Pelco TV Mount PDF8 Series User Manual

C1463M-A (12/00)  
PDF8 Series  
Pendant Fixed Mount Dome  
®
3500 Pelco Way  
Clovis, CA 93612-5699  
USA  
IMPORTANT SAFEGUARDS AND WARNINGS  
Prior to installation and use of this product, the following WARNINGS should be observed.  
In North America & Canada:  
Tel (800) 289-9100  
FAX (800) 289-9150  
1. Installation and servicing should only be done by qualified service personnel and conform  
to all local codes.  
DataFAX (800) 289-9108  
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclosure,  
it is designed for indoor use only and it must not be installed where exposed to rain and  
moisture.  
International Customers:  
Tel +1(559) 292-1981  
FAX +1(559) 348-1120  
DataFAX +1(559) 292-0435  
3. Only use replacement parts recommended by Pelco.  
PelcoEurope BV  
4. The installation method and materials should be capable of supporting four times the  
weight of the enclosure, pan/tilt, camera and lens combination.  
Dillenburg Center  
Dillenburgstraat 5F  
5652 AM Eindhoven  
The Netherlands  
Tel +31(40) 251-9870  
FAX +31(40) 251-9835  
Please thoroughly familiarize yourself with the information in this manual prior to installation and  
operation.  
DESCRIPTION  
Pelco Online  
PDF8 Series domes are pendant style units designed for indoor use only. The dome can be  
mounted to a ceiling or wall using a suitable length pipe (threaded at both ends) and a mount/  
adapter. All PDF8 Series pendant domes are compatible with Pelco IWM Series Wall Mount, the  
MRWA Wall Mount, and the MRCA Ceiling Mount.  
Models  
PDF8-0  
Pendant dome with opaque black bubble and smoked viewing slot (1/2 f-stop  
of light loss)  
PDF8-1  
Same as the PDF8-0 except bubble is opaque black with a clear viewing slot  
INSTALLATION  
Mount, Back Box Cap and Back Box Installation  
1
Refer to the instructions supplied with  
the IWM, MRWA, or MRCA to install the  
mount for the PDF8 Series dome. Bring  
the wiring for the dome through the  
mount. Refer to Tables A and B for wir-  
ing distances.  
NOTE: The length of pipe used  
may cause noticeable motion on  
the video display. If this occurs,  
the pipe will require additional  
support by bracing, guy wires, etc.  
MOUNT  
PIPE  
(NOT SUPPLIED)  
BACK BOX  
CAP  
CAUTION: The mount  
area must be capable of  
supporting up to 40  
2
3
Install a threaded pipe with a minimum  
length of 2.50-inches into the mount.  
Tighten the pipe to the mount with torque  
of approximately 30 ft-lb.  
pounds (18.12 kg) of weight.  
BACK BOX  
Refer to Figure 1 and install the back  
box cap and back box. Pull wiring from  
the mount through the back box cap and  
into the back box. Slide the back box  
cap over the pipe and screw the back  
box onto the threaded pipe. Tighten the  
back box by lightly applying torque, ap-  
proximately 20 ft-lb.  
Figure 1. Back Box Cap and Back Box  
Installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table A. Video Coaxial Cable Requirements  
Cable Type*  
Maximum Distance  
RG59/U  
RG6/U  
750 ft (229 m)  
1,000 ft (305 m)  
1,500 ft (457 m)  
RG11/U  
* Minimum cable requirements:  
75 ohms impedance  
All-copper center conductor  
All-copper braided shield with 95% braid coverage  
Table B. 24 VAC Wiring Distances  
The following are the recommended maximum distances for 24 VAC applications and are  
calculated with a 10-percent voltage drop. (Ten percent is generally the maximum allowable  
voltage drop for AC-powered devices.)  
Wire Gauge  
EXAMPLE: An enclosure  
that requires 80 vA and is in-  
stalled 35 feet (10 m) from  
the transformer would re-  
quire a minimum wire gauge  
of 20 AWG.  
Total  
vA  
10  
20  
18  
16  
14  
12  
10  
(0.5 mm2) (1.0 mm2) (1.5 mm2) (2.5 mm2) (4.0 mm2) (6.0 mm2)  
283  
(86)  
451  
(137)  
716  
(218)  
1142  
(348)  
1811  
(551)  
2880  
(877)  
20  
141  
(42)  
225  
(68)  
358  
(109)  
571  
905  
(275)  
1440  
(438)  
(174)  
30  
94  
(28)  
150  
(45)  
238  
(72)  
380  
(115)  
603  
(183)  
960  
(292)  
NOTE: Wire gauges are  
standard AWG or metric  
sizes. Distances are calcu-  
lated in feet; values in  
40  
70  
(21)  
112  
(34)  
179  
(54)  
285  
(86)  
452  
(137)  
720  
(219)  
50  
56  
(17)  
90  
(27)  
143  
(43)  
228  
(69)  
362  
(110)  
576  
(175)  
parentheses are meters.  
60  
47  
(14)  
75  
(22)  
119  
(36)  
190  
(57)  
301  
(91)  
480  
(146)  
70  
40  
(12)  
64  
(19)  
102  
(31)  
163  
(49)  
258  
(78)  
411  
(125)  
80  
35  
(10)  
56  
(17)  
89  
(27)  
142  
(43)  
226  
(68)  
360  
(109)  
90  
31  
(9)  
50  
(15)  
79  
(24)  
126  
(38)  
201  
(61)  
320  
(97)  
100  
110  
120  
130  
140  
150  
160  
170  
180  
190  
200  
28  
(8)  
45  
(13)  
71  
(21)  
114  
(34)  
181  
(55)  
288  
(87)  
25  
(7)  
41  
(12)  
65  
(19)  
103  
(31)  
164  
(49)  
261  
(79)  
23  
(7)  
37  
(11)  
59  
(17)  
95  
(28)  
150  
(45)  
240  
(73)  
21  
(6)  
34  
(10)  
55  
(16)  
87  
(26)  
139  
(42)  
221  
(67)  
20  
(6)  
32  
(9)  
51  
(15)  
81  
(24)  
129  
(39)  
205  
(62)  
18  
(5)  
30  
(9)  
47  
(14)  
76  
(23)  
120  
(36)  
192  
(58)  
17  
(5)  
28  
(8)  
44  
(13)  
71  
(21)  
113  
(34)  
180  
(54)  
16  
(4)  
26  
(7)  
42  
(12)  
67  
(20)  
106  
(32)  
169  
(51)  
15  
(4)  
25  
(7)  
39  
(11)  
63  
(19)  
100  
(30)  
160  
(48)  
14  
(4)  
23  
(7)  
37  
(11)  
60  
(18)  
95  
(28)  
151  
(46)  
14  
(4)  
22  
(6)  
35  
(10)  
57  
(17)  
90  
(27)  
144  
(43)  
Maximum distance from transformer to load  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
To clean the inside or outside of the plastic viewing dome, use a soft cloth that will not scratch  
the surface. If you use any liquid cleaner, make sure it is safe for acrylic plastic.  
Service Manual  
If you need to service your unit, obtain a service manual in one of the following ways:  
Call Pelco’s DataFAX service at 1-800-289-9108 or 1-559-292-0435 and request document  
214638.  
Contact Pelco’s Literature Department and request service manual C1463SM.  
SPECIFICATIONS  
GENERAL  
Environment:  
Operating Range:  
Weight:  
Indoor only  
32° to 120°F (0° to 49°C)  
8.25 lb (3.74 kg)  
MECHANICAL  
Construction  
Back Box:  
Aluminum  
Cap:  
Aluminum  
Bezel:  
Aluminum  
Viewing Window:  
Finish:  
Cable Entry:  
Dimensions:  
Maximum Camera/  
Lens Size  
Acrylic plastic  
Black polyester powder coat  
Top of dome  
See Dimension Drawing  
(Dimensions include BNC connector)  
Horizontal:  
15 degrees:  
30 degrees:  
7.0 (L) x 4.5 (W) x 3.0 (H) inches (17.78 x 11.43 x 7.62 cm)  
10.0 (L) x 4.5 (W) x 2.0 (H) inches (25.4 x 11.43 x 5.08 cm)  
12.0 (L) x 4.5 (W) x 2.5 (H) inches (30.48 x 11.43 x 6.35 cm)  
(Design and specifications are subject to change without notice.)  
WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in  
material or workmanship for a period of one year after the date of shipment. Excep-  
tions to this warranty are as noted below:  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100  
or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide  
the following information:  
Three years on Genex® Series (multiplexers, server, and keyboard).  
Two years on cameras and all standard motorized or fixed focal length lenses.  
Two years on Legacy®, Camclosure™ Camera Systems, CM6700/CM8500/  
CM9500/CM9750/CM9760 Matrix, PelcoVision®, DF5 Series and DF8 Fixed Dome  
products.  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall  
under the warranty conditions stated above, please include a written explana-  
tion with the product when returned.  
Two years on Spectra® and Esprit™, including when used in continuous motion  
applications.  
Two years on WW5700 series window wiper (excluding wiper blades).  
Six months on all pan and tilts, scanners or preset lenses used in continuous  
motion applications (that is, preset scan, tour and auto scan modes).  
Method of return shipment shall be the same or equal to the method by which  
the item was received by Pelco.  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco,  
Clovis, California. Repairs made necessary by reason of misuse, alteration, normal  
wear, or accident are not covered under this warranty.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call  
the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization num-  
ber (CA number if returned for credit, and RA number if returned for repair).  
Goods returned for repair or credit should be clearly identified with the assigned  
CA/RAnumber and freight should be prepaid.All merchandise returned for credit  
may be subject to a 20% restocking and refurbishing charge.  
Pelco assumes no risk and shall be subject to no liability for damages or loss result-  
ing from the specific use or application made of the Products. Pelco’s liability for any  
claim, whether based on breach of contract, negligence, infringement of any rights of  
any party or product liability, relating to the Products shall not exceed the price paid  
by the Dealer to Pelco for such Products. In no event will Pelco be liable for any  
special, incidental or consequential damages (including loss of use, loss of profit and  
claims of third parties) however caused, whether by the negligence of Pelco or otherwise.  
Ship freight prepaid to: Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
The above warranty provides the Dealer with specific legal rights. The Dealer may  
also have additional rights, which are subject to variation from state to state.  
REVISION HISTORY  
Manual # Date  
Comments  
Original version.  
C1463M  
6/97  
8/97  
12/00  
Revised available model numbers.  
Revised installation instructions and illustrations. Updated manual to new format.  
C1463M-A  
® Pelco, the Pelco logo, Spectra, Genex, Legacy, and PelcoVision are registered trademarks of Pelco.  
™ Esprit and Camclosure are trademarks of Pelco.  
© Copyright 2000, Pelco.  
All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips Electric Toothbrush HX3300 User Manual
Philips Gas Grill 32 9544 User Manual
Philips Indoor Furnishings 22FDF6023 User Manual
Philips Network Card SWV3458W 27 User Manual
Philips Portable DVD Player PET825 05 User Manual
Philips Universal Remote VR 675 User Manual
Poulan Snow Blower 421895 User Manual
Poulan Trimmer 545137282 User Manual
ProForm Home Gym PFEVEL29010 User Manual
ProMounts TV Mount UAPRO100 User Manual