Pelco Security Camera MCC2400 User Manual

CCC2400/MCC2400 SERIES COMPACT CAMERAS  
INSTALLATION/OPERATION  
IMPORTANT SAFEGUARDSAND WARNINGS  
MODELS  
CCC2400S-4 Standard resolution (330 TV lines) color camera, 1.0 lux  
at f1.2, NTSC  
Prior to installation and use of the product, the following WARNINGS  
should be observed.  
CCC2400S-4X Standard resolution (330 TV lines) color camera, 1.0 lux  
at f1.2, PAL  
1. Installation and servicing should be done only by qualified service  
personnel and conform to all local codes.  
CCC2400H-4 High resolution (470 TV lines) color camera, 1.2 lux at  
f1.2, NTSC  
2. Power camera only from a UL Listed, Class 2 isolated power supply.  
CCC2400H-4X High resolution (470 TV lines) color camera, 1.2 lux at  
f1.2, PAL  
3. Do not touch the image surface of the sensor. If the sensor is  
accidentally touched, clean it only with isopropanol.  
MCC2400S-4 Standard resolution (380 TV lines) monochrome camera,  
0.1 lux at f1.2, EIA  
4. Do not expose the camera sensor to very bright light over a long  
period of time as this may damage the CCD. The camera and lens  
setup must be correct to avoid continual overexposure to bright light.  
A lens with an automatic iris is recommended under these conditions.  
MCC2400S-4X Standard resolution (380 TV lines) monochrome camera,  
0.1 lux at f1.2, CCIR  
5. Before installing the lens, make sure that its back will not touch the  
CCD sensor or associated components when it is screwed into the  
camera.  
CAMERALAYOUT  
Refer to Figure 1.  
6. For outdoor use, an appropriate protective housing conforming to  
IP65 or UL50 or better must be used.  
AUTO IRIS LENS CONNECTOR  
The maximum load must not exceed 50 mA  
REGULATORYNOTICES  
This device complies with part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) This device may not cause harmful  
interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
This equipment has been tested and found to comply with the limits of a  
Class B digital device, pursuant to part 15 of the FCC rules. These limits  
are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses,  
and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to  
radio communications. However there is no guarantee that the  
interference will not occur in a particular installation. If this equipment  
does cause harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the user is  
encouraged to try and correct the interference by one or more of the  
following measures:  
Figure 1. Location of Parts  
Auto Iris Lens Connector (DC drive only)  
Camera Mounts  
Reorient or relocate the receiving antenna.  
Lens Level Adjustment  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
Lens Mount/Back Focus Adjustment Ring  
Electronic Shutter Control (ESC) Switch  
Back Focus Locking Screw (on the side of the camera)  
Power Input Terminals  
Consult the dealer or an experienced radio/TV technician for help.  
Any changes or modifications not expressly approved by the party  
responsible for compliance could void the user’s authority to operate  
the equipment.  
Backlight Compensation Switch  
Video Output Connector  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003  
du Canada.  
INSTALLATION  
1. The camera accepts a CS-mount lens with a fixed iris, manual iris, or  
direct drive auto iris. A C-mount lens can be used but requires Pelco’s  
PCMA40 C-mount adapter. Screw the lens into the camera. For a  
direct drive auto iris lens, connect the four-pin plug to the auto iris  
lens connector on the camera.  
DESCRIPTION  
The CCC2400 Series and the MCC2400 Series comprise color or  
monochrome cameras with 1/3-inch CCD imagers and a direct drive  
lens connector. All cameras accept CS lenses; C lenses can be used  
but require Pelco’s PCMA40 C-mount adapter. Color cameras have digital  
signal processing (DSP) and auto white balance.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco Computer Accessories C2904M B User Manual
Pelco Computer Monitor pmc14f User Manual
Pelonis Electric Heater HC 0113 User Manual
Philips Baby Monitor SCD491 User Manual
Philips CD Player CDR 600 17 User Manual
Philips Work Light T22 B15d User Manual
Pioneer Car Stereo System AVIC 80DVD User Manual
Pitco Frialator Fryer 12 User Manual
Planar Car Video System PX2611W User Manual
Profoto Camera Accessories PRO 8A 1200 AIR User Manual