Digital Camera
Operating Manual
To ensure the best performance from
your camera, please read the Operating
Manual before using the camera.
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR SAFETY
We have paid close attention to the safety of this product. When using
this product, we request your special attention regarding items marked
with the following symbols.
This symbol indicates that violating this item could
cause serious personal injury.
Warning
This symbol indicates that violating this item could
cause minor or medium personal injury, or material
loss.
Caution
Warning
• Do not disassemble or modify the camera. High voltage areas are present inside
the camera, with the risk of electric shock.
• If the camera interior is exposed due to dropping or otherwise damaging the
camera, never touch the exposed portion. There is the risk of electric shock.
• Wrapping the strap around your neck is dangerous. Take care that small children
do not hang the strap over their necks.
• To avoid the risk of it being swallowed by mistake, keep the SD Memory Card /
MultiMediaCard out of the reach of small children. Seek medical attention
immediately if accidentally swallowed.
• Always use the AC adapter specified exclusively for this product, with the specified
power and voltage. Using an AC adapter not exclusive to this product, or using the
exclusive AC adapter with an unspecified power or voltage can cause a fire, electric
shock, or camera breakdown.
• If any irregularities occur during use, such as smoke or a strange odor, stop use
immediately, remove the batteries or the AC adapter, and contact your nearest
PENTAX service center. Continued use could cause a fire or electric shock.
• During thunderstorms, unplug and discontinue use of the AC adapter. Continued
use could cause equipment failure, a fire, or electric shock.
Caution
• Do not short the battery or dispose of the battery in fire. Do not disassemble the
battery. The battery could explode or catch fire.
• Do not charge any batteries other than rechargeable Ni-MH batteries. The battery
could explode or catch fire. Of the batteries that can be used in this camera, only
the Ni-MH battery can be recharged.
• Remove the battery from the camera immediately if it becomes hot or begins to
smoke. Be careful not to burn yourself during removal.
• Some portions of the camera heat up during use. There is the risk of low
temperature burns when holding such portions for long periods.
• Do not place your finger on the flash when it is discharging as there is a risk of
burns.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling the Camera
• Always confirm that the camera is working properly when the camera has not been
used for a long time, or before important occasions (weddings, trips, etc.). PENTAX
is not responsible for consequential damages (costs incurred for photography, lost
profits, etc.) arising from failure of this product.
• The lens on this camera is not exchangeable. The lens is not removable.
• Do not clean the product with organic solvents such as thinner, alcohol, or benzene.
• Do not subject to high temperatures or high humidity. Do not leave the camera in a
vehicle, as the temperature can get very high.
• Do not store the camera with preservatives and chemicals. Storage in high
temperatures and high humidity can cause molding. Remove from case and store
in a dry and well-ventilated location.
• Do not subject the camera to strong vibrations, shocks, or pressure. Use a cushion
to protect the camera from vibrations of motorcycles, automobiles, or ships.
• The temperature range for camera use is 0°C to 40°C.
• The LCD display may appear black under high temperatures, but will return to
normal as temperatures normalize.
• The LCD display may respond more slowly at low temperatures. This is due to
liquid crystal properties, and is not a fault.
• Periodic inspections are recommended every one to two years to maintain high
performance.
• Sudden temperature changes will cause condensation on the inside and outside of
the camera. Place the camera in your bag or a plastic bag, retrieving the camera
after decreasing the temperature difference.
• Avoid contact with garbage, mud, sand, dust, water, toxic gases, or salts. These
could cause a camera breakdown. Wipe dry any rain or water drops on the camera.
• See “Precautions when using an SD Memory Card / MultiMediaCard” (p.18) for
details on the SD Memory Card / MultiMediaCard.
• Please do not press forcefully on the LCD monitor. This could cause breakage or
malfunction.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Water-resistant Feature
• This camera conforms to JIS, (Japanese Industrial Standard) Class 5 water
resistant, (Direct jetting water under defined conditions shall have no harmful effect)
and Class 7 water resistant, (Water shall not enter the enclosure when it is
immersed in water up to 30 minutes at a depth of 1 meter.)
• This camera cannot be used underwater.
• Immediately after using the camera, be sure to carefully wipe off any water or dirt
with a soft, dry cloth.
• Do not place the camera directly on the sand at a beach or other location. Exposure
to large amounts of sand or dirt may damage the camera.
• The inside of the camera is not water resistant. Before using the camera, be sure
the terminal cover and battery/card cover are securely closed.
When replacing the battery or inserting or removing the memory card, carefully
wipe off any water or dirt and open the cover in a location where the camera is not
exposed to water or dirt. If water, sand, or dirt gets inside the camera, the camera
may become damaged.
• If the camera becomes exposed to large amounts of dirt or salt water, make sure
that the power is off and the terminal cover and battery/card cover are securely
closed, and then carefully rinse off the camera under slowly running tap water or in
a shallow basin filled with fresh water for two to three minutes.
• This camera should not be immersed in water for periods longer than thirty minutes
at a time or exposed to extreme water pressure.
• Do not clean the camera with soapy water, mild detergent, or alcohol as this may
reduce the effectiveness of the camera’s water-resistant feature. Be careful not to
expose the camera to coffee or other beverages, as this may also reduce the
effectiveness of the camera’s water-resistant feature.
• Before using the camera, be sure to wipe off any sand or debris from the water-
resistant packing and the areas between the camera and the packing. Any
scratches or damage to the packing or the areas between the camera and the
packing or any peeling of the packing may reduce the effectiveness of the camera’s
water-resistant feature. If this should occur, please call the Pentax Customer
Service Department.
• The accessories of SD card, battery, USB cable and AV cable are not water
resistant.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Handling the Camera........................................................................2
CONTENTS......................................................................................4
Getting Started
Initial Settings .....................................................................................20
Setting the Display Language.........................................................20
Quick Start
Taking Still Pictures............................................................................24
Capture Mode.................................................................................30
Taking Pictures
36
Setting the Capture Functions...........................................................36
Changing the Mode ........................................................................36
Changing Focus Settings ...............................................................37
Selecting the Flash Mode...............................................................39
Selecting the Recorded Pixels........................................................40
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Color Saturation .................................................................48
Continuous Shooting (Continuous Shooting/Multi Continuous
Shooting) ........................................................................................56
Taking Movie Pictures (Movie Picture Mode).................................63
Pictures...........................................................................................65
Playback/Deleting
Deleting Images ..................................................................................77
Deleting All Images.........................................................................79
Protecting Images from Deletion (Protect) .....................................80
Viewing Images on a TV.....................................................................81
Setting the Printing Service (DPOF)..................................................82
Printing Individual Image ................................................................82
Printing All Images..........................................................................84
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing/Settings
Editing Images ....................................................................................85
Resetting to Default Settings [Reset]..............................................99
Appendix
List of City Names.............................................................................103
Messages...........................................................................................104
Optional Accessories .......................................................................105
Troubleshooting................................................................................106
Main Specifications ..........................................................................108
WARRANTY POLICY.........................................................................110
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents of This Manual
This operating manual contains the following chapters.
1
2
3
4
5
6
7
1 Getting Started ––––––––––––––––––––––––––––––––––––––––
Explains your first steps, from purchasing the camera to taking pictures. Be
sure to read it and follow the instructions.
2 Quick Start––––––––––––––––––––––––––––––––––––––––––––
Explains the simplest way to take pictures and play back images. Use it if you
want to get started right away. It also explains how to use an SD Memory
Card and MultiMediaCard.
3 Common Operations –––––––––––––––––––––––––––––––––––
Explains common operations such as button functions and using the menus.
See “Taking Pictures”, “Playback/Deleting”, and “Settings” chapters for more
details.
4 Taking Pictures ––––––––––––––––––––––––––––––––––––––––
Explains various ways to capture images, and how to set the relevant
functions, such as setting the virtual mode dial to change capture modes, and
selecting the right picture mode for the current scene.
5 Playback/Deleting ––––––––––––––––––––––––––––––––––––––
Explains how to play back images on the camera or a TV, and how to delete.
6 Editing/Settings––––––––––––––––––––––––––––––––––––––––
Explains how to edit images and set up the functions of the camera.
7 Appendix –––––––––––––––––––––––––––––––––––––––––––––
Explains troubleshooting, and introduces accessories sold separately.
The symbols used in this operating manual are explained below.
Shows reference page number explaining a related operation.
Shows information useful to know.
Shows precautions to take when operating the camera.
e
Icons for functions available in a capture mode are shown at the
beginning of a section.
CF
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Package Contents
Camera
Strap
Software
Optio 33WR
O-ST5 (*)
(CD-ROM) S-SW13
AV cable
I-AVC7 (*)
USB cable
I-USB7 (*)
AA Alkaline batteries (2)
(PC Connection Manual)
Viewing Your Digital
Camera Images
On Your PC
SD Memory Card
(16 MB)
Operating Manual
(this manual)
Operating Manual
(PC Connection Manual)
(*) Items marked with an asterisk are also available as optional accessories.
For other optional accessories, see “Optional Accessories” (p.105) .
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Parts
Front view
Shutter release button
Power switch
Strap lug
Microphone
Lens
Flash
Self-timer lamp
Water-resistant packing
Battery/card cover
Back view
Terminal cover
Speaker
Viewfinder
DC input terminal
USB/AV output terminal
Water-resistant packing
LCD monitor
Tripod socket
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Operating Parts
AF status lamp (green)
Flash status lamp (red)
Zoom/f/ybutton
Playback Qbutton
OK button
Four-way controller
MENU button
)/i button
b/Z button
Obutton
Guide display
A button operation guide is displayed on the LCD monitor during
operation.
The buttons are indicated as shown below.
Four-way controller (2)
Four-way controller (3)
Four-way controller (4)
Four-way controller (5)
MENU button
2
3
4
5
Zoom/f/ybutton
(Digital zoom and magnified
playback only)
y
i button
Z button
OK button
Shutter release button
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering the Camera
1
(Using AA batteries)
(Using CR-V3)
Installing the Batteries
Install batteries in the camera. Use one CR-V3, or use two AA lithium
batteries, AA Ni-MH batteries, or AA alkaline batteries.
Turn off the camera when setting batteries.
Wipe away water or dirt from the camera with a dry cloth before setting
batteries.
Do not set batteries with wet or dirty hands.
1
2
3
Slide the battery cover in the direction of the arrow
and flip open.
,
Insert the batteries according to the +-indicator in
the battery chamber.
Wipe away any sand or debris on the water-resistant
packing and the areas between the camera and the
packing.
4
Close the battery cover and push horizontally to lock.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
When using for a prolonged period, please use the AC adapter D-AC5
(p.15).
• AA lithium, AA alkaline battery, and the CR-V3 battery are not
rechargeable.
switch is on.
1
• When you will not use the camera for a long while, remove the
batteries. Otherwise, the battery may leak.
• If the date and time settings have been reset when you insert new
batteries after a long while, follow the procedure for “Setting the Date
and Time” (p.22).
• Insert batteries correctly. Wrong insertion can cause a camera
breakdown.
Number of Captures and Playback Time (room temperature, new
batteries)
• Taking pictures (50% flash usage)
• Playback
Image Storage
Capacity
Playback time
Approx. 230
min.
CR-V3
Approx. 540
Approx. 360
Approx. 300
Approx. 125
CR-V3
Approx. 160
min.
AA lithium batteries
Ni-MH batteries
AA alkaline batteries
AA lithium batteries
Ni-MH batteries
AA alkaline batteries
Approx. 125
min.
Approx. 75
min.
• These figures are based on PENTAX measuring conditions. They may vary by
capture mode or shooting conditions.
• Battery performance temporarily decreases as the temperature
decreases. When using the camera in cold climates, have extra
batteries on hand, keeping them warm in your pocket. Battery
performance will return to normal when returned to room temperature.
• When traveling overseas, taking pictures in cold climates, or when you
will be taking a lot of pictures, please have extra batteries ready.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Level Indicator
You can check the battery level with the *display on the LCD monitor.
(lit green)
:
:
:
:
:
Adequate power remains.
*
,
;
%
1
↓
(lit green)
Battery is running low.
↓
(lit yellow)
Battery is running very low.
Battery is exhausted.
↓
(lit red)
↓
No battery power
After displaying this message, the camera turns off.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
f
c
d
1
e
Using the AC Adapter
When using the LCD monitor for a long time or when connecting to your
PC, we recommend using the AC adapter D-AC5 (sold separately).
1
2
Make sure the camera is turned off before opening the
terminal cover.
Connect the DC terminal on the AC adapter to the DC
input terminal on the camera.
3
4
Connect the AC plug cord to the AC adapter.
Plug the AC plug cord into the power outlet.
• Make sure the camera is turned off before connecting or disconnecting
the AC adapter.
• Make sure connections are secure between the camera, AC adapter,
AC plug cord terminal, and the power outlet. Disconnections while the
camera is recording or reading data will corrupt your data.
• When using the AC adapter, be sure to read the AC adapter D-AC5
operating manual.
• Connecting the AC adapter will not charge the rechargeable batteries
in your camera.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing / Removing the SD Memory Card /
MultiMediaCard
SD Memory Card/
MultiMediaCard
1
Battery/card cover
c
e
d
The image or recorded audio is recorded on the SD Memory Card /
MultiMediaCard. Be sure the camera is turned off before inserting or
removing the SD Memory Card / MultiMediaCard.
Turn off the camera before setting or removing the card.
Wipe away water or dirt from the camera with a dry cloth before setting
or removing the card.
Do not set or remove the card with wet or dirty hands.
Installing
1
2
Slide the battery/card cover to the direction of the arrow
, and flip open.
With the label (or 2 symbol) of the SD Memory Card /
MultiMediaCard toward the lens, insert the card into the
card slot until the card clicks. If the card is not inserted
properly, images and sound may not be recorded
correctly.
3
4
Wipe away any sand or debris on the water-resistant
packing and the areas between the camera and the
packing.
Close the battery/card cover.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing
1
2
3
Slide the battery/card cover in the direction of the arrow
, and flip open.
1
Press the SD Memory Card / MultiMediaCard in the
direction of the arrow e, then pull out the ejected card.
Wipe away any sand or debris on the water-resistant
packing and the areas between the camera and the
packing.
4
Close the battery/card cover.
• If the battery/card cover is opened while saving an image, the save is
interrupted (the image is not saved).
Approximate Number of Shots, Recorded Pixels, and Quality
Levels
Quality level
Recorded Pixels
2048×1536
1600×1200
1024×7680
640×480
Movie picture Movie picture
(320×240) (160×120) recording
Voice
Best/
Better/
Good/
E
C
D
7
12
20
45
82
18
27
11
25
53
40 sec. 150 sec. 30 min.
56
100
• These figures show the number of shots when using a 16MB SD Memory Card.
• These figures are based on PENTAX standard shooting conditions, and may
vary depending on the subject, shooting conditions, capture mode, and SD
Memory Card used.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
• Precautions when using an SD Memory Card / MultiMediaCard
• Make sure the camera is turned off before opening the
battery/card cover.
• The SD Memory Card has a write-protect switch. Moving
the switch to the [Lock] position prevents the recording and
erasing of data and the formatting of the card and protects
all saved data.
Write-protect
switch
1
• SD Memory Cards/MultiMedia Cards formatted on a PC or
device other than the camera cannot be used. Be sure to
format the card with the camera.
• The SD Memory Card / MultiMediaCard may be hot when
removed immediately after camera use. Please be careful.
• Do not remove the card or turn off the camera when
MultiMediaCard, or when connected to a PC with the USB cable. This could
cause data loss or card damage.
• Do not bend the SD Memory Card / MultiMediaCard or subject it to violent
impact. Do not get it wet or leave it in a high temperature location.
• New cards or cards used in another camera must be formatted before use. For
more information about formatting the card, see “Formatting an SD Memory
Card / MultiMediaCard” (p.90).
• Do not remove the SD Memory Card / MultiMediaCard while the card is being
formatted. The card may be damaged and become unusable.
• Data stored on an SD Memory Card / MultiMediaCard may be erased under
the following conditions. PENTAX does not accept any liability regarding
erased data.
• When the user mishandles the SD Memory Card / MultiMediaCard
• When the SD Memory Card / MultiMediaCard is placed in a location with
static electricity or electrical interference
• When the card is not used for a long time
• When the card, the AC adapter, or battery is removed while recording or
reading data on the SD Memory Card / MultiMediaCard
• The SD Memory Card / MultiMediaCard has a finite operating life. The stored
data may become unreadable after long periods of disuse. Please periodically
backup important data onto your PC.
• Please avoid using or storing your card where static electricity or electrical
interference can occur.
• Do not use or store your card where it may be exposed to sudden temperature
changes, condensation, or direct sunlight.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Camera On and Off
1
Power switch
Playback button
1
Press the power switch.
The camera will turn on.
Press the power switch again to turn the camera off.
Card check feature
When the camera is turned on, the camera
automatically checks for a card. If there is no SD
Memory Card / MultiMediaCard inside the camera,
^ appears on the LCD monitor.
If the write protect switch is set to LOC, ^ appears
on the LCD monitor, indicating that images and
audio cannot be recorded.
0
10/10/2003
11:20
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial Settings
Power switch
1
Four-way controller
OK button
MENU button
the procedure below to set the display language, Home Town, DST,
video output format and current date and time. If the date and time that
appear at the bottom right of the LCD monitor when you turn the camera
on for the first time is not the current time, follow the instructions for
“Changing the Date Style and Date / Time” (p.92) to set the correct date
and time.
Once the above Initial Settings are performed, the Initial Setting screens
do not appear on your LCD monitor again.
Setting the Display Language
You can choose the language in which the menus, error messages, etc.
are displayed from the following: English, French, German, Spanish,
Italian, Russian, Chinese and Japanese.
1
2
Turn the camera on.
Initial Setting
Language/
City
English
NYC
Use the four-way controller (45) to
select the display language.
DST
Video Out
NTSC
Exit OK OK
MENU
3
Press the four-way controller (3).
The screen for setting the City will be displayed.
You can change the setting after it has been made. Refer to “Changing
the Display Language” (p.94).
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Home Town
You can choose the city (Home Town) in which you will use the camera.
1
Press the four-way controller (45)
to select the desired city (Home
Town).
1
Initial Setting
Language/
City
English
NYC
DST
Video Out
NTSC
Exit OK OK
MENU
2
The screen for setting the D.S.T. will be displayed.
• See p.103 for the list of cities and corresponding code names.
• You can change the setting after it has been made. Refer to “Setting
World Time” (p.93).
Setting the D.S.T. Mode
You can choose whether or not to display the D.S.T (Daylight Saving
Time) mode.
1
Use the four-way controller (45) to
select O (on) or P (Off).
Initial Setting
Language/
City
English
NYC
DST
The default setting is P (Off).
Video Out
NTSC
Exit OK OK
MENU
2
Press the four-way controller (3).
The screen for setting the next item will be displayed.
You can change the setting after it has been made. Refer to “Setting
World Time” (p.93).
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Video Output Format
You can choose the output format (NTSC or PAL) for taking or playing
back pictures using a TV monitor.
1
1
Use the four-way controller (45) to
select the video output format.
Initial Setting
Language/
City
English
NYC
DST
The default setting is NTSC.
Video Out
NTSC
2
The screen for setting the date and time will be
displayed.
Exit OK OK
MENU
You can change the setting after it has been made. Refer to “Selecting
the Video Output Format” (p.99).
Setting the Date and Time
Set the current date and time, and the display style.
1
Press the four-way controller (23) to
select the date and time display style.
Date Adjust
Date Style
mm/dd/yy 24h
01
/
01
/
2003
00 : 00
Exit OK OK
MENU
2
3
Press the four-way controller (5).
23 are displayed above and below “24h”.
Date Adjust
Date Style
mm/dd/yy 24h
01
/
01
/
2003
00 : 00
Exit OK OK
MENU
Press the four-way controller (23) to select 24h (24-
hour display) or 12h (12-hour display).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
6
7
Press the four-way controller (5).
23 is displayed above and below the month.
Date Adjust
Date Style
mm/dd/yy 24h
01
/
01
/
2003
00 : 00
1
Exit OK OK
MENU
Press the four-way controller (23)
to change the month.
Date Adjust
Date Style
mm/dd/yy 24h
03
/
01
/
2003
00 : 00
Exit OK OK
MENU
Press the four-way controller (5).
23 are displayed above and below the date.
Date Adjust
Date Style
mm/dd/yy 24h
03
/
01
/
2003
00 : 00
Exit OK OK
MENU
Press the four-way controller (23)
to set the date and press the four-way
controller (5) again.
Date Adjust
Date Style
mm/dd/yy 24h
03
/
01
/
2003
23 are displayed above and below the year.
00 : 00
Exit OK OK
MENU
8
9
Repeat step 7 to set the year, hour,
and minutes.
Press the OK button.
The camera is ready to take a picture. When you set the date and time
using the MENU button, you will return to the Menu screen. Press the
Playback/OK button again.
• If you press the MENU button before initial settings are complete, your
settings will be cancelled, but you can take pictures. If this happens,
the Initial Settings screen is displayed the next time the camera is
turned on.
• Your settings can be changed later from the Menu screen. To access
the menu, see “Changing the Date Style and Date / Time” (p.92).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
Taking Still Pictures
Power switch
Shutter release button
2
Zoom/f/ybutton
AF status lamp (green)
Flash status lamp (red)
LCD monitor
This is the simplest way to take still pictures. The flash discharges
automatically based on light conditions by the default setting.
1
2
Press the power switch.
The camera will turn on.
Confirm the subject and shooting
information on the LCD monitor.
100
The focus frame at the center of the LCD
screen indicates the zone of automatic
focusing. Press the Zoom button to change the
size of the subject.
10/10//2003
11:20
Focus frame
x
Subject becomes bigger.
wSubject becomes smaller.
You can check the size of the subject by looking through the
viewfinder.
3
Press the shutter release button.
The image will be displayed on the LCD monitor for 1.5 seconds
(Instant Review) and recorded on the SD Memory Card /
MultiMediaCard. (The green and red lamps next to the viewfinder blink
alternately while the image is being recorded on the SD Memory Card
/ MultiMediaCard.)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Pressing the Shutter Release Button
The shutter release button works in two steps.
• Press halfway
Lightly press (halfway) the shutter release button to lock the focus position,
exposure, and white balance.
The shutter speed and aperture settings are only displayed when pressing the
shutter release button halfway.
2
You can find the following information on the LCD monitor, the AF status lamp and
the flash status lamp.
1. Focus frame
The frame lights green when focused. It is not displayed when out of focus.
2.Focus status lamp & Flash status lamp
AF status lamp (green)
Subject is in focus.
Flash status lamp (red)
Flash is ready.
Lit
Blink
Subject is out of focus.
Now charging.
You cannot take a picture while the flash is charging.
• Press down fully
Press the shutter release button all the way down (fully) to take a picture.
• Poor focusing conditions
The camera may not focus if the subject is in a condition shown below. Lock the
focus on something that is the same distance away as the subject (press the
shutter release button halfway), and press the shutter release button fully when
you have composed your picture.
• Things that lack contrast such as a blue sky or white wall.
• Dark places or objects, and conditions that prevent light being reflected back.
• Horizontal lines or intricate patterns
• Fast moving objects
• When an object in the foreground and one in the background are in the same
picture.
• Strongly reflected light or strong backlighting (bright background)
Instant Review
Instant Review displays the image for 1.5 seconds. Pressing the i
button during Instant Review displays the Delete menu. Select [Delete]
and press the OK button to delete the image.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
Playing Back Still Pictures
Delete button
Playback button
OK button
2
LCD monitor
Playing Back Images
To play back still pictures:
1
Press the playback button after
taking a picture.
Start
100-0001
The captured image is displayed on the LCD
monitor.
10/10//2003
11:20
Playing Back Previous or Next Images
You can play back still pictures, cycling through one at a time.
1
2
Press the Playback button after taking a picture.
The captured image is displayed on the LCD monitor.
Press the four-way controller (45).
Displays the previous image.
Displays the next image.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
i button
Playback button
Four-way controller
OK button
2
LCD monitor
Deleting a Displayed Image
While the image is displayed, press the i button
to display the Delete screen. Press the four-way
controller (2) to select Delete, and press OK. The
image is deleted.
100-0001
Delete
Cancel
Press the shutter release button halfway or fully to
prepare the camera to take another picture.
Exit OK OK
MENU
All images & sounds
file number is shown first.
• You can enlarge the image displayed on the LCD monitor by pressing
the zoom/f/ybutton.
Zoom Playback 1p.70
• For movie pictures, the first frame is displayed.
• If no images are stored, the “No Image & sound” message is
displayed.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
Using an SD Memory Card / MultiMediaCard
Images taken with the camera are recorded on the
SD Memory Card / MultiMediaCard. You can use
the camera to view the images recorded on the
card, transfer the images to your PC, and print them
out.
2
Viewing images on the camera
One advantage of a digital camera is that you can
check the picture as soon as you take it. You can
check the composition and brightness, and take a
picture again if you are not satisfied.
Playing Back Still Pictures1p.70
Viewing Images on a TV
Displaying your pictures on a TV is handy for those group occasions. To
view images on your TV, connect the camera to the TV with the AV
cable.
Viewing Images on a TV1p.81
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Images on a PC
You can view recorded images and edit them on the PC just by
connecting the camera to the PC with the USB cable and downloading
the images (you need to install the USB driver if you are using Windows
98). You can also remove the SD Memory Card / MultiMediaCard from
the camera and transfer the data with a card reader. On a laptop, you
can put a SD Memory Card / MultiMediaCard in a card adapter and insert
it into your card slot to transfer the image data. (When using other
equipment to transfer your images from your SD Memory Card /
MultiMediaCard, please read the operating manual for your equipment.)
2
1Reference [PC Connection Manual]
Printing Images at a Printing Service
Prints of images recorded on the SD Memory Card / MultiMediaCard can
be ordered in the same way as with conventional photographs by taking
the SD Memory Card / MultiMediaCard to a store that performs printing.
DPOF (Digital Print Order Format) settings allow you to specify the
number of copies or to include the date. Set these before taking your
card to a store providing DPOF printing.
Setting the Printing Service (DPOF) 1p.82
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Operations
Using the Button Functions
1
2
3
4
5
6, 7, 8
9
3
10
Capture Mode
The Button functions of Capture Mode are as follows, and this mode is
switched to Playback Mode by pressing Playback button.
1 Obutton
2 bbutton
Changes the flash mode. (1p.39)
3 )button
Changes the focus mode as follows. (1p.37)
Manual focus mode (1p.37)
4
5
6
7
8
9
Zoom button
Changes the size of the subject on the LCD monitor or viewfinder. (1p.59)
Playback button
Switches to Playback mode. (1p.36)
Four-way controller (45)
Changes the EV compensation. (1p.62)
Four-way controller (2)
Selects continuous shooting mode or self-timer mode. (1p.56, 55)
Four-way controller (3)
Displays the virtual mode dial and changes the capture mode. (
1p.36)
OK button
Selects a menu item.
10 MENU button
Displays [Rec.Mode] menu. (1p.32)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6, 7
8
9
3
Playback Mode
The Button functions of Playback Mode are as follows, and this mode is
switched to Capture Mode by pressing Playback button or the shutter
release button halfway.
1 Obutton
The voice memo can be set as a voice message. (1p.75)
2
3
4
Z button
i button
Deletes the image. (1p.77)
Zoom/f/ybutton
Press f in Normal Playback mode to display nine images at once.
(1p.71)
Display image displayed on the LCD monitor. (1p.70)
5
6
7
8
Playback button
Switches to Capture mode.
Four-way controller (45)
Plays back previous or next image. (1p.26)
Four-way controller (2)
Sets DPOF settings. (1p.82)
OK button
Saves the function selected by the menu item. (1p.32)
When pressed in Zoom Display or Nine-image Display mode, changes
to Normal Playback mode. (1p.70-71)
9
MENU button
Displays Playback menu. (1p.32)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Menu
Press the MENU button to display the menus on the LCD screen. With
these you can set functions, save the settings, and change the camera
settings.
How to Set the Menus
A button operation guide is displayed on the LCD monitor during menu
operation.
3
1
Press the MENU button.
The menu screen is displayed. The current selection is displayed in a
frame.
2
3
Press the four-way controller (45).
Use the four-way controller (45) to select the menu screen.
Press the four-way controller (23) to select an item.
Press the four-way controller (23) to moves the selection frame up
and down.
4
Press the four-way controller (45) to change the
setting.
Press the four-way controller (5) to move to a Select
screen if available.
When finished, press the OK button to return to the menu.
5
Press the OK button.
This saves the settings and returns to Capture or Playback mode.
• If you press any buttons except the OK button before press the OK
button and leave the menu screen, any changes to setting will not be
saved.
• Even after you press the OK button and close the menu screen, if the
camera is turned off improperly (such as removing the batteries while
the camera is on), your settings will not be saved.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Example of menu operation (Pressing the MENU button in
Capture mode)
1
MENU button
[A Rec.Mode] Menu
[QPlayback] Menu
[B Set-up] Menu
Rec. Mode
Playback
Set-up
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Playback Message
Digital Filter
Resize
Format
Sound
AWB
Data Adjust
World Time
Language/
01/01/2003
On
Multiple
Trimming
Alarm
Off
English
Exit OK OK
1/2
Exit OK OK
1/3
Exit OK OK
MENU
MENU
MENU
1/3
3
2
3
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
AWB
Multiple
Exit OK OK
MENU
1/3
4
Selection Screen
Rec. Mode
White Balance
AWB
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
AWB
Multiple
Exit OK OK
Exit OK OK
MENU
MENU
1/3
3
Rec. Mode
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
AWB
AWB
Multiple
Multiple
Exit OK OK
1/3
Exit OK OK
MENU
MENU
1/3
3
Next menu screen
• If you press the shutter release button halfway and move the camera
to Capture mode, any changes to the setting will not be saved.
• When you display the menu from Capture mode, the [A Rec.Mode]
menu will be displayed, and when you display the menu from Playback
mode, the [QPlayback] menu will be displayed.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu List
[A Rec.Mode] Menu
Item
Refere
nce
Description
Recorded Pixels
Quality level
White Balance
Focusing Area
AE Metering
Sensitivity
Selects the number of recorded pixels.
Selects the image compression rate.
Adjusts color balance according to lighting.
Changes the area for autofocus.
p.40
p.41
p.42
p.44
p.45
p.46
p.60
p.57
Sets the metering method to determine exposure.
Sets sensitivity.
3
Digital Zoom
Interval Shoot
Takes digital zoom pictures.
Takes pictures at a specified interval of time.
Sets the recorded pixels of the movie picture, color mode, and
Fast Fwd Movie.
Movie
p.63
Memory
Saves the Rec. Mode settings when the camera is turned off. p.68
Sharpness
Saturation
Contrast
Sets the sharpness.
Sets the saturation.
Sets the contrast.
p.47
p.48
p.49
[
Playback] Menu
Q
Refere
nce
Item
Description
Playback Message Records a voice message.
p.75
p.88
p.85
p.87
p.100
p.72
Digital Filter
Resize
Sets the digital filter.
Changs the image size.
Trimming
Alarm
Trims images.
Sets the alarm to ring at a specified time.
Plays recorded images successively.
Slideshow
34
Download from Www.Somanuals.com. All Manuals Search And Download.
[B Set-up] Menu
Refere
nce
Item
Description
Format
Sound
Formats the SD Memory Card / MultiMediaCard.
p.90
Sets the volume and type of button operation sound, start-up
sound, shutter sound, and self-timer sound.
p.91
Date Adjust
World Time
Language/
Display
Sets the date and time.
p.92
p.93
p.94
p.95
p.97
p.99
Sets world time.
Switches the language for displaying menus and messages.
Sets the display information.
Screen Setting
Video Out
Sets the start-up screen and background color.
Sets the video output format.
3
When this option is turned on, the Delete screen is displayed
with [Delete] or [All Images] selected.
Quick Delete
Quick Zoom
p.77
p.70
For playing back images at the maximum zoom size with the
Zoom button pressed only once.
Auto Power Off
Reset
Tturs off the power automatically.
Returns settings to defaults.
p.99
p.99
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking Pictures
Setting the Capture Functions
Changing the Mode
Capture mode is for taking pictures. Playback mode is for playing back
or erasing images and sound.
Switching Between Capture Mode and Playback Mode
• To change from Capture mode to Playback mode, press the Playback
button.
• To change from Playback mode to Capture mode, press the Playback
button or the shutter release button halfway.
4
Selecting the Capture Mode
Display the virtual mode dial to select the Capture mode. You can select
from 12 Capture modes.
The camera automatically sets the shutter
speed and aperture for taking still pictures.
Program
Landscape
Night-Scene Mode
e
H
/
Enhances your landscape photos.
Enables you to take dark scenes such as night
views.
Night-Scene Portrait Enables you to take portraits in dark conditions.
&
J
Portrait
Enhances your portrait photos.
Enhances pictures taken against dazzling
backgrounds such as beaches or snow.
Surf and Snow
Flower
L
I
p.50
Enhances your flower photos.
Beautiful results on pictures of sunsets or
sunrises.
Sunset
K
Fireworks
Enhances your fireworks photos.
Enhances your snap photos.
.
:
C
Snap Mode
Movie Picture Mode You can take movie pictures.
Panorama Assist
Mode
You can set up and take panorama photos.
F
1
Press the four-way controller (3) in
Capture Mode.
SNAP
The virtual mode dial is displayed.
OK OK
36
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
Press the four-way controller (45) to select your
desired display mode.
The selected icon is displayed in a frame.
Press the OK button.
The icon of the selected Capture mode is displayed and the camera is
ready to take pictures.
When the focus mode is set to manual, the four-way controller (23)
becomes the manual focus button and the virtual mode dial cannot be
displayed. Press ) to select the Autofocus mode or other mode,
then use the four-way controller (3) to change the mode.
)button
4
Changing Focus Settings
Focus Mode
Focuses on objects in the focusing area when the
shutter release button is pressed halfway. Use
when the distance to the subject is more than
30cm.
(No icon) Autofocus mode
Use when the distance to the subject is between
approximately 1cm~50cm (Wide) and 20cm~50cm
(Tele). Focuses on objects in the focusing area
when the shutter release button is pressed halfway.
q
Macro mode
s
Infinity-landscape mode Use for taking pictures of distant objects.
Manual focus mode Adjust focus manually.
z
1
Pressing )in Capture mode will switch focus
modes, and the current setting is displayed on the LCD
monitor.
The camera is ready to take a picture in the set focus mode.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
• The focus mode default setting is the Autofocus mode.
• In Movie Picture mode (1p.63), only the fixed focus is available.
• If you use the flash in Macro mode, the image may be overexposed or
a dark area may appear at the bottom right of the picture.
If you take a picture while looking through the viewfinder when the focus
mode is set to Macro mode, the range of the resulting picture will differ
from what was seen in the viewfinder. Be sure to check the image on the
LCD monitor.
Manual Focus
On the zsetting, press the four-way controller (23) to enlarge the
central portion of the screen to full screen on the LCD monitor.
Adjust the focus with the four-way controller while watching the image on
the monitor.
4
For distant focus
For closer focus
Once the focus is set, press any button other than the four-way controller
(23), or take your finger off of the four-way controller for about 2
seconds. The camera will switch to the standard Capture screen.
• When focusing, hold down the four-way controller (23) to focus
quickly.
• Enlarged display is not available near maximum magnification in
digital zoom.
Saving the Focus Mode 1p.68
38
Download from Www.Somanuals.com. All Manuals Search And Download.
bbutton
Selecting the Flash Mode
The flash discharges automatically based on light
conditions.
(No icon) Auto
4
The flash never discharges regardless of light
conditions.
Flash Off
a
b
The flash always discharges regardless of light
conditions.
Flash On
Reduces red-eye in the picture, caused by the flash
reflecting from the subject’s eyes. The flash
discharges automatically.
Auto flash + red-eye
reduction
c
d
Reduces red-eye in the picture, caused by the flash
reflecting from the subject’s eyes.
The flash discharges regardless of lighting conditions.
Flash On + red-eye
reduction
• The flash is always off when the Capture mode is set to C,
Continuous shooting, Infinity-Landscape, or Fireworks.
• When using the flash, it always discharges once before taking the
picture, to assist with metering.
• In Auto + red-eye reduction or Flash On + red-eye reduction, the flash
discharges once before taking the picture to make the iris of the
subject’s eyes contract, shortly before firing again to take the picture.
• The shutter speed will be slower with the flash off, or in low light
conditions such as a night scene. Use a tripod to prevent camera
movement.
1
Press the bbutton in Capture mode.
This will switch flash modes, and the current icon will be displayed on
the LCD monitor.
The camera is ready to take a picture in the selected flash mode.
Status of the Flash Status Lamp 1p.25
Saving the Flash Mode 1p.68
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Four-way
controller
OK button
AWB
Multiple
Exit OK OK
MENU
1/3
MENU button
e
F
Selecting the Recorded Pixels
Select the number of recorded pixels from 2048×1536, 1600×1200,
1024×768, 640×480.
4
The more pixels there are, the larger the image size and file size.
The image file size will also differ according to quality level settings.
2048×1536
1600×1200
1024×7680
640×480
Suited for printing on A4 paper.
Suited for printing on A5 paper.
Suited for printing on postcard-size paper.
Suited for attaching to e-mail or for creating websites.
1
Press the MENU button in Capture mode.
The [ Rec. Mode] menu will be displayed.
A
2
3
Select [Recorded Pixels] on the [ Rec. Mode] menu.
A
Press the four-way controller (45)
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
to change the recorded pixels.
AWB
4
Press the OK button.
The camera is ready to take a picture.
Multiple
MENU
1/3
Exit OK OK
• In movie picture mode, select from 320×240 or 160×120. 1p.65
• Selecting a large number of recorded pixels will result in a clearer
image when printed.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Four-way
controller
OK button
AWB
Multiple
Exit OK OK
MENU
1/3
MENU button
e
F
Selecting the Quality Level
4
Select the image compression rate.
The more E there are, the better the quality and the larger the file.
The image file size will also differ according to Recorded Pixels settings.
This has the lowest compression rate, and is suited for
printing large pictures on A4 paper.
Best
C
D
E
This has a standard compression rate, and is suited for
viewing as standard photographs or on your computer
screen.
Better
Good
Highest compression rate. Suited for attaching to e-mail or
for creating websites.
1
Press the MENU button in Capture mode.
The [ Rec. Mode] menu will be displayed.
A
2
3
Select [Quality Level] on the [ Rec. Mode] menu.
A
Press the four-way controller (45)
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
to change the quality level.
AWB
4
Press the OK button.
The camera is ready to take the picture.
Multiple
MENU
1/3
Exit OK OK
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Four-way
controller
OK button
AWB
Multiple
Exit OK OK
MENU
1/3
MENU button
e
F
Adjusting the White Balance
4
Adjusts for natural coloring in your picture, according to the lighting.
F
Auto
The camera makes the adjustment automatically.
For taking pictures outside in sunlight.
Daylight
Shade
G
For taking pictures outside in the shade.
H
For taking pictures under standard light bulbs or other
tungsten light.
Tungsten Light
I
J
K
Fluorescent
Light
For taking pictures under fluorescent light.
For taking pictures by manually adjusting the white
balance.
Manual
1
Press the MENU button in Capture mode.
The [ Rec. Mode] menu will be displayed.
A
2
3
Select [White Balance] on the [ Rec. Mode] menu.
A
Press the four-way controller (5).
White Balance
AWB
The White Balance selection screen is
displayed.
4
5
Press the four-way controller (23)
to change the setting.
Exit OK OK
MENU
Press the OK button twice.
The camera is ready to take the picture.
Saving the White Balance 1p.68
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Manually
1
Select [ ] (Manual) on the White
K
Balance selection screen.
White Balance
AWB
2
3
Point your camera at white paper to
fill the screen.
Exit OK Adjust
MENU
Press the OK button.
The LCD monitor will display “Adjusting”, and return to the menu
screen when the white balance is adjusted.
4
Press the OK button.
The camera is ready to take a picture.
4
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Four-way
controller
OK button
AWB
Multiple
Exit OK OK
MENU
1/3
MENU button
e
F
Setting the Focusing Area
4
You can change the area for autofocus (Focusing Area).
Multiple Normal range
Spot
The autofocus range becomes smaller.
1
Press the MENU button in Capture mode.
The [ Rec. Mode] menu will be displayed.
A
2
3
Select [Focusing Area] on the [ Rec. Mode] menu.
A
Press the four-way controller (45)
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
to change the focusing area.
AWB
4
Press the OK button.
The camera is ready to take the picture.
Multiple
MENU
1/3
Exit OK OK
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Four-way
controller
OK button
AWB
Multiple
Exit OK OK
MENU
1/3
MENU button
e
F
Setting the Light Metering Range
4
You can choose the part of the screen to use for measuring brightness
and determining exposure.
Detailed measurement of entire screen to determine
exposure.
Multi-segment
Center-weighted
Spot
L
M
N
Measures mainly the center of the screen to determine
exposure.
Measures only the very center of the screen to
determine exposure.
1
Press the MENU button in Capture mode.
The [ Rec. Mode] menu will be displayed.
A
2
3
Select [AE Metering] on the [ Rec. Mode] menu.
A
Press the four-way controller (45)
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
to change the metering mode.
AWB
4
Press the OK button.
The camera is ready to take the picture.
Multiple
MENU
1/3
Exit OK OK
Saving the AE Metering Method 1p.68
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Four-way
controller
OK button
AWB
Multiple
Exit OK OK
MENU
1/3
MENU button
e
F
Setting Sensitivity
4
You can set the Sensitivity to match the brightness of the surroundings.
Auto
50
The camera makes the adjustment automatically.
• The lower the Sensitivity (smaller number), the smaller the noise and
sharper the image. The shutter speed will be slower in low light
conditions.
• The higher the Sensitivity (larger number), the faster the shutter speed
in low light conditions. The image will have more noise.
100
200
400
1
Press the MENU button in Capture mode.
The [ Rec. Mode] menu will be displayed.
A
2
3
Select [Sensitivity] on the [ Rec. Mode] menu.
A
Press the four-way controller (45)
Rec. Mode
Sensitivity
Auto
On
to change the sensitivity.
Digital Zoom
Interval Shoot
4
Press the OK button.
The camera is ready to take the picture.
Movie
Memory
Exit OK OK
MENU
2/3
The only available AUTO settings are 50, 100, and 200.
Saving the Sensitivity 1p.68
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Four-way
controller
AWB
Multiple
OK button
Exit OK OK
MENU
1/3
MENU button
e
F
Setting Image Sharpness
4
You can make the image outlines sharp or soft.
1
Press the MENU button in Capture mode.
The [ Rec. Mode] menu will be displayed.
A
2
3
Select [Sharpness] on the [ Rec. Mode] menu.
A
Press the four-way controller (45)
Rec. Mode
Sharpness
to select x (Normal), z (Hard), or
Saturation
y (Soft).
Contrast
4
Press the OK button.
The camera is ready to take the picture.
Exit OK OK
MENU
3/3
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Four-way
controller
OK button
AWB
Multiple
Exit OK OK
MENU
1/3
MENU button
e
F
Setting Color Saturation
4
This sets the color saturation.
1
Press the MENU button in Capture mode.
The [ Rec. Mode] menu will be displayed.
A
2
3
Select [Saturation] on the [ Rec. Mode] menu.
A
Press the four-way controller (45)
Rec. Mode
Sharpness
to select x (Normal), z (High), or
Saturation
y (Low).
Contrast
4
Press the OK button.
The camera is ready to take the picture.
Exit OK OK
MENU
3/3
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Rec. Mode
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Four-way
controller
AWB
Multiple
OK button
Exit OK OK
MENU
1/3
MENU button
e
F
Setting the Image Contrast
4
You can set the image contrast level.
1
Press the MENU button in Capture mode.
The [ Rec. Mode] menu will be displayed.
A
2
3
Select [Contrast] on the [ Rec. Mode] menu.
A
Press the four-way controller (45)
Rec. Mode
Sharpness
to select x (Normal), z (High), or
Saturation
y (Low).
Contrast
4
Press the OK button.
The camera is ready to take the picture.
Exit OK OK
MENU
3/3
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Taking Pictures
Shutter release button
Four-way controller
OK button
4
Program Mode
In Program Mode (e), you can set all the functions and take pictures.
1
2
3
4
5
Press the four-way controller (3) in Capture Mode.
The virtual mode dial is displayed.
Press the four-way controller (45)
to select [e].
SNAP
Press the OK button.
The camera is ready to take the picture.
OK OK
Set the functions you want to use.
See “Setting the Capture Functions” (p.36-p.49) for instructions.
Press the shutter release button.
The picture is taken.
Taking Still Pictures 1p.24
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Shutter release button
Four-way controller
OK button
Picture Mode
You can match your settings to the situation.
4
Picture Mode
There are nine modes available.
Landscape
Enhances your landscape photos.
H
/
Night-Scene Mode Enables you to take dark scenes such as night views.
Night-Scene
Enables you to take portraits in dark conditions.
Portrait
&
J
Portrait
Enhances your portrait photos.
Enhances pictures taken against dazzling
backgrounds such as beaches or snow.
Surf and Snow
L
Flower
Enhances your flower photos.
I
K
.
Sunset
Beautiful results on pictures of sunsets or sunrises.
Enhances your fireworks photos.
Enhances your snap photos.
Fireworks
Snap Mode
:
51
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Press the four-way controller (3) in Capture Mode.
The virtual mode dial is displayed.
Press the four-way controller (45)
to select your desired display mode.
SNAP
OK OK
3
4
Press the OK button.
The Picture mode is selected.
Press the shutter release button.
The picture is taken.
4
In Picture mode, the EV compensation, saturation, contrast, sharpness,
and white balance are automatically set to the optimum values for each
mode. (You can change the settings.)
To avoid camera movement in Night-scene, Night-scene Portrait,
Sunset, or Fireworks mode, you are recommended to fix the camera on
a tripod.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Shutter release button
Four-way controller
OK button
Taking Panorama Pictures (Panorama Assist
Mode)
4
Using the included software (ACDSee™), you can easily join several
images to form one panorama picture. Overlap and stitch the edges of
images taken in Panorama Assist mode and create a panorama image.
1
2
Press the four-way controller (3) in Capture Mode.
The virtual mode dial is displayed.
Press the four-way controller (45) to select [
F
(Panorama Assist)].
3
4
Press the OK button.
Press the four-way controller to set
the shift direction.
4 joins the images at the left.
Set shift direction
5 joins the images at the right.
2 joins the images at the top.
3 joins the images at the bottom.
The explanation described below indicates that 5 is set.
5
Take the first image.
100
Press the shutter release button to take the first
image. The right edge of the image is displayed
in half transparent form at the left of the LCD
10/10//2003
11:20
monitor.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
Take the second image.
Move the camera to the right until the real
image approx. coincides with the half
transparent one, and then press the shutter
release button for taking the second image.
Repeat the same procedure for taking the third
image and following pictures.
Press the four-way controller (3).
The virtual mode dial is displayed, and switch to another Capture
mode to cease this Panorama mode.
• It is impossible to create a panorama picture by joining images using
the camera itself. Use the panorama software, ACDSee, packed
together with the camera. For details on joining panorama images, see
the separate booklet PC Connection Manual.
4
• Continuous shooting and interval shooting are not possible in
Panorama assist mode.
• You need a Windows PC for joining panorama pictures. (The provided
software is not Macintosh-compatible.)
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Shutter release button
Four-way controller
e
CF
Using the Self-Timer
4
The picture will be taken 10 seconds after the shutter release button is
pressed.
1
2
Press the four-way controller (2) to
display gon the LCD monitor.
100
Press the shutter release button.
The self-timer is engaged and the self-timer
lamp lights. The picture is taken about 3
seconds after the self-timer lamp begins to
blink.
10/10//2003
11:20
the LCD monitor.
• Pressing the four-way controller or the MENU button during the
countdown display will cancel the self-timer.
Playing Back Still Pictures1p.26
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Shutter release button
Four-way controller
e
Continuous Shooting (Continuous Shooting/
Multi Continuous Shooting)
4
Pictures are taken continually while the shutter release button is pressed.
There are Continuous Shooting and Multi Continuous Shooting as follows.
Continuous
Images are captured, processed, and saved one by one.
aj
a_
Shooting
Multi Continuous Pictures are taken four frames at a time and saved as a
Shooting single image.
1
2
Press the four-way controller (2) to
display ajor a_on the LCD
monitor.
100
Press the shutter release button.
Pictures are taken continually while the shutter
release button is pressed.
10/10//2003
11:20
Recording stops when you release the shutter release button.
Playing Back Still Pictures1p.26
• You can continue shooting until the SD Memory Card /
MultiMediaCard is full.
• The interval between continuous shots differs according to recorded
pixels and quality level settings.
• The flash will not fire in Continuous Shooting or Multi Continuous
Shooting mode.
• Continuous Shooting and Multi Continuous Shooting cannot be used
in Movie Picture, Panorama Assist, Night-Scene, Night-Scene Portrait,
or Fireworks mode.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Four-way controller
OK button
MENU button
e
Taking Pictures at Fixed Intervals (Interval Shoot)
4
In this mode, still pictures are taken automatically at a fixed interval.
1
2
Press the four-way controller (2) to display kon the
LCD monitor.
Press the shutter release button.
Interval shooting will start with the following settings.
•Interval
•Number of Shot
•Start Time
00min10sec
02
00hr00min
When shooting is finished, the camera turns off automatically.
Setting the interval, number of shot, and start time
1
Press the MENU button in Capture mode.
The [A Rec. Mode] menu will be displayed.
2
3
Select [Interval Shoot] on the [ Rec. Mode] menu.
A
Press the four-way controller (5).
Interval Shoot
Interval
0min10sec
The Interval Shooting menu will be displayed
and [Interval] will be selected.
Mumber of Shot
Start Time
02
0hr 00min
Exit OK OK
MENU
57
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Set the interval time.
1. Press the four-way controller (5).
23 are displayed above and below the number of minutes.
2. Use the four-way controller (23) to change the number of
minutes, then press the four-way controller (5).
23 are displayed above and below the number of seconds.
3. Use the four-way controller (23) to change the number of
seconds, then press the four-way controller (5).
4. Press the four-way controller (3).
The frame will move to [Number of shot].
5
6
Use the four-way controller (45) to change the number
of pictures, then press the four-way controller (3).
The frame will move to [Start Time].
Set the time to start shooting.
1. Press the four-way controller (5).
4
23 are displayed above and below the number of hours.
2. Use the four-way controller (23) to change the number of hours,
then press the four-way controller (5).
23 are displayed above and below the number of minutes.
3. Use the four-way controller (23) to change the number of
minutes, then press the four-way controller (5).
7
Press the OK button 2 times.
Playing Back Still Pictures1p.26
• Interval shooting can be set at intervals of 10 seconds to 4 minutes in
units of 1 second, and intervals of 4 minutes to 99 minutes in units of
1 minute. Intervals of less than 10 seconds cannot be set.
• The number of pictures can be set in the range of 2 to 99 pictures.
• The start time can be set between 0 minutes and 23 hours 59 minutes
in units of 1 minute.
• If the start time is set to 0 minutes, the first picture will be taken as soon
as the shutter release button is pressed.
• If you press the power switch on during standby, the remaining number
of pictures and interval time will be displayed on the LCD monitor. If
you press the MENU button, the message “Stop interval shooting?”
will be displayed. To cancel interval shooting, press the OK button.
• If the SD Memory Card / MultiMediaCard runs out of memory, interval
shooting stops and the camera turns off automatically.
Interval shooting is not possible in Movie Picture or Panorama Assist mode.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Zoom button
Four-way controller
OK button
MENU button
e
F
Using the Zoom
4
You can use the Zoom to take pictures in Tele or Wide mode.
1
Press the Zoom button in Capture
mode.
100
x Tele: Subject becomes larger.
wWide: Subject becomes smaller.
When the digital zoom function is disabled, the
optical zoom can be used to enlarge the subject
up to 2.8 times.
Zoom bar
When the digital zoom function is enabled, you can further enlarge the
subject up to 11.2 times.
100
Digital zoom range
Saving the Zoom Position 1p.68
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Enabling the Digital Zoom Function
1
Press the MENU button in Capture mode.
The [A Rec. Mode] menu will be displayed.
Press the four-way controller (3) to
2
3
4
Rec. Mode
Sensitivity
Digital Zoom
Interval Shoot
Movie
Auto
On
select [Digital Zoom].
Press the four-way controller (5) to
select On.
Memory
Exit OK OK
MENU
2/3
Press the OK button.
The camera is ready to take the picture.
4
Saving the Digital Zoom Function Setting 1p.68
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Voice button
Shutter release button
Recording Sound (Voice Recording Mode)
This mode is for recording sound. The recordable time is displayed on
the LCD monitor according to how much memory is available on the SD
Memory Card / MultiMediaCard.
4
1
1
Press the Obutton in Capture mode.
The recordable time is displayed on the LCD
monitor.
10:16
00:00
1. Remaining time 2. Recording time
SHUTTER
REC
Start
2
10/10//2003
11:20
2
3
Press the shutter release button.
Recording starts. Oflashes during recording.
Press the shutter release button.
Recording stops. The remaining available recording time is displayed.
Playing Back Sound 1p.76
Sound is saved as a monaural WAVE file (PCM method).
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Four-way controller
e
CF
EV Compensation
4
Use EV Compensation when you want to intentionally over expose
(brighten) or under expose (darken) your picture.
1
Press the four-way controller (45)
in Capture Mode.
100
5Adjusts the exposure to over-expose (+
side), 4Adjusts the exposure to under-expose
(- side).
10/10//2003
11:20
+2.0
The EV Compensation setting is displayed on the LCD monitor.
When you press the four-way controller (45) once, or when you set the
setting to ±0, the display will disappear in two seconds.
Saving the EV Compensation Setting 1p.68
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Shutter release button
Four-way controller
OK button
You can take movie pictures. The recording time for a single movie is
displayed at the top right of the LCD monitor. Sound can be recorded at
the same time.
4
You can select either 320×240 or 160×120 for recorded pixels in movie
picture mode 1p.65
1
2
3
Press the four-way controller (3) in Capture Mode.
The virtual mode dial is displayed.
Press the four-way controller (45)
SNAP
to select [C(Movie)].
Press the OK button.
OK OK
1 Flash OFF icon
2 Movie Picture mode icon
3
3 Recording time
1
2
337sec
10/10//2003
11:20
4
Press the shutter release button.
Recording will begin.
You can switch the image size using the Zoom button.
x
w
Subject becomes bigger.
Subject becomes smaller.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press the shutter release button.
Recording will end. The remaining available recording time is displayed.
Recording by holding down the shutter release button
If you hold down the shutter release button for one second or more, the
camera will record while you hold down the button. Recording stops
when you release the shutter release button.
Playing Back Movie Pictures 1p.73
• The flash will not fire in Movie Picture mode.
• Continuous shooting and interval shooting are not possible in Movie
Picture mode.
• The focus is fixed in movie picture mode.
• When shooting in Movie Picture mode, only the digital zoom can be
operated.
4
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Four-way controller
OK button
MENU button
C
Changing the Recorded Pixels Setting When
Taking Movie Pictures
4
In movie picture mode, you can select either 320×240 or 160×120 for the
number of recorded pixels (resolution).
The more pixels there are, the larger the image size but the smaller the
recording time.
1
Press the MENU button in Capture mode.
The [A Rec. Mode] menu will be displayed.
2
3
Select [Movie] on the [ Rec. Mode] menu.
A
Press the four-way controller (5).
The movie setup screen will be displayed.
4
Press the four-way controller (45)
to change the recorded pixels.
Movie
Recorded Pixels
320 240
Full Color
Off
Color Mode
Fast Fwd Movie
Exit OK OK
MENU
5
Press the OK button 2 times.
The camera is ready to record a movie.
Taking Movie Pictures 1p.63
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Four-way controller
OK button
MENU button
C
Changing the Color Mode Setting When Taking
Movie Pictures
4
You can record a movie picture in one of three color mode settings: full-
color, black-and-white, or sepia.
1
Press the MENU button in Capture mode.
The [A Rec. Mode] menu will be displayed.
2
3
Select [Movie] on the [ Rec. Mode] menu.
A
Press the four-way controller (5).
The movie setup screen will be displayed.
4
Select [Color Mode] with the four-
way controller (3).
Movie
Recorded Pixels
320 240
Full Color
Off
Color Mode
Fast Fwd Movie
Exit OK OK
MENU
5
6
Press the four-way controller (45) to change the color
mode.
Press the OK button 2 times.
The camera is ready to record a movie.
Taking Movie Pictures 1p.63
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Four-way controller
OK button
MENU button
C
T
aking Fast Forward Movie Pictures (Fast Fwd Movie)
This mode lets you take movie pictures at a delayed frame rate so that
when you play the movie back, the action appears speeded up.
4
1
Press the MENU button in Capture mode.
The [A Rec. Mode] menu will be displayed.
2
3
Select [Movie] on the [ Rec. Mode] menu.
A
Press the four-way controller (5).
The movie setup screen will be displayed.
4
5
Press the four-way controller (3) to select [Fast Fwd
Movie].
Press the four-way controller (45)
Movie
Recorded Pixels
Color Mode
320 240
Full Color
Off
to select [Off (x1)], [x2], [x5], [x10],
[x20], [x50], or [x100].
Fast Fwd Movie
Exit OK OK
MENU
6
Press the OK button 2 times.
Taking Movie Pictures 1p.63
• Off (x1) is the normal movie picture setting (15 frames per second).
When x2 or x5 is selected, the number of frames recorded per second
decreases by 1/2 or 1/5, respectively.
• As movie pictures are normally played back at the rate of 15 frames
per second, movies taken at x2 are played back twice as fast and
movies taken at x5 are played back five times as fast.
• Sound cannot be recorded.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Saving the Settings
Saving the Menu Items (Memory)
You can choose whether to save the set values when the camera is
turned off. If you select On, the camera saves the settings in effect just
before the camera is turned off. If you select Off, the settings return to
default settings when the camera is turned off.
Default
Setting
Item
Description
Saves the Flash mode setting selected with the
button.
Flash
White Balance
O
Saves the White Balance settings on the Rec. Mode
menu.
P
P
4
EV compensation Saves the EV compensation settings.
Saves the Digital Zoom settings on the Rec. Mode
menu.
Digital Zoom
AE Metering
Sensitivity
O
Saves the AE Metering settings on the Rec. Mode
menu.
P
P
Saves the Sensitivity settings on the Rec. Mode
menu.
Focus Mode
Zoom Position
MF Position
Saves the Focus Mode settings.
P
P
P
Saves the Zoom Position settings.
The focus position set by Manual Focus is saved.
Saves the file numbers. File numbers will continue to
have sequential numbers even after changing the SD
Memory Card / MultiMediaCard.
File No.
O
• Menu items not included in Memory will also be saved with the settings
selected on the menus for each function.
• Zoom positions set within the digital zoom range will not be saved even
when Zoom Position is set to On in Memory.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Press the MENU button in Capture mode.
Press the four-way controller (23)
Rec. Mode
Sensitivity
Digital Zoom
Interval Shoot
Movie
Auto
On
to select [Memory].
3
Press the four-way controller (5).
The Memory menu will be displayed.
Memory
Exit OK OK
MENU
2/3
4
5
6
Press the four-way controller (23)
to select the item.
Memory
Flash
White Balance
EV Compensation
Digital Zoom
AE Metering
Press the four-way controller (45)
to select O (On) or P (Off).
Exit OK OK
MENU
1/2
Press the OK button 2 times.
The camera is ready to take a picture.
4
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback/Deleting
Playing Back Images
Zoom/f/ybutton
Four-way controller
Playing Back Still Pictures
See “Playing Back Images” (p.26) and “Playing Back Previous or Next Images” (p.26).
Zoom Display
5
You can display images magnified up to 8 times. A guide to operation is
displayed on the LCD monitor during magnification.
1
Enter the Playback mode and choose the image you
want to magnify with the four-way controller (45).
2
Press
x/yon the Zoom/f/ybutton.
1.5x
The image will be magnified (1 to 8 times).
Continue to press to magnify the image even
greater.
• The following operations can be performed
while the magnified image is displayed.
Four-way controller (2345)
Zoom/f/ybutton (x)
Zoom/f/ybutton (w)
OK button
Moves the position to be magnified.
Makes the image larger.
Makes the image smaller.
Turns the guide marks on/off.
3
Press the OK button.
Zoom playback will end.
If you set [Quick Zoom] in the [B Set-up] menu to ON, the image will be
magnified eight times when (x/y) is pressed in step 2.
Movie pictures cannot be magnified.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Zoom/f/ybutton
Four-way controller
Nine-image Display
You can display nine images at the same time.
1
2
Enter the Playback mode and choose the image you
want to place in the center with the four-way controller
(45).
5
Press w/f on the Zoom/f/y
button.
Nine images will be displayed with the selected
image in the center.
Choose an image with the four-way controller
(2345). When ten or more images have
been recorded, if you press the four-way
Selection screen
controller (5) while the bottom right image is
selected, the next nine images will be
displayed, and if you press the four-way controller (4) while the top left
image is selected, the previous nine images will be displayed.
Similarly, if you press the four-way controller (2) while an image on
the top row is selected, the previous nine images will be displayed, and
if you press the four-way controller (3) while an image on the bottom
row is selected, the next nine images will be displayed.
3
Press the OK button.
The screen will return to single-image display of the selected image.
In the case of movie pictures, the first frame will be displayed.
Sound files are displayed with O.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Four-way controller
OK button
MENU button
Using Slideshow for Continuous Playback
You can continuously play back all the images on the SD Memory Card
/ MultiMediaCard.
1
Enter the Playback mode and choose the image with
which to start the slideshow with the four-way
controller (45).
5
2
3
4
Press the MENU button.
The [Playback] menu will be displayed.
Playback
Slideshow
3sec
Select [Slideshow] with the four-way
controller (3).
2/2
Exit OK OK
MENU
Use the four-way controller (45) to
change the playback interval.
Choose from the following: 3 sec, 5 sec, 10 sec, 20 sec, or 30 sec.
5
Press the OK button.
Playback will start at the set interval.
• If you press the four-way controller or any buttons, such as the MENU
button, during continuous playback, the slideshow will stop.
• The slideshow will continue until you press any button.
• Movie pictures and pictures with a voice memo will be played through
to the end before the next picture is played back, regardless of the set
playback interval.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Obutton
Playback button
Four-way controller
Playing Back Movie Pictures
You can play back movie pictures. A guide to operation is displayed on
the LCD monitor during playback. The sound is played back at the same
time.
1
2
Enter the Playback mode and choose the movie picture
you want to play with the four-way controller (45).
5
Press the four-way controller (2).
Set Msg
100-0001
Playback will start.
• The following operations can be performed
during playback.
10/10//2003
11:20
Four-way controller (4)
Four-way controller (5)
Four-way controller (2)
Zoom/f/ybutton (x)
Reverse playback
Forward playback
Pauses playback.
Increases the volume.
Zoom/f/ybutton (w) Decreases the volume.
• The following operations can be performed while Pause is engaged.
Four-way controller (4)
Four-way controller (5)
Four-way controller (2)
Single frame reverse playback
Single frame forward playback
Cancels Pause. (Playback resumes.)
3
4
Press the four-way controller (3).
Playback will stop.
Press the Playback button.
The camera will return to the Capture mode.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding a Voice Memo
You can add a voice memo to a recorded image.
1
Enter the playback mode and choose
the image to which you want to add a
voice memo with the four-way
controller (45).
Start
100-0001
10/10//2003
11:20
If the image has no voice memo, the screen for
recording a voice memo is displayed on the
LCD monitor.
2
3
4
5
Press the Obutton.
Recording starts.
Press the Obutton.
Recording stops.
5
Press the four-way controller (3).
The recorded voice memo will be played back.
Press the four-way controller (3).
Playback stops.
• A voice memo cannot be added to protected (Z) images.
• Images with a voice memo are indicated with U on the LCD monitor.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a Voice Message
A voice memo added to an image can be set as a voice message.
The Obutton flashes during voice message recording, indicating that
there is a voice message.
1
Press the MENU button in Playback
mode.
Start
100-0001
The Playback Mode menu is displayed.
2
3
4
5
Select [Playback Message] from the
Playback Mode menu.
10/10//2003
11:20
Press the four-way controller (5).
The Voice Message Recording screen will be displayed.
Press the four-way controller (45) to select the image
to be used for the voice message.
5
Press the OK button.
The camera turns off, and the voice message is set.
Adding a Voice Memo1p.74
Playing Back a Voice Message
You can play back a voice message.
1
Press the Obutton.
The image will be displayed and the voice memo will be played back.
• Turn the camera on during voice message settings to perform regular
operations. Turn the camera off again to return to voice message
recording.
• To switch from voice message recording to Capture mode, turn the
camera off and then turn it on again.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback button
Four-way controller
Playing Back Sound
You can play back the recording you made in Voice Recording mode.
1
2
Enter the Playback mode and choose the recording you
want to play with the four-way controller (45).
Press the four-way controller (2).
Playback time
5
Playback will start.
100-0001
00:00:00
00:00:00
10/10//2003
11:20
Recording time
• The following operations can be performed
during playback.
Four-way controller (4)
Four-way controller (5)
Zoom/f/ybutton (x)
Rewinds and plays back the recorded
sound.
Advances and plays back the recorded
sound.
Increases the volume.
Zoom/f/ybutton (w) Decreases the volume.
3
4
Press the four-way controller (3).
Playback will stop.
Press the Playback button.
The camera will return to the Capture mode.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting Images
i button
Four-way controller
OK button
Deleting an Image
5
1
2
3
4
Enter the Playback mode and choose the image you
want to delete with the four-way controller (45).
Press the i button.
100-0001
The Delete screen will be displayed.
Select [Delete] with the four-way
controller (2).
Delete
Cancel
MENU
All images & sounds
Exit OK OK
Press the OK button.
• You can also delete images during Instant Review (p.25).
• You cannot delete protected (Z) images.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting a Voice Memo
If an image has a voice memo (indicated with U), you can delete the
voice memo without deleting the image.
1
Enter the Playback mode and choose the image with
the voice memo that you want to delete with the four-
way controller (45).
2
3
4
Press the i button.
The Sound Delete screen will be displayed.
100-0001
Sound Delete
Select [Sound Delete] with the four-
way controller (2).
Delete
Cancel
MENU
All images && sounds
Exit OK OK
Press the OK button.
Select [Delete] in step 3 above to delete both the image and the voice
memo.
5
78
Download from Www.Somanuals.com. All Manuals Search And Download.
i button
Four-way controller
OK button
Deleting All Images
You can delete all the images/sound at once.
• Once deleted, images/sounds cannot be restored.
• You cannot delete protected images/sounds.
1
Enter the Playback mode and press
the i button twice.
100-0001
Delete all images & sounds
5
on the memory card?
The Delete All Images/Sound screen will be
displayed.
Delete All
Cancel
Exit OK OK
MENU
2
3
Select [Delete All] with the four-way
controller (2).
Press the OK button.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Z button
Four-way controller
OK button
Protecting Images from Deletion (Protect)
You can protect images/sounds from being accidentally deleted.
1
Enter the Playback mode and choose the image or
sound you want to protect with the four-way controller
(45).
2
3
4
Press the Z button.
The Protect screen will be displayed.
100-0001
5
Select [Protect] with the four-way
controller (2).
Press the OK button.
Protect
Unprotect
MENU
All images & sounds
Exit OK OK
• Select [Unprotect] in step 3 above to cancel the Protect setting.
• Z is displayed during playback of protected images and sounds.
Protect All Images/Sounds
You can protect all images/sounds from being accidentally deleted.
1
2
Enter the Playback mode.
Press the Z button twice.
The Protect All Images & Sounds screen will be displayed.
3
4
Select [Protect] with the four-way controller (2).
Press the OK button.
Select [Unprotect] in step 3 above to cancel the Protect setting on all of
the images/sounds.
Even protected images/sounds will be deleted when formatting the SD
Memory Card / MultiMediaCard.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing Images on a TV
By using the AV cable, you can capture and play back images on a
TV or other equipment with a video IN jack. Make sure that both the
TV and the camera are turned off before connecting the cable.
5
1
2
Open the terminal cover and connect the AV cable.
Connect the sound terminal (white) and image terminal
(yellow) of the AV cable to the sound terminal (white)
and image input terminal (yellow) of the TV.
3
Turn the TV and camera on.
Selecting the Video Output Format 1p.99
The LCD monitor is always turned off when the camera is connected to
a TV. If you intend to use the camera for a long time, use of the AC
adapter (optional) is recommended. Refer to the operating manual for
the TV or equipment to which the camera is connected.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Printing Service (DPOF)
You can print the images on the SD Memory Card / MultiMediaCard
using a DPOF (Digital Print Order Format) compatible printer or at a
printing service.
Four-way controller
OK button
5
Printing Individual Image
Set the following items for each image.
Number of prints: Set the number of prints. You can select to print up to 99 copies.
Specify whether you want the date imprinted on the print or not.
1
2
Enter the Playback mode and use the four-way
controller (45) to select the image for which you want
to make DPOF settings.
Press the four-way controller (2).
100-0001
The DPOF screen will be displayed.
Copies
Date
01
Exit OK OK
DPOF
MENU
All Images
3
Use the four-way controller (45) to
select the number of prints, then
press the four-way controller (3).
The frame will move to [Date].
100-0001
Copies
Date
01
Exit OK OK
MENU
82
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
Use the four-way controller (45) to select either O
(On) or P (Off) for imprinting the date.
O:
P:
The date will be imprinted.
The date will not be imprinted.
Press the OK button.
Prints can be made according to the settings.
• If DPOF settings have already been made for an image, the previously
set number of prints and On/Off date setting will be displayed.
• To cancel DPOF settings, set the number of prints to 00 and press the
OK button.
• DPOF settings cannot be used with movie pictures.
• Depending on the printer or printing equipment at the photo
processing lab, the date may not be imprinted on the pictures even if
the DPOF setting was made.
5
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Four-way controller
OK button
Printing All Images
1
Enter the playback mode and press the four-way
controller (2).
The DPOF screen will be displayed.
2
3
Press the four-way controller (2).
The DPOF [All Images] screen will be displayed.
5
Use the four-way controller (45) to
select the number of prints.
100-0001
DPOF setting for all images
You can select to print up to 99 copies.
Press the four-way controller (3).
Use the four-way controller (45) to
Copies
Date
01
Exit OK OK
4
5
MENU
select either O(On) or P(Off) for imprinting the date.
O: The date will be imprinted.
P: The date will not be imprinted.
6
Press the OK button.
Prints can be made according to the settings.
• When the setting to print all images is made, the settings to print
individual images will be canceled.
• When you specify the number of prints in the DPOF setting, the
number applies to all the images. Before printing, check that the
number of prints is correct.
• DPOF settings cannot be used with movie pictures.
• To cancel DPOF settings, set the number of prints to 00 for the setting
for all the images.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing/Settings
Editing Images
Four-way controller
OK button
MENU button
Changing the Image Size
By changing the size and quality of a selected image, you can make the
file smaller than the original. After changing the size, the image can be
saved as a new image or written over the original image.
1
2
Press the MENU button.
6
Press the four-way controller (5).
The [QPlayback] menu will be displayed.
3
4
Press the four-way controller (23) to select [Resize].
Press the four-way controller (5).
100-0001
The Resize screen will be displayed.
Exit OK OK
MENU
5
6
Use the four-way controller (45) to select the image
you want to resize.
Press the OK button.
100-0001
Select resolution
and quality
Recorded Pixels 320 240
Quality Level
Exit OK OK
MENU
85
Download from Www.Somanuals.com. All Manuals Search And Download.
7
8
9
Select [Recorded Pixels] with the four-way controller
(45).
Press the four-way controller (3).
The frame will move to [Quality Level].
Press the four-way controller (45) to select [Quality
Level].
10 Press the OK button.
11 Press the four-way controller (23) to select
[Overwrite] or [Save as].
12 Press the OK button.
The image will be resized.
• Movie pictures cannot be resized.
• You cannot select a larger size than that of the original image.
• You cannot select a higher quality than that of the original image.
6
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Trimming Images
You can trim part of a picture and save it as a separate image.
1
2
Press the MENU button.
Press the four-way controller (5).
The [QPlayback] menu will be displayed.
3
4
5
6
7
Press the four-way controller (23) to select
[Trimming].
Press the four-way controller (5).
The image that can be trimmed will be displayed.
Use the four-way controller (45) to select the image
you want to trim.
Press the OK button.
The trimming screen will be displayed.
100-0001
Trim the image.
MENU
Exit
OK
• Operations available on the Trimming
screen.
Size
Roteate
OK
6
Zoom/f/ybutton:
Changes the size of
the image.
Z button
Toggles between horizontal and vertical.
Four-way controller
(2345):
Moves the trimming position up or down and
left or right.
MENU button:
Returns to the screen for selecting the image
to be trimmed.
8
9
Press the OK button.
Use the four-way controller (45) to
select the quality level after trimming.
100-0001
Select image quality
10 Press the OK button.
Quality Level
The trimmed image will be saved as a separate
image.
Exit OK OK
MENU
• Movie pictures cannot be trimmed.
• You cannot select a higher quality than that of the original image.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Four-way controller
OK button
MENU button
Editing Images with Digital Filters
The filters consist of color filters such as red, blue, and green, a soft filter
that produces a fuzzy effect, and a brightness filter that adjusts the
brightness of the image. In Digital Filter mode, these filters can be used
to edit an image.
• Color Filters (%)
Eight colors, black-and-white, sepia, red, pink, violet, blue, green and
yellow, are provided for the color filters. When you select a color filter in
the Digital Filter mode, the display on the LCD monitor is filtered with the
selected color, and the images are saved in that color.
6
• Soft Filter ($)
Images edited with the soft filter can be given a fuzzy effect and saved.
• Brightness Filter (&)
Images edited with the brightness filter can be brightened or darkened
and saved.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Press the MENU button in Playback mode.
Press the four-way controller (23) to select [Digital
Filter].
3
4
5
Press the four-way controller (5).
The digital filter setup screen will be displayed.
Use the four-way controller (45) to select the image
you want to edit.
Press the four-way controller (23)
to select the desired digital filter.
100-0001
The filtered image will be displayed on the LCD
monitor.
Exit OK OK
MENU
• Operations available with the brightness filter [&]
Zoom/f/ybutton (x)
Makes image brighter.
Zoom/f/ybutton (w) Makes the image darker.
6
6
7
Press the OK button.
Press the four-way controller (23) to select
[Overwrite] or [Save as].
8
Press the OK button.
The image edited with the digital filters will be saved.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Settings
How to recall the [B Set-up] menu
Four-way controller
OK button
MENU button
Rec. Mode
Set-up
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Format
Sound
AWB
Data Adjust
World Time
Language/
01/01/2003
Multiple
On
English
MENU
1/3
Exit OK OK
1/3
Exit OK OK
MENU
6
Formatting an SD Memory Card / MultiMediaCard
Formatting will delete all the data on the SD Memory Card/
MultiMediaCard.
• Do not open the card cover while the SD Memory Card /
MultiMediaCard is being formatted. The card may be damaged and
become unusable.
• SD Memory Cards/MultiMediaCards formatted on a PC or device
other than the camera cannot be used. Be sure to format the card with
the camera.
• Please note that formatting will delete protected images as well.
1
2
Select [Format] on the [B Set-up] menu.
Press the four-way controller (5).
The format screen is displayed.
3
4
Select [Format] with the four-way controller (2).
Press the OK button.
Formatting begins. When formatting is complete, the camera is ready
to take a picture.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Sound Settings
You can change the volume of the start-up sound, shutter sound,
operation sounds, and self-timer sound. You can also change the type
of each sound.
Changing the volume
1
2
Select [Sound] on the [B Set-up] menu.
Press the four-way controller (5).
The Sound screen will be displayed.
Sound
Volume
Start-up Sound
Shutter Sound
Operation Sound
1
1
1
Self-timer Sound On
Exit OK OK
MENU
Customize
3
4
Use the four-way controller (45) to change the
volume.
Press the OK button 2 times.
The camera is ready for capture or playback.
6
Changing the type of start-up, shutter, operation, or self-timer sound
1
2
Select [Sound] on the [B Set-up] menu.
Press the four-way controller (5).
The Sound screen will be displayed.
3
Press the four-way controller (23) to select [Start-up
Sound] and use the four-way controller 45) to select
[1], [2], [3] or [Off].
4
5
Change [Shutter Sound], [Operation Sound], and [Self-
timer Sound] in the same way.
For the self-timer sound, select [On] or [Off].
Press the OK button 2 times.
The camera is ready for capture or playback.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
How to recall the [B Set-up] menu
Four-way controller
OK button
MENU button
Rec. Mode
Set-up
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Format
Sound
AWB
Data Adjust
World Time
Language/
01/01/2003
Multiple
On
English
MENU
1/3
Exit OK OK
1/3
Exit OK OK
MENU
Changing the Date Style and Date / Time
You can change the initial date and time settings. You can also set the
date display style. Choose from yy/mm/dd, mm/dd/yy, and dd/mm/yy.
6
1
2
Select [Date Adjust] on the [B Set-up] menu.
Press the four-way controller (5).
The Date Adjust screen is displayed.
See “Initial Settings (p.20)” for instructions on setting the date and
time.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting World Time
The date and time set in “Initial Settings (p.20)” are the Home Time (your
usual time zone) setting.
Setting World Time enables you to display the local date and time on the
monitor when traveling overseas.
1
2
Select [World Time] on the [B Set-up] menu.
Press the four-way controller (5).
World Time
The World Time screen will be dis-played.
3
Switch O (On) and P (Off) with the
four-way controller (45).
NYC 07:18
NYC 07:18
Exit OK OK
MENU
O: The time in the country selected in World
Time will be displayed.
P: The time in the country selected in Home Time will be displayed.
4
Press the four-way controller (3).
If New York is selected as the world time city, then the cross-shaped
line is located in New York on the world map, and then Xindicates the
current time in New York (NYC).
6
5
6
7
8
9
Use the four-way controller (45) to select the World
Time city and press the four-way controller (3).
Set the daylight saving time to On (Y) or Off (Z) with the
four-way controller (45).
Press the four-way controller (3).
New York (NYC) is selected as the Home Time city [W] at first.
Repeat steps 5 and 6 to change the Home Time city and
DST setting.
Press the OK button twice.
The camera is ready to capture or play back images with the time in
the selected city.
See the list on p.103 for available cities and their codes.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
How to recall the [B Set-up] menu
Four-way controller
OK button
MENU button
Rec. Mode
Set-up
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Format
Sound
AWB
Data Adjust
World Time
Language/
01/01/2003
Multiple
On
English
MENU
1/3
Exit OK OK
1/3
Exit OK OK
MENU
Changing the Display Language
You can change the language of the menus and error messages.
6
1
2
Select [Language/
] on the [B Set-up] menu.
Press the four-way controller (45) to change the
language.
3
Press the OK button.
The camera is ready for capture or playback.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Display Mode
This determines the content displayed on the LCD monitor. You can
select Normal, Histogram, No. Info, or Off. Capture mode and Playback
mode display different information on the screen.
Normal
Capture Mode
Playback Mode
10 11
Capture information is
displayed.
1
2
3
4
6
9
1
2
3
4
5
6
7
8
9
Flash
Drive Mode
100
Start
100-0001
Focus Mode
Capture Mode
Autofocus frame
Capacity remaining
Battery symbol
Date and time
Voice memo
10/10//2003
11:20
10/10//2003
11:20
7
5
8
7
8
12
10 Folder name/File name
11 Protect icon
12 Four-way controller operation guide
6
Histogram
Capture Mode
Playback Mode
Brightness distribution is
displayed. The horizontal
axis shows the brightness
(dark to bright, left to right),
and the vertical axis shows
the number of pixels.
8
1
2
3
1
2 3
100
Start
100-0001
640
AWB
640
AWB
AUTO
200
1
2
3
4
5
6
7
8
Recorded pixels
Quality level
White balance
AE Metering
Sensitivity
Histogram
Aperture value
Shutter speed
1/ 100
F3.9
10/10//2003
11:20
6
5 4
7
6
5
4
• During Autofocus, the Autofocus frame is displayed.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
How to recall the [B Set-up] menu
Four-way controller
OK button
MENU button
Rec. Mode
Set-up
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Format
Sound
AWB
Data Adjust
World Time
Language/
01/01/2003
Multiple
On
English
MENU
1/3
Exit OK OK
1/3
Exit OK OK
MENU
No. Info
Capture Mode
Playback Mode
Capture information is not
displayed.
• During Autofocus, the
Autofocus frame (in Capture
mode) is displayed.
6
• Settings are displayed for
several seconds when changed.
Off
Capture Mode
Turns off the LCD monitor.
(The LCD monitor is not
turned off in Playback mode.)
Playback Mode
1
2
Select [Display] on the [B Set-up] menu.
Press the four-way controller (45) to select the
desired display mode.
3
Press the OK button.
The camera is ready for capture or playback.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Start-up Screen
You can display an image recorded with the camera as the welcome
screen when the camera is turned on.
1
2
Select [Screen Setting] on the [B Set-up] menu.
Press the four-way controller (5).
The Screen Setting screen will be displayed.
3
4
Press the four-way controller (5).
The screen for changing the start-up screen will
be displayed.
Change Start-up Screen
Start-up Screen
Optio
Press the four-way controller (45)
to select O (On) or P (Off).
MENU
Image
Exit OK OK
O
P
Displays the start-up screen.
Does not display the start-up screen.
5
6
Press the Z button.
Use the four-way controller (45) to select the image
you want to display as the start-up screen.
6
7
Press the OK button 4 times.
The camera is ready for capture or playback.
Once the start-up screen has been set, it will not be erased even if the
original image is deleted or the SD Memory Card / MultiMediaCard is
formatted. To delete the start-up screen, reset the setting. (1p.99)
97
Download from Www.Somanuals.com. All Manuals Search And Download.
How to recall the [B Set-up] menu
Four-way controller
OK button
MENU button
Rec. Mode
Set-up
Recorded Pixels
Quality Level
White Balance
Focusing Area
AE Metering
2048 1536
Format
Sound
AWB
Data Adjust
World Time
Language/
01/01/2003
Multiple
On
English
MENU
1/3
Exit OK OK
1/3
Exit OK OK
MENU
Setting the Background Color
This sets the background design and color displayed on the LCD
monitor.
6
1
2
Select [Screen Setting] on the [B Set-up] menu.
Press the four-way controller (5).
The Screen Setting screen will be displayed.
3
4
5
Press the four-way controller (3) to select [Background
color].
Press the four-way controller (45) to select the
background color.
Press the OK button twice.
The camera is ready for capture or playback.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Video Output Format
You can select the output format (NTSC or PAL) for capturing or playing
back images on a TV monitor.
1
2
Select [Video Out] on the [B Set-up] menu.
Press the four-way controller (45) to select [NTSC] or
[PAL], to match your TV output format.
3
Press the OK button.
The camera is ready for capture or playback.
Japan uses NTSC.
Setting Auto Power Off
You can set the camera to turn off automatically after a certain length of
inactivity.
1
2
Select [Auto Power Off] on the [B Set-up] menu.
6
Press the four-way controller (45) to select [3 min],
[5min], or [Off].
3
Press the OK button.
The camera is ready for capture or playback.
The Auto Power Off function will not work when the USB cable is
connected.
Resetting to Default Settings [Reset]
This resets all settings other than Date/Time, Language, Video Out,
Date Style, and World Time.
1
2
Select [Reset] on the [B Set-up] menu.
Press the four-way controller (5).
The Reset screen is displayed.
3
4
Press the four-way controller (2) to select [Reset].
Press the OK button.
The camera is ready for capture or playback.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Alarm
You can set the alarm to ring at a specified time and display a selected
image.
Playback button
Four-way controller
OK button
MENU button
Checking the Alarm
1
2
Press the MENU button.
Press the four-way controller (5).
The [QPlayback] menu will be displayed.
6
3
4
Press the four-way controller (23) to select [Alarm].
Press the four-way controller (5).
Alarm
1
2
3
Off
Off
Off
The list of alarms will be displayed.
Active alarms are indicated by O.
5:30AM
7:30AM
12:00PM
Exit OK OK
MENU
5
Press the OK button twice.
If any alarms are enabled, the camera will be turned off and the alarms
will be set.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Alarm
1
2
Press the MENU button.
Press the four-way controller (5).
The [QPlayback] menu will be displayed.
3
4
Press the four-way controller (23) to select [Alarm].
Press the four-way controller (5).
Alarm
The list of alarms will be displayed.
1
2
3
Off
Off
Off
5:30AM
7:30AM
5
Press the four-way controller (23)
to select alarm 1, 2, or 3.
12:00PM
Exit OK OK
MENU
6
7
Press the four-way controller (5).
The screen for setting the alarm mode and time
will be displayed.
Alarm
1
Off
5:30AM
Press the four-way controller (23)
to select the number of times the
alarm will ring.
No Image
Exit OK OK
MENU
Image
Everyday The alarm will ring everyday at the set time.
6
Once
Off
The alarm rings once at the set time.
The alarm will not ring.
8
9
Press the four-way controller (5).
Press the four-way controller (23) to set the time
(hour) the alarm will ring.
10 Repeat steps 8 and 9 above to set the alarm time
(minute) and set S(Snooze) to O (On) or P (Off).
If the Snooze is set to
O, the alarm will ring 5 times at 5-minute intervals.
11 Press the Z button.
12 Press the four-way controller (45) to select the image
to be displayed when the alarm rings.
13 Press the OK button.
14 Press the OK button 3 times.
The camera will turn off.
When the camera is turned off and the set time is reached, the alarm will
ring for one minute. After the alarm turns off, the camera will turn off
automatically.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Alarm Off
1
To stop the alarm ringing, press any button.
The alarm will stop.
To cancel the Snooze function, press the MENU button and OK button
at the same time.
The alarm will not ring when the camera is turned on.
6
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
List of City Names
There are the cities and code numbers available for setting the world
time.
City
Code
TYO
GUM
SYD
NOU
WLG
AKL
PPG
HNL
ANC
YVR
SFO
LAX
YYC
DEN
MEX
CHI
City
Code
JNB
IST
Tokyo
Johannesburg
Instanbul
Cairo
Guam
Sydney
CAI
Noumea
Wellington
Auckland
Pagopago
Honolulu
Anchorage
Vancouver
San Francisco
Los Angeles
Calgary
Jerusalem
Moscow
Jeddah
JRS
MOW
JED
THR
DXB
KHI
Tehran
Dubai
Karachi
Kabul
KBL
MLE
DEL
CMB
KTM
DAC
RGN
BKK
KUL
VTE
SIN
Male
Delhi
Colombo
Kathmandu
Dacca
Denver
Mexico City
Chicago
Miami
Rangoon
Bangkok
Kuala Lumpur
Vientiane
Singapore
Phnom Penh
Ho chi Minh
Jakarta
MIA
7
Toronto
YTO
NYC
SCL
CCS
YHZ
BUE
SAO
RIO
New York
Santiago
Caracas
Halifax
PNH
SGN
JKT
Buenos Aires
Sao Paulo
Rio de Janeiro
Madrid
Hong Kong
Perth
HKG
PER
BJS
SHA
MNL
TPE
SEL
ADL
MAD
LON
PAR
MIL
Beijing
London
Shanghai
Manila
Paris
Milano
Taipei
Rome
ROM
BER
Seoul
Berlin
Adelaide
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages
The following messages may be displayed on the LCD monitor during
camera operation.
Compression error
Compression of the image you captured has failed.Change
Memory card full
The SD Memory Card / MultiMediaCard memory is full and
no more images or sound can be saved.Insert a new SD
Memory Card / MultiMediaCard or delete unwanted images
or sound.(p.16, 77)
You may be able to save the image by changing the quality
level or recorded pixels.(p.40, 41)
Data being recorded
The image/voice recording is being recorded on the SD
Memory Card / MultiMediaCard.
Image folder could not The maximum file number has been used, and no more
be created
images or sound can be saved.Insert a new SD Memory
Card / MultiMediaCard or format the card.(p.16, 90)
No image & sound
There are no images or sound saved in the SD Memory
Card / MultiMediaCard that can be played back.
Camera cannot display You are trying to play back an image not supported by this
this image
camera.You may be able to display this on a PC or another
brand of camera.
Image protected
This is displayed when you try to delete a protected image.
Setting being recorded The image/sound protect settings or DPOF settings are
being changed.
7
Settings not stored
The SD Memory Card / MultiMediaCard is full, and no more
DPOF settings can be made.Delete any unwanted images
or sound and try to make the settings again.
Alarm was set
Deleting
This is displayed when the alarm is set and the camera is
about to be automatically turned off.
An images or sound on the SD Memory Card /
MultiMediaCard is being deleted.
Battery depleted
The battery is exhausted.Replace the battery.(p.12)
Memory card error
Shooting and playback are impossible due to a problem
with the SD Memory Card / MultiMediaCard.Try displaying
it on a PC.
Card not formatted
The SD Memory Card / MultiMediaCard you have inserted
is unformatted or has been formatted on a PC or other
device and is not compatible with the camera.(p.90)
Formatting
The SD Memory Card / MultiMediaCard is being formatted.
No card in camera
An SD Memory Card / MultiMediaCard has not been
inserted into the camera.(p.16)
Card locked
The SD Memory Card is write protected. (p.18)
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Cause
Remedy
The camera will No batteries are
Check whether battery is installed. If not,
install battery.
not turn on.
installed.
Battery/card cover is
open.
Close the battery/card cover.
Battery is installed
incorrectly.
Check orientation of battery.Reinsert
battery according to the +-symbols in
the battery compartment.(p.12)
Battery is exhausted.
Install new batteries in the camera or use
the AC adapter.
No image on
the LCD
monitor
Camera is connected to The LCD monitor is always turned off
PC with USB cable. when the camera is connected to a PC.
Camera is connected to The LCD monitor is always turned off
TV. when the camera is connected to a TV.
Image is displayed but Images on the LCD monitor may be hard
hard to see.
to see when taking pictures outside in
sunlight.
Shutter release Flash is charging.
button will not
work.
While the flash status lamp is blinking red,
the flash is being charged and a picture
cannot be taken.The lamp lights red when
charging is complete.
SD Memory Card /
MultiMediaCard is full.
Insert an SD Memory Card /
MultiMediaCard that is not full, or delete
unwanted images.(p.16, 77)
7
Camera is recording.
Please wait until recording is finished.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Cause
Remedy
Out of focus
Subject is difficult for
Autofocus to handle.
Subjects difficult for Autofocus include
those with low contrast (blue skies, white
walls), dark objects, fine-patterned
objects, fast-moving objects, and
landscapes seen through a window or
net.Focus on something at the same
distance as your subject, lock the focus
(by pressing shutter release button
halfway), aim at your subject, and press
shutter release button fully.
Subject is not in
Focusing Area
Position focusing target within the frame
(Focusing Area) at the center of the LCD
screen.If your subject is not within the
Focusing area, first focus on your subject
within the AF area, lock the focus (by
pressing shutter release button halfway),
then reframe your picture as desired, and
press shutter release button fully.
Subject is too close.
Set the focus mode to q. (p.37)
The focus mode is set to When the focus mode is set to q, normal
q. range pictures will be out of focus.
Picture is dark. Subject is too far away in If the subject is too far away, the image will
a dark environment
(night-scenes, etc.).
be dark.Take the picture within the flash
range.
Background is dark.
a dark background, the person may
appear clearly while the background
appears dark because the flash does not
reach the background.If you select the /
or &mode on the virtual dial screen, both
the person and the night-scene will be
clear. (p.50)
Flash does not The Flash Mode is set to Set to Auto or b(p.39)
fire.
Off.
The Capture mode is set The flash will not fire in these modes.
to C, Continuous
Shooting, or smode or
the Flash mode is set to
G.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Specifications
Model
Fully-automatic compact weather-resistant (JIS class 5) digital still camera
with housed zoom lens
Effective Pixels
Sensor
3.2 megapixels
3.34 megapixels (total pixels), 1/2.7 inch interline transfer CCD with a
primary color filter
Recorded Pixels
Still
2048x1536 pixels, 1600x1200 pixels,
1024x768 pixels, 640x480 pixels
Movie picture 320x240 pixels, 160x240 pixels
Sensitivity
Auto, Manual (Equivalent to ISO50, ISO100, ISO200, and ISO400)
File Format
Still
JPEG (Exif2.2), DCF, DPOF, PRINT Image Matching II
Movie picture MOV (QuickTime Motion JPEG), about 15fps
Best, Better, Good
Quality Level
Storage Medium
Image Storage Capacity
SD Memory Card, MultiMediaCard
Quality Level
Movie
Movie
Voice
Best
Better
Good
picture
picture
recording
Recorded Pixels
2048×1536
1600×1200
1024×768
640×480
(320
×240) (160
×120)
7
11
25
53
12
20
45
82
18
27
40sec.
150sec.
30min.
56
100
•
Exposure capacity when using a 16MB SD Memory Card.
7
White Balance
Lens
Auto, Daylight, Shade, Tungsten Light, Fluorescent light, Manual
Focal Length
5.7mm - 16mm (Equivalent to 37 - 104mm in 35mm
format)
Max. aperture
f/2.8 - f/3.9
Lens Composition
10 elements in 7 groups (one lens aspherical on
both sides)
Zoom Type
Electrically driven
Capture Range
16.8mm × 12.4mm (full screen) (Using macro mode
or manual focus at max. WIDE position)
Digital Zoom
Viewfinder
Capture Mode
Max 4× (Combines with 2.8× optical zoom to
provide zoom equivalent to 11.2× max.)
Type
Magnification
Real optical zoom viewfinder
Wide 0.3×, Tele 0.71×
LCD monitor
1.6-inch 1.6TFT color LCD, 84 kilomegapixels
Playback Functions
Single-frame, 9-frame index, zoom (max. 8×), scroll, slideshow, movie
playback, sound playback, histogram display, trimming, resize, digital filters
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Autofocus system
Manual Focus
Type
TTL contrast detection by sensor
Capture Range
(From lens front)
Normal: 0.3m - ∞ (full zoom range)
Macro: 0.01m - 0.5m (Wide), 0.2m -0.5m (Tele) (full
zoom range)
Infinity-landscape: ∞ (full zoom range)
Focus Lock
By pressing the shutter release button halfway
0.01m - ∞ (Wide), 0.2m - ∞ (Tele)
Exposure Mechanism AE Metering
TTL metering by sensor (multi-segment, center-
weighted, spot)
Exposure Modes
Program, Picture mode, Movie Picture, Panorama
Assist, Voice Recording
EV Compensation
Movie Picture
Model
±2EV (Can be set in 1/3EV steps)
Recording time by vacant memory
Electronic/Mechanical shutter
Shutter
Flash
Speed
Approx. 1/2000 sec - 4 sec.
Model
Automatic flash with red-eye reduction function
Flash Modes
Auto, Flash Off, Flash On, Auto+Red-eye reduction,
Flash On+Red-eye reduction
Capture Range
Wide Approx. 0.1m - 2.9m w/Sensitivity AUTO
Tele Approx. 0.5m - 2.1m w/Sensitivity AUTO
Drive Modes
Single-frame Shooting, Self-timer Shooting, Continuous Shooting, Multi
Continuous Shooting, Interval Shooting
Self-timer
Electrically controlled, operation time approx. 10 seconds
World Time settings for 62 cities (28 time zones)
Time function
Power Supply
Lithium battery CR-V3, two AA batteries (Alkaline, Ni-MH, Lithium),
AC Adapter (optional)
Battery Life
I/O Ports
Approx. 540
images
(with 50% of shooting using flash, and using lithium
battery CR-V3)
Note: Based on PENTAX measuring conditions.
7
USB/AV terminal (PC communication USB1.1), external power supply
terminal
Video Output Format
NTSC/PAL
Size
81.5 (W) × 76 (H) × 30.5 (D) mm (excluding protruding parts)
160 g (excluding batteries and SD Memory Card / MultiMediaCard)
Weight
Weight when shooting 208 g (including batteries and SD Memory Card / MultiMediaCard)
Accessories
AA batteries (2), AV cable, USB cable, software (CD-ROM), strap, 16MB
SD Memory Card, operating manual, warranty
Water resistant
Equivalent to JIS Class 5 and 7
109
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY POLICY
All PENTAX cameras purchased through authorized bona fide photographic
distribution channels are guaranteed against defects of material or workmanship
for a period of twelve months from date of purchase. Service will be rendered, and
defective parts will be replaced without cost to you within that period, provided the
equipment does not show evidence of impact, sand or liquid damage,
mishandling, tampering, battery or chemical corrosion, operation contrary to
operating instructions, or modification by an unauthorized repair shop. The
manufacturer or its authorized representatives shall not be liable for any repair or
alterations except those made with its written consent and shall not be liable for
damages from delay or loss of use or from other indirect or consequential
damages of any kind, whether caused by defective material or workmanship or
otherwise; and it is expressly agreed that the liability of the manufacturer or its
representatives under all guarantees or warranties, whether expressed or
implied, is strictly limited to the replacement of parts as hereinbefore provided. No
refunds will be made on repairs by nonauthorized PENTAX service facilities.
Procedure During 12-month Warranty Period
Any PENTAX which proves defective during the 12-month warranty period should
be returned to the dealer from whom you purchased the equipment or to the
manufacturer. If there are no representatives
of the manufacturer in your country, send the equipment to the manufacturer, with
postage prepaid. In this case, it will take a considerable length of time before the
equipment can be returned to you owing to the complicated customs procedures
required. If the equipment is covered by warranty, repairs will be made and parts
replaced free of charge, and the equipment will be returned to you upon
completion of servicing. If the equipment is not covered by warranty, regular
charges of the manufacturer or of its representatives will apply. Shipping charges
are to be borne by the owner. If your PENTAX was purchased outside of the
country where you wish to have it serviced during the warranty period, regular
handling and servicing fees may be charged by the manufacturer’s
7
representatives in that country. Notwithstanding this, your PENTAX returned to
the manufacturer will be serviced free of charge according to this procedure and
warranty policy. In any case, however, shipping charges and customs clearance
fees to be borne by the sender. To prove the date of your purchase when
required, please keep the receipt or bills covering the purchase of your equipment
for at least a year. Before sending your equipment for servicing, please make sure
that you are sending it to the manufacturer’s authorized representatives or their
approved repair shops, unless you are sending it directly to the manufacturer.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Always obtain a quotation for the service charge, and only after you accept the
quoted service charge, instruct the service station to proceed with the servicing.
• This warranty policy does not affect the customer’s statutory rights.
• The local warranty policies available from PENTAX distributors in some
countries can supersede this warranty policy. Therefore, we recommend
that you review the warranty card supplied with your product at the time
of purchase, or contact the PENTAX distributor in your country for more
information and to receive a copy of the warranty policy.
7
The CE Mark is a Directive conformity mark of the European
Community.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
For customers in USA
STATEMENT OF FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
7
Consult the dealer or an experienced radio/TV technician for help.
For customers in Canada
This Class B digital apparatus meets all requirements of the Canadian
Interference - Causing Equipment Regulations.
Pour les utilisateurs au Canada
Cet apareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
The CE Mark is a Directive conformity mark of the European
Community.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
According to 47CFR, Parts 2 and 15 for
Class B Personal Computers and Peripherals
We:
PENTAX U.S.A., Inc.
Located at: 600 12th Street, Suite 300,
Golden, Colorado 80401, U.S.A
Phone: 303-799-8000 FAX: 303-790-1131
Declare under sole responsibility that the product identified herein,
complies with 47CFR Parts 2 and 15 of the FCC rules as a Class B digital
device. Each product marketed, is identical to the representative unit
tested and found to be compliant with the standards. Records
maintained continue to reflect the equipment being produced
can be expected to be within the variation accepted, due to quantity
production and testing on the statistical basis as required by 47CFR
§2.909. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may
cause undesired operation. The above named party is responsible for
ensuring that the equipment complies with the standards of 47CFR
§15.101 to §15.109.
7
Product Name: PENTAX Digital Still Camera
Model Number: Optio 33WR
Contact person: Customer Service Manager
Date and Place: August, 2003, Colorado
113
Download from Www.Somanuals.com. All Manuals Search And Download.
PENTAX Corporation
2-36-9,Maeno-cho, Itabashi-ku, Tokyo 174-8639,
JAPAN
(http://www.pentax.co.jp/)
PENTAX Europe GmbH (European Headquarters)
Julius-Vosseler-Strasse, 104, 22527 Hamburg,
GERMANY
(HQ - http://www.pentaxeurope.com)
(Germany - http://www.pentax.de)
PENTAX U.K. Limited
PENTAX House, Heron Drive, Langley, Slough,
Berks SL3 8PN, U.K.
(http://www.pentax.co.uk)
PENTAX France S.A.S.
PENTAX Benelux B.V.
12/14, rue Jean Poulmarch, 95106 Argenteuil
Cedex, FRANCE
(for Netherlands)
Spinveld 25, 4815 HR Breda, NETHERLANDS
(http://www.pentax.nl)
(for Belgium & Luxembourg)
Weiveldlaan 3-5, 1930 Zaventem, BELGIUM
(http://www.pentax.be)
PENTAX (Schweiz) AG
Widenholzstrasse 1 Postfach 367 8305 Dietlikon,
SWITZERLAND (http://www.pentax.ch)
PENTAX Scandinavia AB P.O. Box 650, 75127 Uppsala, SWEDEN
(http://www.pentax.se)
PENTAX U.S.A., Inc
PENTAX Canada Inc.
600 12th Street, Suite 300,
Golden, Colorado 80401, U.S.A
(http://www.pentax.com)
3131 Universal Drive, Mississauga, Ontario L4X
2E5, CANADA
(http://www.pentaxcanada.ca)
• Printed on recycled paper
• Specifications and external dimensions are subject to change without notice.
57317 Copyright © PENTAX Corporation 2003
02-200310 Printed in Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|