C785M-A (1/09)
3 Megapixel Lenses
Installation/Operation
Important Safety Instructions
WARNINGS: Prior to installation and use of this product, the following items should be observed.
•
•
Servicing should be done only by qualified service personnel.
Only use replacement parts recommended by Pelco.
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.
Description
These lenses are varifocal lenses designed for 1/3-inch megapixel cameras with 3 megapixels (MPx) or less in resolution. These lenses, which were
designed for CS-mount cameras, produce high precision images from the image center to the image corner, fully exploiting the performance of megapixel
cameras. Megapixel lenses are best suited for high-quality image surveillance with a megapixel camera as well as with a standard definition camera.
MODELS
13M2.2-6
13M2.8-8
13M2.8-12
13M15-50
1/3-inch megapixel, varifocal lens; 2.2~6.0 mm; f/1.3~2.0 auto iris; CS mount
1/3-inch megapixel, varifocal lens; 2.8~8.0 mm; f/1.2~1.9 auto iris; CS mount
1/3-inch megapixel, varifocal lens; 2.8~12.0 mm; f/1.4~2.7 auto iris; CS mount
1/3-inch megapixel, varifocal lens; 15~50.0 mm; f/1.5~2.1 auto iris; CS mount
Installation
1. Press the threaded portion of the lens mount against the threaded portion of the camera mount.
2. Slowly rotate the lens clockwise.
3. Screw in the lens mount.
4. Connect the auto iris lens cable to the electrical connector on the camera.
NOTE: The lens mount is equipped with a slip mechanism. To change the rotational position of the lens, rotate the lens until it reaches the stop (cannot be
rotated further), and then rotate it counterclockwise to the required position.
CONNECTOR
4-PIN PLUG
LENS
OPEN
OPEN
3
4
DRIVE COIL
2
1
DAMP. COIL
NOTE: The iris control for this lens cannot be activated with a video signal.
Use a camera that can send a DC signal.
Figure 1. Lens and Connector Wiring
Download from Www.Somanuals.com. All Manuals Search And Download.
Routine Servicing
A special coating has been applied to the lens surface to prevent light reflection. A dirty lens surface due to dust, oil, or fingerprints causes harmful glare,
which degrades the lens properties. Dirt can also cause mold or scratches on the lens.
NOTE: Be careful not to damage the lens while cleaning.
To remove dust, brush or dust off the lens with an oil-free soft brush or blower brush (for photography use).
To remove oil, fingerprints, or water drops:
1. Apply alcohol or lens cleaning liquid to a clean, soft, oil-free cotton cloth or lens cleaning paper. Using a spiral motion, moving from the center of the
lens to the rim, gently wipe the lens.
2. With another clean soft cloth, gently wipe off the rest of the dirt, and then dry the lens surface.
3. Repeat this process as necessary until the lens is completely clean.
Specifications
13M2.2-6
Varifocal
1/3-inch
CS mount
2.2~6.0 mm
2.7X
13M2.8-8
Varifocal
1/3-inch
CS mount
2.8~8.0 mm
2.8X
13M2.8-12
Varifocal
1/3-inch
CS mount
2.8~12.0 mm
4.3X
13M15-50
Varifocal
1/3-inch
CS mount
15.0~50.0 mm
3.3X
Type
Format Size
Mount
Focal Length
Zoom Ratio
F-number (iris fully opened)
Image Size
Flange Focal Length
Minimum Object Distance
Iris
1.3~2.0
1.2~1.9
1.4~2.7
1.5~2.2
6 mm diameter
12.5 mm
0.3 m
6 mm diameter
12.5 mm
0.3 m
6 mm diameter
12.5 mm
0.3 m
6 mm diameter
12.5 mm
0.8 m
Auto
Auto
Auto
Auto
Field of View
Wide
Vertical
Horizontal
Diagonal
92°
120°
146°
74°
100°
128°
74°
100°
127°
14°
18°
23°
Tele
Vertical
35°
26°
18°
4.2°
Horizontal
Diagonal
47°
58°
35°
44°
23°
29°
5.6°
6.9°
Focus
Zoom
Manual
Manual
Manual
Manual
Manual
Manual
Manual
Manual
Operating Temperature
14° to 122°F
(-10° to 50°C)
14° to 122°F
(-10° to 50°C)
14° to 122°F
(-10° to 50°C)
14° to 122°F
(-10° to 50°C)
Storage Temperature
-4° to 140°F
(-20° to 60°C)
-4° to 140°F
(-20° to 60°C)
-4° to 140°F
(-20° to 60°C)
-4° to 140°F
(-20° to 60°C)
Relative Humidity
Iris Drive Coil Resistance
Iris Damping Coil Resistance
Maximum Iris Operating Current
Height
Diameter
Length
Unit Weight (approximate)
35% to 90%
190 Ω 10%
500 Ω 10%
23 mA at 4 VDC
1.79 in. (4.55 cm)
1.48 in. (3.75 cm)
2.13 in. (5.40 cm)
0.12 lb (0.05 kg)
35% to 90%
190 Ω 10%
500 Ω 10%
23 mA at 4 VDC
1.79 in. (4.55 cm)
1.48 in. (3.75 cm)
2.05 in. (5.20 cm)
0.11 lb (0.05 kg)
35% to 90%
190 Ω 10%
500 Ω 10%
23 mA at 4 VDC
1.97 in. (5.00 cm)
1.80 in. (4.57 cm)
2.58 in. (6.55 cm)
0.13 lb (0.06 kg)
35% to 90%
190 Ω 10%
500 Ω 10%
23 mA at 4 VDC
1.79 in. (4.55 cm)
1.48 in. (3.75 cm)
2.30 in. (5.85 cm)
0.13 lb (0.06 kg)
NOTE: When power is turned off, the iris will close automatically.
(Design and product specifications subject to change without notice.)
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one year after the date of shipment.
Pelco will warrant all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid
to a Pelco designated location. Repairs made necessary by reason of misuse,
alteration, normal wear, or accident are not covered under this warranty.
Exceptions to this warranty are as noted below:
• Five years:
Pelco assumes no risk and shall be subject to no liability for damages or loss
resulting from the specific use or application made of the Products. Pelco’s liability
for any claim, whether based on breach of contract, negligence, infringement of
any rights of any party or product liability, relating to the Products shall not exceed
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be
liable for any special, incidental, or consequential damages (including loss of use,
loss of profit, and claims of third parties) however caused, whether by the
negligence of Pelco or otherwise.
–
–
–
Fiber optic products
TW3000 Series unshielded twisted pair (UTP) transmission products
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and
MC3651H-2X camera models
• Three years:
–
Pelco-branded fixed camera models (CCC1390H Series, C10DN Series,
C10CH Series, IP3701H Series, and IX Series)
EH1500 Series enclosures
Spectra® IV products (including Spectra IV IP)
Camclosure® Series (IS, ICS, IP) integrated camera systems
–
–
–
–
The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.
DX Series digital video recorders, DVR5100 Series digital video recorders,
Digital Sentry® Series hardware products, DVX Series digital video
recorders, and NVR300 Series network video recorders
Endura® Series distributed network-based video products
Genex® Series products (multiplexers, server, and keyboard)
PMCL200/300/400 Series LCD monitors
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the
following information:
–
–
–
1. Model and serial number
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number
3. Details of the defect or problem
• Two years:
If there is a dispute regarding the warranty of a product that does not fall under
the warranty conditions stated above, please include a written explanation with
the product when returned.
–
–
–
–
Standard varifocal, fixed focal, and motorized zoom lenses
DF5/DF8 Series fixed dome products
Legacy® Series integrated positioning systems
Spectra III™, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, and PS20
scanners, including when used in continuous motion applications.
Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.
–
–
–
–
Esprit Ti and TI2500 Series thermal imaging products
Esprit and WW5700 Series window wiper (excluding wiper blades).
CM6700/CM6800/CM9700 Series matrix
RETURNS
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100
or (559) 292-1981 to obtain an authorization number (CA number if returned for
credit, and RA number if returned for repair) and designated return location.
Digital Light Processing (DLP®) displays (except lamp and color wheel). The
lamp and color wheel will be covered for a period of 90 days. The air filter is
not covered under warranty.
Intelli-M® eIDC controllers
All merchandise returned for credit may be subject to a 20 percent restocking and
refurbishing charge.
–
• One year:
Video cassette recorders (VCRs), except video heads. Video heads will be
covered for a period of six months.
• Six months:
All pan and tilts, scanners, or preset lenses used in continuous motion
applications (preset scan, tour, and auto scan modes).
–
Goods returned for repair or credit should be clearly identified with the assigned
CA or RA number and freight should be prepaid.
–
12-23-08
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic
equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
REVISION HISTORY
Manual #
C785M
C785M-A
Date
12/08
1/09
Comments
Original version.
Added figure 3. Revised information in Flange Focal Adjustment and F-number information in Specifications.
Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.
Sarix and Spectra III are trademarks of Pelco, Inc.
©Copyright 2009, Pelco, Inc. All rights reserved.
202B11714140
USA & Canada • Tel (800) 289-9100 • Fax (800) 289-9150
International • Tel +1 (559) 292-1981 • Fax +1 (559) 348-1120
Download from Www.Somanuals.com. All Manuals Search And Download.
|