SM/SMBW 2000 Series™ Filter
Installation
and
User's Guide
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
i
Table of Contents
Important Safety Precautions..............................................................................................ii
Section 1: Introduction .....................................................................................................1
SM/SMBW 2000 Series™ Filter Overview ...............................................................1
General Features.....................................................................................................2
Section 2: Filter Operation ...............................................................................................3
General Information .................................................................................................3
What is Diatomaceous Earth and how does it Filter Water......................................4
Filter Precoating Installations...................................................................................4
Section 3: Filter Installation..............................................................................................5
General Information .................................................................................................5
Operating the Filter ..................................................................................................6
Section 4: Maintenance .....................................................................................................7
Backwashing (Cleaning) the SM/SMBW 2000 Series™ Filter..................................7
Cleaning the Separation Tank ..................................................................................7
Cleaning Filter Manually & Winterizing.....................................................................8
How to use the Filter Lid Opening Tool ....................................................................9
Section 5: Troubleshooting ..............................................................................................10
Section 6: Replacement Parts ..........................................................................................11
Replacement Parts for SM/SMBW 2000 Series™ Filter...........................................11
Flow Rate Information..............................................................................................11
Replacement Parts for Rotary Valve .......................................................................12
Head Loss Comparison Curves ..............................................................................12
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
IMPORTANT SAFETY PRECAUTIONS
Body
Important Notice:
This guide provides installation and operation instructions for the SM/SMBW 2000 Series™ Filter.
Consult Pentair Water Pool and Spa™ with any questions regarding this equipment.
Attention Installer: This guide contains important information about the installation, operation and safe use of
this product. This information should be given to the owner and/or operator of this equipment after installation or left on
or near the filter.
Attention User: This manual contains important information that will help you in operating and maintaining this
filter. Please retain it for future reference.
WARNING —Before installing this product, read and follow all warning notices and instructions which are
included. Failure to follow safety warnings and instructions can result in severe injury, death,
or property damage. Call (800) 831-7133 for additional free copies of these instructions.
Consumer Information and Safety
The SM/SMBW 2000 Series™ Filters are designed and manufactured to provide many years of safe and reliable service
when installed, operated and maintained according to the information in this manual and the installation codes referred
to in later sections. Throughout the manual, safety warnings and cautions are identified by the “ “ symbol. Be sure
to read and comply with all of the warnings and cautions.
WARNING —Do not operate the filter until you have read and understand clearly all the operating instructions
and warning messages for all equipment that is a part of the pool circulating system. The
following instructions are intended as a guide for initially operating the filter in a general pool
installation, however each installation may have unique conditions where the starting procedure
could be different. Failure to follow all operating instructions and warning messages can result
in severe injury, death, or property damage.
WARNING —THIS FILTER OPERATES UNDER HIGH PRESSURE.
When any part of the circulating system, (e.g., clamp, pump, filter, valve(s), etc.), is serviced, air
can enter the system and become pressurized. Pressurized air can cause the lid to be blown off
which can result in severe injury, death, or property damage. To avoid this potential hazard, follow
these instructions:
1. Beforerepositioningvalve(s)andbeforebeginningtheassembly, disassembly, oradjustment
of the clamp or any other service of the circulating system: (A) Turn the pump OFF and shut
OFF any automatic controls to ensure the system is NOT inadvertently started during the
servicing;(B)opentheHighFlow™manualairreliefvalve;(C)waituntilallpressureisrelieved.
2. Whenever installing the filter clamp FOLLOW THE FILTER CLAMP INSTALLATION
INSTRUCTIONS EXACTLY.
3. Once service on the circulating system is complete FOLLOW SYSTEM RESTART
INSTRUCTIONS EXACTLY.
4. Maintain circulation system properly. Replace worn or damaged parts immediately,
(e.g., clamp, pressure gauge, valve(s), o-rings, etc).
5. Be sure that the filter is properly mounted and positioned according to instructions provided.
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
IMPORTANT SAFETY PRECAUTIONS (continued)
WARNING —Due to the potential risk that can be involved it is recommended that the pressure test be kept to the
minimum time required by the local code. Do not allow people to work around the system when the
circulation system is under pressure test. Post appropriate warning signs and establish a barrier
around the pressurized equipment. If the equipment is located in an equipment room, lock the door
and post a warning sign.
Never attempt to adjust any closures or lids or attempt to remove or tighten bolts when the system is
pressurized. These actions can result in a separation or failure of system components. This
instantaneous release of energy can cause components to be accelerated to high velocities and to
travel far distances. These components could cause severe personal injury or death if they were to
strike a person.
WARNING —Risk of electrical shock or electrocution.
This pool filter must be installed by a qualified pool serviceman in accordance with the National
Electrical Code and all applicable local codes and ordinances.
Always disconnect power to the pool equipment at the circuit breaker before servicing any of the
equipment. Ensure that the disconnected circuit is locked out or properly tagged so that it cannot be
switched on while you are working on the pool equipment. Failure to do so could result in serious injury
or death to serviceman, pool users or others due to electric shock.
Position the filter and the air relief valve to safely direct water drainage and purged air or water. Water
discharged from an improperly positioned filter or valve can create an electrical hazard that can cause
severe personal injury as well as damage property.
WARNING —To reduce the risk of injury, do not permit children to use this product unless they are closely
supervised at all times.
CAUTION — This filter is for use with permanently installed pools and may also be used with hot tubs and spas if
so marked. Do not use with storable pools. A permanently installed pool is constructed in or on the
ground or in a building such that it cannot be readily disassembled for storage. A storable pool is
constructed so that it may be readily disassembled for storage and reassembled to its original
integrity.
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
IMPORTANT SAFETY PRECAUTIONS (continued)
General Installation Information
The following information should be read carefully since it outlines the proper manner of care and operation for your
filter system. You can expect maximum efficiency and life from your filtration system by following these instructions and
taking the necessary preventative care.
• Have a trained pool professional perform all pressure tests.
• Do not connect the system to a high pressure or city water system.
• Trapped air in the system can create a hazardous condition. BE SURE to purge all air from the
system before operating or testing equipment.
• DO NOT pressure test with compressed air!
• Check local codes for restrictions on backwash to waste piping, separation tank requirements and
spent D.E. disposal requirements.
• DO NOT use more than the recommended amount of D.E. in your filter. To do so can cause a buildup
of D.E. and “bridging” between the elements which will plug the filter.
• Piping must conform to local/state plumbing and sanitary codes.
• Support piping independently to prevent strains on filter or valve.
• Fittings restrict flow; for best efficiency, use the fewest possible fittings.
• A check valve installed ahead of the filter inlet will prevent contaminants from draining back into the
pool.
• A check valve installed between the filter and heater will prevent hot water from backing up into the
filter and deforming the internal components.
• To allow recirculation during precoat, (if precoat pot is used), install a recirculation line with shut-off
between pad return line and pump suction.
• All wiring, grounding and bonding of associated equipment must meet local and/or National Electrical
Code standards.
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Section 1
Introduction
SM/SMBW 2000 Series™ Filter Overview
The stainless steel classic for unmatched water clarity
Diatomaceous earth (D.E.) results not just in clean water, but water that really sparkles. D.E. filters remove
particles measured in microns that are individually undetected by the human eye, but combine to reduce water
clarity. Pentair SM/SMBW 2000 Series™ stainless steel D.E. filters not only filter better, they make your life
easier. That’s because they feature curved grids to maximize filter surface area, and more filter area means
longer periods between cleaning. In addition, a refined internal design minimizes flow restrictions so that the
least amount of pumping power produces the maximum required flow rates—for lower utility costs.
Crystal clear water has never been easier
Like all Pentair filters, SM/SMBW 2000 Series™ D.E. filters provide optimum filtration efficiency, easy
maintenance, and longer runs between cleanings. Their extraordinary dirt-holding capacity and easy cleanability
make them the perfect choice for every pool.
SM/SMBW 2000 Series
D.E. Filter
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
2
General Features
•
Exclusive curved filter grid design ensures an even flow and uniform distribution of D.E. for optimum
filtration efficiency and water clarity.
•
•
•
Stainless steel tank is strong and made to last for years and years.
Available in a range of sizes, with and without backwash valves, to meet your exact requirements.
Exclusive clamp ring design permits quick and easy access to internal components should service be
necessary.
•
2" plumbing connections for maximum flow, greater efficiency.
Additional Features:
•
•
•
•
Durable thermoplastic rotor will not corrode for long service life.
Individually-removable grids for easy cleaning.
Unique rotor seal keeps dirt out to ensure smooth operation and long life.
Attractive design has no external plumbing to detract from the filter’s clean lines.
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Section 2
Filter Operation
This section describes how the SM/SMBW 2000 Series™ filter operates.
General Information
WARNING — THIS FILTER OPERATES UNDER HIGH PRESSURE.
Pressurized air can cause the lid to be blown off which can result in severe injury, death, or property
damage. When clamped properly and operated without air in the water system, this filter will operate
in a safe manner.
1. Warning labels should be affixed to the top of the filter and on the clamp bands at all times. Keep safety
labels in good condition. Replace missing or damaged safety labels. {For free labels call (805) 553-5000 or
(919)566-8000.}
2. The "SM/SMBW" Series Filter has been listed and approved by the National Sanitation Foundation. This
booklet will enable you to install and operate your pool filter in the correct manner. Correct installation and
operation will result in the trouble free operation of a quality product, as well as prevent unnecessary
repairs.
3. Model SMBW Filter System
a. StandardSMSeriesFilterwithbuilt-inbackwashvalve. Simplifiesplumbinginstallations.
4. Model SM Filter System
a. Standard SM Series requires separate valves for backwash.
CAUTION — Before starting any filter system, be sure the pump has been adequately primed by filling the strainer
on the pump with water. Failure to do so will result in pump seal problems. When installing in
conjunction with a heater, a one-way check valve should be used between the filter and
heater to prevent the backflow of hot water from damaging the filter internals.
U.S. Patent No.
4,414,109
4,328,833
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
4
What is Diatomaceous Earth and how does it Filter Water
1. Diatomaceous earth is the skeletal remains of microscopic one-cell aquatic plants called diatoms, also
known as diatomite, D.E., and more properly diatomaceous earth.
2. Under the microscope, these minute diatoms show an amazingly intricate design and variety of forms, such
as disc-shaped, boat-shaped, needle-like and many have a lace-like porous structure.
3. When used as a filter aid, the diatomaceous earth is mixed with water to form a slurry for filter 'precoat'.
This mixture is introduced into the filter system by means of a slurry pot, or by pouring directly into the
surface skimmer with the pump running. The minute diatoms are deposited on the outer surface of the
filter elements, forming a 'strawpile' layer or cake by interlacing and overlapping, and thus providing
countless microscopic channels which entrap suspended impurities, but allow clear water to pass through
withoutclogging.
4. We recommend the use of D.E. which is sold and labeled for use with swimming pools and spas. These
grades of D.E. typically have a median particle size of 34 microns, which is ideal for most applications.
WARNING — Failure to operate your filter system or inadequate filtration can cause poor water clarity obstructing
visibility in your pool and can allow diving in the shallow pool area, or diving into or on top of
obscured objects which can cause serious bodily injury or drowning.
Filter Precoating Instruction
1. Mix the Diatomaceous Earth {D.E.} in a pail of water to form a slurry, then pour the mixture directly into
the surface skimmer with the pump running. Insure that the right quantity of D.E. is used as shown in the
D.E. Precoat Requirements below in Table 1.
Diatomaceous Earth (D.E.)
Precoat Requirements
Table 1.
Filter Model
Number
* By Weight
Pounds
2036
2048
2060
2072
3.6
4.8
6.0
7.2
* By Weight - 1 lb. of D.E. per 10 sq. ft. of filter surface area.
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Section 3
Filter Installation
The following general information describes how to install the SM/SMBW 2000 Series™ Filter.
Note: Before installing this product, read and follow all warning notices and instructions starting on page ii.
General Filter Information
WARNING — THIS FILTER OPERATES UNDER HIGH PRESSURE. When any part of the circulating system,
(e.g., clamp, pump, filter, valve(s), etc.), is serviced, air can enter the system and become pressurized.
Pressurized air can cause the lid to be blown off which can result in severe injury, death, or property
damage. To avoid this potential hazard, follow these instructions:
1. Before repositioning valve(s) and before beginning the assembly, disassembly, or adjustment
of the clamp or any other service of the circulating system: (A) Turn the pump OFF and shut OFF
any automatic controls to ensure the system is NOT inadvertently started during the servicing;
(B) open the manual air relief valve; (C) wait until all pressure is relieved.
2. Whenever installing the filter clamp FOLLOW THE FILTER CLAMP INSTALLATION
INSTRUCTIONS EXACTLY.
3. Once service on the circulating system is complete FOLLOW SYSTEM RESTART
INSTRUCTIONS EXACTLY.
4. Maintain circulation system properly. Replace worn or damaged parts immediately, (e.g., clamp,
pressure gauge, valve(s), o-rings, etc).
5. Be sure that the filter is properly mounted and positioned according to instructions provided.
1. New pools have a tremendous amount of debris due to dirt in the lines, plaster dust, etc. This debris will be
removed by the filter and will require daily backwashing of the filter until it is removed. Check the pressure
gauge daily and backwash the filter when the pressure increases 8 - 10 psi over the initial reading. It will
require several backwashings before the pool is clean. Thereafter, the normal filter cycle will be several
weeks in a properly designed system. The filter cycle is lengthened or shortened by contamination loads.
2. When installing backwash lines, it is recommended to install a vacuum breaker where the backwash line is
over 40 feet long, or if the line discharges 10 feet or more lower than the water level of the pool.
Operating at excessive vacuum levels can cause the tank to implode, which voids the warranty.
3. A check valve is recommended between the filter and heater to prevent hot water backup from damaging
the filter internals.
4. The maximum operating pressure of the tank is 50 psi. Never operate the unit above this pressure or
attach a pump to this filter that has a shut off pressure higher than 50 psi.
5. Never install a chemical feeder or ozonator upstream of the filter. Always locate downstream with a
check valve between the feeder and the filter.
6. A positive shut off valve is not recommended downstream of the filter and/or heater. If the system is ever
run with such a valve closed, the internal air vent becomes inoperative and an explosive situation could
exist. Running the system with no flow can seriously damage the equipment.
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7. Clean your filter when pressure reads between 8-10 psi higher than the original starting pressure. Your
filter pressure reading will increase as it removes dirt from your pool. However, this buildup of pressure
will vary due to different bathing loads, temperature, weather conditions, etc.
a. MY ORIGINAL STARTING PRESSURE IS ___________ psi (pounds per square inch). I SHOULD
BACKWASH (CLEAN) THE FILTER AT __________ psi.
8. Check carton for any evidence of damage due to rough
handling in shipment. If carton or any filter components are
damaged, notify freight carrier immediately.
9. The filter should be mounted on a level concrete slab.
Position the filter so that instructions, warnings and the
pressure gauge are visible to the operator. It also should be
positioned so that the piping connections, control valve and
drain port are convenient and accessible for servicing and
winterizing.
10. Provide space and lighting for routine maintenance access.
Do not mount electrical controls over filter. Install electrical
Figure 1.
controls (e.g., on/off switches, timers, control systems, etc.)
at least five (5) feet from the filter. This will allow you
enough room to stand clear of the filter during
system start up.
Vertical
ClearanceReq. NSF
11. Allow sufficient clearance around the filter to permit
visual verification that the clamp is properly installed
around the tank flanges, see Figure 1.
Model
SM/SMBW-2036
SM/SMBW-2048
SM/SMBW-2060
SM/SMBW-2072
60 in.
66 in.
72 in.
78 in.
yes
yes
yes
yes
12. Allow sufficient space above the filter to remove
the filter lid for cleaning and servicing. This
distance will vary with the model of filter you are
using. See Table 2 for the required vertical
clearance.
Table 2.
How to Operate Filter
WARNING —THIS FILTER OPERATES UNDER HIGH PRESSURE.
When any part of the circulating system, e.g., clamp, pump, filter, valve(s), etc. is serviced, air can enter
the system and become pressurized. Pressurized air can cause the lid to be blown off which can result
in severe injury, death, or property damage. To avoid this potential hazard, follow these instructions.
1. Set rotary valve handle in the filter position.
2. Open air relief valve on top of filter. STAND CLEAR OF THE FILTER.
3. Start pump and wait until a steady jet of water emerges from air relief valve, then close valve.
4. Introduce the required amount of Diatomaceous Earth into filter, see page 4, Table 1.
5. Filter will operate efficiently until pressure gauge indicates time for backwashing.
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Section 4
Maintenance
To Backwash (Clean) Filter
WARNING — To prevent equipment damage and possible bodily injury and/or property damage, always turn the
pump off before changing the valve positions.
1. Pressure backwashing is accomplished in four easy steps:
a. Turn pump off.
b. Rotate handle of rotary valve 90o as shown in Figure 2.
STAND CLEAR OF THE FILTER.
c. Turn pump on.
d. Backwash for approximately two minutes or until effluent
appears clean. When backwashing is complete, turn pump
off, rotate handle back to filter position and you are ready for
filter operation again. Precoat filter with D.E. as shown on
page 4, Table 1.
Figure 2.
How to Clean the Separation Tank, performed after each backwash operation. (If installed or if applicable.)
The purpose of the separation tank is to collect the spent diatomaceous earth during backwashing (cleaning) of
the filter. It must be cleaned after each backwash to prevent any clogging problems. It is recommended that this
procedure be repeated to ensure complete backwashing of the filter. One backwashing may not be sufficient.
1. Open valve “C” and valve “D”* to drain separation tank. While the tank drains, the filter can be pre-coated
and restored to the filter cycle. Be sure valve “B” is closed. See Figure 3.
WARNING — *Valve "D" is the air relief valve. It is important that this valve be opened before proceeding
further. The tank is pressurized and is dangerous if the air is not vented prior to removing the lid
clamp. Failure to open the air relief valve could cause the lid to separate resulting is serious bodily
injury and/or property damage.
2. To remove the clamping ring, partially unscrew the adjustment knob and release the head of the T-bolt from
the slotted bracket.
3. Remove tank lid with screwdriver or with a tool available from the manufacturer, see page 9, Figure 5. Avoid
cutting rubber O-ring.
4. When water has drained from bag, remove bag from tank by grasping the handles of the bag with both hands;
pushingdownwithonehand;pullingupwiththeotherandliftingbagout.
5. Turnbaginsideoutandemptycontentsisawastecontainer.Rinsebag
with garden hose.
6. Install bag in tank with the rim of the bag immediately below the tank
inletopening,thenpushdownontherimoppositetheinletopeninguntil
the rim is level.
7. Remove rubber O-ring and clean both O-ring and channel. Lubricate
O-ring with a non-water soluble grease or silicone lubricant and
replace O-ring in channel.
8. Clean the inside surface of the tank lid where it seals against the
Figure 3.
O-ring. Place lid on tank; push down on lid to seat in-place.
9. Replace the clamping ring. Engage the head of the T-bolt into the slotted bracket and tighten the adjustment
knob. Hand tighten only.
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
8
How to Clean Filter Manually & Winterizing Instructions
(Required at least once a year and when winterizing your filter to prevent damage during freezing conditions.)
1. Turn pump off.
2. Set valve handle or valves for backwash position, (for SMBW only).
3. STAND CLEAR OF THE FILTER - Turn pump on and run for 3 minutes, then turn pump off.
4. Drain filter with respect to opening the air relief valves as discussed in a, b, and c, below.
a. To drain filter Model SM with gate valves, open drain valve and tank air relief valve and close all other
valves.
WARNING — Valve "D" is the air relief valve. It is important that this valve be opened before proceeding
further. The tank is pressurized and is dangerous if the air is not vented prior to removing the lid
clamp. Failure to open the air relief valve could cause the lid to separate resulting is serious bodily
injury and/or property damage.
b. To drain filter model SMBW, set valve handle to backwash position and open tank air relief valve.
c. To drain filter model SMBW with Separation Tank, set valve handle to backwash position; open tank air
relief valve; close all other valves and remove drain plug on backwash line.
5. To remove the clamping ring, partially unscrew the adjustment knob and release the head of the T-bolt from
the slotted bracket.
6. Remove tank lid with screwdriver or with a tool available from the manufacturer, see page 9, Figure 5. Avoid
cutting rubber O-ring or bending of lid or tank O-ring channel.
7. Use garden hose to rinse down filter elements until all debris has been flushed from tank. Then screw drain
plug on backwash line on models with Separation Tank.
8. Unscrew wing nut; remove washer and unclip air vent tube from holding wheel. Remove holding wheel.
WARNING — Please heed all manufacturers' posted instructions, warnings and cautions when using
muriatic acid.
9. Lift out filter elements and scrub each element with a soft brush. If elements are coated with scale, it will be
necessarytobrushwithamildsolutionofmuriaticacid(10partswaterto1partmuriaticacid). Rinseelements
with water.
10. Remove manifold and inspect for damage. Replace rotor O-ring & lubricate as needed.
11. Replacecleanelementsinmanifoldsockets;notchonelementwillguideittoproperposition. Allelementsare
interchangeable.
12. Replace holding wheel over center rod; place washer over rod and turn holding wheel until elements spread
to widest gap. Replace washer, then screw wing nut on rod. Do not tighten nut beyond finger tight. Be
sure to clip air vent tube back into slot on holding wheel. Clean vent tube screen cap of any debris.
13. Remove rubber O-ring and clean both O-ring and channel. Lubricate O-ring with a non-water soluble grease
or silicone lubricant and replace O-ring in channel.
14. Clean the inside surface of the tank lid where it seals against the O-ring. Place lid on tank; push down on lid
to seat in place.
15. Replace the clamping ring. Engage the head of the T-bolt into the slotted bracket and tighten the adjustment
knob. (Hand tighten only.)
16. Torestoretothefiltercycle, refertotheoperatingandcleaninginstructionsofthefiltermodelinvolved. When
winterizing, ensure that all water is removed from the lower internal portion of the filter.
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
9
How to Use the Filter Lid Opener Tool
Pressure
Gauge
1. Turn pump off.
Air Relief
Valve
2. Open the air relief valve and wait for tank water to drain into pool.
See Figure 4.
Lid
Clamp
3. Remove the clamp ring.
4. Insert the filter lid opener as shown in Figure 5.
a. The tool fits under the O-Ring.
Tank
5. Liftthetanklidwiththefilterlidopenerinseveralplacesaroundthetank.
6. Consultpage7forFilterCleaningandpages5and6forFilterOperating
Instructions.
Lid
O-ring
Figure 4.
Filter Lid Opener
(2) Lift Up the
Filter Lid Opener
(1) Insert the
Filter Lid Opener
Tank
Figure 5.
The Pentair Water Pool and Spa Filter Lid Opener Tool may be used on any stainless steel filter tank
manufactured by Pentair Water Pool and Spa.
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Section 5
Troubleshooting
Use the following troubleshooting information to resolve possible problems with your SMBW 2000 Series™ Filter.
WARNING — THIS FILTER OPERATES UNDER HIGH PRESSURE.
When any part of the circulating system, (e.g., clamp, pump, filter, valve(s), etc.), is serviced, air can
enter the system and become pressurized. Pressurized air can cause the lid to be blown off which
can result in severe injury, death, or property damage.
1. If you are not familiar with your pool filtering system and/or heater:
a. Do NOT attempt to adjust or service without consulting your dealer, or a qualified pool
technician.
b. Read the entire Installation & User’s Guide before attempting to use, service or adjust the
pool filtering system or heater.
Note: Turn off power to unit prior to attempting service or repair.
Problems and Corrective Actions
SYMPTOMS
WHAT TO LOOK FOR
RECOMMENDED ACTION
Earth (D.E.) to Pool
Internal parts not assembled correctly.
Check assembly of internal parts making sure they are
correctly in place.
NOTE: Be sure the foreign
material in the pool is
diatomaceous earth.
Damaged manifold.
Torn element fabric.
Replace manifold.
Repair fabric or replace element.
Diatomaceous earth back up at main
drain.
Check for air leaks, repair as necessary. Air leaks can
cause system to drain down allowing D.E. back to the
pool.
Missing vent cap.
Damaged O-Ring.
Contaminated O-Ring.
Replace cap.
Leak at Lid
Replace O-Ring.
Clean O-Ring; clean inner lip of lid and retainer band at
top of tank.
Clamping band too loose.
Tighten clamping band.
Crack in lid or tank body.
Replace cracked part.
High Pressure Reading on
Filter Gauge
Restriction on discharge side.
Calcium deposits on filter elements.
Excessive water flow through filter
Locate and correct restriction of filter.
Remove and acid wash elements.
Establish pump flow rate and compare with max. filter flow
(pump horsepower may exceed filter flow rate requirement.
rate).
If heater is included in system, flow valve Adjust or replace flow valve as necessary.
on heater may be stuck open.
Filter gauge not working properly.
Poor backwash procedure.
Too little or too much D.E.
Algae in water.
Inspect and repair gauge; replace if necessary.
Use correct backwash procedure.
Short Filter Cycle
Backwash and add correct amount of D.E.
Correct and maintain proper water chemistry. Frequent
backwashing may be necessary until pool is free of algae.
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Section 6
Replacement Parts
Replacement Parts List
Model SM/SMBW 2000 Series™ Filter
ITEM DESCRIPTION
1
P/N QTY.
2
1
2
3
4
5
6
Manual Air Relief Valve Kit
Lid w/Manual Air Relief Valve Kit
Clamp Ring 2000 Knob Style
Knob, Plastic
188597
1
1
1
1
1
8
188603
072898
076033
071019
074923
074924
074925
074926
073270
071442
12
3
Holding Wheel 2000
Element 2036 - 18"
Element 2048 - 24"
Element 2060 - 30"
Element 2072 - 36"
Manifold 2000 Series - 8 Hole
O-Ring, Channel w/Red Line
Tank SM – Less Collector
SM 2036
10
11
4
7
8
9
1
1
1
5
6
073437
073438
073439
073440
SM 2048
SM 2060
SM 2072
Tank SMBW – Less Casting
SM 2036
1
1
073442
073443
073444
073445
7
8
SM 2048
SM 2060
SM 2072
10
Center Rod Kit
SM/SMBW 2036
SM/SMBW 2048
SM/SMBW 2060
SM/SMBW 2072
188598
188599
188600
188601
188596
11
12
Center Rod Hardware Kit
Includes: Washer and Wing Nut
1
1
9
Vent Tube Kit
Includes: Screen Cap and Nut
075279
Not Shown
Collector 3 Port 2" SM Series only
072901
1
Flow Rate Table
ꢀꢁꢂꢃꢄꢅ
ꢔꢒ ꢕꢃꢉꢅ
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢥ
ꢀꢁꢂꢃꢄꢅꢆꢎꢏꢥ
ꢀꢁꢂꢃꢄꢅꢆꢈꢆꢥ
ꢀꢁꢂꢃꢄꢅꢆꢌꢅꢥ
ꢆꢇꢄꢈꢃꢉꢅ
ꢖꢉꢃꢌꢅꢗꢑꢎꢅꢆꢈꢎꢅ ꢘꢄꢃꢌꢉꢌꢙꢋꢃꢚꢅ ꢍꢇꢌ ꢃꢈꢃꢉꢅ
ꢊꢃꢉꢈꢇꢋꢌꢄꢅ
ꢆꢇꢄꢈꢃꢉꢅ ꢍꢎꢏꢎꢅꢐꢃꢑꢒꢇꢉꢃꢂꢅ ꢆꢄꢁꢓꢅꢐꢌꢈꢃꢅ
6ꢒꢉꢙꢁꢟꢃꢉꢅꢘꢌꢠꢌꢋꢇꢈꢡ;ꢐꢃꢝꢎꢅ
ꢛꢜꢕꢝꢎ!ꢅ
ꢇꢋꢈ
ꢎꢋꢏ
ꢛ"#ꢀ!ꢚꢚꢅ
ꢌꢆ
ꢐꢎ
$ꢞꢉꢝꢎꢅ
ꢇꢇꢍꢈꢆꢆ
ꢎꢉꢍꢑꢅꢆ
ꢉꢉꢍꢈꢏꢆ
ꢈꢌꢍꢅꢆꢆ
'+ꢞꢉꢝꢎꢅ
ꢎꢅꢍꢆꢆꢆ
ꢉꢈꢍꢎꢆꢆ
ꢈꢐꢍꢈꢆꢆ
ꢏꢎꢍꢆꢆꢆ
'-ꢞꢉꢝꢎ
ꢉꢆꢍꢎꢆꢆ
ꢈꢌꢍꢈꢏꢆ
ꢏꢇꢍꢉꢅꢆ
ꢑꢆꢆꢍꢏꢆꢆ
ꢇꢉ
ꢎꢌ
ꢉꢏ
ꢌꢆ
ꢈꢆꢊꢄ
ꢈꢈꢊꢄ
ꢌꢅꢊꢄ
ꢌꢏꢊꢄ
ꢅꢆꢊꢄ
ꢅꢆꢊꢄ
ꢅꢆꢊꢄ
ꢅꢆꢊꢄ
ꢈ
ꢌꢋꢅ
ꢑꢑꢈ
ꢑꢎꢆ
ꢒꢄꢓꢔꢕꢖꢗꢘꢔꢙꢄꢚꢛꢔꢜꢘꢜꢝꢚꢔꢄꢞꢟꢄꢘꢔ ꢟꢠꢔꢄꢡꢗꢛꢞꢔꢘꢄꢔꢛꢔ ꢔꢝꢞꢢ
ꢒꢒꢄꢁꢜꢣꢗ ꢖ ꢄꢡꢛꢟꢤꢄꢘꢜꢞꢔ
ꢥꢄ+ꢛꢢꢟꢄꢜꢠꢜꢗꢛꢜ;ꢛꢔꢄꢤꢗꢞꢦꢟꢖꢞꢄ;ꢜꢚꢧꢤꢜꢢꢦꢄꢠꢜꢛꢠꢔ3ꢀꢁꢄ ꢟꢙꢔꢛꢢ
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Replacement Parts List
1
Rotary Valve Model SMBW w/ Noryl Rotor
2
Item Description
Valve BW w/Noryl Rotor Complete
P/N
Qty.
073462
074927
070731
071426
073370
071435
071427
072112
190026
070971
188602
1
6
1
1
1
1
1
1
1
1
1
3
1
2
3
4
5
6
7
8
9
Screw 1/4-20 x 5/8" HH s/s
Compression Ring
O-Ring 2-228 Collar & Rotor
Rotor Valve Noryl w/Tapered Seal
O-Ring Buna 2-113 Rotor Shaft
O-Ring 2-259 Valve 3 Port
Casting, Valve Body, Brass 2" Thread
Handle SMBW Rotor s/s
4
5
Handle Extension BW Brass
10 Rotor Valve Handle Hardware Kit
6
7
Includes: Bolt, Lock Washer, Nut, Spacer Washer
EFFLUENT
DRAIN
FROM PUMP
DISCHARGE
8
9
10
Head Loss Comparison Curves
PRESSURE DROP CURVES
D.E. FILTER
D.E. Filter - 2000 Series
Head Loss Curve
20
18
16
14
12
10
8
SMBW - 2036
SMBW - 2048
SMBW - 2060
SMBW - 2072
SM - 2036
SM - 2048
SM - 2060
SM - 2072
6
4
2
0
0
20
40
60
80
100
120
140
160
U.S. Gallons per Min.
SAVE THESE INSTRUCTIONS
SM/SMBW 2000 Series™ Filter Installation and User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
SM/SMBW2000
Download from Www.Somanuals.com. All Manuals Search And Download.
P/N 075122 Rev. E 4/5/06
Download from Www.Somanuals.com. All Manuals Search And Download.
|