AZ102_05_ENG_CCR 2010.3.30 15:14 Page 1
AZ102C
AZ102N
AZ102S
CD Soundmachine
Register your product and get support at
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
AZ102_05_ENG_CCR 2010.3.30 15:14 Page 3
2
DBB
ON
OFF
@
!
$
6 x R14 • UM-2 • C-CELLS
MW FM
STANDBY
CD
-
LINE IN
9
#
Download from Www.Somanuals.com. All Manuals Search And Download.
AZ102_05_ENG_CCR 2010.3.30 15:14 Page 4
7
3
8
4
5
PROG
X
6
ALL
Download from Www.Somanuals.com. All Manuals Search And Download.
AZ102_05_ENG_CCR 2010.3.30 15:14 Page 5
Important notes for users in the U.K.
Mains plug
This apparatus is fitted with an approved 13 Amp plug.To change a fuse in this type of
plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fix new fuse which should be a BS1362 3 Amp, A.S.T.A. or BSI approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an
appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a
value of 3 Amp. If a plug without a fuse is used, the fuse at the distribution board
should not be greater than 3 Amp.
Note:The severed plug must be disposed of to avoid a possible shock hazard should it
be inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following code: blue = neutral (N),
brown = live (L). As these colours may not correspond with the colour markings iden-
tifying the terminals in your plug, proceed as follows:
•
•
•
Connect the blue wire to the terminal marked N or coloured black.
Connect the brown wire to the terminal marked L or coloured red.
Do not connect either wire to the earth terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain that the cord grip is clamped over the
sheath of the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may require consent. See Copyright Act 1956 and
The Performer’s Protection Acts 1958 to 1972.
Download from Www.Somanuals.com. All Manuals Search And Download.
AZ102_05_ENG_CCR 2010.3.30 15:14 Page 6
English
Controls/Power Supply
Congratulations on your purchase, and
CAUTION
-Visible and invisible laser radiation.
welcome to Philips!To fully benefit
from the support that Philips offers,
register your product at
If the cover is open, do not look at
the beam.
- High voltage! Do not open.You run
the risk of getting an electric shock.
The machine does not contain any
user-serviceable parts.
Supplied Accessories
– AC power cord
- Modification of the product could
result in hazardous radiation of
EMC or other unsafe operation.
- Use of controls or adjustments or
performance of precedures other
than herein may result in unsafe
operation.
Top/front panels (See 1)
1
2
VOLUME
–
adjusts volume level.
SHUFFLE – plays all tracks in random order
3 REPEAT
–
repeats a track/
CD program/entire CD.
This set complies with the radio
interference requirements of the
European Union.
4
2 ;
–
starts or pause CD playback
selects the next/previous track
§
∞
–
– searches forwards/backwards (press and
hold the button) within the current track
Notes for battery disposal
Your product contains batteries
covered by the European
Directive 2006/66/EC, which can-
not be disposed with normal
9
–
–
stops CD playback;
erases a CD program
5 PROG – programs tracks and reviews the
program
6 LIFTTO OPEN – opens/closes the CD
household waste. Please inform
door.
yourself about the local rules on separate col-
lection of batteries because correct disposal
helps to prevent negative consequences for
the environmental and human health.
7 TUNING – tunes to radio stations
8
9
Display
–
shows the CD functions
Back panel (See 1 and 2)
Source selector: CD, FM, MW, OFF
Power Supply
Whenever convenient, use the power supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
–
selects CD or radio source of sound
–
power off switch
0 Telescopic antenna - improves FM reception.
! AC MAINS~ - inlet for power cord.
Batteries (not included)
@
#
DBB
–
turns the bass enhancement on/off.
1
2
Open the battery door and insert 6 batteries,
type R-14, UM-2 or C-cells, (preferably alka-
line) with the correct polarity as indicated by the
"+" and "–" symbols inside the compartment.
LINE-IN – inlet for external audio source.
Bottom panel
$ Battery door – Press on the arrow and
push to insert 6 x 1.5V R-14/ UM-2/ C-
cells.
Replace the battery door, making sure the bat-
teries are firmly and correctly in place.The set is
now ready to operate.
Download from Www.Somanuals.com. All Manuals Search And Download.
AZ102_05_ENG_CCR 2010.3.30 15:14 Page 7
Power Supply
General Operation /Tuner
Batteries contain chemical substances, so
they should be disposed of properly.
General operation
•
•
Incorrect use of batteries can cause electrolyte
leakage and will corrode the compartment or
cause the batteries to burst:
Do not mix battery types: e.g. alkaline with car-
bon zinc. Only use batteries of the same type
for the set.
Switching on and off and selecting the
function
To select your sound source, adjust the
Source selector to: CD, FM or MW.
1
2
To switch off the set, adjust the Source
•
•
When inserting new batteries, do not try to mix
old batteries with the new ones.
Remove the batteries if the set is not to be used
for a long time.
selector to OFF position.
3
To switch to LINE IN mode, connect an
external audio source to the LINE-IN inlet.
Using AC power
Helpful hints:
WARNING:Always check you have com-
pletely switched off the set, before you
change or disconnect power supply.
•
•
The set switches to LINE IN mode auto-
matically when an external audio source is
connected, no matter the set is in CD, FM
or MW mode.
1
2
Check if the power voltage, as shown on
the type plate located on the bottom
of the set, corresponds to your local power
supply. If it does not, consult your dealer or
service center.
The LINE-IN inlet is not for earphones.
Adjusting volume and sound
Adjust the sound with the VOLUME and
DBB controls.
Connect the power cord to the AC
MAINS~ inlet and the wall socket.The set is
now connected and ready for use.
3
4
To switch the set off completely, withdraw the
power cord from the wall socket.
Radio reception
Adjust the Source selector to FM or
MW.
Install the unit near the AC outlet and where
the AC power plug can be easily reached.
1
2
•
Disconnect the power cord from the wall
socket to protect your set during heavy thun-
derstorms. Children could seriously injure
themselves as the free end of the cable may
still be live if only the connector is removed
from the MAINS socket at the back of the
unit.
Turn TUNING to tune to a station.
Helpful hints:
To improve radio reception
•
For FM, extend, incline and turn the telescop-
ic antenna for best reception. Reduce its
length if the signal is too strong.
The type plate is located on the bottom
of the set.
•
For MW, the set uses a built-in antenna.
Direct this antenna for best reception by
turning the whole set.
Helpful hints:
–
To avoid unnecessary energy consumption,
always adjust the Source selector to OFF
after using the set.
Download from Www.Somanuals.com. All Manuals Search And Download.
AZ102_05_ENG_CCR 2010.3.30 15:14 Page 8
CD Player
Playing a CD
Selecting a different track
•
•
This CD player plays Audio Discs including
CD-Recordables (CD-R) and CD-Rewritables
(CD-RW).
•
•
Press ∞/ § once or repeatedly until the
desired track number appears in the display.
In the pause/stop position, press 2; to start
playback.
MP3, CD-ROM, CD-I, CDV,VCD, DVD or
computer CDs are not possible for playback.
Finding a passage within a
track
During playback, press and hold ∞ or § .
➜ The CD is played at high speed and with
reduced volume.
IMPORTANT!
CDs encoded with copyright protection
technologies by some record companies may
be unplayable by this product.
1
2
1
2
Adjust the Source selector to CD.
When you recognize the passage you want,
release ∞ or § to resume normal playback.
Open the CD door, and insert a CD with
the printed side facing up, then press the CD
door gently to close.
Helpful hints:
When your searching reaches the end of the
last track, the CD goes to stop mode.
–
➜ Display shows --, and later the total
number of tracks. (See 3)
3
4
Press 2; to start playback.
To pause playback, press 2;
.
➜
Display: 2 flashes. (See 4)
5
6
To resume, press 2; again.
To stop CD playback, press
9.
Helpful hints:
CD play will also stop when:
–
–
–
you open the CD door;
you select FM MW or OFF sound source;
the CD has reached the end.
,
Download from Www.Somanuals.com. All Manuals Search And Download.
AZ102_05_ENG_CCR 2010.3.30 15:14 Page 9
CD Player
Programming track num-
bers
You may store up to 20 tracks in the desired
sequence. If you like, store any track more
than once.
Different play modes:
REPEAT. and SHUFFLE
(See 6, 7)
REPEAT
You can play the current track or the whole
disc repeatedly, and combine REPEAT
modes with PROG (PROGRAM).
1
In the stop position, press PROG to
activate programming.
➜ Display: PROG and 00 flash. (See 5)
REP – plays the current track continuously.
2
3
Press
number.
∞
or
§
to select your desired track
REP ALL – repeats the entire CD/program
1
To select play mode, press REPEAT once or
more.
➜ The display shows REP icon or REP
ALL icon.
Press 2; to start playback if in the stop/pause
position.
To return to normal playback, press REPEAT
repeatedly until the modes are no longer dis-
played.
– You can also press 9 to cancel your play
mode.
Press PROG to store the desired track
number.
➜ Display: PROG and 00 flash for you to
program the next track..
2
3
4
Repeat steps 2 to 3 to select and store all
desired tracks in this way.
➜ If you attempt to store more than 20
tracks, no track can be selected and the
display shows --.
5
To play your program, press
2/;.
SHUFFLE
You can play all the tracks in random order.
Helpful hints :
–
When playback of your program comes
to the stop position, your set will return
to normal playback.To re-enter program
mode, press PROG in the stop position.
1
2
In the stop position, press SHUFFLE to
switch on shuffle play.
➜ Display shows SHUFFLE icon.
To switch off shuffle play, press 9.
Helpful hints:
During the shuffle play, when REP function is
Reviewing the program
–
In the stop position, press PROG repeatedly
to see your stored tracks.
selected, it will play the current shuffled track
repeatedly, or when the REP ALL function is
selected, it will repeat the shuffle play of the
entire CD.
Erasing a program
You can erase the contents of the memory
by:
– in the stop position, press PROG to enter
program mode, and then press 9.
– selecting FM
,
MW or OFF;
– opening the CD door;
Download from Www.Somanuals.com. All Manuals Search And Download.
AZ102_05_ENG_CCR 2010.3.30 15:14 Page 10
Maintenance & Safety (See 8)
CD player and CD handling
Safety information
•
If the CD player cannot read CDs correctly,
use a cleaning CD to clean the lens before
taking the set to repair.
•
•
Place the set on a flat, hard and stable surface
so that the system does not tilt.
Where the MAINS plug or an appliance cou-
pler is used as the disconnect device, the dis-
connect device shall remain readily operable.
•
•
The lens of the CD player should never be
touched!
Sudden changes in the surrounding
•
Do not expose the set, batteries, CDs to
humidity, rain, sand or excessive heat caused
by heating equipment or direct sunlight.
temperature can cause condensation on the
lens of your CD player. Playing a CD is then
not possible. Do not attempt to clean the
lens but leave the set in a warm environment
until the moisture evaporates.
•
•
The apparatus shall not be exposed to drip-
ping or splashing.
Adequate ventilation with a minimum gap of
15cm (6 inches) between the ventilation
holes and surrounding surfaces is necessary
to prevent heat build-up.
•
•
Always close the CD door to avoid dust on
the lens.
To clean the CD, wipe in a straight line from
the center towards the edge using a soft,
lint-free cloth. Do not use cleaning agents as
they may damage the disc.
•
Do not cover the ventilation openings with
items such as newspapers, table-cloths, cur-
tains, etc.
•
Never write on a CD or attach any stickers
to it.
•
•
•
No objects filled with liquids, such as vases,
shall be placed on the apparatus.
No naked flame sources, such as lighted can-
dles, should be placed on the apparatus.
The mechanical parts of the set contain self-
lubricating bearings and must not be oiled or
lubricated.
•
To clean the set, use a dry cloth. Do not use
any cleaning agents containing alcohol, ammo-
nia, benzene or abrasives as these may harm
the housing.
Download from Www.Somanuals.com. All Manuals Search And Download.
AZ102_05_ENG_CCR 2010.3.30 15:14 Page 11
Troubleshooting
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
WARNING:
Do not open the set as there is a risk of electric shock. Under no
circumstances should you try to repair the set yourself, as this will
invalidate the guarantee.
Problem
Note:
Make sure the CD is not encoded with copy-
right protection technologies, as some do not
conform to the Compact Disc standard.
– Possible cause
• Remedy
No sound /power
The CD skips tracks
– Volume not adjusted
– CD damaged or dirty
• Adjust theVOLUME
• Replace or clean CD
– Power cord not securely connected
• Connect the AC power cord properly
– Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
– CD contains non-audio files
– Program/shuffle is active
• Quit program/shuffle mode
Note: A CD badly scratch or dirty may result in
improper operation.
• Press ∞ , § once or more to skip to a CD audio
track, instead of the data file.
Display does not function properly / No
reaction to operation of any of the
controls
– Electrostatic discharge
• Switch off and unplug the set. Reconnect after a
few seconds
--, Er or 01 indication
– No CD inserted
•
Insert a CD
– CD badly scratched or dirty
Replace/ clean CD, see Maintenance
•
– Laser lens steamed up
• Wait until lens has cleared
– CD-R/CD-RW is blank or not finalized
•
Use a finalized CD-R/CD-RW or suitable CD
Audio disc only
Download from Www.Somanuals.com. All Manuals Search And Download.
AZ102_05_ENG_CCR 2010.3.30 15:14 Page 12
Environmental information
All unnecessary packaging material has been omitted.The packaging can be easily separated
into three materials: cardboard, polystyrene and plastic.
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packaging, dead batteries and old equipment.
Disposal of your old product
Your product is designed and manufactured with high quality materials
and components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to
a product it means the product is covered by the
European Directive 2002/96/EC.
Please inform yourself about the local separate collection system for electrical
and electronic products.
Please act according to your local rules and do not dispose of your old products
with your normal household waste.The correct disposal of your old product will
help prevent potential negative consequences for the environment and human
health.
Download from Www.Somanuals.com. All Manuals Search And Download.
AZ102_05_ENG_CCR 2010.3.30 15:14 Page 13
Meet Philips at the Internet
W
AZ102C
AZ102N
AZ102S
AZ102B
CLASS 1
LASER PRODUCT
Printed in China
AZ102_05_UM_V3.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|