Pelco Security Camera C1969M A User Manual

®
CCQ1400A-4  
Color CCD Camera  
with 4 mm Lens  
Installation/  
Operation Manual  
C1969M-A (1/02)  
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com  
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150  
International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DESCRIPTION  
OVERVIEW  
The CCQ1400A-4 color CCD camera with 4 mm lens is designed for use with the PMCQ14A 14-inch color quad monitor.  
A mini-DIN 6 connector in the back of the camera matches the connector on the back of the monitor. Power, alarm, audio and video  
contacts are all provided at this connector.  
MODELS  
CCQ1400A-KIT  
Camera assembly with audio, consisting of one CCQ1400A-4 camera, one WMQ8 bracket and one  
CCQCABLE-60 cable.  
CCQ1400A-4  
1/4-inch color CCD camera with 4 mm lens, 12 VDC, with a microphone and speaker  
INSTALLATION  
INSTALLATION TIPS  
NO STAPLES  
NO SHARP BENDS  
• Do not locate components or cable where they will get wet.  
• Lay cable loosely in attic or under floor.  
• Do not tightly bundle with other wires.  
• Avoid sharp bends in the cable.  
• Do not directly staple the cable to any surface.  
• Try to locate cable away from power lines and fluorescent fixtures.  
• If a power line or fixture is in the way, take the cable across it at right angles.  
• Do not run cables parallel to fixtures or power lines.  
STORE EXTRA CABLE  
SERPENTINE FASHION  
CROSS AC POWER LINES AND FLORESCENT  
FIXTURES AT RIGHT ANGLES  
• The cable is 60 feet long. Do not try to shorten it.  
• Extra cable should be spread out serpentine style.  
• Avoid coiling up extra cable.  
AC  
VIDEO  
UNPACKING  
The camera is shipped as a camera only or as a kit. Unpack and inspect the contents carefully.  
Camera Kit  
Camera Only  
1 Camera  
1
1
1
1
Camera  
Camera bracket  
Camera bracket base  
Cable  
Pelco Manual C1969M-A (1/02)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLING THE CAMERA  
1. Assemble and mount the camera and bracket.  
CAMERA  
NOTE: The screws provided are intended for wood. If it is necessary to substitute  
screws for masonry or hollow wall mounting, be sure to use #6 or 4 mm hardware.  
BALL JOINT  
2. Run cables. Refer to Installation Tips.  
THUMB NUT  
SET SCREW  
BRACKET  
MICROPHONE  
MIC  
MIC  
ALARM  
IN GND  
ALARM  
IN GND  
MONITOR  
MONITOR  
THUMB NUT  
SET SCREW  
BRACKET BASE  
20103  
20106  
20105  
3. Connect cable to camera. Insert plug with the arrow facing up.  
4. Connect alarm contacts, if used.  
MIC  
ALARM  
IN GND  
MONITOR  
5. Connect cable to one of the CH IN jacks on the back of the monitor  
(refer to Figure 1).  
20107  
6. Set impedance switch to the 75-ohm position,unless another video  
device is connected to the IN/OUT jacks (refer to Figure 1).  
N.C. OR N.O. CONTACT  
7. Connect AC power to monitor (refer to Figure 1).  
8. Turn on MAIN switch on the back of the monitor (refer to Figure 1). Then press the POWER button on the front of the monitor.  
9. Test according to the checkout procedure in Table A.  
CAMERA 1  
CAMERA 2  
CAMERA 3  
CAMERA 4  
75  
Hi 75  
Hi 75  
Hi 75  
Hi 75  
Hi  
TO VCR (WHEN AUDIO  
IS NOT USED)  
MAIN  
VIDEO AUDIO  
IN  
IN  
MONITOR  
OUT  
CH 1  
CH 2  
CH 3  
CH 4  
OUT  
IN/OUT  
A/C INLET  
FOCUS  
REMOTE*  
SCREEN  
CH 1 CH 2 CH 3 CH 4 TRIG  
OUT  
TO VCR (OPTIONAL)  
IF AUDIO IS USED  
TO VCR  
TRIGGER  
TO AC  
OUTLET  
ALTERNATE ALARM CONTACT  
(WHEN CONTACTS ON THE  
CAMERA ARE NOT USED)  
*NOT USED I
Figure 1. Connections at the Back of the Monitor  
4
Pelco Manual C1969M-A (1/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHECKOUT  
Table A. Checkout Procedure When Adding a Camera to the System  
This procedure assumes that power is on and that the full monitor checkout has been performed.  
STEP  
PROCEDURE  
Calibrate camera.  
RESULTS  
1
The CCQ1400A-4 camera is factory set for back focus.  
No further calibration is needed.  
2
3
At the monitor, press the CH button for the channel  
the new camera is using.  
See camera image full screen.  
Press the ZOOM/FREEZE button.  
Use arrow keys to move the highlighted area.  
Press the QUAD/MENU button.  
Zoom area is highlighted in the center of the screen.  
The highlighted area moves to different parts of the screen.  
The image zooms to show the selected area full screen.  
See the selected channel image full screen (normal).  
Press the QUAD/MENU or the ZOOM/FREEZE button.  
4
5
Put an object in the area being observed by the  
camera.  
While holding the RESET/ALT button, press the  
ZOOM/FREEZE button.  
Remove the object from the observed area.  
Press the ALT + FREEZE button.  
See the object on the screen. Any movement will be seen.  
See the object frozen on the screen. No movement will be  
seen.  
The object remains on the screen.  
The object disappears and movement is once again seen.  
Perform this step if the camera is equipped for the  
audio function.  
Have a person stand near the camera and speak.  
Increase the volume control on the monitor,  
if necessary.  
Hear the person at the camera speaking.  
Press and hold the AUDIO/TALK button on the  
monitor.  
Talk in a normal voice.  
The person at the camera should hear you.  
Release the AUDIO/TALK button.  
Hear the person or other sounds near the camera.  
6
7
Perform this step if the alarm contacts are  
connected to a detection switch.  
Momentarily activate the alarm contacts.  
Press the RESET button on the front of the monitor.  
ALM flashes at the top of the monitor screen.  
ALM goes away.  
Checkout is complete.  
Pelco Manual C1969M-A (1/02)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
TECHNICAL SPECIFICATIONS  
ELECTRICAL  
Input Voltage:  
12 VDC, +/-2 VDC  
Power  
Consumption:  
2 watts  
NTSC  
Signal Format:  
Scanning System: 2:1 interlace  
Sync System:  
Internal  
Horizontal  
Resolution:  
330 TV lines (center)  
Image Size Area: 4.57 mm (H) x 3.90 mm (V)  
Picture Elements: 512 (H) x 492 (V)  
Electronic Iris:  
Video Output:  
Auto White Bal.:  
1/60 to 1/100,000 second  
1.0 Vp-p, +/-10%, 75 ohms  
Electronic auto tracking  
Minimum  
Illumination:  
0.9 lux at 30 IRE, f1.2  
GENERAL  
Lens:  
C/CS Mount, F2.0, 4 mm lens  
Dimensions:  
Weight:  
2.00 (W) x 4.00 (L) x 2.38 (H) inches (5.08 x 10.16 x 6.05 cm)  
0.5 lb (0.22 kg)  
ENVIRONMENTAL  
Operating Temp.: 14° to 131°F (-10° to 55°C)  
Storage Temp.:  
Humidity  
4° to 158°F (-20° to 70°C)  
35% to 80%, non-condensing  
(Design and product specifications subject to change without notice.)  
THE FOLLOWING PAGE MAY BE COPIED.  
6
Pelco Manual C1969M-A (1/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REGULATORY NOTICES  
Note: This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC  
rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a  
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a  
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own  
expense.  
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If  
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
1. Model and serial number  
Exceptions to this warranty are as noted below:  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelcos liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
REVISION HISTORY  
Manual # Date  
Comments  
C1969M  
2/00  
1/02  
Original version.  
C1969M-A  
Revised camera drawings because of redesign. Added specification for minimum illumination. Removed models without  
audio.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
©Copyright 2002, Pelco.  
All rights reserved.  
8
Pelco Manual C1969M-A (1/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco DVR DX8100 EXP User Manual
Philips Cell Phone TCD138 User Manual
Philips Iron GC4411 User Manual
Philips Speaker System MCM238 User Manual
Philips Universal Remote SRU4105WM 17 User Manual
Pioneer DVD Player DVD 204 User Manual
Pioneer Flat Panel Television PDP 6020FD User Manual
Planon System Solutions Scanner RC805 User Manual
Polaroid Digital Camera i735 User Manual
Polycom IP Phone Soundpoint IP 550 User Manual