Pelco Switch CM8500 User Manual

®
Breakout Panels for  
VA6000 Series Switcher  
and CM8500 Matrix System  
Installation/Operation  
Manual C842M (9/96)  
PELCO • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981  
FAX (800) 289-9150 or (1-559) 292-3827  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION/OPERATION MANUAL  
BREAKOUT PANELS FOR  
VA6000 SERIES SWITCHER AND  
CM8500 MATRIX SYSTEM  
1.0 WARNINGS  
Priortoinstallationanduseofthisproduct,thefollowing  
WARNINGS should be observed.  
1. Installation and servicing should only be done by  
Qualified Service Personnel and conform to all  
Local codes.  
2. Unless the unit is specifically marked as a NEMA  
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is  
designed for indoor use only and it must not be  
installed where exposed to rain and moisture.  
3. OnlyusereplacementpartsrecommendedbyPelco.  
This product may bear the following marks:  
This symbol indicates that dangerous voltage  
constituting a risk of electric shock is present  
within this unit.  
This symbol indicates that there are important  
operating and maintenance instructions in the  
literature accompanying this unit.  
CAUTION:  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
CAUTION:  
TOREDUCETHERISKOFELECTRICAL  
SHOCK, DO NOT REMOVE COVER. NO  
USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
Please thoroughly familiarize yourself with the information in this manual  
prior to installation and operation.  
Pelco Manual C842M (9/96)  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.0 SCOPE  
As was the case for the VA6000, all telescoped inputs  
for breakout panels used with the CM8500 are con-  
nected via the appropriate onboard header to existing  
“D” type connectors on the rear of the CM8500 Matrix  
bay via ribbon cables.  
The information contained within this manual covers  
the installation and operation of the Alarm Breakout  
Panels for the VA6000 Series Switcher and the Alarm,  
Wiretron and Relay Breakout Panels for the CM8500  
Matrix system.  
The 24 inch (.609 m) and 120 inch (3.048 m) length  
ribbon cable assemblies for the 40-pin header type con-  
nectors have the same configuration and can be used  
with either the Wiretron Breakout Panel or the Alarm  
Breakout Panel.  
3.0 DESCRIPTION  
VA6000  
The Breakout Panels for the VA6000 Series provide a  
convenient method for physically telescoping up to 20  
alarm inputs down into the most appropriate of two  
headers existing on the Alarm Breakout Panel board  
for convenient connection to “D” type connectors on  
the rear of the VA6000.  
The ribbon cable used with the 50-pin header (also avail-  
able in the same lengths) is used only with the Relay  
Breakout Panel for the CM8500 system. Reference  
Table II, Figure 12 as a guide for ordering information  
related to CM8500 breakout panels while referencing  
other appropriate figures in the manual.  
A ribbon cable connects one of the two available header  
types (15-pin or 25-pin header) to the appropriate “D”  
type connector, depending on alarm input population,  
on the rear of the VA6000. Basically, two classes of rib-  
bon cable are available: one for use with 4 and 8 alarm  
input models and another for 12 or 20 alarm input mod-  
els. Cables are further differentiated by length–24 inch  
(.609 m) or 120 inch (3.048 m) lengths are available.  
NOTE: When working with a CM8500 Ma-  
trix System, additional subassemblies may be  
required (if not already installed) on the  
CM8500 side of the installation in order to uti-  
lize the Alarm, Wiretron and Relay connectors  
on the rear of the CM8500 Matrix bay. These  
are:  
CM8506 Communication circuit card to al-  
low the CM8500 to communicate  
with Wiretron receiver/drivers.  
Mounts to Buffer Card.  
CM8532 32 alarm/32 relay circuit card kit  
to allow for direct monitoring of  
32 alarms and the use of 32 relay  
outputs programmable in software.  
Additionally, each breakout panel assembly is shipped  
from the factory installed on a single mounting plate  
with appropriate mounting hardware. You should auto-  
matically receive the correct breakout panel, ribbon  
cable, mounting plate and hardware if you use Table 1  
in Figure 12 as a guide while referencing all other ap-  
propriate figures provided in the manual.  
CM8500  
Consult your CM8500 manual (C501M) for in-  
stallation requirements and any related infor-  
mation, if needed.  
The Breakout Panels for the CM8500 Matrix System  
likewise provide a convenient method for physically  
telescopingAlarm, Wiretron or Relay inputs down into  
appropriate headers for eventual connection to “D” type  
subconnectors on the rear of the CM8500 Matrix bay.  
4.0 INSTALLATION  
Breakout panels come from the factory installed on  
single mounting plates; an appropriate ribbon cable is  
included with the assembly. The Breakout panel and  
plate can be mounted in any convenient, accessible lo-  
cation. Once mounted, all user supplied wiring inputs  
(alarm, wiretron or relay) can be connected and then  
the supplied ribbon cable can be run between the header  
on the breakout panel and the appropriate “D” type con-  
nector on the equipment being used, whether VA6000  
or CM8500.  
Unlike the VA6000 which is populated with two head-  
ers, each with different pin-outs on one breakout panel,  
the CM8500 utilizes three different breakout panels  
populated with only one header, with header pin-out  
configurations for the type of breakout panel being used:  
Alarm, Wiretron or Relay. For the CM8500, Breakout  
panels for Alarm and Wiretron inputs utilize, in each  
case, a single 40-pin header, while Relay Breakout pan-  
els incorporate a single 50-pin header.  
Once the panels are physically mounted and all wires  
and cables are run, the product is ready for use.  
2
Pelco Manual C842M (9/96)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 1. Alarm Breakout Panel Assembly Information–VA6000 Series  
Pelco Manual C842M (9/96)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
The table below lists the pin-out relationship between the alarm panel header, J2, and the 15-pin connec-  
tor on the rear of the VA6000 switcher for 8 input alarms. The pattern serves equally well for VA models  
with 4 input alarms: the first 4 Pin Numbers correspond to like numbered ALM numbers, with pins 5-10  
unused and pins 11-15 serving the same functions as in the 8 input VA6000 Switcher model.  
J2 Header Pin-out on Alarm Breakout  
for VA6000  
Alarm Pin-outs 1-8/VA6000  
Rear Panel Connector  
15-Pin Female Conn. on Switcher  
Pin Numbers  
Pin Numbers  
ALM #  
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
3
5
7
9
11  
13  
15  
not used  
not used  
9
2 (not used)  
4 (not used)  
6
8
10  
12  
14  
10  
11  
12  
13  
14  
15  
K1 - NO  
K1 -COM  
K1 - NC  
Ext.Trig.  
Comm  
Figure 2. Installation Configuration and Pin Mapping for 4/8 Alarm Inputs-VA6000 Alarm Breakout Panel  
4
Pelco Manual C842M (9/96)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The table below lists the pin-out relationship between the alarm panel header, J1, and the 25-pin con-  
nector on the rear of the VA6000 switcher for 20 input alarms. The pattern serves equally well for VA  
models with 12 input alarms: the first 12 Pin Numbers correspond to like numbered ALM numbers  
with pins 13-20 unused and pins 21-25 serving the same functions as in the 20 input VA6000 Switcher  
models.  
J1 Header Pin-out on Alarm Breakout  
for CM8500  
Alarm Pin-outs 1-16/CM8500 Rear Panel-P4  
ALM #  
25-Pin Female Conn. on Switcher  
Pin Number  
Pin Number  
1
1
1
2
2
3
3
3
5
4
4
7
5
5
9
6
7
8
9
6
7
8
9
11  
13  
15  
17  
19  
21  
23  
25  
2
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
4
6
8
10  
12  
14  
16  
18  
20  
22  
24  
K1 - NO  
K1 -COM  
K1 - NC  
Ext.Trig.  
Comm  
Figure 3. Installation Configuration and Pin Mapping for 12/20 Alarm Inputs-VA6000 Alarm Breakout Panel  
Pelco Manual C842M (9/96)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 4. Alarm Breakout Panel Assembly Information–CM8500 Series  
6
Pelco Manual C842M (9/96)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The table below lists the pin-out relationship between the alarm panel header, J1, and P4 on the CM8500  
for the first 16 alarms. The pattern serves equally well for alarms 17-32: P4 becomes P3 and the listed  
alarms go from 17-32 instead of 1-16.  
J1 Header Pin-out on Alarm Breakout  
for CM8500  
Alarm Pin-outs 1-16/CM8500 Rear Panel-P4  
ALM #  
Pin Number  
Com  
Pin Number  
Alarm  
1
1
...  
1
...  
2
20  
...  
2
3
2
...  
3
21  
...  
4
5
3
...  
4
22  
...  
6
7
4
...  
5
23  
...  
8
9
5
...  
6
...  
7
...  
8
...  
9
...  
10  
...  
11  
...  
12  
...  
13  
...  
14  
...  
15  
...  
16  
24  
...  
25  
...  
26  
...  
27  
...  
28  
...  
29  
...  
30  
...  
31  
...  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
32  
...  
33  
...  
34  
...  
...  
35  
32  
Figure 5. Installation Configuration and Pin Mapping for the CM8500 Alarm Breakout Panel  
Pelco Manual C842M (9/96)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 6. Wiretron Breakout Panel Assembly Information–CM8500 Series  
8
Pelco Manual C842M (9/96)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The table below lists the pin-out relationship between the wiretron panel header, J1, and P5 on the  
CM8500 for the first 16 wire control positions. The pin mappings serve equally well for wire controls  
17-32: P5 becomes P6 and the listed WIR numbers go from 17-32 instead of 1-16.  
J1 Header Pin-out on Wiretron Breakout  
Panel for CM8500  
Wire Control Pin-outs 1-16/CM8500  
Rear Panel-P5  
WIR #  
Pin Number  
Pin Number  
1
1
...  
3
...  
5
...  
7
...  
2
...  
4
...  
6
...  
8
1
3
5
7
2
3
9
11  
13  
15  
17  
19  
21  
23  
25  
27  
29  
31  
2
4
...  
9
5
...  
10  
...  
12  
...  
14  
...  
16  
...  
21  
...  
23  
...  
25  
...  
27  
...  
29  
...  
318  
...  
33  
...  
...  
11  
...  
13  
...  
15  
...  
20  
...  
22  
...  
24  
...  
26  
...  
28  
...  
30  
...  
32  
...  
34  
6
7
8
9
4
6
8
10  
11  
12  
13  
14  
15  
16  
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
30  
...  
35  
32  
Figure 7. Installation Configuration and Pin Mapping for the CM8500 Wiretron Breakout Panel  
Pelco Manual C842M (9/96)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 8. Wiretron Breakout Panel Assembly Information–CM8500 Series  
10  
Pelco Manual C842M (9/96)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 9. Installation Configuration for the CM8500 Wiretron Breakout Panel  
Figure 10. Rack Panel Mounting Plate Dimensions  
Pelco Manual C842M (9/96)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The table below lists the pin-out relationship between the relay panel header, J1, and P1 on the CM8500  
for the first 16 relay output positions. The pin mappings serve equally well for relay outputs 17-32: P1  
becomes P2 and the listed RELAY numbers go from 17-32 instead of 1-16.  
J1 Header Pin-out on Relay  
Breakout Panel for CM8500  
Pin Number  
Relay 1-16 Pin-outs CM8500  
Rear Panel-P1  
RELAY #  
Pin Number  
NO  
NC  
COM  
1
...  
2
...  
...  
5
...  
...  
8
...  
...  
3
...  
...  
6
...  
...  
9
1
2
3
4
5
6
7
8
1
...  
...  
4
...  
...  
7
2
3
...  
...  
10  
...  
...  
13.  
...  
...  
16  
...  
...  
19  
...  
...  
22  
...  
...  
25  
...  
...  
28  
...  
...  
31  
...  
...  
34  
...  
...  
37  
...  
...  
40  
...  
...  
43  
...  
...  
46  
...  
...  
...  
11  
...  
...  
14  
...  
...  
17  
...  
...  
20  
...  
...  
23  
...  
...  
26  
...  
...  
29  
...  
...  
32  
...  
...  
35  
...  
...  
38  
...  
...  
41  
...  
...  
44  
...  
...  
47  
9
...  
...  
12  
...  
...  
15  
...  
...  
18  
...  
...  
21  
...  
...  
24  
...  
...  
27  
...  
...  
30  
...  
...  
33  
...  
...  
36  
...  
...  
39  
...  
...  
42  
...  
...  
45  
...  
...  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
...  
...  
48  
48  
Figure 11. Pin Mapping for the CM8500 Relay Breakout Panel  
12  
Pelco Manual C842M (9/96)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.0 MODELS  
CM8500-WPNL-2 Wiretron breakout panel for up  
to 16 outputs/panel; 2-foot (.609  
m) inter connecting ribbon cable  
supplied.  
VA6008-APNL-2  
VA6000 alarm breakout panel  
for up to 8 alarm inputs; 2-foot  
(.609 m) interconnecting ribbon  
cable supplied.  
CM8500-WPNL-10 Same as CM8500-WPNL-2, ex-  
cept 10-foot (3.048 m) intercon-  
VA6008-APNL-10 Same as VA6008-APNL-2, ex-  
cept 10-foot (3.048 m) intercon-  
necting ribbon cable.  
necting ribbon cable.  
CM8500-RPNL-2 Relaybreakoutpanelforupto16  
outputs/panel;2-foot(.609m)in-  
terconnecting ribbon cable sup-  
plied.  
VA6020-APNL-2  
VA6000 alarm breakout panel  
for up to 20 alarm inputs; 2-foot  
(.609 m) interconnecting ribbon  
cable supplied.  
CM8500-RPNL-10 Same as CM8500-RPNL-2, ex-  
cept 10 foot (3.048 m) intercon-  
VA6020-APNL-10 Same as VA6020-APNL-2 ex-  
cept 10-foot (3.048 m) intercon-  
necting ribbon cable.  
6.0 OPTIONAL ACCESSORIES  
necting ribbon cable.  
RK-1PNL  
Rack kit for mounting one  
breakout panel (see Figure 10).  
CM8500-APNL-2 Alarm breakout panel for up to  
16 alarm inputs/panel; 2-foot  
(.609 m) interconnecting ribbon  
cable supplied.  
RK-4PNL  
Rack kit for mounting up to four  
breakout panels (see Figure 10).  
CM8500-APNL-10 Same as CM8500-APNL-2, ex-  
cept 10-foot (3.048 m) intercon-  
necting ribbon cable.  
Table I. Alarm Breakout Panel Assembly Part Numbers for VA6000 Series Switchers  
# Of Inputs  
4 or 8 Alarm Inputs  
VA6008-APNL-2  
VA6008-APNL-10  
12 or 20 Alarm Inputs  
VA6020-APNL-2  
VA6020-APNL-10  
Cable Length  
24 in (.609 m)  
cable  
120 in (3.048 m)  
cable  
Table II. Breakout Panel Assembly Part Numbers for CM8500 Matrix System  
Input Type  
Alarm Inputs  
Wiretron Control Outputs  
Relay Outputs  
CM8500-RPNL-2  
CM8500-RPNL-10  
Cable Length  
24 in (.609 m)  
cable  
CM8500-APNL-2  
CM8500-WPNL-2  
120 in (3.048 m)  
cable  
CM8500-APNL-10 CM8500-WPNL-10  
Figure 12. Simplified Part Number Ordering Tables  
Pelco Manual C842M (9/96)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7.0 WARRANTY AND RETURN INFORMATION  
WARRANTY  
RETURNS  
Pelco will repair or replace, without charge, any merchandise proved  
defectiveinmaterialorworkmanshipforaperiodofoneyearafterthedate  
of shipment.  
In order to expedite parts returned to the factory for repair or credit, please  
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an  
authorization number (CA number if returned for credit, and RA number  
if returned for repair).  
Exceptions to this warranty are as noted below:  
All merchandise returned for credit may be subject to a 20% restocking  
and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the  
assigned CA or RA number and freight should be prepaid. Ship to the  
appropriate address below.  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and  
keyboard).  
Three years on Camclosure® and fixed camera models, except the  
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,  
and MC3651H-2X camera models, which have a five-year warranty.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto  
Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto  
Rico and are instructed to return goods to the USA, you may do one of the  
following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and  
DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, includ-  
ing when used in continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding  
wiper blades).  
Eighteen months on DX Series digital video recorders, NVR300  
Series network video recorders, and EnduraSeries distributed  
network-based video products.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
One year (except video heads) on video cassette recorders (VCRs).  
Video heads will be covered for a period of six months.  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods  
to:  
Six months on all pan and tilts, scanners or preset lenses used in  
continuousmotionapplications(thatis,presetscan,tourandautoscan  
modes).  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
Pelco will warrant all replacement parts and repairs for 90 days from the  
date of Pelco shipment. All goods requiring warranty repair shall be sent  
freight prepaid to Pelco, Clovis, California. Repairs made necessary by  
reason of misuse, alteration, normal wear, or accident are not covered  
under this warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or  
loss resulting from the specific use or application made of the Products.  
Pelco’s liability for any claim, whether based on breach of contract,  
negligence, infringement of any rights of any party or product liability,  
relating to the Products shall not exceed the price paid by the Dealer to  
Pelco for such Products. In no event will Pelco be liable for any special,  
incidental or consequential damages (including loss of use, loss of profit  
and claims of third parties) however caused, whether by the negligence  
of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The  
Dealer may also have additional rights, which are subject to variation from  
state to state.  
Ifawarrantyrepairisrequired,theDealermustcontactPelcoat(800) 289-  
9100 or (559) 292-1981 to obtain a Repair Authorization number (RA),  
and provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice  
number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall  
under the warranty conditions stated above, please include a written  
explanation with the product when returned.  
Method of return shipment shall be the same or equal to the method by  
which the item was received by Pelco.  
Pelco  
3500 Pelco Way, Clovis, CA 93612-5699 (559)  
292-1981 • (800) 289-9100  
FAX (800) 289-9150 or (559) 292-3827  
International customers call 1-559-292-1981 or  
FAX 1-559-348-1120  
(Product specifications subject to change  
without notice.)  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and  
Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
C842M  
© Copyright 1996, Pelco. All rights reserved.  
14  
Pelco Manual C842M (9/96)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pentair Network Card SunTouch User Manual
Perlick Freezer F24N User Manual
Philips Battery Charger SCB2000NB User Manual
Philips Clock Radio AJ3121 05 User Manual
Philips Indoor Furnishings TableLights User Manual
Philips Network Cables SWV3432S User Manual
Pioneer CD Player DEH 200MP User Manual
Pioneer Stereo System VSX 819H User Manual
ProForm Home Gym PFB38030 User Manual
ProScan Flat Panel Television PLEDV2213A User Manual