Register your product and get support at
HFL3008D/W
EN User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
be disconnected. When disconnecting
the power, always pull the power plug,
never the cord. Ensure that you have
full access to the power plug, power
cord and outlet socket at all times.
1 Important
Safety
Risk of damage to the TV!
Two people are required to lift and
carry a TV that weighs more than 25kg
or 55lbs.
When stand mounting the TV, use only
the supplied stand. Secure the stand to
the TV tightly. Place the TV on a flat,
level surface that can support the
combined weight of the TV and the
stand.
When wall mounting the TV, use only a
wall mount that can support the weight
of the TV. Secure the wall mount to a
wall that can support the combined
weight of the TV and wall mount. TP
Vision Netherlands B.V. bears no
responsibility for improper wall
mounting that result in accident, injury
or damage.
Precautions
Read and understand all instructions before
you use your TV. If damage is caused by
failure to follow the instructions, the
warranty does not apply.
Risk of electric shock or fire!
Never expose the TV to rain or water.
Never place liquid containers, such as
vases, near the TV. If liquids are spilled
on or into the TV, disconnect the TV
from the power outlet immediately.
Contact Philips Consumer Care to have
the TV checked before use.
Never place the TV, remote control or
batteries near naked flames or other
heat sources, including direct sunlight.
To prevent the spread of fire, keep
candles or other flames away from the
TV, remote control and batteries at all
times.
If you need to store the TV,
disassemble the stand from the TV.
Never lay the TV on its back with the
stand installed.
Before you connect the TV to the
power outlet, ensure that the power
voltage matches the value printed on
the back of the TV. Never connect the
TV to the power outlet if the voltage is
different.
Parts of this product may be made of
glass. Handle with care to avoid injury
and damage.
Never insert objects into the ventilation
slots or other openings on the TV.
Never expose the remote control or
batteries to rain, water or excessive
heat.
Avoid force coming onto power plugs.
Ensure that the power plug is fully
inserted into the power socket. Loose
power plugs can cause arcing or fire.
When the TV is swivelled, ensure that
no strain is exerted on the power cord.
Strain on the power cord can loosen
connections and cause arcing.
Risk of injury to children!
Follow these precautions to prevent the TV
from toppling over and causing injury to
children:
Never place the TV on a surface
covered by a cloth or other material
that can be pulled away.
Ensure that no part of the TV hangs
over the edge of the surface.
Never place the TV on tall furniture,
such as a bookcase, without anchoring
both the furniture and TV to the wall
or a suitable support.
To disconnect the TV from the mains
power, the power plug of the TV must
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Educate children about the dangers of
climbing on furniture to reach the TV.
Avoid stationary images as much as
possible. Stationary images are images
that remain onscreen for extended
periods of time. Stationary images
include onscreen menus, black bars,
time displays, etc. If you must use
stationary images, reduce screen
contrast and brightness to avoid screen
damage.
Risk of swallowing batteries!
The product/remote control may
contain a coin-type battery, which can
be swallowed. Keep the battery out of
reach of children at all times!
Risk of overheating!
Never install the TV in a confined
space. Always leave a space of at least 4
inches or 10 cm around the TV for
ventilation. Ensure that curtains or
other objects never cover the
Placement tips
Position the TV where light does not
shine directly on the screen.
The ideal viewing distance of this TV is
three times its diagonal screen size. For
example, if the diagonal screen size of
the TV is 81 cm / 32", the ideal viewing
distance is ~2.5 m / ~92" from the
front of the screen.
ventilation slots on the TV.
Risk of injury, fire or power cord damage!
Never place the TV or any objects on
the power cord.
Disconnect the TV from the socket and
aerial before lightning storms. During
lightning storms, never touch any part
of the TV, power cord or aerial cable.
While seated, your eyes should be level
with the centre of the screen.
TV placement
Risk of hearing damage!
You can apply the best sound settings for
your TV by selecting the TV placement (wall
mount or stand mount).
Avoid using earphones or headphones
at high volumes or for prolonged
periods of time.
1. Press
.
Low temperatures
If the TV is transported in temperatures
2. Select [Setup], then press OK.
3. Select [TV settings] > [General settings]
or [TV placement].
below 5°C or 41°F, unpack the TV and
wait until the TV temperature matches
room temperature before connecting
the TV to the power outlet.
4. Select [On a TV stand] or [Wall
mounted], then press OK.
Care
Screen
Risk of damage to the TV screen!
Never touch, push, rub or strike the
screen with any object.
Unplug the TV before cleaning.
Clean the TV and frame with a soft
damp cloth and wipe gently. Never use
substances such as alcohol, chemicals or
household cleaners on the TV.
To avoid deformations and colour
fading, wipe off water drops as soon as
possible.
EN
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TP Vision Netherlands B.V. cannot be held
responsible neither for any errors in the
content of this document nor for any
problems as a result of the content in this
document. Errors reported to Philips will be
adapted and published on the Philips support
website as soon as possible.
Lock the TV
Your TV is equipped with a Kensington
security slot at the base of the TV. To secure
the TV, purchase a Kensington anti-theft lock
(sold separately).
Terms of warranty
Risk of injury, damage to TV or void of
warranty! Never attempt to repair the
TV yourself.
Use the TV and accessories only as
intended by the manufacturer.
The caution sign printed on the back of
the TV indicates risk of electric shock.
Never remove the TV cover. Always
contact Philips Customer Care for
service or repairs.
Any operation expressly prohibited in
this manual, or any adjustments and
assembly procedures not
recommended or authorised in this
manual, shall void the warranty.
Pixel characteristics
Legal
This LCD/LED product has a high number of
colour pixels. Although it has effective pixels
of 99.999% or more, black dots or bright
points of light (red, green or blue) may
appear constantly on the screen. This is a
structural property of the display (within
common industry standards) and is not a
malfunction.
Notice
2013 © TP Vision Netherlands B.V. All rights
reserved. Specifications are subject to change
without notice. Trademarks are the property
of Koninklijke Philips Electronics N.V or their
respective owners. TP Vision Netherlands
B.V. reserves the right to change products at
any time without being obliged to adjust
earlier supplies accordingly.
CE compliance
This product is in compliance with the
essential requirements and other relevant
provisions of Directives 2006/95/EC (Low
Voltage), 2004/108/EC (EMC) and
2011/65/EU (ROHS).
The material in this manual is believed
adequate for the intended use of the system.
If the product, or its individual modules or
procedures, are used for purposes other
than those specified herein, confirmation of
their validity and suitability must be obtained.
TP Vision Netherlands B.V. warrants that the
material itself does not infringe any United
States patents. No further warranty is
expressed or implied.
Compliance with EMF
TP Vision Netherlands B.V. manufactures
and sells many products targeted at
consumers which, like any electronic
apparatus, in general have the ability to emit
and receive electromagnetic signals.
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
One of Philips’ leading Business Principles is
to take all necessary health and safety
measures for our products, to comply with
all applicable legal requirements and to stay
well within the Electro Magnetic Field (EMF)
standards applicable at the time of producing
the products.
Manufactured under licence from Dolby
Laboratories. Dolby and the double D
symbol are trademarks of Dolby
Laboratories.
Philips is committed to develop, produce
and market products that cause no adverse
health effects. TP Vision confirms that, as
long as its products are handled properly for
their intended use, they are safe to use
according to scientific evidence available
today.
The terms HDMI and HDMI High-Definition
Multimedia Interface and the HDMI Logo are
trademarks or registered trademarks of
HDMI Licensing LLC in the United States
and other countries.
Philips plays an active role in the
Kensington and Micro Saver are registered
US trademarks of ACCO World
Corporation with issued registrations and
pending applications in other countries
throughout the world.
development of international EMF and safety
standards, enabling Philips to anticipate
further developments in standardisation for
early integration in its products.
Open source
This product contains software licensed
under an open-source licence. For
Covered by one or more of the following
U.S. patents: 7,295,673; 7,460,668;
7,515,710; 7,519,274.
DivX®, DivX Certified® and associated logos
are trademarks of Rovi Corporation or its
subsidiaries and are used under licence.
acknowledgments and licence texts, please
refer to the electronic in-product user
manual. TP Vision Netherlands B.V. hereby
offers to deliver, upon request, a copy of the
complete corresponding source code for the
copyrighted open source software packages
used in this product for which such offer is
requested by the respective licences.
DivX Certified® to play DivX® video up to
HD 1080p, including premium content.
ABOUT DIVX VIDEO: DivX® is a digital
video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an
official DivX Certified® device which has
passed rigorous testing to verify that it plays
DivX video. Visit divx.com for more
information and software tools to convert
your files into DivX videos.
This offer is valid up to three years after
product purchase to anyone in receipt of this
information. To obtain source code, please
send your request in English with product
number to:
"Intellectual Property Department, TP Vision
Netherlands B.V., P.O. Box 80077, 5600 KA
Eindhoven, The Netherlands."
ABOUT DIVX VIDEO-ON-DEMAND: This
DivX Certified® device must be registered in
order to play purchased DivX Video-on-
Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD
section in your device setup menu. Go to
vod.divx.com for more information on how
to complete your registration.
Trademarks and copyrights
Windows Media is either a registered
trademark or trademark of Microsoft
Corporation in the United States and/or
other countries.
EN
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch off inactive devices: Switch off
connected EasyLink HDMI-CEC
(Consumer Electronic Control)
compliant devices that are inactive.
While you watch TV, press the Green
button and select [Inactive devices off].
Power management: An advanced
power management helps save the
energy consumed by this TV. To view
how your personalised TV settings
affect the TV's relative power
consumption, press , then select
[Setup] > [Watch demos] > [Active
Control demo].
PlayReady Final Products
Content owners use Microsoft PlayReady™
content access technology to protect their
intellectual property, including copyrighted
content. This device uses PlayReady
technology to access PlayReady protected
content and/or WMDRM-protected content.
If the device fails to properly enforce
restrictions on content usage, content
owners may require Microsoft to revoke the
device’s ability to consume PlayReady-
protected content. Revocation should not
affect unprotected content or content
protected by other content access
technologies. Content owners may require
you to upgrade PlayReady to access their
content. If you decline an upgrade, you will
not be able to access content that requires
the upgrade.
Recycling
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
All other registered and unregistered
trademarks are the property of their
respective owners.
Sustainability
Energy efficiency
This TV is designed with energy-efficient
features. To access these features, press the
Green button on the remote control.
When this crossed-out wheeled bin symbol
is attached to a product it means that the
product is covered by the European
Directive 2002/96/EC. Please inform yourself
about the local separate collection system
for electrical and electronic products.
Energy saving picture settings: You can
apply a combination of energy saving
picture settings. While you watch TV,
press the Green button and select
[Energy saving]. Then select the
[Energy saving] picture setting.
Screen off: If you only want to listen to
audio from the TV, you can switch off
the TV display. Other functions
continue to operate normally. While
you watch TV, press the Green button
and select [Screen off].
Auto switch off: To conserve energy,
set the TV to switch off automatically
after a period of inactivity. While you
watch TV, press the Green button and
select [Auto switch off]. Then select
the period after which the TV switches
off.
Please act according to your local rules and
do not dispose of your old products with
your normal household waste. Correct
disposal of your old product helps to
prevent potential negative consequences for
the environment and human health.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed of with normal
household waste. Please inform yourself
about the local rules on separate collection
of batteries because correct disposal helps to
prevent negative consequences for the
environment and human health.
Use the Philips connectivity guide
An easy-to-use connectivity guide gives you
guidance on how to connect your TV to
other devices. Visit
Search the TV forum
Your question may have already been
answered by the Philips TV community of
Contact Philips
You can contact Philips Consumer Care in
your country for support. The number is
available in the leaflet accompanying this
product or online at
Energy label
Before you contact Philips, write down the
model and serial number of your TV. You
can find this information on the back of your
TV or on the TV packaging.
The European Energy Label informs you on
the energy efficiency class of the product.
The greener the energy efficiency class of
this product is, the lower the energy it
consumes.
On the label, you can find the energy
efficiency class, the average power
consumption of the product in use and the
average energy consumption for 1 year. You
can also find the power consumption values
for the product on the Philips website for
Help and support
Visit the Philips website
Visit the Philips support website at
On the Philips support website, you can also:
Find answers to Frequently Asked
Questions (FAQ)
Download a printable PDF version of
this user manual
Email us a specific question
Chat online with Philips Consumer
Care (available in certain countries
only)
EN
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Remote control sensor
2 Use your TV
Point the remote control at the sensor.
Make sure that the line of sight between the
remote control and the TV is not blocked.
TV controls
Remote control
Rear controls
1. (Standby): Switch the TV on or to
standby.
2. MyChoice: Access customised menu.
3. CLOCK: Access the TV clock.
4.
ThemeTV: Access ThemeTV options.
5.
TV: Switch source to watch TV.
1. (Standby): Switch the TV on or off.
2. CH +/-: Switch to the next or previous
channel.
3.
(SOURCE): Watch a connected
device.
4.
+/- (Volume): Increase or decrease
volume.
6.
CHANNEL GRID: View the TV
channel list.
Sensors and indicators
7.
SOURCE: Watch a connected device.
8. GUIDE: Access TV guide.
9.
FORMAT: Change picture format.
10. (Home): Access the Home menu.
11. OK: Confirm an entry or selection.
12.
(Navigation buttons): Navigate
through menus and select items.
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
EasyLink controls
If you connect your TV to HDMI-CEC
enabled devices, such as a Blu-ray player or
home theatre, you can control them at the
same time with one remote control. Simply
switch on EasyLink after connection.
Read more about Easylink in Connect your
TV > Set up Easylink devices > Control
13. LIST: Access the TV channel list.
14. ADJUST: Adjust TV settings.
On-screen remote control
You can also control connected HDMI-CEC
enabled devices through other buttons that
are available through the on-screen remote
control. Make sure that Easylink is switched
on after connection. Read more about
Easylink in Connect your TV > Set up
Easylink devices > Control devices (Page
15.
INFO: Display information about
current activity.
16. OPTIONS: Access currently available
options, picture and sound menus.
To access the on-screen remote control
1. While you watch a connected device,
press OPTIONS.
2. Select [Show remote control], then press
OK.
3. Select an on-screen button, then press
OK.
17. (Back): Return to the previous menu
page or exit from a TV function.
18. CH - / CH +: Change channels.
19. +/-(Volume): Adjust volume.
20. (Mute): Mute or restore audio.
Watch TV
Switch TV on or off
21. Colour buttons: Select tasks or options.
22. SUBTITLE: Enable or disable subtitles.
23. 0-9 (Numeric buttons): Select TV
channels or enter text.
24. TEXT: Enable or disable text.
EN
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch the TV on
Adjust TV volume
Connect the TV to the mains outlet
and switch on the main power.
If the TV is not switched on, the
standby LED remains off. Press on
the TV.
If the standby LED is lit, press on the
remote control.
Note: There is a short delay before the TV
responds.
Tip: If you cannot find your remote control
and want to switch on the TV from standby,
press any button the TV.
Switch TV to standby
Press on the remote control.
The standby LED on the TV switches to red.
Switch off the TV
Increase or decrease the TV volume
Press on the TV.
The standby LED switches to off.
Press +/- on the remote control.
Press +/- on the TV.
Note: Though your TV consumes very little
energy when it is in standby or switched off,
it does use some energy. If you are not going
to use the TV for an extended period of
time, disconnect the TV from the mains plug.
Mute or restore the TV volume
Press
mute the volume.
Press again to restore the volume.
on the remote control to
Automatic switch off
Adjust headphone volume
1. Press
2. Select [Setup] > [TV settings] > [Sound]
> [Headphone volume], then press OK.
3. Select a level.
You can save energy with this TV's energy
efficiency settings, which are enabled by
default. If there is no user interaction (such
as pressing a remote control button or a
control on the TV) for four hours, the TV
will automatically switch to standby.
To disable automatic switch off
1. While you watch TV, press the Green
button on the remote control.
.
Switch TV channels
2. Select [Auto switch off], then press OK.
3. Use the Navigation buttons to select [0
mins], then press OK.
EN
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Press CH +/- on the remote control or
TV.
Press the Numeric buttons to enter a
[Free channels]: Display only free
channels.
[Scrambled channels]: Display only
channel number.
scrambled channels.
Note: The filtering options may vary
according to your broadcaster.
Manage favourite channels
You can view all channels or only a list of
your favourite channels.
Switch between antenna and cable channels
You can switch between antenna and cable
channels while you are watching TV.
Create a list of your favourite channels
1. While you watch TV, press
.
1. Press LIST.
2. Select [Setup] > [Channel settings] >
[Channel installation] > [Antenna
connection].
The channel list is displayed.
2. Select the channel to mark as favourite,
then press OPTIONS.
3. Select [Antenna (DVB-T)] to watch
antenna channels or [Cable (DVB-C)] to
watch cable channels, then press OK.
3. Select [Add/remove favourites], then
press OK.
The selected channel is marked with an
asterisk.
Rename channels
When you select a channel, its name
appears. You can change this channel name.
To remove a channel from the favourites list,
select [Add/remove favourites], then press
OK.
1. While you watch TV, press LIST.
The channel list is displayed.
2. Select the channel to rename, then select
OPTIONS.
Display your list of favourite channels
1. Press LIST, then press OPTIONS.
2. Select [List] > [Favourites] to display
channels in the favourite list.
3. Select [Rename], then press OK.
The onscreen keyboard is displayed.
4. Press the Navigation buttons to select
each character, then press OK.
5. Once complete, select [Done], then press
OK to confirm.
3. Press OK to confirm.
Manage channel lists
After the channels are installed, you can:
Filter channels.
Switch between antenna and cable
channels.
Reorder channels
After the channels have been installed, you
can reorder the channel list.
Rename channels.
Reorder channels.
Lock a channel.
1. While you watch TV, press LIST.
The channel list is displayed.
2. Press OPTIONS.
Listen to digital radio.
3. Select [Reorder], then press OK.
Filter channels
4. Select the channel to reorder, then press
OK.
5. Press the Navigation buttons to move the
highlighted channel to another location, then
press OK.
6. Once complete, press OPTIONS.
7. Select [Exit reorder], then press OK.
1. While you watch TV, press LIST.
2. Press OPTIONS, then select [Filter].
3. Select an option, then press OK.
[Digital + Analogue]: Display all
channels in the channels list.
[Digital TV channels]: Display only
digital channels.
[Analogue Channels]: Display only
analogue channels.
Lock a channel
You can prevent unauthorised access to
channels by locking them.
[Free + scrambled]: Display all channels
in the channels list.
EN
12
Download from Www.Somanuals.com. All Manuals Search And Download.
1. While you watch TV, press LIST.
[Vivid]: Rich and dynamic settings, ideal
The channel list is displayed.
2. Select the channel to lock, then press
OPTIONS.
for daytime viewing.
[Natural]: Natural picture settings.
[Standard]: Default settings that suit
most environments and types of video.
[Movie]: Ideal settings for movies.
[Photo]: Ideal settings for photos.
[Energy saving]: Settings that conserve
the most energy.
3. Select [Lock channel], then press OK.
4. If prompted, enter the PIN code.
The channel is marked with a lock icon in
the channel list.
Tip: To watch a locked channel, enter the
PIN code when prompted.
Listen to digital radio
If digital radio channels are available, you can
listen to them. They are installed
automatically when you install the TV
channels.
Select your preferred sound settings
1. While you watch TV, press OPTIONS.
2. Select [Picture and sound] > [Sound
style], then press OK.
3. Select an option, then press OK:
[Personal]: Apply your personalised
sound settings.
[Original]: Settings that suit most
environments and types of audio.
[Movie]: Ideal settings for movies.
1. While you watch TV, press LIST.
The channel list is displayed.
2. Press OPTIONS.
3. Select [Filter] > [Radio], then press OK.
4. Select a radio channel, then press OK.
[Music]: Ideal settings for listening to
music.
[Game]: Ideal settings for games.
[News]: Ideal settings for spoken audio,
such as the news.
Watch connected devices
Before you can watch a device, connect the
device to the TV. See Connect your TV >
Select a device with SOURCE
Change picture format
You can change the picture format to suit
the video source.
1. Press
SOURCE.
2. Select a device, then press OK.
Select a device from the Home menu
1. Press
FORMAT.
1. Press
.
2. Select a picture format, then press OK.
2. Select [Source], then press OK.
The available picture formats depend on the
video source:
3. Select the device, then press OK.
To add or manage your connected devices,
see Connect your TV > Watch connected
[Auto fill]: Adjust the picture to fill the
screen (subtitles remain visible).
Recommended for minimal screen
distortion but not for HD or PC.
[Auto zoom]: Enlarge the picture to fill
the screen. Recommended for minimal
screen distortion but not for HD or PC.
[Super zoom]: Remove the black bars
on the sides of 4:3 broadcasts. Not
recommended for HD or PC.
Use picture and sound presets
Your TV comes with predefined picture and
sound settings. You can apply these settings
or customise them.
Select your preferred picture settings
1. While you watch TV, press OPTIONS.
2. Select [Picture and sound] > [Picture
style], then press OK.
[Movie expand 16:9]: Scale 4:3 format
to 16:9. Not recommended for HD or
PC.
3. Select an option, then press OK:
[Personal]: Apply your personalised
picture settings.
EN
13
Download from Www.Somanuals.com. All Manuals Search And Download.
[Wide screen]: Shows widescreen
format content unstretched. Not
recommended for HD or PC.
[Unscaled]: Provide maximum detail for
PC. Only available when PC mode is
selected in the Picture menu.
[Search by genre]: Search programmes
by genre.
[All reminders]: Display a list of all
programme reminders.
Play multimedia files
[4:3]: Display the classic 4:3 format.
What you can do
You can play videos, photos and music on
your TV from a USB device connected to
the TV.
View programme guide
What you can do
You can view channel schedules and
Play files from USB device
If you have photos, videos or music files on a
USB storage device, you can play the files on
TV.
programme synopses for digital TV channels
using programme guides provided by the
broadcasters. The availability of programme
guides is dependent on your broadcaster.
You cannot view a channel's programme
guide information if:
Caution:
TP Vision is not responsible if the USB
hard drive is not supported, nor is it
responsible for damage to or loss of
data in the device.
the age rating of the channel is equal or
higher than the age rating set on your
TV.
the channel is locked.
Do not overload the USB port. If you
connect a USB storage device that
consumes more than 500mA power,
make sure that it is connected to its
own external power supply.
From the broadcaster
Access broadcaster programme guide
1. Press
.
2. Select [TV guide], then press OK.
Browse USB device
1. Connect the USB device to the USB
connector on the TV.
3. If you are viewing the programme guide
for the first time, follow the onscreen
instructions to update the guide.
Customise broadcaster programme guide
You can customise the displayed information
to:
2. Press
SOURCE, select [USB], then
press OK.
3. Select a file from the content browser,
then press OK to start play.
4. Press OK to control play.
5. Optional: To select a different USB device,
select [USB device] at the bottom of the TV
Remind you when programmes start.
Display only preferred channels.
Change day of display.
screen.
Note: Options may vary according to the
programme information available from the
broadcaster.
Tips:
Select the top bar to filter your files by
type.
Select [Sort] to arrange the files by
1. In the programme guide, press
OPTIONS.
2. Select an option, then press OK:
name, date or other fields.
[Acquire EPG data]: Update
programme guide information.
[Change day]: Select the day to display
programme guide.
EN
14
Download from Www.Somanuals.com. All Manuals Search And Download.
To pause the track, press OK.
Press OK again to resume playback.
To skip forward or backward 10
seconds, press or .
To stop the video or exit the content
Play options
Watch video
1. Select in the top bar.
2. Select a video, then press OK.
3. Optional: To play all the videos in a folder,
select a video, then select [Play all].
browser, press
.
Music options
While you play music, press OPTIONS,
then press OK to select an option:
To skip to the next or previous video,
press CH+ or CH -.
To pause the video, press OK.
Press OK again to resume playback.
[Repeat]: Select [Repeat] to play a
track or an album repeatedly, or select
[Play once] to play a track once.
[Shuffle on] / [Shuffle off]: Enable or
disable random play of tracks.
To skip forward or backward 10
seconds, press or .
To stop the video or exit the content
browser, press
.
Note:
Video options
While you play video, press OPTIONS,
then press OK to select an option:
To view information about a song (for
example, title, artist or duration), select the
song, then press
To hide the information, press
again.
View photos
1. Select in the top bar.
2. Select a photo thumbnail, then pressOK.
INFO.
[Subtitles]: Select the available subtitle
settings.
[Subtitle language]: Select the language
INFO
for subtitles if available.
[Character set]: Select the correct
character set for the subtitles.
[Audio language]: Select an audio
language.
Start a slideshow
If there are multiple photos in a folder, select
a photo, then select [Slideshow].
[Repeat]: Select [Repeat] to play the
video file repeatedly or [Play once] to
play the video file once.
To skip to the next or previous video,
press CH+ or CH -.
To stop the slideshow or close the
photo, press LIST.
[Shuffle on] / [Shuffle off]: Enable or
disable random play of video files.
[DivX® VOD]: Display the DivX
registration and deregistration codes for
this TV.
Slideshow options
While you play a slideshow, press
OPTIONS, then press OK to select an
option:
Note:
[Shuffle off] / [Shuffle on]: Enable or
disable random display of pictures in
the slideshow.
[Repeat]: Select [Repeat] watch a
slideshow repeatedly or [Play once] to
watch once.
[Slideshow time]: Select the display
time for each photo in the slideshow.
[Slideshow transitions]: Select the
transition from one photo to the next.
To view information about a video (for
example, played position, duration, title or
date), select the video, then press
To hide the information, press
again.
INFO.
INFO
Listen to music
1. Select in the top bar.
2. Select a track, then press OK.
3. Optional: To play all the tracks in a folder,
select a track, then select [Play all].
To skip to the next or previous track,
press CH+ or CH-.
EN
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Hotel information page
3 Use more of
your TV
Display a welcome logo
You can create a welcome logo with images
such as your hotel's logo.
1. Create a welcome screen in .png format
and save the file to a USB storage device.
2. Connect the USB storage device to the
TV, then switch on the TV.
Professional mode
3. In the professional setup menu, select
What you can do
With professional mode, you can configure
this TV for commercial use. This includes
features such as:
[Welcome logo] > [USB to TV].
4. Select [Welcome logo] > [Display logo]
> [On] to display the logo.
Display a welcome message
Blocking guests from modifying the TV
channels or settings
You can create and display a welcome
message for your guests. The message can
consist of up to two lines of text, each
containing a maximum of 20 alphanumeric
characters.
Programming the TV to switch on to a
specific channel and volume
Limiting the maximum volume
Blocking specific channels
Locking buttons on the remote control
Controlling on-screen information
1. In the professional setup menu, select
[Welcome message] > [Display message] >
[On].
Note: In professional mode, most of the
mainstream features are replaced by similar
features for commercial use.
2. Select a setting to change:
[Line 1] / [Line 2]: Enter the content
for the welcome message.
[Clear]: Clear [Line 1] and [Line 2].
[Message Time-out]: Set how long to
display the message.
Access professional-mode settings
1. Press on the remote control.
2. Press 3, 1, 9, 7, 5, 3,
.
3. Press OK to display the on-screen
keyboard and use the Navigation buttons to
compose the welcome message.
The professional setup menu appears.
Switch on professional mode
1. In the professional setup menu, select
[Professional Settings] > [Professional
mode].
Display a hotel information screen
You can create and display static information
screens about your hotel. The information
page appears as an icon in the home menu,
when you switch on the TV, and can also be
2. Select a setting to change, then press OK:
[On]: Switch on professional mode.
Hospitality features are enabled.
[Off]: Switch off professional mode.
The TV operates as a normal consumer
TV.
accessed by pressing
INFO.
1. Create an information screen in .jpg
format and save the file to a USB storage
device.
2. Connect the USB storage device to the
TV, then switch on the TV.
3. Press to store all professional mode
settings and exit.
4. Restart the TV.
3. In the professional setup menu, select
[Hotel information] > [USB to TV].
Display hotel information
You can store and display information about
your hotel on TV sets, such as:
4. Select [Hotel information] > [Display
information] > [On] to display the hotel
information.
Welcome logo
Welcome message
EN
16
Download from Www.Somanuals.com. All Manuals Search And Download.
To view the hotel information screen by
pressing INFO, in the professional setup
menu, select [Hotel information] > [Info
[ThemeTV]: Enable or disable Theme
TV.
[SmartPay]: Enable or disable SmartPay.
key enable] > [On].
Pairing TVs with a remote control
You can pair a TV with up to ten remote
controls.
Change professional mode settings
Professional mode settings
Use professional-mode settings to speed up
installation of your TV for commercial use.
1. In the professional setup menu, select
[Installation] > [Multi remote control].
2. Select an option from [TV0] to [TV9] to
identify the paired remote control, then
press OK.
3. To set the remote control in a specific
mode, simultaneously press and a number
key for 5 seconds to set the remote control
in the [TV0] to [TV9] mode.
1. In the professional setup menu, select
[Professional Settings], then press OK.
2. Select a setting to change, then press OK:
[Room ID]: Set a Room ID for the TV.
[Consumer setup]: Shortcut to the full
TV menu to configure all the TV
settings.
Note:
[Channel setup]: Shortcut to channel
list where you can re-arrange, rename
and hide channels.
[USB to TV]: Clone settings stored on
a USB storage device from another
Philips TV to your TV.
[TV to USB]: Copy your TV's settings
to a USB storage device. These settings
can be cloned onto another Philips TV.
[RF to TV]: Copy settings from a Philips
TV using RF signal.
Press and hold OK on a remote
control for more than five seconds. The
TV displays the TV ID (for example,
[TV0]) as well as the ID of the
transmitting remote control.
If the batteries in the remote control
are replaced after pairing, you will need
to pair the remote control with your
TV again to assign an ID to your TV.
Power-on settings
Customise the way the TV behaves when it
is switched on.
[Reset]: Reset all professional mode
settings to the factory default.
1. In the professional setup menu, select
[Switch on setting].
2. Select a setting to change, then press OK:
Installation settings
Use these settings to configure installation
settings.
[Switch on channel]: Select a channel
to display when the TV is switched on.
[Switch on vol]: Select the volume of
the speakers to be used when the TV is
switched on.
1. In the professional setup menu, select
[Installation].
2. Select a setting to change, then press OK:
[Blank channel]: Select a channel to
play audio only.
[Auto channel update]: Update
[Max volume]: Limit the maximum
volume of the TV.
[Switch on picture format]: Select a
channels automatically.
[Auto software update]: Update your
TV software automatically.
[Skip scrambled signals]: Enable or
disable scrambled channels in the
channel list.
picture format to be used when the TV
is switched on. If the source does not
support the pre-defined format, [Auto
fill] is enabled.
[Power on]: Select the mode to be
[Multi remote control]: Select an
option to identify a paired remote
control.
used when the TV is switched on:
- [On]: If the mains power is switched
on, the TV automatically switches on.
- [Standby]: If the mains power is
[MyChoice]: Enable or disable
MyChoice channels.
EN
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Enable SCART
switched on, the TV automatically
switches to standby.
- [Last status]: If the mains power is
switched on, the TV automatically
switches to the last status (i.e. on or to
standby).
Use this feature to control the TV through a
connected SCART device. When the
SCART device is switched on, the TV
automatically switches on.
1. Switch on the TV and the connected
SCART device.
2. In the professional setup menu, select
[Control settings] > [Auto SCART] >
[Power on scart], then press OK.
[Smart power]: Enable or disable
energy saving mode.
Load clock
In Professional mode, you can set the local
time according to the broadcast channel or
country. For general clock features, see Use
more of your TV > Set locks and timers >
Enable HDMI-CEC
If your TV is connected to HDMI devices
that are HDMI-CEC compliant, control these
devices with the TV's remote control. For
more details on how to use HDMI-CEC, see
Connect your TV > Set up EasyLink
1. In the professional setup menu, select
[Clock setup].
2. Select a setting to change, then press OK:
[Download program]: Select a channel
to download the clock settings.
[Country selection]: Select a country
for the local time to be based on.
[Time offset]: Select the number of
hours to offset.
1. Switch on the TV and all connected
HDMI-CEC devices.
2. Press
.
2. Select [Setup] > [TV settings] >
[EasyLink] > [On], then press OK.
3. In the professional setup menu, select
[Control settings] > [HDMI-CEC IN] >
[On], then press OK.
Combine channel list
In Professional mode, you can create an
integrated channel list comprising of
broadcast channels, connected devices and
multimedia files from a USB storage drive.
Channels are named based on the TV
connector or the media file name.
Enable or disable access to a USB storage
device
1. In the professional setup menu, select
[Control settings] > [Enable USB].
2. Select [On] or [Off], then press OK.
1. In the professional setup menu, select
[Combine channel list].
2. Select a setting to change, then press OK:
Direct USB access
You can set the TV to automatically display
the contents of a USB storage device when
the device is connected.
[AV]: Add connected devices to the
channel list.
1. In the professional setup menu, select
[Control settings] > [USB break-in] >
[On], then press OK.
[Media]: Add multimedia files to the
channel list.
Change other control settings
Control user access
You can control user access to the TV with
the following features:
1. In the professional setup menu, select
[Control settings].
2. Select a setting to change, then press OK:
Lock remote control buttons
Limit access from USB, HDMI-CEC or
SCART connectors
[Lock KB lock]: Select [On] to lock all
TV buttons except . Select [Off] to
unlock all buttons. Select [All] to lock
all buttons.
Customise guest view
EN
18
Download from Www.Somanuals.com. All Manuals Search And Download.
[RC lock]: Select [On] to disable all
[Independent main speaker mute]: This
buttons on the remote control. Note
that you can still enter the professional
setup menu by pressing 3, 1, 9, 7, 5, 3,
setting is only available if the TV
speaker is enabled.
- [On]: Control the TV speaker and
headphone volume separately. You can
only mute the TV volume.
- [Off]: Control both TV speaker and
.
[OSD display]: Select [On] to enable
on-screen information.
headphone volume together.
[High security]: Select [On] to restrict
access to the professional setup menu.
[Enable teletext]: Select [On] to
enable text.
[Enable MHEG]: Select [On] to enable
MHEG channels. Applicable to UK only.
[Enable EPG]: Select [On] to enable
the electronic programme guide.
[Enable subtitle]: Select [On] to enable
subtitles.
[Default main speaker volume]: If the
TV speaker and headphone volume are
controlled separately, you can set the
volume range to avoid sudden loud
volumes when the TV speaker is
enabled.
MyChoice and ThemeTV
Install MyChoice
You can customise a list of premium
channels for your hotel guests. These
channels are only accessible with an
authorised PIN code.
[Blue mute]: Select [On] to change the
background colour to blue when no
signal is received. The default colour is
black.
1. In Professional setup menu, select
[Digit Timeout]: Set the maximum
time interval between selection of
consecutive numeric buttons on the
remote control.
[Selectable AV]: Select which external
sources are available when
SOURCE is pressed.
[Installation].
2. Select [MyChoice] > [On], then press
OK.
The MyChoice button on the remote
control is activated.
Set up MyChoice
[Watch TV]: Select which external
1. In Professional setup menu, select
[MyChoice setup].
source is displayed when
TV is
pressed on the remote control.
2. Select the list of channels, then press OK.
[Ask for PIN]: Enable PIN to access
MyChoice channels.
[Package 1], [Package 2]: List of
MyChoice and free channels.
[Free Package]: List of all available free
channels accessible to hotel guests.
Change speaker settings
You can set the audio output and volume of
the TV. If independent external speakers are
attached, they will match the audio of the
TV speakers.
1. In the Professional setup menu, select
Watch MyChoice channels
1. Press MyChoice.
2. Enter the PIN code to watch the channels.
[Speaker settings].
2. Select a setting to change, then press OK.
[TV speaker enable]: Enable or disable
TV speakers. Select [Off] to output
audio through headphones or external
speakers.
Install ThemeTV
You can create a maximum of six theme lists
for your hotel guests.
1. In the Professional setup menu, select
[Installation].
2. Select [ThemeTV] > [On], then press
OK.
The
ThemeTV button on the remote
control is activated.
EN
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip: To enable ThemeTV at TV start-up,
select [ThemeTV] > [Startup].
Alarm settings
1. Press
.
2. Select [Guest menu] > [Alarm], then
select one of these options:
Set up ThemeTV
1. In the Professional setup menu, select
[ThemeTV Configuration].
2. Select a channel group to edit.
3. Select [ThemeTV Channel setup].
4. Select the channels to add to your channel
group.
[Alarm status]: Enable or disable the
alarm.
[Alarm time]: Set the time for the
alarm.
[Wakeup volume]: Set the TV volume
when the TV wakes up from standby.
[Wakeup tune]: Select a tune to play
when the TV wakes up from standby.
[Wakeup channel]: Select the channel
to display when the TV wakes up from
standby.
Change guest menu settings
Here are a few settings that hotel guests can
change.
Picture settings
1. Press
.
Multimedia
1. Press
2. Select [Guest menu] > [Picture], then
.
select one of these options:
2. Select [Guest menu] > [Multimedia] to
open the USB content browser and access
multimedia files. This option is only available
if [Enable USB] is enabled in the [Control
settings] menu.
[Picture format]: Change the picture
format.
[Brightness]: Adjust screen brightness.
[Video contrast]: Change the intensity
of the bright areas, keeping dark areas
unchanged.
Mychoice
1. Press
.
[Colour]: Adjust colour saturation of
the picture.
[Sharpness]: Adjust the sharpness of
the picture.
2. Select [Guest menu] > [MyChoice] to
access MyChoice channels. This option is
only available if [MyChoice] is enabled in the
[Installation] menu.
Sound settings
1. Press
Enter the PIN to watch the channels.
.
ThemeTV
2. Select [Guest menu] > [Sound], then
1. Press
.
select one of these options:
2. Select [Guest menu] > [ThemeTV] to
access ThemeTV options. This option is only
available if [ThemeTV] is enabled in the
[Installation] menu.
[Audio language]: Select the preferred
audio language for digital channels.
[Dual I/II]: Select preferred audio
language for analogue channels.
[Mono / stereo]: Select preferred audio
format for analogue channels.
Play games
Feature settings
1. Press
.
What you can do
2. Select [Guest menu] > [Features], then
select one of these options:
On this TV, you can play standard games in
full-screen with optimised picture settings for
games.
[Subtitle mode]: Select the subtitle
mode.
[Subtitle language]: Select the available
subtitle language.
[Sleep timer]: Set the timer.
EN
20
Download from Www.Somanuals.com. All Manuals Search And Download.
What you need
View Text
Select a page
While you watch channels that broadcast
text, you can view the text.
1. Select a channel that broadcasts text, then
press TEXT.
2. Select a page in one of the following ways:
Connect your game console to this TV.
Enter the page number with the
See Connect your TV > Connect
If the TV automatically adds the game
console to the Source menu, it also
applies the game sound preset when
you start playing games (for certain
models).
Numeric buttons.
Press CH + / CH - to view the next or
previous page.
Press the Colour buttons to select a
colour coded item.
Text options
Start gaming
1. While you view text, press OPTIONS.
2. Select an option:
1. Press
SOURCE.
[Freeze page] / [Unfreeze page]:
Freeze or unfreeze the current page.
[Dual screen] / [Full screen]: Enable or
disable dual screen text. Dual screen
displays both the current channel and
the text broadcast on two halves of the
TV screen.
2. Select the game console, then press OK.
3. If needed, load a game disc on the game
console, then select a game to play.
4. Follow the onscreen instructions to start
gaming.
Game settings
Picture setting for games
You can optimise the TV display for gaming
without picture lag.
[T.O.P. overview]: Table Of Pages
(T.O.P.) text broadcasts allow you to
jump from one subject to another
without entering page numbers.
[Enlarge] / [Normal view]: Zoom in on
the page. Press the Navigation buttons
to move around the enlarged view.
[Reveal]: Hide or reveal hidden
information on a page, such as solutions
to riddles or puzzles.
1. Press
.
2. Select [Setup] > [TV settings] >
[Picture], then press OK.
3. Select [Game or computer] > [Game].
Sound preset for games
You can optimise sound effects for gaming.
1. Press OPTIONS.
2. Select [Picture and sound] > [Sound
style] > [Game], then press OK.
The TV is ready for gaming.
[Cycle subpages]: If subpages are
available, each is shown automatically.
[Language]: Switch to a different
language group to correctly display
different character sets.
Note: When your gaming session ends,
switch back to your usual sound setting.
[Text 2.5]: View text with more
colours and better graphics than normal
text. If Text 2.5 is broadcast by a
channel, it is switched on by default.
EN
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Text language
Set locks and timers
For digital TV channels where the
broadcasters provide different text
languages, you can select your preferred
primary and secondary languages.
Clock
You can display a clock on the TV. The clock
displays the time that is broadcast by your
TV service operator.
1. Press
.
2. Select [Setup] > [Channel settings].
3. Select [Languages] > [Primary Text] or
[Secondary Text].
Display the TV clock
1. While you watch TV, press CLOCK.
The clock is displayed on the top right-hand
corner of the TV screen.
4. Select a language, then press OK.
Subpages
Change the clock mode
You can change the clock mode to
automatic or manual. By default, it is set to
automatic mode, which automatically
synchronises it to Coordinated Universal
Time (UTC). If your TV cannot receive UTC
transmissions, change the clock mode to
[Manual].
If the text page contains several subpages,
you can view each subpage in succession.
These subpages are shown on a bar next to
the main page number.
Press or to select them.
Search
1. While you watch TV, press
.
You can search for a word or number that
exists on the current text page.
2. Select [Setup] > [TV settings] > [General
settings].
1. While you are viewing text, press OK to
highlight the first word or number.
2. Press the Navigation buttons to skip to
3. Select [Clock] > [Auto clock mode].
4. Select [Automatic], [Manual] or [Country
dependent], then press OK.
the word or number to search.
Change the time zone
3. Press OK to begin the search.
4. To exit the search, press until no word
or number is highlighted.
In countries with clock transmission data, you
can change the time zone if [Auto clock
mode] > [Automatic] or [Country
dependent] is selected.
Digital text
1. In the [Clock] menu, select [Time zone].
2. Select your time zone, then press OK.
If a digital TV channel's broadcaster offers
dedicated digital text or interactive services,
you can view digital text. Channels such as
BBC1 may have digital text with more
interactive features.
Set daylight saving time
In countries with clock transmission data, you
can enable or disable daylight saving time if
[Auto clock mode] > [Automatic] or
[Country dependent] is selected.
Note: Digital text services are blocked when
subtitles are broadcast and switched on. See
Change your TV settings > Language
settings > Subtitles on digital channels
1. In the [Clock] menu, select [Daylight
saving].
2. Select [Standard time] or [Daylight saving
time], then press OK.
(Page 28).
When in digital text:
Set the clock manually
Press the Navigation buttons to select
You can set the date and time manually.
Before you start, set the clock mode to
[Manual].
or highlight items.
Press the Colour buttons to select an
option, then press OK to confirm or
activate.
EN
22
Download from Www.Somanuals.com. All Manuals Search And Download.
1. In the [Clock] menu, select [Date] or
[Time], then press OK.
2. Set the time or date with the Navigation
buttons.
Parental rating
You can set your TV to display only
programmes with age ratings lower than
your child's age. This restriction only applies
to digital channels from broadcasters that
rate their programmes according to age.
3. Select [Done], then press OK.
Sleep timer
1. Press
.
You can switch the TV to standby after a
specified time. During the countdown to the
specified time, you can switch off your TV
earlier or reset the sleep timer.
2. Select [Setup] > [Channel settings].
3. Select [Child lock] > [Parental rating].
You are prompted to enter the child lock
code.
1. Press
.
4. Enter the child lock code with the
Numeric buttons.
5. Select an age rating, then press OK.
2. Select [Setup] > [TV settings] > [General
settings] > [Sleep timer].
3. Select the sleep timer duration.
The sleep timer can be set up for to 180
minutes. To switch off the sleep timer, set it
to zero minutes.
All programmes above the selected age
rating are blocked.
For information on child lock codes, see Use
more of your TV > Set locks and timers >
4. Press OK to activate the sleeptimer. After
the specified time, the TV switches to
standby.
Child lock
To protect children from unsuitable TV
programmes, you can lock the TV or block
age rated programmes.
Set or change the child lock code
1. Press
.
2. Select [Setup] > [Channel settings] >
[Child lock].
3. Select [Set code] or [Change code].
4. Enter the code with the Numeric
buttons.
Tip: If you access the channels from the
channel list, you are prompted to enter your
lock code. If you forget your code, enter
‘8888’ to override any existing codes.
Lock or unlock channels
1. In the child lock menu, select [Channel
lock].
2. Enter the child lock code with the
Numeric buttons.
3. Select the channels to lock or unlock.
Restart the TV to activate the lock.
Note:
If you access the channels from the channel
list, you are prompted to enter your lock
code.
EN
23
Download from Www.Somanuals.com. All Manuals Search And Download.
superior sharpness, especially on lines
and contours in the picture
4 Change your TV
settings
- [Dynamic contrast]: Dynamically
enhance the details in the dark, medium and
light areas of the picture.
- [Dynamic backlight]: Select a
Picture and sound
backlight level to optimise dynamic power
consumption and picture contrast.
- [Colour enhancement]:
Dynamically enhance the vividness and
details of colours.
Settings assistant
You can select picture and sound settings
with the help of the settings assistant, which
demonstrates the effect of your chosen
setting immediately.
[Advanced]: Access advanced settings
such as gamma, tint settings and video
contrast settings.
- [Gamma]: Adjust the non-linear
setting for picture luminance and
contrast.
- [Tint]: Change the colour
balance.
1. While you watch TV, press
2. Select [Setup] > [Quick picture and
sound settings], then press OK.
3. Select [Continue], then press OK.
4. Follow the onscreen instructions to
choose your preferred settings.
.
- [Custom tint]: Customise colour
balance setting. Only available if [Tint] >
[Custom] is selected.
More picture settings
You can change the settings in the Picture
menu.
- [Video contrast]: Adjust video
contrast.
- [Brightness]: Adjust screen
1. Press
.
brightness.
2. Select [Setup] > [TV settings] >
[Picture], then press OK.
- [Hue]: Compensate colour
variations in NTSC transmissions.
3. Select a setting to change, then press OK.
[Game or computer]: When viewing
content from a connected game
[Picture style]: Select a predefined
picture setting.
[Restore style]: Restores the previously
console, select [Game] to apply game
settings. When a computer is
connected through HDMI, select
[Computer]. Make sure that [Format
and edges] > [Picture format] >
[Unscaled] is selected to view
maximum detail.
[Format and edges]: Access advanced
settings to control the display format of
the picture.
- [Picture format]: Change the
picture format.
- [Screen edges]: Change the
picture size.
selected picture settings.
[Backlight contrast]: Adjust the
brightness of the display backlight.
[Colour]: Adjust the colour saturation
of the picture.
[Sharpness]: Adjust the sharpness of
the picture.
[Noise reduction]: Select the amount
of noise reduction for the picture.
[MPEG artifact reduction]: Smoothen
transitions and haziness in the digital
picture.
- [Picture shift]: If available, move
the position of the picture.
[Digital Crystal Clear]: Fine-tune each
pixel to match the surrounding pixels
and produce a brilliant, high-definition
image.
- [Advanced sharpness]: Enable
EN
24
Download from Www.Somanuals.com. All Manuals Search And Download.
output from the ARC-compliant device
connected to the HDMI 1 connector.
More sound settings
You can change the settings in the Sound
menu.
- [Audio out delay]: Automatically
sync the image on the TV to the audio from
a connected home theatre. You do not need
to use this setting when connecting the TV
to a Philips home theatre.
- [Audio out offset]: Adjust the
setting for audio output delay. Available if
[Audio out delay] is switched on.
1. Press
.
2. Select [Setup] > [TV settings] > [Sound],
then press OK.
3. Select a setting to change, then press OK.
[Sound style]: Access predefined sound
settings.
[Restore style]: Restore the last
selected predefined sound setting.
[Bass]: Adjust the bass level of the
speaker and headphones.
[Treble]: Adjust the treble level of the
speaker and headphones.
[Surround mode]: Select a surround
Audio format
Digital channels
If a digital TV channel broadcaster streams
audio in multiple formats, you can select an
audio format.
1. Press
.
sound mode to enhance your audio
experience.
2. Select [Setup] > [Channel settings] >
[Languages] > [Preferred audio format].
3. Select an option, then press OK.
[Auto incredible surround 3D]: Select
a surround sound mode to enhance
your audio experience in 3D mode. For
certain models.
[Standard]: Receive standard audio
format (MPEG).
[Advanced]: Receive advanced audio
formats, if available (AAC, Dolby Digital
or Dolby Digital Plus).
[Headphone volume]: Adjust
headphone volume.
[Advanced]: Access advanced settings
to enhance your audio experience.
- [Auto volume levelling]:Enable
the reduction of sudden volume
changes, for example, when switching
channels.
Analogue channels
If an analogue TV channel broadcaster
streams stereo audio in multiple formats, you
can select an audio format.
1. Press
.
- [TV speakers]: Select the
2. Select [Setup] > [Channel settings] >
[Mono/Stereo].
preferred speakers to stream audio
from the TV. See Connect your TV >
Set up EasyLink devices > Select
3. Select a setting, then press OK.
Reset picture and sound
You can restore the default picture and
sound settings, while the channel installation
settings remain the same.
- [Clear Sound]*: Enhance sound
quality.
- [Audio Out format]: Select the
type of audio output through the digital
audio output connector. Choose between
[Multichannel] and [Stereo].
1. While you watch TV, press
.
2. Select [Setup] > [TV settings] > [General
settings] > [Factory settings], then press
OK.
* Available on certain models only.
- [Audio Out levelling]: Set the
output level for stereo audio. Select [Less]
for a certain amount of loss in intensity or
signal strength. Select [More] for no loss in
intensity or signal strength.
3. Select [OK], then press OK.
All TV settings (except for channel settings)
are reset to the default factory settings.
- [HDMI 1 - ARC]: Enable audio
EN
25
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Select the system for your country or
region, then press OK.
Channels
Step 2: Search and store new TV channels
Automatic installation
When the TV was switched on for the first
time, a full installation of channels was
performed.
1. While you watch TV, press
2. Select [Setup] > [Channel settings] >
[Channel installation].
3. Select [Analogue: Manual installation] >
[Search channel], then press OK.
.
To change your language, country and
reinstall all available TV channels, you can run
this full installation again.
Start installation
Note: If you are prompted to enter a code,
4. Find the channel:
If you know the channel frequency,
enter it with the Navigation buttons or
Numeric buttons.
If you do not know the channel
frequency, search for the next
frequency that has a strong signal.
Select [Search], then press OK.
enter '8888'.
1. Press
.
2. Select [Setup] > [Search for channels] >
[Reinstall channels], then press OK.
3. Select your country, then press OK.
5. After you have found the correct channel,
select [Done], then press OK.
6. Select [Store as new channel], then press
OK to store the new TV channel.
4. Select your network, then press OK:
[Antenna (DVB-T)]: Access free-to-air
antenna transmissions.
Note: If the reception is poor, reposition
your antenna and repeat the procedure.
[Cable (DVB-C)]: Access cable
transmissions.
5. Follow the onscreen instructions to select
other options, if any.
The start menu for channel search is
displayed.
6. Select [Start], then press OK.
Install digital channels
If you know the channel frequency of the
channels you want to install, you can search
and store digital channels one by one. For
best results, contact the service provider.
7. Once the channel search is complete,
select [Finish], then press OK.
1. Press
.
2. Select [Setup] > [Channel settings] >
Tip: Press LIST to see the channel list.
[Channel installation].
Note: When digital TV channels are found,
the list of installed channels may display
empty channel numbers. You can rename or
reorder these channels.
3. Select [Digital: Reception test] > [Search
channel], then press OK.
4. Press the Numeric buttons to enter the
channel frequency.
5. Select [Search], then press OK.
6. When the channel is found, select [Store],
then press OK.
Install analogue channels
You can search and store analogue TV
channels one by one.
Step 1: Select your system
Note: Skip this step if your system settings
are correct.
Fine-tune analogue channels
If the reception of an analogue TV channel is
poor, you can fine-tune the TV channel.
1. While you watch TV, press
.
1. Press
.
2. Select [Setup] > [Channel settings] >
[Channel installation].
2. Select [Setup] > [Channel settings] >
[Channel installation].
3. Select [Analogue: Manual installation] >
[System], then press OK.
3. Select [Analogue: Manual installation] >
[Fine tune], then press OK.
4. Press or to fine-tune the channel.
EN
26
Download from Www.Somanuals.com. All Manuals Search And Download.
5. When you have selected the correct
channel frequency, select [Done], then press
OK.
You can copy channel lists from one Philips
TV to another through a USB storage
device. You do not need to search for
channels or install them again on the second
TV. The channel list file is small enough to fit
on any USB storage device.
6. Select an option, then press OK.
[Store current channel]: Store the
channel under the current channel
number.
What you need
Two Philips TVs that have these properties:
[Store as new channel]: Store the
channel under a new channel number.
The same country setting
The same year range
The same DVB type, as indicated by
the suffix (H, K, T, D/00) in the model
name
Update channel list
When the TV was switched on for the first
time, a full installation of channels was
performed. By default, when there are
changes to these channel lists, the TV
updates them automatically. You can also
switch off the automatic update or manually
update the channels.
The same hardware type, as indicated
by the sticker on the back of the TV.
For example: TPM10.1E LA.
Compatible software versions
Note: If you are prompted to enter a code,
enter '8888'.
Note: If you are prompted to enter a code,
enter '8888'.
Step 1: Check the country setting
1. Switch on the first TV (with the channels
that you want to copy to the second TV).
Automatic update
To add or remove digital channels
automatically, leave the TV in standby mode.
The TV updates channels and stores new
channels everyday. Empty channels are
removed from the channel list.
2. Press
.
3. Select [Setup] > [Search for channels] >
[Reinstall channels], then press OK.
The country menu is displayed.
Switch off the channel update message
If a channel update is performed, a message
is displayed at startup. You can switch off this
message.
4. Make a note of the current setting.
5. Press
.
6. Press [Cancel] to exit.
Step 2: Copy channel list to USB
1. Connect a USB storage device to the first
TV (with the channels installed on it).
1. Press
.
2. Select [Setup] > [Channel settings].
3. Select [Channel installation] > [Channel
update message].
2. Press
.
3. Select [Setup] > [Channel settings].
4. Select [Off], then press OK.
4. Select [Channel installation] > [Copy
channel list] > [Copy to USB], then press
OK.
The channel list is copied to the USB storage
device.
Switch off automatic updates
In the [Channel installation] menu, select
[Automatic channel update] > [Off].
Update channels manually
1. Press
.
5. Disconnect the USB storage device.
2. Select [Setup] > [Search for channels] >
[Update channels], then press OK.
3. Follow the onscreen instructions to
update the channels.
Step 3: Copy channels to a TV with no
channels installed
1. Switch on the second TV, on which you
want to copy the channel list.
Initial installation starts.
Copy channels
ATTENTION: This feature is intended for
dealers and service personnel.
2. Follow the onscreen instructions and
select the same country as the TV whose
channel list you want to copy.
EN
27
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Skip the search for channels.
4. Connect the USB storage device.
Audio language
If the TV channel broadcasts multiple or dual
audio languages, you can select your
preferred audio language.
5. Press
.
6. Select [Setup] > [Channel settings].
7. Select [Channel installation] > [Copy
channel list] > [Copy to TV], then press
OK.
1. While you watch TV, press OPTIONS.
2. For digital channels, select [Audio
language]. For analogue channels, select
[Dual I-II]. Press OK to confirm your
selection.
The channel list is copied to the TV storage
device.
8. Disconnect the USB storage device.
3. Select from the available languages, then
press OK.
Step 3: Copy channels to a TV with pre-
installed channels
You can set your preferred primary and
secondary audio languages to hear when
available.
1. Switch on the second TV, on which you
want to copy the channel list.
2. Press
.
3. Select [Setup] > [Search for channels] >
[Reinstall channels], then press OK.
The country menu is displayed.
1. While you watch TV, press
.
2. Select [Setup] > [Channel settings] >
[Languages].
3. Select [Primary audio language] or
[Secondary audio language] and select from
4. Make sure that the country setting is the
same as for the first TV.
5. Press
.
the available languages.
4. Press OK to confirm.
6. Press [Cancel] to exit.
7. If the country setting is different, reinstall
the second TV to match the country setting
of the first TV. See Change your TV settings
> Reset all.
8. Connect the USB storage device to the
second TV.
Subtitles on analogue channels
1. While you watch an analogue TV channel,
press TEXT.
2. Enter the three-digit page number of the
subtitles page, which is usually '888'.
If available, subtitles are switched on.
9. Press
.
10. Select [Setup] > [Channel settings].
11. Select [Channel installation] > [Copy
channel list] > [Copy to TV], then press
OK.
The channel list is copied to the second TV.
12. Disconnect the USB storage device.
Subtitles on digital channels
1. While you watch a digital TV channel,
press OPTIONS.
2. Select [Subtitles], then press OK.
3. Select [Subtitles off], [Subtitles on] or
[Automatic], then press OK.
Language settings
Subtitle language
When available, you can change the subtitle
language for digital channels.
Menu language
1. While you watch TV, press
.
1. While you watch TV, press OPTIONS.
2. Select [Subtitle language], then select
from the available languages and press OK.
The subtitle language is changed for the
specific channel.
2. Select [Setup] > [TV settings] > [General
settings] > [Menu language].
3. Select a menu language from the list, then
press OK.
You can set your preferred primary and
secondary subtitle languages to display when
available.
EN
28
Download from Www.Somanuals.com. All Manuals Search And Download.
1. While you watch TV, press
2. Select [Setup] > [Channel settings] >
[Languages].
3. Select [Primary subtitle language] or
[Secondary subtitle language] and select
from the available languages.
4. Press OK to confirm.
.
Visually impaired access
To make sure that a hearing-impaired audio
language is available, press OPTIONS,
then select [Audio language]. Languages that
support visually impaired audio are indicated
with an eye-shaped icon.
Select speakers or headphones
You can choose to hear the visually impaired
audio through the TV speakers, headphones
or both.
Universal access settings
1. While you watch TV, press OPTIONS.
2. Select [Universal access] > [Visually
impaired].
Switch on
Some digital TV broadcasters provide special
audio and subtitle features for people who
are hearing or visually impaired. You can
switch these features on or off.
3. Select a setting, then press OK.
[Speakers]: Hear visually impaired
audio from speakers only.
[Headphones]: Hear visually impaired
1. Press
.
2. Select [Setup] > [TV settings] > [General
settings].
audio from headphones only.
[Speakers + headphones]: Hear visually
impaired audio from speakers as well as
headphones.
3. Select [Universal access] > [On] or [Off],
then press OK.
[Off]: Switch off visually impaired audio.
Set audio feedback
When you press a button on the remote
control or TV, you can set the TV to play a
beep.
Note: If the EasyLink remote control is
switched on, you cannot select the Green
button. To switch off EasyLink, see Connect
your TV > Set up EasyLink devices > What
1. While you watch TV, press OPTIONS.
2. Select [Universal access] > [Key beep] >
[On], then press OK.
Change volume for visually impaired audio
1. While you watch TV, press OPTIONS.
2. Select [Universal access] > [Mixed
volume].
Hearing impaired access
3. Press the Navigation buttons to change
the volume, then press OK.
To make sure that a hearing-impaired audio
language is available, press OPTIONS,
then select [Audio language]. Languages that
support hearing-impaired audio are indicated
with an ear-shaped icon.
Audio effects
1. Press
.
2. Select [Setup] > [Channel settings].
3. Select [Languages] > [Visually impaired]
or [Audio effects].
Switch on hearing-impaired audio and
subtitles
1. While you watch TV, press OPTIONS.
2. Select [Universal access] > [Hearing
impaired].
4. Select a setting, then press OK.
[On]: Enable audio effects in the visually
impaired audio.
3. Select a setting, then press OK.
[Off]: Disable audio effects in the
[Off]: Switch off hearing impaired
features.
visually impaired audio.
[On]: Switch on hearing impaired audio
and subtitles.
EN
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Type of speech
1. Press
.
2. Select [Setup] > [Channel settings].
3. Select [Languages] > [Visually impaired]
or [Speech].
4. Select a setting, then press OK.
[Descriptive]: Hear descriptive speech
in the visually impaired audio.
[Subtitles]: Hear subtitles in the visually
impaired audio.
Other settings
TV demo
You can watch a demo to find out more
about the features on this TV.
1. While you watch TV, press
.
2. Select [Setup] > [Watch demos], then
press OK.
3. Select a demo, then press OK.
Home mode
Some TV settings may not be available in
Shop mode. To make sure that the correct
TV settings are applied, set the TV to Home
mode.
1. While you watch TV, press
.
2. Select [Setup], then press OK.
3. Select [TV settings] > [General settings]
> [Location].
4. Select [Home] or [Shop], then press OK.
5. Restart the TV.
Reset all
You can reset all picture and sound settings
and reinstall all TV channels on your TV.
1. Press
.
2. Select [Setup] > [TV settings] > [General
settings] > [Reinstall TV], then press OK.
3. Select [Yes], then press OK.
4. Follow the onscreen instructions.
EN
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Y Pb Pr
5 Connect your
TV
Component video (Y Pb Pr) only transmits
video. For sound, also connect to Audio
Left/Right.
The Y Pb Pr connection can handle
high-definition (HD) TV signals.
Match the Y Pb Pr connector colours
to the cable plugs.
About cables
Cable quality
Before you connect devices to the TV, check
the available connectors on the device.
Connect the device to the TV with the
highest quality connection available. Good
quality connectors transfer picture and
sound better.
The connections shown in this user manual
are recommendations only. Other solutions
are possible. For more examples, visit
SCART
Tip: If your device has only composite or
RCA connectors, use a composite (CVBS)
cable to connect the device to the CVBS/Y
connector on the TV.
A SCART connection combines video and
audio signals.
SCART connectors can handle RGB video
signals but cannot handle high-definition
(HD) TV signals.
HDMI
An HDMI connection has the best picture
and sound quality.
An HDMI cable combines video and
audio signals. Connect HDMI for high-
definition (HD) TV signals and to switch
on EasyLink.
An HDMI Audio Return Channel
(ARC) connector allows output of TV
audio to an HDMI ARC compliant
device.
Connect HDMI cables shorter than 5
meters/16.4 feet.
EN
31
Download from Www.Somanuals.com. All Manuals Search And Download.
VGA*
You can connect VGA to display PC content
on the TV. VGA only transmits video.
* Available on 22, 24, and 26-inch models
only.
Connect antenna
Connect the antenna to the TV.
Connect devices
Blu-ray or DVD disc player
Connect the disc player to the TV with an HDMI cable.
EN
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the disc player to the TV with a component video cable (Y Pb Pr) and an audio L/R cable.
TV receiver
Connect the digital TV receiver with an antenna cable to the TV.
Connect the satellite or digital TV receiver to the TV with an HDMI cable.
EN
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the digital TV receiver to the TV with a component video cable (Y Pb Pr) and an audio
L/R cable.
Connect the digital TV receiver to the TV with a SCART cable.
Video recorder
Connect the recorder to the TV with an antenna cable.
EN
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the recorder to the TV with an HDMI cable.
Connect the recorder to the TV with a component video cable (Y Pb Pr) and an audio L/R cable.
Connect the recorder to the TV with a SCART cable.
EN
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Game console
Connect the game console to the TV with an HDMI cable.
Connect the game console to the TV with a component video cable (Y Pb Pr) and an audio L/R
cable.
Home theatre
Connect an HDMI-ARC compliant home theatre to the TV with an HDMI cable.
EN
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the home theatre to the TV with an HDMI cable and a coaxial audio cable.
Connect the home theatre to the TV with a component video cable (Y Pb Pr) and an audio L/R
cable.
Connect the home theatre to the TV with a SCART cable.
EN
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital camera
Connect the digital camera to the TV with a USB cable.
Digital camcorder
Connect the digital camcorder to the TV with an HDMI cable.
Connect the digital camcorder to the TV with a component video cable (Y Pb Pr) and an audio L/R
cable.
EN
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect more devices
USB storage device
Connect the USB hard drive to the TV with
a USB cable.
Connect the USB flash drive with a USB
cable to the TV.
Computer
Connect the computer to the TV with an HDMI cable.
EN
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the computer to the TV with a DVI-HDMI cable.
Connect the computer to the TV with a VGA cable*.
* Available on 22, 24, and 26-inch models only.
Update the source list
If you add or remove a device, update the
source list.
Watch connected devices
Select a device
Before you can watch a device, connect the
device to the TV. See Connect your TV >
1. Press
2. Press OPTIONS.
3. Select [Scan connections], then press OK.
4. Follow the onscreen instructions.
SOURCE.
Select a device with SOURCE
Change device settings
Change the device type
1. Press
SOURCE.
2. Select a device, then press OK.
You can change the device type to easily
access it from the Source menu.
Select a device from Home menu
1. Press
.
1. Press
SOURCE.
2. Select [Source], then press OK.
2. Select the device, then press [Device
type].
3. Select a device, then press OK.
3. Select a suitable device type, then press
OK.
EN
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Rename a device
You can rename a device after it is
connected to the TV.
EasyLink remote control
You can control multiple HDMI-CEC
compliant devices with your TV remote
control.
1. Press
SOURCE.
System audio control
2. Select the connector, then press
[Rename].
If you connect an HDMI-CEC compliant
device that includes speakers through the
HDMI ARC connector, you can choose to
hear the TV audio from those speakers
instead of the TV speakers.
3. Use the on-screen keypad to enter a new
name.
4. When complete, select [Done], then
press OK.
Retain picture quality
Reset device settings
If your TV picture quality is affected by the
picture-processing features of other devices,
you can switch on Pixel Plus Link to retain
picture quality.
You can reset the type and name of the
device to default settings.
1. In the [Source] menu, select the device
and press OPTIONS.
Maximise display for subtitled video
Some video subtitles can create a separate
subtitle bar under the video, which limits the
video display area. To maximise the video
display area, you can switch on auto subtitle
shift and display the subtitles on the video
image.
2. Select [Original name and icon], then
press OK.
Set up EasyLink devices
What you can do
What you need
You can get the most out of your HDMI-
CEC-compliant devices with Philips EasyLink
enhanced control features. Connect your
HDMI-CEC compliant devices through
HDMI to your TV and control them at the
same time with your TV remote control.
Connect an HDMI-CEC compliant
device to the TV. You can connect
more than one HDMI-CEC device. See
Connect your TV > Connect devices
(Page 32).
Configure each HDMI-CEC compliant
device properly.
Switch on EasyLink.
Note: Other brands describe HDMI-CEC
functionality differently. Some examples are
Anynet (Samsung), Aquos Link (Sharp) or
BRAVIA Sync (Sony). Not all brands are fully
compatible with Philips EasyLink.
Switch on EasyLink
1. Press
.
2. Select [Setup] > [TV settings] > [General
settings] > [EasyLink].
After you have switched on Philips EasyLink,
the following features are available:
3. Select [EasyLink] > [On], then press OK.
One-touch play
When you play an HDMI-CEC compliant
device, the TV switches on from standby and
switches to the correct source.
Control devices
If you connect multiple HDMI-CEC devices
that support this setting, you can control all
such devices through the TV remote control.
One-touch standby
When you press on the TV remote
control, the TV and all HDMI-CEC
compliant devices switch to standby mode.
Auto switch off inactive devices
If a HDMI-CEC compliant device has been
inactive for some time, it switches to standby
mode.
Note: This is an advanced setting. Devices
that do not support this setting cannot
respond to the TV remote control.
EN
41
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Press
.
3. Select one of the following, then press
2. Select [Setup] > [TV settings] > [General
settings] > [EasyLink] > [EasyLink remote
control].
OK.
[On]: Hear the TV audio through the
connected HDMI-ARC compliant
device.
3. Select [On] or [Off], then press OK.
[Off]: Hear the TV audio through the
TV speakers, or through a device
connected through the digital audio out
connector.
Tips:
To switch back to TV control, press
,
then select [Watch TV].
To control another device, press
,
Note: Make sure that all HDMI-CEC settings
are properly set up on the connected device.
Set up TV speakers
then select the device from the Home
menu.
EasyLink buttons
1. Press
.
You can control HDMI-CEC compliant
2. Select [Setup] > [TV settings] > [Sound]
> [Advanced] > [TV speakers].
devices with the following buttons on the TV
remote control:
: Switch the TV and the connected
device on or to standby.
Numeric buttons: Select a title, chapter
3. Select an option, then press OK:
[Off]: Switch off TV speakers.
[On]: Switch on TV speakers.
[EasyLink]: Switch off TV speakers and
stream TV audio to a connected
HDMI-CEC audio device.
or track.
OK: Start, pause or resume play on the
connected device, activate a selection,
or access the device menu.
[EasyLink autostart]: When a HDMI-
CEC audio device is connected,
automatically switch off TV speakers
and stream TV audio to the device.
: Display the TV Home menu.
Switch off connecting devices
You can also set the TV to switch off the
connecting HDMI-CEC compliant devices if
they are not the active source. The TV
switches the connecting device to standby
after 10 minutes of inactivity.
Change TV audio streaming
You can switch audio between TV speakers
and a connected amplifier at any time.
1. Press OPTIONS.
2. Select [Picture and sound] > [Speakers].
1. Press
.
2. Select [Setup] > [TV settings] > [General
settings] > [EasyLink].
3. Select one of the following, then press
OK.
3. Select [Auto switch off devices] > [On],
then press OK.
[TV]: On by default.
Stream TV audio through TV and the
connected HDMI-CEC audio device
until the connected device switches to
system audio control. TV audio is then
streamed through the connected
device.
Select speaker output
If a connected device is HDMI Audio Return
Channel (HDMI ARC) compliant, you can
output TV audio through an HDMI cable.
Additional audio cables are not required.
Make sure you connect the device to the
HDMI ARC connector on the TV. See
Connect your TV > About cables > HDMI
[Amplifier]: Stream audio through the
connected HDMI-CEC device. If system
audio mode is not enabled on the
device, audio continues to stream from
the TV speakers. If [EasyLink autostart]
was selected, the TV prompts the
connected device to switch to system
audio mode.
(Page 31).
Switch on HDMI ARC
1. Press
2. Select [Setup] > [TV settings] > [Sound]
> [Advanced] > [HDMI 1 - ARC].
.
EN
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Retain picture quality
What you need
Caution: To protect the CAM from damage,
insert the CAM as instructed.
If your TV picture quality is affected by the
picture-processing features of other devices,
you can switch on Pixel Plus Link.
Note: Refer to the documentation from
your service operator on how to insert a
smart card into the Conditional Access
Module.
Switch on Pixel Plus Link
1. Press
.
2. Select [Setup] > [TV settings] > [General
settings] > [EasyLink].
3. Select [Pixel Plus Link] > [On], then press
OK.
Maximise video display
Some subtitles create a separate subtitle bar
under the video that limits the video display
area. To maximise the video display area,
you can switch on auto subtitle shift. The
subtitles are then displayed over the video
image.
1. Switch off the TV.
Switch on auto subtitle shift
2. Follow the directions printed on the CAM
to insert the CAM into the Common
Interface slot at the side of the TV.
Push the CAM in as far as it will go.
3. Switch on the TV, then wait for the CAM
to be activated. This takes a few minutes.
To maintain access to encrypted digital TV
channels, leave the CAM in the slot.
1. Press
.
2. Select [Setup] > [TV settings] > [General
settings] > [EasyLink].
3. Select [Auto subtitle shift] > [On], then
press OK.
Connect a CAM
(Conditional Access
Module)
Access CAM services
1. After you insert and activate the CAM,
press OPTIONS.
2. Select [Common interface], then press
OK.
What you can do
3. Select the CAM provider, then press OK.
You can watch scrambled digital TV channels
with a Conditional Access Module (CAM).
Once you have inserted the CAM and paid
the subscription fees, you can watch the
programmes.
This TV supports CI (Common Interface) as
well as CI+. CI+ supports premium HD
digital programmes with a high level of copy
protection.
Note: The applications, functions, content
and onscreen messages depend on the CAM
service provider.
EN
43
Download from Www.Somanuals.com. All Manuals Search And Download.
blinking reoccurs, contact Philips Consumer
Care.
6 Troubleshooting
The TV audio is in the wrong language:
If you select audio language via OPTIONS,
the TV resets to the default language when
you change channels or switch off the TV.
To retain the selected language, change your
audio language by pressing , then selecting
[Setup] > [Channel settings] > [Languages]
> [Primary audio language] or [Secondary
audio language].
General issues
The TV does not switch on:
Disconnect the power cable from the
power outlet. Wait for one minute
then reconnect it.
Make sure that the power cable is
securely connected.
The TV or Smart TV menu is in the wrong
language:
Change the menu to your preferred
language.
When you are turning the TV on, off or to
standby, you hear a creaking sound from
the TV chassis:
For more information, see Change your TV
settings > Language settings > Menu
No action is required. The creaking sound is
due to the normal expansion and
contraction of the TV as it cools and warms
up. This does not affect performance.
You forgot the 4-digit code to unlock the
channel blocking feature (child lock):
Enter ‘8888’.
You want to upgrade your TV software:
download the latest software package for
your TV. Software installation instructions
and release notes indicating what's been
updated are also available at the site. Full
instructions on how to upgrade your TV
software are also available at Change your
TV settings > Update software (Page Error!
The TV does not respond to remote
control or TV controls when switched on:
The TV requires some time to start up.
During this time, the TV does not respond
to the remote control or TV controls. This is
normal behaviour.
If the TV continues to be unresponsive to
the remote control, view the remote control
sensor through a digital camera – if you
press any button on the remote control and
notice red flickering at the sensor, the
remote control is working but the TV may
need to be checked by Philips Consumer
Care. This troubleshooting procedure is not
applicable to remote controls that are paired
wirelessly with the TV.
Bookmark not defined.).
Channel issues
You want to install TV channels:
When the TV is in standby, a start-up
splash screen is displayed, then the TV
returns to standby mode:
This is normal behaviour. When the TV is
disconnected and reconnected to the power
supply, the startup screen is displayed at the
next startup.
To switch on the TV from standby, press
on the remote control or press any key on
the TV.
See Change your TV settings > Automatic
installing analogue or digital channels.
No digital channels were found during the
installation:
See the technical specifications to make
sure that your TV supports DVB-T or
DVB-C in your country.
Make sure that all cables are properly
connected and that the correct
network is selected.
The standby light on the TV blinks red:
Disconnect the power cable from the power
outlet. Wait until the TV cools down before
you reconnect the power cable. If the
EN
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Previously installed channels do not appear
in the channel list:
The picture does not fit the screen; it is
too big or too small:
Make sure that the correct channel list is
selected.
Change to a different picture format.
The picture format keeps changing with
different channels:
You want to rearrange or reorder the
channel list:
Instead of the picture format [Auto zoom],
After channels have been installed, they
appear in the channel list. For information
about managing channel lists, including
rearranging channels, see Watch TV >
select a different picture format.
The picture position is incorrect:
Picture signals from some devices may not fit
the screen correctly. Check the signal output
of the device.
The picture from broadcasts is scrambled:
You may need a Conditional Access Module
to access content. Check with your service
operator.
Picture issues
The TV is on, but there is no picture or the
picture is distorted:
An "e-sticker" banner displaying
information appears on the TV display:
The TV is in [Shop] mode. To remove the
e-sticker, set the TV to [Home] mode, then
restart the TV. See Change your TV settings
Make sure that the antenna is properly
connected to the TV.
Make sure that the correct device is
selected as the display source.
Make sure that the external device or
source is properly connected.
The computer display on the TV is not
stable:
There is sound but no picture:
Make sure that the picture settings are set
correctly.
There is poor TV reception from an
antenna connection:
Make sure that your PC uses the
supported resolution and refresh rate.
See Specifications > Display
Change the TV picture format to
[Unscaled].
Make sure that the antenna is properly
connected to the TV.
Loud speakers, unearthed audio
devices, neon lights, high buildings and
other large objects can influence
reception quality. If possible, try to
improve the reception quality by
changing the antenna direction or
moving devices away from the TV.
If reception on only one channel is
poor, fine-tune this channel.
Sound issues
There is a picture but sound quality is
poor:
If no audio signal is detected, the TV
automatically switches the audio output off
— this does not indicate malfunction.
Make sure that all cables are properly
connected.
Make sure that the volume is not
muted or set to zero.
Make sure that the TV speaker setting
is selected. Press OPTIONS, select
[Picture and sound] > [Speakers], then
select [TV].
There is poor picture quality from
connected devices:
Make sure that the devices are
connected properly.
Make sure that the picture settings are
set correctly.
The TV did not save your picture settings:
Make sure that the TV location is set to
Home. You can change and save settings in
Make sure that the TV audio output is
connected to the audio input on the
this mode.
EN
45
Download from Www.Somanuals.com. All Manuals Search And Download.
HDMI-CEC enabled or EasyLink
compliant home theatre device. Sound
should be heard from the home theatre
speakers.
Some devices may require you to
manually enable HDMI audio output. If
HDMI audio is already enabled, but you
still do not hear audio, try changing the
digital audio format of the device to
PCM (Pulse Code Modulation). Refer
to the documentation accompanying
your device for instructions.
USB device content is not displayed:
Make sure that the USB storage device
is set to Mass Storage Class compliant,
as described in the storage device's
documentation.
Make sure that the USB storage device
is compatible with the TV.
Make sure that the audio and picture
file formats are supported by the TV.
Audio and picture files on your USB
storage device do not play or display
smoothly:
The transfer performance of the USB
storage device may limit the data transfer
rate to the TV which causes poor playback.
There is a picture but the sound quality is
poor:
Make sure that the sound settings are
correctly set.
Contact Philips
Connection issues
Warning: Do not attempt to repair the TV
yourself. This may cause severe injury,
irreparable damage to your TV or void
your warranty.
There are problems with HDMI devices:
Note that HDCP (High-bandwidth
Digital Content Protection) support can
delay the time taken for a TV to display
content from an HDMI device.
If the TV does not recognise the HDMI
device and no picture is displayed,
switch the source from one device to
another and back again.
If there are intermittent sound
disruptions, make sure that output
settings from the HDMI device are
correct.
If you use an HDMI-to-DVI adapter or
HDMI to DVI cable, make sure that an
additional audio cable is connected to
AUDIO L/R or AUDIO IN (mini-jack
only).
If are not able to resolve your problem, refer
to the frequently asked questions (FAQs) for
can also consult and contribute to the Philips
TV community at
If you wish to speak to or email a Philips
representative, contact the Philips Consumer
Care in your country. You can find the
contact details in the leaflet accompanying
Note your TV model and serial number
before you contact Philips. These numbers
are printed on the back of the TV and on
the packaging.
You cannot use EasyLink features:
Make sure that your HDMI devices are
HDMI-CEC compatible. EasyLink features
only work with devices that are HDMI-CEC
compatible.
If an HDMI-CEC compliant audio device is
connected to the TV and the TV does not
display any mute or volume icon when the
volume is muted, increased or decreased:
When a HDMI-CEC audio device is
connected this behaviour is normal.
EN
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture enhancement: Digital Crystal
Clear
Perfect Motion Rate (PMR): 100 Hz
7 Specifications
Sound
Power and reception
Output power (RMS) @ 10% THD
- 22 - 24 inch models: 8W
- 26 inch models: 10W
- 32 - 42 inch models: 20W
Clear Sound
Mono / Stereo / Secondary audio
programming
Product specifications are subject to change
without notice.
Power
Mains power: AC 220-240 V (50-60
Hz)
Standby power consumption: < 0.3 W
Ambient temperature: 5 to 40 degree
Celsius
Display resolutions
For power consumption, see the
product specifications at
Computer formats - HDMI
(Resolution - refresh rate)
640 x 480 - 60 Hz
800 x 600 - 60 Hz
1024 x 768 - 60 Hz
1280 X 720 - 60 Hz
1280 X 768 - 60 Hz
1280 x 1024 - 60 Hz
1360 x 768 - 60 Hz
For Full HD TV only:
1680 x 1050 - 60 Hz
1920 x 1080 - 60 Hz
The power rating stated on the product
typeplate is the power consumption for this
product during normal household use (IEC
62087 Ed.2). The maximum power rating,
stated between brackets, is used for
electrical safety (IEC 60065 Ed. 7.2).
Reception
Antenna input: 75 ohm coaxial (IEC75)
TV system: DVB COFDM 2K/8 K
Video playback: NTSC, PAL, SECAM*
Digital TV: MPEG-4, DVB-T
(Terrestrial), DVB-C (Cable)
Tuner bands: VHF, UHF, S-Channel,
Hyperband
* Available on certain models only.
Display and sound
Picture / Display
Display type: LED backlight HD/Full HD
Diagonal size:
- 56 cm / 22 inches
- 61 cm / 24 inches
- 66 cm / 26 inches
- 81 cm / 32 inches
- 99 cm / 39 inches
- 107 cm / 42 inches
Aspect ratio: 16:9 (widescreen)
Panel resolution:
- Full HD: 1920x1080p
- HD: 1366 x 768
EN
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer formats - VGA
(Resolution - refresh rate)
Multimedia
640 x 480 - 60 Hz
800 x 600 - 60 Hz
1024 x 768 - 60 Hz
1280 x 1024 - 60 Hz
1360 x 768 - 60 Hz
1600 x 1200 - 60 Hz
1920 x 1080 - 60 Hz
Note: Multimedia file names must not
exceed 128 characters.
Supported multimedia connections
USB: Connect only those USB devices
that consume 500 mA of power or less.
- NTFS, FAT 16 (Read only)
- FAT 32
Video formats
(Resolution - refresh rate)
Supported image files
JPEG: *.jpg, *.jpeg, *.mpo
GIF (87a, 89a): *.gif
PNG: *.png
BMP: *.bmp, *.dib
JPS: *.jps
480i - 60 Hz
480p - 60 Hz
576i - 50 Hz
576p - 50 Hz
720p - 50Hz, 60 Hz
1080i - 50Hz, 60 Hz
1080p - 24Hz, 25Hz, 30Hz, 50Hz, 60 Hz
PNS: *.pns
BMS: *.bms
EN
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported audio/video formats
Supported audio/video formats
EN
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported audio/video formats
Supported audio/video formats
Supported audio/video formats
EN
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported audio/video formats
Supported audio formats
Supported audio formats
EN
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported subtitle formats
Character encoding
Windows-1250 (CP-1250): Central
Europe and Eastern Europe Latin
(Czech, Hungarian, Polish, Slovak,
Slovenian, Croatian, Romanian, Serbian)
Windows-1251 (CP-1251): Cyrillic
Windows-1252 (CP-1252): Western
Europe Latin
Windows-1253 (CP-1253): Greek
Windows-1254 (CP-1254): Turkish
UTF-8: Multi-byte character encoding
for Unicode
Connectivity
Rear
HDMI 1 ARC: HDMI Audio Return
Channel
SERV. U: Service port
CVBS/Y, Pb, Pr, Audio L/R: Composite
video and audio
VGA*: PC input
IR IN/OUT: RJ48 cable adaptor
DIGITAL AUDIO OUT: Coaxial
TV ANTENNA: 75 ohm coaxial (IEC)
SCART (RGB/CVBS): SCART adaptor
* Available on 22, 24, and 26-inch models
only.
EN
52
Download from Www.Somanuals.com. All Manuals Search And Download.
For 22-26 inch models
All screws: 10 mm
For 32 inch models
Side
CI: Common Interface
HDMI
USB
All screws: 12 mm
For 39-42 inch models
All screws: 14 mm
Headphones: stereo 3.5mm mini-jack
Supported TV mounts
You can mount your TV on the wall with a
compatible TV mount (sold separately).
Select the type of TV mount for your TV
screen size:
56 cm / 22 inches: 75mm x 75mm, M4
61 cm / 24 inches: 75mm x 75mm, M4
66 cm / 26 inches: 100mm x 100mm, M4
81 cm / 32 inches: 100mm x 100mm, M6
99 cm / 39 inches: 200mm x 200mm, M6
107 cm / 42 inches: 200mm x 200mm, M6
Note: Before you mount the TV on the wall,
remove the existing VESA screws on the
back panel.
Warning: Follow all instructions provided
with the TV mount. TP Vision Netherlands
B.V. bears no responsibility for improper
TV mounting that results in accident, injury
or damage.
Help version
UMv 300812131603 - 20130806
To prevent damage to cables and
connectors, leave a gap of at least 5.5 cm /
2.2 inches from the back of the TV.
Before you mount the TV on the wall, find
the correct length of the screw. To find the
length of the screw, add the thickness of
your wall mount to the screw length (y), as
shown in the graphic.
EN
53
Download from Www.Somanuals.com. All Manuals Search And Download.
connect, computer - 39
connect, digital camcorder - 38
connect, digital camera - 38
connect, disc player - 32
connect, external hard disk - 39
connect, game console - 36
connect, home theatre - 36
connect, recorder - 34
connect, TV receiver - 33
connect, USB device - 39
connected device, rename - 40
connectivity - 52
8 Index
A
amplifier, select output - 42
analogue channels, fine-tune - 26
analogue channels, install - 26
analogue channels, subtitles - 28
audio language - 28
auto subtitle shift - 43
Auto switch off, devices - 41
C
connectivity guide - 8
cables - 31
connectors - 31
CAM - 43
contact Philips - 8
CAM, enable - 43
controls - 9
CAM, insert - 43
channel list - 12
D
channel list, copy - 27
channels - 11
demo - 30
devices, watch - 40
channels, favourites - 12
channels, fine-tune (analogue) - 26
channels, hide or unhide - 12
channels, install (analogue) - 26
channels, install (automatic) - 26
channels, install (digital) - 26
channels, logo - 12
digital camcorder - 38
digital camera - 38
digital channels, install - 26
digital channels, subtitles - 28
digital radio - 12
disc player, connect - 32
display resolutions - 47
display specifications - 47
channels, reinstall - 30
channels, rename - 12
channels, sort - 12
E
channels, switch - 11
channels, update - 27
child lock - 23
EasyLink - 41
EasyLink, controls - 41
EasyLink, enable - 41
CI - 43
EasyLink, features - 41
EasyLink, onscreen control - 10
EasyLink, remote control - 41
EasyLink, TV speakers - 42
clock - 22
codecs, supported - 48
Common Interface - 43
Conditional Access Module - 43
EN
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy label - 8
O
energy-efficient settings - 7
EPG, broadcaster - 14
external hard disk - 39
online forum - 8
P
parental rating - 23
F
PC, display resolutions - 47
picture format - 13
favourite channels, list - 12
G
picture settings - 24
picture settings, reset - 25
Pixel Plus link - 43
game console, connect - 36
game settings - 21
placement, stand or wall - 4
placement, tips - 4
H
play, USB files - 14
HDMI - 31
power specifications - 47
presets, picture and sound - 13
product support - 8
HDMI ARC - 31
hearing-impaired access - 29
Help, version - 53
professional mode - 16
professional mode, access settings - 16
programme guide, broadcaster - 14
home mode - 30
home theatre, connect - 36
hotel information - 16
R
I
rear controls - 9
install channels, automatic - 26
recorder, connect - 34
recycle - 7
K
Kensington lock - 5
key beep - 29
reinstall - 30
remote control - 9
rename channels - 12
rename, connected device - 40
L
language, menu - 28
language, subtitles - 28
lock TV - 5
S
safety - 3
SCART - 31
M
screen care - 4
sensors - 9
mode, home or shop - 30
multimedia, play files - 14
multimedia, play options - 15
multimedia, supported formats - 48
MyChoice - 19
settings assistant - 24
settings, audio format - 25
settings, game - 21
EN
55
Download from Www.Somanuals.com. All Manuals Search And Download.
settings, picture - 24
settings, sound - 25
shop mode - 30
update, source list - 40
USB, play files - 14
V
sleep timer - 23
VGA - 32
sound settings - 25
sound settings, reset - 25
sound specifications - 47
source, select - 13
source, update - 40
standby - 10
visually impaired access - 29
volume - 11
W
wall mount - 53
standby LED - 9
Y
subtitles, analog - 28
subtitles, digital - 28
subtitles, language - 28
sustainability - 7
YPbPr, component video - 31
switch TV on, off - 10
T
teletext, search - 22
text 2.5 - 21
text, digital text - 22
text, dual screen - 21
text, enlarge - 21
text, language - 22
text, subpages - 22
text, Table Of Pages - 21
ThemeTV - 19
trademarks and copyrights - 6
TV controls - 9
TV guide, broadcaster - 14
TV receiver, connect - 33
TV speakers, mute - 11
U
universal access, enable - 29
universal access, hearing impaired - 29
universal access, visually impaired - 29
EN
56
Download from Www.Somanuals.com. All Manuals Search And Download.
All registered and unregistered trademarks are the property of their respective owners. Specifications are subject to change without notice.
Philips and the Philips’ shield emblem are registered trademarks of Koninklijke Philips Electronics N.V. and are used under license
from Koninklijke Philips Electronics N.V.
2013 © TP Vision Netherlands B.V. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|