disabled for indicated  
Logical Camera on DVR  
#nnnn, IP Address:  
Recording Status  
Change 1  
Camera  
Logical Camera #  
XXX.XXX.XXX.XXX,  
DVR Camera X  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX A – EVENT LOGS (…continued)  
Log File  
Monitor  
Message  
Likely Source  
of Error Info  
Event  
Component  
Type  
Entry  
Type  
Component ID  
Log Message  
Recording status changed  
to Continuous for  
indicated Logical Camera  
on DVR #nnnn,  
IP Address:  
XXX.XXX.XXX.XXX,  
DVR Camera X  
Recording Status  
Change 2  
Hi-Q  
Hi-Q  
Camera  
Camera  
Logical Camera #  
Logical Camera #  
Info  
Info  
Recording status changed  
to Continuous with  
Audio for indicated  
Logical Camera on  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX,  
DVR Camera X  
Recording Status  
Change 3  
Recording status changed  
to Event Only for  
indicated Logical Camera  
on DVR #nnnn,  
IP Address:  
XXX.XXX.XXX.XXX,  
DVR Camera X  
Recording Status  
Change 4  
Hi-Q  
Camera  
Logical Camera #  
Logical Camera #  
Info  
Info  
Recording stopped;  
Encoder problem for  
indicated Logical Camera  
on DVR #nnnn,  
IP Address:  
XXX.XXX.XXX.XXX,  
DVR Camera X  
Recording Status  
Change 5  
Hi-Q  
Camera  
Hi-Q  
Timeout --  
Could not go On-Line  
with indicated Hi-Q  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
Hi-Q Timeout  
ADIM Software  
Info  
Info  
Timeout --  
Could not go On-Line  
with indicated Hi-Q  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
Hi-Q Delayed-OK  
ADIM Software  
ADIM Software  
Hi-Q  
Disk Array  
Not Found  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
Disk Array!  
Backup OK  
Disk Array  
Warning Disk Array not detected  
Successful switchover from  
DVR #nnnn, IP Address  
(of Backup DVR):  
XXX.XXX.XXX.XXX  
DVR nnnn, IP Address  
Info  
Hi-Q DVR  
Switchover  
ADIM Software  
Backup Hi-Q  
XXX.XXX.XXX.XXX to  
indicated Backup DVR  
Warning message to  
Hi-Q DVR  
Switchover  
Warning  
DVR #nnnn, IP Address  
(of Primary DVR):  
generate monitor message  
Warning  
Backup OK  
No Backup!  
Backup Hi-Q  
Primary Hi-Q  
ADIM Software  
ADIM Software  
to inform operator of  
switchover.  
XXX.XXX.XXX.XXX  
No backup DVR was  
available to backup failed  
DVR  
Hi-Q DVR No  
Backup Warning  
DVR #nnnn, IP Address:  
XXX.XXX.XXX.XXX  
Warning  
Info  
The backup DVR is set  
available from backing up  
state of DVR nnnn, IP  
Address (Primary DVR)  
XXX.XXX.XXX.XXX  
Hi-Q Backup  
DVR made  
available  
DVR #nnnn, IP Address  
(of Backup DVR):  
XXX.XXX.XXX.XXX  
ADIM Software  
ADIM Software  
Backup Hi-Q  
Manual Backup  
Switchover  
Selected  
Manual Switchover from  
DVR nnnn, IP Address  
XXX.XXX.XXX.XXX  
was selected  
ADIM Computer,  
IP Address:  
XXX.XXX.XXX.XXX  
ADIM  
Software  
Info  
nnnn = logical DVR number, no leading zeros  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX B TECHNICAL SPECS  
ADIM Components (included):  
Industrial PC: Rack-mount industrial-grade Pentium® PC,  
120 MB RAM (minimum), 8 GB hard drive  
(minimum),  
ACCSH01:  
(1) Ethernet Serial Hub  
RocketPort Serial Hub 8-Port  
Operating Temperature: 0 to 40°C  
Voltage: 100 - 240 Volts AC, 50 - 60 Hertz  
Dimensions: 6" x 9" x 2.5"  
CD-ROM drive, floppy drive, keyboard, mouse,  
10/100BaseT- compatible (RJ-45),  
(152 mm x 229 mm x 63.5 mm)  
Weight: 2 lbs., 5 oz., (.90 KG)  
including power supply  
Host Interface: Ethernet 10Base-T (10 Mbps),  
RJ-45  
keyboard/mouse rack-mount shelf, and  
Windows NT® 120/220 VAC, 50/60 Hz.  
Monitor:  
14-inch SVGA (including rack-mount  
hardware) 120/220, VAC, 50/60 Hz  
Network Addressing Supported:  
MAC (Media Access Control)  
IP (Internet Protocol)  
LTC 8506/00: (1) 10-foot Console Cable  
Ethernet Cable: (2) 25-foot Cables  
Agency Approvals: FCC Part 15 Class A  
UL/C-UL Listed CE Mark  
ACCNM015: (1) RS-232 Null Modem Cable, 15-foot  
Interface: Eight (8); DB9 Male, RS-232,  
RS-422 or RS-485 (selectable)  
Wiring diagram for the Serial Port’s RS-232 connections  
D9  
D9  
2
3
2
5
4
6
1
7
8
TD  
RD  
RD  
TD  
3
SG  
SG  
5
DTR  
DSR  
CD  
DTR  
DSR  
CD  
RTS  
CTS  
4
6
1
RTS  
CTS  
7
8
Figure 1: Null Modem Wiring Diagram  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX C – RECOMMENDED NETWORK SWITCHES  
Approved and tested network switches for use with ADIM.  
3Com SuperStack 4300 model  
APPENDIX D – LIST OF COMPATIBLE DVRS  
Hi-Q Series (DVRRT4, DVRRT4EP)  
APPENDIX E – PRIMARY, BACKUP, AND REVIEW DVRS  
Primary:  
DVRs on the input of the Allegiant  
Backup:  
DVRs used on the output of the Allegiant. When ADIM determines a problem with a Primary DVR, the cameras designated for that  
Primary DVR are switched over to the Backup DVR for recording.  
Review:  
DVRs used on the output of the Allegiant. These DVRs are used to record all video from a switched output of the Allegiant. The  
Review DVRs are useful when reviewing an incident/suspect that involved multiple cameras being switched to a specified Monitor. It  
is also useful to review alarm / event video from the output of the Allegiant.  
Using the Keyboard to Playback Video from the Review DVR:  
1. Select the Monitor you wish to review  
2. Select camera number that corresponds to the Hi-Q’s MON A output that is connected to the Allegiant Input. (In Figure  
below this would be camera number 29)  
29  
4
3
2
1
ALL
Monitor Outputs  
10  
11 12 13  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Windows® is a registered trademark of Microsoft Corporation.  
3935 890 42712 02-39  
© 2002 by Philips Electronics N.V.  
© 2002 by Philips Communication, Security & Imaging, Inc.  
All Rights Reserved. Philips® is a registered trademark of Philips Electronics N. A. Corp.  
Updated September 25, 2002. Data subject to change without notice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips CD Player 190B6CS User Manual
Philips Iron GC3390 User Manual
Philips Mouse HR4501C User Manual
Philips Portable DVD Player PET831 05 User Manual
Philips Stereo System MCM704D User Manual
Philips TV VCR Combo 14PV385 User Manual
Philips Washer AZ9002 User Manual
Pitco Frialator Fryer L20 281 User Manual
Powerware Network Card 1500 VA 60kVa User Manual
Presto Rice Cooker Rice Cooker User Manual